diff options
53 files changed, 996 insertions, 360 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index a96e85397eb..ac1be25c1e2 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -52,6 +52,7 @@ Table of Contents i) Freescale QUICC Engine module (QE) j) CFI or JEDEC memory-mapped NOR flash k) Global Utilities Block + l) Xilinx IP cores VII - Specifying interrupt information for devices 1) interrupts property @@ -851,12 +852,18 @@ address which can extend beyond that limit. /cpus/PowerPC,970FX@0 /cpus/PowerPC,970FX@1 (unit addresses do not require leading zeroes) - - d-cache-line-size : one cell, L1 data cache line size in bytes - - i-cache-line-size : one cell, L1 instruction cache line size in + - d-cache-block-size : one cell, L1 data cache block size in bytes (*) + - i-cache-block-size : one cell, L1 instruction cache block size in bytes - d-cache-size : one cell, size of L1 data cache in bytes - i-cache-size : one cell, size of L1 instruction cache in bytes +(*) The cache "block" size is the size on which the cache management +instructions operate. Historically, this document used the cache +"line" size here which is incorrect. The kernel will prefer the cache +block size and will fallback to cache line size for backward +compatibility. + Recommended properties: - timebase-frequency : a cell indicating the frequency of the @@ -870,6 +877,10 @@ address which can extend beyond that limit. for the above, the common code doesn't use that property, but you are welcome to re-use the pSeries or Maple one. A future kernel version might provide a common function for this. + - d-cache-line-size : one cell, L1 data cache line size in bytes + if different from the block size + - i-cache-line-size : one cell, L1 instruction cache line size in + bytes if different from the block size You are welcome to add any property you find relevant to your board, like some information about the mechanism used to soft-reset the @@ -2242,6 +2253,266 @@ platforms are moved over to use the flattened-device-tree model. available. For Axon: 0x0000012a + l) Xilinx IP cores + + The Xilinx EDK toolchain ships with a set of IP cores (devices) for use + in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range + of standard device types (network, serial, etc.) and miscellanious + devices (gpio, LCD, spi, etc). Also, since these devices are + implemented within the fpga fabric every instance of the device can be + synthesised with different options that change the behaviour. + + Each IP-core has a set of parameters which the FPGA designer can use to + control how the core is synthesized. Historically, the EDK tool would + extract the device parameters relevant to device drivers and copy them + into an 'xparameters.h' in the form of #define symbols. This tells the + device drivers how the IP cores are configured, but it requres the kernel + to be recompiled every time the FPGA bitstream is resynthesized. + + The new approach is to export the parameters into the device tree and + generate a new device tree each time the FPGA bitstream changes. The + parameters which used to be exported as #defines will now become + properties of the device node. In general, device nodes for IP-cores + will take the following form: + + (name)@(base-address) { + compatible = "xlnx,(ip-core-name)-(HW_VER)" + [, (list of compatible devices), ...]; + reg = <(baseaddr) (size)>; + interrupt-parent = <&interrupt-controller-phandle>; + interrupts = < ... >; + xlnx,(parameter1) = "(string-value)"; + xlnx,(parameter2) = <(int-value)>; + }; + + (ip-core-name): the name of the ip block (given after the BEGIN + directive in system.mhs). Should be in lowercase + and all underscores '_' converted to dashes '-'. + (name): is derived from the "PARAMETER INSTANCE" value. + (parameter#): C_* parameters from system.mhs. The C_ prefix is + dropped from the parameter name, the name is converted + to lowercase and all underscore '_' characters are + converted to dashes '-'. + (baseaddr): the C_BASEADDR parameter. + (HW_VER): from the HW_VER parameter. + (size): equals C_HIGHADDR - C_BASEADDR + 1 + + Typically, the compatible list will include the exact IP core version + followed by an older IP core version which implements the same + interface or any other device with the same interface. + + 'reg', 'interrupt-parent' and 'interrupts' are all optional properties. + + For example, the following block from system.mhs: + + BEGIN opb_uartlite + PARAMETER INSTANCE = opb_uartlite_0 + PARAMETER HW_VER = 1.00.b + PARAMETER C_BAUDRATE = 115200 + PARAMETER C_DATA_BITS = 8 + PARAMETER C_ODD_PARITY = 0 + PARAMETER C_USE_PARITY = 0 + PARAMETER C_CLK_FREQ = 50000000 + PARAMETER C_BASEADDR = 0xEC100000 + PARAMETER C_HIGHADDR = 0xEC10FFFF + BUS_INTERFACE SOPB = opb_7 + PORT OPB_Clk = CLK_50MHz + PORT Interrupt = opb_uartlite_0_Interrupt + PORT RX = opb_uartlite_0_RX + PORT TX = opb_uartlite_0_TX + PORT OPB_Rst = sys_bus_reset_0 + END + + becomes the following device tree node: + + opb-uartlite-0@ec100000 { + device_type = "serial"; + compatible = "xlnx,opb-uartlite-1.00.b"; + reg = <ec100000 10000>; + interrupt-parent = <&opb-intc>; + interrupts = <1 0>; // got this from the opb_intc parameters + current-speed = <d#115200>; // standard serial device prop + clock-frequency = <d#50000000>; // standard serial device prop + xlnx,data-bits = <8>; + xlnx,odd-parity = <0>; + xlnx,use-parity = <0>; + }; + + Some IP cores actually implement 2 or more logical devices. In this case, + the device should still describe the whole IP core with a single node + and add a child node for each logical device. The ranges property can + be used to translate from parent IP-core to the registers of each device. + (Note: this makes the assumption that both logical devices have the same + bus binding. If this is not true, then separate nodes should be used for + each logical device). The 'cell-index' property can be used to enumerate + logical devices within an IP core. For example, the following is the + system.mhs entry for the dual ps2 controller found on the ml403 reference + design. + + BEGIN opb_ps2_dual_ref + PARAMETER INSTANCE = opb_ps2_dual_ref_0 + PARAMETER HW_VER = 1.00.a + PARAMETER C_BASEADDR = 0xA9000000 + PARAMETER C_HIGHADDR = 0xA9001FFF + BUS_INTERFACE SOPB = opb_v20_0 + PORT Sys_Intr1 = ps2_1_intr + PORT Sys_Intr2 = ps2_2_intr + PORT Clkin1 = ps2_clk_rx_1 + PORT Clkin2 = ps2_clk_rx_2 + PORT Clkpd1 = ps2_clk_tx_1 + PORT Clkpd2 = ps2_clk_tx_2 + PORT Rx1 = ps2_d_rx_1 + PORT Rx2 = ps2_d_rx_2 + PORT Txpd1 = ps2_d_tx_1 + PORT Txpd2 = ps2_d_tx_2 + END + + It would result in the following device tree nodes: + + opb_ps2_dual_ref_0@a9000000 { + ranges = <0 a9000000 2000>; + // If this device had extra parameters, then they would + // go here. + ps2@0 { + compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; + reg = <0 40>; + interrupt-parent = <&opb-intc>; + interrupts = <3 0>; + cell-index = <0>; + }; + ps2@1000 { + compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; + reg = <1000 40>; + interrupt-parent = <&opb-intc>; + interrupts = <3 0>; + cell-index = <0>; + }; + }; + + Also, the system.mhs file defines bus attachments from the processor + to the devices. The device tree structure should reflect the bus + attachments. Again an example; this system.mhs fragment: + + BEGIN ppc405_virtex4 + PARAMETER INSTANCE = ppc405_0 + PARAMETER HW_VER = 1.01.a + BUS_INTERFACE DPLB = plb_v34_0 + BUS_INTERFACE IPLB = plb_v34_0 + END + + BEGIN opb_intc + PARAMETER INSTANCE = opb_intc_0 + PARAMETER HW_VER = 1.00.c + PARAMETER C_BASEADDR = 0xD1000FC0 + PARAMETER C_HIGHADDR = 0xD1000FDF + BUS_INTERFACE SOPB = opb_v20_0 + END + + BEGIN opb_uart16550 + PARAMETER INSTANCE = opb_uart16550_0 + PARAMETER HW_VER = 1.00.d + PARAMETER C_BASEADDR = 0xa0000000 + PARAMETER C_HIGHADDR = 0xa0001FFF + BUS_INTERFACE SOPB = opb_v20_0 + END + + BEGIN plb_v34 + PARAMETER INSTANCE = plb_v34_0 + PARAMETER HW_VER = 1.02.a + END + + BEGIN plb_bram_if_cntlr + PARAMETER INSTANCE = plb_bram_if_cntlr_0 + PARAMETER HW_VER = 1.00.b + PARAMETER C_BASEADDR = 0xFFFF0000 + PARAMETER C_HIGHADDR = 0xFFFFFFFF + BUS_INTERFACE SPLB = plb_v34_0 + END + + BEGIN plb2opb_bridge + PARAMETER INSTANCE = plb2opb_bridge_0 + PARAMETER HW_VER = 1.01.a + PARAMETER C_RNG0_BASEADDR = 0x20000000 + PARAMETER C_RNG0_HIGHADDR = 0x3FFFFFFF + PARAMETER C_RNG1_BASEADDR = 0x60000000 + PARAMETER C_RNG1_HIGHADDR = 0x7FFFFFFF + PARAMETER C_RNG2_BASEADDR = 0x80000000 + PARAMETER C_RNG2_HIGHADDR = 0xBFFFFFFF + PARAMETER C_RNG3_BASEADDR = 0xC0000000 + PARAMETER C_RNG3_HIGHADDR = 0xDFFFFFFF + BUS_INTERFACE SPLB = plb_v34_0 + BUS_INTERFACE MOPB = opb_v20_0 + END + + Gives this device tree (some properties removed for clarity): + + plb-v34-0 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "ibm,plb"; + ranges; // 1:1 translation + + plb-bram-if-cntrl-0@ffff0000 { + reg = <ffff0000 10000>; + } + + opb-v20-0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <20000000 20000000 20000000 + 60000000 60000000 20000000 + 80000000 80000000 40000000 + c0000000 c0000000 20000000>; + + opb-uart16550-0@a0000000 { + reg = <a00000000 2000>; + }; + + opb-intc-0@d1000fc0 { + reg = <d1000fc0 20>; + }; + }; + }; + + That covers the general approach to binding xilinx IP cores into the + device tree. The following are bindings for specific devices: + + i) Xilinx ML300 Framebuffer + + Simple framebuffer device from the ML300 reference design (also on the + ML403 reference design as well as others). + + Optional properties: + - resolution = <xres yres> : pixel resolution of framebuffer. Some + implementations use a different resolution. + Default is <d#640 d#480> + - virt-resolution = <xvirt yvirt> : Size of framebuffer in memory. + Default is <d#1024 d#480>. + - rotate-display (empty) : rotate display 180 degrees. + + ii) Xilinx SystemACE + + The Xilinx SystemACE device is used to program FPGAs from an FPGA + bitstream stored on a CF card. It can also be used as a generic CF + interface device. + + Optional properties: + - 8-bit (empty) : Set this property for SystemACE in 8 bit mode + + iii) Xilinx EMAC and Xilinx TEMAC + + Xilinx Ethernet devices. In addition to general xilinx properties + listed above, nodes for these devices should include a phy-handle + property, and may include other common network device properties + like local-mac-address. + + iv) Xilinx Uartlite + + Xilinx uartlite devices are simple fixed speed serial ports. + + Requred properties: + - current-speed : Baud rate of uartlite + More devices will be defined as this spec matures. VII - Specifying interrupt information for devices diff --git a/arch/powerpc/boot/dts/walnut.dts b/arch/powerpc/boot/dts/walnut.dts index fa681f5343f..754fa3960f8 100644 --- a/arch/powerpc/boot/dts/walnut.dts +++ b/arch/powerpc/boot/dts/walnut.dts @@ -122,7 +122,9 @@ device_type = "network"; compatible = "ibm,emac-405gp", "ibm,emac"; interrupt-parent = <&UIC0>; - interrupts = <9 4 f 4>; + interrupts = < + f 4 /* Ethernet */ + 9 4 /* Ethernet Wake Up */>; local-mac-address = [000000000000]; /* Filled in by zImage */ reg = <ef600800 70>; mal-device = <&MAL>; diff --git a/arch/powerpc/boot/wrapper b/arch/powerpc/boot/wrapper index 39b27e5ef6c..31147a03772 100755 --- a/arch/powerpc/boot/wrapper +++ b/arch/powerpc/boot/wrapper @@ -21,6 +21,14 @@ # (default ./arch/powerpc/boot) # -W dir specify working directory for temporary files (default .) +# Stop execution if any command fails +set -e + +# Allow for verbose output +if [ "$V" = 1 ]; then + set -x +fi + # defaults kernel= ofile=zImage @@ -111,7 +119,7 @@ if [ -n "$dts" ]; then if [ -z "$dtb" ]; then dtb="$platform.dtb" fi - dtc -O dtb -o "$dtb" -b 0 -V 16 "$dts" || exit 1 + dtc -O dtb -o "$dtb" -b 0 -V 16 "$dts" fi if [ -z "$kernel" ]; then @@ -149,7 +157,6 @@ cuboot*) ps3) platformo="$object/ps3-head.o $object/ps3-hvcall.o $object/ps3.o" lds=$object/zImage.ps3.lds - binary=y gzip= ext=bin objflags="-O binary --set-section-flags=.bss=contents,alloc,load,data" @@ -233,7 +240,7 @@ entry=`${CROSS}objdump -f "$ofile" | grep '^start address ' | cut -d' ' -f3` if [ -n "$binary" ]; then mv "$ofile" "$ofile".elf - ${CROSS}objcopy -O binary "$ofile".elf "$ofile".bin + ${CROSS}objcopy -O binary "$ofile".elf "$ofile" fi # post-processing needed for some platforms @@ -246,9 +253,9 @@ coff) $object/hack-coff "$ofile" ;; cuboot*) - gzip -f -9 "$ofile".bin + gzip -f -9 "$ofile" mkimage -A ppc -O linux -T kernel -C gzip -a "$base" -e "$entry" \ - $uboot_version -d "$ofile".bin.gz "$ofile" + $uboot_version -d "$ofile".gz "$ofile" ;; treeboot*) mv "$ofile" "$ofile.elf" @@ -269,11 +276,11 @@ ps3) # then copied to offset 0x100. At runtime the bootwrapper program # copies the 0x100 bytes at __system_reset_kernel to addr 0x100. - system_reset_overlay=0x`${CROSS}nm "$ofile".elf \ + system_reset_overlay=0x`${CROSS}nm "$ofile" \ | grep ' __system_reset_overlay$' \ | cut -d' ' -f1` system_reset_overlay=`printf "%d" $system_reset_overlay` - system_reset_kernel=0x`${CROSS}nm "$ofile".elf \ + system_reset_kernel=0x`${CROSS}nm "$ofile" \ | grep ' __system_reset_kernel$' \ | cut -d' ' -f1` system_reset_kernel=`printf "%d" $system_reset_kernel` @@ -282,23 +289,15 @@ ps3) rm -f "$object/otheros.bld" - msg=$(dd if="$ofile.bin" of="$ofile.bin" conv=notrunc \ - skip=$overlay_dest seek=$system_reset_kernel \ - count=$overlay_size bs=1 2>&1) + ${CROSS}objcopy -O binary "$ofile" "$ofile.bin" - if [ $? -ne "0" ]; then - echo $msg - exit 1 - fi - - msg=$(dd if="$ofile.bin" of="$ofile.bin" conv=notrunc \ - skip=$system_reset_overlay seek=$overlay_dest \ - count=$overlay_size bs=1 2>&1) + dd if="$ofile.bin" of="$ofile.bin" conv=notrunc \ + skip=$overlay_dest seek=$system_reset_kernel \ + count=$overlay_size bs=1 - if [ $? -ne "0" ]; then - echo $msg - exit 2 - fi + dd if="$ofile.bin" of="$ofile.bin" conv=notrunc \ + skip=$system_reset_overlay seek=$overlay_dest \ + count=$overlay_size bs=1 gzip --force -9 --stdout "$ofile.bin" > "$object/otheros.bld" ;; diff --git a/arch/powerpc/configs/pasemi_defconfig b/arch/powerpc/configs/pasemi_defconfig index 1ccf3ed7693..78c968aade4 100644 --- a/arch/powerpc/configs/pasemi_defconfig +++ b/arch/powerpc/configs/pasemi_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Thu Aug 30 16:40:47 2007 +# Linux kernel version: 2.6.24-rc2 +# Tue Nov 6 23:23:50 2007 # CONFIG_PPC64=y @@ -10,6 +10,7 @@ CONFIG_PPC64=y # CONFIG_POWER4_ONLY=y CONFIG_POWER4=y +# CONFIG_TUNE_CELL is not set CONFIG_PPC_FPU=y CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y @@ -18,8 +19,13 @@ CONFIG_PPC_MM_SLICES=y CONFIG_SMP=y CONFIG_NR_CPUS=2 CONFIG_64BIT=y +CONFIG_WORD_SIZE=64 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -65,7 +71,10 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=17 -# CONFIG_CPUSETS is not set +# CONFIG_CGROUPS is not set +CONFIG_FAIR_GROUP_SCHED=y +CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -86,7 +95,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -107,14 +115,15 @@ CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_BLK_DEV_BSG is not set +CONFIG_BLOCK_COMPAT=y # # IO Schedulers # CONFIG_IOSCHED_NOOP=y CONFIG_IOSCHED_AS=y -# CONFIG_IOSCHED_DEADLINE is not set -# CONFIG_IOSCHED_CFQ is not set +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_DEADLINE is not set # CONFIG_DEFAULT_CFQ is not set @@ -125,7 +134,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -141,6 +149,7 @@ CONFIG_PPC_PASEMI=y # PA Semi PWRficient options # CONFIG_PPC_PASEMI_IOMMU=y +# CONFIG_PPC_PASEMI_IOMMU_DMA_FORCE is not set CONFIG_PPC_PASEMI_MDIO=y CONFIG_ELECTRA_IDE=y # CONFIG_PPC_CELLEB is not set @@ -156,29 +165,52 @@ CONFIG_MPIC=y # CONFIG_U3_DART is not set # CONFIG_PPC_RTAS is not set # CONFIG_MMIO_NVRAM is not set +CONFIG_MPIC_BROKEN_REGREAD=y # CONFIG_PPC_MPC106 is not set # CONFIG_PPC_970_NAP is not set # CONFIG_PPC_INDIRECT_IO is not set # CONFIG_GENERIC_IOMAP is not set -# CONFIG_CPU_FREQ is not set +CONFIG_CPU_FREQ=y +CONFIG_CPU_FREQ_TABLE=y +CONFIG_CPU_FREQ_DEBUG=y +CONFIG_CPU_FREQ_STAT=y +# CONFIG_CPU_FREQ_STAT_DETAILS is not set +CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y +# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set +CONFIG_CPU_FREQ_GOV_PERFORMANCE=y +CONFIG_CPU_FREQ_GOV_POWERSAVE=y +CONFIG_CPU_FREQ_GOV_USERSPACE=y +CONFIG_CPU_FREQ_GOV_ONDEMAND=y +# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set + +# +# CPU Frequency drivers +# +CONFIG_PPC_PASEMI_CPUFREQ=y # CONFIG_CPM2 is not set # CONFIG_FSL_ULI1575 is not set # # Kernel options # -CONFIG_HZ_100=y +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_HZ_100 is not set # CONFIG_HZ_250 is not set # CONFIG_HZ_300 is not set -# CONFIG_HZ_1000 is not set -CONFIG_HZ=100 +CONFIG_HZ_1000=y +CONFIG_HZ=1000 CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set -CONFIG_PREEMPT_BKL=y +# CONFIG_PREEMPT_BKL is not set CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set -CONFIG_FORCE_MAX_ZONEORDER=13 +CONFIG_FORCE_MAX_ZONEORDER=9 CONFIG_IOMMU_VMERGE=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y # CONFIG_KEXEC is not set @@ -196,12 +228,13 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_RESOURCES_64BIT=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y -# CONFIG_PPC_HAS_HASH_64K is not set -# CONFIG_PPC_64K_PAGES is not set +CONFIG_PPC_HAS_HASH_64K=y +CONFIG_PPC_64K_PAGES=y # CONFIG_SCHED_SMT is not set CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set @@ -222,11 +255,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# CONFIG_PCCARD=y CONFIG_PCMCIA_DEBUG=y CONFIG_PCMCIA=y @@ -240,6 +270,7 @@ CONFIG_CARDBUS=y # CONFIG_YENTA is not set # CONFIG_PD6729 is not set # CONFIG_I82092 is not set +# CONFIG_ELECTRA_CF is not set # CONFIG_HOTPLUG_PCI is not set CONFIG_KERNEL_START=0xc000000000000000 @@ -255,7 +286,7 @@ CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y CONFIG_XFRM=y -# CONFIG_XFRM_USER is not set +CONFIG_XFRM_USER=y # CONFIG_XFRM_SUB_POLICY is not set # CONFIG_XFRM_MIGRATE is not set CONFIG_NET_KEY=y @@ -281,6 +312,7 @@ CONFIG_INET_TUNNEL=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +CONFIG_INET_LRO=y CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -306,10 +338,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -338,6 +366,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -361,6 +390,7 @@ CONFIG_MTD_BLOCK=y # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -385,6 +415,7 @@ CONFIG_MTD_CFI_I2=y # Mapping drivers for chip access # # CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_INTEL_VR_NOR is not set # CONFIG_MTD_PLATRAM is not set # @@ -402,7 +433,15 @@ CONFIG_MTD_PHRAM=y # CONFIG_MTD_DOC2000 is not set # CONFIG_MTD_DOC2001 is not set # CONFIG_MTD_DOC2001PLUS is not set -# CONFIG_MTD_NAND is not set +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_CAFE is not set +# CONFIG_MTD_NAND_PLATFORM is not set +# CONFIG_MTD_ALAUDA is not set # CONFIG_MTD_ONENAND is not set # @@ -455,10 +494,42 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # # CONFIG_IDE_GENERIC is not set -# CONFIG_BLK_DEV_IDEPCI is not set +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# # CONFIG_IDEPCI_PCIBUS_ORDER is not set +# CONFIG_BLK_DEV_GENERIC is not set +# CONFIG_BLK_DEV_OPTI621 is not set +# CONFIG_BLK_DEV_AEC62XX is not set +# CONFIG_BLK_DEV_ALI15X3 is not set +# CONFIG_BLK_DEV_AMD74XX is not set +# CONFIG_BLK_DEV_CMD64X is not set +# CONFIG_BLK_DEV_TRIFLEX is not set +# CONFIG_BLK_DEV_CY82C693 is not set +# CONFIG_BLK_DEV_CS5520 is not set +# CONFIG_BLK_DEV_CS5530 is not set +# CONFIG_BLK_DEV_HPT34X is not set +# CONFIG_BLK_DEV_HPT366 is not set +# CONFIG_BLK_DEV_JMICRON is not set +# CONFIG_BLK_DEV_SC1200 is not set +# CONFIG_BLK_DEV_PIIX is not set +# CONFIG_BLK_DEV_IT8213 is not set +# CONFIG_BLK_DEV_IT821X is not set +# CONFIG_BLK_DEV_NS87415 is not set +# CONFIG_BLK_DEV_PDC202XX_OLD is not set +# CONFIG_BLK_DEV_PDC202XX_NEW is not set +# CONFIG_BLK_DEV_SVWKS is not set +# CONFIG_BLK_DEV_SIIMAGE is not set +# CONFIG_BLK_DEV_SL82C105 is not set +# CONFIG_BLK_DEV_SLC90E66 is not set +# CONFIG_BLK_DEV_TRM290 is not set +# CONFIG_BLK_DEV_VIA82CXXX is not set +# CONFIG_BLK_DEV_TC86C001 is not set # CONFIG_IDE_ARM is not set # CONFIG_BLK_DEV_IDEDMA is not set +CONFIG_IDE_ARCH_OBSOLETE_INIT=y # CONFIG_BLK_DEV_HD is not set # @@ -498,10 +569,11 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set -CONFIG_BLK_DEV_3W_XXXX_RAID=y -CONFIG_SCSI_3W_9XXX=y +# CONFIG_BLK_DEV_3W_XXXX_RAID is not set +# CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set # CONFIG_SCSI_AACRAID is not set # CONFIG_SCSI_AIC7XXX is not set @@ -574,9 +646,10 @@ CONFIG_ATA_GENERIC=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set -# CONFIG_PATA_PCMCIA is not set +CONFIG_PATA_PCMCIA=y # CONFIG_PATA_PDC_OLD is not set # CONFIG_PATA_RADISYS is not set # CONFIG_PATA_RZ1000 is not set @@ -589,41 +662,13 @@ CONFIG_ATA_GENERIC=y # CONFIG_PATA_WINBOND is not set CONFIG_PATA_PLATFORM=y # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support # # CONFIG_FIREWIRE is not set -CONFIG_IEEE1394=y - -# -# Subsystem Options -# -# CONFIG_IEEE1394_VERBOSEDEBUG is not set - -# -# Controllers -# -CONFIG_IEEE1394_PCILYNX=y -CONFIG_IEEE1394_OHCI1394=y - -# -# Protocols -# -# CONFIG_IEEE1394_VIDEO1394 is not set -CONFIG_IEEE1394_SBP2=y -# CONFIG_IEEE1394_ETH1394_ROM_ENTRY is not set -# CONFIG_IEEE1394_ETH1394 is not set -# CONFIG_IEEE1394_DV1394 is not set -CONFIG_IEEE1394_RAWIO=y +# CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y @@ -633,6 +678,8 @@ CONFIG_DUMMY=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -649,6 +696,7 @@ CONFIG_MARVELL_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -657,13 +705,16 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set CONFIG_NET_PCI=y # CONFIG_PCNET32 is not set # CONFIG_AMD8111_ETH is not set # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set # CONFIG_E100 is not set # CONFIG_FEALNX is not set @@ -682,6 +733,7 @@ CONFIG_NETDEV_1000=y CONFIG_E1000=y CONFIG_E1000_NAPI=y # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -689,6 +741,7 @@ CONFIG_E1000_NAPI=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set CONFIG_TIGON3=y # CONFIG_BNX2 is not set @@ -697,12 +750,15 @@ CONFIG_TIGON3=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set CONFIG_PASEMI_MAC=y # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -749,7 +805,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 CONFIG_INPUT_JOYDEV=y -# CONFIG_INPUT_TSDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set @@ -810,15 +865,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=4 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set CONFIG_HW_RANDOM=y CONFIG_HW_RANDOM_PASEMI=y CONFIG_GEN_RTC=y CONFIG_GEN_RTC_X=y # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # # PCMCIA character devices @@ -896,8 +948,6 @@ CONFIG_SENSORS_EEPROM=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y CONFIG_HWMON_VID=y -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set # CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set @@ -905,12 +955,12 @@ CONFIG_HWMON_VID=y # CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set -# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ADT7470 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set # CONFIG_SENSORS_F71805F is not set -# CONFIG_SENSORS_FSCHER is not set -# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set # CONFIG_SENSORS_GL518SM is not set # CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set @@ -946,6 +996,13 @@ CONFIG_SENSORS_LM90=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -963,14 +1020,14 @@ CONFIG_DAB=y # # Graphics support # -CONFIG_BACKLIGHT_LCD_SUPPORT=y -CONFIG_LCD_CLASS_DEVICE=m -CONFIG_BACKLIGHT_CLASS_DEVICE=y - -# -# Display device support -# -# CONFIG_DISPLAY_SUPPORT is not set +# CONFIG_AGP is not set +CONFIG_DRM=y +# CONFIG_DRM_TDFX is not set +# CONFIG_DRM_R128 is not set +CONFIG_DRM_RADEON=y +# CONFIG_DRM_MGA is not set +# CONFIG_DRM_VIA is not set +# CONFIG_DRM_SAVAGE is not set CONFIG_VGASTATE=y # CONFIG_VIDEO_OUTPUT_CONTROL is not set CONFIG_FB=y @@ -979,6 +1036,7 @@ CONFIG_FB_DDC=y CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set # CONFIG_FB_SYS_FILLRECT is not set # CONFIG_FB_SYS_COPYAREA is not set # CONFIG_FB_SYS_IMAGEBLIT is not set @@ -1026,6 +1084,15 @@ CONFIG_FB_RADEON_BACKLIGHT=y # CONFIG_FB_PM3 is not set # CONFIG_FB_IBM_GXT4500 is not set # CONFIG_FB_VIRTUAL is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +# CONFIG_LCD_CLASS_DEVICE is not set +CONFIG_BACKLIGHT_CLASS_DEVICE=y +# CONFIG_BACKLIGHT_CORGI is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set # # Console display driver support @@ -1178,6 +1245,7 @@ CONFIG_SND_USB_USX2Y=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -1328,6 +1396,7 @@ CONFIG_RTC_INTF_DEV=y # I2C RTC drivers # CONFIG_RTC_DRV_DS1307=y +# CONFIG_RTC_DRV_DS1374 is not set # CONFIG_RTC_DRV_DS1672 is not set # CONFIG_RTC_DRV_MAX6900 is not set # CONFIG_RTC_DRV_RS5C372 is not set @@ -1357,19 +1426,6 @@ CONFIG_RTC_DRV_DS1307=y # # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -1388,7 +1444,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -1436,7 +1491,6 @@ CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set CONFIG_HUGETLBFS=y CONFIG_HUGETLB_PAGE=y -CONFIG_RAMFS=y CONFIG_CONFIGFS_FS=y # @@ -1449,30 +1503,43 @@ CONFIG_CONFIGFS_FS=y # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set -# CONFIG_JFFS2_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set # CONFIG_NFS_V4 is not set # CONFIG_NFS_DIRECTIO is not set -# CONFIG_NFSD is not set +CONFIG_NFSD=y +CONFIG_NFSD_V3=y +# CONFIG_NFSD_V3_ACL is not set +CONFIG_NFSD_V4=y +CONFIG_NFSD_TCP=y CONFIG_ROOT_NFS=y CONFIG_LOCKD=y CONFIG_LOCKD_V4=y +CONFIG_EXPORTFS=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y # CONFIG_SUNRPC_BIND34 is not set -# CONFIG_RPCSEC_GSS_KRB5 is not set +CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set # CONFIG_CIFS is not set @@ -1501,10 +1568,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y @@ -1545,10 +1608,6 @@ CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1561,23 +1620,24 @@ CONFIG_CRC_CCITT=y # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y # CONFIG_CRC7 is not set -# CONFIG_LIBCRC32C is not set +CONFIG_LIBCRC32C=m +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# +CONFIG_INSTRUMENTATION=y CONFIG_PROFILING=y CONFIG_OPROFILE=y # CONFIG_KPROBES is not set +# CONFIG_MARKERS is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -1586,7 +1646,7 @@ CONFIG_MAGIC_SYSRQ=y CONFIG_DEBUG_KERNEL=y # CONFIG_DEBUG_SHIRQ is not set CONFIG_DETECT_SOFTLOCKUP=y -CONFIG_SCHED_DEBUG=y +# CONFIG_SCHED_DEBUG is not set # CONFIG_SCHEDSTATS is not set # CONFIG_TIMER_STATS is not set # CONFIG_SLUB_DEBUG_ON is not set @@ -1601,9 +1661,12 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set # CONFIG_FORCED_INLINING is not set +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -1620,6 +1683,7 @@ CONFIG_XMON_DISASSEMBLY=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1628,34 +1692,38 @@ CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_HMAC=y # CONFIG_CRYPTO_XCBC is not set # CONFIG_CRYPTO_NULL is not set -# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD4=y CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_SHA1=y -# CONFIG_CRYPTO_SHA256 is not set -# CONFIG_CRYPTO_SHA512 is not set +CONFIG_CRYPTO_SHA256=y +CONFIG_CRYPTO_SHA512=y # CONFIG_CRYPTO_WP512 is not set # CONFIG_CRYPTO_TGR192 is not set # CONFIG_CRYPTO_GF128MUL is not set -CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_ECB is not set CONFIG_CRYPTO_CBC=y -CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_PCBC is not set # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set -# CONFIG_CRYPTO_BLOWFISH is not set +CONFIG_CRYPTO_BLOWFISH=y # CONFIG_CRYPTO_TWOFISH is not set # CONFIG_CRYPTO_SERPENT is not set -# CONFIG_CRYPTO_AES is not set +CONFIG_CRYPTO_AES=y # CONFIG_CRYPTO_CAST5 is not set # CONFIG_CRYPTO_CAST6 is not set # CONFIG_CRYPTO_TEA is not set # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set -# CONFIG_CRYPTO_HW is not set +# CONFIG_CRYPTO_AUTHENC is not set +CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/ppc64_defconfig b/arch/powerpc/configs/ppc64_defconfig index 05582af50c5..3e90c835fe1 100644 --- a/arch/powerpc/configs/ppc64_defconfig +++ b/arch/powerpc/configs/ppc64_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Thu Aug 30 16:47:09 2007 +# Linux kernel version: 2.6.24-rc2 +# Tue Nov 6 23:43:56 2007 # CONFIG_PPC64=y @@ -11,6 +11,7 @@ CONFIG_PPC64=y # CONFIG_POWER4_ONLY is not set CONFIG_POWER3=y CONFIG_POWER4=y +# CONFIG_TUNE_CELL is not set CONFIG_PPC_FPU=y CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y @@ -19,8 +20,13 @@ CONFIG_VIRT_CPU_ACCOUNTING=y CONFIG_SMP=y CONFIG_NR_CPUS=32 CONFIG_64BIT=y +CONFIG_WORD_SIZE=64 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -72,8 +78,15 @@ CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=17 CONFIG_CGROUPS=y +# CONFIG_CGROUP_DEBUG is not set +# CONFIG_CGROUP_NS is not set +# CONFIG_CGROUP_CPUACCT is not set CONFIG_CPUSETS=y +CONFIG_FAIR_GROUP_SCHED=y +CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y +CONFIG_PROC_PID_CPUSET=y CONFIG_RELAY=y CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="" @@ -93,7 +106,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -114,6 +126,7 @@ CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y CONFIG_BLK_DEV_IO_TRACE=y CONFIG_BLK_DEV_BSG=y +CONFIG_BLOCK_COMPAT=y # # IO Schedulers @@ -132,7 +145,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -155,7 +167,15 @@ CONFIG_VIOPATH=y CONFIG_PPC_PMAC=y CONFIG_PPC_PMAC64=y CONFIG_PPC_MAPLE=y -# CONFIG_PPC_PASEMI is not set +CONFIG_PPC_PASEMI=y + +# +# PA Semi PWRficient options +# +CONFIG_PPC_PASEMI_IOMMU=y +# CONFIG_PPC_PASEMI_IOMMU_DMA_FORCE is not set +CONFIG_PPC_PASEMI_MDIO=y +CONFIG_ELECTRA_IDE=y CONFIG_PPC_CELLEB=y # CONFIG_PPC_PS3 is not set CONFIG_PPC_CELL=y @@ -188,6 +208,7 @@ CONFIG_RTAS_FLASH=m CONFIG_PPC_PMI=m CONFIG_MMIO_NVRAM=y CONFIG_MPIC_U3_HT_IRQS=y +CONFIG_MPIC_BROKEN_REGREAD=y CONFIG_IBMVIO=y # CONFIG_IBMEBUS is not set # CONFIG_PPC_MPC106 is not set @@ -201,6 +222,8 @@ CONFIG_CPU_FREQ_STAT=y # CONFIG_CPU_FREQ_STAT_DETAILS is not set CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y # CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set CONFIG_CPU_FREQ_GOV_PERFORMANCE=y CONFIG_CPU_FREQ_GOV_POWERSAVE=y CONFIG_CPU_FREQ_GOV_USERSPACE=y @@ -211,6 +234,7 @@ CONFIG_CPU_FREQ_GOV_USERSPACE=y # CPU Frequency drivers # CONFIG_CPU_FREQ_PMAC64=y +CONFIG_PPC_PASEMI_CPUFREQ=y # CONFIG_CPM2 is not set CONFIG_AXON_RAM=m # CONFIG_FSL_ULI1575 is not set @@ -254,6 +278,8 @@ CONFIG_SPARSEMEM=y CONFIG_HAVE_MEMORY_PRESENT=y # CONFIG_SPARSEMEM_STATIC is not set CONFIG_SPARSEMEM_EXTREME=y +CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y +CONFIG_SPARSEMEM_VMEMMAP=y CONFIG_MEMORY_HOTPLUG=y CONFIG_MEMORY_HOTPLUG_SPARSE=y CONFIG_SPLIT_PTLOCK_CPUS=4 @@ -268,6 +294,7 @@ CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set CONFIG_SUSPEND_SMP_POSSIBLE=y +CONFIG_HIBERNATION_SMP_POSSIBLE=y CONFIG_SECCOMP=y # CONFIG_WANT_DEVICE_TREE is not set CONFIG_ISA_DMA_API=y @@ -284,12 +311,22 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_PCI_MSI=y +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set +CONFIG_PCCARD=y +# CONFIG_PCMCIA_DEBUG is not set +CONFIG_PCMCIA=y +CONFIG_PCMCIA_LOAD_CIS=y +CONFIG_PCMCIA_IOCTL=y +CONFIG_CARDBUS=y # -# PCCARD (PCMCIA/CardBus) support +# PC-card bridges # -# CONFIG_PCCARD is not set +# CONFIG_YENTA is not set +# CONFIG_PD6729 is not set +# CONFIG_I82092 is not set +CONFIG_ELECTRA_CF=y CONFIG_HOTPLUG_PCI=m # CONFIG_HOTPLUG_PCI_FAKE is not set # CONFIG_HOTPLUG_PCI_CPCI is not set @@ -319,7 +356,10 @@ CONFIG_INET=y CONFIG_IP_MULTICAST=y # CONFIG_IP_ADVANCED_ROUTER is not set CONFIG_IP_FIB_HASH=y -# CONFIG_IP_PNP is not set +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set CONFIG_NET_IPIP=y # CONFIG_NET_IPGRE is not set # CONFIG_IP_MROUTE is not set @@ -333,6 +373,7 @@ CONFIG_INET_TUNNEL=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -404,6 +445,7 @@ CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m +# CONFIG_NETFILTER_XT_MATCH_TIME is not set CONFIG_NETFILTER_XT_MATCH_U32=m CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m @@ -465,10 +507,6 @@ CONFIG_LLC=y # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set CONFIG_NET_CLS_ROUTE=y @@ -498,6 +536,7 @@ CONFIG_NET_CLS_ROUTE=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -539,6 +578,8 @@ CONFIG_BLK_DEV_IDE=y # CONFIG_BLK_DEV_IDE_SATA is not set CONFIG_BLK_DEV_IDEDISK=y # CONFIG_IDEDISK_MULTI_MODE is not set +# CONFIG_BLK_DEV_IDECS is not set +# CONFIG_BLK_DEV_DELKIN is not set CONFIG_BLK_DEV_IDECD=y # CONFIG_BLK_DEV_IDETAPE is not set # CONFIG_BLK_DEV_IDEFLOPPY is not set @@ -550,6 +591,11 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_IDEPCI_PCIBUS_ORDER=y @@ -557,8 +603,6 @@ CONFIG_IDEPCI_PCIBUS_ORDER=y CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDEDMA_FORCED is not set -# CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set CONFIG_BLK_DEV_AMD74XX=y @@ -590,7 +634,7 @@ CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y CONFIG_BLK_DEV_IDEDMA_PMAC=y # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_IDEDMA_IVB is not set +CONFIG_IDE_ARCH_OBSOLETE_INIT=y # CONFIG_BLK_DEV_HD is not set # @@ -631,6 +675,7 @@ CONFIG_SCSI_FC_ATTRS=y CONFIG_SCSI_ISCSI_ATTRS=m # CONFIG_SCSI_SAS_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +CONFIG_SCSI_SRP_ATTRS=y CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -671,19 +716,20 @@ CONFIG_SCSI_LPFC=m # CONFIG_SCSI_DC390T is not set CONFIG_SCSI_DEBUG=m # CONFIG_SCSI_SRP is not set +# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set CONFIG_ATA=y CONFIG_ATA_NONSTANDARD=y # CONFIG_SATA_AHCI is not set CONFIG_SATA_SVW=y # CONFIG_ATA_PIIX is not set -# CONFIG_SATA_MV is not set +CONFIG_SATA_MV=y # CONFIG_SATA_NV is not set # CONFIG_PDC_ADMA is not set # CONFIG_SATA_QSTOR is not set # CONFIG_SATA_PROMISE is not set # CONFIG_SATA_SX4 is not set # CONFIG_SATA_SIL is not set -# CONFIG_SATA_SIL24 is not set +CONFIG_SATA_SIL24=y # CONFIG_SATA_SIS is not set # CONFIG_SATA_ULI is not set # CONFIG_SATA_VIA is not set @@ -713,8 +759,10 @@ CONFIG_SATA_SVW=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set +CONFIG_PATA_PCMCIA=y # CONFIG_PATA_PDC_OLD is not set # CONFIG_PATA_RADISYS is not set # CONFIG_PATA_RZ1000 is not set @@ -725,6 +773,7 @@ CONFIG_SATA_SVW=y # CONFIG_PATA_SIS is not set # CONFIG_PATA_VIA is not set CONFIG_PATA_WINBOND=y +CONFIG_PATA_PLATFORM=y CONFIG_PATA_SCC=y CONFIG_MD=y CONFIG_BLK_DEV_MD=y @@ -745,15 +794,10 @@ CONFIG_DM_ZERO=m CONFIG_DM_MULTIPATH=m CONFIG_DM_MULTIPATH_EMC=m # CONFIG_DM_MULTIPATH_RDAC is not set +# CONFIG_DM_MULTIPATH_HP is not set # CONFIG_DM_DELAY is not set - -# -# Fusion MPT device support -# +# CONFIG_DM_UEVENT is not set # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -800,13 +844,15 @@ CONFIG_BONDING=m # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set CONFIG_TUN=m +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set -CONFIG_PHYLIB=m +CONFIG_PHYLIB=y # # MII PHY device drivers # -CONFIG_MARVELL_PHY=m +CONFIG_MARVELL_PHY=y # CONFIG_DAVICOM_PHY is not set # CONFIG_QSEMI_PHY is not set # CONFIG_LXT_PHY is not set @@ -818,6 +864,9 @@ CONFIG_BROADCOM_PHY=m CONFIG_FIXED_PHY=m CONFIG_FIXED_MII_10_FDX=y CONFIG_FIXED_MII_100_FDX=y +# CONFIG_FIXED_MII_1000_FDX is not set +CONFIG_FIXED_MII_AMNT=1 +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -829,6 +878,11 @@ CONFIG_VORTEX=y # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set CONFIG_IBMVETH=m +# CONFIG_IBM_NEW_EMAC is not set +CONFIG_IBM_NEW_EMAC_ZMII=y +CONFIG_IBM_NEW_EMAC_RGMII=y +CONFIG_IBM_NEW_EMAC_TAH=y +CONFIG_IBM_NEW_EMAC_EMAC4=y CONFIG_NET_PCI=y CONFIG_PCNET32=y # CONFIG_PCNET32_NAPI is not set @@ -836,7 +890,6 @@ CONFIG_PCNET32=y # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set CONFIG_E100=y # CONFIG_FEALNX is not set @@ -856,6 +909,7 @@ CONFIG_ACENIC_OMIT_TIGON_I=y CONFIG_E1000=y # CONFIG_E1000_NAPI is not set # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -863,6 +917,7 @@ CONFIG_E1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set CONFIG_TIGON3=y # CONFIG_BNX2 is not set @@ -872,13 +927,16 @@ CONFIG_SPIDER_NET=m CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set CONFIG_IXGB=m # CONFIG_IXGB_NAPI is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set -CONFIG_PASEMI_MAC=m +# CONFIG_NIU is not set +CONFIG_PASEMI_MAC=y # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set CONFIG_TR=y CONFIG_IBMOL=y # CONFIG_3C359 is not set @@ -899,6 +957,7 @@ CONFIG_IBMOL=y # CONFIG_USB_RTL8150 is not set # CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set +# CONFIG_NET_PCMCIA is not set # CONFIG_WAN is not set CONFIG_ISERIES_VETH=m # CONFIG_FDDI is not set @@ -918,6 +977,7 @@ CONFIG_SLHC=m # CONFIG_NET_FC is not set # CONFIG_SHAPER is not set CONFIG_NETCONSOLE=y +# CONFIG_NETCONSOLE_DYNAMIC is not set CONFIG_NETPOLL=y CONFIG_NETPOLL_TRAP=y CONFIG_NET_POLL_CONTROLLER=y @@ -939,7 +999,6 @@ CONFIG_INPUT_MOUSEDEV=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set CONFIG_INPUT_EVDEV=m # CONFIG_INPUT_EVBUG is not set @@ -1002,6 +1061,7 @@ CONFIG_HW_CONSOLE=y CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_PCI=y +# CONFIG_SERIAL_8250_CS is not set CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -1029,14 +1089,18 @@ CONFIG_HVC_RTAS=y CONFIG_HVC_BEAT=y CONFIG_HVCS=m # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set + +# +# PCMCIA character devices +# +# CONFIG_SYNCLINK_CS is not set +# CONFIG_CARDMAN_4000 is not set +# CONFIG_CARDMAN_4040 is not set CONFIG_RAW_DRIVER=y CONFIG_MAX_RAW_DEVS=256 # CONFIG_HANGCHECK_TIMER is not set @@ -1068,6 +1132,7 @@ CONFIG_I2C_POWERMAC=y # CONFIG_I2C_NFORCE2 is not set # CONFIG_I2C_OCORES is not set # CONFIG_I2C_PARPORT_LIGHT is not set +CONFIG_I2C_PASEMI=y # CONFIG_I2C_PROSAVAGE is not set # CONFIG_I2C_SAVAGE4 is not set # CONFIG_I2C_SIMTEC is not set @@ -1106,6 +1171,13 @@ CONFIG_I2C_POWERMAC=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -1122,18 +1194,8 @@ CONFIG_I2C_POWERMAC=y # # Graphics support # -CONFIG_BACKLIGHT_LCD_SUPPORT=y -CONFIG_LCD_CLASS_DEVICE=y -CONFIG_BACKLIGHT_CLASS_DEVICE=y - -# -# Display device support -# -CONFIG_DISPLAY_SUPPORT=y - -# -# Display hardware drivers -# +# CONFIG_AGP is not set +# CONFIG_DRM is not set # CONFIG_VGASTATE is not set CONFIG_VIDEO_OUTPUT_CONTROL=m CONFIG_FB=y @@ -1142,6 +1204,7 @@ CONFIG_FB_DDC=y CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set # CONFIG_FB_SYS_FILLRECT is not set # CONFIG_FB_SYS_COPYAREA is not set # CONFIG_FB_SYS_IMAGEBLIT is not set @@ -1192,6 +1255,19 @@ CONFIG_FB_RADEON_BACKLIGHT=y # CONFIG_FB_PM3 is not set CONFIG_FB_IBM_GXT4500=y # CONFIG_FB_VIRTUAL is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_LCD_CLASS_DEVICE=y +CONFIG_BACKLIGHT_CLASS_DEVICE=y +# CONFIG_BACKLIGHT_CORGI is not set + +# +# Display device support +# +CONFIG_DISPLAY_SUPPORT=y + +# +# Display hardware drivers +# # # Console display driver support @@ -1333,6 +1409,12 @@ CONFIG_SND_AOA_SOUNDBUS_I2S=m # CONFIG_SND_USB_CAIAQ is not set # +# PCMCIA devices +# +# CONFIG_SND_VXPOCKET is not set +# CONFIG_SND_PDAUDIOCF is not set + +# # System on Chip audio support # # CONFIG_SND_SOC is not set @@ -1348,6 +1430,7 @@ CONFIG_SND_AOA_SOUNDBUS_I2S=m CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -1489,19 +1572,53 @@ CONFIG_EDAC=y # # CONFIG_EDAC_DEBUG is not set CONFIG_EDAC_MM_EDAC=y -# CONFIG_RTC_CLASS is not set +CONFIG_EDAC_PASEMI=y +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +CONFIG_RTC_DRV_DS1307=y +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set # -# DMA Engine support +# SPI RTC drivers # -# CONFIG_DMA_ENGINE is not set # -# DMA Clients +# Platform RTC drivers # +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set # -# DMA Devices +# on-CPU RTC drivers # # @@ -1585,7 +1702,6 @@ CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set CONFIG_HUGETLBFS=y CONFIG_HUGETLB_PAGE=y -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1604,10 +1720,7 @@ CONFIG_CRAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y @@ -1619,6 +1732,7 @@ CONFIG_NFSD_V3=y CONFIG_NFSD_V3_ACL=y CONFIG_NFSD_V4=y CONFIG_NFSD_TCP=y +CONFIG_ROOT_NFS=y CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=m @@ -1626,6 +1740,7 @@ CONFIG_NFS_ACL_SUPPORT=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y +CONFIG_SUNRPC_XPRT_RDMA=m # CONFIG_SUNRPC_BIND34 is not set CONFIG_RPCSEC_GSS_KRB5=y CONFIG_RPCSEC_GSS_SPKM3=m @@ -1662,10 +1777,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y @@ -1706,10 +1817,6 @@ CONFIG_NLS_ISO8859_15=m CONFIG_NLS_KOI8_R=m CONFIG_NLS_KOI8_U=m CONFIG_NLS_UTF8=m - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1733,18 +1840,17 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# +CONFIG_INSTRUMENTATION=y CONFIG_PROFILING=y CONFIG_OPROFILE=y # CONFIG_KPROBES is not set +# CONFIG_MARKERS is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -1768,9 +1874,12 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set CONFIG_DEBUG_STACKOVERFLOW=y CONFIG_DEBUG_STACK_USAGE=y # CONFIG_DEBUG_PAGEALLOC is not set @@ -1780,6 +1889,7 @@ CONFIG_XMON=y # CONFIG_XMON_DEFAULT is not set CONFIG_XMON_DISASSEMBLY=y CONFIG_IRQSTACKS=y +# CONFIG_VIRQ_DEBUG is not set CONFIG_BOOTX_TEXT=y # CONFIG_PPC_EARLY_DEBUG is not set @@ -1788,6 +1898,7 @@ CONFIG_BOOTX_TEXT=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=y CONFIG_ASYNC_CORE=y CONFIG_ASYNC_MEMCPY=y @@ -1812,6 +1923,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1826,9 +1938,12 @@ CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_KHAZAD=m CONFIG_CRYPTO_ANUBIS=m +# CONFIG_CRYPTO_SEED is not set CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_CRC32C=m # CONFIG_CRYPTO_CAMELLIA is not set CONFIG_CRYPTO_TEST=m +# CONFIG_CRYPTO_AUTHENC is not set # CONFIG_CRYPTO_HW is not set +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/kernel/cputable.c b/arch/powerpc/kernel/cputable.c index d3fb7d0c6c1..9ed351f3c96 100644 --- a/arch/powerpc/kernel/cputable.c +++ b/arch/powerpc/kernel/cputable.c @@ -1104,6 +1104,16 @@ static struct cpu_spec __initdata cpu_specs[] = { { .pvr_mask = 0xf0000fff, .pvr_value = 0x40000850, + .cpu_name = "440GR Rev. A", + .cpu_features = CPU_FTRS_44X, + .cpu_user_features = COMMON_USER_BOOKE, + .icache_bsize = 32, + .dcache_bsize = 32, + .platform = "ppc440", + }, + { /* Use logical PVR for 440EP (logical pvr = pvr | 0x8) */ + .pvr_mask = 0xf0000fff, + .pvr_value = 0x40000858, .cpu_name = "440EP Rev. A", .cpu_features = CPU_FTRS_44X, .cpu_user_features = COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU, @@ -1115,28 +1125,27 @@ static struct cpu_spec __initdata cpu_specs[] = { { .pvr_mask = 0xf0000fff, .pvr_value = 0x400008d3, - .cpu_name = "440EP Rev. B", + .cpu_name = "440GR Rev. B", .cpu_features = CPU_FTRS_44X, .cpu_user_features = COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU, .icache_bsize = 32, .dcache_bsize = 32, - .cpu_setup = __setup_cpu_440ep, .platform = "ppc440", }, - { /* 440EPX */ - .pvr_mask = 0xf0000ffb, - .pvr_value = 0x200008D0, - .cpu_name = "440EPX", + { /* Use logical PVR for 440EP (logical pvr = pvr | 0x8) */ + .pvr_mask = 0xf0000fff, + .pvr_value = 0x400008db, + .cpu_name = "440EP Rev. B", .cpu_features = CPU_FTRS_44X, .cpu_user_features = COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU, .icache_bsize = 32, .dcache_bsize = 32, - .cpu_setup = __setup_cpu_440epx, + .cpu_setup = __setup_cpu_440ep, .platform = "ppc440", }, { /* 440GRX */ .pvr_mask = 0xf0000ffb, - .pvr_value = 0x200008D8, + .pvr_value = 0x200008D0, .cpu_name = "440GRX", .cpu_features = CPU_FTRS_44X, .cpu_user_features = COMMON_USER_BOOKE, @@ -1145,6 +1154,17 @@ static struct cpu_spec __initdata cpu_specs[] = { .cpu_setup = __setup_cpu_440grx, .platform = "ppc440", }, + { /* Use logical PVR for 440EPx (logical pvr = pvr | 0x8) */ + .pvr_mask = 0xf0000ffb, + .pvr_value = 0x200008D8, + .cpu_name = "440EPX", + .cpu_features = CPU_FTRS_44X, + .cpu_user_features = COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU, + .icache_bsize = 32, + .dcache_bsize = 32, + .cpu_setup = __setup_cpu_440epx, + .platform = "ppc440", + }, { /* 440GP Rev. B */ .pvr_mask = 0xf0000fff, .pvr_value = 0x40000440, diff --git a/arch/powerpc/kernel/entry_32.S b/arch/powerpc/kernel/entry_32.S index 21d889e63e8..a7572cf464b 100644 --- a/arch/powerpc/kernel/entry_32.S +++ b/arch/powerpc/kernel/entry_32.S @@ -244,6 +244,13 @@ syscall_exit_cont: andis. r10,r0,DBCR0_IC@h bnel- load_dbcr0 #endif +#ifdef CONFIG_44x + lis r4,icache_44x_need_flush@ha + lwz r5,icache_44x_need_flush@l(r4) + cmplwi cr0,r5,0 + bne- 2f +1: +#endif /* CONFIG_44x */ stwcx. r0,0,r1 /* to clear the reservation */ lwz r4,_LINK(r1) lwz r5,_CCR(r1) @@ -258,6 +265,12 @@ syscall_exit_cont: mtspr SPRN_SRR1,r8 SYNC RFI +#ifdef CONFIG_44x +2: li r7,0 + iccci r0,r0 + stw r7,icache_44x_need_flush@l(r4) + b 1b +#endif /* CONFIG_44x */ 66: li r3,-ENOSYS b ret_from_syscall @@ -683,6 +696,16 @@ resume_kernel: /* interrupts are hard-disabled at this point */ restore: +#ifdef CONFIG_44x + lis r4,icache_44x_need_flush@ha + lwz r5,icache_44x_need_flush@l(r4) + cmplwi cr0,r5,0 + beq+ 1f + li r6,0 + iccci r0,r0 + stw r6,icache_44x_need_flush@l(r4) +1: +#endif /* CONFIG_44x */ lwz r0,GPR0(r1) lwz r2,GPR2(r1) REST_4GPRS(3, r1) diff --git a/arch/powerpc/kernel/head_64.S b/arch/powerpc/kernel/head_64.S index 97c5857faf0..c34986835a4 100644 --- a/arch/powerpc/kernel/head_64.S +++ b/arch/powerpc/kernel/head_64.S @@ -904,7 +904,7 @@ handle_page_fault: */ 12: bl .save_nvgprs addi r3,r1,STACK_FRAME_OVERHEAD - lwz r4,_DAR(r1) + ld r4,_DAR(r1) bl .low_hash_fault b .ret_from_except diff --git a/arch/powerpc/kernel/idle.c b/arch/powerpc/kernel/idle.c index abd2957fe53..c3cf0e8f3ac 100644 --- a/arch/powerpc/kernel/idle.c +++ b/arch/powerpc/kernel/idle.c @@ -122,7 +122,7 @@ static ctl_table powersave_nap_sysctl_root[] = { { .ctl_name = CTL_KERN, .procname = "kernel", - .mode = 0755, + .mode = 0555, .child = powersave_nap_ctl_table, }, {} diff --git a/arch/powerpc/kernel/misc_32.S b/arch/powerpc/kernel/misc_32.S index 8533de50347..8b642ab26d3 100644 --- a/arch/powerpc/kernel/misc_32.S +++ b/arch/powerpc/kernel/misc_32.S @@ -288,7 +288,16 @@ _GLOBAL(_tlbia) */ _GLOBAL(_tlbie) #if defined(CONFIG_40x) + /* We run the search with interrupts disabled because we have to change + * the PID and I don't want to preempt when that happens. + */ + mfmsr r5 + mfspr r6,SPRN_PID + wrteei 0 + mtspr SPRN_PID,r4 tlbsx. r3, 0, r3 + mtspr SPRN_PID,r6 + wrtee r5 bne 10f sync /* There are only 64 TLB entries, so r3 < 64, which means bit 25 is clear. @@ -297,23 +306,23 @@ _GLOBAL(_tlbie) tlbwe r3, r3, TLB_TAG isync 10: + #elif defined(CONFIG_44x) - mfspr r4,SPRN_MMUCR - mfspr r5,SPRN_PID /* Get PID */ - rlwimi r4,r5,0,24,31 /* Set TID */ + mfspr r5,SPRN_MMUCR + rlwimi r5,r4,0,24,31 /* Set TID */ /* We have to run the search with interrupts disabled, even critical * and debug interrupts (in fact the only critical exceptions we have * are debug and machine check). Otherwise an interrupt which causes * a TLB miss can clobber the MMUCR between the mtspr and the tlbsx. */ - mfmsr r5 + mfmsr r4 lis r6,(MSR_EE|MSR_CE|MSR_ME|MSR_DE)@ha addi r6,r6,(MSR_EE|MSR_CE|MSR_ME|MSR_DE)@l - andc r6,r5,r6 + andc r6,r4,r6 mtmsr r6 - mtspr SPRN_MMUCR,r4 + mtspr SPRN_MMUCR,r5 tlbsx. r3, 0, r3 - mtmsr r5 + mtmsr r4 bne 10f sync /* There are only 64 TLB entries, so r3 < 64, @@ -534,12 +543,21 @@ END_FTR_SECTION_IFSET(CPU_FTR_COHERENT_ICACHE) addi r3,r3,L1_CACHE_BYTES bdnz 0b sync +#ifndef CONFIG_44x + /* We don't flush the icache on 44x. Those have a virtual icache + * and we don't have access to the virtual address here (it's + * not the page vaddr but where it's mapped in user space). The + * flushing of the icache on these is handled elsewhere, when + * a change in the address space occurs, before returning to + * user space + */ mtctr r4 1: icbi 0,r6 addi r6,r6,L1_CACHE_BYTES bdnz 1b sync isync +#endif /* CONFIG_44x */ blr /* diff --git a/arch/powerpc/kernel/prom.c b/arch/powerpc/kernel/prom.c index 9f329a8928e..acc0d247d3c 100644 --- a/arch/powerpc/kernel/prom.c +++ b/arch/powerpc/kernel/prom.c @@ -697,6 +697,18 @@ static int __init early_init_dt_scan_cpus(unsigned long node, prop = of_get_flat_dt_prop(node, "cpu-version", NULL); if (prop && (*prop & 0xff000000) == 0x0f000000) identify_cpu(0, *prop); +#if defined(CONFIG_44x) && defined(CONFIG_PPC_FPU) + /* + * Since 440GR(x)/440EP(x) processors have the same pvr, + * we check the node path and set bit 28 in the cur_cpu_spec + * pvr for EP(x) processor version. This bit is always 0 in + * the "real" pvr. Then we call identify_cpu again with + * the new logical pvr to enable FPU support. + */ + if (strstr(uname, "440EP")) { + identify_cpu(0, cur_cpu_spec->pvr_value | 0x8); + } +#endif } check_cpu_feature_properties(node); diff --git a/arch/powerpc/kernel/prom_init.c b/arch/powerpc/kernel/prom_init.c index 1db10f70ae6..1add6efdb31 100644 --- a/arch/powerpc/kernel/prom_init.c +++ b/arch/powerpc/kernel/prom_init.c @@ -1244,7 +1244,7 @@ static void __init prom_initialize_tce_table(void) local_alloc_bottom = base; /* It seems OF doesn't null-terminate the path :-( */ - memset(path, 0, sizeof(path)); + memset(path, 0, PROM_SCRATCH_SIZE); /* Call OF to setup the TCE hardware */ if (call_prom("package-to-path", 3, 1, node, path, PROM_SCRATCH_SIZE-1) == PROM_ERROR) { diff --git a/arch/powerpc/kernel/setup_64.c b/arch/powerpc/kernel/setup_64.c index ede77dbbd4d..3b1529c103e 100644 --- a/arch/powerpc/kernel/setup_64.c +++ b/arch/powerpc/kernel/setup_64.c @@ -291,23 +291,16 @@ static void __init initialize_cache_info(void) if ( num_cpus == 1 ) { const u32 *sizep, *lsizep; u32 size, lsize; - const char *dc, *ic; - - /* Then read cache informations */ - if (machine_is(powermac)) { - dc = "d-cache-block-size"; - ic = "i-cache-block-size"; - } else { - dc = "d-cache-line-size"; - ic = "i-cache-line-size"; - } size = 0; lsize = cur_cpu_spec->dcache_bsize; sizep = of_get_property(np, "d-cache-size", NULL); if (sizep != NULL) size = *sizep; - lsizep = of_get_property(np, dc, NULL); + lsizep = of_get_property(np, "d-cache-block-size", NULL); + /* fallback if block size missing */ + if (lsizep == NULL) + lsizep = of_get_property(np, "d-cache-line-size", NULL); if (lsizep != NULL) lsize = *lsizep; if (sizep == 0 || lsizep == 0) @@ -324,7 +317,9 @@ static void __init initialize_cache_info(void) sizep = of_get_property(np, "i-cache-size", NULL); if (sizep != NULL) size = *sizep; - lsizep = of_get_property(np, ic, NULL); + lsizep = of_get_property(np, "i-cache-block-size", NULL); + if (lsizep == NULL) + lsizep = of_get_property(np, "i-cache-line-size", NULL); if (lsizep != NULL) lsize = *lsizep; if (sizep == 0 || lsizep == 0) diff --git a/arch/powerpc/kernel/swsusp_32.S b/arch/powerpc/kernel/swsusp_32.S index 69e8f86aa4f..77fc76607ab 100644 --- a/arch/powerpc/kernel/swsusp_32.S +++ b/arch/powerpc/kernel/swsusp_32.S @@ -133,10 +133,12 @@ _GLOBAL(swsusp_arch_suspend) /* Resume code */ _GLOBAL(swsusp_arch_resume) +#ifdef CONFIG_ALTIVEC /* Stop pending alitvec streams and memory accesses */ BEGIN_FTR_SECTION DSSALL END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC) +#endif sync /* Disable MSR:DR to make sure we don't take a TLB or diff --git a/arch/powerpc/kernel/time.c b/arch/powerpc/kernel/time.c index 9eb3284deac..99ebcd3884d 100644 --- a/arch/powerpc/kernel/time.c +++ b/arch/powerpc/kernel/time.c @@ -586,7 +586,7 @@ void timer_interrupt(struct pt_regs * regs) /* not time for this event yet */ now = per_cpu(decrementer_next_tb, cpu) - now; if (now <= DECREMENTER_MAX) - set_dec((unsigned int)now - 1); + set_dec((int)now); return; } old_regs = set_irq_regs(regs); @@ -611,8 +611,6 @@ void timer_interrupt(struct pt_regs * regs) if (evt->event_handler) evt->event_handler(evt); - else - evt->set_next_event(DECREMENTER_MAX, evt); #ifdef CONFIG_PPC_ISERIES if (firmware_has_feature(FW_FEATURE_ISERIES) && hvlpevent_is_pending()) @@ -836,9 +834,6 @@ static int decrementer_set_next_event(unsigned long evt, struct clock_event_device *dev) { __get_cpu_var(decrementer_next_tb) = get_tb_or_rtc() + evt; - /* The