spi/pl022: add support for the PL023 derivate

This adds support for a further ST variant of the PL022 called
PL023. Some differences in the control registers due to being
stripped down to SPI mode only, and a new clock feedback sample
delay config setting is available.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

1 files changed, 30 insertions, 2 deletions

diff --git a/include/linux/amba/pl022.h b/include/linux/amba/pl022.h
index 612f3991334..abf26cc47a2 100644
--- a/include/linux/amba/pl022.h
+++ b/include/linux/amba/pl022.h
@@ -182,8 +182,8 @@ enum ssp_microwire_wait_state {
 };
 
 /**
- * enum Microwire - whether Full/Half Duplex, only available
- * in the ST Micro variant.
+ * enum ssp_duplex - whether Full/Half Duplex on microwire, only
+ * available in the ST Micro variant.
  * @SSP_MICROWIRE_CHANNEL_FULL_DUPLEX: SSPTXD becomes bi-directional,
  *     SSPRXD not used
  * @SSP_MICROWIRE_CHANNEL_HALF_DUPLEX: SSPTXD is an output, SSPRXD is
@@ -195,6 +195,31 @@ enum ssp_duplex {
 };
 
 /**
+ * enum ssp_clkdelay - an optional clock delay on the feedback clock
+ * only available in the ST Micro PL023 variant.
+ * @SSP_FEEDBACK_CLK_DELAY_NONE: no delay, the data coming in from the
+ * slave is sampled directly
+ * @SSP_FEEDBACK_CLK_DELAY_1T: the incoming slave data is sampled with
+ * a delay of T-dt
+ * @SSP_FEEDBACK_CLK_DELAY_2T: dito with a delay if 2T-dt
+ * @SSP_FEEDBACK_CLK_DELAY_3T: dito with a delay if 3T-dt
+ * @SSP_FEEDBACK_CLK_DELAY_4T: dito with a delay if 4T-dt
+ * @SSP_FEEDBACK_CLK_DELAY_5T: dito with a delay if 5T-dt
+ * @SSP_FEEDBACK_CLK_DELAY_6T: dito with a delay if 6T-dt
+ * @SSP_FEEDBACK_CLK_DELAY_7T: dito with a delay if 7T-dt
+ */
+enum ssp_clkdelay {
+	SSP_FEEDBACK_CLK_DELAY_NONE,
+	SSP_FEEDBACK_CLK_DELAY_1T,
+	SSP_FEEDBACK_CLK_DELAY_2T,
+	SSP_FEEDBACK_CLK_DELAY_3T,
+	SSP_FEEDBACK_CLK_DELAY_4T,
+	SSP_FEEDBACK_CLK_DELAY_5T,
+	SSP_FEEDBACK_CLK_DELAY_6T,
+	SSP_FEEDBACK_CLK_DELAY_7T
+};
+
+/**
  * CHIP select/deselect commands
  */
 enum ssp_chip_select {
@@ -237,6 +262,8 @@ struct pl022_ssp_controller {
  * @ctrl_len: Microwire interface: Control length
  * @wait_state: Microwire interface: Wait state
  * @duplex: Microwire interface: Full/Half duplex
+ * @clkdelay: on the PL023 variant, the delay in feeback clock cycles
+ * before sampling the incoming line
  * @cs_control: function pointer to board-specific function to
  * assert/deassert I/O port to control HW generation of devices chip-select.
  * @dma_xfer_type: Type of DMA xfer (Mem-to-periph or Periph-to-Periph)
@@ -260,6 +287,7 @@ struct pl022_config_chip {
 	enum ssp_microwire_ctrl_len ctrl_len;
 	enum ssp_microwire_wait_state wait_state;
 	enum ssp_duplex duplex;
+	enum ssp_clkdelay clkdelay;
 	void (*cs_control) (u32 control);
 };