diff options
581 files changed, 11245 insertions, 7973 deletions
@@ -1194,15 +1194,9 @@ S: Brecksville, OH 44141-1334 S: USA N: Tristan Greaves -E: Tristan.Greaves@icl.com -E: tmg296@ecs.soton.ac.uk -W: http://www.ecs.soton.ac.uk/~tmg296 +E: tristan@extricate.org +W: http://www.extricate.org/ D: Miscellaneous ipv4 sysctl patches -S: 15 Little Mead -S: Denmead -S: Hampshire -S: PO7 6HS -S: United Kingdom N: Michael A. Griffith E: grif@cs.ucr.edu diff --git a/Documentation/HOWTO b/Documentation/HOWTO index 6c9e746267d..915ae8c986c 100644 --- a/Documentation/HOWTO +++ b/Documentation/HOWTO @@ -603,7 +603,8 @@ start exactly where you are now. ---------- -Thanks to Paolo Ciarrocchi who allowed the "Development Process" section +Thanks to Paolo Ciarrocchi who allowed the "Development Process" +(http://linux.tar.bz/articles/2.6-development_process) section to be based on text he had written, and to Randy Dunlap and Gerrit Huizenga for some of the list of things you should and should not say. Also thanks to Pat Mochel, Hanna Linder, Randy Dunlap, Kay Sievers, diff --git a/Documentation/networking/operstates.txt b/Documentation/networking/operstates.txt new file mode 100644 index 00000000000..4a21d9bb836 --- /dev/null +++ b/Documentation/networking/operstates.txt @@ -0,0 +1,161 @@ + +1. Introduction + +Linux distinguishes between administrative and operational state of an +interface. Admininstrative state is the result of "ip link set dev +<dev> up or down" and reflects whether the administrator wants to use +the device for traffic. + +However, an interface is not usable just because the admin enabled it +- ethernet requires to be plugged into the switch and, depending on +a site's networking policy and configuration, an 802.1X authentication +to be performed before user data can be transferred. Operational state +shows the ability of an interface to transmit this user data. + +Thanks to 802.1X, userspace must be granted the possibility to +influence operational state. To accommodate this, operational state is +split into two parts: Two flags that can be set by the driver only, and +a RFC2863 compatible state that is derived from these flags, a policy, +and changeable from userspace under certain rules. + + +2. Querying from userspace + +Both admin and operational state can be queried via the netlink +operation RTM_GETLINK. It is also possible to subscribe to RTMGRP_LINK +to be notified of updates. This is important for setting from userspace. + +These values contain interface state: + +ifinfomsg::if_flags & IFF_UP: + Interface is admin up +ifinfomsg::if_flags & IFF_RUNNING: + Interface is in RFC2863 operational state UP or UNKNOWN. This is for + backward compatibility, routing daemons, dhcp clients can use this + flag to determine whether they should use the interface. +ifinfomsg::if_flags & IFF_LOWER_UP: + Driver has signaled netif_carrier_on() +ifinfomsg::if_flags & IFF_DORMANT: + Driver has signaled netif_dormant_on() + +These interface flags can also be queried without netlink using the +SIOCGIFFLAGS ioctl. + +TLV IFLA_OPERSTATE + +contains RFC2863 state of the interface in numeric representation: + +IF_OPER_UNKNOWN (0): + Interface is in unknown state, neither driver nor userspace has set + operational state. Interface must be considered for user data as + setting operational state has not been implemented in every driver. +IF_OPER_NOTPRESENT (1): + Unused in current kernel (notpresent interfaces normally disappear), + just a numerical placeholder. +IF_OPER_DOWN (2): + Interface is unable to transfer data on L1, f.e. ethernet is not + plugged or interface is ADMIN down. +IF_OPER_LOWERLAYERDOWN (3): + Interfaces stacked on an interface that is IF_OPER_DOWN show this + state (f.e. VLAN). +IF_OPER_TESTING (4): + Unused in current kernel. +IF_OPER_DORMANT (5): + Interface is L1 up, but waiting for an external event, f.e. for a + protocol to establish. (802.1X) +IF_OPER_UP (6): + Interface is operational up and can be used. + +This TLV can also be queried via sysfs. + +TLV IFLA_LINKMODE + +contains link policy. This is needed for userspace interaction +described below. + +This TLV can also be queried via sysfs. + + +3. Kernel driver API + +Kernel drivers have access to two flags that map to IFF_LOWER_UP and +IFF_DORMANT. These flags can be set from everywhere, even from +interrupts. It is guaranteed that only the driver has write access, +however, if different layers of the driver manipulate the same flag, +the driver has to provide the synchronisation needed. + +__LINK_STATE_NOCARRIER, maps to !IFF_LOWER_UP: + +The driver uses netif_carrier_on() to clear and netif_carrier_off() to +set this flag. On netif_carrier_off(), the scheduler stops sending +packets. The name 'carrier' and the inversion are historical, think of +it as lower layer. + +netif_carrier_ok() can be used to query that bit. + +__LINK_STATE_DORMANT, maps to IFF_DORMANT: + +Set by the driver to express that the device cannot yet be used +because some driver controlled protocol establishment has to +complete. Corresponding functions are netif_dormant_on() to set the +flag, netif_dormant_off() to clear it and netif_dormant() to query. + +On device allocation, networking core sets the flags equivalent to +netif_carrier_ok() and !netif_dormant(). + + +Whenever the driver CHANGES one of these flags, a workqueue event is +scheduled to translate the flag combination to IFLA_OPERSTATE as +follows: + +!netif_carrier_ok(): + IF_OPER_LOWERLAYERDOWN if the interface is stacked, IF_OPER_DOWN + otherwise. Kernel can recognise stacked interfaces because their + ifindex != iflink. + +netif_carrier_ok() && netif_dormant(): + IF_OPER_DORMANT + +netif_carrier_ok() && !netif_dormant(): + IF_OPER_UP if userspace interaction is disabled. Otherwise + IF_OPER_DORMANT with the possibility for userspace to initiate the + IF_OPER_UP transition afterwards. + + +4. Setting from userspace + +Applications have to use the netlink interface to influence the +RFC2863 operational state of an interface. Setting IFLA_LINKMODE to 1 +via RTM_SETLINK instructs the kernel that an interface should go to +IF_OPER_DORMANT instead of IF_OPER_UP when the combination +netif_carrier_ok() && !netif_dormant() is set by the +driver. Afterwards, the userspace application can set IFLA_OPERSTATE +to IF_OPER_DORMANT or IF_OPER_UP as long as the driver does not set +netif_carrier_off() or netif_dormant_on(). Changes made by userspace +are multicasted on the netlink group RTMGRP_LINK. + +So basically a 802.1X supplicant interacts with the kernel like this: + +-subscribe to RTMGRP_LINK +-set IFLA_LINKMODE to 1 via RTM_SETLINK +-query RTM_GETLINK once to get initial state +-if initial flags are not (IFF_LOWER_UP && !IFF_DORMANT), wait until + netlink multicast signals this state +-do 802.1X, eventually abort if flags go down again +-send RTM_SETLINK to set operstate to IF_OPER_UP if authentication + succeeds, IF_OPER_DORMANT otherwise +-see how operstate and IFF_RUNNING is echoed via netlink multicast +-set interface back to IF_OPER_DORMANT if 802.1X reauthentication + fails +-restart if kernel changes IFF_LOWER_UP or IFF_DORMANT flag + +if supplicant goes down, bring back IFLA_LINKMODE to 0 and +IFLA_OPERSTATE to a sane value. + +A routing daemon or dhcp client just needs to care for IFF_RUNNING or +waiting for operstate to go IF_OPER_UP/IF_OPER_UNKNOWN before +considering the interface / querying a DHCP address. + + +For technical questions and/or comments please e-mail to Stefan Rompf +(stefan at loplof.de). diff --git a/Documentation/pci.txt b/Documentation/pci.txt index 711210b38f5..66bbbf1d1ef 100644 --- a/Documentation/pci.txt +++ b/Documentation/pci.txt @@ -259,7 +259,17 @@ on the bus need to be capable of doing it, so this is something which needs to be handled by platform and generic code, not individual drivers. -8. Obsolete functions +8. Vendor and device identifications +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +For the future, let's avoid adding device ids to include/linux/pci_ids.h. + +PCI_VENDOR_ID_xxx for vendors, and a hex constant for device ids. + +Rationale: PCI_VENDOR_ID_xxx constants are re-used, but device ids are not. + Further, device ids are arbitrary hex numbers, normally used only in a + single location, the pci_device_id table. + +9. Obsolete functions ~~~~~~~~~~~~~~~~~~~~~ There are several functions which you might come across when trying to port an old driver to the new PCI interface. They are no longer present diff --git a/Documentation/power/video.txt b/Documentation/power/video.txt index d18a57d1a53..43a889f8f08 100644 --- a/Documentation/power/video.txt +++ b/Documentation/power/video.txt @@ -140,7 +140,7 @@ IBM TP T41p s3_bios (2), switch to X after resume IBM TP T42 s3_bios (2) IBM ThinkPad T42p (2373-GTG) s3_bios (2) IBM TP X20 ??? (*) -IBM TP X30 s3_bios (2) +IBM TP X30 s3_bios, s3_mode (4) IBM TP X31 / Type 2672-XXH none (1), use radeontool (http://fdd.com/software/radeon/) to turn off backlight. IBM TP X32 none (1), but backlight is on and video is trashed after long suspend. s3_bios,s3_mode (4) works too. Perhaps that gets better results? IBM Thinkpad X40 Type 2371-7JG s3_bios,s3_mode (4) diff --git a/Documentation/scsi/ChangeLog.megaraid b/Documentation/scsi/ChangeLog.megaraid index 09f6300eda4..c173806c91f 100644 --- a/Documentation/scsi/ChangeLog.megaraid +++ b/Documentation/scsi/ChangeLog.megaraid @@ -1,3 +1,28 @@ +Release Date : Mon Apr 11 12:27:22 EST 2006 - Seokmann Ju <sju@lsil.com> +Current Version : 2.20.4.8 (scsi module), 2.20.2.6 (cmm module) +Older Version : 2.20.4.7 (scsi module), 2.20.2.6 (cmm module) + +1. Fixed a bug in megaraid_reset_handler(). + Customer reported "Unable to handle kernel NULL pointer dereference + at virtual address 00000000" when system goes to reset condition + for some reason. It happened randomly. + Root Cause: in the megaraid_reset_handler(), there is possibility not + returning pending packets in the pend_list if there are multiple + pending packets. + Fix: Made the change in the driver so that it will return all packets + in the pend_list. + +2. Added change request. + As found in the following URL, rmb() only didn't help the + problem. I had to increase the loop counter to 0xFFFFFF. (6 F's) + http://marc.theaimsgroup.com/?l=linux-scsi&m=110971060502497&w=2 + + I attached a patch for your reference, too. + Could you check and get this fix in your driver? + + Best Regards, + Jun'ichi Nomura + Release Date : Fri Nov 11 12:27:22 EST 2005 - Seokmann Ju <sju@lsil.com> Current Version : 2.20.4.7 (scsi module), 2.20.2.6 (cmm module) Older Version : 2.20.4.6 (scsi module), 2.20.2.6 (cmm module) diff --git a/Documentation/sound/alsa/Audiophile-Usb.txt b/Documentation/sound/alsa/Audiophile-Usb.txt index 4692c8e77dc..b535c2a198f 100644 --- a/Documentation/sound/alsa/Audiophile-Usb.txt +++ b/Documentation/sound/alsa/Audiophile-Usb.txt @@ -1,4 +1,4 @@ - Guide to using M-Audio Audiophile USB with ALSA and Jack v1.2 + Guide to using M-Audio Audiophile USB with ALSA and Jack v1.3 ======================================================== Thibault Le Meur <Thibault.LeMeur@supelec.fr> @@ -22,16 +22,16 @@ The device has 4 audio interfaces, and 2 MIDI ports: * Midi In (Mi) * Midi Out (Mo) -The internal DAC/ADC has the following caracteristics: +The internal DAC/ADC has the following characteristics: * sample depth of 16 or 24 bits * sample rate from 8kHz to 96kHz -* Two ports can't use different sample depths at the same time.Moreover, the +* Two ports can't use different sample depths at the same time. Moreover, the Audiophile USB documentation gives the following Warning: "Please exit any audio application running before switching between bit depths" Due to the USB 1.1 bandwidth limitation, a limited number of interfaces can be activated at the same time depending on the audio mode selected: - * 16-bit/48kHz ==> 4 channels in/ 4 channels out + * 16-bit/48kHz ==> 4 channels in/4 channels out - Ai+Ao+Di+Do * 24-bit/48kHz ==> 4 channels in/2 channels out, or 2 channels in/4 channels out @@ -41,8 +41,8 @@ activated at the same time depending on the audio mode selected: Important facts about the Digital interface: -------------------------------------------- - * The Do port additionnaly supports surround-encoded AC-3 and DTS passthrough, -though I haven't tested it under linux + * The Do port additionally supports surround-encoded AC-3 and DTS passthrough, +though I haven't tested it under Linux - Note that in this setup only the Do interface can be enabled * Apart from recording an audio digital stream, enabling the Di port is a way to synchronize the device to an external sample clock @@ -60,24 +60,23 @@ synchronization error (for instance sound played at an odd sample rate) The Audiophile USB MIDI ports will be automatically supported once the following modules have been loaded: * snd-usb-audio - * snd-seq * snd-seq-midi -No additionnal setting is required. +No additional setting is required. 2.2 - Audio ports ----------------- Audio functions of the Audiophile USB device are handled by the snd-usb-audio module. This module can work in a default mode (without any device-specific -parameter), or in an advanced mode with the device-specific parameter called +parameter), or in an "advanced" mode with the device-specific parameter called "device_setup". 2.2.1 - Default Alsa driver mode -The default behaviour of the snd-usb-audio driver is to parse the device +The default behavior of the snd-usb-audio driver is to parse the device capabilities at startup and enable all functions inside the device (including -all ports at any sample rates and any sample depths supported). This approach +all ports at any supported sample rates and sample depths). This approach has the advantage to let the driver easily switch from sample rates/depths automatically according to the need of the application claiming the device. @@ -114,9 +113,9 @@ gain). For people having this problem, the snd-usb-audio module has a new module parameter called "device_setup". -2.2.2.1 - Initializing the working mode of the Audiohile USB +2.2.2.1 - Initializing the working mode of the Audiophile USB -As far as the Audiohile USB device is concerned, this value let the user +As far as the Audiophile USB device is concerned, this value let the user specify: * the sample depth * the sample rate @@ -174,20 +173,20 @@ The parameter can be given: IMPORTANT NOTE WHEN SWITCHING CONFIGURATION: ------------------------------------------- - * You may need to _first_ intialize the module with the correct device_setup + * You may need to _first_ initialize the module with the correct device_setup parameter and _only_after_ turn on the Audiophile USB device * This is especially true when switching the sample depth: - - first trun off the device - - de-register the snd-usb-audio module - - change the device_setup parameter (by either manually reprobing the module - or changing modprobe.conf) + - first turn off the device + - de-register the snd-usb-audio module (modprobe -r) + - change the device_setup parameter by changing the device_setup + option in /etc/modprobe.conf - turn on the device 2.2.2.3 - Audiophile USB's device_setup structure If you want to understand the device_setup magic numbers for the Audiophile USB, you need some very basic understanding of binary computation. However, -this is not required to use the parameter and you may skip thi section. +this is not required to use the parameter and you may skip this section. The device_setup is one byte long and its structure is the following: @@ -231,11 +230,11 @@ Caution: 2.2.3 - USB implementation details for this device -You may safely skip this section if you're not interrested in driver +You may safely skip this section if you're not interested in driver development. -This section describes some internals aspect of the device and summarize the -data I got by usb-snooping the windows and linux drivers. +This section describes some internal aspects of the device and summarize the +data I got by usb-snooping the windows and Linux drivers. The M-Audio Audiophile USB has 7 USB Interfaces: a "USB interface": @@ -277,9 +276,9 @@ Here is a short description of the AltSettings capabilities: - 16-bit depth, 8-48kHz sample mode - Synch playback (Do), audio format type III IEC1937_AC-3 -In order to ensure a correct intialization of the device, the driver +In order to ensure a correct initialization of the device, the driver _must_know_ how the device will be used: - * if DTS is choosen, only Interface 2 with AltSet nb.6 must be + * if DTS is chosen, only Interface 2 with AltSet nb.6 must be registered * if 96KHz only AltSets nb.1 of each interface must be selected * if samples are using 24bits/48KHz then AltSet 2 must me used if @@ -290,7 +289,7 @@ _must_know_ how the device will be used: is not connected When device_setup is given as a parameter to the snd-usb-audio module, the -parse_audio_enpoint function uses a quirk called +parse_audio_endpoints function uses a quirk called "audiophile_skip_setting_quirk" in order to prevent AltSettings not corresponding to device_setup from being registered in the driver. @@ -317,9 +316,8 @@ However you may see the following warning message: using the "default" ALSA device. This is less efficient than it could be. Consider using a hardware device instead rather than using the plug layer." - 3.2 - Patching alsa to use direct pcm device -------------------------------------------- +-------------------------------------------- A patch for Jack by Andreas Steinmetz adds support for Big Endian devices. However it has not been included in the CVS tree. @@ -331,3 +329,32 @@ After having applied the patch you can run jackd with the following command line: % jackd -R -dalsa -Phw:1,0 -r48000 -p128 -n2 -D -Chw:1,1 +3.2 - Getting 2 input and/or output interfaces in Jack +------------------------------------------------------ + +As you can see, starting the Jack server this way will only enable 1 stereo +input (Di or Ai) and 1 stereo output (Ao or Do). + +This is due to the following restrictions: +* Jack can only open one capture device and one playback device at a time +* The Audiophile USB is seen as 2 (or three) Alsa devices: hw:1,0, hw:1,1 + (and optionally hw:1,2) +If you want to get Ai+Di and/or Ao+Do support with Jack, you would need to +combine the Alsa devices into one logical "complex" device. + +If you want to give it a try, I recommend reading the information from +this page: http://www.sound-man.co.uk/linuxaudio/ice1712multi.html +It is related to another device (ice1712) but can be adapted to suit +the Audiophile USB. + +Enabling multiple Audiophile USB interfaces for Jackd will certainly require: +* patching Jack with the previously mentioned "Big Endian" patch +* patching Jackd with the MMAP_COMPLEX patch (see the ice1712 page) +* patching the alsa-lib/src/pcm/pcm_multi.c file (see the ice1712 page) +* define a multi device (combination of hw:1,0 and hw:1,1) in your .asoundrc + file +* start jackd with this device + +I had no success in testing this for now, but this may be due to my OS +configuration. If you have any success with this kind of setup, please +drop me an email. diff --git a/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl b/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl index 68eeebc17ff..1faf76383ba 100644 --- a/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl +++ b/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl @@ -1172,7 +1172,7 @@ } /* PCI IDs */ - static struct pci_device_id snd_mychip_ids[] = { + static struct pci_device_id snd_mychip_ids[] __devinitdata = { { PCI_VENDOR_ID_FOO, PCI_DEVICE_ID_BAR, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, .... @@ -1565,7 +1565,7 @@ <informalexample> <programlisting> <![CDATA[ - static struct pci_device_id snd_mychip_ids[] = { + static struct pci_device_id snd_mychip_ids[] __devinitdata = { { PCI_VENDOR_ID_FOO, PCI_DEVICE_ID_BAR, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, .... diff --git a/MAINTAINERS b/MAINTAINERS index f4bd145c007..c676253ef40 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1498,10 +1498,11 @@ L: netdev@vger.kernel.org S: Maintained IRDA SUBSYSTEM -P: Jean Tourrilhes +P: Samuel Ortiz +M: samuel@sortiz.org L: irda-users@lists.sourceforge.net (subscribers-only) W: http://irda.sourceforge.net/ -S: Odd Fixes +S: Maintained ISAPNP P: Jaroslav Kysela @@ -1,7 +1,7 @@ VERSION = 2 PATCHLEVEL = 6 SUBLEVEL = 17 -EXTRAVERSION =-rc3 +EXTRAVERSION =-rc4 NAME=Sliding Snow Leopard # *DOCUMENTATION* @@ -344,16 +344,14 @@ scripts_basic: scripts/basic/%: scripts_basic ; PHONY += outputmakefile -# outputmakefile generate a Makefile to be placed in output directory, if -# using a seperate output directory. This allows convinient use -# of make in output directory +# outputmakefile generates a Makefile in the output directory, if using a +# separate output directory. This allows convenient use of make in the +# output directory. outputmakefile: - $(Q)if test ! $(srctree) -ef $(objtree); then \ - $(CONFIG_SHELL) $(srctree)/scripts/mkmakefile \ - $(srctree) $(objtree) $(VERSION) $(PATCHLEVEL) \ - > $(objtree)/Makefile; \ - echo ' GEN $(objtree)/Makefile'; \ - fi +ifneq ($(KBUILD_SRC),) + $(Q)$(CONFIG_SHELL) $(srctree)/scripts/mkmakefile \ + $(srctree) $(objtree) $(VERSION) $(PATCHLEVEL) +endif # To make sure we do not include .config for any of the *config targets # catch them early, and hand them over to scripts/kconfig/Makefile @@ -796,8 +794,8 @@ prepare2: prepare3 outputmakefile prepare1: prepare2 include/linux/version.h include/asm \ include/config/MARKER ifneq ($(KBUILD_MODULES),) - $(Q)rm -rf $(MODVERDIR) $(Q)mkdir -p $(MODVERDIR) + $(Q)rm -f $(MODVERDIR)/* endif archprepare: prepare1 scripts_basic @@ -1086,8 +1084,8 @@ else # KBUILD_EXTMOD KBUILD_MODULES := 1 PHONY += crmodverdir crmodverdir: - $(Q)rm -rf $(MODVERDIR) $(Q)mkdir -p $(MODVERDIR) + $(Q)rm -f $(MODVERDIR)/* PHONY += $(objtree)/Module.symvers $(objtree)/Module.symvers: diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 1dbf6ddb300..08b7cc900ca 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -150,8 +150,6 @@ config ARCH_IOP3XX config ARCH_IXP4XX bool "IXP4xx-based" - select DMABOUNCE - select PCI help Support for Intel's IXP4XX (XScale) family of processors. diff --git a/arch/arm/boot/compressed/misc.c b/arch/arm/boot/compressed/misc.c index 0af3772efcb..ace3fb5835d 100644 --- a/arch/arm/boot/compressed/misc.c +++ b/arch/arm/boot/compressed/misc.c @@ -38,10 +38,10 @@ static void icedcc_putc(int ch) if (--i < 0) return; - asm("mrc p14, 0, %0, c0, c0, 0" : "=r" (status)); + asm volatile ("mrc p14, 0, %0, c0, c0, 0" : "=r" (status)); } while (status & 2); - asm("mcr p15, 0, %0, c1, c0, 0" : : "r" (ch)); + asm("mcr p14, 0, %0, c1, c0, 0" : : "r" (ch)); } #define putc(ch) icedcc_putc(ch) diff --git a/arch/arm/configs/collie_defconfig b/arch/arm/configs/collie_defconfig index c9aa878e610..074c47a4fb2 100644 --- a/arch/arm/configs/collie_defconfig +++ b/arch/arm/configs/collie_defconfig @@ -1,21 +1,21 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.14-rc3 -# Sun Oct 9 16:55:14 2005 +# Linux kernel version: 2.6.17-rc1 +# Fri Apr 14 19:09:52 2006 # CONFIG_ARM=y CONFIG_MMU=y -CONFIG_UID16=y CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ARCH_MTD_XIP=y +CONFIG_VECTORS_BASE=0xffff0000 # # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y -CONFIG_LOCK_KERNEL=y CONFIG_INIT_ENV_ARG_LIMIT=32 # @@ -23,45 +23,58 @@ CONFIG_INIT_ENV_ARG_LIMIT=32 # CONFIG_LOCALVERSION="" CONFIG_LOCALVERSION_AUTO=y -CONFIG_SWAP=y +# CONFIG_SWAP is not set CONFIG_SYSVIPC=y # CONFIG_POSIX_MQUEUE is not set -CONFIG_BSD_PROCESS_ACCT=y -# CONFIG_BSD_PROCESS_ACCT_V3 is not set +# CONFIG_BSD_PROCESS_ACCT is not set CONFIG_SYSCTL=y # CONFIG_AUDIT is not set -CONFIG_HOTPLUG=y -CONFIG_KOBJECT_UEVENT=y # CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" +CONFIG_UID16=y +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y -CONFIG_BASE_FULL=y +CONFIG_ELF_CORE=y +# CONFIG_BASE_FULL is not set CONFIG_FUTEX=y -CONFIG_EPOLL=y -# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +# CONFIG_EPOLL is not set CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 +# CONFIG_SLAB is not set +CONFIG_DOUBLEFAULT=y # CONFIG_TINY_SHMEM is not set -CONFIG_BASE_SMALL=0 +CONFIG_BASE_SMALL=1 +CONFIG_SLOB=y +CONFIG_OBSOLETE_INTERMODULE=y # # Loadable module support # -CONFIG_MODULES=y -CONFIG_MODULE_UNLOAD=y -CONFIG_MODULE_FORCE_UNLOAD=y -CONFIG_OBSOLETE_MODPARM=y -CONFIG_MODVERSIONS=y -# CONFIG_MODULE_SRCVERSION_ALL is not set -CONFIG_KMOD=y +# CONFIG_MODULES is not set + +# +# Block layer +# +# CONFIG_BLK_DEV_IO_TRACE is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" # # System Type @@ -70,11 +83,13 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP23XX is not set # CONFIG_ARCH_L7200 is not set # CONFIG_ARCH_PXA is not set # CONFIG_ARCH_RPC is not set @@ -84,9 +99,11 @@ CONFIG_ARCH_SA1100=y # CONFIG_ARCH_LH7A40X is not set # CONFIG_ARCH_OMAP is not set # CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_REALVIEW is not set # CONFIG_ARCH_IMX is not set # CONFIG_ARCH_H720X is not set # CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_AT91RM9200 is not set # # SA11x0 Implementations @@ -128,20 +145,32 @@ CONFIG_SHARP_SCOOP=y # Bus support # CONFIG_ISA=y -CONFIG_ISA_DMA_API=y # # PCCARD (PCMCIA/CardBus) support # -# CONFIG_PCCARD is not set +CONFIG_PCCARD=y +CONFIG_PCMCIA_DEBUG=y +CONFIG_PCMCIA=y +CONFIG_PCMCIA_LOAD_CIS=y +CONFIG_PCMCIA_IOCTL=y + +# +# PC-card bridges +# +# CONFIG_I82365 is not set +# CONFIG_TCIC is not set +CONFIG_PCMCIA_SA1100=y # # Kernel Features # -# CONFIG_SMP is not set -CONFIG_PREEMPT=y +# CONFIG_PREEMPT is not set # CONFIG_NO_IDLE_HZ is not set +CONFIG_HZ=100 +# CONFIG_AEABI is not set CONFIG_ARCH_DISCONTIGMEM_ENABLE=y +CONFIG_NODES_SHIFT=2 CONFIG_SELECT_MEMORY_MODEL=y # CONFIG_FLATMEM_MANUAL is not set CONFIG_DISCONTIGMEM_MANUAL=y @@ -150,6 +179,7 @@ CONFIG_DISCONTIGMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y # CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 # CONFIG_LEDS is not set CONFIG_ALIGNMENT_TRAP=y @@ -158,7 +188,7 @@ CONFIG_ALIGNMENT_TRAP=y # CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 -CONFIG_CMDLINE="console=ttyS0,115200n8 console=tty1 noinitrd root=/dev/mtdblock2 rootfstype=jffs2 debug" +CONFIG_CMDLINE="noinitrd root=/dev/mtdblock2 rootfstype=jffs2 fbcon=rotate:1" # CONFIG_XIP_KERNEL is not set # @@ -181,14 +211,16 @@ CONFIG_FPE_NWFPE=y # Userspace binary formats # CONFIG_BINFMT_ELF=y -CONFIG_BINFMT_AOUT=m -CONFIG_BINFMT_MISC=m +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set # CONFIG_ARTHUR is not set # # Power management options # CONFIG_PM=y +CONFIG_PM_LEGACY=y +# CONFIG_PM_DEBUG is not set CONFIG_APM=y # @@ -199,6 +231,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -211,16 +244,19 @@ CONFIG_IP_FIB_HASH=y # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set # CONFIG_ARPD is not set -CONFIG_SYN_COOKIES=y +# CONFIG_SYN_COOKIES is not set # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -232,6 +268,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -244,8 +285,11 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# # CONFIG_NET_SCHED is not set -# CONFIG_NET_CLS_ROUTE is not set # # Network testing @@ -265,10 +309,15 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y -CONFIG_FW_LOADER=m +CONFIG_FW_LOADER=y # CONFIG_DEBUG_DRIVER is not set # +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# # Memory Technology Devices (MTD) # CONFIG_MTD=y @@ -287,32 +336,49 @@ CONFIG_MTD_BLOCK=y # CONFIG_FTL is not set # CONFIG_NFTL is not set # CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set # # RAM/ROM/Flash chip drivers # -# CONFIG_MTD_CFI is not set -# CONFIG_MTD_JEDECPROBE is not set -CONFIG_MTD_MAP_BANK_WIDTH_1=y -CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_GEN_PROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_NOSWAP=y +# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set +# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set +CONFIG_MTD_CFI_GEOMETRY=y +# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_2 is not set CONFIG_MTD_MAP_BANK_WIDTH_4=y # CONFIG_MTD_MAP_BANK_WIDTH_8 is not set # CONFIG_MTD_MAP_BANK_WIDTH_16 is not set # CONFIG_MTD_MAP_BANK_WIDTH_32 is not set -CONFIG_MTD_CFI_I1=y -CONFIG_MTD_CFI_I2=y -# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I1 is not set +# CONFIG_MTD_CFI_I2 is not set +CONFIG_MTD_CFI_I4=y # CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_OTP is not set +CONFIG_MTD_CFI_INTELEXT=y +# CONFIG_MTD_CFI_AMDSTD is not set +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set # CONFIG_MTD_ROM is not set # CONFIG_MTD_ABSENT is not set CONFIG_MTD_OBSOLETE_CHIPS=y CONFIG_MTD_SHARP=y +# CONFIG_MTD_XIP is not set # # Mapping drivers for chip access # # CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PHYSMAP is not set +# CONFIG_MTD_ARM_INTEGRATOR is not set +CONFIG_MTD_SA1100=y +# CONFIG_MTD_IMPA7 is not set # CONFIG_MTD_PLATRAM is not set # @@ -321,7 +387,6 @@ CONFIG_MTD_SHARP=y # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLKMTD is not set # CONFIG_MTD_BLOCK2MTD is not set # @@ -337,6 +402,11 @@ CONFIG_MTD_SHARP=y # CONFIG_MTD_NAND is not set # +# OneNAND Flash Device Drivers +# +# CONFIG_MTD_ONENAND is not set + +# # Parallel port support # # CONFIG_PARPORT is not set @@ -349,7 +419,6 @@ CONFIG_MTD_SHARP=y # # Block devices # -# CONFIG_BLK_DEV_XD is not set # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set @@ -359,20 +428,35 @@ CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=1024 CONFIG_BLK_DEV_INITRD=y # CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set # -# IO Schedulers +# ATA/ATAPI/MFM/RLL support # -CONFIG_IOSCHED_NOOP=y -CONFIG_IOSCHED_AS=y -CONFIG_IOSCHED_DEADLINE=y -CONFIG_IOSCHED_CFQ=y -CONFIG_ATA_OVER_ETH=m +CONFIG_IDE=y +CONFIG_BLK_DEV_IDE=y # -# ATA/ATAPI/MFM/RLL support +# Please see Documentation/ide.txt for help/info on IDE drives +# +# CONFIG_BLK_DEV_IDE_SATA is not set +CONFIG_BLK_DEV_IDEDISK=y +CONFIG_IDEDISK_MULTI_MODE=y +CONFIG_BLK_DEV_IDECS=y +# CONFIG_BLK_DEV_IDECD is not set +# CONFIG_BLK_DEV_IDETAPE is not set +# CONFIG_BLK_DEV_IDEFLOPPY is not set +# CONFIG_IDE_TASK_IOCTL is not set + +# +# IDE chipset support/bugfixes # -# CONFIG_IDE is not set +CONFIG_IDE_GENERIC=y +# CONFIG_IDE_ARM is not set +# CONFIG_IDE_CHIPSETS is not set +# CONFIG_BLK_DEV_IDEDMA is not set +# CONFIG_IDEDMA_AUTO is not set +# CONFIG_BLK_DEV_HD is not set # # SCSI device support @@ -402,6 +486,39 @@ CONFIG_ATA_OVER_ETH=m # Network device support # # CONFIG_NETDEVICES is not set +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# PHY device support +# + +# +# Ethernet (10 or 100Mbit) +# +# CONFIG_NET_ETHERNET is not set + +# +# Ethernet (1000 Mbit) +# + +# +# Ethernet (10000 Mbit) +# +CONFIG_PPP=y +# CONFIG_PPP_MULTILINK is not set +# CONFIG_PPP_FILTER is not set +CONFIG_PPP_ASYNC=y +# CONFIG_PPP_SYNC_TTY is not set +# CONFIG_PPP_DEFLATE is not set +# CONFIG_PPP_BSDCOMP is not set +# CONFIG_PPP_MPPE is not set +# CONFIG_PPPOE is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set @@ -424,7 +541,7 @@ CONFIG_INPUT_TSDEV=y CONFIG_INPUT_TSDEV_SCREEN_X=240 CONFIG_INPUT_TSDEV_SCREEN_Y=320 CONFIG_INPUT_EVDEV=y -CONFIG_INPUT_EVBUG=y +# CONFIG_INPUT_EVBUG is not set # # Input Device Drivers @@ -438,7 +555,11 @@ CONFIG_KEYBOARD_LOCOMO=y # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_INPUT_MOUSE is not set # CONFIG_INPUT_JOYSTICK is not set -# CONFIG_INPUT_TOUCHSCREEN is not set +CONFIG_INPUT_TOUCHSCREEN=y +# CONFIG_TOUCHSCREEN_GUNZE is not set +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_MK712 is not set # CONFIG_INPUT_MISC is not set # @@ -461,7 +582,16 @@ CONFIG_HW_CONSOLE=y # # Serial drivers # -# CONFIG_SERIAL_8250 is not set +CONFIG_SERIAL_8250=y +# CONFIG_SERIAL_8250_CONSOLE is not set +CONFIG_SERIAL_8250_CS=y +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SERIAL_8250_EXTENDED=y +# CONFIG_SERIAL_8250_MANY_PORTS is not set +# CONFIG_SERIAL_8250_SHARE_IRQ is not set +# CONFIG_SERIAL_8250_DETECT_IRQ is not set +# CONFIG_SERIAL_8250_RSA is not set # # Non-8250 serial port support @@ -483,94 +613,48 @@ CONFIG_UNIX98_PTYS=y # # CONFIG_WATCHDOG is not set # CONFIG_NVRAM is not set -# CONFIG_RTC is not set # CONFIG_DTLK is not set # CONFIG_R3964 is not set # # Ftape, the floppy tape device driver # -# CONFIG_RAW_DRIVER is not set # -# TPM devices +# PCMCIA character devices # +# CONFIG_SYNCLINK_CS is not set +# CONFIG_CARDMAN_4000 is not set +# CONFIG_CARDMAN_4040 is not set +# CONFIG_RAW_DRIVER is not set # -# I2C support +# TPM devices # -CONFIG_I2C=m -# CONFIG_I2C_CHARDEV is not set +# CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set # -# I2C Algorithms +# I2C support # -CONFIG_I2C_ALGOBIT=m -# CONFIG_I2C_ALGOPCF is not set -# CONFIG_I2C_ALGOPCA is not set +# CONFIG_I2C is not set # -# I2C Hardware Bus support +# SPI support # -# CONFIG_I2C_ELEKTOR is not set -# CONFIG_I2C_PARPORT_LIGHT is not set -# CONFIG_I2C_STUB is not set -# CONFIG_I2C_PCA_ISA is not set +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set # -# Miscellaneous I2C Chip support +# Dallas's 1-wire bus # -# CONFIG_SENSORS_DS1337 is not set -# CONFIG_SENSORS_DS1374 is not set -# CONFIG_SENSORS_EEPROM is not set -# CONFIG_SENSORS_PCF8574 is not set -# CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_PCF8591 is not set -# CONFIG_SENSORS_RTC8564 is not set -# CONFIG_SENSORS_MAX6875 is not set -# CONFIG_I2C_DEBUG_CORE is not set -# CONFIG_I2C_DEBUG_ALGO is not set -# CONFIG_I2C_DEBUG_BUS is not set -# CONFIG_I2C_DEBUG_CHIP is not set +# CONFIG_W1 is not set # # Hardware Monitoring support # -CONFIG_HWMON=y +# CONFIG_HWMON is not set # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ADM1021 is not set -# CONFIG_SENSORS_ADM1025 is not set -# CONFIG_SENSORS_ADM1026 is not set -# CONFIG_SENSORS_ADM1031 is not set -# CONFIG_SENSORS_ADM9240 is not set -# CONFIG_SENSORS_ASB100 is not set -# CONFIG_SENSORS_ATXP1 is not set -# CONFIG_SENSORS_DS1621 is not set -# CONFIG_SENSORS_FSCHER is not set -# CONFIG_SENSORS_FSCPOS is not set -# CONFIG_SENSORS_GL518SM is not set -# CONFIG_SENSORS_GL520SM is not set -# CONFIG_SENSORS_IT87 is not set -# CONFIG_SENSORS_LM63 is not set -# CONFIG_SENSORS_LM75 is not set -# CONFIG_SENSORS_LM77 is not set -# CONFIG_SENSORS_LM78 is not set -# CONFIG_SENSORS_LM80 is not set -# CONFIG_SENSORS_LM83 is not set -# CONFIG_SENSORS_LM85 is not set -# CONFIG_SENSORS_LM87 is not set -# CONFIG_SENSORS_LM90 is not set -# CONFIG_SENSORS_LM92 is not set -# CONFIG_SENSORS_MAX1619 is not set -# CONFIG_SENSORS_PC87360 is not set -# CONFIG_SENSORS_SMSC47M1 is not set -# CONFIG_SENSORS_SMSC47B397 is not set -# CONFIG_SENSORS_W83781D is not set -# CONFIG_SENSORS_W83792D is not set -# CONFIG_SENSORS_W83L785TS is not set -# CONFIG_SENSORS_W83627HF is not set -# CONFIG_SENSORS_W83627EHF is not set -# CONFIG_HWMON_DEBUG_CHIP is not set # # Misc devices @@ -579,42 +663,33 @@ CONFIG_HWMON=y # # Multimedia Capabilities Port drivers # -# CONFIG_MCP_SA11X0 is not set +CONFIG_MCP=y +CONFIG_MCP_SA11X0=y +CONFIG_MCP_UCB1200=y +CONFIG_MCP_UCB1200_TS=y # -# Multimedia devices +# LED devices # -CONFIG_VIDEO_DEV=m +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=y # -# Video For Linux +# LED drivers # +CONFIG_LEDS_LOCOMO=y # -# Video Adapters +# LED Triggers # -# CONFIG_VIDEO_PMS is not set -# CONFIG_VIDEO_CPIA is not set -# CONFIG_VIDEO_SAA5246A is not set -# CONFIG_VIDEO_SAA5249 is not set -# CONFIG_TUNER_3036 is not set -# CONFIG_VIDEO_OVCAMCHIP is not set +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_TIMER=y +CONFIG_LEDS_TRIGGER_IDE_DISK=y # -# Radio Adapters +# Multimedia devices # -# CONFIG_RADIO_CADET is not set -# CONFIG_RADIO_RTRACK is not set -# CONFIG_RADIO_RTRACK2 is not set -# CONFIG_RADIO_AZTECH is not set -# CONFIG_RADIO_GEMTEK is not set -# CONFIG_RADIO_MAESTRO is not set -# CONFIG_RADIO_SF16FMI is not set -# CONFIG_RADIO_SF16FMR2 is not set -# CONFIG_RADIO_TERRATEC is not set -# CONFIG_RADIO_TRUST is not set -# CONFIG_RADIO_TYPHOON is not set -# CONFIG_RADIO_ZOLTRIX is not set +# CONFIG_VIDEO_DEV is not set # # Digital Video Broadcasting Devices @@ -628,8 +703,8 @@ CONFIG_FB=y CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y -CONFIG_FB_SOFT_CURSOR=y # CONFIG_FB_MACMODES is not set +# CONFIG_FB_FIRMWARE_EDID is not set CONFIG_FB_MODE_HELPERS=y # CONFIG_FB_TILEBLITTING is not set CONFIG_FB_SA1100=y @@ -643,14 +718,15 @@ CONFIG_FB_SA1100=y # CONFIG_MDA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y +CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y CONFIG_FONTS=y -CONFIG_FONT_8x8=y +# CONFIG_FONT_8x8 is not set # CONFIG_FONT_8x16 is not set # CONFIG_FONT_6x11 is not set # CONFIG_FONT_7x14 is not set # CONFIG_FONT_PEARL_8x8 is not set # CONFIG_FONT_ACORN_8x8 is not set -# CONFIG_FONT_MINI_4x6 is not set +CONFIG_FONT_MINI_4x6=y # CONFIG_FONT_SUN8x16 is not set # CONFIG_FONT_SUN12x22 is not set # CONFIG_FONT_10x18 is not set @@ -659,7 +735,11 @@ CONFIG_FONT_8x8=y # Logo configuration # # CONFIG_LOGO is not set -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_BACKLIGHT_CLASS_DEVICE=y +CONFIG_BACKLIGHT_DEVICE=y +CONFIG_LCD_CLASS_DEVICE=y +CONFIG_LCD_DEVICE=y # # Sound @@ -671,20 +751,17 @@ CONFIG_FONT_8x8=y # CONFIG_USB_ARCH_HAS_HCD=y # CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set # CONFIG_USB is not set # +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# # USB Gadget Support # -CONFIG_USB_GADGET=y -# CONFIG_USB_GADGET_DEBUG_FILES is not set -# CONFIG_USB_GADGET_NET2280 is not set -# CONFIG_USB_GADGET_PXA2XX is not set -# CONFIG_USB_GADGET_GOKU is not set -# CONFIG_USB_GADGET_LH7A40X is not set -# CONFIG_USB_GADGET_OMAP is not set -# CONFIG_USB_GADGET_DUMMY_HCD is not set -# CONFIG_USB_GADGET_DUALSPEED is not set +# CONFIG_USB_GADGET is not set # # MMC/SD Card support @@ -692,23 +769,24 @@ CONFIG_USB_GADGET=y # CONFIG_MMC is not set # +# Real Time Clock +# +CONFIG_RTC_LIB=y +# CONFIG_RTC_CLASS is not set + +# # File systems # -CONFIG_EXT2_FS=y -CONFIG_EXT2_FS_XATTR=y -CONFIG_EXT2_FS_POSIX_ACL=y -CONFIG_EXT2_FS_SECURITY=y -# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT2_FS is not set # CONFIG_EXT3_FS is not set -# CONFIG_JBD is not set -CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set -CONFIG_FS_POSIX_ACL=y +# CONFIG_FS_POSIX_ACL is not set # CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set # CONFIG_MINIX_FS is not set CONFIG_ROMFS_FS=y -CONFIG_INOTIFY=y +# CONFIG_INOTIFY is not set # CONFIG_QUOTA is not set # CONFIG_DNOTIFY is not set # CONFIG_AUTOFS_FS is not set @@ -725,7 +803,7 @@ CONFIG_INOTIFY=y # DOS/FAT/NT Filesystems # CONFIG_FAT_FS=y -CONFIG_MSDOS_FS=y +# CONFIG_MSDOS_FS is not set CONFIG_VFAT_FS=y CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" @@ -739,7 +817,7 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -# CONFIG_RELAYFS_FS is not set +# CONFIG_CONFIGFS_FS is not set # # Miscellaneous filesystems @@ -755,11 +833,12 @@ CONFIG_RAMFS=y CONFIG_JFFS2_FS=y CONFIG_JFFS2_FS_DEBUG=0 CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_SUMMARY is not set # CONFIG_JFFS2_COMPRESSION_OPTIONS is not set CONFIG_JFFS2_ZLIB=y CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set -CONFIG_CRAMFS=y +# CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set @@ -789,7 +868,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_NLS=y CONFIG_NLS_DEFAULT="cp437" -CONFIG_NLS_CODEPAGE_437=m +CONFIG_NLS_CODEPAGE_437=y # CONFIG_NLS_CODEPAGE_737 is not set # CONFIG_NLS_CODEPAGE_775 is not set # CONFIG_NLS_CODEPAGE_850 is not set @@ -813,7 +892,7 @@ CONFIG_NLS_CODEPAGE_437=m # CONFIG_NLS_CODEPAGE_1250 is not set # CONFIG_NLS_CODEPAGE_1251 is not set # CONFIG_NLS_ASCII is not set -CONFIG_NLS_ISO8859_1=m +CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_ISO8859_2 is not set # CONFIG_NLS_ISO8859_3 is not set # CONFIG_NLS_ISO8859_4 is not set @@ -826,7 +905,7 @@ CONFIG_NLS_ISO8859_1=m # CONFIG_NLS_ISO8859_15 is not set # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set -CONFIG_NLS_UTF8=m +# CONFIG_NLS_UTF8 is not set # # Profiling support @@ -837,20 +916,23 @@ CONFIG_NLS_UTF8=m # Kernel hacking # # CONFIG_PRINTK_TIME is not set -CONFIG_DEBUG_KERNEL=y CONFIG_MAGIC_SYSRQ=y +CONFIG_DEBUG_KERNEL=y CONFIG_LOG_BUF_SHIFT=14 -CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_DETECT_SOFTLOCKUP is not set # CONFIG_SCHEDSTATS is not set -# CONFIG_DEBUG_SLAB is not set -CONFIG_DEBUG_PREEMPT=y +CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_KOBJECT is not set # CONFIG_DEBUG_BUGVERBOSE is not set # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set CONFIG_FRAME_POINTER=y +# CONFIG_UNWIND_INFO is not set +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set # CONFIG_DEBUG_USER is not set # CONFIG_DEBUG_WAITQ is not set CONFIG_DEBUG_ERRORS=y @@ -874,7 +956,7 @@ CONFIG_DEBUG_ERRORS=y # # Library routines # -# CONFIG_CRC_CCITT is not set +CONFIG_CRC_CCITT=y # CONFIG_CRC16 is not set CONFIG_CRC32=y # CONFIG_LIBCRC32C is not set diff --git a/arch/arm/configs/versatile_defconfig b/arch/arm/configs/versatile_defconfig index 2687a225aa6..96b7a776242 100644 --- a/arch/arm/configs/versatile_defconfig +++ b/arch/arm/configs/versatile_defconfig @@ -1,50 +1,55 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.12-rc1-bk2 -# Mon Mar 28 00:20:50 2005 +# Linux kernel version: 2.6.17-rc3 +# Mon May 8 20:15:57 2006 # CONFIG_ARM=y CONFIG_MMU=y -CONFIG_UID16=y CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y -CONFIG_GENERIC_IOMAP=y +CONFIG_VECTORS_BASE=0xffff0000 # # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 # # General setup # CONFIG_LOCALVERSION="" +# CONFIG_LOCALVERSION_AUTO is not set CONFIG_SWAP=y CONFIG_SYSVIPC=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set CONFIG_SYSCTL=y # CONFIG_AUDIT is not set -CONFIG_HOTPLUG=y -CONFIG_KOBJECT_UEVENT=y # CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_UID16=y +CONFIG_CC_OPTIMIZE_FOR_SIZE=y # CONFIG_EMBEDDED is not set CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y -CONFIG_CC_OPTIMIZE_FOR_SIZE=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 +CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set +CONFIG_OBSOLETE_INTERMODULE=y # # Loadable module support @@ -52,23 +57,42 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_KMOD=y # +# Block layer +# +# CONFIG_BLK_DEV_IO_TRACE is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# # System Type # # CONFIG_ARCH_CLPS7500 is not set # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP23XX is not set # CONFIG_ARCH_L7200 is not set # CONFIG_ARCH_PXA is not set # CONFIG_ARCH_RPC is not set @@ -78,14 +102,17 @@ CONFIG_KMOD=y # CONFIG_ARCH_LH7A40X is not set # CONFIG_ARCH_OMAP is not set CONFIG_ARCH_VERSATILE=y +# CONFIG_ARCH_REALVIEW is not set # CONFIG_ARCH_IMX is not set # CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_AT91RM9200 is not set # # Versatile platform type # CONFIG_ARCH_VERSATILE_PB=y -# CONFIG_MACH_VERSATILE_AB is not set +CONFIG_MACH_VERSATILE_AB=y # # Processor Type @@ -106,12 +133,14 @@ CONFIG_ARM_THUMB=y # CONFIG_CPU_DCACHE_DISABLE is not set # CONFIG_CPU_DCACHE_WRITETHROUGH is not set # CONFIG_CPU_CACHE_ROUND_ROBIN is not set +CONFIG_ARM_VIC=y CONFIG_ICST307=y # # Bus support # CONFIG_ARM_AMBA=y +# CONFIG_PCI is not set # # PCCARD (PCMCIA/CardBus) support @@ -122,6 +151,18 @@ CONFIG_ARM_AMBA=y # Kernel Features # # CONFIG_PREEMPT is not set +# CONFIG_NO_IDLE_HZ is not set +CONFIG_HZ=100 +# CONFIG_AEABI is not set +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 CONFIG_LEDS=y CONFIG_LEDS_TIMER=y CONFIG_LEDS_CPU=y @@ -145,7 +186,7 @@ CONFIG_CMDLINE="root=1f03 mem=32M" CONFIG_FPE_NWFPE=y # CONFIG_FPE_NWFPE_XP is not set # CONFIG_FPE_FASTFPE is not set -# CONFIG_VFP is not set +CONFIG_VFP=y # # Userspace binary formats @@ -159,9 +200,92 @@ CONFIG_BINFMT_ELF=y # Power management options # CONFIG_PM=y +CONFIG_PM_LEGACY=y +# CONFIG_PM_DEBUG is not set # CONFIG_APM is not set # +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +# CONFIG_NETDEBUG is not set +CONFIG_PACKET=y +CONFIG_PACKET_MMAP=y +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +# CONFIG_INET_DIAG is not set +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_BIC=y +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_NET_DIVERT is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# # Device Drivers # @@ -174,6 +298,11 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_DEBUG_DRIVER is not set # +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# # Memory Technology Devices (MTD) # CONFIG_MTD=y @@ -192,6 +321,7 @@ CONFIG_MTD_BLOCK=y # CONFIG_FTL is not set # CONFIG_NFTL is not set # CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set # # RAM/ROM/Flash chip drivers @@ -214,6 +344,7 @@ CONFIG_MTD_CFI_I1=y CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I4 is not set # CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_OTP is not set CONFIG_MTD_CFI_INTELEXT=y # CONFIG_MTD_CFI_AMDSTD is not set # CONFIG_MTD_CFI_STAA is not set @@ -221,7 +352,7 @@ CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set # CONFIG_MTD_ROM is not set # CONFIG_MTD_ABSENT is not set -# CONFIG_MTD_XIP is not set +# CONFIG_MTD_OBSOLETE_CHIPS is not set # # Mapping drivers for chip access @@ -229,7 +360,7 @@ CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_COMPLEX_MAPPINGS is not set # CONFIG_MTD_PHYSMAP is not set CONFIG_MTD_ARM_INTEGRATOR=y -# CONFIG_MTD_EDB7312 is not set +# CONFIG_MTD_PLATRAM is not set # # Self-contained MTD device drivers @@ -237,7 +368,6 @@ CONFIG_MTD_ARM_INTEGRATOR=y # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLKMTD is not set # CONFIG_MTD_BLOCK2MTD is not set # @@ -253,6 +383,11 @@ CONFIG_MTD_ARM_INTEGRATOR=y # CONFIG_MTD_NAND is not set # +# OneNAND Flash Device Drivers +# +# CONFIG_MTD_ONENAND is not set + +# # Parallel port support # # CONFIG_PARPORT is not set @@ -264,7 +399,6 @@ CONFIG_MTD_ARM_INTEGRATOR=y # # Block devices # -# CONFIG_BLK_DEV_FD is not set # CONFIG_BLK_DEV_COW_COMMON is not set # CONFIG_BLK_DEV_LOOP is not set # CONFIG_BLK_DEV_NBD is not set @@ -272,21 +406,13 @@ CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=4096 CONFIG_BLK_DEV_INITRD=y -CONFIG_INITRAMFS_SOURCE="" # CONFIG_CDROM_PKTCDVD is not set - -# -# IO Schedulers -# -CONFIG_IOSCHED_NOOP=y -CONFIG_IOSCHED_AS=y -CONFIG_IOSCHED_DEADLINE=y -CONFIG_IOSCHED_CFQ=y # CONFIG_ATA_OVER_ETH is not set # # SCSI device support # +# CONFIG_RAID_ATTRS is not set # CONFIG_SCSI is not set # @@ -297,6 +423,7 @@ CONFIG_IOSCHED_CFQ=y # # Fusion MPT device support # +# CONFIG_FUSION is not set # # IEEE 1394 (FireWire) support @@ -307,71 +434,8 @@ CONFIG_IOSCHED_CFQ=y # # -# Networking support -# -CONFIG_NET=y - -# -# Networking options -# -CONFIG_PACKET=y -CONFIG_PACKET_MMAP=y -# CONFIG_NETLINK_DEV is not set -CONFIG_UNIX=y -# CONFIG_NET_KEY is not set -CONFIG_INET=y -CONFIG_IP_MULTICAST=y -# CONFIG_IP_ADVANCED_ROUTER is not set -CONFIG_IP_PNP=y -# CONFIG_IP_PNP_DHCP is not set -CONFIG_IP_PNP_BOOTP=y -# CONFIG_IP_PNP_RARP is not set -# CONFIG_NET_IPIP is not set -# CONFIG_NET_IPGRE is not set -# CONFIG_IP_MROUTE is not set -# CONFIG_ARPD is not set -# CONFIG_SYN_COOKIES is not set -# CONFIG_INET_AH is not set -# CONFIG_INET_ESP is not set -# CONFIG_INET_IPCOMP is not set -# CONFIG_INET_TUNNEL is not set -# CONFIG_IP_TCPDIAG is not set -# CONFIG_IP_TCPDIAG_IPV6 is not set -# CONFIG_IPV6 is not set -# CONFIG_NETFILTER is not set - -# -# SCTP Configuration (EXPERIMENTAL) -# -# CONFIG_IP_SCTP is not set -# CONFIG_ATM is not set -# CONFIG_BRIDGE is not set -# CONFIG_VLAN_8021Q is not set -# CONFIG_DECNET is not set -# CONFIG_LLC2 is not set -# CONFIG_IPX is not set -# CONFIG_ATALK is not set -# CONFIG_X25 is not set -# CONFIG_LAPB is not set -# CONFIG_NET_DIVERT is not set -# CONFIG_ECONET is not set -# CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# -# CONFIG_NET_SCHED is not set -# CONFIG_NET_CLS_ROUTE is not set - -# -# Network testing +# Network device support # -# CONFIG_NET_PKTGEN is not set -# CONFIG_NETPOLL is not set -# CONFIG_NET_POLL_CONTROLLER is not set -# CONFIG_HAMRADIO is not set -# CONFIG_IRDA is not set -# CONFIG_BT is not set CONFIG_NETDEVICES=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set @@ -379,11 +443,17 @@ CONFIG_NETDEVICES=y # CONFIG_TUN is not set # +# PHY device support +# +# CONFIG_PHYLIB is not set + +# # Ethernet (10 or 100Mbit) # CONFIG_NET_ETHERNET=y CONFIG_MII=y CONFIG_SMC91X=y +# CONFIG_DM9000 is not set # # Ethernet (1000 Mbit) @@ -410,6 +480,8 @@ CONFIG_SMC91X=y # CONFIG_SLIP is not set # CONFIG_SHAPER is not set # CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set # # ISDN subsystem @@ -459,7 +531,6 @@ CONFIG_SERIO_AMBAKMI=y CONFIG_SERIO_LIBPS2=y # CONFIG_SERIO_RAW is not set # CONFIG_GAMEPORT is not set -CONFIG_SOUND_GAMEPORT=y # # Character devices @@ -474,17 +545,16 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=m CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_MANY_PORTS=y CONFIG_SERIAL_8250_SHARE_IRQ=y # CONFIG_SERIAL_8250_DETECT_IRQ is not set -CONFIG_SERIAL_8250_MULTIPORT=y CONFIG_SERIAL_8250_RSA=y # # Non-8250 serial port support # -# CONFIG_SERIAL_AMBA_PL010 is not set CONFIG_SERIAL_AMBA_PL011=y CONFIG_SERIAL_AMBA_PL011_CONSOLE=y CONFIG_SERIAL_CORE=y @@ -503,20 +573,19 @@ CONFIG_LEGACY_PTY_COUNT=16 # # CONFIG_WATCHDOG is not set # CONFIG_NVRAM is not set -# CONFIG_RTC is not set # CONFIG_DTLK is not set # CONFIG_R3964 is not set # # Ftape, the floppy tape device driver # -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # # TPM devices # # CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set # # I2C support @@ -534,60 +603,60 @@ CONFIG_I2C_ALGOBIT=y # # I2C Hardware Bus support # -# CONFIG_I2C_ISA is not set # CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_STUB is not set # CONFIG_I2C_PCA_ISA is not set # -# Hardware Sensors Chip support -# -CONFIG_I2C_SENSOR=m -# CONFIG_SENSORS_ADM1021 is not set -# CONFIG_SENSORS_ADM1025 is not set -# CONFIG_SENSORS_ADM1026 is not set -# CONFIG_SENSORS_ADM1031 is not set -# CONFIG_SENSORS_ASB100 is not set -# CONFIG_SENSORS_DS1621 is not set -# CONFIG_SENSORS_FSCHER is not set -# CONFIG_SENSORS_FSCPOS is not set -# CONFIG_SENSORS_GL518SM is not set -# CONFIG_SENSORS_GL520SM is not set -# CONFIG_SENSORS_IT87 is not set -# CONFIG_SENSORS_LM63 is not set -# CONFIG_SENSORS_LM75 is not set -# CONFIG_SENSORS_LM77 is not set -# CONFIG_SENSORS_LM78 is not set -# CONFIG_SENSORS_LM80 is not set -# CONFIG_SENSORS_LM83 is not set -# CONFIG_SENSORS_LM85 is not set -# CONFIG_SENSORS_LM87 is not set -# CONFIG_SENSORS_LM90 is not set -# CONFIG_SENSORS_MAX1619 is not set -# CONFIG_SENSORS_PC87360 is not set -# CONFIG_SENSORS_SMSC47B397 is not set -# CONFIG_SENSORS_SMSC47M1 is not set -# CONFIG_SENSORS_W83781D is not set -# CONFIG_SENSORS_W83L785TS is not set -# CONFIG_SENSORS_W83627HF is not set - -# -# Other I2C Chip support +# Miscellaneous I2C Chip support # +# CONFIG_SENSORS_DS1337 is not set +# CONFIG_SENSORS_DS1374 is not set CONFIG_SENSORS_EEPROM=m # CONFIG_SENSORS_PCF8574 is not set +# CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set -# CONFIG_SENSORS_RTC8564 is not set +# CONFIG_SENSORS_MAX6875 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # +# SPI support +# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Hardware Monitoring support +# +# CONFIG_HWMON is not set +# CONFIG_HWMON_VID is not set + +# # Misc devices # # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -604,27 +673,31 @@ CONFIG_FB=y CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y -CONFIG_FB_SOFT_CURSOR=y +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_FIRMWARE_EDID is not set # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set CONFIG_FB_ARMCLCD=y +# CONFIG_FB_S1D13XXX is not set # CONFIG_FB_VIRTUAL is not set # # Console display driver support # -# CONFIG_VGA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set CONFIG_FONTS=y # CONFIG_FONT_8x8 is not set # CONFIG_FONT_8x16 is not set # CONFIG_FONT_6x11 is not set +# CONFIG_FONT_7x14 is not set # CONFIG_FONT_PEARL_8x8 is not set CONFIG_FONT_ACORN_8x8=y # CONFIG_FONT_MINI_4x6 is not set # CONFIG_FONT_SUN8x16 is not set # CONFIG_FONT_SUN12x22 is not set +# CONFIG_FONT_10x18 is not set # # Logo configuration @@ -647,12 +720,18 @@ CONFIG_SND_PCM=m CONFIG_SND_OSSEMUL=y CONFIG_SND_MIXER_OSS=m CONFIG_SND_PCM_OSS=m +CONFIG_SND_PCM_OSS_PLUGINS=y +# CONFIG_SND_DYNAMIC_MINORS is not set +CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set # # Generic devices # +CONFIG_SND_AC97_CODEC=m +CONFIG_SND_AC97_BUS=m # CONFIG_SND_DUMMY is not set # CONFIG_SND_MTPAV is not set # CONFIG_SND_SERIAL_U16550 is not set @@ -661,6 +740,7 @@ CONFIG_SND_PCM_OSS=m # # ALSA ARM devices # +CONFIG_SND_ARMAACI=m # # Open Sound System @@ -672,9 +752,14 @@ CONFIG_SND_PCM_OSS=m # CONFIG_USB_ARCH_HAS_HCD=y # CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set # CONFIG_USB is not set # +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# # USB Gadget Support # # CONFIG_USB_GADGET is not set @@ -688,25 +773,31 @@ CONFIG_MMC_BLOCK=y CONFIG_MMC_ARMMMCI=m # +# Real Time Clock +# +CONFIG_RTC_LIB=y +# CONFIG_RTC_CLASS is not set + +# # File systems # CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set # CONFIG_EXT3_FS is not set -# CONFIG_JBD is not set # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set - -# -# XFS support -# +# CONFIG_FS_POSIX_ACL is not set # CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set CONFIG_MINIX_FS=y CONFIG_ROMFS_FS=y +# CONFIG_INOTIFY is not set # CONFIG_QUOTA is not set CONFIG_DNOTIFY=y # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set # # CD-ROM/DVD Filesystems @@ -729,11 +820,10 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" # CONFIG_PROC_FS=y CONFIG_SYSFS=y -# CONFIG_DEVFS_FS is not set -# CONFIG_DEVPTS_FS_XATTR is not set # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y +# CONFIG_CONFIGFS_FS is not set # # Miscellaneous filesystems @@ -748,8 +838,8 @@ CONFIG_RAMFS=y # CONFIG_JFFS_FS is not set CONFIG_JFFS2_FS=y CONFIG_JFFS2_FS_DEBUG=0 -# CONFIG_JFFS2_FS_NAND is not set -# CONFIG_JFFS2_FS_NOR_ECC is not set +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_SUMMARY is not set # CONFIG_JFFS2_COMPRESSION_OPTIONS is not set CONFIG_JFFS2_ZLIB=y CONFIG_JFFS2_RTIME=y @@ -766,16 +856,19 @@ CONFIG_CRAMFS=y # CONFIG_NFS_FS=y CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set # CONFIG_NFS_V4 is not set # CONFIG_NFS_DIRECTIO is not set CONFIG_NFSD=y CONFIG_NFSD_V3=y +# CONFIG_NFSD_V3_ACL is not set # CONFIG_NFSD_V4 is not set # CONFIG_NFSD_TCP is not set CONFIG_ROOT_NFS=y CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=y +CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set @@ -784,6 +877,7 @@ CONFIG_SUNRPC=y # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set # # Partition Types @@ -803,6 +897,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_SGI_PARTITION is not set # CONFIG_ULTRIX_PARTITION is not set # CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # @@ -858,18 +953,24 @@ CONFIG_NLS_ISO8859_1=m # Kernel hacking # # CONFIG_PRINTK_TIME is not set -CONFIG_DEBUG_KERNEL=y CONFIG_MAGIC_SYSRQ=y +CONFIG_DEBUG_KERNEL=y CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y # CONFIG_SCHEDSTATS is not set # CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_MUTEXES is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_KOBJECT is not set CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set CONFIG_FRAME_POINTER=y +# CONFIG_UNWIND_INFO is not set +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set CONFIG_DEBUG_USER=y # CONFIG_DEBUG_WAITQ is not set CONFIG_DEBUG_ERRORS=y @@ -895,6 +996,7 @@ CONFIG_DEBUG_LL=y # Library routines # # CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set CONFIG_CRC32=y # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y diff --git a/arch/arm/kernel/asm-offsets.c b/arch/arm/kernel/asm-offsets.c index b324dcac1c5..45fdf4a51a2 100644 --- a/arch/arm/kernel/asm-offsets.c +++ b/arch/arm/kernel/asm-offsets.c @@ -95,5 +95,11 @@ int main(void) DEFINE(SYS_ERROR0, 0x9f0000); BLANK(); DEFINE(SIZEOF_MACHINE_DESC, sizeof(struct machine_desc)); + DEFINE(MACHINFO_TYPE, offsetof(struct machine_desc, nr)); + DEFINE(MACHINFO_NAME, offsetof(struct machine_desc, name)); + DEFINE(MACHINFO_PHYSIO, offsetof(struct machine_desc, phys_io)); + DEFINE(MACHINFO_PGOFFIO, offsetof(struct machine_desc, io_pg_offst)); + DEFINE(PROCINFO_INITFUNC, offsetof(struct proc_info_list, __cpu_flush)); + DEFINE(PROCINFO_MMUFLAGS, offsetof(struct proc_info_list, __cpu_mmu_flags)); return 0; } diff --git a/arch/arm/kernel/head-nommu.S b/arch/arm/kernel/head-nommu.S index 0bea6586405..adf62e5eaad 100644 --- a/arch/arm/kernel/head-nommu.S +++ b/arch/arm/kernel/head-nommu.S @@ -20,12 +20,10 @@ #include <asm/mach-types.h> #include <asm/procinfo.h> #include <asm/ptrace.h> +#include <asm/asm-offsets.h> #include <asm/thread_info.h> #include <asm/system.h> -#define PROCINFO_INITFUNC 12 -#define MACHINFO_TYPE 0 - /* * Kernel startup entry point. * --------------------------- diff --git a/arch/arm/kernel/head.S b/arch/arm/kernel/head.S index 04b66a9328e..04f7344e356 100644 --- a/arch/arm/kernel/head.S +++ b/arch/arm/kernel/head.S @@ -24,14 +24,6 @@ #include <asm/thread_info.h> #include <asm/system.h> -#define PROCINFO_MMUFLAGS 8 -#define PROCINFO_INITFUNC 12 - -#define MACHINFO_TYPE 0 -#define MACHINFO_PHYSIO 4 -#define MACHINFO_PGOFFIO 8 -#define MACHINFO_NAME 12 - #define KERNEL_RAM_ADDR (PAGE_OFFSET + TEXT_OFFSET) /* diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index 1ff75cee4b0..1a1539e3a94 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -264,8 +264,12 @@ void show_fpregs(struct user_fp *regs) /* * Task structure and kernel stack allocation. */ -static unsigned long *thread_info_head; -static unsigned int nr_thread_info; +struct thread_info_list { + unsigned long *head; + unsigned int nr; +}; + +static DEFINE_PER_CPU(struct thread_info_list, thread_info_list) = { NULL, 0 }; #define EXTRA_TASK_STRUCT 4 @@ -274,12 +278,15 @@ struct thread_info *alloc_thread_info(struct task_struct *task) struct thread_info *thread = NULL; if (EXTRA_TASK_STRUCT) { - unsigned long *p = thread_info_head; + struct thread_info_list *th = &get_cpu_var(thread_info_list); + unsigned long *p = th->head; if (p) { - thread_info_head = (unsigned long *)p[0]; - nr_thread_info -= 1; + th->head = (unsigned long *)p[0]; + th->nr -= 1; } + put_cpu_var(thread_info_list); + thread = (struct thread_info *)p; } @@ -300,13 +307,19 @@ struct thread_info *alloc_thread_info(struct task_struct *task) void free_thread_info(struct thread_info *thread) { - if (EXTRA_TASK_STRUCT && nr_thread_info < EXTRA_TASK_STRUCT) { - unsigned long *p = (unsigned long *)thread; - p[0] = (unsigned long)thread_info_head; - thread_info_head = p; - nr_thread_info += 1; - } else - free_pages((unsigned long)thread, THREAD_SIZE_ORDER); + if (EXTRA_TASK_STRUCT) { + struct thread_info_list *th = &get_cpu_var(thread_info_list); + if (th->nr < EXTRA_TASK_STRUCT) { + unsigned long *p = (unsigned long *)thread; + p[0] = th->head; + th->head = p; + th->nr += 1; + put_cpu_var(thread_info_list); + return; + } + put_cpu_var(thread_info_list); + } + free_pages((unsigned long)thread, THREAD_SIZE_ORDER); } /* diff --git a/arch/arm/mach-aaec2000/aaed2000.c b/arch/arm/mach-aaec2000/aaed2000.c index dc5fa8e5ebe..83f57da3184 100644 --- a/arch/arm/mach-aaec2000/aaed2000.c +++ b/arch/arm/mach-aaec2000/aaed2000.c @@ -79,7 +79,12 @@ static void __init aaed2000_init(void) } static struct map_desc aaed2000_io_desc[] __initdata = { - { EXT_GPIO_VBASE, EXT_GPIO_PBASE, EXT_GPIO_LENGTH, MT_DEVICE }, /* Ext GPIO */ + { + .virtual = EXT_GPIO_VBASE, + .pfn = __phys_to_pfn(EXT_GPIO_PBASE), + .length = EXT_GPIO_LENGTH, + .type = MT_DEVICE + }, }; static void __init aaed2000_map_io(void) diff --git a/arch/arm/mach-aaec2000/core.c b/arch/arm/mach-aaec2000/core.c index dce4815cf53..65be5efd633 100644 --- a/arch/arm/mach-aaec2000/core.c +++ b/arch/arm/mach-aaec2000/core.c @@ -20,7 +20,6 @@ #include <linux/interrupt.h> #include <linux/timex.h> #include <linux/signal.h> -#include <linux/amba/bus.h> #include <asm/hardware.h> #include <asm/irq.h> @@ -50,12 +49,12 @@ static struct map_desc standard_io_desc[] __initdata = { { .virtual = VIO_APB_BASE, - .physical = __phys_to_pfn(PIO_APB_BASE), + .pfn = __phys_to_pfn(PIO_APB_BASE), .length = IO_APB_LENGTH, .type = MT_DEVICE }, { .virtual = VIO_AHB_BASE, - .physical = __phys_to_pfn(PIO_AHB_BASE), + .pfn = __phys_to_pfn(PIO_AHB_BASE), .length = IO_AHB_LENGTH, .type = MT_DEVICE } diff --git a/arch/arm/mach-aaec2000/core.h b/arch/arm/mach-aaec2000/core.h index b6029a95f19..59501b57316 100644 --- a/arch/arm/mach-aaec2000/core.h +++ b/arch/arm/mach-aaec2000/core.h @@ -9,6 +9,7 @@ * */ +#include <linux/amba/bus.h> #include <linux/amba/clcd.h> struct sys_timer; diff --git a/arch/arm/mach-imx/generic.c b/arch/arm/mach-imx/generic.c index 9d8331be2b5..12ea58a3b84 100644 --- a/arch/arm/mach-imx/generic.c +++ b/arch/arm/mach-imx/generic.c @@ -195,56 +195,6 @@ void __init imx_set_mmc_info(struct imxmmc_platform_data *info) } EXPORT_SYMBOL(imx_set_mmc_info); -static struct resource imx_uart1_resources[] = { - [0] = { - .start = 0x00206000, - .end = 0x002060FF, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = (UART1_MINT_RX), - .end = (UART1_MINT_RX), - .flags = IORESOURCE_IRQ, - }, - [2] = { - .start = (UART1_MINT_TX), - .end = (UART1_MINT_TX), - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device imx_uart1_device = { - .name = "imx-uart", - .id = 0, - .num_resources = ARRAY_SIZE(imx_uart1_resources), - .resource = imx_uart1_resources, -}; - -static struct resource imx_uart2_resources[] = { - [0] = { - .start = 0x00207000, - .end = 0x002070FF, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = (UART2_MINT_RX), - .end = (UART2_MINT_RX), - .flags = IORESOURCE_IRQ, - }, - [2] = { - .start = (UART2_MINT_TX), - .end = (UART2_MINT_TX), - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device imx_uart2_device = { - .name = "imx-uart", - .id = 1, - .num_resources = ARRAY_SIZE(imx_uart2_resources), - .resource = imx_uart2_resources, -}; - static struct imxfb_mach_info imx_fb_info; void __init set_imx_fb_info(struct imxfb_mach_info *hard_imx_fb_info) @@ -283,8 +233,6 @@ static struct platform_device imxfb_device = { static struct platform_device *devices[] __initdata = { &imx_mmc_device, &imxfb_device, - &imx_uart1_device, - &imx_uart2_device, }; static struct map_desc imx_io_desc[] __initdata = { diff --git a/arch/arm/mach-imx/mx1ads.c b/arch/arm/mach-imx/mx1ads.c index e34d0df90ae..da893c80d47 100644 --- a/arch/arm/mach-imx/mx1ads.c +++ b/arch/arm/mach-imx/mx1ads.c @@ -26,6 +26,7 @@ #include <asm/mach/arch.h> #include <asm/arch/mmc.h> +#include <asm/arch/imx-uart.h> #include <linux/interrupt.h> #include "generic.h" @@ -48,8 +49,70 @@ static struct platform_device cs89x0_device = { .resource = cs89x0_resources, }; +static struct imxuart_platform_data uart_pdata = { + .flags = IMXUART_HAVE_RTSCTS, +}; + +static struct resource imx_uart1_resources[] = { + [0] = { + .start = 0x00206000, + .end = 0x002060FF, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = (UART1_MINT_RX), + .end = (UART1_MINT_RX), + .flags = IORESOURCE_IRQ, + }, + [2] = { + .start = (UART1_MINT_TX), + .end = (UART1_MINT_TX), + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device imx_uart1_device = { + .name = "imx-uart", + .id = 0, + .num_resources = ARRAY_SIZE(imx_uart1_resources), + .resource = imx_uart1_resources, + .dev = { + .platform_data = &uart_pdata, + } +}; + +static struct resource imx_uart2_resources[] = { + [0] = { + .start = 0x00207000, + .end = 0x002070FF, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = (UART2_MINT_RX), + .end = (UART2_MINT_RX), + .flags = IORESOURCE_IRQ, + }, + [2] = { + .start = (UART2_MINT_TX), + .end = (UART2_MINT_TX), + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device imx_uart2_device = { + .name = "imx-uart", + .id = 1, + .num_resources = ARRAY_SIZE(imx_uart2_resources), + .resource = imx_uart2_resources, + .dev = { + .platform_data = &uart_pdata, + } +}; + static struct platform_device *devices[] __initdata = { &cs89x0_device, + &imx_uart1_device, + &imx_uart2_device, }; #ifdef CONFIG_MMC_IMX @@ -75,6 +138,17 @@ mx1ads_init(void) imx_gpio_mode(GPIO_PORTB | GPIO_GIUS | GPIO_IN | 20); imx_set_mmc_info(&mx1ads_mmc_info); #endif + + imx_gpio_mode(PC9_PF_UART1_CTS); + imx_gpio_mode(PC10_PF_UART1_RTS); + imx_gpio_mode(PC11_PF_UART1_TXD); + imx_gpio_mode(PC12_PF_UART1_RXD); + + imx_gpio_mode(PB28_PF_UART2_CTS); + imx_gpio_mode(PB29_PF_UART2_RTS); + imx_gpio_mode(PB30_PF_UART2_TXD); + imx_gpio_mode(PB31_PF_UART2_RXD); + platform_add_devices(devices, ARRAY_SIZE(devices)); } @@ -87,7 +161,7 @@ mx1ads_map_io(void) MACHINE_START(MX1ADS, "Motorola MX1ADS") /* Maintainer: Sascha Hauer, Pengutronix */ .phys_io = 0x00200000, - .io_pg_offst = ((0xe0200000) >> 18) & 0xfffc, + .io_pg_offst = ((0xe0000000) >> 18) & 0xfffc, .boot_params = 0x08000100, .map_io = mx1ads_map_io, .init_irq = imx_init_irq, diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig index 5bf50a2a737..2a39f9e481a 100644 --- a/arch/arm/mach-ixp4xx/Kconfig +++ b/arch/arm/mach-ixp4xx/Kconfig @@ -11,6 +11,7 @@ comment "IXP4xx Platforms" config MACH_NSLU2 bool prompt "Linksys NSLU2" + select PCI help Say 'Y' here if you want your kernel to support Linksys's NSLU2 NAS device. For more information on this platform, @@ -18,6 +19,7 @@ config MACH_NSLU2 config ARCH_AVILA bool "Avila" + select PCI help Say 'Y' here if you want your kernel to support the Gateworks Avila Network Platform. For more information on this platform, @@ -25,6 +27,7 @@ config ARCH_AVILA config ARCH_ADI_COYOTE bool "Coyote" + select PCI help Say 'Y' here if you want your kernel to support the ADI Engineering Coyote Gateway Reference Platform. For more @@ -32,6 +35,7 @@ config ARCH_ADI_COYOTE config ARCH_IXDP425 bool "IXDP425" + select PCI help Say 'Y' here if you want your kernel to support Intel's IXDP425 Development Platform (Also known as Richfield). @@ -39,6 +43,7 @@ config ARCH_IXDP425 config MACH_IXDPG425 bool "IXDPG425" + select PCI help Say 'Y' here if you want your kernel to support Intel's IXDPG425 Development Platform (Also known as Montajade). @@ -46,6 +51,7 @@ config MACH_IXDPG425 config MACH_IXDP465 bool "IXDP465" + select PCI help Say 'Y' here if you want your kernel to support Intel's IXDP465 Development Platform (Also known as BMP). @@ -72,6 +78,7 @@ config ARCH_PRPMC1100 config MACH_NAS100D bool prompt "NAS100D" + select PCI help Say 'Y' here if you want your kernel to support Iomega's NAS 100d device. For more information on this platform, @@ -96,6 +103,7 @@ config CPU_IXP46X config MACH_GTWX5715 bool "Gemtek WX5715 (Linksys WRV54G)" depends on ARCH_IXP4XX + select PCI help This board is currently inside the Linksys WRV54G Gateways. @@ -110,11 +118,16 @@ config MACH_GTWX5715 "High Speed" UART is n/c (as far as I can tell) 20 Pin ARM/Xscale JTAG interface on J2 - comment "IXP4xx Options" +config DMABOUNCE + bool + default y + depends on PCI + config IXP4XX_INDIRECT_PCI bool "Use indirect PCI memory access" + depends on PCI help IXP4xx provides two methods of accessing PCI memory space: diff --git a/arch/arm/mach-ixp4xx/Makefile b/arch/arm/mach-ixp4xx/Makefile index 0471044fa17..5a4aaa0e0a0 100644 --- a/arch/arm/mach-ixp4xx/Makefile +++ b/arch/arm/mach-ixp4xx/Makefile @@ -2,8 +2,9 @@ # Makefile for the linux kernel. # -obj-y += common.o common-pci.o +obj-y += common.o +obj-$(CONFIG_PCI) += common-pci.o obj-$(CONFIG_ARCH_IXDP4XX) += ixdp425-pci.o ixdp425-setup.o obj-$(CONFIG_MACH_IXDPG425) += ixdpg425-pci.o coyote-setup.o obj-$(CONFIG_ARCH_ADI_COYOTE) += coyote-pci.o coyote-setup.o diff --git a/arch/arm/mach-pxa/dma.c b/arch/arm/mach-pxa/dma.c index 458112b21e2..7d8c85486c6 100644 --- a/arch/arm/mach-pxa/dma.c +++ b/arch/arm/mach-pxa/dma.c @@ -45,23 +45,16 @@ int pxa_request_dma (char *name, pxa_dma_prio prio, local_irq_save(flags); - /* try grabbing a DMA channel with the requested priority */ - for (i = prio; i < prio + PXA_DMA_NBCH(prio); i++) { - if (!dma_channels[i].name) { - found = 1; - break; - } - } - - if (!found) { - /* requested prio group is full, try hier priorities */ - for (i = prio-1; i >= 0; i--) { + do { + /* try grabbing a DMA channel with the requested priority */ + pxa_for_each_dma_prio (i, prio) { if (!dma_channels[i].name) { found = 1; break; } } - } + /* if requested prio group is full, try a hier priority */ + } while (!found && prio--); if (found) { DCSR(i) = DCSR_STARTINTR|DCSR_ENDINTR|DCSR_BUSERR; diff --git a/arch/arm/mach-sa1100/irq.c b/arch/arm/mach-sa1100/irq.c index c131a5201b5..b3a56024182 100644 --- a/arch/arm/mach-sa1100/irq.c +++ b/arch/arm/mach-sa1100/irq.c @@ -199,10 +199,26 @@ static void sa1100_unmask_irq(unsigned int irq) ICMR |= (1 << irq); } +/* + * Apart form GPIOs, only the RTC alarm can be a wakeup event. + */ +static int sa1100_set_wake(unsigned int irq, unsigned int on) +{ + if (irq == IRQ_RTCAlrm) { + if (on) + PWER |= PWER_RTC; + else + PWER &= ~PWER_RTC; + return 0; + } + return -EINVAL; +} + static struct irqchip sa1100_normal_chip = { .ack = sa1100_mask_irq, .mask = sa1100_mask_irq, .unmask = sa1100_unmask_irq, + .set_wake = sa1100_set_wake, }; static struct resource irq_resource = { diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types index 8ab5300dcb9..6d7de9c0412 100644 --- a/arch/arm/tools/mach-types +++ b/arch/arm/tools/mach-types @@ -12,7 +12,7 @@ # # http://www.arm.linux.org.uk/developer/machines/?action=new # -# Last update: Mon Feb 20 10:18:02 2006 +# Last update: Mon May 8 20:11:05 2006 # # machine_is_xxx CONFIG_xxxx MACH_TYPE_xxx number # @@ -566,8 +566,8 @@ switchgrass MACH_SWITCHGRASS SWITCHGRASS 549 ens_cmu MACH_ENS_CMU ENS_CMU 550 mm6_sdb MACH_MM6_SDB MM6_SDB 551 saturn MACH_SATURN SATURN 552 -argonplusevb MACH_ARGONPLUSEVB ARGONPLUSEVB 553 -scma11evb MACH_SCMA11EVB SCMA11EVB 554 +i30030evb MACH_ARGONPLUSEVB ARGONPLUSEVB 553 +mxc27530evb MACH_SCMA11EVB SCMA11EVB 554 smdk2800 MACH_SMDK2800 SMDK2800 555 mtwilson MACH_MTWILSON MTWILSON 556 ziti MACH_ZITI ZITI 557 @@ -647,7 +647,7 @@ sendt MACH_SENDT SENDT 630 mx2jazz MACH_MX2JAZZ MX2JAZZ 631 multiio MACH_MULTIIO MULTIIO 632 hrdisplay MACH_HRDISPLAY HRDISPLAY 633 -scma11bb MACH_SCMA11BB SCMA11BB 634 +mxc27530ads MACH_SCMA11BB SCMA11BB 634 trizeps3 MACH_TRIZEPS3 TRIZEPS3 635 zefeerdza MACH_ZEFEERDZA ZEFEERDZA 636 zefeerdzb MACH_ZEFEERDZB ZEFEERDZB 637 @@ -721,7 +721,7 @@ gp32 MACH_GP32 GP32 706 gem MACH_GEM GEM 707 i858 MACH_I858 I858 708 hx2750 MACH_HX2750 HX2750 709 -zeusevb MACH_ZEUSEVB ZEUSEVB 710 +mxc91131evb MACH_ZEUSEVB ZEUSEVB 710 p700 MACH_P700 P700 711 cpe MACH_CPE CPE 712 spitz MACH_SPITZ SPITZ 713 @@ -802,7 +802,7 @@ cpuat91 MACH_CPUAT91 CPUAT91 787 rea9200 MACH_REA9200 REA9200 788 acts_pune_sa1110 MACH_ACTS_PUNE_SA1110 ACTS_PUNE_SA1110 789 ixp425 MACH_IXP425 IXP425 790 -argonplusodyssey MACH_ARGONPLUSODYSSEY ARGONPLUSODYSSEY 791 +i30030ads MACH_ARGONPLUSODYSSEY ARGONPLUSODYSSEY 791 perch MACH_PERCH PERCH 792 eis05r1 MACH_EIS05R1 EIS05R1 793 pepperpad MACH_PEPPERPAD PEPPERPAD 794 @@ -827,7 +827,7 @@ micro9l MACH_MICRO9L MICRO9L 812 uc5471dsp MACH_UC5471DSP UC5471DSP 813 sj5471eng MACH_SJ5471ENG SJ5471ENG 814 none MACH_CMPXA26X CMPXA26X 815 -nc MACH_NC NC 816 +nc1 MACH_NC NC 816 omap_palmte MACH_OMAP_PALMTE OMAP_PALMTE 817 ajax52x MACH_AJAX52X AJAX52X 818 siriustar MACH_SIRIUSTAR SIRIUSTAR 819 @@ -930,7 +930,7 @@ netclient MACH_NETCLIENT NETCLIENT 916 xscale_palmtt5 MACH_XSCALE_PALMTT5 XSCALE_PALMTT5 917 xscale_palmtc MACH_OMAP_PALMTC OMAP_PALMTC 918 omap_apollon MACH_OMAP_APOLLON OMAP_APOLLON 919 -argonlvevb MACH_ARGONLVEVB ARGONLVEVB 920 +mxc30030evb MACH_ARGONLVEVB ARGONLVEVB 920 rea_2d MACH_REA_2D REA_2D 921 eti3e524 MACH_TI3E524 TI3E524 922 ateb9200 MACH_ATEB9200 ATEB9200 923 @@ -965,7 +965,78 @@ sisteron MACH_SISTERON SISTERON 951 rx1950 MACH_RX1950 RX1950 952 tsc_venus MACH_TSC_VENUS TSC_VENUS 953 ds101j MACH_DS101J DS101J 954 -mxc300_30ads MACH_MXC30030ADS MXC30030ADS 955 +mxc30030ads MACH_MXC30030ADS MXC30030ADS 955 fujitsu_wimaxsoc MACH_FUJITSU_WIMAXSOC FUJITSU_WIMAXSOC 956 dualpcmodem MACH_DUALPCMODEM DUALPCMODEM 957 gesbc9312 MACH_GESBC9312 GESBC9312 958 +htcapache MACH_HTCAPACHE HTCAPACHE 959 +ixdp435 MACH_IXDP435 IXDP435 960 +catprovt100 MACH_CATPROVT100 CATPROVT100 961 +picotux1xx MACH_PICOTUX1XX PICOTUX1XX 962 +picotux2xx MACH_PICOTUX2XX PICOTUX2XX 963 +dsmg600 MACH_DSMG600 DSMG600 964 +empc2 MACH_EMPC2 EMPC2 965 +ventura MACH_VENTURA VENTURA 966 +phidget_sbc MACH_PHIDGET_SBC PHIDGET_SBC 967 +ij3k MACH_IJ3K IJ3K 968 +pisgah MACH_PISGAH PISGAH 969 +omap_fsample MACH_OMAP_FSAMPLE OMAP_FSAMPLE 970 +sg720 MACH_SG720 SG720 971 +redfox MACH_REDFOX REDFOX 972 +mysh_ep9315_1 MACH_MYSH_EP9315_1 MYSH_EP9315_1 973 +tpf106 MACH_TPF106 TPF106 974 +at91rm9200kg MACH_AT91RM9200KG AT91RM9200KG 975 +racemt2 MACH_SLEDB SLEDB 976 +ontrack MACH_ONTRACK ONTRACK 977 +pm1200 MACH_PM1200 PM1200 978 +ess24562 MACH_ESS24XXX ESS24XXX 979 +coremp7 MACH_COREMP7 COREMP7 980 +nexcoder_6446 MACH_NEXCODER_6446 NEXCODER_6446 981 +stvc8380 MACH_STVC8380 STVC8380 982 +teklynx MACH_TEKLYNX TEKLYNX 983 +carbonado MACH_CARBONADO CARBONADO 984 +sysmos_mp730 MACH_SYSMOS_MP730 SYSMOS_MP730 985 +snapper_cl15 MACH_SNAPPER_CL15 SNAPPER_CL15 986 +pgigim MACH_PGIGIM PGIGIM 987 +ptx9160p2 MACH_PTX9160P2 PTX9160P2 988 +dcore1 MACH_DCORE1 DCORE1 989 +victorpxa MACH_VICTORPXA VICTORPXA 990 +mx2dtb MACH_MX2DTB MX2DTB 991 +pxa_irex_er0100 MACH_PXA_IREX_ER0100 PXA_IREX_ER0100 992 +omap_palmz71 MACH_OMAP_PALMZ71 OMAP_PALMZ71 993 +bartec_deg MACH_BARTEC_DEG BARTEC_DEG 994 +hw50251 MACH_HW50251 HW50251 995 +ibox MACH_IBOX IBOX 996 +atlaslh7a404 MACH_ATLASLH7A404 ATLASLH7A404 997 +pt2026 MACH_PT2026 PT2026 998 +htcalpine MACH_HTCALPINE HTCALPINE 999 +bartec_vtu MACH_BARTEC_VTU BARTEC_VTU 1000 +vcoreii MACH_VCOREII VCOREII 1001 +pdnb3 MACH_PDNB3 PDNB3 1002 +htcbeetles MACH_HTCBEETLES HTCBEETLES 1003 +s3c6400 MACH_S3C6400 S3C6400 1004 +s3c2443 MACH_S3C2443 S3C2443 1005 +omap_ldk MACH_OMAP_LDK OMAP_LDK 1006 +smdk2460 MACH_SMDK2460 SMDK2460 1007 +smdk2440 MACH_SMDK2440 SMDK2440 1008 +smdk2412 MACH_SMDK2412 SMDK2412 1009 +webbox MACH_WEBBOX WEBBOX 1010 +cwwndp MACH_CWWNDP CWWNDP 1011 +dragon MACH_DRAGON DRAGON 1012 +opendo_cpu_board MACH_OPENDO_CPU_BOARD OPENDO_CPU_BOARD 1013 +ccm2200 MACH_CCM2200 CCM2200 1014 +etwarm MACH_ETWARM ETWARM 1015 +m93030 MACH_M93030 M93030 1016 +cc7u MACH_CC7U CC7U 1017 +mtt_ranger MACH_MTT_RANGER MTT_RANGER 1018 +nexus MACH_NEXUS NEXUS 1019 +desman MACH_DESMAN DESMAN 1020 +bkde303 MACH_BKDE303 BKDE303 1021 +smdk2413 MACH_SMDK2413 SMDK2413 1022 +aml_m7200 MACH_AML_M7200 AML_M7200 1023 +aml_m5900 MACH_AML_M5900 AML_M5900 1024 +sg640 MACH_SG640 SG640 1025 +edg79524 MACH_EDG79524 EDG79524 1026 +ai2410 MACH_AI2410 AI2410 1027 +ixp465 MACH_IXP465 IXP465 1028 +balloon3 MACH_BALLOON3 BALLOON3 1029 diff --git a/arch/arm/vfp/vfpmodule.c b/arch/arm/vfp/vfpmodule.c index 37ff8145b5b..03486be0419 100644 --- a/arch/arm/vfp/vfpmodule.c +++ b/arch/arm/vfp/vfpmodule.c @@ -245,7 +245,7 @@ void VFP9_bounce(u32 trigger, u32 fpexc, struct pt_regs *regs) */ barrier(); trigger = fmrx(FPINST2); - fpscr = fmrx(FPSCR); + orig_fpscr = fpscr = fmrx(FPSCR); emulate: exceptions = vfp_emulate_instruction(trigger, fpscr, regs); diff --git a/arch/i386/Kconfig b/arch/i386/Kconfig index 18ec9fe6deb..c6fe99e57a0 100644 --- a/arch/i386/Kconfig +++ b/arch/i386/Kconfig @@ -467,7 +467,7 @@ endchoice choice depends on EXPERIMENTAL && !X86_PAE - prompt "Memory split" + prompt "Memory split" if EMBEDDED default VMSPLIT_3G help Select the desired split between kernel and user memory. @@ -756,7 +756,7 @@ config PHYSICAL_START config HOTPLUG_CPU bool "Support for hot-pluggable CPUs (EXPERIMENTAL)" - depends on SMP && HOTPLUG && EXPERIMENTAL && !X86_VOYAGER && !X86_PC + depends on SMP && HOTPLUG && EXPERIMENTAL && !X86_VOYAGER ---help--- Say Y here to experiment with turning CPUs off and on. CPUs can be controlled through /sys/devices/system/cpu. diff --git a/arch/i386/kernel/acpi/boot.c b/arch/i386/kernel/acpi/boot.c index 049a2558379..40e5aba3ad3 100644 --- a/arch/i386/kernel/acpi/boot.c +++ b/arch/i386/kernel/acpi/boot.c @@ -215,7 +215,7 @@ static int __init acpi_parse_madt(unsigned long phys_addr, unsigned long size) { struct acpi_table_madt *madt = NULL; - if (!phys_addr || !size || !cpu_has_apic) + if (!phys_addr || !size) return -EINVAL; madt = (struct acpi_table_madt *)__acpi_map_table(phys_addr, size); @@ -1102,9 +1102,6 @@ int __init acpi_boot_table_init(void) dmi_check_system(acpi_dmi_table); #endif - if (!cpu_has_apic) - return -ENODEV; - /* * If acpi_disabled, bail out * One exception: acpi=ht continues far enough to enumerate LAPICs diff --git a/arch/i386/kernel/apic.c b/arch/i386/kernel/apic.c index 254cee9f0b7..013b85df18c 100644 --- a/arch/i386/kernel/apic.c +++ b/arch/i386/kernel/apic.c @@ -757,10 +757,6 @@ static int __init apic_set_verbosity(char *str) apic_verbosity = APIC_DEBUG; else if (strcmp("verbose", str) == 0) apic_verbosity = APIC_VERBOSE; - else - printk(KERN_WARNING "APIC Verbosity level %s not recognised" - " use apic=verbose or apic=debug\n", str); - return 1; } diff --git a/arch/i386/kernel/io_apic.c b/arch/i386/kernel/io_apic.c index f8f132aa547..d70f2ade5cd 100644 --- a/arch/i386/kernel/io_apic.c +++ b/arch/i386/kernel/io_apic.c @@ -2238,6 +2238,8 @@ static inline void unlock_ExtINT_logic(void) spin_unlock_irqrestore(&ioapic_lock, flags); } +int timer_uses_ioapic_pin_0; + /* * This code may look a bit paranoid, but it's supposed to cooperate with * a wide range of boards and BIOS bugs. Fortunately only the timer IRQ @@ -2274,6 +2276,9 @@ static inline void check_timer(void) pin2 = ioapic_i8259.pin; apic2 = ioapic_i8259.apic; + if (pin1 == 0) + timer_uses_ioapic_pin_0 = 1; + printk(KERN_INFO "..TIMER: vector=0x%02X apic1=%d pin1=%d apic2=%d pin2=%d\n", vector, apic1, pin1, apic2, pin2); diff --git a/arch/i386/kernel/kprobes.c b/arch/i386/kernel/kprobes.c index 043f5292e70..38806f42784 100644 --- a/arch/i386/kernel/kprobes.c +++ b/arch/i386/kernel/kprobes.c @@ -242,10 +242,6 @@ static int __kprobes kprobe_handler(struct pt_regs *regs) kcb->kprobe_status = KPROBE_REENTER; return 1; } else { - if (regs->eflags & VM_MASK) { - /* We are in virtual-8086 mode. Return 0 */ - goto no_kprobe; - } if (*addr != BREAKPOINT_INSTRUCTION) { /* The breakpoint instruction was removed by * another cpu right after we hit, no further @@ -265,11 +261,6 @@ static int __kprobes kprobe_handler(struct pt_regs *regs) p = get_kprobe(addr); if (!p) { - if (regs->eflags & VM_MASK) { - /* We are in virtual-8086 mode. Return 0 */ - goto no_kprobe; - } - if (*addr != BREAKPOINT_INSTRUCTION) { /* * The breakpoint instruction was removed right @@ -452,10 +443,11 @@ static void __kprobes resume_execution(struct kprobe *p, *tos &= ~(TF_MASK | IF_MASK); *tos |= kcb->kprobe_old_eflags; break; - case 0xc3: /* ret/lret */ - case 0xcb: - case 0xc2: + case 0xc2: /* iret/ret/lret */ + case 0xc3: case 0xca: + case 0xcb: + case 0xcf: case 0xea: /* jmp absolute -- eip is correct */ /* eip is already adjusted, no more changes required */ p->ainsn.boostable = 1; @@ -463,10 +455,13 @@ static void __kprobes resume_execution(struct kprobe *p, case 0xe8: /* call relative - Fix return addr */ *tos = orig_eip + (*tos - copy_eip); break; + case 0x9a: /* call absolute -- same as call absolute, indirect */ + *tos = orig_eip + (*tos - copy_eip); + goto no_change; case 0xff: if ((p->ainsn.insn[1] & 0x30) == 0x10) { - /* call absolute, indirect */ /* + * call absolute, indirect * Fix return addr; eip is correct. * But this is not boostable */ diff --git a/arch/i386/kernel/mpparse.c b/arch/i386/kernel/mpparse.c index 34d21e21e01..6b1392d33ed 100644 --- a/arch/i386/kernel/mpparse.c +++ b/arch/i386/kernel/mpparse.c @@ -1130,7 +1130,17 @@ int mp_register_gsi (u32 gsi, int triggering, int polarity) */ int irq = gsi; if (gsi < MAX_GSI_NUM) { - if (gsi > 15) + /* + * Retain the VIA chipset work-around (gsi > 15), but + * avoid a problem where the 8254 timer (IRQ0) is setup + * via an override (so it's not on pin 0 of the ioapic), + * and at the same time, the pin 0 interrupt is a PCI + * type. The gsi > 15 test could cause these two pins + * to be shared as IRQ0, and they are not shareable. + * So test for this condition, and if necessary, avoid + * the pin collision. + */ + if (gsi > 15 || (gsi == 0 && !timer_uses_ioapic_pin_0)) gsi = pci_irq++; /* * Don't assign IRQ used by ACPI SCI diff --git a/arch/i386/kernel/ptrace.c b/arch/i386/kernel/ptrace.c index 506462ef36a..fd7eaf7866e 100644 --- a/arch/i386/kernel/ptrace.c +++ b/arch/i386/kernel/ptrace.c @@ -671,7 +671,7 @@ int do_syscall_trace(struct pt_regs *regs, int entryexit) if (unlikely(current->audit_context)) { if (entryexit) - audit_syscall_exit(current, AUDITSC_RESULT(regs->eax), + audit_syscall_exit(AUDITSC_RESULT(regs->eax), regs->eax); /* Debug traps, when using PTRACE_SINGLESTEP, must be sent only * on the syscall exit path. Normally, when TIF_SYSCALL_AUDIT is @@ -720,14 +720,13 @@ int do_syscall_trace(struct pt_regs *regs, int entryexit) ret = is_sysemu; out: if (unlikely(current->audit_context) && !entryexit) - audit_syscall_entry(current, AUDIT_ARCH_I386, regs->orig_eax, + audit_syscall_entry(AUDIT_ARCH_I386, regs->orig_eax, regs->ebx, regs->ecx, regs->edx, regs->esi); if (ret == 0) return 0; regs->orig_eax = -1; /* force skip of syscall restarting */ if (unlikely(current->audit_context)) - audit_syscall_exit(current, AUDITSC_RESULT(regs->eax), - regs->eax); + audit_syscall_exit(AUDITSC_RESULT(regs->eax), regs->eax); return 1; } diff --git a/arch/i386/kernel/setup.c b/arch/i386/kernel/setup.c index 80cb3b2d099..d77e89ac0d5 100644 --- a/arch/i386/kernel/setup.c +++ b/arch/i386/kernel/setup.c @@ -970,8 +970,10 @@ efi_memory_present_wrapper(unsigned long start, unsigned long end, void *arg) * not-overlapping, which is the case */ int __init -e820_all_mapped(unsigned long start, unsigned long end, unsigned type) +e820_all_mapped(unsigned long s, unsigned long e, unsigned type) { + u64 start = s; + u64 end = e; int i; for (i = 0; i < e820.nr_map; i++) { struct e820entry *ei = &e820.map[i]; diff --git a/arch/i386/kernel/smpboot.c b/arch/i386/kernel/smpboot.c index a6969903f2d..825b2b4ca72 100644 --- a/arch/i386/kernel/smpboot.c +++ b/arch/i386/kernel/smpboot.c @@ -313,7 +313,9 @@ static void __init synchronize_tsc_bp (void) if (tsc_values[i] < avg) realdelta = -realdelta; - printk(KERN_INFO "CPU#%d had %ld usecs TSC skew, fixed it up.\n", i, realdelta); + if (realdelta > 0) + printk(KERN_INFO "CPU#%d had %ld usecs TSC " + "skew, fixed it up.\n", i, realdelta); } sum += delta; diff --git a/arch/i386/kernel/timers/timer_tsc.c b/arch/i386/kernel/timers/timer_tsc.c index 5e41ee29c8c..f1187ddb0d0 100644 --- a/arch/i386/kernel/timers/timer_tsc.c +++ b/arch/i386/kernel/timers/timer_tsc.c @@ -279,7 +279,7 @@ time_cpufreq_notifier(struct notifier_block *nb, unsigned long val, { struct cpufreq_freqs *freq = data; - if (val != CPUFREQ_RESUMECHANGE) + if (val != CPUFREQ_RESUMECHANGE && val != CPUFREQ_SUSPENDCHANGE) write_seqlock_irq(&xtime_lock); if (!ref_freq) { if (!freq->old){ @@ -312,7 +312,7 @@ time_cpufreq_notifier(struct notifier_block *nb, unsigned long val, } end: - if (val != CPUFREQ_RESUMECHANGE) + if (val != CPUFREQ_RESUMECHANGE && val != CPUFREQ_SUSPENDCHANGE) write_sequnlock_irq(&xtime_lock); return 0; diff --git a/arch/i386/kernel/vm86.c b/arch/i386/kernel/vm86.c index aee14fafd13..00e0118e717 100644 --- a/arch/i386/kernel/vm86.c +++ b/arch/i386/kernel/vm86.c @@ -312,7 +312,7 @@ static void do_sys_vm86(struct kernel_vm86_struct *info, struct task_struct *tsk /*call audit_syscall_exit since we do not exit via the normal paths */ if (unlikely(current->audit_context)) - audit_syscall_exit(current, AUDITSC_RESULT(eax), eax); + audit_syscall_exit(AUDITSC_RESULT(eax), eax); __asm__ __volatile__( "movl %0,%%esp\n\t" diff --git a/arch/i386/pci/irq.c b/arch/i386/pci/irq.c index 73235443fda..06dab00aaad 100644 --- a/arch/i386/pci/irq.c +++ b/arch/i386/pci/irq.c @@ -591,7 +591,6 @@ static __init int via_router_probe(struct irq_router *r, case PCI_DEVICE_ID_VIA_8233A: case PCI_DEVICE_ID_VIA_8235: case PCI_DEVICE_ID_VIA_8237: - case PCI_DEVICE_ID_VIA_8237_SATA: /* FIXME: add new ones for 8233/5 */ r->name = "VIA"; r->get = pirq_via_get; diff --git a/arch/ia64/Kconfig b/arch/ia64/Kconfig index 9f40eeff0b5..0f3076a820c 100644 --- a/arch/ia64/Kconfig +++ b/arch/ia64/Kconfig @@ -413,6 +413,8 @@ config IA64_PALINFO config SGI_SN def_bool y if (IA64_SGI_SN2 || IA64_GENERIC) +source "drivers/sn/Kconfig" + source "drivers/firmware/Kconfig" source "fs/Kconfig.binfmt" diff --git a/arch/ia64/configs/sn2_defconfig b/arch/ia64/configs/sn2_defconfig index a718034d68d..f6a8853cd1b 100644 --- a/arch/ia64/configs/sn2_defconfig +++ b/arch/ia64/configs/sn2_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc5 -# Mon Feb 27 16:06:38 2006 +# Linux kernel version: 2.6.17-rc3 +# Thu Apr 27 11:48:23 2006 # # @@ -24,6 +24,7 @@ CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_CPUSETS=y +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" CONFIG_CC_OPTIMIZE_FOR_SIZE=y # CONFIG_EMBEDDED is not set @@ -38,10 +39,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -53,7 +50,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_KMOD=y @@ -62,6 +58,7 @@ CONFIG_STOP_MACHINE=y # # Block layer # +# CONFIG_BLK_DEV_IO_TRACE is not set # # IO Schedulers @@ -84,8 +81,10 @@ CONFIG_64BIT=y CONFIG_MMU=y CONFIG_SWIOTLB=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_TIME_INTERPOLATION=y +CONFIG_DMI=y CONFIG_EFI=y CONFIG_GENERIC_IOMAP=y CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y @@ -116,7 +115,6 @@ CONFIG_IA64_SGI_SN_XP=m CONFIG_FORCE_MAX_ZONEORDER=17 CONFIG_SMP=y CONFIG_NR_CPUS=1024 -CONFIG_IA64_NR_NODES=256 # CONFIG_HOTPLUG_CPU is not set CONFIG_SCHED_SMT=y CONFIG_PREEMPT=y @@ -136,6 +134,7 @@ CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_SPARSEMEM_ENABLE=y CONFIG_ARCH_DISCONTIGMEM_DEFAULT=y CONFIG_NUMA=y +CONFIG_NODES_SHIFT=8 CONFIG_VIRTUAL_MEM_MAP=y CONFIG_HOLES_IN_ZONE=y CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID=y @@ -187,7 +186,6 @@ CONFIG_ACPI_SYSTEM=y CONFIG_PCI=y CONFIG_PCI_DOMAINS=y # CONFIG_PCI_MSI is not set -CONFIG_PCI_LEGACY_PROC=y # CONFIG_PCI_DEBUG is not set # @@ -231,6 +229,7 @@ CONFIG_SYN_COOKIES=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=m CONFIG_INET_TCP_DIAG=m @@ -238,9 +237,11 @@ CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_BIC=y CONFIG_IPV6=m # CONFIG_IPV6_PRIVACY is not set +# CONFIG_IPV6_ROUTER_PREF is not set # CONFIG_INET6_AH is not set # CONFIG_INET6_ESP is not set # CONFIG_INET6_IPCOMP is not set +# CONFIG_INET6_XFRM_TUNNEL is not set # CONFIG_INET6_TUNNEL is not set # CONFIG_IPV6_TUNNEL is not set # CONFIG_NETFILTER is not set @@ -468,9 +469,14 @@ CONFIG_SCSI_SATA_VITESSE=y # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set -# CONFIG_SCSI_QLOGIC_FC is not set CONFIG_SCSI_QLOGIC_1280=y -# CONFIG_SCSI_QLA_FC is not set +CONFIG_SCSI_QLA_FC=y +CONFIG_SCSI_QLA2XXX_EMBEDDED_FIRMWARE=y +# CONFIG_SCSI_QLA21XX is not set +CONFIG_SCSI_QLA22XX=y +CONFIG_SCSI_QLA2300=y +CONFIG_SCSI_QLA2322=y +# CONFIG_SCSI_QLA24XX is not set # CONFIG_SCSI_LPFC is not set # CONFIG_SCSI_DC395x is not set # CONFIG_SCSI_DC390T is not set @@ -486,6 +492,7 @@ CONFIG_MD_RAID0=y CONFIG_MD_RAID1=y # CONFIG_MD_RAID10 is not set CONFIG_MD_RAID5=y +# CONFIG_MD_RAID5_RESHAPE is not set # CONFIG_MD_RAID6 is not set CONFIG_MD_MULTIPATH=y # CONFIG_MD_FAULTY is not set @@ -694,6 +701,7 @@ CONFIG_EFI_RTC=y # Ftape, the floppy tape device driver # CONFIG_AGP=y +# CONFIG_AGP_VIA is not set CONFIG_AGP_SGI_TIOCA=y # CONFIG_DRM is not set CONFIG_RAW_DRIVER=m @@ -735,10 +743,6 @@ CONFIG_MMTIMER=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -747,6 +751,7 @@ CONFIG_MMTIMER=y # Digital Video Broadcasting Devices # # CONFIG_DVB is not set +# CONFIG_USB_DABUSB is not set # # Graphics support @@ -757,6 +762,7 @@ CONFIG_MMTIMER=y # Console display driver support # CONFIG_VGA_CONSOLE=y +# CONFIG_VGACON_SOFT_SCROLLBACK is not set CONFIG_DUMMY_CONSOLE=y # @@ -769,6 +775,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=m # CONFIG_USB_DEBUG is not set @@ -829,9 +836,7 @@ CONFIG_USB_HIDINPUT=y # CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set -# CONFIG_USB_MTOUCH is not set -# CONFIG_USB_ITMTOUCH is not set -# CONFIG_USB_EGALAX is not set +# CONFIG_USB_TOUCHSCREEN is not set # CONFIG_USB_YEALINK is not set # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set @@ -846,15 +851,6 @@ CONFIG_USB_HIDINPUT=y # CONFIG_USB_MICROTEK is not set # -# USB Multimedia devices -# -# CONFIG_USB_DABUSB is not set - -# -# Video4Linux support is needed for USB Multimedia device support -# - -# # USB Network Adapters # # CONFIG_USB_CATC is not set @@ -905,15 +901,29 @@ CONFIG_USB_MON=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # CONFIG_INFINIBAND=m # CONFIG_INFINIBAND_USER_MAD is not set CONFIG_INFINIBAND_USER_ACCESS=m CONFIG_INFINIBAND_MTHCA=m -# CONFIG_INFINIBAND_MTHCA_DEBUG is not set +CONFIG_INFINIBAND_MTHCA_DEBUG=y CONFIG_INFINIBAND_IPOIB=m -# CONFIG_INFINIBAND_IPOIB_DEBUG is not set +CONFIG_INFINIBAND_IPOIB_DEBUG=y +# CONFIG_INFINIBAND_IPOIB_DEBUG_DATA is not set CONFIG_INFINIBAND_SRP=m # @@ -923,8 +933,13 @@ CONFIG_SGI_IOC4=y CONFIG_SGI_IOC3=y # -# EDAC - error detection and reporting (RAS) +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -997,7 +1012,6 @@ CONFIG_TMPFS=y CONFIG_HUGETLBFS=y CONFIG_HUGETLB_PAGE=y CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # diff --git a/arch/ia64/ia32/binfmt_elf32.c b/arch/ia64/ia32/binfmt_elf32.c index 4e7a6a1ec6c..da03c06744f 100644 --- a/arch/ia64/ia32/binfmt_elf32.c +++ b/arch/ia64/ia32/binfmt_elf32.c @@ -35,6 +35,9 @@ extern void ia64_elf32_init (struct pt_regs *regs); static void elf32_set_personality (void); +static unsigned long __attribute ((unused)) +randomize_stack_top(unsigned long stack_top); + #define setup_arg_pages(bprm,tos,exec) ia32_setup_arg_pages(bprm,exec) #define elf_map elf32_map diff --git a/arch/ia64/ia32/ia32_entry.S b/arch/ia64/ia32/ia32_entry.S index 95fe04400f6..a32cd59b81e 100644 --- a/arch/ia64/ia32/ia32_entry.S +++ b/arch/ia64/ia32/ia32_entry.S @@ -334,7 +334,7 @@ ia32_syscall_table: data8 sys_setdomainname data8 sys32_newuname data8 sys32_modify_ldt - data8 sys_ni_syscall /* adjtimex */ + data8 compat_sys_adjtimex data8 sys32_mprotect /* 125 */ data8 compat_sys_sigprocmask data8 sys_ni_syscall /* create_module */ diff --git a/arch/ia64/kernel/mca_drv.c b/arch/ia64/kernel/mca_drv.c index 37c88eb5587..ca6666b51cc 100644 --- a/arch/ia64/kernel/mca_drv.c +++ b/arch/ia64/kernel/mca_drv.c @@ -62,6 +62,11 @@ typedef enum { ISOLATE_NONE } isolate_status_t; +typedef enum { + MCA_NOT_RECOVERED = 0, + MCA_RECOVERED = 1 +} recovery_status_t; + /* * This pool keeps pointers to the section part of SAL error record */ @@ -71,6 +76,18 @@ static struct { int max_idx; /* Maximum index of section pointer list pool */ } slidx_pool; +static int +fatal_mca(const char *fmt, ...) +{ + va_list args; + + va_start(args, fmt); + vprintk(fmt, args); + va_end(args); + + return MCA_NOT_RECOVERED; +} + /** * mca_page_isolate - isolate a poisoned page in order not to use it later * @paddr: poisoned memory location @@ -424,7 +441,7 @@ recover_from_read_error(slidx_table_t *slidx, /* Is target address valid? */ if (!pbci->tv) - return 0; + return fatal_mca(KERN_ALERT "MCA: target address not valid\n"); /* * cpu read or memory-mapped io read @@ -442,7 +459,7 @@ recover_from_read_error(slidx_table_t *slidx, /* Is minstate valid? */ if (!peidx_bottom(peidx) || !