i386/x86_64: move headers to include/asm-x86

Move the headers to include/asm-x86 and fixup the
header install make rules

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

1 files changed, 0 insertions, 517 deletions

diff --git a/include/asm-i386/voyager.h b/include/asm-i386/voyager.h
deleted file mode 100644
index 91a9932937a..00000000000
--- a/include/asm-i386/voyager.h
+++ /dev/null
@@ -1,517 +0,0 @@
-/* Copyright (C) 1999,2001
- *
- * Author: J.E.J.Bottomley@HansenPartnership.com
- *
- * Standard include definitions for the NCR Voyager system */
-
-#undef	VOYAGER_DEBUG
-#undef	VOYAGER_CAT_DEBUG
-
-#ifdef VOYAGER_DEBUG
-#define VDEBUG(x)	printk x
-#else
-#define VDEBUG(x)
-#endif
-
-/* There are three levels of voyager machine: 3,4 and 5. The rule is
- * if it's less than 3435 it's a Level 3 except for a 3360 which is
- * a level 4.  A 3435 or above is a Level 5 */
-#define VOYAGER_LEVEL5_AND_ABOVE	0x3435
-#define VOYAGER_LEVEL4			0x3360
-
-/* The L4 DINO ASIC */
-#define VOYAGER_DINO			0x43
-
-/* voyager ports in standard I/O space */
-#define VOYAGER_MC_SETUP	0x96
-
-
-#define	VOYAGER_CAT_CONFIG_PORT			0x97
-#	define VOYAGER_CAT_DESELECT		0xff
-#define VOYAGER_SSPB_RELOCATION_PORT		0x98
-
-/* Valid CAT controller commands */
-/* start instruction register cycle */
-#define VOYAGER_CAT_IRCYC			0x01
-/* start data register cycle */
-#define VOYAGER_CAT_DRCYC			0x02
-/* move to execute state */
-#define VOYAGER_CAT_RUN				0x0F
-/* end operation */
-#define VOYAGER_CAT_END				0x80
-/* hold in idle state */
-#define VOYAGER_CAT_HOLD			0x90
-/* single step an "intest" vector */
-#define VOYAGER_CAT_STEP			0xE0
-/* return cat controller to CLEMSON mode */
-#define VOYAGER_CAT_CLEMSON			0xFF
-
-/* the default cat command header */
-#define VOYAGER_CAT_HEADER			0x7F
-
-/* the range of possible CAT module ids in the system */
-#define VOYAGER_MIN_MODULE			0x10
-#define VOYAGER_MAX_MODULE			0x1f
-
-/* The voyager registers per asic */
-#define VOYAGER_ASIC_ID_REG			0x00
-#define VOYAGER_ASIC_TYPE_REG			0x01
-/* the sub address registers can be made auto incrementing on reads */
-#define VOYAGER_AUTO_INC_REG			0x02
-#	define VOYAGER_AUTO_INC			0x04
-#	define VOYAGER_NO_AUTO_INC		0xfb
-#define VOYAGER_SUBADDRDATA			0x03
-#define VOYAGER_SCANPATH			0x05
-#	define VOYAGER_CONNECT_ASIC		0x01
-#	define VOYAGER_DISCONNECT_ASIC		0xfe
-#define VOYAGER_SUBADDRLO			0x06
-#define VOYAGER_SUBADDRHI			0x07
-#define VOYAGER_SUBMODSELECT			0x08
-#define VOYAGER_SUBMODPRESENT			0x09
-
-#define VOYAGER_SUBADDR_LO			0xff
-#define VOYAGER_SUBADDR_HI			0xffff
-
-/* the maximum size of a scan path -- used to form instructions */
-#define VOYAGER_MAX_SCAN_PATH			0x100
-/* the biggest possible register size (in bytes) */
-#define VOYAGER_MAX_REG_SIZE			4
