diff options
-rw-r--r-- | drivers/ata/sata_inic162x.c | 49 |
1 files changed, 15 insertions, 34 deletions
diff --git a/drivers/ata/sata_inic162x.c b/drivers/ata/sata_inic162x.c index 3ca0ee93bc1..579154c2790 100644 --- a/drivers/ata/sata_inic162x.c +++ b/drivers/ata/sata_inic162x.c @@ -356,12 +356,12 @@ static void inic_host_intr(struct ata_port *ap) if (unlikely((irq_stat & PIRQ_ERR) || (idma_stat & IDMA_STAT_ERR))) inic_host_err_intr(ap, irq_stat, idma_stat); - if (unlikely(!qc || (qc->tf.flags & ATA_TFLAG_POLLING))) { + if (unlikely(!qc)) { ap->ops->sff_check_status(ap); /* clear ATA interrupt */ goto spurious; } - if (qc->tf.protocol == ATA_PROT_DMA) { + if (!ata_is_atapi(qc->tf.protocol)) { if (likely(idma_stat & IDMA_STAT_DONE)) { inic_stop_idma(ap); @@ -425,11 +425,14 @@ static void inic_fill_sg(struct inic_prd *prd, struct ata_queued_cmd *qc) { struct scatterlist *sg; unsigned int si; - u8 flags = PRD_DMA; + u8 flags = 0; if (qc->tf.flags & ATA_TFLAG_WRITE) flags |= PRD_WRITE; + if (ata_is_dma(qc->tf.protocol)) + flags |= PRD_DMA; + for_each_sg(qc->sg, sg, qc->n_elem, si) { prd->mad = cpu_to_le32(sg_dma_address(sg)); prd->len = cpu_to_le16(sg_dma_len(sg)); @@ -447,16 +450,20 @@ static void inic_qc_prep(struct ata_queued_cmd *qc) struct inic_pkt *pkt = pp->pkt; struct inic_cpb *cpb = &pkt->cpb; struct inic_prd *prd = pkt->prd; + bool is_atapi = ata_is_atapi(qc->tf.protocol); + bool is_data = ata_is_data(qc->tf.protocol); VPRINTK("ENTER\n"); - if (qc->tf.protocol != ATA_PROT_DMA) + if (is_atapi) return; /* prepare packet, based on initio driver */ memset(pkt, 0, sizeof(struct inic_pkt)); - cpb->ctl_flags = CPB_CTL_VALID | CPB_CTL_IEN | CPB_CTL_DATA; + cpb->ctl_flags = CPB_CTL_VALID | CPB_CTL_IEN; + if (is_data) + cpb->ctl_flags |= CPB_CTL_DATA; cpb->len = cpu_to_le32(qc->nbytes); cpb->prd = cpu_to_le32(pp->pkt_dma + offsetof(struct inic_pkt, prd)); @@ -480,7 +487,8 @@ static void inic_qc_prep(struct ata_queued_cmd *qc) /* don't load ctl - dunno why. it's like that in the initio driver */ /* setup sg table */ - inic_fill_sg(prd, qc); + if (is_data) + inic_fill_sg(prd, qc); pp->cpb_tbl[0] = pp->pkt_dma; } @@ -490,7 +498,7 @@ static unsigned int inic_qc_issue(struct ata_queued_cmd *qc) struct ata_port *ap = qc->ap; void __iomem *port_base = inic_port_base(ap); - if (qc->tf.protocol == ATA_PROT_DMA) { + if (!ata_is_atapi(qc->tf.protocol)) { /* fire up the ADMA engine */ writew(HCTL_FTHD0, port_base + HOST_CTL); writew(IDMA_CTL_GO, port_base + PORT_IDMA_CTL); @@ -499,18 +507,6 @@ static unsigned int inic_qc_issue(struct ata_queued_cmd *qc) return 0; } - /* Issuing a command to yet uninitialized port locks up the - * controller. Most of the time, this happens for the first - * command after reset which are ATA and ATAPI IDENTIFYs. - * Fast fail if stat is 0x7f or 0xff for those commands. - */ - if (unlikely(qc->tf.command == ATA_CMD_ID_ATA || - qc->tf.command == ATA_CMD_ID_ATAPI)) { - u8 stat = ap->ops->sff_check_status(ap); - if (stat == 0x7f || stat == 0xff) - return AC_ERR_HSM; - } - return ata_sff_qc_issue(qc); } @@ -647,20 +643,6 @@ static void inic_post_internal_cmd(struct ata_queued_cmd *qc) inic_reset_port(inic_port_base(qc->ap)); } -static void inic_dev_config(struct ata_device *dev) -{ - /* inic can only handle upto LBA28 max sectors */ - if (dev->max_sectors > ATA_MAX_SECTORS) - dev->max_sectors = ATA_MAX_SECTORS; - - if (dev->n_sectors >= 1 << 28) { - ata_dev_printk(dev, KERN_ERR, - "ERROR: This driver doesn't support LBA48 yet and may cause\n" - " data corruption on such devices. Disabling.\n"); - ata_dev_disable(dev); - } -} - static void init_port(struct ata_port *ap) { void __iomem *port_base = inic_port_base(ap); @@ -726,7 +708,6 @@ static struct ata_port_operations inic_port_ops = { .hardreset = inic_hardreset, .error_handler = inic_error_handler, .post_internal_cmd = inic_post_internal_cmd, - .dev_config = inic_dev_config, .scr_read = inic_scr_read, .scr_write = inic_scr_write, |