(peidx_bottom(peidx)->valid.minstate)) - return 0; + return fatal_mca(KERN_ALERT "MCA: minstate not valid\n"); psr1 =(struct ia64_psr *)&(peidx_minstate_area(peidx)->pmsa_ipsr); psr2 =(struct ia64_psr *)&(peidx_minstate_area(peidx)->pmsa_xpsr); @@ -476,12 +493,13 @@ recover_from_read_error(slidx_table_t *slidx, psr2->bn = 1; psr2->i = 0; - return 1; + return MCA_RECOVERED; } } - return 0; + return fatal_mca(KERN_ALERT "MCA: kernel context not recovered," + " iip 0x%lx\n", pmsa->pmsa_iip); } /** @@ -567,13 +585,13 @@ recover_from_processor_error(int platform, slidx_table_t *slidx, * The machine check is corrected. */ if (psp->cm == 1) - return 1; + return MCA_RECOVERED; /* * The error was not contained. Software must be reset. */ if (psp->us || psp->ci == 0) - return 0; + return fatal_mca(KERN_ALERT "MCA: error not contained\n"); /* * The cache check and bus check bits have four possible states @@ -584,20 +602,22 @@ recover_from_processor_error(int platform, slidx_table_t *slidx, * 1 1 Memory error, attempt recovery */ if (psp->bc == 0 || pbci == NULL) - return 0; + return fatal_mca(KERN_ALERT "MCA: No bus check\n"); /* * Sorry, we cannot handle so many. */ if (peidx_bus_check_num(peidx) > 1) - return 0; + return fatal_mca(KERN_ALERT "MCA: Too many bus checks\n"); /* * Well, here is only one bus error. */ - if (pbci->ib || pbci->cc) - return 0; + if (pbci->ib) + return fatal_mca(KERN_ALERT "MCA: Internal Bus error\n"); + if (pbci->cc) + return fatal_mca(KERN_ALERT "MCA: Cache-cache error\n"); if (pbci->eb && pbci->bsi > 0) - return 0; + return fatal_mca(KERN_ALERT "MCA: External bus check fatal status\n"); /* * This is a local MCA and estimated as recoverble external bus error. @@ -609,7 +629,7 @@ recover_from_processor_error(int platform, slidx_table_t *slidx, /* * On account of strange SAL error record, we cannot recover. */ - return 0; + return fatal_mca(KERN_ALERT "MCA: Strange SAL record\n"); } /** @@ -638,12 +658,10 @@ mca_try_to_recover(void *rec, struct ia64_sal_os_state *sos) /* Now, OS can recover when there is one processor error section */ if (n_proc_err > 1) - return 0; - else if (n_proc_err == 0) { + return fatal_mca(KERN_ALERT "MCA: Too Many Errors\n"); + else if (n_proc_err == 0) /* Weird SAL record ... We need not to recover */ - - return 1; - } + return fatal_mca(KERN_ALERT "MCA: Weird SAL record\n"); /* Make index of processor error section */ mca_make_peidx((sal_log_processor_info_t*) @@ -654,7 +672,7 @@ mca_try_to_recover(void *rec, struct ia64_sal_os_state *sos) /* Check whether MCA is global or not */ if (is_mca_global(&peidx, &pbci, sos)) - return 0; + return fatal_mca(KERN_ALERT "MCA: global MCA\n"); /* Try to recover a processor error */ return recover_from_processor_error(platform_err, &slidx, &peidx, diff --git a/arch/ia64/kernel/ptrace.c b/arch/ia64/kernel/ptrace.c index 9887c8787e7..e61e15e28d8 100644 --- a/arch/ia64/kernel/ptrace.c +++ b/arch/ia64/kernel/ptrace.c @@ -1644,7 +1644,7 @@ syscall_trace_enter (long arg0, long arg1, long arg2, long arg3, arch = AUDIT_ARCH_IA64; } - audit_syscall_entry(current, arch, syscall, arg0, arg1, arg2, arg3); + audit_syscall_entry(arch, syscall, arg0, arg1, arg2, arg3); } } @@ -1662,7 +1662,7 @@ syscall_trace_leave (long arg0, long arg1, long arg2, long arg3, if (success != AUDITSC_SUCCESS) result = -result; - audit_syscall_exit(current, success, result); + audit_syscall_exit(success, result); } if (test_thread_flag(TIF_SYSCALL_TRACE) diff --git a/arch/ia64/kernel/topology.c b/arch/ia64/kernel/topology.c index 7da4739f536..4f3a16b37f8 100644 --- a/arch/ia64/kernel/topology.c +++ b/arch/ia64/kernel/topology.c @@ -305,13 +305,10 @@ static struct kobj_type cache_ktype_percpu_entry = { static void __cpuinit cpu_cache_sysfs_exit(unsigned int cpu) { - if (all_cpu_cache_info[cpu].cache_leaves) { - kfree(all_cpu_cache_info[cpu].cache_leaves); - all_cpu_cache_info[cpu].cache_leaves = NULL; - } + kfree(all_cpu_cache_info[cpu].cache_leaves); + all_cpu_cache_info[cpu].cache_leaves = NULL; all_cpu_cache_info[cpu].num_cache_leaves = 0; memset(&all_cpu_cache_info[cpu].kobj, 0, sizeof(struct kobject)); - return; } diff --git a/arch/ia64/lib/memcpy_mck.S b/arch/ia64/lib/memcpy_mck.S index 46c9331e7ab..9e534d52b1d 100644 --- a/arch/ia64/lib/memcpy_mck.S +++ b/arch/ia64/lib/memcpy_mck.S @@ -6,7 +6,9 @@ * in1: source address * in2: number of bytes to copy * Output: - * 0 if success, or number of byte NOT copied if error occurred. + * for memcpy: return dest + * for copy_user: return 0 if success, + * or number of byte NOT copied if error occurred. * * Copyright (C) 2002 Intel Corp. * Copyright (C) 2002 Ken Chen <kenneth.w.chen@intel.com> @@ -73,6 +75,7 @@ GLOBAL_ENTRY(memcpy) and r28=0x7,in0 and r29=0x7,in1 mov f6=f0 + mov retval=in0 br.cond.sptk .common_code ;; END(memcpy) @@ -84,7 +87,7 @@ GLOBAL_ENTRY(__copy_user) mov f6=f1 mov saved_in0=in0 // save dest pointer mov saved_in1=in1 // save src pointer - mov saved_in2=in2 // save len + mov retval=r0 // initialize return value ;; .common_code: cmp.gt p15,p0=8,in2 // check for small size @@ -92,7 +95,7 @@ GLOBAL_ENTRY(__copy_user) cmp.ne p14,p0=0,r29 // check src alignment add src0=0,in1 sub r30=8,r28 // for .align_dest - mov retval=r0 // initialize return value + mov saved_in2=in2 // save len ;; add dst0=0,in0 add dst1=1,in0 // dest odd index diff --git a/arch/ia64/pci/pci.c b/arch/ia64/pci/pci.c index 9ba32b2d96d..ab829a22f8a 100644 --- a/arch/ia64/pci/pci.c +++ b/arch/ia64/pci/pci.c @@ -31,7 +31,6 @@ #include <asm/irq.h> #include <asm/hw_irq.h> - /* * Low-level SAL-based PCI configuration access functions. Note that SAL * calls are already serialized (via sal_lock), so we don't need another @@ -707,7 +706,7 @@ int ia64_pci_legacy_read(struct pci_bus *bus, u16 port, u32 *val, u8 size) * * Simply writes @size bytes of @val to @port. */ -int ia64_pci_legacy_write(struct pci_dev *bus, u16 port, u32 val, u8 size) +int ia64_pci_legacy_write(struct pci_bus *bus, u16 port, u32 val, u8 size) { int ret = size; diff --git a/arch/ia64/sn/kernel/sn2/sn_hwperf.c b/arch/ia64/sn/kernel/sn2/sn_hwperf.c index d917afa30b2..739c948dc50 100644 --- a/arch/ia64/sn/kernel/sn2/sn_hwperf.c +++ b/arch/ia64/sn/kernel/sn2/sn_hwperf.c @@ -284,6 +284,8 @@ static int sn_hwperf_get_nearest_node_objdata(struct sn_hwperf_object_info *objb /* find nearest node with cpus and nearest memory */ for (router=NULL, j=0; j < op->ports; j++) { dest = sn_hwperf_findobj_id(objbuf, nobj, ptdata[j].conn_id); + if (dest && SN_HWPERF_IS_ROUTER(dest)) + router = dest; if (!dest || SN_HWPERF_FOREIGN(dest) || !SN_HWPERF_IS_NODE(dest) || SN_HWPERF_IS_IONODE(dest)) { continue; @@ -299,8 +301,6 @@ static int sn_hwperf_get_nearest_node_objdata(struct sn_hwperf_object_info *objb *near_mem_node = c; found_mem++; } - if (SN_HWPERF_IS_ROUTER(dest)) - router = dest; } if (router && (!found_cpu || !found_mem)) { @@ -493,7 +493,7 @@ static int sn_topology_show(struct seq_file *s, void *d) * numalink ports */ sz = obj->ports * sizeof(struct sn_hwperf_port_info); - if ((ptdata = vmalloc(sz)) == NULL) + if ((ptdata = kmalloc(sz, GFP_KERNEL)) == NULL) return -ENOMEM; e = ia64_sn_hwperf_op(sn_hwperf_master_nasid, SN_HWPERF_ENUM_PORTS, obj->id, sz, @@ -541,7 +541,7 @@ static int sn_topology_show(struct seq_file *s, void *d) (SN_HWPERF_IS_NL3ROUTER(obj) || SN_HWPERF_IS_NL3ROUTER(p)) ? "LLP3" : "LLP4"); } - vfree(ptdata); + kfree(ptdata); } return 0; diff --git a/arch/ia64/sn/kernel/xpc_partition.c b/arch/ia64/sn/kernel/xpc_partition.c index 94211429fd0..2a89cfce495 100644 --- a/arch/ia64/sn/kernel/xpc_partition.c +++ b/arch/ia64/sn/kernel/xpc_partition.c @@ -136,9 +136,7 @@ xpc_get_rsvd_page_pa(int nasid) } if (L1_CACHE_ALIGN(len) > buf_len) { - if (buf_base != NULL) { - kfree(buf_base); - } + kfree(buf_base); buf_len = L1_CACHE_ALIGN(len); buf = (u64) xpc_kmalloc_cacheline_aligned(buf_len, GFP_KERNEL, &buf_base); @@ -159,9 +157,7 @@ xpc_get_rsvd_page_pa(int nasid) } } - if (buf_base != NULL) { - kfree(buf_base); - } + kfree(buf_base); if (status != SALRET_OK) { rp_pa = 0; diff --git a/arch/ia64/sn/pci/tioce_provider.c b/arch/ia64/sn/pci/tioce_provider.c index fa073cc4b56..833295624e5 100644 --- a/arch/ia64/sn/pci/tioce_provider.c +++ b/arch/ia64/sn/pci/tioce_provider.c @@ -682,9 +682,6 @@ tioce_reserve_m32(struct tioce_kernel *ce_kern, u64 base, u64 limit) int ate_index, last_ate, ps; struct tioce *ce_mmr; - if (!TIOCE_M32_ADDR(base)) - return; - ce_mmr = (struct tioce *)ce_kern->ce_common->ce_pcibus.bs_base; ps = ce_kern->ce_ate3240_pagesize; ate_index = ATE_PAGE(base, ps); @@ -693,6 +690,9 @@ tioce_reserve_m32(struct tioce_kernel *ce_kern, u64 base, u64 limit) if (ate_index < 64) ate_index = 64; + if (last_ate >= TIOCE_NUM_M3240_ATES) + last_ate = TIOCE_NUM_M3240_ATES - 1; + while (ate_index <= last_ate) { u64 ate; diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index 87f0b79c6b1..ee5fbb02b28 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -1067,6 +1067,7 @@ choice config CPU_MIPS32_R1 bool "MIPS32 Release 1" depends on SYS_HAS_CPU_MIPS32_R1 + select CPU_HAS_LLSC select CPU_HAS_PREFETCH select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_HIGHMEM @@ -1084,6 +1085,7 @@ config CPU_MIPS32_R1 config CPU_MIPS32_R2 bool "MIPS32 Release 2" depends on SYS_HAS_CPU_MIPS32_R2 + select CPU_HAS_LLSC select CPU_HAS_PREFETCH select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_HIGHMEM @@ -1097,6 +1099,7 @@ config CPU_MIPS32_R2 config CPU_MIPS64_R1 bool "MIPS64 Release 1" depends on SYS_HAS_CPU_MIPS64_R1 + select CPU_HAS_LLSC select CPU_HAS_PREFETCH select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_64BIT_KERNEL @@ -1115,6 +1118,7 @@ config CPU_MIPS64_R1 config CPU_MIPS64_R2 bool "MIPS64 Release 2" depends on SYS_HAS_CPU_MIPS64_R2 + select CPU_HAS_LLSC select CPU_HAS_PREFETCH select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_64BIT_KERNEL @@ -1129,6 +1133,7 @@ config CPU_MIPS64_R2 config CPU_R3000 bool "R3000" depends on SYS_HAS_CPU_R3000 + select CPU_HAS_WB select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_HIGHMEM help @@ -1158,6 +1163,7 @@ config CPU_VR41XX config CPU_R4300 bool "R4300" depends on SYS_HAS_CPU_R4300 + select CPU_HAS_LLSC select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_64BIT_KERNEL help @@ -1166,6 +1172,7 @@ config CPU_R4300 config CPU_R4X00 bool "R4x00" depends on SYS_HAS_CPU_R4X00 + select CPU_HAS_LLSC select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_64BIT_KERNEL help @@ -1175,6 +1182,7 @@ config CPU_R4X00 config CPU_TX49XX bool "R49XX" depends on SYS_HAS_CPU_TX49XX + select CPU_HAS_LLSC select CPU_HAS_PREFETCH select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_64BIT_KERNEL @@ -1182,6 +1190,7 @@ config CPU_TX49XX config CPU_R5000 bool "R5000" depends on SYS_HAS_CPU_R5000 + select CPU_HAS_LLSC select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_64BIT_KERNEL help @@ -1190,12 +1199,14 @@ config CPU_R5000 config CPU_R5432 bool "R5432" depends on SYS_HAS_CPU_R5432 + select CPU_HAS_LLSC select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_64BIT_KERNEL config CPU_R6000 bool "R6000" depends on EXPERIMENTAL + select CPU_HAS_LLSC depends on SYS_HAS_CPU_R6000 select CPU_SUPPORTS_32BIT_KERNEL help @@ -1205,6 +1216,7 @@ config CPU_R6000 config CPU_NEVADA bool "RM52xx" depends on SYS_HAS_CPU_NEVADA + select CPU_HAS_LLSC select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_64BIT_KERNEL help @@ -1214,6 +1226,7 @@ config CPU_R8000 bool "R8000" depends on EXPERIMENTAL depends on SYS_HAS_CPU_R8000 + select CPU_HAS_LLSC select CPU_HAS_PREFETCH select CPU_SUPPORTS_64BIT_KERNEL help @@ -1223,6 +1236,7 @@ config CPU_R8000 config CPU_R10000 bool "R10000" depends on SYS_HAS_CPU_R10000 + select CPU_HAS_LLSC select CPU_HAS_PREFETCH select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_64BIT_KERNEL @@ -1233,6 +1247,7 @@ config CPU_R10000 config CPU_RM7000 bool "RM7000" depends on SYS_HAS_CPU_RM7000 + select CPU_HAS_LLSC select CPU_HAS_PREFETCH select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_64BIT_KERNEL @@ -1241,6 +1256,7 @@ config CPU_RM7000 config CPU_RM9000 bool "RM9000" depends on SYS_HAS_CPU_RM9000 + select CPU_HAS_LLSC select CPU_HAS_PREFETCH select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_64BIT_KERNEL @@ -1249,6 +1265,7 @@ config CPU_RM9000 config CPU_SB1 bool "SB1" depends on SYS_HAS_CPU_SB1 + select CPU_HAS_LLSC select CPU_SUPPORTS_32BIT_KERNEL select CPU_SUPPORTS_64BIT_KERNEL select CPU_SUPPORTS_HIGHMEM @@ -1449,6 +1466,8 @@ choice config MIPS_MT_SMTC bool "SMTC: Use all TCs on all VPEs for SMP" + select CPU_MIPSR2_IRQ_VI + select CPU_MIPSR2_SRS select SMP config MIPS_MT_SMP @@ -1514,38 +1533,15 @@ config 64BIT_PHYS_ADDR bool "Support for 64-bit physical address space" depends on (CPU_R4X00 || CPU_R5000 || CPU_RM7000 || CPU_RM9000 || CPU_R10000 || CPU_SB1 || CPU_MIPS32 || CPU_MIPS64) && 32BIT -config CPU_ADVANCED - bool "Override CPU Options" - depends on 32BIT - help - Saying yes here allows you to select support for various features - your CPU may or may not have. Most people should say N here. - config CPU_HAS_LLSC - bool "ll/sc Instructions available" if CPU_ADVANCED - default y if !CPU_ADVANCED && !CPU_R3000 && !CPU_VR41XX && !CPU_TX39XX - help - MIPS R4000 series and later provide the Load Linked (ll) - and Store Conditional (sc) instructions. More information is - available at <http://www.go-ecs.com/mips/miptek1.htm>. - - Say Y here if your CPU has the ll and sc instructions. Say Y here - for better performance, N if you don't know. You must say Y here - for multiprocessor machines. + bool config CPU_HAS_WB - bool "Writeback Buffer available" if CPU_ADVANCED - default y if !CPU_ADVANCED && CPU_R3000 && MACH_DECSTATION - help - Say N here for slightly better performance. You must say Y here for - machines which require flushing of write buffers in software. Saying - Y is the safe option; N may result in kernel malfunction and crashes. - -menu "MIPSR2 Interrupt handling" - depends on CPU_MIPSR2 && CPU_ADVANCED + bool config CPU_MIPSR2_IRQ_VI bool "Vectored interrupt mode" + depends on CPU_MIPSR2 help Vectored interrupt mode allowing faster dispatching of interrupts. The board support code needs to be written to take advantage of this @@ -1555,6 +1551,7 @@ config CPU_MIPSR2_IRQ_VI config CPU_MIPSR2_IRQ_EI bool "External interrupt controller mode" + depends on CPU_MIPSR2 help Extended interrupt mode takes advantage of an external interrupt controller to allow fast dispatching from many possible interrupt @@ -1568,7 +1565,6 @@ config CPU_MIPSR2_SRS Allow the kernel to use shadow register sets for fast interrupts. Interrupt handlers must be specially written to use shadow sets. Say N unless you know that shadow register set upport is needed. -endmenu config CPU_HAS_SYNC bool diff --git a/arch/mips/Kconfig.debug b/arch/mips/Kconfig.debug index d3c5cc3b9c9..515f9e61130 100644 --- a/arch/mips/Kconfig.debug +++ b/arch/mips/Kconfig.debug @@ -6,7 +6,13 @@ config CROSSCOMPILE bool "Are you using a crosscompiler" help Say Y here if you are compiling the kernel on a different - architecture than the one it is intended to run on. + architecture than the one it is intended to run on. This is just a + convenience option which will select the appropriate value for + the CROSS_COMPILE make variable which otherwise has to be passed on + the command line from mips-linux-, mipsel-linux-, mips64-linux- and + mips64el-linux- as appropriate for a particular kernel configuration. + You will have to pass the value for CROSS_COMPILE manually if the + name prefix for your tools is different. config CMDLINE string "Default kernel command string" diff --git a/arch/mips/Makefile b/arch/mips/Makefile index 69b9c1b8faf..133900aca99 100644 --- a/arch/mips/Makefile +++ b/arch/mips/Makefile @@ -615,7 +615,10 @@ LDFLAGS += -m $(ld-emul) ifdef CONFIG_MIPS CHECKFLAGS += $(shell $(CC) $(CFLAGS) -dM -E -xc /dev/null | \ egrep -vw '__GNUC_(MAJOR|MINOR|PATCHLEVEL)__' | \ - sed -e 's/^\#define /-D/' -e 's/ /="/' -e 's/$$/"/') + sed -e 's/^\#define /-D/' -e "s/ /='/" -e "s/$$/'/") +ifdef CONFIG_64BIT +CHECKFLAGS += -m64 +endif endif OBJCOPYFLAGS += --remove-section=.reginfo diff --git a/arch/mips/configs/atlas_defconfig b/arch/mips/configs/atlas_defconfig index 9e1ae953e96..4b080bcb258 100644 --- a/arch/mips/configs/atlas_defconfig +++ b/arch/mips/configs/atlas_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:39:52 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:50:55 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_ATLAS=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -127,11 +129,11 @@ CONFIG_RM7000_CPU_SCACHE=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -149,7 +151,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -165,6 +166,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -178,10 +180,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -193,7 +191,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -202,6 +199,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -221,7 +220,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -249,6 +247,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -281,6 +280,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_AH=m CONFIG_INET_ESP=m CONFIG_INET_IPCOMP=m +CONFIG_INET_XFRM_TUNNEL=m CONFIG_INET_TUNNEL=m CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y @@ -322,9 +322,12 @@ CONFIG_IP_VS_NQ=m CONFIG_IP_VS_FTP=m CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y +CONFIG_IPV6_ROUTER_PREF=y +CONFIG_IPV6_ROUTE_INFO=y CONFIG_INET6_AH=m CONFIG_INET6_ESP=m CONFIG_INET6_IPCOMP=m +CONFIG_INET6_XFRM_TUNNEL=m CONFIG_INET6_TUNNEL=m CONFIG_IPV6_TUNNEL=m CONFIG_NETFILTER=y @@ -348,11 +351,14 @@ CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m CONFIG_NETFILTER_XT_MATCH_CONNMARK=m CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m @@ -376,20 +382,19 @@ CONFIG_IP_NF_IRC=m CONFIG_IP_NF_TFTP=m CONFIG_IP_NF_AMANDA=m CONFIG_IP_NF_PPTP=m +CONFIG_IP_NF_H323=m CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_IPRANGE=m -CONFIG_IP_NF_MATCH_MULTIPORT=m CONFIG_IP_NF_MATCH_TOS=m CONFIG_IP_NF_MATCH_RECENT=m CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_DSCP=m -CONFIG_IP_NF_MATCH_AH_ESP=m +CONFIG_IP_NF_MATCH_AH=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_MATCH_OWNER=m CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_HASHLIMIT=m -CONFIG_IP_NF_MATCH_POLICY=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -407,6 +412,7 @@ CONFIG_IP_NF_NAT_FTP=m CONFIG_IP_NF_NAT_TFTP=m CONFIG_IP_NF_NAT_AMANDA=m CONFIG_IP_NF_NAT_PPTP=m +CONFIG_IP_NF_NAT_H323=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_TOS=m CONFIG_IP_NF_TARGET_ECN=m @@ -427,12 +433,10 @@ CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_FRAG=m CONFIG_IP6_NF_MATCH_HL=m -CONFIG_IP6_NF_MATCH_MULTIPORT=m CONFIG_IP6_NF_MATCH_OWNER=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AHESP=m +CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_MATCH_POLICY=m CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_LOG=m CONFIG_IP6_NF_TARGET_REJECT=m @@ -478,6 +482,11 @@ CONFIG_IP_SCTP=m # CONFIG_SCTP_HMAC_NONE is not set # CONFIG_SCTP_HMAC_SHA1 is not set CONFIG_SCTP_HMAC_MD5=y + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set CONFIG_BRIDGE=m CONFIG_VLAN_8021Q=m @@ -492,11 +501,6 @@ CONFIG_IPDDP_ENCAP=y CONFIG_IPDDP_DECAP=y # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set CONFIG_NET_DIVERT=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -556,6 +560,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -694,9 +701,8 @@ CONFIG_SCSI_SYM53C8XX_2=y CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=0 CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16 CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64 -# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set +CONFIG_SCSI_SYM53C8XX_MMIO=y # CONFIG_SCSI_IPR is not set -# CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_QLOGIC_1280 is not set # CONFIG_SCSI_QLA_FC is not set # CONFIG_SCSI_LPFC is not set @@ -715,6 +721,7 @@ CONFIG_MD_RAID0=m CONFIG_MD_RAID1=m CONFIG_MD_RAID10=m CONFIG_MD_RAID5=m +CONFIG_MD_RAID5_RESHAPE=y CONFIG_MD_RAID6=m CONFIG_MD_MULTIPATH=m CONFIG_MD_FAULTY=m @@ -921,6 +928,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=m CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -930,6 +938,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -988,10 +997,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -1022,6 +1027,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -1039,13 +1045,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -1120,7 +1144,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -1140,7 +1163,6 @@ CONFIG_VXFS_FS=m # CONFIG_QNX4FS_FS is not set CONFIG_SYSV_FS=m CONFIG_UFS_FS=m -# CONFIG_UFS_FS_WRITE is not set # # Network File Systems @@ -1232,6 +1254,7 @@ CONFIG_NLS_UTF8=m # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/bigsur_defconfig b/arch/mips/configs/bigsur_defconfig index 32984100a75..d85cda58d65 100644 --- a/arch/mips/configs/bigsur_defconfig +++ b/arch/mips/configs/bigsur_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:39:53 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:50:55 2006 # CONFIG_MIPS=y @@ -80,6 +80,8 @@ CONFIG_SIBYTE_CFE=y # CONFIG_SIBYTE_SB1250_PROF is not set # CONFIG_SIBYTE_TBPROF is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_COHERENT=y CONFIG_CPU_BIG_ENDIAN=y @@ -154,7 +156,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_LOCK_KERNEL=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -172,6 +173,7 @@ CONFIG_SYSCTL=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y # CONFIG_CPUSETS is not set +# CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -186,10 +188,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -201,7 +199,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -210,6 +207,7 @@ CONFIG_STOP_MACHINE=y # # Block layer # +# CONFIG_BLK_DEV_IO_TRACE is not set # # IO Schedulers @@ -230,7 +228,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_HW_HAS_PCI=y CONFIG_PCI=y CONFIG_PCI_DOMAINS=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_PCI_DEBUG=y CONFIG_MMU=y @@ -249,6 +246,7 @@ CONFIG_MMU=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set +CONFIG_BUILD_ELF64=y CONFIG_MIPS32_COMPAT=y CONFIG_COMPAT=y CONFIG_MIPS32_O32=y @@ -263,6 +261,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -284,12 +283,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -301,6 +303,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -310,11 +317,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -377,7 +379,7 @@ CONFIG_BLK_DEV_LOOP=m CONFIG_BLK_DEV_NBD=m # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set @@ -575,6 +577,7 @@ CONFIG_SIBYTE_SB1250_DUART_CONSOLE=y # # Non-8250 serial port support # +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -637,7 +640,6 @@ CONFIG_I2C_ALGO_SIBYTE=y # CONFIG_I2C_PROSAVAGE is not set # CONFIG_I2C_SAVAGE4 is not set CONFIG_I2C_SIBYTE=y -# CONFIG_SCx200_ACB is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set # CONFIG_I2C_SIS96X is not set @@ -656,9 +658,7 @@ CONFIG_SENSORS_EEPROM=y CONFIG_SENSORS_PCF8574=y CONFIG_SENSORS_PCA9539=y CONFIG_SENSORS_PCF8591=y -CONFIG_SENSORS_RTC8564=y CONFIG_SENSORS_MAX6875=y -# CONFIG_RTC_X1205_I2C is not set CONFIG_I2C_DEBUG_CORE=y CONFIG_I2C_DEBUG_ALGO=y CONFIG_I2C_DEBUG_BUS=y @@ -686,10 +686,6 @@ CONFIG_I2C_DEBUG_CHIP=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -714,6 +710,7 @@ CONFIG_I2C_DEBUG_CHIP=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -731,13 +728,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -785,7 +800,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -# CONFIG_RELAYFS_FS is not set # CONFIG_CONFIGFS_FS is not set # diff --git a/arch/mips/configs/capcella_defconfig b/arch/mips/configs/capcella_defconfig index 6c2961affbd..ca0af1683a0 100644 --- a/arch/mips/configs/capcella_defconfig +++ b/arch/mips/configs/capcella_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:39:54 2006 +# Linux kernel version: 2.6.17-rc2 +# Tue Apr 25 00:08:06 2006 # CONFIG_MIPS=y @@ -72,6 +72,8 @@ CONFIG_ZAO_CAPCELLA=y CONFIG_PCI_VR41XX=y # CONFIG_VRC4173 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -90,7 +92,7 @@ CONFIG_MIPS_L1_CACHE_SHIFT=5 # CONFIG_CPU_MIPS64_R2 is not set # CONFIG_CPU_R3000 is not set # CONFIG_CPU_TX39XX is not set -# CONFIG_CPU_VR41XX is not set +CONFIG_CPU_VR41XX=y # CONFIG_CPU_R4300 is not set # CONFIG_CPU_R4X00 is not set # CONFIG_CPU_TX49XX is not set @@ -103,18 +105,21 @@ CONFIG_MIPS_L1_CACHE_SHIFT=5 # CONFIG_CPU_RM7000 is not set # CONFIG_CPU_RM9000 is not set # CONFIG_CPU_SB1 is not set +CONFIG_SYS_HAS_CPU_VR41XX=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_64BIT_KERNEL=y # # Kernel type # -# CONFIG_32BIT is not set +CONFIG_32BIT=y # CONFIG_64BIT is not set CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_8KB is not set # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y @@ -135,7 +140,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -151,6 +155,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -164,10 +169,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -179,7 +180,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -187,6 +187,9 @@ CONFIG_KMOD=y # # Block layer # +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -206,7 +209,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -224,6 +226,7 @@ CONFIG_MMU=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set +CONFIG_TRAD_SIGNALS=y # # Networking @@ -233,6 +236,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -255,12 +259,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -272,6 +279,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -281,11 +293,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -302,10 +309,7 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_HAMRADIO is not set # CONFIG_IRDA is not set # CONFIG_BT is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m +# CONFIG_IEEE80211 is not set # # Device Drivers @@ -348,10 +352,12 @@ CONFIG_CONNECTOR=m # CONFIG_BLK_DEV_LOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set -# CONFIG_BLK_DEV_RAM is not set +CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +# CONFIG_BLK_DEV_INITRD is not set # CONFIG_CDROM_PKTCDVD is not set -CONFIG_ATA_OVER_ETH=m +# CONFIG_ATA_OVER_ETH is not set # # ATA/ATAPI/MFM/RLL support @@ -578,6 +584,11 @@ CONFIG_HW_CONSOLE=y # # Non-8250 serial port support # +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_SERIAL_VR41XX=y +CONFIG_SERIAL_VR41XX_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -601,6 +612,7 @@ CONFIG_LEGACY_PTY_COUNT=256 # Ftape, the floppy tape device driver # # CONFIG_DRM is not set +CONFIG_GPIO_VR41XX=y # CONFIG_RAW_DRIVER is not set # @@ -636,10 +648,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -670,6 +678,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -687,13 +696,48 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock +# +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y + +# +# RTC drivers # +# CONFIG_RTC_DRV_M48T86 is not set +CONFIG_RTC_DRV_VR41XX=y +# CONFIG_RTC_DRV_TEST is not set # # File systems @@ -712,7 +756,7 @@ CONFIG_EXT2_FS=y CONFIG_INOTIFY=y # CONFIG_QUOTA is not set CONFIG_DNOTIFY=y -CONFIG_AUTOFS_FS=y +# CONFIG_AUTOFS_FS is not set CONFIG_AUTOFS4_FS=y CONFIG_FUSE_FS=m @@ -735,10 +779,9 @@ CONFIG_FUSE_FS=m CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_SYSFS=y -# CONFIG_TMPFS is not set +CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -805,44 +848,20 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="mem=32M console=ttyVR0,38400" # # Security options # -CONFIG_KEYS=y -CONFIG_KEYS_DEBUG_PROC_KEYS=y +# CONFIG_KEYS is not set # CONFIG_SECURITY is not set # # Cryptographic options # -CONFIG_CRYPTO=y -CONFIG_CRYPTO_HMAC=y -CONFIG_CRYPTO_NULL=m -CONFIG_CRYPTO_MD4=m -CONFIG_CRYPTO_MD5=m -CONFIG_CRYPTO_SHA1=m -CONFIG_CRYPTO_SHA256=m -CONFIG_CRYPTO_SHA512=m -CONFIG_CRYPTO_WP512=m -CONFIG_CRYPTO_TGR192=m -CONFIG_CRYPTO_DES=m -CONFIG_CRYPTO_BLOWFISH=m -CONFIG_CRYPTO_TWOFISH=m -CONFIG_CRYPTO_SERPENT=m -CONFIG_CRYPTO_AES=m -CONFIG_CRYPTO_CAST5=m -CONFIG_CRYPTO_CAST6=m -CONFIG_CRYPTO_TEA=m -CONFIG_CRYPTO_ARC4=m -CONFIG_CRYPTO_KHAZAD=m -CONFIG_CRYPTO_ANUBIS=m -CONFIG_CRYPTO_DEFLATE=m -CONFIG_CRYPTO_MICHAEL_MIC=m -CONFIG_CRYPTO_CRC32C=m -# CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO is not set # # Hardware crypto devices @@ -852,8 +871,6 @@ CONFIG_CRYPTO_CRC32C=m # Library routines # # CONFIG_CRC_CCITT is not set -CONFIG_CRC16=m +# CONFIG_CRC16 is not set CONFIG_CRC32=y -CONFIG_LIBCRC32C=m -CONFIG_ZLIB_INFLATE=m -CONFIG_ZLIB_DEFLATE=m +# CONFIG_LIBCRC32C is not set diff --git a/arch/mips/configs/cobalt_defconfig b/arch/mips/configs/cobalt_defconfig index 8336b21d3db..7d269e60928 100644 --- a/arch/mips/configs/cobalt_defconfig +++ b/arch/mips/configs/cobalt_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:39:55 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:50:57 2006 # CONFIG_MIPS=y @@ -63,7 +63,10 @@ CONFIG_MIPS_COBALT=y # CONFIG_TOSHIBA_JMR3927 is not set # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set +CONFIG_EARLY_PRINTK=y CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -113,7 +116,6 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -135,7 +137,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -151,6 +152,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -164,10 +166,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -182,6 +180,8 @@ CONFIG_BASE_SMALL=0 # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -201,7 +201,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -229,6 +228,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -247,12 +247,15 @@ CONFIG_IP_FIB_HASH=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=y +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -264,6 +267,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -273,11 +281,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -298,6 +301,9 @@ CONFIG_IEEE80211=y # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=y CONFIG_IEEE80211_CRYPT_CCMP=y +CONFIG_IEEE80211_SOFTMAC=y +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -343,7 +349,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=y CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -593,6 +599,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -602,6 +609,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -660,10 +668,6 @@ CONFIG_COBALT_LCD=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -694,6 +698,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -711,13 +716,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -765,7 +788,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=y # CONFIG_CONFIGFS_FS is not set # @@ -828,6 +850,8 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set +# CONFIG_UNWIND_INFO is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/db1000_defconfig b/arch/mips/configs/db1000_defconfig index 7f071403c8e..579b665e333 100644 --- a/arch/mips/configs/db1000_defconfig +++ b/arch/mips/configs/db1000_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:39:56 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:50:57 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_DB1000=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -114,11 +116,11 @@ CONFIG_PAGE_SIZE_4KB=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set CONFIG_64BIT_PHYS_ADDR=y -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -136,7 +138,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -152,6 +153,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -165,10 +167,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -181,7 +179,6 @@ CONFIG_OBSOLETE_INTERMODULE=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -190,6 +187,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -245,6 +244,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -267,7 +267,8 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -278,6 +279,8 @@ CONFIG_TCP_CONG_BIC=y # # CONFIG_IP_VS is not set # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set @@ -294,10 +297,13 @@ CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m @@ -321,6 +327,11 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -330,11 +341,6 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -356,6 +362,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -412,7 +421,6 @@ CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_CFI_INTELEXT is not set CONFIG_MTD_CFI_AMDSTD=y -CONFIG_MTD_CFI_AMDSTD_RETRY=0 # CONFIG_MTD_CFI_STAA is not set CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set @@ -434,7 +442,6 @@ CONFIG_MTD_ALCHEMY=y # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLKMTD is not set # CONFIG_MTD_BLOCK2MTD is not set # @@ -471,7 +478,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -722,10 +729,6 @@ CONFIG_SYNCLINK_CS=m # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -756,6 +759,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +# CONFIG_USB_ARCH_HAS_EHCI is not set # CONFIG_USB is not set # @@ -773,12 +777,30 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -836,7 +858,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -945,6 +966,7 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/db1100_defconfig b/arch/mips/configs/db1100_defconfig index 98590cac1ec..e5eb5386742 100644 --- a/arch/mips/configs/db1100_defconfig +++ b/arch/mips/configs/db1100_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:39:57 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:50:58 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_DB1100=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -114,11 +116,11 @@ CONFIG_PAGE_SIZE_4KB=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set CONFIG_64BIT_PHYS_ADDR=y -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -136,7 +138,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -152,6 +153,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -165,10 +167,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -181,7 +179,6 @@ CONFIG_OBSOLETE_INTERMODULE=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -190,6 +187,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -234,6 +233,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -256,7 +256,8 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -267,6 +268,8 @@ CONFIG_TCP_CONG_BIC=y # # CONFIG_IP_VS is not set # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set @@ -283,10 +286,13 @@ CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m @@ -310,6 +316,11 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -319,11 +330,6 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -345,6 +351,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -401,7 +410,6 @@ CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_CFI_INTELEXT is not set CONFIG_MTD_CFI_AMDSTD=y -CONFIG_MTD_CFI_AMDSTD_RETRY=0 # CONFIG_MTD_CFI_STAA is not set CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set @@ -423,7 +431,6 @@ CONFIG_MTD_ALCHEMY=y # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLKMTD is not set # CONFIG_MTD_BLOCK2MTD is not set # @@ -460,7 +467,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -690,10 +697,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -711,6 +714,7 @@ CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_MACMODES is not set +CONFIG_FB_FIRMWARE_EDID=y # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set # CONFIG_FB_S1D13XXX is not set @@ -755,6 +759,7 @@ CONFIG_LOGO_LINUX_CLUT224=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +# CONFIG_USB_ARCH_HAS_EHCI is not set # CONFIG_USB is not set # @@ -772,12 +777,30 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -835,7 +858,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -944,6 +966,7 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/db1200_defconfig b/arch/mips/configs/db1200_defconfig index 92888472dca..a43fb2329fd 100644 --- a/arch/mips/configs/db1200_defconfig +++ b/arch/mips/configs/db1200_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:39:58 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:50:58 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_DB1200=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_COHERENT=y CONFIG_MIPS_DISABLE_OBSOLETE_IDE=y @@ -114,11 +116,11 @@ CONFIG_PAGE_SIZE_4KB=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set CONFIG_64BIT_PHYS_ADDR=y -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -136,7 +138,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -153,6 +154,7 @@ CONFIG_SYSCTL=y # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y +# CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -166,10 +168,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -182,7 +180,6 @@ CONFIG_OBSOLETE_INTERMODULE=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -191,6 +188,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -244,6 +243,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -263,7 +263,8 @@ CONFIG_IP_FIB_HASH=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -274,6 +275,8 @@ CONFIG_TCP_CONG_BIC=y # # CONFIG_IP_VS is not set # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set @@ -288,10 +291,13 @@ CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m @@ -315,6 +321,11 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -324,11 +335,6 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -403,7 +409,6 @@ CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_CFI_INTELEXT is not set CONFIG_MTD_CFI_AMDSTD=y -CONFIG_MTD_CFI_AMDSTD_RETRY=0 # CONFIG_MTD_CFI_STAA is not set CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set @@ -425,7 +430,6 @@ CONFIG_MTD_ALCHEMY=y # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLKMTD is not set # CONFIG_MTD_BLOCK2MTD is not set # @@ -763,10 +767,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -784,6 +784,7 @@ CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_MACMODES is not set +CONFIG_FB_FIRMWARE_EDID=y # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set # CONFIG_FB_S1D13XXX is not set @@ -794,6 +795,7 @@ CONFIG_FB_AU1200=y # Console display driver support # CONFIG_VGA_CONSOLE=y +# CONFIG_VGACON_SOFT_SCROLLBACK is not set CONFIG_DUMMY_CONSOLE=y # CONFIG_FRAMEBUFFER_CONSOLE is not set @@ -816,6 +818,7 @@ CONFIG_LOGO_LINUX_CLUT224=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -832,6 +835,7 @@ CONFIG_USB_GADGET=m # CONFIG_USB_GADGET_GOKU is not set # CONFIG_USB_GADGET_LH7A40X is not set # CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_AT91 is not set # CONFIG_USB_GADGET_DUMMY_HCD is not set # CONFIG_USB_GADGET_DUALSPEED is not set @@ -844,12 +848,30 @@ CONFIG_MMC_BLOCK=y CONFIG_MMC_AU1X=y # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -913,7 +935,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -# CONFIG_RELAYFS_FS is not set # CONFIG_CONFIGFS_FS is not set # @@ -1027,6 +1048,7 @@ CONFIG_NLS_UTF8=m # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="mem=48M" diff --git a/arch/mips/configs/db1500_defconfig b/arch/mips/configs/db1500_defconfig index 5a415b1d4af..ad632d87c4e 100644 --- a/arch/mips/configs/db1500_defconfig +++ b/arch/mips/configs/db1500_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:39:59 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:50:59 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_DB1500=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -116,11 +118,11 @@ CONFIG_PAGE_SIZE_4KB=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set CONFIG_64BIT_PHYS_ADDR=y -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -138,7 +140,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -154,6 +155,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -167,10 +169,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -183,7 +181,6 @@ CONFIG_OBSOLETE_INTERMODULE=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -192,6 +189,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -211,7 +210,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -253,6 +251,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -275,7 +274,8 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -286,6 +286,8 @@ CONFIG_TCP_CONG_BIC=y # # CONFIG_IP_VS is not set # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set @@ -302,10 +304,13 @@ CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m @@ -329,6 +334,11 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -338,11 +348,6 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -364,6 +369,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -420,7 +428,6 @@ CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I8 is not set CONFIG_MTD_CFI_INTELEXT=y CONFIG_MTD_CFI_AMDSTD=y -CONFIG_MTD_CFI_AMDSTD_RETRY=0 # CONFIG_MTD_CFI_STAA is not set CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set @@ -443,7 +450,6 @@ CONFIG_MTD_ALCHEMY=y # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLKMTD is not set # CONFIG_MTD_BLOCK2MTD is not set # @@ -486,7 +492,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_UB is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -714,6 +720,7 @@ CONFIG_SERIO_RAW=m # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y # CONFIG_SERIAL_8250_CS is not set CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 @@ -725,6 +732,7 @@ CONFIG_SERIAL_8250_AU1X00=y # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -790,10 +798,6 @@ CONFIG_SYNCLINK_CS=m # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -802,6 +806,7 @@ CONFIG_SYNCLINK_CS=m # Digital Video Broadcasting Devices # # CONFIG_DVB is not set +# CONFIG_USB_DABUSB is not set # # Graphics support @@ -825,9 +830,11 @@ CONFIG_SND_SEQ_DUMMY=m CONFIG_SND_OSSEMUL=y CONFIG_SND_MIXER_OSS=m CONFIG_SND_PCM_OSS=m +CONFIG_SND_PCM_OSS_PLUGINS=y CONFIG_SND_SEQUENCER_OSS=y # CONFIG_SND_DYNAMIC_MINORS is not set CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set @@ -846,6 +853,7 @@ CONFIG_SND_MTPAV=m # PCI devices # # CONFIG_SND_AD1889 is not set +# CONFIG_SND_ALS300 is not set # CONFIG_SND_ALI5451 is not set # CONFIG_SND_ATIIXP is not set # CONFIG_SND_ATIIXP_MODEM is not set @@ -877,6 +885,7 @@ CONFIG_SND_MTPAV=m # CONFIG_SND_MIXART is not set # CONFIG_SND_NM256 is not set # CONFIG_SND_PCXHR is not set +# CONFIG_SND_RIPTIDE is not set # CONFIG_SND_RME32 is not set # CONFIG_SND_RME96 is not set # CONFIG_SND_RME9652 is not set @@ -905,34 +914,22 @@ CONFIG_SND_AU1X00=m # Open Sound System # CONFIG_SOUND_PRIME=y -CONFIG_OBSOLETE_OSS_DRIVER=y # CONFIG_SOUND_BT878 is not set -# CONFIG_SOUND_CMPCI is not set # CONFIG_SOUND_EMU10K1 is not set # CONFIG_SOUND_FUSION is not set -# CONFIG_SOUND_CS4281 is not set -# CONFIG_SOUND_ES1370 is not set # CONFIG_SOUND_ES1371 is not set -# CONFIG_SOUND_ESSSOLO1 is not set -# CONFIG_SOUND_MAESTRO is not set -# CONFIG_SOUND_MAESTRO3 is not set # CONFIG_SOUND_ICH is not set -# CONFIG_SOUND_SONICVIBES is not set -# CONFIG_SOUND_AU1000 is not set # CONFIG_SOUND_TRIDENT is not set # CONFIG_SOUND_MSNDCLAS is not set # CONFIG_SOUND_MSNDPIN is not set # CONFIG_SOUND_VIA82CXXX is not set -# CONFIG_SOUND_ALI5455 is not set -# CONFIG_SOUND_FORTE is not set -# CONFIG_SOUND_RME96XX is not set -# CONFIG_SOUND_AD1980 is not set # # USB support # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y # CONFIG_USB_DEBUG is not set @@ -958,7 +955,6 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y # # USB Device Class drivers # -# CONFIG_OBSOLETE_OSS_USB_DRIVER is not set # CONFIG_USB_ACM is not set # CONFIG_USB_PRINTER is not set @@ -985,9 +981,7 @@ CONFIG_USB_HIDINPUT=y # CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set -# CONFIG_USB_MTOUCH is not set -# CONFIG_USB_ITMTOUCH is not set -# CONFIG_USB_EGALAX is not set +# CONFIG_USB_TOUCHSCREEN is not set CONFIG_USB_YEALINK=m # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set @@ -1001,15 +995,6 @@ CONFIG_USB_YEALINK=m # CONFIG_USB_MDC800 is not set # -# USB Multimedia devices -# -# CONFIG_USB_DABUSB is not set - -# -# Video4Linux support is needed for USB Multimedia device support -# - -# # USB Network Adapters # # CONFIG_USB_CATC is not set @@ -1059,13 +1044,31 @@ CONFIG_USB_LD=m # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -1123,7 +1126,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -1232,6 +1234,7 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/db1550_defconfig b/arch/mips/configs/db1550_defconfig index 8dc1f18badf..8130e23dc25 100644 --- a/arch/mips/configs/db1550_defconfig +++ b/arch/mips/configs/db1550_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:00 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:00 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_DB1550=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -115,11 +117,11 @@ CONFIG_PAGE_SIZE_4KB=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set CONFIG_64BIT_PHYS_ADDR=y -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -137,7 +139,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -153,6 +154,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -166,10 +168,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -182,7 +180,6 @@ CONFIG_OBSOLETE_INTERMODULE=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -191,6 +188,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -210,7 +209,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -252,6 +250,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -274,7 +273,8 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -285,6 +285,8 @@ CONFIG_TCP_CONG_BIC=y # # CONFIG_IP_VS is not set # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set @@ -301,10 +303,13 @@ CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m @@ -328,6 +333,11 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -337,11 +347,6 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -363,6 +368,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -419,7 +427,6 @@ CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_CFI_INTELEXT is not set CONFIG_MTD_CFI_AMDSTD=y -CONFIG_MTD_CFI_AMDSTD_RETRY=0 # CONFIG_MTD_CFI_STAA is not set CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set @@ -442,7 +449,6 @@ CONFIG_MTD_ALCHEMY=y # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLKMTD is not set # CONFIG_MTD_BLOCK2MTD is not set # @@ -489,7 +495,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -754,6 +760,7 @@ CONFIG_SERIO_RAW=m # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y # CONFIG_SERIAL_8250_CS is not set CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 @@ -765,6 +772,7 @@ CONFIG_SERIAL_8250_AU1X00=y # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -830,10 +838,6 @@ CONFIG_SYNCLINK_CS=m # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -858,6 +862,7 @@ CONFIG_SYNCLINK_CS=m # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -875,13 +880,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -939,7 +962,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -1048,6 +1070,7 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/ddb5476_defconfig b/arch/mips/configs/ddb5476_defconfig index 8fae63e47e5..8d88ac1bbfe 100644 --- a/arch/mips/configs/ddb5476_defconfig +++ b/arch/mips/configs/ddb5476_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:02 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:00 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_DDB5476=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -114,7 +116,6 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -136,7 +137,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -152,6 +152,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -165,10 +166,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -183,6 +180,8 @@ CONFIG_BASE_SMALL=0 # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -202,7 +201,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_ISA=y CONFIG_MMU=y @@ -231,6 +229,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -252,12 +251,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=y +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -269,6 +271,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -278,11 +285,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -303,6 +305,9 @@ CONFIG_IEEE80211=y # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=y CONFIG_IEEE80211_CRYPT_CCMP=y +CONFIG_IEEE80211_SOFTMAC=y +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -348,7 +353,7 @@ CONFIG_PROC_EVENTS=y # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=y CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -571,6 +576,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -580,6 +586,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -638,10 +645,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -659,6 +662,7 @@ CONFIG_FB=y # CONFIG_FB_CFB_COPYAREA is not set # CONFIG_FB_CFB_IMAGEBLIT is not set # CONFIG_FB_MACMODES is not set +CONFIG_FB_FIRMWARE_EDID=y # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set # CONFIG_FB_CIRRUS is not set @@ -670,7 +674,6 @@ CONFIG_FB=y # CONFIG_FB_NVIDIA is not set # CONFIG_FB_RIVA is not set # CONFIG_FB_MATROX is not set -# CONFIG_FB_RADEON_OLD is not set # CONFIG_FB_RADEON is not set # CONFIG_FB_ATY128 is not set # CONFIG_FB_ATY is not set @@ -708,6 +711,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -725,13 +729,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -776,7 +798,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=y # CONFIG_CONFIGFS_FS is not set # @@ -840,6 +861,8 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set +# CONFIG_UNWIND_INFO is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="ip=any" diff --git a/arch/mips/configs/ddb5477_defconfig b/arch/mips/configs/ddb5477_defconfig index a0fcd44e770..8c911b67141 100644 --- a/arch/mips/configs/ddb5477_defconfig +++ b/arch/mips/configs/ddb5477_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:02 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:01 2006 # CONFIG_MIPS=y @@ -65,6 +65,8 @@ CONFIG_DDB5477=y # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_DDB5477_BUS_FREQUENCY=0 CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -114,7 +116,6 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -136,7 +137,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -152,6 +152,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -165,10 +166,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -183,6 +180,8 @@ CONFIG_BASE_SMALL=0 # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -202,7 +201,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -230,6 +228,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -251,12 +250,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=y +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -268,6 +270,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -277,11 +284,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -302,6 +304,9 @@ CONFIG_IEEE80211=y # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=y CONFIG_IEEE80211_CRYPT_CCMP=y +CONFIG_IEEE80211_SOFTMAC=y +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -346,7 +351,7 @@ CONFIG_PROC_EVENTS=y # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=y CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -556,6 +561,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -565,6 +571,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -623,10 +630,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -657,6 +660,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -674,13 +678,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -725,7 +747,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=y # CONFIG_CONFIGFS_FS is not set # @@ -792,6 +813,8 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set +# CONFIG_UNWIND_INFO is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="ip=any" diff --git a/arch/mips/configs/decstation_defconfig b/arch/mips/configs/decstation_defconfig index 5a181eadd43..d838496e114 100644 --- a/arch/mips/configs/decstation_defconfig +++ b/arch/mips/configs/decstation_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:03 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:01 2006 # CONFIG_MIPS=y @@ -63,11 +63,13 @@ CONFIG_MACH_DECSTATION=y # CONFIG_TOSHIBA_JMR3927 is not set # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set +CONFIG_EARLY_PRINTK=y CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y -CONFIG_EARLY_PRINTK=y # CONFIG_CPU_BIG_ENDIAN is not set CONFIG_CPU_LITTLE_ENDIAN=y CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y @@ -113,7 +115,6 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_WB=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y @@ -135,7 +136,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -151,6 +151,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -165,10 +166,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -180,7 +177,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y # CONFIG_MODVERSIONS is not set CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -189,6 +185,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -233,11 +231,10 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y -CONFIG_XFRM=y -CONFIG_XFRM_USER=m # CONFIG_NET_KEY is not set CONFIG_INET=y # CONFIG_IP_MULTICAST is not set @@ -254,12 +251,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -271,6 +271,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -280,11 +285,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -305,6 +305,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -345,7 +348,7 @@ CONFIG_BLK_DEV_LOOP=m # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set @@ -567,10 +570,6 @@ CONFIG_RTC=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -588,6 +587,7 @@ CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_MACMODES is not set +CONFIG_FB_FIRMWARE_EDID=y # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set # CONFIG_FB_S1D13XXX is not set @@ -617,6 +617,7 @@ CONFIG_LOGO_DEC_CLUT224=y # # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -633,12 +634,30 @@ CONFIG_LOGO_DEC_CLUT224=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -686,7 +705,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -705,7 +723,6 @@ CONFIG_RELAYFS_FS=m # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set CONFIG_UFS_FS=y -CONFIG_UFS_FS_WRITE=y # # Network File Systems diff --git a/arch/mips/configs/e55_defconfig b/arch/mips/configs/e55_defconfig index 8fbfc06a6a2..0760f431891 100644 --- a/arch/mips/configs/e55_defconfig +++ b/arch/mips/configs/e55_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:04 2006 +# Linux kernel version: 2.6.17-rc2 +# Tue Apr 25 00:08:20 2006 # CONFIG_MIPS=y @@ -70,6 +70,8 @@ CONFIG_CASIO_E55=y # CONFIG_VICTOR_MPC30X is not set # CONFIG_ZAO_CAPCELLA is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -88,7 +90,7 @@ CONFIG_MIPS_L1_CACHE_SHIFT=5 # CONFIG_CPU_MIPS64_R2 is not set # CONFIG_CPU_R3000 is not set # CONFIG_CPU_TX39XX is not set -# CONFIG_CPU_VR41XX is not set +CONFIG_CPU_VR41XX=y # CONFIG_CPU_R4300 is not set # CONFIG_CPU_R4X00 is not set # CONFIG_CPU_TX49XX is not set @@ -101,18 +103,21 @@ CONFIG_MIPS_L1_CACHE_SHIFT=5 # CONFIG_CPU_RM7000 is not set # CONFIG_CPU_RM9000 is not set # CONFIG_CPU_SB1 is not set +CONFIG_SYS_HAS_CPU_VR41XX=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_64BIT_KERNEL=y # # Kernel type # -# CONFIG_32BIT is not set +CONFIG_32BIT=y # CONFIG_64BIT is not set CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_8KB is not set # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y @@ -133,7 +138,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -144,11 +148,10 @@ CONFIG_LOCALVERSION="" CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y -# CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set CONFIG_SYSCTL=y -# CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -162,10 +165,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -177,7 +176,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -185,6 +183,9 @@ CONFIG_KMOD=y # # Block layer # +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -219,85 +220,12 @@ CONFIG_MMU=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set +CONFIG_TRAD_SIGNALS=y # # Networking # -CONFIG_NET=y - -# -# Networking options -# -CONFIG_PACKET=y -CONFIG_PACKET_MMAP=y -CONFIG_UNIX=y -CONFIG_XFRM=y -CONFIG_XFRM_USER=m -CONFIG_NET_KEY=y -CONFIG_INET=y -CONFIG_IP_MULTICAST=y -# CONFIG_IP_ADVANCED_ROUTER is not set -CONFIG_IP_FIB_HASH=y -# CONFIG_IP_PNP is not set -# CONFIG_NET_IPIP is not set -# CONFIG_NET_IPGRE is not set -# CONFIG_IP_MROUTE is not set -# CONFIG_ARPD is not set -# CONFIG_SYN_COOKIES is not set -# CONFIG_INET_AH is not set -# CONFIG_INET_ESP is not set -# CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m -CONFIG_INET_DIAG=y -CONFIG_INET_TCP_DIAG=y -# CONFIG_TCP_CONG_ADVANCED is not set -CONFIG_TCP_CONG_BIC=y -# CONFIG_IPV6 is not set -# CONFIG_NETFILTER is not set - -# -# DCCP Configuration (EXPERIMENTAL) -# -# CONFIG_IP_DCCP is not set - -# -# SCTP Configuration (EXPERIMENTAL) -# -# CONFIG_IP_SCTP is not set -# CONFIG_ATM is not set -# CONFIG_BRIDGE is not set -# CONFIG_VLAN_8021Q is not set -# CONFIG_DECNET is not set -# CONFIG_LLC2 is not set -# CONFIG_IPX is not set -# CONFIG_ATALK is not set -# CONFIG_X25 is not set -# CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set -# CONFIG_NET_DIVERT is not set -# CONFIG_ECONET is not set -# CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# -# CONFIG_NET_SCHED is not set - -# -# Network testing -# -# CONFIG_NET_PKTGEN is not set -# CONFIG_HAMRADIO is not set -# CONFIG_IRDA is not set -# CONFIG_BT is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m +# CONFIG_NET is not set # # Device Drivers @@ -313,7 +241,6 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # # Connector - unified userspace <-> kernelspace linker # -CONFIG_CONNECTOR=m # # Memory Technology Devices (MTD) @@ -335,11 +262,11 @@ CONFIG_CONNECTOR=m # # CONFIG_BLK_DEV_COW_COMMON is not set # CONFIG_BLK_DEV_LOOP is not set -# CONFIG_BLK_DEV_NBD is not set -# CONFIG_BLK_DEV_RAM is not set +CONFIG_BLK_DEV_RAM=m CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +# CONFIG_BLK_DEV_INITRD is not set # CONFIG_CDROM_PKTCDVD is not set -# CONFIG_ATA_OVER_ETH is not set # # ATA/ATAPI/MFM/RLL support @@ -398,81 +325,8 @@ CONFIG_IDE_GENERIC=y # # -# Network device support -# -CONFIG_NETDEVICES=y -# CONFIG_DUMMY is not set -# CONFIG_BONDING is not set -# CONFIG_EQUALIZER is not set -# CONFIG_TUN is not set - -# -# ARCnet devices -# -# CONFIG_ARCNET is not set - -# -# PHY device support -# -CONFIG_PHYLIB=m - -# -# MII PHY device drivers -# -CONFIG_MARVELL_PHY=m -CONFIG_DAVICOM_PHY=m -CONFIG_QSEMI_PHY=m -CONFIG_LXT_PHY=m -CONFIG_CICADA_PHY=m - -# -# Ethernet (10 or 100Mbit) -# -CONFIG_NET_ETHERNET=y -# CONFIG_MII is not set -# CONFIG_NET_VENDOR_3COM is not set -# CONFIG_NET_VENDOR_SMC is not set -# CONFIG_DM9000 is not set -# CONFIG_NET_VENDOR_RACAL is not set -# CONFIG_AT1700 is not set -# CONFIG_DEPCA is not set -# CONFIG_HP100 is not set -# CONFIG_NET_ISA is not set -# CONFIG_NET_PCI is not set - -# -# Ethernet (1000 Mbit) -# - -# -# Ethernet (10000 Mbit) -# - -# -# Token Ring devices -# -# CONFIG_TR is not set - -# -# Wireless LAN (non-hamradio) -# -# CONFIG_NET_RADIO is not set - -# -# Wan interfaces -# -# CONFIG_WAN is not set -# CONFIG_PPP is not set -# CONFIG_SLIP is not set -# CONFIG_SHAPER is not set -# CONFIG_NETCONSOLE is not set -# CONFIG_NETPOLL is not set -# CONFIG_NET_POLL_CONTROLLER is not set - -# # ISDN subsystem # -# CONFIG_ISDN is not set # # Telephony Support @@ -508,11 +362,7 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=240 # # Hardware I/O ports # -CONFIG_SERIO=y -# CONFIG_SERIO_I8042 is not set -CONFIG_SERIO_SERPORT=y -# CONFIG_SERIO_LIBPS2 is not set -CONFIG_SERIO_RAW=m +# CONFIG_SERIO is not set # CONFIG_GAMEPORT is not set # @@ -531,6 +381,10 @@ CONFIG_HW_CONSOLE=y # # Non-8250 serial port support # +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_SERIAL_VR41XX=y +CONFIG_SERIAL_VR41XX_CONSOLE=y CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -565,6 +419,7 @@ CONFIG_WATCHDOG=y # # Ftape, the floppy tape device driver # +CONFIG_GPIO_VR41XX=y # CONFIG_RAW_DRIVER is not set # @@ -600,10 +455,6 @@ CONFIG_WATCHDOG=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -611,7 +462,6 @@ CONFIG_WATCHDOG=y # # Digital Video Broadcasting Devices # -# CONFIG_DVB is not set # # Graphics support @@ -635,6 +485,7 @@ CONFIG_DUMMY_CONSOLE=y # # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -651,12 +502,30 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -669,13 +538,12 @@ CONFIG_EXT2_FS=y # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set # CONFIG_XFS_FS is not set -# CONFIG_OCFS2_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_ROMFS_FS is not set CONFIG_INOTIFY=y # CONFIG_QUOTA is not set CONFIG_DNOTIFY=y -CONFIG_AUTOFS_FS=y +# CONFIG_AUTOFS_FS is not set CONFIG_AUTOFS4_FS=y CONFIG_FUSE_FS=m @@ -698,10 +566,9 @@ CONFIG_FUSE_FS=m CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_SYSFS=y -# CONFIG_TMPFS is not set +CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -722,29 +589,6 @@ CONFIG_RELAYFS_FS=m # CONFIG_UFS_FS is not set # -# Network File Systems -# -CONFIG_NFS_FS=m -# CONFIG_NFS_V3 is not set -# CONFIG_NFS_V4 is not set -# CONFIG_NFS_DIRECTIO is not set -CONFIG_NFSD=m -# CONFIG_NFSD_V3 is not set -# CONFIG_NFSD_TCP is not set -CONFIG_LOCKD=m -CONFIG_EXPORTFS=m -CONFIG_NFS_COMMON=y -CONFIG_SUNRPC=m -# CONFIG_RPCSEC_GSS_KRB5 is not set -# CONFIG_RPCSEC_GSS_SPKM3 is not set -# CONFIG_SMB_FS is not set -# CONFIG_CIFS is not set -# CONFIG_NCP_FS is not set -# CONFIG_CODA_FS is not set -# CONFIG_AFS_FS is not set -# CONFIG_9P_FS is not set - -# # Partition Types # # CONFIG_PARTITION_ADVANCED is not set @@ -767,44 +611,20 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="console=ttyVR0,19200 mem=8M" # # Security options # -CONFIG_KEYS=y -CONFIG_KEYS_DEBUG_PROC_KEYS=y +# CONFIG_KEYS is not set # CONFIG_SECURITY is not set # # Cryptographic options # -CONFIG_CRYPTO=y -CONFIG_CRYPTO_HMAC=y -CONFIG_CRYPTO_NULL=m -CONFIG_CRYPTO_MD4=m -CONFIG_CRYPTO_MD5=m -CONFIG_CRYPTO_SHA1=m -CONFIG_CRYPTO_SHA256=m -CONFIG_CRYPTO_SHA512=m -CONFIG_CRYPTO_WP512=m -CONFIG_CRYPTO_TGR192=m -CONFIG_CRYPTO_DES=m -CONFIG_CRYPTO_BLOWFISH=m -CONFIG_CRYPTO_TWOFISH=m -CONFIG_CRYPTO_SERPENT=m -CONFIG_CRYPTO_AES=m -CONFIG_CRYPTO_CAST5=m -CONFIG_CRYPTO_CAST6=m -CONFIG_CRYPTO_TEA=m -CONFIG_CRYPTO_ARC4=m -CONFIG_CRYPTO_KHAZAD=m -CONFIG_CRYPTO_ANUBIS=m -CONFIG_CRYPTO_DEFLATE=m -CONFIG_CRYPTO_MICHAEL_MIC=m -CONFIG_CRYPTO_CRC32C=m -# CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO is not set # # Hardware crypto devices @@ -814,8 +634,6 @@ CONFIG_CRYPTO_CRC32C=m # Library routines # # CONFIG_CRC_CCITT is not set -CONFIG_CRC16=m -CONFIG_CRC32=m -CONFIG_LIBCRC32C=m -CONFIG_ZLIB_INFLATE=m -CONFIG_ZLIB_DEFLATE=m +# CONFIG_CRC16 is not set +# CONFIG_CRC32 is not set +# CONFIG_LIBCRC32C is not set diff --git a/arch/mips/configs/ev64120_defconfig b/arch/mips/configs/ev64120_defconfig index f2d43be6900..7067f608b22 100644 --- a/arch/mips/configs/ev64120_defconfig +++ b/arch/mips/configs/ev64120_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:05 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:02 2006 # CONFIG_MIPS=y @@ -65,6 +65,8 @@ CONFIG_MIPS_EV64120=y # CONFIG_TOSHIBA_RBTX4938 is not set # CONFIG_EVB_PCI1 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -116,7 +118,6 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -138,7 +139,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -154,6 +154,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -167,10 +168,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -182,7 +179,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y # CONFIG_KMOD is not set @@ -191,6 +187,8 @@ CONFIG_MODULE_SRCVERSION_ALL=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -210,7 +208,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -238,6 +235,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set # CONFIG_PACKET is not set CONFIG_UNIX=y CONFIG_XFRM=y @@ -258,12 +256,15 @@ CONFIG_IP_PNP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -275,6 +276,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -284,11 +290,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -309,6 +310,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -352,7 +356,7 @@ CONFIG_CONNECTOR=m # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -550,6 +554,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -559,6 +564,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -617,10 +623,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -651,6 +653,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -668,13 +671,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -719,7 +740,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -783,6 +803,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="console=ttyS0,115200 root=/dev/nfs rw nfsroot=192.168.1.1:/mnt/disk2/fs.gal ip=192.168.1.211:192.168.1.1:::gt::" diff --git a/arch/mips/configs/ev96100_defconfig b/arch/mips/configs/ev96100_defconfig index ac5841c4b69..00b56ed0e63 100644 --- a/arch/mips/configs/ev96100_defconfig +++ b/arch/mips/configs/ev96100_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:06 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:03 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_EV96100=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -119,7 +121,6 @@ CONFIG_RM7000_CPU_SCACHE=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -142,7 +143,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -158,6 +158,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -171,10 +172,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -186,7 +183,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y # CONFIG_KMOD is not set @@ -195,6 +191,8 @@ CONFIG_MODULE_SRCVERSION_ALL=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -240,6 +238,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set # CONFIG_PACKET is not set CONFIG_UNIX=y CONFIG_XFRM=y @@ -260,12 +259,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -277,6 +279,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -286,11 +293,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -311,6 +313,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -349,7 +354,7 @@ CONFIG_CONNECTOR=m # CONFIG_BLK_DEV_LOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -567,10 +572,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -601,6 +602,7 @@ CONFIG_DUMMY_CONSOLE=y # # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -617,12 +619,30 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -667,7 +687,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -731,6 +750,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/ip22_defconfig b/arch/mips/configs/ip22_defconfig index 42d5cd7927c..607e2985ffe 100644 --- a/arch/mips/configs/ip22_defconfig +++ b/arch/mips/configs/ip22_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:39:51 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:50:54 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_SGI_IP22=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_ARC=y CONFIG_DMA_NONCOHERENT=y @@ -121,7 +123,6 @@ CONFIG_BOARD_SCACHE=y CONFIG_IP22_CPU_SCACHE=y # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -143,7 +144,6 @@ CONFIG_PREEMPT_VOLUNTARY=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -160,6 +160,7 @@ CONFIG_SYSCTL=y # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -173,10 +174,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -188,7 +185,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -197,6 +193,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -242,6 +240,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -264,6 +263,7 @@ CONFIG_IP_PNP_BOOTP=y CONFIG_INET_AH=m CONFIG_INET_ESP=m CONFIG_INET_IPCOMP=m +CONFIG_INET_XFRM_TUNNEL=m CONFIG_INET_TUNNEL=m CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y @@ -305,9 +305,12 @@ CONFIG_IP_VS_NQ=m CONFIG_IP_VS_FTP=m CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y +CONFIG_IPV6_ROUTER_PREF=y +CONFIG_IPV6_ROUTE_INFO=y CONFIG_INET6_AH=m CONFIG_INET6_ESP=m CONFIG_INET6_IPCOMP=m +CONFIG_INET6_XFRM_TUNNEL=m CONFIG_INET6_TUNNEL=m CONFIG_IPV6_TUNNEL=m CONFIG_NETFILTER=y @@ -330,11 +333,14 @@ CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m CONFIG_NETFILTER_XT_MATCH_CONNMARK=m CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m @@ -357,20 +363,19 @@ CONFIG_IP_NF_IRC=m CONFIG_IP_NF_TFTP=m CONFIG_IP_NF_AMANDA=m CONFIG_IP_NF_PPTP=m +CONFIG_IP_NF_H323=m CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_IPRANGE=m -CONFIG_IP_NF_MATCH_MULTIPORT=m CONFIG_IP_NF_MATCH_TOS=m CONFIG_IP_NF_MATCH_RECENT=m CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_DSCP=m -CONFIG_IP_NF_MATCH_AH_ESP=m +CONFIG_IP_NF_MATCH_AH=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_MATCH_OWNER=m CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_HASHLIMIT=m -CONFIG_IP_NF_MATCH_POLICY=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -388,6 +393,7 @@ CONFIG_IP_NF_NAT_FTP=m CONFIG_IP_NF_NAT_TFTP=m CONFIG_IP_NF_NAT_AMANDA=m CONFIG_IP_NF_NAT_PPTP=m +CONFIG_IP_NF_NAT_H323=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_TOS=m CONFIG_IP_NF_TARGET_ECN=m @@ -408,12 +414,10 @@ CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_FRAG=m CONFIG_IP6_NF_MATCH_HL=m -CONFIG_IP6_NF_MATCH_MULTIPORT=m CONFIG_IP6_NF_MATCH_OWNER=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AHESP=m +CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_MATCH_POLICY=m CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_LOG=m CONFIG_IP6_NF_TARGET_REJECT=m @@ -435,6 +439,11 @@ CONFIG_IP_SCTP=m # CONFIG_SCTP_HMAC_NONE is not set # CONFIG_SCTP_HMAC_SHA1 is not set CONFIG_SCTP_HMAC_MD5=y + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -444,11 +453,6 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set CONFIG_NET_DIVERT=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -508,6 +512,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -546,7 +553,7 @@ CONFIG_CONNECTOR=m # CONFIG_BLK_DEV_LOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -812,10 +819,6 @@ CONFIG_MAX_RAW_DEVS=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -857,6 +860,7 @@ CONFIG_LOGO_SGI_CLUT224=y # # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -873,12 +877,30 @@ CONFIG_LOGO_SGI_CLUT224=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -944,7 +966,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -963,7 +984,6 @@ CONFIG_EFS_FS=m # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set CONFIG_UFS_FS=m -# CONFIG_UFS_FS_WRITE is not set # # Network File Systems @@ -1078,6 +1098,7 @@ CONFIG_NLS_UTF8=m # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/ip27_defconfig b/arch/mips/configs/ip27_defconfig index 8c40590737e..f724b4b2ecf 100644 --- a/arch/mips/configs/ip27_defconfig +++ b/arch/mips/configs/ip27_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc4 -# Tue Feb 21 13:44:31 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:04 2006 # CONFIG_MIPS=y @@ -70,6 +70,8 @@ CONFIG_NUMA=y # CONFIG_REPLICATE_KTEXT is not set # CONFIG_REPLICATE_EXHANDLERS is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_ARC=y CONFIG_DMA_IP27=y @@ -123,6 +125,7 @@ CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_CPU_SUPPORTS_HIGHMEM=y +CONFIG_NODES_SHIFT=6 CONFIG_SELECT_MEMORY_MODEL=y # CONFIG_FLATMEM_MANUAL is not set CONFIG_DISCONTIGMEM_MANUAL=y @@ -162,6 +165,7 @@ CONFIG_SYSCTL=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_CPUSETS=y +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -175,10 +179,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -190,7 +190,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y # CONFIG_MODVERSIONS is not set CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -199,6 +198,7 @@ CONFIG_STOP_MACHINE=y # # Block layer # +# CONFIG_BLK_DEV_IO_TRACE is not set # # IO Schedulers @@ -219,7 +219,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_HW_HAS_PCI=y CONFIG_PCI=y CONFIG_PCI_DOMAINS=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -237,6 +236,7 @@ CONFIG_MMU=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set +# CONFIG_BUILD_ELF64 is not set CONFIG_MIPS32_COMPAT=y CONFIG_COMPAT=y CONFIG_MIPS32_O32=y @@ -274,12 +274,15 @@ CONFIG_IP_PNP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -363,6 +366,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -407,7 +413,7 @@ CONFIG_BLK_DEV_CRYPTOLOOP=m # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -473,7 +479,6 @@ CONFIG_SCSI_SAS_ATTRS=m # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set -# CONFIG_SCSI_QLOGIC_FC is not set CONFIG_SCSI_QLOGIC_1280=y # CONFIG_SCSI_QLA_FC is not set # CONFIG_SCSI_LPFC is not set @@ -491,6 +496,7 @@ CONFIG_MD_RAID0=y CONFIG_MD_RAID1=y CONFIG_MD_RAID10=m CONFIG_MD_RAID5=y +CONFIG_MD_RAID5_RESHAPE=y CONFIG_MD_RAID6=m CONFIG_MD_MULTIPATH=m CONFIG_MD_FAULTY=m @@ -654,6 +660,7 @@ CONFIG_SERIO_RAW=m # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 CONFIG_SERIAL_8250_EXTENDED=y @@ -727,10 +734,6 @@ CONFIG_SGI_IP27_RTC=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -755,6 +758,7 @@ CONFIG_SGI_IP27_RTC=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -772,17 +776,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) # # -# EDAC - error detection and reporting (RAS) +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -840,7 +858,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -922,6 +939,7 @@ CONFIG_SGI_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=15 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/ip32_defconfig b/arch/mips/configs/ip32_defconfig index 7fdcaf51fac..8f11d3565b2 100644 --- a/arch/mips/configs/ip32_defconfig +++ b/arch/mips/configs/ip32_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:09 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:05 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_SGI_IP32=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_ARC=y CONFIG_DMA_IP32=y @@ -142,7 +144,6 @@ CONFIG_PREEMPT_VOLUNTARY=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -159,6 +160,7 @@ CONFIG_BSD_PROCESS_ACCT=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -172,10 +174,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -189,6 +187,7 @@ CONFIG_BASE_SMALL=0 # # Block layer # +# CONFIG_BLK_DEV_IO_TRACE is not set # # IO Schedulers @@ -208,7 +207,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -226,6 +224,7 @@ CONFIG_MMU=y # CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y +# CONFIG_BUILD_ELF64 is not set CONFIG_MIPS32_COMPAT=y CONFIG_COMPAT=y CONFIG_MIPS32_O32=y @@ -240,6 +239,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -261,12 +261,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=y +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -278,6 +281,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -287,11 +295,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -312,6 +315,9 @@ CONFIG_IEEE80211=y # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=y CONFIG_IEEE80211_CRYPT_CCMP=y +CONFIG_IEEE80211_SOFTMAC=y +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -357,7 +363,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=y CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -428,7 +434,6 @@ CONFIG_AIC7XXX_REG_PRETTY_PRINT=y # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set -# CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_QLOGIC_1280 is not set # CONFIG_SCSI_QLA_FC is not set # CONFIG_SCSI_LPFC is not set @@ -615,6 +620,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -624,6 +630,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -682,10 +689,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -716,6 +719,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -733,13 +737,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -784,7 +806,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=y # CONFIG_CONFIGFS_FS is not set # @@ -861,6 +882,8 @@ CONFIG_SGI_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set +# CONFIG_UNWIND_INFO is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/it8172_defconfig b/arch/mips/configs/it8172_defconfig index c716996d9ec..757adf23853 100644 --- a/arch/mips/configs/it8172_defconfig +++ b/arch/mips/configs/it8172_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:10 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:05 2006 # CONFIG_MIPS=y @@ -65,6 +65,8 @@ CONFIG_MIPS_ITE8172=y # CONFIG_TOSHIBA_RBTX4938 is not set # CONFIG_IT8172_REVC is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -115,7 +117,6 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -137,7 +138,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -154,6 +154,7 @@ CONFIG_BSD_PROCESS_ACCT=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -167,10 +168,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -183,7 +180,6 @@ CONFIG_OBSOLETE_INTERMODULE=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -192,6 +188,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -237,6 +235,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -258,12 +257,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -275,6 +277,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -284,11 +291,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -309,6 +311,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -387,7 +392,6 @@ CONFIG_MTD_PHYSMAP_BANKWIDTH=2 # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLKMTD is not set # CONFIG_MTD_BLOCK2MTD is not set # @@ -424,7 +428,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -666,10 +670,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -704,7 +704,6 @@ CONFIG_SOUND=y # Open Sound System # CONFIG_SOUND_PRIME=y -# CONFIG_OBSOLETE_OSS_DRIVER is not set CONFIG_SOUND_IT8172=y # CONFIG_SOUND_MSNDCLAS is not set # CONFIG_SOUND_MSNDPIN is not set @@ -714,6 +713,7 @@ CONFIG_SOUND_IT8172=y # # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -730,12 +730,30 @@ CONFIG_SOUND_IT8172=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -780,7 +798,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -846,6 +863,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/ivr_defconfig b/arch/mips/configs/ivr_defconfig index a8376d125e1..021761a8a23 100644 --- a/arch/mips/configs/ivr_defconfig +++ b/arch/mips/configs/ivr_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:11 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:06 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_IVR=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -112,7 +114,6 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -134,7 +135,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -151,6 +151,7 @@ CONFIG_BSD_PROCESS_ACCT=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -164,10 +165,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -179,7 +176,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -188,6 +184,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -207,7 +205,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -235,6 +232,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -256,12 +254,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -273,6 +274,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -282,11 +288,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -307,6 +308,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -350,7 +354,7 @@ CONFIG_CONNECTOR=m # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -565,6 +569,7 @@ CONFIG_IT8172_SCR1=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -574,6 +579,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -631,10 +637,6 @@ CONFIG_RTC=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -665,6 +667,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -682,13 +685,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -733,7 +754,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -797,6 +817,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/jaguar-atx_defconfig b/arch/mips/configs/jaguar-atx_defconfig index 316015379db..08f6c30b0ab 100644 --- a/arch/mips/configs/jaguar-atx_defconfig +++ b/arch/mips/configs/jaguar-atx_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:12 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:06 2006 # CONFIG_MIPS=y @@ -65,6 +65,8 @@ CONFIG_MOMENCO_JAGUAR_ATX=y # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_JAGUAR_DMALOW=y CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -122,7 +124,6 @@ CONFIG_RM7000_CPU_SCACHE=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -144,7 +145,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # # CONFIG_EXPERIMENTAL is not set -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -160,6 +160,7 @@ CONFIG_SYSCTL=y # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" CONFIG_EMBEDDED=y CONFIG_KALLSYMS=y @@ -172,10 +173,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -186,7 +183,6 @@ CONFIG_BASE_SMALL=0 # CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y -CONFIG_OBSOLETE_MODPARM=y # CONFIG_MODVERSIONS is not set CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -195,6 +191,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -214,7 +212,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -241,6 +238,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set # CONFIG_PACKET is not set CONFIG_UNIX=y CONFIG_XFRM=y @@ -260,16 +258,19 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y +CONFIG_IPV6_ROUTER_PREF=y CONFIG_INET6_AH=m CONFIG_INET6_ESP=m CONFIG_INET6_IPCOMP=m +CONFIG_INET6_XFRM_TUNNEL=m CONFIG_INET6_TUNNEL=m CONFIG_IPV6_TUNNEL=m # CONFIG_NETFILTER is not set @@ -338,10 +339,9 @@ CONFIG_CONNECTOR=m # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 -# CONFIG_CDROM_PKTCDVD_WCACHE is not set CONFIG_ATA_OVER_ETH=m # @@ -423,6 +423,7 @@ CONFIG_NET_PCI=y # CONFIG_PCNET32 is not set # CONFIG_AMD8111_ETH is not set # CONFIG_ADAPTEC_STARFIRE is not set +# CONFIG_FORCEDETH is not set # CONFIG_DGRS is not set CONFIG_EEPRO100=y # CONFIG_E100 is not set @@ -446,6 +447,7 @@ CONFIG_EEPRO100=y # CONFIG_HAMACHI is not set # CONFIG_R8169 is not set # CONFIG_SIS190 is not set +# CONFIG_SKGE is not set # CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set @@ -514,6 +516,7 @@ CONFIG_MV643XX_ETH_2=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -523,6 +526,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -579,10 +583,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -607,6 +607,7 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -624,12 +625,29 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # # @@ -672,7 +690,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # # Miscellaneous filesystems @@ -718,6 +735,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/jmr3927_defconfig b/arch/mips/configs/jmr3927_defconfig index 53fbef1ac25..38b1e026e10 100644 --- a/arch/mips/configs/jmr3927_defconfig +++ b/arch/mips/configs/jmr3927_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:13 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:07 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_TOSHIBA_JMR3927=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -111,7 +113,6 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y @@ -133,7 +134,6 @@ CONFIG_RTC_DS1742=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -149,6 +149,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -162,10 +163,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -180,6 +177,8 @@ CONFIG_BASE_SMALL=0 # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -199,7 +198,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -227,6 +225,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -248,12 +247,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=y +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -265,6 +267,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -274,11 +281,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -299,6 +301,9 @@ CONFIG_IEEE80211=y # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=y CONFIG_IEEE80211_CRYPT_CCMP=y +CONFIG_IEEE80211_SOFTMAC=y +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -343,7 +348,7 @@ CONFIG_PROC_EVENTS=y # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=y CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -551,7 +556,12 @@ CONFIG_SERIAL_NONSTANDARD=y # # Non-8250 serial port support # +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_TXX9=y CONFIG_HAS_TXX9_SERIAL=y +# CONFIG_SERIAL_TXX9_CONSOLE is not set +# CONFIG_SERIAL_TXX9_STDSERIAL is not set +# CONFIG_SERIAL_JSM is not set # CONFIG_UNIX98_PTYS is not set CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -610,10 +620,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -631,6 +637,7 @@ CONFIG_FB=y # CONFIG_FB_CFB_COPYAREA is not set # CONFIG_FB_CFB_IMAGEBLIT is not set # CONFIG_FB_MACMODES is not set +CONFIG_FB_FIRMWARE_EDID=y # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set # CONFIG_FB_CIRRUS is not set @@ -642,7 +649,6 @@ CONFIG_FB=y # CONFIG_FB_NVIDIA is not set # CONFIG_FB_RIVA is not set # CONFIG_FB_MATROX is not set -# CONFIG_FB_RADEON_OLD is not set # CONFIG_FB_RADEON is not set # CONFIG_FB_ATY128 is not set # CONFIG_FB_ATY is not set @@ -679,6 +685,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -696,13 +703,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -745,7 +770,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=y # CONFIG_CONFIGFS_FS is not set # @@ -809,6 +833,8 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set +# CONFIG_UNWIND_INFO is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/lasat200_defconfig b/arch/mips/configs/lasat200_defconfig index ef0fa9fc79d..4d25990a0a0 100644 --- a/arch/mips/configs/lasat200_defconfig +++ b/arch/mips/configs/lasat200_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:14 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:07 2006 # CONFIG_MIPS=y @@ -68,6 +68,8 @@ CONFIG_PICVUE_PROC=y CONFIG_DS1603=y CONFIG_LASAT_SYSCTL=y CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -119,7 +121,6 @@ CONFIG_BOARD_SCACHE=y CONFIG_R5000_CPU_SCACHE=y # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -141,7 +142,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -157,6 +157,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -170,10 +171,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -186,7 +183,6 @@ CONFIG_OBSOLETE_INTERMODULE=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -195,6 +191,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -214,7 +212,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -242,6 +239,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set # CONFIG_PACKET is not set CONFIG_UNIX=y CONFIG_XFRM=y @@ -259,12 +257,15 @@ CONFIG_IP_FIB_HASH=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -276,6 +277,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -285,11 +291,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -310,6 +311,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -366,7 +370,6 @@ CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_CFI_INTELEXT is not set CONFIG_MTD_CFI_AMDSTD=y -CONFIG_MTD_CFI_AMDSTD_RETRY=0 # CONFIG_MTD_CFI_STAA is not set CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set @@ -389,7 +392,6 @@ CONFIG_MTD_LASAT=y # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLKMTD is not set # CONFIG_MTD_BLOCK2MTD is not set # @@ -430,7 +432,7 @@ CONFIG_MTD_LASAT=y # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -672,6 +674,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -681,6 +684,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -739,10 +743,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -773,6 +773,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -790,13 +791,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -847,7 +866,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -914,6 +932,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/malta_defconfig b/arch/mips/configs/malta_defconfig index 367d279efdd..977f52be51d 100644 --- a/arch/mips/configs/malta_defconfig +++ b/arch/mips/configs/malta_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:15 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:08 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_MALTA=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_ARCH_MAY_HAVE_PC_FDC=y CONFIG_DMA_NONCOHERENT=y @@ -128,16 +130,21 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_64KB is not set CONFIG_CPU_HAS_PREFETCH=y CONFIG_MIPS_MT=y +# CONFIG_MIPS_MT_SMTC is not set # CONFIG_MIPS_MT_SMP is not set CONFIG_MIPS_VPE_LOADER=y +CONFIG_MIPS_MT_FPAFF=y CONFIG_MIPS_VPE_LOADER_TOM=y CONFIG_MIPS_VPE_APSP_API=y +CONFIG_MIPS_APSP_KSPD=y # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y +# CONFIG_CPU_MIPSR2_IRQ_VI is not set +# CONFIG_CPU_MIPSR2_IRQ_EI is not set CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -155,7 +162,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -171,6 +177,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -184,10 +191,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -199,7 +202,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -208,6 +210,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -227,7 +231,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -255,6 +258,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -287,6 +291,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_AH=m CONFIG_INET_ESP=m CONFIG_INET_IPCOMP=m +CONFIG_INET_XFRM_TUNNEL=m CONFIG_INET_TUNNEL=m CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y @@ -328,9 +333,12 @@ CONFIG_IP_VS_NQ=m CONFIG_IP_VS_FTP=m CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y +CONFIG_IPV6_ROUTER_PREF=y +CONFIG_IPV6_ROUTE_INFO=y CONFIG_INET6_AH=m CONFIG_INET6_ESP=m CONFIG_INET6_IPCOMP=m +CONFIG_INET6_XFRM_TUNNEL=m CONFIG_INET6_TUNNEL=m CONFIG_IPV6_TUNNEL=m CONFIG_NETFILTER=y @@ -354,11 +362,14 @@ CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m CONFIG_NETFILTER_XT_MATCH_CONNMARK=m CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m # CONFIG_NETFILTER_XT_MATCH_PHYSDEV is not set CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m @@ -382,20 +393,19 @@ CONFIG_IP_NF_IRC=m CONFIG_IP_NF_TFTP=m CONFIG_IP_NF_AMANDA=m CONFIG_IP_NF_PPTP=m +CONFIG_IP_NF_H323=m CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_IPRANGE=m -CONFIG_IP_NF_MATCH_MULTIPORT=m CONFIG_IP_NF_MATCH_TOS=m CONFIG_IP_NF_MATCH_RECENT=m CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_DSCP=m -CONFIG_IP_NF_MATCH_AH_ESP=m +CONFIG_IP_NF_MATCH_AH=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_MATCH_OWNER=m CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_HASHLIMIT=m -CONFIG_IP_NF_MATCH_POLICY=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -413,6 +423,7 @@ CONFIG_IP_NF_NAT_FTP=m CONFIG_IP_NF_NAT_TFTP=m CONFIG_IP_NF_NAT_AMANDA=m CONFIG_IP_NF_NAT_PPTP=m +CONFIG_IP_NF_NAT_H323=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_TOS=m CONFIG_IP_NF_TARGET_ECN=m @@ -433,12 +444,10 @@ CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_FRAG=m CONFIG_IP6_NF_MATCH_HL=m -CONFIG_IP6_NF_MATCH_MULTIPORT=m CONFIG_IP6_NF_MATCH_OWNER=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AHESP=m +CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_MATCH_POLICY=m CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_LOG=m CONFIG_IP6_NF_TARGET_REJECT=m @@ -484,6 +493,11 @@ CONFIG_IP_SCTP=m # CONFIG_SCTP_HMAC_NONE is not set # CONFIG_SCTP_HMAC_SHA1 is not set CONFIG_SCTP_HMAC_MD5=y + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set CONFIG_BRIDGE=m CONFIG_VLAN_8021Q=m @@ -498,11 +512,6 @@ CONFIG_IPDDP_ENCAP=y CONFIG_IPDDP_DECAP=y # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set CONFIG_NET_DIVERT=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -562,6 +571,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -734,7 +746,6 @@ CONFIG_AIC7XXX_REG_PRETTY_PRINT=y # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set -# CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_QLOGIC_1280 is not set # CONFIG_SCSI_QLA_FC is not set # CONFIG_SCSI_LPFC is not set @@ -753,6 +764,7 @@ CONFIG_MD_RAID0=m CONFIG_MD_RAID1=m CONFIG_MD_RAID10=m CONFIG_MD_RAID5=m +CONFIG_MD_RAID5_RESHAPE=y CONFIG_MD_RAID6=m CONFIG_MD_MULTIPATH=m CONFIG_MD_FAULTY=m @@ -956,6 +968,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -965,6 +978,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -1022,10 +1036,6 @@ CONFIG_RTC=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -1056,6 +1066,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -1073,13 +1084,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -1154,7 +1183,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -1174,7 +1202,6 @@ CONFIG_VXFS_FS=m # CONFIG_QNX4FS_FS is not set CONFIG_SYSV_FS=m CONFIG_UFS_FS=m -# CONFIG_UFS_FS_WRITE is not set # # Network File Systems @@ -1266,6 +1293,7 @@ CONFIG_NLS_UTF8=m # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/mipssim_defconfig b/arch/mips/configs/mipssim_defconfig index fe78961762b..00560e0143f 100644 --- a/arch/mips/configs/mipssim_defconfig +++ b/arch/mips/configs/mipssim_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:16 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:09 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_SIM=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -114,16 +116,19 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_64KB is not set CONFIG_CPU_HAS_PREFETCH=y CONFIG_MIPS_MT=y +# CONFIG_MIPS_MT_SMTC is not set # CONFIG_MIPS_MT_SMP is not set CONFIG_MIPS_VPE_LOADER=y +CONFIG_MIPS_MT_FPAFF=y CONFIG_MIPS_VPE_LOADER_TOM=y CONFIG_MIPS_VPE_APSP_API=y +CONFIG_MIPS_APSP_KSPD=y # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -141,7 +146,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -157,6 +161,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -171,10 +176,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -186,7 +187,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -195,6 +195,7 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -238,6 +239,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -268,12 +270,15 @@ CONFIG_SYN_COOKIES=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -290,6 +295,11 @@ CONFIG_IP_SCTP=m # CONFIG_SCTP_HMAC_NONE is not set # CONFIG_SCTP_HMAC_SHA1 is not set CONFIG_SCTP_HMAC_MD5=y + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -299,11 +309,6 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set CONFIG_NET_DIVERT=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -397,7 +402,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set CONFIG_BLK_DEV_NBD=y # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set @@ -532,7 +537,7 @@ CONFIG_SERIO_SERPORT=y CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_NR_UARTS=1 -CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=1 # CONFIG_SERIAL_8250_EXTENDED is not set # @@ -596,10 +601,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -624,6 +625,7 @@ CONFIG_LEGACY_PTY_COUNT=256 # # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -640,12 +642,30 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -690,8 +710,6 @@ CONFIG_PROC_FS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -# CONFIG_RELAYFS_FS is not set -# CONFIG_CONFIGFS_FS is not set # # Miscellaneous filesystems diff --git a/arch/mips/configs/mpc30x_defconfig b/arch/mips/configs/mpc30x_defconfig index e4620e7f0a5..286a018375b 100644 --- a/arch/mips/configs/mpc30x_defconfig +++ b/arch/mips/configs/mpc30x_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:17 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:09 2006 # CONFIG_MIPS=y @@ -72,6 +72,8 @@ CONFIG_VICTOR_MPC30X=y CONFIG_PCI_VR41XX=y CONFIG_VRC4173=y CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -90,7 +92,7 @@ CONFIG_MIPS_L1_CACHE_SHIFT=5 # CONFIG_CPU_MIPS64_R2 is not set # CONFIG_CPU_R3000 is not set # CONFIG_CPU_TX39XX is not set -# CONFIG_CPU_VR41XX is not set +CONFIG_CPU_VR41XX=y # CONFIG_CPU_R4300 is not set # CONFIG_CPU_R4X00 is not set # CONFIG_CPU_TX49XX is not set @@ -103,18 +105,21 @@ CONFIG_MIPS_L1_CACHE_SHIFT=5 # CONFIG_CPU_RM7000 is not set # CONFIG_CPU_RM9000 is not set # CONFIG_CPU_SB1 is not set +CONFIG_SYS_HAS_CPU_VR41XX=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_64BIT_KERNEL=y # # Kernel type # -# CONFIG_32BIT is not set +CONFIG_32BIT=y # CONFIG_64BIT is not set CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_8KB is not set # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y @@ -135,7 +140,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -151,6 +155,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -164,10 +169,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -179,7 +180,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -187,6 +187,9 @@ CONFIG_KMOD=y # # Block layer # +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -206,7 +209,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -225,6 +227,7 @@ CONFIG_PCMCIA_IOCTL=y # CONFIG_YENTA is not set # CONFIG_PD6729 is not set # CONFIG_I82092 is not set +# CONFIG_PCMCIA_VRC4173 is not set # # PCI Hotplug Support @@ -236,6 +239,7 @@ CONFIG_PCMCIA_IOCTL=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set +CONFIG_TRAD_SIGNALS=y # # Networking @@ -245,6 +249,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -264,12 +269,15 @@ CONFIG_IP_FIB_HASH=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -281,6 +289,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -290,11 +303,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -316,6 +324,9 @@ CONFIG_IEEE80211=m CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m CONFIG_IEEE80211_CRYPT_TKIP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -360,7 +371,7 @@ CONFIG_CONNECTOR=m # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_UB is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set # CONFIG_CDROM_PKTCDVD is not set CONFIG_ATA_OVER_ETH=m @@ -475,6 +486,7 @@ CONFIG_MII=m # Wireless LAN (non-hamradio) # CONFIG_NET_RADIO=y +# CONFIG_NET_WIRELESS_RTNETLINK is not set # # Obsolete Wireless cards support (pre-802.11) @@ -513,6 +525,7 @@ CONFIG_PCMCIA_HERMES=m # # CONFIG_PRISM54 is not set # CONFIG_HOSTAP is not set +# CONFIG_BCM43XX is not set CONFIG_NET_WIRELESS=y # @@ -604,6 +617,8 @@ CONFIG_HW_CONSOLE=y # # Non-8250 serial port support # +# CONFIG_SERIAL_VR41XX is not set +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -634,6 +649,7 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_SYNCLINK_CS is not set # CONFIG_CARDMAN_4000 is not set # CONFIG_CARDMAN_4040 is not set +# CONFIG_GPIO_VR41XX is not set # CONFIG_RAW_DRIVER is not set # @@ -669,10 +685,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -681,6 +693,7 @@ CONFIG_LEGACY_PTY_COUNT=256 # Digital Video Broadcasting Devices # # CONFIG_DVB is not set +# CONFIG_USB_DABUSB is not set # # Graphics support @@ -703,6 +716,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=m # CONFIG_USB_DEBUG is not set @@ -756,9 +770,7 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y # CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set -# CONFIG_USB_MTOUCH is not set -# CONFIG_USB_ITMTOUCH is not set -# CONFIG_USB_EGALAX is not set +# CONFIG_USB_TOUCHSCREEN is not set # CONFIG_USB_YEALINK is not set # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set @@ -772,15 +784,6 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y # CONFIG_USB_MDC800 is not set # -# USB Multimedia devices -# -# CONFIG_USB_DABUSB is not set - -# -# Video4Linux support is needed for USB Multimedia device support -# - -# # USB Network Adapters # # CONFIG_USB_CATC is not set @@ -832,13 +835,31 @@ CONFIG_USB_PEGASUS=m # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -883,7 +904,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -946,6 +966,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="mem=32M console=ttyVR0,19200" diff --git a/arch/mips/configs/ocelot_3_defconfig b/arch/mips/configs/ocelot_3_defconfig index 925d8adef88..1ce4310fd92 100644 --- a/arch/mips/configs/ocelot_3_defconfig +++ b/arch/mips/configs/ocelot_3_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:18 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:10 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MOMENCO_OCELOT_3=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -120,7 +122,6 @@ CONFIG_RM7000_CPU_SCACHE=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -144,7 +145,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -161,6 +161,7 @@ CONFIG_SYSCTL=y # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -174,10 +175,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -189,7 +186,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_KMOD=y @@ -198,6 +194,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -217,7 +215,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -245,6 +242,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -266,6 +264,7 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y @@ -278,9 +277,12 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_IP_VS is not set CONFIG_IPV6=m # CONFIG_IPV6_PRIVACY is not set +CONFIG_IPV6_ROUTER_PREF=y +CONFIG_IPV6_ROUTE_INFO=y # CONFIG_INET6_AH is not set # CONFIG_INET6_ESP is not set # CONFIG_INET6_IPCOMP is not set +# CONFIG_INET6_XFRM_TUNNEL is not set # CONFIG_INET6_TUNNEL is not set # CONFIG_IPV6_TUNNEL is not set CONFIG_NETFILTER=y @@ -299,10 +301,13 @@ CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m @@ -332,6 +337,11 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -341,11 +351,6 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -367,6 +372,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -411,7 +419,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set # CONFIG_CDROM_PKTCDVD is not set CONFIG_ATA_OVER_ETH=m @@ -475,7 +483,6 @@ CONFIG_ISCSI_TCP=m # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set -# CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_QLOGIC_1280 is not set # CONFIG_SCSI_QLA_FC is not set # CONFIG_SCSI_LPFC is not set @@ -690,6 +697,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -699,6 +707,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -756,10 +765,6 @@ CONFIG_RTC=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -777,6 +782,7 @@ CONFIG_FB=y # CONFIG_FB_CFB_COPYAREA is not set # CONFIG_FB_CFB_IMAGEBLIT is not set # CONFIG_FB_MACMODES is not set +CONFIG_FB_FIRMWARE_EDID=y CONFIG_FB_MODE_HELPERS=y # CONFIG_FB_TILEBLITTING is not set # CONFIG_FB_CIRRUS is not set @@ -788,7 +794,6 @@ CONFIG_FB_MODE_HELPERS=y # CONFIG_FB_NVIDIA is not set # CONFIG_FB_RIVA is not set # CONFIG_FB_MATROX is not set -# CONFIG_FB_RADEON_OLD is not set # CONFIG_FB_RADEON is not set # CONFIG_FB_ATY128 is not set # CONFIG_FB_ATY is not set @@ -832,6 +837,7 @@ CONFIG_LOGO_LINUX_CLUT224=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -849,13 +855,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -914,7 +938,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -1025,6 +1048,7 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="ip=any root=nfs" diff --git a/arch/mips/configs/ocelot_c_defconfig b/arch/mips/configs/ocelot_c_defconfig index ee1cf9b9eb9..8a6aa5012f8 100644 --- a/arch/mips/configs/ocelot_c_defconfig +++ b/arch/mips/configs/ocelot_c_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:19 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:10 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MOMENCO_OCELOT_C=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -139,7 +141,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -155,6 +156,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -168,10 +170,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -185,6 +183,7 @@ CONFIG_BASE_SMALL=0 # # Block layer # +# CONFIG_BLK_DEV_IO_TRACE is not set # # IO Schedulers @@ -204,7 +203,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -222,6 +220,7 @@ CONFIG_MMU=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set +# CONFIG_BUILD_ELF64 is not set CONFIG_MIPS32_COMPAT=y CONFIG_COMPAT=y CONFIG_MIPS32_O32=y @@ -236,6 +235,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set # CONFIG_PACKET is not set CONFIG_UNIX=y CONFIG_XFRM=y @@ -256,12 +256,15 @@ CONFIG_IP_PNP_DHCP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=y +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -273,6 +276,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -282,11 +290,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -307,6 +310,9 @@ CONFIG_IEEE80211=y # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=y CONFIG_IEEE80211_CRYPT_CCMP=y +CONFIG_IEEE80211_SOFTMAC=y +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -351,7 +357,7 @@ CONFIG_PROC_EVENTS=y # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=y CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -542,6 +548,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -551,6 +558,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -609,10 +617,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -643,6 +647,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -660,13 +665,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -711,7 +734,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=y # CONFIG_CONFIGFS_FS is not set # @@ -778,6 +800,8 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set +# CONFIG_UNWIND_INFO is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/ocelot_defconfig b/arch/mips/configs/ocelot_defconfig index d80ff278f2a..f9ee35eeb76 100644 --- a/arch/mips/configs/ocelot_defconfig +++ b/arch/mips/configs/ocelot_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:20 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:11 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MOMENCO_OCELOT=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -121,7 +123,6 @@ CONFIG_RM7000_CPU_SCACHE=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -144,7 +145,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -160,6 +160,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -173,10 +174,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -191,6 +188,8 @@ CONFIG_BASE_SMALL=0 # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -236,6 +235,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set # CONFIG_PACKET is not set CONFIG_UNIX=y CONFIG_XFRM=y @@ -256,12 +256,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=y +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -273,6 +276,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -282,11 +290,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -307,6 +310,9 @@ CONFIG_IEEE80211=y # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=y CONFIG_IEEE80211_CRYPT_CCMP=y +CONFIG_IEEE80211_SOFTMAC=y +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -346,7 +352,7 @@ CONFIG_PROC_EVENTS=y # CONFIG_BLK_DEV_LOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=y CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -563,10 +569,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -597,6 +599,7 @@ CONFIG_DUMMY_CONSOLE=y # # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -613,12 +616,30 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -663,7 +684,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=y # CONFIG_CONFIGFS_FS is not set # @@ -730,6 +750,8 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set +# CONFIG_UNWIND_INFO is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/ocelot_g_defconfig b/arch/mips/configs/ocelot_g_defconfig index c0f508d180c..b48bdee2411 100644 --- a/arch/mips/configs/ocelot_g_defconfig +++ b/arch/mips/configs/ocelot_g_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:21 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:11 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MOMENCO_OCELOT_G=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -142,7 +144,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -158,6 +159,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -171,10 +173,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -188,6 +186,7 @@ CONFIG_BASE_SMALL=0 # # Block layer # +# CONFIG_BLK_DEV_IO_TRACE is not set # # IO Schedulers @@ -207,7 +206,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -225,6 +223,7 @@ CONFIG_MMU=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set +# CONFIG_BUILD_ELF64 is not set CONFIG_MIPS32_COMPAT=y CONFIG_COMPAT=y CONFIG_MIPS32_O32=y @@ -239,6 +238,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set # CONFIG_PACKET is not set CONFIG_UNIX=y CONFIG_XFRM=y @@ -259,12 +259,15 @@ CONFIG_IP_PNP_DHCP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=y +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -276,6 +279,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -285,11 +293,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -310,6 +313,9 @@ CONFIG_IEEE80211=y # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=y CONFIG_IEEE80211_CRYPT_CCMP=y +CONFIG_IEEE80211_SOFTMAC=y +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -354,7 +360,7 @@ CONFIG_PROC_EVENTS=y # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=y CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -545,6 +551,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -554,6 +561,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -612,10 +620,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -646,6 +650,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -663,13 +668,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -714,7 +737,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=y # CONFIG_CONFIGFS_FS is not set # @@ -781,6 +803,8 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set +# CONFIG_UNWIND_INFO is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/pb1100_defconfig b/arch/mips/configs/pb1100_defconfig index 194b3c772bb..01aac40634b 100644 --- a/arch/mips/configs/pb1100_defconfig +++ b/arch/mips/configs/pb1100_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:22 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:12 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_PB1100=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -116,11 +118,11 @@ CONFIG_PAGE_SIZE_4KB=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set CONFIG_64BIT_PHYS_ADDR=y -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -138,7 +140,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -154,6 +155,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -167,10 +169,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -183,7 +181,6 @@ CONFIG_OBSOLETE_INTERMODULE=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -192,6 +189,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -247,6 +246,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -269,7 +269,8 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -280,6 +281,8 @@ CONFIG_TCP_CONG_BIC=y # # CONFIG_IP_VS is not set # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set @@ -296,10 +299,13 @@ CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m @@ -323,6 +329,11 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -332,11 +343,6 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -358,6 +364,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -414,7 +423,6 @@ CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_CFI_INTELEXT is not set CONFIG_MTD_CFI_AMDSTD=y -CONFIG_MTD_CFI_AMDSTD_RETRY=0 # CONFIG_MTD_CFI_STAA is not set CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set @@ -436,7 +444,6 @@ CONFIG_MTD_ALCHEMY=y # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLKMTD is not set # CONFIG_MTD_BLOCK2MTD is not set # @@ -473,7 +480,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -716,10 +723,6 @@ CONFIG_SYNCLINK_CS=m # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -750,6 +753,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +# CONFIG_USB_ARCH_HAS_EHCI is not set # CONFIG_USB is not set # @@ -767,12 +771,30 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -830,7 +852,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -939,6 +960,7 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/pb1500_defconfig b/arch/mips/configs/pb1500_defconfig index 8985725e6a9..398c3c265b9 100644 --- a/arch/mips/configs/pb1500_defconfig +++ b/arch/mips/configs/pb1500_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:24 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:13 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_PB1500=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -115,11 +117,11 @@ CONFIG_PAGE_SIZE_4KB=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set CONFIG_64BIT_PHYS_ADDR=y -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -137,7 +139,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -153,6 +154,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -166,10 +168,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -182,7 +180,6 @@ CONFIG_OBSOLETE_INTERMODULE=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -191,6 +188,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -210,7 +209,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -253,6 +251,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -275,7 +274,8 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -286,6 +286,8 @@ CONFIG_TCP_CONG_BIC=y # # CONFIG_IP_VS is not set # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set @@ -302,10 +304,13 @@ CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m @@ -329,6 +334,11 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -338,11 +348,6 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -364,6 +369,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -420,7 +428,6 @@ CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_CFI_INTELEXT is not set CONFIG_MTD_CFI_AMDSTD=y -CONFIG_MTD_CFI_AMDSTD_RETRY=0 # CONFIG_MTD_CFI_STAA is not set CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set @@ -443,7 +450,6 @@ CONFIG_MTD_ALCHEMY=y # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLKMTD is not set # CONFIG_MTD_BLOCK2MTD is not set # @@ -485,7 +491,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -750,6 +756,7 @@ CONFIG_SERIO_RAW=m # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y # CONFIG_SERIAL_8250_CS is not set CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 @@ -761,6 +768,7 @@ CONFIG_SERIAL_8250_AU1X00=y # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -826,10 +834,6 @@ CONFIG_SYNCLINK_CS=m # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -854,6 +858,7 @@ CONFIG_SYNCLINK_CS=m # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -871,13 +876,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -935,7 +958,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -1044,6 +1066,7 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/pb1550_defconfig b/arch/mips/configs/pb1550_defconfig index adbf997b540..ea282a53bb6 100644 --- a/arch/mips/configs/pb1550_defconfig +++ b/arch/mips/configs/pb1550_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:25 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:13 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_PB1550=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -115,11 +117,11 @@ CONFIG_PAGE_SIZE_4KB=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set CONFIG_64BIT_PHYS_ADDR=y -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -137,7 +139,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -153,6 +154,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -166,10 +168,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -182,7 +180,6 @@ CONFIG_OBSOLETE_INTERMODULE=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -191,6 +188,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -210,7 +209,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -253,6 +251,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -275,7 +274,8 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -286,6 +286,8 @@ CONFIG_TCP_CONG_BIC=y # # CONFIG_IP_VS is not set # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set @@ -302,10 +304,13 @@ CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m @@ -329,6 +334,11 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -338,11 +348,6 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -364,6 +369,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -420,7 +428,6 @@ CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_CFI_INTELEXT is not set CONFIG_MTD_CFI_AMDSTD=y -CONFIG_MTD_CFI_AMDSTD_RETRY=0 # CONFIG_MTD_CFI_STAA is not set CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set @@ -443,7 +450,6 @@ CONFIG_MTD_ALCHEMY=y # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLKMTD is not set # CONFIG_MTD_BLOCK2MTD is not set # @@ -485,7 +491,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -742,6 +748,7 @@ CONFIG_SERIO_RAW=m # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y # CONFIG_SERIAL_8250_CS is not set CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 @@ -753,6 +760,7 @@ CONFIG_SERIAL_8250_AU1X00=y # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -818,10 +826,6 @@ CONFIG_SYNCLINK_CS=m # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -846,6 +850,7 @@ CONFIG_SYNCLINK_CS=m # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -863,13 +868,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -927,7 +950,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -1036,6 +1058,7 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/pnx8550-jbs_defconfig b/arch/mips/configs/pnx8550-jbs_defconfig index b5db700450b..4c57e564db0 100644 --- a/arch/mips/configs/pnx8550-jbs_defconfig +++ b/arch/mips/configs/pnx8550-jbs_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:26 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:14 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_PNX8550_JBS=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -114,11 +116,11 @@ CONFIG_PAGE_SIZE_4KB=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -136,7 +138,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -153,6 +154,7 @@ CONFIG_SYSCTL=y # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y +# CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -167,10 +169,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -181,7 +179,6 @@ CONFIG_BASE_SMALL=0 # CONFIG_MODULES=y # CONFIG_MODULE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_KMOD=y @@ -190,6 +187,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -209,7 +208,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -# CONFIG_PCI_LEGACY_PROC is not set # CONFIG_PCI_DEBUG is not set CONFIG_MMU=y @@ -238,6 +236,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -257,12 +256,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -274,6 +276,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -283,11 +290,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -469,7 +471,6 @@ CONFIG_ISCSI_TCP=m # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set -# CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_QLOGIC_1280 is not set # CONFIG_SCSI_QLA_FC is not set # CONFIG_SCSI_LPFC is not set @@ -671,6 +672,7 @@ CONFIG_HW_CONSOLE=y # Non-8250 serial port support # # CONFIG_SERIAL_IP3106 is not set +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -723,6 +725,7 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_HWMON=y # CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_F71805F is not set # CONFIG_HWMON_DEBUG_CHIP is not set # @@ -730,10 +733,6 @@ CONFIG_HWMON=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -742,6 +741,7 @@ CONFIG_HWMON=y # Digital Video Broadcasting Devices # # CONFIG_DVB is not set +# CONFIG_USB_DABUSB is not set # # Graphics support @@ -764,6 +764,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y # CONFIG_USB_DEBUG is not set @@ -827,9 +828,7 @@ CONFIG_USB_STORAGE_JUMPSHOT=y # CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set -# CONFIG_USB_MTOUCH is not set -# CONFIG_USB_ITMTOUCH is not set -# CONFIG_USB_EGALAX is not set +# CONFIG_USB_TOUCHSCREEN is not set # CONFIG_USB_YEALINK is not set # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set @@ -844,15 +843,6 @@ CONFIG_USB_STORAGE_JUMPSHOT=y # CONFIG_USB_MICROTEK is not set # -# USB Multimedia devices -# -# CONFIG_USB_DABUSB is not set - -# -# Video4Linux support is needed for USB Multimedia device support -# - -# # USB Network Adapters # # CONFIG_USB_CATC is not set @@ -902,13 +892,31 @@ CONFIG_USB_MON=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -956,7 +964,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -# CONFIG_RELAYFS_FS is not set # CONFIG_CONFIGFS_FS is not set # @@ -1067,6 +1074,7 @@ CONFIG_LOG_BUF_SHIFT=14 CONFIG_DETECT_SOFTLOCKUP=y # CONFIG_SCHEDSTATS is not set CONFIG_DEBUG_SLAB=y +# CONFIG_DEBUG_SLAB_LEAK is not set CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set diff --git a/arch/mips/configs/pnx8550-v2pci_defconfig b/arch/mips/configs/pnx8550-v2pci_defconfig index 4187287f076..3c8f35162fe 100644 --- a/arch/mips/configs/pnx8550-v2pci_defconfig +++ b/arch/mips/configs/pnx8550-v2pci_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:28 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:14 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_PNX8550_V2PCI=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -114,12 +116,11 @@ CONFIG_PAGE_SIZE_4KB=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -CONFIG_CPU_ADVANCED=y CONFIG_CPU_HAS_LLSC=y -# CONFIG_CPU_HAS_WB is not set CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -137,7 +138,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -154,6 +154,7 @@ CONFIG_SYSCTL=y # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y +# CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -167,10 +168,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -181,7 +178,6 @@ CONFIG_BASE_SMALL=0 # CONFIG_MODULES=y # CONFIG_MODULE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_KMOD=y @@ -190,6 +186,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -209,7 +207,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -# CONFIG_PCI_LEGACY_PROC is not set CONFIG_MMU=y # @@ -237,6 +234,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -256,6 +254,7 @@ CONFIG_IP_PNP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y @@ -268,9 +267,12 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_IP_VS is not set CONFIG_IPV6=m # CONFIG_IPV6_PRIVACY is not set +CONFIG_IPV6_ROUTER_PREF=y +CONFIG_IPV6_ROUTE_INFO=y # CONFIG_INET6_AH is not set # CONFIG_INET6_ESP is not set # CONFIG_INET6_IPCOMP is not set +# CONFIG_INET6_XFRM_TUNNEL is not set # CONFIG_INET6_TUNNEL is not set # CONFIG_IPV6_TUNNEL is not set CONFIG_NETFILTER=y @@ -287,10 +289,12 @@ CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m @@ -320,6 +324,11 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -329,11 +338,6 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -521,7 +525,6 @@ CONFIG_AIC7XXX_DEBUG_MASK=0 # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set -# CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_QLOGIC_1280 is not set # CONFIG_SCSI_QLA_FC is not set # CONFIG_SCSI_LPFC is not set @@ -757,6 +760,7 @@ CONFIG_SERIAL_NONSTANDARD=y # Non-8250 serial port support # # CONFIG_SERIAL_IP3106 is not set +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -816,7 +820,6 @@ CONFIG_I2C_ALGOBIT=m # CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_PROSAVAGE is not set # CONFIG_I2C_SAVAGE4 is not set -# CONFIG_SCx200_ACB is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set # CONFIG_I2C_SIS96X is not set @@ -835,9 +838,7 @@ CONFIG_I2C_ALGOBIT=m # CONFIG_SENSORS_PCF8574 is not set # CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set -# CONFIG_SENSORS_RTC8564 is not set # CONFIG_SENSORS_MAX6875 is not set -# CONFIG_RTC_X1205_I2C is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set @@ -867,6 +868,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ASB100 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_F71805F is not set # CONFIG_SENSORS_FSCHER is not set # CONFIG_SENSORS_FSCPOS is not set # CONFIG_SENSORS_GL518SM is not set @@ -901,10 +903,6 @@ CONFIG_HWMON=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -913,6 +911,7 @@ CONFIG_HWMON=y # Digital Video Broadcasting Devices # # CONFIG_DVB is not set +# CONFIG_USB_DABUSB is not set # # Graphics support @@ -922,6 +921,7 @@ CONFIG_FB=y # CONFIG_FB_CFB_COPYAREA is not set # CONFIG_FB_CFB_IMAGEBLIT is not set # CONFIG_FB_MACMODES is not set +CONFIG_FB_FIRMWARE_EDID=y # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set # CONFIG_FB_CIRRUS is not set @@ -933,7 +933,6 @@ CONFIG_FB=y # CONFIG_FB_NVIDIA is not set # CONFIG_FB_RIVA is not set # CONFIG_FB_MATROX is not set -# CONFIG_FB_RADEON_OLD is not set # CONFIG_FB_RADEON is not set # CONFIG_FB_ATY128 is not set # CONFIG_FB_ATY is not set @@ -970,6 +969,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y # CONFIG_USB_DEBUG is not set @@ -1030,9 +1030,7 @@ CONFIG_USB_HIDDEV=y # CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set -# CONFIG_USB_MTOUCH is not set -# CONFIG_USB_ITMTOUCH is not set -# CONFIG_USB_EGALAX is not set +# CONFIG_USB_TOUCHSCREEN is not set # CONFIG_USB_YEALINK is not set # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set @@ -1047,15 +1045,6 @@ CONFIG_USB_HIDDEV=y # CONFIG_USB_MICROTEK is not set # -# USB Multimedia devices -# -# CONFIG_USB_DABUSB is not set - -# -# Video4Linux support is needed for USB Multimedia device support -# - -# # USB Network Adapters # # CONFIG_USB_CATC is not set @@ -1106,13 +1095,31 @@ CONFIG_USB_MON=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -1171,7 +1178,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -# CONFIG_RELAYFS_FS is not set # CONFIG_CONFIGFS_FS is not set # @@ -1280,6 +1286,7 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/qemu_defconfig b/arch/mips/configs/qemu_defconfig index 31f5afabafa..4bcc01dea04 100644 --- a/arch/mips/configs/qemu_defconfig +++ b/arch/mips/configs/qemu_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc2 -# Sun Feb 12 19:18:55 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:15 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_QEMU=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_COHERENT=y CONFIG_GENERIC_ISA_DMA=y @@ -115,16 +117,17 @@ CONFIG_PAGE_SIZE_4KB=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_SMP is not set CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set @@ -147,6 +150,7 @@ CONFIG_LOCALVERSION_AUTO=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" CONFIG_EMBEDDED=y CONFIG_KALLSYMS=y @@ -159,10 +163,6 @@ CONFIG_ELF_CORE=y # CONFIG_FUTEX is not set # CONFIG_EPOLL is not set # CONFIG_SHMEM is not set -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y CONFIG_TINY_SHMEM=y CONFIG_BASE_SMALL=1 @@ -177,6 +177,8 @@ CONFIG_BASE_SMALL=1 # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -196,6 +198,7 @@ CONFIG_DEFAULT_IOSCHED="noop" # CONFIG_ISA=y CONFIG_MMU=y +CONFIG_I8253=y # # PCCARD (PCMCIA/CardBus) support @@ -241,12 +244,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -308,7 +314,7 @@ CONFIG_PROC_EVENTS=y # CONFIG_BLK_DEV_LOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set @@ -530,10 +536,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -552,6 +554,7 @@ CONFIG_LEGACY_PTY_COUNT=256 # Console display driver support # CONFIG_VGA_CONSOLE=y +# CONFIG_VGACON_SOFT_SCROLLBACK is not set # CONFIG_MDA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y @@ -565,6 +568,7 @@ CONFIG_DUMMY_CONSOLE=y # # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -581,15 +585,28 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) # # -# EDAC - error detection and reporting (RAS) +# Real Time Clock # # @@ -632,7 +649,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=y # # Miscellaneous filesystems @@ -680,6 +696,8 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set +# CONFIG_UNWIND_INFO is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/rbhma4500_defconfig b/arch/mips/configs/rbhma4500_defconfig index b126f763cf5..3d441932e43 100644 --- a/arch/mips/configs/rbhma4500_defconfig +++ b/arch/mips/configs/rbhma4500_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:30 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:16 2006 # CONFIG_MIPS=y @@ -71,6 +71,8 @@ CONFIG_TOSHIBA_RBTX4938_MPLEX_PIO58_61=y # CONFIG_TOSHIBA_RBTX4938_MPLEX_NAND is not set # CONFIG_TOSHIBA_RBTX4938_MPLEX_ATA is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -121,10 +123,9 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_8KB is not set # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set +CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set -CONFIG_CPU_ADVANCED=y CONFIG_CPU_HAS_LLSC=y -CONFIG_CPU_HAS_WB=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y @@ -145,7 +146,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -162,6 +162,7 @@ CONFIG_SYSCTL=y # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -175,10 +176,6 @@ CONFIG_BASE_FULL=y # CONFIG_FUTEX is not set # CONFIG_EPOLL is not set CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -190,7 +187,6 @@ CONFIG_OBSOLETE_INTERMODULE=y # CONFIG_MODULES=y # CONFIG_MODULE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_KMOD=y @@ -199,6 +195,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -218,7 +216,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -# CONFIG_PCI_LEGACY_PROC is not set CONFIG_ISA=y CONFIG_MMU=y @@ -247,6 +244,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y @@ -267,6 +265,7 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y @@ -279,9 +278,12 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_IP_VS is not set CONFIG_IPV6=m # CONFIG_IPV6_PRIVACY is not set +CONFIG_IPV6_ROUTER_PREF=y +CONFIG_IPV6_ROUTE_INFO=y # CONFIG_INET6_AH is not set # CONFIG_INET6_ESP is not set # CONFIG_INET6_IPCOMP is not set +# CONFIG_INET6_XFRM_TUNNEL is not set # CONFIG_INET6_TUNNEL is not set # CONFIG_IPV6_TUNNEL is not set CONFIG_NETFILTER=y @@ -300,10 +302,12 @@ CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m @@ -333,6 +337,11 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -342,11 +351,6 @@ CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -369,6 +373,9 @@ CONFIG_IEEE80211=m CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m CONFIG_IEEE80211_CRYPT_TKIP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -425,7 +432,6 @@ CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I8 is not set CONFIG_MTD_CFI_INTELEXT=y CONFIG_MTD_CFI_AMDSTD=y -CONFIG_MTD_CFI_AMDSTD_RETRY=0 # CONFIG_MTD_CFI_STAA is not set CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set @@ -447,7 +453,6 @@ CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLKMTD is not set # CONFIG_MTD_BLOCK2MTD is not set # @@ -702,6 +707,7 @@ CONFIG_NET_PCI=y # Wireless LAN (non-hamradio) # CONFIG_NET_RADIO=y +# CONFIG_NET_WIRELESS_RTNETLINK is not set # # Obsolete Wireless cards support (pre-802.11) @@ -715,6 +721,8 @@ CONFIG_NET_RADIO=y # # CONFIG_IPW2100 is not set CONFIG_IPW2200=m +# CONFIG_IPW2200_MONITOR is not set +# CONFIG_IPW_QOS is not set # CONFIG_IPW2200_DEBUG is not set # CONFIG_HERMES is not set # CONFIG_ATMEL is not set @@ -724,6 +732,7 @@ CONFIG_IPW2200=m # # CONFIG_PRISM54 is not set # CONFIG_HOSTAP is not set +# CONFIG_BCM43XX is not set CONFIG_NET_WIRELESS=y # @@ -821,7 +830,12 @@ CONFIG_HW_CONSOLE=y # # Non-8250 serial port support # +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_TXX9=y CONFIG_HAS_TXX9_SERIAL=y +# CONFIG_SERIAL_TXX9_CONSOLE is not set +# CONFIG_SERIAL_TXX9_STDSERIAL is not set +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -874,6 +888,7 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_HWMON=y # CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_F71805F is not set # CONFIG_HWMON_DEBUG_CHIP is not set # @@ -881,10 +896,6 @@ CONFIG_HWMON=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -893,6 +904,7 @@ CONFIG_HWMON=y # Digital Video Broadcasting Devices # # CONFIG_DVB is not set +# CONFIG_USB_DABUSB is not set # # Graphics support @@ -902,6 +914,7 @@ CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_MACMODES is not set +CONFIG_FB_FIRMWARE_EDID=y # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set # CONFIG_FB_CIRRUS is not set @@ -913,7 +926,6 @@ CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_NVIDIA is not set # CONFIG_FB_RIVA is not set # CONFIG_FB_MATROX is not set -# CONFIG_FB_RADEON_OLD is not set # CONFIG_FB_RADEON is not set # CONFIG_FB_ATY128 is not set CONFIG_FB_ATY=y @@ -934,6 +946,7 @@ CONFIG_FB_ATY_CT=y # Console display driver support # CONFIG_VGA_CONSOLE=y +# CONFIG_VGACON_SOFT_SCROLLBACK is not set # CONFIG_MDA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y # CONFIG_FRAMEBUFFER_CONSOLE is not set @@ -954,6 +967,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y # CONFIG_USB_DEBUG is not set @@ -1003,9 +1017,7 @@ CONFIG_USB_HIDDEV=y # CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set -# CONFIG_USB_MTOUCH is not set -# CONFIG_USB_ITMTOUCH is not set -# CONFIG_USB_EGALAX is not set +# CONFIG_USB_TOUCHSCREEN is not set CONFIG_USB_YEALINK=m # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set @@ -1019,15 +1031,6 @@ CONFIG_USB_YEALINK=m # CONFIG_USB_MDC800 is not set # -# USB Multimedia devices -# -# CONFIG_USB_DABUSB is not set - -# -# Video4Linux support is needed for USB Multimedia device support -# - -# # USB Network Adapters # # CONFIG_USB_CATC is not set @@ -1078,13 +1081,31 @@ CONFIG_USB_MON=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -1148,7 +1169,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -1266,6 +1286,7 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/rm200_defconfig b/arch/mips/configs/rm200_defconfig index 463ed3dbf6a..edfb9679a25 100644 --- a/arch/mips/configs/rm200_defconfig +++ b/arch/mips/configs/rm200_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:31 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:16 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_SNI_RM200_PCI=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_ARC=y CONFIG_ARCH_MAY_HAVE_PC_FDC=y @@ -122,7 +124,6 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -145,7 +146,6 @@ CONFIG_PREEMPT_VOLUNTARY=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -163,6 +163,7 @@ CONFIG_SYSCTL=y # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -176,10 +177,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -191,7 +188,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_KMOD=y @@ -200,6 +196,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -220,10 +218,10 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_HW_HAS_EISA=y CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_ISA=y # CONFIG_EISA is not set CONFIG_MMU=y +CONFIG_I8253=y # # PCCARD (PCMCIA/CardBus) support @@ -250,6 +248,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=m CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -272,6 +271,7 @@ CONFIG_IP_PIMSM_V2=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set CONFIG_INET_TUNNEL=m CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y @@ -284,9 +284,12 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_IP_VS is not set CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y +CONFIG_IPV6_ROUTER_PREF=y +CONFIG_IPV6_ROUTE_INFO=y CONFIG_INET6_AH=m CONFIG_INET6_ESP=m CONFIG_INET6_IPCOMP=m +CONFIG_INET6_XFRM_TUNNEL=m CONFIG_INET6_TUNNEL=m CONFIG_IPV6_TUNNEL=m CONFIG_NETFILTER=y @@ -309,11 +312,14 @@ CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_CONNMARK=m CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m @@ -337,20 +343,19 @@ CONFIG_IP_NF_IRC=m CONFIG_IP_NF_TFTP=m CONFIG_IP_NF_AMANDA=m CONFIG_IP_NF_PPTP=m +CONFIG_IP_NF_H323=m CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_IPRANGE=m -CONFIG_IP_NF_MATCH_MULTIPORT=m CONFIG_IP_NF_MATCH_TOS=m CONFIG_IP_NF_MATCH_RECENT=m CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_DSCP=m -CONFIG_IP_NF_MATCH_AH_ESP=m +CONFIG_IP_NF_MATCH_AH=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_MATCH_OWNER=m CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_HASHLIMIT=m -CONFIG_IP_NF_MATCH_POLICY=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -368,6 +373,7 @@ CONFIG_IP_NF_NAT_FTP=m CONFIG_IP_NF_NAT_TFTP=m CONFIG_IP_NF_NAT_AMANDA=m CONFIG_IP_NF_NAT_PPTP=m +CONFIG_IP_NF_NAT_H323=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_TOS=m CONFIG_IP_NF_TARGET_ECN=m @@ -388,12 +394,10 @@ CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_FRAG=m CONFIG_IP6_NF_MATCH_HL=m -CONFIG_IP6_NF_MATCH_MULTIPORT=m CONFIG_IP6_NF_MATCH_OWNER=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AHESP=m +CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_MATCH_POLICY=m CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_LOG=m CONFIG_IP6_NF_TARGET_REJECT=m @@ -439,21 +443,22 @@ CONFIG_BRIDGE_EBT_ULOG=m # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set CONFIG_BRIDGE=m # CONFIG_VLAN_8021Q is not set CONFIG_DECNET=m # CONFIG_DECNET_ROUTER is not set +CONFIG_LLC=m # CONFIG_LLC2 is not set # CONFIG_IPX is not set # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -533,6 +538,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -620,6 +628,7 @@ CONFIG_BLK_DEV_UB=m CONFIG_BLK_DEV_RAM=m CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=4096 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -700,12 +709,11 @@ CONFIG_SCSI_SYM53C8XX_2=y CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1 CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16 CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64 -# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set +CONFIG_SCSI_SYM53C8XX_MMIO=y # CONFIG_SCSI_IPR is not set # CONFIG_SCSI_PAS16 is not set # CONFIG_SCSI_PSI240I is not set # CONFIG_SCSI_QLOGIC_FAS is not set -# CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_QLOGIC_1280 is not set # CONFIG_SCSI_QLA_FC is not set # CONFIG_SCSI_LPFC is not set @@ -731,6 +739,7 @@ CONFIG_MD_RAID0=m CONFIG_MD_RAID1=m CONFIG_MD_RAID10=m CONFIG_MD_RAID5=m +CONFIG_MD_RAID5_RESHAPE=y # CONFIG_MD_RAID6 is not set CONFIG_MD_MULTIPATH=m CONFIG_MD_FAULTY=m @@ -965,6 +974,7 @@ CONFIG_HW_CONSOLE=y # Serial drivers # CONFIG_SERIAL_8250=m +CONFIG_SERIAL_8250_PCI=m CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 CONFIG_SERIAL_8250_EXTENDED=y @@ -977,6 +987,7 @@ CONFIG_SERIAL_8250_RSA=y # Non-8250 serial port support # CONFIG_SERIAL_CORE=m +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -1027,12 +1038,19 @@ CONFIG_RTC=m # Dallas's 1-wire bus # CONFIG_W1=m -CONFIG_W1_MATROX=m -CONFIG_W1_DS9490=m -# CONFIG_W1_DS9490_BRIDGE is not set -CONFIG_W1_THERM=m -CONFIG_W1_SMEM=m -# CONFIG_W1_DS2433 is not set + +# +# 1-wire Bus Masters +# +# CONFIG_W1_MASTER_MATROX is not set +# CONFIG_W1_MASTER_DS9490 is not set + +# +# 1-wire Slaves +# +# CONFIG_W1_SLAVE_THERM is not set +# CONFIG_W1_SLAVE_SMEM is not set +# CONFIG_W1_SLAVE_DS2433 is not set # # Hardware Monitoring support @@ -1045,10 +1063,6 @@ CONFIG_W1_SMEM=m # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -1057,6 +1071,7 @@ CONFIG_W1_SMEM=m # Digital Video Broadcasting Devices # # CONFIG_DVB is not set +CONFIG_USB_DABUSB=m # # Graphics support @@ -1067,6 +1082,7 @@ CONFIG_W1_SMEM=m # Console display driver support # CONFIG_VGA_CONSOLE=y +# CONFIG_VGACON_SOFT_SCROLLBACK is not set # CONFIG_MDA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y @@ -1080,6 +1096,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=m # CONFIG_USB_DEBUG is not set @@ -1151,9 +1168,7 @@ CONFIG_USB_WACOM=m # CONFIG_USB_ACECAD is not set CONFIG_USB_KBTAB=m CONFIG_USB_POWERMATE=m -# CONFIG_USB_MTOUCH is not set -# CONFIG_USB_ITMTOUCH is not set -CONFIG_USB_EGALAX=m +# CONFIG_USB_TOUCHSCREEN is not set CONFIG_USB_YEALINK=m CONFIG_USB_XPAD=m # CONFIG_USB_ATI_REMOTE is not set @@ -1168,15 +1183,6 @@ CONFIG_USB_MDC800=m CONFIG_USB_MICROTEK=m # -# USB Multimedia devices -# -CONFIG_USB_DABUSB=m - -# -# Video4Linux support is needed for USB Multimedia device support -# - -# # USB Network Adapters # CONFIG_USB_CATC=m @@ -1213,6 +1219,7 @@ CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m CONFIG_USB_SERIAL_CYPRESS_M8=m CONFIG_USB_SERIAL_EMPEG=m CONFIG_USB_SERIAL_FTDI_SIO=m +# CONFIG_USB_SERIAL_FUNSOFT is not set CONFIG_USB_SERIAL_VISOR=m CONFIG_USB_SERIAL_IPAQ=m CONFIG_USB_SERIAL_IR=m @@ -1237,6 +1244,7 @@ CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y CONFIG_USB_SERIAL_KLSI=m CONFIG_USB_SERIAL_KOBIL_SCT=m CONFIG_USB_SERIAL_MCT_U232=m +# CONFIG_USB_SERIAL_NAVMAN is not set CONFIG_USB_SERIAL_PL2303=m CONFIG_USB_SERIAL_HP4X=m CONFIG_USB_SERIAL_SAFE=m @@ -1281,13 +1289,31 @@ CONFIG_USB_TEST=m # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -1358,7 +1384,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -1379,7 +1404,6 @@ CONFIG_HPFS_FS=m CONFIG_QNX4FS_FS=m CONFIG_SYSV_FS=m CONFIG_UFS_FS=m -# CONFIG_UFS_FS_WRITE is not set # # Network File Systems @@ -1500,6 +1524,7 @@ CONFIG_NLS_UTF8=m # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/sb1250-swarm_defconfig b/arch/mips/configs/sb1250-swarm_defconfig index da68c3f7205..e388a3dae0a 100644 --- a/arch/mips/configs/sb1250-swarm_defconfig +++ b/arch/mips/configs/sb1250-swarm_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:32 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:17 2006 # CONFIG_MIPS=y @@ -81,6 +81,8 @@ CONFIG_SIBYTE_CFE=y # CONFIG_SIBYTE_SB1250_PROF is not set # CONFIG_SIBYTE_TBPROF is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_COHERENT=y CONFIG_CPU_BIG_ENDIAN=y @@ -158,7 +160,6 @@ CONFIG_PREEMPT_BKL=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_LOCK_KERNEL=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -175,6 +176,7 @@ CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_CPUSETS=y +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -188,10 +190,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -203,7 +201,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -212,6 +209,7 @@ CONFIG_STOP_MACHINE=y # # Block layer # +# CONFIG_BLK_DEV_IO_TRACE is not set # # IO Schedulers @@ -231,7 +229,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y CONFIG_MMU=y # @@ -249,6 +246,7 @@ CONFIG_MMU=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set +# CONFIG_BUILD_ELF64 is not set CONFIG_MIPS32_COMPAT=y CONFIG_COMPAT=y CONFIG_MIPS32_O32=y @@ -263,6 +261,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -284,12 +283,15 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -301,6 +303,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -310,11 +317,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -335,6 +337,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -589,6 +594,7 @@ CONFIG_SIBYTE_SB1250_DUART_CONSOLE=y # # Non-8250 serial port support # +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -647,10 +653,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -675,6 +677,7 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -692,13 +695,31 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -746,7 +767,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -812,6 +832,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=15 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" # CONFIG_SB1XXX_CORELIS is not set diff --git a/arch/mips/configs/sead_defconfig b/arch/mips/configs/sead_defconfig index 9a936d7b7c0..6b8a6a416a2 100644 --- a/arch/mips/configs/sead_defconfig +++ b/arch/mips/configs/sead_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:33 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:17 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_MIPS_SEAD=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -118,11 +120,11 @@ CONFIG_PAGE_SIZE_4KB=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -140,7 +142,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -154,6 +155,7 @@ CONFIG_SYSVIPC=y # CONFIG_BSD_PROCESS_ACCT is not set CONFIG_SYSCTL=y # CONFIG_IKCONFIG is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -167,10 +169,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -185,6 +183,8 @@ CONFIG_BASE_SMALL=0 # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -296,12 +296,6 @@ CONFIG_RAID_ATTRS=y # # -# Network device support -# -# CONFIG_NETPOLL is not set -# CONFIG_NET_POLL_CONTROLLER is not set - -# # ISDN subsystem # @@ -397,10 +391,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -424,6 +414,7 @@ CONFIG_LEGACY_PTY_COUNT=256 # # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -440,12 +431,30 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -489,7 +498,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=y # CONFIG_CONFIGFS_FS is not set # @@ -543,6 +551,8 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set +# CONFIG_UNWIND_INFO is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/configs/tb0226_defconfig b/arch/mips/configs/tb0226_defconfig index c2dee0d1c72..dba0bdcdcf2 100644 --- a/arch/mips/configs/tb0226_defconfig +++ b/arch/mips/configs/tb0226_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:34 2006 +# Linux kernel version: 2.6.17-rc2 +# Tue Apr 25 00:08:41 2006 # CONFIG_MIPS=y @@ -68,12 +68,14 @@ CONFIG_MACH_VR41XX=y # CONFIG_NEC_CMBVR4133 is not set CONFIG_TANBAC_TB022X=y CONFIG_TANBAC_TB0226=y -CONFIG_TANBAC_TB0287=y +# CONFIG_TANBAC_TB0287 is not set # CONFIG_VICTOR_MPC30X is not set # CONFIG_ZAO_CAPCELLA is not set CONFIG_PCI_VR41XX=y # CONFIG_VRC4173 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -92,7 +94,7 @@ CONFIG_MIPS_L1_CACHE_SHIFT=5 # CONFIG_CPU_MIPS64_R2 is not set # CONFIG_CPU_R3000 is not set # CONFIG_CPU_TX39XX is not set -# CONFIG_CPU_VR41XX is not set +CONFIG_CPU_VR41XX=y # CONFIG_CPU_R4300 is not set # CONFIG_CPU_R4X00 is not set # CONFIG_CPU_TX49XX is not set @@ -105,18 +107,21 @@ CONFIG_MIPS_L1_CACHE_SHIFT=5 # CONFIG_CPU_RM7000 is not set # CONFIG_CPU_RM9000 is not set # CONFIG_CPU_SB1 is not set +CONFIG_SYS_HAS_CPU_VR41XX=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_64BIT_KERNEL=y # # Kernel type # -# CONFIG_32BIT is not set +CONFIG_32BIT=y # CONFIG_64BIT is not set CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_8KB is not set # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y @@ -137,7 +142,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -153,6 +157,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -166,10 +171,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -181,7 +182,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -189,6 +189,9 @@ CONFIG_KMOD=y # # Block layer # +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -208,7 +211,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -# CONFIG_PCI_LEGACY_PROC is not set CONFIG_MMU=y # @@ -226,6 +228,7 @@ CONFIG_MMU=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set +CONFIG_TRAD_SIGNALS=y # # Networking @@ -235,11 +238,10 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y -CONFIG_XFRM=y -CONFIG_XFRM_USER=m # CONFIG_NET_KEY is not set CONFIG_INET=y CONFIG_IP_MULTICAST=y @@ -263,12 +265,15 @@ CONFIG_SYN_COOKIES=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -280,6 +285,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -289,11 +299,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -310,10 +315,7 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_HAMRADIO is not set # CONFIG_IRDA is not set # CONFIG_BT is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m +# CONFIG_IEEE80211 is not set # # Device Drivers @@ -358,11 +360,12 @@ CONFIG_BLK_DEV_LOOP=m CONFIG_BLK_DEV_NBD=m # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_UB is not set -CONFIG_BLK_DEV_RAM=m +CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=4096 +# CONFIG_BLK_DEV_INITRD is not set # CONFIG_CDROM_PKTCDVD is not set -CONFIG_ATA_OVER_ETH=m +# CONFIG_ATA_OVER_ETH is not set # # ATA/ATAPI/MFM/RLL support @@ -397,14 +400,14 @@ CONFIG_SCSI_MULTI_LUN=y # SCSI Transport Attributes # # CONFIG_SCSI_SPI_ATTRS is not set -CONFIG_SCSI_FC_ATTRS=y -CONFIG_SCSI_ISCSI_ATTRS=m +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_ATTRS is not set # # SCSI low-level drivers # -CONFIG_ISCSI_TCP=m +# CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -424,7 +427,6 @@ CONFIG_ISCSI_TCP=m # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set -# CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_QLOGIC_1280 is not set # CONFIG_SCSI_QLA_FC is not set # CONFIG_SCSI_LPFC is not set @@ -507,8 +509,8 @@ CONFIG_NET_PCI=y # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set # CONFIG_DGRS is not set -CONFIG_EEPRO100=y -# CONFIG_E100 is not set +# CONFIG_EEPRO100 is not set +CONFIG_E100=y # CONFIG_FEALNX is not set # CONFIG_NATSEMI is not set # CONFIG_NE2K_PCI is not set @@ -625,6 +627,11 @@ CONFIG_HW_CONSOLE=y # # Non-8250 serial port support # +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_SERIAL_VR41XX=y +CONFIG_SERIAL_VR41XX_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -685,10 +692,6 @@ CONFIG_GPIO_VR41XX=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -697,6 +700,7 @@ CONFIG_GPIO_VR41XX=y # Digital Video Broadcasting Devices # # CONFIG_DVB is not set +# CONFIG_USB_DABUSB is not set # # Graphics support @@ -719,6 +723,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y # CONFIG_USB_DEBUG is not set @@ -756,7 +761,7 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y # # may also be needed; see USB_STORAGE Help for more information # -CONFIG_USB_STORAGE=m +CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set @@ -783,9 +788,7 @@ CONFIG_USB_STORAGE=m # CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set -# CONFIG_USB_MTOUCH is not set -# CONFIG_USB_ITMTOUCH is not set -# CONFIG_USB_EGALAX is not set +# CONFIG_USB_TOUCHSCREEN is not set # CONFIG_USB_YEALINK is not set # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set @@ -800,15 +803,6 @@ CONFIG_USB_STORAGE=m # CONFIG_USB_MICROTEK is not set # -# USB Multimedia devices -# -# CONFIG_USB_DABUSB is not set - -# -# Video4Linux support is needed for USB Multimedia device support -# - -# # USB Network Adapters # # CONFIG_USB_CATC is not set @@ -816,7 +810,7 @@ CONFIG_USB_STORAGE=m # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set # CONFIG_USB_USBNET is not set -CONFIG_USB_MON=y +# CONFIG_USB_MON is not set # # USB port drivers @@ -860,13 +854,48 @@ CONFIG_USB_MON=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock +# +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y + +# +# RTC drivers # +# CONFIG_RTC_DRV_M48T86 is not set +CONFIG_RTC_DRV_VR41XX=y +# CONFIG_RTC_DRV_TEST is not set # # File systems @@ -911,7 +940,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -952,9 +980,7 @@ CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set -CONFIG_SMB_FS=m -CONFIG_SMB_NLS_DEFAULT=y -CONFIG_SMB_NLS_REMOTE="cp932" +# CONFIG_SMB_FS is not set # CONFIG_CIFS is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set @@ -970,46 +996,7 @@ CONFIG_MSDOS_PARTITION=y # # Native Language Support # -CONFIG_NLS=y -CONFIG_NLS_DEFAULT="iso8859-1" -CONFIG_NLS_CODEPAGE_437=m -# CONFIG_NLS_CODEPAGE_737 is not set -# CONFIG_NLS_CODEPAGE_775 is not set -# CONFIG_NLS_CODEPAGE_850 is not set -# CONFIG_NLS_CODEPAGE_852 is not set -# CONFIG_NLS_CODEPAGE_855 is not set -# CONFIG_NLS_CODEPAGE_857 is not set -# CONFIG_NLS_CODEPAGE_860 is not set -# CONFIG_NLS_CODEPAGE_861 is not set -# CONFIG_NLS_CODEPAGE_862 is not set -# CONFIG_NLS_CODEPAGE_863 is not set -# CONFIG_NLS_CODEPAGE_864 is not set -# CONFIG_NLS_CODEPAGE_865 is not set -# CONFIG_NLS_CODEPAGE_866 is not set -# CONFIG_NLS_CODEPAGE_869 is not set -# CONFIG_NLS_CODEPAGE_936 is not set -# CONFIG_NLS_CODEPAGE_950 is not set -CONFIG_NLS_CODEPAGE_932=m -# CONFIG_NLS_CODEPAGE_949 is not set -# CONFIG_NLS_CODEPAGE_874 is not set -# CONFIG_NLS_ISO8859_8 is not set -# CONFIG_NLS_CODEPAGE_1250 is not set -# CONFIG_NLS_CODEPAGE_1251 is not set -# CONFIG_NLS_ASCII is not set -CONFIG_NLS_ISO8859_1=m -# CONFIG_NLS_ISO8859_2 is not set -# CONFIG_NLS_ISO8859_3 is not set -# CONFIG_NLS_ISO8859_4 is not set -# CONFIG_NLS_ISO8859_5 is not set -# CONFIG_NLS_ISO8859_6 is not set -# CONFIG_NLS_ISO8859_7 is not set -# CONFIG_NLS_ISO8859_9 is not set -# CONFIG_NLS_ISO8859_13 is not set -# CONFIG_NLS_ISO8859_14 is not set -# CONFIG_NLS_ISO8859_15 is not set -# CONFIG_NLS_KOI8_R is not set -# CONFIG_NLS_KOI8_U is not set -# CONFIG_NLS_UTF8 is not set +# CONFIG_NLS is not set # # Profiling support @@ -1023,44 +1010,20 @@ CONFIG_NLS_ISO8859_1=m # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="mem=32M console=ttyVR0,115200" # # Security options # -CONFIG_KEYS=y -CONFIG_KEYS_DEBUG_PROC_KEYS=y +# CONFIG_KEYS is not set # CONFIG_SECURITY is not set # # Cryptographic options # -CONFIG_CRYPTO=y -CONFIG_CRYPTO_HMAC=y -CONFIG_CRYPTO_NULL=m -CONFIG_CRYPTO_MD4=m -CONFIG_CRYPTO_MD5=m -CONFIG_CRYPTO_SHA1=m -CONFIG_CRYPTO_SHA256=m -CONFIG_CRYPTO_SHA512=m -CONFIG_CRYPTO_WP512=m -CONFIG_CRYPTO_TGR192=m -CONFIG_CRYPTO_DES=m -CONFIG_CRYPTO_BLOWFISH=m -CONFIG_CRYPTO_TWOFISH=m -CONFIG_CRYPTO_SERPENT=m -CONFIG_CRYPTO_AES=m -CONFIG_CRYPTO_CAST5=m -CONFIG_CRYPTO_CAST6=m -CONFIG_CRYPTO_TEA=m -CONFIG_CRYPTO_ARC4=m -CONFIG_CRYPTO_KHAZAD=m -CONFIG_CRYPTO_ANUBIS=m -CONFIG_CRYPTO_DEFLATE=m -CONFIG_CRYPTO_MICHAEL_MIC=m -CONFIG_CRYPTO_CRC32C=m -# CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO is not set # # Hardware crypto devices @@ -1069,9 +1032,8 @@ CONFIG_CRYPTO_CRC32C=m # # Library routines # -CONFIG_CRC_CCITT=m -CONFIG_CRC16=m -CONFIG_CRC32=m -CONFIG_LIBCRC32C=m +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +# CONFIG_CRC32 is not set +# CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=m -CONFIG_ZLIB_DEFLATE=m diff --git a/arch/mips/configs/tb0229_defconfig b/arch/mips/configs/tb0229_defconfig index be99261d799..5a924c1a580 100644 --- a/arch/mips/configs/tb0229_defconfig +++ b/arch/mips/configs/tb0229_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:35 2006 +# Linux kernel version: 2.6.17-rc2 +# Tue Apr 25 00:08:59 2006 # CONFIG_MIPS=y @@ -68,12 +68,14 @@ CONFIG_MACH_VR41XX=y # CONFIG_NEC_CMBVR4133 is not set CONFIG_TANBAC_TB022X=y # CONFIG_TANBAC_TB0226 is not set -CONFIG_TANBAC_TB0287=y +# CONFIG_TANBAC_TB0287 is not set # CONFIG_VICTOR_MPC30X is not set # CONFIG_ZAO_CAPCELLA is not set CONFIG_PCI_VR41XX=y # CONFIG_VRC4173 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -92,7 +94,7 @@ CONFIG_MIPS_L1_CACHE_SHIFT=5 # CONFIG_CPU_MIPS64_R2 is not set # CONFIG_CPU_R3000 is not set # CONFIG_CPU_TX39XX is not set -# CONFIG_CPU_VR41XX is not set +CONFIG_CPU_VR41XX=y # CONFIG_CPU_R4300 is not set # CONFIG_CPU_R4X00 is not set # CONFIG_CPU_TX49XX is not set @@ -105,18 +107,21 @@ CONFIG_MIPS_L1_CACHE_SHIFT=5 # CONFIG_CPU_RM7000 is not set # CONFIG_CPU_RM9000 is not set # CONFIG_CPU_SB1 is not set +CONFIG_SYS_HAS_CPU_VR41XX=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_64BIT_KERNEL=y # # Kernel type # -# CONFIG_32BIT is not set +CONFIG_32BIT=y # CONFIG_64BIT is not set CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_8KB is not set # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y @@ -137,7 +142,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -153,6 +157,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -166,10 +171,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -181,7 +182,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -189,6 +189,9 @@ CONFIG_KMOD=y # # Block layer # +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -208,7 +211,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -# CONFIG_PCI_LEGACY_PROC is not set CONFIG_MMU=y # @@ -226,6 +228,7 @@ CONFIG_MMU=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set +CONFIG_TRAD_SIGNALS=y # # Networking @@ -235,11 +238,10 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y -CONFIG_XFRM=y -CONFIG_XFRM_USER=m # CONFIG_NET_KEY is not set CONFIG_INET=y CONFIG_IP_MULTICAST=y @@ -264,12 +266,15 @@ CONFIG_SYN_COOKIES=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set CONFIG_INET_TUNNEL=m CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -281,6 +286,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -290,11 +300,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -311,10 +316,7 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_HAMRADIO is not set # CONFIG_IRDA is not set # CONFIG_BT is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m +# CONFIG_IEEE80211 is not set # # Device Drivers @@ -325,12 +327,12 @@ CONFIG_IEEE80211_CRYPT_CCMP=m # CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y -CONFIG_FW_LOADER=m +# CONFIG_FW_LOADER is not set # # Connector - unified userspace <-> kernelspace linker # -CONFIG_CONNECTOR=m +# CONFIG_CONNECTOR is not set # # Memory Technology Devices (MTD) @@ -363,10 +365,8 @@ CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=4096 # CONFIG_BLK_DEV_INITRD is not set -CONFIG_CDROM_PKTCDVD=m -CONFIG_CDROM_PKTCDVD_BUFFERS=8 -# CONFIG_CDROM_PKTCDVD_WCACHE is not set -CONFIG_ATA_OVER_ETH=m +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set # # ATA/ATAPI/MFM/RLL support @@ -443,30 +443,7 @@ CONFIG_MII=y # # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set -CONFIG_NET_PCI=y -# CONFIG_PCNET32 is not set -# CONFIG_AMD8111_ETH is not set -# CONFIG_ADAPTEC_STARFIRE is not set -# CONFIG_B44 is not set -# CONFIG_FORCEDETH is not set -# CONFIG_DGRS is not set -CONFIG_EEPRO100=y -# CONFIG_E100 is not set -# CONFIG_FEALNX is not set -# CONFIG_NATSEMI is not set -# CONFIG_NE2K_PCI is not set -# CONFIG_8139CP is not set -CONFIG_8139TOO=y -CONFIG_8139TOO_PIO=y -# CONFIG_8139TOO_TUNE_TWISTER is not set -# CONFIG_8139TOO_8129 is not set -# CONFIG_8139_OLD_RX_RESET is not set -# CONFIG_SIS900 is not set -# CONFIG_EPIC100 is not set -# CONFIG_SUNDANCE is not set -# CONFIG_TLAN is not set -# CONFIG_VIA_RHINE is not set -# CONFIG_LAN_SAA9730 is not set +# CONFIG_NET_PCI is not set # # Ethernet (1000 Mbit) @@ -483,7 +460,6 @@ CONFIG_R8169=y # CONFIG_SKGE is not set # CONFIG_SKY2 is not set # CONFIG_SK98LIN is not set -# CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -510,19 +486,8 @@ CONFIG_R8169=y # CONFIG_WAN is not set # CONFIG_FDDI is not set # CONFIG_HIPPI is not set -CONFIG_PPP=m -CONFIG_PPP_MULTILINK=y -CONFIG_PPP_FILTER=y -CONFIG_PPP_ASYNC=m -CONFIG_PPP_SYNC_TTY=m -CONFIG_PPP_DEFLATE=m -CONFIG_PPP_BSDCOMP=m -CONFIG_PPP_MPPE=m -CONFIG_PPPOE=m -CONFIG_SLIP=m -CONFIG_SLIP_COMPRESSED=y -CONFIG_SLIP_SMART=y -CONFIG_SLIP_MODE_SLIP6=y +# CONFIG_PPP is not set +# CONFIG_SLIP is not set # CONFIG_SHAPER is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set @@ -583,6 +548,11 @@ CONFIG_HW_CONSOLE=y # # Non-8250 serial port support # +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_SERIAL_VR41XX=y +CONFIG_SERIAL_VR41XX_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -607,6 +577,7 @@ CONFIG_TANBAC_TB0219=y # Ftape, the floppy tape device driver # # CONFIG_DRM is not set +CONFIG_GPIO_VR41XX=y # CONFIG_RAW_DRIVER is not set # @@ -642,10 +613,6 @@ CONFIG_TANBAC_TB0219=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -654,6 +621,7 @@ CONFIG_TANBAC_TB0219=y # Digital Video Broadcasting Devices # # CONFIG_DVB is not set +# CONFIG_USB_DABUSB is not set # # Graphics support @@ -676,6 +644,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=m # CONFIG_USB_DEBUG is not set @@ -731,9 +700,7 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y # CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set -# CONFIG_USB_MTOUCH is not set -# CONFIG_USB_ITMTOUCH is not set -# CONFIG_USB_EGALAX is not set +# CONFIG_USB_TOUCHSCREEN is not set # CONFIG_USB_YEALINK is not set # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set @@ -747,15 +714,6 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y # CONFIG_USB_MDC800 is not set # -# USB Multimedia devices -# -# CONFIG_USB_DABUSB is not set - -# -# Video4Linux support is needed for USB Multimedia device support -# - -# # USB Network Adapters # # CONFIG_USB_CATC is not set @@ -807,13 +765,48 @@ CONFIG_USB_MON=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock +# +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y + +# +# RTC drivers # +# CONFIG_RTC_DRV_M48T86 is not set +CONFIG_RTC_DRV_VR41XX=y +# CONFIG_RTC_DRV_TEST is not set # # File systems @@ -821,32 +814,16 @@ CONFIG_USB_MON=y CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XATTR is not set # CONFIG_EXT2_FS_XIP is not set -CONFIG_EXT3_FS=m -CONFIG_EXT3_FS_XATTR=y -# CONFIG_EXT3_FS_POSIX_ACL is not set -CONFIG_EXT3_FS_SECURITY=y -CONFIG_JBD=m -# CONFIG_JBD_DEBUG is not set -CONFIG_FS_MBCACHE=y +# CONFIG_EXT3_FS is not set # CONFIG_REISERFS_FS is not set -CONFIG_JFS_FS=m -# CONFIG_JFS_POSIX_ACL is not set -# CONFIG_JFS_SECURITY is not set -# CONFIG_JFS_DEBUG is not set -# CONFIG_JFS_STATISTICS is not set +# CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_XFS_FS=y -CONFIG_XFS_EXPORT=y -CONFIG_XFS_QUOTA=y -# CONFIG_XFS_SECURITY is not set -CONFIG_XFS_POSIX_ACL=y -# CONFIG_XFS_RT is not set +# CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_MINIX_FS is not set CONFIG_ROMFS_FS=m CONFIG_INOTIFY=y # CONFIG_QUOTA is not set -CONFIG_QUOTACTL=y CONFIG_DNOTIFY=y # CONFIG_AUTOFS_FS is not set CONFIG_AUTOFS4_FS=y @@ -855,20 +832,14 @@ CONFIG_FUSE_FS=m # # CD-ROM/DVD Filesystems # -CONFIG_ISO9660_FS=y -CONFIG_JOLIET=y -CONFIG_ZISOFS=y -CONFIG_ZISOFS_FS=y +# CONFIG_ISO9660_FS is not set # CONFIG_UDF_FS is not set # # DOS/FAT/NT Filesystems # -CONFIG_FAT_FS=m -CONFIG_MSDOS_FS=m -CONFIG_VFAT_FS=m -CONFIG_FAT_DEFAULT_CODEPAGE=437 -CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set # CONFIG_NTFS_FS is not set # @@ -880,7 +851,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -921,9 +891,7 @@ CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set -CONFIG_SMB_FS=m -CONFIG_SMB_NLS_DEFAULT=y -CONFIG_SMB_NLS_REMOTE="cp932" +# CONFIG_SMB_FS is not set # CONFIG_CIFS is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set @@ -939,46 +907,7 @@ CONFIG_MSDOS_PARTITION=y # # Native Language Support # -CONFIG_NLS=y -CONFIG_NLS_DEFAULT="iso8859-1" -CONFIG_NLS_CODEPAGE_437=m -# CONFIG_NLS_CODEPAGE_737 is not set -# CONFIG_NLS_CODEPAGE_775 is not set -# CONFIG_NLS_CODEPAGE_850 is not set -# CONFIG_NLS_CODEPAGE_852 is not set -# CONFIG_NLS_CODEPAGE_855 is not set -# CONFIG_NLS_CODEPAGE_857 is not set -# CONFIG_NLS_CODEPAGE_860 is not set -# CONFIG_NLS_CODEPAGE_861 is not set -# CONFIG_NLS_CODEPAGE_862 is not set -# CONFIG_NLS_CODEPAGE_863 is not set -# CONFIG_NLS_CODEPAGE_864 is not set -# CONFIG_NLS_CODEPAGE_865 is not set -# CONFIG_NLS_CODEPAGE_866 is not set -# CONFIG_NLS_CODEPAGE_869 is not set -# CONFIG_NLS_CODEPAGE_936 is not set -# CONFIG_NLS_CODEPAGE_950 is not set -CONFIG_NLS_CODEPAGE_932=m -# CONFIG_NLS_CODEPAGE_949 is not set -# CONFIG_NLS_CODEPAGE_874 is not set -# CONFIG_NLS_ISO8859_8 is not set -# CONFIG_NLS_CODEPAGE_1250 is not set -# CONFIG_NLS_CODEPAGE_1251 is not set -# CONFIG_NLS_ASCII is not set -CONFIG_NLS_ISO8859_1=m -# CONFIG_NLS_ISO8859_2 is not set -# CONFIG_NLS_ISO8859_3 is not set -# CONFIG_NLS_ISO8859_4 is not set -# CONFIG_NLS_ISO8859_5 is not set -# CONFIG_NLS_ISO8859_6 is not set -# CONFIG_NLS_ISO8859_7 is not set -# CONFIG_NLS_ISO8859_9 is not set -# CONFIG_NLS_ISO8859_13 is not set -# CONFIG_NLS_ISO8859_14 is not set -# CONFIG_NLS_ISO8859_15 is not set -# CONFIG_NLS_KOI8_R is not set -# CONFIG_NLS_KOI8_U is not set -# CONFIG_NLS_UTF8 is not set +# CONFIG_NLS is not set # # Profiling support @@ -992,44 +921,20 @@ CONFIG_NLS_ISO8859_1=m # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="mem=64M console=ttyVR0,115200 ip=any root=/dev/nfs" # # Security options # -CONFIG_KEYS=y -CONFIG_KEYS_DEBUG_PROC_KEYS=y +# CONFIG_KEYS is not set # CONFIG_SECURITY is not set # # Cryptographic options # -CONFIG_CRYPTO=y -CONFIG_CRYPTO_HMAC=y -CONFIG_CRYPTO_NULL=m -CONFIG_CRYPTO_MD4=m -CONFIG_CRYPTO_MD5=m -CONFIG_CRYPTO_SHA1=m -CONFIG_CRYPTO_SHA256=m -CONFIG_CRYPTO_SHA512=m -CONFIG_CRYPTO_WP512=m -CONFIG_CRYPTO_TGR192=m -CONFIG_CRYPTO_DES=m -CONFIG_CRYPTO_BLOWFISH=m -CONFIG_CRYPTO_TWOFISH=m -CONFIG_CRYPTO_SERPENT=m -CONFIG_CRYPTO_AES=m -CONFIG_CRYPTO_CAST5=m -CONFIG_CRYPTO_CAST6=m -CONFIG_CRYPTO_TEA=m -CONFIG_CRYPTO_ARC4=m -CONFIG_CRYPTO_KHAZAD=m -CONFIG_CRYPTO_ANUBIS=m -CONFIG_CRYPTO_DEFLATE=m -CONFIG_CRYPTO_MICHAEL_MIC=m -CONFIG_CRYPTO_CRC32C=m -# CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO is not set # # Hardware crypto devices @@ -1038,9 +943,8 @@ CONFIG_CRYPTO_CRC32C=m # # Library routines # -CONFIG_CRC_CCITT=m -CONFIG_CRC16=m +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set CONFIG_CRC32=y -CONFIG_LIBCRC32C=m -CONFIG_ZLIB_INFLATE=y -CONFIG_ZLIB_DEFLATE=m +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=m diff --git a/arch/mips/configs/tb0287_defconfig b/arch/mips/configs/tb0287_defconfig index 8a1e3ace0b2..9f215ea350d 100644 --- a/arch/mips/configs/tb0287_defconfig +++ b/arch/mips/configs/tb0287_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16 -# Wed Mar 22 11:07:34 2006 +# Linux kernel version: 2.6.17-rc2 +# Tue Apr 25 00:09:17 2006 # CONFIG_MIPS=y @@ -74,7 +74,10 @@ CONFIG_TANBAC_TB0287=y CONFIG_PCI_VR41XX=y # CONFIG_VRC4173 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y # CONFIG_CPU_BIG_ENDIAN is not set @@ -107,7 +110,6 @@ CONFIG_CPU_VR41XX=y # CONFIG_CPU_SB1 is not set CONFIG_SYS_HAS_CPU_VR41XX=y CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y -CONFIG_SYS_SUPPORTS_64BIT_KERNEL=y CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y CONFIG_CPU_SUPPORTS_64BIT_KERNEL=y @@ -121,7 +123,6 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y @@ -157,6 +158,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -170,10 +172,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -185,7 +183,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -194,6 +191,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -213,7 +212,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -# CONFIG_PCI_LEGACY_PROC is not set CONFIG_MMU=y # @@ -245,8 +243,6 @@ CONFIG_NET=y CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y -CONFIG_XFRM=y -CONFIG_XFRM_USER=m # CONFIG_NET_KEY is not set CONFIG_INET=y CONFIG_IP_MULTICAST=y @@ -271,6 +267,7 @@ CONFIG_SYN_COOKIES=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set CONFIG_INET_TUNNEL=m CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y @@ -288,6 +285,8 @@ CONFIG_TCP_CONG_HTCP=m # CONFIG_TCP_CONG_VEGAS is not set # CONFIG_TCP_CONG_SCALABLE is not set # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -493,7 +492,6 @@ CONFIG_BLK_DEV_SD=y # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set -# CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_QLOGIC_1280 is not set # CONFIG_SCSI_QLA_FC is not set # CONFIG_SCSI_LPFC is not set @@ -714,7 +712,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_WATCHDOG is not set # CONFIG_RTC is not set # CONFIG_GEN_RTC is not set -# CONFIG_RTC_VR41XX is not set # CONFIG_DTLK is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set @@ -760,10 +757,6 @@ CONFIG_GPIO_VR41XX=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -772,17 +765,53 @@ CONFIG_GPIO_VR41XX=y # Digital Video Broadcasting Devices # # CONFIG_DVB is not set +# CONFIG_USB_DABUSB is not set # # Graphics support # -# CONFIG_FB is not set +CONFIG_FB=y +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_MACMODES is not set +CONFIG_FB_FIRMWARE_EDID=y +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set +# CONFIG_FB_CIRRUS is not set +# CONFIG_FB_PM2 is not set +# CONFIG_FB_CYBER2000 is not set +# CONFIG_FB_ASILIANT is not set +# CONFIG_FB_IMSTT is not set +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_NVIDIA is not set +# CONFIG_FB_RIVA is not set +# CONFIG_FB_MATROX is not set +# CONFIG_FB_RADEON is not set +# CONFIG_FB_ATY128 is not set +# CONFIG_FB_ATY is not set +# CONFIG_FB_SAVAGE is not set +# CONFIG_FB_SIS is not set +# CONFIG_FB_NEOMAGIC is not set +# CONFIG_FB_KYRO is not set +# CONFIG_FB_3DFX is not set +# CONFIG_FB_VOODOO1 is not set +CONFIG_FB_SMIVGX=y +# CONFIG_FB_TRIDENT is not set +# CONFIG_FB_VIRTUAL is not set # # Console display driver support # # CONFIG_VGA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE is not set + +# +# Logo configuration +# +# CONFIG_LOGO is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Sound @@ -794,6 +823,7 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=m # CONFIG_USB_DEBUG is not set @@ -863,9 +893,7 @@ CONFIG_USB_HIDINPUT=y # CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set -# CONFIG_USB_MTOUCH is not set -# CONFIG_USB_ITMTOUCH is not set -# CONFIG_USB_EGALAX is not set +# CONFIG_USB_TOUCHSCREEN is not set # CONFIG_USB_YEALINK is not set # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set @@ -880,15 +908,6 @@ CONFIG_USB_HIDINPUT=y # CONFIG_USB_MICROTEK is not set # -# USB Multimedia devices -# -# CONFIG_USB_DABUSB is not set - -# -# Video4Linux support is needed for USB Multimedia device support -# - -# # USB Network Adapters # # CONFIG_USB_CATC is not set @@ -939,6 +958,19 @@ CONFIG_USB_MON=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set @@ -948,6 +980,11 @@ CONFIG_USB_MON=y # # +# Real Time Clock +# +# CONFIG_RTC_CLASS is not set + +# # File systems # CONFIG_EXT2_FS=y @@ -1001,7 +1038,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -# CONFIG_RELAYFS_FS is not set # CONFIG_CONFIGFS_FS is not set # @@ -1067,14 +1103,14 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="mem=64M console=ttyVR0,115200 ip=any root=/dev/nfs" # # Security options # -CONFIG_KEYS=y -CONFIG_KEYS_DEBUG_PROC_KEYS=y +# CONFIG_KEYS is not set # CONFIG_SECURITY is not set # diff --git a/arch/mips/configs/workpad_defconfig b/arch/mips/configs/workpad_defconfig index 7132e296d40..ac7765eb8da 100644 --- a/arch/mips/configs/workpad_defconfig +++ b/arch/mips/configs/workpad_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:36 2006 +# Linux kernel version: 2.6.17-rc2 +# Tue Apr 25 00:09:33 2006 # CONFIG_MIPS=y @@ -70,6 +70,8 @@ CONFIG_IBM_WORKPAD=y # CONFIG_VICTOR_MPC30X is not set # CONFIG_ZAO_CAPCELLA is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y @@ -88,7 +90,7 @@ CONFIG_MIPS_L1_CACHE_SHIFT=5 # CONFIG_CPU_MIPS64_R2 is not set # CONFIG_CPU_R3000 is not set # CONFIG_CPU_TX39XX is not set -# CONFIG_CPU_VR41XX is not set +CONFIG_CPU_VR41XX=y # CONFIG_CPU_R4300 is not set # CONFIG_CPU_R4X00 is not set # CONFIG_CPU_TX49XX is not set @@ -101,18 +103,21 @@ CONFIG_MIPS_L1_CACHE_SHIFT=5 # CONFIG_CPU_RM7000 is not set # CONFIG_CPU_RM9000 is not set # CONFIG_CPU_SB1 is not set +CONFIG_SYS_HAS_CPU_VR41XX=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_64BIT_KERNEL=y # # Kernel type # -# CONFIG_32BIT is not set +CONFIG_32BIT=y # CONFIG_64BIT is not set CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_8KB is not set # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set # CONFIG_MIPS_MT is not set -CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y @@ -133,7 +138,6 @@ CONFIG_PREEMPT_NONE=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -149,6 +153,7 @@ CONFIG_SYSVIPC=y CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -162,10 +167,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -177,7 +178,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -185,6 +185,9 @@ CONFIG_KMOD=y # # Block layer # +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -220,6 +223,7 @@ CONFIG_PCMCIA_IOCTL=y # CONFIG_I82365 is not set # CONFIG_TCIC is not set CONFIG_PCMCIA_PROBE=y +CONFIG_PCMCIA_VRC4171=y # # PCI Hotplug Support @@ -230,6 +234,7 @@ CONFIG_PCMCIA_PROBE=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set +CONFIG_TRAD_SIGNALS=y # # Networking @@ -239,6 +244,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -258,12 +264,15 @@ CONFIG_IP_FIB_HASH=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # @@ -275,6 +284,11 @@ CONFIG_TCP_CONG_BIC=y # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -284,11 +298,6 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -305,10 +314,8 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_HAMRADIO is not set # CONFIG_IRDA is not set # CONFIG_BT is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m +# CONFIG_IEEE80211 is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -347,10 +354,12 @@ CONFIG_CONNECTOR=m # CONFIG_BLK_DEV_COW_COMMON is not set # CONFIG_BLK_DEV_LOOP is not set # CONFIG_BLK_DEV_NBD is not set -# CONFIG_BLK_DEV_RAM is not set +CONFIG_BLK_DEV_RAM=m CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +# CONFIG_BLK_DEV_INITRD is not set # CONFIG_CDROM_PKTCDVD is not set -CONFIG_ATA_OVER_ETH=m +# CONFIG_ATA_OVER_ETH is not set # # ATA/ATAPI/MFM/RLL support @@ -468,7 +477,38 @@ CONFIG_MII=m # # Wireless LAN (non-hamradio) # -# CONFIG_NET_RADIO is not set +CONFIG_NET_RADIO=y +# CONFIG_NET_WIRELESS_RTNETLINK is not set + +# +# Obsolete Wireless cards support (pre-802.11) +# +# CONFIG_STRIP is not set +# CONFIG_ARLAN is not set +# CONFIG_WAVELAN is not set +# CONFIG_PCMCIA_WAVELAN is not set +# CONFIG_PCMCIA_NETWAVE is not set + +# +# Wireless 802.11 Frequency Hopping cards support +# +# CONFIG_PCMCIA_RAYCS is not set + +# +# Wireless 802.11b ISA/PCI cards support +# +CONFIG_HERMES=m +# CONFIG_ATMEL is not set + +# +# Wireless 802.11b Pcmcia/Cardbus cards support +# +CONFIG_PCMCIA_HERMES=m +# CONFIG_PCMCIA_SPECTRUM is not set +# CONFIG_AIRO_CS is not set +# CONFIG_PCMCIA_WL3501 is not set +# CONFIG_HOSTAP is not set +CONFIG_NET_WIRELESS=y # # PCMCIA network device support @@ -512,10 +552,7 @@ CONFIG_INPUT=y # # Userland interfaces # -CONFIG_INPUT_MOUSEDEV=y -CONFIG_INPUT_MOUSEDEV_PSAUX=y -CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 -CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set # CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set @@ -533,11 +570,7 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # # Hardware I/O ports # -CONFIG_SERIO=y -# CONFIG_SERIO_I8042 is not set -CONFIG_SERIO_SERPORT=y -# CONFIG_SERIO_LIBPS2 is not set -CONFIG_SERIO_RAW=m +# CONFIG_SERIO is not set # CONFIG_GAMEPORT is not set # @@ -556,6 +589,10 @@ CONFIG_HW_CONSOLE=y # # Non-8250 serial port support # +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_SERIAL_VR41XX=y +CONFIG_SERIAL_VR41XX_CONSOLE=y CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -568,20 +605,7 @@ CONFIG_LEGACY_PTY_COUNT=256 # # Watchdog Cards # -CONFIG_WATCHDOG=y -# CONFIG_WATCHDOG_NOWAYOUT is not set - -# -# Watchdog Device Drivers -# -# CONFIG_SOFT_WATCHDOG is not set - -# -# ISA-based Watchdog Cards -# -# CONFIG_PCWATCHDOG is not set -# CONFIG_MIXCOMWD is not set -# CONFIG_WDT is not set +# CONFIG_WATCHDOG is not set # CONFIG_RTC is not set # CONFIG_GEN_RTC is not set # CONFIG_DTLK is not set @@ -597,6 +621,7 @@ CONFIG_WATCHDOG=y # CONFIG_SYNCLINK_CS is not set # CONFIG_CARDMAN_4000 is not set # CONFIG_CARDMAN_4040 is not set +# CONFIG_GPIO_VR41XX is not set # CONFIG_RAW_DRIVER is not set # @@ -632,10 +657,6 @@ CONFIG_WATCHDOG=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -667,6 +688,7 @@ CONFIG_DUMMY_CONSOLE=y # # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -683,12 +705,30 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -710,7 +750,7 @@ CONFIG_FS_POSIX_ACL=y CONFIG_INOTIFY=y # CONFIG_QUOTA is not set CONFIG_DNOTIFY=y -CONFIG_AUTOFS_FS=y +# CONFIG_AUTOFS_FS is not set CONFIG_AUTOFS4_FS=y CONFIG_FUSE_FS=m @@ -733,10 +773,9 @@ CONFIG_FUSE_FS=m CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_SYSFS=y -# CONFIG_TMPFS is not set +CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -802,44 +841,20 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="console=ttyVR0,19200 mem=16M" # # Security options # -CONFIG_KEYS=y -CONFIG_KEYS_DEBUG_PROC_KEYS=y +# CONFIG_KEYS is not set # CONFIG_SECURITY is not set # # Cryptographic options # -CONFIG_CRYPTO=y -CONFIG_CRYPTO_HMAC=y -CONFIG_CRYPTO_NULL=m -CONFIG_CRYPTO_MD4=m -CONFIG_CRYPTO_MD5=m -CONFIG_CRYPTO_SHA1=m -CONFIG_CRYPTO_SHA256=m -CONFIG_CRYPTO_SHA512=m -CONFIG_CRYPTO_WP512=m -CONFIG_CRYPTO_TGR192=m -CONFIG_CRYPTO_DES=m -CONFIG_CRYPTO_BLOWFISH=m -CONFIG_CRYPTO_TWOFISH=m -CONFIG_CRYPTO_SERPENT=m -CONFIG_CRYPTO_AES=m -CONFIG_CRYPTO_CAST5=m -CONFIG_CRYPTO_CAST6=m -CONFIG_CRYPTO_TEA=m -CONFIG_CRYPTO_ARC4=m -CONFIG_CRYPTO_KHAZAD=m -CONFIG_CRYPTO_ANUBIS=m -CONFIG_CRYPTO_DEFLATE=m -CONFIG_CRYPTO_MICHAEL_MIC=m -CONFIG_CRYPTO_CRC32C=m -# CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO is not set # # Hardware crypto devices @@ -849,8 +864,6 @@ CONFIG_CRYPTO_CRC32C=m # Library routines # # CONFIG_CRC_CCITT is not set -CONFIG_CRC16=m +# CONFIG_CRC16 is not set CONFIG_CRC32=y -CONFIG_LIBCRC32C=m -CONFIG_ZLIB_INFLATE=m -CONFIG_ZLIB_DEFLATE=m +# CONFIG_LIBCRC32C is not set diff --git a/arch/mips/configs/yosemite_defconfig b/arch/mips/configs/yosemite_defconfig index 67457850941..b52d709de96 100644 --- a/arch/mips/configs/yosemite_defconfig +++ b/arch/mips/configs/yosemite_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:40:37 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:51:20 2006 # CONFIG_MIPS=y @@ -65,6 +65,8 @@ CONFIG_PMC_YOSEMITE=y # CONFIG_TOSHIBA_RBTX4938 is not set # CONFIG_HYPERTRANSPORT is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_DMA_COHERENT=y CONFIG_CPU_BIG_ENDIAN=y @@ -116,7 +118,6 @@ CONFIG_PAGE_SIZE_4KB=y CONFIG_CPU_HAS_PREFETCH=y # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -140,7 +141,6 @@ CONFIG_PREEMPT_BKL=y # Code maturity level options # # CONFIG_EXPERIMENTAL is not set -CONFIG_CLEAN_COMPILE=y CONFIG_LOCK_KERNEL=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -157,6 +157,7 @@ CONFIG_SYSCTL=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y # CONFIG_CPUSETS is not set +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" CONFIG_EMBEDDED=y CONFIG_KALLSYMS=y @@ -170,10 +171,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -184,7 +181,6 @@ CONFIG_BASE_SMALL=0 # CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y -CONFIG_OBSOLETE_MODPARM=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_KMOD=y @@ -194,6 +190,8 @@ CONFIG_STOP_MACHINE=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -213,7 +211,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y -CONFIG_PCI_LEGACY_PROC=y # CONFIG_PCI_DEBUG is not set CONFIG_MMU=y @@ -241,6 +238,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=m CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -261,16 +259,19 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set -CONFIG_INET_TUNNEL=m +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y +CONFIG_IPV6_ROUTER_PREF=y CONFIG_INET6_AH=m CONFIG_INET6_ESP=m CONFIG_INET6_IPCOMP=m +CONFIG_INET6_XFRM_TUNNEL=m CONFIG_INET6_TUNNEL=m CONFIG_IPV6_TUNNEL=m # CONFIG_NETFILTER is not set @@ -340,10 +341,9 @@ CONFIG_CONNECTOR=m # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 -# CONFIG_CDROM_PKTCDVD_WCACHE is not set CONFIG_ATA_OVER_ETH=m # @@ -433,6 +433,7 @@ CONFIG_MII=y # CONFIG_HAMACHI is not set # CONFIG_R8169 is not set # CONFIG_SIS190 is not set +# CONFIG_SKGE is not set # CONFIG_SK98LIN is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -497,6 +498,7 @@ CONFIG_TITAN_GE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -506,6 +508,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -563,10 +566,6 @@ CONFIG_GEN_RTC_X=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -591,6 +590,7 @@ CONFIG_GEN_RTC_X=y # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # @@ -608,12 +608,29 @@ CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # CONFIG_INFINIBAND is not set # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # # @@ -656,7 +673,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # # Miscellaneous filesystems diff --git a/arch/mips/defconfig b/arch/mips/defconfig index 42d5cd7927c..607e2985ffe 100644 --- a/arch/mips/defconfig +++ b/arch/mips/defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.16-rc1 -# Fri Jan 27 15:39:51 2006 +# Linux kernel version: 2.6.17-rc2 +# Mon Apr 24 14:50:54 2006 # CONFIG_MIPS=y @@ -64,6 +64,8 @@ CONFIG_SGI_IP22=y # CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4938 is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_ARC=y CONFIG_DMA_NONCOHERENT=y @@ -121,7 +123,6 @@ CONFIG_BOARD_SCACHE=y CONFIG_IP22_CPU_SCACHE=y # CONFIG_MIPS_MT is not set # CONFIG_64BIT_PHYS_ADDR is not set -# CONFIG_CPU_ADVANCED is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -143,7 +144,6 @@ CONFIG_PREEMPT_VOLUNTARY=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -160,6 +160,7 @@ CONFIG_SYSCTL=y # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y +CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EMBEDDED=y @@ -173,10 +174,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -188,7 +185,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y @@ -197,6 +193,8 @@ CONFIG_KMOD=y # Block layer # # CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -242,6 +240,7 @@ CONFIG_NET=y # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -264,6 +263,7 @@ CONFIG_IP_PNP_BOOTP=y CONFIG_INET_AH=m CONFIG_INET_ESP=m CONFIG_INET_IPCOMP=m +CONFIG_INET_XFRM_TUNNEL=m CONFIG_INET_TUNNEL=m CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y @@ -305,9 +305,12 @@ CONFIG_IP_VS_NQ=m CONFIG_IP_VS_FTP=m CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y +CONFIG_IPV6_ROUTER_PREF=y +CONFIG_IPV6_ROUTE_INFO=y CONFIG_INET6_AH=m CONFIG_INET6_ESP=m CONFIG_INET6_IPCOMP=m +CONFIG_INET6_XFRM_TUNNEL=m CONFIG_INET6_TUNNEL=m CONFIG_IPV6_TUNNEL=m CONFIG_NETFILTER=y @@ -330,11 +333,14 @@ CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m CONFIG_NETFILTER_XT_MATCH_CONNMARK=m CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m +CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m @@ -357,20 +363,19 @@ CONFIG_IP_NF_IRC=m CONFIG_IP_NF_TFTP=m CONFIG_IP_NF_AMANDA=m CONFIG_IP_NF_PPTP=m +CONFIG_IP_NF_H323=m CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_IPRANGE=m -CONFIG_IP_NF_MATCH_MULTIPORT=m CONFIG_IP_NF_MATCH_TOS=m CONFIG_IP_NF_MATCH_RECENT=m CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_DSCP=m -CONFIG_IP_NF_MATCH_AH_ESP=m +CONFIG_IP_NF_MATCH_AH=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_MATCH_OWNER=m CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_HASHLIMIT=m -CONFIG_IP_NF_MATCH_POLICY=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -388,6 +393,7 @@ CONFIG_IP_NF_NAT_FTP=m CONFIG_IP_NF_NAT_TFTP=m CONFIG_IP_NF_NAT_AMANDA=m CONFIG_IP_NF_NAT_PPTP=m +CONFIG_IP_NF_NAT_H323=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_TOS=m CONFIG_IP_NF_TARGET_ECN=m @@ -408,12 +414,10 @@ CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_FRAG=m CONFIG_IP6_NF_MATCH_HL=m -CONFIG_IP6_NF_MATCH_MULTIPORT=m CONFIG_IP6_NF_MATCH_OWNER=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AHESP=m +CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_MATCH_POLICY=m CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_LOG=m CONFIG_IP6_NF_TARGET_REJECT=m @@ -435,6 +439,11 @@ CONFIG_IP_SCTP=m # CONFIG_SCTP_HMAC_NONE is not set # CONFIG_SCTP_HMAC_SHA1 is not set CONFIG_SCTP_HMAC_MD5=y + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -444,11 +453,6 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set CONFIG_NET_DIVERT=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -508,6 +512,9 @@ CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set +CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -546,7 +553,7 @@ CONFIG_CONNECTOR=m # CONFIG_BLK_DEV_LOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 +# CONFIG_BLK_DEV_INITRD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set @@ -812,10 +819,6 @@ CONFIG_MAX_RAW_DEVS=256 # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -857,6 +860,7 @@ CONFIG_LOGO_SGI_CLUT224=y # # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -873,12 +877,30 @@ CONFIG_LOGO_SGI_CLUT224=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # # -# SN Devices +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock # +# CONFIG_RTC_CLASS is not set # # File systems @@ -944,7 +966,6 @@ CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y -CONFIG_RELAYFS_FS=m # CONFIG_CONFIGFS_FS is not set # @@ -963,7 +984,6 @@ CONFIG_EFS_FS=m # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set CONFIG_UFS_FS=m -# CONFIG_UFS_FS_WRITE is not set # # Network File Systems @@ -1078,6 +1098,7 @@ CONFIG_NLS_UTF8=m # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set CONFIG_CROSSCOMPILE=y CONFIG_CMDLINE="" diff --git a/arch/mips/kernel/branch.c b/arch/mips/kernel/branch.c index 374de839558..b6232d9033c 100644 --- a/arch/mips/kernel/branch.c +++ b/arch/mips/kernel/branch.c @@ -184,7 +184,7 @@ int __compute_return_epc(struct pt_regs *regs) bit = (insn.i_format.rt >> 2); bit += (bit != 0); bit += 23; - switch (insn.i_format.rt) { + switch (insn.i_format.rt & 3) { case 0: /* bc1f */ case 2: /* bc1fl */ if (~fcr31 & (1 << bit)) diff --git a/arch/mips/kernel/ptrace.c b/arch/mips/kernel/ptrace.c index f3106d0771b..9b4733c1239 100644 --- a/arch/mips/kernel/ptrace.c +++ b/arch/mips/kernel/ptrace.c @@ -483,7 +483,7 @@ static inline int audit_arch(void) asmlinkage void do_syscall_trace(struct pt_regs *regs, int entryexit) { if (unlikely(current->audit_context) && entryexit) - audit_syscall_exit(current, AUDITSC_RESULT(regs->regs[2]), + audit_syscall_exit(AUDITSC_RESULT(regs->regs[2]), regs->regs[2]); if (!(current->ptrace & PT_PTRACED)) @@ -507,7 +507,7 @@ asmlinkage void do_syscall_trace(struct pt_regs *regs, int entryexit) } out: if (unlikely(current->audit_context) && !entryexit) - audit_syscall_entry(current, audit_arch(), regs->regs[2], + audit_syscall_entry(audit_arch(), regs->regs[2], regs->regs[4], regs->regs[5], regs->regs[6], regs->regs[7]); } diff --git a/arch/mips/kernel/rtlx.c b/arch/mips/kernel/rtlx.c index 6179805af9f..caf777f8328 100644 --- a/arch/mips/kernel/rtlx.c +++ b/arch/mips/kernel/rtlx.c @@ -398,15 +398,14 @@ ssize_t rtlx_write(int index, void *buffer, size_t count, int user) static int file_open(struct inode *inode, struct file *filp) { - int minor = MINOR(inode->i_rdev); + int minor = iminor(inode); return rtlx_open(minor, (filp->f_flags & O_NONBLOCK) ? 0 : 1); } static int file_release(struct inode *inode, struct file *filp) { - int minor; - minor = MINOR(inode->i_rdev); + int minor = iminor(inode); return rtlx_release(minor); } @@ -416,7 +415,7 @@ static unsigned int file_poll(struct file *file, poll_table * wait) int minor; unsigned int mask = 0; - minor = MINOR(file->f_dentry->d_inode->i_rdev); + minor = iminor(file->f_dentry->d_inode); poll_wait(file, &channel_wqs[minor].rt_queue, wait); poll_wait(file, &channel_wqs[minor].lx_queue, wait); @@ -438,7 +437,7 @@ static unsigned int file_poll(struct file *file, poll_table * wait) static ssize_t file_read(struct file *file, char __user * buffer, size_t count, loff_t * ppos) { - int minor = MINOR(file->f_dentry->d_inode->i_rdev); + int minor = iminor(file->f_dentry->d_inode); /* data available? */ if (!rtlx_read_poll(minor, (file->f_flags & O_NONBLOCK) ? 0 : 1)) { @@ -455,7 +454,7 @@ static ssize_t file_write(struct file *file, const char __user * buffer, struct rtlx_channel *rt; DECLARE_WAITQUEUE(wait, current); - minor = MINOR(file->f_dentry->d_inode->i_rdev); + minor = iminor(file->f_dentry->d_inode); rt = &rtlx->channel[minor]; /* any space left... */ diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c index 80ffaa6d50a..85d7df7b18e 100644 --- a/arch/mips/kernel/vpe.c +++ b/arch/mips/kernel/vpe.c @@ -1072,7 +1072,7 @@ static int vpe_open(struct inode *inode, struct file *filp) struct vpe_notifications *not; /* assume only 1 device at the mo. */ - if ((minor = MINOR(inode->i_rdev)) != 1) { + if ((minor = iminor(inode)) != 1) { printk(KERN_WARNING "VPE loader: only vpe1 is supported\n"); return -ENODEV; } @@ -1133,7 +1133,7 @@ static int vpe_release(struct inode *inode, struct file *filp) struct vpe *v; Elf_Ehdr *hdr; - minor = MINOR(inode->i_rdev); + minor = iminor(inode); if ((v = get_vpe(minor)) == NULL) return -ENODEV; @@ -1174,7 +1174,7 @@ static ssize_t vpe_write(struct file *file, const char __user * buffer, size_t ret = count; struct vpe *v; - minor = MINOR(file->f_dentry->d_inode->i_rdev); + minor = iminor(file->f_dentry->d_inode); if ((v = get_vpe(minor)) == NULL) return -ENODEV; diff --git a/arch/mips/mips-boards/generic/init.c b/arch/mips/mips-boards/generic/init.c index 17dfe6a8cab..df4e9473560 100644 --- a/arch/mips/mips-boards/generic/init.c +++ b/arch/mips/mips-boards/generic/init.c @@ -337,6 +337,7 @@ void __init prom_init(void) case MIPS_REVISION_CORID_CORE_MSC: case MIPS_REVISION_CORID_CORE_FPGA2: case MIPS_REVISION_CORID_CORE_FPGA3: + case MIPS_REVISION_CORID_CORE_24K: case MIPS_REVISION_CORID_CORE_EMUL_MSC: _pcictrl_msc = (unsigned long)ioremap(MIPS_MSC01_PCI_REG_BASE, 0x2000); diff --git a/arch/mips/mips-boards/generic/pci.c b/arch/mips/mips-boards/generic/pci.c index 1f6f9df74ab..9337f6c8873 100644 --- a/arch/mips/mips-boards/generic/pci.c +++ b/arch/mips/mips-boards/generic/pci.c @@ -198,6 +198,7 @@ void __init mips_pcibios_init(void) case MIPS_REVISION_CORID_CORE_MSC: case MIPS_REVISION_CORID_CORE_FPGA2: case MIPS_REVISION_CORID_CORE_FPGA3: + case MIPS_REVISION_CORID_CORE_24K: case MIPS_REVISION_CORID_CORE_EMUL_MSC: /* Set up resource ranges from the controller's registers. */ MSC_READ(MSC01_PCI_SC2PMBASL, start); diff --git a/arch/mips/mips-boards/malta/malta_int.c b/arch/mips/mips-boards/malta/malta_int.c index 64db07d4dbe..7cc0ba4f553 100644 --- a/arch/mips/mips-boards/malta/malta_int.c +++ b/arch/mips/mips-boards/malta/malta_int.c @@ -57,6 +57,7 @@ static inline int mips_pcibios_iack(void) case MIPS_REVISION_CORID_CORE_MSC: case MIPS_REVISION_CORID_CORE_FPGA2: case MIPS_REVISION_CORID_CORE_FPGA3: + case MIPS_REVISION_CORID_CORE_24K: case MIPS_REVISION_CORID_CORE_EMUL_MSC: MSC_READ(MSC01_PCI_IACK, irq); irq &= 0xff; @@ -143,6 +144,7 @@ void corehi_irqdispatch(struct pt_regs *regs) case MIPS_REVISION_CORID_CORE_MSC: case MIPS_REVISION_CORID_CORE_FPGA2: case MIPS_REVISION_CORID_CORE_FPGA3: + case MIPS_REVISION_CORID_CORE_24K: case MIPS_REVISION_CORID_CORE_EMUL_MSC: ll_msc_irq(regs); break; @@ -309,6 +311,7 @@ void __init arch_init_irq(void) case MIPS_REVISION_CORID_CORE_MSC: case MIPS_REVISION_CORID_CORE_FPGA2: case MIPS_REVISION_CORID_CORE_FPGA3: + case MIPS_REVISION_CORID_CORE_24K: case MIPS_REVISION_CORID_CORE_EMUL_MSC: if (cpu_has_veic) init_msc_irqs (MSC01E_INT_BASE, msc_eicirqmap, msc_nr_eicirqs); diff --git a/arch/mips/oprofile/common.c b/arch/mips/oprofile/common.c index 935dd851f48..f2b4862aaae 100644 --- a/arch/mips/oprofile/common.c +++ b/arch/mips/oprofile/common.c @@ -27,7 +27,7 @@ static int op_mips_setup(void) model->reg_setup(ctr); /* Configure the registers on all cpus. */ - on_each_cpu(model->cpu_setup, 0, 0, 1); + on_each_cpu(model->cpu_setup, NULL, 0, 1); return 0; } @@ -114,5 +114,6 @@ int __init oprofile_arch_init(struct oprofile_operations *ops) void oprofile_arch_exit(void) { - model->exit(); + if (model) + model->exit(); } diff --git a/arch/mips/sgi-ip27/ip27-timer.c b/arch/mips/sgi-ip27/ip27-timer.c index cddf1cedf00..36b662e27b6 100644 --- a/arch/mips/sgi-ip27/ip27-timer.c +++ b/arch/mips/sgi-ip27/ip27-timer.c @@ -122,7 +122,7 @@ again: xtime.tv_sec > last_rtc_update + 660 && (xtime.tv_nsec / 1000) >= 500000 - ((unsigned) TICK_SIZE) / 2 && (xtime.tv_nsec / 1000) <= 500000 + ((unsigned) TICK_SIZE) / 2) { - if (rtc_set_time(xtime.tv_sec) == 0) { + if (rtc_mips_set_time(xtime.tv_sec) == 0) { last_rtc_update = xtime.tv_sec; } else { last_rtc_update = xtime.tv_sec - 600; diff --git a/arch/mips/sgi-ip32/ip32-irq.c b/arch/mips/sgi-ip32/ip32-irq.c index 22a6df94b4a..de01c9815bd 100644 --- a/arch/mips/sgi-ip32/ip32-irq.c +++ b/arch/mips/sgi-ip32/ip32-irq.c @@ -507,13 +507,14 @@ static void ip32_irq0(struct pt_regs *regs) int irq = 0; crime_int = crime->istat & crime_mask; - irq = ffs(crime_int); - crime_int = 1 << (irq - 1); + irq = __ffs(crime_int); + crime_int = 1 << irq; if (crime_int & CRIME_MACEISA_INT_MASK) { unsigned long mace_int = mace->perif.ctrl.istat; - irq = ffs(mace_int & maceisa_mask) + 32; + irq = __ffs(mace_int & maceisa_mask) + 32; } + irq++; DBG("*irq %u*\n", irq); do_IRQ(irq, regs); } diff --git a/arch/powerpc/configs/cell_defconfig b/arch/powerpc/configs/cell_defconfig index fe22e54ab2b..dbe421dc3c1 100644 --- a/arch/powerpc/configs/cell_defconfig +++ b/arch/powerpc/configs/cell_defconfig @@ -9,6 +9,7 @@ CONFIG_PPC_MERGE=y CONFIG_MMU=y CONFIG_GENERIC_HARDIRQS=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_PPC=y CONFIG_EARLY_PRINTK=y @@ -55,6 +56,7 @@ CONFIG_SYSCTL=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y # CONFIG_CPUSETS is not set +# CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" CONFIG_CC_OPTIMIZE_FOR_SIZE=y # CONFIG_EMBEDDED is not set @@ -69,10 +71,6 @@ CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 @@ -84,7 +82,6 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_KMOD=y @@ -93,6 +90,7 @@ CONFIG_STOP_MACHINE=y # # Block layer # +# CONFIG_BLK_DEV_IO_TRACE is not set # # IO Schedulers @@ -126,6 +124,7 @@ CONFIG_RTAS_FLASH=y CONFIG_MMIO_NVRAM=y CONFIG_CELL_IIC=y # CONFIG_PPC_MPC106 is not set +# CONFIG_PPC_970_NAP is not set # CONFIG_CPU_FREQ is not set # CONFIG_WANT_EARLY_SERIAL is not set @@ -167,7 +166,6 @@ CONFIG_HAVE_MEMORY_PRESENT=y CONFIG_SPARSEMEM_EXTREME=y # CONFIG_MEMORY_HOTPLUG is not set CONFIG_SPLIT_PTLOCK_CPUS=4 -CONFIG_MIGRATION=y # CONFIG_PPC_64K_PAGES is not set CONFIG_SCHED_SMT=y CONFIG_PROC_DEVICETREE=y @@ -184,7 +182,6 @@ CONFIG_GENERIC_ISA_DMA=y # CONFIG_PPC_INDIRECT_PCI is not set CONFIG_PCI=y CONFIG_PCI_DOMAINS=y -CONFIG_PCI_LEGACY_PROC=y # CONFIG_PCI_DEBUG is not set # @@ -226,6 +223,7 @@ CONFIG_SYN_COOKIES=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set CONFIG_INET_TUNNEL=y CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y @@ -242,6 +240,7 @@ CONFIG_IPV6=y CONFIG_INET6_AH=m CONFIG_INET6_ESP=m CONFIG_INET6_IPCOMP=m +CONFIG_INET6_XFRM_TUNNEL=m CONFIG_INET6_TUNNEL=m CONFIG_IPV6_TUNNEL=m CONFIG_NETFILTER=y @@ -632,6 +631,7 @@ CONFIG_SERIAL_NONSTANDARD=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -717,7 +717,6 @@ CONFIG_I2C_ALGOBIT=y # CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_PROSAVAGE is not set # CONFIG_I2C_SAVAGE4 is not set -# CONFIG_SCx200_ACB is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set # CONFIG_I2C_SIS96X is not set @@ -736,9 +735,7 @@ CONFIG_I2C_ALGOBIT=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set -# CONFIG_SENSORS_RTC8564 is not set # CONFIG_SENSORS_MAX6875 is not set -# CONFIG_RTC_X1205_I2C is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set @@ -766,10 +763,6 @@ CONFIG_I2C_ALGOBIT=y # # -# Multimedia Capabilities Port drivers -# - -# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -818,6 +811,19 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_MMC is not set # +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# # InfiniBand support # CONFIG_INFINIBAND=y @@ -834,6 +840,11 @@ CONFIG_INFINIBAND_IPOIB_DEBUG_DATA=y # # +# Real Time Clock +# +# CONFIG_RTC_CLASS is not set + +# # File systems # CONFIG_EXT2_FS=y @@ -889,7 +900,6 @@ CONFIG_TMPFS=y CONFIG_HUGETLBFS=y CONFIG_HUGETLB_PAGE=y CONFIG_RAMFS=y -# CONFIG_RELAYFS_FS is not set # CONFIG_CONFIGFS_FS is not set # diff --git a/arch/powerpc/kernel/cputable.c b/arch/powerpc/kernel/cputable.c index 39e348a3ade..3f7182db9ed 100644 --- a/arch/powerpc/kernel/cputable.c +++ b/arch/powerpc/kernel/cputable.c @@ -57,6 +57,8 @@ extern void __setup_cpu_ppc970(unsigned long offset, struct cpu_spec* spec); PPC_FEATURE_SMT | PPC_FEATURE_ICACHE_SNOOP) #define COMMON_USER_POWER5_PLUS (COMMON_USER_PPC64 | PPC_FEATURE_POWER5_PLUS|\ PPC_FEATURE_SMT | PPC_FEATURE_ICACHE_SNOOP) +#define COMMON_USER_POWER6 (COMMON_USER_PPC64 | PPC_FEATURE_ARCH_2_05 |\ + PPC_FEATURE_SMT | PPC_FEATURE_ICACHE_SNOOP) #define COMMON_USER_BOOKE (PPC_FEATURE_32 | PPC_FEATURE_HAS_MMU | \ PPC_FEATURE_BOOKE) @@ -263,6 +265,20 @@ struct cpu_spec cpu_specs[] = { .oprofile_type = PPC_OPROFILE_POWER4, .platform = "power5+", }, + { /* Power6 */ + .pvr_mask = 0xffff0000, + .pvr_value = 0x003e0000, + .cpu_name = "POWER6", + .cpu_features = CPU_FTRS_POWER6, + .cpu_user_features = COMMON_USER_POWER6, + .icache_bsize = 128, + .dcache_bsize = 128, + .num_pmcs = 6, + .cpu_setup = __setup_cpu_power4, + .oprofile_cpu_type = "ppc64/power6", + .oprofile_type = PPC_OPROFILE_POWER4, + .platform = "power6", + }, { /* Cell Broadband Engine */ .pvr_mask = 0xffff0000, .pvr_value = 0x00700000, diff --git a/arch/powerpc/kernel/kprobes.c b/arch/powerpc/kernel/kprobes.c index 856ef1a832b..f78866367b7 100644 --- a/arch/powerpc/kernel/kprobes.c +++ b/arch/powerpc/kernel/kprobes.c @@ -90,15 +90,15 @@ void __kprobes arch_remove_kprobe(struct kprobe *p) static void __kprobes prepare_singlestep(struct kprobe *p, struct pt_regs *regs) { - kprobe_opcode_t insn = *p->ainsn.insn; - regs->msr |= MSR_SE; - /* single step inline if it is a trap variant */ - if (is_trap(insn)) - regs->nip = (unsigned long)p->addr; - else - regs->nip = (unsigned long)p->ainsn.insn; + /* + * On powerpc we should single step on the original + * instruction even if the probed insn is a trap + * variant as values in regs could play a part in + * if the trap is taken or not + */ + regs->nip = (unsigned long)p->ainsn.insn; } static void __kprobes save_previous_kprobe(struct kprobe_ctlblk *kcb) diff --git a/arch/powerpc/kernel/module_64.c b/arch/powerpc/kernel/module_64.c index 928b8581fcb..ba34001fca8 100644 --- a/arch/powerpc/kernel/module_64.c +++ b/arch/powerpc/kernel/module_64.c @@ -191,11 +191,19 @@ int module_frob_arch_sections(Elf64_Ehdr *hdr, (void *)hdr + sechdrs[sechdrs[i].sh_link].sh_offset); } - if (!me->arch.stubs_section || !me->arch.toc_section) { - printk("%s: doesn't contain .toc or .stubs.\n", me->name); + + if (!me->arch.stubs_section) { + printk("%s: doesn't contain .stubs.\n", me->name); return -ENOEXEC; } + /* If we don't have a .toc, just use .stubs. We need to set r2 + to some reasonable value in case the module calls out to + other functions via a stub, or if a function pointer escapes + the module by some means. */ + if (!me->arch.toc_section) + me->arch.toc_section = me->arch.stubs_section; + /* Override the stubs size */ sechdrs[me->arch.stubs_section].sh_size = get_stubs_size(hdr, sechdrs); return 0; @@ -342,7 +350,7 @@ int apply_relocate_add(Elf64_Shdr *sechdrs, break; case R_PPC64_TOC16: - /* Subtact TOC pointer */ + /* Subtract TOC pointer */ value -= my_r2(sechdrs, me); if (value + 0x8000 > 0xffff) { printk("%s: bad TOC16 relocation (%lu)\n", @@ -355,7 +363,7 @@ int apply_relocate_add(Elf64_Shdr *sechdrs, break; case R_PPC64_TOC16_DS: - /* Subtact TOC pointer */ + /* Subtract TOC pointer */ value -= my_r2(sechdrs, me); if ((value & 3) != 0 || value + 0x8000 > 0xffff) { printk("%s: bad TOC16_DS relocation (%lu)\n", diff --git a/arch/powerpc/kernel/prom.c b/arch/powerpc/kernel/prom.c index 1cb69e8fb0b..9a07f97f071 100644 --- a/arch/powerpc/kernel/prom.c +++ b/arch/powerpc/kernel/prom.c @@ -885,6 +885,74 @@ void __init unflatten_device_tree(void) DBG(" <- unflatten_device_tree()\n"); } +/* + * ibm,pa-features is a per-cpu property that contains a string of + * attribute descriptors, each of which has a 2 byte header plus up + * to 254 bytes worth of processor attribute bits. First header + * byte specifies the number of bytes following the header. + * Second header byte is an "attribute-specifier" type, of which + * zero is the only currently-defined value. + * Implementation: Pass in the byte and bit offset for the feature + * that we are interested in. The function will return -1 if the + * pa-features property is missing, or a 1/0 to indicate if the feature + * is supported/not supported. Note that the bit numbers are + * big-endian to match the definition in PAPR. + */ +static struct ibm_pa_feature { + unsigned long cpu_features; /* CPU_FTR_xxx bit */ + unsigned int cpu_user_ftrs; /* PPC_FEATURE_xxx bit */ + unsigned char pabyte; /* byte number in ibm,pa-features */ + unsigned char pabit; /* bit number (big-endian) */ + unsigned char invert; /* if 1, pa bit set => clear feature */ +} ibm_pa_features[] __initdata = { + {0, PPC_FEATURE_HAS_MMU, 0, 0, 0}, + {0, PPC_FEATURE_HAS_FPU, 0, 1, 0}, + {CPU_FTR_SLB, 0, 0, 2, 0}, + {CPU_FTR_CTRL, 0, 0, 3, 0}, + {CPU_FTR_NOEXECUTE, 0, 0, 6, 0}, + {CPU_FTR_NODSISRALIGN, 0, 1, 1, 1}, + {CPU_FTR_CI_LARGE_PAGE, 0, 1, 2, 0}, +}; + +static void __init check_cpu_pa_features(unsigned long node) +{ + unsigned char *pa_ftrs; + unsigned long len, tablelen, i, bit; + + pa_ftrs = of_get_flat_dt_prop(node, "ibm,pa-features", &tablelen); + if (pa_ftrs == NULL) + return; + + /* find descriptor with type == 0 */ + for (;;) { + if (tablelen < 3) + return; + len = 2 + pa_ftrs[0]; + if (tablelen < len) + return; /* descriptor 0 not found */ + if (pa_ftrs[1] == 0) + break; + tablelen -= len; + pa_ftrs += len; + } + + /* loop over bits we know about */ + for (i = 0; i < ARRAY_SIZE(ibm_pa_features); ++i) { + struct ibm_pa_feature *fp = &ibm_pa_features[i]; + + if (fp->pabyte >= pa_ftrs[0]) + continue; + bit = (pa_ftrs[2 + fp->pabyte] >> (7 - fp->pabit)) & 1; + if (bit ^ fp->invert) { + cur_cpu_spec->cpu_features |= fp->cpu_features; + cur_cpu_spec->cpu_user_features |= fp->cpu_user_ftrs; + } else { + cur_cpu_spec->cpu_features &= ~fp->cpu_features; + cur_cpu_spec->cpu_user_features &= ~fp->cpu_user_ftrs; + } + } +} + static int __init early_init_dt_scan_cpus(unsigned long node, const char *uname, int depth, void *data) @@ -969,6 +1037,8 @@ static int __init early_init_dt_scan_cpus(unsigned long node, } #endif /* CONFIG_ALTIVEC */ + check_cpu_pa_features(node); + #ifdef CONFIG_PPC_PSERIES if (nthreads > 1) cur_cpu_spec->cpu_features |= CPU_FTR_SMT; diff --git a/arch/powerpc/kernel/prom_init.c b/arch/powerpc/kernel/prom_init.c index 7e4d54821a0..078fb553354 100644 --- a/arch/powerpc/kernel/prom_init.c +++ b/arch/powerpc/kernel/prom_init.c @@ -636,10 +636,96 @@ static void __init early_cmdline_parse(void) #ifdef CONFIG_PPC_PSERIES /* - * To tell the firmware what our capabilities are, we have to pass - * it a fake 32-bit ELF header containing a couple of PT_NOTE sections - * that contain structures that contain the actual values. + * There are two methods for telling firmware what our capabilities are. + * Newer machines have an "ibm,client-architecture-support" method on the + * root node. For older machines, we have to call the "process-elf-header" + * method in the /packages/elf-loader node, passing it a fake 32-bit + * ELF header containing a couple of PT_NOTE sections that contain + * structures that contain various information. */ + +/* + * New method - extensible architecture description vector. + * + * Because the description vector contains a mix of byte and word + * values, we declare it as an unsigned char array, and use this + * macro to put word values in. + */ +#define W(x) ((x) >> 24) & 0xff, ((x) >> 16) & 0xff, \ + ((x) >> 8) & 0xff, (x) & 0xff + +/* Option vector bits - generic bits in byte 1 */ +#define OV_IGNORE 0x80 /* ignore this vector */ +#define OV_CESSATION_POLICY 0x40 /* halt if unsupported option present*/ + +/* Option vector 1: processor architectures supported */ +#define OV1_PPC_2_00 0x80 /* set if we support PowerPC 2.00 */ +#define OV1_PPC_2_01 0x40 /* set if we support PowerPC 2.01 */ +#define OV1_PPC_2_02 0x20 /* set if we support PowerPC 2.02 */ +#define OV1_PPC_2_03 0x10 /* set if we support PowerPC 2.03 */ +#define OV1_PPC_2_04 0x08 /* set if we support PowerPC 2.04 */ +#define OV1_PPC_2_05 0x04 /* set if we support PowerPC 2.05 */ + +/* Option vector 2: Open Firmware options supported */ +#define OV2_REAL_MODE 0x20 /* set if we want OF in real mode */ + +/* Option vector 3: processor options supported */ +#define OV3_FP 0x80 /* floating point */ +#define OV3_VMX 0x40 /* VMX/Altivec */ + +/* Option vector 5: PAPR/OF options supported */ +#define OV5_LPAR 0x80 /* logical partitioning supported */ +#define OV5_SPLPAR 0x40 /* shared-processor LPAR supported */ +/* ibm,dynamic-reconfiguration-memory property supported */ +#define OV5_DRCONF_MEMORY 0x20 +#define OV5_LARGE_PAGES 0x10 /* large pages supported */ + +/* + * The architecture vector has an array of PVR mask/value pairs, + * followed by # option vectors - 1, followed by the option vectors. + */ +static unsigned char ibm_architecture_vec[] = { + W(0xfffe0000), W(0x003a0000), /* POWER5/POWER5+ */ + W(0xffff0000), W(0x003e0000), /* POWER6 */ + W(0xfffffffe), W(0x0f000001), /* all 2.04-compliant and earlier */ + 5 - 1, /* 5 option vectors */ + + /* option vector 1: processor architectures supported */ + 3 - 1, /* length */ + 0, /* don't ignore, don't halt */ + OV1_PPC_2_00 | OV1_PPC_2_01 | OV1_PPC_2_02 | OV1_PPC_2_03 | + OV1_PPC_2_04 | OV1_PPC_2_05, + + /* option vector 2: Open Firmware options supported */ + 34 - 1, /* length */ + OV2_REAL_MODE, + 0, 0, + W(0xffffffff), /* real_base */ + W(0xffffffff), /* real_size */ + W(0xffffffff), /* virt_base */ + W(0xffffffff), /* virt_size */ + W(0xffffffff), /* load_base */ + W(64), /* 128MB min RMA */ + W(0xffffffff), /* full client load */ + 0, /* min RMA percentage of total RAM */ + 48, /* max log_2(hash table size) */ + + /* option vector 3: processor options supported */ + 3 - 1, /* length */ + 0, /* don't ignore, don't halt */ + OV3_FP | OV3_VMX, + + /* option vector 4: IBM PAPR implementation */ + 2 - 1, /* length */ + 0, /* don't halt */ + + /* option vector 5: PAPR/OF options */ + 3 - 1, /* length */ + 0, /* don't ignore, don't halt */ + OV5_LPAR | OV5_SPLPAR | OV5_LARGE_PAGES, +}; + +/* Old method - ELF header with PT_NOTE sections */ static struct fake_elf { Elf32_Ehdr elfhdr; Elf32_Phdr phdr[2]; @@ -728,8 +814,26 @@ static struct fake_elf { static void __init prom_send_capabilities(void) { - ihandle elfloader; + ihandle elfloader, root; + prom_arg_t ret; + + root = call_prom("open", 1, 1, ADDR("/")); + if (root != 0) { + /* try calling the ibm,client-architecture-support method */ + if (call_prom_ret("call-method", 3, 2, &ret, + ADDR("ibm,client-architecture-support"), + ADDR(ibm_architecture_vec)) == 0) { + /* the call exists... */ + if (ret) + prom_printf("WARNING: ibm,client-architecture" + "-support call FAILED!\n"); + call_prom("close", 1, 0, root); + return; + } + call_prom("close", 1, 0, root); + } + /* no ibm,client-architecture-support call, try the old way */ elfloader = call_prom("open", 1, 1, ADDR("/packages/elf-loader")); if (elfloader == 0) { prom_printf("couldn't open /packages/elf-loader\n"); diff --git a/arch/powerpc/kernel/ptrace.c b/arch/powerpc/kernel/ptrace.c index bcb83574335..4a677d1bd4e 100644 --- a/arch/powerpc/kernel/ptrace.c +++ b/arch/powerpc/kernel/ptrace.c @@ -538,7 +538,7 @@ void do_syscall_trace_enter(struct pt_regs *regs) do_syscall_trace(); if (unlikely(current->audit_context)) - audit_syscall_entry(current, + audit_syscall_entry( #ifdef CONFIG_PPC32 AUDIT_ARCH_PPC, #else @@ -556,8 +556,7 @@ void do_syscall_trace_leave(struct pt_regs *regs) #endif if (unlikely(current->audit_context)) - audit_syscall_exit(current, - (regs->ccr&0x1000)?AUDITSC_FAILURE:AUDITSC_SUCCESS, + audit_syscall_exit((regs->ccr&0x1000)?AUDITSC_FAILURE:AUDITSC_SUCCESS, regs->result); if ((test_thread_flag(TIF_SYSCALL_TRACE) diff --git a/arch/powerpc/kernel/setup-common.c b/arch/powerpc/kernel/setup-common.c index 1d93e73a700..684ab1d49c6 100644 --- a/arch/powerpc/kernel/setup-common.c +++ b/arch/powerpc/kernel/setup-common.c @@ -516,3 +516,11 @@ void probe_machine(void) printk(KERN_INFO "Using %s machine description\n", ppc_md.name); } + +int check_legacy_ioport(unsigned long base_port) +{ + if (ppc_md.check_legacy_ioport == NULL) + return 0; + return ppc_md.check_legacy_ioport(base_port); +} +EXPORT_SYMBOL(check_legacy_ioport); diff --git a/arch/powerpc/kernel/setup_64.c b/arch/powerpc/kernel/setup_64.c index 13e91c4d70a..4467c49903b 100644 --- a/arch/powerpc/kernel/setup_64.c +++ b/arch/powerpc/kernel/setup_64.c @@ -594,14 +594,6 @@ void ppc64_terminate_msg(unsigned int src, const char *msg) printk("[terminate]%04x %s\n", src, msg); } -int check_legacy_ioport(unsigned long base_port) -{ - if (ppc_md.check_legacy_ioport == NULL) - return 0; - return ppc_md.check_legacy_ioport(base_port); -} -EXPORT_SYMBOL(check_legacy_ioport); - void cpu_die(void) { if (ppc_md.cpu_die) diff --git a/arch/powerpc/kernel/sysfs.c b/arch/powerpc/kernel/sysfs.c index ed737cacf92..5bc2585c803 100644 --- a/arch/powerpc/kernel/sysfs.c +++ b/arch/powerpc/kernel/sysfs.c @@ -322,13 +322,31 @@ static void register_nodes(void) } } } + +int sysfs_add_device_to_node(struct sys_device *dev, int nid) +{ + struct node *node = &node_devices[nid]; + return sysfs_create_link(&node->sysdev.kobj, &dev->kobj, + kobject_name(&dev->kobj)); +} + +void sysfs_remove_device_from_node(struct sys_device *dev, int nid) +{ + struct node *node = &node_devices[nid]; + sysfs_remove_link(&node->sysdev.kobj, kobject_name(&dev->kobj)); +} + #else static void register_nodes(void) { return; } + #endif +EXPORT_SYMBOL_GPL(sysfs_add_device_to_node); +EXPORT_SYMBOL_GPL(sysfs_remove_device_from_node); + /* Only valid if CPU is present. */ static ssize_t show_physical_id(struct sys_device *dev, char *buf) { diff --git a/arch/powerpc/kernel/systbl.S b/arch/powerpc/kernel/systbl.S index 0b98eea73c5..cf56a1d499f 100644 --- a/arch/powerpc/kernel/systbl.S +++ b/arch/powerpc/kernel/systbl.S @@ -325,6 +325,19 @@ SYSCALL(unshare) SYSCALL(splice) SYSCALL(tee) SYSCALL(vmsplice) +COMPAT_SYS(openat) +SYSCALL(mkdirat) +SYSCALL(mknodat) +SYSCALL(fchownat) +COMPAT_SYS(futimesat) +SYSX(sys_newfstatat, sys_fstatat64, sys_fstatat64) +SYSCALL(unlinkat) +SYSCALL(renameat) +SYSCALL(linkat) +SYSCALL(symlinkat) +SYSCALL(readlinkat) +SYSCALL(fchmodat) +SYSCALL(faccessat) /* * please add new calls to arch/powerpc/platforms/cell/spu_callbacks.c diff --git a/arch/powerpc/mm/hugetlbpage.c b/arch/powerpc/mm/hugetlbpage.c index 7370f9f33e2..266b8b2ceac 100644 --- a/arch/powerpc/mm/hugetlbpage.c +++ b/arch/powerpc/mm/hugetlbpage.c @@ -30,13 +30,66 @@ #define NUM_LOW_AREAS (0x100000000UL >> SID_SHIFT) #define NUM_HIGH_AREAS (PGTABLE_RANGE >> HTLB_AREA_SHIFT) +#ifdef CONFIG_PPC_64K_PAGES +#define HUGEPTE_INDEX_SIZE (PMD_SHIFT-HPAGE_SHIFT) +#else +#define HUGEPTE_INDEX_SIZE (PUD_SHIFT-HPAGE_SHIFT) +#endif +#define PTRS_PER_HUGEPTE (1 << HUGEPTE_INDEX_SIZE) +#define HUGEPTE_TABLE_SIZE (sizeof(pte_t) << HUGEPTE_INDEX_SIZE) + +#define HUGEPD_SHIFT (HPAGE_SHIFT + HUGEPTE_INDEX_SIZE) +#define HUGEPD_SIZE (1UL << HUGEPD_SHIFT) +#define HUGEPD_MASK (~(HUGEPD_SIZE-1)) + +#define huge_pgtable_cache (pgtable_cache[HUGEPTE_CACHE_NUM]) + +/* Flag to mark huge PD pointers. This means pmd_bad() and pud_bad() + * will choke on pointers to hugepte tables, which is handy for + * catching screwups early. */ +#define HUGEPD_OK 0x1 + +typedef struct { unsigned long pd; } hugepd_t; + +#define hugepd_none(hpd) ((hpd).pd == 0) + +static inline pte_t *hugepd_page(hugepd_t hpd) +{ + BUG_ON(!