decrementer interrupts on the 0 -> -1 transition */ - if (evt) - --evt; set_dec(evt); return 0; } @@ -871,7 +866,8 @@ void init_decrementer_clockevent(void) decrementer_clockevent.shift); decrementer_clockevent.max_delta_ns = clockevent_delta2ns(DECREMENTER_MAX, &decrementer_clockevent); - decrementer_clockevent.min_delta_ns = 1000; + decrementer_clockevent.min_delta_ns = + clockevent_delta2ns(2, &decrementer_clockevent); register_decrementer_clockevent(cpu); } diff --git a/arch/powerpc/kernel/vmlinux.lds.S b/arch/powerpc/kernel/vmlinux.lds.S index 823a8cbd60b..f66fa5d966b 100644 --- a/arch/powerpc/kernel/vmlinux.lds.S +++ b/arch/powerpc/kernel/vmlinux.lds.S @@ -37,11 +37,10 @@ SECTIONS ALIGN_FUNCTION(); *(.text.head) _text = .; - TEXT_TEXT + *(.text .fixup .text.init.refok .exit.text.refok) SCHED_TEXT LOCK_TEXT KPROBES_TEXT - *(.fixup) #ifdef CONFIG_PPC32 *(.got1) diff --git a/arch/powerpc/mm/40x_mmu.c b/arch/powerpc/mm/40x_mmu.c index e067df836be..3899ea97fbd 100644 --- a/arch/powerpc/mm/40x_mmu.c +++ b/arch/powerpc/mm/40x_mmu.c @@ -98,13 +98,12 @@ unsigned long __init mmu_mapin_ram(void) v = KERNELBASE; p = PPC_MEMSTART; - s = 0; + s = total_lowmem; - if (__map_without_ltlbs) { - return s; - } + if (__map_without_ltlbs) + return 0; - while (s <= (total_lowmem - LARGE_PAGE_SIZE_16M)) { + while (s >= LARGE_PAGE_SIZE_16M) { pmd_t *pmdp; unsigned long val = p | _PMD_SIZE_16M | _PAGE_HWEXEC | _PAGE_HWWRITE; @@ -116,10 +115,10 @@ unsigned long __init mmu_mapin_ram(void) v += LARGE_PAGE_SIZE_16M; p += LARGE_PAGE_SIZE_16M; - s += LARGE_PAGE_SIZE_16M; + s -= LARGE_PAGE_SIZE_16M; } - while (s <= (total_lowmem - LARGE_PAGE_SIZE_4M)) { + while (s >= LARGE_PAGE_SIZE_4M) { pmd_t *pmdp; unsigned long val = p | _PMD_SIZE_4M | _PAGE_HWEXEC | _PAGE_HWWRITE; @@ -128,8 +127,8 @@ unsigned long __init mmu_mapin_ram(void) v += LARGE_PAGE_SIZE_4M; p += LARGE_PAGE_SIZE_4M; - s += LARGE_PAGE_SIZE_4M; + s -= LARGE_PAGE_SIZE_4M; } - return s; + return total_lowmem - s; } diff --git a/arch/powerpc/mm/44x_mmu.c b/arch/powerpc/mm/44x_mmu.c index c3df5047653..04dc08798d3 100644 --- a/arch/powerpc/mm/44x_mmu.c +++ b/arch/powerpc/mm/44x_mmu.c @@ -35,6 +35,7 @@ */ unsigned int tlb_44x_index; /* = 0 */ unsigned int tlb_44x_hwater = PPC44x_TLB_SIZE - 1 - PPC44x_EARLY_TLBS; +int icache_44x_need_flush; /* * "Pins" a 256MB TLB entry in AS0 for kernel lowmem diff --git a/arch/powerpc/mm/fault.c b/arch/powerpc/mm/fault.c index a18fda361cc..8135da06e0a 100644 --- a/arch/powerpc/mm/fault.c +++ b/arch/powerpc/mm/fault.c @@ -309,7 +309,7 @@ good_area: set_bit(PG_arch_1, &page->flags); } pte_update(ptep, 0, _PAGE_HWEXEC); - _tlbie(address); + _tlbie(address, mm->context.id); pte_unmap_unlock(ptep, ptl); up_read(&mm->mmap_sem); return 0; diff --git a/arch/powerpc/mm/hash_low_64.S b/arch/powerpc/mm/hash_low_64.S index ad253b95903..e935edd6b72 100644 --- a/arch/powerpc/mm/hash_low_64.S +++ b/arch/powerpc/mm/hash_low_64.S @@ -331,7 +331,7 @@ htab_pte_insert_failure: *****************************************************************************/ /* _hash_page_4K(unsigned long ea, unsigned long access, unsigned long vsid, - * pte_t *ptep, unsigned long trap, int local) + * pte_t *ptep, unsigned long trap, int local, int ssize) */ /* @@ -557,7 +557,8 @@ htab_inval_old_hpte: mr r4,r31 /* PTE.pte */ li r5,0 /* PTE.hidx */ li r6,MMU_PAGE_64K /* psize */ - ld r7,STK_PARM(r8)(r1) /* local */ + ld r7,STK_PARM(r9)(r1) /* ssize */ + ld r8,STK_PARM(r8)(r1) /* local */ bl .flush_hash_page b htab_insert_pte diff --git a/arch/powerpc/mm/hash_utils_64.c b/arch/powerpc/mm/hash_utils_64.c index c78dc912411..f09730bf3a3 100644 --- a/arch/powerpc/mm/hash_utils_64.c +++ b/arch/powerpc/mm/hash_utils_64.c @@ -51,6 +51,7 @@ #include <asm/cputable.h> #include <asm/sections.h> #include <asm/spu.h> +#include <asm/udbg.h> #ifdef DEBUG #define DBG(fmt...) udbg_printf(fmt) @@ -791,8 +792,7 @@ int hash_page(unsigned long ea, unsigned long access, unsigned long trap) } if (user_region) { if (psize != get_paca()->context.user_psize) { - get_paca()->context.user_psize = - mm->context.user_psize; + get_paca()->context = mm->context; slb_flush_and_rebolt(); } } else if (get_paca()->vmalloc_sllp != @@ -885,6 +885,9 @@ void hash_preload(struct mm_struct *mm, unsigned long ea, local_irq_restore(flags); } +/* WARNING: This is called from hash_low_64.S, if you change this prototype, + * do not forget to update the assembly call site ! + */ void flush_hash_page(unsigned long va, real_pte_t pte, int psize, int ssize, int local) { diff --git a/arch/powerpc/mm/mmu_decl.h b/arch/powerpc/mm/mmu_decl.h index c94a64fd3c0..eb3a732e91d 100644 --- a/arch/powerpc/mm/mmu_decl.h +++ b/arch/powerpc/mm/mmu_decl.h @@ -61,12 +61,12 @@ extern unsigned long total_lowmem; #define mmu_mapin_ram() (0UL) #elif defined(CONFIG_4xx) -#define flush_HPTE(X, va, pg) _tlbie(va) +#define flush_HPTE(pid, va, pg) _tlbie(va, pid) extern void MMU_init_hw(void); extern unsigned long mmu_mapin_ram(void); #elif defined(CONFIG_FSL_BOOKE) -#define flush_HPTE(X, va, pg) _tlbie(va) +#define flush_HPTE(pid, va, pg) _tlbie(va, pid) extern void MMU_init_hw(void); extern unsigned long mmu_mapin_ram(void); extern void adjust_total_lowmem(void); diff --git a/arch/powerpc/mm/slb.c b/arch/powerpc/mm/slb.c index bbd2c512ee0..27922dff8b9 100644 --- a/arch/powerpc/mm/slb.c +++ b/arch/powerpc/mm/slb.c @@ -25,6 +25,7 @@ #include <asm/smp.h> #include <asm/firmware.h> #include <linux/compiler.h> +#include <asm/udbg.h> #ifdef DEBUG #define DBG(fmt...) udbg_printf(fmt) @@ -148,6 +149,35 @@ void slb_vmalloc_update(void) slb_flush_and_rebolt(); } +/* Helper function to compare esids. There are four cases to handle. + * 1. The system is not 1T segment size capable. Use the GET_ESID compare. + * 2. The system is 1T capable, both addresses are < 1T, use the GET_ESID compare. + * 3. The system is 1T capable, only one of the two addresses is > 1T. This is not a match. + * 4. The system is 1T capable, both addresses are > 1T, use the GET_ESID_1T macro to compare. + */ +static inline int esids_match(unsigned long addr1, unsigned long addr2) +{ + int esid_1t_count; + + /* System is not 1T segment size capable. */ + if (!cpu_has_feature(CPU_FTR_1T_SEGMENT)) + return (GET_ESID(addr1) == GET_ESID(addr2)); + + esid_1t_count = (((addr1 >> SID_SHIFT_1T) != 0) + + ((addr2 >> SID_SHIFT_1T) != 0)); + + /* both addresses are < 1T */ + if (esid_1t_count == 0) + return (GET_ESID(addr1) == GET_ESID(addr2)); + + /* One address < 1T, the other > 1T. Not a match */ + if (esid_1t_count == 1) + return 0; + + /* Both addresses are > 1T. */ + return (GET_ESID_1T(addr1) == GET_ESID_1T(addr2)); +} + /* Flush all user entries from the segment table of the current processor. */ void switch_slb(struct task_struct *tsk, struct mm_struct *mm) { @@ -193,15 +223,14 @@ void switch_slb(struct task_struct *tsk, struct mm_struct *mm) return; slb_allocate(pc); - if (GET_ESID(pc) == GET_ESID(stack)) + if (esids_match(pc,stack)) return; if (is_kernel_addr(stack)) return; slb_allocate(stack); - if ((GET_ESID(pc) == GET_ESID(unmapped_base)) - || (GET_ESID(stack) == GET_ESID(unmapped_base))) + if (esids_match(pc,unmapped_base) || esids_match(stack,unmapped_base)) return; if (is_kernel_addr(unmapped_base)) diff --git a/arch/powerpc/platforms/cell/interrupt.c b/arch/powerpc/platforms/cell/interrupt.c index 151fd8b82d6..04f74f9f9ab 100644 --- a/arch/powerpc/platforms/cell/interrupt.c +++ b/arch/powerpc/platforms/cell/interrupt.c @@ -158,6 +158,18 @@ static unsigned int iic_get_irq(void) return virq; } +void iic_setup_cpu(void) +{ + out_be64(&__get_cpu_var(iic).regs->prio, 0xff); +} + +u8 iic_get_target_id(int cpu) +{ + return per_cpu(iic, cpu).target_id; +} + +EXPORT_SYMBOL_GPL(iic_get_target_id); + #ifdef CONFIG_SMP /* Use the highest interrupt priorities for IPI */ @@ -166,29 +178,17 @@ static inline int iic_ipi_to_irq(int ipi) return IIC_IRQ_TYPE_IPI + 0xf - ipi; } -void iic_setup_cpu(void) -{ - out_be64(&__get_cpu_var(iic).regs->prio, 0xff); -} - void iic_cause_IPI(int cpu, int mesg) { out_be64(&per_cpu(iic, cpu).regs->generate, (0xf - mesg) << 4); } -u8 iic_get_target_id(int cpu) -{ - return per_cpu(iic, cpu).target_id; -} -EXPORT_SYMBOL_GPL(iic_get_target_id); - struct irq_host *iic_get_irq_host(int node) { return iic_host; } EXPORT_SYMBOL_GPL(iic_get_irq_host); - static irqreturn_t iic_ipi_action(int irq, void *dev_id) { int ipi = (int)(long)dev_id; diff --git a/arch/powerpc/platforms/cell/smp.c b/arch/powerpc/platforms/cell/smp.c index 1c0acbad742..e4438456c86 100644 --- a/arch/powerpc/platforms/cell/smp.c +++ b/arch/powerpc/platforms/cell/smp.c @@ -44,6 +44,7 @@ #include <asm/rtas.h> #include "interrupt.h" +#include <asm/udbg.h> #ifdef DEBUG #define DBG(fmt...) udbg_printf(fmt) diff --git a/arch/powerpc/platforms/celleb/setup.c b/arch/powerpc/platforms/celleb/setup.c index 1769d755eff..ddfb35ae741 100644 --- a/arch/powerpc/platforms/celleb/setup.c +++ b/arch/powerpc/platforms/celleb/setup.c @@ -49,6 +49,7 @@ #include <asm/machdep.h> #include <asm/cputable.h> #include <asm/irq.h> +#include <asm/time.h> #include <asm/spu_priv1.h> #include <asm/firmware.h> #include <asm/of_platform.h> diff --git a/arch/powerpc/platforms/iseries/irq.h b/arch/powerpc/platforms/iseries/irq.h index 69f1b437fc7..a1c23607403 100644 --- a/arch/powerpc/platforms/iseries/irq.h +++ b/arch/powerpc/platforms/iseries/irq.h @@ -1,9 +1,13 @@ #ifndef _ISERIES_IRQ_H #define _ISERIES_IRQ_H +#ifdef CONFIG_PCI extern void iSeries_init_IRQ(void); extern int iSeries_allocate_IRQ(HvBusNumber, HvSubBusNumber, u32); extern void iSeries_activate_IRQs(void); +#else +#define iSeries_init_IRQ NULL +#endif extern unsigned int iSeries_get_irq(void); #endif /* _ISERIES_IRQ_H */ diff --git a/arch/powerpc/platforms/iseries/setup.c b/arch/powerpc/platforms/iseries/setup.c index 37ae07ee54a..0877a883411 100644 --- a/arch/powerpc/platforms/iseries/setup.c +++ b/arch/powerpc/platforms/iseries/setup.c @@ -617,10 +617,6 @@ static void iseries_dedicated_idle(void) } } -#ifndef CONFIG_PCI -void __init iSeries_init_IRQ(void) { } -#endif - static void __iomem *iseries_ioremap(phys_addr_t address, unsigned long size, unsigned long flags) { diff --git a/arch/powerpc/platforms/iseries/vio.c b/arch/powerpc/platforms/iseries/vio.c index d6435b03971..be06cfd9fa3 100644 --- a/arch/powerpc/platforms/iseries/vio.c +++ b/arch/powerpc/platforms/iseries/vio.c @@ -523,15 +523,16 @@ static void __init