diff options
| -rw-r--r-- | Documentation/hwmon/lm90 | 23 | ||||
| -rw-r--r-- | drivers/hwmon/Kconfig | 8 | ||||
| -rw-r--r-- | drivers/hwmon/lm90.c | 22 |
3 files changed, 36 insertions, 17 deletions
diff --git a/Documentation/hwmon/lm90 b/Documentation/hwmon/lm90 index fa475c0a48a..aa820aca795 100644 --- a/Documentation/hwmon/lm90 +++ b/Documentation/hwmon/lm90 @@ -32,6 +32,16 @@ Supported chips: Addresses scanned: I2C 0x4c and 0x4d Datasheet: Publicly available at the ON Semiconductor website http://www.onsemi.com/PowerSolutions/product.do?id=ADT7461 + * Analog Devices ADT7461A + Prefix: 'adt7461a' + Addresses scanned: I2C 0x4c and 0x4d + Datasheet: Publicly available at the ON Semiconductor website + http://www.onsemi.com/PowerSolutions/product.do?id=ADT7461A + * ON Semiconductor NCT1008 + Prefix: 'nct1008' + Addresses scanned: I2C 0x4c and 0x4d + Datasheet: Publicly available at the ON Semiconductor website + http://www.onsemi.com/PowerSolutions/product.do?id=NCT1008 * Maxim MAX6646 Prefix: 'max6646' Addresses scanned: I2C 0x4d @@ -149,7 +159,7 @@ ADM1032: * ALERT is triggered by open remote sensor. * SMBus PEC support for Write Byte and Receive Byte transactions. -ADT7461: +ADT7461, ADT7461A, NCT1008: * Extended temperature range (breaks compatibility) * Lower resolution for remote temperature @@ -205,11 +215,12 @@ SMBus Alert Support This driver has basic support for SMBus alert. When an alert is received, the status register is read and the faulty temperature channel is logged. -The Analog Devices chips (ADM1032 and ADT7461) do not implement the SMBus -alert protocol properly so additional care is needed: the ALERT output is -disabled when an alert is received, and is re-enabled only when the alarm -is gone. Otherwise the chip would block alerts from other chips in the bus -as long as the alarm is active. +The Analog Devices chips (ADM1032, ADT7461 and ADT7461A) and ON +Semiconductor chips (NCT1008) do not implement the SMBus alert protocol +properly so additional care is needed: the ALERT output is disabled when +an alert is received, and is re-enabled only when the alarm is gone. +Otherwise the chip would block alerts from other chips in the bus as long +as the alarm is active. PEC Support ----------- diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 060ef632787..92d02512bcd 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -618,10 +618,10 @@ config SENSORS_LM90 depends on I2C help If you say yes here you get support for National Semiconductor LM90, - LM86, LM89 and LM99, Analog Devices ADM1032 and ADT7461, Maxim - MAX6646, MAX6647, MAX6648, MAX6649, MAX6657, MAX6658, MAX6659, - MAX6680, MAX6681, MAX6692, MAX6695, MAX6696, and Winbond/Nuvoton - W83L771W/G/AWG/ASG sensor chips. + LM86, LM89 and LM99, Analog Devices ADM1032, ADT7461, and ADT7461A, + Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6657, MAX6658, MAX6659, + MAX6680, MAX6681, MAX6692, MAX6695, MAX6696, ON Semiconductor NCT1008, + and Winbond/Nuvoton W83L771W/G/AWG/ASG sensor chips. This driver can also be built as a module. If so, the module will be called lm90. diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c index c43b4e9f96a..2f94f950480 100644 --- a/drivers/hwmon/lm90.c +++ b/drivers/hwmon/lm90.c @@ -49,10 +49,10 @@ * chips, but support three temperature sensors instead of two. MAX6695 * and MAX6696 only differ in the pinout so they can be treated identically. * - * This driver also supports the ADT7461 chip from Analog Devices. - * It's supported in both compatibility and extended mode. It is mostly - * compatible with LM90 except for a data format difference for the - * temperature value registers. + * This driver also supports ADT7461 and ADT7461A from Analog Devices as well as + * NCT1008 from ON Semiconductor. The chips are supported in both compatibility + * and extended mode. They are mostly compatible with LM90 except for a data + * format difference for the temperature value registers. * * Since the LM90 was the first chipset supported by this driver, most * comments will refer to this chipset, but are actually general and @@ -88,9 +88,10 @@ * Addresses to scan * Address is fully defined internally and cannot be changed except for * MAX6659, MAX6680 and MAX6681. - * LM86, LM89, LM90, LM99, ADM1032, ADM1032-1, ADT7461, MAX6649, MAX6657, - * MAX6658 and W83L771 have address 0x4c. - * ADM1032-2, ADT7461-2, LM89-1, LM99-1 and MAX6646 have address 0x4d. + * LM86, LM89, LM90, LM99, ADM1032, ADM1032-1, ADT7461, ADT7461A, MAX6649, + * MAX6657, MAX6658, NCT1008 and W83L771 have address 0x4c. + * ADM1032-2, ADT7461-2, ADT7461A-2, LM89-1, LM99-1, MAX6646, and NCT1008D + * have address 0x4d. * MAX6647 has address 0x4e. * MAX6659 can have address 0x4c, 0x4d or 0x4e. * MAX6680 and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, @@ -174,6 +175,7 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680, static const struct i2c_device_id lm90_id[] = { { "adm1032", adm1032 }, { "adt7461", adt7461 }, + { "adt7461a", adt7461 }, { "lm90", lm90 }, { "lm86", lm86 }, { "lm89", lm86 }, @@ -188,6 +190,7 @@ static const struct i2c_device_id lm90_id[] = { { "max6681", max6680 }, { "max6695", max6696 }, { "max6696", max6696 }, + { "nct1008", adt7461 }, { "w83l771", w83l771 }, { } }; @@ -1153,6 +1156,11 @@ static int lm90_detect(struct i2c_client *new_client, && (reg_config1 & 0x1B) == 0x00 && reg_convrate <= 0x0A) { name = "adt7461"; + } else + if (chip_id == 0x57 /* ADT7461A, NCT1008 */ + && (reg_config1 & 0x1B) == 0x00 + && reg_convrate <= 0x0A) { + name = "adt7461a"; } } else if (man_id == 0x4D) { /* Maxim */ |