Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 238 insertions, 0 deletions

diff --git a/include/asm-arm/arch-clps711x/hardware.h b/include/asm-arm/arch-clps711x/hardware.h
new file mode 100644
index 00000000000..1386871e1a5
--- /dev/null
+++ b/include/asm-arm/arch-clps711x/hardware.h
@@ -0,0 +1,238 @@
+/*
+ *  linux/include/asm-arm/arch-clps711x/hardware.h
+ *
+ *  This file contains the hardware definitions of the Prospector P720T.
+ *
+ *  Copyright (C) 2000 Deep Blue Solutions Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#ifndef __ASM_ARCH_HARDWARE_H
+#define __ASM_ARCH_HARDWARE_H
+
+#include <linux/config.h>
+
+#define CLPS7111_VIRT_BASE	0xff000000
+#define CLPS7111_BASE		CLPS7111_VIRT_BASE
+
+/*
+ * The physical addresses that the external chip select signals map to is
+ * dependent on the setting of the nMEDCHG signal on EP7211 and EP7212
+ * processors.  CONFIG_EP72XX_BOOT_ROM is only available if these
+ * processors are in use.
+ */
+#ifndef CONFIG_EP72XX_ROM_BOOT
+#define CS0_PHYS_BASE		(0x00000000)
+#define CS1_PHYS_BASE		(0x10000000)
+#define CS2_PHYS_BASE		(0x20000000)
+#define CS3_PHYS_BASE		(0x30000000)
+#define CS4_PHYS_BASE		(0x40000000)
+#define CS5_PHYS_BASE		(0x50000000)
+#define CS6_PHYS_BASE		(0x60000000)
+#define CS7_PHYS_BASE		(0x70000000)
+#else
+#define CS0_PHYS_BASE		(0x70000000)
+#define CS1_PHYS_BASE		(0x60000000)
+#define CS2_PHYS_BASE		(0x50000000)
+#define CS3_PHYS_BASE		(0x40000000)
+#define CS4_PHYS_BASE		(0x30000000)
+#define CS5_PHYS_BASE		(0x20000000)
+#define CS6_PHYS_BASE		(0x10000000)
+#define CS7_PHYS_BASE		(0x00000000)
+#endif
+
+#if defined (CONFIG_ARCH_EP7211)
+
+#define EP7211_VIRT_BASE	CLPS7111_VIRT_BASE
+#define EP7211_BASE		CLPS7111_VIRT_BASE
+#include <asm/hardware/ep7211.h>
+
+#elif defined (CONFIG_ARCH_EP7212)
+
+#define EP7212_VIRT_BASE	CLPS7111_VIRT_BASE
+#define EP7212_BASE		CLPS7111_VIRT_BASE
+#include <asm/hardware/ep7212.h>
+
+#endif
+
+#define SYSPLD_VIRT_BASE	0xfe000000
+#define SYSPLD_BASE		SYSPLD_VIRT_BASE
+
+#ifndef __ASSEMBLER__
+
+#define PCIO_BASE		IO_BASE
+
+#endif
+
+
+#if  defined (CONFIG_ARCH_AUTCPU12)
+
+#define  CS89712_VIRT_BASE	CLPS7111_VIRT_BASE
+#define  CS89712_BASE		CLPS7111_VIRT_BASE
+
+#include <asm/hardware/clps7111.h>
+#include <asm/hardware/ep7212.h>
+#include <asm/hardware/cs89712.h>
+
+#endif
+
+
+#if defined (CONFIG_ARCH_CDB89712)
+
+#include <asm/hardware/clps7111.h>
+#include <asm/hardware/ep7212.h>
+#include <asm/hardware/cs89712.h>
+
+/* dynamic ioremap() areas */
+#define FLASH_START      0x00000000
+#define FLASH_SIZE       0x800000
+#define FLASH_WIDTH      4
+
+#define SRAM_START       0x60000000
+#define SRAM_SIZE        0xc000
+#define SRAM_WIDTH       4
+
+#define BOOTROM_START    0x70000000
+#define BOOTROM_SIZE     0x80
+#define BOOTROM_WIDTH    4
+
+
+/* static cdb89712_map_io() areas */
+#define REGISTER_START   0x80000000
+#define REGISTER_SIZE    0x4000
+#define REGISTER_BASE    0xff000000
+
+#define ETHER_START      0x20000000
+#define ETHER_SIZE       0x1000
+#define ETHER_BASE       0xfe000000
+
+#endif
+
+
+#if defined (CONFIG_ARCH_EDB7211)
+
+/*
+ * The extra 8 lines of the keyboard matrix are wired to chip select 3 (nCS3) 
+ * and repeat across it. This is the mapping for it.
