Merge branch 'usb-next' into musb-merge

* usb-next: (132 commits)
  USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
  USB: uas: Ensure we only bind to a UAS interface
  USB: uas: Rename sense pipe and sense urb to status pipe and status urb
  USB: uas: Use kzalloc instead of kmalloc
  USB: uas: Fix up the Sense IU
  usb: musb: core: kill unneeded #include's
  DA8xx: assign name to MUSB IRQ resource
  usb: gadget: g_ncm added
  usb: gadget: f_ncm.c added
  usb: gadget: u_ether: prepare for NCM
  usb: pch_udc: Fix setup transfers with data out
  usb: pch_udc: Fix compile error, warnings and checkpatch warnings
  usb: add ab8500 usb transceiver driver
  USB: gadget: Implement runtime PM for MSM bus glue driver
  USB: gadget: Implement runtime PM for ci13xxx gadget
  USB: gadget: Add USB controller driver for MSM SoC
  USB: gadget: Introduce ci13xxx_udc_driver struct
  USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
  USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
  USB: gadget: Separate out PCI bus code from ci13xxx_udc
  ...

7 files changed, 237 insertions, 5 deletions

diff --git a/include/linux/usb/ch11.h b/include/linux/usb/ch11.h
index 119194c85d1..10ec0699bea 100644
--- a/include/linux/usb/ch11.h
+++ b/include/linux/usb/ch11.h
@@ -28,6 +28,13 @@
 #define HUB_STOP_TT		11
 
 /*
+ * Hub class additional requests defined by USB 3.0 spec
+ * See USB 3.0 spec Table 10-6
+ */
+#define HUB_SET_DEPTH		12
+#define HUB_GET_PORT_ERR_COUNT	13
+
+/*
  * Hub Class feature numbers
  * See USB 2.0 spec Table 11-17
  */
@@ -56,6 +63,20 @@
 #define USB_PORT_FEAT_C_PORT_L1         23
 
 /*
+ * Port feature selectors added by USB 3.0 spec.
+ * See USB 3.0 spec Table 10-7
+ */
+#define USB_PORT_FEAT_LINK_STATE		5
+#define USB_PORT_FEAT_U1_TIMEOUT		23
+#define USB_PORT_FEAT_U2_TIMEOUT		24
+#define USB_PORT_FEAT_C_LINK_STATE		25
+#define USB_PORT_FEAT_C_CONFIG_ERR		26
+#define USB_PORT_FEAT_REMOTE_WAKE_MASK		27
+#define USB_PORT_FEAT_BH_PORT_RESET		28
+#define USB_PORT_FEAT_C_BH_PORT_RESET		29
+#define USB_PORT_FEAT_FORCE_LINKPM_ACCEPT	30
+
+/*
  * Hub Status and Hub Change results
  * See USB 2.0 spec Table 11-19 and Table 11-20
  */
@@ -84,6 +105,32 @@ struct usb_port_status {
 #define USB_PORT_STAT_SUPER_SPEED	0x8000	/* Linux-internal */
 
 /*
+ * Additions to wPortStatus bit field from USB 3.0
+ * See USB 3.0 spec Table 10-10
+ */
+#define USB_PORT_STAT_LINK_STATE	0x01e0
+#define USB_SS_PORT_STAT_POWER		0x0200
+#define USB_PORT_STAT_SPEED_5GBPS	0x0000
+/* Valid only if port is enabled */
+
+/*
+ * Definitions for PORT_LINK_STATE values
+ * (bits 5-8) in wPortStatus
+ */
+#define USB_SS_PORT_LS_U0		0x0000
+#define USB_SS_PORT_LS_U1		0x0020
+#define USB_SS_PORT_LS_U2		0x0040
+#define USB_SS_PORT_LS_U3		0x0060
+#define USB_SS_PORT_LS_SS_DISABLED	0x0080
+#define USB_SS_PORT_LS_RX_DETECT	0x00a0
+#define USB_SS_PORT_LS_SS_INACTIVE	0x00c0
+#define USB_SS_PORT_LS_POLLING		0x00e0
+#define USB_SS_PORT_LS_RECOVERY		0x0100
+#define USB_SS_PORT_LS_HOT_RESET	0x0120
+#define USB_SS_PORT_LS_COMP_MOD		0x0140
+#define USB_SS_PORT_LS_LOOPBACK		0x0160
+
+/*
  * wPortChange bit field
  * See USB 2.0 spec Table 11-22
  * Bits 0 to 4 shown, bits 5 to 15 are reserved
diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h
index f917bbbc890..ab461948b57 100644
--- a/include/linux/usb/ch9.h
+++ b/include/linux/usb/ch9.h
@@ -124,6 +124,16 @@
 #define USB_DEVICE_DEBUG_MODE		6	/* (special devices only) */
 