-
-/* Total number of possible modules (including submodules) */
-#define VOYAGER_MAX_MODULES			16
-/* Largest number of asics per module */
-#define VOYAGER_MAX_ASICS_PER_MODULE		7
-
-/* the CAT asic of each module is always the first one */
-#define VOYAGER_CAT_ID				0
-#define VOYAGER_PSI				0x1a
-
-/* voyager instruction operations and registers */
-#define VOYAGER_READ_CONFIG			0x1
-#define VOYAGER_WRITE_CONFIG			0x2
-#define VOYAGER_BYPASS				0xff
-
-typedef struct voyager_asic 
-{
-	__u8	asic_addr;	/* ASIC address; Level 4 */
-	__u8	asic_type;      /* ASIC type */
-	__u8	asic_id;	/* ASIC id */
-	__u8	jtag_id[4];	/* JTAG id */
-	__u8	asic_location;	/* Location within scan path; start w/ 0 */
-	__u8	bit_location;	/* Location within bit stream; start w/ 0 */
-	__u8	ireg_length;	/* Instruction register length */
-	__u16	subaddr;	/* Amount of sub address space */
-	struct voyager_asic *next;	/* Next asic in linked list */
-} voyager_asic_t;
-
-typedef struct voyager_module {
-	__u8	module_addr;		/* Module address */
-	__u8	scan_path_connected;	/* Scan path connected */
-	__u16   ee_size;		/* Size of the EEPROM */
-	__u16   num_asics;		/* Number of Asics */
-	__u16   inst_bits;		/* Instruction bits in the scan path */
-	__u16   largest_reg;		/* Largest register in the scan path */
-	__u16   smallest_reg;		/* Smallest register in the scan path */
-	voyager_asic_t   *asic;		/* First ASIC in scan path (CAT_I) */
-	struct   voyager_module *submodule;	/* Submodule pointer */ 
-	struct   voyager_module *next;		/* Next module in linked list */
-} voyager_module_t;
-
-typedef struct voyager_eeprom_hdr {
-	 __u8  module_id[4];
-	 __u8  version_id;
-	 __u8  config_id;
-	 __u16 boundry_id;	/* boundary scan id */
-	 __u16 ee_size;		/* size of EEPROM */
-	 __u8  assembly[11];	/* assembly # */
-	 __u8  assembly_rev;	/* assembly rev */
-	 __u8  tracer[4];	/* tracer number */
-	 __u16 assembly_cksum;	/* asm checksum */
-	 __u16 power_consump;	/* pwr requirements */
-	 __u16 num_asics;	/* number of asics */
-	 __u16 bist_time;	/* min. bist time */
-	 __u16 err_log_offset;	/* error log offset */
-	 __u16 scan_path_offset;/* scan path offset */
-	 __u16 cct_offset;
-	 __u16 log_length;	/* length of err log */
-	 __u16 xsum_end;	/* offset to end of
-							   checksum */
-	 __u8  reserved[4];
-	 __u8  sflag;		/* starting sentinal */
-	 __u8  part_number[13];	/* prom part number */
-	 __u8  version[10];	/* version number */
-	 __u8  signature[8];
-	 __u16 eeprom_chksum;
-	 __u32  data_stamp_offset;
-	 __u8  eflag ;		 /* ending sentinal */
-} __attribute__((packed)) voyager_eprom_hdr_t;
-
-
-
-#define VOYAGER_EPROM_SIZE_OFFSET   ((__u16)(&(((voyager_eprom_hdr_t *)0)->ee_size)))
-#define VOYAGER_XSUM_END_OFFSET		0x2a
-
