[PATCH] Serial: Split 8250 port table (part 2)

Remove legacy ISA serial ports for Accent, Boca, Fourport, Hub6 and MCA
from the architecture specific serial.h include.

The only ports which remain in asm-*/serial.h are the platform specific
entries.  These should really be converted by platform maintainers to
use a platform device, such as can be found in
arch/arm/mach-footbridge/isa.c

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

1 files changed, 1 insertions, 85 deletions

diff --git a/include/asm-ppc/pc_serial.h b/include/asm-ppc/pc_serial.h
index fa9cbb67ce3..8f994f9f885 100644
--- a/include/asm-ppc/pc_serial.h
+++ b/include/asm-ppc/pc_serial.h
@@ -35,93 +35,9 @@
 #define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
 #endif
 
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#define HUB6_FLAGS 0
-#endif
-	
-/*
- * The following define the access methods for the HUB6 card. All
- * access is through two ports for all 24 possible chips. The card is
- * selected through the high 2 bits, the port on that card with the
- * "middle" 3 bits, and the register on that port with the bottom
- * 3 bits.
- *
- * While the access port and interrupt is configurable, the default
- * port locations are 0x302 for the port control register, and 0x303
- * for the data read/write register. Normally, the interrupt is at irq3
- * but can be anything from 3 to 7 inclusive. Note that using 3 will
- * require disabling com2.
- */
-
-#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
-
-#define STD_SERIAL_PORT_DEFNS			\
+#define SERIAL_PORT_DFNS			\
 	/* UART CLK   PORT IRQ     FLAGS        */			\
 	{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS },	/* ttyS0 */	\
 	{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS },	/* ttyS1 */	\
 	{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS },	/* ttyS2 */	\
 	{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS },	/* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS			\
-	{ 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, 	/* ttyS4 */	\
-	{ 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS },	/* ttyS5 */	\
-	{ 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS },	/* ttyS6 */	\
-	{ 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS },	/* ttyS7 */	\
-	{ 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS },	/* ttyS8 */	\
-	{ 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS },	/* ttyS9 */	\
-	{ 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS },	/* ttyS10 */	\
-	{ 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS },	/* ttyS11 */	\
-	{ 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS },	/* ttyS12 */	\
-	{ 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS },	/* ttyS13 */	\
-	{ 0, BASE_BAUD, 0x000, 0, 0 },	/* ttyS14 (spare) */		\
-	{ 0, BASE_BAUD, 0x000, 0, 0 },	/* ttyS15 (spare) */		\
-	{ 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS },	/* ttyS16 */	\
-	{ 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS },	/* ttyS17 */	\
-	{ 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS },	/* ttyS18 */	\
-	{ 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS },	/* ttyS19 */	\
-	{ 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS },	/* ttyS20 */	\
-	{ 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS },	/* ttyS21 */	\
-	{ 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS },	/* ttyS22 */	\
-	{ 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS },	/* ttyS23 */	\
-	{ 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS },	/* ttyS24 */	\
-	{ 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS },	/* ttyS25 */	\
-	{ 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS },	/* ttyS26 */	\
-	{ 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS },	/* ttyS27 */	\
-	{ 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS },	/* ttyS28 */	\
-	{ 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS },	/* ttyS29 */	\
-	{ 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS },	/* ttyS30 */	\
-	{ 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS },	/* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-/* You can have up to four HUB6's in the system, but I've only
- * included two cards here for a total of twelve ports.
- */
-#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
-#define HUB6_SERIAL_PORT_DFNS		\
-	{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) },  /* ttyS32 */	\
-	{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) },  /* ttyS33 */	\
-	{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) },  /* ttyS34 */	\
-	{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) },  /* ttyS35 */	\
-	{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) },  /* ttyS36 */	\
-	{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) },  /* ttyS37 */	\
-	{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) },  /* ttyS38 */	\
-	{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) },  /* ttyS39 */	\
-	{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) },  /* ttyS40 */	\
-	{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) },  /* ttyS41 */	\
-	{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) },  /* ttyS42 */	\
-	{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) },  /* ttyS43 */
-#else
-#define HUB6_SERIAL_PORT_DFNS
-#endif
-
-#define SERIAL_PORT_DFNS		\
-	STD_SERIAL_PORT_DEFNS		\
-	EXTRA_SERIAL_PORT_DEFNS		\
-	HUB6_SERIAL_PORT_DFNS