[MTD] Refactor NAND hwcontrol to cmd_ctrl

The hwcontrol function enforced a step by step state machine
for any kind of hardware chip access. Let the hardware driver
know which control bits are set and inform it about a change
of the control lines. Let the hardware driver write out the
command and address bytes directly. This gives a peformance
advantage for address bus controlled chips and simplifies the
quirks in the hardware drivers.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

1 files changed, 17 insertions, 16 deletions

diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h
index 8362b466df3..e9a93526315 100644
--- a/include/linux/mtd/nand.h
+++ b/include/linux/mtd/nand.h
@@ -50,23 +50,20 @@ extern int nand_write_raw(struct mtd_info *mtd, loff_t to, size_t len,
 
 /*
  * Constants for hardware specific CLE/ALE/NCE function
-*/
+ *
+ * These are bits which can be or'ed to set/clear multiple
+ * bits in one go.
+ */
 /* Select the chip by setting nCE to low */
-#define NAND_CTL_SETNCE		1
-/* Deselect the chip by setting nCE to high */
-#define NAND_CTL_CLRNCE		2
+#define NAND_NCE		0x01
 /* Select the command latch by setting CLE to high */
-#define NAND_CTL_SETCLE		3
-/* Deselect the command latch by setting CLE to low */
-#define NAND_CTL_CLRCLE		4
+#define NAND_CLE		0x02
 /* Select the address latch by setting ALE to high */
-#define NAND_CTL_SETALE		5
-/* Deselect the address latch by setting ALE to low */
-#define NAND_CTL_CLRALE		6
-/* Set write protection by setting WP to high. Not used! */
-#define NAND_CTL_SETWP		7
-/* Clear write protection by setting WP to low. Not used! */
-#define NAND_CTL_CLRWP		8
+#define NAND_ALE		0x04
+
+#define NAND_CTRL_CLE		(NAND_NCE | NAND_CLE)
+#define NAND_CTRL_ALE		(NAND_NCE | NAND_ALE)
+#define NAND_CTRL_CHANGE	0x80
 
 /*
  * Standard NAND flash commands
@@ -106,6 +103,8 @@ extern int nand_write_raw(struct mtd_info *mtd, loff_t to, size_t len,
 #define NAND_CMD_STATUS_RESET	0x7f
 #define NAND_CMD_STATUS_CLEAR	0xff
 
+#define NAND_CMD_NONE		-1
+
 /* Status bits */
 #define NAND_STATUS_FAIL	0x01
 #define NAND_STATUS_FAIL_N1	0x02
@@ -263,7 +262,8 @@ struct nand_ecc_ctrl {
  * @select_chip:	[REPLACEABLE] select chip nr
  * @block_bad:		[REPLACEABLE] check, if the block is bad
  * @block_markbad:	[REPLACEABLE] mark the block bad
- * @hwcontrol:		[BOARDSPECIFIC] hardwarespecific function for accesing control-lines
+ * @cmd_ctrl:		[BOARDSPECIFIC] hardwarespecific funtion for controlling
+ *			ALE/CLE/nCE. Also used to write command and address
  * @dev_ready:		[BOARDSPECIFIC] hardwarespecific function for accesing device ready/busy line
  *			If set to NULL no access to ready/busy is available and the ready/busy information
  *			is read from the chip status register
@@ -317,7 +317,8 @@ struct nand_chip {
 	void		(*select_chip)(struct mtd_info *mtd, int chip);
 	int		(*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip);
 	int		(*block_markbad)(struct mtd_info *mtd, loff_t ofs);
-	void		(*hwcontrol)(struct mtd_info *mtd, int cmd);
+	void		(*cmd_ctrl)(struct mtd_info *mtd, int dat,
+				    unsigned int ctrl);
 	int		(*dev_ready)(struct mtd_info *mtd);
 	void		(*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, int page_addr);
 	int		(*waitfunc)(struct mtd_info *mtd, struct nand_chip *this, int state);