-/* the following three definitions are for internal table layouts
- * in the module EPROMs.  We really only care about the IDs and
- * offsets */
-typedef struct voyager_sp_table {
-	__u8 asic_id;
-	__u8 bypass_flag;
-	__u16 asic_data_offset;
-	__u16 config_data_offset;
-} __attribute__((packed)) voyager_sp_table_t;
-
-typedef struct voyager_jtag_table {
-	__u8 icode[4];
-	__u8 runbist[4];
-	__u8 intest[4];
-	__u8 samp_preld[4];
-	__u8 ireg_len;
-} __attribute__((packed)) voyager_jtt_t;
-
-typedef struct voyager_asic_data_table {
-	__u8 jtag_id[4];
-	__u16 length_bsr;
-	__u16 length_bist_reg;
-	__u32 bist_clk;
-	__u16 subaddr_bits;
-	__u16 seed_bits;
-	__u16 sig_bits;
-	__u16 jtag_offset;
-} __attribute__((packed)) voyager_at_t;
-
-/* Voyager Interrupt Controller (VIC) registers */
-
-/* Base to add to Cross Processor Interrupts (CPIs) when triggering
- * the CPU IRQ line */
-/* register defines for the WCBICs (one per processor) */
-#define VOYAGER_WCBIC0	0x41		/* bus A node P1 processor 0 */
-#define VOYAGER_WCBIC1	0x49		/* bus A node P1 processor 1 */
-#define VOYAGER_WCBIC2	0x51		/* bus A node P2 processor 0 */
-#define VOYAGER_WCBIC3	0x59		/* bus A node P2 processor 1 */
-#define VOYAGER_WCBIC4	0x61		/* bus B node P1 processor 0 */
-#define VOYAGER_WCBIC5	0x69		/* bus B node P1 processor 1 */
-#define VOYAGER_WCBIC6	0x71		/* bus B node P2 processor 0 */
-#define VOYAGER_WCBIC7	0x79		/* bus B node P2 processor 1 */
-
-
-/* top of memory registers */
-#define VOYAGER_WCBIC_TOM_L	0x4
-#define VOYAGER_WCBIC_TOM_H	0x5
-
-/* register defines for Voyager Memory Contol (VMC) 
- * these are present on L4 machines only */
-#define	VOYAGER_VMC1		0x81
-#define VOYAGER_VMC2		0x91
-#define VOYAGER_VMC3		0xa1
-#define VOYAGER_VMC4		0xb1
-
-/* VMC Ports */
-#define VOYAGER_VMC_MEMORY_SETUP	0x9
-#	define VMC_Interleaving		0x01
-#	define VMC_4Way			0x02
-#	define VMC_EvenCacheLines	0x04
-#	define VMC_HighLine		0x08
-#	define VMC_Start0_Enable	0x20
-#	define VMC_Start1_Enable	0x40
-#	define VMC_Vremap		0x80
-#define VOYAGER_VMC_BANK_DENSITY	0xa
-#	define	VMC_BANK_EMPTY		0
-#	define	VMC_BANK_4MB		1
-#	define	VMC_BANK_16MB		2
-#	define	VMC_BANK_64MB		3
-#	define	VMC_BANK0_MASK		0x03
-#	define	VMC_BANK1_MASK		0x0C
-#	define	VMC_BANK2_MASK		0x30
-#	define	VMC_BANK3_MASK		0xC0
-
-/* Magellan Memory Controller (MMC) defines - present on L5 */
-#define VOYAGER_MMC_ASIC_ID		1
-/* the two memory modules corresponding to memory cards in the system */
-#define VOYAGER_MMC_MEMORY0_MODULE	0x14
-#define VOYAGER_MMC_MEMORY1_MODULE	0x15
-/* the Magellan Memory Address (MMA) defines */
-#define VOYAGER_MMA_ASIC_ID		2
-
-/* Submodule number for the Quad Baseboard */
-#define VOYAGER_QUAD_BASEBOARD		1
-
-/* ASIC defines for the Quad Baseboard */