get_viotape_info(struct device_node *vio_root) static int __init iseries_vio_init(void) { struct device_node *vio_root; + int ret = -ENODEV; if (!firmware_has_feature(FW_FEATURE_ISERIES)) - return -ENODEV; + goto out; iommu_vio_init(); vio_root = of_find_node_by_path("/vdevice"); if (!vio_root) - return -ENODEV; + goto out; if (viopath_hostLp == HvLpIndexInvalid) { vio_set_hostlp(); @@ -544,10 +545,11 @@ static int __init iseries_vio_init(void) get_viocd_info(vio_root); get_viotape_info(vio_root); - return 0; + ret = 0; put_node: of_node_put(vio_root); - return -ENODEV; + out: + return ret; } arch_initcall(iseries_vio_init); diff --git a/arch/powerpc/platforms/pseries/eeh.c b/arch/powerpc/platforms/pseries/eeh.c index 22322b35a0f..fb3d636e088 100644 --- a/arch/powerpc/platforms/pseries/eeh.c +++ b/arch/powerpc/platforms/pseries/eeh.c @@ -186,6 +186,11 @@ static size_t gather_pci_data(struct pci_dn *pdn, char * buf, size_t len) n += scnprintf(buf+n, len-n, "cmd/stat:%x\n", cfg); printk(KERN_WARNING "EEH: PCI cmd/status register: %08x\n", cfg); + if (!dev) { + printk(KERN_WARNING "EEH: no PCI device for this of node\n"); + return n; + } + /* Gather bridge-specific registers */ if (dev->class >> 16 == PCI_BASE_CLASS_BRIDGE) { rtas_read_config(pdn, PCI_SEC_STATUS, 2, &cfg); @@ -198,7 +203,7 @@ static size_t gather_pci_data(struct pci_dn *pdn, char * buf, size_t len) } /* Dump out the PCI-X command and status regs */ - cap = pci_find_capability(pdn->pcidev, PCI_CAP_ID_PCIX); + cap = pci_find_capability(dev, PCI_CAP_ID_PCIX); if (cap) { rtas_read_config(pdn, cap, 4, &cfg); n += scnprintf(buf+n, len-n, "pcix-cmd:%x\n", cfg); @@ -210,7 +215,7 @@ static size_t gather_pci_data(struct pci_dn *pdn, char * buf, size_t len) } /* If PCI-E capable, dump PCI-E cap 10, and the AER */ - cap = pci_find_capability(pdn->pcidev, PCI_CAP_ID_EXP); + cap = pci_find_capability(dev, PCI_CAP_ID_EXP); if (cap) { n += scnprintf(buf+n, len-n, "pci-e cap10:\n"); printk(KERN_WARNING @@ -222,7 +227,7 @@ static size_t gather_pci_data(struct pci_dn *pdn, char * buf, size_t len) printk(KERN_WARNING "EEH: PCI-E %02x: %08x\n", i, cfg); } - cap = pci_find_ext_capability(pdn->pcidev, PCI_EXT_CAP_ID_ERR); + cap = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_ERR); if (cap) { n += scnprintf(buf+n, len-n, "pci-e AER:\n"); printk(KERN_WARNING @@ -318,7 +323,7 @@ eeh_wait_for_slot_status(struct pci_dn *pdn, int max_wait_msecs) if (rets[2] == 0) return -1; /* permanently unavailable */ - if (max_wait_msecs <= 0) return -1; + if (max_wait_msecs <= 0) break; mwait = rets[2]; if (mwait <= 0) { diff --git a/arch/powerpc/platforms/pseries/eeh_driver.c b/arch/powerpc/platforms/pseries/eeh_driver.c index 15e015ef686..57e025e84ab 100644 --- a/arch/powerpc/platforms/pseries/eeh_driver.c +++ b/arch/powerpc/platforms/pseries/eeh_driver.c @@ -105,17 +105,18 @@ static void eeh_report_error(struct pci_dev *dev, void *userdata) return; rc = driver->err_handler->error_detected (dev, pci_channel_io_frozen); + + /* A driver that needs a reset trumps all others */ + if (rc == PCI_ERS_RESULT_NEED_RESET) *res = rc; if (*res == PCI_ERS_RESULT_NONE) *res = rc; - if (*res == PCI_ERS_RESULT_DISCONNECT && - rc == PCI_ERS_RESULT_NEED_RESET) *res = rc; } /** * eeh_report_mmio_enabled - tell drivers that MMIO has been enabled * - * Report an EEH error to each device driver, collect up and - * merge the device driver responses. Cumulative response - * passed back in "userdata". + * Tells each device driver that IO ports, MMIO and config space I/O + * are now enabled. Collects up and merges the device driver responses. + * Cumulative response passed back in "userdata". */ static void eeh_report_mmio_enabled(struct pci_dev *dev, void *userdata) @@ -123,17 +124,16 @@ static void eeh_report_mmio_enabled(struct pci_dev *dev, void *userdata) enum pci_ers_result rc, *res = userdata; struct pci_driver *driver = dev->driver; - // dev->error_state = pci_channel_mmio_enabled; - if (!driver || !driver->err_handler || !driver->err_handler->mmio_enabled) return; rc = driver->err_handler->mmio_enabled (dev); + + /* A driver that needs a reset trumps all others */ + if (rc == PCI_ERS_RESULT_NEED_RESET) *res = rc; if (*res == PCI_ERS_RESULT_NONE) *res = rc; - if (*res == PCI_ERS_RESULT_DISCONNECT && - rc == PCI_ERS_RESULT_NEED_RESET) *res = rc; } /** diff --git a/arch/powerpc/platforms/pseries/firmware.c b/arch/powerpc/platforms/pseries/firmware.c index 8b18a1c4009..b765b7c77b6 100644 --- a/arch/powerpc/platforms/pseries/firmware.c +++ b/arch/powerpc/platforms/pseries/firmware.c @@ -25,6 +25,7 @@ #include <asm/firmware.h> #include <asm/prom.h> +#include <asm/udbg.h> #ifdef DEBUG #define DBG(fmt...) udbg_printf(fmt) diff --git a/arch/powerpc/platforms/pseries/msi.c b/arch/powerpc/platforms/pseries/msi.c index 2793a1b100e..f15222bbe13 100644 --- a/arch/powerpc/platforms/pseries/msi.c +++ b/arch/powerpc/platforms/pseries/msi.c @@ -171,6 +171,7 @@ static int rtas_setup_msi_irqs(struct pci_dev *pdev, int nvec, int type) struct pci_dn *pdn; int hwirq, virq, i, rc; struct msi_desc *entry; + struct msi_msg msg; pdn = get_pdn(pdev); if (!pdn) @@ -213,6 +214,11 @@ static int rtas_setup_msi_irqs(struct pci_dev *pdev, int nvec, int type) dev_dbg(&pdev->dev, "rtas_msi: allocated virq %d\n", virq); set_irq_msi(virq, entry); + + /* Read config space back so we can restore after reset */ + read_msi_msg(virq, &msg); + entry->msg = msg; + unmask_msi_irq(virq); } diff --git a/arch/powerpc/sysdev/i8259.c b/arch/powerpc/sysdev/i8259.c index 7c1b27ac7d3..216c0f5680d 100644 --- a/arch/powerpc/sysdev/i8259.c +++ b/arch/powerpc/sysdev/i8259.c @@ -137,6 +137,7 @@ static void i8259_unmask_irq(unsigned int irq_nr) static struct irq_chip i8259_pic = { .typename = " i8259 ", .mask = i8259_mask_irq, + .disable = i8259_mask_irq, .unmask = i8259_unmask_irq, .mask_ack = i8259_mask_and_ack_irq, }; diff --git a/arch/powerpc/sysdev/mv64x60_pci.c b/arch/powerpc/sysdev/mv64x60_pci.c index 9b3baa7317d..6933f9c73b4 100644 --- a/arch/powerpc/sysdev/mv64x60_pci.c +++ b/arch/powerpc/sysdev/mv64x60_pci.c @@ -24,8 +24,9 @@ #define MV64X60_VAL_LEN_MAX 11 #define MV64X60_PCICFG_CPCI_HOTSWAP 0x68 -static ssize_t mv64x60_hs_reg_read(struct kobject *kobj, char *buf, loff_t off, - size_t count) +static ssize_t mv64x60_hs_reg_read(struct kobject *kobj, + struct bin_attribute *attr, char *buf, + loff_t off, size_t count) { struct pci_dev *phb; u32 v; @@ -44,8 +45,9 @@ static ssize_t mv64x60_hs_reg_read(struct kobject *kobj, char *buf, loff_t off, return sprintf(buf, "0x%08x\n", v); } -static ssize_t mv64x60_hs_reg_write(struct kobject *kobj, char *buf, loff_t off, - size_t count) +static ssize_t mv64x60_hs_reg_write(struct kobject *kobj, + struct bin_attribute *attr, char *buf, + loff_t off, size_t count) { struct pci_dev *phb; u32 v; diff --git a/arch/ppc/kernel/entry.S b/arch/ppc/kernel/entry.S index fba7ca17a67..b19bfef2034 100644 --- a/arch/ppc/kernel/entry.S +++ b/arch/ppc/kernel/entry.S @@ -244,6 +244,13 @@ syscall_exit_cont: andis. r10,r0,DBCR0_IC@h bnel- load_dbcr0 #endif +#ifdef CONFIG_44x + lis r4,icache_44x_need_flush@ha + lwz r5,icache_44x_need_flush@l(r4) + cmplwi cr0,r5,0 + bne- 2f +1: +#endif /* CONFIG_44x */ stwcx. r0,0,r1 /* to clear the reservation */ lwz r4,_LINK(r1) lwz r5,_CCR(r1) @@ -258,6 +265,12 @@ syscall_exit_cont: mtspr SPRN_SRR1,r8 SYNC RFI +#ifdef CONFIG_44x +2: li r7,0 + iccci r0,r0 + stw r7,icache_44x_need_flush@l(r4) + b 1b +#endif /* CONFIG_44x */ 66: li r3,-ENOSYS b ret_from_syscall @@ -679,6 +692,16 @@ resume_kernel: /* interrupts are hard-disabled at this point */ restore: +#ifdef CONFIG_44x + lis r4,icache_44x_need_flush@ha + lwz r5,icache_44x_need_flush@l(r4) + cmplwi cr0,r5,0 + beq+ 1f + li r6,0 + iccci r0,r0 + stw r6,icache_44x_need_flush@l(r4) +1: +#endif /* CONFIG_44x */ lwz r0,GPR0(r1) lwz r2,GPR2(r1) REST_4GPRS(3, r1) diff --git a/arch/ppc/kernel/misc.S b/arch/ppc/kernel/misc.S index a22e1f4d94c..e0c850d85c5 100644 --- a/arch/ppc/kernel/misc.S +++ b/arch/ppc/kernel/misc.S @@ -224,7 +224,16 @@ _GLOBAL(_tlbia) */ _GLOBAL(_tlbie) #if defined(CONFIG_40x) + /* We run the search with interrupts disabled because we have to change + * the PID and I don't want to preempt when that happens. + */ + mfmsr r5 + mfspr r6,SPRN_PID + wrteei 0 + mtspr SPRN_PID,r4 tlbsx. r3, 0, r3 + mtspr SPRN_PID,r6 + wrtee r5 bne 10f sync /* There are only 64 TLB entries, so r3 < 64, which means bit 25 is clear. @@ -234,22 +243,21 @@ _GLOBAL(_tlbie) isync 10: #elif defined(CONFIG_44x) - mfspr r4,SPRN_MMUCR - mfspr r5,SPRN_PID /* Get PID */ - rlwimi r4,r5,0,24,31 /* Set TID */ + mfspr r5,SPRN_MMUCR + rlwimi r5,r4,0,24,31 /* Set TID */ /* We have to run the search with interrupts disabled, even critical * and debug interrupts (in fact the only critical exceptions we have * are debug and machine check). Otherwise an interrupt which causes * a TLB miss can clobber the MMUCR between the mtspr and the tlbsx. */ - mfmsr r5 + mfmsr r4 lis r6,(MSR_EE|MSR_CE|MSR_ME|MSR_DE)@ha addi r6,r6,(MSR_EE|MSR_CE|MSR_ME|MSR_DE)@l - andc r6,r5,r6 + andc r6,r4,r6 mtmsr r6 - mtspr SPRN_MMUCR,r4 + mtspr SPRN_MMUCR,r5 tlbsx. r3, 0, r3 - mtmsr r5 + mtmsr r4 bne 10f sync /* There are only 64 TLB entries, so r3 < 64, @@ -491,12 +499,21 @@ END_FTR_SECTION_IFSET(CPU_FTR_COHERENT_ICACHE) addi r3,r3,L1_CACHE_BYTES bdnz 0b sync +#ifndef CONFIG_44x + /* We don't flush the icache on 44x. Those have a virtual icache + * and we don't have access to the virtual address here (it's + * not the page vaddr but where it's mapped in user space). The + * flushing of the icache on these is handled elsewhere, when + * a change in the address space occurs, before returning to + * user space + */ mtctr r4 1: icbi 0,r6 addi r6,r6,L1_CACHE_BYTES bdnz 1b sync isync +#endif /* CONFIG_44x */ blr /* diff --git a/arch/ppc/mm/44x_mmu.c b/arch/ppc/mm/44x_mmu.c index 0a0a0487b33..6536a25cfcb 100644 --- a/arch/ppc/mm/44x_mmu.c +++ b/arch/ppc/mm/44x_mmu.c @@ -61,6 +61,7 @@ extern char etext[], _stext[]; */ unsigned int tlb_44x_index = 0; unsigned int tlb_44x_hwater = 62; +int icache_44x_need_flush; /* * "Pins" a 256MB TLB entry in AS0 for kernel lowmem diff --git a/arch/ppc/mm/4xx_mmu.c b/arch/ppc/mm/4xx_mmu.c index 838e09db71d..ea785dbaac7 100644 --- a/arch/ppc/mm/4xx_mmu.c +++ b/arch/ppc/mm/4xx_mmu.c @@ -99,13 +99,12 @@ unsigned long __init mmu_mapin_ram(void) v = KERNELBASE; p = PPC_MEMSTART; - s = 0; + s = total_lowmem; - if (__map_without_ltlbs) { - return