 /*
+ * Test Mode Selectors
+ * See USB 2.0 spec Table 9-7
+ */
+#define	TEST_J		1
+#define	TEST_K		2
+#define	TEST_SE0_NAK	3
+#define	TEST_PACKET	4
+#define	TEST_FORCE_EN	5
+
+/*
  * New Feature Selectors as added by USB 3.0
  * See USB 3.0 spec Table 9-6
  */
diff --git a/include/linux/usb/hcd.h b/include/linux/usb/hcd.h
index 0b6e751ea0b..dd6ee49a084 100644
--- a/include/linux/usb/hcd.h
+++ b/include/linux/usb/hcd.h
@@ -471,6 +471,10 @@ extern void usb_ep0_reinit(struct usb_device *);
 
 /*-------------------------------------------------------------------------*/
 
+/* class requests from USB 3.0 hub spec, table 10-5 */
+#define SetHubDepth		(0x3000 | HUB_SET_DEPTH)
+#define GetPortErrorCount	(0x8000 | HUB_GET_PORT_ERR_COUNT)
+
 /*
  * Generic bandwidth allocation constants/support
  */
diff --git a/include/linux/usb/msm_hsusb.h b/include/linux/usb/msm_hsusb.h
new file mode 100644
index 00000000000..3675e03b153
--- /dev/null
+++ b/include/linux/usb/msm_hsusb.h
@@ -0,0 +1,112 @@
+/* linux/include/asm-arm/arch-msm/hsusb.h
+ *
+ * Copyright (C) 2008 Google, Inc.
+ * Author: Brian Swetland <swetland@google.com>
+ * Copyright (c) 2009-2010, Code Aurora Forum. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __ASM_ARCH_MSM_HSUSB_H
+#define __ASM_ARCH_MSM_HSUSB_H
+
+#include <linux/types.h>
+#include <linux/usb/otg.h>
+
+/**
+ * Supported USB modes
+ *
+ * USB_PERIPHERAL       Only peripheral mode is supported.
+ * USB_HOST             Only host mode is supported.
+ * USB_OTG              OTG mode is supported.
+ *
+ */
+enum usb_mode_type {
+	USB_NONE = 0,
+	USB_PERIPHERAL,
+	USB_HOST,
+	USB_OTG,
+};
+
+/**
+ * OTG control
+ *
+ * OTG_NO_CONTROL	Id/VBUS notifications not required. Useful in host
+ *                      only configuration.
+ * OTG_PHY_CONTROL	Id/VBUS notifications comes form USB PHY.
+ * OTG_PMIC_CONTROL	Id/VBUS notifications comes from PMIC hardware.
+ * OTG_USER_CONTROL	Id/VBUS notifcations comes from User via sysfs.
+ *
+ */
+enum otg_control_type {
+	OTG_NO_CONTROL = 0,
+	OTG_PHY_CONTROL,
+	OTG_PMIC_CONTROL,
+	OTG_USER_CONTROL,
+};
+
+/**
+ * struct msm_otg_platform_data - platform device data
+ *              for msm72k_otg driver.
+ * @phy_init_seq: PHY configuration sequence. val, reg pairs
+ *              terminated by -1.
+ * @vbus_power: VBUS power on/off routine.
+ * @power_budget: VBUS power budget in mA (0 will be treated as 500mA).
+ * @mode: Supported mode (OTG/peripheral/host).
+ * @otg_control: OTG switch controlled by user/Id pin
+ * @default_mode: Default operational mode. Applicable only if
+ *              OTG switch is controller by user.
+ *
+ */
+struct msm_otg_platform_data {
+	int *phy_init_seq;
+	void (*vbus_power)(bool on);
+	unsigned power_budget;
+	enum usb_mode_type mode;
+	enum otg_control_type otg_control;
+	enum usb_mode_type default_mode;
+	void (*setup_gpio)(enum usb_otg_state state);
+};
+
+/**
+ * struct msm_otg: OTG driver data. Shared by HCD and DCD.
+ * @otg: USB OTG Transceiver structure.
+ * @pdata: otg device platform data.
+ * @irq: IRQ number assigned for HSUSB controller.
+ * @clk: clock struct of usb_hs_clk.
+ * @pclk: clock struct of usb_hs_pclk.
+ * @phy_reset_clk: clock struct of usb_phy_clk.
+ * @core_clk: clock struct of usb_hs_core_clk.
+ * @regs: ioremapped register base address.
+ * @inputs: OTG state machine inputs(Id, SessValid etc).
+ * @sm_work: OTG state machine work.
+ * @in_lpm: indicates low power mode (LPM) state.
+ * @async_int: Async interrupt arrived.
+ *
+ */
+struct msm_otg {
+	struct otg_transceiver otg;
+	struct msm_otg_platform_data *pdata;
+	int irq;
+	struct clk *clk;
+	struct clk *pclk;
+	struct clk *phy_reset_clk;
+	struct clk *core_clk;
+	void __iomem *regs;
+#define ID		0
+#define B_SESS_VLD	1
+	unsigned long inputs;
+	struct work_struct sm_work;
+	atomic_t in_lpm;
+	int async_int;
+};
+
+#endif
diff --git a/include/linux/usb/msm_hsusb_hw.h b/include/linux/usb/msm_hsusb_hw.h
new file mode 100644
index 00000000000..b92e17349c7
--- /dev/null
+++ b/include/linux/usb/msm_hsusb_hw.h
@@ -0,0 +1,59 @@
+/*
+ * Copyright (C) 2007 Google, Inc.
+ * Author: Brian Swetland <swetland@google.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __LINUX_USB_GADGET_MSM72K_UDC_H__
+#define __LINUX_USB_GADGET_MSM72K_UDC_H__
+
+#ifdef CONFIG_ARCH_MSM7X00A
+#define USB_SBUSCFG          (MSM_USB_BASE + 0x0090)
+#else
+#define USB_AHBBURST         (MSM_USB_BASE + 0x0090)
+#define USB_AHBMODE          (MSM_USB_BASE + 0x0098)
+#endif
+#define USB_CAPLENGTH        (MSM_USB_BASE + 0x0100) /* 8 bit */
+
+#define USB_USBCMD           (MSM_USB_BASE + 0x0140)
+#define USB_PORTSC           (MSM_USB_BASE + 0x0184)
+#define USB_OTGSC            (MSM_USB_BASE + 0x01A4)
+#define USB_USBMODE          (MSM_USB_BASE + 0x01A8)
+
+#define USBCMD_RESET   2
+#define USB_USBINTR          (MSM_USB_BASE + 0x0148)
+
+#define PORTSC_PHCD            (1 << 23) /* phy suspend mode */
+#define PORTSC_PTS_MASK         (3 << 30)
+#define PORTSC_PTS_ULPI         (3 << 30)
+
+#define USB_ULPI_VIEWPORT    (MSM_USB_BASE + 0x0170)
+#define ULPI_RUN              (1 << 30)
+#define ULPI_WRITE            (1 << 29)
+#define ULPI_READ             (0 << 29)
+#define ULPI_ADDR(n)          (((n) & 255) << 16)
+#define ULPI_DATA(n)          ((n) & 255)
+#define ULPI_DATA_READ(n)     (((n) >> 8) & 255)
+
+#define ASYNC_INTR_CTRL         (1 << 29) /* Enable async interrupt */
+#define ULPI_STP_CTRL           (1 << 30) /* Block communication with PHY */
+
+/* OTG definitions */
+#define OTGSC_INTSTS_MASK	(0x7f << 16)
+#define OTGSC_ID		(1 << 8)
+#define OTGSC_BSV		(1 << 11)
+#define OTGSC_IDIS		(1 << 16)
+#define OTGSC_BSVIS		(1 << 19)
+#define OTGSC_IDIE		(1 << 24)
+#define OTGSC_BSVIE		(1 << 27)
+
+#endif /* __LINUX_USB_GADGET_MSM72K_UDC_H__ */
diff --git a/include/linux/usb/musb.h b/include/linux/usb/musb.h
index 2387f9fc813..eb505250940 100644
--- a/include/linux/usb/musb.h
+++ b/include/linux/usb/musb.h
@@ -3,7 +3,7 @@
  * Inventra (Multidrop) Highspeed Dual-Role Controllers:  (M)HDRC.
  *
  * Board initialization should put one of these into dev->platform_data,
- * probably on some platform_device named "musb_hdrc".  It encapsulates
+ * probably on some platform_device named "musb-hdrc".  It encapsulates
  * key configuration differences between boards.
  */
 