-#define VOYAGER_QUAD_QDATA0		1
-#define VOYAGER_QUAD_QDATA1		2
-#define VOYAGER_QUAD_QABC		3
-
-/* Useful areas in extended CMOS */
-#define VOYAGER_PROCESSOR_PRESENT_MASK	0x88a
-#define VOYAGER_MEMORY_CLICKMAP		0xa23
-#define VOYAGER_DUMP_LOCATION		0xb1a
-
-/* SUS In Control bit - used to tell SUS that we don't need to be
- * babysat anymore */
-#define VOYAGER_SUS_IN_CONTROL_PORT	0x3ff
-#	define VOYAGER_IN_CONTROL_FLAG	0x80
-
-/* Voyager PSI defines */
-#define VOYAGER_PSI_STATUS_REG		0x08
-#	define PSI_DC_FAIL		0x01
-#	define PSI_MON			0x02
-#	define PSI_FAULT		0x04
-#	define PSI_ALARM		0x08
-#	define PSI_CURRENT		0x10
-#	define PSI_DVM			0x20
-#	define PSI_PSCFAULT		0x40
-#	define PSI_STAT_CHG		0x80
-
-#define VOYAGER_PSI_SUPPLY_REG		0x8000
-	/* read */
-#	define PSI_FAIL_DC		0x01
-#	define PSI_FAIL_AC		0x02
-#	define PSI_MON_INT		0x04
-#	define PSI_SWITCH_OFF		0x08
-#	define PSI_HX_OFF		0x10
-#	define PSI_SECURITY		0x20
-#	define PSI_CMOS_BATT_LOW	0x40
-#	define PSI_CMOS_BATT_FAIL	0x80
-	/* write */
-#	define PSI_CLR_SWITCH_OFF	0x13
-#	define PSI_CLR_HX_OFF		0x14
-#	define PSI_CLR_CMOS_BATT_FAIL	0x17
-
-#define VOYAGER_PSI_MASK		0x8001
-#	define PSI_MASK_MASK		0x10
-
-#define VOYAGER_PSI_AC_FAIL_REG		0x8004
-#define	AC_FAIL_STAT_CHANGE		0x80
-
-#define VOYAGER_PSI_GENERAL_REG		0x8007
-	/* read */
-#	define PSI_SWITCH_ON		0x01
-#	define PSI_SWITCH_ENABLED	0x02
-#	define PSI_ALARM_ENABLED	0x08
-#	define PSI_SECURE_ENABLED	0x10
-#	define PSI_COLD_RESET		0x20
-#	define PSI_COLD_START		0x80
-	/* write */
-#	define PSI_POWER_DOWN		0x10
-#	define PSI_SWITCH_DISABLE	0x01
-#	define PSI_SWITCH_ENABLE	0x11
-#	define PSI_CLEAR		0x12
-#	define PSI_ALARM_DISABLE	0x03
-#	define PSI_ALARM_ENABLE		0x13
-#	define PSI_CLEAR_COLD_RESET	0x05
-#	define PSI_SET_COLD_RESET	0x15
-#	define PSI_CLEAR_COLD_START	0x07
-#	define PSI_SET_COLD_START	0x17
-
-
-
-struct voyager_bios_info {
-	__u8	len;
-	__u8	major;
-	__u8	minor;
-	__u8	debug;
-	__u8	num_classes;
-	__u8	class_1;
-	__u8	class_2;
-};
-
-/* The following structures and definitions are for the Kernel/SUS
- * interface these are needed to find out how SUS initialised any Quad
- * boards in the system */
-
-#define	NUMBER_OF_MC_BUSSES	2
-#define SLOTS_PER_MC_BUS	8
-#define MAX_CPUS                16      /* 16 way CPU system */
-#define MAX_PROCESSOR_BOARDS	4	/* 4 processor slot system */
-#define MAX_CACHE_LEVELS	4	/* # of cache levels supported */
-#define MAX_SHARED_CPUS		4	/* # of CPUs that can share a LARC */
-#define NUMBER_OF_POS_REGS	8
-
-typedef struct {
-	__u8	MC_Slot;
-	__u8	POS_Values[NUMBER_OF_POS_REGS];
-} __attribute__((packed)) MC_SlotInformation_t;
-
-struct QuadDescription {
-	__u8  Type;	/* for type 0 (DYADIC or MONADIC) all fields
-                         * will be zero except for slot */