(hpd.pd & HUGEPD_OK)); + return (pte_t *)(hpd.pd & ~HUGEPD_OK); +} + +static inline pte_t *hugepte_offset(hugepd_t *hpdp, unsigned long addr) +{ + unsigned long idx = ((addr >> HPAGE_SHIFT) & (PTRS_PER_HUGEPTE-1)); + pte_t *dir = hugepd_page(*hpdp); + + return dir + idx; +} + +static int __hugepte_alloc(struct mm_struct *mm, hugepd_t *hpdp, + unsigned long address) +{ + pte_t *new = kmem_cache_alloc(huge_pgtable_cache, + GFP_KERNEL|__GFP_REPEAT); + + if (! new) + return -ENOMEM; + + spin_lock(&mm->page_table_lock); + if (!hugepd_none(*hpdp)) + kmem_cache_free(huge_pgtable_cache, new); + else + hpdp->pd = (unsigned long)new | HUGEPD_OK; + spin_unlock(&mm->page_table_lock); + return 0; +} + /* Modelled after find_linux_pte() */ pte_t *huge_pte_offset(struct mm_struct *mm, unsigned long addr) { pgd_t *pg; pud_t *pu; - pmd_t *pm; - pte_t *pt; BUG_ON(! in_hugepage_area(mm->context, addr)); @@ -46,26 +99,14 @@ pte_t *huge_pte_offset(struct mm_struct *mm, unsigned long addr) if (!pgd_none(*pg)) { pu = pud_offset(pg, addr); if (!pud_none(*pu)) { - pm = pmd_offset(pu, addr); #ifdef CONFIG_PPC_64K_PAGES - /* Currently, we use the normal PTE offset within full - * size PTE pages, thus our huge PTEs are scattered in - * the PTE page and we do waste some. We may change - * that in the future, but the current mecanism keeps - * things much simpler - */ - if (!pmd_none(*pm)) { - /* Note: pte_offset_* are all equivalent on - * ppc64 as we don't have HIGHMEM - */ - pt = pte_offset_kernel(pm, addr); - return pt; - } -#else /* CONFIG_PPC_64K_PAGES */ - /* On 4k pages, we put huge PTEs in the PMD page */ - pt = (pte_t *)pm; - return pt; -#endif /* CONFIG_PPC_64K_PAGES */ + pmd_t *pm; + pm = pmd_offset(pu, addr); + if (!pmd_none(*pm)) + return hugepte_offset((hugepd_t *)pm, addr); +#else + return hugepte_offset((hugepd_t *)pu, addr); +#endif } } @@ -76,8 +117,7 @@ pte_t *huge_pte_alloc(struct mm_struct *mm, unsigned long addr) { pgd_t *pg; pud_t *pu; - pmd_t *pm; - pte_t *pt; + hugepd_t *hpdp = NULL; BUG_ON(! in_hugepage_area(mm->context, addr)); @@ -87,23 +127,182 @@ pte_t *huge_pte_alloc(struct mm_struct *mm, unsigned long addr) pu = pud_alloc(mm, pg, addr); if (pu) { +#ifdef CONFIG_PPC_64K_PAGES + pmd_t *pm; pm = pmd_alloc(mm, pu, addr); - if (pm) { + if (pm) + hpdp = (hugepd_t *)pm; +#else + hpdp = (hugepd_t *)pu; +#endif + } + + if (! hpdp) + return NULL; + + if (hugepd_none(*hpdp) && __hugepte_alloc(mm, hpdp, addr)) + return NULL; + + return hugepte_offset(hpdp, addr); +} + +static void free_hugepte_range(struct mmu_gather *tlb, hugepd_t *hpdp) +{ + pte_t *hugepte = hugepd_page(*hpdp); + + hpdp->pd = 0; + tlb->need_flush = 1; + pgtable_free_tlb(tlb, pgtable_free_cache(hugepte, HUGEPTE_CACHE_NUM, + HUGEPTE_TABLE_SIZE-1)); +} + #ifdef CONFIG_PPC_64K_PAGES - /* See comment in huge_pte_offset. Note that if we ever - * want to put the page size in the PMD, we would have - * to open code our own pte_alloc* function in order - * to populate and set the size atomically - */ - pt = pte_alloc_map(mm, pm, addr); -#else /* CONFIG_PPC_64K_PAGES */ - pt = (pte_t *)pm; -#endif /* CONFIG_PPC_64K_PAGES */ - return pt; - } +static void hugetlb_free_pmd_range(struct mmu_gather *tlb, pud_t *pud, + unsigned long addr, unsigned long end, + unsigned long floor, unsigned long ceiling) +{ + pmd_t *pmd; + unsigned long next; + unsigned long start; + + start = addr; + pmd = pmd_offset(pud, addr); + do { + next = pmd_addr_end(addr, end); + if (pmd_none(*pmd)) + continue; + free_hugepte_range(tlb, (hugepd_t *)pmd); + } while (pmd++, addr = next, addr != end); + + start &= PUD_MASK; + if (start < floor) + return; + if (ceiling) { + ceiling &= PUD_MASK; + if (!ceiling) + return; } + if (end - 1 > ceiling - 1) + return; - return NULL; + pmd = pmd_offset(pud, start); + pud_clear(pud); + pmd_free_tlb(tlb, pmd); +} +#endif + +static void hugetlb_free_pud_range(struct mmu_gather *tlb, pgd_t *pgd, + unsigned long addr, unsigned long end, + unsigned long floor, unsigned long ceiling) +{ + pud_t *pud; + unsigned long next; + unsigned long start; + + start = addr; + pud = pud_offset(pgd, addr); + do { + next = pud_addr_end(addr, end); +#ifdef CONFIG_PPC_64K_PAGES + if (pud_none_or_clear_bad(pud)) + continue; + hugetlb_free_pmd_range(tlb, pud, addr, next, floor, ceiling); +#else + if (pud_none(*pud)) + continue; + free_hugepte_range(tlb, (hugepd_t *)pud); +#endif + } while (pud++, addr = next, addr != end); + + start &= PGDIR_MASK; + if (start < floor) + return; + if (ceiling) { + ceiling &= PGDIR_MASK; + if (!ceiling) + return; + } + if (end - 1 > ceiling - 1) + return; + + pud = pud_offset(pgd, start); + pgd_clear(pgd); + pud_free_tlb(tlb, pud); +} + +/* + * This function frees user-level page tables of a process. + * + * Must be called with pagetable lock held. + */ +void hugetlb_free_pgd_range(struct mmu_gather **tlb, + unsigned long addr, unsigned long end, + unsigned long floor, unsigned long ceiling) +{ + pgd_t *pgd; + unsigned long next; + unsigned long start; + + /* + * Comments below take from the normal free_pgd_range(). They + * apply here too. The tests against HUGEPD_MASK below are + * essential, because we *don't* test for this at the bottom + * level. Without them we'll attempt to free a hugepte table + * when we unmap just part of it, even if there are other + * active mappings using it. + * + * The next few lines have given us lots of grief... + * + * Why are we testing HUGEPD* at this top level? Because + * often there will be no work to do at all, and we'd prefer + * not to go all the way down to the bottom just to discover + * that. + * + * Why all these "- 1"s? Because 0 represents both the bottom + * of the address space and the top of it (using -1 for the + * top wouldn't help much: the masks would do the wrong thing). + * The rule is that addr 0 and floor 0 refer to the bottom of + * the address space, but end 0 and ceiling 0 refer to the top + * Comparisons need to use "end - 1" and "ceiling - 1" (though + * that end 0 case should be mythical). + * + * Wherever addr is brought up or ceiling brought down, we + * must be careful to reject "the opposite 0" before it + * confuses the subsequent tests. But what about where end is + * brought down by HUGEPD_SIZE below? no, end can't go down to + * 0 there. + * + * Whereas we round start (addr) and ceiling down, by different + * masks at different levels, in order to test whether a table + * now has no other vmas using it, so can be freed, we don't + * bother to round floor or end up - the tests don't need that. + */ + + addr &= HUGEPD_MASK; + if (addr < floor) { + addr += HUGEPD_SIZE; + if (!addr) + return; + } + if (ceiling) { + ceiling &= HUGEPD_MASK; + if (!ceiling) + return; + } + if (end - 1 > ceiling - 1) + end -= HUGEPD_SIZE; + if (addr > end - 1) + return; + + start = addr; + pgd = pgd_offset((*tlb)->mm, addr); + do { + BUG_ON(! in_hugepage_area((*tlb)->mm->context, addr)); + next = pgd_addr_end(addr, end); + if (pgd_none_or_clear_bad(pgd)) + continue; + hugetlb_free_pud_range(*tlb, pgd, addr, next, floor, ceiling); + } while (pgd++, addr = next, addr != end); } void set_huge_pte_at(struct mm_struct *mm, unsigned long addr, @@ -841,3 +1040,27 @@ repeat: out: return err; } + +static void zero_ctor(void *addr, kmem_cache_t *cache, unsigned long flags) +{ + memset(addr, 0, kmem_cache_size(cache)); +} + +static int __init hugetlbpage_init(void) +{ + if (!cpu_has_feature(CPU_FTR_16M_PAGE)) + return -ENODEV; + + huge_pgtable_cache = kmem_cache_create("hugepte_cache", + HUGEPTE_TABLE_SIZE, + HUGEPTE_TABLE_SIZE, + SLAB_HWCACHE_ALIGN | + SLAB_MUST_HWCACHE_ALIGN, + zero_ctor, NULL); + if (! huge_pgtable_cache) + panic("hugetlbpage_init(): could not create hugepte cache\n"); + + return 0; +} + +module_init(hugetlbpage_init); diff --git a/arch/powerpc/mm/init_64.c b/arch/powerpc/mm/init_64.c index babebd15bdc..9e30f968c18 100644 --- a/arch/powerpc/mm/init_64.c +++ b/arch/powerpc/mm/init_64.c @@ -162,7 +162,14 @@ static const char *pgtable_cache_name[ARRAY_SIZE(pgtable_cache_size)] = { }; #endif /* CONFIG_PPC_64K_PAGES */ +#ifdef CONFIG_HUGETLB_PAGE +/* Hugepages need one extra cache, initialized in hugetlbpage.c. We + * can't put into the tables above, because HPAGE_SHIFT is not compile + * time constant. */ +kmem_cache_t *pgtable_cache[ARRAY_SIZE(pgtable_cache_size)+1]; +#else kmem_cache_t *pgtable_cache[ARRAY_SIZE(pgtable_cache_size)]; +#endif void pgtable_cache_init(void) { diff --git a/arch/powerpc/mm/numa.c b/arch/powerpc/mm/numa.c index 0a335f34974..092355f3739 100644 --- a/arch/powerpc/mm/numa.c +++ b/arch/powerpc/mm/numa.c @@ -194,7 +194,7 @@ static int *of_get_associativity(struct device_node *dev) /* Returns nid in the range [0..MAX_NUMNODES-1], or -1 if no useful numa * info is found. */ -static int of_node_to_nid(struct device_node *device) +static int of_node_to_nid_single(struct device_node *device) { int nid = -1; unsigned int *tmp; @@ -216,6 +216,28 @@ out: return nid; } +/* Walk the device tree upwards, looking for an associativity id */ +int of_node_to_nid(struct device_node *device) +{ + struct device_node *tmp; + int nid = -1; + + of_node_get(device); + while (device) { + nid = of_node_to_nid_single(device); + if (nid != -1) + break; + + tmp = device; + device = of_get_parent(tmp); + of_node_put(tmp); + } + of_node_put(device); + + return nid; +} +EXPORT_SYMBOL_GPL(of_node_to_nid); + /* * In theory, the "ibm,associativity" property may contain multiple * associativity lists because a resource may be multiply connected @@ -300,7 +322,7 @@ static int __cpuinit numa_setup_cpu(unsigned long lcpu) goto out; } - nid = of_node_to_nid(cpu); + nid = of_node_to_nid_single(cpu); if (nid < 0 || !node_online(nid)) nid = any_online_node(NODE_MASK_ALL); @@ -393,7 +415,7 @@ static int __init parse_numa_properties(void) cpu = find_cpu_node(i); BUG_ON(!cpu); - nid = of_node_to_nid(cpu); + nid = of_node_to_nid_single(cpu); of_node_put(cpu); /* @@ -437,7 +459,7 @@ new_range: * have associativity properties. If none, then * everything goes to default_nid. */ - nid = of_node_to_nid(memory); + nid = of_node_to_nid_single(memory); if (nid < 0) nid = default_nid; node_set_online(nid); @@ -776,7 +798,7 @@ int hot_add_scn_to_nid(unsigned long scn_addr) ha_new_range: start = read_n_cells(n_mem_addr_cells, &memcell_buf); size = read_n_cells(n_mem_size_cells, &memcell_buf); - nid = of_node_to_nid(memory); + nid = of_node_to_nid_single(memory); /* Domains not present at boot default to 0 */ if (nid < 0 || !node_online(nid)) diff --git a/arch/powerpc/platforms/cell/Kconfig b/arch/powerpc/platforms/cell/Kconfig index c2a3db8edb0..6a02d51086c 100644 --- a/arch/powerpc/platforms/cell/Kconfig +++ b/arch/powerpc/platforms/cell/Kconfig @@ -12,7 +12,8 @@ config SPU_FS config SPUFS_MMAP bool - depends on SPU_FS && SPARSEMEM && !PPC_64K_PAGES + depends on SPU_FS && SPARSEMEM + select MEMORY_HOTPLUG default y endmenu diff --git a/arch/powerpc/platforms/cell/setup.c b/arch/powerpc/platforms/cell/setup.c index dac5d0365fd..6574b22b3cf 100644 --- a/arch/powerpc/platforms/cell/setup.c +++ b/arch/powerpc/platforms/cell/setup.c @@ -29,6 +29,8 @@ #include <linux/seq_file.h> #include <linux/root_dev.h> #include <linux/console.h> +#include <linux/mutex.h> +#include <linux/memory_hotplug.h> #include <asm/mmu.h> #include <asm/processor.h> @@ -46,6 +48,7 @@ #include <asm/cputable.h> #include <asm/ppc-pci.h> #include <asm/irq.h> +#include <asm/spu.h> #include "interrupt.h" #include "iommu.h" @@ -69,77 +72,6 @@ static void cell_show_cpuinfo(struct seq_file *m) of_node_put(root); } -#ifdef CONFIG_SPARSEMEM -static int __init find_spu_node_id(struct device_node *spe) -{ - unsigned int *id; -#ifdef CONFIG_NUMA - struct device_node *cpu; - cpu = spe->parent->parent; - id = (unsigned int *)get_property(cpu, "node-id", NULL); -#else - id = NULL; -#endif - return id ? *id : 0; -} - -static void __init cell_spuprop_present(struct device_node *spe, - const char *prop, int early) -{ - struct address_prop { - unsigned long address; - unsigned int len; - } __attribute__((packed)) *p; - int proplen; - - unsigned long start_pfn, end_pfn, pfn; - int node_id; - - p = (void*)get_property(spe, prop, &proplen); - WARN_ON(proplen != sizeof (*p)); - - node_id = find_spu_node_id(spe); - - start_pfn = p->address >> PAGE_SHIFT; - end_pfn = (p->address + p->len + PAGE_SIZE - 1) >> PAGE_SHIFT; - - /* We need to call memory_present *before* the call to sparse_init, - but we can initialize the page structs only *after* that call. - Thus, we're being called twice. */ - if (early) - memory_present(node_id, start_pfn, end_pfn); - else { - /* As the pages backing SPU LS and I/O are outside the range - of regular memory, their page structs were not initialized - by free_area_init. Do it here instead. */ - for (pfn = start_pfn; pfn < end_pfn; pfn++) { - struct page *page = pfn_to_page(pfn); - set_page_links(page, ZONE_DMA, node_id, pfn); - init_page_count(page); - reset_page_mapcount(page); - SetPageReserved(page); - INIT_LIST_HEAD(&page->lru); - } - } -} - -static void __init cell_spumem_init(int early) -{ - struct device_node *node; - for (node = of_find_node_by_type(NULL, "spe"); - node; node = of_find_node_by_type(node, "spe")) { - cell_spuprop_present(node, "local-store", early); - cell_spuprop_present(node, "problem", early); - cell_spuprop_present(node, "priv1", early); - cell_spuprop_present(node, "priv2", early); - } -} -#else -static void __init cell_spumem_init(int early) -{ -} -#endif - static void cell_progress(char *s, unsigned short hex) { printk("*** %04x : %s\n", hex, s ? s : ""); @@ -172,8 +104,6 @@ static void __init cell_setup_arch(void) #endif mmio_nvram_init(); - - cell_spumem_init(0); } /* @@ -189,8 +119,6 @@ static void __init cell_init_early(void) ppc64_interrupt_controller = IC_CELL_PIC; - cell_spumem_init(1); - DBG(" <- cell_init_early()\n"); } diff --git a/arch/powerpc/platforms/cell/spu_base.c b/arch/powerpc/platforms/cell/spu_base.c index 269dda4fd0b..ad141fe8d52 100644 --- a/arch/powerpc/platforms/cell/spu_base.c +++ b/arch/powerpc/platforms/cell/spu_base.c @@ -306,19 +306,19 @@ spu_request_irqs(struct spu *spu) snprintf(spu->irq_c0, sizeof (spu->irq_c0), "spe%02d.0", spu->number); ret = request_irq(irq_base + spu->isrc, - spu_irq_class_0, 0, spu->irq_c0, spu); + spu_irq_class_0, SA_INTERRUPT, spu->irq_c0, spu); if (ret) goto out; snprintf(spu->irq_c1, sizeof (spu->irq_c1), "spe%02d.1", spu->number); ret = request_irq(irq_base + IIC_CLASS_STRIDE + spu->isrc, - spu_irq_class_1, 0, spu->irq_c1, spu); + spu_irq_class_1, SA_INTERRUPT, spu->irq_c1, spu); if (ret) goto out1; snprintf(spu->irq_c2, sizeof (spu->irq_c2), "spe%02d.2", spu->number); ret = request_irq(irq_base + 2*IIC_CLASS_STRIDE + spu->isrc, - spu_irq_class_2, 0, spu->irq_c2, spu); + spu_irq_class_2, SA_INTERRUPT, spu->irq_c2, spu); if (ret) goto out2; goto out; @@ -487,10 +487,14 @@ int spu_irq_class_1_bottom(struct spu *spu) ea = spu->dar; dsisr = spu->dsisr; if (dsisr & (MFC_DSISR_PTE_NOT_FOUND | MFC_DSISR_ACCESS_DENIED)) { + u64 flags; + access = (_PAGE_PRESENT | _PAGE_USER); access |= (dsisr & MFC_DSISR_ACCESS_PUT) ? _PAGE_RW : 0UL; + local_irq_save(flags); if (hash_page(ea, access, 0x300) != 0) error |= CLASS1_ENABLE_STORAGE_FAULT_INTR; + local_irq_restore(flags); } if (error & CLASS1_ENABLE_STORAGE_FAULT_INTR) { if ((ret = spu_handle_mm_fault(spu)) != 0) @@ -516,8 +520,50 @@ void spu_irq_setaffinity(struct spu *spu, int cpu) } EXPORT_SYMBOL_GPL(spu_irq_setaffinity); -static void __iomem * __init map_spe_prop(struct device_node *n, - const char *name) +static int __init find_spu_node_id(struct device_node *spe) +{ + unsigned int *id; + struct device_node *cpu; + cpu = spe->parent->parent; + id = (unsigned int *)get_property(cpu, "node-id", NULL); + return id ? *id : 0; +} + +static int __init cell_spuprop_present(struct spu *spu, struct device_node *spe, + const char *prop) +{ + static DEFINE_MUTEX(add_spumem_mutex); + + struct address_prop { + unsigned long address; + unsigned int len; + } __attribute__((packed)) *p; + int proplen; + + unsigned long start_pfn, nr_pages; + struct pglist_data *pgdata; + struct zone *zone; + int ret; + + p = (void*)get_property(spe, prop, &proplen); + WARN_ON(proplen != sizeof (*p)); + + start_pfn = p->address >> PAGE_SHIFT; + nr_pages = ((unsigned long)p->len + PAGE_SIZE - 1) >> PAGE_SHIFT; + + pgdata = NODE_DATA(spu->nid); + zone = pgdata->node_zones; + + /* XXX rethink locking here */ + mutex_lock(&add_spumem_mutex); + ret = __add_pages(zone, start_pfn, nr_pages); + mutex_unlock(&add_spumem_mutex); + + return ret; +} + +static void __iomem * __init map_spe_prop(struct spu *spu, + struct device_node *n, const char *name) { struct address_prop { unsigned long address; @@ -526,6 +572,8 @@ static void __iomem * __init map_spe_prop(struct device_node *n, void *p; int proplen; + void* ret = NULL; + int err = 0; p = get_property(n, name, &proplen); if (proplen != sizeof (struct address_prop)) @@ -533,7 +581,14 @@ static void __iomem * __init map_spe_prop(struct device_node *n, prop = p; - return ioremap(prop->address, prop->len); + err = cell_spuprop_present(spu, n, name); + if (err && (err != -EEXIST)) + goto out; + + ret = ioremap(prop->address, prop->len); + + out: + return ret; } static void spu_unmap(struct spu *spu) @@ -544,44 +599,45 @@ static void spu_unmap(struct spu *spu) iounmap((u8 __iomem *)spu->local_store); } -static int __init spu_map_device(struct spu *spu, struct device_node *spe) +static int __init spu_map_device(struct spu *spu, struct device_node *node) { char *prop; int ret; ret = -ENODEV; - prop = get_property(spe, "isrc", NULL); + prop = get_property(node, "isrc", NULL); if (!prop) goto out; spu->isrc = *(unsigned int *)prop; - spu->name = get_property(spe, "name", NULL); + spu->name = get_property(node, "name", NULL); if (!spu->name) goto out; - prop = get_property(spe, "local-store", NULL); + prop = get_property(node, "local-store", NULL); if (!prop) goto out; spu->local_store_phys = *(unsigned long *)prop; /* we use local store as ram, not io memory */ - spu->local_store = (void __force *)map_spe_prop(spe, "local-store"); + spu->local_store = (void __force *) + map_spe_prop(spu, node, "local-store"); if (!spu->local_store) goto out; - prop = get_property(spe, "problem", NULL); + prop = get_property(node, "problem", NULL); if (!prop) goto out_unmap; spu->problem_phys = *(unsigned long *)prop; - spu->problem= map_spe_prop(spe, "problem"); + spu->problem= map_spe_prop(spu, node, "problem"); if (!spu->problem) goto out_unmap; - spu->priv1= map_spe_prop(spe, "priv1"); + spu->priv1= map_spe_prop(spu, node, "priv1"); /* priv1 is not available on a hypervisor */ - spu->priv2= map_spe_prop(spe, "priv2"); + spu->priv2= map_spe_prop(spu, node, "priv2"); if (!spu->priv2) goto out_unmap; ret = 0; @@ -593,17 +649,6 @@ out: return ret; } -static int __init find_spu_node_id(struct device_node *spe) -{ - unsigned int *id; - struct device_node *cpu; - - cpu = spe->parent->parent; - id = (unsigned int *)get_property(cpu, "node-id", NULL); - - return id ? *id : 0; -} - static int __init create_spu(struct device_node *spe) { struct spu *spu; @@ -620,6 +665,10 @@ static int __init create_spu(struct device_node *spe) goto out_free; spu->node = find_spu_node_id(spe); + spu->nid = of_node_to_nid(spe); + if (spu->nid == -1) + spu->nid = 0; + spu->stop_code = 0; spu->slb_replace = 0; spu->mm = NULL; diff --git a/arch/powerpc/platforms/cell/spu_callbacks.c b/arch/powerpc/platforms/cell/spu_callbacks.c index b283380a2a1..95b36430aa0 100644 --- a/arch/powerpc/platforms/cell/spu_callbacks.c +++ b/arch/powerpc/platforms/cell/spu_callbacks.c @@ -319,6 +319,19 @@ void *spu_syscall_table[] = { [__NR_splice] sys_splice, [__NR_tee] sys_tee, [__NR_vmsplice] sys_vmsplice, + [__NR_openat] sys_openat, + [__NR_mkdirat] sys_mkdirat, + [__NR_mknodat] sys_mknodat, + [__NR_fchownat] sys_fchownat, + [__NR_futimesat] sys_futimesat, + [__NR_newfstatat] sys_newfstatat, + [__NR_unlinkat] sys_unlinkat, + [__NR_renameat] sys_renameat, + [__NR_linkat] sys_linkat, + [__NR_symlinkat] sys_symlinkat, + [__NR_readlinkat] sys_readlinkat, + [__NR_fchmodat] sys_fchmodat, + [__NR_faccessat] sys_faccessat, }; long spu_sys_callback(struct spu_syscall_block *s) diff --git a/arch/powerpc/platforms/powermac/pci.c b/arch/powerpc/platforms/powermac/pci.c index f5d8d15d74f..ea179afea63 100644 --- a/arch/powerpc/platforms/powermac/pci.c +++ b/arch/powerpc/platforms/powermac/pci.c @@ -1097,7 +1097,7 @@ pmac_pci_enable_device_hook(struct pci_dev *dev, int initial) * (iBook second controller) */ if (dev->vendor == PCI_VENDOR_ID_APPLE - && (dev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x10)) + && dev->class == PCI_CLASS_SERIAL_USB_OHCI && !node) { printk(KERN_INFO "Apple USB OHCI %s disabled by firmware\n", pci_name(dev)); diff --git a/arch/powerpc/platforms/pseries/eeh_event.c b/arch/powerpc/platforms/pseries/eeh_event.c index a1bda6f96fd..40020c65c89 100644 --- a/arch/powerpc/platforms/pseries/eeh_event.c +++ b/arch/powerpc/platforms/pseries/eeh_event.c @@ -118,7 +118,15 @@ int eeh_send_failure_event (struct device_node *dn, { unsigned long flags; struct eeh_event *event; + char *location; + if (!mem_init_done) { + printk(KERN_ERR "EEH: event during early boot not handled\n"); + location = (char *) get_property(dn, "ibm,loc-code", NULL); + printk(KERN_ERR "EEH: device node = %s\n", dn->full_name); + printk(KERN_ERR "EEH: PCI location = %s\n", location); + return 1; + } event = kmalloc(sizeof(*event), GFP_ATOMIC); if (event == NULL) { printk (KERN_ERR "EEH: out of memory, event not handled\n"); diff --git a/arch/ppc/kernel/head_8xx.S b/arch/ppc/kernel/head_8xx.S index ec53c7d65f2..7a2f20583be 100644 --- a/arch/ppc/kernel/head_8xx.S +++ b/arch/ppc/kernel/head_8xx.S @@ -355,9 +355,7 @@ InstructionTLBMiss: . = 0x1200 DataStoreTLBMiss: -#ifdef CONFIG_8xx_CPU6 stw r3, 8(r0) -#endif DO_8xx_CPU6(0x3f80, r3) mtspr SPRN_M_TW, r10 /* Save a couple of working registers */ mfcr r10 @@ -417,9 +415,7 @@ DataStoreTLBMiss: lwz r11, 0(r0) mtcr r11 lwz r11, 4(r0) -#ifdef CONFIG_8xx_CPU6 lwz r3, 8(r0) -#endif rfi /* This is an instruction TLB error on the MPC8xx. This could be due diff --git a/arch/ppc/platforms/4xx/ocotea.c b/arch/ppc/platforms/4xx/ocotea.c index f841972f1fa..554776d4b8a 100644 --- a/arch/ppc/platforms/4xx/ocotea.c +++ b/arch/ppc/platforms/4xx/ocotea.c @@ -331,7 +331,7 @@ static void __init ocotea_init(void) void __init platform_init(unsigned long r3, unsigned long r4, unsigned long r5, unsigned long r6, unsigned long r7) { - ibm44x_platform_init(r3, r4, r5, r6, r7); + ibm440gx_platform_init(r3, r4, r5, r6, r7); ppc_md.setup_arch = ocotea_setup_arch; ppc_md.show_cpuinfo = ocotea_show_cpuinfo; diff --git a/arch/ppc/platforms/mpc8272ads_setup.c b/arch/ppc/platforms/mpc8272ads_setup.c index bc9b94f77e3..e62b75707f7 100644 --- a/arch/ppc/platforms/mpc8272ads_setup.c +++ b/arch/ppc/platforms/mpc8272ads_setup.c @@ -26,11 +26,35 @@ #include <asm/irq.h> #include <asm/ppc_sys.h> #include <asm/ppcboot.h> +#include <linux/fs_uart_pd.h> #include "pq2ads_pd.h" static void init_fcc1_ioports(void); static void init_fcc2_ioports(void); +static void init_scc1_uart_ioports(void); +static void init_scc4_uart_ioports(void); + +static struct fs_uart_platform_info mpc8272_uart_pdata[] = { + [fsid_scc1_uart] = { + .init_ioports = init_scc1_uart_ioports, + .fs_no = fsid_scc1_uart, + .brg = 1, + .tx_num_fifo = 4, + .tx_buf_size = 32, + .rx_num_fifo = 4, + .rx_buf_size = 32, + }, + [fsid_scc4_uart] = { + .init_ioports = init_scc4_uart_ioports, + .fs_no = fsid_scc4_uart, + .brg = 4, + .tx_num_fifo = 4, + .tx_buf_size = 32, + .rx_num_fifo = 4, + .rx_buf_size = 32, + }, +}; static struct fs_mii_bus_info mii_bus_info = { .method = fsmii_bitbang, @@ -201,6 +225,55 @@ static void __init mpc8272ads_fixup_enet_pdata(struct platform_device *pdev, } } +static void mpc8272ads_fixup_uart_pdata(struct platform_device *pdev, + int idx) +{ + bd_t *bd = (bd_t *) __res; + struct fs_uart_platform_info *pinfo; + int num = ARRAY_SIZE(mpc8272_uart_pdata); + int id = fs_uart_id_scc2fsid(idx); + + /* no need to alter anything if console */ + if ((id <= num) && (!pdev->dev.platform_data)) { + pinfo = &mpc8272_uart_pdata[id]; + pinfo->uart_clk = bd->bi_intfreq; + pdev->dev.platform_data = pinfo; + } +} + +static void init_scc1_uart_ioports(void) +{ + cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t)); + + /* SCC1 is only on port D */ + setbits32(&immap->im_ioport.iop_ppard,0x00000003); + clrbits32(&immap->im_ioport.iop_psord,0x00000001); + setbits32(&immap->im_ioport.iop_psord,0x00000002); + clrbits32(&immap->im_ioport.iop_pdird,0x00000001); + setbits32(&immap->im_ioport.iop_pdird,0x00000002); + + /* Wire BRG1 to SCC1 */ + clrbits32(&immap->im_cpmux.cmx_scr,0x00ffffff); + + iounmap(immap); +} + +static void init_scc4_uart_ioports(void) +{ + cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t)); + + setbits32(&immap->im_ioport.iop_ppard,0x00000600); + clrbits32(&immap->im_ioport.iop_psord,0x00000600); + clrbits32(&immap->im_ioport.iop_pdird,0x00000200); + setbits32(&immap->im_ioport.iop_pdird,0x00000400); + + /* Wire BRG4 to SCC4 */ + clrbits32(&immap->im_cpmux.cmx_scr,0x000000ff); + setbits32(&immap->im_cpmux.cmx_scr,0x0000001b); + + iounmap(immap); +} + static int mpc8272ads_platform_notify(struct device *dev) { static const struct platform_notify_dev_map dev_map[] = { @@ -209,6 +282,10 @@ static int mpc8272ads_platform_notify(struct device *dev) .rtn = mpc8272ads_fixup_enet_pdata }, { + .bus_id = "fsl-cpm-scc:uart", + .rtn = mpc + }, + { .bus_id = NULL } }; @@ -230,7 +307,44 @@ int __init mpc8272ads_init(void) ppc_sys_device_enable(MPC82xx_CPM_FCC1); ppc_sys_device_enable(MPC82xx_CPM_FCC2); + /* to be ready for console, let's attach pdata here */ +#ifdef CONFIG_SERIAL_CPM_SCC1 + ppc_sys_device_setfunc(MPC82xx_CPM_SCC1, PPC_SYS_FUNC_UART); + ppc_sys_device_enable(MPC82xx_CPM_SCC1); + +#endif + +#ifdef CONFIG_SERIAL_CPM_SCC4 + ppc_sys_device_setfunc(MPC82xx_CPM_SCC4, PPC_SYS_FUNC_UART); + ppc_sys_device_enable(MPC82xx_CPM_SCC4); +#endif + + return 0; } +/* + To prevent confusion, console selection is gross: + by 0 assumed SCC1 and by 1 assumed SCC4 + */ +struct platform_device* early_uart_get_pdev(int index) +{ + bd_t *bd = (bd_t *) __res; + struct fs_uart_platform_info *pinfo; + + struct platform_device* pdev = NULL; + if(index) { /*assume SCC4 here*/ + pdev = &ppc_sys_platform_devices[MPC82xx_CPM_SCC4]; + pinfo = &mpc8272<F12>_uart_pdata[1]; + } else { /*over SCC1*/ + pdev = &ppc_sys_platform_devices[MPC82xx_CPM_SCC1]; + pinfo = &mpc8272_uart_pdata[0]; + } + + pinfo->uart_clk = bd->bi_intfreq; + pdev->dev.platform_data = pinfo; + ppc_sys_fixup_mem_resource(pdev, IMAP_ADDR); + return NULL; +} + arch_initcall(mpc8272ads_init); diff --git a/arch/ppc/platforms/mpc866ads_setup.c b/arch/ppc/platforms/mpc866ads_setup.c index ac8fcc68afe..d919dab6134 100644 --- a/arch/ppc/platforms/mpc866ads_setup.c +++ b/arch/ppc/platforms/mpc866ads_setup.c @@ -20,6 +20,7 @@ #include <linux/device.h> #include <linux/fs_enet_pd.h> +#include <linux/fs_uart_pd.h> #include <linux/mii.h> #include <asm/delay.h> @@ -37,6 +38,11 @@ extern unsigned char __res[]; +static void setup_fec1_ioports(void); +static void setup_scc1_ioports(void); +static void setup_smc1_ioports(void); +static void setup_smc2_ioports(void); + static struct fs_mii_bus_info fec_mii_bus_info = { .method = fsmii_fec, .id = 0, @@ -79,6 +85,28 @@ static struct fs_platform_info mpc8xx_scc_pdata = { .phy_irq = -1, .bus_info = &scc_mii_bus_info, + +}; + +static struct fs_uart_platform_info mpc866_uart_pdata[] = { + [fsid_smc1_uart] = { + .brg = 1, + .fs_no = fsid_smc1_uart, + .init_ioports = setup_smc1_ioports, + .tx_num_fifo = 4, + .tx_buf_size = 32, + .rx_num_fifo = 4, + .rx_buf_size = 32, + }, + [fsid_smc2_uart] = { + .brg = 2, + .fs_no = fsid_smc2_uart, + .init_ioports = setup_smc2_ioports, + .tx_num_fifo = 4, + .tx_buf_size = 32, + .rx_num_fifo = 4, + .rx_buf_size = 32, + }, }; void __init board_init(void) @@ -92,9 +120,12 @@ void __init board_init(void) printk(KERN_CRIT "Could not remap BCSR1\n"); return; } + #ifdef CONFIG_SERIAL_CPM_SMC1 cp->cp_simode &= ~(0xe0000000 >> 17); /* brg1 */ clrbits32(bcsr_io,(0x80000000 >> 7)); + cp->cp_smc[0].smc_smcm |= (SMCM_RX | SMCM_TX); + cp->cp_smc[0].smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); #else setbits32(bcsr_io,(0x80000000 >> 7)); @@ -108,6 +139,8 @@ void __init board_init(void) cp->cp_simode &= ~(0xe0000000 >> 1); cp->cp_simode |= (0x20000000 >> 1); /* brg2 */ clrbits32(bcsr_io,(0x80000000 >> 13)); + cp->cp_smc[1].smc_smcm |= (SMCM_RX | SMCM_TX); + cp->cp_smc[1].smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); #else clrbits32(bcsr_io,(0x80000000 >> 13)); cp->cp_pbpar &= ~(0x00000c00); @@ -232,6 +265,74 @@ static void mpc866ads_fixup_scc_enet_pdata(struct platform_device *pdev, mpc866ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1); } +static void setup_smc1_ioports(void) +{ + immap_t *immap = (immap_t *) IMAP_ADDR; + unsigned *bcsr_io; + unsigned int iobits = 0x000000c0; + + bcsr_io = ioremap(BCSR1, sizeof(unsigned long)); + + if (bcsr_io == NULL) { + printk(KERN_CRIT "Could not remap BCSR1\n"); + return; + } + + clrbits32(bcsr_io,BCSR1_RS232EN_1); + iounmap(bcsr_io); + + setbits32(&immap->im_cpm.cp_pbpar, iobits); + clrbits32(&immap->im_cpm.cp_pbdir, iobits); + clrbits16(&immap->im_cpm.cp_pbodr, iobits); + +} + +static void setup_smc2_ioports(void) +{ + immap_t *immap = (immap_t *) IMAP_ADDR; + unsigned *bcsr_io; + unsigned int iobits = 0x00000c00; + + bcsr_io = ioremap(BCSR1, sizeof(unsigned long)); + + if (bcsr_io == NULL) { + printk(KERN_CRIT "Could not remap BCSR1\n"); + return; + } + + clrbits32(bcsr_io,BCSR1_RS232EN_2); + + iounmap(bcsr_io); + +#ifndef CONFIG_SERIAL_CPM_ALT_SMC2 + setbits32(&immap->im_cpm.cp_pbpar, iobits); + clrbits32(&immap->im_cpm.cp_pbdir, iobits); + clrbits16(&immap->im_cpm.cp_pbodr, iobits); +#else + setbits16(&immap->im_ioport.iop_papar, iobits); + clrbits16(&immap->im_ioport.iop_padir, iobits); + clrbits16(&immap->im_ioport.iop_paodr, iobits); +#endif + +} + +static void __init mpc866ads_fixup_uart_pdata(struct platform_device *pdev, + int idx) +{ + bd_t *bd = (bd_t *) __res; + struct fs_uart_platform_info *pinfo; + int num = ARRAY_SIZE(mpc866_uart_pdata); + + int id = fs_uart_id_smc2fsid(idx); + + /* no need to alter anything if console */ + if ((id <= num) && (!pdev->dev.platform_data)) { + pinfo = &mpc866_uart_pdata[id]; + pinfo->uart_clk = bd->bi_intfreq; + pdev->dev.platform_data = pinfo; + } +} + static int mpc866ads_platform_notify(struct device *dev) { static const struct platform_notify_dev_map dev_map[] = { @@ -244,6 +345,10 @@ static int mpc866ads_platform_notify(struct device *dev) .rtn = mpc866ads_fixup_scc_enet_pdata, }, { + .bus_id = "fsl-cpm-smc:uart", + .rtn = mpc866ads_fixup_uart_pdata + }, + { .bus_id = NULL } }; @@ -267,7 +372,42 @@ int __init mpc866ads_init(void) #endif ppc_sys_device_enable(MPC8xx_CPM_FEC1); +/* Since either of the uarts could be used as console, they need to ready */ +#ifdef CONFIG_SERIAL_CPM_SMC1 + ppc_sys_device_enable(MPC8xx_CPM_SMC1); + ppc_sys_device_setfunc(MPC8xx_CPM_SMC1, PPC_SYS_FUNC_UART); +#endif + +#ifdef CONFIG_SERIAL_CPM_SMC + ppc_sys_device_enable(MPC8xx_CPM_SMC2); + ppc_sys_device_setfunc(MPC8xx_CPM_SMC2, PPC_SYS_FUNC_UART); +#endif + return 0; } +/* + To prevent confusion, console selection is gross: + by 0 assumed SMC1 and by 1 assumed SMC2 + */ +struct platform_device* early_uart_get_pdev(int index) +{ + bd_t *bd = (bd_t *) __res; + struct fs_uart_platform_info *pinfo; + + struct platform_device* pdev = NULL; + if(index) { /*assume SMC2 here*/ + pdev = &ppc_sys_platform_devices[MPC8xx_CPM_SMC2]; + pinfo = &mpc866_uart_pdata[1]; + } else { /*over SMC1*/ + pdev = &ppc_sys_platform_devices[MPC8xx_CPM_SMC1]; + pinfo = &mpc866_uart_pdata[0]; + } + + pinfo->uart_clk = bd->bi_intfreq; + pdev->dev.platform_data = pinfo; + ppc_sys_fixup_mem_resource(pdev, IMAP_ADDR); + return NULL; +} + arch_initcall(mpc866ads_init); diff --git a/arch/ppc/platforms/mpc885ads_setup.c b/arch/ppc/platforms/mpc885ads_setup.c index 50a99e5f7c6..4b88679cd31 100644 --- a/arch/ppc/platforms/mpc885ads_setup.c +++ b/arch/ppc/platforms/mpc885ads_setup.c @@ -20,6 +20,7 @@ #include <linux/device.h> #include <linux/fs_enet_pd.h> +#include <linux/fs_uart_pd.h> #include <linux/mii.h> #include <asm/delay.h> @@ -35,9 +36,32 @@ #include <asm/ppc_sys.h> extern unsigned char __res[]; +static void setup_smc1_ioports(void); +static void setup_smc2_ioports(void); static void __init mpc885ads_scc_phy_init(char); +static struct fs_uart_platform_info mpc885_uart_pdata[] = { + [fsid_smc1_uart] = { + .brg = 1, + .fs_no = fsid_smc1_uart, + .init_ioports = setup_smc1_ioports, + .tx_num_fifo = 4, + .tx_buf_size = 32, + .rx_num_fifo = 4, + .rx_buf_size = 32, + }, + [fsid_smc2_uart] = { + .brg = 2, + .fs_no = fsid_smc2_uart, + .init_ioports = setup_smc2_ioports, + .tx_num_fifo = 4, + .tx_buf_size = 32, + .rx_num_fifo = 4, + .rx_buf_size = 32, + }, +}; + static struct fs_mii_bus_info fec_mii_bus_info = { .method = fsmii_fec, .id = 0, @@ -116,6 +140,8 @@ void __init board_init(void) #ifdef CONFIG_SERIAL_CPM_SMC1 cp->cp_simode &= ~(0xe0000000 >> 17); /* brg1 */ clrbits32(bcsr_io, BCSR1_RS232EN_1); + cp->cp_smc[0].smc_smcm |= (SMCM_RX | SMCM_TX); + cp->cp_smc[0].smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); #else setbits32(bcsr_io,BCSR1_RS232EN_1); cp->cp_smc[0].smc_smcmr = 0; @@ -126,6 +152,8 @@ void __init board_init(void) cp->cp_simode &= ~(0xe0000000 >> 1); cp->cp_simode |= (0x20000000 >> 1); /* brg2 */ clrbits32(bcsr_io,BCSR1_RS232EN_2); + cp->cp_smc[1].smc_smcm |= (SMCM_RX | SMCM_TX); + cp->cp_smc[1].smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); #else setbits32(bcsr_io,BCSR1_RS232EN_2); cp->cp_smc[1].smc_smcmr = 0; @@ -343,6 +371,70 @@ static void mpc885ads_scc_phy_init(char phy_addr) out_be32(&fecp->fec_mii_speed, 0); } +static void setup_smc1_ioports(void) +{ + immap_t *immap = (immap_t *) IMAP_ADDR; + unsigned *bcsr_io; + unsigned int iobits = 0x000000c0; + + bcsr_io = ioremap(BCSR1, sizeof(unsigned long)); + + if (bcsr_io == NULL) { + printk(KERN_CRIT "Could not remap BCSR1\n"); + return; + } + clrbits32(bcsr_io,BCSR1_RS232EN_1); + iounmap(bcsr_io); + + setbits32(&immap->im_cpm.cp_pbpar, iobits); + clrbits32(&immap->im_cpm.cp_pbdir, iobits); + clrbits16(&immap->im_cpm.cp_pbodr, iobits); +} + +static void setup_smc2_ioports(void) +{ + immap_t *immap = (immap_t *) IMAP_ADDR; + unsigned *bcsr_io; + unsigned int iobits = 0x00000c00; + + bcsr_io = ioremap(BCSR1, sizeof(unsigned long)); + + if (bcsr_io == NULL) { + printk(KERN_CRIT "Could not remap BCSR1\n"); + return; + } + clrbits32(bcsr_io,BCSR1_RS232EN_2); + iounmap(bcsr_io); + +#ifndef CONFIG_SERIAL_CPM_ALT_SMC2 + setbits32(&immap->im_cpm.cp_pbpar, iobits); + clrbits32(&immap->im_cpm.cp_pbdir, iobits); + clrbits16(&immap->im_cpm.cp_pbodr, iobits); +#else + setbits16(&immap->im_ioport.iop_papar, iobits); + clrbits16(&immap->im_ioport.iop_padir, iobits); + clrbits16(&immap->im_ioport.iop_paodr, iobits); +#endif +} + +static void __init mpc885ads_fixup_uart_pdata(struct platform_device *pdev, + int idx) +{ + bd_t *bd = (bd_t *) __res; + struct fs_uart_platform_info *pinfo; + int num = ARRAY_SIZE(mpc885_uart_pdata); + + int id = fs_uart_id_smc2fsid(idx); + + /* no need to alter anything if console */ + if ((id <= num) && (!pdev->dev.platform_data)) { + pinfo = &mpc885_uart_pdata[id]; + pinfo->uart_clk = bd->bi_intfreq; + pdev->dev.platform_data = pinfo; + } +} + + static int mpc885ads_platform_notify(struct device *dev) { @@ -356,12 +448,17 @@ static int mpc885ads_platform_notify(struct device *dev) .rtn = mpc885ads_fixup_scc_enet_pdata, }, { + .bus_id = "fsl-cpm-smc:uart", + .rtn = mpc885ads_fixup_uart_pdata + }, + { .bus_id = NULL } }; platform_notify_map(dev_map,dev); + return 0; } int __init mpc885ads_init(void) @@ -383,7 +480,41 @@ int __init mpc885ads_init(void) ppc_sys_device_enable(MPC8xx_CPM_FEC2); #endif +#ifdef CONFIG_SERIAL_CPM_SMC1 + ppc_sys_device_enable(MPC8xx_CPM_SMC1); + ppc_sys_device_setfunc(MPC8xx_CPM_SMC1, PPC_SYS_FUNC_UART); +#endif + +#ifdef CONFIG_SERIAL_CPM_SMC2 + ppc_sys_device_enable(MPC8xx_CPM_SMC2); + ppc_sys_device_setfunc(MPC8xx_CPM_SMC2, PPC_SYS_FUNC_UART); +#endif return 0; } arch_initcall(mpc885ads_init); + +/* + To prevent confusion, console selection is gross: + by 0 assumed SMC1 and by 1 assumed SMC2 + */ +struct platform_device* early_uart_get_pdev(int index) +{ + bd_t *bd = (bd_t *) __res; + struct fs_uart_platform_info *pinfo; + + struct platform_device* pdev = NULL; + if(index) { /*assume SMC2 here*/ + pdev = &ppc_sys_platform_devices[MPC8xx_CPM_SMC2]; + pinfo = &mpc885_uart_pdata[1]; + } else { /*over SMC1*/ + pdev = &ppc_sys_platform_devices[MPC8xx_CPM_SMC1]; + pinfo = &mpc885_uart_pdata[0]; + } + + pinfo->uart_clk = bd->bi_intfreq; + pdev->dev.platform_data = pinfo; + ppc_sys_fixup_mem_resource(pdev, IMAP_ADDR); + return NULL; +} + diff --git a/arch/ppc/platforms/pq2ads.c b/arch/ppc/platforms/pq2ads.c index 3365fd788a7..7fc2e02f524 100644 --- a/arch/ppc/platforms/pq2ads.c +++ b/arch/ppc/platforms/pq2ads.c @@ -14,11 +14,40 @@ #include <linux/init.h> +#include <asm/io.h> #include <asm/mpc8260.h> +#include <asm/cpm2.h> +#include <asm/immap_cpm2.h> void __init m82xx_board_setup(void) { + cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t)); + u32 *bcsr = ioremap(BCSR_ADDR+4, sizeof(u32)); + /* Enable the 2nd UART port */ - *(volatile uint *)(BCSR_ADDR + 4) &= ~BCSR1_RS232_EN2; + clrbits32(bcsr, BCSR1_RS232_EN2); + +#ifdef CONFIG_SERIAL_CPM_SCC1 + clrbits32((u32*)&immap->im_scc[0].scc_sccm, UART_SCCM_TX | UART_SCCM_RX); + clrbits32((u32*)&immap->im_scc[0].scc_gsmrl, SCC_GSMRL_ENR | SCC_GSMRL_ENT); +#endif + +#ifdef CONFIG_SERIAL_CPM_SCC2 + clrbits32((u32*)&immap->im_scc[1].scc_sccm, UART_SCCM_TX | UART_SCCM_RX); + clrbits32((u32*)&immap->im_scc[1].scc_gsmrl, SCC_GSMRL_ENR | SCC_GSMRL_ENT); +#endif + +#ifdef CONFIG_SERIAL_CPM_SCC3 + clrbits32((u32*)&immap->im_scc[2].scc_sccm, UART_SCCM_TX | UART_SCCM_RX); + clrbits32((u32*)&immap->im_scc[2].scc_gsmrl, SCC_GSMRL_ENR | SCC_GSMRL_ENT); +#endif + +#ifdef CONFIG_SERIAL_CPM_SCC4 + clrbits32((u32*)&immap->im_scc[3].scc_sccm, UART_SCCM_TX | UART_SCCM_RX); + clrbits32((u32*)&immap->im_scc[3].scc_gsmrl, SCC_GSMRL_ENR | SCC_GSMRL_ENT); +#endif + + iounmap(bcsr); + iounmap(immap); } diff --git a/arch/ppc/syslib/ibm440gx_common.c b/arch/ppc/syslib/ibm440gx_common.c index a7dd55f1c63..f6cc1688852 100644 --- a/arch/ppc/syslib/ibm440gx_common.c +++ b/arch/ppc/syslib/ibm440gx_common.c @@ -2,7 +2,7 @@ * PPC440GX system library * * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> - * Copyright (c) 2003, 2004 Zultys Technologies + * Copyright (c) 2003 - 2006 Zultys Technologies * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the @@ -282,3 +282,14 @@ int ibm440gx_show_cpuinfo(struct seq_file *m){ return 0; } +void __init ibm440gx_platform_init(unsigned long r3, unsigned long r4, + unsigned long r5, unsigned long r6, + unsigned long r7) +{ + /* Erratum 440_43 workaround, disable L1 cache parity checking */ + if (!strcmp(cur_cpu_spec->cpu_name, "440GX Rev. C") || + !strcmp(cur_cpu_spec->cpu_name, "440GX Rev. F")) + mtspr(SPRN_CCR1, mfspr(SPRN_CCR1) | CCR1_DPC); + + ibm44x_platform_init(r3, r4, r5, r6, r7); +} diff --git a/arch/ppc/syslib/ibm440gx_common.h b/arch/ppc/syslib/ibm440gx_common.h index a2ab9fab8e3..a03ec6022e8 100644 --- a/arch/ppc/syslib/ibm440gx_common.h +++ b/arch/ppc/syslib/ibm440gx_common.h @@ -29,6 +29,10 @@ void ibm440gx_get_clocks(struct ibm44x_clocks*, unsigned int sys_clk, unsigned int ser_clk) __init; +/* common 440GX platform init */ +void ibm440gx_platform_init(unsigned long r3, unsigned long r4, unsigned long r5, + unsigned long r6, unsigned long r7) __init; + /* Enable L2 cache */ void ibm440gx_l2c_enable(void) __init; diff --git a/arch/ppc/syslib/mpc8xx_devices.c b/arch/ppc/syslib/mpc8xx_devices.c index bd41ed83beb..6f536383866 100644 --- a/arch/ppc/syslib/mpc8xx_devices.c +++ b/arch/ppc/syslib/mpc8xx_devices.c @@ -170,12 +170,18 @@ struct platform_device ppc_sys_platform_devices[] = { [MPC8xx_CPM_SMC1] = { .name = "fsl-cpm-smc", .id = 1, - .num_resources = 2, + .num_resources = 3, .resource = (struct resource[]) { { .name = "regs", - .start = 0xa82, - .end = 0xa91, + .start = 0xa80, + .end = 0xa8f, + .flags = IORESOURCE_MEM, + }, + { + .name = "pram", + .start = 0x3e80, + .end = 0x3ebf, .flags = IORESOURCE_MEM, }, { @@ -189,15 +195,22 @@ struct platform_device ppc_sys_platform_devices[] = { [MPC8xx_CPM_SMC2] = { .name = "fsl-cpm-smc", .id = 2, - .num_resources = 2, + .num_resources = 3, .resource = (struct resource[]) { { .name = "regs", - .start = 0xa92, - .end = 0xaa1, + .start = 0xa90, + .end = 0xa9f, .flags = IORESOURCE_MEM, }, { + .name = "pram", + .start = 0x3f80, + .end = 0x3fbf, + .flags = IORESOURCE_MEM, + + }, + { .name = "interrupt", .start = MPC8xx_INT_SMC2, .end = MPC8xx_INT_SMC2, diff --git a/arch/ppc/syslib/ppc_sys.c b/arch/ppc/syslib/ppc_sys.c index 7662c4e6e7d..2d48018b71d 100644 --- a/arch/ppc/syslib/ppc_sys.c +++ b/arch/ppc/syslib/ppc_sys.c @@ -109,9 +109,11 @@ ppc_sys_fixup_mem_resource(struct platform_device *pdev, phys_addr_t paddr) int i; for (i = 0; i < pdev->num_resources; i++) { struct resource *r = &pdev->resource[i]; - if ((r->flags & IORESOURCE_MEM) == IORESOURCE_MEM) { + if (((r->flags & IORESOURCE_MEM) == IORESOURCE_MEM) && + ((r->flags & PPC_SYS_IORESOURCE_FIXUPPED) != PPC_SYS_IORESOURCE_FIXUPPED)) { r->start += paddr; r->end += paddr; + r->flags |= PPC_SYS_IORESOURCE_FIXUPPED; } } } diff --git a/arch/ppc/syslib/pq2_sys.c b/arch/ppc/syslib/pq2_sys.c index 75e64f1c144..433b0fa203e 100644 --- a/arch/ppc/syslib/pq2_sys.c +++ b/arch/ppc/syslib/pq2_sys.c @@ -113,13 +113,13 @@ struct ppc_sys_spec ppc_sys_specs[] = { .ppc_sys_name = "8248", .mask = 0x0000ff00, .value = 0x00000c00, - .num_devices = 11, + .num_devices = 12, .device_list = (enum ppc_sys_devices[]) { MPC82xx_CPM_FCC1, MPC82xx_CPM_FCC2, MPC82xx_CPM_SCC1, - MPC82xx_CPM_SCC2, MPC82xx_CPM_SCC3, MPC82xx_CPM_SMC1, - MPC82xx_CPM_SMC2, MPC82xx_CPM_SPI, MPC82xx_CPM_I2C, - MPC82xx_CPM_USB, MPC82xx_SEC1, + MPC82xx_CPM_SCC2, MPC82xx_CPM_SCC3, MPC82xx_CPM_SCC4, + MPC82xx_CPM_SMC1, MPC82xx_CPM_SMC2, MPC82xx_CPM_SPI, + MPC82xx_CPM_I2C, MPC82xx_CPM_USB, MPC82xx_SEC1, }, }, { diff --git a/arch/s390/kernel/compat_signal.c b/arch/s390/kernel/compat_signal.c index 5291b5f8788..b4c815d8ef7 100644 --- a/arch/s390/kernel/compat_signal.c +++ b/arch/s390/kernel/compat_signal.c @@ -430,7 +430,7 @@ get_sigframe(struct k_sigaction *ka, struct pt_regs * regs, size_t frame_size) /* This is the X/Open sanctioned signal stack switching. */ if (ka->sa.sa_flags & SA_ONSTACK) { - if (! on_sig_stack(sp)) + if (! sas_ss_flags(sp)) sp = current->sas_ss_sp + current->sas_ss_size; } diff --git a/arch/s390/kernel/compat_wrapper.S b/arch/s390/kernel/compat_wrapper.S index 199da68bd7b..ef5b9c44b86 100644 --- a/arch/s390/kernel/compat_wrapper.S +++ b/arch/s390/kernel/compat_wrapper.S @@ -1608,3 +1608,45 @@ compat_sys_ppoll_wrapper: sys_unshare_wrapper: llgfr %r2,%r2 # unsigned long jg sys_unshare + + .globl compat_sys_set_robust_list_wrapper +compat_sys_set_robust_list_wrapper: + llgtr %r2,%r2 # struct compat_robust_list_head * + llgfr %r3,%r3 # size_t + jg compat_sys_set_robust_list + + .globl compat_sys_get_robust_list_wrapper +compat_sys_get_robust_list_wrapper: + lgfr %r2,%r2 # int + llgtr %r3,%r3 # compat_uptr_t_t * + llgtr %r4,%r4 # compat_size_t * + jg compat_sys_get_robust_list + + .globl sys_splice_wrapper +sys_splice_wrapper: + lgfr %r2,%r2 # int + llgtr %r3,%r3 # loff_t * + lgfr %r4,%r4 # int + llgtr %r5,%r5 # loff_t * + llgfr %r6,%r6 # size_t + llgf %r0,164(%r15) # unsigned int + stg %r0,160(%r15) + jg sys_splice + + .globl sys_sync_file_range_wrapper +sys_sync_file_range_wrapper: + lgfr %r2,%r2 # int + sllg %r3,%r3,32 # get high word of 64bit loff_t + or %r3,%r4 # get low word of 64bit loff_t + sllg %r4,%r5,32 # get high word of 64bit loff_t + or %r4,%r6 # get low word of 64bit loff_t + llgf %r5,164(%r15) # unsigned int + jg sys_sync_file_range + + .globl sys_tee_wrapper +sys_tee_wrapper: + lgfr %r2,%r2 # int + lgfr %r3,%r3 # int + llgfr %r4,%r4 # size_t + llgfr %r5,%r5 # unsigned int + jg sys_tee diff --git a/arch/s390/kernel/ptrace.c b/arch/s390/kernel/ptrace.c index 37dfe33dab7..8f36504075e 100644 --- a/arch/s390/kernel/ptrace.c +++ b/arch/s390/kernel/ptrace.c @@ -734,7 +734,7 @@ asmlinkage void syscall_trace(struct pt_regs *regs, int entryexit) { if (unlikely(current->audit_context) && entryexit) - audit_syscall_exit(current, AUDITSC_RESULT(regs->gprs[2]), regs->gprs[2]); + audit_syscall_exit(AUDITSC_RESULT(regs->gprs[2]), regs->gprs[2]); if (!test_thread_flag(TIF_SYSCALL_TRACE)) goto out; @@ -761,8 +761,7 @@ syscall_trace(struct pt_regs *regs, int entryexit) } out: if (unlikely(current->audit_context) && !entryexit) - audit_syscall_entry(current, - test_thread_flag(TIF_31BIT)?AUDIT_ARCH_S390:AUDIT_ARCH_S390X, + audit_syscall_entry(test_thread_flag(TIF_31BIT)?AUDIT_ARCH_S390:AUDIT_ARCH_S390X, regs->gprs[2], regs->orig_gpr2, regs->gprs[3], regs->gprs[4], regs->gprs[5]); } diff --git a/arch/s390/kernel/signal.c b/arch/s390/kernel/signal.c index ae1927e48cf..d48cfc726b6 100644 --- a/arch/s390/kernel/signal.c +++ b/arch/s390/kernel/signal.c @@ -358,8 +358,9 @@ static int setup_rt_frame(int sig, struct k_sigaction *ka, siginfo_t *info, } else { regs->gprs[14] = (unsigned long) frame->retcode | PSW_ADDR_AMODE; - err |= __put_user(S390_SYSCALL_OPCODE | __NR_rt_sigreturn, - (u16 __user *)(frame->retcode)); + if (__put_user(S390_SYSCALL_OPCODE | __NR_rt_sigreturn, + (u16 __user *)(frame->retcode))) + goto give_sigsegv; } /* Set up backchain. */ diff --git a/arch/s390/kernel/syscalls.S b/arch/s390/kernel/syscalls.S index 2f56654da82..fc2c0767202 100644 --- a/arch/s390/kernel/syscalls.S +++ b/arch/s390/kernel/syscalls.S @@ -312,3 +312,8 @@ SYSCALL(sys_faccessat,sys_faccessat,sys_faccessat_wrapper) /* 300 */ SYSCALL(sys_pselect6,sys_pselect6,compat_sys_pselect6_wrapper) SYSCALL(sys_ppoll,sys_ppoll,compat_sys_ppoll_wrapper) SYSCALL(sys_unshare,sys_unshare,sys_unshare_wrapper) +SYSCALL(sys_set_robust_list,sys_set_robust_list,compat_sys_set_robust_list_wrapper) +SYSCALL(sys_get_robust_list,sys_get_robust_list,compat_sys_get_robust_list_wrapper) +SYSCALL(sys_splice,sys_splice,sys_splice_wrapper) +SYSCALL(sys_sync_file_range,sys_sync_file_range,sys_sync_file_range_wrapper) +SYSCALL(sys_tee,sys_tee,sys_tee_wrapper) diff --git a/arch/s390/kernel/vmlinux.lds.S b/arch/s390/kernel/vmlinux.lds.S index 9289face302..9f34bb54c05 100644 --- a/arch/s390/kernel/vmlinux.lds.S +++ b/arch/s390/kernel/vmlinux.lds.S @@ -58,9 +58,11 @@ SECTIONS . = ALIGN(4096); .data.page_aligned : { *(.data.idt) } - . = ALIGN(32); + . = ALIGN(256); .data.cacheline_aligned : { *(.data.cacheline_aligned) } + . = ALIGN(256); + .data.read_mostly : { *(.data.read_mostly) } _edata = .; /* End of data section */ . = ALIGN(8192); /* init_task */ diff --git a/arch/s390/mm/extmem.c b/arch/s390/mm/extmem.c index a9566bcab68..9b11e3e2090 100644 --- a/arch/s390/mm/extmem.c +++ b/arch/s390/mm/extmem.c @@ -192,6 +192,7 @@ query_segment_type (struct dcss_segment *seg) diag_cc = dcss_diag (DCSS_SEGEXT, qin, &dummy, &vmrc); if (diag_cc > 1) { + PRINT_WARN ("segment_type: diag returned error %ld\n", vmrc); rc = dcss_diag_translate_rc (vmrc); goto out_free; } @@ -553,7 +554,7 @@ segment_save(char *name) int endpfn = 0; char cmd1[160]; char cmd2[80]; - int i; + int i, response; if (!MACHINE_IS_VM) return; @@ -576,8 +577,20 @@ segment_save(char *name) segtype_string[seg->range[i].start & 0xff]); } sprintf(cmd2, "SAVESEG %s", name); - cpcmd(cmd1, NULL, 0, NULL); - cpcmd(cmd2, NULL, 0, NULL); + response = 0; + cpcmd(cmd1, NULL, 0, &response); + if (response) { + PRINT_ERR("segment_save: DEFSEG failed with response code %i\n", + response); + goto out; + } + cpcmd(cmd2, NULL, 0, &response); + if (response) { + PRINT_ERR("segment_save: SAVESEG failed with response code %i\n", + response); + goto out; + } +out: spin_unlock(&dcss_lock); } diff --git a/arch/sparc/kernel/systbls.S b/arch/sparc/kernel/systbls.S index db8faa75f94..6e1135cc03b 100644 --- a/arch/sparc/kernel/systbls.S +++ b/arch/sparc/kernel/systbls.S @@ -23,7 +23,7 @@ sys_call_table: /*10*/ .long sys_unlink, sunos_execv, sys_chdir, sys_chown16, sys_mknod /*15*/ .long sys_chmod, sys_lchown16, sparc_brk, sys_nis_syscall, sys_lseek /*20*/ .long sys_getpid, sys_capget, sys_capset, sys_setuid16, sys_getuid16 -/*25*/ .long sys_time, sys_ptrace, sys_alarm, sys_sigaltstack, sys_pause +/*25*/ .long sys_vmsplice, sys_ptrace, sys_alarm, sys_sigaltstack, sys_pause /*30*/ .long sys_utime, sys_lchown, sys_fchown, sys_access, sys_nice /*35*/ .long sys_chown, sys_sync, sys_kill, sys_newstat, sys_sendfile /*40*/ .long sys_newlstat, sys_dup, sys_pipe, sys_times, sys_getuid diff --git a/arch/sparc64/kernel/ptrace.c b/arch/sparc64/kernel/ptrace.c index 49e6dedd027..d31975e6d6f 100644 --- a/arch/sparc64/kernel/ptrace.c +++ b/arch/sparc64/kernel/ptrace.c @@ -653,7 +653,7 @@ asmlinkage void syscall_trace(struct pt_regs *regs, int syscall_exit_p) if (unlikely(tstate & (TSTATE_XCARRY | TSTATE_ICARRY))) result = AUDITSC_FAILURE; - audit_syscall_exit(current, result, regs->u_regs[UREG_I0]); + audit_syscall_exit(result, regs->u_regs[UREG_I0]); } if (!(current->ptrace & PT_PTRACED)) @@ -677,8 +677,7 @@ asmlinkage void syscall_trace(struct pt_regs *regs, int syscall_exit_p) out: if (unlikely(current->audit_context) && !syscall_exit_p) - audit_syscall_entry(current, - (test_thread_flag(TIF_32BIT) ? + audit_syscall_entry((test_thread_flag(TIF_32BIT) ? AUDIT_ARCH_SPARC : AUDIT_ARCH_SPARC64), regs->u_regs[UREG_G1], diff --git a/arch/sparc64/kernel/sys32.S b/arch/sparc64/kernel/sys32.S index f9b75760163..bdf1f4d02e3 100644 --- a/arch/sparc64/kernel/sys32.S +++ b/arch/sparc64/kernel/sys32.S @@ -139,6 +139,7 @@ SIGN3(sys32_ioprio_set, sys_ioprio_set, %o0, %o1, %o2) SIGN2(sys32_splice, sys_splice, %o0, %o1) SIGN2(sys32_sync_file_range, compat_sync_file_range, %o0, %o5) SIGN2(sys32_tee, sys_tee, %o0, %o1) +SIGN1(sys32_vmsplice, compat_sys_vmsplice, %o0) .globl sys32_mmap2 sys32_mmap2: diff --git a/arch/sparc64/kernel/systbls.S b/arch/sparc64/kernel/systbls.S index 62672cd92ec..d4b39cd3031 100644 --- a/arch/sparc64/kernel/systbls.S +++ b/arch/sparc64/kernel/systbls.S @@ -25,7 +25,7 @@ sys_call_table32: /*10*/ .word sys_unlink, sunos_execv, sys_chdir, sys32_chown16, sys32_mknod /*15*/ .word sys_chmod, sys32_lchown16, sparc_brk, sys32_perfctr, sys32_lseek /*20*/ .word sys_getpid, sys_capget, sys_capset, sys32_setuid16, sys32_getuid16 -/*25*/ .word compat_sys_time, sys_ptrace, sys_alarm, sys32_sigaltstack, sys32_pause +/*25*/ .word sys32_vmsplice, sys_ptrace, sys_alarm, sys32_sigaltstack, sys32_pause /*30*/ .word compat_sys_utime, sys_lchown, sys_fchown, sys32_access, sys32_nice .word sys_chown, sys_sync, sys32_kill, compat_sys_newstat, sys32_sendfile /*40*/ .word compat_sys_newlstat, sys_dup, sys_pipe, compat_sys_times, sys_getuid @@ -94,7 +94,7 @@ sys_call_table: /*10*/ .word sys_unlink, sys_nis_syscall, sys_chdir, sys_chown, sys_mknod /*15*/ .word sys_chmod, sys_lchown, sparc_brk, sys_perfctr, sys_lseek /*20*/ .word sys_getpid, sys_capget, sys_capset, sys_setuid, sys_getuid -/*25*/ .word sys_nis_syscall, sys_ptrace, sys_alarm, sys_sigaltstack, sys_nis_syscall +/*25*/ .word sys_vmsplice, sys_ptrace, sys_alarm, sys_sigaltstack, sys_nis_syscall /*30*/ .word sys_utime, sys_nis_syscall, sys_nis_syscall, sys_access, sys_nice .word sys_nis_syscall, sys_sync, sys_kill, sys_newstat, sys_sendfile64 /*40*/ .word sys_newlstat, sys_dup, sys_pipe, sys_times, sys_nis_syscall diff --git a/arch/sparc64/mm/tlb.c b/arch/sparc64/mm/tlb.c index a079cf42505..3f10fc921b0 100644 --- a/arch/sparc64/mm/tlb.c +++ b/arch/sparc64/mm/tlb.c @@ -8,6 +8,7 @@ #include <linux/percpu.h> #include <linux/mm.h> #include <linux/swap.h> +#include <linux/preempt.h> #include <asm/pgtable.h> #include <asm/pgalloc.h> @@ -24,6 +25,8 @@ void flush_tlb_pending(void) { struct mmu_gather *mp = &__get_cpu_var(mmu_gathers); + preempt_disable(); + if (mp->tlb_nr) { flush_tsb_user(mp); @@ -38,6 +41,8 @@ void flush_tlb_pending(void) } mp->tlb_nr = 0; } + + preempt_enable(); } void tlb_batch_add(struct mm_struct *mm, unsigned long vaddr, pte_t *ptep, pte_t orig) diff --git a/arch/um/Kconfig b/arch/um/Kconfig index 05fbb20636c..76e85bbaea5 100644 --- a/arch/um/Kconfig +++ b/arch/um/Kconfig @@ -57,20 +57,6 @@ config STATIC_LINK chroot, and you disable CONFIG_MODE_TT, you probably want to say Y here. -config HOST_2G_2G - bool "2G/2G host address space split" - default n - depends on MODE_TT - help - This is needed when the host on which you run has a 2G/2G memory - split, instead of the customary 3G/1G. - - Note that to enable such a host - configuration, which makes sense only in some cases, you need special - host patches. - - So, if you do not know what to do here, say 'N'. - config KERNEL_HALF_GIGS int "Kernel address space size (in .5G units)" default "1" diff --git a/arch/um/Kconfig.i386 b/arch/um/Kconfig.i386 index 85e6a55b3b5..f6eb72d117b 100644 --- a/arch/um/Kconfig.i386 +++ b/arch/um/Kconfig.i386 @@ -16,6 +16,19 @@ config SEMAPHORE_SLEEPERS bool default y +config HOST_2G_2G + bool "2G/2G host address space split" + default n + help + This is needed when the host on which you run has a 2G/2G memory + split, instead of the customary 3G/1G. + + Note that to enable such a host + configuration, which makes sense only in some cases, you need special + host patches. + + So, if you do not know what to do here, say 'N'. + config TOP_ADDR hex default 0xc0000000 if !HOST_2G_2G @@ -35,11 +48,13 @@ config 3_LEVEL_PGTABLES config STUB_CODE hex - default 0xbfffe000 + default 0xbfffe000 if !HOST_2G_2G + default 0x7fffe000 if HOST_2G_2G config STUB_DATA hex - default 0xbffff000 + default 0xbffff000 if !HOST_2G_2G + default 0x7ffff000 if HOST_2G_2G config STUB_START hex diff --git a/arch/um/Makefile b/arch/um/Makefile index a508e7a0289..f6ad832faf1 100644 --- a/arch/um/Makefile +++ b/arch/um/Makefile @@ -96,7 +96,8 @@ PHONY += linux all: linux linux: vmlinux - ln -f $< $@ + @echo ' LINK $@' + $(Q)ln -f $< $@ define archhelp echo '* linux - Binary kernel image (./linux) - for backward' @@ -117,6 +118,10 @@ prepare: $(ARCH_DIR)/include/kern_constants.h LINK-$(CONFIG_LD_SCRIPT_STATIC) += -static LINK-$(CONFIG_LD_SCRIPT_DYN) += -Wl,-rpath,/lib +CFLAGS_NO_HARDENING := $(call cc-option, -fno-PIC,) $(call cc-option, -fno-pic,) \ + $(call cc-option, -fno-stack-protector,) \ + $(call cc-option, -fno-stack-protector-all,) + CPP_MODE-$(CONFIG_MODE_TT) := -DMODE_TT CONFIG_KERNEL_STACK_ORDER ?= 2 STACK_SIZE := $(shell echo $$[ 4096 * (1 << $(CONFIG_KERNEL_STACK_ORDER)) ] ) @@ -203,8 +208,8 @@ endef $(ARCH_DIR)/include/uml-config.h : include/linux/autoconf.h $(call filechk,umlconfig) -$(ARCH_DIR)/user-offsets.s: $(ARCH_DIR)/sys-$(SUBARCH)/user-offsets.c - $(CC) $(USER_CFLAGS) -S -o $@ $< +$(ARCH_DIR)/sys-$(SUBARCH)/user-offsets.s: FORCE + $(Q)$(MAKE) $(build)=$(ARCH_DIR)/sys-$(SUBARCH) $@ define filechk_gen-asm-offsets (set -e; \ @@ -219,13 +224,11 @@ define filechk_gen-asm-offsets echo ""; ) endef -$(ARCH_DIR)/include/user_constants.h: $(ARCH_DIR)/user-offsets.s +$(ARCH_DIR)/include/user_constants.h: $(ARCH_DIR)/sys-$(SUBARCH)/user-offsets.s $(call filechk,gen-asm-offsets) -CLEAN_FILES += $(ARCH_DIR)/user-offsets.s - $(ARCH_DIR)/include/kern_constants.h: $(objtree)/$(ARCH_DIR)/include @echo ' SYMLINK $@' - $(Q) ln -sf ../../../include/asm-um/asm-offsets.h $@ + $(Q)ln -sf ../../../include/asm-um/asm-offsets.h $@ -export SUBARCH USER_CFLAGS OS +export SUBARCH USER_CFLAGS CFLAGS_NO_HARDENING OS diff --git a/arch/um/defconfig b/arch/um/defconfig index 80d30d19d75..402a74dc502 100644 --- a/arch/um/defconfig +++ b/arch/um/defconfig @@ -1,14 +1,13 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.12-rc6-mm1 -# Tue Jun 14 18:22:21 2005 +# Linux kernel version: 2.6.17-rc3 +# Fri Apr 28 09:31:20 2006 # CONFIG_GENERIC_HARDIRQS=y CONFIG_UML=y CONFIG_MMU=y -CONFIG_UID16=y -CONFIG_RWSEM_GENERIC_SPINLOCK=y CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_IRQ_RELEASE_METHOD=y # # UML-specific options @@ -16,8 +15,50 @@ CONFIG_GENERIC_CALIBRATE_DELAY=y # CONFIG_MODE_TT is not set # CONFIG_STATIC_LINK is not set CONFIG_MODE_SKAS=y + +# +# Host processor type and features +# +# CONFIG_M386 is not set +# CONFIG_M486 is not set +# CONFIG_M586 is not set +# CONFIG_M586TSC is not set +# CONFIG_M586MMX is not set +CONFIG_M686=y +# CONFIG_MPENTIUMII is not set +# CONFIG_MPENTIUMIII is not set +# CONFIG_MPENTIUMM is not set +# CONFIG_MPENTIUM4 is not set +# CONFIG_MK6 is not set +# CONFIG_MK7 is not set +# CONFIG_MK8 is not set +# CONFIG_MCRUSOE is not set +# CONFIG_MEFFICEON is not set +# CONFIG_MWINCHIPC6 is not set +# CONFIG_MWINCHIP2 is not set +# CONFIG_MWINCHIP3D is not set +# CONFIG_MGEODEGX1 is not set +# CONFIG_MGEODE_LX is not set +# CONFIG_MCYRIXIII is not set +# CONFIG_MVIAC3_2 is not set +# CONFIG_X86_GENERIC is not set +CONFIG_X86_CMPXCHG=y +CONFIG_X86_XADD=y +CONFIG_X86_L1_CACHE_SHIFT=5 +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_X86_PPRO_FENCE=y +CONFIG_X86_WP_WORKS_OK=y +CONFIG_X86_INVLPG=y +CONFIG_X86_BSWAP=y +CONFIG_X86_POPAD_OK=y +CONFIG_X86_CMPXCHG64=y +CONFIG_X86_GOOD_APIC=y +CONFIG_X86_USE_PPRO_CHECKSUM=y +CONFIG_X86_TSC=y CONFIG_UML_X86=y # CONFIG_64BIT is not set +CONFIG_SEMAPHORE_SLEEPERS=y +# CONFIG_HOST_2G_2G is not set CONFIG_TOP_ADDR=0xc0000000 # CONFIG_3_LEVEL_PGTABLES is not set CONFIG_STUB_CODE=0xbfffe000 @@ -25,22 +66,24 @@ CONFIG_STUB_DATA=0xbffff000 CONFIG_STUB_START=0xbfffe000 CONFIG_ARCH_HAS_SC_SIGNALS=y CONFIG_ARCH_REUSE_HOST_VSYSCALL_AREA=y +CONFIG_GENERIC_HWEIGHT=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_LD_SCRIPT_DYN=y CONFIG_NET=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=m # CONFIG_HOSTFS is not set +# CONFIG_HPPFS is not set CONFIG_MCONSOLE=y # CONFIG_MAGIC_SYSRQ is not set -# CONFIG_HOST_2G_2G is not set CONFIG_NEST_LEVEL=0 -CONFIG_KERNEL_HALF_GIGS=1 # CONFIG_HIGHMEM is not set CONFIG_KERNEL_STACK_ORDER=2 CONFIG_UML_REAL_TIME_CLOCK=y @@ -49,7 +92,6 @@ CONFIG_UML_REAL_TIME_CLOCK=y # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 @@ -57,6 +99,7 @@ CONFIG_INIT_ENV_ARG_LIMIT=32 # General setup # CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y CONFIG_POSIX_MQUEUE=y @@ -64,26 +107,28 @@ CONFIG_BSD_PROCESS_ACCT=y # CONFIG_BSD_PROCESS_ACCT_V3 is not set CONFIG_SYSCTL=y # CONFIG_AUDIT is not set -# CONFIG_HOTPLUG is not set -CONFIG_KOBJECT_UEVENT=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y +# CONFIG_RELAY is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_UID16=y +CONFIG_CC_OPTIMIZE_FOR_SIZE=y # CONFIG_EMBEDDED is not set CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set CONFIG_KALLSYMS_EXTRA_PASS=y +CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y +CONFIG_ELF_CORE=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 +CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set # # Loadable module support @@ -91,18 +136,43 @@ CONFIG_BASE_SMALL=0 CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_KMOD=y # -# Generic Driver Options +# Block layer # -CONFIG_STANDALONE=y -CONFIG_PREVENT_FIRMWARE_BUILD=y -# CONFIG_FW_LOADER is not set -# CONFIG_DEBUG_DRIVER is not set +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# Block devices +# +CONFIG_BLK_DEV_UBD=y +# CONFIG_BLK_DEV_UBD_SYNC is not set +CONFIG_BLK_DEV_COW_COMMON=y +# CONFIG_MMAPPER is not set +CONFIG_BLK_DEV_LOOP=m +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +CONFIG_BLK_DEV_NBD=m +# CONFIG_BLK_DEV_RAM is not set +# CONFIG_BLK_DEV_INITRD is not set +# CONFIG_ATA_OVER_ETH is not set # # Character Devices @@ -127,50 +197,23 @@ CONFIG_UML_SOUND=m CONFIG_SOUND=m CONFIG_HOSTAUDIO=m CONFIG_UML_RANDOM=y -# CONFIG_MMAPPER is not set - -# -# Block devices -# -CONFIG_BLK_DEV_UBD=y -CONFIG_BLK_DEV_UBD_SYNC=y -CONFIG_BLK_DEV_COW_COMMON=y -CONFIG_BLK_DEV_LOOP=m -# CONFIG_BLK_DEV_CRYPTOLOOP is not set -CONFIG_BLK_DEV_NBD=m -# CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 -CONFIG_INITRAMFS_SOURCE="" -# CONFIG_LBD is not set - -# -# IO Schedulers -# -CONFIG_IOSCHED_NOOP=y -CONFIG_IOSCHED_AS=y -CONFIG_IOSCHED_DEADLINE=y -CONFIG_IOSCHED_CFQ=y -# CONFIG_ATA_OVER_ETH is not set -CONFIG_NETDEVICES=y # -# UML Network Devices +# Generic Driver Options # -CONFIG_UML_NET=y -CONFIG_UML_NET_ETHERTAP=y -CONFIG_UML_NET_TUNTAP=y -CONFIG_UML_NET_SLIP=y -CONFIG_UML_NET_DAEMON=y -CONFIG_UML_NET_MCAST=y -CONFIG_UML_NET_SLIRP=y +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set # -# Networking support +# Networking # # # Networking options # +# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -178,6 +221,7 @@ CONFIG_UNIX=y CONFIG_INET=y # CONFIG_IP_MULTICAST is not set # CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y # CONFIG_IP_PNP is not set # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set @@ -186,27 +230,31 @@ CONFIG_INET=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set -CONFIG_IP_TCPDIAG=y -# CONFIG_IP_TCPDIAG_IPV6 is not set - -# -# TCP congestion control -# +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y -CONFIG_TCP_CONG_WESTWOOD=y -CONFIG_TCP_CONG_HTCP=y -# CONFIG_TCP_CONG_HSTCP is not set -# CONFIG_TCP_CONG_HYBLA is not set -# CONFIG_TCP_CONG_VEGAS is not set -# CONFIG_TCP_CONG_SCALABLE is not set # CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set # CONFIG_NETFILTER is not set # +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set @@ -224,27 +272,47 @@ CONFIG_TCP_CONG_HTCP=y # QoS and/or fair queueing # # CONFIG_NET_SCHED is not set -# CONFIG_NET_CLS_ROUTE is not set # # Network testing # # CONFIG_NET_PKTGEN is not set -# CONFIG_KGDBOE is not set -# CONFIG_NETPOLL is not set -# CONFIG_NETPOLL_RX is not set -# CONFIG_NETPOLL_TRAP is not set -# CONFIG_NET_POLL_CONTROLLER is not set # CONFIG_HAMRADIO is not set # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_IEEE80211 is not set + +# +# UML Network Devices +# +CONFIG_UML_NET=y +CONFIG_UML_NET_ETHERTAP=y +CONFIG_UML_NET_TUNTAP=y +CONFIG_UML_NET_SLIP=y +CONFIG_UML_NET_DAEMON=y +CONFIG_UML_NET_MCAST=y +# CONFIG_UML_NET_PCAP is not set +CONFIG_UML_NET_SLIRP=y + +# +# Network device support +# +CONFIG_NETDEVICES=y CONFIG_DUMMY=m # CONFIG_BONDING is not set # CONFIG_EQUALIZER is not set CONFIG_TUN=m # +# PHY device support +# + +# +# Wireless LAN (non-hamradio) +# +# CONFIG_NET_RADIO is not set + +# # Wan interfaces # # CONFIG_WAN is not set @@ -263,6 +331,13 @@ CONFIG_SLIP=m # CONFIG_SLIP_MODE_SLIP6 is not set # CONFIG_SHAPER is not set # CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set # # File systems @@ -274,17 +349,14 @@ CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set CONFIG_JBD=y # CONFIG_JBD_DEBUG is not set -# CONFIG_REISER4_FS is not set CONFIG_REISERFS_FS=y # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set # CONFIG_REISERFS_FS_XATTR is not set # CONFIG_JFS_FS is not set - -# -# XFS support -# +# CONFIG_FS_POSIX_ACL is not set # CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_ROMFS_FS is not set CONFIG_INOTIFY=y @@ -295,11 +367,6 @@ CONFIG_QUOTACTL=y CONFIG_DNOTIFY=y CONFIG_AUTOFS_FS=m CONFIG_AUTOFS4_FS=m - -# -# Caches -# -# CONFIG_FSCACHE is not set # CONFIG_FUSE_FS is not set # @@ -323,14 +390,10 @@ CONFIG_JOLIET=y CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_SYSFS=y -# CONFIG_DEVFS_FS is not set -# CONFIG_DEVPTS_FS_XATTR is not set CONFIG_TMPFS=y -# CONFIG_TMPFS_XATTR is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set -# CONFIG_RELAYFS_FS is not set # # Miscellaneous filesystems @@ -430,6 +493,7 @@ CONFIG_NLS_DEFAULT="iso8859-1" # Library routines # # CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set CONFIG_CRC32=m # CONFIG_LIBCRC32C is not set @@ -448,12 +512,18 @@ CONFIG_LOG_BUF_SHIFT=14 CONFIG_DETECT_SOFTLOCKUP=y # CONFIG_SCHEDSTATS is not set CONFIG_DEBUG_SLAB=y +# CONFIG_DEBUG_SLAB_LEAK is not set +# CONFIG_DEBUG_MUTEXES is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_KOBJECT is not set CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set CONFIG_FRAME_POINTER=y +# CONFIG_UNWIND_INFO is not set +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set # CONFIG_GPROF is not set # CONFIG_GCOV is not set # CONFIG_SYSCALL_DEBUG is not set diff --git a/arch/um/drivers/cow_user.c b/arch/um/drivers/cow_user.c index 6ab852bfcd3..0ec4052db9c 100644 --- a/arch/um/drivers/cow_user.c +++ b/arch/um/drivers/cow_user.c @@ -100,7 +100,7 @@ struct cow_header_v3_broken { __u32 alignment; __u32 cow_format; char backing_file[PATH_LEN_V3]; -} __attribute__((packed)); +}; /* COW format definitions - for now, we have only the usual COW bitmap */ #define COW_BITMAP 0 diff --git a/arch/um/kernel/irq.c b/arch/um/kernel/irq.c index c39ea3abeda..2ffda012385 100644 --- a/arch/um/kernel/irq.c +++ b/arch/um/kernel/irq.c @@ -89,16 +89,18 @@ void sigio_handler(int sig, union uml_pt_regs *regs) struct irq_fd *irq_fd; int n; - if(smp_sigio_handler()) return; - while(1){ + if (smp_sigio_handler()) + return; + + while (1) { n = os_waiting_for_events(active_fds); if (n <= 0) { if(n == -EINTR) continue; else break; } - for(irq_fd = active_fds; irq_fd != NULL; irq_fd = irq_fd->next){ - if(irq_fd->current_events != 0){ + for (irq_fd = active_fds; irq_fd != NULL; irq_fd = irq_fd->next) { + if (irq_fd->current_events != 0) { irq_fd->current_events = 0; do_IRQ(irq_fd->irq, regs); } @@ -110,19 +112,17 @@ void sigio_handler(int sig, union uml_pt_regs *regs) static void maybe_sigio_broken(int fd, int type) { - if(os_isatty(fd)){ - if((type == IRQ_WRITE) && !pty_output_sigio){ + if (os_isatty(fd)) { + if ((type == IRQ_WRITE) && !pty_output_sigio) { write_sigio_workaround(); add_sigio_fd(fd, 0); - } - else if((type == IRQ_READ) && !pty_close_sigio){ + } else if ((type == IRQ_READ) && !pty_close_sigio) { write_sigio_workaround(); add_sigio_fd(fd, 1); } } } - int activate_fd(int irq, int fd, int type, void *dev_id) { struct pollfd *tmp_pfd; @@ -132,16 +132,18 @@ int activate_fd(int irq, int fd, int type, void *dev_id) pid = os_getpid(); err = os_set_fd_async(fd, pid); - if(err < 0) + if (err < 0) goto out; new_fd = um_kmalloc(sizeof(*new_fd)); err = -ENOMEM; - if(new_fd == NULL) + if (new_fd == NULL) goto out; - if(type == IRQ_READ) events = UM_POLLIN | UM_POLLPRI; - else events = UM_POLLOUT; + if (type == IRQ_READ) + events = UM_POLLIN | UM_POLLPRI; + else + events = UM_POLLOUT; *new_fd = ((struct irq_fd) { .next = NULL, .id = dev_id, .fd = fd, @@ -165,8 +167,8 @@ int activate_fd(int irq, int fd, int type, void *dev_id) * a semaphore. */ flags = irq_lock(); - for(irq_fd = active_fds; irq_fd != NULL; irq_fd = irq_fd->next){ - if((irq_fd->fd == fd) && (irq_fd->type == type)){ + for (irq_fd = active_fds; irq_fd != NULL; irq_fd = irq_fd->next) { + if ((irq_fd->fd == fd) && (irq_fd->type == type)) { printk("Registering fd %d twice\n", fd); printk("Irqs : %d, %d\n", irq_fd->irq, irq); printk("Ids : 0x%p, 0x%p\n", irq_fd->id, dev_id); @@ -175,13 +177,13 @@ int activate_fd(int irq, int fd, int type, void *dev_id) } /*-------------*/ - if(type == IRQ_WRITE) + if (type == IRQ_WRITE) fd = -1; tmp_pfd = NULL; n = 0; - while(1){ + while (1) { n = os_create_pollfd(fd, events, tmp_pfd, n); if (n == 0) break; @@ -198,10 +200,8 @@ int activate_fd(int irq, int fd, int type, void *dev_id) * then we free the buffer tmp_fds and try again. */ irq_unlock(flags); - if (tmp_pfd != NULL) { - kfree(tmp_pfd); - tmp_pfd = NULL; - } + kfree(tmp_pfd); + tmp_pfd = NULL; tmp_pfd = um_kmalloc(n); if (tmp_pfd == NULL) @@ -249,7 +249,7 @@ static int same_irq_and_dev(struct irq_fd *irq, void *d) { struct irq_and_dev *data = d; - return((irq->irq == data->irq) && (irq->id == data->dev)); + return ((irq->irq == data->irq) && (irq->id == data->dev)); } void free_irq_by_irq_and_dev(unsigned int irq, void *dev) @@ -262,7 +262,7 @@ void free_irq_by_irq_and_dev(unsigned int irq, void *dev) static int same_fd(struct irq_fd *irq, void *fd) { - return(irq->fd == *((int *) fd)); + return (irq->fd == *((int *)fd)); } void free_irq_by_fd(int fd) @@ -276,16 +276,17 @@ static struct irq_fd *find_irq_by_fd(int fd, int irqnum, int *index_out) int i = 0; int fdi; - for(irq=active_fds; irq != NULL; irq = irq->next){ - if((irq->fd == fd) && (irq->irq == irqnum)) break; + for (irq = active_fds; irq != NULL; irq = irq->next) { + if ((irq->fd == fd) && (irq->irq == irqnum)) + break; i++; } - if(irq == NULL){ + if (irq == NULL) { printk("find_irq_by_fd doesn't have descriptor %d\n", fd); goto out; } fdi = os_get_pollfd(i); - if((fdi != -1) && (fdi != fd)){ + if ((fdi != -1) && (fdi != fd)) { printk("find_irq_by_fd - mismatch between active_fds and " "pollfds, fd %d vs %d, need %d\n", irq->fd, fdi, fd); @@ -294,7 +295,7 @@ static struct irq_fd *find_irq_by_fd(int fd, int irqnum, int *index_out) } *index_out = i; out: - return(irq); + return irq; } void reactivate_fd(int fd, int irqnum) @@ -305,7 +306,7 @@ void reactivate_fd(int fd, int irqnum) flags = irq_lock(); irq = find_irq_by_fd(fd, irqnum, &i); - if(irq == NULL){ + if (irq == NULL) { irq_unlock(flags); return; } @@ -326,7 +327,7 @@ void deactivate_fd(int fd, int irqnum) flags = irq_lock(); irq = find_irq_by_fd(fd, irqnum, &i); - if(irq == NULL) + if (irq == NULL) goto out; os_set_pollfd(i, -1); out: @@ -338,15 +339,15 @@ int deactivate_all_fds(void) struct irq_fd *irq; int err; - for(irq=active_fds;irq != NULL;irq = irq->next){ + for (irq = active_fds; irq != NULL; irq = irq->next) { err = os_clear_fd_async(irq->fd); - if(err) - return(err); + if (err) + return err; } /* If there is a signal already queued, after unblocking ignore it */ os_set_ioignore(); - return(0); + return 0; } void forward_interrupts(int pid) @@ -356,9 +357,9 @@ void forward_interrupts(int pid) int err; flags = irq_lock(); - for(irq=active_fds;irq != NULL;irq = irq->next){ + for (irq = active_fds; irq != NULL; irq = irq->next) { err = os_set_owner(irq->fd, pid); - if(err < 0){ + if (err < 0) { /* XXX Just remove the irq rather than * print out an infinite stream of these */ @@ -379,7 +380,7 @@ void forward_interrupts(int pid) unsigned int do_IRQ(int irq, union uml_pt_regs *regs) { irq_enter(); - __do_IRQ(irq, (struct pt_regs *) regs); + __do_IRQ(irq, (struct pt_regs *)regs); irq_exit(); return 1; } @@ -392,12 +393,12 @@ int um_request_irq(unsigned int irq, int fd, int type, int err; err = request_irq(irq, handler, irqflags, devname, dev_id); - if(err) - return(err); + if (err) + return err; - if(fd != -1) + if (fd != -1) err = activate_fd(irq, fd, type, dev_id); - return(err); + return err; } EXPORT_SYMBOL(um_request_irq); EXPORT_SYMBOL(reactivate_fd); @@ -409,7 +410,7 @@ unsigned long irq_lock(void) unsigned long flags; spin_lock_irqsave(&irq_spinlock, flags); - return(flags); + return flags; } void irq_unlock(unsigned long flags) @@ -452,7 +453,7 @@ void __init init_IRQ(void) irq_desc[TIMER_IRQ].depth = 1; irq_desc[TIMER_IRQ].handler = &SIGVTALRM_irq_type; enable_irq(TIMER_IRQ); - for(i=1;i<NR_IRQS;i++){ + for (i = 1; i < NR_IRQS; i++) { irq_desc[i].status = IRQ_DISABLED; irq_desc[i].action = NULL; irq_desc[i].depth = 1; @@ -467,7 +468,7 @@ int init_aio_irq(int irq, char *name, irqreturn_t (*handler)(int, void *, int fds[2], err; err = os_pipe(fds, 1, 1); - if(err){ + if (err) { printk("init_aio_irq - os_pipe failed, err = %d\n", -err); goto out; } @@ -475,7 +476,7 @@ int init_aio_irq(int irq, char *name, irqreturn_t (*handler)(int, void *, err = um_request_irq(irq, fds[0], IRQ_READ, handler, SA_INTERRUPT | SA_SAMPLE_RANDOM, name, (void *) (long) fds[0]); - if(err){ + if (err) { printk("init_aio_irq - : um_request_irq failed, err = %d\n", err); goto out_close; @@ -488,5 +489,5 @@ int init_aio_irq(int irq, char *name, irqreturn_t (*handler)(int, void *, os_close_file(fds[0]); os_close_file(fds[1]); out: - return(err); + return err; } diff --git a/arch/um/kernel/physmem.c b/arch/um/kernel/physmem.c index 0500800df1c..fc0f0b085ca 100644 --- a/arch/um/kernel/physmem.c +++ b/arch/um/kernel/physmem.c @@ -407,6 +407,8 @@ unsigned long find_iomem(char *driver, unsigned long *len_out) *len_out = region->size; return(region->virt); } + + region = region->next; } return(0); diff --git a/arch/um/kernel/ptrace.c b/arch/um/kernel/ptrace.c index 60d2eda995c..9a77fb3c269 100644 --- a/arch/um/kernel/ptrace.c +++ b/arch/um/kernel/ptrace.c @@ -275,15 +275,13 @@ void syscall_trace(union uml_pt_regs *regs, int entryexit) if (unlikely(current->audit_context)) { if (!entryexit) - audit_syscall_entry(current, - HOST_AUDIT_ARCH, + audit_syscall_entry(HOST_AUDIT_ARCH, UPT_SYSCALL_NR(regs), UPT_SYSCALL_ARG1(regs), UPT_SYSCALL_ARG2(regs), UPT_SYSCALL_ARG3(regs), UPT_SYSCALL_ARG4(regs)); - else audit_syscall_exit(current, - AUDITSC_RESULT(UPT_SYSCALL_RET(regs)), + else audit_syscall_exit(AUDITSC_RESULT(UPT_SYSCALL_RET(regs)), UPT_SYSCALL_RET(regs)); } diff --git a/arch/um/kernel/skas/Makefile b/arch/um/kernel/skas/Makefile index 57181a920d4..ea3a8e409a6 100644 --- a/arch/um/kernel/skas/Makefile +++ b/arch/um/kernel/skas/Makefile @@ -6,9 +6,11 @@ obj-y := clone.o exec_kern.o mem.o mmu.o process_kern.o \ syscall.o tlb.o uaccess.o -USER_OBJS := clone.o +# clone.o is in the stub, so it can't be built with profiling +# GCC hardened also auto-enables -fpic, but we need %ebx so it can't work -> +# disable it -include arch/um/scripts/Makefile.rules +CFLAGS_clone.o := $(CFLAGS_NO_HARDENING) +UNPROFILE_OBJS := clone.o -# clone.o is in the stub, so it can't be built with profiling -$(obj)/clone.o : c_flags = -Wp,-MD,$(depfile) $(call unprofile,$(USER_CFLAGS)) +include arch/um/scripts/Makefile.rules diff --git a/arch/um/kernel/time_kern.c b/arch/um/kernel/time_kern.c index 3c7626cdba4..528cf623f8b 100644 --- a/arch/um/kernel/time_kern.c +++ b/arch/um/kernel/time_kern.c @@ -209,4 +209,4 @@ int __init timer_init(void) return(0); } -__initcall(timer_init); +arch_initcall(timer_init); diff --git a/arch/um/os-Linux/file.c b/arch/um/os-Linux/file.c index 3bd10deea28..09251338d99 100644 --- a/arch/um/os-Linux/file.c +++ b/arch/um/os-Linux/file.c @@ -171,7 +171,7 @@ int os_sigio_async(int master, int slave) flags = fcntl(master, F_GETFL); if(flags < 0) - return errno; + return -errno; if((fcntl(master, F_SETFL, flags | O_NONBLOCK | O_ASYNC) < 0) || (fcntl(master, F_SETOWN, os_getpid()) < 0)) diff --git a/arch/um/os-Linux/irq.c b/arch/um/os-Linux/irq.c index e599be423da..3788d4568d3 100644 --- a/arch/um/os-Linux/irq.c +++ b/arch/um/os-Linux/irq.c @@ -29,21 +29,21 @@ int os_waiting_for_events(struct irq_fd *active_fds) int i, n, err; n = poll(pollfds, pollfds_num, 0); - if(n < 0){ + if (n < 0) { err = -errno; - if(errno != EINTR) + if (errno != EINTR) printk("sigio_handler: os_waiting_for_events:" " poll returned %d, errno = %d\n", n, errno); return err; } - if(n == 0) + if (n == 0) return 0; irq_fd = active_fds; - for(i = 0; i < pollfds_num; i++){ - if(pollfds[i].revents != 0){ + for (i = 0; i < pollfds_num; i++) { + if (pollfds[i].revents != 0) { irq_fd->current_events = pollfds[i].revents; pollfds[i].fd = -1; } @@ -54,7 +54,7 @@ int os_waiting_for_events(struct irq_fd *active_fds) int os_isatty(int fd) { - return(isatty(fd)); + return isatty(fd); } int os_create_pollfd(int fd, int events, void *tmp_pfd, int size_tmpfds) @@ -65,7 +65,7 @@ int os_create_pollfd(int fd, int events, void *tmp_pfd, int size_tmpfds) return((pollfds_size + 1) * sizeof(pollfds[0])); } - if(pollfds != NULL){ + if (pollfds != NULL) { memcpy(tmp_pfd, pollfds, sizeof(pollfds[0]) * pollfds_size); /* remove old pollfds */ @@ -73,18 +73,15 @@ int os_create_pollfd(int fd, int events, void *tmp_pfd, int size_tmpfds) } pollfds = tmp_pfd; pollfds_size++; - } else { - /* remove not used tmp_pfd */ - if (tmp_pfd != NULL) - kfree(tmp_pfd); - } + } else + kfree(tmp_pfd); /* remove not used tmp_pfd */ - pollfds[pollfds_num] = ((struct pollfd) { .fd = fd, - .events = events, - .revents = 0 }); + pollfds[pollfds_num] = ((struct pollfd) { .fd = fd, + .events = events, + .revents = 0 }); pollfds_num++; - return(0); + return 0; } void os_free_irq_by_cb(int (*test)(struct irq_fd *, void *), void *arg, @@ -94,11 +91,11 @@ void os_free_irq_by_cb(int (*test)(struct irq_fd *, void *), void *arg, int i = 0; prev = &active_fds; - while(*prev != NULL){ - if((*test)(*prev, arg)){ + while (*prev != NULL) { + if ((*test)(*prev, arg)) { struct irq_fd *old_fd = *prev; - if((pollfds[i].fd != -1) && - (pollfds[i].fd != (*prev)->fd)){ + if ((pollfds[i].fd != -1) && + (pollfds[i].fd != (*prev)->fd)) { printk("os_free_irq_by_cb - mismatch between " "active_fds and pollfds, fd %d vs %d\n", (*prev)->fd, pollfds[i].fd); @@ -110,7 +107,6 @@ void os_free_irq_by_cb(int (*test)(struct irq_fd *, void *), void *arg, /* This moves the *whole* array after pollfds[i] * (though it doesn't spot as such)! */ - memmove(&pollfds[i], &pollfds[i + 1], (pollfds_num - i) * sizeof(pollfds[0])); if(*last_irq_ptr2 == &old_fd->next) @@ -129,10 +125,9 @@ void os_free_irq_by_cb(int (*test)(struct irq_fd *, void *), void *arg, return; } - int os_get_pollfd(int i) { - return(pollfds[i].fd); + return pollfds[i].fd; } void os_set_pollfd(int i, int fd) @@ -151,8 +146,10 @@ void init_irq_signals(int on_sigstack) int flags; flags = on_sigstack ? SA_ONSTACK : 0; - if(timer_irq_inited) h = (__sighandler_t) alarm_handler; - else h = boot_timer_handler; + if (timer_irq_inited) + h = (__sighandler_t)alarm_handler; + else + h = boot_timer_handler; set_handler(SIGVTALRM, h, flags | SA_RESTART, SIGUSR1, SIGIO, SIGWINCH, SIGALRM, -1); diff --git a/arch/um/os-Linux/main.c b/arch/um/os-Linux/main.c index 2878e89a674..3a0ac38e978 100644 --- a/arch/um/os-Linux/main.c +++ b/arch/um/os-Linux/main.c @@ -74,6 +74,34 @@ static void last_ditch_exit(int sig) exit(1); } +#define UML_LIB_PATH ":/usr/lib/uml" + +static void setup_env_path(void) +{ + char *new_path = NULL; + char *old_path = NULL; + int path_len = 0; + + old_path = getenv("PATH"); + /* if no PATH variable is set or it has an empty value + * just use the default + /usr/lib/uml + */ + if (!old_path || (path_len = strlen(old_path)) == 0) { + putenv("PATH=:/bin:/usr/bin/" UML_LIB_PATH); + return; + } + + /* append /usr/lib/uml to the existing path */ + path_len += strlen("PATH=" UML_LIB_PATH) + 1; + new_path = malloc(path_len); + if (!new_path) { + perror("coudn't malloc to set a new PATH"); + return; + } + snprintf(new_path, path_len, "PATH=%s" UML_LIB_PATH, old_path); + putenv(new_path); +} + extern int uml_exitcode; extern void scan_elf_aux( char **envp); @@ -114,6 +142,8 @@ int main(int argc, char **argv, char **envp) set_stklim(); + setup_env_path(); + new_argv = malloc((argc + 1) * sizeof(char *)); if(new_argv == NULL){ perror("Mallocing argv"); diff --git a/arch/um/os-Linux/process.c b/arch/um/os-Linux/process.c index 3505f44f8a2..233be2f4f8c 100644 --- a/arch/um/os-Linux/process.c +++ b/arch/um/os-Linux/process.c @@ -206,29 +206,36 @@ int os_drop_memory(void *addr, int length) int can_drop_memory(void) { void *addr; - int fd; + int fd, ok = 0; printk("Checking host MADV_REMOVE support..."); fd = create_mem_file(UM_KERN_PAGE_SIZE); if(fd < 0){ printk("Creating test memory file failed, err = %d\n", -fd); - return 0; + goto out; } addr = mmap64(NULL, UM_KERN_PAGE_SIZE, PROT_READ | PROT_WRITE, MAP_SHARED, fd, 0); if(addr == MAP_FAILED){ printk("Mapping test memory file failed, err = %d\n", -errno); - return 0; + goto out_close; } if(madvise(addr, UM_KERN_PAGE_SIZE, MADV_REMOVE) != 0){ printk("MADV_REMOVE failed, err = %d\n", -errno); - return 0; + goto out_unmap; } printk("OK\n"); - return 1; + ok = 1; + +out_unmap: + munmap(addr, UM_KERN_PAGE_SIZE); +out_close: + close(fd); +out: + return ok; } void init_new_thread_stack(void *sig_stack, void (*usr1_handler)(int)) diff --git a/arch/um/os-Linux/skas/process.c b/arch/um/os-Linux/skas/process.c index 0776bc18ca8..bd89c6b99d5 100644 --- a/arch/um/os-Linux/skas/process.c +++ b/arch/um/os-Linux/skas/process.c @@ -344,12 +344,12 @@ int copy_context_skas0(unsigned long new_stack, int pid) err = ptrace_setregs(pid, regs); if(err < 0) panic("copy_context_skas0 : PTRACE_SETREGS failed, " - "pid = %d, errno = %d\n", pid, errno); + "pid = %d, errno = %d\n", pid, -err); err = ptrace_setfpregs(pid, fp_regs); if(err < 0) panic("copy_context_skas0 : PTRACE_SETFPREGS failed, " - "pid = %d, errno = %d\n", pid, errno); + "pid = %d, errno = %d\n", pid, -err); /* set a well known return code for detection of child write failure */ child_data->err = 12345678; @@ -362,7 +362,7 @@ int copy_context_skas0(unsigned long new_stack, int pid) pid = data->err; if(pid < 0) panic("copy_context_skas0 - stub-parent reports error %d\n", - pid); + -pid); /* Wait, until child has finished too: read child's result from * child's stack and check it. diff --git a/arch/um/os-Linux/sys-i386/registers.c b/arch/um/os-Linux/sys-i386/registers.c index 7a6f6b99cef..516f66dd87e 100644 --- a/arch/um/os-Linux/sys-i386/registers.c +++ b/arch/um/os-Linux/sys-i386/registers.c @@ -104,7 +104,7 @@ void init_registers(int pid) err = ptrace(PTRACE_GETREGS, pid, 0, exec_regs); if(err) panic("check_ptrace : PTRACE_GETREGS failed, errno = %d", - err); + errno); errno = 0; err = ptrace(PTRACE_GETFPXREGS, pid, 0, exec_fpx_regs); @@ -119,7 +119,7 @@ void init_registers(int pid) err = ptrace(PTRACE_GETFPREGS, pid, 0, exec_fp_regs); if(err) panic("check_ptrace : PTRACE_GETFPREGS failed, errno = %d", - err); + errno); } void get_safe_registers(unsigned long *regs, unsigned long *fp_regs) diff --git a/arch/um/os-Linux/sys-x86_64/registers.c b/arch/um/os-Linux/sys-x86_64/registers.c index 001941fa1a1..becd898d939 100644 --- a/arch/um/os-Linux/sys-x86_64/registers.c +++ b/arch/um/os-Linux/sys-x86_64/registers.c @@ -62,12 +62,12 @@ void init_registers(int pid) err = ptrace(PTRACE_GETREGS, pid, 0, exec_regs); if(err) panic("check_ptrace : PTRACE_GETREGS failed, errno = %d", - err); + errno); err = ptrace(PTRACE_GETFPREGS, pid, 0, exec_fp_regs); if(err) panic("check_ptrace : PTRACE_GETFPREGS failed, errno = %d", - err); + errno); } void get_safe_registers(unsigned long *regs, unsigned long *fp_regs) diff --git a/arch/um/os-Linux/umid.c b/arch/um/os-Linux/umid.c index 34bfc1bb9e3..362db059fe3 100644 --- a/arch/um/os-Linux/umid.c +++ b/arch/um/os-Linux/umid.c @@ -178,14 +178,14 @@ static void __init create_pid_file(void) fd = open(file, O_RDWR | O_CREAT | O_EXCL, 0644); if(fd < 0){ printk("Open of machine pid file \"%s\" failed: %s\n", - file, strerror(-fd)); + file, strerror(errno)); return; } snprintf(pid, sizeof(pid), "%d\n", getpid()); n = write(fd, pid, strlen(pid)); if(n != strlen(pid)) - printk("Write of pid file failed - err = %d\n", -n); + printk("Write of pid file failed - err = %d\n", errno); close(fd); } diff --git a/arch/um/os-Linux/user_syms.c b/arch/um/os-Linux/user_syms.c index 2598158e1f5..3f33165ada6 100644 --- a/arch/um/os-Linux/user_syms.c +++ b/arch/um/os-Linux/user_syms.c @@ -96,6 +96,13 @@ EXPORT_SYMBOL_PROTO(getuid); EXPORT_SYMBOL_PROTO(fsync); EXPORT_SYMBOL_PROTO(fdatasync); +/* Export symbols used by GCC for the stack protector. */ +extern void __stack_smash_handler(void *) __attribute__((weak)); +EXPORT_SYMBOL(__stack_smash_handler); + +extern long __guard __attribute__((weak)); +EXPORT_SYMBOL(__guard); + /* * Overrides for Emacs so that we follow Linus's tabbing style. * Emacs will notice this stuff at the end of the file and automatically diff --git a/arch/um/scripts/Makefile.rules b/arch/um/scripts/Makefile.rules index 5e7a9c310aa..1347dc6d521 100644 --- a/arch/um/scripts/Makefile.rules +++ b/arch/um/scripts/Makefile.rules @@ -7,11 +7,19 @@ USER_SINGLE_OBJS := \ USER_OBJS += $(filter %_user.o,$(obj-y) $(obj-m) $(USER_SINGLE_OBJS)) USER_OBJS := $(foreach file,$(USER_OBJS),$(obj)/$(file)) -$(USER_OBJS) $(USER_OBJS:.o=.i) $(USER_OBJS:.o=.s) $(USER_OBJS:.o=.lst): \ - c_flags = -Wp,-MD,$(depfile) $(USER_CFLAGS) $(CFLAGS_$(notdir $@)) +$(USER_OBJS:.o=.%): \ + c_flags = -Wp,-MD,$(depfile) $(USER_CFLAGS) $(CFLAGS_$(*F).o) $(USER_OBJS) : CHECKFLAGS := -D__linux__ -Dlinux -D__STDC__ \ -Dunix -D__unix__ -D__$(SUBARCH)__ +# These are like USER_OBJS but filter USER_CFLAGS through unprofile instead of +# using it directly. +UNPROFILE_OBJS := $(foreach file,$(UNPROFILE_OBJS),$(obj)/$(file)) + +$(UNPROFILE_OBJS:.o=.%): \ + c_flags = -Wp,-MD,$(depfile) $(call unprofile,$(USER_CFLAGS)) $(CFLAGS_$(*F).o) +$(UNPROFILE_OBJS) : CHECKFLAGS := -D__linux__ -Dlinux -D__STDC__ \ + -Dunix -D__unix__ -D__$(SUBARCH)__ # The stubs and unmap.o can't try to call mcount or update basic block data define unprofile diff --git a/arch/um/sys-i386/Makefile b/arch/um/sys-i386/Makefile index 98b20b7bba4..374d61a1943 100644 --- a/arch/um/sys-i386/Makefile +++ b/arch/um/sys-i386/Makefile @@ -8,11 +8,16 @@ subarch-obj-y = lib/bitops.o kernel/semaphore.o subarch-obj-$(CONFIG_HIGHMEM) += mm/highmem.o subarch-obj-$(CONFIG_MODULES) += kernel/module.o -USER_OBJS := bugs.o ptrace_user.o sigcontext.o fault.o stub_segv.o +USER_OBJS := bugs.o ptrace_user.o sigcontext.o fault.o -include arch/um/scripts/Makefile.rules +USER_OBJS += user-offsets.s +extra-y += user-offsets.s extra-$(CONFIG_MODE_TT) += unmap.o -$(obj)/stub_segv.o $(obj)/unmap.o: \ - _c_flags = $(call unprofile,$(CFLAGS)) +UNPROFILE_OBJS := stub_segv.o +CFLAGS_stub_segv.o := $(CFLAGS_NO_HARDENING) + +include arch/um/scripts/Makefile.rules + +$(obj)/unmap.%: _c_flags = $(call unprofile,$(CFLAGS)) diff --git a/arch/um/sys-x86_64/Makefile b/arch/um/sys-x86_64/Makefile index b5fc22babdd..c19794d435d 100644 --- a/arch/um/sys-x86_64/Makefile +++ b/arch/um/sys-x86_64/Makefile @@ -16,11 +16,16 @@ subarch-obj-$(CONFIG_MODULES) += kernel/module.o ldt-y = ../sys-i386/ldt.o -USER_OBJS := ptrace_user.o sigcontext.o stub_segv.o +USER_OBJS := ptrace_user.o sigcontext.o -include arch/um/scripts/Makefile.rules +USER_OBJS += user-offsets.s +extra-y += user-offsets.s extra-$(CONFIG_MODE_TT) += unmap.o -$(obj)/stub_segv.o $(obj)/unmap.o: \ - _c_flags = $(call unprofile,$(CFLAGS)) +UNPROFILE_OBJS := stub_segv.o +CFLAGS_stub_segv.o := $(CFLAGS_NO_HARDENING) + +include arch/um/scripts/Makefile.rules + +$(obj)/unmap.%: _c_flags = $(call unprofile,$(CFLAGS)) diff --git a/arch/x86_64/ia32/ia32entry.S b/arch/x86_64/ia32/ia32entry.S index 57fc37e0fb9..5a92fed2d1d 100644 --- a/arch/x86_64/ia32/ia32entry.S +++ b/arch/x86_64/ia32/ia32entry.S @@ -695,4 +695,5 @@ ia32_sys_call_table: .quad sys_splice .quad sys_sync_file_range .quad sys_tee + .quad compat_sys_vmsplice ia32_syscall_end: diff --git a/arch/x86_64/kernel/e820.c b/arch/x86_64/kernel/e820.c index 62776c07cff..222b5b46d2b 100644 --- a/arch/x86_64/kernel/e820.c +++ b/arch/x86_64/kernel/e820.c @@ -76,6 +76,12 @@ static inline int bad_addr(unsigned long *addrp, unsigned long size) *addrp = __pa_symbol(&_end); return 1; } + + if (last >= ebda_addr && addr < ebda_addr + ebda_size) { + *addrp = ebda_addr + ebda_size; + return 1; + } + /* XXX ramdisk image here? */ return 0; } diff --git a/arch/x86_64/kernel/io_apic.c b/arch/x86_64/kernel/io_apic.c index 77b4c608cca..0de3ea93883 100644 --- a/arch/x86_64/kernel/io_apic.c +++ b/arch/x86_64/kernel/io_apic.c @@ -1777,6 +1777,8 @@ static inline void unlock_ExtINT_logic(void) spin_unlock_irqrestore(&ioapic_lock, flags); } +int timer_uses_ioapic_pin_0; + /* * This code may look a bit paranoid, but it's supposed to cooperate with * a wide range of boards and BIOS bugs. Fortunately only the timer IRQ @@ -1814,6 +1816,9 @@ static inline void check_timer(void) pin2 = ioapic_i8259.pin; apic2 = ioapic_i8259.apic; + if (pin1 == 0) + timer_uses_ioapic_pin_0 = 1; + apic_printk(APIC_VERBOSE,KERN_INFO "..TIMER: vector=0x%02X apic1=%d pin1=%d apic2=%d pin2=%d\n", vector, apic1, pin1, apic2, pin2); diff --git a/arch/x86_64/kernel/mpparse.c b/arch/x86_64/kernel/mpparse.c index b17cf3eba35..083da7e606b 100644 --- a/arch/x86_64/kernel/mpparse.c +++ b/arch/x86_64/kernel/mpparse.c @@ -968,7 +968,17 @@ int mp_register_gsi(u32 gsi, int triggering, int polarity) */ int irq = gsi; if (gsi < MAX_GSI_NUM) { - if (gsi > 15) + /* + * Retain the VIA chipset work-around (gsi > 15), but + * avoid a problem where the 8254 timer (IRQ0) is setup + * via an override (so it's not on pin 0 of the ioapic), + * and at the same time, the pin 0 interrupt is a PCI + * type. The gsi > 15 test could cause these two pins + * to be shared as IRQ0, and they are not shareable. + * So test for this condition, and if necessary, avoid + * the pin collision. + */ + if (gsi > 15 || (gsi == 0 && !timer_uses_ioapic_pin_0)) gsi = pci_irq++; /* * Don't assign IRQ used by ACPI SCI diff --git a/arch/x86_64/kernel/pci-gart.c b/arch/x86_64/kernel/pci-gart.c index 9d3d76c85ae..2480d3f08a4 100644 --- a/arch/x86_64/kernel/pci-gart.c +++ b/arch/x86_64/kernel/pci-gart.c @@ -639,6 +639,14 @@ static int __init pci_iommu_init(void) return -1; } + i = 0; + for_all_nb(dev) + i++; + if (i > MAX_NB) { + printk(KERN_ERR "PCI-GART: Too many northbridges (%ld). Disabled\n", i); + return -1; + } + printk(KERN_INFO "PCI-DMA: using GART IOMMU.\n"); aper_size = info.aper_size * 1024 * 1024; iommu_size = check_iommu_size(info.aper_base, aper_size); diff --git a/arch/x86_64/kernel/ptrace.c b/arch/x86_64/kernel/ptrace.c index da8e7903d81..2d50024c9f3 100644 --- a/arch/x86_64/kernel/ptrace.c +++ b/arch/x86_64/kernel/ptrace.c @@ -600,12 +600,12 @@ asmlinkage void syscall_trace_enter(struct pt_regs *regs) if (unlikely(current->audit_context)) { if (test_thread_flag(TIF_IA32)) { - audit_syscall_entry(current, AUDIT_ARCH_I386, + audit_syscall_entry(AUDIT_ARCH_I386, regs->orig_rax, regs->rbx, regs->rcx, regs->rdx, regs->rsi); } else { - audit_syscall_entry(current, AUDIT_ARCH_X86_64, + audit_syscall_entry(AUDIT_ARCH_X86_64, regs->orig_rax, regs->rdi, regs->rsi, regs->rdx, regs->r10); @@ -616,7 +616,7 @@ asmlinkage void syscall_trace_enter(struct pt_regs *regs) asmlinkage void syscall_trace_leave(struct pt_regs *regs) { if (unlikely(current->audit_context)) - audit_syscall_exit(current, AUDITSC_RESULT(regs->rax), regs->rax); + audit_syscall_exit(AUDITSC_RESULT(regs->rax), regs->rax); if ((test_thread_flag(TIF_SYSCALL_TRACE) || test_thread_flag(TIF_SINGLESTEP)) diff --git a/arch/x86_64/kernel/setup.c b/arch/x86_64/kernel/setup.c index 759070c8275..f0870bef24d 100644 --- a/arch/x86_64/kernel/setup.c +++ b/arch/x86_64/kernel/setup.c @@ -571,17 +571,28 @@ static inline void copy_edd(void) #endif #define EBDA_ADDR_POINTER 0x40E -static void __init reserve_ebda_region(void) + +unsigned __initdata ebda_addr; +unsigned __initdata ebda_size; + +static void discover_ebda(void) { - unsigned int addr; - /** + /* * there is a real-mode segmented pointer pointing to the * 4K EBDA area at 0x40E */ - addr = *(unsigned short *)phys_to_virt(EBDA_ADDR_POINTER); - addr <<= 4; - if (addr) - reserve_bootmem_generic(addr, PAGE_SIZE); + ebda_addr = *(unsigned short *)EBDA_ADDR_POINTER; + ebda_addr <<= 4; + + ebda_size = *(unsigned short *)(unsigned long)ebda_addr; + + /* Round EBDA up to pages */ + if (ebda_size == 0) + ebda_size = 1; + ebda_size <<= 10; + ebda_size = round_up(ebda_size + (ebda_addr & ~PAGE_MASK), PAGE_SIZE); + if (ebda_size > 64*1024) + ebda_size = 64*1024; } void __init setup_arch(char **cmdline_p) @@ -627,6 +638,8 @@ void __init setup_arch(char **cmdline_p) check_efer(); + discover_ebda(); + init_memory_mapping(0, (end_pfn_map << PAGE_SHIFT)); dmi_scan_machine(); @@ -669,7 +682,8 @@ void __init setup_arch(char **cmdline_p) reserve_bootmem_generic(0, PAGE_SIZE); /* reserve ebda region */ - reserve_ebda_region(); + if (ebda_addr) + reserve_bootmem_generic(ebda_addr, ebda_size); #ifdef CONFIG_SMP /* @@ -1426,3 +1440,22 @@ struct seq_operations cpuinfo_op = { .show = show_cpuinfo, }; +#ifdef CONFIG_INPUT_PCSPKR +#include <linux/platform_device.h> +static __init int add_pcspkr(void) +{ + struct platform_device *pd; + int ret; + + pd = platform_device_alloc("pcspkr", -1); + if (!pd) + return -ENOMEM; + + ret = platform_device_add(pd); + if (ret) + platform_device_put(pd); + + return ret; +} +device_initcall(add_pcspkr); +#endif diff --git a/arch/x86_64/kernel/traps.c b/arch/x86_64/kernel/traps.c index 2700b1375c1..6b87268c5c2 100644 --- a/arch/x86_64/kernel/traps.c +++ b/arch/x86_64/kernel/traps.c @@ -385,6 +385,7 @@ void out_of_line_bug(void) static DEFINE_SPINLOCK(die_lock); static int die_owner = -1; +static unsigned int die_nest_count; unsigned __kprobes long oops_begin(void) { @@ -399,6 +400,7 @@ unsigned __kprobes long oops_begin(void) else spin_lock(&die_lock); } + die_nest_count++; die_owner = cpu; console_verbose(); bust_spinlocks(1); @@ -409,7 +411,13 @@ void __kprobes oops_end(unsigned long flags) { die_owner = -1; bust_spinlocks(0); - spin_unlock_irqrestore(&die_lock, flags); + die_nest_count--; + if (die_nest_count) + /* We still own the lock */ + local_irq_restore(flags); + else + /* Nest count reaches zero, release the lock. */ + spin_unlock_irqrestore(&die_lock, flags); if (panic_on_oops) panic("Oops"); } @@ -464,6 +472,8 @@ void __kprobes die_nmi(char *str, struct pt_regs *regs) panic("nmi watchdog"); printk("console shuts up ...\n"); oops_end(flags); + nmi_exit(); + local_irq_enable(); do_exit(SIGSEGV); } diff --git a/block/elevator.c b/block/elevator.c index 29825792cbd..8768a367fdd 100644 --- a/block/elevator.c +++ b/block/elevator.c @@ -333,6 +333,7 @@ void elv_insert(request_queue_t *q, struct request *rq, int where) { struct list_head *pos; unsigned ordseq; + int unplug_it = 1; blk_add_trace_rq(q, rq, BLK_TA_INSERT); @@ -399,6 +400,11 @@ void elv_insert(request_queue_t *q, struct request *rq, int where) } list_add_tail(&rq->queuelist, pos); + /* + * most requeues happen because of a busy condition, don't + * force unplug of the queue for that case. + */ + unplug_it = 0; break; default: @@ -407,7 +413,7 @@ void elv_insert(request_queue_t *q, struct request *rq, int where) BUG(); } - if (blk_queue_plugged(q)) { + if (unplug_it && blk_queue_plugged(q)) { int nrq = q->rq.count[READ] + q->rq.count[WRITE] - q->in_flight; diff --git a/block/genhd.c b/block/genhd.c index 5a8d3bf02f1..d9657258962 100644 --- a/block/genhd.c +++ b/block/genhd.c @@ -182,6 +182,7 @@ static int exact_lock(dev_t dev, void *data) */ void add_disk(struct gendisk *disk) { + get_device(disk->driverfs_dev); disk->flags |= GENHD_FL_UP; blk_register_region(MKDEV(disk->major, disk->first_minor), disk->minors, NULL, exact_match, exact_lock, disk); @@ -427,6 +428,7 @@ static struct attribute * default_attrs[] = { static void disk_release(struct kobject * kobj) { struct gendisk *disk = to_disk(kobj); + put_device(disk->driverfs_dev); kfree(disk->random); kfree(disk->part); free_disk_stats(disk); diff --git a/block/ll_rw_blk.c b/block/ll_rw_blk.c index e5041a02e21..eac48bec147 100644 --- a/block/ll_rw_blk.c +++ b/block/ll_rw_blk.c @@ -1732,8 +1732,21 @@ void blk_run_queue(struct request_queue *q) spin_lock_irqsave(q->queue_lock, flags); blk_remove_plug(q); - if (!elv_queue_empty(q)) - q->request_fn(q); + + /* + * Only recurse once to avoid overrunning the stack, let the unplug + * handling reinvoke the handler shortly if we already got there. + */ + if (!elv_queue_empty(q)) { + if (!test_and_set_bit(QUEUE_FLAG_REENTER, &q->queue_flags)) { + q->request_fn(q); + clear_bit(QUEUE_FLAG_REENTER, &q->queue_flags); + } else { + blk_plug_device(q); + kblockd_schedule_work(&q->unplug_work); + } + } + spin_unlock_irqrestore(q->queue_lock, flags); } EXPORT_SYMBOL(blk_run_queue); diff --git a/drivers/Kconfig b/drivers/Kconfig index 5c91d6afb11..aeb5ab2391e 100644 --- a/drivers/Kconfig +++ b/drivers/Kconfig @@ -68,8 +68,6 @@ source "drivers/leds/Kconfig" source "drivers/infiniband/Kconfig" -source "drivers/sn/Kconfig" - source "drivers/edac/Kconfig" source "drivers/rtc/Kconfig" diff --git a/drivers/base/class.c b/drivers/base/class.c index 0e71dff327c..b1ea4df85c7 100644 --- a/drivers/base/class.c +++ b/drivers/base/class.c @@ -456,6 +456,35 @@ static void class_device_remove_attrs(struct class_device * cd) } } +static int class_device_add_groups(struct class_device * cd) +{ + int i; + int error = 0; + + if (cd->groups) { + for (i = 0; cd->groups[i]; i++) { + error = sysfs_create_group(&cd->kobj, cd->groups[i]); + if (error) { + while (--i >= 0) + sysfs_remove_group(&cd->kobj, cd->groups[i]); + goto out; + } + } + } +out: + return error; +} + +static void class_device_remove_groups(struct class_device * cd) +{ + int i; + if (cd->groups) { + for (i = 0; cd->groups[i]; i++) { + sysfs_remove_group(&cd->kobj, cd->groups[i]); + } + } +} + static ssize_t show_dev(struct class_device *class_dev, char *buf) { return print_dev_t(buf, class_dev->devt); @@ -559,6 +588,8 @@ int class_device_add(struct class_device *class_dev) class_name); } + class_device_add_groups(class_dev); + kobject_uevent(&class_dev->kobj, KOBJ_ADD); /* notify any interfaces this device is now here */ @@ -672,6 +703,7 @@ void class_device_del(struct class_device *class_dev) if (class_dev->devt_attr) class_device_remove_file(class_dev, class_dev->devt_attr); class_device_remove_attrs(class_dev); + class_device_remove_groups(class_dev); kobject_uevent(&class_dev->kobj, KOBJ_REMOVE); kobject_del(&class_dev->kobj); diff --git a/drivers/block/floppy.c b/drivers/block/floppy.c index bedb689b051..dff1e67b1dd 100644 --- a/drivers/block/floppy.c +++ b/drivers/block/floppy.c @@ -4301,7 +4301,7 @@ static int __init floppy_init(void) } use_virtual_dma = can_use_virtual_dma & 1; -#if defined(CONFIG_PPC64) +#if defined(CONFIG_PPC_MERGE) if (check_legacy_ioport(FDC1)) { del_timer(&fd_timeout); err = -ENODEV; diff --git a/drivers/char/genrtc.c b/drivers/char/genrtc.c index d3a2bc36129..588fca542a9 100644 --- a/drivers/char/genrtc.c +++ b/drivers/char/genrtc.c @@ -200,13 +200,13 @@ static ssize_t gen_rtc_read(struct file *file, char __user *buf, /* first test allows optimizer to nuke this case for 32-bit machines */ if (sizeof (int) != sizeof (long) && count == sizeof (unsigned int)) { unsigned int uidata = data; - retval = put_user(uidata, (unsigned long __user *)buf); + retval = put_user(uidata, (unsigned int __user *)buf) ?: + sizeof(unsigned int); } else { - retval = put_user(data, (unsigned long __user *)buf); + retval = put_user(data, (unsigned long __user *)buf) ?: + sizeof(unsigned long); } - if (!retval) - retval = sizeof(unsigned long); out: current->state = TASK_RUNNING; remove_wait_queue(&gen_rtc_wait, &wait); diff --git a/drivers/char/keyboard.c b/drivers/char/keyboard.c index 935670a3cd9..5755b7e5f18 100644 --- a/drivers/char/keyboard.c +++ b/drivers/char/keyboard.c @@ -860,9 +860,32 @@ static void k_slock(struct vc_data *vc, unsigned char value, char up_flag, struc } /* by default, 300ms interval for combination release */ -static long brl_timeout = 300; -MODULE_PARM_DESC(brl_timeout, "Braille keys release delay in ms (0 for combination on first release, < 0 for dead characters)"); -module_param(brl_timeout, long, 0644); +static unsigned brl_timeout = 300; +MODULE_PARM_DESC(brl_timeout, "Braille keys release delay in ms (0 for commit on first key release)"); +module_param(brl_timeout, uint, 0644); + +static unsigned brl_nbchords = 1; +MODULE_PARM_DESC(brl_nbchords, "Number of chords that produce a braille pattern (0 for dead chords)"); +module_param(brl_nbchords, uint, 0644); + +static void k_brlcommit(struct vc_data *vc, unsigned int pattern, char up_flag, struct pt_regs *regs) +{ + static unsigned long chords; + static unsigned committed; + + if (!brl_nbchords) + k_deadunicode(vc, BRL_UC_ROW | pattern, up_flag, regs); + else { + committed |= pattern; + chords++; + if (chords == brl_nbchords) { + k_unicode(vc, BRL_UC_ROW | committed, up_flag, regs); + chords = 0; + committed = 0; + } + } +} + static void k_brl(struct vc_data *vc, unsigned char value, char up_flag, struct pt_regs *regs) { static unsigned pressed,committing; @@ -882,11 +905,6 @@ static void k_brl(struct vc_data *vc, unsigned char value, char up_flag, struct if (value > 8) return; - if (brl_timeout < 0) { - k_deadunicode(vc, BRL_UC_ROW | (1 << (value - 1)), up_flag, regs); - return; - } - if (up_flag) { if (brl_timeout) { if (!committing || @@ -897,13 +915,13 @@ static void k_brl(struct vc_data *vc, unsigned char value, char up_flag, struct pressed &= ~(1 << (value - 1)); if (!pressed) { if (committing) { - k_unicode(vc, BRL_UC_ROW | committing, 0, regs); + k_brlcommit(vc, committing, 0, regs); committing = 0; } } } else { if (committing) { - k_unicode(vc, BRL_UC_ROW | committing, 0, regs); + k_brlcommit(vc, committing, 0, regs); committing = 0; } pressed &= ~(1 << (value - 1)); diff --git a/drivers/char/mwave/mwavedd.c b/drivers/char/mwave/mwavedd.c index 8666171e187..d3ba2f860ef 100644 --- a/drivers/char/mwave/mwavedd.c +++ b/drivers/char/mwave/mwavedd.c @@ -271,7 +271,7 @@ static int mwave_ioctl(struct inode *inode, struct file *file, ipcnum, pDrvData->IPCs[ipcnum].usIntCount); - if (ipcnum > ARRAY_SIZE(pDrvData->IPCs)) { + if (ipcnum >= ARRAY_SIZE(pDrvData->IPCs)) { PRINTK_ERROR(KERN_ERR_MWAVE "mwavedd::mwave_ioctl:" " IOCTL_MW_REGISTER_IPC:" diff --git a/drivers/char/pcmcia/cm4000_cs.c b/drivers/char/pcmcia/cm4000_cs.c index 02114a0bd0d..128b2632512 100644 --- a/drivers/char/pcmcia/cm4000_cs.c +++ b/drivers/char/pcmcia/cm4000_cs.c @@ -1981,10 +1981,6 @@ static int __init cmm_init(void) if (!cmm_class) return -1; - rc = pcmcia_register_driver(&cm4000_driver); - if (rc < 0) - return rc; - major = register_chrdev(0, DEVICE_NAME, &cm4000_fops); if (major < 0) { printk(KERN_WARNING MODULE_NAME @@ -1992,6 +1988,12 @@ static int __init cmm_init(void) return -1; } + rc = pcmcia_register_driver(&cm4000_driver); + if (rc < 0) { + unregister_chrdev(major, DEVICE_NAME); + return rc; + } + return 0; } diff --git a/drivers/char/pcmcia/cm4040_cs.c b/drivers/char/pcmcia/cm4040_cs.c index 29efa64580a..47a8465bf95 100644 --- a/drivers/char/pcmcia/cm4040_cs.c +++ b/drivers/char/pcmcia/cm4040_cs.c @@ -724,16 +724,19 @@ static int __init cm4040_init(void) if (!cmx_class) return -1; - rc = pcmcia_register_driver(&reader_driver); - if (rc < 0) - return rc; - major = register_chrdev(0, DEVICE_NAME, &reader_fops); if (major < 0) { printk(KERN_WARNING MODULE_NAME ": could not get major number\n"); return -1; } + + rc = pcmcia_register_driver(&reader_driver); + if (rc < 0) { + unregister_chrdev(major, DEVICE_NAME); + return rc; + } + return 0; } diff --git a/drivers/char/tipar.c b/drivers/char/tipar.c index eb2eb3e12d6..079db5a935a 100644 --- a/drivers/char/tipar.c +++ b/drivers/char/tipar.c @@ -515,7 +515,7 @@ tipar_init_module(void) err = PTR_ERR(tipar_class); goto out_chrdev; } - if (parport_register_driver(&tipar_driver) || tp_count == 0) { + if (parport_register_driver(&tipar_driver)) { printk(KERN_ERR "tipar: unable to register with parport\n"); err = -EIO; goto out_class; diff --git a/drivers/cpufreq/cpufreq_ondemand.c b/drivers/cpufreq/cpufreq_ondemand.c index 956d121cb16..3e6ffcaa5af 100644 --- a/drivers/cpufreq/cpufreq_ondemand.c +++ b/drivers/cpufreq/cpufreq_ondemand.c @@ -74,6 +74,8 @@ static unsigned int dbs_enable; /* number of CPUs using this policy */ static DEFINE_MUTEX (dbs_mutex); static DECLARE_WORK (dbs_work, do_dbs_timer, NULL); +static struct workqueue_struct *dbs_workq; + struct dbs_tuners { unsigned int sampling_rate; unsigned int sampling_down_factor; @@ -364,23 +366,29 @@ static void do_dbs_timer(void *data) mutex_lock(&dbs_mutex); for_each_online_cpu(i) dbs_check_cpu(i); - schedule_delayed_work(&dbs_work, - usecs_to_jiffies(dbs_tuners_ins.sampling_rate)); + queue_delayed_work(dbs_workq, &dbs_work, + usecs_to_jiffies(dbs_tuners_ins.sampling_rate)); mutex_unlock(&dbs_mutex); } static inline void dbs_timer_init(void) { INIT_WORK(&dbs_work, do_dbs_timer, NULL); - schedule_delayed_work(&dbs_work, - usecs_to_jiffies(dbs_tuners_ins.sampling_rate)); + if (!dbs_workq) + dbs_workq = create_singlethread_workqueue("ondemand"); + if (!dbs_workq) { + printk(KERN_ERR "ondemand: Cannot initialize kernel thread\n"); + return; + } + queue_delayed_work(dbs_workq, &dbs_work, + usecs_to_jiffies(dbs_tuners_ins.sampling_rate)); return; } static inline void dbs_timer_exit(void) { - cancel_delayed_work(&dbs_work); - return; + if (dbs_workq) + cancel_rearming_delayed_workqueue(dbs_workq, &dbs_work); } static int cpufreq_governor_dbs(struct cpufreq_policy *policy, @@ -489,8 +497,12 @@ static int __init cpufreq_gov_dbs_init(void) static void __exit cpufreq_gov_dbs_exit(void) { - /* Make sure that the scheduled work is indeed not running */ - flush_scheduled_work(); + /* Make sure that the scheduled work is indeed not running. + Assumes the timer has been cancelled first. */ + if (dbs_workq) { + flush_workqueue(dbs_workq); + destroy_workqueue(dbs_workq); + } cpufreq_unregister_governor(&cpufreq_gov_dbs); } diff --git a/drivers/edac/e752x_edac.c b/drivers/edac/e752x_edac.c index 66572c5323a..fce31936e6d 100644 --- a/drivers/edac/e752x_edac.c +++ b/drivers/edac/e752x_edac.c @@ -25,6 +25,8 @@ #include <linux/slab.h> #include "edac_mc.h" +static int force_function_unhide; + #define e752x_printk(level, fmt, arg...) \ edac_printk(level, "e752x", fmt, ##arg) @@ -782,8 +784,16 @@ static int e752x_probe1(struct pci_dev *pdev, int dev_idx) debugf0("%s(): mci\n", __func__); debugf0("Starting Probe1\n"); - /* enable device 0 function 1 */ + /* check to see if device 0 function 1 is enabled; if it isn't, we + * assume the BIOS has reserved it for a reason and is expecting + * exclusive access, we take care not to violate that assumption and + * fail the probe. */ pci_read_config_byte(pdev, E752X_DEVPRES1, &stat8); + if (!force_function_unhide && !(stat8 & (1 << 5))) { + printk(KERN_INFO "Contact your BIOS vendor to see if the " + "E752x error registers can be safely un-hidden\n"); + goto fail; + } stat8 |= (1 << 5); pci_write_config_byte(pdev, E752X_DEVPRES1, stat8); @@ -1063,3 +1073,8 @@ module_exit(e752x_exit); MODULE_LICENSE("GPL"); MODULE_AUTHOR("Linux Networx (http://lnxi.com) Tom Zimmerman\n"); MODULE_DESCRIPTION("MC support for Intel e752x memory controllers"); + +module_param(force_function_unhide, int, 0444); +MODULE_PARM_DESC(force_function_unhide, "if BIOS sets Dev0:Fun1 up as hidden:" +" 1=force unhide and hope BIOS doesn't fight driver for Dev0:Fun1 access"); + diff --git a/drivers/infiniband/core/sysfs.c b/drivers/infiniband/core/sysfs.c index 15121cb5a1f..21f9282c1b2 100644 --- a/drivers/infiniband/core/sysfs.c +++ b/drivers/infiniband/core/sysfs.c @@ -336,7 +336,7 @@ static ssize_t show_pma_counter(struct ib_port *p, struct port_attribute *attr, switch (width) { case 4: ret = sprintf(buf, "%u\n", (out_mad->data[40 + offset / 8] >> - (offset % 4)) & 0xf); + (4 - (offset % 8))) & 0xf); break; case 8: ret = sprintf(buf, "%u\n", out_mad->data[40 + offset / 8]); diff --git a/drivers/infiniband/hw/ipath/ipath_debug.h b/drivers/infiniband/hw/ipath/ipath_debug.h index 593e28969c6..46762387f5f 100644 --- a/drivers/infiniband/hw/ipath/ipath_debug.h +++ b/drivers/infiniband/hw/ipath/ipath_debug.h @@ -60,11 +60,11 @@ #define __IPATH_KERNEL_SEND 0x2000 /* use kernel mode send */ #define __IPATH_EPKTDBG 0x4000 /* print ethernet packet data */ #define __IPATH_SMADBG 0x8000 /* sma packet debug */ -#define __IPATH_IPATHDBG 0x10000 /* Ethernet (IPATH) general debug on */ -#define __IPATH_IPATHWARN 0x20000 /* Ethernet (IPATH) warnings on */ -#define __IPATH_IPATHERR 0x40000 /* Ethernet (IPATH) errors on */ -#define __IPATH_IPATHPD 0x80000 /* Ethernet (IPATH) packet dump on */ -#define __IPATH_IPATHTABLE 0x100000 /* Ethernet (IPATH) table dump on */ +#define __IPATH_IPATHDBG 0x10000 /* Ethernet (IPATH) gen debug */ +#define __IPATH_IPATHWARN 0x20000 /* Ethernet (IPATH) warnings */ +#define __IPATH_IPATHERR 0x40000 /* Ethernet (IPATH) errors */ +#define __IPATH_IPATHPD 0x80000 /* Ethernet (IPATH) packet dump */ +#define __IPATH_IPATHTABLE 0x100000 /* Ethernet (IPATH) table dump */ #else /* _IPATH_DEBUGGING */ @@ -79,11 +79,12 @@ #define __IPATH_TRSAMPLE 0x0 /* generate trace buffer sample entries */ #define __IPATH_VERBDBG 0x0 /* very verbose debug */ #define __IPATH_PKTDBG 0x0 /* print packet data */ -#define __IPATH_PROCDBG 0x0 /* print process startup (init)/exit messages */ +#define __IPATH_PROCDBG 0x0 /* process startup (init)/exit messages */ /* print mmap/nopage stuff, not using VDBG any more */ #define __IPATH_MMDBG 0x0 #define __IPATH_EPKTDBG 0x0 /* print ethernet packet data */ -#define __IPATH_SMADBG 0x0 /* print process startup (init)/exit messages */#define __IPATH_IPATHDBG 0x0 /* Ethernet (IPATH) table dump on */ +#define __IPATH_SMADBG 0x0 /* process startup (init)/exit messages */ +#define __IPATH_IPATHDBG 0x0 /* Ethernet (IPATH) table dump on */ #define __IPATH_IPATHWARN 0x0 /* Ethernet (IPATH) warnings on */ #define __IPATH_IPATHERR 0x0 /* Ethernet (IPATH) errors on */ #define __IPATH_IPATHPD 0x0 /* Ethernet (IPATH) packet dump on */ diff --git a/drivers/infiniband/hw/ipath/ipath_diag.c b/drivers/infiniband/hw/ipath/ipath_diag.c index 7d3fb6996b4..28ddceb260e 100644 --- a/drivers/infiniband/hw/ipath/ipath_diag.c +++ b/drivers/infiniband/hw/ipath/ipath_diag.c @@ -277,13 +277,14 @@ static int ipath_diag_open(struct inode *in, struct file *fp) bail: spin_unlock_irqrestore(&ipath_devs_lock, flags); - mutex_unlock(&ipath_mutex); /* Only expose a way to reset the device if we make it into diag mode. */ if (ret == 0) ipath_expose_reset(&dd->pcidev->dev); + mutex_unlock(&ipath_mutex); + return ret; } diff --git a/drivers/infiniband/hw/ipath/ipath_driver.c b/drivers/infiniband/hw/ipath/ipath_driver.c index e7617c3982e..398add4d4cb 100644 --- a/drivers/infiniband/hw/ipath/ipath_driver.c +++ b/drivers/infiniband/hw/ipath/ipath_driver.c @@ -418,9 +418,19 @@ static int __devinit ipath_init_one(struct pci_dev *pdev, ret = pci_set_dma_mask(pdev, DMA_64BIT_MASK); if (ret) { - dev_info(&pdev->dev, "pci_set_dma_mask unit %u " - "fails: %d\n", dd->ipath_unit, ret); - goto bail_regions; + /* + * if the 64 bit setup fails, try 32 bit. Some systems + * do not setup 64 bit maps on systems with 2GB or less + * memory installed. + */ + ret = pci_set_dma_mask(pdev, DMA_32BIT_MASK); + if (ret) { + dev_info(&pdev->dev, "pci_set_dma_mask unit %u " + "fails: %d\n", dd->ipath_unit, ret); + goto bail_regions; + } + else + ipath_dbg("No 64bit DMA mask, used 32 bit mask\n"); } pci_set_master(pdev); @@ -1949,7 +1959,7 @@ int ipath_reset_device(int unit) } if (dd->ipath_pd) - for (i = 1; i < dd->ipath_portcnt; i++) { + for (i = 1; i < dd->ipath_cfgports; i++) { if (dd->ipath_pd[i] && dd->ipath_pd[i]->port_cnt) { ipath_dbg("unit %u port %d is in use " "(PID %u cmd %s), can't reset\n", diff --git a/drivers/infiniband/hw/ipath/ipath_init_chip.c b/drivers/infiniband/hw/ipath/ipath_init_chip.c index 2823ff9c0c6..16f640e1c16 100644 --- a/drivers/infiniband/hw/ipath/ipath_init_chip.c +++ b/drivers/infiniband/hw/ipath/ipath_init_chip.c @@ -53,13 +53,19 @@ MODULE_PARM_DESC(cfgports, "Set max number of ports to use"); /* * Number of buffers reserved for driver (layered drivers and SMA - * send). Reserved at end of buffer list. + * send). Reserved at end of buffer list. Initialized based on + * number of PIO buffers if not set via module interface. + * The problem with this is that it's global, but we'll use different + * numbers for different chip types. So the default value is not + * very useful. I've redefined it for the 1.3 release so that it's + * zero unless set by the user to something else, in which case we + * try to respect it. */ -static ushort ipath_kpiobufs = 32; +static ushort ipath_kpiobufs; static int ipath_set_kpiobufs(const char *val, struct kernel_param *kp); -module_param_call(kpiobufs, ipath_set_kpiobufs, param_get_uint, +module_param_call(kpiobufs, ipath_set_kpiobufs, param_get_ushort, &ipath_kpiobufs, S_IWUSR | S_IRUGO); MODULE_PARM_DESC(kpiobufs, "Set number of PIO buffers for driver"); @@ -531,8 +537,11 @@ static int init_housekeeping(struct ipath_devdata *dd, * Don't clear ipath_flags as 8bit mode was set before * entering this func. However, we do set the linkstate to * unknown, so we can watch for a transition. + * PRESENT is set because we want register reads to work, + * and the kernel infrastructure saw it in config space; + * We clear it if we have failures. */ - dd->ipath_flags |= IPATH_LINKUNK; + dd->ipath_flags |= IPATH_LINKUNK | IPATH_PRESENT; dd->ipath_flags &= ~(IPATH_LINKACTIVE | IPATH_LINKARMED | IPATH_LINKDOWN | IPATH_LINKINIT); @@ -560,6 +569,7 @@ static int init_housekeeping(struct ipath_devdata *dd, || (dd->ipath_uregbase & 0xffffffff) == 0xffffffff) { ipath_dev_err(dd, "Register read failures from chip, " "giving up initialization\n"); + dd->ipath_flags &= ~IPATH_PRESENT; ret = -ENODEV; goto done; } @@ -682,16 +692,14 @@ int ipath_init_chip(struct ipath_devdata *dd, int reinit) */ dd->ipath_pioavregs = ALIGN(val, sizeof(u64) * BITS_PER_BYTE / 2) / (sizeof(u64) * BITS_PER_BYTE / 2); - if (!ipath_kpiobufs) /* have to have at least 1, for SMA */ - kpiobufs = ipath_kpiobufs = 1; - else if ((dd->ipath_piobcnt2k + dd->ipath_piobcnt4k) < - (dd->ipath_cfgports * IPATH_MIN_USER_PORT_BUFCNT)) { - dev_info(&dd->pcidev->dev, "Too few PIO buffers (%u) " - "for %u ports to have %u each!