Merge tag 'mmc-v3.16-1' of git://git.linaro.org/people/ulf.hansson/mmc into next

Pull MMC update from Ulf Hansson:
 "These patches are mainly updates for the mmci driver and have been
  tested in linux-next.

  Some ARM SoC related patches are also included and those have been
  acked from the corresponding maintainers to go through my mmc tree.

  Updates for mmci driver:
   - Put the device into low power state at system suspend.
   - Convert to the common mmc DT parser.
   - Add missing DT bindings needed for ux500.

  Updates for ARM ux500|u300:
   - Convert to the common mmc DT bindings.
   - Remove redundant board file for mmci platform data"

* tag 'mmc-v3.16-1' of git://git.linaro.org/people/ulf.hansson/mmc: (22 commits)
  mmc: mmci: Enforce DMA configuration through DT
  mmc: mmci: Enforce max frequency configuration through DT
  mmc: mmci: Enforce mmc capabilities through DT
  mmc: mmci: Enforce DT for signal direction and feedback clock
  ARM: ux500: Remove redundant board file for mmci platform data
  ARM: ux500: Add a vmmc regulator through DT for the poped eMMC for href
  ARM: ux500: Add the mmc capabilities flags to DT
  mmc: mmci: Enable MMC_CAP_CMD23
  mmc: mmci: Mark the DT bindings for highspeed mode as deprecated
  ARM: u300: Convert to the common mmc DT bindings for highspeed mode
  ARM: nomadik: Convert to the common mmc DT bindings for highspeed mode
  ARM: ux500: Convert to the common mmc DT bindings for highspeed mode
  ARM: ux500: Add mmci signal directions and feeback clock in DT for href
  mmc: mmci: Use the common mmc DT parser
  mmc: mmci: Add DT bindings for feedback clock pin
  mmc: mmci: Add DT bindings for signal direction
  mmc: mmci: Update DT documentation
  mmc: mmci: Convert to devm functions
  mmc: mmci: Convert to the mmc gpio API
  mmc: mmci: Put the device into low power state at system suspend
  ...

1 files changed, 0 insertions, 42 deletions

diff --git a/include/linux/amba/mmci.h b/include/linux/amba/mmci.h
index 32a89cf5ec4..8c98113069c 100644
--- a/include/linux/amba/mmci.h
+++ b/include/linux/amba/mmci.h
@@ -6,28 +6,9 @@
 
 #include <linux/mmc/host.h>
 
-
-/*
- * These defines is places here due to access is needed from machine
- * configuration files. The ST Micro version does not have ROD and
- * reuse the voltage registers for direction settings.
- */
-#define MCI_ST_DATA2DIREN	(1 << 2)
-#define MCI_ST_CMDDIREN		(1 << 3)
-#define MCI_ST_DATA0DIREN	(1 << 4)
-#define MCI_ST_DATA31DIREN	(1 << 5)
-#define MCI_ST_FBCLKEN		(1 << 7)
-#define MCI_ST_DATA74DIREN	(1 << 8)
-
-/* Just some dummy forwarding */
-struct dma_chan;
-
 /**
  * struct mmci_platform_data - platform configuration for the MMCI
  * (also known as PL180) block.
- * @f_max: the maximum operational frequency for this host in this
- * platform configuration. When this is specified it takes precedence
- * over the module parameter for the same frequency.
  * @ocr_mask: available voltages on the 4 pins from the block, this
  * is ignored if a regulator is used, see the MMC_VDD_* masks in
  * mmc/host.h
@@ -42,37 +23,14 @@ struct dma_chan;
  * @gpio_wp: read this GPIO pin to see if the card is write protected
  * @gpio_cd: read this GPIO pin to detect card insertion
  * @cd_invert: true if the gpio_cd pin value is active low
- * @capabilities: the capabilities of the block as implemented in
- * this platform, signify anything MMC_CAP_* from mmc/host.h
- * @capabilities2: more capabilities, MMC_CAP2_* from mmc/host.h
- * @sigdir: a bit field indicating for what bits in the MMC bus the host
- * should enable signal direction indication.
- * @dma_filter: function used to select an appropriate RX and TX
- * DMA channel to be used for DMA, if and only if you're deploying the
- * generic DMA engine
- * @dma_rx_param: parameter passed to the DMA allocation
- * filter in order to select an appropriate RX channel. If
- * there is a bidirectional RX+TX channel, then just specify
- * this and leave dma_tx_param set to NULL
- * @dma_tx_param: parameter passed to the DMA allocation
- * filter in order to select an appropriate TX channel. If this
- * is NULL the driver will attempt to use the RX channel as a
- * bidirectional channel
  */
 struct mmci_platform_data {
-	unsigned int f_max;
 	unsigned int ocr_mask;
 	int (*ios_handler)(struct device *, struct mmc_ios *);
 	unsigned int (*status)(struct device *);
 	int	gpio_wp;
 	int	gpio_cd;
 	bool	cd_invert;
-	unsigned long capabilities;
-	unsigned long capabilities2;
-	u32 sigdir;
-	bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
-	void *dma_rx_param;
-	void *dma_tx_param;
 };
 
 #endif