diff options
| -rw-r--r-- | arch/arm/mach-davinci/include/mach/nand.h | 3 | ||||
| -rw-r--r-- | drivers/mtd/nand/davinci_nand.c | 60 |
2 files changed, 25 insertions, 38 deletions
diff --git a/arch/arm/mach-davinci/include/mach/nand.h b/arch/arm/mach-davinci/include/mach/nand.h index b5893f035fe..025151049f0 100644 --- a/arch/arm/mach-davinci/include/mach/nand.h +++ b/arch/arm/mach-davinci/include/mach/nand.h @@ -80,6 +80,9 @@ struct davinci_nand_pdata { /* platform_data */ /* Main and mirror bbt descriptor overrides */ struct nand_bbt_descr *bbt_td; struct nand_bbt_descr *bbt_md; + + /* Access timings */ + struct davinci_aemif_timing *timing; }; #endif /* __ARCH_ARM_DAVINCI_NAND_H */ diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c index 8e2d56c3681..8beb0d0233b 100644 --- a/drivers/mtd/nand/davinci_nand.c +++ b/drivers/mtd/nand/davinci_nand.c @@ -75,6 +75,8 @@ struct davinci_nand_info { uint32_t mask_cle; uint32_t core_chipsel; + + struct davinci_aemif_timing *timing; }; static DEFINE_SPINLOCK(davinci_nand_lock); @@ -479,36 +481,6 @@ static int nand_davinci_dev_ready(struct mtd_info *mtd) return davinci_nand_readl(info, NANDFSR_OFFSET) & BIT(0); } -static void __init nand_dm6446evm_flash_init(struct davinci_nand_info *info) -{ - uint32_t regval, a1cr; - - /* - * NAND FLASH timings @ PLL1 == 459 MHz - * - AEMIF.CLK freq = PLL1/6 = 459/6 = 76.5 MHz - * - AEMIF.CLK period = 1/76.5 MHz = 13.1 ns - */ - regval = 0 - | (0 << 31) /* selectStrobe */ - | (0 << 30) /* extWait (never with NAND) */ - | (1 << 26) /* writeSetup 10 ns */ - | (3 << 20) /* writeStrobe 40 ns */ - | (1 << 17) /* writeHold 10 ns */ - | (0 << 13) /* readSetup 10 ns */ - | (3 << 7) /* readStrobe 60 ns */ - | (0 << 4) /* readHold 10 ns */ - | (3 << 2) /* turnAround ?? ns */ - | (0 << 0) /* asyncSize 8-bit bus */ - ; - a1cr = davinci_nand_readl(info, A1CR_OFFSET); - if (a1cr != regval) { - dev_dbg(info->dev, "Warning: NAND config: Set A1CR " \ - "reg to 0x%08x, was 0x%08x, should be done by " \ - "bootloader.\n", regval, a1cr); - davinci_nand_writel(info, A1CR_OFFSET, regval); - } -} - /*----------------------------------------------------------------------*/ /* An ECC layout for using 4-bit ECC with small-page flash, storing @@ -612,6 +584,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev) info->chip.options = pdata->options; info->chip.bbt_td = pdata->bbt_td; info->chip.bbt_md = pdata->bbt_md; + info->timing = pdata->timing; info->ioaddr = (uint32_t __force) vaddr; @@ -689,15 +662,25 @@ static int __init nand_davinci_probe(struct platform_device *pdev) goto err_clk_enable; } - /* EMIF timings should normally be set by the boot loader, - * especially after boot-from-NAND. The *only* reason to - * have this special casing for the DM6446 EVM is to work - * with boot-from-NOR ... with CS0 manually re-jumpered - * (after startup) so it addresses the NAND flash, not NOR. - * Even for dev boards, that's unusually rude... + /* + * Setup Async configuration register in case we did not boot from + * NAND and so bootloader did not bother to set it up. */ - if (machine_is_davinci_evm()) - nand_dm6446evm_flash_init(info); + val = davinci_nand_readl(info, A1CR_OFFSET + info->core_chipsel * 4); + + /* Extended Wait is not valid and Select Strobe mode is not used */ + val &= ~(ACR_ASIZE_MASK | ACR_EW_MASK | ACR_SS_MASK); + if (info->chip.options & NAND_BUSWIDTH_16) + val |= 0x1; + + davinci_nand_writel(info, A1CR_OFFSET + info->core_chipsel * 4, val); + + ret = davinci_aemif_setup_timing(info->timing, info->base, + info->core_chipsel); + if (ret < 0) { + dev_dbg(&pdev->dev, "NAND timing values setup fail\n"); + goto err_timing; + } spin_lock_irq(&davinci_nand_lock); @@ -810,6 +793,7 @@ syndrome_done: return 0; err_scan: +err_timing: clk_disable(info->clk); err_clk_enable: |