+ *
+ * In jumpered boot mode, nCS3 is mapped to 0x4000000, not 0x3000000. This 
+ * was cause for much consternation and headscratching. This should probably
+ * be made a compile/run time kernel option.
+ */
+#define EP7211_PHYS_EXTKBD		CS3_PHYS_BASE	/* physical */
+
+#define EP7211_VIRT_EXTKBD		(0xfd000000)	/* virtual */
+
+
+/*
+ * The CS8900A ethernet chip has its I/O registers wired to chip select 2 
+ * (nCS2). This is the mapping for it.
+ *
+ * In jumpered boot mode, nCS2 is mapped to 0x5000000, not 0x2000000. This 
+ * was cause for much consternation and headscratching. This should probably
+ * be made a compile/run time kernel option.
+ */
+#define EP7211_PHYS_CS8900A		CS2_PHYS_BASE	/* physical */
+
+#define EP7211_VIRT_CS8900A		(0xfc000000)	/* virtual */
+
+
+/*
+ * The two flash banks are wired to chip selects 0 and 1. This is the mapping
+ * for them.
+ *
+ * nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running
+ * in jumpered boot mode.
+ */
+#define EP7211_PHYS_FLASH1		CS0_PHYS_BASE	/* physical */
+#define EP7211_PHYS_FLASH2		CS1_PHYS_BASE	/* physical */
+
+#define EP7211_VIRT_FLASH1		(0xfa000000)	/* virtual */
+#define EP7211_VIRT_FLASH2		(0xfb000000)	/* virtual */
+
+#endif /* CONFIG_ARCH_EDB7211 */
+
+
+/*
+ * Relevant bits in port D, which controls power to the various parts of
+ * the LCD on the EDB7211.
+ */
+#define EDB_PD1_LCD_DC_DC_EN	(1<<1)
+#define EDB_PD2_LCDEN		(1<<2)
+#define EDB_PD3_LCDBL		(1<<3)
+
+
+#if defined (CONFIG_ARCH_CEIVA)
+
+#define  CEIVA_VIRT_BASE	CLPS7111_VIRT_BASE
+#define  CEIVA_BASE		CLPS7111_VIRT_BASE
+
+#include <asm/hardware/clps7111.h>
+#include <asm/hardware/ep7212.h>
+
+
+/*
+ * The two flash banks are wired to chip selects 0 and 1. This is the mapping
+ * for them.
+ *
+ * nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running
+ * in jumpered boot mode.
+ */
+#define CEIVA_PHYS_FLASH1	CS0_PHYS_BASE	/* physical */
+#define CEIVA_PHYS_FLASH2	CS1_PHYS_BASE	/* physical */
+
+#define CEIVA_VIRT_FLASH1	(0xfa000000)	/* virtual */
+#define CEIVA_VIRT_FLASH2	(0xfb000000)	/* virtual */
+
+#define CEIVA_FLASH_SIZE        0x100000
+#define CEIVA_FLASH_WIDTH       2
+
+#define SRAM_START       0x60000000
+#define SRAM_SIZE        0xc000
+#define SRAM_WIDTH       4
+
+#define BOOTROM_START    0x70000000
+#define BOOTROM_SIZE     0x80
+#define BOOTROM_WIDTH    4
+
+/*
+ * SED1355 LCD controller
+ */
+#define CEIVA_PHYS_SED1355	CS2_PHYS_BASE
+#define CEIVA_VIRT_SED1355	(0xfc000000)
+
+/*
+ * Relevant bits in port D, which controls power to the various parts of
+ * the LCD on the Ceiva Photo Max, and reset to the LCD controller.
+ */
+
+// Reset line to SED1355 (must be high to operate)
+#define CEIVA_PD1_LCDRST	(1<<1)
+// LCD panel enable (set to one, to enable LCD)
+#define CEIVA_PD4_LCDEN		(1<<4)
+// Backlight (set to one, to turn on backlight
+#define CEIVA_PD5_LCDBL		(1<<5)
+
+/*
+ * Relevant bits in port B, which report the status of the buttons.
+ */
+
+// White button
+#define CEIVA_PB4_WHT_BTN	(1<<4)
+// Black button
+#define CEIVA_PB0_BLK_BTN	(1<<0)
+#endif // #if defined (CONFIG_ARCH_CEIVA)
+
+#endif