Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 202 insertions, 0 deletions

diff --git a/include/asm-v850/rte_me2_cb.h b/include/asm-v850/rte_me2_cb.h
new file mode 100644
index 00000000000..9922c85c85a
--- /dev/null
+++ b/include/asm-v850/rte_me2_cb.h
@@ -0,0 +1,202 @@
+/*
+ * include/asm-v850/rte_me2_cb.h -- Midas labs RTE-V850E/ME2-CB board
+ *
+ *  Copyright (C) 2001,02,03  NEC Corporation
+ *  Copyright (C) 2001,02,03  Miles Bader <miles@gnu.org>
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License.  See the file COPYING in the main directory of this
+ * archive for more details.
+ *
+ * Written by Miles Bader <miles@gnu.org>
+ */
+
+#ifndef __V850_RTE_ME2_CB_H__
+#define __V850_RTE_ME2_CB_H__
+
+#include <asm/rte_cb.h>		/* Common defs for Midas RTE-CB boards.  */
+
+
+#define PLATFORM		"rte-v850e/me2-cb"
+#define PLATFORM_LONG		"Midas lab RTE-V850E/ME2-CB"
+
+#define CPU_CLOCK_FREQ		150000000 /* 150MHz */
+#define FIXED_BOGOMIPS		50
+
+/* 32MB of onbard SDRAM.  */
+#define SDRAM_ADDR		0x00800000
+#define SDRAM_SIZE		0x02000000 /* 32MB */
+
+
+/* CPU addresses of GBUS memory spaces.  */
+#define GCS0_ADDR		0x04000000 /* GCS0 - Common SRAM (2MB) */
+#define GCS0_SIZE		0x00800000 /*   8MB */
+#define GCS1_ADDR		0x04800000 /* GCS1 - Flash ROM (8MB) */
+#define GCS1_SIZE		0x00800000 /*   8MB */
+#define GCS2_ADDR		0x07000000 /* GCS2 - I/O registers */
+#define GCS2_SIZE		0x00800000 /*   8MB */
+#define GCS5_ADDR		0x08000000 /* GCS5 - PCI bus space */
+#define GCS5_SIZE		0x02000000 /*   32MB */
+#define GCS6_ADDR		0x07800000 /* GCS6 - PCI control registers */
+#define GCS6_SIZE		0x00800000 /*   8MB */
+
+
+/* For <asm/page.h> */
+#define PAGE_OFFSET 		SDRAM_ADDR
+
+
+#ifdef CONFIG_ROM_KERNEL
+/* Kernel is in ROM, starting at address 0.  */
+
+#define INTV_BASE		0
+#define ROOT_FS_IMAGE_RW	0
+
+#else /* !CONFIG_ROM_KERNEL */
+/* Using RAM-kernel.  Assume some sort of boot-loader got us loaded at
+   address 0.  */
+
+#define INTV_BASE		0
+#define ROOT_FS_IMAGE_RW	1
+
+#endif /* CONFIG_ROM_KERNEL */
+
+
+/* Some misc. on-board devices.  */
+
+/* Seven-segment LED display (four digits).  */
+#define LED_ADDR(n)		(0x0FE02000 + (n))
+#define LED(n)			(*(volatile unsigned char *)LED_ADDR(n))
+#define LED_NUM_DIGITS		4
+
+
+/* On-board PIC.  */
+
+#define CB_PIC_BASE_ADDR 	0x0FE04000
+
+#define CB_PIC_INT0M_ADDR 	(CB_PIC_BASE_ADDR + 0x00)
+#define CB_PIC_INT0M      	(*(volatile u16 *)CB_PIC_INT0M_ADDR)
+#define CB_PIC_INT1M_ADDR 	(CB_PIC_BASE_ADDR + 0x10)
+#define CB_PIC_INT1M      	(*(volatile u16 *)CB_PIC_INT1M_ADDR)
+#define CB_PIC_INTR_ADDR  	(CB_PIC_BASE_ADDR + 0x20)
+#define CB_PIC_INTR       	(*(volatile u16 *)CB_PIC_INTR_ADDR)
+#define CB_PIC_INTEN_ADDR 	(CB_PIC_BASE_ADDR + 0x30)
+#define CB_PIC_INTEN      	(*(volatile u16 *)CB_PIC_INTEN_ADDR)
+
+#define CB_PIC_INT0EN        	0x0001
+#define CB_PIC_INT1EN        	0x0002
+#define CB_PIC_INT0SEL       	0x0080
+
+/* The PIC interrupts themselves.  */
+#define CB_PIC_BASE_IRQ		NUM_CPU_IRQS
+#define IRQ_CB_PIC_NUM		10
+
+/* Some specific CB_PIC interrupts. */
+#define IRQ_CB_EXTTM0		(CB_PIC_BASE_IRQ + 0)
+#define IRQ_CB_EXTSIO		(CB_PIC_BASE_IRQ + 1)
+#define IRQ_CB_TOVER		(CB_PIC_BASE_IRQ + 2)
+#define IRQ_CB_GINT0		(CB_PIC_BASE_IRQ + 3)
+#define IRQ_CB_USB		(CB_PIC_BASE_IRQ + 4)
+#define IRQ_CB_LANC		(CB_PIC_BASE_IRQ + 5)
+#define IRQ_CB_USB_VBUS_ON	(CB_PIC_BASE_IRQ + 6)
+#define IRQ_CB_USB_VBUS_OFF	(CB_PIC_BASE_IRQ + 7)
+#define IRQ_CB_EXTTM1		(CB_PIC_BASE_IRQ + 8)
+#define IRQ_CB_EXTTM2		(CB_PIC_BASE_IRQ + 9)