\n", - dd->ipath_piobcnt2k + dd->ipath_piobcnt4k, - dd->ipath_cfgports, IPATH_MIN_USER_PORT_BUFCNT); - kpiobufs = 1; /* reserve just the minimum for SMA/ether */ - } else + if (ipath_kpiobufs == 0) { + /* not set by user, or set explictly to default */ + if ((dd->ipath_piobcnt2k + dd->ipath_piobcnt4k) > 128) + kpiobufs = 32; + else + kpiobufs = 16; + } + else kpiobufs = ipath_kpiobufs; if (kpiobufs > diff --git a/drivers/infiniband/hw/ipath/ipath_intr.c b/drivers/infiniband/hw/ipath/ipath_intr.c index 0bcb428041f..3e72a1fe3d7 100644 --- a/drivers/infiniband/hw/ipath/ipath_intr.c +++ b/drivers/infiniband/hw/ipath/ipath_intr.c @@ -665,14 +665,14 @@ static void handle_layer_pioavail(struct ipath_devdata *dd) ret = __ipath_layer_intr(dd, IPATH_LAYER_INT_SEND_CONTINUE); if (ret > 0) - goto clear; + goto set; ret = __ipath_verbs_piobufavail(dd); if (ret > 0) - goto clear; + goto set; return; -clear: +set: set_bit(IPATH_S_PIOINTBUFAVAIL, &dd->ipath_sendctrl); ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl, dd->ipath_sendctrl); @@ -719,11 +719,24 @@ static void handle_rcv(struct ipath_devdata *dd, u32 istat) irqreturn_t ipath_intr(int irq, void *data, struct pt_regs *regs) { struct ipath_devdata *dd = data; - u32 istat = ipath_read_kreg32(dd, dd->ipath_kregs->kr_intstatus); + u32 istat; ipath_err_t estat = 0; static unsigned unexpected = 0; irqreturn_t ret; + if(!(dd->ipath_flags & IPATH_PRESENT)) { + /* this is mostly so we don't try to touch the chip while + * it is being reset */ + /* + * This return value is perhaps odd, but we do not want the + * interrupt core code to remove our interrupt handler + * because we don't appear to be handling an interrupt + * during a chip reset. + */ + return IRQ_HANDLED; + } + + istat = ipath_read_kreg32(dd, dd->ipath_kregs->kr_intstatus); if (unlikely(!istat)) { ipath_stats.sps_nullintr++; ret = IRQ_NONE; /* not our interrupt, or already handled */ diff --git a/drivers/infiniband/hw/ipath/ipath_kernel.h b/drivers/infiniband/hw/ipath/ipath_kernel.h index 0ce5f19c9d6..e6507f8115b 100644 --- a/drivers/infiniband/hw/ipath/ipath_kernel.h +++ b/drivers/infiniband/hw/ipath/ipath_kernel.h @@ -731,7 +731,7 @@ u64 ipath_read_kreg64_port(const struct ipath_devdata *, ipath_kreg, static inline u32 ipath_read_ureg32(const struct ipath_devdata *dd, ipath_ureg regno, int port) { - if (!dd->ipath_kregbase) + if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT)) return 0; return readl(regno + (u64 __iomem *) @@ -762,7 +762,7 @@ static inline void ipath_write_ureg(const struct ipath_devdata *dd, static inline u32 ipath_read_kreg32(const struct ipath_devdata *dd, ipath_kreg regno) { - if (!dd->ipath_kregbase) + if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT)) return -1; return readl((u32 __iomem *) & dd->ipath_kregbase[regno]); } @@ -770,7 +770,7 @@ static inline u32 ipath_read_kreg32(const struct ipath_devdata *dd, static inline u64 ipath_read_kreg64(const struct ipath_devdata *dd, ipath_kreg regno) { - if (!dd->ipath_kregbase) + if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT)) return -1; return readq(&dd->ipath_kregbase[regno]); @@ -786,7 +786,7 @@ static inline void ipath_write_kreg(const struct ipath_devdata *dd, static inline u64 ipath_read_creg(const struct ipath_devdata *dd, ipath_sreg regno) { - if (!dd->ipath_kregbase) + if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT)) return 0; return readq(regno + (u64 __iomem *) @@ -797,7 +797,7 @@ static inline u64 ipath_read_creg(const struct ipath_devdata *dd, static inline u32 ipath_read_creg32(const struct ipath_devdata *dd, ipath_sreg regno) { - if (!dd->ipath_kregbase) + if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT)) return 0; return readl(regno + (u64 __iomem *) (dd->ipath_cregbase + diff --git a/drivers/infiniband/hw/ipath/ipath_layer.c b/drivers/infiniband/hw/ipath/ipath_layer.c index 69ed1100701..9cb5258ffed 100644 --- a/drivers/infiniband/hw/ipath/ipath_layer.c +++ b/drivers/infiniband/hw/ipath/ipath_layer.c @@ -46,13 +46,15 @@ /* Acquire before ipath_devs_lock. */ static DEFINE_MUTEX(ipath_layer_mutex); +static int ipath_verbs_registered; + u16 ipath_layer_rcv_opcode; + static int (*layer_intr)(void *, u32); static int (*layer_rcv)(void *, void *, struct sk_buff *); static int (*layer_rcv_lid)(void *, void *); static int (*verbs_piobufavail)(void *); static void (*verbs_rcv)(void *, void *, void *, u32); -static int ipath_verbs_registered; static void *(*layer_add_one)(int, struct ipath_devdata *); static void (*layer_remove_one)(void *); @@ -586,6 +588,8 @@ void ipath_verbs_unregister(void) verbs_rcv = NULL; verbs_timer_cb = NULL; + ipath_verbs_registered = 0; + mutex_unlock(&ipath_layer_mutex); } diff --git a/drivers/infiniband/hw/ipath/ipath_pe800.c b/drivers/infiniband/hw/ipath/ipath_pe800.c index e1dc4f75706..6318067ab5e 100644 --- a/drivers/infiniband/hw/ipath/ipath_pe800.c +++ b/drivers/infiniband/hw/ipath/ipath_pe800.c @@ -972,6 +972,8 @@ static int ipath_setup_pe_reset(struct ipath_devdata *dd) /* Use ERROR so it shows up in logs, etc. */ ipath_dev_err(dd, "Resetting PE-800 unit %u\n", dd->ipath_unit); + /* keep chip from being accessed in a few places */ + dd->ipath_flags &= ~(IPATH_INITTED|IPATH_PRESENT); val = dd->ipath_control | INFINIPATH_C_RESET; ipath_write_kreg(dd, dd->ipath_kregs->kr_control, val); mb(); @@ -997,6 +999,8 @@ static int ipath_setup_pe_reset(struct ipath_devdata *dd) if ((r = pci_enable_device(dd->pcidev))) ipath_dev_err(dd, "pci_enable_device failed after " "reset: %d\n", r); + /* whether it worked or not, mark as present, again */ + dd->ipath_flags |= IPATH_PRESENT; val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_revision); if (val == dd->ipath_revision) { ipath_cdbg(VERBOSE, "Got matching revision " diff --git a/drivers/infiniband/hw/ipath/ipath_registers.h b/drivers/infiniband/hw/ipath/ipath_registers.h index 1e59750c5f6..402126eb79c 100644 --- a/drivers/infiniband/hw/ipath/ipath_registers.h +++ b/drivers/infiniband/hw/ipath/ipath_registers.h @@ -34,8 +34,9 @@ #define _IPATH_REGISTERS_H /* - * This file should only be included by kernel source, and by the diags. - * It defines the registers, and their contents, for the InfiniPath HT-400 chip + * This file should only be included by kernel source, and by the diags. It + * defines the registers, and their contents, for the InfiniPath HT-400 + * chip. */ /* @@ -156,8 +157,10 @@ #define INFINIPATH_IBCC_FLOWCTRLWATERMARK_SHIFT 8 #define INFINIPATH_IBCC_LINKINITCMD_MASK 0x3ULL #define INFINIPATH_IBCC_LINKINITCMD_DISABLE 1 -#define INFINIPATH_IBCC_LINKINITCMD_POLL 2 /* cycle through TS1/TS2 till OK */ -#define INFINIPATH_IBCC_LINKINITCMD_SLEEP 3 /* wait for TS1, then go on */ +/* cycle through TS1/TS2 till OK */ +#define INFINIPATH_IBCC_LINKINITCMD_POLL 2 +/* wait for TS1, then go on */ +#define INFINIPATH_IBCC_LINKINITCMD_SLEEP 3 #define INFINIPATH_IBCC_LINKINITCMD_SHIFT 16 #define INFINIPATH_IBCC_LINKCMD_MASK 0x3ULL #define INFINIPATH_IBCC_LINKCMD_INIT 1 /* move to 0x11 */ @@ -182,7 +185,8 @@ #define INFINIPATH_IBCS_LINKSTATE_SHIFT 4 #define INFINIPATH_IBCS_TXREADY 0x40000000 #define INFINIPATH_IBCS_TXCREDITOK 0x80000000 -/* link training states (shift by INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) */ +/* link training states (shift by + INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) */ #define INFINIPATH_IBCS_LT_STATE_DISABLED 0x00 #define INFINIPATH_IBCS_LT_STATE_LINKUP 0x01 #define INFINIPATH_IBCS_LT_STATE_POLLACTIVE 0x02 @@ -267,10 +271,12 @@ /* kr_serdesconfig0 bits */ #define INFINIPATH_SERDC0_RESET_MASK 0xfULL /* overal reset bits */ #define INFINIPATH_SERDC0_RESET_PLL 0x10000000ULL /* pll reset */ -#define INFINIPATH_SERDC0_TXIDLE 0xF000ULL /* tx idle enables (per lane) */ -#define INFINIPATH_SERDC0_RXDETECT_EN 0xF0000ULL /* rx detect enables (per lane) */ -#define INFINIPATH_SERDC0_L1PWR_DN 0xF0ULL /* L1 Power down; use with RXDETECT, - Otherwise not used on IB side */ +/* tx idle enables (per lane) */ +#define INFINIPATH_SERDC0_TXIDLE 0xF000ULL +/* rx detect enables (per lane) */ +#define INFINIPATH_SERDC0_RXDETECT_EN 0xF0000ULL +/* L1 Power down; use with RXDETECT, Otherwise not used on IB side */ +#define INFINIPATH_SERDC0_L1PWR_DN 0xF0ULL /* kr_xgxsconfig bits */ #define INFINIPATH_XGXS_RESET 0x7ULL @@ -390,12 +396,13 @@ struct ipath_kregs { ipath_kreg kr_txintmemsize; ipath_kreg kr_xgxsconfig; ipath_kreg kr_ibpllcfg; - /* use these two (and the following N ports) only with ipath_k*_kreg64_port(); - * not *kreg64() */ + /* use these two (and the following N ports) only with + * ipath_k*_kreg64_port(); not *kreg64() */ ipath_kreg kr_rcvhdraddr; ipath_kreg kr_rcvhdrtailaddr; - /* remaining registers are not present on all types of infinipath chips */ + /* remaining registers are not present on all types of infinipath + chips */ ipath_kreg kr_rcvpktledcnt; ipath_kreg kr_pcierbuftestreg0; ipath_kreg kr_pcierbuftestreg1; diff --git a/drivers/infiniband/hw/ipath/ipath_ruc.c b/drivers/infiniband/hw/ipath/ipath_ruc.c index f232e77b78e..eb81424b3c5 100644 --- a/drivers/infiniband/hw/ipath/ipath_ruc.c +++ b/drivers/infiniband/hw/ipath/ipath_ruc.c @@ -531,19 +531,12 @@ int ipath_post_rc_send(struct ipath_qp *qp, struct ib_send_wr *wr) } wqe->wr.num_sge = j; qp->s_head = next; - /* - * Wake up the send tasklet if the QP is not waiting - * for an RNR timeout. - */ - next = qp->s_rnr_timeout; spin_unlock_irqrestore(&qp->s_lock, flags); - if (next == 0) { - if (qp->ibqp.qp_type == IB_QPT_UC) - ipath_do_uc_send((unsigned long) qp); - else - ipath_do_rc_send((unsigned long) qp); - } + if (qp->ibqp.qp_type == IB_QPT_UC) + ipath_do_uc_send((unsigned long) qp); + else + ipath_do_rc_send((unsigned long) qp); ret = 0; diff --git a/drivers/infiniband/hw/ipath/ipath_sysfs.c b/drivers/infiniband/hw/ipath/ipath_sysfs.c index 32acd8048b4..f323791cc49 100644 --- a/drivers/infiniband/hw/ipath/ipath_sysfs.c +++ b/drivers/infiniband/hw/ipath/ipath_sysfs.c @@ -711,10 +711,22 @@ static struct attribute_group dev_attr_group = { * enters diag mode. A device reset is quite likely to crash the * machine entirely, so we don't want to normally make it * available. + * + * Called with ipath_mutex held. */ int ipath_expose_reset(struct device *dev) { - return device_create_file(dev, &dev_attr_reset); + static int exposed; + int ret; + + if (!exposed) { + ret = device_create_file(dev, &dev_attr_reset); + exposed = 1; + } + else + ret = 0; + + return ret; } int ipath_driver_create_group(struct device_driver *drv) diff --git a/drivers/infiniband/hw/ipath/ipath_ud.c b/drivers/infiniband/hw/ipath/ipath_ud.c index 01cfb30ee16..e606daf8321 100644 --- a/drivers/infiniband/hw/ipath/ipath_ud.c +++ b/drivers/infiniband/hw/ipath/ipath_ud.c @@ -46,8 +46,10 @@ * This is called from ipath_post_ud_send() to forward a WQE addressed * to the same HCA. */ -static void ipath_ud_loopback(struct ipath_qp *sqp, struct ipath_sge_state *ss, - u32 length, struct ib_send_wr *wr, struct ib_wc *wc) +static void ipath_ud_loopback(struct ipath_qp *sqp, + struct ipath_sge_state *ss, + u32 length, struct ib_send_wr *wr, + struct ib_wc *wc) { struct ipath_ibdev *dev = to_idev(sqp->ibqp.device); struct ipath_qp *qp; diff --git a/drivers/infiniband/hw/ipath/ipath_verbs.c b/drivers/infiniband/hw/ipath/ipath_verbs.c index 8d2558a01f3..cb9e387c301 100644 --- a/drivers/infiniband/hw/ipath/ipath_verbs.c +++ b/drivers/infiniband/hw/ipath/ipath_verbs.c @@ -449,7 +449,6 @@ static void ipath_ib_timer(void *arg) { struct ipath_ibdev *dev = (struct ipath_ibdev *) arg; struct ipath_qp *resend = NULL; - struct ipath_qp *rnr = NULL; struct list_head *last; struct ipath_qp *qp; unsigned long flags; @@ -465,32 +464,18 @@ static void ipath_ib_timer(void *arg) last = &dev->pending[dev->pending_index]; while (!list_empty(last)) { qp = list_entry(last->next, struct ipath_qp, timerwait); - if (last->next == LIST_POISON1 || - last->next != &qp->timerwait || - qp->timerwait.prev != last) { - INIT_LIST_HEAD(last); - } else { - list_del(&qp->timerwait); - qp->timerwait.prev = (struct list_head *) resend; - resend = qp; - atomic_inc(&qp->refcount); - } + list_del(&qp->timerwait); + qp->timer_next = resend; + resend = qp; + atomic_inc(&qp->refcount); } last = &dev->rnrwait; if (!list_empty(last)) { qp = list_entry(last->next, struct ipath_qp, timerwait); if (--qp->s_rnr_timeout == 0) { do { - if (last->next == LIST_POISON1 || - last->next != &qp->timerwait || - qp->timerwait.prev != last) { - INIT_LIST_HEAD(last); - break; - } list_del(&qp->timerwait); - qp->timerwait.prev = - (struct list_head *) rnr; - rnr = qp; + tasklet_hi_schedule(&qp->s_task); if (list_empty(last)) break; qp = list_entry(last->next, struct ipath_qp, @@ -530,8 +515,7 @@ static void ipath_ib_timer(void *arg) spin_unlock_irqrestore(&dev->pending_lock, flags); /* XXX What if timer fires again while this is running? */ - for (qp = resend; qp != NULL; - qp = (struct ipath_qp *) qp->timerwait.prev) { + for (qp = resend; qp != NULL; qp = qp->timer_next) { struct ib_wc wc; spin_lock_irqsave(&qp->s_lock, flags); @@ -545,9 +529,6 @@ static void ipath_ib_timer(void *arg) if (atomic_dec_and_test(&qp->refcount)) wake_up(&qp->wait); } - for (qp = rnr; qp != NULL; - qp = (struct ipath_qp *) qp->timerwait.prev) - tasklet_hi_schedule(&qp->s_task); } /** @@ -556,9 +537,9 @@ static void ipath_ib_timer(void *arg) * * This is called from ipath_intr() at interrupt level when a PIO buffer is * available after ipath_verbs_send() returned an error that no buffers were - * available. Return 0 if we consumed all the PIO buffers and we still have + * available. Return 1 if we consumed all the PIO buffers and we still have * QPs waiting for buffers (for now, just do a tasklet_hi_schedule and - * return one). + * return zero). */ static int ipath_ib_piobufavail(void *arg) { @@ -579,7 +560,7 @@ static int ipath_ib_piobufavail(void *arg) spin_unlock_irqrestore(&dev->pending_lock, flags); bail: - return 1; + return 0; } static int ipath_query_device(struct ib_device *ibdev, @@ -1159,7 +1140,7 @@ static ssize_t show_stats(struct class_device *cdev, char *buf) len = sprintf(buf, "RC resends %d\n" - "RC QACKs %d\n" + "RC no QACK %d\n" "RC ACKs %d\n" "RC SEQ NAKs %d\n" "RC RDMA seq %d\n" diff --git a/drivers/infiniband/hw/ipath/ipath_verbs.h b/drivers/infiniband/hw/ipath/ipath_verbs.h index fcafbc7c9e7..4f8d59300e9 100644 --- a/drivers/infiniband/hw/ipath/ipath_verbs.h +++ b/drivers/infiniband/hw/ipath/ipath_verbs.h @@ -282,7 +282,8 @@ struct ipath_srq { */ struct ipath_qp { struct ib_qp ibqp; - struct ipath_qp *next; /* link list for QPN hash table */ + struct ipath_qp *next; /* link list for QPN hash table */ + struct ipath_qp *timer_next; /* link list for ipath_ib_timer() */ struct list_head piowait; /* link for wait PIO buf */ struct list_head timerwait; /* link for waiting for timeouts */ struct ib_ah_attr remote_ah_attr; diff --git a/drivers/infiniband/hw/ipath/ips_common.h b/drivers/infiniband/hw/ipath/ips_common.h index 410a764dfce..ab7cbbbfd03 100644 --- a/drivers/infiniband/hw/ipath/ips_common.h +++ b/drivers/infiniband/hw/ipath/ips_common.h @@ -95,7 +95,7 @@ struct ether_header { __u8 seq_num; __le32 len; /* MUST be of word size due to PIO write requirements */ - __u32 csum; + __le32 csum; __le16 csum_offset; __le16 flags; __u16 first_2_bytes; diff --git a/drivers/infiniband/hw/mthca/mthca_cq.c b/drivers/infiniband/hw/mthca/mthca_cq.c index 312cf90731e..205854e9c66 100644 --- a/drivers/infiniband/hw/mthca/mthca_cq.c +++ b/drivers/infiniband/hw/mthca/mthca_cq.c @@ -238,9 +238,9 @@ void mthca_cq_event(struct mthca_dev *dev, u32 cqn, spin_lock(&dev->cq_table.lock); cq = mthca_array_get(&dev->cq_table.cq, cqn & (dev->limits.num_cqs - 1)); - if (cq) - atomic_inc(&cq->refcount); + ++cq->refcount; + spin_unlock(&dev->cq_table.lock); if (!cq) { @@ -254,8 +254,10 @@ void mthca_cq_event(struct mthca_dev *dev, u32 cqn, if (cq->ibcq.event_handler) cq->ibcq.event_handler(&event, cq->ibcq.cq_context); - if (atomic_dec_and_test(&cq->refcount)) + spin_lock(&dev->cq_table.lock); + if (!--cq->refcount) wake_up(&cq->wait); + spin_unlock(&dev->cq_table.lock); } static inline int is_recv_cqe(struct mthca_cqe *cqe) @@ -267,23 +269,13 @@ static inline int is_recv_cqe(struct mthca_cqe *cqe) return !(cqe->is_send & 0x80); } -void mthca_cq_clean(struct mthca_dev *dev, u32 cqn, u32 qpn, +void mthca_cq_clean(struct mthca_dev *dev, struct mthca_cq *cq, u32 qpn, struct mthca_srq *srq) { - struct mthca_cq *cq; struct mthca_cqe *cqe; u32 prod_index; int nfreed = 0; - spin_lock_irq(&dev->cq_table.lock); - cq = mthca_array_get(&dev->cq_table.cq, cqn & (dev->limits.num_cqs - 1)); - if (cq) - atomic_inc(&cq->refcount); - spin_unlock_irq(&dev->cq_table.lock); - - if (!cq) - return; - spin_lock_irq(&cq->lock); /* @@ -301,7 +293,7 @@ void mthca_cq_clean(struct mthca_dev *dev, u32 cqn, u32 qpn, if (0) mthca_dbg(dev, "Cleaning QPN %06x from CQN %06x; ci %d, pi %d\n", - qpn, cqn, cq->cons_index, prod_index); + qpn, cq->cqn, cq->cons_index, prod_index); /* * Now sweep backwards through the CQ, removing CQ entries @@ -325,8 +317,6 @@ void mthca_cq_clean(struct mthca_dev *dev, u32 cqn, u32 qpn, } spin_unlock_irq(&cq->lock); - if (atomic_dec_and_test(&cq->refcount)) - wake_up(&cq->wait); } void mthca_cq_resize_copy_cqes(struct mthca_cq *cq) @@ -821,7 +811,7 @@ int mthca_init_cq(struct mthca_dev *dev, int nent, } spin_lock_init(&cq->lock); - atomic_set(&cq->refcount, 1); + cq->refcount = 1; init_waitqueue_head(&cq->wait); memset(cq_context, 0, sizeof *cq_context); @@ -896,6 +886,17 @@ err_out: return err; } +static inline int get_cq_refcount(struct mthca_dev *dev, struct mthca_cq *cq) +{ + int c; + + spin_lock_irq(&dev->cq_table.lock); + c = cq->refcount; + spin_unlock_irq(&dev->cq_table.lock); + + return c; +} + void mthca_free_cq(struct mthca_dev *dev, struct mthca_cq *cq) { @@ -929,6 +930,7 @@ void mthca_free_cq(struct mthca_dev *dev, spin_lock_irq(&dev->cq_table.lock); mthca_array_clear(&dev->cq_table.cq, cq->cqn & (dev->limits.num_cqs - 1)); + --cq->refcount; spin_unlock_irq(&dev->cq_table.lock); if (dev->mthca_flags & MTHCA_FLAG_MSI_X) @@ -936,8 +938,7 @@ void mthca_free_cq(struct mthca_dev *dev, else synchronize_irq(dev->pdev->irq); - atomic_dec(&cq->refcount); - wait_event(cq->wait, !atomic_read(&cq->refcount)); + wait_event(cq->wait, !get_cq_refcount(dev, cq)); if (cq->is_kernel) { mthca_free_cq_buf(dev, &cq->buf, cq->ibcq.cqe); diff --git a/drivers/infiniband/hw/mthca/mthca_dev.h b/drivers/infiniband/hw/mthca/mthca_dev.h index 4c1dcb4c182..f8160b8de09 100644 --- a/drivers/infiniband/hw/mthca/mthca_dev.h +++ b/drivers/infiniband/hw/mthca/mthca_dev.h @@ -496,7 +496,7 @@ void mthca_free_cq(struct mthca_dev *dev, void mthca_cq_completion(struct mthca_dev *dev, u32 cqn); void mthca_cq_event(struct mthca_dev *dev, u32 cqn, enum ib_event_type event_type); -void mthca_cq_clean(struct mthca_dev *dev, u32 cqn, u32 qpn, +void mthca_cq_clean(struct mthca_dev *dev, struct mthca_cq *cq, u32 qpn, struct mthca_srq *srq); void mthca_cq_resize_copy_cqes(struct mthca_cq *cq); int mthca_alloc_cq_buf(struct mthca_dev *dev, struct mthca_cq_buf *buf, int nent); diff --git a/drivers/infiniband/hw/mthca/mthca_mr.c b/drivers/infiniband/hw/mthca/mthca_mr.c index 25e1c1db9a4..a486dec1707 100644 --- a/drivers/infiniband/hw/mthca/mthca_mr.c +++ b/drivers/infiniband/hw/mthca/mthca_mr.c @@ -761,6 +761,7 @@ void mthca_arbel_fmr_unmap(struct mthca_dev *dev, struct mthca_fmr *fmr) int __devinit mthca_init_mr_table(struct mthca_dev *dev) { + unsigned long addr; int err, i; err = mthca_alloc_init(&dev->mr_table.mpt_alloc, @@ -796,9 +797,12 @@ int __devinit mthca_init_mr_table(struct mthca_dev *dev) goto err_fmr_mpt; } + addr = pci_resource_start(dev->pdev, 4) + + ((pci_resource_len(dev->pdev, 4) - 1) & + dev->mr_table.mpt_base); + dev->mr_table.tavor_fmr.mpt_base = - ioremap(dev->mr_table.mpt_base, - (1 << i) * sizeof (struct mthca_mpt_entry)); + ioremap(addr, (1 << i) * sizeof(struct mthca_mpt_entry)); if (!dev->mr_table.tavor_fmr.mpt_base) { mthca_warn(dev, "MPT ioremap for FMR failed.\n"); @@ -806,9 +810,12 @@ int __devinit mthca_init_mr_table(struct mthca_dev *dev) goto err_fmr_mpt; } + addr = pci_resource_start(dev->pdev, 4) + + ((pci_resource_len(dev->pdev, 4) - 1) & + dev->mr_table.mtt_base); + dev->mr_table.tavor_fmr.mtt_base = - ioremap(dev->mr_table.mtt_base, - (1 << i) * MTHCA_MTT_SEG_SIZE); + ioremap(addr, (1 << i) * MTHCA_MTT_SEG_SIZE); if (!dev->mr_table.tavor_fmr.mtt_base) { mthca_warn(dev, "MTT ioremap for FMR failed.\n"); err = -ENOMEM; diff --git a/drivers/infiniband/hw/mthca/mthca_provider.c b/drivers/infiniband/hw/mthca/mthca_provider.c index 565a24b1756..a2eae8a3016 100644 --- a/drivers/infiniband/hw/mthca/mthca_provider.c +++ b/drivers/infiniband/hw/mthca/mthca_provider.c @@ -306,7 +306,7 @@ static int mthca_query_gid(struct ib_device *ibdev, u8 port, goto out; } - memcpy(gid->raw + 8, out_mad->data + (index % 8) * 16, 8); + memcpy(gid->raw + 8, out_mad->data + (index % 8) * 8, 8); out: kfree(in_mad); diff --git a/drivers/infiniband/hw/mthca/mthca_provider.h b/drivers/infiniband/hw/mthca/mthca_provider.h index 6676a786d69..179a8f610d0 100644 --- a/drivers/infiniband/hw/mthca/mthca_provider.h +++ b/drivers/infiniband/hw/mthca/mthca_provider.h @@ -139,11 +139,12 @@ struct mthca_ah { * a qp may be locked, with the send cq locked first. No other * nesting should be done. * - * Each struct mthca_cq/qp also has an atomic_t ref count. The - * pointer from the cq/qp_table to the struct counts as one reference. - * This reference also is good for access through the consumer API, so - * modifying the CQ/QP etc doesn't need to take another reference. - * Access because of a completion being polled does need a reference. + * Each struct mthca_cq/qp also has an ref count, protected by the + * corresponding table lock. The pointer from the cq/qp_table to the + * struct counts as one reference. This reference also is good for + * access through the consumer API, so modifying the CQ/QP etc doesn't + * need to take another reference. Access to a QP because of a + * completion being polled does not need a reference either. * * Finally, each struct mthca_cq/qp has a wait_queue_head_t for the * destroy function to sleep on. @@ -159,8 +160,9 @@ struct mthca_ah { * - decrement ref count; if zero, wake up waiters * * To destroy a CQ/QP, we can do the following: - * - lock cq/qp_table, remove pointer, unlock cq/qp_table lock - * - decrement ref count + * - lock cq/qp_table + * - remove pointer and decrement ref count + * - unlock cq/qp_table lock * - wait_event until ref count is zero * * It is the consumer's responsibilty to make sure that no QP @@ -197,7 +199,7 @@ struct mthca_cq_resize { struct mthca_cq { struct ib_cq ibcq; spinlock_t lock; - atomic_t refcount; + int refcount; int cqn; u32 cons_index; struct mthca_cq_buf buf; @@ -217,7 +219,7 @@ struct mthca_cq { struct mthca_srq { struct ib_srq ibsrq; spinlock_t lock; - atomic_t refcount; + int refcount; int srqn; int max; int max_gs; @@ -254,7 +256,7 @@ struct mthca_wq { struct mthca_qp { struct ib_qp ibqp; - atomic_t refcount; + int refcount; u32 qpn; int is_direct; u8 port; /* for SQP and memfree use only */ diff --git a/drivers/infiniband/hw/mthca/mthca_qp.c b/drivers/infiniband/hw/mthca/mthca_qp.c index f37b0e36732..19765f6f8d5 100644 --- a/drivers/infiniband/hw/mthca/mthca_qp.c +++ b/drivers/infiniband/hw/mthca/mthca_qp.c @@ -240,7 +240,7 @@ void mthca_qp_event(struct mthca_dev *dev, u32 qpn, spin_lock(&dev->qp_table.lock); qp = mthca_array_get(&dev->qp_table.qp, qpn & (dev->limits.num_qps - 1)); if (qp) - atomic_inc(&qp->refcount); + ++qp->refcount; spin_unlock(&dev->qp_table.lock); if (!qp) { @@ -257,8 +257,10 @@ void mthca_qp_event(struct mthca_dev *dev, u32 qpn, if (qp->ibqp.event_handler) qp->ibqp.event_handler(&event, qp->ibqp.qp_context); - if (atomic_dec_and_test(&qp->refcount)) + spin_lock(&dev->qp_table.lock); + if (!--qp->refcount) wake_up(&qp->wait); + spin_unlock(&dev->qp_table.lock); } static int to_mthca_state(enum ib_qp_state ib_state) @@ -833,10 +835,10 @@ int mthca_modify_qp(struct ib_qp *ibqp, struct ib_qp_attr *attr, int attr_mask) * entries and reinitialize the QP. */ if (new_state == IB_QPS_RESET && !qp->ibqp.uobject) { - mthca_cq_clean(dev, to_mcq(qp->ibqp.send_cq)->cqn, qp->qpn, + mthca_cq_clean(dev, to_mcq(qp->ibqp.send_cq), qp->qpn, qp->ibqp.srq ? to_msrq(qp->ibqp.srq) : NULL); if (qp->ibqp.send_cq != qp->ibqp.recv_cq) - mthca_cq_clean(dev, to_mcq(qp->ibqp.recv_cq)->cqn, qp->qpn, + mthca_cq_clean(dev, to_mcq(qp->ibqp.recv_cq), qp->qpn, qp->ibqp.srq ? to_msrq(qp->ibqp.srq) : NULL); mthca_wq_init(&qp->sq); @@ -1096,7 +1098,7 @@ static int mthca_alloc_qp_common(struct mthca_dev *dev, int ret; int i; - atomic_set(&qp->refcount, 1); + qp->refcount = 1; init_waitqueue_head(&qp->wait); qp->state = IB_QPS_RESET; qp->atomic_rd_en = 0; @@ -1318,6 +1320,17 @@ int mthca_alloc_sqp(struct mthca_dev *dev, return err; } +static inline int get_qp_refcount(struct mthca_dev *dev, struct mthca_qp *qp) +{ + int c; + + spin_lock_irq(&dev->qp_table.lock); + c = qp->refcount; + spin_unlock_irq(&dev->qp_table.lock); + + return c; +} + void mthca_free_qp(struct mthca_dev *dev, struct mthca_qp *qp) { @@ -1339,14 +1352,14 @@ void mthca_free_qp(struct mthca_dev *dev, spin_lock(&dev->qp_table.lock); mthca_array_clear(&dev->qp_table.qp, qp->qpn & (dev->limits.num_qps - 1)); + --qp->refcount; spin_unlock(&dev->qp_table.lock); if (send_cq != recv_cq) spin_unlock(&recv_cq->lock); spin_unlock_irq(&send_cq->lock); - atomic_dec(&qp->refcount); - wait_event(qp->wait, !atomic_read(&qp->refcount)); + wait_event(qp->wait, !get_qp_refcount(dev, qp)); if (qp->state != IB_QPS_RESET) mthca_MODIFY_QP(dev, qp->state, IB_QPS_RESET, qp->qpn, 0, @@ -1358,10 +1371,10 @@ void mthca_free_qp(struct mthca_dev *dev, * unref the mem-free tables and free the QPN in our table. */ if (!qp->ibqp.uobject) { - mthca_cq_clean(dev, to_mcq(qp->ibqp.send_cq)->cqn, qp->qpn, + mthca_cq_clean(dev, to_mcq(qp->ibqp.send_cq), qp->qpn, qp->ibqp.srq ? to_msrq(qp->ibqp.srq) : NULL); if (qp->ibqp.send_cq != qp->ibqp.recv_cq) - mthca_cq_clean(dev, to_mcq(qp->ibqp.recv_cq)->cqn, qp->qpn, + mthca_cq_clean(dev, to_mcq(qp->ibqp.recv_cq), qp->qpn, qp->ibqp.srq ? to_msrq(qp->ibqp.srq) : NULL); mthca_free_memfree(dev, qp); diff --git a/drivers/infiniband/hw/mthca/mthca_srq.c b/drivers/infiniband/hw/mthca/mthca_srq.c index adcaf85355a..1ea433291fa 100644 --- a/drivers/infiniband/hw/mthca/mthca_srq.c +++ b/drivers/infiniband/hw/mthca/mthca_srq.c @@ -241,7 +241,7 @@ int mthca_alloc_srq(struct mthca_dev *dev, struct mthca_pd *pd, goto err_out_mailbox; spin_lock_init(&srq->lock); - atomic_set(&srq->refcount, 1); + srq->refcount = 1; init_waitqueue_head(&srq->wait); if (mthca_is_memfree(dev)) @@ -308,6 +308,17 @@ err_out: return err; } +static inline int get_srq_refcount(struct mthca_dev *dev, struct mthca_srq *srq) +{ + int c; + + spin_lock_irq(&dev->srq_table.lock); + c = srq->refcount; + spin_unlock_irq(&dev->srq_table.lock); + + return c; +} + void mthca_free_srq(struct mthca_dev *dev, struct mthca_srq *srq) { struct mthca_mailbox *mailbox; @@ -329,10 +340,10 @@ void mthca_free_srq(struct mthca_dev *dev, struct mthca_srq *srq) spin_lock_irq(&dev->srq_table.lock); mthca_array_clear(&dev->srq_table.srq, srq->srqn & (dev->limits.num_srqs - 1)); + --srq->refcount; spin_unlock_irq(&dev->srq_table.lock); - atomic_dec(&srq->refcount); - wait_event(srq->wait, !atomic_read(&srq->refcount)); + wait_event(srq->wait, !get_srq_refcount(dev, srq)); if (!srq->ibsrq.uobject) { mthca_free_srq_buf(dev, srq); @@ -414,7 +425,7 @@ void mthca_srq_event(struct mthca_dev *dev, u32 srqn, spin_lock(&dev->srq_table.lock); srq = mthca_array_get(&dev->srq_table.srq, srqn & (dev->limits.num_srqs - 1)); if (srq) - atomic_inc(&srq->refcount); + ++srq->refcount; spin_unlock(&dev->srq_table.lock); if (!srq) { @@ -431,8 +442,10 @@ void mthca_srq_event(struct mthca_dev *dev, u32 srqn, srq->ibsrq.event_handler(&event, srq->ibsrq.srq_context); out: - if (atomic_dec_and_test(&srq->refcount)) + spin_lock(&dev->srq_table.lock); + if (!--srq->refcount) wake_up(&srq->wait); + spin_unlock(&dev->srq_table.lock); } /* diff --git a/drivers/infiniband/ulp/ipoib/ipoib_vlan.c b/drivers/infiniband/ulp/ipoib/ipoib_vlan.c index 4ca175553f9..f887780e809 100644 --- a/drivers/infiniband/ulp/ipoib/ipoib_vlan.c +++ b/drivers/infiniband/ulp/ipoib/ipoib_vlan.c @@ -158,10 +158,8 @@ int ipoib_vlan_delete(struct net_device *pdev, unsigned short pkey) if (priv->pkey == pkey) { unregister_netdev(priv->dev); ipoib_dev_cleanup(priv->dev); - list_del(&priv->list); - - kfree(priv); + free_netdev(priv->dev); ret = 0; break; diff --git a/drivers/infiniband/ulp/srp/ib_srp.c b/drivers/infiniband/ulp/srp/ib_srp.c index 5bb55742ada..c32ce4348e1 100644 --- a/drivers/infiniband/ulp/srp/ib_srp.c +++ b/drivers/infiniband/ulp/srp/ib_srp.c @@ -409,6 +409,34 @@ static int srp_connect_target(struct srp_target_port *target) } } +static void srp_unmap_data(struct scsi_cmnd *scmnd, + struct srp_target_port *target, + struct srp_request *req) +{ + struct scatterlist *scat; + int nents; + + if (!scmnd->request_buffer || + (scmnd->sc_data_direction != DMA_TO_DEVICE && + scmnd->sc_data_direction != DMA_FROM_DEVICE)) + return; + + /* + * This handling of non-SG commands can be killed when the + * SCSI midlayer no longer generates non-SG commands. + */ + if (likely(scmnd->use_sg)) { + nents = scmnd->use_sg; + scat = scmnd->request_buffer; + } else { + nents = 1; + scat = &req->fake_sg; + } + + dma_unmap_sg(target->srp_host->dev->dma_device, scat, nents, + scmnd->sc_data_direction); +} + static int srp_reconnect_target(struct srp_target_port *target) { struct ib_cm_id *new_cm_id; @@ -455,16 +483,16 @@ static int srp_reconnect_target(struct srp_target_port *target) list_for_each_entry(req, &target->req_queue, list) { req->scmnd->result = DID_RESET << 16; req->scmnd->scsi_done(req->scmnd); + srp_unmap_data(req->scmnd, target, req); } target->rx_head = 0; target->tx_head = 0; target->tx_tail = 0; - target->req_head = 0; - for (i = 0; i < SRP_SQ_SIZE - 1; ++i) - target->req_ring[i].next = i + 1; - target->req_ring[SRP_SQ_SIZE - 1].next = -1; + INIT_LIST_HEAD(&target->free_reqs); INIT_LIST_HEAD(&target->req_queue); + for (i = 0; i < SRP_SQ_SIZE; ++i) + list_add_tail(&target->req_ring[i].list, &target->free_reqs); ret = srp_connect_target(target); if (ret) @@ -589,40 +617,10 @@ static int srp_map_data(struct scsi_cmnd *scmnd, struct srp_target_port *target, return len; } -static void srp_unmap_data(struct scsi_cmnd *scmnd, - struct srp_target_port *target, - struct srp_request *req) -{ - struct scatterlist *scat; - int nents; - - if (!scmnd->request_buffer || - (scmnd->sc_data_direction != DMA_TO_DEVICE && - scmnd->sc_data_direction != DMA_FROM_DEVICE)) - return; - - /* - * This handling of non-SG commands can be killed when the - * SCSI midlayer no longer generates non-SG commands. - */ - if (likely(scmnd->use_sg)) { - nents = scmnd->use_sg; - scat = scmnd->request_buffer; - } else { - nents = 1; - scat = &req->fake_sg; - } - - dma_unmap_sg(target->srp_host->dev->dma_device, scat, nents, - scmnd->sc_data_direction); -} - -static void srp_remove_req(struct srp_target_port *target, struct srp_request *req, - int index) +static void srp_remove_req(struct srp_target_port *target, struct srp_request *req) { - list_del(&req->list); - req->next = target->req_head; - target->req_head = index; + srp_unmap_data(req->scmnd, target, req); + list_move_tail(&req->list, &target->free_reqs); } static void srp_process_rsp(struct srp_target_port *target, struct srp_rsp *rsp) @@ -647,7 +645,7 @@ static void srp_process_rsp(struct srp_target_port *target, struct srp_rsp *rsp) req->tsk_status = rsp->data[3]; complete(&req->done); } else { - scmnd = req->scmnd; + scmnd = req->scmnd; if (!scmnd) printk(KERN_ERR "Null scmnd for RSP w/tag %016llx\n", (unsigned long long) rsp->tag); @@ -665,14 +663,11 @@ static void srp_process_rsp(struct srp_target_port *target, struct srp_rsp *rsp) else if (rsp->flags & (SRP_RSP_FLAG_DIOVER | SRP_RSP_FLAG_DIUNDER)) scmnd->resid = be32_to_cpu(rsp->data_in_res_cnt); - srp_unmap_data(scmnd, target, req); - if (!req->tsk_mgmt) { - req->scmnd = NULL; scmnd->host_scribble = (void *) -1L; scmnd->scsi_done(scmnd); - srp_remove_req(target, req, rsp->tag & ~SRP_TAG_TSK_MGMT); + srp_remove_req(target, req); } else req->cmd_done = 1; } @@ -859,7 +854,6 @@ static int srp_queuecommand(struct scsi_cmnd *scmnd, struct srp_request *req; struct srp_iu *iu; struct srp_cmd *cmd; - long req_index; int len; if (target->state == SRP_TARGET_CONNECTING) @@ -879,22 +873,20 @@ static int srp_queuecommand(struct scsi_cmnd *scmnd, dma_sync_single_for_cpu(target->srp_host->dev->dma_device, iu->dma, SRP_MAX_IU_LEN, DMA_TO_DEVICE); - req_index = target->req_head; + req = list_entry(target->free_reqs.next, struct srp_request, list); scmnd->scsi_done = done; scmnd->result = 0; - scmnd->host_scribble = (void *) req_index; + scmnd->host_scribble = (void *) (long) req->index; cmd = iu->buf; memset(cmd, 0, sizeof *cmd); cmd->opcode = SRP_CMD; cmd->lun = cpu_to_be64((u64) scmnd->device->lun << 48); - cmd->tag = req_index; + cmd->tag = req->index; memcpy(cmd->cdb, scmnd->cmnd, scmnd->cmd_len); - req = &target->req_ring[req_index]; - req->scmnd = scmnd; req->cmd = iu; req->cmd_done = 0; @@ -919,8 +911,7 @@ static int srp_queuecommand(struct scsi_cmnd *scmnd, goto err_unmap; } - target->req_head = req->next; - list_add_tail(&req->list, &target->req_queue); + list_move_tail(&req->list, &target->req_queue); return 0; @@ -1143,30 +1134,20 @@ static int srp_cm_handler(struct ib_cm_id *cm_id, struct ib_cm_event *event) return 0; } -static int srp_send_tsk_mgmt(struct scsi_cmnd *scmnd, u8 func) +static int srp_send_tsk_mgmt(struct srp_target_port *target, + struct srp_request *req, u8 func) { - struct srp_target_port *target = host_to_target(scmnd->device->host); - struct srp_request *req; struct srp_iu *iu; struct srp_tsk_mgmt *tsk_mgmt; - int req_index; - int ret = FAILED; spin_lock_irq(target->scsi_host->host_lock); if (target->state == SRP_TARGET_DEAD || target->state == SRP_TARGET_REMOVED) { - scmnd->result = DID_BAD_TARGET << 16; + req->scmnd->result = DID_BAD_TARGET << 16; goto out; } - if (scmnd->host_scribble == (void *) -1L) - goto out; - - req_index = (long) scmnd->host_scribble; - printk(KERN_ERR "Abort for req_index %d\n", req_index); - - req = &target->req_ring[req_index]; init_completion(&req->done); iu = __srp_get_tx_iu(target); @@ -1177,10 +1158,10 @@ static int srp_send_tsk_mgmt(struct scsi_cmnd *scmnd, u8 func) memset(tsk_mgmt, 0, sizeof *tsk_mgmt); tsk_mgmt->opcode = SRP_TSK_MGMT; - tsk_mgmt->lun = cpu_to_be64((u64) scmnd->device->lun << 48); - tsk_mgmt->tag = req_index | SRP_TAG_TSK_MGMT; + tsk_mgmt->lun = cpu_to_be64((u64) req->scmnd->device->lun << 48); + tsk_mgmt->tag = req->index | SRP_TAG_TSK_MGMT; tsk_mgmt->tsk_mgmt_func = func; - tsk_mgmt->task_tag = req_index; + tsk_mgmt->task_tag = req->index; if (__srp_post_send(target, iu, sizeof *tsk_mgmt)) goto out; @@ -1188,37 +1169,85 @@ static int srp_send_tsk_mgmt(struct scsi_cmnd *scmnd, u8 func) req->tsk_mgmt = iu; spin_unlock_irq(target->scsi_host->host_lock); + if (!wait_for_completion_timeout(&req->done, msecs_to_jiffies(SRP_ABORT_TIMEOUT_MS))) - return FAILED; - spin_lock_irq(target->scsi_host->host_lock); + return -1; - if (req->cmd_done) { - srp_remove_req(target, req, req_index); - scmnd->scsi_done(scmnd); - } else if (!req->tsk_status) { - srp_remove_req(target, req, req_index); - scmnd->result = DID_ABORT << 16; - ret = SUCCESS; - } + return 0; out: spin_unlock_irq(target->scsi_host->host_lock); - return ret; + return -1; +} + +static int srp_find_req(struct srp_target_port *target, + struct scsi_cmnd *scmnd, + struct srp_request **req) +{ + if (scmnd->host_scribble == (void *) -1L) + return -1; + + *req = &target->req_ring[(long) scmnd->host_scribble]; + + return 0; } static int srp_abort(struct scsi_cmnd *scmnd) { + struct srp_target_port *target = host_to_target(scmnd->device->host); + struct srp_request *req; + int ret = SUCCESS; + printk(KERN_ERR "SRP abort called\n"); - return srp_send_tsk_mgmt(scmnd, SRP_TSK_ABORT_TASK); + if (srp_find_req(target, scmnd, &req)) + return FAILED; + if (srp_send_tsk_mgmt(target, req, SRP_TSK_ABORT_TASK)) + return FAILED; + + spin_lock_irq(target->scsi_host->host_lock); + + if (req->cmd_done) { + srp_remove_req(target, req); + scmnd->scsi_done(scmnd); + } else if (!req->tsk_status) { + srp_remove_req(target, req); + scmnd->result = DID_ABORT << 16; + } else + ret = FAILED; + + spin_unlock_irq(target->scsi_host->host_lock); + + return ret; } static int srp_reset_device(struct scsi_cmnd *scmnd) { + struct srp_target_port *target = host_to_target(scmnd->device->host); + struct srp_request *req, *tmp; + printk(KERN_ERR "SRP reset_device called\n"); - return srp_send_tsk_mgmt(scmnd, SRP_TSK_LUN_RESET); + if (srp_find_req(target, scmnd, &req)) + return FAILED; + if (srp_send_tsk_mgmt(target, req, SRP_TSK_LUN_RESET)) + return FAILED; + if (req->tsk_status) + return FAILED; + + spin_lock_irq(target->scsi_host->host_lock); + + list_for_each_entry_safe(req, tmp, &target->req_queue, list) + if (req->scmnd->device == scmnd->device) { + req->scmnd->result = DID_RESET << 16; + scmnd->scsi_done(scmnd); + srp_remove_req(target, req); + } + + spin_unlock_irq(target->scsi_host->host_lock); + + return SUCCESS; } static int srp_reset_host(struct scsi_cmnd *scmnd) @@ -1518,10 +1547,12 @@ static ssize_t srp_create_target(struct class_device *class_dev, INIT_WORK(&target->work, srp_reconnect_work, target); - for (i = 0; i < SRP_SQ_SIZE - 1; ++i) - target->req_ring[i].next = i + 1; - target->req_ring[SRP_SQ_SIZE - 1].next = -1; + INIT_LIST_HEAD(&target->free_reqs); INIT_LIST_HEAD(&target->req_queue); + for (i = 0; i < SRP_SQ_SIZE; ++i) { + target->req_ring[i].index = i; + list_add_tail(&target->req_ring[i].list, &target->free_reqs); + } ret = srp_parse_options(buf, target); if (ret) diff --git a/drivers/infiniband/ulp/srp/ib_srp.h b/drivers/infiniband/ulp/srp/ib_srp.h index bd7f7c3115d..c5cd43aae86 100644 --- a/drivers/infiniband/ulp/srp/ib_srp.h +++ b/drivers/infiniband/ulp/srp/ib_srp.h @@ -101,7 +101,7 @@ struct srp_request { */ struct scatterlist fake_sg; struct completion done; - short next; + short index; u8 cmd_done; u8 tsk_status; }; @@ -133,7 +133,7 @@ struct srp_target_port { unsigned tx_tail; struct srp_iu *tx_ring[SRP_SQ_SIZE + 1]; - int req_head; + struct list_head free_reqs; struct list_head req_queue; struct srp_request req_ring[SRP_SQ_SIZE]; diff --git a/drivers/input/evdev.c b/drivers/input/evdev.c index a34e3d91d9e..ba325f16d07 100644 --- a/drivers/input/evdev.c +++ b/drivers/input/evdev.c @@ -403,6 +403,27 @@ static long evdev_ioctl_handler(struct file *file, unsigned int cmd, case EVIOCGID: if (copy_to_user(p, &dev->id, sizeof(struct input_id))) return -EFAULT; + return 0; + + case EVIOCGREP: + if (!test_bit(EV_REP, dev->evbit)) + return -ENOSYS; + if (put_user(dev->rep[REP_DELAY], ip)) + return -EFAULT; + if (put_user(dev->rep[REP_PERIOD], ip + 1)) + return -EFAULT; + return 0; + + case EVIOCSREP: + if (!test_bit(EV_REP, dev->evbit)) + return -ENOSYS; + if (get_user(u, ip)) + return -EFAULT; + if (get_user(v, ip + 1)) + return -EFAULT; + + input_event(dev, EV_REP, REP_DELAY, u); + input_event(dev, EV_REP, REP_PERIOD, v); return 0; diff --git a/drivers/input/input.c b/drivers/input/input.c index a935abeffff..3038c268917 100644 --- a/drivers/input/input.c +++ b/drivers/input/input.c @@ -155,6 +155,9 @@ void input_event(struct input_dev *dev, unsigned int type, unsigned int code, in if (code > SND_MAX || !test_bit(code, dev->sndbit)) return; + if (!!test_bit(code, dev->snd) != !!value) + change_bit(code, dev->snd); + if (dev->event) dev->event(dev, type, code, value); break; @@ -286,19 +289,19 @@ static struct input_device_id *input_match_device(struct input_device_id *id, st for (; id->flags || id->driver_info; id++) { if (id->flags & INPUT_DEVICE_ID_MATCH_BUS) - if (id->id.bustype != dev->id.bustype) + if (id->bustype != dev->id.bustype) continue; if (id->flags & INPUT_DEVICE_ID_MATCH_VENDOR) - if (id->id.vendor != dev->id.vendor) + if (id->vendor != dev->id.vendor) continue; if (id->flags & INPUT_DEVICE_ID_MATCH_PRODUCT) - if (id->id.product != dev->id.product) + if (id->product != dev->id.product) continue; if (id->flags & INPUT_DEVICE_ID_MATCH_VERSION) - if (id->id.version != dev->id.version) + if (id->version != dev->id.version) continue; MATCH_BIT(evbit, EV_MAX); diff --git a/drivers/input/keyboard/spitzkbd.c b/drivers/input/keyboard/spitzkbd.c index bc61cf8cfc6..1d238a9d52d 100644 --- a/drivers/input/keyboard/spitzkbd.c +++ b/drivers/input/keyboard/spitzkbd.c @@ -53,8 +53,8 @@ static unsigned char spitzkbd_keycode[NR_SCANCODES] = { KEY_LEFTCTRL, KEY_1, KEY_3, KEY_5, KEY_6, KEY_7, KEY_9, KEY_0, KEY_BACKSPACE, SPITZ_KEY_EXOK, SPITZ_KEY_EXCANCEL, 0, 0, 0, 0, 0, /* 1-16 */ 0, KEY_2, KEY_4, KEY_R, KEY_Y, KEY_8, KEY_I, KEY_O, KEY_P, SPITZ_KEY_EXJOGDOWN, SPITZ_KEY_EXJOGUP, 0, 0, 0, 0, 0, /* 17-32 */ KEY_TAB, KEY_Q, KEY_E, KEY_T, KEY_G, KEY_U, KEY_J, KEY_K, 0, 0, 0, 0, 0, 0, 0, 0, /* 33-48 */ - SPITZ_KEY_CALENDER, KEY_W, KEY_S, KEY_F, KEY_V, KEY_H, KEY_M, KEY_L, 0, KEY_RIGHTSHIFT, 0, 0, 0, 0, 0, 0, /* 49-64 */ - SPITZ_KEY_ADDRESS, KEY_A, KEY_D, KEY_C, KEY_B, KEY_N, KEY_DOT, 0, KEY_ENTER, KEY_LEFTSHIFT, 0, 0, 0, 0, 0, 0, /* 65-80 */ + SPITZ_KEY_ADDRESS, KEY_W, KEY_S, KEY_F, KEY_V, KEY_H, KEY_M, KEY_L, 0, KEY_RIGHTSHIFT, 0, 0, 0, 0, 0, 0, /* 49-64 */ + SPITZ_KEY_CALENDER, KEY_A, KEY_D, KEY_C, KEY_B, KEY_N, KEY_DOT, 0, KEY_ENTER, KEY_LEFTSHIFT, 0, 0, 0, 0, 0, 0, /* 65-80 */ SPITZ_KEY_MAIL, KEY_Z, KEY_X, KEY_MINUS, KEY_SPACE, KEY_COMMA, 0, KEY_UP, 0, 0, SPITZ_KEY_FN, 0, 0, 0, 0, 0, /* 81-96 */ KEY_SYSRQ, SPITZ_KEY_JAP1, SPITZ_KEY_JAP2, SPITZ_KEY_CANCEL, SPITZ_KEY_OK, SPITZ_KEY_MENU, KEY_LEFT, KEY_DOWN, KEY_RIGHT, 0, 0, 0, 0, 0, 0, 0 /* 97-112 */ }; diff --git a/drivers/input/misc/wistron_btns.c b/drivers/input/misc/wistron_btns.c index 4b415d9b012..36cd2e07fce 100644 --- a/drivers/input/misc/wistron_btns.c +++ b/drivers/input/misc/wistron_btns.c @@ -273,6 +273,18 @@ static struct key_entry keymap_fs_amilo_pro_v2000[] = { { KE_END, 0 } }; +static struct key_entry keymap_fujitsu_n3510[] = { + { KE_KEY, 0x11, KEY_PROG1 }, + { KE_KEY, 0x12, KEY_PROG2 }, + { KE_KEY, 0x36, KEY_WWW }, + { KE_KEY, 0x31, KEY_MAIL }, + { KE_KEY, 0x71, KEY_STOPCD }, + { KE_KEY, 0x72, KEY_PLAYPAUSE }, + { KE_KEY, 0x74, KEY_REWIND }, + { KE_KEY, 0x78, KEY_FORWARD }, + { KE_END, 0 } +}; + static struct key_entry keymap_wistron_ms2141[] = { { KE_KEY, 0x11, KEY_PROG1 }, { KE_KEY, 0x12, KEY_PROG2 }, @@ -323,6 +335,24 @@ static struct dmi_system_id dmi_ids[] = { }, { .callback = dmi_matched, + .ident = "Fujitsu-Siemens Amilo M7400", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU SIEMENS"), + DMI_MATCH(DMI_PRODUCT_NAME, "AMILO M "), + }, + .driver_data = keymap_fs_amilo_pro_v2000 + }, + { + .callback = dmi_matched, + .ident = "Fujitsu N3510", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"), + DMI_MATCH(DMI_PRODUCT_NAME, "N3510"), + }, + .driver_data = keymap_fujitsu_n3510 + }, + { + .callback = dmi_matched, .ident = "Acer Aspire 1500", .matches = { DMI_MATCH(DMI_SYS_VENDOR, "Acer"), diff --git a/drivers/input/mouse/psmouse-base.c b/drivers/input/mouse/psmouse-base.c index 32d70ed8f41..136321a2cfd 100644 --- a/drivers/input/mouse/psmouse-base.c +++ b/drivers/input/mouse/psmouse-base.c @@ -302,8 +302,10 @@ static irqreturn_t psmouse_interrupt(struct serio *serio, * Check if this is a new device announcement (0xAA 0x00) */ if (unlikely(psmouse->packet[0] == PSMOUSE_RET_BAT && psmouse->pktcnt <= 2)) { - if (psmouse->pktcnt == 1) + if (psmouse->pktcnt == 1) { + psmouse->last = jiffies; goto out; + } if (psmouse->packet[1] == PSMOUSE_RET_ID) { __psmouse_set_state(psmouse, PSMOUSE_IGNORE); diff --git a/drivers/input/serio/i8042-io.h b/drivers/input/serio/i8042-io.h index 9a922164425..cc21914fbc7 100644 --- a/drivers/input/serio/i8042-io.h +++ b/drivers/input/serio/i8042-io.h @@ -67,14 +67,14 @@ static inline int i8042_platform_init(void) * On some platforms touching the i8042 data register region can do really * bad things. Because of this the region is always reserved on such boxes. */ -#if !defined(__sh__) && !defined(__alpha__) && !defined(__mips__) && !defined(CONFIG_PPC64) +#if !defined(__sh__) && !defined(__alpha__) && !defined(__mips__) && !defined(CONFIG_PPC_MERGE) if (!request_region(I8042_DATA_REG, 16, "i8042")) return -EBUSY; #endif i8042_reset = 1; -#if defined(CONFIG_PPC64) +#if defined(CONFIG_PPC_MERGE) if (check_legacy_ioport(I8042_DATA_REG)) return -EBUSY; if (!request_region(I8042_DATA_REG, 16, "i8042")) diff --git a/drivers/input/touchscreen/ads7846.c b/drivers/input/touchscreen/ads7846.c index 46d1fec2cfd..1494175ac6f 100644 --- a/drivers/input/touchscreen/ads7846.c +++ b/drivers/input/touchscreen/ads7846.c @@ -2,6 +2,8 @@ * ADS7846 based touchscreen and sensor driver * * Copyright (c) 2005 David Brownell + * Copyright (c) 2006 Nokia Corporation + * Various changes: Imre Deak <imre.deak@nokia.com> * * Using code from: * - corgi_ts.c @@ -34,17 +36,25 @@ /* - * This code has been lightly tested on an ads7846. + * This code has been tested on an ads7846 / N770 device. * Support for ads7843 and ads7845 has only been stubbed in. * - * Not yet done: investigate the values reported. Are x/y/pressure - * event values sane enough for X11? How accurate are the temperature - * and voltage readings? (System-specific calibration should support + * Not yet done: How accurate are the temperature and voltage + * readings? (System-specific calibration should support * accuracy of 0.3 degrees C; otherwise it's 2.0 degrees.) * + * IRQ handling needs a workaround because of a shortcoming in handling + * edge triggered IRQs on some platforms like the OMAP1/2. These + * platforms don't handle the ARM lazy IRQ disabling properly, thus we + * have to maintain our own SW IRQ disabled status. This should be + * removed as soon as the affected platform's IRQ handling is fixed. + * * app note sbaa036 talks in more detail about accurate sampling... * that ought to help in situations like LCDs inducing noise (which * can also be helped by using synch signals) and more generally. + * This driver tries to utilize the measures described in the app + * note. The strength of filtering can be set in the board-* specific + * files. */ #define TS_POLL_PERIOD msecs_to_jiffies(10) @@ -61,6 +71,7 @@ struct ts_event { __be16 x; __be16 y; __be16 z1, z2; + int ignore; }; struct ads7846 { @@ -71,12 +82,23 @@ struct ads7846 { u16 model; u16 vref_delay_usecs; u16 x_plate_ohms; + u16 pressure_max; - u8 read_x, read_y, read_z1, read_z2; + u8 read_x, read_y, read_z1, read_z2, pwrdown; + u16 dummy; /* for the pwrdown read */ struct ts_event tc; - struct spi_transfer xfer[8]; - struct spi_message msg; + struct spi_transfer xfer[10]; + struct spi_message msg[5]; + struct spi_message *last_msg; + int msg_idx; + int read_cnt; + int read_rep; + int last_read; + + u16 debounce_max; + u16 debounce_tol; + u16 debounce_rep; spinlock_t lock; struct timer_list timer; /* P: lock */ @@ -84,6 +106,9 @@ struct ads7846 { unsigned pending:1; /* P: lock */ // FIXME remove "irq_disabled" unsigned irq_disabled:1; /* P: lock */ + unsigned disabled:1; + + int (*get_pendown_state)(void); }; /* leave chip selected when we're done, for quicker re-select? */ @@ -125,7 +150,9 @@ struct ads7846 { #define READ_Y (READ_12BIT_DFR(y) | ADS_PD10_ADC_ON) #define READ_Z1 (READ_12BIT_DFR(z1) | ADS_PD10_ADC_ON) #define READ_Z2 (READ_12BIT_DFR(z2) | ADS_PD10_ADC_ON) -#define READ_X (READ_12BIT_DFR(x) | ADS_PD10_PDOWN) /* LAST */ + +#define READ_X (READ_12BIT_DFR(x) | ADS_PD10_ADC_ON) +#define PWRDOWN (READ_12BIT_DFR(y) | ADS_PD10_PDOWN) /* LAST */ /* single-ended samples need to first power up reference voltage; * we leave both ADC and VREF powered @@ -152,6 +179,15 @@ struct ser_req { struct spi_transfer xfer[6]; }; +static void ads7846_enable(struct ads7846 *ts); +static void ads7846_disable(struct ads7846 *ts); + +static int device_suspended(struct device *dev) +{ + struct ads7846 *ts = dev_get_drvdata(dev); + return dev->power.power_state.event != PM_EVENT_ON || ts->disabled; +} + static int ads7846_read12_ser(struct device *dev, unsigned command) { struct spi_device *spi = to_spi_device(dev); @@ -164,7 +200,7 @@ static int ads7846_read12_ser(struct device *dev, unsigned command) if (!req) return -ENOMEM; - INIT_LIST_HEAD(&req->msg.transfers); + spi_message_init(&req->msg); /* activate reference, so it has time to settle; */ req->ref_on = REF_ON; @@ -204,8 +240,10 @@ static int ads7846_read12_ser(struct device *dev, unsigned command) for (i = 0; i < 6; i++) spi_message_add_tail(&req->xfer[i], &req->msg); + ts->irq_disabled = 1; disable_irq(spi->irq); status = spi_sync(spi, &req->msg); + ts->irq_disabled = 0; enable_irq(spi->irq); if (req->msg.status) @@ -233,6 +271,52 @@ SHOW(temp1) SHOW(vaux) SHOW(vbatt) +static int is_pen_down(struct device *dev) +{ + struct ads7846 *ts = dev_get_drvdata(dev); + + return ts->pendown; +} + +static ssize_t ads7846_pen_down_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + return sprintf(buf, "%u\n", is_pen_down(dev)); +} + +static DEVICE_ATTR(pen_down, S_IRUGO, ads7846_pen_down_show, NULL); + +static ssize_t ads7846_disable_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct ads7846 *ts = dev_get_drvdata(dev); + + return sprintf(buf, "%u\n", ts->disabled); +} + +static ssize_t ads7846_disable_store(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct ads7846 *ts = dev_get_drvdata(dev); + char *endp; + int i; + + i = simple_strtoul(buf, &endp, 10); + spin_lock_irq(&ts->lock); + + if (i) + ads7846_disable(ts); + else + ads7846_enable(ts); + + spin_unlock_irq(&ts->lock); + + return count; +} + +static DEVICE_ATTR(disable, 0664, ads7846_disable_show, ads7846_disable_store); + /*--------------------------------------------------------------------------*/ /* @@ -264,7 +348,7 @@ static void ads7846_rx(void *ads) if (x == MAX_12BIT) x = 0; - if (x && z1 && ts->spi->dev.power.power_state.event == PM_EVENT_ON) { + if (likely(x && z1 && !device_suspended(&ts->spi->dev))) { /* compute touch pressure resistance using equation #2 */ Rt = z2; Rt -= z1; @@ -275,6 +359,14 @@ static void ads7846_rx(void *ads) } else Rt = 0; + /* Sample found inconsistent by debouncing or pressure is beyond + * the maximum. Don't report it to user space, repeat at least + * once more the measurement */ + if (ts->tc.ignore || Rt > ts->pressure_max) { + mod_timer(&ts->timer, jiffies + TS_POLL_PERIOD); + return; + } + /* NOTE: "pendown" is inferred from pressure; we don't rely on * being able to check nPENIRQ status, or "friendly" trigger modes * (both-edges is much better than just-falling or low-level). @@ -296,11 +388,13 @@ static void ads7846_rx(void *ads) if (Rt) { input_report_abs(input_dev, ABS_X, x); input_report_abs(input_dev, ABS_Y, y); - input_report_abs(input_dev, ABS_PRESSURE, Rt); sync = 1; } - if (sync) + + if (sync) { + input_report_abs(input_dev, ABS_PRESSURE, Rt); input_sync(input_dev); + } #ifdef VERBOSE if (Rt || ts->pendown) @@ -308,80 +402,138 @@ static void ads7846_rx(void *ads) x, y, Rt, Rt ? "" : " UP"); #endif - /* don't retrigger while we're suspended */ spin_lock_irqsave(&ts->lock, flags); ts->pendown = (Rt != 0); - ts->pending = 0; + mod_timer(&ts->timer, jiffies + TS_POLL_PERIOD); - if (ts->spi->dev.power.power_state.event == PM_EVENT_ON) { - if (ts->pendown) - mod_timer(&ts->timer, jiffies + TS_POLL_PERIOD); - else if (ts->irq_disabled) { - ts->irq_disabled = 0; - enable_irq(ts->spi->irq); + spin_unlock_irqrestore(&ts->lock, flags); +} + +static void ads7846_debounce(void *ads) +{ + struct ads7846 *ts = ads; + struct spi_message *m; + struct spi_transfer *t; + int val; + int status; + + m = &ts->msg[ts->msg_idx]; + t = list_entry(m->transfers.prev, struct spi_transfer, transfer_list); + val = (*(u16 *)t->rx_buf) >> 3; + if (!ts->read_cnt || (abs(ts->last_read - val) > ts->debounce_tol)) { + /* Repeat it, if this was the first read or the read + * wasn't consistent enough. */ + if (ts->read_cnt < ts->debounce_max) { + ts->last_read = val; + ts->read_cnt++; + } else { + /* Maximum number of debouncing reached and still + * not enough number of consistent readings. Abort + * the whole sample, repeat it in the next sampling + * period. + */ + ts->tc.ignore = 1; + ts->read_cnt = 0; + /* Last message will contain ads7846_rx() as the + * completion function. + */ + m = ts->last_msg; } + /* Start over collecting consistent readings. */ + ts->read_rep = 0; + } else { + if (++ts->read_rep > ts->debounce_rep) { + /* Got a good reading for this coordinate, + * go for the next one. */ + ts->tc.ignore = 0; + ts->msg_idx++; + ts->read_cnt = 0; + ts->read_rep = 0; + m++; + } else + /* Read more values that are consistent. */ + ts->read_cnt++; } - - spin_unlock_irqrestore(&ts->lock, flags); + status = spi_async(ts->spi, m); + if (status) + dev_err(&ts->spi->dev, "spi_async --> %d\n", + status); } static void ads7846_timer(unsigned long handle) { struct ads7846 *ts = (void *)handle; int status = 0; - unsigned long flags; + + spin_lock_irq(&ts->lock); + + if (unlikely(ts->msg_idx && !ts->pendown)) { + /* measurment cycle ended */ + if (!device_suspended(&ts->spi->dev)) { + ts->irq_disabled = 0; + enable_irq(ts->spi->irq); + } + ts->pending = 0; + ts->msg_idx = 0; + } else { + /* pen is still down, continue with the measurement */ + ts->msg_idx = 0; + status = spi_async(ts->spi, &ts->msg[0]); + if (status) + dev_err(&ts->spi->dev, "spi_async --> %d\n", status); + } + + spin_unlock_irq(&ts->lock); +} + +static irqreturn_t ads7846_irq(int irq, void *handle, struct pt_regs *regs) +{ + struct ads7846 *ts = handle; + unsigned long flags; spin_lock_irqsave(&ts->lock, flags); - if (!ts->pending) { - ts->pending = 1; + if (likely(ts->get_pendown_state())) { if (!ts->irq_disabled) { + /* REVISIT irq logic for many ARM chips has cloned a + * bug wherein disabling an irq in its handler won't + * work;(it's disabled lazily, and too late to work. + * until all their irq logic is fixed, we must shadow + * that state here. + */ ts->irq_disabled = 1; disable_irq(ts->spi->irq); + ts->pending = 1; + mod_timer(&ts->timer, jiffies); } - status = spi_async(ts->spi, &ts->msg); - if (status) - dev_err(&ts->spi->dev, "spi_async --> %d\n", - status); } spin_unlock_irqrestore(&ts->lock, flags); -} -static irqreturn_t ads7846_irq(int irq, void *handle, struct pt_regs *regs) -{ - ads7846_timer((unsigned long) handle); return IRQ_HANDLED; } /*--------------------------------------------------------------------------*/ -static int -ads7846_suspend(struct spi_device *spi, pm_message_t message) +/* Must be called with ts->lock held */ +static void ads7846_disable(struct ads7846 *ts) { - struct ads7846 *ts = dev_get_drvdata(&spi->dev); - unsigned long flags; + if (ts->disabled) + return; - spin_lock_irqsave(&ts->lock, flags); - - spi->dev.power.power_state = message; + ts->disabled = 1; /* are we waiting for IRQ, or polling? */ - if (!ts->pendown) { - if (!ts->irq_disabled) { - ts->irq_disabled = 1; - disable_irq(ts->spi->irq); - } + if (!ts->pending) { + ts->irq_disabled = 1; + disable_irq(ts->spi->irq); } else { - /* polling; force a final SPI completion; - * that will clean things up neatly + /* the timer will run at least once more, and + * leave everything in a clean state, IRQ disabled */ - if (!ts->pending) - mod_timer(&ts->timer, jiffies); - - while (ts->pendown || ts->pending) { - spin_unlock_irqrestore(&ts->lock, flags); - udelay(10); - spin_lock_irqsave(&ts->lock, flags); + while (ts->pending) { + spin_unlock_irq(&ts->lock); + msleep(1); + spin_lock_irq(&ts->lock); } } @@ -389,17 +541,45 @@ ads7846_suspend(struct spi_device *spi, pm_message_t message) * leave it that way after every request */ - spin_unlock_irqrestore(&ts->lock, flags); +} + +/* Must be called with ts->lock held */ +static void ads7846_enable(struct ads7846 *ts) +{ + if (!ts->disabled) + return; + + ts->disabled = 0; + ts->irq_disabled = 0; + enable_irq(ts->spi->irq); +} + +static int ads7846_suspend(struct spi_device *spi, pm_message_t message) +{ + struct ads7846 *ts = dev_get_drvdata(&spi->dev); + + spin_lock_irq(&ts->lock); + + spi->dev.power.power_state = message; + ads7846_disable(ts); + + spin_unlock_irq(&ts->lock); + return 0; + } static int ads7846_resume(struct spi_device *spi) { struct ads7846 *ts = dev_get_drvdata(&spi->dev); - ts->irq_disabled = 0; - enable_irq(ts->spi->irq); + spin_lock_irq(&ts->lock); + spi->dev.power.power_state = PMSG_ON; + ads7846_enable(ts); + + spin_unlock_irq(&ts->lock); + return 0; } @@ -408,6 +588,7 @@ static int __devinit ads7846_probe(struct spi_device *spi) struct ads7846 *ts; struct input_dev *input_dev; struct ads7846_platform_data *pdata = spi->dev.platform_data; + struct spi_message *m; struct spi_transfer *x; int err; @@ -428,6 +609,11 @@ static int __devinit ads7846_probe(struct spi_device *spi) return -EINVAL; } + if (pdata->get_pendown_state == NULL) { + dev_dbg(&spi->dev, "no get_pendown_state function?\n"); + return -EINVAL; + } + /* We'd set the wordsize to 12 bits ... except that some controllers * will then treat the 8 bit command words as 12 bits (and drop the * four MSBs of the 12 bit result). Result: inputs must be shifted @@ -451,9 +637,21 @@ static int __devinit ads7846_probe(struct spi_device *spi) ts->timer.data = (unsigned long) ts; ts->timer.function = ads7846_timer; + spin_lock_init(&ts->lock); + ts->model = pdata->model ? : 7846; ts->vref_delay_usecs = pdata->vref_delay_usecs ? : 100; ts->x_plate_ohms = pdata->x_plate_ohms ? : 400; + ts->pressure_max = pdata->pressure_max ? : ~0; + if (pdata->debounce_max) { + ts->debounce_max = pdata->debounce_max; + ts->debounce_tol = pdata->debounce_tol; + ts->debounce_rep = pdata->debounce_rep; + if (ts->debounce_rep > ts->debounce_max + 1) + ts->debounce_rep = ts->debounce_max - 1; + } else + ts->debounce_tol = ~0; + ts->get_pendown_state = pdata->get_pendown_state; snprintf(ts->phys, sizeof(ts->phys), "%s/input0", spi->dev.bus_id); @@ -477,60 +675,100 @@ static int __devinit ads7846_probe(struct spi_device *spi) /* set up the transfers to read touchscreen state; this assumes we * use formula #2 for pressure, not #3. */ - INIT_LIST_HEAD(&ts->msg.transfers); + m = &ts->msg[0]; x = ts->xfer; + spi_message_init(m); + /* y- still on; turn on only y+ (and ADC) */ ts->read_y = READ_Y; x->tx_buf = &ts->read_y; x->len = 1; - spi_message_add_tail(x, &ts->msg); + spi_message_add_tail(x, m); x++; x->rx_buf = &ts->tc.y; x->len = 2; - spi_message_add_tail(x, &ts->msg); + spi_message_add_tail(x, m); + + m->complete = ads7846_debounce; + m->context = ts; + + m++; + spi_message_init(m); + + /* turn y- off, x+ on, then leave in lowpower */ + x++; + ts->read_x = READ_X; + x->tx_buf = &ts->read_x; + x->len = 1; + spi_message_add_tail(x, m); + + x++; + x->rx_buf = &ts->tc.x; + x->len = 2; + spi_message_add_tail(x, m); + + m->complete = ads7846_debounce; + m->context = ts; /* turn y+ off, x- on; we'll use formula #2 */ if (ts->model == 7846) { + m++; + spi_message_init(m); + x++; ts->read_z1 = READ_Z1; x->tx_buf = &ts->read_z1; x->len = 1; - spi_message_add_tail(x, &ts->msg); + spi_message_add_tail(x, m); x++; x->rx_buf = &ts->tc.z1; x->len = 2; - spi_message_add_tail(x, &ts->msg); + spi_message_add_tail(x, m); + + m->complete = ads7846_debounce; + m->context = ts; + + m++; + spi_message_init(m); x++; ts->read_z2 = READ_Z2; x->tx_buf = &ts->read_z2; x->len = 1; - spi_message_add_tail(x, &ts->msg); + spi_message_add_tail(x, m); x++; x->rx_buf = &ts->tc.z2; x->len = 2; - spi_message_add_tail(x, &ts->msg); + spi_message_add_tail(x, m); + + m->complete = ads7846_debounce; + m->context = ts; } - /* turn y- off, x+ on, then leave in lowpower */ + /* power down */ + m++; + spi_message_init(m); + x++; - ts->read_x = READ_X; - x->tx_buf = &ts->read_x; + ts->pwrdown = PWRDOWN; + x->tx_buf = &ts->pwrdown; x->len = 1; - spi_message_add_tail(x, &ts->msg); + spi_message_add_tail(x, m); x++; - x->rx_buf = &ts->tc.x; + x->rx_buf = &ts->dummy; x->len = 2; CS_CHANGE(*x); - spi_message_add_tail(x, &ts->msg); + spi_message_add_tail(x, m); - ts->msg.complete = ads7846_rx; - ts->msg.context = ts; + m->complete = ads7846_rx; + m->context = ts; + + ts->last_msg = m; if (request_irq(spi->irq, ads7846_irq, SA_SAMPLE_RANDOM | SA_TRIGGER_FALLING, @@ -559,13 +797,27 @@ static int __devinit ads7846_probe(struct spi_device *spi) device_create_file(&spi->dev, &dev_attr_vbatt); device_create_file(&spi->dev, &dev_attr_vaux); + device_create_file(&spi->dev, &dev_attr_pen_down); + + device_create_file(&spi->dev, &dev_attr_disable); + err = input_register_device(input_dev); if (err) - goto err_free_irq; + goto err_remove_attr; return 0; - err_free_irq: + err_remove_attr: + device_remove_file(&spi->dev, &dev_attr_disable); + device_remove_file(&spi->dev, &dev_attr_pen_down); + if (ts->model == 7846) { + device_remove_file(&spi->dev, &dev_attr_temp1); + device_remove_file(&spi->dev, &dev_attr_temp0); + } + if (ts->model != 7845) + device_remove_file(&spi->dev, &dev_attr_vbatt); + device_remove_file(&spi->dev, &dev_attr_vaux); + free_irq(spi->irq, ts); err_free_mem: input_free_device(input_dev); @@ -577,20 +829,24 @@ static int __devexit ads7846_remove(struct spi_device *spi) { struct ads7846 *ts = dev_get_drvdata(&spi->dev); + input_unregister_device(ts->input); + ads7846_suspend(spi, PMSG_SUSPEND); - free_irq(ts->spi->irq, ts); - if (ts->irq_disabled) - enable_irq(ts->spi->irq); + device_remove_file(&spi->dev, &dev_attr_disable); + device_remove_file(&spi->dev, &dev_attr_pen_down); if (ts->model == 7846) { - device_remove_file(&spi->dev, &dev_attr_temp0); device_remove_file(&spi->dev, &dev_attr_temp1); + device_remove_file(&spi->dev, &dev_attr_temp0); } if (ts->model != 7845) device_remove_file(&spi->dev, &dev_attr_vbatt); device_remove_file(&spi->dev, &dev_attr_vaux); - input_unregister_device(ts->input); + free_irq(ts->spi->irq, ts); + /* suspend left the IRQ disabled */ + enable_irq(ts->spi->irq); + kfree(ts); dev_dbg(&spi->dev, "unregistered touchscreen\n"); diff --git a/drivers/input/touchscreen/corgi_ts.c b/drivers/input/touchscreen/corgi_ts.c index 1042987856f..5013703db0e 100644 --- a/drivers/input/touchscreen/corgi_ts.c +++ b/drivers/input/touchscreen/corgi_ts.c @@ -17,7 +17,7 @@ #include <linux/interrupt.h> #include <linux/module.h> #include <linux/slab.h> -#include <asm/irq.h> +//#include <asm/irq.h> #include <asm/arch/sharpsl.h> #include <asm/arch/hardware.h> diff --git a/drivers/md/raid1.c b/drivers/md/raid1.c index 6081941de1b..4070eff6f0f 100644 --- a/drivers/md/raid1.c +++ b/drivers/md/raid1.c @@ -315,10 +315,11 @@ static int raid1_end_write_request(struct bio *bio, unsigned int bytes_done, int if (r1_bio->bios[mirror] == bio) break; - if (error == -ENOTSUPP && test_bit(R1BIO_Barrier, &r1_bio->state)) { + if (error == -EOPNOTSUPP && test_bit(R1BIO_Barrier, &r1_bio->state)) { set_bit(BarriersNotsupp, &conf->mirrors[mirror].rdev->flags); set_bit(R1BIO_BarrierRetry, &r1_bio->state); r1_bio->mddev->barriers_work = 0; + /* Don't rdev_dec_pending in this branch - keep it for the retry */ } else { /* * this branch is our 'one mirror IO has finished' event handler: @@ -365,6 +366,7 @@ static int raid1_end_write_request(struct bio *bio, unsigned int bytes_done, int } } } + rdev_dec_pending(conf->mirrors[mirror].rdev, conf->mddev); } /* * @@ -374,11 +376,9 @@ static int raid1_end_write_request(struct bio *bio, unsigned int bytes_done, int if (atomic_dec_and_test(&r1_bio->remaining)) { if (test_bit(R1BIO_BarrierRetry, &r1_bio->state)) { reschedule_retry(r1_bio); - /* Don't dec_pending yet, we want to hold - * the reference over the retry - */ goto out; } + /* it really is the end of this request */ if (test_bit(R1BIO_BehindIO, &r1_bio->state)) { /* free extra copy of the data pages */ int i = bio->bi_vcnt; @@ -393,8 +393,6 @@ static int raid1_end_write_request(struct bio *bio, unsigned int bytes_done, int md_write_end(r1_bio->mddev); raid_end_bio_io(r1_bio); } - - rdev_dec_pending(conf->mirrors[mirror].rdev, conf->mddev); out: if (to_put) bio_put(to_put); @@ -753,18 +751,24 @@ static int make_request(request_queue_t *q, struct bio * bio) const int rw = bio_data_dir(bio); int do_barriers; - if (unlikely(!mddev->barriers_work && bio_barrier(bio))) { - bio_endio(bio, bio->bi_size, -EOPNOTSUPP); - return 0; - } - /* * Register the new request and wait if the reconstruction * thread has put up a bar for new requests. * Continue immediately if no resync is active currently. + * We test barriers_work *after* md_write_start as md_write_start + * may cause the first superblock write, and that will check out + * if barriers work. */ + md_write_start(mddev, bio); /* wait on superblock update early */ + if (unlikely(!mddev->barriers_work && bio_barrier(bio))) { + if (rw == WRITE) + md_write_end(mddev); + bio_endio(bio, bio->bi_size, -EOPNOTSUPP); + return 0; + } + wait_barrier(conf); disk_stat_inc(mddev->gendisk, ios[rw]); @@ -1404,10 +1408,11 @@ static void raid1d(mddev_t *mddev) unplug = 1; } else if (test_bit(R1BIO_BarrierRetry, &r1_bio->state)) { /* some requests in the r1bio were BIO_RW_BARRIER - * requests which failed with -ENOTSUPP. Hohumm.. + * requests which failed with -EOPNOTSUPP. Hohumm.. * Better resubmit without the barrier. * We know which devices to resubmit for, because * all others have had their bios[] entry cleared. + * We already have a nr_pending reference on these rdevs. */ int i; clear_bit(R1BIO_BarrierRetry, &r1_bio->state); diff --git a/drivers/md/raid10.c b/drivers/md/raid10.c index 617012bc107..1440935414e 100644 --- a/drivers/md/raid10.c +++ b/drivers/md/raid10.c @@ -1407,43 +1407,54 @@ static void raid10d(mddev_t *mddev) if (s > (PAGE_SIZE>>9)) s = PAGE_SIZE >> 9; + rcu_read_lock(); do { int d = r10_bio->devs[sl].devnum; - rdev = conf->mirrors[d].rdev; + rdev = rcu_dereference(conf->mirrors[d].rdev); if (rdev && - test_bit(In_sync, &rdev->flags) && - sync_page_io(rdev->bdev, - r10_bio->devs[sl].addr + - sect + rdev->data_offset, - s<<9, - conf->tmppage, READ)) - success = 1; - else { - sl++; - if (sl == conf->copies) - sl = 0; + test_bit(In_sync, &rdev->flags)) { + atomic_inc(&rdev->nr_pending); + rcu_read_unlock(); + success = sync_page_io(rdev->bdev, + r10_bio->devs[sl].addr + + sect + rdev->data_offset, + s<<9, + conf->tmppage, READ); + rdev_dec_pending(rdev, mddev); + rcu_read_lock(); + if (success) + break; } + sl++; + if (sl == conf->copies) + sl = 0; } while (!success && sl != r10_bio->read_slot); + rcu_read_unlock(); if (success) { int start = sl; /* write it back and re-read */ + rcu_read_lock(); while (sl != r10_bio->read_slot) { int d; if (sl==0) sl = conf->copies; sl--; d = r10_bio->devs[sl].devnum; - rdev = conf->mirrors[d].rdev; - atomic_add(s, &rdev->corrected_errors); + rdev = rcu_dereference(conf->mirrors[d].rdev); if (rdev && test_bit(In_sync, &rdev->flags)) { + atomic_inc(&rdev->nr_pending); + rcu_read_unlock(); + atomic_add(s, &rdev->corrected_errors); if (sync_page_io(rdev->bdev, r10_bio->devs[sl].addr + sect + rdev->data_offset, s<<9, conf->tmppage, WRITE) == 0) /* Well, this device is dead */ md_error(mddev, rdev); + rdev_dec_pending(rdev, mddev); + rcu_read_lock(); } } sl = start; @@ -1453,17 +1464,22 @@ static void raid10d(mddev_t *mddev) sl = conf->copies; sl--; d = r10_bio->devs[sl].devnum; - rdev = conf->mirrors[d].rdev; + rdev = rcu_dereference(conf->mirrors[d].rdev); if (rdev && test_bit(In_sync, &rdev->flags)) { + atomic_inc(&rdev->nr_pending); + rcu_read_unlock(); if (sync_page_io(rdev->bdev, r10_bio->devs[sl].addr + sect + rdev->data_offset, s<<9, conf->tmppage, READ) == 0) /* Well, this device is dead */ md_error(mddev, rdev); + rdev_dec_pending(rdev, mddev); + rcu_read_lock(); } } + rcu_read_unlock(); } else { /* Cannot read from anywhere -- bye bye array */ md_error(mddev, conf->mirrors[r10_bio->devs[r10_bio->read_slot].devnum].rdev); diff --git a/drivers/media/video/cx88/cx88-alsa.c b/drivers/media/video/cx88/cx88-alsa.c index f9d87b86492..320b3d9384b 100644 --- a/drivers/media/video/cx88/cx88-alsa.c +++ b/drivers/media/video/cx88/cx88-alsa.c @@ -616,7 +616,7 @@ static struct snd_kcontrol_new snd_cx88_capture_volume = { * Only boards with eeprom and byte 1 at eeprom=1 have it */ -static struct pci_device_id cx88_audio_pci_tbl[] = { +static struct pci_device_id cx88_audio_pci_tbl[] __devinitdata = { {0x14f1,0x8801,PCI_ANY_ID,PCI_ANY_ID,0,0,0}, {0x14f1,0x8811,PCI_ANY_ID,PCI_ANY_ID,0,0,0}, {0, } diff --git a/drivers/message/fusion/mptbase.c b/drivers/message/fusion/mptbase.c index 266414ca281..9080853fe28 100644 --- a/drivers/message/fusion/mptbase.c +++ b/drivers/message/fusion/mptbase.c @@ -1189,7 +1189,6 @@ mpt_attach(struct pci_dev *pdev, const struct pci_device_id *id) ioc->diagPending = 0; spin_lock_init(&ioc->diagLock); spin_lock_init(&ioc->fc_rescan_work_lock); - spin_lock_init(&ioc->fc_rport_lock); spin_lock_init(&ioc->initializing_hba_lock); /* Initialize the event logging. @@ -5736,11 +5735,13 @@ mpt_HardResetHandler(MPT_ADAPTER *ioc, int sleepFlag) return rc; } +# define EVENT_DESCR_STR_SZ 100 + /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/ static void EventDescriptionStr(u8 event, u32 evData0, char *evStr) { - char *ds; + char *ds = NULL; switch(event) { case MPI_EVENT_NONE: @@ -5777,9 +5778,9 @@ EventDescriptionStr(u8 event, u32 evData0, char *evStr) if (evData0 == MPI_EVENT_LOOP_STATE_CHANGE_LIP) ds = "Loop State(LIP) Change"; else if (evData0 == MPI_EVENT_LOOP_STATE_CHANGE_LPE) - ds = "Loop State(LPE) Change"; /* ??? */ + ds = "Loop State(LPE) Change"; /* ??? */ else - ds = "Loop State(LPB) Change"; /* ??? */ + ds = "Loop State(LPB) Change"; /* ??? */ break; case MPI_EVENT_LOGOUT: ds = "Logout"; @@ -5841,27 +5842,32 @@ EventDescriptionStr(u8 event, u32 evData0, char *evStr) break; case MPI_EVENT_SAS_DEVICE_STATUS_CHANGE: { - char buf[50]; u8 id = (u8)(evData0); u8 ReasonCode = (u8)(evData0 >> 16); switch (ReasonCode) { case MPI_EVENT_SAS_DEV_STAT_RC_ADDED: - sprintf(buf,"SAS Device Status Change: Added: id=%d", id); + snprintf(evStr, EVENT_DESCR_STR_SZ, + "SAS Device Status Change: Added: id=%d", id); break; case MPI_EVENT_SAS_DEV_STAT_RC_NOT_RESPONDING: - sprintf(buf,"SAS Device Status Change: Deleted: id=%d", id); + snprintf(evStr, EVENT_DESCR_STR_SZ, + "SAS Device Status Change: Deleted: id=%d", id); break; case MPI_EVENT_SAS_DEV_STAT_RC_SMART_DATA: - sprintf(buf,"SAS Device Status Change: SMART Data: id=%d", id); + snprintf(evStr, EVENT_DESCR_STR_SZ, + "SAS Device Status Change: SMART Data: id=%d", + id); break; case MPI_EVENT_SAS_DEV_STAT_RC_NO_PERSIST_ADDED: - sprintf(buf,"SAS Device Status Change: No Persistancy Added: id=%d", id); + snprintf(evStr, EVENT_DESCR_STR_SZ, + "SAS Device Status Change: No Persistancy " + "Added: id=%d", id); break; default: - sprintf(buf,"SAS Device Status Change: Unknown: id=%d", id); - break; + snprintf(evStr, EVENT_DESCR_STR_SZ, + "SAS Device Status Change: Unknown: id=%d", id); + break; } - ds = buf; break; } case MPI_EVENT_ON_BUS_TIMER_EXPIRED: @@ -5878,41 +5884,46 @@ EventDescriptionStr(u8 event, u32 evData0, char *evStr) break; case MPI_EVENT_SAS_PHY_LINK_STATUS: { - char buf[50]; u8 LinkRates = (u8)(evData0 >> 8); u8 PhyNumber = (u8)(evData0); LinkRates = (LinkRates & MPI_EVENT_SAS_PLS_LR_CURRENT_MASK) >> MPI_EVENT_SAS_PLS_LR_CURRENT_SHIFT; switch (LinkRates) { case MPI_EVENT_SAS_PLS_LR_RATE_UNKNOWN: - sprintf(buf,"SAS PHY Link Status: Phy=%d:" + snprintf(evStr, EVENT_DESCR_STR_SZ, + "SAS PHY Link Status: Phy=%d:" " Rate Unknown",PhyNumber); break; case MPI_EVENT_SAS_PLS_LR_RATE_PHY_DISABLED: - sprintf(buf,"SAS PHY Link Status: Phy=%d:" + snprintf(evStr, EVENT_DESCR_STR_SZ, + "SAS PHY Link Status: Phy=%d:" " Phy Disabled",PhyNumber); break; case MPI_EVENT_SAS_PLS_LR_RATE_FAILED_SPEED_NEGOTIATION: - sprintf(buf,"SAS PHY Link Status: Phy=%d:" + snprintf(evStr, EVENT_DESCR_STR_SZ, + "SAS PHY Link Status: Phy=%d:" " Failed Speed Nego",PhyNumber); break; case MPI_EVENT_SAS_PLS_LR_RATE_SATA_OOB_COMPLETE: - sprintf(buf,"SAS PHY Link Status: Phy=%d:" + snprintf(evStr, EVENT_DESCR_STR_SZ, + "SAS PHY Link Status: Phy=%d:" " Sata OOB Completed",PhyNumber); break; case MPI_EVENT_SAS_PLS_LR_RATE_1_5: - sprintf(buf,"SAS PHY Link Status: Phy=%d:" + snprintf(evStr, EVENT_DESCR_STR_SZ, + "SAS PHY Link Status: Phy=%d:" " Rate 1.5 Gbps",PhyNumber); break; case MPI_EVENT_SAS_PLS_LR_RATE_3_0: - sprintf(buf,"SAS PHY Link Status: Phy=%d:" + snprintf(evStr, EVENT_DESCR_STR_SZ, + "SAS PHY Link Status: Phy=%d:" " Rate 3.0 Gpbs",PhyNumber); break; default: - sprintf(buf,"SAS PHY Link Status: Phy=%d", PhyNumber); + snprintf(evStr, EVENT_DESCR_STR_SZ, + "SAS PHY Link Status: Phy=%d", PhyNumber); break; } - ds = buf; break; } case MPI_EVENT_SAS_DISCOVERY_ERROR: @@ -5921,9 +5932,8 @@ EventDescriptionStr(u8 event, u32 evData0, char *evStr) case MPI_EVENT_IR_RESYNC_UPDATE: { u8 resync_complete = (u8)(evData0 >> 16); - char buf[40]; - sprintf(buf,"IR Resync Update: Complete = %d:",resync_complete); - ds = buf; + snprintf(evStr, EVENT_DESCR_STR_SZ, + "IR Resync Update: Complete = %d:",resync_complete); break; } case MPI_EVENT_IR2: @@ -5976,7 +5986,8 @@ EventDescriptionStr(u8 event, u32 evData0, char *evStr) ds = "Unknown"; break; } - strcpy(evStr,ds); + if (ds) + strncpy(evStr, ds, EVENT_DESCR_STR_SZ); } /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/ @@ -5998,7 +6009,7 @@ ProcessEventNotification(MPT_ADAPTER *ioc, EventNotificationReply_t *pEventReply int ii; int r = 0; int handlers = 0; - char evStr[100]; + char evStr[EVENT_DESCR_STR_SZ]; u8 event; /* diff --git a/drivers/message/fusion/mptbase.h b/drivers/message/fusion/mptbase.h index be7e8501b53..f673cca507e 100644 --- a/drivers/message/fusion/mptbase.h +++ b/drivers/message/fusion/mptbase.h @@ -76,8 +76,8 @@ #define COPYRIGHT "Copyright (c) 1999-2005 " MODULEAUTHOR #endif -#define MPT_LINUX_VERSION_COMMON "3.03.08" -#define MPT_LINUX_PACKAGE_NAME "@(#)mptlinux-3.03.08" +#define MPT_LINUX_VERSION_COMMON "3.03.09" +#define MPT_LINUX_PACKAGE_NAME "@(#)mptlinux-3.03.09" #define WHAT_MAGIC_STRING "@" "(" "#" ")" #define show_mptmod_ver(s,ver) \ @@ -489,7 +489,6 @@ typedef struct _RaidCfgData { #define MPT_RPORT_INFO_FLAGS_REGISTERED 0x01 /* rport registered */ #define MPT_RPORT_INFO_FLAGS_MISSING 0x02 /* missing from DevPage0 scan */ -#define MPT_RPORT_INFO_FLAGS_MAPPED_VDEV 0x04 /* target mapped in vdev */ /* * data allocated for each fc rport device @@ -501,7 +500,6 @@ struct mptfc_rport_info struct scsi_target *starget; FCDevicePage0_t pg0; u8 flags; - u8 remap_needed; }; /* @@ -628,11 +626,11 @@ typedef struct _MPT_ADAPTER struct work_struct mptscsih_persistTask; struct list_head fc_rports; - spinlock_t fc_rport_lock; /* list and ri flags */ spinlock_t fc_rescan_work_lock; int fc_rescan_work_count; struct work_struct fc_rescan_work; - + char fc_rescan_work_q_name[KOBJ_NAME_LEN]; + struct workqueue_struct *fc_rescan_work_q; } MPT_ADAPTER; /* diff --git a/drivers/message/fusion/mptfc.c b/drivers/message/fusion/mptfc.c index b343f2a68b1..856487741ef 100644 --- a/drivers/message/fusion/mptfc.c +++ b/drivers/message/fusion/mptfc.c @@ -341,9 +341,6 @@ mptfc_generate_rport_ids(FCDevicePage0_t *pg0, struct fc_rport_identifiers *rid) rid->port_name = ((u64)pg0->WWPN.High) << 32 | (u64)pg0->WWPN.Low; rid->port_id = pg0->PortIdentifier; rid->roles = FC_RPORT_ROLE_UNKNOWN; - rid->roles |= FC_RPORT_ROLE_FCP_TARGET; - if (pg0->Protocol & MPI_FC_DEVICE_PAGE0_PROT_FCP_INITIATOR) - rid->roles |= FC_RPORT_ROLE_FCP_INITIATOR; return 0; } @@ -355,15 +352,18 @@ mptfc_register_dev(MPT_ADAPTER *ioc, int channel, FCDevicePage0_t *pg0) struct fc_rport *rport; struct mptfc_rport_info *ri; int new_ri = 1; - u64 pn; - unsigned long flags; + u64 pn, nn; VirtTarget *vtarget; + u32 roles = FC_RPORT_ROLE_UNKNOWN; if (mptfc_generate_rport_ids(pg0, &rport_ids) < 0) return; + roles |= FC_RPORT_ROLE_FCP_TARGET; + if (pg0->Protocol & MPI_FC_DEVICE_PAGE0_PROT_FCP_INITIATOR) + roles |= FC_RPORT_ROLE_FCP_INITIATOR; + /* scan list looking for a match */ - spin_lock_irqsave(&ioc->fc_rport_lock, flags); list_for_each_entry(ri, &ioc->fc_rports, list) { pn = (u64)ri->pg0.WWPN.High << 32 | (u64)ri->pg0.WWPN.Low; if (pn == rport_ids.port_name) { /* match */ @@ -373,11 +373,9 @@ mptfc_register_dev(MPT_ADAPTER *ioc, int channel, FCDevicePage0_t *pg0) } } if (new_ri) { /* allocate one */ - spin_unlock_irqrestore(&ioc->fc_rport_lock, flags); ri = kzalloc(sizeof(struct mptfc_rport_info), GFP_KERNEL); if (!ri) return; - spin_lock_irqsave(&ioc->fc_rport_lock, flags); list_add_tail(&ri->list, &ioc->fc_rports); } @@ -387,14 +385,11 @@ mptfc_register_dev(MPT_ADAPTER *ioc, int channel, FCDevicePage0_t *pg0) /* MPT_RPORT_INFO_FLAGS_REGISTERED - rport not previously deleted */ if (!(ri->flags & MPT_RPORT_INFO_FLAGS_REGISTERED)) { ri->flags |= MPT_RPORT_INFO_FLAGS_REGISTERED; - spin_unlock_irqrestore(&ioc->fc_rport_lock, flags); rport = fc_remote_port_add(ioc->sh, channel, &rport_ids); - spin_lock_irqsave(&ioc->fc_rport_lock, flags); if (rport) { ri->rport = rport; if (new_ri) /* may have been reset by user */ rport->dev_loss_tmo = mptfc_dev_loss_tmo; - *((struct mptfc_rport_info **)rport->dd_data) = ri; /* * if already mapped, remap here. If not mapped, * target_alloc will allocate vtarget and map, @@ -406,16 +401,21 @@ mptfc_register_dev(MPT_ADAPTER *ioc, int channel, FCDevicePage0_t *pg0) vtarget->target_id = pg0->CurrentTargetID; vtarget->bus_id = pg0->CurrentBus; } - ri->remap_needed = 0; } + *((struct mptfc_rport_info **)rport->dd_data) = ri; + /* scan will be scheduled once rport becomes a target */ + fc_remote_port_rolechg(rport,roles); + + pn = (u64)ri->pg0.WWPN.High << 32 | (u64)ri->pg0.WWPN.Low; + nn = (u64)ri->pg0.WWNN.High << 32 | (u64)ri->pg0.WWNN.Low; dfcprintk ((MYIOC_s_INFO_FMT "mptfc_reg_dev.%d: %x, %llx / %llx, tid %d, " "rport tid %d, tmo %d\n", ioc->name, ioc->sh->host_no, pg0->PortIdentifier, - pg0->WWNN, - pg0->WWPN, + (unsigned long long)nn, + (unsigned long long)pn, pg0->CurrentTargetID, ri->rport->scsi_target_id, ri->rport->dev_loss_tmo)); @@ -425,8 +425,6 @@ mptfc_register_dev(MPT_ADAPTER *ioc, int channel, FCDevicePage0_t *pg0) ri = NULL; } } - spin_unlock_irqrestore(&ioc->fc_rport_lock,flags); - } /* @@ -476,7 +474,6 @@ mptfc_target_alloc(struct scsi_target *starget) vtarget->target_id = ri->pg0.CurrentTargetID; vtarget->bus_id = ri->pg0.CurrentBus; ri->starget = starget; - ri->remap_needed = 0; rc = 0; } } @@ -502,10 +499,10 @@ mptfc_slave_alloc(struct scsi_device *sdev) VirtDevice *vdev; struct scsi_target *starget; struct fc_rport *rport; - unsigned long flags; - rport = starget_to_rport(scsi_target(sdev)); + starget = scsi_target(sdev); + rport = starget_to_rport(starget); if (!rport || fc_remote_port_chkready(rport)) return -ENXIO; @@ -519,10 +516,8 @@ mptfc_slave_alloc(struct scsi_device *sdev) return -ENOMEM; } - spin_lock_irqsave(&hd->ioc->fc_rport_lock,flags); sdev->hostdata = vdev; - starget = scsi_target(sdev); vtarget = starget->hostdata; if (vtarget->num_luns == 0) { @@ -535,14 +530,16 @@ mptfc_slave_alloc(struct scsi_device *sdev) vdev->vtarget = vtarget; vdev->lun = sdev->lun; - spin_unlock_irqrestore(&hd->ioc->fc_rport_lock,flags); - vtarget->num_luns++; + #ifdef DMPT_DEBUG_FC - { + { + u64 nn, pn; struct mptfc_rport_info *ri; ri = *((struct mptfc_rport_info **)rport->dd_data); + pn = (u64)ri->pg0.WWPN.High << 32 | (u64)ri->pg0.WWPN.Low; + nn = (u64)ri->pg0.WWNN.High << 32 | (u64)ri->pg0.WWNN.Low; dfcprintk ((MYIOC_s_INFO_FMT "mptfc_slv_alloc.%d: num_luns %d, sdev.id %d, " "CurrentTargetID %d, %x %llx %llx\n", @@ -550,7 +547,9 @@ mptfc_slave_alloc(struct scsi_device *sdev) sdev->host->host_no, vtarget->num_luns, sdev->id, ri->pg0.CurrentTargetID, - ri->pg0.PortIdentifier, ri->pg0.WWPN, ri->pg0.WWNN)); + ri->pg0.PortIdentifier, + (unsigned long long)pn, + (unsigned long long)nn)); } #endif @@ -570,11 +569,31 @@ mptfc_qcmd(struct scsi_cmnd *SCpnt, void (*done)(struct scsi_cmnd *)) done(SCpnt); return 0; } + + /* dd_data is null until finished adding target */ ri = *((struct mptfc_rport_info **)rport->dd_data); - if (unlikely(ri->remap_needed)) - return SCSI_MLQUEUE_HOST_BUSY; + if (unlikely(!ri)) { + dfcprintk ((MYIOC_s_INFO_FMT + "mptfc_qcmd.%d: %d:%d, dd_data is null.\n", + ((MPT_SCSI_HOST *) SCpnt->device->host->hostdata)->ioc->name, + ((MPT_SCSI_HOST *) SCpnt->device->host->hostdata)->ioc->sh->host_no, + SCpnt->device->id,SCpnt->device->lun)); + SCpnt->result = DID_IMM_RETRY << 16; + done(SCpnt); + return 0; + } - return mptscsih_qcmd(SCpnt,done); + err = mptscsih_qcmd(SCpnt,done); +#ifdef DMPT_DEBUG_FC + if (unlikely(err)) { + dfcprintk ((MYIOC_s_INFO_FMT + "mptfc_qcmd.%d: %d:%d, mptscsih_qcmd returns non-zero.\n", + ((MPT_SCSI_HOST *) SCpnt->device->host->hostdata)->ioc->name, + ((MPT_SCSI_HOST *) SCpnt->device->host->hostdata)->ioc->sh->host_no, + SCpnt->device->id,SCpnt->device->lun)); + } +#endif + return err; } static void @@ -615,18 +634,17 @@ mptfc_rescan_devices(void *arg) MPT_ADAPTER *ioc = (MPT_ADAPTER *)arg; int ii; int work_to_do; + u64 pn; unsigned long flags; struct mptfc_rport_info *ri; do { /* start by tagging all ports as missing */ - spin_lock_irqsave(&ioc->fc_rport_lock,flags); list_for_each_entry(ri, &ioc->fc_rports, list) { if (ri->flags & MPT_RPORT_INFO_FLAGS_REGISTERED) { ri->flags |= MPT_RPORT_INFO_FLAGS_MISSING; } } - spin_unlock_irqrestore(&ioc->fc_rport_lock,flags); /* * now rescan devices known to adapter, @@ -639,33 +657,24 @@ mptfc_rescan_devices(void *arg) } /* delete devices still missing */ - spin_lock_irqsave(&ioc->fc_rport_lock, flags); list_for_each_entry(ri, &ioc->fc_rports, list) { /* if newly missing, delete it */ - if ((ri->flags & (MPT_RPORT_INFO_FLAGS_REGISTERED | - MPT_RPORT_INFO_FLAGS_MISSING)) - == (MPT_RPORT_INFO_FLAGS_REGISTERED | - MPT_RPORT_INFO_FLAGS_MISSING)) { + if (ri->flags & MPT_RPORT_INFO_FLAGS_MISSING) { ri->flags &= ~(MPT_RPORT_INFO_FLAGS_REGISTERED| MPT_RPORT_INFO_FLAGS_MISSING); - ri->remap_needed = 1; - fc_remote_port_delete(ri->rport); - /* - * remote port not really deleted 'cause - * binding is by WWPN and driver only - * registers FCP_TARGETs but cannot trust - * data structures. - */ + fc_remote_port_delete(ri->rport); /* won't sleep */ ri->rport = NULL; + + pn = (u64)ri->pg0.WWPN.High << 32 | + (u64)ri->pg0.WWPN.Low; dfcprintk ((MYIOC_s_INFO_FMT "mptfc_rescan.%d: %llx deleted\n", ioc->name, ioc->sh->host_no, - ri->pg0.WWPN)); + (unsigned long long)pn)); } } - spin_unlock_irqrestore(&ioc->fc_rport_lock,flags); /* * allow multiple passes as target state @@ -870,10 +879,23 @@ mptfc_probe(struct pci_dev *pdev, const struct pci_device_id *id) goto out_mptfc_probe; } - for (ii=0; ii < ioc->facts.NumberOfPorts; ii++) { - mptfc_init_host_attr(ioc,ii); - mptfc_GetFcDevPage0(ioc,ii,mptfc_register_dev); - } + /* initialize workqueue */ + + snprintf(ioc->fc_rescan_work_q_name, KOBJ_NAME_LEN, "mptfc_wq_%d", + sh->host_no); + ioc->fc_rescan_work_q = + create_singlethread_workqueue(ioc->fc_rescan_work_q_name); + if (!ioc->fc_rescan_work_q) + goto out_mptfc_probe; + + /* + * scan for rports - + * by doing it via the workqueue, some locking is eliminated + */ + + ioc->fc_rescan_work_count = 1; + queue_work(ioc->fc_rescan_work_q, &ioc->fc_rescan_work); + flush_workqueue(ioc->fc_rescan_work_q); return 0; @@ -949,8 +971,18 @@ mptfc_init(void) static void __devexit mptfc_remove(struct pci_dev *pdev) { - MPT_ADAPTER *ioc = pci_get_drvdata(pdev); - struct mptfc_rport_info *p, *n; + MPT_ADAPTER *ioc = pci_get_drvdata(pdev); + struct mptfc_rport_info *p, *n; + struct workqueue_struct *work_q; + unsigned long flags; + + /* destroy workqueue */ + if ((work_q=ioc->fc_rescan_work_q)) { + spin_lock_irqsave(&ioc->fc_rescan_work_lock, flags); + ioc->fc_rescan_work_q = NULL; + spin_unlock_irqrestore(&ioc->fc_rescan_work_lock, flags); + destroy_workqueue(work_q); + } fc_remove_host(ioc->sh); diff --git a/drivers/message/fusion/mptsas.c b/drivers/message/fusion/mptsas.c index e9716b10ace..af6ec553ff7 100644 --- a/drivers/message/fusion/mptsas.c +++ b/drivers/message/fusion/mptsas.c @@ -91,6 +91,7 @@ enum mptsas_hotplug_action { MPTSAS_DEL_DEVICE, MPTSAS_ADD_RAID, MPTSAS_DEL_RAID, + MPTSAS_IGNORE_EVENT, }; struct mptsas_hotplug_event { @@ -298,6 +299,26 @@ mptsas_find_portinfo_by_handle(MPT_ADAPTER *ioc, u16 handle) return rc; } +/* + * Returns true if there is a scsi end device + */ +static inline int +mptsas_is_end_device(struct mptsas_devinfo * attached) +{ + if ((attached->handle) && + (attached->device_info & + MPI_SAS_DEVICE_INFO_END_DEVICE) && + ((attached->device_info & + MPI_SAS_DEVICE_INFO_SSP_TARGET) | + (attached->device_info & + MPI_SAS_DEVICE_INFO_STP_TARGET) | + (attached->device_info & + MPI_SAS_DEVICE_INFO_SATA_DEVICE))) + return 1; + else + return 0; +} + static int mptsas_sas_enclosure_pg0(MPT_ADAPTER *ioc, struct mptsas_enclosure *enclosure, u32 form, u32 form_specific) @@ -872,7 +893,11 @@ mptsas_sas_device_pg0(MPT_ADAPTER *ioc, struct mptsas_devinfo *device_info, SasDevicePage0_t *buffer; dma_addr_t dma_handle; __le64 sas_address; - int error; + int error=0; + + if (ioc->sas_discovery_runtime && + mptsas_is_end_device(device_info)) + goto out; hdr.PageVersion = MPI_SASDEVICE0_PAGEVERSION; hdr.ExtPageLength = 0; @@ -1009,7 +1034,11 @@ mptsas_sas_expander_pg1(MPT_ADAPTER *ioc, struct mptsas_phyinfo *phy_info, CONFIGPARMS cfg; SasExpanderPage1_t *buffer; dma_addr_t dma_handle; - int error; + int error=0; + + if (ioc->sas_discovery_runtime && + mptsas_is_end_device(&phy_info->attached)) + goto out; hdr.PageVersion = MPI_SASEXPANDER0_PAGEVERSION; hdr.ExtPageLength = 0; @@ -1068,26 +1097,6 @@ mptsas_sas_expander_pg1(MPT_ADAPTER *ioc, struct mptsas_phyinfo *phy_info, return error; } -/* - * Returns true if there is a scsi end device - */ -static inline int -mptsas_is_end_device(struct mptsas_devinfo * attached) -{ - if ((attached->handle) && - (attached->device_info & - MPI_SAS_DEVICE_INFO_END_DEVICE) && - ((attached->device_info & - MPI_SAS_DEVICE_INFO_SSP_TARGET) | - (attached->device_info & - MPI_SAS_DEVICE_INFO_STP_TARGET) | - (attached->device_info & - MPI_SAS_DEVICE_INFO_SATA_DEVICE))) - return 1; - else - return 0; -} - static void mptsas_parse_device_info(struct sas_identify *identify, struct mptsas_devinfo *device_info) @@ -1737,6 +1746,9 @@ mptsas_hotplug_work(void *arg) break; case MPTSAS_ADD_DEVICE: + if (ev->phys_disk_num_valid) + mpt_findImVolumes(ioc); + /* * Refresh sas device pg0 data */ @@ -1868,6 +1880,9 @@ mptsas_hotplug_work(void *arg) scsi_device_put(sdev); mpt_findImVolumes(ioc); break; + case MPTSAS_IGNORE_EVENT: + default: + break; } kfree(ev); @@ -1940,7 +1955,8 @@ mptscsih_send_raid_event(MPT_ADAPTER *ioc, EVENT_DATA_RAID *raid_event_data) { struct mptsas_hotplug_event *ev; - RAID_VOL0_STATUS * volumeStatus; + int status = le32_to_cpu(raid_event_data->SettingsStatus); + int state = (status >> 8) & 0xff; if (ioc->bus_type != SAS) return; @@ -1955,6 +1971,7 @@ mptscsih_send_raid_event(MPT_ADAPTER *ioc, INIT_WORK(&ev->work, mptsas_hotplug_work, ev); ev->ioc = ioc; ev->id = raid_event_data->VolumeID; + ev->event_type = MPTSAS_IGNORE_EVENT; switch (raid_event_data->ReasonCode) { case MPI_EVENT_RAID_RC_PHYSDISK_DELETED: @@ -1966,6 +1983,25 @@ mptscsih_send_raid_event(MPT_ADAPTER *ioc, ev->phys_disk_num = raid_event_data->PhysDiskNum; ev->event_type = MPTSAS_DEL_DEVICE; break; + case MPI_EVENT_RAID_RC_PHYSDISK_STATUS_CHANGED: + switch (state) { + case MPI_PD_STATE_ONLINE: + ioc->raid_data.isRaid = 1; + ev->phys_disk_num_valid = 1; + ev->phys_disk_num = raid_event_data->PhysDiskNum; + ev->event_type = MPTSAS_ADD_DEVICE; + break; + case MPI_PD_STATE_MISSING: + case MPI_PD_STATE_NOT_COMPATIBLE: + case MPI_PD_STATE_OFFLINE_AT_HOST_REQUEST: + case MPI_PD_STATE_FAILED_AT_HOST_REQUEST: + case MPI_PD_STATE_OFFLINE_FOR_ANOTHER_REASON: + ev->event_type = MPTSAS_DEL_DEVICE; + break; + default: + break; + } + break; case MPI_EVENT_RAID_RC_VOLUME_DELETED: ev->event_type = MPTSAS_DEL_RAID; break; @@ -1973,11 +2009,18 @@ mptscsih_send_raid_event(MPT_ADAPTER *ioc, ev->event_type = MPTSAS_ADD_RAID; break; case MPI_EVENT_RAID_RC_VOLUME_STATUS_CHANGED: - volumeStatus = (RAID_VOL0_STATUS *) & - raid_event_data->SettingsStatus; - ev->event_type = (volumeStatus->State == - MPI_RAIDVOL0_STATUS_STATE_FAILED) ? - MPTSAS_DEL_RAID : MPTSAS_ADD_RAID; + switch (state) { + case MPI_RAIDVOL0_STATUS_STATE_FAILED: + case MPI_RAIDVOL0_STATUS_STATE_MISSING: + ev->event_type = MPTSAS_DEL_RAID; + break; + case MPI_RAIDVOL0_STATUS_STATE_OPTIMAL: + case MPI_RAIDVOL0_STATUS_STATE_DEGRADED: + ev->event_type = MPTSAS_ADD_RAID; + break; + default: + break; + } break; default: break; diff --git a/drivers/message/fusion/mptscsih.c b/drivers/message/fusion/mptscsih.c index 3729062db31..84fa271eb8f 100644 --- a/drivers/message/fusion/mptscsih.c +++ b/drivers/message/fusion/mptscsih.c @@ -632,7 +632,11 @@ mptscsih_io_done(MPT_ADAPTER *ioc, MPT_FRAME_HDR *mf, MPT_FRAME_HDR *mr) case MPI_IOCSTATUS_SCSI_DEVICE_NOT_THERE: /* 0x0043 */ /* Spoof to SCSI Selection Timeout! */ - sc->result = DID_NO_CONNECT << 16; + if (ioc->bus_type != FC) + sc->result = DID_NO_CONNECT << 16; + /* else fibre, just stall until rescan event */ + else + sc->result = DID_REQUEUE << 16; if (hd->sel_timeout[pScsiReq->TargetID] < 0xFFFF) hd->sel_timeout[pScsiReq->TargetID]++; @@ -877,7 +881,7 @@ mptscsih_search_running_cmds(MPT_SCSI_HOST *hd, VirtDevice *vdevice) struct scsi_cmnd *sc; dsprintk((KERN_INFO MYNAM ": search_running target %d lun %d max %d\n", - vdevice->target_id, vdevice->lun, max)); + vdevice->vtarget->target_id, vdevice->lun, max)); for (ii=0; ii < max; ii++) { if ((sc = hd->ScsiLookup[ii]) != NULL) { @@ -1645,7 +1649,6 @@ int mptscsih_abort(struct scsi_cmnd * SCpnt) { MPT_SCSI_HOST *hd; - MPT_ADAPTER *ioc; MPT_FRAME_HDR *mf; u32 ctx2abort; int scpnt_idx; @@ -1663,14 +1666,6 @@ mptscsih_abort(struct scsi_cmnd * SCpnt) return FAILED; } - ioc = hd->ioc; - if (hd->resetPending) { - return FAILED; - } - - if (hd->timeouts < -1) - hd->timeouts++; - /* Find this command */ if ((scpnt_idx = SCPNT_TO_LOOKUP_IDX(SCpnt)) < 0) { @@ -1684,6 +1679,13 @@ mptscsih_abort(struct scsi_cmnd * SCpnt) return SUCCESS; } + if (hd->resetPending) { + return FAILED; + } + + if (hd->timeouts < -1) + hd->timeouts++; + printk(KERN_WARNING MYNAM ": %s: attempting task abort! (sc=%p)\n", hd->ioc->name, SCpnt); scsi_print_command(SCpnt); @@ -1703,7 +1705,7 @@ mptscsih_abort(struct scsi_cmnd * SCpnt) vdev = SCpnt->device->hostdata; retval = mptscsih_TMHandler(hd, MPI_SCSITASKMGMT_TASKTYPE_ABORT_TASK, vdev->vtarget->bus_id, vdev->vtarget->target_id, vdev->lun, - ctx2abort, mptscsih_get_tm_timeout(ioc)); + ctx2abort, mptscsih_get_tm_timeout(hd->ioc)); printk (KERN_WARNING MYNAM ": %s: task abort: %s (sc=%p)\n", hd->ioc->name, @@ -2521,15 +2523,15 @@ mptscsih_ioc_reset(MPT_ADAPTER *ioc, int reset_phase) /* 7. FC: Rescan for blocked rports which might have returned. */ - else if (ioc->bus_type == FC) { - int work_count; - unsigned long flags; - + if (ioc->bus_type == FC) { spin_lock_irqsave(&ioc->fc_rescan_work_lock, flags); - work_count = ++ioc->fc_rescan_work_count; + if (ioc->fc_rescan_work_q) { + if (ioc->fc_rescan_work_count++ == 0) { + queue_work(ioc->fc_rescan_work_q, + &ioc->fc_rescan_work); + } + } spin_unlock_irqrestore(&ioc->fc_rescan_work_lock, flags); - if (work_count == 1) - schedule_work(&ioc->fc_rescan_work); } dtmprintk((MYIOC_s_WARN_FMT "Post-Reset complete.\n", ioc->name)); @@ -2544,7 +2546,6 @@ mptscsih_event_process(MPT_ADAPTER *ioc, EventNotificationReply_t *pEvReply) { MPT_SCSI_HOST *hd; u8 event = le32_to_cpu(pEvReply->Event) & 0xFF; - int work_count; unsigned long flags; devtverboseprintk((MYIOC_s_INFO_FMT "MPT event (=%02Xh) routed to SCSI host driver!\n", @@ -2569,10 +2570,13 @@ mptscsih_event_process(MPT_ADAPTER *ioc, EventNotificationReply_t *pEvReply) case MPI_EVENT_RESCAN: /* 06 */ spin_lock_irqsave(&ioc->fc_rescan_work_lock, flags); - work_count = ++ioc->fc_rescan_work_count; + if (ioc->fc_rescan_work_q) { + if (ioc->fc_rescan_work_count++ == 0) { + queue_work(ioc->fc_rescan_work_q, + &ioc->fc_rescan_work); + } + } spin_unlock_irqrestore(&ioc->fc_rescan_work_lock, flags); - if (work_count == 1) - schedule_work(&ioc->fc_rescan_work); break; /* diff --git a/drivers/message/fusion/mptspi.c b/drivers/message/fusion/mptspi.c index 09c745b19cc..f2a4d382ea1 100644 --- a/drivers/message/fusion/mptspi.c +++ b/drivers/message/fusion/mptspi.c @@ -783,6 +783,70 @@ static struct pci_device_id mptspi_pci_table[] = { }; MODULE_DEVICE_TABLE(pci, mptspi_pci_table); + +/* + * renegotiate for a given target + */ +static void +mptspi_dv_renegotiate_work(void *data) +{ + struct work_queue_wrapper *wqw = (struct work_queue_wrapper *)data; + struct _MPT_SCSI_HOST *hd = wqw->hd; + struct scsi_device *sdev; + + kfree(wqw); + + shost_for_each_device(sdev, hd->ioc->sh) + mptspi_dv_device(hd, sdev); +} + +static void +mptspi_dv_renegotiate(struct _MPT_SCSI_HOST *hd) +{ + struct work_queue_wrapper *wqw = kmalloc(sizeof(*wqw), GFP_ATOMIC); + + if (!wqw) + return; + + INIT_WORK(&wqw->work, mptspi_dv_renegotiate_work, wqw); + wqw->hd = hd; + + schedule_work(&wqw->work); +} + +/* + * spi module reset handler + */ +static int +mptspi_ioc_reset(MPT_ADAPTER *ioc, int reset_phase) +{ + struct _MPT_SCSI_HOST *hd = (struct _MPT_SCSI_HOST *)ioc->sh->hostdata; + int rc; + + rc = mptscsih_ioc_reset(ioc, reset_phase); + + if (reset_phase == MPT_IOC_POST_RESET) + mptspi_dv_renegotiate(hd); + + return rc; +} + +/* + * spi module resume handler + */ +static int +mptspi_resume(struct pci_dev *pdev) +{ + MPT_ADAPTER *ioc = pci_get_drvdata(pdev); + struct _MPT_SCSI_HOST *hd = (struct _MPT_SCSI_HOST *)ioc->sh->hostdata; + int rc; + + rc = mptscsih_resume(pdev); + mptspi_dv_renegotiate(hd); + + return rc; +} + /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/ /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/ /* @@ -1032,7 +1096,7 @@ static struct pci_driver mptspi_driver = { .shutdown = mptscsih_shutdown, #ifdef CONFIG_PM .suspend = mptscsih_suspend, - .resume = mptscsih_resume, + .resume = mptspi_resume, #endif }; @@ -1061,7 +1125,7 @@ mptspi_init(void) ": Registered for IOC event notifications\n")); } - if (mpt_reset_register(mptspiDoneCtx, mptscsih_ioc_reset) == 0) { + if (mpt_reset_register(mptspiDoneCtx, mptspi_ioc_reset) == 0) { dprintk((KERN_INFO MYNAM ": Registered for IOC reset notifications\n")); } diff --git a/drivers/mmc/at91_mci.c b/drivers/mmc/at91_mci.c index 6061c2d101a..88f0eef9cf3 100644 --- a/drivers/mmc/at91_mci.c +++ b/drivers/mmc/at91_mci.c @@ -621,9 +621,6 @@ static void at91_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) struct at91mci_host *host = mmc_priv(mmc); unsigned long at91_master_clock = clk_get_rate(mci_clk); - DBG("Clock %uHz, busmode %u, powermode %u, Vdd %u\n", - ios->clock, ios->bus_mode, ios->power_mode, ios->vdd); - if (host) host->bus_mode = ios->bus_mode; else diff --git a/drivers/mmc/au1xmmc.c b/drivers/mmc/au1xmmc.c index c0326bbc5f2..914d62b2406 100644 --- a/drivers/mmc/au1xmmc.c +++ b/drivers/mmc/au1xmmc.c @@ -720,10 +720,6 @@ static void au1xmmc_set_ios(struct mmc_host* mmc, struct mmc_ios* ios) { struct au1xmmc_host *host = mmc_priv(mmc); - DBG("set_ios (power=%u, clock=%uHz, vdd=%u, mode=%u)\n", - host->id, ios->power_mode, ios->clock, ios->vdd, - ios->bus_mode); - if (ios->power_mode == MMC_POWER_OFF) au1xmmc_set_power(host, 0); else if (ios->power_mode == MMC_POWER_ON) { diff --git a/drivers/mmc/imxmmc.c b/drivers/mmc/imxmmc.c index ffb7f55d346..79358e223f5 100644 --- a/drivers/mmc/imxmmc.c +++ b/drivers/mmc/imxmmc.c @@ -102,6 +102,7 @@ struct imxmci_host { #define IMXMCI_PEND_CPU_DATA_b 5 #define IMXMCI_PEND_CARD_XCHG_b 6 #define IMXMCI_PEND_SET_INIT_b 7 +#define IMXMCI_PEND_STARTED_b 8 #define IMXMCI_PEND_IRQ_m (1 << IMXMCI_PEND_IRQ_b) #define IMXMCI_PEND_DMA_END_m (1 << IMXMCI_PEND_DMA_END_b) @@ -111,6 +112,7 @@ struct imxmci_host { #define IMXMCI_PEND_CPU_DATA_m (1 << IMXMCI_PEND_CPU_DATA_b) #define IMXMCI_PEND_CARD_XCHG_m (1 << IMXMCI_PEND_CARD_XCHG_b) #define IMXMCI_PEND_SET_INIT_m (1 << IMXMCI_PEND_SET_INIT_b) +#define IMXMCI_PEND_STARTED_m (1 << IMXMCI_PEND_STARTED_b) static void imxmci_stop_clock(struct imxmci_host *host) { @@ -131,23 +133,52 @@ static void imxmci_stop_clock(struct imxmci_host *host) dev_dbg(mmc_dev(host->mmc), "imxmci_stop_clock blocked, no luck\n"); } -static void imxmci_start_clock(struct imxmci_host *host) +static int imxmci_start_clock(struct imxmci_host *host) { - int i = 0; + unsigned int trials = 0; + unsigned int delay_limit = 128; + unsigned long flags; + MMC_STR_STP_CLK &= ~STR_STP_CLK_STOP_CLK; - while(i < 0x1000) { - if(!