-	__u8 StructureVersion;
-	__u32 CPI_BaseAddress;
-	__u32  LARC_BankSize;
-	__u32 LocalMemoryStateBits;
-	__u8  Slot; /* Processor slots 1 - 4 */
-} __attribute__((packed));
-
-struct ProcBoardInfo { 
-	__u8 Type;
-	__u8 StructureVersion;
-	__u8 NumberOfBoards;
-	struct QuadDescription QuadData[MAX_PROCESSOR_BOARDS];
-} __attribute__((packed));
-
-struct CacheDescription {
-	__u8 Level;
-	__u32 TotalSize;
-	__u16 LineSize;
-	__u8  Associativity;
-	__u8  CacheType;
-	__u8  WriteType;
-	__u8  Number_CPUs_SharedBy;
-	__u8  Shared_CPUs_Hardware_IDs[MAX_SHARED_CPUS];
-
-} __attribute__((packed));
-
-struct CPU_Description {
-	__u8 CPU_HardwareId;
-	char *FRU_String;
-	__u8 NumberOfCacheLevels;
-	struct CacheDescription CacheLevelData[MAX_CACHE_LEVELS];
-} __attribute__((packed));
-
-struct CPU_Info {
-	__u8 Type;
-	__u8 StructureVersion;
-	__u8 NumberOf_CPUs;
-	struct CPU_Description CPU_Data[MAX_CPUS];
-} __attribute__((packed));
-
-
-/*
- * This structure will be used by SUS and the OS.
- * The assumption about this structure is that no blank space is
- * packed in it by our friend the compiler.
- */
-typedef struct {
-	__u8	Mailbox_SUS;		/* Written to by SUS to give commands/response to the OS */
-	__u8	Mailbox_OS;		/* Written to by the OS to give commands/response to SUS */
-	__u8	SUS_MailboxVersion;	/* Tells the OS which iteration of the interface SUS supports */
-	__u8	OS_MailboxVersion;	/* Tells SUS which iteration of the interface the OS supports */
-	__u32	OS_Flags;		/* Flags set by the OS as info for SUS */
-	__u32	SUS_Flags;		/* Flags set by SUS as info for the OS */
-	__u32	WatchDogPeriod;		/* Watchdog period (in seconds) which the DP uses to see if the OS is dead */
-	__u32	WatchDogCount;		/* Updated by the OS on every tic. */
-	__u32	MemoryFor_SUS_ErrorLog;	/* Flat 32 bit address which tells SUS where to stuff the SUS error log on a dump */
-	MC_SlotInformation_t  MC_SlotInfo[NUMBER_OF_MC_BUSSES*SLOTS_PER_MC_BUS];	/* Storage for MCA POS data */
-	/* All new SECOND_PASS_INTERFACE fields added from this point */
-        struct ProcBoardInfo    *BoardData;
-        struct CPU_Info         *CPU_Data;
-	/* All new fields must be added from this point */
-} Voyager_KernelSUS_Mbox_t;
-
-/* structure for finding the right memory address to send a QIC CPI to */
-struct voyager_qic_cpi {
-	/* Each cache line (32 bytes) can trigger a cpi.  The cpi
-	 * read/write may occur anywhere in the cache line---pick the
-	 * middle to be safe */
-	struct  {
-		__u32 pad1[3];
-		__u32 cpi;
-		__u32 pad2[4];
-	} qic_cpi[8];
-};
-
-struct voyager_status {
-	__u32	power_fail:1;
-	__u32	switch_off:1;
-	__u32	request_from_kernel:1;
-};
-
-struct voyager_psi_regs {
-	__u8 cat_id;
-	__u8 cat_dev;
-	__u8 cat_control;
-	__u8 subaddr;
