mfd: db8500 OPP and sleep handling update

This updates the operating point handling code by:

- Supporting the DDR OPP retention state.
- Supporting another low operating point named
  APE_50_PARTLY_25_OPP
- Adding an interface to figure out if the sleep state change
  was properly achieved.

Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

2 files changed, 38 insertions, 2 deletions

diff --git a/include/linux/mfd/db8500-prcmu.h b/include/linux/mfd/db8500-prcmu.h
index c5028f1246f..841342c5545 100644
--- a/include/linux/mfd/db8500-prcmu.h
+++ b/include/linux/mfd/db8500-prcmu.h
@@ -457,6 +457,25 @@ enum hw_acc_dev {
 	NUM_HW_ACC
 };
 
+/**
+ * enum prcmu_power_status - results from set_power_state
+ * @PRCMU_SLEEP_OK: Sleep went ok
+ * @PRCMU_DEEP_SLEEP_OK: DeepSleep went ok
+ * @PRCMU_IDLE_OK: Idle went ok
+ * @PRCMU_DEEPIDLE_OK: DeepIdle went ok
+ * @PRCMU_PRCMU2ARMPENDINGIT_ER: Pending interrupt detected
+ * @PRCMU_ARMPENDINGIT_ER: Pending interrupt detected
+ *
+ */
+enum prcmu_power_status {
+	PRCMU_SLEEP_OK			= 0xf3,
+	PRCMU_DEEP_SLEEP_OK		= 0xf6,
+	PRCMU_IDLE_OK			= 0xf0,
+	PRCMU_DEEPIDLE_OK		= 0xe3,
+	PRCMU_PRCMU2ARMPENDINGIT_ER	= 0x91,
+	PRCMU_ARMPENDINGIT_ER		= 0x93,
+};
+
 /*
  * Definitions for autonomous power management configuration.
  */
@@ -544,6 +563,7 @@ int db8500_prcmu_load_a9wdog(u8 id, u32 val);
 
 void db8500_prcmu_system_reset(u16 reset_code);
 int db8500_prcmu_set_power_state(u8 state, bool keep_ulp_clk, bool keep_ap_pll);
+u8 db8500_prcmu_get_power_state_result(void);
 void db8500_prcmu_enable_wakeups(u32 wakeups);
 int db8500_prcmu_set_epod(u16 epod_id, u8 epod_state);
 int db8500_prcmu_request_clock(u8 clock, bool enable);
@@ -699,6 +719,11 @@ static inline int db8500_prcmu_set_power_state(u8 state, bool keep_ulp_clk,
 	return 0;
 }
 
+static inline u8 db8500_prcmu_get_power_state_result(void)
+{
+	return 0;
+}
+
 static inline void db8500_prcmu_enable_wakeups(u32 wakeups) {}
 
 static inline int db8500_prcmu_set_epod(u16 epod_id, u8 epod_state)
diff --git a/include/linux/mfd/dbx500-prcmu.h b/include/linux/mfd/dbx500-prcmu.h
index 8470c7d7121..432a2d3fc19 100644
--- a/include/linux/mfd/dbx500-prcmu.h
+++ b/include/linux/mfd/dbx500-prcmu.h
@@ -185,12 +185,14 @@ enum prcmu_clock {
  * @APE_NO_CHANGE: The APE operating point is unchanged
  * @APE_100_OPP: The new APE operating point is ape100opp
  * @APE_50_OPP: 50%
+ * @APE_50_PARTLY_25_OPP: 50%, except some clocks at 25%.
  */
 enum ape_opp {
 	APE_OPP_INIT = 0x00,
 	APE_NO_CHANGE = 0x01,
 	APE_100_OPP = 0x02,
-	APE_50_OPP = 0x03
+	APE_50_OPP = 0x03,
+	APE_50_PARTLY_25_OPP = 0xFF,
 };
 
 /**
@@ -271,6 +273,14 @@ static inline int prcmu_set_power_state(u8 state, bool keep_ulp_clk,
 			keep_ap_pll);
 }
 
+static inline u8 prcmu_get_power_state_result(void)
+{
+	if (cpu_is_u5500())
+		return -EINVAL;
+	else
+		return db8500_prcmu_get_power_state_result();
+}
+
 static inline int prcmu_set_epod(u16 epod_id, u8 epod_state)
 {
 	if (cpu_is_u5500())
@@ -663,9 +673,10 @@ static inline int prcmu_stop_temp_sense(void)
 /* PRCMU QoS APE OPP class */
 #define PRCMU_QOS_APE_OPP 1
 #define PRCMU_QOS_DDR_OPP 2
+#define PRCMU_QOS_ARM_OPP 3
 #define PRCMU_QOS_DEFAULT_VALUE -1
 
-#ifdef CONFIG_UX500_PRCMU_QOS_POWER
+#ifdef CONFIG_DBX500_PRCMU_QOS_POWER
 
 unsigned long prcmu_qos_get_cpufreq_opp_delay(void);
 void prcmu_qos_set_cpufreq_opp_delay(unsigned long);