(i & 0x7f)) - MMC_STR_STP_CLK |= STR_STP_CLK_START_CLK; - if(MMC_STATUS & STATUS_CARD_BUS_CLK_RUN) { - /* Check twice before cut */ + clear_bit(IMXMCI_PEND_STARTED_b, &host->pending_events); + + /* + * Command start of the clock, this usually succeeds in less + * then 6 delay loops, but during card detection (low clockrate) + * it takes up to 5000 delay loops and sometimes fails for the first time + */ + MMC_STR_STP_CLK |= STR_STP_CLK_START_CLK; + + do { + unsigned int delay = delay_limit; + + while(delay--){ if(MMC_STATUS & STATUS_CARD_BUS_CLK_RUN) - return; + /* Check twice before cut */ + if(MMC_STATUS & STATUS_CARD_BUS_CLK_RUN) + return 0; + + if(test_bit(IMXMCI_PEND_STARTED_b, &host->pending_events)) + return 0; } - i++; - } - dev_dbg(mmc_dev(host->mmc), "imxmci_start_clock blocked, no luck\n"); + local_irq_save(flags); + /* + * Ensure, that request is not doubled under all possible circumstances. + * It is possible, that cock running state is missed, because some other + * IRQ or schedule delays this function execution and the clocks has + * been already stopped by other means (response processing, SDHC HW) + */ + if(!test_bit(IMXMCI_PEND_STARTED_b, &host->pending_events)) + MMC_STR_STP_CLK |= STR_STP_CLK_START_CLK; + local_irq_restore(flags); + + } while(++trials<256); + + dev_err(mmc_dev(host->mmc), "imxmci_start_clock blocked, no luck\n"); + + return -1; } static void imxmci_softreset(void) @@ -498,7 +529,7 @@ static int imxmci_data_done(struct imxmci_host *host, unsigned int stat) data_error = imxmci_finish_data(host, stat); - if (host->req->stop && (data_error == MMC_ERR_NONE)) { + if (host->req->stop) { imxmci_stop_clock(host); imxmci_start_cmd(host, host->req->stop, 0); } else { @@ -622,6 +653,7 @@ static irqreturn_t imxmci_irq(int irq, void *devid, struct pt_regs *regs) atomic_set(&host->stuck_timeout, 0); host->status_reg = stat; set_bit(IMXMCI_PEND_IRQ_b, &host->pending_events); + set_bit(IMXMCI_PEND_STARTED_b, &host->pending_events); tasklet_schedule(&host->tasklet); return IRQ_RETVAL(handled);; @@ -775,10 +807,6 @@ static void imxmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) struct imxmci_host *host = mmc_priv(mmc); int prescaler; - dev_dbg(mmc_dev(host->mmc), "clock %u power %u vdd %u width %u\n", - ios->clock, ios->power_mode, ios->vdd, - (ios->bus_width==MMC_BUS_WIDTH_4)?4:1); - if( ios->bus_width==MMC_BUS_WIDTH_4 ) { host->actual_bus_width = MMC_BUS_WIDTH_4; imx_gpio_mode(PB11_PF_SD_DAT3); diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c index da6ddd910fc..1ca2c8b9c9b 100644 --- a/drivers/mmc/mmc.c +++ b/drivers/mmc/mmc.c @@ -59,21 +59,23 @@ static const unsigned int tacc_mant[] = { /** - * mmc_request_done - finish processing an MMC command - * @host: MMC host which completed command - * @mrq: MMC request which completed + * mmc_request_done - finish processing an MMC request + * @host: MMC host which completed request + * @mrq: MMC request which request * * MMC drivers should call this function when they have completed - * their processing of a command. This should be called before the - * data part of the command has completed. + * their processing of a request. */ void mmc_request_done(struct mmc_host *host, struct mmc_request *mrq) { struct mmc_command *cmd = mrq->cmd; - int err = mrq->cmd->error; - pr_debug("MMC: req done (%02x): %d: %08x %08x %08x %08x\n", - cmd->opcode, err, cmd->resp[0], cmd->resp[1], - cmd->resp[2], cmd->resp[3]); + int err = cmd->error; + + pr_debug("%s: req done (CMD%u): %d/%d/%d: %08x %08x %08x %08x\n", + mmc_hostname(host), cmd->opcode, err, + mrq->data ? mrq->data->error : 0, + mrq->stop ? mrq->stop->error : 0, + cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3]); if (err && cmd->retries) { cmd->retries--; @@ -97,8 +99,9 @@ EXPORT_SYMBOL(mmc_request_done); void mmc_start_request(struct mmc_host *host, struct mmc_request *mrq) { - pr_debug("MMC: starting cmd %02x arg %08x flags %08x\n", - mrq->cmd->opcode, mrq->cmd->arg, mrq->cmd->flags); + pr_debug("%s: starting CMD%u arg %08x flags %08x\n", + mmc_hostname(host), mrq->cmd->opcode, + mrq->cmd->arg, mrq->cmd->flags); WARN_ON(host->card_busy == NULL); @@ -312,6 +315,18 @@ void mmc_release_host(struct mmc_host *host) EXPORT_SYMBOL(mmc_release_host); +static inline void mmc_set_ios(struct mmc_host *host) +{ + struct mmc_ios *ios = &host->ios; + + pr_debug("%s: clock %uHz busmode %u powermode %u cs %u Vdd %u width %u\n", + mmc_hostname(host), ios->clock, ios->bus_mode, + ios->power_mode, ios->chip_select, ios->vdd, + ios->bus_width); + + host->ops->set_ios(host, ios); +} + static int mmc_select_card(struct mmc_host *host, struct mmc_card *card) { int err; @@ -364,7 +379,7 @@ static int mmc_select_card(struct mmc_host *host, struct mmc_card *card) } } - host->ops->set_ios(host, &host->ios); + mmc_set_ios(host); return MMC_ERR_NONE; } @@ -415,7 +430,7 @@ static u32 mmc_select_voltage(struct mmc_host *host, u32 ocr) ocr = 3 << bit; host->ios.vdd = bit; - host->ops->set_ios(host, &host->ios); + mmc_set_ios(host); } else { ocr = 0; } @@ -549,6 +564,7 @@ static void mmc_decode_csd(struct mmc_card *card) csd->read_partial = UNSTUFF_BITS(resp, 79, 1); csd->write_misalign = UNSTUFF_BITS(resp, 78, 1); csd->read_misalign = UNSTUFF_BITS(resp, 77, 1); + csd->r2w_factor = UNSTUFF_BITS(resp, 26, 3); csd->write_blkbits = UNSTUFF_BITS(resp, 22, 4); csd->write_partial = UNSTUFF_BITS(resp, 21, 1); } else { @@ -583,6 +599,7 @@ static void mmc_decode_csd(struct mmc_card *card) csd->read_partial = UNSTUFF_BITS(resp, 79, 1); csd->write_misalign = UNSTUFF_BITS(resp, 78, 1); csd->read_misalign = UNSTUFF_BITS(resp, 77, 1); + csd->r2w_factor = UNSTUFF_BITS(resp, 26, 3); csd->write_blkbits = UNSTUFF_BITS(resp, 22, 4); csd->write_partial = UNSTUFF_BITS(resp, 21, 1); } @@ -666,7 +683,7 @@ static void mmc_idle_cards(struct mmc_host *host) struct mmc_command cmd; host->ios.chip_select = MMC_CS_HIGH; - host->ops->set_ios(host, &host->ios); + mmc_set_ios(host); mmc_delay(1); @@ -679,7 +696,7 @@ static void mmc_idle_cards(struct mmc_host *host) mmc_delay(1); host->ios.chip_select = MMC_CS_DONTCARE; - host->ops->set_ios(host, &host->ios); + mmc_set_ios(host); mmc_delay(1); } @@ -704,13 +721,13 @@ static void mmc_power_up(struct mmc_host *host) host->ios.chip_select = MMC_CS_DONTCARE; host->ios.power_mode = MMC_POWER_UP; host->ios.bus_width = MMC_BUS_WIDTH_1; - host->ops->set_ios(host, &host->ios); + mmc_set_ios(host); mmc_delay(1); host->ios.clock = host->f_min; host->ios.power_mode = MMC_POWER_ON; - host->ops->set_ios(host, &host->ios); + mmc_set_ios(host); mmc_delay(2); } @@ -723,7 +740,7 @@ static void mmc_power_off(struct mmc_host *host) host->ios.chip_select = MMC_CS_DONTCARE; host->ios.power_mode = MMC_POWER_OFF; host->ios.bus_width = MMC_BUS_WIDTH_1; - host->ops->set_ios(host, &host->ios); + mmc_set_ios(host); } static int mmc_send_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr) @@ -971,7 +988,8 @@ static unsigned int mmc_calculate_clock(struct mmc_host *host) if (!mmc_card_dead(card) && max_dtr > card->csd.max_dtr) max_dtr = card->csd.max_dtr; - pr_debug("MMC: selected %d.%03dMHz transfer rate\n", + pr_debug("%s: selected %d.%03dMHz transfer rate\n", + mmc_hostname(host), max_dtr / 1000000, (max_dtr / 1000) % 1000); return max_dtr; @@ -1046,7 +1064,7 @@ static void mmc_setup(struct mmc_host *host) } else { host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN; host->ios.clock = host->f_min; - host->ops->set_ios(host, &host->ios); + mmc_set_ios(host); /* * We should remember the OCR mask from the existing @@ -1082,7 +1100,7 @@ static void mmc_setup(struct mmc_host *host) * Ok, now switch to push-pull mode. */ host->ios.bus_mode = MMC_BUSMODE_PUSHPULL; - host->ops->set_ios(host, &host->ios); + mmc_set_ios(host); mmc_read_csds(host); @@ -1128,7 +1146,7 @@ static void mmc_rescan(void *data) * attached cards and the host support. */ host->ios.clock = mmc_calculate_clock(host); - host->ops->set_ios(host, &host->ios); + mmc_set_ios(host); } mmc_release_host(host); diff --git a/drivers/mmc/mmc_block.c b/drivers/mmc/mmc_block.c index 8eb2a2ede64..06bd1f4cb9b 100644 --- a/drivers/mmc/mmc_block.c +++ b/drivers/mmc/mmc_block.c @@ -187,6 +187,12 @@ static int mmc_blk_issue_rq(struct mmc_queue *mq, struct request *req) brq.cmd.opcode = MMC_WRITE_BLOCK; brq.data.flags |= MMC_DATA_WRITE; brq.data.blocks = 1; + + /* + * Scale up the timeout by the r2w factor + */ + brq.data.timeout_ns <<= card->csd.r2w_factor; + brq.data.timeout_clks <<= card->csd.r2w_factor; } if (brq.data.blocks > 1) { diff --git a/drivers/mmc/mmci.c b/drivers/mmc/mmci.c index df7e861e2fc..da8e4d7339c 100644 --- a/drivers/mmc/mmci.c +++ b/drivers/mmc/mmci.c @@ -402,9 +402,6 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) struct mmci_host *host = mmc_priv(mmc); u32 clk = 0, pwr = 0; - DBG(host, "clock %uHz busmode %u powermode %u Vdd %u\n", - ios->clock, ios->bus_mode, ios->power_mode, ios->vdd); - if (ios->clock) { if (ios->clock >= host->mclk) { clk = MCI_CLK_BYPASS; diff --git a/drivers/mmc/pxamci.c b/drivers/mmc/pxamci.c index eb42cb34942..f97b472085c 100644 --- a/drivers/mmc/pxamci.c +++ b/drivers/mmc/pxamci.c @@ -198,7 +198,6 @@ static void pxamci_start_cmd(struct pxamci_host *host, struct mmc_command *cmd, static void pxamci_finish_request(struct pxamci_host *host, struct mmc_request *mrq) { - pr_debug("PXAMCI: request done\n"); host->mrq = NULL; host->cmd = NULL; host->data = NULL; @@ -291,7 +290,7 @@ static int pxamci_data_done(struct pxamci_host *host, unsigned int stat) pxamci_disable_irq(host, DATA_TRAN_DONE); host->data = NULL; - if (host->mrq->stop && data->error == MMC_ERR_NONE) { + if (host->mrq->stop) { pxamci_stop_clock(host); pxamci_start_cmd(host, host->mrq->stop, 0); } else { @@ -309,12 +308,10 @@ static irqreturn_t pxamci_irq(int irq, void *devid, struct pt_regs *regs) ireg = readl(host->base + MMC_I_REG); - pr_debug("PXAMCI: irq %08x\n", ireg); - if (ireg) { unsigned stat = readl(host->base + MMC_STAT); - pr_debug("PXAMCI: stat %08x\n", stat); + pr_debug("PXAMCI: irq %08x stat %08x\n", ireg, stat); if (ireg & END_CMD_RES) handled |= pxamci_cmd_done(host, stat); @@ -368,10 +365,6 @@ static void pxamci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) { struct pxamci_host *host = mmc_priv(mmc); - pr_debug("pxamci_set_ios: clock %u power %u vdd %u.%02u\n", - ios->clock, ios->power_mode, ios->vdd / 100, - ios->vdd % 100); - if (ios->clock) { unsigned int clk = CLOCKRATE / ios->clock; if (CLOCKRATE / clk > ios->clock) @@ -397,7 +390,7 @@ static void pxamci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) host->cmdat |= CMDAT_INIT; } - pr_debug("pxamci_set_ios: clkrt = %x cmdat = %x\n", + pr_debug("PXAMCI: clkrt = %x cmdat = %x\n", host->clkrt, host->cmdat); } diff --git a/drivers/mmc/sdhci.c b/drivers/mmc/sdhci.c index bdbfca05002..b0053280ff2 100644 --- a/drivers/mmc/sdhci.c +++ b/drivers/mmc/sdhci.c @@ -570,10 +570,6 @@ static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) spin_lock_irqsave(&host->lock, flags); - DBG("clock %uHz busmode %u powermode %u cs %u Vdd %u width %u\n", - ios->clock, ios->bus_mode, ios->power_mode, ios->chip_select, - ios->vdd, ios->bus_width); - /* * Reset the chip on each power off. * Should clear out any weird states. diff --git a/drivers/mmc/wbsd.c b/drivers/mmc/wbsd.c index 511f7b0b31d..39b3d97f891 100644 --- a/drivers/mmc/wbsd.c +++ b/drivers/mmc/wbsd.c @@ -931,10 +931,6 @@ static void wbsd_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) struct wbsd_host *host = mmc_priv(mmc); u8 clk, setup, pwr; - DBGF("clock %uHz busmode %u powermode %u cs %u Vdd %u width %u\n", - ios->clock, ios->bus_mode, ios->power_mode, ios->chip_select, - ios->vdd, ios->bus_width); - spin_lock_bh(&host->lock); /* diff --git a/drivers/net/au1000_eth.c b/drivers/net/au1000_eth.c index 1363083b4d8..14dbad14afb 100644 --- a/drivers/net/au1000_eth.c +++ b/drivers/net/au1000_eth.c @@ -52,6 +52,7 @@ #include <linux/mii.h> #include <linux/skbuff.h> #include <linux/delay.h> +#include <linux/crc32.h> #include <asm/mipsregs.h> #include <asm/irq.h> #include <asm/io.h> @@ -2070,23 +2071,6 @@ static void au1000_tx_timeout(struct net_device *dev) netif_wake_queue(dev); } - -static unsigned const ethernet_polynomial = 0x04c11db7U; -static inline u32 ether_crc(int length, unsigned char *data) -{ - int crc = -1; - - while(--length >= 0) { - unsigned char current_octet = *data++; - int bit; - for (bit = 0; bit < 8; bit++, current_octet >>= 1) - crc = (crc << 1) ^ - ((crc < 0) ^ (current_octet & 1) ? - ethernet_polynomial : 0); - } - return crc; -} - static void set_rx_mode(struct net_device *dev) { struct au1000_private *aup = (struct au1000_private *) dev->priv; diff --git a/drivers/net/dl2k.c b/drivers/net/dl2k.c index 1f3627470c9..1ddefd28121 100644 --- a/drivers/net/dl2k.c +++ b/drivers/net/dl2k.c @@ -765,7 +765,7 @@ rio_free_tx (struct net_device *dev, int irq) break; skb = np->tx_skbuff[entry]; pci_unmap_single (np->pdev, - np->tx_ring[entry].fraginfo & 0xffffffffffff, + np->tx_ring[entry].fraginfo & DMA_48BIT_MASK, skb->len, PCI_DMA_TODEVICE); if (irq) dev_kfree_skb_irq (skb); @@ -893,7 +893,7 @@ receive_packet (struct net_device *dev) /* Small skbuffs for short packets */ if (pkt_len > copy_thresh) { pci_unmap_single (np->pdev, - desc->fraginfo & 0xffffffffffff, + desc->fraginfo & DMA_48BIT_MASK, np->rx_buf_sz, PCI_DMA_FROMDEVICE); skb_put (skb = np->rx_skbuff[entry], pkt_len); @@ -901,7 +901,7 @@ receive_packet (struct net_device *dev) } else if ((skb = dev_alloc_skb (pkt_len + 2)) != NULL) { pci_dma_sync_single_for_cpu(np->pdev, desc->fraginfo & - 0xffffffffffff, + DMA_48BIT_MASK, np->rx_buf_sz, PCI_DMA_FROMDEVICE); skb->dev = dev; @@ -913,7 +913,7 @@ receive_packet (struct net_device *dev) skb_put (skb, pkt_len); pci_dma_sync_single_for_device(np->pdev, desc->fraginfo & - 0xffffffffffff, + DMA_48BIT_MASK, np->rx_buf_sz, PCI_DMA_FROMDEVICE); } @@ -1800,7 +1800,7 @@ rio_close (struct net_device *dev) skb = np->rx_skbuff[i]; if (skb) { pci_unmap_single(np->pdev, - np->rx_ring[i].fraginfo & 0xffffffffffff, + np->rx_ring[i].fraginfo & DMA_48BIT_MASK, skb->len, PCI_DMA_FROMDEVICE); dev_kfree_skb (skb); np->rx_skbuff[i] = NULL; @@ -1810,7 +1810,7 @@ rio_close (struct net_device *dev) skb = np->tx_skbuff[i]; if (skb) { pci_unmap_single(np->pdev, - np->tx_ring[i].fraginfo & 0xffffffffffff, + np->tx_ring[i].fraginfo & DMA_48BIT_MASK, skb->len, PCI_DMA_TODEVICE); dev_kfree_skb (skb); np->tx_skbuff[i] = NULL; diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c index 9788b1ef2e7..f7235c9bc42 100644 --- a/drivers/net/forcedeth.c +++ b/drivers/net/forcedeth.c @@ -106,6 +106,7 @@ * 0.51: 20 Jan 2006: Add 64bit consistent memory allocation for rings. * 0.52: 20 Jan 2006: Add MSI/MSIX support. * 0.53: 19 Mar 2006: Fix init from low power mode and add hw reset. + * 0.54: 21 Mar 2006: Fix spin locks for multi irqs and cleanup. * * Known bugs: * We suspect that on some hardware no TX done interrupts are generated. @@ -117,7 +118,7 @@ * DEV_NEED_TIMERIRQ will not harm you on sane hardware, only generating a few * superfluous timer interrupts from the nic. */ -#define FORCEDETH_VERSION "0.53" +#define FORCEDETH_VERSION "0.54" #define DRV_NAME "forcedeth" #include <linux/module.h> @@ -710,6 +711,72 @@ static void setup_hw_rings(struct net_device *dev, int rxtx_flags) } } +static int using_multi_irqs(struct net_device *dev) +{ + struct fe_priv *np = get_nvpriv(dev); + + if (!(np->msi_flags & NV_MSI_X_ENABLED) || + ((np->msi_flags & NV_MSI_X_ENABLED) && + ((np->msi_flags & NV_MSI_X_VECTORS_MASK) == 0x1))) + return 0; + else + return 1; +} + +static void nv_enable_irq(struct net_device *dev) +{ + struct fe_priv *np = get_nvpriv(dev); + + if (!using_multi_irqs(dev)) { + if (np->msi_flags & NV_MSI_X_ENABLED) + enable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_ALL].vector); + else + enable_irq(dev->irq); + } else { + enable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_RX].vector); + enable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_TX].vector); + enable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_OTHER].vector); + } +} + +static void nv_disable_irq(struct net_device *dev) +{ + struct fe_priv *np = get_nvpriv(dev); + + if (!using_multi_irqs(dev)) { + if (np->msi_flags & NV_MSI_X_ENABLED) + disable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_ALL].vector); + else + disable_irq(dev->irq); + } else { + disable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_RX].vector); + disable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_TX].vector); + disable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_OTHER].vector); + } +} + +/* In MSIX mode, a write to irqmask behaves as XOR */ +static void nv_enable_hw_interrupts(struct net_device *dev, u32 mask) +{ + u8 __iomem *base = get_hwbase(dev); + + writel(mask, base + NvRegIrqMask); +} + +static void nv_disable_hw_interrupts(struct net_device *dev, u32 mask) +{ + struct fe_priv *np = get_nvpriv(dev); + u8 __iomem *base = get_hwbase(dev); + + if (np->msi_flags & NV_MSI_X_ENABLED) { + writel(mask, base + NvRegIrqMask); + } else { + if (np->msi_flags & NV_MSI_ENABLED) + writel(0, base + NvRegMSIIrqMask); + writel(0, base + NvRegIrqMask); + } +} + #define MII_READ (-1) /* mii_rw: read/write a register on the PHY. * @@ -1019,24 +1086,25 @@ static void nv_do_rx_refill(unsigned long data) struct net_device *dev = (struct net_device *) data; struct fe_priv *np = netdev_priv(dev); - - if (!(np->msi_flags & NV_MSI_X_ENABLED) || - ((np->msi_flags & NV_MSI_X_ENABLED) && - ((np->msi_flags & NV_MSI_X_VECTORS_MASK) == 0x1))) { - disable_irq(dev->irq); + if (!using_multi_irqs(dev)) { + if (np->msi_flags & NV_MSI_X_ENABLED) + disable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_ALL].vector); + else + disable_irq(dev->irq); } else { disable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_RX].vector); } if (nv_alloc_rx(dev)) { - spin_lock(&np->lock); + spin_lock_irq(&np->lock); if (!np->in_shutdown) mod_timer(&np->oom_kick, jiffies + OOM_REFILL); - spin_unlock(&np->lock); + spin_unlock_irq(&np->lock); } - if (!(np->msi_flags & NV_MSI_X_ENABLED) || - ((np->msi_flags & NV_MSI_X_ENABLED) && - ((np->msi_flags & NV_MSI_X_VECTORS_MASK) == 0x1))) { - enable_irq(dev->irq); + if (!using_multi_irqs(dev)) { + if (np->msi_flags & NV_MSI_X_ENABLED) + enable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_ALL].vector); + else + enable_irq(dev->irq); } else { enable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_RX].vector); } @@ -1668,15 +1736,7 @@ static int nv_change_mtu(struct net_device *dev, int new_mtu) * guessed, there is probably a simpler approach. * Changing the MTU is a rare event, it shouldn't matter. */ - if (!(np->msi_flags & NV_MSI_X_ENABLED) || - ((np->msi_flags & NV_MSI_X_ENABLED) && - ((np->msi_flags & NV_MSI_X_VECTORS_MASK) == 0x1))) { - disable_irq(dev->irq); - } else { - disable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_RX].vector); - disable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_TX].vector); - disable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_OTHER].vector); - } + nv_disable_irq(dev); spin_lock_bh(&dev->xmit_lock); spin_lock(&np->lock); /* stop engines */ @@ -1709,15 +1769,7 @@ static int nv_change_mtu(struct net_device *dev, int new_mtu) nv_start_tx(dev); spin_unlock(&np->lock); spin_unlock_bh(&dev->xmit_lock); - if (!(np->msi_flags & NV_MSI_X_ENABLED) || - ((np->msi_flags & NV_MSI_X_ENABLED) && - ((np->msi_flags & NV_MSI_X_VECTORS_MASK) == 0x1))) { - enable_irq(dev->irq); - } else { - enable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_RX].vector); - enable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_TX].vector); - enable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_OTHER].vector); - } + nv_enable_irq(dev); } return 0; } @@ -2108,16 +2160,16 @@ static irqreturn_t nv_nic_irq_tx(int foo, void *data, struct pt_regs *regs) if (!(events & np->irqmask)) break; - spin_lock(&np->lock); + spin_lock_irq(&np->lock); nv_tx_done(dev); - spin_unlock(&np->lock); + spin_unlock_irq(&np->lock); if (events & (NVREG_IRQ_TX_ERR)) { dprintk(KERN_DEBUG "%s: received irq with events 0x%x. Probably TX fail.\n", dev->name, events); } if (i > max_interrupt_work) { - spin_lock(&np->lock); + spin_lock_irq(&np->lock); /* disable interrupts on the nic */ writel(NVREG_IRQ_TX_ALL, base + NvRegIrqMask); pci_push(base); @@ -2127,7 +2179,7 @@ static irqreturn_t nv_nic_irq_tx(int foo, void *data, struct pt_regs *regs) mod_timer(&np->nic_poll, jiffies + POLL_WAIT); } printk(KERN_DEBUG "%s: too many iterations (%d) in nv_nic_irq_tx.\n", dev->name, i); - spin_unlock(&np->lock); + spin_unlock_irq(&np->lock); break; } @@ -2157,14 +2209,14 @@ static irqreturn_t nv_nic_irq_rx(int foo, void *data, struct pt_regs *regs) nv_rx_process(dev); if (nv_alloc_rx(dev)) { - spin_lock(&np->lock); + spin_lock_irq(&np->lock); if (!np->in_shutdown) mod_timer(&np->oom_kick, jiffies + OOM_REFILL); - spin_unlock(&np->lock); + spin_unlock_irq(&np->lock); } if (i > max_interrupt_work) { - spin_lock(&np->lock); + spin_lock_irq(&np->lock); /* disable interrupts on the nic */ writel(NVREG_IRQ_RX_ALL, base + NvRegIrqMask); pci_push(base); @@ -2174,7 +2226,7 @@ static irqreturn_t nv_nic_irq_rx(int foo, void *data, struct pt_regs *regs) mod_timer(&np->nic_poll, jiffies + POLL_WAIT); } printk(KERN_DEBUG "%s: too many iterations (%d) in nv_nic_irq_rx.\n", dev->name, i); - spin_unlock(&np->lock); + spin_unlock_irq(&np->lock); break; } @@ -2203,14 +2255,14 @@ static irqreturn_t nv_nic_irq_other(int foo, void *data, struct pt_regs *regs) break; if (events & NVREG_IRQ_LINK) { - spin_lock(&np->lock); + spin_lock_irq(&np->lock); nv_link_irq(dev); - spin_unlock(&np->lock); + spin_unlock_irq(&np->lock); } if (np->need_linktimer && time_after(jiffies, np->link_timeout)) { - spin_lock(&np->lock); + spin_lock_irq(&np->lock); nv_linkchange(dev); - spin_unlock(&np->lock); + spin_unlock_irq(&np->lock); np->link_timeout = jiffies + LINK_TIMEOUT; } if (events & (NVREG_IRQ_UNKNOWN)) { @@ -2218,7 +2270,7 @@ static irqreturn_t nv_nic_irq_other(int foo, void *data, struct pt_regs *regs) dev->name, events); } if (i > max_interrupt_work) { - spin_lock(&np->lock); + spin_lock_irq(&np->lock); /* disable interrupts on the nic */ writel(NVREG_IRQ_OTHER, base + NvRegIrqMask); pci_push(base); @@ -2228,7 +2280,7 @@ static irqreturn_t nv_nic_irq_other(int foo, void *data, struct pt_regs *regs) mod_timer(&np->nic_poll, jiffies + POLL_WAIT); } printk(KERN_DEBUG "%s: too many iterations (%d) in nv_nic_irq_other.\n", dev->name, i); - spin_unlock(&np->lock); + spin_unlock_irq(&np->lock); break; } @@ -2251,10 +2303,11 @@ static void nv_do_nic_poll(unsigned long data) * nv_nic_irq because that may decide to do otherwise */ - if (!(np->msi_flags & NV_MSI_X_ENABLED) || - ((np->msi_flags & NV_MSI_X_ENABLED) && - ((np->msi_flags & NV_MSI_X_VECTORS_MASK) == 0x1))) { - disable_irq(dev->irq); + if (!using_multi_irqs(dev)) { + if (np->msi_flags & NV_MSI_X_ENABLED) + disable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_ALL].vector); + else + disable_irq(dev->irq); mask = np->irqmask; } else { if (np->nic_poll_irq & NVREG_IRQ_RX_ALL) { @@ -2277,11 +2330,12 @@ static void nv_do_nic_poll(unsigned long data) writel(mask, base + NvRegIrqMask); pci_push(base); - if (!(np->msi_flags & NV_MSI_X_ENABLED) || - ((np->msi_flags & NV_MSI_X_ENABLED) && - ((np->msi_flags & NV_MSI_X_VECTORS_MASK) == 0x1))) { + if (!using_multi_irqs(dev)) { nv_nic_irq((int) 0, (void *) data, (struct pt_regs *) NULL); - enable_irq(dev->irq); + if (np->msi_flags & NV_MSI_X_ENABLED) + enable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_ALL].vector); + else + enable_irq(dev->irq); } else { if (np->nic_poll_irq & NVREG_IRQ_RX_ALL) { nv_nic_irq_rx((int) 0, (void *) data, (struct pt_regs *) NULL); @@ -2628,6 +2682,113 @@ static void set_msix_vector_map(struct net_device *dev, u32 vector, u32 irqmask) writel(readl(base + NvRegMSIXMap1) | msixmap, base + NvRegMSIXMap1); } +static int nv_request_irq(struct net_device *dev) +{ + struct fe_priv *np = get_nvpriv(dev); + u8 __iomem *base = get_hwbase(dev); + int ret = 1; + int i; + + if (np->msi_flags & NV_MSI_X_CAPABLE) { + for (i = 0; i < (np->msi_flags & NV_MSI_X_VECTORS_MASK); i++) { + np->msi_x_entry[i].entry = i; + } + if ((ret = pci_enable_msix(np->pci_dev, np->msi_x_entry, (np->msi_flags & NV_MSI_X_VECTORS_MASK))) == 0) { + np->msi_flags |= NV_MSI_X_ENABLED; + if (optimization_mode == NV_OPTIMIZATION_MODE_THROUGHPUT) { + /* Request irq for rx handling */ + if (request_irq(np->msi_x_entry[NV_MSI_X_VECTOR_RX].vector, &nv_nic_irq_rx, SA_SHIRQ, dev->name, dev) != 0) { + printk(KERN_INFO "forcedeth: request_irq failed for rx %d\n", ret); + pci_disable_msix(np->pci_dev); + np->msi_flags &= ~NV_MSI_X_ENABLED; + goto out_err; + } + /* Request irq for tx handling */ + if (request_irq(np->msi_x_entry[NV_MSI_X_VECTOR_TX].vector, &nv_nic_irq_tx, SA_SHIRQ, dev->name, dev) != 0) { + printk(KERN_INFO "forcedeth: request_irq failed for tx %d\n", ret); + pci_disable_msix(np->pci_dev); + np->msi_flags &= ~NV_MSI_X_ENABLED; + goto out_free_rx; + } + /* Request irq for link and timer handling */ + if (request_irq(np->msi_x_entry[NV_MSI_X_VECTOR_OTHER].vector, &nv_nic_irq_other, SA_SHIRQ, dev->name, dev) != 0) { + printk(KERN_INFO "forcedeth: request_irq failed for link %d\n", ret); + pci_disable_msix(np->pci_dev); + np->msi_flags &= ~NV_MSI_X_ENABLED; + goto out_free_tx; + } + /* map interrupts to their respective vector */ + writel(0, base + NvRegMSIXMap0); + writel(0, base + NvRegMSIXMap1); + set_msix_vector_map(dev, NV_MSI_X_VECTOR_RX, NVREG_IRQ_RX_ALL); + set_msix_vector_map(dev, NV_MSI_X_VECTOR_TX, NVREG_IRQ_TX_ALL); + set_msix_vector_map(dev, NV_MSI_X_VECTOR_OTHER, NVREG_IRQ_OTHER); + } else { + /* Request irq for all interrupts */ + if (request_irq(np->msi_x_entry[NV_MSI_X_VECTOR_ALL].vector, &nv_nic_irq, SA_SHIRQ, dev->name, dev) != 0) { + printk(KERN_INFO "forcedeth: request_irq failed %d\n", ret); + pci_disable_msix(np->pci_dev); + np->msi_flags &= ~NV_MSI_X_ENABLED; + goto out_err; + } + + /* map interrupts to vector 0 */ + writel(0, base + NvRegMSIXMap0); + writel(0, base + NvRegMSIXMap1); + } + } + } + if (ret != 0 && np->msi_flags & NV_MSI_CAPABLE) { + if ((ret = pci_enable_msi(np->pci_dev)) == 0) { + np->msi_flags |= NV_MSI_ENABLED; + if (request_irq(np->pci_dev->irq, &nv_nic_irq, SA_SHIRQ, dev->name, dev) != 0) { + printk(KERN_INFO "forcedeth: request_irq failed %d\n", ret); + pci_disable_msi(np->pci_dev); + np->msi_flags &= ~NV_MSI_ENABLED; + goto out_err; + } + + /* map interrupts to vector 0 */ + writel(0, base + NvRegMSIMap0); + writel(0, base + NvRegMSIMap1); + /* enable msi vector 0 */ + writel(NVREG_MSI_VECTOR_0_ENABLED, base + NvRegMSIIrqMask); + } + } + if (ret != 0) { + if (request_irq(np->pci_dev->irq, &nv_nic_irq, SA_SHIRQ, dev->name, dev) != 0) + goto out_err; + } + + return 0; +out_free_tx: + free_irq(np->msi_x_entry[NV_MSI_X_VECTOR_TX].vector, dev); +out_free_rx: + free_irq(np->msi_x_entry[NV_MSI_X_VECTOR_RX].vector, dev); +out_err: + return 1; +} + +static void nv_free_irq(struct net_device *dev) +{ + struct fe_priv *np = get_nvpriv(dev); + int i; + + if (np->msi_flags & NV_MSI_X_ENABLED) { + for (i = 0; i < (np->msi_flags & NV_MSI_X_VECTORS_MASK); i++) { + free_irq(np->msi_x_entry[i].vector, dev); + } + pci_disable_msix(np->pci_dev); + np->msi_flags &= ~NV_MSI_X_ENABLED; + } else { + free_irq(np->pci_dev->irq, dev); + if (np->msi_flags & NV_MSI_ENABLED) { + pci_disable_msi(np->pci_dev); + np->msi_flags &= ~NV_MSI_ENABLED; + } + } +} + static int nv_open(struct net_device *dev) { struct fe_priv *np = netdev_priv(dev); @@ -2720,12 +2881,16 @@ static int nv_open(struct net_device *dev) udelay(10); writel(readl(base + NvRegPowerState) | NVREG_POWERSTATE_VALID, base + NvRegPowerState); - writel(0, base + NvRegIrqMask); + nv_disable_hw_interrupts(dev, np->irqmask); pci_push(base); writel(NVREG_MIISTAT_MASK2, base + NvRegMIIStatus); writel(NVREG_IRQSTAT_MASK, base + NvRegIrqStatus); pci_push(base); + if (nv_request_irq(dev)) { + goto out_drain; + } + if (np->msi_flags & NV_MSI_X_CAPABLE) { for (i = 0; i < (np->msi_flags & NV_MSI_X_VECTORS_MASK); i++) { np->msi_x_entry[i].entry = i; @@ -2799,7 +2964,7 @@ static int nv_open(struct net_device *dev) } /* ask for interrupts */ - writel(np->irqmask, base + NvRegIrqMask); + nv_enable_hw_interrupts(dev, np->irqmask); spin_lock_irq(&np->lock); writel(NVREG_MCASTADDRA_FORCE, base + NvRegMulticastAddrA); @@ -2843,7 +3008,6 @@ static int nv_close(struct net_device *dev) { struct fe_priv *np = netdev_priv(dev); u8 __iomem *base; - int i; spin_lock_irq(&np->lock); np->in_shutdown = 1; @@ -2861,31 +3025,13 @@ static int nv_close(struct net_device *dev) /* disable interrupts on the nic or we will lock up */ base = get_hwbase(dev); - if (np->msi_flags & NV_MSI_X_ENABLED) { - writel(np->irqmask, base + NvRegIrqMask); - } else { - if (np->msi_flags & NV_MSI_ENABLED) - writel(0, base + NvRegMSIIrqMask); - writel(0, base + NvRegIrqMask); - } + nv_disable_hw_interrupts(dev, np->irqmask); pci_push(base); dprintk(KERN_INFO "%s: Irqmask is zero again\n", dev->name); spin_unlock_irq(&np->lock); - if (np->msi_flags & NV_MSI_X_ENABLED) { - for (i = 0; i < (np->msi_flags & NV_MSI_X_VECTORS_MASK); i++) { - free_irq(np->msi_x_entry[i].vector, dev); - } - pci_disable_msix(np->pci_dev); - np->msi_flags &= ~NV_MSI_X_ENABLED; - } else { - free_irq(np->pci_dev->irq, dev); - if (np->msi_flags & NV_MSI_ENABLED) { - pci_disable_msi(np->pci_dev); - np->msi_flags &= ~NV_MSI_ENABLED; - } - } + nv_free_irq(dev); drain_ring(dev); @@ -2974,20 +3120,18 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i if (id->driver_data & DEV_HAS_HIGH_DMA) { /* packet format 3: supports 40-bit addressing */ np->desc_ver = DESC_VER_3; + np->txrxctl_bits = NVREG_TXRXCTL_DESC_3; if (pci_set_dma_mask(pci_dev, DMA_39BIT_MASK)) { printk(KERN_INFO "forcedeth: 64-bit DMA failed, using 32-bit addressing for device %s.\n", pci_name(pci_dev)); } else { - if (pci_set_consistent_dma_mask(pci_dev, 0x0000007fffffffffULL)) { - printk(KERN_INFO "forcedeth: 64-bit DMA (consistent) failed for device %s.\n", - pci_name(pci_dev)); - goto out_relreg; - } else { - dev->features |= NETIF_F_HIGHDMA; - printk(KERN_INFO "forcedeth: using HIGHDMA\n"); - } + dev->features |= NETIF_F_HIGHDMA; + printk(KERN_INFO "forcedeth: using HIGHDMA\n"); + } + if (pci_set_consistent_dma_mask(pci_dev, 0x0000007fffffffffULL)) { + printk(KERN_INFO "forcedeth: 64-bit DMA (consistent) failed for device %s.\n", + pci_name(pci_dev)); } - np->txrxctl_bits = NVREG_TXRXCTL_DESC_3; } else if (id->driver_data & DEV_HAS_LARGEDESC) { /* packet format 2: supports jumbo frames */ np->desc_ver = DESC_VER_2; diff --git a/drivers/net/hamradio/dmascc.c b/drivers/net/hamradio/dmascc.c index 79a8fbcf5f9..0d5fccc984b 100644 --- a/drivers/net/hamradio/dmascc.c +++ b/drivers/net/hamradio/dmascc.c @@ -582,7 +582,6 @@ static int __init setup_adapter(int card_base, int type, int n) INIT_WORK(&priv->rx_work, rx_bh, priv); dev->priv = priv; sprintf(dev->name, "dmascc%i", 2 * n + i); - SET_MODULE_OWNER(dev); dev->base_addr = card_base; dev->irq = irq; dev->open = scc_open; diff --git a/drivers/net/hamradio/scc.c b/drivers/net/hamradio/scc.c index 6ace0e914fd..5927784df3f 100644 --- a/drivers/net/hamradio/scc.c +++ b/drivers/net/hamradio/scc.c @@ -1550,7 +1550,6 @@ static unsigned char ax25_nocall[AX25_ADDR_LEN] = static void scc_net_setup(struct net_device *dev) { - SET_MODULE_OWNER(dev); dev->tx_queue_len = 16; /* should be enough... */ dev->open = scc_net_open; diff --git a/drivers/net/hamradio/yam.c b/drivers/net/hamradio/yam.c index fe22479eb20..b49884048ca 100644 --- a/drivers/net/hamradio/yam.c +++ b/drivers/net/hamradio/yam.c @@ -1098,7 +1098,6 @@ static void yam_setup(struct net_device *dev) dev->base_addr = yp->iobase; dev->irq = yp->irq; - SET_MODULE_OWNER(dev); dev->open = yam_open; dev->stop = yam_close; diff --git a/drivers/net/irda/Makefile b/drivers/net/irda/Makefile index 27ab75f2079..c1ce2398efe 100644 --- a/drivers/net/irda/Makefile +++ b/drivers/net/irda/Makefile @@ -46,4 +46,4 @@ obj-$(CONFIG_MA600_DONGLE) += ma600-sir.o obj-$(CONFIG_TOIM3232_DONGLE) += toim3232-sir.o # The SIR helper module -sir-dev-objs := sir_dev.o sir_dongle.o sir_kthread.o +sir-dev-objs := sir_dev.o sir_dongle.o diff --git a/drivers/net/irda/irda-usb.c b/drivers/net/irda/irda-usb.c index 96bdb73c228..cd87593e4e8 100644 --- a/drivers/net/irda/irda-usb.c +++ b/drivers/net/irda/irda-usb.c @@ -1778,7 +1778,7 @@ static int irda_usb_probe(struct usb_interface *intf, if (self->needspatch) { ret = usb_control_msg (self->usbdev, usb_sndctrlpipe (self->usbdev, 0), - 0x02, 0x40, 0, 0, 0, 0, msecs_to_jiffies(500)); + 0x02, 0x40, 0, 0, NULL, 0, 500); if (ret < 0) { IRDA_DEBUG (0, "usb_control_msg failed %d\n", ret); goto err_out_3; diff --git a/drivers/net/irda/sir-dev.h b/drivers/net/irda/sir-dev.h index f69fb4cec76..9fa294a546d 100644 --- a/drivers/net/irda/sir-dev.h +++ b/drivers/net/irda/sir-dev.h @@ -15,23 +15,14 @@ #define IRDA_SIR_H #include <linux/netdevice.h> +#include <linux/workqueue.h> #include <net/irda/irda.h> #include <net/irda/irda_device.h> // iobuff_t -/* FIXME: unify irda_request with sir_fsm! */ - -struct irda_request { - struct list_head lh_request; - unsigned long pending; - void (*func)(void *); - void *data; - struct timer_list timer; -}; - struct sir_fsm { struct semaphore sem; - struct irda_request rq; + struct work_struct work; unsigned state, substate; int param; int result; diff --git a/drivers/net/irda/sir_dev.c b/drivers/net/irda/sir_dev.c index ea7c9464d46..3b5854d10c1 100644 --- a/drivers/net/irda/sir_dev.c +++ b/drivers/net/irda/sir_dev.c @@ -23,6 +23,298 @@ #include "sir-dev.h" + +static struct workqueue_struct *irda_sir_wq; + +/* STATE MACHINE */ + +/* substate handler of the config-fsm to handle the cases where we want + * to wait for transmit completion before changing the port configuration + */ + +static int sirdev_tx_complete_fsm(struct sir_dev *dev) +{ + struct sir_fsm *fsm = &dev->fsm; + unsigned next_state, delay; + unsigned bytes_left; + + do { + next_state = fsm->substate; /* default: stay in current substate */ + delay = 0; + + switch(fsm->substate) { + + case SIRDEV_STATE_WAIT_XMIT: + if (dev->drv->chars_in_buffer) + bytes_left = dev->drv->chars_in_buffer(dev); + else + bytes_left = 0; + if (!bytes_left) { + next_state = SIRDEV_STATE_WAIT_UNTIL_SENT; + break; + } + + if (dev->speed > 115200) + delay = (bytes_left*8*10000) / (dev->speed/100); + else if (dev->speed > 0) + delay = (bytes_left*10*10000) / (dev->speed/100); + else + delay = 0; + /* expected delay (usec) until remaining bytes are sent */ + if (delay < 100) { + udelay(delay); + delay = 0; + break; + } + /* sleep some longer delay (msec) */ + delay = (delay+999) / 1000; + break; + + case SIRDEV_STATE_WAIT_UNTIL_SENT: + /* block until underlaying hardware buffer are empty */ + if (dev->drv->wait_until_sent) + dev->drv->wait_until_sent(dev); + next_state = SIRDEV_STATE_TX_DONE; + break; + + case SIRDEV_STATE_TX_DONE: + return 0; + + default: + IRDA_ERROR("%s - undefined state\n", __FUNCTION__); + return -EINVAL; + } + fsm->substate = next_state; + } while (delay == 0); + return delay; +} + +/* + * Function sirdev_config_fsm + * + * State machine to handle the configuration of the device (and attached dongle, if any). + * This handler is scheduled for execution in kIrDAd context, so we can sleep. + * however, kIrDAd is shared by all sir_dev devices so we better don't sleep there too + * long. Instead, for longer delays we start a timer to reschedule us later. + * On entry, fsm->sem is always locked and the netdev xmit queue stopped. + * Both must be unlocked/restarted on completion - but only on final exit. + */ + +static void sirdev_config_fsm(void *data) +{ + struct sir_dev *dev = data; + struct sir_fsm *fsm = &dev->fsm; + int next_state; + int ret = -1; + unsigned delay; + + IRDA_DEBUG(2, "%s(), <%ld>\n", __FUNCTION__, jiffies); + + do { + IRDA_DEBUG(3, "%s - state=0x%04x / substate=0x%04x\n", + __FUNCTION__, fsm->state, fsm->substate); + + next_state = fsm->state; + delay = 0; + + switch(fsm->state) { + + case SIRDEV_STATE_DONGLE_OPEN: + if (dev->dongle_drv != NULL) { + ret = sirdev_put_dongle(dev); + if (ret) { + fsm->result = -EINVAL; + next_state = SIRDEV_STATE_ERROR; + break; + } + } + + /* Initialize dongle */ + ret = sirdev_get_dongle(dev, fsm->param); + if (ret) { + fsm->result = ret; + next_state = SIRDEV_STATE_ERROR; + break; + } + + /* Dongles are powered through the modem control lines which + * were just set during open. Before resetting, let's wait for + * the power to stabilize. This is what some dongle drivers did + * in open before, while others didn't - should be safe anyway. + */ + + delay = 50; + fsm->substate = SIRDEV_STATE_DONGLE_RESET; + next_state = SIRDEV_STATE_DONGLE_RESET; + + fsm->param = 9600; + + break; + + case SIRDEV_STATE_DONGLE_CLOSE: + /* shouldn't we just treat this as success=? */ + if (dev->dongle_drv == NULL) { + fsm->result = -EINVAL; + next_state = SIRDEV_STATE_ERROR; + break; + } + + ret = sirdev_put_dongle(dev); + if (ret) { + fsm->result = ret; + next_state = SIRDEV_STATE_ERROR; + break; + } + next_state = SIRDEV_STATE_DONE; + break; + + case SIRDEV_STATE_SET_DTR_RTS: + ret = sirdev_set_dtr_rts(dev, + (fsm->param&0x02) ? TRUE : FALSE, + (fsm->param&0x01) ? TRUE : FALSE); + next_state = SIRDEV_STATE_DONE; + break; + + case SIRDEV_STATE_SET_SPEED: + fsm->substate = SIRDEV_STATE_WAIT_XMIT; + next_state = SIRDEV_STATE_DONGLE_CHECK; + break; + + case SIRDEV_STATE_DONGLE_CHECK: + ret = sirdev_tx_complete_fsm(dev); + if (ret < 0) { + fsm->result = ret; + next_state = SIRDEV_STATE_ERROR; + break; + } + if ((delay=ret) != 0) + break; + + if (dev->dongle_drv) { + fsm->substate = SIRDEV_STATE_DONGLE_RESET; + next_state = SIRDEV_STATE_DONGLE_RESET; + } + else { + dev->speed = fsm->param; + next_state = SIRDEV_STATE_PORT_SPEED; + } + break; + + case SIRDEV_STATE_DONGLE_RESET: + if (dev->dongle_drv->reset) { + ret = dev->dongle_drv->reset(dev); + if (ret < 0) { + fsm->result = ret; + next_state = SIRDEV_STATE_ERROR; + break; + } + } + else + ret = 0; + if ((delay=ret) == 0) { + /* set serial port according to dongle default speed */ + if (dev->drv->set_speed) + dev->drv->set_speed(dev, dev->speed); + fsm->substate = SIRDEV_STATE_DONGLE_SPEED; + next_state = SIRDEV_STATE_DONGLE_SPEED; + } + break; + + case SIRDEV_STATE_DONGLE_SPEED: + if (dev->dongle_drv->reset) { + ret = dev->dongle_drv->set_speed(dev, fsm->param); + if (ret < 0) { + fsm->result = ret; + next_state = SIRDEV_STATE_ERROR; + break; + } + } + else + ret = 0; + if ((delay=ret) == 0) + next_state = SIRDEV_STATE_PORT_SPEED; + break; + + case SIRDEV_STATE_PORT_SPEED: + /* Finally we are ready to change the serial port speed */ + if (dev->drv->set_speed) + dev->drv->set_speed(dev, dev->speed); + dev->new_speed = 0; + next_state = SIRDEV_STATE_DONE; + break; + + case SIRDEV_STATE_DONE: + /* Signal network layer so it can send more frames */ + netif_wake_queue(dev->netdev); + next_state = SIRDEV_STATE_COMPLETE; + break; + + default: + IRDA_ERROR("%s - undefined state\n", __FUNCTION__); + fsm->result = -EINVAL; + /* fall thru */ + + case SIRDEV_STATE_ERROR: + IRDA_ERROR("%s - error: %d\n", __FUNCTION__, fsm->result); + +#if 0 /* don't enable this before we have netdev->tx_timeout to recover */ + netif_stop_queue(dev->netdev); +#else + netif_wake_queue(dev->netdev); +#endif + /* fall thru */ + + case SIRDEV_STATE_COMPLETE: + /* config change finished, so we are not busy any longer */ + sirdev_enable_rx(dev); + up(&fsm->sem); + return; + } + fsm->state = next_state; + } while(!delay); + + queue_delayed_work(irda_sir_wq, &fsm->work, msecs_to_jiffies(delay)); +} + +/* schedule some device configuration task for execution by kIrDAd + * on behalf of the above state machine. + * can be called from process or interrupt/tasklet context. + */ + +int sirdev_schedule_request(struct sir_dev *dev, int initial_state, unsigned param) +{ + struct sir_fsm *fsm = &dev->fsm; + + IRDA_DEBUG(2, "%s - state=0x%04x / param=%u\n", __FUNCTION__, initial_state, param); + + if (down_trylock(&fsm->sem)) { + if (in_interrupt() || in_atomic() || irqs_disabled()) { + IRDA_DEBUG(1, "%s(), state machine busy!\n", __FUNCTION__); + return -EWOULDBLOCK; + } else + down(&fsm->sem); + } + + if (fsm->state == SIRDEV_STATE_DEAD) { + /* race with sirdev_close should never happen */ + IRDA_ERROR("%s(), instance staled!\n", __FUNCTION__); + up(&fsm->sem); + return -ESTALE; /* or better EPIPE? */ + } + + netif_stop_queue(dev->netdev); + atomic_set(&dev->enable_rx, 0); + + fsm->state = initial_state; + fsm->param = param; + fsm->result = 0; + + INIT_WORK(&fsm->work, sirdev_config_fsm, dev); + queue_work(irda_sir_wq, &fsm->work); + return 0; +} + + /***************************************************************************/ void sirdev_enable_rx(struct sir_dev *dev) @@ -619,10 +911,6 @@ struct sir_dev * sirdev_get_instance(const struct sir_driver *drv, const char *n spin_lock_init(&dev->tx_lock); init_MUTEX(&dev->fsm.sem); - INIT_LIST_HEAD(&dev->fsm.rq.lh_request); - dev->fsm.rq.pending = 0; - init_timer(&dev->fsm.rq.timer); - dev->drv = drv; dev->netdev = ndev; @@ -682,3 +970,22 @@ int sirdev_put_instance(struct sir_dev *dev) } EXPORT_SYMBOL(sirdev_put_instance); +static int __init sir_wq_init(void) +{ + irda_sir_wq = create_singlethread_workqueue("irda_sir_wq"); + if (!irda_sir_wq) + return -ENOMEM; + return 0; +} + +static void __exit sir_wq_exit(void) +{ + destroy_workqueue(irda_sir_wq); +} + +module_init(sir_wq_init); +module_exit(sir_wq_exit); + +MODULE_AUTHOR("Martin Diehl <info@mdiehl.de>"); +MODULE_DESCRIPTION("IrDA SIR core"); +MODULE_LICENSE("GPL"); diff --git a/drivers/net/irda/sir_kthread.c b/drivers/net/irda/sir_kthread.c deleted file mode 100644 index e3904d6bfec..00000000000 --- a/drivers/net/irda/sir_kthread.c +++ /dev/null @@ -1,508 +0,0 @@ -/********************************************************************* - * - * sir_kthread.c: dedicated thread to process scheduled - * sir device setup requests - * - * Copyright (c) 2002 Martin Diehl - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - ********************************************************************/ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/version.h> -#include <linux/init.h> -#include <linux/smp_lock.h> -#include <linux/completion.h> -#include <linux/delay.h> - -#include <net/irda/irda.h> - -#include "sir-dev.h" - -/************************************************************************** - * - * kIrDAd kernel thread and config state machine - * - */ - -struct irda_request_queue { - struct list_head request_list; - spinlock_t lock; - task_t *thread; - struct completion exit; - wait_queue_head_t kick, done; - atomic_t num_pending; -}; - -static struct irda_request_queue irda_rq_queue; - -static int irda_queue_request(struct irda_request *rq) -{ - int ret = 0; - unsigned long flags; - - if (!test_and_set_bit(0, &rq->pending)) { - spin_lock_irqsave(&irda_rq_queue.lock, flags); - list_add_tail(&rq->lh_request, &irda_rq_queue.request_list); - wake_up(&irda_rq_queue.kick); - atomic_inc(&irda_rq_queue.num_pending); - spin_unlock_irqrestore(&irda_rq_queue.lock, flags); - ret = 1; - } - return ret; -} - -static void irda_request_timer(unsigned long data) -{ - struct irda_request *rq = (struct irda_request *)data; - unsigned long flags; - - spin_lock_irqsave(&irda_rq_queue.lock, flags); - list_add_tail(&rq->lh_request, &irda_rq_queue.request_list); - wake_up(&irda_rq_queue.kick); - spin_unlock_irqrestore(&irda_rq_queue.lock, flags); -} - -static int irda_queue_delayed_request(struct irda_request *rq, unsigned long delay) -{ - int ret = 0; - struct timer_list *timer = &rq->timer; - - if (!test_and_set_bit(0, &rq->pending)) { - timer->expires = jiffies + delay; - timer->function = irda_request_timer; - timer->data = (unsigned long)rq; - atomic_inc(&irda_rq_queue.num_pending); - add_timer(timer); - ret = 1; - } - return ret; -} - -static void run_irda_queue(void) -{ - unsigned long flags; - struct list_head *entry, *tmp; - struct irda_request *rq; - - spin_lock_irqsave(&irda_rq_queue.lock, flags); - list_for_each_safe(entry, tmp, &irda_rq_queue.request_list) { - rq = list_entry(entry, struct irda_request, lh_request); - list_del_init(entry); - spin_unlock_irqrestore(&irda_rq_queue.lock, flags); - - clear_bit(0, &rq->pending); - rq->func(rq->data); - - if (atomic_dec_and_test(&irda_rq_queue.num_pending)) - wake_up(&irda_rq_queue.done); - - spin_lock_irqsave(&irda_rq_queue.lock, flags); - } - spin_unlock_irqrestore(&irda_rq_queue.lock, flags); -} - -static int irda_thread(void *startup) -{ - DECLARE_WAITQUEUE(wait, current); - - daemonize("kIrDAd"); - - irda_rq_queue.thread = current; - - complete((struct completion *)startup); - - while (irda_rq_queue.thread != NULL) { - - /* We use TASK_INTERRUPTIBLE, rather than - * TASK_UNINTERRUPTIBLE. Andrew Morton made this - * change ; he told me that it is safe, because "signal - * blocking is now handled in daemonize()", he added - * that the problem is that "uninterruptible sleep - * contributes to load average", making user worry. - * Jean II */ - set_task_state(current, TASK_INTERRUPTIBLE); - add_wait_queue(&irda_rq_queue.kick, &wait); - if (list_empty(&irda_rq_queue.request_list)) - schedule(); - else - __set_task_state(current, TASK_RUNNING); - remove_wait_queue(&irda_rq_queue.kick, &wait); - - /* make swsusp happy with our thread */ - try_to_freeze(); - - run_irda_queue(); - } - -#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,35) - reparent_to_init(); -#endif - complete_and_exit(&irda_rq_queue.exit, 0); - /* never reached */ - return 0; -} - - -static void flush_irda_queue(void) -{ - if (atomic_read(&irda_rq_queue.num_pending)) { - - DECLARE_WAITQUEUE(wait, current); - - if (!list_empty(&irda_rq_queue.request_list)) - run_irda_queue(); - - set_task_state(current, TASK_UNINTERRUPTIBLE); - add_wait_queue(&irda_rq_queue.done, &wait); - if (atomic_read(&irda_rq_queue.num_pending)) - schedule(); - else - __set_task_state(current, TASK_RUNNING); - remove_wait_queue(&irda_rq_queue.done, &wait); - } -} - -/* substate handler of the config-fsm to handle the cases where we want - * to wait for transmit completion before changing the port configuration - */ - -static int irda_tx_complete_fsm(struct sir_dev *dev) -{ - struct sir_fsm *fsm = &dev->fsm; - unsigned next_state, delay; - unsigned bytes_left; - - do { - next_state = fsm->substate; /* default: stay in current substate */ - delay = 0; - - switch(fsm->substate) { - - case SIRDEV_STATE_WAIT_XMIT: - if (dev->drv->chars_in_buffer) - bytes_left = dev->drv->chars_in_buffer(dev); - else - bytes_left = 0; - if (!bytes_left) { - next_state = SIRDEV_STATE_WAIT_UNTIL_SENT; - break; - } - - if (dev->speed > 115200) - delay = (bytes_left*8*10000) / (dev->speed/100); - else if (dev->speed > 0) - delay = (bytes_left*10*10000) / (dev->speed/100); - else - delay = 0; - /* expected delay (usec) until remaining bytes are sent */ - if (delay < 100) { - udelay(delay); - delay = 0; - break; - } - /* sleep some longer delay (msec) */ - delay = (delay+999) / 1000; - break; - - case SIRDEV_STATE_WAIT_UNTIL_SENT: - /* block until underlaying hardware buffer are empty */ - if (dev->drv->wait_until_sent) - dev->drv->wait_until_sent(dev); - next_state = SIRDEV_STATE_TX_DONE; - break; - - case SIRDEV_STATE_TX_DONE: - return 0; - - default: - IRDA_ERROR("%s - undefined state\n", __FUNCTION__); - return -EINVAL; - } - fsm->substate = next_state; - } while (delay == 0); - return delay; -} - -/* - * Function irda_config_fsm - * - * State machine to handle the configuration of the device (and attached dongle, if any). - * This handler is scheduled for execution in kIrDAd context, so we can sleep. - * however, kIrDAd is shared by all sir_dev devices so we better don't sleep there too - * long. Instead, for longer delays we start a timer to reschedule us later. - * On entry, fsm->sem is always locked and the netdev xmit queue stopped. - * Both must be unlocked/restarted on completion - but only on final exit. - */ - -static void irda_config_fsm(void *data) -{ - struct sir_dev *dev = data; - struct sir_fsm *fsm = &dev->fsm; - int next_state; - int ret = -1; - unsigned delay; - - IRDA_DEBUG(2, "%s(), <%ld>\n", __FUNCTION__, jiffies); - - do { - IRDA_DEBUG(3, "%s - state=0x%04x / substate=0x%04x\n", - __FUNCTION__, fsm->state, fsm->substate); - - next_state = fsm->state; - delay = 0; - - switch(fsm->state) { - - case SIRDEV_STATE_DONGLE_OPEN: - if (dev->dongle_drv != NULL) { - ret = sirdev_put_dongle(dev); - if (ret) { - fsm->result = -EINVAL; - next_state = SIRDEV_STATE_ERROR; - break; - } - } - - /* Initialize dongle */ - ret = sirdev_get_dongle(dev, fsm->param); - if (ret) { - fsm->result = ret; - next_state = SIRDEV_STATE_ERROR; - break; - } - - /* Dongles are powered through the modem control lines which - * were just set during open. Before resetting, let's wait for - * the power to stabilize. This is what some dongle drivers did - * in open before, while others didn't - should be safe anyway. - */ - - delay = 50; - fsm->substate = SIRDEV_STATE_DONGLE_RESET; - next_state = SIRDEV_STATE_DONGLE_RESET; - - fsm->param = 9600; - - break; - - case SIRDEV_STATE_DONGLE_CLOSE: - /* shouldn't we just treat this as success=? */ - if (dev->dongle_drv == NULL) { - fsm->result = -EINVAL; - next_state = SIRDEV_STATE_ERROR; - break; - } - - ret = sirdev_put_dongle(dev); - if (ret) { - fsm->result = ret; - next_state = SIRDEV_STATE_ERROR; - break; - } - next_state = SIRDEV_STATE_DONE; - break; - - case SIRDEV_STATE_SET_DTR_RTS: - ret = sirdev_set_dtr_rts(dev, - (fsm->param&0x02) ? TRUE : FALSE, - (fsm->param&0x01) ? TRUE : FALSE); - next_state = SIRDEV_STATE_DONE; - break; - - case SIRDEV_STATE_SET_SPEED: - fsm->substate = SIRDEV_STATE_WAIT_XMIT; - next_state = SIRDEV_STATE_DONGLE_CHECK; - break; - - case SIRDEV_STATE_DONGLE_CHECK: - ret = irda_tx_complete_fsm(dev); - if (ret < 0) { - fsm->result = ret; - next_state = SIRDEV_STATE_ERROR; - break; - } - if ((delay=ret) != 0) - break; - - if (dev->dongle_drv) { - fsm->substate = SIRDEV_STATE_DONGLE_RESET; - next_state = SIRDEV_STATE_DONGLE_RESET; - } - else { - dev->speed = fsm->param; - next_state = SIRDEV_STATE_PORT_SPEED; - } - break; - - case SIRDEV_STATE_DONGLE_RESET: - if (dev->dongle_drv->reset) { - ret = dev->dongle_drv->reset(dev); - if (ret < 0) { - fsm->result = ret; - next_state = SIRDEV_STATE_ERROR; - break; - } - } - else - ret = 0; - if ((delay=ret) == 0) { - /* set serial port according to dongle default speed */ - if (dev->drv->set_speed) - dev->drv->set_speed(dev, dev->speed); - fsm->substate = SIRDEV_STATE_DONGLE_SPEED; - next_state = SIRDEV_STATE_DONGLE_SPEED; - } - break; - - case SIRDEV_STATE_DONGLE_SPEED: - if (dev->dongle_drv->reset) { - ret = dev->dongle_drv->set_speed(dev, fsm->param); - if (ret < 0) { - fsm->result = ret; - next_state = SIRDEV_STATE_ERROR; - break; - } - } - else - ret = 0; - if ((delay=ret) == 0) - next_state = SIRDEV_STATE_PORT_SPEED; - break; - - case SIRDEV_STATE_PORT_SPEED: - /* Finally we are ready to change the serial port speed */ - if (dev->drv->set_speed) - dev->drv->set_speed(dev, dev->speed); - dev->new_speed = 0; - next_state = SIRDEV_STATE_DONE; - break; - - case SIRDEV_STATE_DONE: - /* Signal network layer so it can send more frames */ - netif_wake_queue(dev->netdev); - next_state = SIRDEV_STATE_COMPLETE; - break; - - default: - IRDA_ERROR("%s - undefined state\n", __FUNCTION__); - fsm->result = -EINVAL; - /* fall thru */ - - case SIRDEV_STATE_ERROR: - IRDA_ERROR("%s - error: %d\n", __FUNCTION__, fsm->result); - -#if 0 /* don't enable this before we have netdev->tx_timeout to recover */ - netif_stop_queue(dev->netdev); -#else - netif_wake_queue(dev->netdev); -#endif - /* fall thru */ - - case SIRDEV_STATE_COMPLETE: - /* config change finished, so we are not busy any longer */ - sirdev_enable_rx(dev); - up(&fsm->sem); - return; - } - fsm->state = next_state; - } while(!delay); - - irda_queue_delayed_request(&fsm->rq, msecs_to_jiffies(delay)); -} - -/* schedule some device configuration task for execution by kIrDAd - * on behalf of the above state machine. - * can be called from process or interrupt/tasklet context. - */ - -int sirdev_schedule_request(struct sir_dev *dev, int initial_state, unsigned param) -{ - struct sir_fsm *fsm = &dev->fsm; - int xmit_was_down; - - IRDA_DEBUG(2, "%s - state=0x%04x / param=%u\n", __FUNCTION__, initial_state, param); - - if (down_trylock(&fsm->sem)) { - if (in_interrupt() || in_atomic() || irqs_disabled()) { - IRDA_DEBUG(1, "%s(), state machine busy!\n", __FUNCTION__); - return -EWOULDBLOCK; - } else - down(&fsm->sem); - } - - if (fsm->state == SIRDEV_STATE_DEAD) { - /* race with sirdev_close should never happen */ - IRDA_ERROR("%s(), instance staled!\n", __FUNCTION__); - up(&fsm->sem); - return -ESTALE; /* or better EPIPE? */ - } - - xmit_was_down = netif_queue_stopped(dev->netdev); - netif_stop_queue(dev->netdev); - atomic_set(&dev->enable_rx, 0); - - fsm->state = initial_state; - fsm->param = param; - fsm->result = 0; - - INIT_LIST_HEAD(&fsm->rq.lh_request); - fsm->rq.pending = 0; - fsm->rq.func = irda_config_fsm; - fsm->rq.data = dev; - - if (!irda_queue_request(&fsm->rq)) { /* returns 0 on error! */ - atomic_set(&dev->enable_rx, 1); - if (!xmit_was_down) - netif_wake_queue(dev->netdev); - up(&fsm->sem); - return -EAGAIN; - } - return 0; -} - -static int __init irda_thread_create(void) -{ - struct completion startup; - int pid; - - spin_lock_init(&irda_rq_queue.lock); - irda_rq_queue.thread = NULL; - INIT_LIST_HEAD(&irda_rq_queue.request_list); - init_waitqueue_head(&irda_rq_queue.kick); - init_waitqueue_head(&irda_rq_queue.done); - atomic_set(&irda_rq_queue.num_pending, 0); - - init_completion(&startup); - pid = kernel_thread(irda_thread, &startup, CLONE_FS|CLONE_FILES); - if (pid <= 0) - return -EAGAIN; - else - wait_for_completion(&startup); - - return 0; -} - -static void __exit irda_thread_join(void) -{ - if (irda_rq_queue.thread) { - flush_irda_queue(); - init_completion(&irda_rq_queue.exit); - irda_rq_queue.thread = NULL; - wake_up(&irda_rq_queue.kick); - wait_for_completion(&irda_rq_queue.exit); - } -} - -module_init(irda_thread_create); -module_exit(irda_thread_join); - -MODULE_AUTHOR("Martin Diehl <info@mdiehl.de>"); -MODULE_DESCRIPTION("IrDA SIR core"); -MODULE_LICENSE("GPL"); - diff --git a/drivers/net/irda/smsc-ircc2.c b/drivers/net/irda/smsc-ircc2.c index 58f76cefbc8..a4674044bd6 100644 --- a/drivers/net/irda/smsc-ircc2.c +++ b/drivers/net/irda/smsc-ircc2.c @@ -54,6 +54,7 @@ #include <linux/rtnetlink.h> #include <linux/serial_reg.h> #include <linux/dma-mapping.h> +#include <linux/pnp.h> #include <linux/platform_device.h> #include <asm/io.h> @@ -358,6 +359,16 @@ static inline void register_bank(int iobase, int bank) iobase + IRCC_MASTER); } +#ifdef CONFIG_PNP +/* PNP hotplug support */ +static const struct pnp_device_id smsc_ircc_pnp_table[] = { + { .id = "SMCf010", .driver_data = 0 }, + /* and presumably others */ + { } +}; +MODULE_DEVICE_TABLE(pnp, smsc_ircc_pnp_table); +#endif + /******************************************************************************* * @@ -2072,7 +2083,8 @@ static void smsc_ircc_sir_wait_hw_transmitter_finish(struct smsc_ircc_cb *self) /* PROBING * - * + * REVISIT we can be told about the device by PNP, and should use that info + * instead of probing hardware and creating a platform_device ... */ static int __init smsc_ircc_look_for_chips(void) diff --git a/drivers/net/mv643xx_eth.c b/drivers/net/mv643xx_eth.c index ea62a3e7d58..411f4d809c4 100644 --- a/drivers/net/mv643xx_eth.c +++ b/drivers/net/mv643xx_eth.c @@ -1419,6 +1419,8 @@ static int mv643xx_eth_probe(struct platform_device *pdev) mv643xx_eth_update_pscr(dev, &cmd); mv643xx_set_settings(dev, &cmd); + SET_MODULE_OWNER(dev); + SET_NETDEV_DEV(dev, &pdev->dev); err = register_netdev(dev); if (err) goto out; diff --git a/drivers/net/ne.c b/drivers/net/ne.c index 93c494bcd18..b32765215f7 100644 --- a/drivers/net/ne.c +++ b/drivers/net/ne.c @@ -139,8 +139,9 @@ bad_clone_list[] __initdata = { #if defined(CONFIG_PLAT_MAPPI) # define DCR_VAL 0x4b -#elif defined(CONFIG_PLAT_OAKS32R) -# define DCR_VAL 0x48 +#elif defined(CONFIG_PLAT_OAKS32R) || \ + defined(CONFIG_TOSHIBA_RBTX4927) || defined(CONFIG_TOSHIBA_RBTX4938) +# define DCR_VAL 0x48 /* 8-bit mode */ #else # define DCR_VAL 0x49 #endif @@ -396,10 +397,22 @@ static int __init ne_probe1(struct net_device *dev, int ioaddr) /* We must set the 8390 for word mode. */ outb_p(DCR_VAL, ioaddr + EN0_DCFG); start_page = NESM_START_PG; - stop_page = NESM_STOP_PG; + + /* + * Realtek RTL8019AS datasheet says that the PSTOP register + * shouldn't exceed 0x60 in 8-bit mode. + * This chip can be identified by reading the signature from + * the remote byte count registers (otherwise write-only)... + */ + if ((DCR_VAL & 0x01) == 0 && /* 8-bit mode */ + inb(ioaddr + EN0_RCNTLO) == 0x50 && + inb(ioaddr + EN0_RCNTHI) == 0x70) + stop_page = 0x60; + else + stop_page = NESM_STOP_PG; } else { start_page = NE1SM_START_PG; - stop_page = NE1SM_STOP_PG; + stop_page = NE1SM_STOP_PG; } #if defined(CONFIG_PLAT_MAPPI) || defined(CONFIG_PLAT_OAKS32R) @@ -509,15 +522,9 @@ static int __init ne_probe1(struct net_device *dev, int ioaddr) ei_status.name = name; ei_status.tx_start_page = start_page; ei_status.stop_page = stop_page; -#if defined(CONFIG_TOSHIBA_RBTX4927) || defined(CONFIG_TOSHIBA_RBTX4938) - wordlength = 1; -#endif -#ifdef CONFIG_PLAT_OAKS32R - ei_status.word16 = 0; -#else - ei_status.word16 = (wordlength == 2); -#endif + /* Use 16-bit mode only if this wasn't overridden by DCR_VAL */ + ei_status.word16 = (wordlength == 2 && (DCR_VAL & 0x01)); ei_status.rx_start_page = start_page + TX_PAGES; #ifdef PACKETBUF_MEMSIZE diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c index 459443b572c..1b236bdf6b9 100644 --- a/drivers/net/phy/mdio_bus.c +++ b/drivers/net/phy/mdio_bus.c @@ -60,8 +60,10 @@ int mdiobus_register(struct mii_bus *bus) for (i = 0; i < PHY_MAX_ADDR; i++) { struct phy_device *phydev; - if (bus->phy_mask & (1 << i)) + if (bus->phy_mask & (1 << i)) { + bus->phy_map[i] = NULL; continue; + } phydev = get_phy_device(bus, i); diff --git a/drivers/net/sis900.c b/drivers/net/sis900.c index b82191d2bee..f5a3bf4d959 100644 --- a/drivers/net/sis900.c +++ b/drivers/net/sis900.c @@ -127,6 +127,7 @@ static const struct mii_chip_info { } mii_chip_table[] = { { "SiS 900 Internal MII PHY", 0x001d, 0x8000, LAN }, { "SiS 7014 Physical Layer Solution", 0x0016, 0xf830, LAN }, + { "SiS 900 on Foxconn 661 7MI", 0x0143, 0xBC70, LAN }, { "Altimata AC101LF PHY", 0x0022, 0x5520, LAN }, { "ADM 7001 LAN PHY", 0x002e, 0xcc60, LAN }, { "AMD 79C901 10BASE-T PHY", 0x0000, 0x6B70, LAN }, diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 227df9876a2..ffd267fab21 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -51,7 +51,7 @@ #include "sky2.h" #define DRV_NAME "sky2" -#define DRV_VERSION "1.2" +#define DRV_VERSION "1.3" #define PFX DRV_NAME " " /* @@ -79,6 +79,8 @@ #define NAPI_WEIGHT 64 #define PHY_RETRIES 1000 +#define RING_NEXT(x,s) (((x)+1) & ((s)-1)) + static const u32 default_msg = NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK | NETIF_MSG_TIMER | NETIF_MSG_TX_ERR | NETIF_MSG_RX_ERR @@ -96,6 +98,10 @@ static int disable_msi = 0; module_param(disable_msi, int, 0); MODULE_PARM_DESC(disable_msi, "Disable Message Signaled Interrupt (MSI)"); +static int idle_timeout = 100; +module_param(idle_timeout, int, 0); +MODULE_PARM_DESC(idle_timeout, "Idle timeout workaround for lost interrupts (ms)"); + static const struct pci_device_id sky2_id_table[] = { { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) }, { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) }, @@ -122,6 +128,7 @@ MODULE_DEVICE_TABLE(pci, sky2_id_table); /* Avoid conditionals by using array */ static const unsigned txqaddr[] = { Q_XA1, Q_XA2 }; static const unsigned rxqaddr[] = { Q_R1, Q_R2 }; +static const u32 portirq_msk[] = { Y2_IS_PORT_1, Y2_IS_PORT_2 }; /* This driver supports yukon2 chipset only */ static const char *yukon2_name[] = { @@ -298,7 +305,8 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) struct sky2_port *sky2 = netdev_priv(hw->dev[port]); u16 ctrl, ct1000, adv, pg, ledctrl, ledover; - if (sky2->autoneg == AUTONEG_ENABLE && hw->chip_id != CHIP_ID_YUKON_XL) { + if (sky2->autoneg == AUTONEG_ENABLE && + (hw->chip_id != CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)) { u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL); ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK | @@ -326,7 +334,7 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO); if (sky2->autoneg == AUTONEG_ENABLE && - hw->chip_id == CHIP_ID_YUKON_XL) { + (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)) { ctrl &= ~PHY_M_PC_DSC_MSK; ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA; } @@ -442,10 +450,11 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3); /* set LED Function Control register */ - gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */ - PHY_M_LEDC_INIT_CTRL(7) | /* 10 Mbps */ - PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */ - PHY_M_LEDC_STA0_CTRL(7))); /* 1000 Mbps */ + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, + (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */ + PHY_M_LEDC_INIT_CTRL(7) | /* 10 Mbps */ + PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */ + PHY_M_LEDC_STA0_CTRL(7))); /* 1000 Mbps */ /* set Polarity Control register */ gm_phy_write(hw, port, PHY_MARV_PHY_STAT, @@ -459,6 +468,25 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) /* restore page register */ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); break; + case CHIP_ID_YUKON_EC_U: + pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); + + /* select page 3 to access LED control register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3); + + /* set LED Function Control register */ + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, + (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */ + PHY_M_LEDC_INIT_CTRL(8) | /* 10 Mbps */ + PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */ + PHY_M_LEDC_STA0_CTRL(7)));/* 1000 Mbps */ + + /* set Blink Rate in LED Timer Control Register */ + gm_phy_write(hw, port, PHY_MARV_INT_MASK, + ledctrl | PHY_M_LED_BLINK_RT(BLINK_84MS)); + /* restore page register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); + break; default: /* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */ @@ -467,19 +495,21 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) ledover |= PHY_M_LED_MO_RX(MO_LED_OFF); } - if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) { + if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev == CHIP_REV_YU_EC_A1) { /* apply fixes in PHY AFE */ - gm_phy_write(hw, port, 22, 255); + pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 255); + /* increase differential signal amplitude in 10BASE-T */ - gm_phy_write(hw, port, 24, 0xaa99); - gm_phy_write(hw, port, 23, 0x2011); + gm_phy_write(hw, port, 0x18, 0xaa99); + gm_phy_write(hw, port, 0x17, 0x2011); /* fix for IEEE A/B Symmetry failure in 1000BASE-T */ - gm_phy_write(hw, port, 24, 0xa204); - gm_phy_write(hw, port, 23, 0x2002); + gm_phy_write(hw, port, 0x18, 0xa204); + gm_phy_write(hw, port, 0x17, 0x2002); /* set page register to 0 */ - gm_phy_write(hw, port, 22, 0); + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); } else { gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl); @@ -553,6 +583,11 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port) if (sky2->duplex == DUPLEX_FULL) reg |= GM_GPCR_DUP_FULL; + + /* turn off pause in 10/100mbps half duplex */ + else if (sky2->speed != SPEED_1000 && + hw->chip_id != CHIP_ID_YUKON_EC_U) + sky2->tx_pause = sky2->rx_pause = 0; } else reg = GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100 | GM_GPCR_DUP_FULL; @@ -719,7 +754,7 @@ static inline struct sky2_tx_le *get_tx_le(struct sky2_port *sky2) { struct sky2_tx_le *le = sky2->tx_le + sky2->tx_prod; - sky2->tx_prod = (sky2->tx_prod + 1) % TX_RING_SIZE; + sky2->tx_prod = RING_NEXT(sky2->tx_prod, TX_RING_SIZE); return le; } @@ -735,7 +770,7 @@ static inline void sky2_put_idx(struct sky2_hw *hw, unsigned q, u16 idx) static inline struct sky2_rx_le *sky2_next_rx(struct sky2_port *sky2) { struct sky2_rx_le *le = sky2->rx_le + sky2->rx_put; - sky2->rx_put = (sky2->rx_put + 1) % RX_LE_SIZE; + sky2->rx_put = RING_NEXT(sky2->rx_put, RX_LE_SIZE); return le; } @@ -1050,7 +1085,7 @@ static int sky2_up(struct net_device *dev) /* Enable interrupts from phy/mac for port */ imask = sky2_read32(hw, B0_IMSK); - imask |= (port == 0) ? Y2_IS_PORT_1 : Y2_IS_PORT_2; + imask |= portirq_msk[port]; sky2_write32(hw, B0_IMSK, imask); return 0; @@ -1078,7 +1113,7 @@ err_out: /* Modular subtraction in ring */ static inline int tx_dist(unsigned tail, unsigned head) { - return (head - tail) % TX_RING_SIZE; + return (head - tail) & (TX_RING_SIZE - 1); } /* Number of list elements available for next tx */ @@ -1255,7 +1290,7 @@ static int sky2_xmit_frame(struct sk_buff *skb, struct net_device *dev) le->opcode = OP_BUFFER | HW_OWNER; fre = sky2->tx_ring - + ((re - sky2->tx_ring) + i + 1) % TX_RING_SIZE; + + RING_NEXT((re - sky2->tx_ring) + i, TX_RING_SIZE); pci_unmap_addr_set(fre, mapaddr, mapping); } @@ -1315,7 +1350,7 @@ static void sky2_tx_complete(struct sky2_port *sky2, u16 done) for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) { struct tx_ring_info *fre; - fre = sky2->tx_ring + (put + i + 1) % TX_RING_SIZE; + fre = sky2->tx_ring + RING_NEXT(put + i, TX_RING_SIZE); pci_unmap_page(pdev, pci_unmap_addr(fre, mapaddr), skb_shinfo(skb)->frags[i].size, PCI_DMA_TODEVICE); @@ -1401,7 +1436,7 @@ static int sky2_down(struct net_device *dev) /* Disable port IRQ */ imask = sky2_read32(hw, B0_IMSK); - imask &= ~(sky2->port == 0) ? Y2_IS_PORT_1 : Y2_IS_PORT_2; + imask &= ~portirq_msk[port]; sky2_write32(hw, B0_IMSK, imask); /* turn off LED's */ @@ -1498,17 +1533,26 @@ static void sky2_link_up(struct sky2_port *sky2) sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_ON | LINKLED_BLINK_OFF | LINKLED_LINKSYNC_OFF); - if (hw->chip_id == CHIP_ID_YUKON_XL) { + if (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U) { u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); + u16 led = PHY_M_LEDC_LOS_CTRL(1); /* link active */ + + switch(sky2->speed) { + case SPEED_10: + led |= PHY_M_LEDC_INIT_CTRL(7); + break; + + case SPEED_100: + led |= PHY_M_LEDC_STA1_CTRL(7); + break; + + case SPEED_1000: + led |= PHY_M_LEDC_STA0_CTRL(7); + break; + } gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3); - gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */ - PHY_M_LEDC_INIT_CTRL(sky2->speed == - SPEED_10 ? 7 : 0) | - PHY_M_LEDC_STA1_CTRL(sky2->speed == - SPEED_100 ? 7 : 0) | - PHY_M_LEDC_STA0_CTRL(sky2->speed == - SPEED_1000 ? 7 : 0)); + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, led); gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); } @@ -1583,7 +1627,7 @@ static int sky2_autoneg_done(struct sky2_port *sky2, u16 aux) sky2->speed = sky2_phy_speed(hw, aux); /* Pause bits are offset (9..8) */ - if (hw->chip_id == CHIP_ID_YUKON_XL) + if (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U) aux >>= 6; sky2->rx_pause = (aux & PHY_M_PS_RX_P_EN) != 0; @@ -1859,35 +1903,28 @@ static inline void sky2_tx_done(struct net_device *dev, u16 last) static int sky2_status_intr(struct sky2_hw *hw, int to_do) { int work_done = 0; + u16 hwidx = sky2_read16(hw, STAT_PUT_IDX); rmb(); - for(;;) { + while (hw->st_idx != hwidx) { struct sky2_status_le *le = hw->st_le + hw->st_idx; struct net_device *dev; struct sky2_port *sky2; struct sk_buff *skb; u32 status; u16 length; - u8 link, opcode; - opcode = le->opcode; - if (!opcode) - break; - opcode &= ~HW_OWNER; - - hw->st_idx = (hw->st_idx + 1) % STATUS_RING_SIZE; - le->opcode = 0; + hw->st_idx = RING_NEXT(hw->st_idx, STATUS_RING_SIZE); - link = le->link; - BUG_ON(link >= 2); - dev = hw->dev[link]; + BUG_ON(le->link >= 2); + dev = hw->dev[le->link]; sky2 = netdev_priv(dev); length = le->length; status = le->status; - switch (opcode) { + switch (le->opcode & ~HW_OWNER) { case OP_RXSTAT: skb = sky2_receive(sky2, length, status); if (!skb) @@ -1927,7 +1964,8 @@ static int sky2_status_intr(struct sky2_hw *hw, int to_do) case OP_TXINDEXLE: /* TX index reports status for both ports */ - sky2_tx_done(hw->dev[0], status & 0xffff); + BUILD_BUG_ON(TX_RING_SIZE > 0x1000); + sky2_tx_done(hw->dev[0], status & 0xfff); if (hw->dev[1]) sky2_tx_done(hw->dev[1], ((status >> 24) & 0xff) @@ -1937,8 +1975,8 @@ static int sky2_status_intr(struct sky2_hw *hw, int to_do) default: if (net_ratelimit()) printk(KERN_WARNING PFX - "unknown status opcode 0x%x\n", opcode); - break; + "unknown status opcode 0x%x\n", le->opcode); + goto exit_loop; } } @@ -2089,12 +2127,13 @@ static void sky2_descriptor_error(struct sky2_hw *hw, unsigned port, */ static void sky2_idle(unsigned long arg) { - struct net_device *dev = (struct net_device *) arg; + struct sky2_hw *hw = (struct sky2_hw *) arg; + struct net_device *dev = hw->dev[0]; - local_irq_disable(); if (__netif_rx_schedule_prep(dev)) __netif_rx_schedule(dev); - local_irq_enable(); + + mod_timer(&hw->idle_timer, jiffies + msecs_to_jiffies(idle_timeout)); } @@ -2105,65 +2144,46 @@ static int sky2_poll(struct net_device *dev0, int *budget) int work_done = 0; u32 status = sky2_read32(hw, B0_Y2_SP_EISR); - restart_poll: - if (unlikely(status & ~Y2_IS_STAT_BMU)) { - if (status & Y2_IS_HW_ERR) - sky2_hw_intr(hw); - - if (status & Y2_IS_IRQ_PHY1) - sky2_phy_intr(hw, 0); - - if (status & Y2_IS_IRQ_PHY2) - sky2_phy_intr(hw, 1); + if (status & Y2_IS_HW_ERR) + sky2_hw_intr(hw); - if (status & Y2_IS_IRQ_MAC1) - sky2_mac_intr(hw, 0); + if (status & Y2_IS_IRQ_PHY1) + sky2_phy_intr(hw, 0); - if (status & Y2_IS_IRQ_MAC2) - sky2_mac_intr(hw, 1); + if (status & Y2_IS_IRQ_PHY2) + sky2_phy_intr(hw, 1); - if (status & Y2_IS_CHK_RX1) - sky2_descriptor_error(hw, 0, "receive", Y2_IS_CHK_RX1); + if (status & Y2_IS_IRQ_MAC1) + sky2_mac_intr(hw, 0); - if (status & Y2_IS_CHK_RX2) - sky2_descriptor_error(hw, 1, "receive", Y2_IS_CHK_RX2); + if (status & Y2_IS_IRQ_MAC2) + sky2_mac_intr(hw, 1); - if (status & Y2_IS_CHK_TXA1) - sky2_descriptor_error(hw, 0, "transmit", Y2_IS_CHK_TXA1); + if (status & Y2_IS_CHK_RX1) + sky2_descriptor_error(hw, 0, "receive", Y2_IS_CHK_RX1); - if (status & Y2_IS_CHK_TXA2) - sky2_descriptor_error(hw, 1, "transmit", Y2_IS_CHK_TXA2); - } + if (status & Y2_IS_CHK_RX2) + sky2_descriptor_error(hw, 1, "receive", Y2_IS_CHK_RX2); - if (status & Y2_IS_STAT_BMU) { - work_done += sky2_status_intr(hw, work_limit - work_done); - *budget -= work_done; - dev0->quota -= work_done; + if (status & Y2_IS_CHK_TXA1) + sky2_descriptor_error(hw, 0, "transmit", Y2_IS_CHK_TXA1); - if (work_done >= work_limit) - return 1; + if (status & Y2_IS_CHK_TXA2) + sky2_descriptor_error(hw, 1, "transmit", Y2_IS_CHK_TXA2); + if (status & Y2_IS_STAT_BMU) sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ); - } - - mod_timer(&hw->idle_timer, jiffies + HZ); - local_irq_disable(); - __netif_rx_complete(dev0); + work_done = sky2_status_intr(hw, work_limit); + *budget -= work_done; + dev0->quota -= work_done; - status = sky2_read32(hw, B0_Y2_SP_LISR); + if (work_done >= work_limit) + return 1; - if (unlikely(status)) { - /* More work pending, try and keep going */ - if (__netif_rx_schedule_prep(dev0)) { - __netif_rx_reschedule(dev0, work_done); - status = sky2_read32(hw, B0_Y2_SP_EISR); - local_irq_enable(); - goto restart_poll; - } - } + netif_rx_complete(dev0); - local_irq_enable(); + status = sky2_read32(hw, B0_Y2_SP_LISR); return 0; } @@ -2244,13 +2264,6 @@ static int __devinit sky2_reset(struct sky2_hw *hw) return -EOPNOTSUPP; } - /* This chip is new and not tested yet */ - if (hw->chip_id == CHIP_ID_YUKON_EC_U) { - pr_info(PFX "%s: is a version of Yukon 2 chipset that has not been tested yet.\n", - pci_name(hw->pdev)); - pr_info("Please report success/failure to maintainer <shemminger@osdl.org>\n"); - } - /* disable ASF */ if (hw->chip_id <= CHIP_ID_YUKON_EC) { sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET); @@ -3302,7 +3315,10 @@ static int __devinit sky2_probe(struct pci_dev *pdev, sky2_write32(hw, B0_IMSK, Y2_IS_BASE); - setup_timer(&hw->idle_timer, sky2_idle, (unsigned long) dev); + setup_timer(&hw->idle_timer, sky2_idle, (unsigned long) hw); + if (idle_timeout > 0) + mod_timer(&hw->idle_timer, + jiffies + msecs_to_jiffies(idle_timeout)); pci_set_drvdata(pdev, hw); @@ -3342,6 +3358,8 @@ static void __devexit sky2_remove(struct pci_dev *pdev) del_timer_sync(&hw->idle_timer); sky2_write32(hw, B0_IMSK, 0); + synchronize_irq(hw->pdev->irq); + dev0 = hw->dev[0]; dev1 = hw->dev[1]; if (dev1) diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index b026f5653f0..8012994c9b9 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -378,6 +378,9 @@ enum { CHIP_REV_YU_EC_A1 = 0, /* Chip Rev. for Yukon-EC A1/A0 */ CHIP_REV_YU_EC_A2 = 1, /* Chip Rev. for Yukon-EC A2 */ CHIP_REV_YU_EC_A3 = 2, /* Chip Rev. for Yukon-EC A3 */ + + CHIP_REV_YU_EC_U_A0 = 0, + CHIP_REV_YU_EC_U_A1 = 1, }; /* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */ diff --git a/drivers/net/spider_net.c b/drivers/net/spider_net.c index 43f5e86fc55..394339d5e87 100644 --- a/drivers/net/spider_net.c +++ b/drivers/net/spider_net.c @@ -1652,6 +1652,8 @@ spider_net_enable_card(struct spider_net_card *card) { SPIDER_NET_GFTRESTRT, SPIDER_NET_RESTART_VALUE }, { SPIDER_NET_GMRWOLCTRL, 0 }, + { SPIDER_NET_GTESTMD, 0x10000000 }, + { SPIDER_NET_GTTQMSK, 0x00400040 }, { SPIDER_NET_GTESTMD, 0 }, { SPIDER_NET_GMACINTEN, 0 }, @@ -1792,15 +1794,7 @@ spider_net_setup_phy(struct spider_net_card *card) if (phy->def->ops->setup_forced) phy->def->ops->setup_forced(phy, SPEED_1000, DUPLEX_FULL); - /* the following two writes could be moved to sungem_phy.c */ - /* enable fiber mode */ - spider_net_write_phy(card->netdev, 1, MII_NCONFIG, 0x9020); - /* LEDs active in both modes, autosense prio = fiber */ - spider_net_write_phy(card->netdev, 1, MII_NCONFIG, 0x945f); - - /* switch off fibre autoneg */ - spider_net_write_phy(card->netdev, 1, MII_NCONFIG, 0xfc01); - spider_net_write_phy(card->netdev, 1, 0x0b, 0x0004); + phy->def->ops->enable_fiber(phy); phy->def->ops->read_link(phy); pr_info("Found %s with %i Mbps, %s-duplex.\n", phy->def->name, diff --git a/drivers/net/spider_net.h b/drivers/net/spider_net.h index 5922b529a04..3b8d951cf73 100644 --- a/drivers/net/spider_net.h +++ b/drivers/net/spider_net.h @@ -120,6 +120,8 @@ extern char spider_net_driver_name[]; #define SPIDER_NET_GMRUAFILnR 0x00000500 #define SPIDER_NET_GMRUA0FIL15R 0x00000578 +#define SPIDER_NET_GTTQMSK 0x00000934 + /* RX DMA controller registers, all 0x00000a.. are for DMA controller A, * 0x00000b.. for DMA controller B, etc. */ #define SPIDER_NET_GDADCHA 0x00000a00 diff --git a/drivers/net/sungem_phy.c b/drivers/net/sungem_phy.c index 046371ee5bb..b2ddd5e7930 100644 --- a/drivers/net/sungem_phy.c +++ b/drivers/net/sungem_phy.c @@ -329,6 +329,30 @@ static int bcm5421_init(struct mii_phy* phy) return 0; } +static int bcm5421_enable_fiber(struct mii_phy* phy) +{ + /* enable fiber mode */ + phy_write(phy, MII_NCONFIG, 0x9020); + /* LEDs active in both modes, autosense prio = fiber */ + phy_write(phy, MII_NCONFIG, 0x945f); + + /* switch off fibre autoneg */ + phy_write(phy, MII_NCONFIG, 0xfc01); + phy_write(phy, 0x0b, 0x0004); + + return 0; +} + +static int bcm5461_enable_fiber(struct mii_phy* phy) +{ + phy_write(phy, MII_NCONFIG, 0xfc0c); + phy_write(phy, MII_BMCR, 0x4140); + phy_write(phy, MII_NCONFIG, 0xfc0b); + phy_write(phy, MII_BMCR, 0x0140); + + return 0; +} + static int bcm54xx_setup_aneg(struct mii_phy *phy, u32 advertise) { u16 ctl, adv; @@ -762,6 +786,7 @@ static struct mii_phy_ops bcm5421_phy_ops = { .setup_forced = bcm54xx_setup_forced, .poll_link = genmii_poll_link, .read_link = bcm54xx_read_link, + .enable_fiber = bcm5421_enable_fiber, }; static struct mii_phy_def bcm5421_phy_def = { @@ -792,6 +817,25 @@ static struct mii_phy_def bcm5421k2_phy_def = { .ops = &bcm5421k2_phy_ops }; +static struct mii_phy_ops bcm5461_phy_ops = { + .init = bcm5421_init, + .suspend = generic_suspend, + .setup_aneg = bcm54xx_setup_aneg, + .setup_forced = bcm54xx_setup_forced, + .poll_link = genmii_poll_link, + .read_link = bcm54xx_read_link, + .enable_fiber = bcm5461_enable_fiber, +}; + +static struct mii_phy_def bcm5461_phy_def = { + .phy_id = 0x002060c0, + .phy_id_mask = 0xfffffff0, + .name = "BCM5461", + .features = MII_GBIT_FEATURES, + .magic_aneg = 1, + .ops = &bcm5461_phy_ops +}; + /* Broadcom BCM 5462 built-in Vesta */ static struct mii_phy_ops bcm5462V_phy_ops = { .init = bcm5421_init, @@ -857,6 +901,7 @@ static struct mii_phy_def* mii_phy_table[] = { &bcm5411_phy_def, &bcm5421_phy_def, &bcm5421k2_phy_def, + &bcm5461_phy_def, &bcm5462V_phy_def, &marvell_phy_def, &genmii_phy_def, diff --git a/drivers/net/sungem_phy.h b/drivers/net/sungem_phy.h index 430544496c5..69e125197fc 100644 --- a/drivers/net/sungem_phy.h +++ b/drivers/net/sungem_phy.h @@ -12,6 +12,7 @@ struct mii_phy_ops int (*setup_forced)(struct mii_phy *phy, int speed, int fd); int (*poll_link)(struct mii_phy *phy); int (*read_link)(struct mii_phy *phy); + int (*enable_fiber)(struct mii_phy *phy); }; /* Structure used to statically define an mii/gii based PHY */ diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c index 73e271e59c6..2bd9592b75c 100644 --- a/drivers/net/tg3.c +++ b/drivers/net/tg3.c @@ -69,8 +69,8 @@ #define DRV_MODULE_NAME "tg3" #define PFX DRV_MODULE_NAME ": " -#define DRV_MODULE_VERSION "3.56" -#define DRV_MODULE_RELDATE "Apr 1, 2006" +#define DRV_MODULE_VERSION "3.57" +#define DRV_MODULE_RELDATE "Apr 28, 2006" #define TG3_DEF_MAC_MODE 0 #define TG3_DEF_RX_MODE 0 @@ -974,6 +974,8 @@ static int tg3_phy_reset_5703_4_5(struct tg3 *tp) return err; } +static void tg3_link_report(struct tg3 *); + /* This will reset the tigon3 PHY if there is no valid * link unless the FORCE argument is non-zero. */ @@ -987,6 +989,11 @@ static int tg3_phy_reset(struct tg3 *tp) if (err != 0) return -EBUSY; + if (netif_running(tp->dev) && netif_carrier_ok(tp->dev)) { + netif_carrier_off(tp->dev); + tg3_link_report(tp); + } + if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5703 || GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5704 || GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5705) { @@ -1023,6 +1030,12 @@ out: tg3_writephy(tp, MII_TG3_DSP_RW_PORT, 0x14e2); tg3_writephy(tp, MII_TG3_AUX_CTRL, 0x0400); } + else if (tp->tg3_flags2 & TG3_FLG2_PHY_JITTER_BUG) { + tg3_writephy(tp, MII_TG3_AUX_CTRL, 0x0c00); + tg3_writephy(tp, MII_TG3_DSP_ADDRESS, 0x000a); + tg3_writephy(tp, MII_TG3_DSP_RW_PORT, 0x010b); + tg3_writephy(tp, MII_TG3_AUX_CTRL, 0x0400); + } /* Set Extended packet length bit (bit 14) on all chips that */ /* support jumbo frames */ if ((tp->phy_id & PHY_ID_MASK) == PHY_ID_BCM5401) { @@ -3531,7 +3544,7 @@ static irqreturn_t tg3_test_isr(int irq, void *dev_id, return IRQ_RETVAL(0); } -static int tg3_init_hw(struct tg3 *); +static int tg3_init_hw(struct tg3 *, int); static int tg3_halt(struct tg3 *, int, int); #ifdef CONFIG_NET_POLL_CONTROLLER @@ -3567,7 +3580,7 @@ static void tg3_reset_task(void *_data) tp->tg3_flags2 &= ~TG3_FLG2_RESTART_TIMER; tg3_halt(tp, RESET_KIND_SHUTDOWN, 0); - tg3_init_hw(tp); + tg3_init_hw(tp, 1); tg3_netif_start(tp); @@ -4042,7 +4055,7 @@ static int tg3_change_mtu(struct net_device *dev, int new_mtu) tg3_set_mtu(dev, tp, new_mtu); - tg3_init_hw(tp); + tg3_init_hw(tp, 0); tg3_netif_start(tp); @@ -5719,9 +5732,23 @@ static int tg3_set_mac_addr(struct net_device *dev, void *p) if (!netif_running(dev)) return 0; - spin_lock_bh(&tp->lock); - __tg3_set_mac_addr(tp); - spin_unlock_bh(&tp->lock); + if (tp->tg3_flags & TG3_FLAG_ENABLE_ASF) { + /* Reset chip so that ASF can re-init any MAC addresses it + * needs. + */ + tg3_netif_stop(tp); + tg3_full_lock(tp, 1); + + tg3_halt(tp, RESET_KIND_SHUTDOWN, 1); + tg3_init_hw(tp, 0); + + tg3_netif_start(tp); + tg3_full_unlock(tp); + } else { + spin_lock_bh(&tp->lock); + __tg3_set_mac_addr(tp); + spin_unlock_bh(&tp->lock); + } return 0; } @@ -5771,7 +5798,7 @@ static void __tg3_set_coalesce(struct tg3 *tp, struct ethtool_coalesce *ec) } /* tp->lock is held. */ -static int tg3_reset_hw(struct tg3 *tp) +static int tg3_reset_hw(struct tg3 *tp, int reset_phy) { u32 val, rdmac_mode; int i, err, limit; @@ -5786,7 +5813,7 @@ static int tg3_reset_hw(struct tg3 *tp) tg3_abort_hw(tp, 1); } - if (tp->tg3_flags2 & TG3_FLG2_MII_SERDES) + if ((tp->tg3_flags2 & TG3_FLG2_MII_SERDES) && reset_phy) tg3_phy_reset(tp); err = tg3_chip_reset(tp); @@ -6327,7 +6354,7 @@ static int tg3_reset_hw(struct tg3 *tp) tw32(GRC_LOCAL_CTRL, tp->grc_local_ctrl); } - err = tg3_setup_phy(tp, 1); + err = tg3_setup_phy(tp, reset_phy); if (err) return err; @@ -6400,7 +6427,7 @@ static int tg3_reset_hw(struct tg3 *tp) /* Called at device open time to get the chip ready for * packet processing. Invoked with tp->lock held. */ -static int tg3_init_hw(struct tg3 *tp) +static int tg3_init_hw(struct tg3 *tp, int reset_phy) { int err; @@ -6413,7 +6440,7 @@ static int tg3_init_hw(struct tg3 *tp) tw32(TG3PCI_MEM_WIN_BASE_ADDR, 0); - err = tg3_reset_hw(tp); + err = tg3_reset_hw(tp, reset_phy); out: return err; @@ -6683,7 +6710,7 @@ static int tg3_test_msi(struct tg3 *tp) tg3_full_lock(tp, 1); tg3_halt(tp, RESET_KIND_SHUTDOWN, 1); - err = tg3_init_hw(tp); + err = tg3_init_hw(tp, 1); tg3_full_unlock(tp); @@ -6748,7 +6775,7 @@ static int tg3_open(struct net_device *dev) tg3_full_lock(tp, 0); - err = tg3_init_hw(tp); + err = tg3_init_hw(tp, 1); if (err) { tg3_halt(tp, RESET_KIND_SHUTDOWN, 1); tg3_free_rings(tp); @@ -7839,7 +7866,7 @@ static int tg3_set_ringparam(struct net_device *dev, struct ethtool_ringparam *e if (netif_running(dev)) { tg3_halt(tp, RESET_KIND_SHUTDOWN, 1); - tg3_init_hw(tp); + tg3_init_hw(tp, 1); tg3_netif_start(tp); } @@ -7884,7 +7911,7 @@ static int tg3_set_pauseparam(struct net_device *dev, struct ethtool_pauseparam if (netif_running(dev)) { tg3_halt(tp, RESET_KIND_SHUTDOWN, 1); - tg3_init_hw(tp); + tg3_init_hw(tp, 1); tg3_netif_start(tp); } @@ -8427,6 +8454,9 @@ static int tg3_run_loopback(struct tg3 *tp, int loopback_mode) tx_len = 1514; skb = dev_alloc_skb(tx_len); + if (!skb) + return -ENOMEM; + tx_data = skb_put(skb, tx_len); memcpy(tx_data, tp->dev->dev_addr, 6); memset(tx_data + 6, 0x0, 8); @@ -8522,7 +8552,7 @@ static int tg3_test_loopback(struct tg3 *tp) if (!netif_running(tp->dev)) return TG3_LOOPBACK_FAILED; - tg3_reset_hw(tp); + tg3_reset_hw(tp, 1); if (tg3_run_loopback(tp, TG3_MAC_LOOPBACK)) err |= TG3_MAC_LOOPBACK_FAILED; @@ -8596,7 +8626,7 @@ static void tg3_self_test(struct net_device *dev, struct ethtool_test *etest, tg3_halt(tp, RESET_KIND_SHUTDOWN, 1); if (netif_running(dev)) { tp->tg3_flags |= TG3_FLAG_INIT_COMPLETE; - tg3_init_hw(tp); + tg3_init_hw(tp, 1); tg3_netif_start(tp); } @@ -9377,7 +9407,7 @@ static int tg3_nvram_write_block_buffered(struct tg3 *tp, u32 offset, u32 len, if ((page_off == 0) || (i == 0)) nvram_cmd |= NVRAM_CMD_FIRST; - else if (page_off == (tp->nvram_pagesize - 4)) + if (page_off == (tp->nvram_pagesize - 4)) nvram_cmd |= NVRAM_CMD_LAST; if (i == (len - 4)) @@ -10353,10 +10383,13 @@ static int __devinit tg3_get_invariants(struct tg3 *tp) if (tp->pci_chip_rev_id == CHIPREV_ID_5704_A0) tp->tg3_flags2 |= TG3_FLG2_PHY_5704_A0_BUG; - if ((tp->tg3_flags2 & TG3_FLG2_5705_PLUS) && - (GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5755) && - (GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5787)) - tp->tg3_flags2 |= TG3_FLG2_PHY_BER_BUG; + if (tp->tg3_flags2 & TG3_FLG2_5705_PLUS) { + if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5755 || + GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5787) + tp->tg3_flags2 |= TG3_FLG2_PHY_JITTER_BUG; + else + tp->tg3_flags2 |= TG3_FLG2_PHY_BER_BUG; + } tp->coalesce_mode = 0; if (GET_CHIP_REV(tp->pci_chip_rev_id) != CHIPREV_5700_AX && @@ -11569,7 +11602,7 @@ static int tg3_suspend(struct pci_dev *pdev, pm_message_t state) tg3_full_lock(tp, 0); tp->tg3_flags |= TG3_FLAG_INIT_COMPLETE; - tg3_init_hw(tp); + tg3_init_hw(tp, 1); tp->timer.expires = jiffies + tp->timer_offset; add_timer(&tp->timer); @@ -11603,7 +11636,7 @@ static int tg3_resume(struct pci_dev *pdev) tg3_full_lock(tp, 0); tp->tg3_flags |= TG3_FLAG_INIT_COMPLETE; - tg3_init_hw(tp); + tg3_init_hw(tp, 1); tp->timer.expires = jiffies + tp->timer_offset; add_timer(&tp->timer); diff --git a/drivers/net/tg3.h b/drivers/net/tg3.h index 8c8b987d125..0e29b885d44 100644 --- a/drivers/net/tg3.h +++ b/drivers/net/tg3.h @@ -2215,6 +2215,7 @@ struct tg3 { #define TG3_FLG2_HW_TSO_2 0x08000000 #define TG3_FLG2_HW_TSO (TG3_FLG2_HW_TSO_1 | TG3_FLG2_HW_TSO_2) #define TG3_FLG2_1SHOT_MSI 0x10000000 +#define TG3_FLG2_PHY_JITTER_BUG 0x20000000 u32 split_mode_max_reqs; #define SPLIT_MODE_5704_MAX_REQ 3 diff --git a/drivers/net/via-rhine.c b/drivers/net/via-rhine.c index 6a23964c131..a6dc53b4250 100644 --- a/drivers/net/via-rhine.c +++ b/drivers/net/via-rhine.c @@ -129,6 +129,7 @@ - Massive clean-up - Rewrite PHY, media handling (remove options, full_duplex, backoff) - Fix Tx engine race for good + - Craig Brind: Zero padded aligned buffers for short packets. */ @@ -1326,7 +1327,12 @@ static int rhine_start_tx(struct sk_buff *skb, struct net_device *dev) rp->stats.tx_dropped++; return 0; } + + /* Padding is not copied and so must be redone. */ skb_copy_and_csum_dev(skb, rp->tx_buf[entry]); + if (skb->len < ETH_ZLEN) + memset(rp->tx_buf[entry] + skb->len, 0, + ETH_ZLEN - skb->len); rp->tx_skbuff_dma[entry] = 0; rp->tx_ring[entry].addr = cpu_to_le32(rp->tx_bufs_dma + (rp->tx_buf[entry] - diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_main.c b/drivers/net/wireless/bcm43xx/bcm43xx_main.c index 9a06e61df0a..e2982a83ae4 100644 --- a/drivers/net/wireless/bcm43xx/bcm43xx_main.c +++ b/drivers/net/wireless/bcm43xx/bcm43xx_main.c @@ -939,9 +939,9 @@ static int bcm43xx_sprom_extract(struct bcm43xx_private *bcm) return 0; } -static void bcm43xx_geo_init(struct bcm43xx_private *bcm) +static int bcm43xx_geo_init(struct bcm43xx_private *bcm) { - struct ieee80211_geo geo; + struct ieee80211_geo *geo; struct ieee80211_channel *chan; int have_a = 0, have_bg = 0; int i; @@ -949,7 +949,10 @@ static void bcm43xx_geo_init(struct bcm43xx_private *bcm) struct bcm43xx_phyinfo *phy; const char *iso_country; - memset(&geo, 0, sizeof(geo)); + geo = kzalloc(sizeof(*geo), GFP_KERNEL); + if (!geo) + return -ENOMEM; + for (i = 0; i < bcm->nr_80211_available; i++) { phy = &(bcm->core_80211_ext[i].phy); switch (phy->type) { @@ -967,31 +970,36 @@ static void bcm43xx_geo_init(struct bcm43xx_private *bcm) iso_country = bcm43xx_locale_iso(bcm->sprom.locale); if (have_a) { - for (i = 0, channel = 0; channel < 201; channel++) { - chan = &geo.a[i++]; + for (i = 0, channel = IEEE80211_52GHZ_MIN_CHANNEL; + channel <= IEEE80211_52GHZ_MAX_CHANNEL; channel++) { + chan = &geo->a[i++]; chan->freq = bcm43xx_channel_to_freq_a(channel); chan->channel = channel; } - geo.a_channels = i; + geo->a_channels = i; } if (have_bg) { - for (i = 0, channel = 1; channel < 15; channel++) { - chan = &geo.bg[i++]; + for (i = 0, channel = IEEE80211_24GHZ_MIN_CHANNEL; + channel <= IEEE80211_24GHZ_MAX_CHANNEL; channel++) { + chan = &geo->bg[i++]; chan->freq = bcm43xx_channel_to_freq_bg(channel); chan->channel = channel; } - geo.bg_channels = i; + geo->bg_channels = i; } - memcpy(geo.name, iso_country, 2); + memcpy(geo->name, iso_country, 2); if (0 /*TODO: Outdoor use only */) - geo.name[2] = 'O'; + geo->name[2] = 'O'; else if (0 /*TODO: Indoor use only */) - geo.name[2] = 'I'; + geo->name[2] = 'I'; else - geo.name[2] = ' '; - geo.name[3] = '\0'; + geo->name[2] = ' '; + geo->name[3] = '\0'; + + ieee80211_set_geo(bcm->ieee, geo); + kfree(geo); - ieee80211_set_geo(bcm->ieee, &geo); + return 0; } /* DummyTransmission function, as documented on @@ -3479,16 +3487,17 @@ static int bcm43xx_attach_board(struct bcm43xx_private *bcm) goto err_80211_unwind; bcm43xx_wireless_core_disable(bcm); } + err = bcm43xx_geo_init(bcm); + if (err) + goto err_80211_unwind; bcm43xx_pctl_set_crystal(bcm, 0); /* Set the MAC address in the networking subsystem */ - if (bcm43xx_current_phy(bcm)->type == BCM43xx_PHYTYPE_A) + if (is_valid_ether_addr(bcm->sprom.et1macaddr)) memcpy(bcm->net_dev->dev_addr, bcm->sprom.et1macaddr, 6); else memcpy(bcm->net_dev->dev_addr, bcm->sprom.il0macaddr, 6); - bcm43xx_geo_init(bcm); - snprintf(bcm->nick, IW_ESSID_MAX_SIZE, "Broadcom %04X", bcm->chip_id); diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_main.h b/drivers/net/wireless/bcm43xx/bcm43xx_main.h index eca79a38594..30a202b258b 100644 --- a/drivers/net/wireless/bcm43xx/bcm43xx_main.h +++ b/drivers/net/wireless/bcm43xx/bcm43xx_main.h @@ -118,12 +118,14 @@ int bcm43xx_channel_to_freq(struct bcm43xx_private *bcm, static inline int bcm43xx_is_valid_channel_a(u8 channel) { - return (channel <= 200); + return (channel >= IEEE80211_52GHZ_MIN_CHANNEL + && channel <= IEEE80211_52GHZ_MAX_CHANNEL); } static inline int bcm43xx_is_valid_channel_bg(u8 channel) { - return (channel >= 1 && channel <= 14); + return (channel >= IEEE80211_24GHZ_MIN_CHANNEL + && channel <= IEEE80211_24GHZ_MAX_CHANNEL); } static inline int bcm43xx_is_valid_channel(struct bcm43xx_private *bcm, diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_phy.c b/drivers/net/wireless/bcm43xx/bcm43xx_phy.c index 33137165727..b0abac51553 100644 --- a/drivers/net/wireless/bcm43xx/bcm43xx_phy.c +++ b/drivers/net/wireless/bcm43xx/bcm43xx_phy.c @@ -1287,7 +1287,7 @@ static void bcm43xx_phy_initg(struct bcm43xx_private *bcm) if (radio->revision == 8) bcm43xx_phy_write(bcm, 0x0805, 0x3230); bcm43xx_phy_init_pctl(bcm); - if (bcm->chip_id == 0x4306 && bcm->chip_package != 2) { + if (bcm->chip_id == 0x4306 && bcm->chip_package == 2) { bcm43xx_phy_write(bcm, 0x0429, bcm43xx_phy_read(bcm, 0x0429) & 0xBFFF); bcm43xx_phy_write(bcm, 0x04C3, diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_wx.c b/drivers/net/wireless/bcm43xx/bcm43xx_wx.c index 3edbb481a0a..b45063974ae 100644 --- a/drivers/net/wireless/bcm43xx/bcm43xx_wx.c +++ b/drivers/net/wireless/bcm43xx/bcm43xx_wx.c @@ -182,8 +182,11 @@ static int bcm43xx_wx_set_mode(struct net_device *net_dev, mode = BCM43xx_INITIAL_IWMODE; bcm43xx_lock_mmio(bcm, flags); - if (bcm->ieee->iw_mode != mode) - bcm43xx_set_iwmode(bcm, mode); + if (bcm->initialized) { + if (bcm->ieee->iw_mode != mode) + bcm43xx_set_iwmode(bcm, mode); + } else + bcm->ieee->iw_mode = mode; bcm43xx_unlock_mmio(bcm, flags); return 0; diff --git a/drivers/pci/msi.c b/drivers/pci/msi.c index 2087a397ef1..9855c4c920b 100644 --- a/drivers/pci/msi.c +++ b/drivers/pci/msi.c @@ -793,8 +793,10 @@ static int msix_capability_init(struct pci_dev *dev, if (!entry) break; vector = get_msi_vector(dev); - if (vector < 0) + if (vector < 0) { + kmem_cache_free(msi_cachep, entry); break; + } j = entries[i].entry; entries[i].vector = vector; diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index c42ae2cf8d6..19e2b174d33 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -642,13 +642,15 @@ static void quirk_via_irq(struct pci_dev *dev) new_irq = dev->irq & 0xf; pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq); if (new_irq != irq) { - printk(KERN_INFO "PCI: Via IRQ fixup for %s, from %d to %d\n", + printk(KERN_INFO "PCI: VIA IRQ fixup for %s, from %d to %d\n", pci_name(dev), irq, new_irq); udelay(15); /* unknown if delay really needed */ pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); } } -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irq); +DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_irq); +DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_irq); +DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_5, quirk_via_irq); /* * VIA VT82C598 has its device ID settable and many BIOSes diff --git a/drivers/pcmcia/i82365.c b/drivers/pcmcia/i82365.c index bd0308e8981..a2f05f48515 100644 --- a/drivers/pcmcia/i82365.c +++ b/drivers/pcmcia/i82365.c @@ -509,7 +509,8 @@ static irqreturn_t i365_count_irq(int irq, void *dev, struct pt_regs *regs) static u_int __init test_irq(u_short sock, int irq) { debug(2, " testing ISA irq %d\n", irq); - if (request_irq(irq, i365_count_irq, 0, "scan", i365_count_irq) != 0) + if (request_irq(irq, i365_count_irq, SA_PROBEIRQ, "scan", + i365_count_irq) != 0) return 1; irq_hits = 0; irq_sock = sock; msleep(10); @@ -561,7 +562,7 @@ static u_int __init isa_scan(u_short sock, u_int mask0) } else { /* Fallback: just find interrupts that aren't in use */ for (i = 0; i < 16; i++) - if ((mask0 & (1 << i)) && (_check_irq(i, 0) == 0)) + if ((mask0 & (1 << i)) && (_check_irq(i, SA_PROBEIRQ) == 0)) mask1 |= (1 << i); printk("default"); /* If scan failed, default to polled status */ @@ -725,7 +726,7 @@ static void __init add_pcic(int ns, int type) u_int cs_mask = mask & ((cs_irq) ? (1<<cs_irq) : ~(1<<12)); for (cs_irq = 15; cs_irq > 0; cs_irq--) if ((cs_mask & (1 << cs_irq)) && - (_check_irq(cs_irq, 0) == 0)) + (_check_irq(cs_irq, SA_PROBEIRQ) == 0)) break; if (cs_irq) { grab_irq = 1; diff --git a/drivers/rtc/rtc-dev.c b/drivers/rtc/rtc-dev.c index b1e3e6179e5..6c9ad92747f 100644 --- a/drivers/rtc/rtc-dev.c +++ b/drivers/rtc/rtc-dev.c @@ -58,7 +58,7 @@ rtc_dev_read(struct file *file, char __user *buf, size_t count, loff_t *ppos) unsigned long data; ssize_t ret; - if (count < sizeof(unsigned long)) + if (count != sizeof(unsigned int) && count < sizeof(unsigned long)) return -EINVAL; add_wait_queue(&rtc->irq_queue, &wait); @@ -90,11 +90,16 @@ rtc_dev_read(struct file *file, char __user *buf, size_t count, loff_t *ppos) if (ret == 0) { /* Check for any data updates */ if (rtc->ops->read_callback) - data = rtc->ops->read_callback(rtc->class_dev.dev, data); - - ret = put_user(data, (unsigned long __user *)buf); - if (ret == 0) - ret = sizeof(unsigned long); + data = rtc->ops->read_callback(rtc->class_dev.dev, + data); + + if (sizeof(int) != sizeof(long) && + count == sizeof(unsigned int)) + ret = put_user(data, (unsigned int __user *)buf) ?: + sizeof(unsigned int); + else + ret = put_user(data, (unsigned long __user *)buf) ?: + sizeof(unsigned long); } return ret; } diff --git a/drivers/rtc/rtc-sa1100.c b/drivers/rtc/rtc-sa1100.c index a23ec54989f..2bc8aad4721 100644 --- a/drivers/rtc/rtc-sa1100.c +++ b/drivers/rtc/rtc-sa1100.c @@ -178,9 +178,9 @@ static int sa1100_rtc_open(struct device *dev) return 0; fail_pi: - free_irq(IRQ_RTCAlrm, NULL); + free_irq(IRQ_RTCAlrm, dev); fail_ai: - free_irq(IRQ_RTC1Hz, NULL); + free_irq(IRQ_RTC1Hz, dev); fail_ui: return ret; } @@ -295,7 +295,7 @@ static int sa1100_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm) static int sa1100_rtc_proc(struct device *dev, struct seq_file *seq) { - seq_printf(seq, "trim/divider\t: 0x%08x\n", RTTR); + seq_printf(seq, "trim/divider\t: 0x%08lx\n", RTTR); seq_printf(seq, "alarm_IRQ\t: %s\n", (RTSR & RTSR_ALE) ? "yes" : "no" ); seq_printf(seq, "update_IRQ\t: %s\n", diff --git a/drivers/s390/block/dasd.c b/drivers/s390/block/dasd.c index a3bfebcf31e..cfb1fff3787 100644 --- a/drivers/s390/block/dasd.c +++ b/drivers/s390/block/dasd.c @@ -315,6 +315,11 @@ dasd_increase_state(struct dasd_device *device) rc = dasd_state_basic_to_ready(device); if (!rc && + device->state == DASD_STATE_UNFMT && + device->target > DASD_STATE_UNFMT) + rc = -EPERM; + + if (!rc && device->state == DASD_STATE_READY && device->target >= DASD_STATE_ONLINE) rc = dasd_state_ready_to_online(device); diff --git a/drivers/s390/block/dasd_devmap.c b/drivers/s390/block/dasd_devmap.c index c1c6f138115..216bc4fba19 100644 --- a/drivers/s390/block/dasd_devmap.c +++ b/drivers/s390/block/dasd_devmap.c @@ -45,6 +45,7 @@ struct dasd_devmap { unsigned int devindex; unsigned short features; struct dasd_device *device; + struct dasd_uid uid; }; /* @@ -716,6 +717,68 @@ dasd_discipline_show(struct device *dev, struct device_attribute *attr, char *bu static DEVICE_ATTR(discipline, 0444, dasd_discipline_show, NULL); +static ssize_t +dasd_alias_show(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct dasd_devmap *devmap; + int alias; + + devmap = dasd_find_busid(dev->bus_id); + spin_lock(&dasd_devmap_lock); + if (!IS_ERR(devmap)) + alias = devmap->uid.alias; + else + alias = 0; + spin_unlock(&dasd_devmap_lock); + + return sprintf(buf, alias ? "1\n" : "0\n"); +} + +static DEVICE_ATTR(alias, 0444, dasd_alias_show, NULL); + +static ssize_t +dasd_vendor_show(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct dasd_devmap *devmap; + char *vendor; + + devmap = dasd_find_busid(dev->bus_id); + spin_lock(&dasd_devmap_lock); + if (!IS_ERR(devmap) && strlen(devmap->uid.vendor) > 0) + vendor = devmap->uid.vendor; + else + vendor = ""; + spin_unlock(&dasd_devmap_lock); + + return snprintf(buf, PAGE_SIZE, "%s\n", vendor); +} + +static DEVICE_ATTR(vendor, 0444, dasd_vendor_show, NULL); + +#define UID_STRLEN ( /* vendor */ 3 + 1 + /* serial */ 14 + 1 +\ + /* SSID */ 4 + 1 + /* unit addr */ 2 + 1) + +static ssize_t +dasd_uid_show(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct dasd_devmap *devmap; + char uid[UID_STRLEN]; + + devmap = dasd_find_busid(dev->bus_id); + spin_lock(&dasd_devmap_lock); + if (!IS_ERR(devmap) && strlen(devmap->uid.vendor) > 0) + snprintf(uid, sizeof(uid), "%s.%s.%04x.%02x", + devmap->uid.vendor, devmap->uid.serial, + devmap->uid.ssid, devmap->uid.unit_addr); + else + uid[0] = 0; + spin_unlock(&dasd_devmap_lock); + + return snprintf(buf, PAGE_SIZE, "%s\n", uid); +} + +static DEVICE_ATTR(uid, 0444, dasd_uid_show, NULL); + /* * extended error-reporting */ @@ -759,6 +822,9 @@ static DEVICE_ATTR(eer_enabled, 0644, dasd_eer_show, dasd_eer_store); static struct attribute * dasd_attrs[] = { &dev_attr_readonly.attr, &dev_attr_discipline.attr, + &dev_attr_alias.attr, + &dev_attr_vendor.attr, + &dev_attr_uid.attr, &dev_attr_use_diag.attr, &dev_attr_eer_enabled.attr, NULL, @@ -768,6 +834,42 @@ static struct attribute_group dasd_attr_group = { .attrs = dasd_attrs, }; + +/* + * Return copy of the device unique identifier. + */ +int +dasd_get_uid(struct ccw_device *cdev, struct dasd_uid *uid) +{ + struct dasd_devmap *devmap; + + devmap = dasd_find_busid(cdev->dev.bus_id); + if (IS_ERR(devmap)) + return PTR_ERR(devmap); + spin_lock(&dasd_devmap_lock); + *uid = devmap->uid; + spin_unlock(&dasd_devmap_lock); + return 0; +} + +/* + * Register the given device unique identifier into devmap struct. + */ +int +dasd_set_uid(struct ccw_device *cdev, struct dasd_uid *uid) +{ + struct dasd_devmap *devmap; + + devmap = dasd_find_busid(cdev->dev.bus_id); + if (IS_ERR(devmap)) + return PTR_ERR(devmap); + spin_lock(&dasd_devmap_lock); + devmap->uid = *uid; + spin_unlock(&dasd_devmap_lock); + return 0; +} +EXPORT_SYMBOL(dasd_set_uid); + /* * Return value of the specified feature. */ diff --git a/drivers/s390/block/dasd_eckd.c b/drivers/s390/block/dasd_eckd.c index ee09ef33d08..7d5a6cee4bd 100644 --- a/drivers/s390/block/dasd_eckd.c +++ b/drivers/s390/block/dasd_eckd.c @@ -446,6 +446,39 @@ dasd_eckd_cdl_reclen(int recid) return LABEL_SIZE; } +/* + * Generate device unique id that specifies the physical device. + */ +static int +dasd_eckd_generate_uid(struct dasd_device *device, struct dasd_uid *uid) +{ + struct dasd_eckd_private *private; + struct dasd_eckd_confdata *confdata; + + private = (struct dasd_eckd_private *) device->private; + if (!private) + return -ENODEV; + confdata = &private->conf_data; + if (!confdata) + return -ENODEV; + + memset(uid, 0, sizeof(struct dasd_uid)); + strncpy(uid->vendor, confdata->ned1.HDA_manufacturer, + sizeof(uid->vendor) - 1); + EBCASC(uid->vendor, sizeof(uid->vendor) - 1); + strncpy(uid->serial, confdata->ned1.HDA_location, + sizeof(uid->serial) - 1); + EBCASC(uid->serial, sizeof(uid->serial) - 1); + uid->ssid = confdata->neq.subsystemID; + if (confdata->ned2.sneq.flags == 0x40) { + uid->alias = 1; + uid->unit_addr = confdata->ned2.sneq.base_unit_addr; + } else + uid->unit_addr = confdata->ned1.unit_addr; + + return 0; +} + static int dasd_eckd_read_conf(struct dasd_device *device) { @@ -507,11 +540,15 @@ dasd_eckd_read_conf(struct dasd_device *device) return 0; } - +/* + * Check device characteristics. + * If the device is accessible using ECKD discipline, the device is enabled. + */ static int dasd_eckd_check_characteristics(struct dasd_device *device) { struct dasd_eckd_private *private; + struct dasd_uid uid; void *rdc_data; int rc; @@ -536,6 +573,7 @@ dasd_eckd_check_characteristics(struct dasd_device *device) /* Read Device Characteristics */ rdc_data = (void *) &(private->rdc_data); + memset(rdc_data, 0, sizeof(rdc_data)); rc = read_dev_chars(device->cdev, &rdc_data, 64); if (rc) { DEV_MESSAGE(KERN_WARNING, device, @@ -556,8 +594,17 @@ dasd_eckd_check_characteristics(struct dasd_device *device) /* Read Configuration Data */ rc = dasd_eckd_read_conf (device); - return rc; + if (rc) + return rc; + + /* Generate device unique id and register in devmap */ + rc = dasd_eckd_generate_uid(device, &uid); + if (rc) + return rc; + rc = dasd_set_uid(device->cdev, &uid); + + return rc; } static struct dasd_ccw_req * diff --git a/drivers/s390/block/dasd_eckd.h b/drivers/s390/block/dasd_eckd.h index ad8524bb7bb..d5734e976e1 100644 --- a/drivers/s390/block/dasd_eckd.h +++ b/drivers/s390/block/dasd_eckd.h @@ -228,26 +228,36 @@ struct dasd_eckd_confdata { unsigned char HDA_manufacturer[3]; unsigned char HDA_location[2]; unsigned char HDA_seqno[12]; - __u16 ID; + __u8 ID; + __u8 unit_addr; } __attribute__ ((packed)) ned1; - struct { + union { struct { - unsigned char identifier:2; - unsigned char token_id:1; - unsigned char sno_valid:1; - unsigned char subst_sno:1; - unsigned char recNED:1; - unsigned char emuNED:1; - unsigned char reserved:1; - } __attribute__ ((packed)) flags; - __u8 descriptor; - __u8 reserved[2]; - unsigned char dev_type[6]; - unsigned char dev_model[3]; - unsigned char DASD_manufacturer[3]; - unsigned char DASD_location[2]; - unsigned char DASD_seqno[12]; - __u16 ID; + struct { + unsigned char identifier:2; + unsigned char token_id:1; + unsigned char sno_valid:1; + unsigned char subst_sno:1; + unsigned char recNED:1; + unsigned char emuNED:1; + unsigned char reserved:1; + } __attribute__ ((packed)) flags; + __u8 descriptor; + __u8 reserved[2]; + unsigned char dev_type[6]; + unsigned char dev_model[3]; + unsigned char DASD_manufacturer[3]; + unsigned char DASD_location[2]; + unsigned char DASD_seqno[12]; + __u16 ID; + } __attribute__ ((packed)) ned; + struct { + unsigned char flags; /* byte 0 */ + unsigned char res2[7]; /* byte 1- 7 */ + unsigned char sua_flags; /* byte 8 */ + __u8 base_unit_addr; /* byte 9 */ + unsigned char res3[22]; /* byte 10-31 */ + } __attribute__ ((packed)) sneq; } __attribute__ ((packed)) ned2; struct { struct { diff --git a/drivers/s390/block/dasd_int.h b/drivers/s390/block/dasd_int.h index 4293ba82752..d4b13e300a7 100644 --- a/drivers/s390/block/dasd_int.h +++ b/drivers/s390/block/dasd_int.h @@ -268,6 +268,16 @@ struct dasd_discipline { extern struct dasd_discipline *dasd_diag_discipline_pointer; +/* + * Unique identifier for dasd device. + */ +struct dasd_uid { + __u8 alias; + char vendor[4]; + char serial[15]; + __u16 ssid; + __u8 unit_addr; +}; /* * Notification numbers for extended error reporting notifications: @@ -516,6 +526,8 @@ void dasd_devmap_exit(void); struct dasd_device *dasd_create_device(struct ccw_device *); void dasd_delete_device(struct dasd_device *); +int dasd_get_uid(struct ccw_device *, struct dasd_uid *); +int dasd_set_uid(struct ccw_device *, struct dasd_uid *); int dasd_get_feature(struct ccw_device *, int); int dasd_set_feature(struct ccw_device *, int, int); diff --git a/drivers/s390/char/tape_3590.c b/drivers/s390/char/tape_3590.c index c3915f60a3a..d71ef1adea5 100644 --- a/drivers/s390/char/tape_3590.c +++ b/drivers/s390/char/tape_3590.c @@ -230,14 +230,16 @@ tape_3590_read_attmsg(struct tape_device *device) * These functions are used to schedule follow-up actions from within an * interrupt context (like unsolicited interrupts). */ +struct work_handler_data { + struct tape_device *device; + enum tape_op op; + struct work_struct work; +}; + static void tape_3590_work_handler(void *data) { - struct { - struct tape_device *device; - enum tape_op op; - struct work_struct work; - } *p = data; + struct work_handler_data *p = data; switch (p->op) { case TO_MSEN: @@ -257,11 +259,7 @@ tape_3590_work_handler(void *data) static int tape_3590_schedule_work(struct tape_device *device, enum tape_op op) { - struct { - struct tape_device *device; - enum tape_op op; - struct work_struct work; - } *p; + struct work_handler_data *p; if ((p = kzalloc(sizeof(*p), GFP_ATOMIC)) == NULL) return -ENOMEM; @@ -316,7 +314,7 @@ tape_3590_bread(struct tape_device *device, struct request *req) rq_for_each_bio(bio, req) { bio_for_each_segment(bv, bio, i) { - dst = kmap(bv->bv_page) + bv->bv_offset; + dst = page_address(bv->bv_page) + bv->bv_offset; for (off = 0; off < bv->bv_len; off += TAPEBLOCK_HSEC_SIZE) { ccw->flags = CCW_FLAG_CC; @@ -1168,6 +1166,7 @@ tape_3590_setup_device(struct tape_device *device) static void tape_3590_cleanup_device(struct tape_device *device) { + flush_scheduled_work(); tape_std_unassign(device); kfree(device->discdata); @@ -1234,6 +1233,7 @@ static struct tape_discipline tape_discipline_3590 = { static struct ccw_device_id tape_3590_ids[] = { {CCW_DEVICE_DEVTYPE(0x3590, 0, 0x3590, 0), .driver_info = tape_3590}, + {CCW_DEVICE_DEVTYPE(0x3592, 0, 0x3592, 0), .driver_info = tape_3592}, { /* end of list */ } }; diff --git a/drivers/s390/char/tape_std.h b/drivers/s390/char/tape_std.h index 2d311798edf..1fc95235934 100644 --- a/drivers/s390/char/tape_std.h +++ b/drivers/s390/char/tape_std.h @@ -153,6 +153,7 @@ enum s390_tape_type { tape_3480, tape_3490, tape_3590, + tape_3592, }; #endif // _TAPE_STD_H diff --git a/drivers/s390/cio/chsc.c b/drivers/s390/cio/chsc.c index 6412b2c3edd..72187e54dca 100644 --- a/drivers/s390/cio/chsc.c +++ b/drivers/s390/cio/chsc.c @@ -242,28 +242,10 @@ s390_subchannel_remove_chpid(struct device *dev, void *data) if (sch->vpm == mask) goto out_unreg; - if ((sch->schib.scsw.actl & (SCSW_ACTL_CLEAR_PEND | - SCSW_ACTL_HALT_PEND | - SCSW_ACTL_START_PEND | - SCSW_ACTL_RESUME_PEND)) && - (sch->schib.pmcw.lpum == mask)) { - int cc = cio_cancel(sch); - - if (cc == -ENODEV) - goto out_unreg; - - if (cc == -EINVAL) { - cc = cio_clear(sch); - if (cc == -ENODEV) - goto out_unreg; - /* Call handler. */ - if (sch->driver && sch->driver->termination) - sch->driver->termination(&sch->dev); - goto out_unlock; - } - } else if ((sch->schib.scsw.actl & SCSW_ACTL_DEVACT) && - (sch->schib.scsw.actl & SCSW_ACTL_SCHACT) && - (sch->schib.pmcw.lpum == mask)) { + if ((sch->schib.scsw.actl & SCSW_ACTL_DEVACT) && + (sch->schib.scsw.actl & SCSW_ACTL_SCHACT) && + (sch->schib.pmcw.lpum == mask) && + (sch->vpm == 0)) { int cc; cc = cio_clear(sch); @@ -653,13 +635,13 @@ __chp_add(struct subchannel_id schid, void *data) if (sch->schib.pmcw.chpid[i] == chp->id) { if (stsch(sch->schid, &sch->schib) != 0) { /* Endgame. */ - spin_unlock(&sch->lock); + spin_unlock_irq(&sch->lock); return -ENXIO; } break; } if (i==8) { - spin_unlock(&sch->lock); + spin_unlock_irq(&sch->lock); return 0; } sch->lpm = ((sch->schib.pmcw.pim & diff --git a/drivers/s390/cio/qdio.c b/drivers/s390/cio/qdio.c index 814f9258ce0..96f519281d9 100644 --- a/drivers/s390/cio/qdio.c +++ b/drivers/s390/cio/qdio.c @@ -38,6 +38,7 @@ #include <linux/kernel.h> #include <linux/proc_fs.h> #include <linux/timer.h> +#include <linux/mempool.h> #include <asm/ccwdev.h> #include <asm/io.h> @@ -80,6 +81,8 @@ static int indicator_used[INDICATORS_PER_CACHELINE]; static __u32 * volatile indicators; static __u32 volatile spare_indicator; static atomic_t spare_indicator_usecount; +#define QDIO_MEMPOOL_SCSSC_ELEMENTS 2 +static mempool_t *qdio_mempool_scssc; static debug_info_t *qdio_dbf_setup; static debug_info_t *qdio_dbf_sbal; @@ -1637,7 +1640,7 @@ next: } kfree(irq_ptr->qdr); - kfree(irq_ptr); + free_page((unsigned long) irq_ptr); } static void @@ -2304,7 +2307,7 @@ qdio_get_ssqd_information(struct qdio_irq *irq_ptr) QDIO_DBF_TEXT0(0,setup,"getssqd"); qdioac = 0; - ssqd_area = (void *)get_zeroed_page(GFP_KERNEL | GFP_DMA); + ssqd_area = mempool_alloc(qdio_mempool_scssc, GFP_ATOMIC); if (!ssqd_area) { QDIO_PRINT_WARN("Could not get memory for chsc. Using all " \ "SIGAs for sch x%x.