diff options
| author | Andy Walls <awalls@md.metrocast.net> | 2010-07-18 18:51:10 -0300 |
|---|---|---|
| committer | Mauro Carvalho Chehab <mchehab@redhat.com> | 2010-08-08 23:42:54 -0300 |
| commit | 66752f8396f97360cafb226aa1fe230f66785c5a (patch) | |
| tree | c00862b068ae1f21897538e8451bfdd97751a45d /include/media | |
| parent | e9e5cf472751a16ebe80c9a47b512605e3511880 (diff) | |
V4L/DVB: v4l2_subdev: Add s_io_pin_config to v4l2_subdev_core_ops
Add a method to v4l2_sudev_core_ops to allow bridge drivers to
manage what signal pads/functions are routed out to multiplexed IO pins on a
pin by pin basis. The interface also allows specifying initial output settings
for pins and disabling an IO pin altogether.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Diffstat (limited to 'include/media')
| -rw-r--r-- | include/media/v4l2-subdev.h | 23 |
1 files changed, 23 insertions, 0 deletions
diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h index 02c6f4d11ed..9195ad490ee 100644 --- a/include/media/v4l2-subdev.h +++ b/include/media/v4l2-subdev.h @@ -90,10 +90,31 @@ struct v4l2_decode_vbi_line { not yet implemented) since ops provide proper type-checking. */ +/* Subdevice external IO pin configuration */ +#define V4L2_SUBDEV_IO_PIN_DISABLE (1 << 0) /* ENABLE assumed */ +#define V4L2_SUBDEV_IO_PIN_OUTPUT (1 << 1) +#define V4L2_SUBDEV_IO_PIN_INPUT (1 << 2) +#define V4L2_SUBDEV_IO_PIN_SET_VALUE (1 << 3) /* Set output value */ +#define V4L2_SUBDEV_IO_PIN_ACTIVE_LOW (1 << 4) /* ACTIVE HIGH assumed */ + +struct v4l2_subdev_io_pin_config { + u32 flags; /* V4L2_SUBDEV_IO_PIN_* flags for this pin's config */ + u8 pin; /* Chip external IO pin to configure */ + u8 function; /* Internal signal pad/function to route to IO pin */ + u8 value; /* Initial value for pin - e.g. GPIO output value */ + u8 strength; /* Pin drive strength */ +}; + /* s_config: if set, then it is always called by the v4l2_i2c_new_subdev* functions after the v4l2_subdev was registered. It is used to pass platform data to the subdev which can be used during initialization. + s_io_pin_config: configure one or more chip I/O pins for chips that + multiplex different internal signal pads out to IO pins. This function + takes a pointer to an array of 'n' pin configuration entries, one for + each pin being configured. This function could be called at times + other than just subdevice initialization. + init: initialize the sensor registors to some sort of reasonable default values. Do not use for new drivers and should be removed in existing drivers. @@ -115,6 +136,8 @@ struct v4l2_subdev_core_ops { int (*g_chip_ident)(struct v4l2_subdev *sd, struct v4l2_dbg_chip_ident *chip); int (*log_status)(struct v4l2_subdev *sd); int (*s_config)(struct v4l2_subdev *sd, int irq, void *platform_data); + int (*s_io_pin_config)(struct v4l2_subdev *sd, size_t n, + struct v4l2_subdev_io_pin_config *pincfg); int (*init)(struct v4l2_subdev *sd, u32 val); int (*load_fw)(struct v4l2_subdev *sd); int (*reset)(struct v4l2_subdev *sd, u32 val); |