-	__u8 dummy4;
-	__u8 checkbit;
-	__u8 subaddr_low;
-	__u8 subaddr_high;
-	__u8 intstatus;
-	__u8 stat1;
-	__u8 stat3;
-	__u8 fault;
-	__u8 tms;
-	__u8 gen;
-	__u8 sysconf;
-	__u8 dummy15;
-};
-
-struct voyager_psi_subregs {
-	__u8 supply;
-	__u8 mask;
-	__u8 present;
-	__u8 DCfail;
-	__u8 ACfail;
-	__u8 fail;
-	__u8 UPSfail;
-	__u8 genstatus;
-};
-
-struct voyager_psi {
-	struct voyager_psi_regs regs;
-	struct voyager_psi_subregs subregs;
-};
-
-struct voyager_SUS {
-#define	VOYAGER_DUMP_BUTTON_NMI		0x1
-#define VOYAGER_SUS_VALID		0x2
-#define VOYAGER_SYSINT_COMPLETE		0x3
-	__u8	SUS_mbox;
-#define VOYAGER_NO_COMMAND		0x0
-#define VOYAGER_IGNORE_DUMP		0x1
-#define VOYAGER_DO_DUMP			0x2
-#define VOYAGER_SYSINT_HANDSHAKE	0x3
-#define VOYAGER_DO_MEM_DUMP		0x4
-#define VOYAGER_SYSINT_WAS_RECOVERED	0x5
-	__u8	kernel_mbox;
-#define	VOYAGER_MAILBOX_VERSION		0x10
-	__u8	SUS_version;
-	__u8	kernel_version;
-#define VOYAGER_OS_HAS_SYSINT		0x1
-#define VOYAGER_OS_IN_PROGRESS		0x2
-#define VOYAGER_UPDATING_WDPERIOD	0x4
-	__u32	kernel_flags;
-#define VOYAGER_SUS_BOOTING		0x1
-#define VOYAGER_SUS_IN_PROGRESS		0x2
-	__u32	SUS_flags;
-	__u32	watchdog_period;
-	__u32	watchdog_count;
-	__u32	SUS_errorlog;
-	/* lots of system configuration stuff under here */
-};
-	
-/* Variables exported by voyager_smp */
-extern __u32 voyager_extended_vic_processors;
-extern __u32 voyager_allowed_boot_processors;
-extern __u32 voyager_quad_processors;
-extern struct voyager_qic_cpi *voyager_quad_cpi_addr[NR_CPUS];
-extern struct voyager_SUS *voyager_SUS;
-
-/* variables exported always */
-extern struct task_struct *voyager_thread;
-extern int voyager_level;
-extern struct voyager_status voyager_status;
-
-/* functions exported by the voyager and voyager_smp modules */
-extern int voyager_cat_readb(__u8 module, __u8 asic, int reg);
-extern void voyager_cat_init(void);
-extern void voyager_detect(struct voyager_bios_info *);
-extern void voyager_trap_init(void);
-extern void voyager_setup_irqs(void);
-extern int voyager_memory_detect(int region, __u32 *addr, __u32 *length);
-extern void voyager_smp_intr_init(void);
-extern __u8 voyager_extended_cmos_read(__u16 cmos_address);
-extern void voyager_smp_dump(void);
-extern void voyager_timer_interrupt(void);
-extern void smp_local_timer_interrupt(void);
-extern void voyager_power_off(void);
-extern void smp_voyager_power_off(void *dummy);
-extern void voyager_restart(void);
-extern void voyager_cat_power_off(void);
-extern void voyager_cat_do_common_interrupt(void);
-extern void voyager_handle_nmi(void);
-/* Commands for the following are */
-#define	VOYAGER_PSI_READ	0
-#define VOYAGER_PSI_WRITE	1
-#define VOYAGER_PSI_SUBREAD	2
-#define VOYAGER_PSI_SUBWRITE	3
-extern void voyager_cat_psi(__u8, __u16, __u8 *);