\n", irq_ptr->schid.sch_no); @@ -2364,7 +2367,7 @@ qdio_get_ssqd_information(struct qdio_irq *irq_ptr) out: qdio_check_subchannel_qebsm(irq_ptr, qdioac, ssqd_area->sch_token); - free_page ((unsigned long) ssqd_area); + mempool_free(ssqd_area, qdio_mempool_scssc); irq_ptr->qdioac = qdioac; } @@ -2458,7 +2461,7 @@ tiqdio_set_subchannel_ind(struct qdio_irq *irq_ptr, int reset_to_zero) virt_to_phys((volatile void *)irq_ptr->dev_st_chg_ind); } - scssc_area = (void *)get_zeroed_page(GFP_KERNEL | GFP_DMA); + scssc_area = mempool_alloc(qdio_mempool_scssc, GFP_ATOMIC); if (!scssc_area) { QDIO_PRINT_WARN("No memory for setting indicators on " \ "subchannel 0.%x.%x.\n", @@ -2514,7 +2517,7 @@ tiqdio_set_subchannel_ind(struct qdio_irq *irq_ptr, int reset_to_zero) QDIO_DBF_HEX2(0,setup,&real_addr_dev_st_chg_ind,sizeof(unsigned long)); result = 0; out: - free_page ((unsigned long) scssc_area); + mempool_free(scssc_area, qdio_mempool_scssc); return result; } @@ -2543,7 +2546,7 @@ tiqdio_set_delay_target(struct qdio_irq *irq_ptr, unsigned long delay_target) if (!irq_ptr->is_thinint_irq) return -ENODEV; - scsscf_area = (void *)get_zeroed_page(GFP_KERNEL | GFP_DMA); + scsscf_area = mempool_alloc(qdio_mempool_scssc, GFP_ATOMIC); if (!scsscf_area) { QDIO_PRINT_WARN("No memory for setting delay target on " \ "subchannel 0.%x.%x.\n", @@ -2581,7 +2584,7 @@ tiqdio_set_delay_target(struct qdio_irq *irq_ptr, unsigned long delay_target) QDIO_DBF_HEX2(0,trace,&delay_target,sizeof(unsigned long)); result = 0; /* not critical */ out: - free_page ((unsigned long) scsscf_area); + mempool_free(scsscf_area, qdio_mempool_scssc); return result; } @@ -2980,7 +2983,7 @@ qdio_allocate(struct qdio_initialize *init_data) qdio_allocate_do_dbf(init_data); /* create irq */ - irq_ptr = kzalloc(sizeof(struct qdio_irq), GFP_KERNEL | GFP_DMA); + irq_ptr = (void *) get_zeroed_page(GFP_KERNEL | GFP_DMA); QDIO_DBF_TEXT0(0,setup,"irq_ptr:"); QDIO_DBF_HEX0(0,setup,&irq_ptr,sizeof(void*)); @@ -2995,7 +2998,7 @@ qdio_allocate(struct qdio_initialize *init_data) /* QDR must be in DMA area since CCW data address is only 32 bit */ irq_ptr->qdr=kmalloc(sizeof(struct qdr), GFP_KERNEL | GFP_DMA); if (!(irq_ptr->qdr)) { - kfree(irq_ptr); + free_page((unsigned long) irq_ptr); QDIO_PRINT_ERR("kmalloc of irq_ptr->qdr failed!\n"); return -ENOMEM; } @@ -3780,6 +3783,16 @@ oom: return -ENOMEM; } +static void *qdio_mempool_alloc(gfp_t gfp_mask, void *size) +{ + return (void *) get_zeroed_page(gfp_mask|GFP_DMA); +} + +static void qdio_mempool_free(void *element, void *size) +{ + free_page((unsigned long) element); +} + static int __init init_QDIO(void) { @@ -3809,6 +3822,10 @@ init_QDIO(void) qdio_add_procfs_entry(); + qdio_mempool_scssc = mempool_create(QDIO_MEMPOOL_SCSSC_ELEMENTS, + qdio_mempool_alloc, + qdio_mempool_free, NULL); + if (tiqdio_check_chsc_availability()) QDIO_PRINT_ERR("Not all CHSCs supported. Continuing.\n"); @@ -3824,6 +3841,7 @@ cleanup_QDIO(void) qdio_remove_procfs_entry(); qdio_release_qdio_memory(); qdio_unregister_dbf_views(); + mempool_destroy(qdio_mempool_scssc); printk("qdio: %s: module removed\n",version); } diff --git a/drivers/s390/net/qeth_main.c b/drivers/s390/net/qeth_main.c index b3c6e790779..cb14642d97a 100644 --- a/drivers/s390/net/qeth_main.c +++ b/drivers/s390/net/qeth_main.c @@ -8014,7 +8014,6 @@ static int (*qeth_old_arp_constructor) (struct neighbour *); static struct neigh_ops arp_direct_ops_template = { .family = AF_INET, - .destructor = NULL, .solicit = NULL, .error_report = NULL, .output = dev_queue_xmit, diff --git a/drivers/s390/s390mach.c b/drivers/s390/s390mach.c index 3bf46660351..f99e55308b3 100644 --- a/drivers/s390/s390mach.c +++ b/drivers/s390/s390mach.c @@ -13,6 +13,7 @@ #include <linux/sched.h> #include <linux/errno.h> #include <linux/workqueue.h> +#include <linux/time.h> #include <asm/lowcore.h> @@ -362,12 +363,19 @@ s390_revalidate_registers(struct mci *mci) return kill_task; } +#define MAX_IPD_COUNT 29 +#define MAX_IPD_TIME (5 * 60 * USEC_PER_SEC) /* 5 minutes */ + /* * machine check handler. */ void s390_do_machine_check(struct pt_regs *regs) { + static DEFINE_SPINLOCK(ipd_lock); + static unsigned long long last_ipd; + static int ipd_count; + unsigned long long tmp; struct mci *mci; struct mcck_struct *mcck; int umode; @@ -404,11 +412,27 @@ s390_do_machine_check(struct pt_regs *regs) s390_handle_damage("processing backup machine " "check with damage."); } - if (!umode) - s390_handle_damage("processing backup machine " - "check in kernel mode."); - mcck->kill_task = 1; - mcck->mcck_code = *(unsigned long long *) mci; + + /* + * Nullifying exigent condition, therefore we might + * retry this instruction. + */ + + spin_lock(&ipd_lock); + + tmp = get_clock(); + + if (((tmp - last_ipd) >> 12) < MAX_IPD_TIME) + ipd_count++; + else + ipd_count = 1; + + last_ipd = tmp; + + if (ipd_count == MAX_IPD_COUNT) + s390_handle_damage("too many ipd retries."); + + spin_unlock(&ipd_lock); } else { /* Processing damage -> stopping machine */ diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig index 3e7302692db..a480a3742d4 100644 --- a/drivers/scsi/Kconfig +++ b/drivers/scsi/Kconfig @@ -446,7 +446,9 @@ config SCSI_DPT_I2O config SCSI_ADVANSYS tristate "AdvanSys SCSI support" - depends on (ISA || EISA || PCI) && SCSI && BROKEN + depends on SCSI + depends on ISA || EISA || PCI + depends on BROKEN || X86_32 help This is a driver for all SCSI host adapters manufactured by AdvanSys. It is documented in the kernel source in diff --git a/drivers/scsi/advansys.c b/drivers/scsi/advansys.c index 28b93057b60..2a419634b25 100644 --- a/drivers/scsi/advansys.c +++ b/drivers/scsi/advansys.c @@ -2051,7 +2051,7 @@ STATIC ASC_DCNT AscGetMaxDmaCount(ushort); #define ADV_VADDR_TO_U32 virt_to_bus #define ADV_U32_TO_VADDR bus_to_virt -#define AdvPortAddr ulong /* Virtual memory address size */ +#define AdvPortAddr void __iomem * /* Virtual memory address size */ /* * Define Adv Library required memory access macros. diff --git a/drivers/scsi/aic7xxx/aic7xxx_osm_pci.c b/drivers/scsi/aic7xxx/aic7xxx_osm_pci.c index cb30d9c1153..0c9c2f400bf 100644 --- a/drivers/scsi/aic7xxx/aic7xxx_osm_pci.c +++ b/drivers/scsi/aic7xxx/aic7xxx_osm_pci.c @@ -219,6 +219,7 @@ ahc_linux_pci_dev_probe(struct pci_dev *pdev, const struct pci_device_id *ent) ahc->flags |= AHC_39BIT_ADDRESSING; } else { if (dma_set_mask(dev, DMA_32BIT_MASK)) { + ahc_free(ahc); printk(KERN_WARNING "aic7xxx: No suitable DMA available.\n"); return (-ENODEV); } diff --git a/drivers/scsi/aic7xxx/aic7xxx_pci.c b/drivers/scsi/aic7xxx/aic7xxx_pci.c index 5f586140e05..3adecef2178 100644 --- a/drivers/scsi/aic7xxx/aic7xxx_pci.c +++ b/drivers/scsi/aic7xxx/aic7xxx_pci.c @@ -2036,12 +2036,12 @@ ahc_pci_resume(struct ahc_softc *ahc) * that the OS doesn't know about and rely on our chip * reset handler to handle the rest. */ - ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4, - ahc->bus_softc.pci_softc.devconfig); - ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/1, - ahc->bus_softc.pci_softc.command); - ahc_pci_write_config(ahc->dev_softc, CSIZE_LATTIME, /*bytes*/1, - ahc->bus_softc.pci_softc.csize_lattime); + ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, + ahc->bus_softc.pci_softc.devconfig, /*bytes*/4); + ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, + ahc->bus_softc.pci_softc.command, /*bytes*/1); + ahc_pci_write_config(ahc->dev_softc, CSIZE_LATTIME, + ahc->bus_softc.pci_softc.csize_lattime, /*bytes*/1); if ((ahc->flags & AHC_HAS_TERM_LOGIC) != 0) { struct seeprom_descriptor sd; u_int sxfrctl1; diff --git a/drivers/scsi/ibmvscsi/ibmvscsi.c b/drivers/scsi/ibmvscsi/ibmvscsi.c index 0a8ad37ae89..2e9be83a697 100644 --- a/drivers/scsi/ibmvscsi/ibmvscsi.c +++ b/drivers/scsi/ibmvscsi/ibmvscsi.c @@ -739,7 +739,8 @@ static void send_mad_adapter_info(struct ibmvscsi_host_data *hostdata) { struct viosrp_adapter_info *req; struct srp_event_struct *evt_struct; - + dma_addr_t addr; + evt_struct = get_event_struct(&hostdata->pool); if (!evt_struct) { printk(KERN_ERR "ibmvscsi: couldn't allocate an event " @@ -757,10 +758,10 @@ static void send_mad_adapter_info(struct ibmvscsi_host_data *hostdata) req->common.type = VIOSRP_ADAPTER_INFO_TYPE; req->common.length = sizeof(hostdata->madapter_info); - req->buffer = dma_map_single(hostdata->dev, - &hostdata->madapter_info, - sizeof(hostdata->madapter_info), - DMA_BIDIRECTIONAL); + req->buffer = addr = dma_map_single(hostdata->dev, + &hostdata->madapter_info, + sizeof(hostdata->madapter_info), + DMA_BIDIRECTIONAL); if (dma_mapping_error(req->buffer)) { printk(KERN_ERR @@ -770,8 +771,13 @@ static void send_mad_adapter_info(struct ibmvscsi_host_data *hostdata) return; } - if (ibmvscsi_send_srp_event(evt_struct, hostdata)) + if (ibmvscsi_send_srp_event(evt_struct, hostdata)) { printk(KERN_ERR "ibmvscsi: couldn't send ADAPTER_INFO_REQ!\n"); + dma_unmap_single(hostdata->dev, + addr, + sizeof(hostdata->madapter_info), + DMA_BIDIRECTIONAL); + } }; /** @@ -1259,6 +1265,7 @@ static int ibmvscsi_do_host_config(struct ibmvscsi_host_data *hostdata, { struct viosrp_host_config *host_config; struct srp_event_struct *evt_struct; + dma_addr_t addr; int rc; evt_struct = get_event_struct(&hostdata->pool); @@ -1279,8 +1286,9 @@ static int ibmvscsi_do_host_config(struct ibmvscsi_host_data *hostdata, memset(host_config, 0x00, sizeof(*host_config)); host_config->common.type = VIOSRP_HOST_CONFIG_TYPE; host_config->common.length = length; - host_config->buffer = dma_map_single(hostdata->dev, buffer, length, - DMA_BIDIRECTIONAL); + host_config->buffer = addr = dma_map_single(hostdata->dev, buffer, + length, + DMA_BIDIRECTIONAL); if (dma_mapping_error(host_config->buffer)) { printk(KERN_ERR @@ -1291,11 +1299,9 @@ static int ibmvscsi_do_host_config(struct ibmvscsi_host_data *hostdata, init_completion(&evt_struct->comp); rc = ibmvscsi_send_srp_event(evt_struct, hostdata); - if (rc == 0) { + if (rc == 0) wait_for_completion(&evt_struct->comp); - dma_unmap_single(hostdata->dev, host_config->buffer, - length, DMA_BIDIRECTIONAL); - } + dma_unmap_single(hostdata->dev, addr, length, DMA_BIDIRECTIONAL); return rc; } diff --git a/drivers/scsi/lpfc/lpfc_crtn.h b/drivers/scsi/lpfc/lpfc_crtn.h index fad607b2e6f..ee22173fce4 100644 --- a/drivers/scsi/lpfc/lpfc_crtn.h +++ b/drivers/scsi/lpfc/lpfc_crtn.h @@ -27,7 +27,6 @@ void lpfc_config_link(struct lpfc_hba *, LPFC_MBOXQ_t *); int lpfc_read_sparam(struct lpfc_hba *, LPFC_MBOXQ_t *); void lpfc_read_config(struct lpfc_hba *, LPFC_MBOXQ_t *); void lpfc_read_lnk_stat(struct lpfc_hba *, LPFC_MBOXQ_t *); -void lpfc_set_slim(struct lpfc_hba *, LPFC_MBOXQ_t *, uint32_t, uint32_t); int lpfc_reg_login(struct lpfc_hba *, uint32_t, uint8_t *, LPFC_MBOXQ_t *, uint32_t); void lpfc_unreg_login(struct lpfc_hba *, uint32_t, LPFC_MBOXQ_t *); diff --git a/drivers/scsi/lpfc/lpfc_disc.h b/drivers/scsi/lpfc/lpfc_disc.h index 8932b1be2b6..41cf5d3ea6c 100644 --- a/drivers/scsi/lpfc/lpfc_disc.h +++ b/drivers/scsi/lpfc/lpfc_disc.h @@ -113,6 +113,7 @@ struct lpfc_nodelist { #define NLP_NPR_ADISC 0x2000000 /* Issue ADISC when dq'ed from NPR list */ #define NLP_DELAY_REMOVE 0x4000000 /* Defer removal till end of DSM */ +#define NLP_NODEV_REMOVE 0x8000000 /* Defer removal till discovery ends */ /* Defines for list searchs */ #define NLP_SEARCH_MAPPED 0x1 /* search mapped */ diff --git a/drivers/scsi/lpfc/lpfc_els.c b/drivers/scsi/lpfc/lpfc_els.c index 4813beaaca8..283b7d824c3 100644 --- a/drivers/scsi/lpfc/lpfc_els.c +++ b/drivers/scsi/lpfc/lpfc_els.c @@ -302,10 +302,6 @@ lpfc_cmpl_els_flogi_fabric(struct lpfc_hba *phba, struct lpfc_nodelist *ndlp, if (lpfc_reg_login(phba, Fabric_DID, (uint8_t *) sp, mbox, 0)) goto fail_free_mbox; - /* - * set_slim mailbox command needs to execute first, - * queue this command to be processed later. - */ mbox->mbox_cmpl = lpfc_mbx_cmpl_fabric_reg_login; mbox->context2 = ndlp; @@ -781,25 +777,26 @@ lpfc_cmpl_els_plogi(struct lpfc_hba * phba, struct lpfc_iocbq * cmdiocb, if (disc && phba->num_disc_nodes) { /* Check to see if there are more PLOGIs to be sent */ lpfc_more_plogi(phba); - } - if (phba->num_disc_nodes == 0) { - spin_lock_irq(phba->host->host_lock); - phba->fc_flag &= ~FC_NDISC_ACTIVE; - spin_unlock_irq(phba->host->host_lock); + if (phba->num_disc_nodes == 0) { + spin_lock_irq(phba->host->host_lock); + phba->fc_flag &= ~FC_NDISC_ACTIVE; + spin_unlock_irq(phba->host->host_lock); - lpfc_can_disctmo(phba); - if (phba->fc_flag & FC_RSCN_MODE) { - /* Check to see if more RSCNs came in while we were - * processing this one. - */ - if ((phba->fc_rscn_id_cnt == 0) && - (!(phba->fc_flag & FC_RSCN_DISCOVERY))) { - spin_lock_irq(phba->host->host_lock); - phba->fc_flag &= ~FC_RSCN_MODE; - spin_unlock_irq(phba->host->host_lock); - } else { - lpfc_els_handle_rscn(phba); + lpfc_can_disctmo(phba); + if (phba->fc_flag & FC_RSCN_MODE) { + /* + * Check to see if more RSCNs came in while + * we were processing this one. + */ + if ((phba->fc_rscn_id_cnt == 0) && + (!(phba->fc_flag & FC_RSCN_DISCOVERY))) { + spin_lock_irq(phba->host->host_lock); + phba->fc_flag &= ~FC_RSCN_MODE; + spin_unlock_irq(phba->host->host_lock); + } else { + lpfc_els_handle_rscn(phba); + } } } } @@ -1263,7 +1260,7 @@ lpfc_issue_els_logo(struct lpfc_hba * phba, struct lpfc_nodelist * ndlp, psli = &phba->sli; pring = &psli->ring[LPFC_ELS_RING]; - cmdsize = 2 * (sizeof (uint32_t) + sizeof (struct lpfc_name)); + cmdsize = (2 * sizeof (uint32_t)) + sizeof (struct lpfc_name); elsiocb = lpfc_prep_els_iocb(phba, 1, cmdsize, retry, ndlp, ndlp->nlp_DID, ELS_CMD_LOGO); if (!elsiocb) @@ -1451,22 +1448,23 @@ lpfc_cancel_retry_delay_tmo(struct lpfc_hba *phba, struct lpfc_nodelist * nlp) * PLOGIs to be sent */ lpfc_more_plogi(phba); - } - if (phba->num_disc_nodes == 0) { - phba->fc_flag &= ~FC_NDISC_ACTIVE; - lpfc_can_disctmo(phba); - if (phba->fc_flag & FC_RSCN_MODE) { - /* Check to see if more RSCNs - * came in while we were - * processing this one. - */ - if((phba->fc_rscn_id_cnt==0) && - (!(phba->fc_flag & FC_RSCN_DISCOVERY))) { - phba->fc_flag &= ~FC_RSCN_MODE; - } - else { - lpfc_els_handle_rscn(phba); + if (phba->num_disc_nodes == 0) { + phba->fc_flag &= ~FC_NDISC_ACTIVE; + lpfc_can_disctmo(phba); + if (phba->fc_flag & FC_RSCN_MODE) { + /* + * Check to see if more RSCNs + * came in while we were + * processing this one. + */ + if((phba->fc_rscn_id_cnt==0) && + !(phba->fc_flag & FC_RSCN_DISCOVERY)) { + phba->fc_flag &= ~FC_RSCN_MODE; + } + else { + lpfc_els_handle_rscn(phba); + } } } } @@ -1872,9 +1870,6 @@ lpfc_cmpl_els_acc(struct lpfc_hba * phba, struct lpfc_iocbq * cmdiocb, if (mbox) { if ((rspiocb->iocb.ulpStatus == 0) && (ndlp->nlp_flag & NLP_ACC_REGLOGIN)) { - /* set_slim mailbox command needs to execute first, - * queue this command to be processed later. - */ lpfc_unreg_rpi(phba, ndlp); mbox->mbox_cmpl = lpfc_mbx_cmpl_reg_login; mbox->context2 = ndlp; @@ -1920,6 +1915,7 @@ lpfc_els_rsp_acc(struct lpfc_hba * phba, uint32_t flag, uint8_t *pcmd; uint16_t cmdsize; int rc; + ELS_PKT *els_pkt_ptr; psli = &phba->sli; pring = &psli->ring[LPFC_ELS_RING]; /* ELS ring */ @@ -1958,6 +1954,23 @@ lpfc_els_rsp_acc(struct lpfc_hba * phba, uint32_t flag, pcmd += sizeof (uint32_t); memcpy(pcmd, &phba->fc_sparam, sizeof (struct serv_parm)); break; + case ELS_CMD_PRLO: + cmdsize = sizeof (uint32_t) + sizeof (PRLO); + elsiocb = lpfc_prep_els_iocb(phba, 0, cmdsize, oldiocb->retry, + ndlp, ndlp->nlp_DID, ELS_CMD_PRLO); + if (!elsiocb) + return 1; + + icmd = &elsiocb->iocb; + icmd->ulpContext = oldcmd->ulpContext; /* Xri */ + pcmd = (((struct lpfc_dmabuf *) elsiocb->context2)->virt); + + memcpy(pcmd, ((struct lpfc_dmabuf *) oldiocb->context2)->virt, + sizeof (uint32_t) + sizeof (PRLO)); + *((uint32_t *) (pcmd)) = ELS_CMD_PRLO_ACC; + els_pkt_ptr = (ELS_PKT *) pcmd; + els_pkt_ptr->un.prlo.acceptRspCode = PRLO_REQ_EXECUTED; + break; default: return 1; } @@ -2498,7 +2511,7 @@ lpfc_els_rcv_rscn(struct lpfc_hba * phba, /* If we are about to begin discovery, just ACC the RSCN. * Discovery processing will satisfy it. */ - if (phba->hba_state < LPFC_NS_QRY) { + if (phba->hba_state <= LPFC_NS_QRY) { lpfc_els_rsp_acc(phba, ELS_CMD_ACC, cmdiocb, ndlp, NULL, newnode); return 0; diff --git a/drivers/scsi/lpfc/lpfc_hbadisc.c b/drivers/scsi/lpfc/lpfc_hbadisc.c index 6721e679df6..adb086009ae 100644 --- a/drivers/scsi/lpfc/lpfc_hbadisc.c +++ b/drivers/scsi/lpfc/lpfc_hbadisc.c @@ -311,8 +311,8 @@ lpfc_workq_post_event(struct lpfc_hba * phba, void *arg1, void *arg2, evtp->evt_arg2 = arg2; evtp->evt = evt; - list_add_tail(&evtp->evt_listp, &phba->work_list); spin_lock_irq(phba->host->host_lock); + list_add_tail(&evtp->evt_listp, &phba->work_list); if (phba->work_wait) wake_up(phba->work_wait); spin_unlock_irq(phba->host->host_lock); @@ -1071,10 +1071,6 @@ lpfc_register_remote_port(struct lpfc_hba * phba, /* initialize static port data */ rport->maxframe_size = ndlp->nlp_maxframe; rport->supported_classes = ndlp->nlp_class_sup; - if ((rport->scsi_target_id != -1) && - (rport->scsi_target_id < MAX_FCP_TARGET)) { - ndlp->nlp_sid = rport->scsi_target_id; - } rdata = rport->dd_data; rdata->pnode = ndlp; @@ -1087,6 +1083,10 @@ lpfc_register_remote_port(struct lpfc_hba * phba, if (rport_ids.roles != FC_RPORT_ROLE_UNKNOWN) fc_remote_port_rolechg(rport, rport_ids.roles); + if ((rport->scsi_target_id != -1) && + (rport->scsi_target_id < MAX_FCP_TARGET)) { + ndlp->nlp_sid = rport->scsi_target_id; + } return; } @@ -1238,6 +1238,7 @@ lpfc_nlp_list(struct lpfc_hba * phba, struct lpfc_nodelist * nlp, int list) evt_listp); } + nlp->nlp_flag &= ~NLP_NODEV_REMOVE; nlp->nlp_type |= NLP_FC_NODE; break; case NLP_MAPPED_LIST: @@ -1258,6 +1259,7 @@ lpfc_nlp_list(struct lpfc_hba * phba, struct lpfc_nodelist * nlp, int list) evt_listp); } + nlp->nlp_flag &= ~NLP_NODEV_REMOVE; break; case NLP_NPR_LIST: nlp->nlp_flag |= list; @@ -1402,6 +1404,8 @@ lpfc_check_sli_ndlp(struct lpfc_hba * phba, if (icmd->ulpContext == (volatile ushort)ndlp->nlp_rpi) return 1; case CMD_ELS_REQUEST64_CR: + if (icmd->un.elsreq64.remoteID == ndlp->nlp_DID) + return 1; case CMD_XMIT_ELS_RSP64_CX: if (iocb->context1 == (uint8_t *) ndlp) return 1; @@ -1901,10 +1905,8 @@ lpfc_setup_disc_node(struct lpfc_hba * phba, uint32_t did) */ if (ndlp->nlp_flag & NLP_DELAY_TMO) lpfc_cancel_retry_delay_tmo(phba, ndlp); - } else { - ndlp->nlp_flag &= ~NLP_NPR_2B_DISC; + } else ndlp = NULL; - } } else { flg = ndlp->nlp_flag & NLP_LIST_MASK; if ((flg == NLP_ADISC_LIST) || (flg == NLP_PLOGI_LIST)) diff --git a/drivers/scsi/lpfc/lpfc_hw.h b/drivers/scsi/lpfc/lpfc_hw.h index 54d04188f7c..eedf9880136 100644 --- a/drivers/scsi/lpfc/lpfc_hw.h +++ b/drivers/scsi/lpfc/lpfc_hw.h @@ -449,6 +449,7 @@ struct serv_parm { /* Structure is in Big Endian format */ #define ELS_CMD_RRQ 0x12000000 #define ELS_CMD_PRLI 0x20100014 #define ELS_CMD_PRLO 0x21100014 +#define ELS_CMD_PRLO_ACC 0x02100014 #define ELS_CMD_PDISC 0x50000000 #define ELS_CMD_FDISC 0x51000000 #define ELS_CMD_ADISC 0x52000000 @@ -484,6 +485,7 @@ struct serv_parm { /* Structure is in Big Endian format */ #define ELS_CMD_RRQ 0x12 #define ELS_CMD_PRLI 0x14001020 #define ELS_CMD_PRLO 0x14001021 +#define ELS_CMD_PRLO_ACC 0x14001002 #define ELS_CMD_PDISC 0x50 #define ELS_CMD_FDISC 0x51 #define ELS_CMD_ADISC 0x52 @@ -1539,6 +1541,7 @@ typedef struct { #define FLAGS_TOPOLOGY_FAILOVER 0x0400 /* Bit 10 */ #define FLAGS_LINK_SPEED 0x0800 /* Bit 11 */ +#define FLAGS_IMED_ABORT 0x04000 /* Bit 14 */ uint32_t link_speed; #define LINK_SPEED_AUTO 0 /* Auto selection */ diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c index 66d5d003555..908d0f27706 100644 --- a/drivers/scsi/lpfc/lpfc_init.c +++ b/drivers/scsi/lpfc/lpfc_init.c @@ -294,15 +294,6 @@ lpfc_config_port_post(struct lpfc_hba * phba) } } - /* This should turn on DELAYED ABTS for ELS timeouts */ - lpfc_set_slim(phba, pmb, 0x052198, 0x1); - if (lpfc_sli_issue_mbox(phba, pmb, MBX_POLL) != MBX_SUCCESS) { - phba->hba_state = LPFC_HBA_ERROR; - mempool_free( pmb, phba->mbox_mem_pool); - return -EIO; - } - - lpfc_read_config(phba, pmb); if (lpfc_sli_issue_mbox(phba, pmb, MBX_POLL) != MBX_SUCCESS) { lpfc_printf_log(phba, @@ -804,7 +795,7 @@ lpfc_get_hba_model_desc(struct lpfc_hba * phba, uint8_t * mdp, uint8_t * descp) int max_speed; char * ports; char * bus; - } m; + } m = {"<Unknown>", 0, "", ""}; pci_read_config_byte(phba->pcidev, PCI_HEADER_TYPE, &hdrtype); ports = (hdrtype == 0x80) ? "2-port " : ""; @@ -1627,7 +1618,7 @@ lpfc_pci_probe_one(struct pci_dev *pdev, const struct pci_device_id *pid) error = lpfc_alloc_sysfs_attr(phba); if (error) - goto out_kthread_stop; + goto out_remove_host; error = request_irq(phba->pcidev->irq, lpfc_intr_handler, SA_SHIRQ, LPFC_DRIVER_NAME, phba); @@ -1644,8 +1635,10 @@ lpfc_pci_probe_one(struct pci_dev *pdev, const struct pci_device_id *pid) phba->HCregaddr = phba->ctrl_regs_memmap_p + HC_REG_OFFSET; error = lpfc_sli_hba_setup(phba); - if (error) + if (error) { + error = -ENODEV; goto out_free_irq; + } if (phba->cfg_poll & DISABLE_FCP_RING_INT) { spin_lock_irq(phba->host->host_lock); @@ -1700,6 +1693,9 @@ out_free_irq: free_irq(phba->pcidev->irq, phba); out_free_sysfs_attr: lpfc_free_sysfs_attr(phba); +out_remove_host: + fc_remove_host(phba->host); + scsi_remove_host(phba->host); out_kthread_stop: kthread_stop(phba->worker_thread); out_free_iocbq: @@ -1721,12 +1717,14 @@ out_iounmap_slim: out_idr_remove: idr_remove(&lpfc_hba_index, phba->brd_no); out_put_host: + phba->host = NULL; scsi_host_put(host); out_release_regions: pci_release_regions(pdev); out_disable_device: pci_disable_device(pdev); out: + pci_set_drvdata(pdev, NULL); return error; } diff --git a/drivers/scsi/lpfc/lpfc_mbox.c b/drivers/scsi/lpfc/lpfc_mbox.c index c585e2b2e58..e42f22aaf71 100644 --- a/drivers/scsi/lpfc/lpfc_mbox.c +++ b/drivers/scsi/lpfc/lpfc_mbox.c @@ -200,6 +200,9 @@ lpfc_init_link(struct lpfc_hba * phba, break; } + /* Enable asynchronous ABTS responses from firmware */ + mb->un.varInitLnk.link_flags |= FLAGS_IMED_ABORT; + /* NEW_FEATURE * Setting up the link speed */ @@ -292,36 +295,6 @@ lpfc_unreg_did(struct lpfc_hba * phba, uint32_t did, LPFC_MBOXQ_t * pmb) return; } -/***********************************************/ - -/* command to write slim */ -/***********************************************/ -void -lpfc_set_slim(struct lpfc_hba * phba, LPFC_MBOXQ_t * pmb, uint32_t addr, - uint32_t value) -{ - MAILBOX_t *mb; - - mb = &pmb->mb; - memset(pmb, 0, sizeof (LPFC_MBOXQ_t)); - - /* addr = 0x090597 is AUTO ABTS disable for ELS commands */ - /* addr = 0x052198 is DELAYED ABTS enable for ELS commands */ - - /* - * Always turn on DELAYED ABTS for ELS timeouts - */ - if ((addr == 0x052198) && (value == 0)) - value = 1; - - mb->un.varWords[0] = addr; - mb->un.varWords[1] = value; - - mb->mbxCommand = MBX_SET_SLIM; - mb->mbxOwner = OWN_HOST; - return; -} - /**********************************************/ /* lpfc_read_nv Issue a READ CONFIG */ /* mailbox command */ diff --git a/drivers/scsi/lpfc/lpfc_nportdisc.c b/drivers/scsi/lpfc/lpfc_nportdisc.c index 3d77bd999b7..27d60ad897c 100644 --- a/drivers/scsi/lpfc/lpfc_nportdisc.c +++ b/drivers/scsi/lpfc/lpfc_nportdisc.c @@ -465,14 +465,18 @@ lpfc_rcv_padisc(struct lpfc_hba * phba, static int lpfc_rcv_logo(struct lpfc_hba * phba, struct lpfc_nodelist * ndlp, - struct lpfc_iocbq *cmdiocb) + struct lpfc_iocbq *cmdiocb, + uint32_t els_cmd) { /* Put ndlp on NPR list with 1 sec timeout for plogi, ACC logo */ /* Only call LOGO ACC for first LOGO, this avoids sending unnecessary * PLOGIs during LOGO storms from a device. */ ndlp->nlp_flag |= NLP_LOGO_ACC; - lpfc_els_rsp_acc(phba, ELS_CMD_ACC, cmdiocb, ndlp, NULL, 0); + if (els_cmd == ELS_CMD_PRLO) + lpfc_els_rsp_acc(phba, ELS_CMD_PRLO, cmdiocb, ndlp, NULL, 0); + else + lpfc_els_rsp_acc(phba, ELS_CMD_ACC, cmdiocb, ndlp, NULL, 0); if (!(ndlp->nlp_type & NLP_FABRIC) || (ndlp->nlp_state == NLP_STE_ADISC_ISSUE)) { @@ -681,7 +685,7 @@ lpfc_rcv_logo_plogi_issue(struct lpfc_hba * phba, /* software abort outstanding PLOGI */ lpfc_els_abort(phba, ndlp, 1); - lpfc_rcv_logo(phba, ndlp, cmdiocb); + lpfc_rcv_logo(phba, ndlp, cmdiocb, ELS_CMD_LOGO); return ndlp->nlp_state; } @@ -788,10 +792,6 @@ lpfc_cmpl_plogi_plogi_issue(struct lpfc_hba * phba, if (lpfc_reg_login (phba, irsp->un.elsreq64.remoteID, (uint8_t *) sp, mbox, 0) == 0) { - /* set_slim mailbox command needs to - * execute first, queue this command to - * be processed later. - */ switch (ndlp->nlp_DID) { case NameServer_DID: mbox->mbox_cmpl = @@ -832,11 +832,17 @@ static uint32_t lpfc_device_rm_plogi_issue(struct lpfc_hba * phba, struct lpfc_nodelist * ndlp, void *arg, uint32_t evt) { - /* software abort outstanding PLOGI */ - lpfc_els_abort(phba, ndlp, 1); + if(ndlp->nlp_flag & NLP_NPR_2B_DISC) { + ndlp->nlp_flag |= NLP_NODEV_REMOVE; + return ndlp->nlp_state; + } + else { + /* software abort outstanding PLOGI */ + lpfc_els_abort(phba, ndlp, 1); - lpfc_nlp_list(phba, ndlp, NLP_NO_LIST); - return NLP_STE_FREED_NODE; + lpfc_nlp_list(phba, ndlp, NLP_NO_LIST); + return NLP_STE_FREED_NODE; + } } static uint32_t @@ -851,7 +857,7 @@ lpfc_device_recov_plogi_issue(struct lpfc_hba * phba, ndlp->nlp_state = NLP_STE_NPR_NODE; lpfc_nlp_list(phba, ndlp, NLP_NPR_LIST); spin_lock_irq(phba->host->host_lock); - ndlp->nlp_flag &= ~NLP_NPR_2B_DISC; + ndlp->nlp_flag &= ~(NLP_NODEV_REMOVE | NLP_NPR_2B_DISC); spin_unlock_irq(phba->host->host_lock); return ndlp->nlp_state; @@ -905,7 +911,7 @@ lpfc_rcv_logo_adisc_issue(struct lpfc_hba * phba, /* software abort outstanding ADISC */ lpfc_els_abort(phba, ndlp, 0); - lpfc_rcv_logo(phba, ndlp, cmdiocb); + lpfc_rcv_logo(phba, ndlp, cmdiocb, ELS_CMD_LOGO); return ndlp->nlp_state; } @@ -932,7 +938,7 @@ lpfc_rcv_prlo_adisc_issue(struct lpfc_hba * phba, cmdiocb = (struct lpfc_iocbq *) arg; /* Treat like rcv logo */ - lpfc_rcv_logo(phba, ndlp, cmdiocb); + lpfc_rcv_logo(phba, ndlp, cmdiocb, ELS_CMD_PRLO); return ndlp->nlp_state; } @@ -987,11 +993,17 @@ lpfc_device_rm_adisc_issue(struct lpfc_hba * phba, struct lpfc_nodelist * ndlp, void *arg, uint32_t evt) { - /* software abort outstanding ADISC */ - lpfc_els_abort(phba, ndlp, 1); + if(ndlp->nlp_flag & NLP_NPR_2B_DISC) { + ndlp->nlp_flag |= NLP_NODEV_REMOVE; + return ndlp->nlp_state; + } + else { + /* software abort outstanding ADISC */ + lpfc_els_abort(phba, ndlp, 1); - lpfc_nlp_list(phba, ndlp, NLP_NO_LIST); - return NLP_STE_FREED_NODE; + lpfc_nlp_list(phba, ndlp, NLP_NO_LIST); + return NLP_STE_FREED_NODE; + } } static uint32_t @@ -1006,7 +1018,7 @@ lpfc_device_recov_adisc_issue(struct lpfc_hba * phba, ndlp->nlp_state = NLP_STE_NPR_NODE; lpfc_nlp_list(phba, ndlp, NLP_NPR_LIST); spin_lock_irq(phba->host->host_lock); - ndlp->nlp_flag &= ~NLP_NPR_2B_DISC; + ndlp->nlp_flag &= ~(NLP_NODEV_REMOVE | NLP_NPR_2B_DISC); ndlp->nlp_flag |= NLP_NPR_ADISC; spin_unlock_irq(phba->host->host_lock); @@ -1048,7 +1060,7 @@ lpfc_rcv_logo_reglogin_issue(struct lpfc_hba * phba, cmdiocb = (struct lpfc_iocbq *) arg; - lpfc_rcv_logo(phba, ndlp, cmdiocb); + lpfc_rcv_logo(phba, ndlp, cmdiocb, ELS_CMD_LOGO); return ndlp->nlp_state; } @@ -1073,7 +1085,7 @@ lpfc_rcv_prlo_reglogin_issue(struct lpfc_hba * phba, struct lpfc_iocbq *cmdiocb; cmdiocb = (struct lpfc_iocbq *) arg; - lpfc_els_rsp_acc(phba, ELS_CMD_ACC, cmdiocb, ndlp, NULL, 0); + lpfc_els_rsp_acc(phba, ELS_CMD_PRLO, cmdiocb, ndlp, NULL, 0); return ndlp->nlp_state; } @@ -1133,8 +1145,14 @@ lpfc_device_rm_reglogin_issue(struct lpfc_hba * phba, struct lpfc_nodelist * ndlp, void *arg, uint32_t evt) { - lpfc_nlp_list(phba, ndlp, NLP_NO_LIST); - return NLP_STE_FREED_NODE; + if(ndlp->nlp_flag & NLP_NPR_2B_DISC) { + ndlp->nlp_flag |= NLP_NODEV_REMOVE; + return ndlp->nlp_state; + } + else { + lpfc_nlp_list(phba, ndlp, NLP_NO_LIST); + return NLP_STE_FREED_NODE; + } } static uint32_t @@ -1146,7 +1164,7 @@ lpfc_device_recov_reglogin_issue(struct lpfc_hba * phba, ndlp->nlp_state = NLP_STE_NPR_NODE; lpfc_nlp_list(phba, ndlp, NLP_NPR_LIST); spin_lock_irq(phba->host->host_lock); - ndlp->nlp_flag &= ~NLP_NPR_2B_DISC; + ndlp->nlp_flag &= ~(NLP_NODEV_REMOVE | NLP_NPR_2B_DISC); spin_unlock_irq(phba->host->host_lock); return ndlp->nlp_state; } @@ -1186,7 +1204,7 @@ lpfc_rcv_logo_prli_issue(struct lpfc_hba * phba, /* Software abort outstanding PRLI before sending acc */ lpfc_els_abort(phba, ndlp, 1); - lpfc_rcv_logo(phba, ndlp, cmdiocb); + lpfc_rcv_logo(phba, ndlp, cmdiocb, ELS_CMD_LOGO); return ndlp->nlp_state; } @@ -1214,7 +1232,7 @@ lpfc_rcv_prlo_prli_issue(struct lpfc_hba * phba, struct lpfc_iocbq *cmdiocb; cmdiocb = (struct lpfc_iocbq *) arg; - lpfc_els_rsp_acc(phba, ELS_CMD_ACC, cmdiocb, ndlp, NULL, 0); + lpfc_els_rsp_acc(phba, ELS_CMD_PRLO, cmdiocb, ndlp, NULL, 0); return ndlp->nlp_state; } @@ -1278,11 +1296,17 @@ static uint32_t lpfc_device_rm_prli_issue(struct lpfc_hba * phba, struct lpfc_nodelist * ndlp, void *arg, uint32_t evt) { - /* software abort outstanding PRLI */ - lpfc_els_abort(phba, ndlp, 1); + if(ndlp->nlp_flag & NLP_NPR_2B_DISC) { + ndlp->nlp_flag |= NLP_NODEV_REMOVE; + return ndlp->nlp_state; + } + else { + /* software abort outstanding PLOGI */ + lpfc_els_abort(phba, ndlp, 1); - lpfc_nlp_list(phba, ndlp, NLP_NO_LIST); - return NLP_STE_FREED_NODE; + lpfc_nlp_list(phba, ndlp, NLP_NO_LIST); + return NLP_STE_FREED_NODE; + } } @@ -1313,7 +1337,7 @@ lpfc_device_recov_prli_issue(struct lpfc_hba * phba, ndlp->nlp_state = NLP_STE_NPR_NODE; lpfc_nlp_list(phba, ndlp, NLP_NPR_LIST); spin_lock_irq(phba->host->host_lock); - ndlp->nlp_flag &= ~NLP_NPR_2B_DISC; + ndlp->nlp_flag &= ~(NLP_NODEV_REMOVE | NLP_NPR_2B_DISC); spin_unlock_irq(phba->host->host_lock); return ndlp->nlp_state; } @@ -1351,7 +1375,7 @@ lpfc_rcv_logo_unmap_node(struct lpfc_hba * phba, cmdiocb = (struct lpfc_iocbq *) arg; - lpfc_rcv_logo(phba, ndlp, cmdiocb); + lpfc_rcv_logo(phba, ndlp, cmdiocb, ELS_CMD_LOGO); return ndlp->nlp_state; } @@ -1375,7 +1399,7 @@ lpfc_rcv_prlo_unmap_node(struct lpfc_hba * phba, cmdiocb = (struct lpfc_iocbq *) arg; - lpfc_els_rsp_acc(phba, ELS_CMD_ACC, cmdiocb, ndlp, NULL, 0); + lpfc_els_rsp_acc(phba, ELS_CMD_PRLO, cmdiocb, ndlp, NULL, 0); return ndlp->nlp_state; } @@ -1386,7 +1410,7 @@ lpfc_device_recov_unmap_node(struct lpfc_hba * phba, ndlp->nlp_prev_state = NLP_STE_UNMAPPED_NODE; ndlp->nlp_state = NLP_STE_NPR_NODE; lpfc_nlp_list(phba, ndlp, NLP_NPR_LIST); - ndlp->nlp_flag &= ~NLP_NPR_2B_DISC; + ndlp->nlp_flag &= ~(NLP_NODEV_REMOVE | NLP_NPR_2B_DISC); lpfc_disc_set_adisc(phba, ndlp); return ndlp->nlp_state; @@ -1424,7 +1448,7 @@ lpfc_rcv_logo_mapped_node(struct lpfc_hba * phba, cmdiocb = (struct lpfc_iocbq *) arg; - lpfc_rcv_logo(phba, ndlp, cmdiocb); + lpfc_rcv_logo(phba, ndlp, cmdiocb, ELS_CMD_LOGO); return ndlp->nlp_state; } @@ -1456,7 +1480,7 @@ lpfc_rcv_prlo_mapped_node(struct lpfc_hba * phba, spin_unlock_irq(phba->host->host_lock); /* Treat like rcv logo */ - lpfc_rcv_logo(phba, ndlp, cmdiocb); + lpfc_rcv_logo(phba, ndlp, cmdiocb, ELS_CMD_PRLO); return ndlp->nlp_state; } @@ -1469,7 +1493,7 @@ lpfc_device_recov_mapped_node(struct lpfc_hba * phba, ndlp->nlp_state = NLP_STE_NPR_NODE; lpfc_nlp_list(phba, ndlp, NLP_NPR_LIST); spin_lock_irq(phba->host->host_lock); - ndlp->nlp_flag &= ~NLP_NPR_2B_DISC; + ndlp->nlp_flag &= ~(NLP_NODEV_REMOVE | NLP_NPR_2B_DISC); spin_unlock_irq(phba->host->host_lock); lpfc_disc_set_adisc(phba, ndlp); return ndlp->nlp_state; @@ -1551,7 +1575,7 @@ lpfc_rcv_logo_npr_node(struct lpfc_hba * phba, cmdiocb = (struct lpfc_iocbq *) arg; - lpfc_rcv_logo(phba, ndlp, cmdiocb); + lpfc_rcv_logo(phba, ndlp, cmdiocb, ELS_CMD_LOGO); return ndlp->nlp_state; } @@ -1617,9 +1641,16 @@ lpfc_cmpl_plogi_npr_node(struct lpfc_hba * phba, struct lpfc_nodelist * ndlp, void *arg, uint32_t evt) { struct lpfc_iocbq *cmdiocb, *rspiocb; + IOCB_t *irsp; cmdiocb = (struct lpfc_iocbq *) arg; rspiocb = cmdiocb->context_un.rsp_iocb; + + irsp = &rspiocb->iocb; + if (irsp->ulpStatus) { + lpfc_nlp_list(phba, ndlp, NLP_NO_LIST); + return NLP_STE_FREED_NODE; + } return ndlp->nlp_state; } @@ -1628,9 +1659,16 @@ lpfc_cmpl_prli_npr_node(struct lpfc_hba * phba, struct lpfc_nodelist * ndlp, void *arg, uint32_t evt) { struct lpfc_iocbq *cmdiocb, *rspiocb; + IOCB_t *irsp; cmdiocb = (struct lpfc_iocbq *) arg; rspiocb = cmdiocb->context_un.rsp_iocb; + + irsp = &rspiocb->iocb; + if (irsp->ulpStatus && (ndlp->nlp_flag & NLP_NODEV_REMOVE)) { + lpfc_nlp_list(phba, ndlp, NLP_NO_LIST); + return NLP_STE_FREED_NODE; + } return ndlp->nlp_state; } @@ -1649,9 +1687,16 @@ lpfc_cmpl_adisc_npr_node(struct lpfc_hba * phba, uint32_t evt) { struct lpfc_iocbq *cmdiocb, *rspiocb; + IOCB_t *irsp; cmdiocb = (struct lpfc_iocbq *) arg; rspiocb = cmdiocb->context_un.rsp_iocb; + + irsp = &rspiocb->iocb; + if (irsp->ulpStatus && (ndlp->nlp_flag & NLP_NODEV_REMOVE)) { + lpfc_nlp_list(phba, ndlp, NLP_NO_LIST); + return NLP_STE_FREED_NODE; + } return ndlp->nlp_state; } @@ -1668,7 +1713,12 @@ lpfc_cmpl_reglogin_npr_node(struct lpfc_hba * phba, if (!mb->mbxStatus) ndlp->nlp_rpi = mb->un.varWords[0]; - + else { + if (ndlp->nlp_flag & NLP_NODEV_REMOVE) { + lpfc_nlp_list(phba, ndlp, NLP_NO_LIST); + return NLP_STE_FREED_NODE; + } + } return ndlp->nlp_state; } @@ -1677,6 +1727,10 @@ lpfc_device_rm_npr_node(struct lpfc_hba * phba, struct lpfc_nodelist * ndlp, void *arg, uint32_t evt) { + if (ndlp->nlp_flag & NLP_NPR_2B_DISC) { + ndlp->nlp_flag |= NLP_NODEV_REMOVE; + return ndlp->nlp_state; + } lpfc_nlp_list(phba, ndlp, NLP_NO_LIST); return NLP_STE_FREED_NODE; } @@ -1687,7 +1741,7 @@ lpfc_device_recov_npr_node(struct lpfc_hba * phba, uint32_t evt) { spin_lock_irq(phba->host->host_lock); - ndlp->nlp_flag &= ~NLP_NPR_2B_DISC; + ndlp->nlp_flag &= ~(NLP_NODEV_REMOVE | NLP_NPR_2B_DISC); spin_unlock_irq(phba->host->host_lock); if (ndlp->nlp_flag & NLP_DELAY_TMO) { lpfc_cancel_retry_delay_tmo(phba, ndlp); diff --git a/drivers/scsi/lpfc/lpfc_scsi.c b/drivers/scsi/lpfc/lpfc_scsi.c index f9379987372..7dc4c2e6bed 100644 --- a/drivers/scsi/lpfc/lpfc_scsi.c +++ b/drivers/scsi/lpfc/lpfc_scsi.c @@ -629,8 +629,7 @@ lpfc_scsi_prep_task_mgmt_cmd(struct lpfc_hba *phba, struct lpfc_iocbq *piocbq; IOCB_t *piocb; struct fcp_cmnd *fcp_cmnd; - struct scsi_device *scsi_dev = lpfc_cmd->pCmd->device; - struct lpfc_rport_data *rdata = scsi_dev->hostdata; + struct lpfc_rport_data *rdata = lpfc_cmd->rdata; struct lpfc_nodelist *ndlp = rdata->pnode; if ((ndlp == NULL) || (ndlp->nlp_state != NLP_STE_MAPPED_NODE)) { @@ -665,56 +664,18 @@ lpfc_scsi_prep_task_mgmt_cmd(struct lpfc_hba *phba, piocb->ulpTimeout = lpfc_cmd->timeout; } - lpfc_cmd->rdata = rdata; - - switch (task_mgmt_cmd) { - case FCP_LUN_RESET: - /* Issue LUN Reset to TGT <num> LUN <num> */ - lpfc_printf_log(phba, - KERN_INFO, - LOG_FCP, - "%d:0703 Issue LUN Reset to TGT %d LUN %d " - "Data: x%x x%x\n", - phba->brd_no, - scsi_dev->id, scsi_dev->lun, - ndlp->nlp_rpi, ndlp->nlp_flag); - - break; - case FCP_ABORT_TASK_SET: - /* Issue Abort Task Set to TGT <num> LUN <num> */ - lpfc_printf_log(phba, - KERN_INFO, - LOG_FCP, - "%d:0701 Issue Abort Task Set to TGT %d LUN %d " - "Data: x%x x%x\n", - phba->brd_no, - scsi_dev->id, scsi_dev->lun, - ndlp->nlp_rpi, ndlp->nlp_flag); - - break; - case FCP_TARGET_RESET: - /* Issue Target Reset to TGT <num> */ - lpfc_printf_log(phba, - KERN_INFO, - LOG_FCP, - "%d:0702 Issue Target Reset to TGT %d " - "Data: x%x x%x\n", - phba->brd_no, - scsi_dev->id, ndlp->nlp_rpi, - ndlp->nlp_flag); - break; - } - return (1); } static int -lpfc_scsi_tgt_reset(struct lpfc_scsi_buf * lpfc_cmd, struct lpfc_hba * phba) +lpfc_scsi_tgt_reset(struct lpfc_scsi_buf * lpfc_cmd, struct lpfc_hba * phba, + unsigned tgt_id, struct lpfc_rport_data *rdata) { struct lpfc_iocbq *iocbq; struct lpfc_iocbq *iocbqrsp; int ret; + lpfc_cmd->rdata = rdata; ret = lpfc_scsi_prep_task_mgmt_cmd(phba, lpfc_cmd, FCP_TARGET_RESET); if (!ret) return FAILED; @@ -726,6 +687,13 @@ lpfc_scsi_tgt_reset(struct lpfc_scsi_buf * lpfc_cmd, struct lpfc_hba * phba) if (!iocbqrsp) return FAILED; + /* Issue Target Reset to TGT <num> */ + lpfc_printf_log(phba, KERN_INFO, LOG_FCP, + "%d:0702 Issue Target Reset to TGT %d " + "Data: x%x x%x\n", + phba->brd_no, tgt_id, rdata->pnode->nlp_rpi, + rdata->pnode->nlp_flag); + ret = lpfc_sli_issue_iocb_wait(phba, &phba->sli.ring[phba->sli.fcp_ring], iocbq, iocbqrsp, lpfc_cmd->timeout); @@ -1021,6 +989,7 @@ lpfc_reset_lun_handler(struct scsi_cmnd *cmnd) lpfc_cmd->pCmd = cmnd; lpfc_cmd->timeout = 60; lpfc_cmd->scsi_hba = phba; + lpfc_cmd->rdata = rdata; ret = lpfc_scsi_prep_task_mgmt_cmd(phba, lpfc_cmd, FCP_LUN_RESET); if (!ret) @@ -1033,6 +1002,11 @@ lpfc_reset_lun_handler(struct scsi_cmnd *cmnd) if (iocbqrsp == NULL) goto out_free_scsi_buf; + lpfc_printf_log(phba, KERN_INFO, LOG_FCP, + "%d:0703 Issue LUN Reset to TGT %d LUN %d " + "Data: x%x x%x\n", phba->brd_no, cmnd->device->id, + cmnd->device->lun, pnode->nlp_rpi, pnode->nlp_flag); + ret = lpfc_sli_issue_iocb_wait(phba, &phba->sli.ring[phba->sli.fcp_ring], iocbq, iocbqrsp, lpfc_cmd->timeout); @@ -1104,7 +1078,6 @@ lpfc_reset_bus_handler(struct scsi_cmnd *cmnd) int match; int ret = FAILED, i, err_count = 0; int cnt, loopcnt; - unsigned int midlayer_id = 0; struct lpfc_scsi_buf * lpfc_cmd; lpfc_block_requests(phba); @@ -1124,7 +1097,6 @@ lpfc_reset_bus_handler(struct scsi_cmnd *cmnd) * targets known to the driver. Should any target reset * fail, this routine returns failure to the midlayer. */ - midlayer_id = cmnd->device->id; for (i = 0; i < MAX_FCP_TARGET; i++) { /* Search the mapped list for this target ID */ match = 0; @@ -1137,9 +1109,8 @@ lpfc_reset_bus_handler(struct scsi_cmnd *cmnd) if (!match) continue; - lpfc_cmd->pCmd->device->id = i; - lpfc_cmd->pCmd->device->hostdata = ndlp->rport->dd_data; - ret = lpfc_scsi_tgt_reset(lpfc_cmd, phba); + ret = lpfc_scsi_tgt_reset(lpfc_cmd, phba, + i, ndlp->rport->dd_data); if (ret != SUCCESS) { lpfc_printf_log(phba, KERN_ERR, LOG_FCP, "%d:0713 Bus Reset on target %d failed\n", @@ -1158,7 +1129,6 @@ lpfc_reset_bus_handler(struct scsi_cmnd *cmnd) * the targets. Unfortunately, some targets do not abide by * this forcing the driver to double check. */ - cmnd->device->id = midlayer_id; cnt = lpfc_sli_sum_iocb(phba, &phba->sli.ring[phba->sli.fcp_ring], 0, 0, LPFC_CTX_HOST); if (cnt) diff --git a/drivers/scsi/lpfc/lpfc_version.h b/drivers/scsi/lpfc/lpfc_version.h index 4cf1366108b..6b737568b83 100644 --- a/drivers/scsi/lpfc/lpfc_version.h +++ b/drivers/scsi/lpfc/lpfc_version.h @@ -18,7 +18,7 @@ * included with this package. * *******************************************************************/ -#define LPFC_DRIVER_VERSION "8.1.4" +#define LPFC_DRIVER_VERSION "8.1.6" #define LPFC_DRIVER_NAME "lpfc" diff --git a/drivers/scsi/megaraid.c b/drivers/scsi/megaraid.c index 80b68a2481b..de35ffe2f79 100644 --- a/drivers/scsi/megaraid.c +++ b/drivers/scsi/megaraid.c @@ -4471,7 +4471,6 @@ mega_internal_command(adapter_t *adapter, megacmd_t *mc, mega_passthru *pthru) { Scsi_Cmnd *scmd; struct scsi_device *sdev; - unsigned long flags = 0; scb_t *scb; int rval; diff --git a/drivers/scsi/megaraid/megaraid_mbox.c b/drivers/scsi/megaraid/megaraid_mbox.c index c11e5ce6865..bec1424eda8 100644 --- a/drivers/scsi/megaraid/megaraid_mbox.c +++ b/drivers/scsi/megaraid/megaraid_mbox.c @@ -10,7 +10,7 @@ * 2 of the License, or (at your option) any later version. * * FILE : megaraid_mbox.c - * Version : v2.20.4.7 (Nov 14 2005) + * Version : v2.20.4.8 (Apr 11 2006) * * Authors: * Atul Mukker <Atul.Mukker@lsil.com> @@ -2278,6 +2278,7 @@ megaraid_mbox_dpc(unsigned long devp) unsigned long flags; uint8_t c; int status; + uioc_t *kioc; if (!adapter) return; @@ -2320,6 +2321,9 @@ megaraid_mbox_dpc(unsigned long devp) // remove from local clist list_del_init(&scb->list); + kioc = (uioc_t *)scb->gp; + kioc->status = 0; + megaraid_mbox_mm_done(adapter, scb); continue; @@ -2636,6 +2640,7 @@ megaraid_reset_handler(struct scsi_cmnd *scp) int recovery_window; int recovering; int i; + uioc_t *kioc; adapter = SCP2ADAPTER(scp); raid_dev = ADAP2RAIDDEV(adapter); @@ -2655,32 +2660,51 @@ megaraid_reset_handler(struct scsi_cmnd *scp) // Also, reset all the commands currently owned by the driver spin_lock_irqsave(PENDING_LIST_LOCK(adapter), flags); list_for_each_entry_safe(scb, tmp, &adapter->pend_list, list) { - list_del_init(&scb->list); // from pending list - con_log(CL_ANN, (KERN_WARNING - "megaraid: %ld:%d[%d:%d], reset from pending list\n", - scp->serial_number, scb->sno, - scb->dev_channel, scb->dev_target)); + if (scb->sno >= MBOX_MAX_SCSI_CMDS) { + con_log(CL_ANN, (KERN_WARNING + "megaraid: IOCTL packet with %d[%d:%d] being reset\n", + scb->sno, scb->dev_channel, scb->dev_target)); - scp->result = (DID_RESET << 16); - scp->scsi_done(scp); + scb->status = -1; - megaraid_dealloc_scb(adapter, scb); + kioc = (uioc_t *)scb->gp; + kioc->status = -EFAULT; + + megaraid_mbox_mm_done(adapter, scb); + } else { + if (scb->scp == scp) { // Found command + con_log(CL_ANN, (KERN_WARNING + "megaraid: %ld:%d[%d:%d], reset from pending list\n", + scp->serial_number, scb->sno, + scb->dev_channel, scb->dev_target)); + } else { + con_log(CL_ANN, (KERN_WARNING + "megaraid: IO packet with %d[%d:%d] being reset\n", + scb->sno, scb->dev_channel, scb->dev_target)); + } + + scb->scp->result = (DID_RESET << 16); + scb->scp->scsi_done(scb->scp); + + megaraid_dealloc_scb(adapter, scb); + } } spin_unlock_irqrestore(PENDING_LIST_LOCK(adapter), flags); if (adapter->outstanding_cmds) { con_log(CL_ANN, (KERN_NOTICE "megaraid: %d outstanding commands. Max wait %d sec\n", - adapter->outstanding_cmds, MBOX_RESET_WAIT)); + adapter->outstanding_cmds, + (MBOX_RESET_WAIT + MBOX_RESET_EXT_WAIT))); } recovery_window = MBOX_RESET_WAIT + MBOX_RESET_EXT_WAIT; recovering = adapter->outstanding_cmds; - for (i = 0; i < recovery_window && adapter->outstanding_cmds; i++) { + for (i = 0; i < recovery_window; i++) { megaraid_ack_sequence(adapter); @@ -2689,12 +2713,11 @@ megaraid_reset_handler(struct scsi_cmnd *scp) con_log(CL_ANN, ( "megaraid mbox: Wait for %d commands to complete:%d\n", adapter->outstanding_cmds, - MBOX_RESET_WAIT - i)); + (MBOX_RESET_WAIT + MBOX_RESET_EXT_WAIT) - i)); } // bailout if no recovery happended in reset time - if ((i == MBOX_RESET_WAIT) && - (recovering == adapter->outstanding_cmds)) { + if (adapter->outstanding_cmds == 0) { break; } @@ -2918,12 +2941,13 @@ mbox_post_sync_cmd_fast(adapter_t *adapter, uint8_t raw_mbox[]) wmb(); WRINDOOR(raid_dev, raid_dev->mbox_dma | 0x1); - for (i = 0; i < 0xFFFFF; i++) { + for (i = 0; i < MBOX_SYNC_WAIT_CNT; i++) { if (mbox->numstatus != 0xFF) break; rmb(); + udelay(MBOX_SYNC_DELAY_200); } - if (i == 0xFFFFF) { + if (i == MBOX_SYNC_WAIT_CNT) { // We may need to re-calibrate the counter con_log(CL_ANN, (KERN_CRIT "megaraid: fast sync command timed out\n")); @@ -3475,7 +3499,7 @@ megaraid_cmm_register(adapter_t *adapter) adp.drvr_data = (unsigned long)adapter; adp.pdev = adapter->pdev; adp.issue_uioc = megaraid_mbox_mm_handler; - adp.timeout = 300; + adp.timeout = MBOX_RESET_WAIT + MBOX_RESET_EXT_WAIT; adp.max_kioc = MBOX_MAX_USER_CMDS; if ((rval = mraid_mm_register_adp(&adp)) != 0) { @@ -3702,7 +3726,6 @@ megaraid_mbox_mm_done(adapter_t *adapter, scb_t *scb) unsigned long flags; kioc = (uioc_t *)scb->gp; - kioc->status = 0; mbox64 = (mbox64_t *)(unsigned long)kioc->cmdbuf; mbox64->mbox32.status = scb->status; raw_mbox = (uint8_t *)&mbox64->mbox32; diff --git a/drivers/scsi/megaraid/megaraid_mbox.h b/drivers/scsi/megaraid/megaraid_mbox.h index 882fb1a0b57..868fb0ec93e 100644 --- a/drivers/scsi/megaraid/megaraid_mbox.h +++ b/drivers/scsi/megaraid/megaraid_mbox.h @@ -21,8 +21,8 @@ #include "megaraid_ioctl.h" -#define MEGARAID_VERSION "2.20.4.7" -#define MEGARAID_EXT_VERSION "(Release Date: Mon Nov 14 12:27:22 EST 2005)" +#define MEGARAID_VERSION "2.20.4.8" +#define MEGARAID_EXT_VERSION "(Release Date: Mon Apr 11 12:27:22 EST 2006)" /* @@ -100,6 +100,9 @@ #define MBOX_BUSY_WAIT 10 // max usec to wait for busy mailbox #define MBOX_RESET_WAIT 180 // wait these many seconds in reset #define MBOX_RESET_EXT_WAIT 120 // extended wait reset +#define MBOX_SYNC_WAIT_CNT 0xFFFF // wait loop index for synchronous mode + +#define MBOX_SYNC_DELAY_200 200 // 200 micro-seconds /* * maximum transfer that can happen through the firmware commands issued diff --git a/drivers/scsi/megaraid/megaraid_mm.c b/drivers/scsi/megaraid/megaraid_mm.c index 8f3ce043229..e8f534fb336 100644 --- a/drivers/scsi/megaraid/megaraid_mm.c +++ b/drivers/scsi/megaraid/megaraid_mm.c @@ -898,10 +898,8 @@ mraid_mm_register_adp(mraid_mmadp_t *lld_adp) adapter = kmalloc(sizeof(mraid_mmadp_t), GFP_KERNEL); - if (!adapter) { - rval = -ENOMEM; - goto memalloc_error; - } + if (!adapter) + return -ENOMEM; memset(adapter, 0, sizeof(mraid_mmadp_t)); diff --git a/drivers/scsi/qla2xxx/qla_os.c b/drivers/scsi/qla2xxx/qla_os.c index 017729c59a4..584fe5d8e50 100644 --- a/drivers/scsi/qla2xxx/qla_os.c +++ b/drivers/scsi/qla2xxx/qla_os.c @@ -599,6 +599,7 @@ qla2x00_wait_for_loop_ready(scsi_qla_host_t *ha) * Either SUCCESS or FAILED. * * Note: +* Only return FAILED if command not returned by firmware. **************************************************************************/ int qla2xxx_eh_abort(struct scsi_cmnd *cmd) @@ -609,11 +610,12 @@ qla2xxx_eh_abort(struct scsi_cmnd *cmd) unsigned int id, lun; unsigned long serial; unsigned long flags; + int wait = 0; if (!CMD_SP(cmd)) - return FAILED; + return SUCCESS; - ret = FAILED; + ret = SUCCESS; id = cmd->device->id; lun = cmd->device->lun; @@ -642,7 +644,7 @@ qla2xxx_eh_abort(struct scsi_cmnd *cmd) } else { DEBUG3(printk("%s(%ld): abort_command " "mbx success.\n", __func__, ha->host_no)); - ret = SUCCESS; + wait = 1; } spin_lock_irqsave(&ha->hardware_lock, flags); @@ -651,17 +653,18 @@ qla2xxx_eh_abort(struct scsi_cmnd *cmd) spin_unlock_irqrestore(&ha->hardware_lock, flags); /* Wait for the command to be returned. */ - if (ret == SUCCESS) { + if (wait) { if (qla2x00_eh_wait_on_command(ha, cmd) != QLA_SUCCESS) { qla_printk(KERN_ERR, ha, "scsi(%ld:%d:%d): Abort handler timed out -- %lx " "%x.\n", ha->host_no, id, lun, serial, ret); + ret = FAILED; } } qla_printk(KERN_INFO, ha, - "scsi(%ld:%d:%d): Abort command issued -- %lx %x.\n", ha->host_no, - id, lun, serial, ret); + "scsi(%ld:%d:%d): Abort command issued -- %d %lx %x.\n", + ha->host_no, id, lun, wait, serial, ret); return ret; } @@ -1700,8 +1703,8 @@ qla2x00_free_device(scsi_qla_host_t *ha) ha->flags.online = 0; /* Detach interrupts */ - if (ha->pdev->irq) - free_irq(ha->pdev->irq, ha); + if (ha->host->irq) + free_irq(ha->host->irq, ha); /* release io space registers */ if (ha->iobase) diff --git a/drivers/scsi/scsi_devinfo.c b/drivers/scsi/scsi_devinfo.c index c750d3399a9..941c1e15c89 100644 --- a/drivers/scsi/scsi_devinfo.c +++ b/drivers/scsi/scsi_devinfo.c @@ -56,6 +56,8 @@ static struct { {"DENON", "DRD-25X", "V", BLIST_NOLUN}, /* locks up */ {"HITACHI", "DK312C", "CM81", BLIST_NOLUN}, /* responds to all lun */ {"HITACHI", "DK314C", "CR21", BLIST_NOLUN}, /* responds to all lun */ + {"IBM", "2104-DU3", NULL, BLIST_NOLUN}, /* locks up */ + {"IBM", "2104-TU3", NULL, BLIST_NOLUN}, /* locks up */ {"IMS", "CDD521/10", "2.06", BLIST_NOLUN}, /* locks up */ {"MAXTOR", "XT-3280", "PR02", BLIST_NOLUN}, /* locks up */ {"MAXTOR", "XT-4380S", "B3C", BLIST_NOLUN}, /* locks up */ diff --git a/drivers/scsi/scsi_lib.c b/drivers/scsi/scsi_lib.c index 7b0f9a3810d..764a8b375ea 100644 --- a/drivers/scsi/scsi_lib.c +++ b/drivers/scsi/scsi_lib.c @@ -1067,16 +1067,29 @@ void scsi_io_completion(struct scsi_cmnd *cmd, unsigned int good_bytes, break; case NOT_READY: /* - * If the device is in the process of becoming ready, - * retry. + * If the device is in the process of becoming + * ready, or has a temporary blockage, retry. */ - if (sshdr.asc == 0x04 && sshdr.ascq == 0x01) { - scsi_requeue_command(q, cmd); - return; + if (sshdr.asc == 0x04) { + switch (sshdr.ascq) { + case 0x01: /* becoming ready */ + case 0x04: /* format in progress */ + case 0x05: /* rebuild in progress */ + case 0x06: /* recalculation in progress */ + case 0x07: /* operation in progress */ + case 0x08: /* Long write in progress */ + case 0x09: /* self test in progress */ + scsi_requeue_command(q, cmd); + return; + default: + break; + } } - if (!(req->flags & REQ_QUIET)) + if (!(req->flags & REQ_QUIET)) { scmd_printk(KERN_INFO, cmd, - "Device not ready.\n"); + "Device not ready: "); + scsi_print_sense_hdr("", &sshdr); + } scsi_end_request(cmd, 0, this_count, 1); return; case VOLUME_OVERFLOW: diff --git a/drivers/scsi/sim710.c b/drivers/scsi/sim710.c index 3274ab76c8d..255886a9ac5 100644 --- a/drivers/scsi/sim710.c +++ b/drivers/scsi/sim710.c @@ -75,7 +75,7 @@ param_setup(char *str) else if(!strncmp(pos, "id:", 3)) { if(slot == -1) { printk(KERN_WARNING "sim710: Must specify slot for id parameter\n"); - } else if(slot > MAX_SLOTS) { + } else if(slot >= MAX_SLOTS) { printk(KERN_WARNING "sim710: Illegal slot %d for id %d\n", slot, val); } else { id_array[slot] = val; diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c index 674b15c78f6..bbf78aaf9e0 100644 --- a/drivers/serial/8250.c +++ b/drivers/serial/8250.c @@ -362,6 +362,40 @@ serial_out(struct uart_8250_port *up, int offset, int value) #define serial_inp(up, offset) serial_in(up, offset) #define serial_outp(up, offset, value) serial_out(up, offset, value) +/* Uart divisor latch read */ +static inline int _serial_dl_read(struct uart_8250_port *up) +{ + return serial_inp(up, UART_DLL) | serial_inp(up, UART_DLM) << 8; +} + +/* Uart divisor latch write */ +static inline void _serial_dl_write(struct uart_8250_port *up, int value) +{ + serial_outp(up, UART_DLL, value & 0xff); + serial_outp(up, UART_DLM, value >> 8 & 0xff); +} + +#ifdef CONFIG_SERIAL_8250_AU1X00 +/* Au1x00 haven't got a standard divisor latch */ +static int serial_dl_read(struct uart_8250_port *up) +{ + if (up->port.iotype == UPIO_AU) + return __raw_readl(up->port.membase + 0x28); + else + return _serial_dl_read(up); +} + +static void serial_dl_write(struct uart_8250_port *up, int value) +{ + if (up->port.iotype == UPIO_AU) + __raw_writel(value, up->port.membase + 0x28); + else + _serial_dl_write(up, value); +} +#else +#define serial_dl_read(up) _serial_dl_read(up) +#define serial_dl_write(up, value) _serial_dl_write(up, value) +#endif /* * For the 16C950 @@ -494,7 +528,8 @@ static void disable_rsa(struct uart_8250_port *up) */ static int size_fifo(struct uart_8250_port *up) { - unsigned char old_fcr, old_mcr, old_dll, old_dlm, old_lcr; + unsigned char old_fcr, old_mcr, old_lcr; + unsigned short old_dl; int count; old_lcr = serial_inp(up, UART_LCR); @@ -505,10 +540,8 @@ static int size_fifo(struct uart_8250_port *up) UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); serial_outp(up, UART_MCR, UART_MCR_LOOP); serial_outp(up, UART_LCR, UART_LCR_DLAB); - old_dll = serial_inp(up, UART_DLL); - old_dlm = serial_inp(up, UART_DLM); - serial_outp(up, UART_DLL, 0x01); - serial_outp(up, UART_DLM, 0x00); + old_dl = serial_dl_read(up); + serial_dl_write(up, 0x0001); serial_outp(up, UART_LCR, 0x03); for (count = 0; count < 256; count++) serial_outp(up, UART_TX, count); @@ -519,8 +552,7 @@ static int size_fifo(struct uart_8250_port *up) serial_outp(up, UART_FCR, old_fcr); serial_outp(up, UART_MCR, old_mcr); serial_outp(up, UART_LCR, UART_LCR_DLAB); - serial_outp(up, UART_DLL, old_dll); - serial_outp(up, UART_DLM, old_dlm); + serial_dl_write(up, old_dl); serial_outp(up, UART_LCR, old_lcr); return count; @@ -750,8 +782,7 @@ static void autoconfig_16550a(struct uart_8250_port *up) serial_outp(up, UART_LCR, 0xE0); - quot = serial_inp(up, UART_DLM) << 8; - quot += serial_inp(up, UART_DLL); + quot = serial_dl_read(up); quot <<= 3; status1 = serial_in(up, 0x04); /* EXCR1 */ @@ -759,8 +790,7 @@ static void autoconfig_16550a(struct uart_8250_port *up) status1 |= 0x10; /* 1.625 divisor for baud_base --> 921600 */ serial_outp(up, 0x04, status1); - serial_outp(up, UART_DLL, quot & 0xff); - serial_outp(up, UART_DLM, quot >> 8); + serial_dl_write(up, quot); serial_outp(up, UART_LCR, 0); @@ -1862,8 +1892,7 @@ serial8250_set_termios(struct uart_port *port, struct termios *termios, serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */ } - serial_outp(up, UART_DLL, quot & 0xff); /* LS of divisor */ - serial_outp(up, UART_DLM, quot >> 8); /* MS of divisor */ + serial_dl_write(up, quot); /* * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR @@ -1906,6 +1935,9 @@ static int serial8250_request_std_resource(struct uart_8250_port *up) int ret = 0; switch (up->port.iotype) { + case UPIO_AU: + size = 0x100000; + /* fall thru */ case UPIO_MEM: if (!up->port.mapbase) break; @@ -1938,6 +1970,9 @@ static void serial8250_release_std_resource(struct uart_8250_port *up) unsigned int size = 8 << up->port.regshift; switch (up->port.iotype) { + case UPIO_AU: + size = 0x100000; + /* fall thru */ case UPIO_MEM: if (!up->port.mapbase) break; @@ -2200,10 +2235,17 @@ static void serial8250_console_write(struct console *co, const char *s, unsigned int count) { struct uart_8250_port *up = &serial8250_ports[co->index]; + unsigned long flags; unsigned int ier; + int locked = 1; touch_nmi_watchdog(); + if (oops_in_progress) { + locked = spin_trylock_irqsave(&up->port.lock, flags); + } else + spin_lock_irqsave(&up->port.lock, flags); + /* * First save the IER then disable the interrupts */ @@ -2221,8 +2263,10 @@ serial8250_console_write(struct console *co, const char *s, unsigned int count) * and restore the IER */ wait_for_xmitr(up, BOTH_EMPTY); - up->ier |= UART_IER_THRI; - serial_out(up, UART_IER, ier | UART_IER_THRI); + serial_out(up, UART_IER, ier); + + if (locked) + spin_unlock_irqrestore(&up->port.lock, flags); } static int serial8250_console_setup(struct console *co, char *options) diff --git a/drivers/serial/8250_au1x00.c b/drivers/serial/8250_au1x00.c index 3d1bfd07208..58015fd14be 100644 --- a/drivers/serial/8250_au1x00.c +++ b/drivers/serial/8250_au1x00.c @@ -30,13 +30,12 @@ { \ .iobase = _base, \ .membase = (void __iomem *)_base,\ - .mapbase = _base, \ + .mapbase = CPHYSADDR(_base), \ .irq = _irq, \ .uartclk = 0, /* filled */ \ .regshift = 2, \ .iotype = UPIO_AU, \ - .flags = UPF_SKIP_TEST | \ - UPF_IOREMAP, \ + .flags = UPF_SKIP_TEST \ } static struct plat_serial8250_port au1x00_data[] = { diff --git a/drivers/serial/cpm_uart/cpm_uart.h b/drivers/serial/cpm_uart/cpm_uart.h index 73c8a088c16..3b35cb77953 100644 --- a/drivers/serial/cpm_uart/cpm_uart.h +++ b/drivers/serial/cpm_uart/cpm_uart.h @@ -5,11 +5,20 @@ * * Copyright (C) 2004 Freescale Semiconductor, Inc. * + * 2006 (c) MontaVista Software, Inc. + * Vitaly Bordug <vbordug@ru.mvista.com> + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + * */ #ifndef CPM_UART_H #define CPM_UART_H #include <linux/config.h> +#include <linux/platform_device.h> +#include <linux/fs_uart_pd.h> #if defined(CONFIG_CPM2) #include "cpm_uart_cpm2.h" @@ -26,14 +35,14 @@ #define FLAG_SMC 0x00000002 #define FLAG_CONSOLE 0x00000001 -#define UART_SMC1 0 -#define UART_SMC2 1 -#define UART_SCC1 2 -#define UART_SCC2 3 -#define UART_SCC3 4 -#define UART_SCC4 5 +#define UART_SMC1 fsid_smc1_uart +#define UART_SMC2 fsid_smc2_uart +#define UART_SCC1 fsid_scc1_uart +#define UART_SCC2 fsid_scc2_uart +#define UART_SCC3 fsid_scc3_uart +#define UART_SCC4 fsid_scc4_uart -#define UART_NR 6 +#define UART_NR fs_uart_nr #define RX_NUM_FIFO 4 #define RX_BUF_SIZE 32 @@ -64,6 +73,7 @@ struct uart_cpm_port { uint dp_addr; void *mem_addr; dma_addr_t dma_addr; + u32 mem_size; /* helpers */ int baud; int bits; @@ -90,4 +100,38 @@ void scc2_lineif(struct uart_cpm_port *pinfo); void scc3_lineif(struct uart_cpm_port *pinfo); void scc4_lineif(struct uart_cpm_port *pinfo); +/* + virtual to phys transtalion +*/ +static inline unsigned long cpu2cpm_addr(void* addr, struct uart_cpm_port *pinfo) +{ + int offset; + u32 val = (u32)addr; + /* sane check */ + if (likely((val >= (u32)pinfo->mem_addr)) && + (val<((u32)pinfo->mem_addr + pinfo->mem_size))) { + offset = val - (u32)pinfo->mem_addr; + return pinfo->dma_addr+offset; + } + /* something nasty happened */ + BUG(); + return 0; +} + +static inline void *cpm2cpu_addr(unsigned long addr, struct uart_cpm_port *pinfo) +{ + int offset; + u32 val = addr; + /* sane check */ + if (likely((val >= pinfo->dma_addr) && + (val<(pinfo->dma_addr + pinfo->mem_size)))) { + offset = val - (u32)pinfo->dma_addr; + return (void*)(pinfo->mem_addr+offset); + } + /* something nasty happened */ + BUG(); + return 0; +} + + #endif /* CPM_UART_H */ diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c index b7bf4c698a4..969f9490043 100644 --- a/drivers/serial/cpm_uart/cpm_uart_core.c +++ b/drivers/serial/cpm_uart/cpm_uart_core.c @@ -12,7 +12,8 @@ * * Copyright (C) 2004 Freescale Semiconductor, Inc. * (C) 2004 Intracom, S.A. - * (C) 2005 MontaVista Software, Inc. by Vitaly Bordug <vbordug@ru.mvista.com> + * (C) 2005-2006 MontaVista Software, Inc. + * Vitaly Bordug <vbordug@ru.mvista.com> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -41,6 +42,7 @@ #include <linux/device.h> #include <linux/bootmem.h> #include <linux/dma-mapping.h> +#include <linux/fs_uart_pd.h> #include <asm/io.h> #include <asm/irq.h> @@ -60,7 +62,7 @@ /* Track which ports are configured as uarts */ int cpm_uart_port_map[UART_NR]; /* How many ports did we config as uarts */ -int cpm_uart_nr; +int cpm_uart_nr = 0; /**************************************************************/ @@ -71,18 +73,51 @@ static void cpm_uart_initbd(struct uart_cpm_port *pinfo); /**************************************************************/ -static inline unsigned long cpu2cpm_addr(void *addr) + +/* Place-holder for board-specific stuff */ +struct platform_device* __attribute__ ((weak)) __init +early_uart_get_pdev(int index) +{ + return NULL; +} + + +static void cpm_uart_count(void) { - if ((unsigned long)addr >= CPM_ADDR) - return (unsigned long)addr; - return virt_to_bus(addr); + cpm_uart_nr = 0; +#ifdef CONFIG_SERIAL_CPM_SMC1 + cpm_uart_port_map[cpm_uart_nr++] = UART_SMC1; +#endif +#ifdef CONFIG_SERIAL_CPM_SMC2 + cpm_uart_port_map[cpm_uart_nr++] = UART_SMC2; +#endif +#ifdef CONFIG_SERIAL_CPM_SCC1 + cpm_uart_port_map[cpm_uart_nr++] = UART_SCC1; +#endif +#ifdef CONFIG_SERIAL_CPM_SCC2 + cpm_uart_port_map[cpm_uart_nr++] = UART_SCC2; +#endif +#ifdef CONFIG_SERIAL_CPM_SCC3 + cpm_uart_port_map[cpm_uart_nr++] = UART_SCC3; +#endif +#ifdef CONFIG_SERIAL_CPM_SCC4 + cpm_uart_port_map[cpm_uart_nr++] = UART_SCC4; +#endif } -static inline void *cpm2cpu_addr(unsigned long addr) +/* Get UART number by its id */ +static int cpm_uart_id2nr(int id) { - if (addr >= CPM_ADDR) - return (void *)addr; - return bus_to_virt(addr); + int i; + if (id < UART_NR) { + for (i=0; i<UART_NR; i++) { + if (cpm_uart_port_map[i] == id) + return i; + } + } + + /* not found or invalid argument */ + return -1; } /* @@ -258,7 +293,7 @@ static void cpm_uart_int_rx(struct uart_port *port, struct pt_regs *regs) } /* get pointer */ - cp = cpm2cpu_addr(bdp->cbd_bufaddr); + cp = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); /* loop through the buffer */ while (i-- > 0) { @@ -438,7 +473,11 @@ static void cpm_uart_shutdown(struct uart_port *port) } /* Shut them really down and reinit buffer descriptors */ - cpm_line_cr_cmd(line, CPM_CR_STOP_TX); + if (IS_SMC(pinfo)) + cpm_line_cr_cmd(line, CPM_CR_STOP_TX); + else + cpm_line_cr_cmd(line, CPM_CR_GRA_STOP_TX); + cpm_uart_initbd(pinfo); } } @@ -601,7 +640,7 @@ static int cpm_uart_tx_pump(struct uart_port *port) /* Pick next descriptor and fill from buffer */ bdp = pinfo->tx_cur; - p = cpm2cpu_addr(bdp->cbd_bufaddr); + p = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); *p++ = port->x_char; bdp->cbd_datlen = 1; @@ -628,7 +667,7 @@ static int cpm_uart_tx_pump(struct uart_port *port) while (!(bdp->cbd_sc & BD_SC_READY) && (xmit->tail != xmit->head)) { count = 0; - p = cpm2cpu_addr(bdp->cbd_bufaddr); + p = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); while (count < pinfo->tx_fifosize) { *p++ = xmit->buf[xmit->tail]; xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); @@ -677,12 +716,12 @@ static void cpm_uart_initbd(struct uart_cpm_port *pinfo) mem_addr = pinfo->mem_addr; bdp = pinfo->rx_cur = pinfo->rx_bd_base; for (i = 0; i < (pinfo->rx_nrfifos - 1); i++, bdp++) { - bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr); + bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo); bdp->cbd_sc = BD_SC_EMPTY | BD_SC_INTRPT; mem_addr += pinfo->rx_fifosize; } - bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr); + bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo); bdp->cbd_sc = BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT; /* Set the physical address of the host memory @@ -692,12 +731,12 @@ static void cpm_uart_initbd(struct uart_cpm_port *pinfo) mem_addr = pinfo->mem_addr + L1_CACHE_ALIGN(pinfo->rx_nrfifos * pinfo->rx_fifosize); bdp = pinfo->tx_cur = pinfo->tx_bd_base; for (i = 0; i < (pinfo->tx_nrfifos - 1); i++, bdp++) { - bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr); + bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo); bdp->cbd_sc = BD_SC_INTRPT; mem_addr += pinfo->tx_fifosize; } - bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr); + bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo); bdp->cbd_sc = BD_SC_WRAP | BD_SC_INTRPT; } @@ -829,14 +868,6 @@ static int cpm_uart_request_port(struct uart_port *port) if (pinfo->flags & FLAG_CONSOLE) return 0; - /* - * Setup any port IO, connect any baud rate generators, - * etc. This is expected to be handled by board - * dependant code - */ - if (pinfo->set_lineif) - pinfo->set_lineif(pinfo); - if (IS_SMC(pinfo)) { pinfo->smcp->smc_smcm &= ~(SMCM_RX | SMCM_TX); pinfo->smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); @@ -988,6 +1019,58 @@ struct uart_cpm_port cpm_uart_ports[UART_NR] = { }, }; +int cpm_uart_drv_get_platform_data(struct platform_device *pdev, int is_con) +{ + struct resource *r; + struct fs_uart_platform_info *pdata = pdev->dev.platform_data; + int idx = pdata->fs_no; /* It is UART_SMCx or UART_SCCx index */ + struct uart_cpm_port *pinfo; + int line; + u32 mem, pram; + + line = cpm_uart_id2nr(idx); + if(line < 0) { + printk(KERN_ERR"%s(): port %d is not registered", __FUNCTION__, idx); + return -1; + } + + pinfo = (struct uart_cpm_port *) &cpm_uart_ports[idx]; + + pinfo->brg = pdata->brg; + + if (!is_con) { + pinfo->port.line = line; + pinfo->port.flags = UPF_BOOT_AUTOCONF; + } + + if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs"))) + return -EINVAL; + mem = r->start; + + if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pram"))) + return -EINVAL; + pram = r->start; + + if(idx > fsid_smc2_uart) { + pinfo->sccp = (scc_t *)mem; + pinfo->sccup = (scc_uart_t *)pram; + } else { + pinfo->smcp = (smc_t *)mem; + pinfo->smcup = (smc_uart_t *)pram; + } + pinfo->tx_nrfifos = pdata->tx_num_fifo; + pinfo->tx_fifosize = pdata->tx_buf_size; + + pinfo->rx_nrfifos = pdata->rx_num_fifo; + pinfo->rx_fifosize = pdata->rx_buf_size; + + pinfo->port.uartclk = pdata->uart_clk; + pinfo->port.mapbase = (unsigned long)mem; + pinfo->port.irq = platform_get_irq(pdev, 0); + + return 0; +} + #ifdef CONFIG_SERIAL_CPM_CONSOLE /* * Print a string to the serial port trying not to disturb @@ -1027,7 +1110,7 @@ static void cpm_uart_console_write(struct console *co, const char *s, * If the buffer address is in the CPM DPRAM, don't * convert it. */ - cp = cpm2cpu_addr(bdp->cbd_bufaddr); + cp = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); *cp = *s; @@ -1044,7 +1127,7 @@ static void cpm_uart_console_write(struct console *co, const char *s, while ((bdp->cbd_sc & BD_SC_READY) != 0) ; - cp = cpm2cpu_addr(bdp->cbd_bufaddr); + cp = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); *cp = 13; bdp->cbd_datlen = 1; @@ -1067,9 +1150,7 @@ static void cpm_uart_console_write(struct console *co, const char *s, pinfo->tx_cur = (volatile cbd_t *) bdp; } -/* - * Setup console. Be careful is called early ! - */ + static int __init cpm_uart_console_setup(struct console *co, char *options) { struct uart_port *port; @@ -1080,9 +1161,27 @@ static int __init cpm_uart_console_setup(struct console *co, char *options) int flow = 'n'; int ret; + struct fs_uart_platform_info *pdata; + struct platform_device* pdev = early_uart_get_pdev(co->index); + port = (struct uart_port *)&cpm_uart_ports[cpm_uart_port_map[co->index]]; pinfo = (struct uart_cpm_port *)port; + if (!pdev) { + pr_info("cpm_uart: console: compat mode\n"); + /* compatibility - will be cleaned up */ + cpm_uart_init_portdesc(); + + if (pinfo->set_lineif) + pinfo->set_lineif(pinfo); + } else { + pdata = pdev->dev.platform_data; + if (pdata) + if (pdata->init_ioports) + pdata->init_ioports(); + + cpm_uart_drv_get_platform_data(pdev, 1); + } pinfo->flags |= FLAG_CONSOLE; @@ -1097,14 +1196,6 @@ static int __init cpm_uart_console_setup(struct console *co, char *options) baud = 9600; } - /* - * Setup any port IO, connect any baud rate generators, - * etc. This is expected to be handled by board - * dependant code - */ - if (pinfo->set_lineif) - pinfo->set_lineif(pinfo); - if (IS_SMC(pinfo)) { pinfo->smcp->smc_smcm &= ~(SMCM_RX | SMCM_TX); pinfo->smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); @@ -1143,11 +1234,8 @@ static struct console cpm_scc_uart_console = { int __init cpm_uart_console_init(void) { - int ret = cpm_uart_init_portdesc(); - - if (!ret) - register_console(&cpm_scc_uart_console); - return ret; + register_console(&cpm_scc_uart_console); + return 0; } console_initcall(cpm_uart_console_init); @@ -1165,44 +1253,129 @@ static struct uart_driver cpm_reg = { .minor = SERIAL_CPM_MINOR, .cons = CPM_UART_CONSOLE, }; - -static int __init cpm_uart_init(void) +static int cpm_uart_drv_probe(struct device *dev) { - int ret, i; - - printk(KERN_INFO "Serial: CPM driver $Revision: 0.01 $\n"); + struct platform_device *pdev = to_platform_device(dev); + struct fs_uart_platform_info *pdata; + int ret = -ENODEV; -#ifndef CONFIG_SERIAL_CPM_CONSOLE - ret = cpm_uart_init_portdesc(); - if (ret) + if(!pdev) { + printk(KERN_ERR"CPM UART: platform data missing!\n"); return ret; -#endif + } - cpm_reg.nr = cpm_uart_nr; - ret = uart_register_driver(&cpm_reg); + pdata = pdev->dev.platform_data; + pr_debug("cpm_uart_drv_probe: Adding CPM UART %d\n", cpm_uart_id2nr(pdata->fs_no)); - if (ret) + if ((ret = cpm_uart_drv_get_platform_data(pdev, 0))) return ret; - for (i = 0; i < cpm_uart_nr; i++) { - int con = cpm_uart_port_map[i]; - cpm_uart_ports[con].port.line = i; - cpm_uart_ports[con].port.flags = UPF_BOOT_AUTOCONF; - uart_add_one_port(&cpm_reg, &cpm_uart_ports[con].port); - } + if (pdata->init_ioports) + pdata->init_ioports(); - return ret; + ret = uart_add_one_port(&cpm_reg, &cpm_uart_ports[pdata->fs_no].port); + + return ret; } -static void __exit cpm_uart_exit(void) +static int cpm_uart_drv_remove(struct device *dev) { + struct platform_device *pdev = to_platform_device(dev); + struct fs_uart_platform_info *pdata = pdev->dev.platform_data; + + pr_debug("cpm_uart_drv_remove: Removing CPM UART %d\n", + cpm_uart_id2nr(pdata->fs_no)); + + uart_remove_one_port(&cpm_reg, &cpm_uart_ports[pdata->fs_no].port); + return 0; +} + +static struct device_driver cpm_smc_uart_driver = { + .name = "fsl-cpm-smc:uart", + .bus = &platform_bus_type, + .probe = cpm_uart_drv_probe, + .remove = cpm_uart_drv_remove, +}; + +static struct device_driver cpm_scc_uart_driver = { + .name = "fsl-cpm-scc:uart", + .bus = &platform_bus_type, + .probe = cpm_uart_drv_probe, + .remove = cpm_uart_drv_remove, +}; + +/* + This is supposed to match uart devices on platform bus, + */ +static int match_is_uart (struct device* dev, void* data) +{ + struct platform_device* pdev = container_of(dev, struct platform_device, dev); + int ret = 0; + /* this was setfunc as uart */ + if(strstr(pdev->name,":uart")) { + ret = 1; + } + return ret; +} + + +static int cpm_uart_init(void) { + + int ret; int i; + struct device *dev; + printk(KERN_INFO "Serial: CPM driver $Revision: 0.02 $\n"); + + /* lookup the bus for uart devices */ + dev = bus_find_device(&platform_bus_type, NULL, 0, match_is_uart); + + /* There are devices on the bus - all should be OK */ + if (dev) { + cpm_uart_count(); + cpm_reg.nr = cpm_uart_nr; + + if (!(ret = uart_register_driver(&cpm_reg))) { + if ((ret = driver_register(&cpm_smc_uart_driver))) { + uart_unregister_driver(&cpm_reg); + return ret; + } + if ((ret = driver_register(&cpm_scc_uart_driver))) { + driver_unregister(&cpm_scc_uart_driver); + uart_unregister_driver(&cpm_reg); + } + } + } else { + /* No capable platform devices found - falling back to legacy mode */ + pr_info("cpm_uart: WARNING: no UART devices found on platform bus!\n"); + pr_info( + "cpm_uart: the driver will guess configuration, but this mode is no longer supported.\n"); +#ifndef CONFIG_SERIAL_CPM_CONSOLE + ret = cpm_uart_init_portdesc(); + if (ret) + return ret; +#endif + + cpm_reg.nr = cpm_uart_nr; + ret = uart_register_driver(&cpm_reg); + + if (ret) + return ret; + + for (i = 0; i < cpm_uart_nr; i++) { + int con = cpm_uart_port_map[i]; + cpm_uart_ports[con].port.line = i; + cpm_uart_ports[con].port.flags = UPF_BOOT_AUTOCONF; + uart_add_one_port(&cpm_reg, &cpm_uart_ports[con].port); + } - for (i = 0; i < cpm_uart_nr; i++) { - int con = cpm_uart_port_map[i]; - uart_remove_one_port(&cpm_reg, &cpm_uart_ports[con].port); } + return ret; +} +static void __exit cpm_uart_exit(void) +{ + driver_unregister(&cpm_scc_uart_driver); + driver_unregister(&cpm_smc_uart_driver); uart_unregister_driver(&cpm_reg); } diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm1.c b/drivers/serial/cpm_uart/cpm_uart_cpm1.c index d789ee55cbb..17406a05ce1 100644 --- a/drivers/serial/cpm_uart/cpm_uart_cpm1.c +++ b/drivers/serial/cpm_uart/cpm_uart_cpm1.c @@ -8,6 +8,8 @@ * * Copyright (C) 2004 Freescale Semiconductor, Inc. * (C) 2004 Intracom, S.A. + * (C) 2006 MontaVista Software, Inc. + * Vitaly Bordug <vbordug@ru.mvista.com> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -81,58 +83,11 @@ void cpm_line_cr_cmd(int line, int cmd) void smc1_lineif(struct uart_cpm_port *pinfo) { - volatile cpm8xx_t *cp = cpmp; - - (void)cp; /* fix warning */ -#if defined (CONFIG_MPC885ADS) - /* Enable SMC1 transceivers */ - { - cp->cp_pepar |= 0x000000c0; - cp->cp_pedir &= ~0x000000c0; - cp->cp_peso &= ~0x00000040; - cp->cp_peso |= 0x00000080; - } -#elif defined (CONFIG_MPC86XADS) - unsigned int iobits = 0x000000c0; - - if (!pinfo->is_portb) { - cp->cp_pbpar |= iobits; - cp->cp_pbdir &= ~iobits; - cp->cp_pbodr &= ~iobits; - } else { - ((immap_t *)IMAP_ADDR)->im_ioport.iop_papar |= iobits; - ((immap_t *)IMAP_ADDR)->im_ioport.iop_padir &= ~iobits; - ((immap_t *)IMAP_ADDR)->im_ioport.iop_paodr &= ~iobits; - } -#endif pinfo->brg = 1; } void smc2_lineif(struct uart_cpm_port *pinfo) { - volatile cpm8xx_t *cp = cpmp; - - (void)cp; /* fix warning */ -#if defined (CONFIG_MPC885ADS) - cp->cp_pepar |= 0x00000c00; - cp->cp_pedir &= ~0x00000c00; - cp->cp_peso &= ~0x00000400; - cp->cp_peso |= 0x00000800; -#elif defined (CONFIG_MPC86XADS) - unsigned int iobits = 0x00000c00; - - if (!pinfo->is_portb) { - cp->cp_pbpar |= iobits; - cp->cp_pbdir &= ~iobits; - cp->cp_pbodr &= ~iobits; - } else { - ((immap_t *)IMAP_ADDR)->im_ioport.iop_papar |= iobits; - ((immap_t *)IMAP_ADDR)->im_ioport.iop_padir &= ~iobits; - ((immap_t *)IMAP_ADDR)->im_ioport.iop_paodr &= ~iobits; - } - -#endif - pinfo->brg = 2; } @@ -191,7 +146,7 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) /* was hostalloc but changed cause it blows away the */ /* large tlb mapping when pinning the kernel area */ mem_addr = (u8 *) cpm_dpram_addr(cpm_dpalloc(memsz, 8)); - dma_addr = 0; + dma_addr = (u32)mem_addr; } else mem_addr = dma_alloc_coherent(NULL, memsz, &dma_addr, GFP_KERNEL); @@ -204,8 +159,9 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) } pinfo->dp_addr = dp_offset; - pinfo->mem_addr = mem_addr; - pinfo->dma_addr = dma_addr; + pinfo->mem_addr = mem_addr; /* virtual address*/ + pinfo->dma_addr = dma_addr; /* physical address*/ + pinfo->mem_size = memsz; pinfo->rx_buf = mem_addr; pinfo->tx_buf = pinfo->rx_buf + L1_CACHE_ALIGN(pinfo->rx_nrfifos diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c b/drivers/serial/cpm_uart/cpm_uart_cpm2.c index fd9e53ed3fe..4b2de08f46d 100644 --- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c +++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c @@ -8,6 +8,8 @@ * * Copyright (C) 2004 Freescale Semiconductor, Inc. * (C) 2004 Intracom, S.A. + * (C) 2006 MontaVista Software, Inc. + * Vitaly Bordug <vbordug@ru.mvista.com> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -142,14 +144,6 @@ void scc2_lineif(struct uart_cpm_port *pinfo) * be supported in a sane fashion. */ #ifndef CONFIG_STX_GP3 -#ifdef CONFIG_MPC8560_ADS - volatile iop_cpm2_t *io = &cpm2_immr->im_ioport; - io->iop_ppard |= 0x00000018; - io->iop_psord &= ~0x00000008; /* Rx */ - io->iop_psord &= ~0x00000010; /* Tx */ - io->iop_pdird &= ~0x00000008; /* Rx */ - io->iop_pdird |= 0x00000010; /* Tx */ -#else volatile iop_cpm2_t *io = &cpm2_immr->im_ioport; io->iop_pparb |= 0x008b0000; io->iop_pdirb |= 0x00880000; @@ -157,7 +151,6 @@ void scc2_lineif(struct uart_cpm_port *pinfo) io->iop_pdirb &= ~0x00030000; io->iop_psorb &= ~0x00030000; #endif -#endif cpm2_immr->im_cpmux.cmx_scr &= 0xff00ffff; cpm2_immr->im_cpmux.cmx_scr |= 0x00090000; pinfo->brg = 2; @@ -218,8 +211,10 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) memsz = L1_CACHE_ALIGN(pinfo->rx_nrfifos * pinfo->rx_fifosize) + L1_CACHE_ALIGN(pinfo->tx_nrfifos * pinfo->tx_fifosize); - if (is_con) + if (is_con) { mem_addr = alloc_bootmem(memsz); + dma_addr = mem_addr; + } else mem_addr = dma_alloc_coherent(NULL, memsz, &dma_addr, GFP_KERNEL); @@ -234,6 +229,7 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) pinfo->dp_addr = dp_offset; pinfo->mem_addr = mem_addr; pinfo->dma_addr = dma_addr; + pinfo->mem_size = memsz; pinfo->rx_buf = mem_addr; pinfo->tx_buf = pinfo->rx_buf + L1_CACHE_ALIGN(pinfo->rx_nrfifos diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c index c3b7a6673e9..d202eb4f384 100644 --- a/drivers/serial/imx.c +++ b/drivers/serial/imx.c @@ -45,6 +45,7 @@ #include <asm/io.h> #include <asm/irq.h> #include <asm/hardware.h> +#include <asm/arch/imx-uart.h> /* We've been assigned a range on the "Low-density serial ports" major */ #define SERIAL_IMX_MAJOR 204 @@ -73,7 +74,8 @@ struct imx_port { struct uart_port port; struct timer_list timer; unsigned int old_status; - int txirq,rxirq,rtsirq; + int txirq,rxirq,rtsirq; + int have_rtscts:1; }; /* @@ -491,8 +493,12 @@ imx_set_termios(struct uart_port *port, struct termios *termios, ucr2 = UCR2_SRST | UCR2_IRTS; if (termios->c_cflag & CRTSCTS) { - ucr2 &= ~UCR2_IRTS; - ucr2 |= UCR2_CTSC; + if( sport->have_rtscts ) { + ucr2 &= ~UCR2_IRTS; + ucr2 |= UCR2_CTSC; + } else { + termios->c_cflag &= ~CRTSCTS; + } } if (termios->c_cflag & CSTOPB) @@ -719,27 +725,6 @@ static void __init imx_init_ports(void) imx_ports[i].timer.function = imx_timeout; imx_ports[i].timer.data = (unsigned long)&imx_ports[i]; } - - imx_gpio_mode(PC9_PF_UART1_CTS); - imx_gpio_mode(PC10_PF_UART1_RTS); - imx_gpio_mode(PC11_PF_UART1_TXD); - imx_gpio_mode(PC12_PF_UART1_RXD); - imx_gpio_mode(PB28_PF_UART2_CTS); - imx_gpio_mode(PB29_PF_UART2_RTS); - - imx_gpio_mode(PB30_PF_UART2_TXD); - imx_gpio_mode(PB31_PF_UART2_RXD); - -#if 0 /* We don't need these, on the mx1 the _modem_ side of the uart - * is implemented. - */ - imx_gpio_mode(PD7_AF_UART2_DTR); - imx_gpio_mode(PD8_AF_UART2_DCD); - imx_gpio_mode(PD9_AF_UART2_RI); - imx_gpio_mode(PD10_AF_UART2_DSR); -#endif - - } #ifdef CONFIG_SERIAL_IMX_CONSOLE @@ -932,7 +917,14 @@ static int serial_imx_resume(struct platform_device *dev) static int serial_imx_probe(struct platform_device *dev) { + struct imxuart_platform_data *pdata; + imx_ports[dev->id].port.dev = &dev->dev; + + pdata = (struct imxuart_platform_data *)dev->dev.platform_data; + if(pdata && (pdata->flags & IMXUART_HAVE_RTSCTS)) + imx_ports[dev->id].have_rtscts = 1; + uart_add_one_port(&imx_reg, &imx_ports[dev->id].port); platform_set_drvdata(dev, &imx_ports[dev->id]); return 0; diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c index fcd7744c425..aeb8153ccf2 100644 --- a/drivers/serial/serial_core.c +++ b/drivers/serial/serial_core.c @@ -1500,20 +1500,18 @@ uart_block_til_ready(struct file *filp, struct uart_state *state) static struct uart_state *uart_get(struct uart_driver *drv, int line) { struct uart_state *state; + int ret = 0; - mutex_lock(&port_mutex); state = drv->state + line; if (mutex_lock_interruptible(&state->mutex)) { - state = ERR_PTR(-ERESTARTSYS); - goto out; + ret = -ERESTARTSYS; + goto err; } state->count++; - if (!state->port) { - state->count--; - mutex_unlock(&state->mutex); - state = ERR_PTR(-ENXIO); - goto out; + if (!state->port || state->port->flags & UPF_DEAD) { + ret = -ENXIO; + goto err_unlock; } if (!state->info) { @@ -1531,15 +1529,17 @@ static struct uart_state *uart_get(struct uart_driver *drv, int line) tasklet_init(&state->info->tlet, uart_tasklet_action, (unsigned long)state); } else { - state->count--; - mutex_unlock(&state->mutex); - state = ERR_PTR(-ENOMEM); + ret = -ENOMEM; + goto err_unlock; } } - - out: - mutex_unlock(&port_mutex); return state; + + err_unlock: + state->count--; + mutex_unlock(&state->mutex); + err: + return ERR_PTR(ret); } /* @@ -2085,45 +2085,6 @@ uart_configure_port(struct uart_driver *drv, struct uart_state *state, } } -/* - * This reverses the effects of uart_configure_port, hanging up the - * port before removal. - */ -static void -uart_unconfigure_port(struct uart_driver *drv, struct uart_state *state) -{ - struct uart_port *port = state->port; - struct uart_info *info = state->info; - - if (info && info->tty) - tty_vhangup(info->tty); - - mutex_lock(&state->mutex); - - state->info = NULL; - - /* - * Free the port IO and memory resources, if any. - */ - if (port->type != PORT_UNKNOWN) - port->ops->release_port(port); - - /* - * Indicate that there isn't a port here anymore. - */ - port->type = PORT_UNKNOWN; - - /* - * Kill the tasklet, and free resources. - */ - if (info) { - tasklet_kill(&info->tlet); - kfree(info); - } - - mutex_unlock(&state->mutex); -} - static struct tty_operations uart_ops = { .open = uart_open, .close = uart_close, @@ -2270,6 +2231,7 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *port) state = drv->state + port->line; mutex_lock(&port_mutex); + mutex_lock(&state->mutex); if (state->port) { ret = -EINVAL; goto out; @@ -2304,7 +2266,13 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *port) port->cons && !(port->cons->flags & CON_ENABLED)) register_console(port->cons); + /* + * Ensure UPF_DEAD is not set. + */ + port->flags &= ~UPF_DEAD; + out: + mutex_unlock(&state->mutex); mutex_unlock(&port_mutex); return ret; @@ -2322,6 +2290,7 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *port) int uart_remove_one_port(struct uart_driver *drv, struct uart_port *port) { struct uart_state *state = drv->state + port->line; + struct uart_info *info; BUG_ON(in_interrupt()); @@ -2332,11 +2301,48 @@ int uart_remove_one_port(struct uart_driver *drv, struct uart_port *port) mutex_lock(&port_mutex); /* + * Mark the port "dead" - this prevents any opens from + * succeeding while we shut down the port. + */ + mutex_lock(&state->mutex); + port->flags |= UPF_DEAD; + mutex_unlock(&state->mutex); + + /* * Remove the devices from devfs */ tty_unregister_device(drv->tty_driver, port->line); - uart_unconfigure_port(drv, state); + info = state->info; + if (info && info->tty) + tty_vhangup(info->tty); + + /* + * All users of this port should now be disconnected from + * this driver, and the port shut down. We should be the + * only thread fiddling with this port from now on. + */ + state->info = NULL; + + /* + * Free the port IO and memory resources, if any. + */ + if (port->type != PORT_UNKNOWN) + port->ops->release_port(port); + + /* + * Indicate that there isn't a port here anymore. + */ + port->type = PORT_UNKNOWN; + + /* + * Kill the tasklet, and free resources. + */ + if (info) { + tasklet_kill(&info->tlet); + kfree(info); + } + state->port = NULL; mutex_unlock(&port_mutex); diff --git a/drivers/sn/ioc3.c b/drivers/sn/ioc3.c index 0b49ff78efc..501316b198e 100644 --- a/drivers/sn/ioc3.c +++ b/drivers/sn/ioc3.c @@ -678,7 +678,7 @@ static int ioc3_probe(struct pci_dev *pdev, const struct pci_device_id *pci_id) /* Track PCI-device specific data */ pci_set_drvdata(pdev, idd); down_write(&ioc3_devices_rwsem); - list_add(&idd->list, &ioc3_devices); + list_add_tail(&idd->list, &ioc3_devices); idd->id = ioc3_counter++; up_write(&ioc3_devices_rwsem); diff --git a/drivers/sn/ioc4.c b/drivers/sn/ioc4.c index 67140a5804f..cdeff909403 100644 --- a/drivers/sn/ioc4.c +++ b/drivers/sn/ioc4.c @@ -310,7 +310,7 @@ ioc4_probe(struct pci_dev *pdev, const struct pci_device_id *pci_id) pci_set_drvdata(idd->idd_pdev, idd); mutex_lock(&ioc4_mutex); - list_add(&idd->idd_list, &ioc4_devices); + list_add_tail(&idd->idd_list, &ioc4_devices); /* Add this IOC4 to all submodules */ list_for_each_entry(is, &ioc4_submodules, is_list) { diff --git a/drivers/usb/gadget/net2280.c b/drivers/usb/gadget/net2280.c index 6a4b93ad108..0b929349395 100644 --- a/drivers/usb/gadget/net2280.c +++ b/drivers/usb/gadget/net2280.c @@ -2166,7 +2166,7 @@ static void handle_ep_small (struct net2280_ep *ep) ep->stopped = 1; set_halt (ep); mode = 2; - } else if (!req && ep->stopped) + } else if (!req && !ep->stopped) write_fifo (ep, NULL); } } else { @@ -2280,9 +2280,7 @@ static void handle_ep_small (struct net2280_ep *ep) /* if we wrote it all, we're usually done */ if (req->req.actual == req->req.length) { if (ep->num == 0) { - /* wait for control status */ - if (mode != 2) - req = NULL; + /* send zlps until the status stage */ } else if (!req->req.zero || len != ep->ep.maxpacket) mode = 2; } @@ -2744,6 +2742,10 @@ static irqreturn_t net2280_irq (int irq, void *_dev, struct pt_regs * r) { struct net2280 *dev = _dev; + /* shared interrupt, not ours */ + if (!(readl(&dev->regs->irqstat0) & (1 << INTA_ASSERTED))) + return IRQ_NONE; + spin_lock (&dev->lock); /* handle disconnect, dma, and more */ @@ -2831,13 +2833,13 @@ static int net2280_probe (struct pci_dev *pdev, const struct pci_device_id *id) } /* alloc, and start init */ - dev = kmalloc (sizeof *dev, SLAB_KERNEL); + dev = kzalloc (sizeof *dev, SLAB_KERNEL); if (dev == NULL){ retval = -ENOMEM; goto done; } - memset (dev, 0, sizeof *dev); + pci_set_drvdata (pdev, dev); spin_lock_init (&dev->lock); dev->pdev = pdev; dev->gadget.ops = &net2280_ops; @@ -2950,7 +2952,6 @@ static int net2280_probe (struct pci_dev *pdev, const struct pci_device_id *id) dev->chiprev = get_idx_reg (dev->regs, REG_CHIPREV) & 0xffff; /* done */ - pci_set_drvdata (pdev, dev); INFO (dev, "%s\n", driver_desc); INFO (dev, "irq %s, pci mem %p, chip rev %04x\n", bufp, base, dev->chiprev); diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c index 1e03f1a5a5f..a1bd2bea6de 100644 --- a/drivers/usb/host/ehci-pci.c +++ b/drivers/usb/host/ehci-pci.c @@ -350,7 +350,7 @@ static const struct hc_driver ehci_pci_hc_driver = { /* PCI driver selection metadata; PCI hotplugging uses this */ static const struct pci_device_id pci_ids [] = { { /* handle any USB 2.0 EHCI controller */ - PCI_DEVICE_CLASS(((PCI_CLASS_SERIAL_USB << 8) | 0x20), ~0), + PCI_DEVICE_CLASS(PCI_CLASS_SERIAL_USB_EHCI, ~0), .driver_data = (unsigned long) &ehci_pci_hc_driver, }, { /* end: all zeroes */ } diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c index 1bfe96f4d04..b268537e389 100644 --- a/drivers/usb/host/ohci-pci.c +++ b/drivers/usb/host/ohci-pci.c @@ -206,7 +206,7 @@ static const struct hc_driver ohci_pci_hc_driver = { static const struct pci_device_id pci_ids [] = { { /* handle any USB OHCI controller */ - PCI_DEVICE_CLASS((PCI_CLASS_SERIAL_USB << 8) | 0x10, ~0), + PCI_DEVICE_CLASS(PCI_CLASS_SERIAL_USB_OHCI, ~0), .driver_data = (unsigned long) &ohci_pci_hc_driver, }, { /* end: all zeroes */ } }; diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c index c0c4db78b59..d225e11f405 100644 --- a/drivers/usb/host/uhci-hcd.c +++ b/drivers/usb/host/uhci-hcd.c @@ -858,7 +858,7 @@ static const struct hc_driver uhci_driver = { static const struct pci_device_id uhci_pci_ids[] = { { /* handle any USB UHCI controller */ - PCI_DEVICE_CLASS(((PCI_CLASS_SERIAL_USB << 8) | 0x00), ~0), + PCI_DEVICE_CLASS(PCI_CLASS_SERIAL_USB_UHCI, ~0), .driver_data = (unsigned long) &uhci_driver, }, { /* end: all zeroes */ } }; diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index f5851db67f5..82151207d81 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -308,6 +308,7 @@ static struct ftdi_sio_quirk ftdi_HE_TIRA1_quirk = { static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_IRTRANS_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_IPLUS_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SIO_PID) }, { USB_DEVICE(FTDI_VID, FTDI_8U232AM_PID) }, { USB_DEVICE(FTDI_VID, FTDI_8U232AM_ALT_PID) }, @@ -493,6 +494,8 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_WESTREX_MODEL_777_PID) }, { USB_DEVICE(FTDI_VID, FTDI_WESTREX_MODEL_8900F_PID) }, { USB_DEVICE(FTDI_VID, FTDI_PCDJ_DAC2_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_RRCIRKITS_LOCOBUFFER_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_ASK_RDR400_PID) }, { USB_DEVICE(ICOM_ID1_VID, ICOM_ID1_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_TMU_PID) }, { }, /* Optional parameter entry */ diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index 2155f0e4a37..2c55a5ea9c9 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -39,6 +39,9 @@ /* www.thoughttechnology.com/ TT-USB provide with procomp use ftdi_sio */ #define FTDI_TTUSB_PID 0xFF20 /* Product Id */ +/* iPlus device */ +#define FTDI_IPLUS_PID 0xD070 /* Product Id */ + /* www.crystalfontz.com devices - thanx for providing free devices for evaluation ! */ /* they use the ftdi chipset for the USB interface and the vendor id is the same */ #define FTDI_XF_632_PID 0xFC08 /* 632: 16x2 Character Display */ @@ -153,6 +156,11 @@ #define ICOM_ID1_PID 0x0004 /* + * ASK.fr devices + */ +#define FTDI_ASK_RDR400_PID 0xC991 /* ASK RDR 400 series card reader */ + +/* * DSS-20 Sync Station for Sony Ericsson P800 */ @@ -400,6 +408,11 @@ #define FTDI_WESTREX_MODEL_8900F_PID 0xDC01 /* Model 8900F */ /* + * RR-CirKits LocoBuffer USB (http://www.rr-cirkits.com) + */ +#define FTDI_RRCIRKITS_LOCOBUFFER_PID 0xc7d0 /* LocoBuffer USB */ + +/* * Eclo (http://www.eclo.pt/) product IDs. * PID 0xEA90 submitted by Martin Grill. */ diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index ccf746b27d4..c96714bb1cb 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -61,6 +61,7 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(ELCOM_VENDOR_ID, ELCOM_PRODUCT_ID) }, { USB_DEVICE(ELCOM_VENDOR_ID, ELCOM_PRODUCT_ID_UCSGT) }, { USB_DEVICE(ITEGNO_VENDOR_ID, ITEGNO_PRODUCT_ID) }, + { USB_DEVICE(ITEGNO_VENDOR_ID, ITEGNO_PRODUCT_ID_2080) }, { USB_DEVICE(MA620_VENDOR_ID, MA620_PRODUCT_ID) }, { USB_DEVICE(RATOC_VENDOR_ID, RATOC_PRODUCT_ID) }, { USB_DEVICE(TRIPP_VENDOR_ID, TRIPP_PRODUCT_ID) }, diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h index 09f379b19e9..7f29e81d3e3 100644 --- a/drivers/usb/serial/pl2303.h +++ b/drivers/usb/serial/pl2303.h @@ -26,6 +26,7 @@ #define ITEGNO_VENDOR_ID 0x0eba #define ITEGNO_PRODUCT_ID 0x1080 +#define ITEGNO_PRODUCT_ID_2080 0x2080 #define MA620_VENDOR_ID 0x0df7 #define MA620_PRODUCT_ID 0x0620 diff --git a/drivers/usb/serial/whiteheat.c b/drivers/usb/serial/whiteheat.c index 557411c6e7c..f806553cd9a 100644 --- a/drivers/usb/serial/whiteheat.c +++ b/drivers/usb/serial/whiteheat.c @@ -508,6 +508,7 @@ no_firmware: err("%s: Unable to retrieve firmware version, try replugging\n", serial->type->description); err("%s: If the firmware is not running (status led not blinking)\n", serial->type->description); err("%s: please contact support@connecttech.com\n", serial->type->description); + kfree(result); return -ENODEV; no_command_private: diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index c4a9dcff5f2..aec5ea8682d 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -411,7 +411,7 @@ UNUSUAL_DEV( 0x050d, 0x0115, 0x0133, 0x0133, UNUSUAL_DEV( 0x0525, 0xa140, 0x0100, 0x0100, "Iomega", "USB Clik! 40", - US_SC_8070, US_PR_BULK, NULL, + US_SC_8070, US_PR_DEVICE, NULL, US_FL_FIX_INQUIRY ), /* Yakumo Mega Image 37 @@ -773,6 +773,13 @@ UNUSUAL_DEV( 0x069b, 0x3004, 0x0001, 0x0001, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_FIX_CAPACITY ), +/* Reported by Olivier Blondeau <zeitoun@gmail.com> */ +UNUSUAL_DEV( 0x0727, 0x0306, 0x0100, 0x0100, + "ATMEL", + "SND1 Storage", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_IGNORE_RESIDUE), + /* Submitted by Roman Hodek <roman@hodek.net> */ UNUSUAL_DEV( 0x0781, 0x0001, 0x0200, 0x0200, "Sandisk", diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig index 9060e713744..4587087d777 100644 --- a/drivers/video/Kconfig +++ b/drivers/video/Kconfig @@ -400,6 +400,8 @@ config FB_ASILIANT select FB_CFB_FILLRECT select FB_CFB_COPYAREA select FB_CFB_IMAGEBLIT + help + This is the frame buffer device driver for the Asiliant 69030 chipset config FB_IMSTT bool "IMS Twin Turbo display support" diff --git a/drivers/video/au1200fb.c b/drivers/video/au1200fb.c index b367de30b98..600d3e0e08b 100644 --- a/drivers/video/au1200fb.c +++ b/drivers/video/au1200fb.c @@ -1920,1925 +1920,3 @@ module_exit(au1200fb_cleanup); MODULE_DESCRIPTION(DRIVER_DESC); MODULE_LICENSE("GPL"); -/* - * BRIEF MODULE DESCRIPTION - * Au1200 LCD Driver. - * - * Copyright 2004-2005 AMD - * Author: AMD - * - * Based on: - * linux/drivers/video/skeletonfb.c -- Skeleton for a frame buffer device - * Created 28 Dec 1997 by Geert Uytterhoeven - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - */ - -#include <linux/module.h> -#include <linux/platform_device.h> -#include <linux/kernel.h> -#include <linux/errno.h> -#include <linux/string.h> -#include <linux/mm.h> -#include <linux/fb.h> -#include <linux/init.h> -#include <linux/interrupt.h> -#include <linux/ctype.h> -#include <linux/dma-mapping.h> - -#include <asm/mach-au1x00/au1000.h> -#include "au1200fb.h" - -#ifdef CONFIG_PM -#include <asm/mach-au1x00/au1xxx_pm.h> -#endif - -#ifndef CONFIG_FB_AU1200_DEVS -#define CONFIG_FB_AU1200_DEVS 4 -#endif - -#define DRIVER_NAME "au1200fb" -#define DRIVER_DESC "LCD controller driver for AU1200 processors" - -#define DEBUG 1 - -#define print_err(f, arg...) printk(KERN_ERR DRIVER_NAME ": " f "\n", ## arg) -#define print_warn(f, arg...) printk(KERN_WARNING DRIVER_NAME ": " f "\n", ## arg) -#define print_info(f, arg...) printk(KERN_INFO DRIVER_NAME ": " f "\n", ## arg) - -#if DEBUG -#define print_dbg(f, arg...) printk(KERN_DEBUG __FILE__ ": " f "\n", ## arg) -#else -#define print_dbg(f, arg...) do {} while (0) -#endif - - -#define AU1200_LCD_FB_IOCTL 0x46FF - -#define AU1200_LCD_SET_SCREEN 1 -#define AU1200_LCD_GET_SCREEN 2 -#define AU1200_LCD_SET_WINDOW 3 -#define AU1200_LCD_GET_WINDOW 4 -#define AU1200_LCD_SET_PANEL 5 -#define AU1200_LCD_GET_PANEL 6 - -#define SCREEN_SIZE (1<< 1) -#define SCREEN_BACKCOLOR (1<< 2) -#define SCREEN_BRIGHTNESS (1<< 3) -#define SCREEN_COLORKEY (1<< 4) -#define SCREEN_MASK (1<< 5) - -struct au1200_lcd_global_regs_t { - unsigned int flags; - unsigned int xsize; - unsigned int ysize; - unsigned int backcolor; - unsigned int brightness; - unsigned int colorkey; - unsigned int mask; - unsigned int panel_choice; - char panel_desc[80]; - -}; - -#define WIN_POSITION (1<< 0) -#define WIN_ALPHA_COLOR (1<< 1) -#define WIN_ALPHA_MODE (1<< 2) -#define WIN_PRIORITY (1<< 3) -#define WIN_CHANNEL (1<< 4) -#define WIN_BUFFER_FORMAT (1<< 5) -#define WIN_COLOR_ORDER (1<< 6) -#define WIN_PIXEL_ORDER (1<< 7) -#define WIN_SIZE (1<< 8) -#define WIN_COLORKEY_MODE (1<< 9) -#define WIN_DOUBLE_BUFFER_MODE (1<< 10) -#define WIN_RAM_ARRAY_MODE (1<< 11) -#define WIN_BUFFER_SCALE (1<< 12) -#define WIN_ENABLE (1<< 13) - -struct au1200_lcd_window_regs_t { - unsigned int flags; - unsigned int xpos; - unsigned int ypos; - unsigned int alpha_color; - unsigned int alpha_mode; - unsigned int priority; - unsigned int channel; - unsigned int buffer_format; - unsigned int color_order; - unsigned int pixel_order; - unsigned int xsize; - unsigned int ysize; - unsigned int colorkey_mode; - unsigned int double_buffer_mode; - unsigned int ram_array_mode; - unsigned int xscale; - unsigned int yscale; - unsigned int enable; -}; - - -struct au1200_lcd_iodata_t { - unsigned int subcmd; - struct au1200_lcd_global_regs_t global; - struct au1200_lcd_window_regs_t window; -}; - -#if defined(__BIG_ENDIAN) -#define LCD_CONTROL_DEFAULT_PO LCD_CONTROL_PO_11 -#else -#define LCD_CONTROL_DEFAULT_PO LCD_CONTROL_PO_00 -#endif -#define LCD_CONTROL_DEFAULT_SBPPF LCD_CONTROL_SBPPF_565 - -/* Private, per-framebuffer management information (independent of the panel itself) */ -struct au1200fb_device { - struct fb_info fb_info; /* FB driver info record */ - - int plane; - unsigned char* fb_mem; /* FrameBuffer memory map */ - unsigned int fb_len; - dma_addr_t fb_phys; -}; - -static struct au1200fb_device _au1200fb_devices[CONFIG_FB_AU1200_DEVS]; -/********************************************************************/ - -/* LCD controller restrictions */ -#define AU1200_LCD_MAX_XRES 1280 -#define AU1200_LCD_MAX_YRES 1024 -#define AU1200_LCD_MAX_BPP 32 -#define AU1200_LCD_MAX_CLK 96000000 /* fixme: this needs to go away ? */ -#define AU1200_LCD_NBR_PALETTE_ENTRIES 256 - -/* Default number of visible screen buffer to allocate */ -#define AU1200FB_NBR_VIDEO_BUFFERS 1 - -/********************************************************************/ - -static struct au1200_lcd *lcd = (struct au1200_lcd *) AU1200_LCD_ADDR; -static int window_index = 2; /* default is zero */ -static int panel_index = 2; /* default is zero */ -static struct window_settings *win; -static struct panel_settings *panel; -static int noblanking = 1; -static int nohwcursor = 0; - -struct window_settings { - unsigned char name[64]; - uint32 mode_backcolor; - uint32 mode_colorkey; - uint32 mode_colorkeymsk; - struct { - int xres; - int yres; - int xpos; - int ypos; - uint32 mode_winctrl1; /* winctrl1[FRM,CCO,PO,PIPE] */ - uint32 mode_winenable; - } w[4]; -}; - -#if defined(__BIG_ENDIAN) -#define LCD_WINCTRL1_PO_16BPP LCD_WINCTRL1_PO_00 -#else -#define LCD_WINCTRL1_PO_16BPP LCD_WINCTRL1_PO_01 -#endif - -extern int board_au1200fb_panel_init (void); -extern int board_au1200fb_panel_shutdown (void); - -#ifdef CONFIG_PM -int au1200fb_pm_callback(au1xxx_power_dev_t *dev, - au1xxx_request_t request, void *data); -au1xxx_power_dev_t *LCD_pm_dev; -#endif - -/* - * Default window configurations - */ -static struct window_settings windows[] = { - { /* Index 0 */ - "0-FS gfx, 1-video, 2-ovly gfx, 3-ovly gfx", - /* mode_backcolor */ 0x006600ff, - /* mode_colorkey,msk*/ 0, 0, - { - { - /* xres, yres, xpos, ypos */ 0, 0, 0, 0, - /* mode_winctrl1 */ LCD_WINCTRL1_FRM_16BPP565 | - LCD_WINCTRL1_PO_16BPP, - /* mode_winenable*/ LCD_WINENABLE_WEN0, - }, - { - /* xres, yres, xpos, ypos */ 100, 100, 100, 100, - /* mode_winctrl1 */ LCD_WINCTRL1_FRM_16BPP565 | - LCD_WINCTRL1_PO_16BPP | - LCD_WINCTRL1_PIPE, - /* mode_winenable*/ LCD_WINENABLE_WEN1, - }, - { - /* xres, yres, xpos, ypos */ 0, 0, 0, 0, - /* mode_winctrl1 */ LCD_WINCTRL1_FRM_16BPP565 | - LCD_WINCTRL1_PO_16BPP, - /* mode_winenable*/ 0, - }, - { - /* xres, yres, xpos, ypos */ 0, 0, 0, 0, - /* mode_winctrl1 */ LCD_WINCTRL1_FRM_16BPP565 | - LCD_WINCTRL1_PO_16BPP | - LCD_WINCTRL1_PIPE, - /* mode_winenable*/ 0, - }, - }, - }, - - { /* Index 1 */ - "0-FS gfx, 1-video, 2-ovly gfx, 3-ovly gfx", - /* mode_backcolor */ 0x006600ff, - /* mode_colorkey,msk*/ 0, 0, - { - { - /* xres, yres, xpos, ypos */ 320, 240, 5, 5, - /* mode_winctrl1 */ LCD_WINCTRL1_FRM_24BPP | - LCD_WINCTRL1_PO_00, - /* mode_winenable*/ LCD_WINENABLE_WEN0, - }, - { - /* xres, yres, xpos, ypos */ 0, 0, 0, 0, - /* mode_winctrl1 */ LCD_WINCTRL1_FRM_16BPP565 - | LCD_WINCTRL1_PO_16BPP, - /* mode_winenable*/ 0, - }, - { - /* xres, yres, xpos, ypos */ 100, 100, 0, 0, - /* mode_winctrl1 */ LCD_WINCTRL1_FRM_16BPP565 | - LCD_WINCTRL1_PO_16BPP | - LCD_WINCTRL1_PIPE, - /* mode_winenable*/ 0/*LCD_WINENABLE_WEN2*/, - }, - { - /* xres, yres, xpos, ypos */ 200, 25, 0, 0, - /* mode_winctrl1 */ LCD_WINCTRL1_FRM_16BPP565 | - LCD_WINCTRL1_PO_16BPP | - LCD_WINCTRL1_PIPE, - /* mode_winenable*/ 0, - }, - }, - }, - { /* Index 2 */ - "0-FS gfx, 1-video, 2-ovly gfx, 3-ovly gfx", - /* mode_backcolor */ 0x006600ff, - /* mode_colorkey,msk*/ 0, 0, - { - { - /* xres, yres, xpos, ypos */ 0, 0, 0, 0, - /* mode_winctrl1 */ LCD_WINCTRL1_FRM_16BPP565 | - LCD_WINCTRL1_PO_16BPP, - /* mode_winenable*/ LCD_WINENABLE_WEN0, - }, - { - /* xres, yres, xpos, ypos */ 0, 0, 0, 0, - /* mode_winctrl1 */ LCD_WINCTRL1_FRM_16BPP565 | - LCD_WINCTRL1_PO_16BPP, - /* mode_winenable*/ 0, - }, - { - /* xres, yres, xpos, ypos */ 0, 0, 0, 0, - /* mode_winctrl1 */ LCD_WINCTRL1_FRM_32BPP | - LCD_WINCTRL1_PO_00|LCD_WINCTRL1_PIPE, - /* mode_winenable*/ 0/*LCD_WINENABLE_WEN2*/, - }, - { - /* xres, yres, xpos, ypos */ 0, 0, 0, 0, - /* mode_winctrl1 */ LCD_WINCTRL1_FRM_16BPP565 | - LCD_WINCTRL1_PO_16BPP | - LCD_WINCTRL1_PIPE, - /* mode_winenable*/ 0, - }, - }, - }, - /* Need VGA 640 @ 24bpp, @ 32bpp */ - /* Need VGA 800 @ 24bpp, @ 32bpp */ - /* Need VGA 1024 @ 24bpp, @ 32bpp */ -}; - -/* - * Controller configurations for various panels. - */ - -struct panel_settings -{ - const char name[25]; /* Full name <vendor>_<model> */ - - struct fb_monspecs monspecs; /* FB monitor specs */ - - /* panel timings */ - uint32 mode_screen; - uint32 mode_horztiming; - uint32 mode_verttiming; - uint32 mode_clkcontrol; - uint32 mode_pwmdiv; - uint32 mode_pwmhi; - uint32 mode_outmask; - uint32 mode_fifoctrl; - uint32 mode_toyclksrc; - uint32 mode_backlight; - uint32 mode_auxpll; - int (*device_init)(void); - int (*device_shutdown)(void); -#define Xres min_xres -#define Yres min_yres - u32 min_xres; /* Minimum horizontal resolution */ - u32 max_xres; /* Maximum horizontal resolution */ - u32 min_yres; /* Minimum vertical resolution */ - u32 max_yres; /* Maximum vertical resolution */ -}; - -/********************************************************************/ -/* fixme: Maybe a modedb for the CRT ? otherwise panels should be as-is */ - -/* List of panels known to work with the AU1200 LCD controller. - * To add a new panel, enter the same specifications as the - * Generic_TFT one, and MAKE SURE that it doesn't conflicts - * with the controller restrictions. Restrictions are: - * - * STN color panels: max_bpp <= 12 - * STN mono panels: max_bpp <= 4 - * TFT panels: max_bpp <= 16 - * max_xres <= 800 - * max_yres <= 600 - */ -static struct panel_settings known_lcd_panels[] = -{ - [0] = { /* QVGA 320x240 H:33.3kHz V:110Hz */ - .name = "QVGA_320x240", - .monspecs = { - .modedb = NULL, - .modedb_len = 0, - .hfmin = 30000, - .hfmax = 70000, - .vfmin = 60, - .vfmax = 60, - .dclkmin = 6000000, - .dclkmax = 28000000, - .input = FB_DISP_RGB, - }, - .mode_screen = LCD_SCREEN_SX_N(320) | - LCD_SCREEN_SY_N(240), - .mode_horztiming = 0x00c4623b, - .mode_verttiming = 0x00502814, - .mode_clkcontrol = 0x00020002, /* /4=24Mhz */ - .mode_pwmdiv = 0x00000000, - .mode_pwmhi = 0x00000000, - .mode_outmask = 0x00FFFFFF, - .mode_fifoctrl = 0x2f2f2f2f, - .mode_toyclksrc = 0x00000004, /* AUXPLL directly */ - .mode_backlight = 0x00000000, - .mode_auxpll = 8, /* 96MHz AUXPLL */ - .device_init = NULL, - .device_shutdown = NULL, - 320, 320, - 240, 240, - }, - - [1] = { /* VGA 640x480 H:30.3kHz V:58Hz */ - .name = "VGA_640x480", - .monspecs = { - .modedb = NULL, - .modedb_len = 0, - .hfmin = 30000, - .hfmax = 70000, - .vfmin = 60, - .vfmax = 60, - .dclkmin = 6000000, - .dclkmax = 28000000, - .input = FB_DISP_RGB, - }, - .mode_screen = 0x13f9df80, - .mode_horztiming = 0x003c5859, - .mode_verttiming = 0x00741201, - .mode_clkcontrol = 0x00020001, /* /4=24Mhz */ - .mode_pwmdiv = 0x00000000, - .mode_pwmhi = 0x00000000, - .mode_outmask = 0x00FFFFFF, - .mode_fifoctrl = 0x2f2f2f2f, - .mode_toyclksrc = 0x00000004, /* AUXPLL directly */ - .mode_backlight = 0x00000000, - .mode_auxpll = 8, /* 96MHz AUXPLL */ - .device_init = NULL, - .device_shutdown = NULL, - 640, 480, - 640, 480, - }, - - [2] = { /* SVGA 800x600 H:46.1kHz V:69Hz */ - .name = "SVGA_800x600", - .monspecs = { - .modedb = NULL, - .modedb_len = 0, - .hfmin = 30000, - .hfmax = 70000, - .vfmin = 60, - .vfmax = 60, - .dclkmin = 6000000, - .dclkmax = 28000000, - .input = FB_DISP_RGB, - }, - .mode_screen = 0x18fa5780, - .mode_horztiming = 0x00dc7e77, - .mode_verttiming = 0x00584805, - .mode_clkcontrol = 0x00020000, /* /2=48Mhz */ - .mode_pwmdiv = 0x00000000, - .mode_pwmhi = 0x00000000, - .mode_outmask = 0x00FFFFFF, - .mode_fifoctrl = 0x2f2f2f2f, - .mode_toyclksrc = 0x00000004, /* AUXPLL directly */ - .mode_backlight = 0x00000000, - .mode_auxpll = 8, /* 96MHz AUXPLL */ - .device_init = NULL, - .device_shutdown = NULL, - 800, 800, - 600, 600, - }, - - [3] = { /* XVGA 1024x768 H:56.2kHz V:70Hz */ - .name = "XVGA_1024x768", - .monspecs = { - .modedb = NULL, - .modedb_len = 0, - .hfmin = 30000, - .hfmax = 70000, - .vfmin = 60, - .vfmax = 60, - .dclkmin = 6000000, - .dclkmax = 28000000, - .input = FB_DISP_RGB, - }, - .mode_screen = 0x1ffaff80, - .mode_horztiming = 0x007d0e57, - .mode_verttiming = 0x00740a01, - .mode_clkcontrol = 0x000A0000, /* /1 */ - .mode_pwmdiv = 0x00000000, - .mode_pwmhi = 0x00000000, - .mode_outmask = 0x00FFFFFF, - .mode_fifoctrl = 0x2f2f2f2f, - .mode_toyclksrc = 0x00000004, /* AUXPLL directly */ - .mode_backlight = 0x00000000, - .mode_auxpll = 6, /* 72MHz AUXPLL */ - .device_init = NULL, - .device_shutdown = NULL, - 1024, 1024, - 768, 768, - }, - - [4] = { /* XVGA XVGA 1280x1024 H:68.5kHz V:65Hz */ - .name = "XVGA_1280x1024", - .monspecs = { - .modedb = NULL, - .modedb_len = 0, - .hfmin = 30000, - .hfmax = 70000, - .vfmin = 60, - .vfmax = 60, - .dclkmin = 6000000, - .dclkmax = 28000000, - .input = FB_DISP_RGB, - }, - .mode_screen = 0x27fbff80, - .mode_horztiming = 0x00cdb2c7, - .mode_verttiming = 0x00600002, - .mode_clkcontrol = 0x000A0000, /* /1 */ - .mode_pwmdiv = 0x00000000, - .mode_pwmhi = 0x00000000, - .mode_outmask = 0x00FFFFFF, - .mode_fifoctrl = 0x2f2f2f2f, - .mode_toyclksrc = 0x00000004, /* AUXPLL directly */ - .mode_backlight = 0x00000000, - .mode_auxpll = 10, /* 120MHz AUXPLL */ - .device_init = NULL, - .device_shutdown = NULL, - 1280, 1280, - 1024, 1024, - }, - - [5] = { /* Samsung 1024x768 TFT */ - .name = "Samsung_1024x768_TFT", - .monspecs = { - .modedb = NULL, - .modedb_len = 0, - .hfmin = 30000, - .hfmax = 70000, - .vfmin = 60, - .vfmax = 60, - .dclkmin = 6000000, - .dclkmax = 28000000, - .input = FB_DISP_RGB, - }, - .mode_screen = 0x1ffaff80, - .mode_horztiming = 0x018cc677, - .mode_verttiming = 0x00241217, - .mode_clkcontrol = 0x00000000, /* SCB 0x1 /4=24Mhz */ - .mode_pwmdiv = 0x8000063f, /* SCB 0x0 */ - .mode_pwmhi = 0x03400000, /* SCB 0x0 */ - .mode_outmask = 0x00FFFFFF, - .mode_fifoctrl = 0x2f2f2f2f, - .mode_toyclksrc = 0x00000004, /* AUXPLL directly */ - .mode_backlight = 0x00000000, - .mode_auxpll = 8, /* 96MHz AUXPLL */ - .device_init = board_au1200fb_panel_init, - .device_shutdown = board_au1200fb_panel_shutdown, - 1024, 1024, - 768, 768, - }, - - [6] = { /* Toshiba 640x480 TFT */ - .name = "Toshiba_640x480_TFT", - .monspecs = { - .modedb = NULL, - .modedb_len = 0, - .hfmin = 30000, - .hfmax = 70000, - .vfmin = 60, - .vfmax = 60, - .dclkmin = 6000000, - .dclkmax = 28000000, - .input = FB_DISP_RGB, - }, - .mode_screen = LCD_SCREEN_SX_N(640) | - LCD_SCREEN_SY_N(480), - .mode_horztiming = LCD_HORZTIMING_HPW_N(96) | - LCD_HORZTIMING_HND1_N(13) | LCD_HORZTIMING_HND2_N(51), - .mode_verttiming = LCD_VERTTIMING_VPW_N(2) | - LCD_VERTTIMING_VND1_N(11) | LCD_VERTTIMING_VND2_N(32), - .mode_clkcontrol = 0x00000000, /* /4=24Mhz */ - .mode_pwmdiv = 0x8000063f, - .mode_pwmhi = 0x03400000, - .mode_outmask = 0x00fcfcfc, - .mode_fifoctrl = 0x2f2f2f2f, - .mode_toyclksrc = 0x00000004, /* AUXPLL directly */ - .mode_backlight = 0x00000000, - .mode_auxpll = 8, /* 96MHz AUXPLL */ - .device_init = board_au1200fb_panel_init, - .device_shutdown = board_au1200fb_panel_shutdown, - 640, 480, - 640, 480, - }, - - [7] = { /* Sharp 320x240 TFT */ - .name = "Sharp_320x240_TFT", - .monspecs = { - .modedb = NULL, - .modedb_len = 0, - .hfmin = 12500, - .hfmax = 20000, - .vfmin = 38, - .vfmax = 81, - .dclkmin = 4500000, - .dclkmax = 6800000, - .input = FB_DISP_RGB, - }, - .mode_screen = LCD_SCREEN_SX_N(320) | - LCD_SCREEN_SY_N(240), - .mode_horztiming = LCD_HORZTIMING_HPW_N(60) | - LCD_HORZTIMING_HND1_N(13) | LCD_HORZTIMING_HND2_N(2), - .mode_verttiming = LCD_VERTTIMING_VPW_N(2) | - LCD_VERTTIMING_VND1_N(2) | LCD_VERTTIMING_VND2_N(5), - .mode_clkcontrol = LCD_CLKCONTROL_PCD_N(7), /*16=6Mhz*/ - .mode_pwmdiv = 0x8000063f, - .mode_pwmhi = 0x03400000, - .mode_outmask = 0x00fcfcfc, - .mode_fifoctrl = 0x2f2f2f2f, - .mode_toyclksrc = 0x00000004, /* AUXPLL directly */ - .mode_backlight = 0x00000000, - .mode_auxpll = 8, /* 96MHz AUXPLL */ - .device_init = board_au1200fb_panel_init, - .device_shutdown = board_au1200fb_panel_shutdown, - 320, 320, - 240, 240, - }, - - [8] = { /* Toppoly TD070WGCB2 7" 856x480 TFT */ - .name = "Toppoly_TD070WGCB2", - .monspecs = { - .modedb = NULL, - .modedb_len = 0, - .hfmin = 30000, - .hfmax = 70000, - .vfmin = 60, - .vfmax = 60, - .dclkmin = 6000000, - .dclkmax = 28000000, - .input = FB_DISP_RGB, - }, - .mode_screen = LCD_SCREEN_SX_N(856) | - LCD_SCREEN_SY_N(480), - .mode_horztiming = LCD_HORZTIMING_HND2_N(43) | - LCD_HORZTIMING_HND1_N(43) | LCD_HORZTIMING_HPW_N(114), - .mode_verttiming = LCD_VERTTIMING_VND2_N(20) | - LCD_VERTTIMING_VND1_N(21) | LCD_VERTTIMING_VPW_N(4), - .mode_clkcontrol = 0x00020001, /* /4=24Mhz */ - .mode_pwmdiv = 0x8000063f, - .mode_pwmhi = 0x03400000, - .mode_outmask = 0x00fcfcfc, - .mode_fifoctrl = 0x2f2f2f2f, - .mode_toyclksrc = 0x00000004, /* AUXPLL directly */ - .mode_backlight = 0x00000000, - .mode_auxpll = 8, /* 96MHz AUXPLL */ - .device_init = board_au1200fb_panel_init, - .device_shutdown = board_au1200fb_panel_shutdown, - 856, 856, - 480, 480, - }, -}; - -#define NUM_PANELS (ARRAY_SIZE(known_lcd_panels)) - -/********************************************************************/ - -#ifdef CONFIG_PM -static int set_brightness(unsigned int brightness) -{ - unsigned int hi1, divider; - - /* limit brightness pwm duty to >= 30/1600 */ - if (brightness < 30) { - brightness = 30; - } - divider = (lcd->pwmdiv & 0x3FFFF) + 1; - hi1 = (lcd->pwmhi >> 16) + 1; - hi1 = (((brightness & 0xFF) + 1) * divider >> 8); - lcd->pwmhi &= 0xFFFF; - lcd->pwmhi |= (hi1 << 16); - - return brightness; -} -#endif /* CONFIG_PM */ - -static int winbpp (unsigned int winctrl1) -{ - int bits = 0; - - /* how many bits are needed for each pixel format */ - switch (winctrl1 & LCD_WINCTRL1_FRM) { - case LCD_WINCTRL1_FRM_1BPP: - bits = 1; - break; - case LCD_WINCTRL1_FRM_2BPP: - bits = 2; - break; - case LCD_WINCTRL1_FRM_4BPP: - bits = 4; - break; - case LCD_WINCTRL1_FRM_8BPP: - bits = 8; - break; - case LCD_WINCTRL1_FRM_12BPP: - case LCD_WINCTRL1_FRM_16BPP655: - case LCD_WINCTRL1_FRM_16BPP565: - case LCD_WINCTRL1_FRM_16BPP556: - case LCD_WINCTRL1_FRM_16BPPI1555: - case LCD_WINCTRL1_FRM_16BPPI5551: - case LCD_WINCTRL1_FRM_16BPPA1555: - case LCD_WINCTRL1_FRM_16BPPA5551: - bits = 16; - break; - case LCD_WINCTRL1_FRM_24BPP: - case LCD_WINCTRL1_FRM_32BPP: - bits = 32; - break; - } - - return bits; -} - -static int fbinfo2index (struct fb_info *fb_info) -{ - int i; - - for (i = 0; i < CONFIG_FB_AU1200_DEVS; ++i) { - if (fb_info == (struct fb_info *)(&_au1200fb_devices[i].fb_info)) - return i; - } - printk("au1200fb: ERROR: fbinfo2index failed!