USB: move usbcore away from hcd->state

The hcd->state variable is a disaster.  It's not clearly owned by
either usbcore or the host controller drivers, and they both change it
from time to time, potentially stepping on each other's toes.  It's
not protected by any locks.  And there's no mechanism to prevent it
from going through an invalid transition.

This patch (as1451) takes a first step toward fixing these problems.
As it turns out, usbcore uses hcd->state for essentially only two
things: checking whether the controller's root hub is running and
checking whether the controller has died.  Therefore the patch adds
two new atomic bitflags to the hcd structure, to store these pieces of
information.  The new flags are used only by usbcore, and a private
spinlock prevents invalid combinations (a dead controller's root hub
cannot be running).

The patch does not change the places where usbcore sets hcd->state,
since HCDs may depend on them.  Furthermore, there is one place in
usb_hcd_irq() where usbcore still must use hcd->state: An HCD's
interrupt handler can implicitly indicate that the controller died by
setting hcd->state to HC_STATE_HALT.  Nevertheless, the new code is a
big improvement over the current code.

The patch makes one other change.  The hcd_bus_suspend() and
hcd_bus_resume() routines now check first whether the host controller
has died; if it has then they return immediately without calling the
HCD's bus_suspend or bus_resume methods.

This fixes the major problem reported in Bugzilla #29902: The system
fails to suspend after a host controller dies during system resume.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alex Terekhov <a.terekhov@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 4 insertions, 0 deletions

diff --git a/include/linux/usb/hcd.h b/include/linux/usb/hcd.h
index 9cfba4f2457..8b65068c6af 100644
--- a/include/linux/usb/hcd.h
+++ b/include/linux/usb/hcd.h
@@ -99,6 +99,8 @@ struct usb_hcd {
 #define HCD_FLAG_POLL_RH		2	/* poll for rh status? */
 #define HCD_FLAG_POLL_PENDING		3	/* status has changed? */
 #define HCD_FLAG_WAKEUP_PENDING		4	/* root hub is resuming? */
+#define HCD_FLAG_RH_RUNNING		5	/* root hub is running? */
+#define HCD_FLAG_DEAD			6	/* controller has died? */
 
 	/* The flags can be tested using these macros; they are likely to
 	 * be slightly faster than test_bit().
@@ -108,6 +110,8 @@ struct usb_hcd {
 #define HCD_POLL_RH(hcd)	((hcd)->flags & (1U << HCD_FLAG_POLL_RH))
 #define HCD_POLL_PENDING(hcd)	((hcd)->flags & (1U << HCD_FLAG_POLL_PENDING))
 #define HCD_WAKEUP_PENDING(hcd)	((hcd)->flags & (1U << HCD_FLAG_WAKEUP_PENDING))
+#define HCD_RH_RUNNING(hcd)	((hcd)->flags & (1U << HCD_FLAG_RH_RUNNING))
+#define HCD_DEAD(hcd)		((hcd)->flags & (1U << HCD_FLAG_DEAD))
 
 	/* Flags that get set only during HCD registration or removal. */
 	unsigned		rh_registered:1;/* is root hub registered? */