gpio: gpiolib: Support for open drain/collector gpios

Adding support for the open drain gpio on which client
can specify the open drain property through GPIO flag
GPIOF_OPEN_DRAIN at the time of gpio request.
The open drain pins are normally pulled high and it
cannot be driven to output with value of 1 and so
when client request for setting the pin to HIGH, the
gpio will be set to input direction to make pin in tristate
and hence PULL-UP on pins will make the state to HIGH.
The open drain pin can be driven to LOW by setting output
with value of 0.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

1 files changed, 42 insertions, 2 deletions

diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index e633a2afbe9..5d25a33d535 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -58,6 +58,7 @@ struct gpio_desc {
 #define FLAG_TRIG_FALL	5	/* trigger on falling edge */
 #define FLAG_TRIG_RISE	6	/* trigger on rising edge */
 #define FLAG_ACTIVE_LOW	7	/* sysfs value has active low */
+#define FLAG_OPEN_DRAIN	8	/* Gpio is open drain type */
 
 #define ID_SHIFT	16	/* add new flags before this one */
 
@@ -1264,6 +1265,7 @@ void gpio_free(unsigned gpio)
 		module_put(desc->chip->owner);
 		clear_bit(FLAG_ACTIVE_LOW, &desc->flags);
 		clear_bit(FLAG_REQUESTED, &desc->flags);
+		clear_bit(FLAG_OPEN_DRAIN, &desc->flags);
 	} else
 		WARN_ON(extra_checks);
 
@@ -1285,6 +1287,9 @@ int gpio_request_one(unsigned gpio, unsigned long flags, const char *label)
 	if (err)
 		return err;
 
+	if (flags & GPIOF_OPEN_DRAIN)
+		set_bit(FLAG_OPEN_DRAIN, &gpio_desc[gpio].flags);
+
 	if (flags & GPIOF_DIR_IN)
 		err = gpio_direction_input(gpio);
 	else
@@ -1434,6 +1439,10 @@ int gpio_direction_output(unsigned gpio, int value)
 	struct gpio_desc	*desc = &gpio_desc[gpio];
 	int			status = -EINVAL;
 
+	/* Open drain pin should not be driven to 1 */
+	if (value && test_bit(FLAG_OPEN_DRAIN,  &desc->flags))
+		return gpio_direction_input(gpio);
+
 	spin_lock_irqsave(&gpio_lock, flags);
 
 	if (!gpio_is_valid(gpio))
@@ -1570,6 +1579,31 @@ int __gpio_get_value(unsigned gpio)
 }
 EXPORT_SYMBOL_GPL(__gpio_get_value);
 
+/*
+ *  _gpio_set_open_drain_value() - Set the open drain gpio's value.
+ * @gpio: Gpio whose state need to be set.
+ * @chip: Gpio chip.
+ * @value: Non-zero for setting it HIGH otherise it will set to LOW.
+ */
+static void _gpio_set_open_drain_value(unsigned gpio,
+			struct gpio_chip *chip, int value)
+{
+	int err = 0;
+	if (value) {
+		err = chip->direction_input(chip, gpio - chip->base);
+		if (!err)
+			clear_bit(FLAG_IS_OUT, &gpio_desc[gpio].flags);
+	} else {
+		err = chip->direction_output(chip, gpio - chip->base, 0);
+		if (!err)
+			set_bit(FLAG_IS_OUT, &gpio_desc[gpio].flags);
+	}
+	trace_gpio_direction(gpio, value, err);
+	if (err < 0)
+		pr_err("%s: Error in set_value for open drain gpio%d err %d\n",
+					__func__, gpio, err);
+}
+
 /**
  * __gpio_set_value() - assign a gpio's value
  * @gpio: gpio whose value will be assigned
@@ -1586,7 +1620,10 @@ void __gpio_set_value(unsigned gpio, int value)
 	chip = gpio_to_chip(gpio);
 	WARN_ON(chip->can_sleep);
 	trace_gpio_value(gpio, 0, value);
-	chip->set(chip, gpio - chip->base, value);
+	if (test_bit(FLAG_OPEN_DRAIN,  &gpio_desc[gpio].flags))
+		_gpio_set_open_drain_value(gpio, chip, value);
+	else
+		chip->set(chip, gpio - chip->base, value);
 }
 EXPORT_SYMBOL_GPL(__gpio_set_value);
 
@@ -1653,7 +1690,10 @@ void gpio_set_value_cansleep(unsigned gpio, int value)
 	might_sleep_if(extra_checks);
 	chip = gpio_to_chip(gpio);
 	trace_gpio_value(gpio, 0, value);
-	chip->set(chip, gpio - chip->base, value);
+	if (test_bit(FLAG_OPEN_DRAIN,  &gpio_desc[gpio].flags))
+		_gpio_set_open_drain_value(gpio, chip, value);
+	else
+		chip->set(chip, gpio - chip->base, value);
 }
 EXPORT_SYMBOL_GPL(gpio_set_value_cansleep);