Merge tag 'v3.1-rc6' into staging/for_v3.2

* tag 'v3.1-rc6': (1902 commits)
  Linux 3.1-rc6
  ioctl: register LTTng ioctl
  fuse: fix memory leak
  fuse: fix flock breakage
  Btrfs: add dummy extent if dst offset excceeds file end in
  Btrfs: calc file extent num_bytes correctly in file clone
  btrfs: xattr: fix attribute removal
  Btrfs: fix wrong nbytes information of the inode
  Btrfs: fix the file extent gap when doing direct IO
  Btrfs: fix unclosed transaction handle in btrfs_cont_expand
  Btrfs: fix misuse of trans block rsv
  Btrfs: reset to appropriate block rsv after orphan operations
  Btrfs: skip locking if searching the commit root in csum lookup
  btrfs: fix warning in iput for bad-inode
  Btrfs: fix an oops when deleting snapshots
  [media] vp7045: fix buffer setup
  [media] nuvoton-cir: simplify raw IR sample handling
  [media] [Resend] viacam: Don't explode if pci_find_bus() returns NULL
  [media] v4l2: Fix documentation of the codec device controls
  [media] gspca - sonixj: Fix the darkness of sensor om6802 in 320x240
  ...

1 files changed, 26 insertions, 1 deletions

diff --git a/include/linux/ti_wilink_st.h b/include/linux/ti_wilink_st.h
index b004e557caa..2ef4385da6b 100644
--- a/include/linux/ti_wilink_st.h
+++ b/include/linux/ti_wilink_st.h
@@ -410,7 +410,28 @@ struct gps_event_hdr {
 	u16 plen;
 } __attribute__ ((packed));
 
-/* platform data */
+/**
+ * struct ti_st_plat_data - platform data shared between ST driver and
+ *	platform specific board file which adds the ST device.
+ * @nshutdown_gpio: Host's GPIO line to which chip's BT_EN is connected.
+ * @dev_name: The UART/TTY name to which chip is interfaced. (eg: /dev/ttyS1)
+ * @flow_cntrl: Should always be 1, since UART's CTS/RTS is used for PM
+ *	purposes.
+ * @baud_rate: The baud rate supported by the Host UART controller, this will
+ *	be shared across with the chip via a HCI VS command from User-Space Init
+ *	Mgr application.
+ * @suspend:
+ * @resume: legacy PM routines hooked to platform specific board file, so as
+ *	to take chip-host interface specific action.
+ * @chip_enable:
+ * @chip_disable: Platform/Interface specific mux mode setting, GPIO
+ *	configuring, Host side PM disabling etc.. can be done here.
+ * @chip_asleep:
+ * @chip_awake: Chip specific deep sleep states is communicated to Host
+ *	specific board-xx.c to take actions such as cut UART clocks when chip
+ *	asleep or run host faster when chip awake etc..
+ *
+ */
 struct ti_st_plat_data {
 	long nshutdown_gpio;
 	unsigned char dev_name[UART_DEV_NAME_LEN]; /* uart name */
@@ -418,6 +439,10 @@ struct ti_st_plat_data {
 	unsigned long baud_rate;
 	int (*suspend)(struct platform_device *, pm_message_t);
 	int (*resume)(struct platform_device *);
+	int (*chip_enable) (struct kim_data_s *);
+	int (*chip_disable) (struct kim_data_s *);
+	int (*chip_asleep) (struct kim_data_s *);
+	int (*chip_awake) (struct kim_data_s *);
 };
 
 #endif /* TI_WILINK_ST_H */