+
+/* The GBUS GINT1 - GINT3 (note, not GINT0!) interrupts are connected to
+   the INTP65 - INTP67 pins on the CPU.  These are shared among the GBUS
+   interrupts.  */
+#define IRQ_GINT(n)		IRQ_INTP((n) + 9)  /* 0 is unused! */
+#define IRQ_GINT_NUM		4		   /* 0 is unused! */
+
+/* The shared interrupt line from the PIC is connected to CPU pin INTP23.  */
+#define IRQ_CB_PIC		IRQ_INTP(4) /* P23 */
+
+/* Used by <asm/rte_cb.h> to derive NUM_MACH_IRQS.  */
+#define NUM_RTE_CB_IRQS		(NUM_CPU_IRQS + IRQ_CB_PIC_NUM)
+
+
+#ifndef __ASSEMBLY__
+struct cb_pic_irq_init {
+	const char *name;	/* name of interrupt type */
+
+	/* Range of kernel irq numbers for this type:
+	   BASE, BASE+INTERVAL, ..., BASE+INTERVAL*NUM  */
+	unsigned base, num, interval;
+
+	unsigned priority;	/* interrupt priority to assign */
+};
+struct hw_interrupt_type;	/* fwd decl */
+
+/* Enable interrupt handling for interrupt IRQ.  */
+extern void cb_pic_enable_irq (unsigned irq);
+/* Disable interrupt handling for interrupt IRQ.  Note that any interrupts
+   received while disabled will be delivered once the interrupt is enabled
+   again, unless they are explicitly cleared using `cb_pic_clear_pending_irq'.  */
+extern void cb_pic_disable_irq (unsigned irq);
+/* Initialize HW_IRQ_TYPES for PIC irqs described in array INITS (which is
+   terminated by an entry with the name field == 0).  */
+extern void cb_pic_init_irq_types (struct cb_pic_irq_init *inits,
+				   struct hw_interrupt_type *hw_irq_types);
+/* Initialize PIC interrupts.  */
+extern void cb_pic_init_irqs (void);
+#endif /* __ASSEMBLY__ */
+
+
+/* TL16C550C on board UART see also asm/serial.h */
+#define CB_UART_BASE    	0x0FE08000
+#define CB_UART_REG_GAP 	0x10
+#define CB_UART_CLOCK   	0x16000000
+
+/* CompactFlash setting */
+#define CB_CF_BASE     		0x0FE0C000
+#define CB_CF_CCR_ADDR 		(CB_CF_BASE+0x200)
+#define CB_CF_CCR      		(*(volatile u8 *)CB_CF_CCR_ADDR)
+#define CB_CF_REG0_ADDR		(CB_CF_BASE+0x1000)
+#define CB_CF_REG0     		(*(volatile u16 *)CB_CF_REG0_ADDR)
+#define CB_CF_STS0_ADDR		(CB_CF_BASE+0x1004)
+#define CB_CF_STS0     		(*(volatile u16 *)CB_CF_STS0_ADDR)
+#define CB_PCATA_BASE  		(CB_CF_BASE+0x800)
+#define CB_IDE_BASE    		(CB_CF_BASE+0x9F0)
+#define CB_IDE_CTRL    		(CB_CF_BASE+0xBF6)
+#define CB_IDE_REG_OFFS		0x1
+
+
+/* SMSC LAN91C111 setting */
+#if defined(CONFIG_SMC91111)
+#define CB_LANC_BASE 		0x0FE10300
+#define CONFIG_SMC16BITONLY
+#define ETH0_ADDR 		CB_LANC_BASE
+#define ETH0_IRQ 		IRQ_CB_LANC
+#endif /* CONFIG_SMC16BITONLY */
+
+
+#undef V850E_UART_PRE_CONFIGURE
+#define V850E_UART_PRE_CONFIGURE	rte_me2_cb_uart_pre_configure
+#ifndef __ASSEMBLY__
+extern void rte_me2_cb_uart_pre_configure (unsigned chan,
+					   unsigned cflags, unsigned baud);
+#endif /* __ASSEMBLY__ */
+
+/* This board supports RTS/CTS for the on-chip UART, but only for channel 0. */
+
+/* CTS for UART channel 0 is pin P22 (bit 2 of port 2).  */
+#define V850E_UART_CTS(chan)	((chan) == 0 ? !(ME2_PORT2_IO & 0x4) : 1)
+/* RTS for UART channel 0 is pin P21 (bit 1 of port 2).  */
+#define V850E_UART_SET_RTS(chan, val)					      \
+   do {									      \
+	   if (chan == 0) {						      \
+		   unsigned old = ME2_PORT2_IO; 			      \
+		   if (val)						      \
+			   ME2_PORT2_IO = old & ~0x2;			      \
+		   else							      \
+			   ME2_PORT2_IO = old | 0x2;			      \
+	   }								      \
+   } while (0)
+
+
+#ifndef __ASSEMBLY__
+extern void rte_me2_cb_init_irqs (void);
+#endif /* !__ASSEMBLY__ */
+
+
+#endif /* __V850_RTE_ME2_CB_H__ */