@@ -120,14 +120,14 @@ struct musb_hdrc_platform_data {
 	/* Power the device on or off */
 	int		(*set_power)(int state);
 
-	/* Turn device clock on or off */
-	int		(*set_clock)(struct clk *clock, int is_on);
-
 	/* MUSB configuration-specific details */
 	struct musb_hdrc_config	*config;
 
 	/* Architecture specific board data	*/
 	void		*board_data;
+
+	/* Platform specific struct musb_ops pointer */
+	const void	*platform_ops;
 };
 
 
diff --git a/include/linux/usb/otg.h b/include/linux/usb/otg.h
index 0a5b3711e50..a1a1e7a73ec 100644
--- a/include/linux/usb/otg.h
+++ b/include/linux/usb/otg.h
@@ -116,7 +116,7 @@ struct otg_transceiver {
 /* for board-specific init logic */
 extern int otg_set_transceiver(struct otg_transceiver *);
 
-#if defined(CONFIG_NOP_USB_XCEIV) || defined(CONFIG_NOP_USB_XCEIV_MODULE)
+#if defined(CONFIG_NOP_USB_XCEIV) || (defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE))
 /* sometimes transceivers are accessed only through e.g. ULPI */
 extern void usb_nop_xceiv_register(void);
 extern void usb_nop_xceiv_unregister(void);