s; - } + if (__map_without_ltlbs) + return 0; - while (s <= (total_lowmem - LARGE_PAGE_SIZE_16M)) { + while (s >= LARGE_PAGE_SIZE_16M) { pmd_t *pmdp; unsigned long val = p | _PMD_SIZE_16M | _PAGE_HWEXEC | _PAGE_HWWRITE; @@ -117,10 +116,10 @@ unsigned long __init mmu_mapin_ram(void) v += LARGE_PAGE_SIZE_16M; p += LARGE_PAGE_SIZE_16M; - s += LARGE_PAGE_SIZE_16M; + s -= LARGE_PAGE_SIZE_16M; } - while (s <= (total_lowmem - LARGE_PAGE_SIZE_4M)) { + while (s >= LARGE_PAGE_SIZE_4M) { pmd_t *pmdp; unsigned long val = p | _PMD_SIZE_4M | _PAGE_HWEXEC | _PAGE_HWWRITE; @@ -129,8 +128,8 @@ unsigned long __init mmu_mapin_ram(void) v += LARGE_PAGE_SIZE_4M; p += LARGE_PAGE_SIZE_4M; - s += LARGE_PAGE_SIZE_4M; + s -= LARGE_PAGE_SIZE_4M; } - return s; + return total_lowmem - s; } diff --git a/arch/ppc/mm/fault.c b/arch/ppc/mm/fault.c index 254c23b755e..36c0e7529ed 100644 --- a/arch/ppc/mm/fault.c +++ b/arch/ppc/mm/fault.c @@ -227,7 +227,7 @@ good_area: set_bit(PG_arch_1, &page->flags); } pte_update(ptep, 0, _PAGE_HWEXEC); - _tlbie(address); + _tlbie(address, mm->context.id); pte_unmap_unlock(ptep, ptl); up_read(&mm->mmap_sem); return 0; diff --git a/arch/ppc/mm/mmu_decl.h b/arch/ppc/mm/mmu_decl.h index 540f3292b22..f1d4f2109a9 100644 --- a/arch/ppc/mm/mmu_decl.h +++ b/arch/ppc/mm/mmu_decl.h @@ -54,12 +54,12 @@ extern unsigned int num_tlbcam_entries; #define mmu_mapin_ram() (0UL) #elif defined(CONFIG_4xx) -#define flush_HPTE(X, va, pg) _tlbie(va) +#define flush_HPTE(pid, va, pg) _tlbie(va, pid) extern void MMU_init_hw(void); extern unsigned long mmu_mapin_ram(void); #elif defined(CONFIG_FSL_BOOKE) -#define flush_HPTE(X, va, pg) _tlbie(va) +#define flush_HPTE(pid, va, pg) _tlbie(va, pid) extern void MMU_init_hw(void); extern unsigned long mmu_mapin_ram(void); extern void adjust_total_lowmem(void); diff --git a/arch/ppc/platforms/4xx/ebony.c b/arch/ppc/platforms/4xx/ebony.c index 05d7184d7e1..453643a0eee 100644 --- a/arch/ppc/platforms/4xx/ebony.c +++ b/arch/ppc/platforms/4xx/ebony.c @@ -236,7 +236,7 @@ ebony_early_serial_map(void) gen550_init(0, &port); /* Purge TLB entry added in head_44x.S for early serial access */ - _tlbie(UART0_IO_BASE); + _tlbie(UART0_IO_BASE, 0); #endif port.membase = ioremap64(PPC440GP_UART1_ADDR, 8); diff --git a/arch/ppc/platforms/4xx/luan.c b/arch/ppc/platforms/4xx/luan.c index 4b169610f15..b79ebb8a3e6 100644 --- a/arch/ppc/platforms/4xx/luan.c +++ b/arch/ppc/platforms/4xx/luan.c @@ -230,9 +230,14 @@ luan_setup_hoses(void) /* Allocate hoses for PCIX1 and PCIX2 */ hose1 = pcibios_alloc_controller(); + if (!hose1) + return; + hose2 = pcibios_alloc_controller(); - if (!hose1 || !hose2) + if (!hose2) { + pcibios_free_controller(hose1); return; + } /* Setup PCIX1 */ hose1->first_busno = 0; diff --git a/arch/ppc/platforms/4xx/ocotea.c b/arch/ppc/platforms/4xx/ocotea.c index fd0f971881d..28a712cd480 100644 --- a/arch/ppc/platforms/4xx/ocotea.c +++ b/arch/ppc/platforms/4xx/ocotea.c @@ -259,7 +259,7 @@ ocotea_early_serial_map(void) gen550_init(0, &port); /* Purge TLB entry added in head_44x.S for early serial access */ - _tlbie(UART0_IO_BASE); + _tlbie(UART0_IO_BASE, 0); #endif port.membase = ioremap64(PPC440GX_UART1_ADDR, 8); diff --git a/arch/ppc/platforms/4xx/taishan.c b/arch/ppc/platforms/4xx/taishan.c index 888c492b4a4..f6a0c6650f3 100644 --- a/arch/ppc/platforms/4xx/taishan.c +++ b/arch/ppc/platforms/4xx/taishan.c @@ -316,7 +316,7 @@ taishan_early_serial_map(void) gen550_init(0, &port); /* Purge TLB entry added in head_44x.S for early serial access */ - _tlbie(UART0_IO_BASE); + _tlbie(UART0_IO_BASE, 0); #endif port.membase = ioremap64(PPC440GX_UART1_ADDR, 8); diff --git a/arch/ppc/syslib/i8259.c b/arch/ppc/syslib/i8259.c index 1e5a00a4b5f..559f27c6aef 100644 --- a/arch/ppc/syslib/i8259.c +++ b/arch/ppc/syslib/i8259.c @@ -127,6 +127,7 @@ static void i8259_unmask_irq(unsigned int irq_nr) static struct irq_chip i8259_pic = { .typename = " i8259 ", .mask = i8259_mask_irq, + .disable = i8259_mask_irq, .unmask = i8259_unmask_irq, .mask_ack = i8259_mask_and_ack_irq, }; diff --git a/arch/ppc/syslib/m8260_setup.c b/arch/ppc/syslib/m8260_setup.c index 15f0d732353..46588fa9438 100644 --- a/arch/ppc/syslib/m8260_setup.c +++ b/arch/ppc/syslib/m8260_setup.c @@ -25,6 +25,7 @@ #include <asm/machdep.h> #include <asm/bootinfo.h> #include <asm/time.h> +#include <asm/ppc_sys.h> #include "cpm2_pic.h" @@ -61,7 +62,7 @@ m8260_setup_arch(void) #endif identify_ppc_sys_by_name_and_id(BOARD_CHIP_NAME, - in_be32(CPM_MAP_ADDR + CPM_IMMR_OFFSET)); + in_be32((void *)CPM_MAP_ADDR + CPM_IMMR_OFFSET)); m82xx_board_setup(); } @@ -147,12 +148,12 @@ m8260_show_cpuinfo(struct seq_file *m) seq_printf(m, "vendor\t\t: %s\n" "machine\t\t: %s\n" "\n" - "mem size\t\t: 0x%08x\n" - "console baud\t\t: %d\n" + "mem size\t\t: 0x%08lx\n" + "console baud\t\t: %ld\n" "\n" - "core clock\t: %u MHz\n" - "CPM clock\t: %u MHz\n" - "bus clock\t: %u MHz\n", + "core clock\t: %lu MHz\n" + "CPM clock\t: %lu MHz\n" + "bus clock\t: %lu MHz\n", CPUINFO_VENDOR, CPUINFO_MACHINE, bp->bi_memsize, bp->bi_baudrate, bp->bi_intfreq / 1000000, bp->bi_cpmfreq / 1000000, bp->bi_busfreq / 1000000); diff --git a/drivers/macintosh/windfarm_core.c b/drivers/macintosh/windfarm_core.c index 516d943227e..075b4d99e35 100644 --- a/drivers/macintosh/windfarm_core.c +++ b/drivers/macintosh/windfarm_core.c @@ -94,7 +94,9 @@ static int wf_thread_func(void *data) DBG("wf: thread started\n"); set_freezable(); - while(!kthread_should_stop()) { + while (!kthread_should_stop()) { + try_to_freeze(); + if (time_after_eq(jiffies, next)) { wf_notify(WF_EVENT_TICK, NULL); if (wf_overtemp) { @@ -116,12 +118,6 @@ static int wf_thread_func(void *data) delay = next - jiffies; if (delay <= HZ) schedule_timeout_interruptible(delay); - - /* there should be no non-suspend signal, but oh well */ - if (signal_pending(current) && !try_to_freeze()) { - printk(KERN_WARNING "windfarm: thread got sigl !\n"); - break; - } } DBG("wf: thread stopped\n"); diff --git a/drivers/serial/uartlite.c b/drivers/serial/uartlite.c index dfef83f1496..a85f2d31a68 100644 --- a/drivers/serial/uartlite.c +++ b/drivers/serial/uartlite.c @@ -329,12 +329,14 @@ static struct uart_ops ulite_ops = { static void ulite_console_wait_tx(struct uart_port *port) { int i; + u8 val; - /* wait up to 10ms for the character(s) to be sent */ - for (i = 0; i < 10000; i++) { - if (readb(port->membase + ULITE_STATUS) & ULITE_STATUS_TXEMPTY) + /* Spin waiting for TX fifo to have space available */ + for (i = 0; i < 100000; i++) { + val = readb(port->membase + ULITE_STATUS); + if ((val & ULITE_STATUS_TXFULL) == 0) break; - udelay(1); + cpu_relax(); } } diff --git a/include/asm-powerpc/pgtable-ppc32.h b/include/asm-powerpc/pgtable-ppc32.h index 86a54a4a8a2..fea2d8ff1e7 100644 --- a/include/asm-powerpc/pgtable-ppc32.h +++ b/include/asm-powerpc/pgtable-ppc32.h @@ -11,6 +11,11 @@ extern unsigned long va_to_phys(unsigned long address); extern pte_t *va_to_pte(unsigned long address); extern unsigned long ioremap_bot, ioremap_base; + +#ifdef CONFIG_44x +extern int icache_44x_need_flush; +#endif + #endif /* __ASSEMBLY__ */ /* @@ -562,6 +567,10 @@ static inline unsigned long pte_update(pte_t *p, unsigned long clr, : "=&r" (old), "=&r" (tmp), "=m" (*p) : "r" (p), "r" (clr), "r" (set), "m" (*p) : "cc" ); +#ifdef CONFIG_44x + if ((old & _PAGE_USER) && (old & _PAGE_HWEXEC)) + icache_44x_need_flush = 1; +#endif return old; } #else @@ -582,6 +591,10 @@ static inline unsigned long long pte_update(pte_t *p, unsigned long clr, : "=&r" (old), "=&r" (tmp), "=m" (*p) : "r" (p), "r" ((unsigned long)(p) + 4), "r" (clr), "r" (set), "m" (*p) : "cc" ); +#ifdef CONFIG_44x + if ((old & _PAGE_USER) && (old & _PAGE_HWEXEC)) + icache_44x_need_flush = 1; +#endif return old; } #endif diff --git a/include/asm-powerpc/systbl.h b/include/asm-powerpc/systbl.h index cc6d8722825..11d5383b2f0 100644 --- a/include/asm-powerpc/systbl.h +++ b/include/asm-powerpc/systbl.h @@ -308,8 +308,8 @@ COMPAT_SYS_SPU(move_pages) SYSCALL_SPU(getcpu) COMPAT_SYS(epoll_pwait) COMPAT_SYS_SPU(utimensat) -COMPAT_SYS(fallocate) COMPAT_SYS_SPU(signalfd) COMPAT_SYS_SPU(timerfd) SYSCALL_SPU(eventfd) COMPAT_SYS_SPU(sync_file_range2) +COMPAT_SYS(fallocate) diff --git a/include/asm-powerpc/time.h b/include/asm-powerpc/time.h index f05895522f7..780f8264275 100644 --- a/include/asm-powerpc/time.h +++ b/include/asm-powerpc/time.h @@ -176,25 +176,31 @@ static inline unsigned int get_dec(void) #endif } +/* + * Note: Book E and 4xx processors differ from other PowerPC processors + * in when the decrementer generates its interrupt: on the 1 to 0 + * transition for Book E/4xx, but on the 0 to -1 transition for others. + */ static inline void set_dec(int val) { #if defined(CONFIG_40x) mtspr(SPRN_PIT, val); #elif defined(CONFIG_8xx_CPU6) - set_dec_cpu6(val); + set_dec_cpu6(val - 1); #else +#ifndef CONFIG_BOOKE + --val; +#endif #ifdef CONFIG_PPC_ISERIES - int cur_dec; - if (firmware_has_feature(FW_FEATURE_ISERIES) && get_lppaca()->shared_proc) { get_lppaca()->virtual_decr = val; - cur_dec = get_dec(); - if (cur_dec > val) + if (get_dec() > val) HvCall_setVirtualDecr(); - } else + return; + } #endif - mtspr(SPRN_DEC, val); + mtspr(SPRN_DEC, val); #endif /* not 40x or 8xx_CPU6 */ } diff --git a/include/asm-powerpc/tlbflush.h b/include/asm-powerpc/tlbflush.h index b6b036ccee3..e7b4c0d298a 100644 --- a/include/asm-powerpc/tlbflush.h +++ b/include/asm-powerpc/tlbflush.h @@ -1,5 +1,6 @@ #ifndef _ASM_POWERPC_TLBFLUSH_H #define _ASM_POWERPC_TLBFLUSH_H + /* * TLB flushing: * @@ -16,9 +17,6 @@ */ #ifdef __KERNEL__ -struct mm_struct; -struct vm_area_struct; - #if defined(CONFIG_4xx) || defined(CONFIG_8xx) || defined(CONFIG_FSL_BOOKE) /* * TLB flushing for software loaded TLB chips @@ -28,7 +26,9 @@ struct vm_area_struct; * specific tlbie's */ -extern void _tlbie(unsigned long address); +#include <linux/mm.h> + +extern void _tlbie(unsigned long address, unsigned int pid); #if defined(CONFIG_40x) || defined(CONFIG_8xx) #define _tlbia() asm volatile ("tlbia; sync" : : : "memory") @@ -44,13 +44,13 @@ static inline void flush_tlb_mm(struct mm_struct *mm) static inline void flush_tlb_page(struct vm_area_struct *vma, unsigned long vmaddr) { - _tlbie(vmaddr); + _tlbie(vmaddr, vma->vm_mm->context.id); } static inline void flush_tlb_page_nohash(struct vm_area_struct *vma, unsigned long vmaddr) { - _tlbie(vmaddr); + _tlbie(vmaddr, vma->vm_mm->context.id); } static inline void flush_tlb_range(struct vm_area_struct *vma, |