\n"); - return -1; -} - -static int au1200_setlocation (struct au1200fb_device *fbdev, int plane, - int xpos, int ypos) -{ - uint32 winctrl0, winctrl1, winenable, fb_offset = 0; - int xsz, ysz; - - /* FIX!!! NOT CHECKING FOR COMPLETE OFFSCREEN YET */ - - winctrl0 = lcd->window[plane].winctrl0; - winctrl1 = lcd->window[plane].winctrl1; - winctrl0 &= (LCD_WINCTRL0_A | LCD_WINCTRL0_AEN); - winctrl1 &= ~(LCD_WINCTRL1_SZX | LCD_WINCTRL1_SZY); - - /* Check for off-screen adjustments */ - xsz = win->w[plane].xres; - ysz = win->w[plane].yres; - if ((xpos + win->w[plane].xres) > panel->Xres) { - /* Off-screen to the right */ - xsz = panel->Xres - xpos; /* off by 1 ??? */ - /*printk("off screen right\n");*/ - } - - if ((ypos + win->w[plane].yres) > panel->Yres) { - /* Off-screen to the bottom */ - ysz = panel->Yres - ypos; /* off by 1 ??? */ - /*printk("off screen bottom\n");*/ - } - - if (xpos < 0) { - /* Off-screen to the left */ - xsz = win->w[plane].xres + xpos; - fb_offset += (((0 - xpos) * winbpp(lcd->window[plane].winctrl1))/8); - xpos = 0; - /*printk("off screen left\n");*/ - } - - if (ypos < 0) { - /* Off-screen to the top */ - ysz = win->w[plane].yres + ypos; - /* fixme: fb_offset += ((0-ypos)*fb_pars[plane].line_length); */ - ypos = 0; - /*printk("off screen top\n");*/ - } - - /* record settings */ - win->w[plane].xpos = xpos; - win->w[plane].ypos = ypos; - - xsz -= 1; - ysz -= 1; - winctrl0 |= (xpos << 21); - winctrl0 |= (ypos << 10); - winctrl1 |= (xsz << 11); - winctrl1 |= (ysz << 0); - - /* Disable the window while making changes, then restore WINEN */ - winenable = lcd->winenable & (1 << plane); - au_sync(); - lcd->winenable &= ~(1 << plane); - lcd->window[plane].winctrl0 = winctrl0; - lcd->window[plane].winctrl1 = winctrl1; - lcd->window[plane].winbuf0 = - lcd->window[plane].winbuf1 = fbdev->fb_phys; - lcd->window[plane].winbufctrl = 0; /* select winbuf0 */ - lcd->winenable |= winenable; - au_sync(); - - return 0; -} - -static void au1200_setpanel (struct panel_settings *newpanel) -{ - /* - * Perform global setup/init of LCD controller - */ - uint32 winenable; - - /* Make sure all windows disabled */ - winenable = lcd->winenable; - lcd->winenable = 0; - au_sync(); - /* - * Ensure everything is disabled before reconfiguring - */ - if (lcd->screen & LCD_SCREEN_SEN) { - /* Wait for vertical sync period */ - lcd->intstatus = LCD_INT_SS; - while ((lcd->intstatus & LCD_INT_SS) == 0) { - au_sync(); - } - - lcd->screen &= ~LCD_SCREEN_SEN; /*disable the controller*/ - - do { - lcd->intstatus = lcd->intstatus; /*clear interrupts*/ - au_sync(); - /*wait for controller to shut down*/ - } while ((lcd->intstatus & LCD_INT_SD) == 0); - - /* Call shutdown of current panel (if up) */ - /* this must occur last, because if an external clock is driving - the controller, the clock cannot be turned off before first - shutting down the controller. - */ - if (panel->device_shutdown != NULL) - panel->device_shutdown(); - } - - /* Newpanel == NULL indicates a shutdown operation only */ - if (newpanel == NULL) - return; - - panel = newpanel; - - printk("Panel(%s), %dx%d\n", panel->name, panel->Xres, panel->Yres); - - /* - * Setup clocking if internal LCD clock source (assumes sys_auxpll valid) - */ - if (!(panel->mode_clkcontrol & LCD_CLKCONTROL_EXT)) - { - uint32 sys_clksrc; - au_writel(panel->mode_auxpll, SYS_AUXPLL); - sys_clksrc = au_readl(SYS_CLKSRC) & ~0x0000001f; - sys_clksrc |= panel->mode_toyclksrc; - au_writel(sys_clksrc, SYS_CLKSRC); - } - - /* - * Configure panel timings - */ - lcd->screen = panel->mode_screen; - lcd->horztiming = panel->mode_horztiming; - lcd->verttiming = panel->mode_verttiming; - lcd->clkcontrol = panel->mode_clkcontrol; - lcd->pwmdiv = panel->mode_pwmdiv; - lcd->pwmhi = panel->mode_pwmhi; - lcd->outmask = panel->mode_outmask; - lcd->fifoctrl = panel->mode_fifoctrl; - au_sync(); - - /* fixme: Check window settings to make sure still valid - * for new geometry */ -#if 0 - au1200_setlocation(fbdev, 0, win->w[0].xpos, win->w[0].ypos); - au1200_setlocation(fbdev, 1, win->w[1].xpos, win->w[1].ypos); - au1200_setlocation(fbdev, 2, win->w[2].xpos, win->w[2].ypos); - au1200_setlocation(fbdev, 3, win->w[3].xpos, win->w[3].ypos); -#endif - lcd->winenable = winenable; - - /* - * Re-enable screen now that it is configured - */ - lcd->screen |= LCD_SCREEN_SEN; - au_sync(); - - /* Call init of panel */ - if (panel->device_init != NULL) panel->device_init(); - - /* FIX!!!! not appropriate on panel change!!! Global setup/init */ - lcd->intenable = 0; - lcd->intstatus = ~0; - lcd->backcolor = win->mode_backcolor; - - /* Setup Color Key - FIX!!! */ - lcd->colorkey = win->mode_colorkey; - lcd->colorkeymsk = win->mode_colorkeymsk; - - /* Setup HWCursor - FIX!!! Need to support this eventually */ - lcd->hwc.cursorctrl = 0; - lcd->hwc.cursorpos = 0; - lcd->hwc.cursorcolor0 = 0; - lcd->hwc.cursorcolor1 = 0; - lcd->hwc.cursorcolor2 = 0; - lcd->hwc.cursorcolor3 = 0; - - -#if 0 -#define D(X) printk("%25s: %08X\n", #X, X) - D(lcd->screen); - D(lcd->horztiming); - D(lcd->verttiming); - D(lcd->clkcontrol); - D(lcd->pwmdiv); - D(lcd->pwmhi); - D(lcd->outmask); - D(lcd->fifoctrl); - D(lcd->window[0].winctrl0); - D(lcd->window[0].winctrl1); - D(lcd->window[0].winctrl2); - D(lcd->window[0].winbuf0); - D(lcd->window[0].winbuf1); - D(lcd->window[0].winbufctrl); - D(lcd->window[1].winctrl0); - D(lcd->window[1].winctrl1); - D(lcd->window[1].winctrl2); - D(lcd->window[1].winbuf0); - D(lcd->window[1].winbuf1); - D(lcd->window[1].winbufctrl); - D(lcd->window[2].winctrl0); - D(lcd->window[2].winctrl1); - D(lcd->window[2].winctrl2); - D(lcd->window[2].winbuf0); - D(lcd->window[2].winbuf1); - D(lcd->window[2].winbufctrl); - D(lcd->window[3].winctrl0); - D(lcd->window[3].winctrl1); - D(lcd->window[3].winctrl2); - D(lcd->window[3].winbuf0); - D(lcd->window[3].winbuf1); - D(lcd->window[3].winbufctrl); - D(lcd->winenable); - D(lcd->intenable); - D(lcd->intstatus); - D(lcd->backcolor); - D(lcd->winenable); - D(lcd->colorkey); - D(lcd->colorkeymsk); - D(lcd->hwc.cursorctrl); - D(lcd->hwc.cursorpos); - D(lcd->hwc.cursorcolor0); - D(lcd->hwc.cursorcolor1); - D(lcd->hwc.cursorcolor2); - D(lcd->hwc.cursorcolor3); -#endif -} - -static void au1200_setmode(struct au1200fb_device *fbdev) -{ - int plane = fbdev->plane; - /* Window/plane setup */ - lcd->window[plane].winctrl1 = ( 0 - | LCD_WINCTRL1_PRI_N(plane) - | win->w[plane].mode_winctrl1 /* FRM,CCO,PO,PIPE */ - ) ; - - au1200_setlocation(fbdev, plane, win->w[plane].xpos, win->w[plane].ypos); - - lcd->window[plane].winctrl2 = ( 0 - | LCD_WINCTRL2_CKMODE_00 - | LCD_WINCTRL2_DBM - | LCD_WINCTRL2_BX_N( fbdev->fb_info.fix.line_length) - | LCD_WINCTRL2_SCX_1 - | LCD_WINCTRL2_SCY_1 - ) ; - lcd->winenable |= win->w[plane].mode_winenable; - au_sync(); -} - - -/* Inline helpers */ - -/*#define panel_is_dual(panel) ((panel->mode_screen & LCD_SCREEN_PT) == LCD_SCREEN_PT_010)*/ -/*#define panel_is_active(panel)((panel->mode_screen & LCD_SCREEN_PT) == LCD_SCREEN_PT_010)*/ - -#define panel_is_color(panel) ((panel->mode_screen & LCD_SCREEN_PT) <= LCD_SCREEN_PT_CDSTN) - -/* Bitfields format supported by the controller. */ -static struct fb_bitfield rgb_bitfields[][4] = { - /* Red, Green, Blue, Transp */ - [LCD_WINCTRL1_FRM_16BPP655 >> 25] = - { { 10, 6, 0 }, { 5, 5, 0 }, { 0, 5, 0 }, { 0, 0, 0 } }, - - [LCD_WINCTRL1_FRM_16BPP565 >> 25] = - { { 11, 5, 0 }, { 5, 6, 0 }, { 0, 5, 0 }, { 0, 0, 0 } }, - - [LCD_WINCTRL1_FRM_16BPP556 >> 25] = - { { 11, 5, 0 }, { 6, 5, 0 }, { 0, 6, 0 }, { 0, 0, 0 } }, - - [LCD_WINCTRL1_FRM_16BPPI1555 >> 25] = - { { 10, 5, 0 }, { 5, 5, 0 }, { 0, 5, 0 }, { 0, 0, 0 } }, - - [LCD_WINCTRL1_FRM_16BPPI5551 >> 25] = - { { 11, 5, 0 }, { 6, 5, 0 }, { 1, 5, 0 }, { 0, 0, 0 } }, - - [LCD_WINCTRL1_FRM_16BPPA1555 >> 25] = - { { 10, 5, 0 }, { 5, 5, 0 }, { 0, 5, 0 }, { 15, 1, 0 } }, - - [LCD_WINCTRL1_FRM_16BPPA5551 >> 25] = - { { 11, 5, 0 }, { 6, 5, 0 }, { 1, 5, 0 }, { 0, 1, 0 } }, - - [LCD_WINCTRL1_FRM_24BPP >> 25] = - { { 16, 8, 0 }, { 8, 8, 0 }, { 0, 8, 0 }, { 0, 0, 0 } }, - - [LCD_WINCTRL1_FRM_32BPP >> 25] = - { { 16, 8, 0 }, { 8, 8, 0 }, { 0, 8, 0 }, { 24, 0, 0 } }, -}; - -/*-------------------------------------------------------------------------*/ - -/* Helpers */ - -static void au1200fb_update_fbinfo(struct fb_info *fbi) -{ - /* FIX!!!! This also needs to take the window pixel format into account!!! */ - - /* Update var-dependent FB info */ - if (panel_is_color(panel)) { - if (fbi->var.bits_per_pixel <= 8) { - /* palettized */ - fbi->fix.visual = FB_VISUAL_PSEUDOCOLOR; - fbi->fix.line_length = fbi->var.xres_virtual / - (8/fbi->var.bits_per_pixel); - } else { - /* non-palettized */ - fbi->fix.visual = FB_VISUAL_TRUECOLOR; - fbi->fix.line_length = fbi->var.xres_virtual * (fbi->var.bits_per_pixel / 8); - } - } else { - /* mono FIX!!! mono 8 and 4 bits */ - fbi->fix.visual = FB_VISUAL_MONO10; - fbi->fix.line_length = fbi->var.xres_virtual / 8; - } - - fbi->screen_size = fbi->fix.line_length * fbi->var.yres_virtual; - print_dbg("line length: %d\n", fbi->fix.line_length); - print_dbg("bits_per_pixel: %d\n", fbi->var.bits_per_pixel); -} - -/*-------------------------------------------------------------------------*/ - -/* AU1200 framebuffer driver */ - -/* fb_check_var - * Validate var settings with hardware restrictions and modify it if necessary - */ -static int au1200fb_fb_check_var(struct fb_var_screeninfo *var, - struct fb_info *fbi) -{ - struct au1200fb_device *fbdev = (struct au1200fb_device *)fbi; - u32 pixclock; - int screen_size, plane; - - plane = fbdev->plane; - - /* Make sure that the mode respect all LCD controller and - * panel restrictions. */ - var->xres = win->w[plane].xres; - var->yres = win->w[plane].yres; - - /* No need for virtual resolution support */ - var->xres_virtual = var->xres; - var->yres_virtual = var->yres; - - var->bits_per_pixel = winbpp(win->w[plane].mode_winctrl1); - - screen_size = var->xres_virtual * var->yres_virtual; - if (var->bits_per_pixel > 8) screen_size *= (var->bits_per_pixel / 8); - else screen_size /= (8/var->bits_per_pixel); - - if (fbdev->fb_len < screen_size) - return -EINVAL; /* Virtual screen is to big, abort */ - - /* FIX!!!! what are the implicaitons of ignoring this for windows ??? */ - /* The max LCD clock is fixed to 48MHz (value of AUX_CLK). The pixel - * clock can only be obtain by dividing this value by an even integer. - * Fallback to a slower pixel clock if necessary. */ - pixclock = max((u32)(PICOS2KHZ(var->pixclock) * 1000), fbi->monspecs.dclkmin); - pixclock = min(pixclock, min(fbi->monspecs.dclkmax, (u32)AU1200_LCD_MAX_CLK/2)); - - if (AU1200_LCD_MAX_CLK % pixclock) { - int diff = AU1200_LCD_MAX_CLK % pixclock; - pixclock -= diff; - } - - var->pixclock = KHZ2PICOS(pixclock/1000); -#if 0 - if (!panel_is_active(panel)) { - int pcd = AU1200_LCD_MAX_CLK / (pixclock * 2) - 1; - - if (!panel_is_color(panel) - && (panel->control_base & LCD_CONTROL_MPI) && (pcd < 3)) { - /* STN 8bit mono panel support is up to 6MHz pixclock */ - var->pixclock = KHZ2PICOS(6000); - } else if (!pcd) { - /* Other STN panel support is up to 12MHz */ - var->pixclock = KHZ2PICOS(12000); - } - } -#endif - /* Set bitfield accordingly */ - switch (var->bits_per_pixel) { - case 16: - { - /* 16bpp True color. - * These must be set to MATCH WINCTRL[FORM] */ - int idx; - idx = (win->w[0].mode_winctrl1 & LCD_WINCTRL1_FRM) >> 25; - var->red = rgb_bitfields[idx][0]; - var->green = rgb_bitfields[idx][1]; - var->blue = rgb_bitfields[idx][2]; - var->transp = rgb_bitfields[idx][3]; - break; - } - - case 32: - { - /* 32bpp True color. - * These must be set to MATCH WINCTRL[FORM] */ - int idx; - idx = (win->w[0].mode_winctrl1 & LCD_WINCTRL1_FRM) >> 25; - var->red = rgb_bitfields[idx][0]; - var->green = rgb_bitfields[idx][1]; - var->blue = rgb_bitfields[idx][2]; - var->transp = rgb_bitfields[idx][3]; - break; - } - default: - print_dbg("Unsupported depth %dbpp", var->bits_per_pixel); - return -EINVAL; - } - - return 0; -} - -/* fb_set_par - * Set hardware with var settings. This will enable the controller with a - * specific mode, normally validated with the fb_check_var method - */ -static int au1200fb_fb_set_par(struct fb_info *fbi) -{ - struct au1200fb_device *fbdev = (struct au1200fb_device *)fbi; - - au1200fb_update_fbinfo(fbi); - au1200_setmode(fbdev); - - return 0; -} - -/* fb_setcolreg - * Set color in LCD palette. - */ -static int au1200fb_fb_setcolreg(unsigned regno, unsigned red, unsigned green, - unsigned blue, unsigned transp, struct fb_info *fbi) -{ - volatile u32 *palette = lcd->palette; - u32 value; - - if (regno > (AU1200_LCD_NBR_PALETTE_ENTRIES - 1)) - return -EINVAL; - - if (fbi->var.grayscale) { - /* Convert color to grayscale */ - red = green = blue = - (19595 * red + 38470 * green + 7471 * blue) >> 16; - } - - if (fbi->fix.visual == FB_VISUAL_TRUECOLOR) { - /* Place color in the pseudopalette */ - if (regno > 16) - return -EINVAL; - - palette = (u32*) fbi->pseudo_palette; - - red >>= (16 - fbi->var.red.length); - green >>= (16 - fbi->var.green.length); - blue >>= (16 - fbi->var.blue.length); - - value = (red << fbi->var.red.offset) | - (green << fbi->var.green.offset)| - (blue << fbi->var.blue.offset); - value &= 0xFFFF; - - } else if (1 /*FIX!!! panel_is_active(fbdev->panel)*/) { - /* COLOR TFT PALLETTIZED (use RGB 565) */ - value = (red & 0xF800)|((green >> 5) & - 0x07E0)|((blue >> 11) & 0x001F); - value &= 0xFFFF; - - } else if (0 /*panel_is_color(fbdev->panel)*/) { - /* COLOR STN MODE */ - value = 0x1234; - value &= 0xFFF; - } else { - /* MONOCHROME MODE */ - value = (green >> 12) & 0x000F; - value &= 0xF; - } - - palette[regno] = value; - - return 0; -} - -/* fb_blank - * Blank the screen. Depending on the mode, the screen will be - * activated with the backlight color, or desactivated - */ -static int au1200fb_fb_blank(int blank_mode, struct fb_info *fbi) -{ - /* Short-circuit screen blanking */ - if (noblanking) - return 0; - - switch (blank_mode) { - - case FB_BLANK_UNBLANK: - case FB_BLANK_NORMAL: - /* printk("turn on panel\n"); */ - au1200_setpanel(panel); - break; - case FB_BLANK_VSYNC_SUSPEND: - case FB_BLANK_HSYNC_SUSPEND: - case FB_BLANK_POWERDOWN: - /* printk("turn off panel\n"); */ - au1200_setpanel(NULL); - break; - default: - break; - - } - - /* FB_BLANK_NORMAL is a soft blank */ - return (blank_mode == FB_BLANK_NORMAL) ? -EINVAL : 0; -} - -/* fb_mmap - * Map video memory in user space. We don't use the generic fb_mmap - * method mainly to allow the use of the TLB streaming flag (CCA=6) - */ -static int au1200fb_fb_mmap(struct fb_info *info, struct vm_area_struct *vma) - -{ - unsigned int len; - unsigned long start=0, off; - struct au1200fb_device *fbdev = (struct au1200fb_device *) info; - -#ifdef CONFIG_PM - au1xxx_pm_access(LCD_pm_dev); -#endif - - if (vma->vm_pgoff > (~0UL >> PAGE_SHIFT)) { - return -EINVAL; - } - - start = fbdev->fb_phys & PAGE_MASK; - len = PAGE_ALIGN((start & ~PAGE_MASK) + fbdev->fb_len); - - off = vma->vm_pgoff << PAGE_SHIFT; - - if ((vma->vm_end - vma->vm_start + off) > len) { - return -EINVAL; - } - - off += start; - vma->vm_pgoff = off >> PAGE_SHIFT; - - vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot); - pgprot_val(vma->vm_page_prot) |= _CACHE_MASK; /* CCA=7 */ - - vma->vm_flags |= VM_IO; - - return io_remap_pfn_range(vma, vma->vm_start, off >> PAGE_SHIFT, - vma->vm_end - vma->vm_start, - vma->vm_page_prot); - - return 0; -} - -static void set_global(u_int cmd, struct au1200_lcd_global_regs_t *pdata) -{ - - unsigned int hi1, divider; - - /* SCREEN_SIZE: user cannot reset size, must switch panel choice */ - - if (pdata->flags & SCREEN_BACKCOLOR) - lcd->backcolor = pdata->backcolor; - - if (pdata->flags & SCREEN_BRIGHTNESS) { - - // limit brightness pwm duty to >= 30/1600 - if (pdata->brightness < 30) { - pdata->brightness = 30; - } - divider = (lcd->pwmdiv & 0x3FFFF) + 1; - hi1 = (lcd->pwmhi >> 16) + 1; - hi1 = (((pdata->brightness & 0xFF)+1) * divider >> 8); - lcd->pwmhi &= 0xFFFF; - lcd->pwmhi |= (hi1 << 16); - } - - if (pdata->flags & SCREEN_COLORKEY) - lcd->colorkey = pdata->colorkey; - - if (pdata->flags & SCREEN_MASK) - lcd->colorkeymsk = pdata->mask; - au_sync(); -} - -static void get_global(u_int cmd, struct au1200_lcd_global_regs_t *pdata) -{ - unsigned int hi1, divider; - - pdata->xsize = ((lcd->screen & LCD_SCREEN_SX) >> 19) + 1; - pdata->ysize = ((lcd->screen & LCD_SCREEN_SY) >> 8) + 1; - - pdata->backcolor = lcd->backcolor; - pdata->colorkey = lcd->colorkey; - pdata->mask = lcd->colorkeymsk; - - // brightness - hi1 = (lcd->pwmhi >> 16) + 1; - divider = (lcd->pwmdiv & 0x3FFFF) + 1; - pdata->brightness = ((hi1 << 8) / divider) - 1; - au_sync(); -} - -static void set_window(unsigned int plane, - struct au1200_lcd_window_regs_t *pdata) -{ - unsigned int val, bpp; - - /* Window control register 0 */ - if (pdata->flags & WIN_POSITION) { - val = lcd->window[plane].winctrl0 & ~(LCD_WINCTRL0_OX | - LCD_WINCTRL0_OY); - val |= ((pdata->xpos << 21) & LCD_WINCTRL0_OX); - val |= ((pdata->ypos << 10) & LCD_WINCTRL0_OY); - lcd->window[plane].winctrl0 = val; - } - if (pdata->flags & WIN_ALPHA_COLOR) { - val = lcd->window[plane].winctrl0 & ~(LCD_WINCTRL0_A); - val |= ((pdata->alpha_color << 2) & LCD_WINCTRL0_A); - lcd->window[plane].winctrl0 = val; - } - if (pdata->flags & WIN_ALPHA_MODE) { - val = lcd->window[plane].winctrl0 & ~(LCD_WINCTRL0_AEN); - val |= ((pdata->alpha_mode << 1) & LCD_WINCTRL0_AEN); - lcd->window[plane].winctrl0 = val; - } - - /* Window control register 1 */ - if (pdata->flags & WIN_PRIORITY) { - val = lcd->window[plane].winctrl1 & ~(LCD_WINCTRL1_PRI); - val |= ((pdata->priority << 30) & LCD_WINCTRL1_PRI); - lcd->window[plane].winctrl1 = val; - } - if (pdata->flags & WIN_CHANNEL) { - val = lcd->window[plane].winctrl1 & ~(LCD_WINCTRL1_PIPE); - val |= ((pdata->channel << 29) & LCD_WINCTRL1_PIPE); - lcd->window[plane].winctrl1 = val; - } - if (pdata->flags & WIN_BUFFER_FORMAT) { - val = lcd->window[plane].winctrl1 & ~(LCD_WINCTRL1_FRM); - val |= ((pdata->buffer_format << 25) & LCD_WINCTRL1_FRM); - lcd->window[plane].winctrl1 = val; - } - if (pdata->flags & WIN_COLOR_ORDER) { - val = lcd->window[plane].winctrl1 & ~(LCD_WINCTRL1_CCO); - val |= ((pdata->color_order << 24) & LCD_WINCTRL1_CCO); - lcd->window[plane].winctrl1 = val; - } - if (pdata->flags & WIN_PIXEL_ORDER) { - val = lcd->window[plane].winctrl1 & ~(LCD_WINCTRL1_PO); - val |= ((pdata->pixel_order << 22) & LCD_WINCTRL1_PO); - lcd->window[plane].winctrl1 = val; - } - if (pdata->flags & WIN_SIZE) { - val = lcd->window[plane].winctrl1 & ~(LCD_WINCTRL1_SZX | - LCD_WINCTRL1_SZY); - val |= (((pdata->xsize << 11) - 1) & LCD_WINCTRL1_SZX); - val |= (((pdata->ysize) - 1) & LCD_WINCTRL1_SZY); - lcd->window[plane].winctrl1 = val; - /* program buffer line width */ - bpp = winbpp(val) / 8; - val = lcd->window[plane].winctrl2 & ~(LCD_WINCTRL2_BX); - val |= (((pdata->xsize * bpp) << 8) & LCD_WINCTRL2_BX); - lcd->window[plane].winctrl2 = val; - } - - /* Window control register 2 */ - if (pdata->flags & WIN_COLORKEY_MODE) { - val = lcd->window[plane].winctrl2 & ~(LCD_WINCTRL2_CKMODE); - val |= ((pdata->colorkey_mode << 24) & LCD_WINCTRL2_CKMODE); - lcd->window[plane].winctrl2 = val; - } - if (pdata->flags & WIN_DOUBLE_BUFFER_MODE) { - val = lcd->window[plane].winctrl2 & ~(LCD_WINCTRL2_DBM); - val |= ((pdata->double_buffer_mode << 23) & LCD_WINCTRL2_DBM); - lcd->window[plane].winctrl2 = val; - } - if (pdata->flags & WIN_RAM_ARRAY_MODE) { - val = lcd->window[plane].winctrl2 & ~(LCD_WINCTRL2_RAM); - val |= ((pdata->ram_array_mode << 21) & LCD_WINCTRL2_RAM); - lcd->window[plane].winctrl2 = val; - } - - /* Buffer line width programmed with WIN_SIZE */ - - if (pdata->flags & WIN_BUFFER_SCALE) { - val = lcd->window[plane].winctrl2 & ~(LCD_WINCTRL2_SCX | - LCD_WINCTRL2_SCY); - val |= ((pdata->xsize << 11) & LCD_WINCTRL2_SCX); - val |= ((pdata->ysize) & LCD_WINCTRL2_SCY); - lcd->window[plane].winctrl2 = val; - } - - if (pdata->flags & WIN_ENABLE) { - val = lcd->winenable; - val &= ~(1<<plane); - val |= (pdata->enable & 1) << plane; - lcd->winenable = val; - } - au_sync(); -} - -static void get_window(unsigned int plane, - struct au1200_lcd_window_regs_t *pdata) -{ - /* Window control register 0 */ - pdata->xpos = (lcd->window[plane].winctrl0 & LCD_WINCTRL0_OX) >> 21; - pdata->ypos = (lcd->window[plane].winctrl0 & LCD_WINCTRL0_OY) >> 10; - pdata->alpha_color = (lcd->window[plane].winctrl0 & LCD_WINCTRL0_A) >> 2; - pdata->alpha_mode = (lcd->window[plane].winctrl0 & LCD_WINCTRL0_AEN) >> 1; - - /* Window control register 1 */ - pdata->priority = (lcd->window[plane].winctrl1& LCD_WINCTRL1_PRI) >> 30; - pdata->channel = (lcd->window[plane].winctrl1 & LCD_WINCTRL1_PIPE) >> 29; - pdata->buffer_format = (lcd->window[plane].winctrl1 & LCD_WINCTRL1_FRM) >> 25; - pdata->color_order = (lcd->window[plane].winctrl1 & LCD_WINCTRL1_CCO) >> 24; - pdata->pixel_order = (lcd->window[plane].winctrl1 & LCD_WINCTRL1_PO) >> 22; - pdata->xsize = ((lcd->window[plane].winctrl1 & LCD_WINCTRL1_SZX) >> 11) + 1; - pdata->ysize = (lcd->window[plane].winctrl1 & LCD_WINCTRL1_SZY) + 1; - - /* Window control register 2 */ - pdata->colorkey_mode = (lcd->window[plane].winctrl2 & LCD_WINCTRL2_CKMODE) >> 24; - pdata->double_buffer_mode = (lcd->window[plane].winctrl2 & LCD_WINCTRL2_DBM) >> 23; - pdata->ram_array_mode = (lcd->window[plane].winctrl2 & LCD_WINCTRL2_RAM) >> 21; - - pdata->enable = (lcd->winenable >> plane) & 1; - au_sync(); -} - -static int au1200fb_ioctl(struct fb_info *info, unsigned int cmd, - unsigned long arg) -{ - int plane; - int val; - -#ifdef CONFIG_PM - au1xxx_pm_access(LCD_pm_dev); -#endif - - plane = fbinfo2index(info); - print_dbg("au1200fb: ioctl %d on plane %d\n", cmd, plane); - - if (cmd == AU1200_LCD_FB_IOCTL) { - struct au1200_lcd_iodata_t iodata; - - if (copy_from_user(&iodata, (void __user *) arg, sizeof(iodata))) - return -EFAULT; - - print_dbg("FB IOCTL called\n"); - - switch (iodata.subcmd) { - case AU1200_LCD_SET_SCREEN: - print_dbg("AU1200_LCD_SET_SCREEN\n"); - set_global(cmd, &iodata.global); - break; - - case AU1200_LCD_GET_SCREEN: - print_dbg("AU1200_LCD_GET_SCREEN\n"); - get_global(cmd, &iodata.global); - break; - - case AU1200_LCD_SET_WINDOW: - print_dbg("AU1200_LCD_SET_WINDOW\n"); - set_window(plane, &iodata.window); - break; - - case AU1200_LCD_GET_WINDOW: - print_dbg("AU1200_LCD_GET_WINDOW\n"); - get_window(plane, &iodata.window); - break; - - case AU1200_LCD_SET_PANEL: - print_dbg("AU1200_LCD_SET_PANEL\n"); - if ((iodata.global.panel_choice >= 0) && - (iodata.global.panel_choice < - NUM_PANELS)) - { - struct panel_settings *newpanel; - panel_index = iodata.global.panel_choice; - newpanel = &known_lcd_panels[panel_index]; - au1200_setpanel(newpanel); - } - break; - - case AU1200_LCD_GET_PANEL: - print_dbg("AU1200_LCD_GET_PANEL\n"); - iodata.global.panel_choice = panel_index; - break; - - default: - return -EINVAL; - } - - val = copy_to_user((void __user *) arg, &iodata, sizeof(iodata)); - if (val) { - print_dbg("error: could not copy %d bytes\n", val); - return -EFAULT; - } - } - - return 0; -} - - -static struct fb_ops au1200fb_fb_ops = { - .owner = THIS_MODULE, - .fb_check_var = au1200fb_fb_check_var, - .fb_set_par = au1200fb_fb_set_par, - .fb_setcolreg = au1200fb_fb_setcolreg, - .fb_blank = au1200fb_fb_blank, - .fb_fillrect = cfb_fillrect, - .fb_copyarea = cfb_copyarea, - .fb_imageblit = cfb_imageblit, - .fb_sync = NULL, - .fb_ioctl = au1200fb_ioctl, - .fb_mmap = au1200fb_fb_mmap, -}; - -/*-------------------------------------------------------------------------*/ - -static irqreturn_t au1200fb_handle_irq(int irq, void* dev_id, struct pt_regs *regs) -{ - /* Nothing to do for now, just clear any pending interrupt */ - lcd->intstatus = lcd->intstatus; - au_sync(); - - return IRQ_HANDLED; -} - -/*-------------------------------------------------------------------------*/ - -/* AU1200 LCD device probe helpers */ - -static int au1200fb_init_fbinfo(struct au1200fb_device *fbdev) -{ - struct fb_info *fbi = &fbdev->fb_info; - int bpp; - - memset(fbi, 0, sizeof(struct fb_info)); - fbi->fbops = &au1200fb_fb_ops; - - bpp = winbpp(win->w[fbdev->plane].mode_winctrl1); - - /* Copy monitor specs from panel data */ - /* fixme: we're setting up LCD controller windows, so these dont give a - damn as to what the monitor specs are (the panel itself does, but that - isnt done here...so maybe need a generic catchall monitor setting??? */ - memcpy(&fbi->monspecs, &panel->monspecs, sizeof(struct fb_monspecs)); - - /* We first try the user mode passed in argument. If that failed, - * or if no one has been specified, we default to the first mode of the - * panel list. Note that after this call, var data will be set */ - if (!fb_find_mode(&fbi->var, - fbi, - NULL, /* drv_info.opt_mode, */ - fbi->monspecs.modedb, - fbi->monspecs.modedb_len, - fbi->monspecs.modedb, - bpp)) { - - print_err("Cannot find valid mode for panel %s", panel->name); - return -EFAULT; - } - - fbi->pseudo_palette = kmalloc(sizeof(u32) * 16, GFP_KERNEL); - if (!fbi->pseudo_palette) { - return -ENOMEM; - } - memset(fbi->pseudo_palette, 0, sizeof(u32) * 16); - - if (fb_alloc_cmap(&fbi->cmap, AU1200_LCD_NBR_PALETTE_ENTRIES, 0) < 0) { - print_err("Fail to allocate colormap (%d entries)", - AU1200_LCD_NBR_PALETTE_ENTRIES); - kfree(fbi->pseudo_palette); - return -EFAULT; - } - - strncpy(fbi->fix.id, "AU1200", sizeof(fbi->fix.id)); - fbi->fix.smem_start = fbdev->fb_phys; - fbi->fix.smem_len = fbdev->fb_len; - fbi->fix.type = FB_TYPE_PACKED_PIXELS; - fbi->fix.xpanstep = 0; - fbi->fix.ypanstep = 0; - fbi->fix.mmio_start = 0; - fbi->fix.mmio_len = 0; - fbi->fix.accel = FB_ACCEL_NONE; - - fbi->screen_base = (char __iomem *) fbdev->fb_mem; - - au1200fb_update_fbinfo(fbi); - - return 0; -} - -/*-------------------------------------------------------------------------*/ - -/* AU1200 LCD controller device driver */ - -static int au1200fb_drv_probe(struct device *dev) -{ - struct au1200fb_device *fbdev; - unsigned long page; - int bpp, plane, ret; - - if (!dev) - return -EINVAL; - - for (plane = 0; plane < CONFIG_FB_AU1200_DEVS; ++plane) { - bpp = winbpp(win->w[plane].mode_winctrl1); - if (win->w[plane].xres == 0) - win->w[plane].xres = panel->Xres; - if (win->w[plane].yres == 0) - win->w[plane].yres = panel->Yres; - - fbdev = &_au1200fb_devices[plane]; - memset(fbdev, 0, sizeof(struct au1200fb_device)); - fbdev->plane = plane; - - /* Allocate the framebuffer to the maximum screen size */ - fbdev->fb_len = (win->w[plane].xres * win->w[plane].yres * bpp) / 8; - - fbdev->fb_mem = dma_alloc_noncoherent(dev, - PAGE_ALIGN(fbdev->fb_len), - &fbdev->fb_phys, GFP_KERNEL); - if (!fbdev->fb_mem) { - print_err("fail to allocate frambuffer (size: %dK))", - fbdev->fb_len / 1024); - return -ENOMEM; - } - - /* - * Set page reserved so that mmap will work. This is necessary - * since we'll be remapping normal memory. - */ - for (page = (unsigned long)fbdev->fb_phys; - page < PAGE_ALIGN((unsigned long)fbdev->fb_phys + - fbdev->fb_len); - page += PAGE_SIZE) { - SetPageReserved(pfn_to_page(page >> PAGE_SHIFT)); /* LCD DMA is NOT coherent on Au1200 */ - } - print_dbg("Framebuffer memory map at %p", fbdev->fb_mem); - print_dbg("phys=0x%08x, size=%dK", fbdev->fb_phys, fbdev->fb_len / 1024); - - /* Init FB data */ - if ((ret = au1200fb_init_fbinfo(fbdev)) < 0) - goto failed; - - /* Register new framebuffer */ - if ((ret = register_framebuffer(&fbdev->fb_info)) < 0) { - print_err("cannot register new framebuffer"); - goto failed; - } - - au1200fb_fb_set_par(&fbdev->fb_info); - -#if !defined(CONFIG_FRAMEBUFFER_CONSOLE) && defined(CONFIG_LOGO) - if (plane == 0) - if (fb_prepare_logo(&fbdev->fb_info, FB_ROTATE_UR)) { - /* Start display and show logo on boot */ - fb_set_cmap(&fbdev->fb_info.cmap, - &fbdev->fb_info); - - fb_show_logo(&fbdev->fb_info, FB_ROTATE_UR); - } -#endif - } - - /* Now hook interrupt too */ - if ((ret = request_irq(AU1200_LCD_INT, au1200fb_handle_irq, - SA_INTERRUPT | SA_SHIRQ, "lcd", (void *)dev)) < 0) { - print_err("fail to request interrupt line %d (err: %d)", - AU1200_LCD_INT, ret); - goto failed; - } - - return 0; - -failed: - /* NOTE: This only does the current plane/window that failed; others are still active */ - if (fbdev->fb_mem) - dma_free_noncoherent(dev, PAGE_ALIGN(fbdev->fb_len), - fbdev->fb_mem, fbdev->fb_phys); - if (fbdev->fb_info.cmap.len != 0) - fb_dealloc_cmap(&fbdev->fb_info.cmap); - if (fbdev->fb_info.pseudo_palette) - kfree(fbdev->fb_info.pseudo_palette); - if (plane == 0) - free_irq(AU1200_LCD_INT, (void*)dev); - return ret; -} - -static int au1200fb_drv_remove(struct device *dev) -{ - struct au1200fb_device *fbdev; - int plane; - - if (!dev) - return -ENODEV; - - /* Turn off the panel */ - au1200_setpanel(NULL); - - for (plane = 0; plane < CONFIG_FB_AU1200_DEVS; ++plane) - { - fbdev = &_au1200fb_devices[plane]; - - /* Clean up all probe data */ - unregister_framebuffer(&fbdev->fb_info); - if (fbdev->fb_mem) - dma_free_noncoherent(dev, PAGE_ALIGN(fbdev->fb_len), - fbdev->fb_mem, fbdev->fb_phys); - if (fbdev->fb_info.cmap.len != 0) - fb_dealloc_cmap(&fbdev->fb_info.cmap); - if (fbdev->fb_info.pseudo_palette) - kfree(fbdev->fb_info.pseudo_palette); - } - - free_irq(AU1200_LCD_INT, (void *)dev); - - return 0; -} - -#ifdef CONFIG_PM -static int au1200fb_drv_suspend(struct device *dev, u32 state, u32 level) -{ - /* TODO */ - return 0; -} - -static int au1200fb_drv_resume(struct device *dev, u32 level) -{ - /* TODO */ - return 0; -} -#endif /* CONFIG_PM */ - -static struct device_driver au1200fb_driver = { - .name = "au1200-lcd", - .bus = &platform_bus_type, - .probe = au1200fb_drv_probe, - .remove = au1200fb_drv_remove, -#ifdef CONFIG_PM - .suspend = au1200fb_drv_suspend, - .resume = au1200fb_drv_resume, -#endif -}; - -/*-------------------------------------------------------------------------*/ - -/* Kernel driver */ - -static void au1200fb_setup(void) -{ - char* options = NULL; - char* this_opt; - int num_panels = ARRAY_SIZE(known_lcd_panels); - int panel_idx = -1; - - fb_get_options(DRIVER_NAME, &options); - - if (options) { - while ((this_opt = strsep(&options,",")) != NULL) { - /* Panel option - can be panel name, - * "bs" for board-switch, or number/index */ - if (!strncmp(this_opt, "panel:", 6)) { - int i; - long int li; - char *endptr; - this_opt += 6; - /* First check for index, which allows - * to short circuit this mess */ - li = simple_strtol(this_opt, &endptr, 0); - if (*endptr == '\0') { - panel_idx = (int)li; - } - else if (strcmp(this_opt, "bs") == 0) { - extern int board_au1200fb_panel(void); - panel_idx = board_au1200fb_panel(); - } - - else - for (i = 0; i < num_panels; i++) { - if (!strcmp(this_opt, known_lcd_panels[i].name)) { - panel_idx = i; - break; - } - } - - if ((panel_idx < 0) || (panel_idx >= num_panels)) { - print_warn("Panel %s not supported!", this_opt); - } - else - panel_index = panel_idx; - } - - else if (strncmp(this_opt, "nohwcursor", 10) == 0) { - nohwcursor = 1; - } - - /* Unsupported option */ - else { - print_warn("Unsupported option \"%s\"", this_opt); - } - } - } -} - -#ifdef CONFIG_PM -static int au1200fb_pm_callback(au1xxx_power_dev_t *dev, - au1xxx_request_t request, void *data) { - int retval = -1; - unsigned int d = 0; - unsigned int brightness = 0; - - if (request == AU1XXX_PM_SLEEP) { - board_au1200fb_panel_shutdown(); - } - else if (request == AU1XXX_PM_WAKEUP) { - if(dev->prev_state == SLEEP_STATE) - { - int plane; - au1200_setpanel(panel); - for (plane = 0; plane < CONFIG_FB_AU1200_DEVS; ++plane) { - struct au1200fb_device *fbdev; - fbdev = &_au1200fb_devices[plane]; - au1200fb_fb_set_par(&fbdev->fb_info); - } - } - - d = *((unsigned int*)data); - if(d <=10) brightness = 26; - else if(d<=20) brightness = 51; - else if(d<=30) brightness = 77; - else if(d<=40) brightness = 102; - else if(d<=50) brightness = 128; - else if(d<=60) brightness = 153; - else if(d<=70) brightness = 179; - else if(d<=80) brightness = 204; - else if(d<=90) brightness = 230; - else brightness = 255; - set_brightness(brightness); - } else if (request == AU1XXX_PM_GETSTATUS) { - return dev->cur_state; - } else if (request == AU1XXX_PM_ACCESS) { - if (dev->cur_state != SLEEP_STATE) - return retval; - else { - au1200_setpanel(panel); - } - } else if (request == AU1XXX_PM_IDLE) { - } else if (request == AU1XXX_PM_CLEANUP) { - } - - return retval; -} -#endif - -static int __init au1200fb_init(void) -{ - print_info("" DRIVER_DESC ""); - - /* Setup driver with options */ - au1200fb_setup(); - - /* Point to the panel selected */ - panel = &known_lcd_panels[panel_index]; - win = &windows[window_index]; - - printk(DRIVER_NAME ": Panel %d %s\n", panel_index, panel->name); - printk(DRIVER_NAME ": Win %d %s\n", window_index, win->name); - - /* Kickstart the panel, the framebuffers/windows come soon enough */ - au1200_setpanel(panel); - - #ifdef CONFIG_PM - LCD_pm_dev = new_au1xxx_power_device("LCD", &au1200fb_pm_callback, NULL); - if ( LCD_pm_dev == NULL) - printk(KERN_INFO "Unable to create a power management device entry for the au1200fb.\n"); - else - printk(KERN_INFO "Power management device entry for the au1200fb loaded.\n"); - #endif - - return driver_register(&au1200fb_driver); -} - -static void __exit au1200fb_cleanup(void) -{ - driver_unregister(&au1200fb_driver); -} - -module_init(au1200fb_init); -module_exit(au1200fb_cleanup); - -MODULE_DESCRIPTION(DRIVER_DESC); -MODULE_LICENSE("GPL"); diff --git a/drivers/video/fbsysfs.c b/drivers/video/fbsysfs.c index b72b05250a9..34e07399756 100644 --- a/drivers/video/fbsysfs.c +++ b/drivers/video/fbsysfs.c @@ -305,94 +305,6 @@ static ssize_t show_stride(struct class_device *class_device, char *buf) return snprintf(buf, PAGE_SIZE, "%d\n", fb_info->fix.line_length); } -/* Format for cmap is "%02x%c%4x%4x%4x\n" */ -/* %02x entry %c transp %4x red %4x blue %4x green \n */ -/* 256 rows at 16 chars equals 4096, the normal page size */ -/* the code will automatically adjust for different page sizes */ -static ssize_t store_cmap(struct class_device *class_device, const char *buf, - size_t count) -{ - struct fb_info *fb_info = class_get_devdata(class_device); - int rc, i, start, length, transp = 0; - - if ((count > PAGE_SIZE) || ((count % 16) != 0)) - return -EINVAL; - - if (!fb_info->fbops->fb_setcolreg && !fb_info->fbops->fb_setcmap) - return -EINVAL; - - sscanf(buf, "%02x", &start); - length = count / 16; - - for (i = 0; i < length; i++) - if (buf[i * 16 + 2] != ' ') - transp = 1; - - /* If we can batch, do it */ - if (fb_info->fbops->fb_setcmap && length > 1) { - struct fb_cmap umap; - - memset(&umap, 0, sizeof(umap)); - if ((rc = fb_alloc_cmap(&umap, length, transp))) - return rc; - - umap.start = start; - for (i = 0; i < length; i++) { - sscanf(&buf[i * 16 + 3], "%4hx", &umap.red[i]); - sscanf(&buf[i * 16 + 7], "%4hx", &umap.blue[i]); - sscanf(&buf[i * 16 + 11], "%4hx", &umap.green[i]); - if (transp) - umap.transp[i] = (buf[i * 16 + 2] != ' '); - } - rc = fb_info->fbops->fb_setcmap(&umap, fb_info); - fb_copy_cmap(&umap, &fb_info->cmap); - fb_dealloc_cmap(&umap); - - return rc ?: count; - } - for (i = 0; i < length; i++) { - u16 red, blue, green, tsp; - - sscanf(&buf[i * 16 + 3], "%4hx", &red); - sscanf(&buf[i * 16 + 7], "%4hx", &blue); - sscanf(&buf[i * 16 + 11], "%4hx", &green); - tsp = (buf[i * 16 + 2] != ' '); - if ((rc = fb_info->fbops->fb_setcolreg(start++, - red, green, blue, tsp, fb_info))) - return rc; - - fb_info->cmap.red[i] = red; - fb_info->cmap.blue[i] = blue; - fb_info->cmap.green[i] = green; - if (transp) - fb_info->cmap.transp[i] = tsp; - } - return count; -} - -static ssize_t show_cmap(struct class_device *class_device, char *buf) -{ - struct fb_info *fb_info = class_get_devdata(class_device); - unsigned int i; - - if (!fb_info->cmap.red || !fb_info->cmap.blue || - !fb_info->cmap.green) - return -EINVAL; - - if (fb_info->cmap.len > PAGE_SIZE / 16) - return -EINVAL; - - /* don't mess with the format, the buffer is PAGE_SIZE */ - /* 256 entries at 16 chars per line equals 4096 = PAGE_SIZE */ - for (i = 0; i < fb_info->cmap.len; i++) { - snprintf(&buf[ i * 16], PAGE_SIZE - i * 16, "%02x%c%4x%4x%4x\n", i + fb_info->cmap.start, - ((fb_info->cmap.transp && fb_info->cmap.transp[i]) ? '*' : ' '), - fb_info->cmap.red[i], fb_info->cmap.blue[i], - fb_info->cmap.green[i]); - } - return 16 * fb_info->cmap.len; -} - static ssize_t store_blank(struct class_device *class_device, const char * buf, size_t count) { @@ -502,10 +414,12 @@ static ssize_t show_fbstate(struct class_device *class_device, char *buf) return snprintf(buf, PAGE_SIZE, "%d\n", fb_info->state); } +/* When cmap is added back in it should be a binary attribute + * not a text one. Consideration should also be given to converting + * fbdev to use configfs instead of sysfs */ static struct class_device_attribute class_device_attrs[] = { __ATTR(bits_per_pixel, S_IRUGO|S_IWUSR, show_bpp, store_bpp), __ATTR(blank, S_IRUGO|S_IWUSR, show_blank, store_blank), - __ATTR(color_map, S_IRUGO|S_IWUSR, show_cmap, store_cmap), __ATTR(console, S_IRUGO|S_IWUSR, show_console, store_console), __ATTR(cursor, S_IRUGO|S_IWUSR, show_cursor, store_cursor), __ATTR(mode, S_IRUGO|S_IWUSR, show_mode, store_mode), diff --git a/drivers/video/logo/Makefile b/drivers/video/logo/Makefile index 4ef5cd19609..b985dfad6c6 100644 --- a/drivers/video/logo/Makefile +++ b/drivers/video/logo/Makefile @@ -34,7 +34,7 @@ extra-y += $(call logo-cfiles,_clut224,ppm) extra-y += $(call logo-cfiles,_gray256,pgm) # Create commands like "pnmtologo -t mono -n logo_mac_mono -o ..." -quiet_cmd_logo = LOGO $@ +quiet_cmd_logo = LOGO $@ cmd_logo = scripts/pnmtologo \ -t $(patsubst $*_%,%,$(notdir $(basename $<))) \ -n $(notdir $(basename $<)) -o $@ $< diff --git a/fs/block_dev.c b/fs/block_dev.c index af88c43043d..f5958f413bd 100644 --- a/fs/block_dev.c +++ b/fs/block_dev.c @@ -1104,6 +1104,8 @@ const struct file_operations def_blk_fops = { .readv = generic_file_readv, .writev = generic_file_write_nolock, .sendfile = generic_file_sendfile, + .splice_read = generic_file_splice_read, + .splice_write = generic_file_splice_write, }; int ioctl_by_bdev(struct block_device *bdev, unsigned cmd, unsigned long arg) diff --git a/fs/compat.c b/fs/compat.c index 2e32bd34047..970888aad84 100644 --- a/fs/compat.c +++ b/fs/compat.c @@ -1317,6 +1317,26 @@ out: return ret; } +asmlinkage long +compat_sys_vmsplice(int fd, const struct compat_iovec __user *iov32, + unsigned int nr_segs, unsigned int flags) +{ + unsigned i; + struct iovec *iov; + if (nr_segs > UIO_MAXIOV) + return -EINVAL; + iov = compat_alloc_user_space(nr_segs * sizeof(struct iovec)); + for (i = 0; i < nr_segs; i++) { + struct compat_iovec v; + if (get_user(v.iov_base, &iov32[i].iov_base) || + get_user(v.iov_len, &iov32[i].iov_len) || + put_user(compat_ptr(v.iov_base), &iov[i].iov_base) || + put_user(v.iov_len, &iov[i].iov_len)) + return -EFAULT; + } + return sys_vmsplice(fd, iov, nr_segs, flags); +} + /* * Exactly like fs/open.c:sys_open(), except that it doesn't set the * O_LARGEFILE flag. diff --git a/fs/ext3/inode.c b/fs/ext3/inode.c index 48ae0339af1..2edd7eec88f 100644 --- a/fs/ext3/inode.c +++ b/fs/ext3/inode.c @@ -711,7 +711,7 @@ static int ext3_splice_branch(handle_t *handle, struct inode *inode, * direct blocks blocks */ if (num == 0 && blks > 1) { - current_block = le32_to_cpu(where->key + 1); + current_block = le32_to_cpu(where->key) + 1; for (i = 1; i < blks; i++) *(where->p + i ) = cpu_to_le32(current_block++); } @@ -724,7 +724,7 @@ static int ext3_splice_branch(handle_t *handle, struct inode *inode, if (block_i) { block_i->last_alloc_logical_block = block + blks - 1; block_i->last_alloc_physical_block = - le32_to_cpu(where[num].key + blks - 1); + le32_to_cpu(where[num].key) + blks - 1; } /* We are done with atomic stuff, now do the rest of housekeeping */ @@ -814,11 +814,13 @@ int ext3_get_blocks_handle(handle_t *handle, struct inode *inode, /* Simplest case - block found, no allocation needed */ if (!partial) { - first_block = chain[depth - 1].key; + first_block = le32_to_cpu(chain[depth - 1].key); clear_buffer_new(bh_result); count++; /*map more blocks*/ while (count < maxblocks && count <= blocks_to_boundary) { + unsigned long blk; + if (!verify_chain(chain, partial)) { /* * Indirect block might be removed by @@ -831,8 +833,9 @@ int ext3_get_blocks_handle(handle_t *handle, struct inode *inode, count = 0; break; } - if (le32_to_cpu(*(chain[depth-1].p+count) == - (first_block + count))) + blk = le32_to_cpu(*(chain[depth-1].p + count)); + + if (blk == first_block + count) count++; else break; diff --git a/fs/locks.c b/fs/locks.c index efad798824d..6f99c0a6f83 100644 --- a/fs/locks.c +++ b/fs/locks.c @@ -446,15 +446,14 @@ static struct lock_manager_operations lease_manager_ops = { */ static int lease_init(struct file *filp, int type, struct file_lock *fl) { + if (assign_type(fl, type) != 0) + return -EINVAL; + fl->fl_owner = current->files; fl->fl_pid = current->tgid; fl->fl_file = filp; fl->fl_flags = FL_LEASE; - if (assign_type(fl, type) != 0) { - locks_free_lock(fl); - return -EINVAL; - } fl->fl_start = 0; fl->fl_end = OFFSET_MAX; fl->fl_ops = NULL; @@ -466,16 +465,19 @@ static int lease_init(struct file *filp, int type, struct file_lock *fl) static int lease_alloc(struct file *filp, int type, struct file_lock **flp) { struct file_lock *fl = locks_alloc_lock(); - int error; + int error = -ENOMEM; if (fl == NULL) - return -ENOMEM; + goto out; error = lease_init(filp, type, fl); - if (error) - return error; + if (error) { + locks_free_lock(fl); + fl = NULL; + } +out: *flp = fl; - return 0; + return error; } /* Check if two locks overlap each other. @@ -1372,6 +1374,7 @@ static int __setlease(struct file *filp, long arg, struct file_lock **flp) goto out; if (my_before != NULL) { + *flp = *my_before; error = lease->fl_lmops->fl_change(my_before, arg); goto out; } diff --git a/fs/pipe.c b/fs/pipe.c index 7fefb10db8d..5acd8954aaa 100644 --- a/fs/pipe.c +++ b/fs/pipe.c @@ -55,7 +55,8 @@ void pipe_wait(struct pipe_inode_info *pipe) } static int -pipe_iov_copy_from_user(void *to, struct iovec *iov, unsigned long len) +pipe_iov_copy_from_user(void *to, struct iovec *iov, unsigned long len, + int atomic) { unsigned long copy; @@ -64,8 +65,13 @@ pipe_iov_copy_from_user(void *to, struct iovec *iov, unsigned long len) iov++; copy = min_t(unsigned long, len, iov->iov_len); - if (copy_from_user(to, iov->iov_base, copy)) - return -EFAULT; + if (atomic) { + if (__copy_from_user_inatomic(to, iov->iov_base, copy)) + return -EFAULT; + } else { + if (copy_from_user(to, iov->iov_base, copy)) + return -EFAULT; + } to += copy; len -= copy; iov->iov_base += copy; @@ -75,7 +81,8 @@ pipe_iov_copy_from_user(void *to, struct iovec *iov, unsigned long len) } static int -pipe_iov_copy_to_user(struct iovec *iov, const void *from, unsigned long len) +pipe_iov_copy_to_user(struct iovec *iov, const void *from, unsigned long len, + int atomic) { unsigned long copy; @@ -84,8 +91,13 @@ pipe_iov_copy_to_user(struct iovec *iov, const void *from, unsigned long len) iov++; copy = min_t(unsigned long, len, iov->iov_len); - if (copy_to_user(iov->iov_base, from, copy)) - return -EFAULT; + if (atomic) { + if (__copy_to_user_inatomic(iov->iov_base, from, copy)) + return -EFAULT; + } else { + if (copy_to_user(iov->iov_base, from, copy)) + return -EFAULT; + } from += copy; len -= copy; iov->iov_base += copy; @@ -94,13 +106,52 @@ pipe_iov_copy_to_user(struct iovec *iov, const void *from, unsigned long len) return 0; } +/* + * Attempt to pre-fault in the user memory, so we can use atomic copies. + * Returns the number of bytes not faulted in. + */ +static int iov_fault_in_pages_write(struct iovec *iov, unsigned long len) +{ + while (!iov->iov_len) + iov++; + + while (len > 0) { + unsigned long this_len; + + this_len = min_t(unsigned long, len, iov->iov_len); + if (fault_in_pages_writeable(iov->iov_base, this_len)) + break; + + len -= this_len; + iov++; + } + + return len; +} + +/* + * Pre-fault in the user memory, so we can use atomic copies. + */ +static void iov_fault_in_pages_read(struct iovec *iov, unsigned long len) +{ + while (!iov->iov_len) + iov++; + + while (len > 0) { + unsigned long this_len; + + this_len = min_t(unsigned long, len, iov->iov_len); + fault_in_pages_readable(iov->iov_base, this_len); + len -= this_len; + iov++; + } +} + static void anon_pipe_buf_release(struct pipe_inode_info *pipe, struct pipe_buffer *buf) { struct page *page = buf->page; - buf->flags &= ~PIPE_BUF_FLAG_STOLEN; - /* * If nobody else uses this page, and we don't already have a * temporary page, let's keep track of it as a one-deep @@ -112,38 +163,58 @@ static void anon_pipe_buf_release(struct pipe_inode_info *pipe, page_cache_release(page); } -static void * anon_pipe_buf_map(struct file *file, struct pipe_inode_info *pipe, - struct pipe_buffer *buf) +void *generic_pipe_buf_map(struct pipe_inode_info *pipe, + struct pipe_buffer *buf, int atomic) { + if (atomic) { + buf->flags |= PIPE_BUF_FLAG_ATOMIC; + return kmap_atomic(buf->page, KM_USER0); + } + return kmap(buf->page); } -static void anon_pipe_buf_unmap(struct pipe_inode_info *pipe, - struct pipe_buffer *buf) +void generic_pipe_buf_unmap(struct pipe_inode_info *pipe, + struct pipe_buffer *buf, void *map_data) { - kunmap(buf->page); + if (buf->flags & PIPE_BUF_FLAG_ATOMIC) { + buf->flags &= ~PIPE_BUF_FLAG_ATOMIC; + kunmap_atomic(map_data, KM_USER0); + } else + kunmap(buf->page); } -static int anon_pipe_buf_steal(struct pipe_inode_info *pipe, - struct pipe_buffer *buf) +int generic_pipe_buf_steal(struct pipe_inode_info *pipe, + struct pipe_buffer *buf) { - buf->flags |= PIPE_BUF_FLAG_STOLEN; - return 0; + struct page *page = buf->page; + + if (page_count(page) == 1) { + lock_page(page); + return 0; + } + + return 1; } -static void anon_pipe_buf_get(struct pipe_inode_info *info, - struct pipe_buffer *buf) +void generic_pipe_buf_get(struct pipe_inode_info *info, struct pipe_buffer *buf) { page_cache_get(buf->page); } +int generic_pipe_buf_pin(struct pipe_inode_info *info, struct pipe_buffer *buf) +{ + return 0; +} + static struct pipe_buf_operations anon_pipe_buf_ops = { .can_merge = 1, - .map = anon_pipe_buf_map, - .unmap = anon_pipe_buf_unmap, + .map = generic_pipe_buf_map, + .unmap = generic_pipe_buf_unmap, + .pin = generic_pipe_buf_pin, .release = anon_pipe_buf_release, - .steal = anon_pipe_buf_steal, - .get = anon_pipe_buf_get, + .steal = generic_pipe_buf_steal, + .get = generic_pipe_buf_get, }; static ssize_t @@ -174,22 +245,33 @@ pipe_readv(struct file *filp, const struct iovec *_iov, struct pipe_buf_operations *ops = buf->ops; void *addr; size_t chars = buf->len; - int error; + int error, atomic; if (chars > total_len) chars = total_len; - addr = ops->map(filp, pipe, buf); - if (IS_ERR(addr)) { + error = ops->pin(pipe, buf); + if (error) { if (!ret) - ret = PTR_ERR(addr); + error = ret; break; } - error = pipe_iov_copy_to_user(iov, addr + buf->offset, chars); - ops->unmap(pipe, buf); + + atomic = !iov_fault_in_pages_write(iov, chars); +redo: + addr = ops->map(pipe, buf, atomic); + error = pipe_iov_copy_to_user(iov, addr + buf->offset, chars, atomic); + ops->unmap(pipe, buf, addr); if (unlikely(error)) { + /* + * Just retry with the slow path if we failed. + */ + if (atomic) { + atomic = 0; + goto redo; + } if (!ret) - ret = -EFAULT; + ret = error; break; } ret += chars; @@ -293,21 +375,28 @@ pipe_writev(struct file *filp, const struct iovec *_iov, int offset = buf->offset + buf->len; if (ops->can_merge && offset + chars <= PAGE_SIZE) { + int error, atomic = 1; void *addr; - int error; - addr = ops->map(filp, pipe, buf); - if (IS_ERR(addr)) { - error = PTR_ERR(addr); + error = ops->pin(pipe, buf); + if (error) goto out; - } + + iov_fault_in_pages_read(iov, chars); +redo1: + addr = ops->map(pipe, buf, atomic); error = pipe_iov_copy_from_user(offset + addr, iov, - chars); - ops->unmap(pipe, buf); + chars, atomic); + ops->unmap(pipe, buf, addr); ret = error; do_wakeup = 1; - if (error) + if (error) { + if (atomic) { + atomic = 0; + goto redo1; + } goto out; + } buf->len += chars; total_len -= chars; ret = chars; @@ -330,7 +419,8 @@ pipe_writev(struct file *filp, const struct iovec *_iov, int newbuf = (pipe->curbuf + bufs) & (PIPE_BUFFERS-1); struct pipe_buffer *buf = pipe->bufs + newbuf; struct page *page = pipe->tmp_page; - int error; + char *src; + int error, atomic = 1; if (!page) { page = alloc_page(GFP_HIGHUSER); @@ -350,11 +440,27 @@ pipe_writev(struct file *filp, const struct iovec *_iov, if (chars > total_len) chars = total_len; - error = pipe_iov_copy_from_user(kmap(page), iov, chars); - kunmap(page); + iov_fault_in_pages_read(iov, chars); +redo2: + if (atomic) + src = kmap_atomic(page, KM_USER0); + else + src = kmap(page); + + error = pipe_iov_copy_from_user(src, iov, chars, + atomic); + if (atomic) + kunmap_atomic(src, KM_USER0); + else + kunmap(page); + if (unlikely(error)) { + if (atomic) { + atomic = 0; + goto redo2; + } if (!ret) - ret = -EFAULT; + ret = error; break; } ret += chars; diff --git a/fs/splice.c b/fs/splice.c index 447ebc0a37f..a285fd746dc 100644 --- a/fs/splice.c +++ b/fs/splice.c @@ -51,7 +51,7 @@ struct splice_pipe_desc { * addition of remove_mapping(). If success is returned, the caller may * attempt to reuse this page for another destination. */ -static int page_cache_pipe_buf_steal(struct pipe_inode_info *info, +static int page_cache_pipe_buf_steal(struct pipe_inode_info *pipe, struct pipe_buffer *buf) { struct page *page = buf->page; @@ -78,21 +78,19 @@ static int page_cache_pipe_buf_steal(struct pipe_inode_info *info, return 1; } - buf->flags |= PIPE_BUF_FLAG_STOLEN | PIPE_BUF_FLAG_LRU; + buf->flags |= PIPE_BUF_FLAG_LRU; return 0; } -static void page_cache_pipe_buf_release(struct pipe_inode_info *info, +static void page_cache_pipe_buf_release(struct pipe_inode_info *pipe, struct pipe_buffer *buf) { page_cache_release(buf->page); - buf->page = NULL; - buf->flags &= ~(PIPE_BUF_FLAG_STOLEN | PIPE_BUF_FLAG_LRU); + buf->flags &= ~PIPE_BUF_FLAG_LRU; } -static void *page_cache_pipe_buf_map(struct file *file, - struct pipe_inode_info *info, - struct pipe_buffer *buf) +static int page_cache_pipe_buf_pin(struct pipe_inode_info *pipe, + struct pipe_buffer *buf) { struct page *page = buf->page; int err; @@ -118,64 +116,45 @@ static void *page_cache_pipe_buf_map(struct file *file, } /* - * Page is ok afterall, fall through to mapping. + * Page is ok afterall, we are done. */ unlock_page(page); } - return kmap(page); + return 0; error: unlock_page(page); - return ERR_PTR(err); -} - -static void page_cache_pipe_buf_unmap(struct pipe_inode_info *info, - struct pipe_buffer *buf) -{ - kunmap(buf->page); -} - -static void *user_page_pipe_buf_map(struct file *file, - struct pipe_inode_info *pipe, - struct pipe_buffer *buf) -{ - return kmap(buf->page); -} - -static void user_page_pipe_buf_unmap(struct pipe_inode_info *pipe, - struct pipe_buffer *buf) -{ - kunmap(buf->page); -} - -static void page_cache_pipe_buf_get(struct pipe_inode_info *info, - struct pipe_buffer *buf) -{ - page_cache_get(buf->page); + return err; } static struct pipe_buf_operations page_cache_pipe_buf_ops = { .can_merge = 0, - .map = page_cache_pipe_buf_map, - .unmap = page_cache_pipe_buf_unmap, + .map = generic_pipe_buf_map, + .unmap = generic_pipe_buf_unmap, + .pin = page_cache_pipe_buf_pin, .release = page_cache_pipe_buf_release, .steal = page_cache_pipe_buf_steal, - .get = page_cache_pipe_buf_get, + .get = generic_pipe_buf_get, }; static int user_page_pipe_buf_steal(struct pipe_inode_info *pipe, struct pipe_buffer *buf) { - return 1; + if (!(buf->flags & PIPE_BUF_FLAG_GIFT)) + return 1; + + buf->flags |= PIPE_BUF_FLAG_LRU; + return generic_pipe_buf_steal(pipe, buf); } static struct pipe_buf_operations user_page_pipe_buf_ops = { .can_merge = 0, - .map = user_page_pipe_buf_map, - .unmap = user_page_pipe_buf_unmap, + .map = generic_pipe_buf_map, + .unmap = generic_pipe_buf_unmap, + .pin = generic_pipe_buf_pin, .release = page_cache_pipe_buf_release, .steal = user_page_pipe_buf_steal, - .get = page_cache_pipe_buf_get, + .get = generic_pipe_buf_get, }; /* @@ -210,6 +189,9 @@ static ssize_t splice_to_pipe(struct pipe_inode_info *pipe, buf->offset = spd->partial[page_nr].offset; buf->len = spd->partial[page_nr].len; buf->ops = spd->ops; + if (spd->flags & SPLICE_F_GIFT) + buf->flags |= PIPE_BUF_FLAG_GIFT; + pipe->nrbufs++; page_nr++; ret += buf->len; @@ -279,7 +261,7 @@ __generic_file_splice_read(struct file *in, loff_t *ppos, pgoff_t index, end_index; loff_t isize; size_t total_len; - int error; + int error, page_nr; struct splice_pipe_desc spd = { .pages = pages, .partial = partial, @@ -299,47 +281,83 @@ __generic_file_splice_read(struct file *in, loff_t *ppos, * read-ahead if this is a non-zero offset (we are likely doing small * chunk splice and the page is already there) for a single page. */ - if (!loff || spd.nr_pages > 1) - do_page_cache_readahead(mapping, in, index, spd.nr_pages); + if (!loff || nr_pages > 1) + page_cache_readahead(mapping, &in->f_ra, in, index, nr_pages); /* * Now fill in the holes: */ error = 0; total_len = 0; - for (spd.nr_pages = 0; spd.nr_pages < nr_pages; spd.nr_pages++, index++) { - unsigned int this_len; - if (!len) - break; + /* + * Lookup the (hopefully) full range of pages we need. + */ + spd.nr_pages = find_get_pages_contig(mapping, index, nr_pages, pages); + /* + * If find_get_pages_contig() returned fewer pages than we needed, + * allocate the rest. + */ + index += spd.nr_pages; + while (spd.nr_pages < nr_pages) { /* - * this_len is the max we'll use from this page - */ - this_len = min_t(unsigned long, len, PAGE_CACHE_SIZE - loff); -find_page: - /* - * lookup the page for this index + * Page could be there, find_get_pages_contig() breaks on + * the first hole. */ page = find_get_page(mapping, index); if (!page) { /* - * page didn't exist, allocate one + * Make sure the read-ahead engine is notified + * about this failure. + */ + handle_ra_miss(mapping, &in->f_ra, index); + + /* + * page didn't exist, allocate one. */ page = page_cache_alloc_cold(mapping); if (!page) break; error = add_to_page_cache_lru(page, mapping, index, - mapping_gfp_mask(mapping)); + mapping_gfp_mask(mapping)); if (unlikely(error)) { page_cache_release(page); + if (error == -EEXIST) + continue; break; } - - goto readpage; + /* + * add_to_page_cache() locks the page, unlock it + * to avoid convoluting the logic below even more. + */ + unlock_page(page); } + pages[spd.nr_pages++] = page; + index++; + } + + /* + * Now loop over the map and see if we need to start IO on any + * pages, fill in the partial map, etc. + */ + index = *ppos >> PAGE_CACHE_SHIFT; + nr_pages = spd.nr_pages; + spd.nr_pages = 0; + for (page_nr = 0; page_nr < nr_pages; page_nr++) { + unsigned int this_len; + + if (!len) + break; + + /* + * this_len is the max we'll use from this page + */ + this_len = min_t(unsigned long, len, PAGE_CACHE_SIZE - loff); + page = pages[page_nr]; + /* * If the page isn't uptodate, we may need to start io on it */ @@ -360,7 +378,6 @@ find_page: */ if (!page->mapping) { unlock_page(page); - page_cache_release(page); break; } /* @@ -371,16 +388,20 @@ find_page: goto fill_it; } -readpage: /* * need to read in the page */ error = mapping->a_ops->readpage(in, page); - if (unlikely(error)) { - page_cache_release(page); + /* + * We really should re-lookup the page here, + * but it complicates things a lot. Instead + * lets just do what we already stored, and + * we'll get it the next time we are called. + */ if (error == AOP_TRUNCATED_PAGE) - goto find_page; + error = 0; + break; } @@ -389,10 +410,8 @@ readpage: */ isize = i_size_read(mapping->host); end_index = (isize - 1) >> PAGE_CACHE_SHIFT; - if (unlikely(!isize || index > end_index)) { - page_cache_release(page); + if (unlikely(!isize || index > end_index)) break; - } /* * if this is the last page, see if we need to shrink @@ -400,27 +419,33 @@ readpage: */ if (end_index == index) { loff = PAGE_CACHE_SIZE - (isize & ~PAGE_CACHE_MASK); - if (total_len + loff > isize) { - page_cache_release(page); + if (total_len + loff > isize) break; - } /* * force quit after adding this page */ - nr_pages = spd.nr_pages; + len = this_len; this_len = min(this_len, loff); loff = 0; } } fill_it: - pages[spd.nr_pages] = page; - partial[spd.nr_pages].offset = loff; - partial[spd.nr_pages].len = this_len; + partial[page_nr].offset = loff; + partial[page_nr].len = this_len; len -= this_len; total_len += this_len; loff = 0; + spd.nr_pages++; + index++; } + /* + * Release any pages at the end, if we quit early. 'i' is how far + * we got, 'nr_pages' is how many pages are in the map. + */ + while (page_nr < nr_pages) + page_cache_release(pages[page_nr++]); + if (spd.nr_pages) return splice_to_pipe(pipe, &spd); @@ -477,31 +502,21 @@ EXPORT_SYMBOL(generic_file_splice_read); * Send 'sd->len' bytes to socket from 'sd->file' at position 'sd->pos' * using sendpage(). Return the number of bytes sent. */ -static int pipe_to_sendpage(struct pipe_inode_info *info, +static int pipe_to_sendpage(struct pipe_inode_info *pipe, struct pipe_buffer *buf, struct splice_desc *sd) { struct file *file = sd->file; loff_t pos = sd->pos; - ssize_t ret; - void *ptr; - int more; - - /* - * Sub-optimal, but we are limited by the pipe ->map. We don't - * need a kmap'ed buffer here, we just want to make sure we - * have the page pinned if the pipe page originates from the - * page cache. - */ - ptr = buf->ops->map(file, info, buf); - if (IS_ERR(ptr)) - return PTR_ERR(ptr); + int ret, more; - more = (sd->flags & SPLICE_F_MORE) || sd->len < sd->total_len; + ret = buf->ops->pin(pipe, buf); + if (!ret) { + more = (sd->flags & SPLICE_F_MORE) || sd->len < sd->total_len; - ret = file->f_op->sendpage(file, buf->page, buf->offset, sd->len, - &pos, more); + ret = file->f_op->sendpage(file, buf->page, buf->offset, + sd->len, &pos, more); + } - buf->ops->unmap(info, buf); return ret; } @@ -525,7 +540,7 @@ static int pipe_to_sendpage(struct pipe_inode_info *info, * SPLICE_F_MOVE isn't set, or we cannot move the page, we simply create * a new page in the output file page cache and fill/dirty that. */ -static int pipe_to_file(struct pipe_inode_info *info, struct pipe_buffer *buf, +static int pipe_to_file(struct pipe_inode_info *pipe, struct pipe_buffer *buf, struct splice_desc *sd) { struct file *file = sd->file; @@ -534,15 +549,14 @@ static int pipe_to_file(struct pipe_inode_info *info, struct pipe_buffer *buf, unsigned int offset, this_len; struct page *page; pgoff_t index; - char *src; int ret; /* * make sure the data in this buffer is uptodate */ - src = buf->ops->map(file, info, buf); - if (IS_ERR(src)) - return PTR_ERR(src); + ret = buf->ops->pin(pipe, buf); + if (unlikely(ret)) + return ret; index = sd->pos >> PAGE_CACHE_SHIFT; offset = sd->pos & ~PAGE_CACHE_MASK; @@ -552,20 +566,25 @@ static int pipe_to_file(struct pipe_inode_info *info, struct pipe_buffer *buf, this_len = PAGE_CACHE_SIZE - offset; /* - * Reuse buf page, if SPLICE_F_MOVE is set. + * Reuse buf page, if SPLICE_F_MOVE is set and we are doing a full + * page. */ - if (sd->flags & SPLICE_F_MOVE) { + if ((sd->flags & SPLICE_F_MOVE) && this_len == PAGE_CACHE_SIZE) { /* - * If steal succeeds, buf->page is now pruned from the vm - * side (LRU and page cache) and we can reuse it. The page - * will also be looked on successful return. + * If steal succeeds, buf->page is now pruned from the + * pagecache and we can reuse it. The page will also be + * locked on successful return. */ - if (buf->ops->steal(info, buf)) + if (buf->ops->steal(pipe, buf)) goto find_page; page = buf->page; - if (add_to_page_cache(page, mapping, index, gfp_mask)) + if (add_to_page_cache(page, mapping, index, gfp_mask)) { + unlock_page(page); goto find_page; + } + + page_cache_get(page); if (!(buf->flags & PIPE_BUF_FLAG_LRU)) lru_cache_add(page); @@ -619,40 +638,55 @@ find_page: } ret = mapping->a_ops->prepare_write(file, page, offset, offset+this_len); - if (ret == AOP_TRUNCATED_PAGE) { + if (unlikely(ret)) { + loff_t isize = i_size_read(mapping->host); + + if (ret != AOP_TRUNCATED_PAGE) + unlock_page(page); page_cache_release(page); - goto find_page; - } else if (ret) + if (ret == AOP_TRUNCATED_PAGE) + goto find_page; + + /* + * prepare_write() may have instantiated a few blocks + * outside i_size. Trim these off again. + */ + if (sd->pos + this_len > isize) + vmtruncate(mapping->host, isize); + goto out; + } - if (!(buf->flags & PIPE_BUF_FLAG_STOLEN)) { - char *dst = kmap_atomic(page, KM_USER0); + if (buf->page != page) { + /* + * Careful, ->map() uses KM_USER0! + */ + char *src = buf->ops->map(pipe, buf, 1); + char *dst = kmap_atomic(page, KM_USER1); memcpy(dst + offset, src + buf->offset, this_len); flush_dcache_page(page); - kunmap_atomic(dst, KM_USER0); + kunmap_atomic(dst, KM_USER1); + buf->ops->unmap(pipe, buf, src); } ret = mapping->a_ops->commit_write(file, page, offset, offset+this_len); - if (ret == AOP_TRUNCATED_PAGE) { + if (!ret) { + /* + * Return the number of bytes written and mark page as + * accessed, we are now done! + */ + ret = this_len; + mark_page_accessed(page); + balance_dirty_pages_ratelimited(mapping); + } else if (ret == AOP_TRUNCATED_PAGE) { page_cache_release(page); goto find_page; - } else if (ret) - goto out; - - /* - * Return the number of bytes written. - */ - ret = this_len; - mark_page_accessed(page); - balance_dirty_pages_ratelimited(mapping); + } out: - if (!(buf->flags & PIPE_BUF_FLAG_STOLEN)) - page_cache_release(page); - + page_cache_release(page); unlock_page(page); out_nomem: - buf->ops->unmap(info, buf); return ret; } @@ -1060,7 +1094,7 @@ static long do_splice(struct file *in, loff_t __user *off_in, */ static int get_iovec_page_array(const struct iovec __user *iov, unsigned int nr_vecs, struct page **pages, - struct partial_page *partial) + struct partial_page *partial, int aligned) { int buffers = 0, error = 0; @@ -1100,6 +1134,15 @@ static int get_iovec_page_array(const struct iovec __user *iov, * in the user pages. */ off = (unsigned long) base & ~PAGE_MASK; + + /* + * If asked for alignment, the offset must be zero and the + * length a multiple of the PAGE_SIZE. + */ + error = -EINVAL; + if (aligned && (off || len & ~PAGE_MASK)) + break; + npages = (off + len + PAGE_SIZE - 1) >> PAGE_SHIFT; if (npages > PIPE_BUFFERS - buffers) npages = PIPE_BUFFERS - buffers; @@ -1115,7 +1158,7 @@ static int get_iovec_page_array(const struct iovec __user *iov, * Fill this contiguous range into the partial page map. */ for (i = 0; i < error; i++) { - const int plen = min_t(size_t, len, PAGE_SIZE) - off; + const int plen = min_t(size_t, len, PAGE_SIZE - off); partial[buffers].offset = off; partial[buffers].len = plen; @@ -1193,7 +1236,8 @@ static long do_vmsplice(struct file *file, const struct iovec __user *iov, else if (unlikely(!nr_segs)) return 0; - spd.nr_pages = get_iovec_page_array(iov, nr_segs, pages, partial); + spd.nr_pages = get_iovec_page_array(iov, nr_segs, pages, partial, + flags & SPLICE_F_GIFT); if (spd.nr_pages <= 0) return spd.nr_pages; @@ -1301,6 +1345,12 @@ static int link_pipe(struct pipe_inode_info *ipipe, obuf = opipe->bufs + nbuf; *obuf = *ibuf; + /* + * Don't inherit the gift flag, we need to + * prevent multiple steals of this page. + */ + obuf->flags &= ~PIPE_BUF_FLAG_GIFT; + if (obuf->len > len) obuf->len = len; diff --git a/fs/stat.c b/fs/stat.c index 9948cc1685a..0f282face32 100644 --- a/fs/stat.c +++ b/fs/stat.c @@ -261,7 +261,7 @@ asmlinkage long sys_newlstat(char __user *filename, struct stat __user *statbuf) return error; } -#ifndef __ARCH_WANT_STAT64 +#if !defined(__ARCH_WANT_STAT64) || defined(__ARCH_WANT_SYS_NEWFSTATAT) asmlinkage long sys_newfstatat(int dfd, char __user *filename, struct stat __user *statbuf, int flag) { diff --git a/fs/xfs/xfs_alloc.c b/fs/xfs/xfs_alloc.c index 64ee07db0d5..8558226281c 100644 --- a/fs/xfs/xfs_alloc.c +++ b/fs/xfs/xfs_alloc.c @@ -1942,8 +1942,10 @@ xfs_alloc_fix_freelist( /* * Allocate as many blocks as possible at once. */ - if ((error = xfs_alloc_ag_vextent(&targs))) + if ((error = xfs_alloc_ag_vextent(&targs))) { + xfs_trans_brelse(tp, agflbp); return error; + } /* * Stop if we run out. Won't happen if callers are obeying * the restrictions correctly. Can happen for free calls @@ -1960,6 +1962,7 @@ xfs_alloc_fix_freelist( return error; } } + xfs_trans_brelse(tp, agflbp); args->agbp = agbp; return 0; } diff --git a/fs/xfs/xfs_rename.c b/fs/xfs/xfs_rename.c index 81a05cfd77d..1f148762eb2 100644 --- a/fs/xfs/xfs_rename.c +++ b/fs/xfs/xfs_rename.c @@ -316,6 +316,18 @@ xfs_rename( } } + /* + * If we are using project inheritance, we only allow renames + * into our tree when the project IDs are the same; else the + * tree quota mechanism would be circumvented. + */ + if (unlikely((target_dp->i_d.di_flags & XFS_DIFLAG_PROJINHERIT) && + (target_dp->i_d.di_projid != src_ip->i_d.di_projid))) { + error = XFS_ERROR(EXDEV); + xfs_rename_unlock4(inodes, XFS_ILOCK_SHARED); + goto rele_return; + } + new_parent = (src_dp != target_dp); src_is_directory = ((src_ip->i_d.di_mode & S_IFMT) == S_IFDIR); diff --git a/fs/xfs/xfs_vfsops.c b/fs/xfs/xfs_vfsops.c index f0e09ca1413..36ea1b2094f 100644 --- a/fs/xfs/xfs_vfsops.c +++ b/fs/xfs/xfs_vfsops.c @@ -669,31 +669,22 @@ xfs_mntupdate( xfs_mount_t *mp = XFS_BHVTOM(bdp); int error; - if (args->flags & XFSMNT_BARRIER) - mp->m_flags |= XFS_MOUNT_BARRIER; - else - mp->m_flags &= ~XFS_MOUNT_BARRIER; - - if ((vfsp->vfs_flag & VFS_RDONLY) && - !(*flags & MS_RDONLY)) { - vfsp->vfs_flag &= ~VFS_RDONLY; - - if (args->flags & XFSMNT_BARRIER) + if (!(*flags & MS_RDONLY)) { /* rw/ro -> rw */ + if (vfsp->vfs_flag & VFS_RDONLY) + vfsp->vfs_flag &= ~VFS_RDONLY; + if (args->flags & XFSMNT_BARRIER) { + mp->m_flags |= XFS_MOUNT_BARRIER; xfs_mountfs_check_barriers(mp); - } - - if (!(vfsp->vfs_flag & VFS_RDONLY) && - (*flags & MS_RDONLY)) { + } else { + mp->m_flags &= ~XFS_MOUNT_BARRIER; + } + } else if (!(vfsp->vfs_flag & VFS_RDONLY)) { /* rw -> ro */ VFS_SYNC(vfsp, SYNC_FSDATA|SYNC_BDFLUSH|SYNC_ATTR, NULL, error); - xfs_quiesce_fs(mp); - - /* Ok now write out an unmount record */ xfs_log_unmount_write(mp); xfs_unmountfs_writesb(mp); vfsp->vfs_flag |= VFS_RDONLY; } - return 0; } diff --git a/fs/xfs/xfs_vnodeops.c b/fs/xfs/xfs_vnodeops.c index fa71b305ba5..7027ae68ee3 100644 --- a/fs/xfs/xfs_vnodeops.c +++ b/fs/xfs/xfs_vnodeops.c @@ -2663,7 +2663,7 @@ xfs_link( */ if (unlikely((tdp->i_d.di_flags & XFS_DIFLAG_PROJINHERIT) && (tdp->i_d.di_projid != sip->i_d.di_projid))) { - error = XFS_ERROR(EPERM); + error = XFS_ERROR(EXDEV); goto error_return; } diff --git a/include/asm-arm/arch-aaec2000/debug-macro.S b/include/asm-arm/arch-aaec2000/debug-macro.S index e4f1fa539a7..7b1fce021d8 100644 --- a/include/asm-arm/arch-aaec2000/debug-macro.S +++ b/include/asm-arm/arch-aaec2000/debug-macro.S @@ -9,6 +9,7 @@ * published by the Free Software Foundation. */ +#include "hardware.h" .macro addruart,rx mrc p15, 0, \rx, c1, c0 tst \rx, #1 @ MMU enabled? diff --git a/include/asm-arm/arch-aaec2000/entry-macro.S b/include/asm-arm/arch-aaec2000/entry-macro.S index df31313ab07..1eb3503bd16 100644 --- a/include/asm-arm/arch-aaec2000/entry-macro.S +++ b/include/asm-arm/arch-aaec2000/entry-macro.S @@ -10,6 +10,7 @@ * published by the Free Software Foundation. * */ +#include <asm/arch/irqs.h> .macro disable_fiq .endm diff --git a/include/asm-arm/arch-imx/debug-macro.S b/include/asm-arm/arch-imx/debug-macro.S index 83f552f7bcc..c611871643a 100644 --- a/include/asm-arm/arch-imx/debug-macro.S +++ b/include/asm-arm/arch-imx/debug-macro.S @@ -16,7 +16,7 @@ tst \rx, #1 @ MMU enabled? moveq \rx, #0x00000000 @ physical movne \rx, #0xe0000000 @ virtual - orr \rx, \rx, #0x00200000 + orreq \rx, \rx, #0x00200000 @ physical orr \rx, \rx, #0x00006000 @ UART1 offset .endm diff --git a/include/asm-arm/arch-imx/imx-uart.h b/include/asm-arm/arch-imx/imx-uart.h new file mode 100644 index 00000000000..3a685e1780e --- /dev/null +++ b/include/asm-arm/arch-imx/imx-uart.h @@ -0,0 +1,10 @@ +#ifndef ASMARM_ARCH_UART_H +#define ASMARM_ARCH_UART_H + +#define IMXUART_HAVE_RTSCTS (1<<0) + +struct imxuart_platform_data { + unsigned int flags; +}; + +#endif diff --git a/include/asm-arm/arch-ixp4xx/io.h b/include/asm-arm/arch-ixp4xx/io.h index 942b622455b..b59520e56fc 100644 --- a/include/asm-arm/arch-ixp4xx/io.h +++ b/include/asm-arm/arch-ixp4xx/io.h @@ -260,6 +260,12 @@ out: #endif +#ifndef CONFIG_PCI + +#define __io(v) v + +#else + /* * IXP4xx does not have a transparent cpu -> PCI I/O translation * window. Instead, it has a set of registers that must be tweaked @@ -578,6 +584,7 @@ __ixp4xx_iowrite32_rep(void __iomem *addr, const void *vaddr, u32 count) #define ioport_map(port, nr) ((void __iomem*)(port + PIO_OFFSET)) #define ioport_unmap(addr) +#endif // !CONFIG_PCI #endif // __ASM_ARM_ARCH_IO_H diff --git a/include/asm-arm/arch-ixp4xx/memory.h b/include/asm-arm/arch-ixp4xx/memory.h index ee211d28a3e..af9667b57ab 100644 --- a/include/asm-arm/arch-ixp4xx/memory.h +++ b/include/asm-arm/arch-ixp4xx/memory.h @@ -14,7 +14,7 @@ */ #define PHYS_OFFSET UL(0x00000000) -#ifndef __ASSEMBLY__ +#if !defined(__ASSEMBLY__) && defined(CONFIG_PCI) void ixp4xx_adjust_zones(int node, unsigned long *size, unsigned long *holes); diff --git a/include/asm-arm/arch-pxa/dma.h b/include/asm-arm/arch-pxa/dma.h index 3e88a2a02a0..a008150abc5 100644 --- a/include/asm-arm/arch-pxa/dma.h +++ b/include/asm-arm/arch-pxa/dma.h @@ -24,27 +24,29 @@ typedef struct pxa_dma_desc { volatile u32 dcmd; /* DCMD value for the current transfer */ } pxa_dma_desc; +typedef enum { + DMA_PRIO_HIGH = 0, + DMA_PRIO_MEDIUM = 1, + DMA_PRIO_LOW = 2 +} pxa_dma_prio; + #if defined(CONFIG_PXA27x) #define PXA_DMA_CHANNELS 32 -#define PXA_DMA_NBCH(prio) ((prio == DMA_PRIO_LOW) ? 16 : 8) -typedef enum { - DMA_PRIO_HIGH = 0, - DMA_PRIO_MEDIUM = 8, - DMA_PRIO_LOW = 16 -} pxa_dma_prio; +#define pxa_for_each_dma_prio(ch, prio) \ +for ( \ + ch = prio * 4; \ + ch != (4 << prio) + 16; \ + ch = (ch + 1 == (4 << prio)) ? (prio * 4 + 16) : (ch + 1) \ +) #elif defined(CONFIG_PXA25x) #define PXA_DMA_CHANNELS 16 -#define PXA_DMA_NBCH(prio) ((prio == DMA_PRIO_LOW) ? 8 : 4) -typedef enum { - DMA_PRIO_HIGH = 0, - DMA_PRIO_MEDIUM = 4, - DMA_PRIO_LOW = 8 -} pxa_dma_prio; +#define pxa_for_each_dma_prio(ch, prio) \ + for (ch = prio * 4; ch != (4 << prio); ch++) #endif diff --git a/include/asm-arm/bug.h b/include/asm-arm/bug.h index 7fb02138f58..5ab8216f520 100644 --- a/include/asm-arm/bug.h +++ b/include/asm-arm/bug.h @@ -2,6 +2,7 @@ #define _ASMARM_BUG_H #include <linux/config.h> +#include <linux/stddef.h> #ifdef CONFIG_BUG #ifdef CONFIG_DEBUG_BUGVERBOSE diff --git a/include/asm-arm/unistd.h b/include/asm-arm/unistd.h index ee8dfea549b..cbf39a56dbe 100644 --- a/include/asm-arm/unistd.h +++ b/include/asm-arm/unistd.h @@ -363,7 +363,7 @@ /* * The following syscalls are obsolete and no longer available for EABI. */ -#if defined(__ARM_EABI__) +#if defined(__ARM_EABI__) && !defined(__KERNEL__) #undef __NR_time #undef __NR_umount #undef __NR_stime @@ -410,7 +410,8 @@ type name(void) { \ __asm__ __volatile__ ( \ __syscall(name) \ : "=r" (__res_r0) \ - : __SYS_REG_LIST() ); \ + : __SYS_REG_LIST() \ + : "memory" ); \ __res = __res_r0; \ __syscall_return(type,__res); \ } @@ -424,7 +425,8 @@ type name(type1 arg1) { \ __asm__ __volatile__ ( \ __syscall(name) \ : "=r" (__res_r0) \ - : __SYS_REG_LIST( "0" (__r0) ) ); \ + : __SYS_REG_LIST( "0" (__r0) ) \ + : "memory" ); \ __res = __res_r0; \ __syscall_return(type,__res); \ } @@ -439,7 +441,8 @@ type name(type1 arg1,type2 arg2) { \ __asm__ __volatile__ ( \ __syscall(name) \ : "=r" (__res_r0) \ - : __SYS_REG_LIST( "0" (__r0), "r" (__r1) ) ); \ + : __SYS_REG_LIST( "0" (__r0), "r" (__r1) ) \ + : "memory" ); \ __res = __res_r0; \ __syscall_return(type,__res); \ } @@ -456,7 +459,8 @@ type name(type1 arg1,type2 arg2,type3 arg3) { \ __asm__ __volatile__ ( \ __syscall(name) \ : "=r" (__res_r0) \ - : __SYS_REG_LIST( "0" (__r0), "r" (__r1), "r" (__r2) ) ); \ + : __SYS_REG_LIST( "0" (__r0), "r" (__r1), "r" (__r2) ) \ + : "memory" ); \ __res = __res_r0; \ __syscall_return(type,__res); \ } @@ -474,7 +478,8 @@ type name(type1 arg1, type2 arg2, type3 arg3, type4 arg4) { \ __asm__ __volatile__ ( \ __syscall(name) \ : "=r" (__res_r0) \ - : __SYS_REG_LIST( "0" (__r0), "r" (__r1), "r" (__r2), "r" (__r3) ) ); \ + : __SYS_REG_LIST( "0" (__r0), "r" (__r1), "r" (__r2), "r" (__r3) ) \ + : "memory" ); \ __res = __res_r0; \ __syscall_return(type,__res); \ } @@ -494,7 +499,8 @@ type name(type1 arg1, type2 arg2, type3 arg3, type4 arg4, type5 arg5) { \ __syscall(name) \ : "=r" (__res_r0) \ : __SYS_REG_LIST( "0" (__r0), "r" (__r1), "r" (__r2), \ - "r" (__r3), "r" (__r4) ) ); \ + "r" (__r3), "r" (__r4) ) \ + : "memory" ); \ __res = __res_r0; \ __syscall_return(type,__res); \ } @@ -514,7 +520,8 @@ type name(type1 arg1, type2 arg2, type3 arg3, type4 arg4, type5 arg5, type6 arg6 __syscall(name) \ : "=r" (__res_r0) \ : __SYS_REG_LIST( "0" (__r0), "r" (__r1), "r" (__r2), \ - "r" (__r3), "r" (__r4), "r" (__r5) ) ); \ + "r" (__r3), "r" (__r4), "r" (__r5) ) \ + : "memory" ); \ __res = __res_r0; \ __syscall_return(type,__res); \ } diff --git a/include/asm-i386/i387.h b/include/asm-i386/i387.h index 7b1f01191e7..bc1d6edae1e 100644 --- a/include/asm-i386/i387.h +++ b/include/asm-i386/i387.h @@ -58,13 +58,13 @@ static inline void __save_init_fpu( struct task_struct *tsk ) alternative_input( "fnsave %[fx] ;fwait;" GENERIC_NOP8 GENERIC_NOP4, "fxsave %[fx]\n" - "bt $7,%[fsw] ; jc 1f ; fnclex\n1:", + "bt $7,%[fsw] ; jnc 1f ; fnclex\n1:", X86_FEATURE_FXSR, [fx] "m" (tsk->thread.i387.fxsave), [fsw] "m" (tsk->thread.i387.fxsave.swd) : "memory"); /* AMD K7/K8 CPUs don't save/restore FDP/FIP/FOP unless an exception is pending. Clear the x87 state here by setting it to fixed - values. __per_cpu_offset[0] is a random variable that should be in L1 */ + values. safe_address is a random variable that should be in L1 */ alternative_input( GENERIC_NOP8 GENERIC_NOP2, "emms\n\t" /* clear stack tags */ diff --git a/include/asm-i386/io_apic.h b/include/asm-i386/io_apic.h index 51c4e5fe606..d92e253f7f6 100644 --- a/include/asm-i386/io_apic.h +++ b/include/asm-i386/io_apic.h @@ -200,6 +200,7 @@ extern int io_apic_get_unique_id (int ioapic, int apic_id); extern int io_apic_get_version (int ioapic); extern int io_apic_get_redir_entries (int ioapic); extern int io_apic_set_pci_routing (int ioapic, int pin, int irq, int edge_level, int active_high_low); +extern int timer_uses_ioapic_pin_0; #endif /* CONFIG_ACPI */ extern int (*ioapic_renumber_irq)(int ioapic, int irq); diff --git a/include/asm-i386/pgtable-2level.h b/include/asm-i386/pgtable-2level.h index 27bde973abc..2756d4b04c2 100644 --- a/include/asm-i386/pgtable-2level.h +++ b/include/asm-i386/pgtable-2level.h @@ -18,6 +18,9 @@ #define set_pte_atomic(pteptr, pteval) set_pte(pteptr,pteval) #define set_pmd(pmdptr, pmdval) (*(pmdptr) = (pmdval)) +#define pte_clear(mm,addr,xp) do { set_pte_at(mm, addr, xp, __pte(0)); } while (0) +#define pmd_clear(xp) do { set_pmd(xp, __pmd(0)); } while (0) + #define ptep_get_and_clear(mm,addr,xp) __pte(xchg(&(xp)->pte_low, 0)) #define pte_same(a, b) ((a).pte_low == (b).pte_low) #define pte_page(x) pfn_to_page(pte_pfn(x)) diff --git a/include/asm-i386/pgtable-3level.h b/include/asm-i386/pgtable-3level.h index 36a5aa63cbb..dccb1b3337a 100644 --- a/include/asm-i386/pgtable-3level.h +++ b/include/asm-i386/pgtable-3level.h @@ -85,6 +85,26 @@ static inline void pud_clear (pud_t * pud) { } #define pmd_offset(pud, address) ((pmd_t *) pud_page(*(pud)) + \ pmd_index(address)) +/* + * For PTEs and PDEs, we must clear the P-bit first when clearing a page table + * entry, so clear the bottom half first and enforce ordering with a compiler + * barrier. + */ +static inline void pte_clear(struct mm_struct *mm, unsigned long addr, pte_t *ptep) +{ + ptep->pte_low = 0; + smp_wmb(); + ptep->pte_high = 0; +} + +static inline void pmd_clear(pmd_t *pmd) +{ + u32 *tmp = (u32 *)pmd; + *tmp = 0; + smp_wmb(); + *(tmp + 1) = 0; +} + static inline pte_t ptep_get_and_clear(struct mm_struct *mm, unsigned long addr, pte_t *ptep) { pte_t res; diff --git a/include/asm-i386/pgtable.h b/include/asm-i386/pgtable.h index ee056c41a9f..672c3f76b9d 100644 --- a/include/asm-i386/pgtable.h +++ b/include/asm-i386/pgtable.h @@ -204,12 +204,10 @@ extern unsigned long long __PAGE_KERNEL, __PAGE_KERNEL_EXEC; extern unsigned long pg0[]; #define pte_present(x) ((x).pte_low & (_PAGE_PRESENT | _PAGE_PROTNONE)) -#define pte_clear(mm,addr,xp) do { set_pte_at(mm, addr, xp, __pte(0)); } while (0) /* To avoid harmful races, pmd_none(x) should check only the lower when PAE */ #define pmd_none(x) (!(unsigned long)pmd_val(x)) #define pmd_present(x) (pmd_val(x) & _PAGE_PRESENT) -#define pmd_clear(xp) do { set_pmd(xp, __pmd(0)); } while (0) #define pmd_bad(x) ((pmd_val(x) & (~PAGE_MASK & ~_PAGE_USER)) != _KERNPG_TABLE) @@ -268,7 +266,7 @@ static inline pte_t ptep_get_and_clear_full(struct mm_struct *mm, unsigned long pte_t pte; if (full) { pte = *ptep; - *ptep = __pte(0); + pte_clear(mm, addr, ptep); } else { pte = ptep_get_and_clear(mm, addr, ptep); } diff --git a/include/asm-ia64/acpi.h b/include/asm-ia64/acpi.h index d734585a23c..09a5dd0e44a 100644 --- a/include/asm-ia64/acpi.h +++ b/include/asm-ia64/acpi.h @@ -110,9 +110,8 @@ extern void prefill_possible_map(void); extern int additional_cpus; #ifdef CONFIG_ACPI_NUMA -/* Proximity bitmap length; _PXM is at most 255 (8 bit)*/ -#ifdef CONFIG_IA64_NR_NODES -#define MAX_PXM_DOMAINS CONFIG_IA64_NR_NODES +#if MAX_NUMNODES > 256 +#define MAX_PXM_DOMAINS MAX_NUMNODES #else #define MAX_PXM_DOMAINS (256) #endif diff --git a/include/asm-ia64/bitops.h b/include/asm-ia64/bitops.h index 90921e16279..6cc517e212a 100644 --- a/include/asm-ia64/bitops.h +++ b/include/asm-ia64/bitops.h @@ -11,7 +11,6 @@ #include <linux/compiler.h> #include <linux/types.h> -#include <asm/bitops.h> #include <asm/intrinsics.h> /** diff --git a/include/asm-ia64/machvec.h b/include/asm-ia64/machvec.h index c3e4ed8a3e1..a9c995a86c2 100644 --- a/include/asm-ia64/machvec.h +++ b/include/asm-ia64/machvec.h @@ -347,9 +347,11 @@ extern ia64_mv_dma_supported swiotlb_dma_supported; #endif #ifndef platform_pci_legacy_read # define platform_pci_legacy_read ia64_pci_legacy_read +extern int ia64_pci_legacy_read(struct pci_bus *bus, u16 port, u32 *val, u8 size); #endif #ifndef platform_pci_legacy_write # define platform_pci_legacy_write ia64_pci_legacy_write +extern int ia64_pci_legacy_write(struct pci_bus *bus, u16 port, u32 val, u8 size); #endif #ifndef platform_inb # define platform_inb __ia64_inb diff --git a/include/asm-ia64/sn/sn2/sn_hwperf.h b/include/asm-ia64/sn/sn2/sn_hwperf.h index 291ef3d69da..e61ebac38cd 100644 --- a/include/asm-ia64/sn/sn2/sn_hwperf.h +++ b/include/asm-ia64/sn/sn2/sn_hwperf.h @@ -45,8 +45,12 @@ struct sn_hwperf_object_info { #define SN_HWPERF_IS_NODE(x) ((x) && strstr((x)->name, "SHub")) #define SN_HWPERF_IS_NODE_SHUB2(x) ((x) && strstr((x)->name, "SHub 2.")) #define SN_HWPERF_IS_IONODE(x) ((x) && strstr((x)->name, "TIO")) -#define SN_HWPERF_IS_ROUTER(x) ((x) && strstr((x)->name, "Router")) #define SN_HWPERF_IS_NL3ROUTER(x) ((x) && strstr((x)->name, "NL3Router")) +#define SN_HWPERF_IS_NL4ROUTER(x) ((x) && strstr((x)->name, "NL4Router")) +#define SN_HWPERF_IS_OLDROUTER(x) ((x) && strstr((x)->name, "Router")) +#define SN_HWPERF_IS_ROUTER(x) (SN_HWPERF_IS_NL3ROUTER(x) || \ + SN_HWPERF_IS_NL4ROUTER(x) || \ + SN_HWPERF_IS_OLDROUTER(x)) #define SN_HWPERF_FOREIGN(x) ((x) && !(x)->sn_hwp_this_part && !(x)->sn_hwp_is_shared) #define SN_HWPERF_SAME_OBJTYPE(x,y) ((SN_HWPERF_IS_NODE(x) && SN_HWPERF_IS_NODE(y)) ||\ (SN_HWPERF_IS_IONODE(x) && SN_HWPERF_IS_IONODE(y)) ||\ diff --git a/include/asm-ia64/sn/sn_sal.h b/include/asm-ia64/sn/sn_sal.h index bf4cc867a69..51aca022cf3 100644 --- a/include/asm-ia64/sn/sn_sal.h +++ b/include/asm-ia64/sn/sn_sal.h @@ -8,7 +8,7 @@ * License. See the file "COPYING" in the main directory of this archive * for more details. * - * Copyright (c) 2000-2005 Silicon Graphics, Inc. All rights reserved. + * Copyright (c) 2000-2006 Silicon Graphics, Inc. All rights reserved. */ @@ -85,6 +85,7 @@ #define SN_SAL_GET_PROM_FEATURE_SET 0x02000065 #define SN_SAL_SET_OS_FEATURE_SET 0x02000066 +#define SN_SAL_INJECT_ERROR 0x02000067 /* * Service-specific constants @@ -705,10 +706,8 @@ static inline int sn_change_memprotect(u64 paddr, u64 len, u64 perms, u64 *nasid_array) { struct ia64_sal_retval ret_stuff; - int cnodeid; unsigned long irq_flags; - cnodeid = nasid_to_cnodeid(get_node_number(paddr)); local_irq_save(irq_flags); ia64_sal_oemcall_nolock(&ret_stuff, SN_SAL_MEMPROTECT, paddr, len, (u64)nasid_array, perms, 0, 0, 0); @@ -1140,4 +1139,16 @@ ia64_sn_set_os_feature(int feature) return rv.status; } +static inline int +sn_inject_error(u64 paddr, u64 *data, u64 *ecc) +{ + struct ia64_sal_retval ret_stuff; + unsigned long irq_flags; + + local_irq_save(irq_flags); + ia64_sal_oemcall_nolock(&ret_stuff, SN_SAL_INJECT_ERROR, paddr, (u64)data, + (u64)ecc, 0, 0, 0, 0); + local_irq_restore(irq_flags); + return ret_stuff.status; +} #endif /* _ASM_IA64_SN_SN_SAL_H */ diff --git a/include/asm-ia64/thread_info.h b/include/asm-ia64/thread_info.h index 56394a2c705..e5392c4d30c 100644 --- a/include/asm-ia64/thread_info.h +++ b/include/asm-ia64/thread_info.h @@ -67,7 +67,7 @@ struct thread_info { #define end_of_stack(p) (unsigned long *)((void *)(p) + IA64_RBS_OFFSET) #define __HAVE_ARCH_TASK_STRUCT_ALLOCATOR -#define alloc_task_struct() ((task_t *)__get_free_pages(GFP_KERNEL, KERNEL_STACK_SIZE_ORDER)) +#define alloc_task_struct() ((task_t *)__get_free_pages(GFP_KERNEL | __GFP_COMP, KERNEL_STACK_SIZE_ORDER)) #define free_task_struct(tsk) free_pages((unsigned long) (tsk), KERNEL_STACK_SIZE_ORDER) #endif /* !__ASSEMBLY */ diff --git a/include/asm-ia64/topology.h b/include/asm-ia64/topology.h index 3ee19dfa46d..616b5ed2aa7 100644 --- a/include/asm-ia64/topology.h +++ b/include/asm-ia64/topology.h @@ -23,6 +23,11 @@ #define PENALTY_FOR_NODE_WITH_CPUS 255 /* + * Distance above which we begin to use zone reclaim + */ +#define RECLAIM_DISTANCE 15 + +/* * Returns the number of the node containing CPU 'cpu' */ #define cpu_to_node(cpu) (int)(cpu_to_node_map[cpu]) diff --git a/include/asm-mips/bitops.h b/include/asm-mips/bitops.h index a1728f8c070..d2f444537e4 100644 --- a/include/asm-mips/bitops.h +++ b/include/asm-mips/bitops.h @@ -467,64 +467,56 @@ static inline unsigned long __ffs(unsigned long word) } /* - * ffs - find first bit set. + * fls - find last bit set. * @word: The word to search * - * Returns 1..SZLONG - * Returns 0 if no bit exists + * This is defined the same way as ffs. + * Note fls(0) = 0, fls(1) = 1, fls(0x80000000) = 32. */ - -static inline unsigned long ffs(unsigned long word) +static inline int fls(int word) { - if (!word) - return 0; + __asm__ ("clz %0, %1" : "=r" (word) : "r" (word)); - return __ffs(word) + 1; + return 32 - word; } -/* - * ffz - find first zero in word. - * @word: The word to search - * - * Undefined if no zero exists, so code should check against ~0UL first. - */ -static inline unsigned long ffz(unsigned long word) +#if defined(CONFIG_64BIT) && defined(CONFIG_CPU_MIPS64) +static inline int fls64(__u64 word) { - return __ffs (~word); + __asm__ ("dclz %0, %1" : "=r" (word) : "r" (word)); + + return 64 - word; } +#else +#include <asm-generic/bitops/fls64.h> +#endif /* - * fls - find last bit set. + * ffs - find first bit set. * @word: The word to search * - * Returns 1..SZLONG - * Returns 0 if no bit exists + * This is defined the same way as + * the libc and compiler builtin ffs routines, therefore + * differs in spirit from the above ffz (man ffs). */ -static inline unsigned long fls(unsigned long word) +static inline int ffs(int word) { -#ifdef CONFIG_CPU_MIPS32 - __asm__ ("clz %0, %1" : "=r" (word) : "r" (word)); - - return 32 - word; -#endif - -#ifdef CONFIG_CPU_MIPS64 - __asm__ ("dclz %0, %1" : "=r" (word) : "r" (word)); + if (!word) + return 0; - return 64 - word; -#endif + return fls(word & -word); } #else #include <asm-generic/bitops/__ffs.h> #include <asm-generic/bitops/ffs.h> -#include <asm-generic/bitops/ffz.h> #include <asm-generic/bitops/fls.h> +#include <asm-generic/bitops/fls64.h> #endif /*defined(CONFIG_CPU_MIPS32) || defined(CONFIG_CPU_MIPS64) */ -#include <asm-generic/bitops/fls64.h> +#include <asm-generic/bitops/ffz.h> #include <asm-generic/bitops/find.h> #ifdef __KERNEL__ diff --git a/include/asm-mips/mips-boards/generic.h b/include/asm-mips/mips-boards/generic.h index 25b6ffc2662..fa8b913cc3e 100644 --- a/include/asm-mips/mips-boards/generic.h +++ b/include/asm-mips/mips-boards/generic.h @@ -67,6 +67,7 @@ #define MIPS_REVISION_CORID_CORE_FPGA2 7 #define MIPS_REVISION_CORID_CORE_FPGAR2 8 #define MIPS_REVISION_CORID_CORE_FPGA3 9 +#define MIPS_REVISION_CORID_CORE_24K 10 /**** Artificial corid defines ****/ /* diff --git a/include/asm-powerpc/cputable.h b/include/asm-powerpc/cputable.h index 4321483cce5..9fcf0162d85 100644 --- a/include/asm-powerpc/cputable.h +++ b/include/asm-powerpc/cputable.h @@ -22,6 +22,7 @@ #define PPC_FEATURE_BOOKE 0x00008000 #define PPC_FEATURE_SMT 0x00004000 #define PPC_FEATURE_ICACHE_SNOOP 0x00002000 +#define PPC_FEATURE_ARCH_2_05 0x00001000 #ifdef __KERNEL__ #ifndef __ASSEMBLY__ @@ -320,6 +321,11 @@ extern void do_cpu_ftr_fixups(unsigned long offset); CPU_FTR_MMCRA | CPU_FTR_SMT | \ CPU_FTR_COHERENT_ICACHE | CPU_FTR_LOCKLESS_TLBIE | \ CPU_FTR_MMCRA_SIHV | CPU_FTR_PURR) +#define CPU_FTRS_POWER6 (CPU_FTR_SPLIT_ID_CACHE | CPU_FTR_USE_TB | \ + CPU_FTR_HPTE_TABLE | CPU_FTR_PPCAS_ARCH_V2 | \ + CPU_FTR_MMCRA | CPU_FTR_SMT | \ + CPU_FTR_COHERENT_ICACHE | CPU_FTR_LOCKLESS_TLBIE | \ + CPU_FTR_PURR | CPU_FTR_CI_LARGE_PAGE) #define CPU_FTRS_CELL (CPU_FTR_SPLIT_ID_CACHE | CPU_FTR_USE_TB | \ CPU_FTR_HPTE_TABLE | CPU_FTR_PPCAS_ARCH_V2 | \ CPU_FTR_ALTIVEC_COMP | CPU_FTR_MMCRA | CPU_FTR_SMT | \ @@ -331,8 +337,8 @@ extern void do_cpu_ftr_fixups(unsigned long offset); #ifdef __powerpc64__ #define CPU_FTRS_POSSIBLE \ (CPU_FTRS_POWER3 | CPU_FTRS_RS64 | CPU_FTRS_POWER4 | \ - CPU_FTRS_PPC970 | CPU_FTRS_POWER5 | CPU_FTRS_CELL | \ - CPU_FTR_CI_LARGE_PAGE) + CPU_FTRS_PPC970 | CPU_FTRS_POWER5 | CPU_FTRS_POWER6 | \ + CPU_FTRS_CELL | CPU_FTR_CI_LARGE_PAGE) #else enum { CPU_FTRS_POSSIBLE = @@ -376,8 +382,8 @@ enum { #ifdef __powerpc64__ #define CPU_FTRS_ALWAYS \ (CPU_FTRS_POWER3 & CPU_FTRS_RS64 & CPU_FTRS_POWER4 & \ - CPU_FTRS_PPC970 & CPU_FTRS_POWER5 & CPU_FTRS_CELL & \ - CPU_FTRS_POSSIBLE) + CPU_FTRS_PPC970 & CPU_FTRS_POWER5 & CPU_FTRS_POWER6 & \ + CPU_FTRS_CELL & CPU_FTRS_POSSIBLE) #else enum { CPU_FTRS_ALWAYS = diff --git a/include/asm-powerpc/io.h b/include/asm-powerpc/io.h index 68efbea379c..f1c2469b884 100644 --- a/include/asm-powerpc/io.h +++ b/include/asm-powerpc/io.h @@ -9,6 +9,9 @@ * 2 of the License, or (at your option) any later version. */ +/* Check of existence of legacy devices */ +extern int check_legacy_ioport(unsigned long base_port); + #ifndef CONFIG_PPC64 #include <asm-ppc/io.h> #else @@ -437,9 +440,6 @@ out: #define dma_cache_wback(_start,_size) do { } while (0) #define dma_cache_wback_inv(_start,_size) do { } while (0) -/* Check of existence of legacy devices */ -extern int check_legacy_ioport(unsigned long base_port); - /* * Convert a physical pointer to a virtual kernel pointer for /dev/mem diff --git a/include/asm-powerpc/page_64.h b/include/asm-powerpc/page_64.h index 3fb061bab9e..eab779c2199 100644 --- a/include/asm-powerpc/page_64.h +++ b/include/asm-powerpc/page_64.h @@ -101,6 +101,7 @@ extern unsigned int HPAGE_SHIFT; - (1U << GET_HTLB_AREA(addr))) & 0xffff) #define ARCH_HAS_HUGEPAGE_ONLY_RANGE +#define ARCH_HAS_HUGETLB_FREE_PGD_RANGE #define ARCH_HAS_PREPARE_HUGEPAGE_RANGE #define ARCH_HAS_SETCLEAR_HUGE_PTE diff --git a/include/asm-powerpc/pgalloc.h b/include/asm-powerpc/pgalloc.h index a00ee002cd1..9f0917c6865 100644 --- a/include/asm-powerpc/pgalloc.h +++ b/include/asm-powerpc/pgalloc.h @@ -17,11 +17,13 @@ extern kmem_cache_t *pgtable_cache[]; #define PTE_CACHE_NUM 0 #define PMD_CACHE_NUM 1 #define PGD_CACHE_NUM 2 +#define HUGEPTE_CACHE_NUM 3 #else #define PTE_CACHE_NUM 0 #define PMD_CACHE_NUM 1 #define PUD_CACHE_NUM 1 #define PGD_CACHE_NUM 0 +#define HUGEPTE_CACHE_NUM 2 #endif /* diff --git a/include/asm-powerpc/spu.h b/include/asm-powerpc/spu.h index f431d8b0b65..7cfcff3ef02 100644 --- a/include/asm-powerpc/spu.h +++ b/include/asm-powerpc/spu.h @@ -117,6 +117,7 @@ struct spu { struct list_head list; struct list_head sched_list; int number; + int nid; u32 isrc; u32 node; u64 flags; diff --git a/include/asm-powerpc/topology.h b/include/asm-powerpc/topology.h index 1e19cd00af2..87362a05542 100644 --- a/include/asm-powerpc/topology.h +++ b/include/asm-powerpc/topology.h @@ -4,6 +4,9 @@ #include <linux/config.h> +struct sys_device; +struct device_node; + #ifdef CONFIG_NUMA #include <asm/mmzone.h> @@ -27,6 +30,8 @@ static inline int node_to_first_cpu(int node) return first_cpu(tmp); } +int of_node_to_nid(struct device_node *device); + #define pcibus_to_node(node) (-1) #define pcibus_to_cpumask(bus) (cpu_online_map) @@ -57,10 +62,29 @@ static inline int node_to_first_cpu(int node) extern void __init dump_numa_cpu_topology(void); +extern int sysfs_add_device_to_node(struct sys_device *dev, int nid); +extern void sysfs_remove_device_from_node(struct sys_device *dev, int nid); + #else +static inline int of_node_to_nid(struct device_node *device) +{ + return 0; +} + static inline void dump_numa_cpu_topology(void) {} +static inline int sysfs_add_device_to_node(struct sys_device *dev, int nid) +{ + return 0; +} + +static inline void sysfs_remove_device_from_node(struct sys_device *dev, + int nid) +{ +} + + #include <asm-generic/topology.h> #endif /* CONFIG_NUMA */ diff --git a/include/asm-powerpc/uaccess.h b/include/asm-powerpc/uaccess.h index 3872e924cdd..d83fc29c2bb 100644 --- a/include/asm-powerpc/uaccess.h +++ b/include/asm-powerpc/uaccess.h @@ -7,6 +7,7 @@ #include <linux/sched.h> #include <linux/errno.h> #include <asm/processor.h> +#include <asm/page.h> #define VERIFY_READ 0 #define VERIFY_WRITE 1 @@ -179,9 +180,11 @@ do { \ #define __put_user_nocheck(x, ptr, size) \ ({ \ long __pu_err; \ - might_sleep(); \ + __typeof__(*(ptr)) __user *__pu_addr = (ptr); \ + if (!is_kernel_addr((unsigned long)__pu_addr)) \ + might_sleep(); \ __chk_user_ptr(ptr); \ - __put_user_size((x), (ptr), (size), __pu_err); \ + __put_user_size((x), __pu_addr, (size), __pu_err); \ __pu_err; \ }) @@ -258,9 +261,11 @@ do { \ ({ \ long __gu_err; \ unsigned long __gu_val; \ + const __typeof__(*(ptr)) __user *__gu_addr = (ptr); \ __chk_user_ptr(ptr); \ - might_sleep(); \ - __get_user_size(__gu_val, (ptr), (size), __gu_err); \ + if (!is_kernel_addr((unsigned long)__gu_addr)) \ + might_sleep(); \ + __get_user_size(__gu_val, __gu_addr, (size), __gu_err); \ (x) = (__typeof__(*(ptr)))__gu_val; \ __gu_err; \ }) @@ -270,9 +275,11 @@ do { \ ({ \ long __gu_err; \ long long __gu_val; \ + const __typeof__(*(ptr)) __user *__gu_addr = (ptr); \ __chk_user_ptr(ptr); \ - might_sleep(); \ - __get_user_size(__gu_val, (ptr), (size), __gu_err); \ + if (!is_kernel_addr((unsigned long)__gu_addr)) \ + might_sleep(); \ + __get_user_size(__gu_val, __gu_addr, (size), __gu_err); \ (x) = (__typeof__(*(ptr)))__gu_val; \ __gu_err; \ }) diff --git a/include/asm-powerpc/unistd.h b/include/asm-powerpc/unistd.h index 34325e29259..908acb44cb8 100644 --- a/include/asm-powerpc/unistd.h +++ b/include/asm-powerpc/unistd.h @@ -304,8 +304,25 @@ #define __NR_splice 283 #define __NR_tee 284 #define __NR_vmsplice 285 +#define __NR_openat 286 +#define __NR_mkdirat 287 +#define __NR_mknodat 288 +#define __NR_fchownat 289 +#define __NR_futimesat 290 +#ifdef __powerpc64__ +#define __NR_newfstatat 291 +#else +#define __NR_fstatat64 291 +#endif +#define __NR_unlinkat 292 +#define __NR_renameat 293 +#define __NR_linkat 294 +#define __NR_symlinkat 295 +#define __NR_readlinkat 296 +#define __NR_fchmodat 297 +#define __NR_faccessat 298 -#define __NR_syscalls 286 +#define __NR_syscalls 299 #ifdef __KERNEL__ #define __NR__exit __NR_exit @@ -458,6 +475,7 @@ type name(type1 arg1, type2 arg2, type3 arg3, type4 arg4, type5 arg5, type6 arg6 #ifdef CONFIG_PPC64 #define __ARCH_WANT_COMPAT_SYS_TIME #define __ARCH_WANT_COMPAT_SYS_RT_SIGSUSPEND +#define __ARCH_WANT_SYS_NEWFSTATAT #endif /* diff --git a/include/asm-ppc/commproc.h b/include/asm-ppc/commproc.h index 973e6090823..31f362966a5 100644 --- a/include/asm-ppc/commproc.h +++ b/include/asm-ppc/commproc.h @@ -35,6 +35,7 @@ #define CPM_CR_INIT_TX ((ushort)0x0002) #define CPM_CR_HUNT_MODE ((ushort)0x0003) #define CPM_CR_STOP_TX ((ushort)0x0004) +#define CPM_CR_GRA_STOP_TX ((ushort)0x0005) #define CPM_CR_RESTART_TX ((ushort)0x0006) #define CPM_CR_CLOSE_RX_BD ((ushort)0x0007) #define CPM_CR_SET_GADDR ((ushort)0x0008) diff --git a/include/asm-ppc/cpm2.h b/include/asm-ppc/cpm2.h index b638b87cebe..c70344b9104 100644 --- a/include/asm-ppc/cpm2.h +++ b/include/asm-ppc/cpm2.h @@ -69,7 +69,7 @@ #define CPM_CR_INIT_TX ((ushort)0x0002) #define CPM_CR_HUNT_MODE ((ushort)0x0003) #define CPM_CR_STOP_TX ((ushort)0x0004) -#define CPM_CR_GRA_STOP_TX ((ushort)0x0005) +#define CPM_CR_GRA_STOP_TX ((ushort)0x0005) #define CPM_CR_RESTART_TX ((ushort)0x0006) #define CPM_CR_SET_GADDR ((ushort)0x0008) #define CPM_CR_START_IDMA ((ushort)0x0009) diff --git a/include/asm-ppc/page.h b/include/asm-ppc/page.h index a70ba2ee552..0fb68a0b018 100644 --- a/include/asm-ppc/page.h +++ b/include/asm-ppc/page.h @@ -20,6 +20,7 @@ /* This must match what is in arch/ppc/Makefile */ #define PAGE_OFFSET CONFIG_KERNEL_START #define KERNELBASE PAGE_OFFSET +#define is_kernel_addr(x) ((x) >= PAGE_OFFSET) #ifndef __ASSEMBLY__ diff --git a/include/asm-ppc/ppc_sys.h b/include/asm-ppc/ppc_sys.h index 4b94f7059eb..40f197af650 100644 --- a/include/asm-ppc/ppc_sys.h +++ b/include/asm-ppc/ppc_sys.h @@ -39,6 +39,8 @@ #error "need definition of ppc_sys_devices" #endif +#define PPC_SYS_IORESOURCE_FIXUPPED 0x00000001 + struct ppc_sys_spec { /* PPC sys is matched via (ID & mask) == value, id could be * PVR, SVR, IMMR, * etc. */ diff --git a/include/asm-ppc/reg_booke.h b/include/asm-ppc/reg_booke.h index 00ad9c754c7..4944c0fb8be 100644 --- a/include/asm-ppc/reg_booke.h +++ b/include/asm-ppc/reg_booke.h @@ -237,6 +237,7 @@ do { \ #endif /* Bit definitions for CCR1. */ +#define CCR1_DPC 0x00000100 /* Disable L1 I-Cache/D-Cache parity checking */ #define CCR1_TCS 0x00000080 /* Timer Clock Select */ /* Bit definitions for the MCSR. */ diff --git a/include/asm-s390/cache.h b/include/asm-s390/cache.h index e20cdd9074d..cdf431b061b 100644 --- a/include/asm-s390/cache.h +++ b/include/asm-s390/cache.h @@ -16,4 +16,6 @@ #define ARCH_KMALLOC_MINALIGN 8 +#define __read_mostly __attribute__((__section__(".data.read_mostly"))) + #endif diff --git a/include/asm-s390/futex.h b/include/asm-s390/futex.h index 6a332a9f099..40c25e166a9 100644 --- a/include/asm-s390/futex.h +++ b/include/asm-s390/futex.h @@ -1,6 +1,121 @@ -#ifndef _ASM_FUTEX_H -#define _ASM_FUTEX_H +#ifndef _ASM_S390_FUTEX_H +#define _ASM_S390_FUTEX_H -#include <asm-generic/futex.h> +#ifdef __KERNEL__ -#endif +#include <linux/futex.h> +#include <asm/errno.h> +#include <asm/uaccess.h> + +#ifndef __s390x__ +#define __futex_atomic_fixup \ + ".section __ex_table,\"a\"\n" \ + " .align 4\n" \ + " .long 0b,2b,1b,2b\n" \ + ".previous" +#else /* __s390x__ */ +#define __futex_atomic_fixup \ + ".section __ex_table,\"a\"\n" \ + " .align 8\n" \ + " .quad 0b,2b,1b,2b\n" \ + ".previous" +#endif /* __s390x__ */ + +#define __futex_atomic_op(insn, ret, oldval, newval, uaddr, oparg) \ + asm volatile(" l %1,0(%6)\n" \ + "0: " insn \ + " cs %1,%2,0(%6)\n" \ + "1: jl 0b\n" \ + " lhi %0,0\n" \ + "2:\n" \ + __futex_atomic_fixup \ + : "=d" (ret), "=&d" (oldval), "=&d" (newval), \ + "=m" (*uaddr) \ + : "0" (-EFAULT), "d" (oparg), "a" (uaddr), \ + "m" (*uaddr) : "cc" ); + +static inline int futex_atomic_op_inuser (int encoded_op, int __user *uaddr) +{ + int op = (encoded_op >> 28) & 7; + int cmp = (encoded_op >> 24) & 15; + int oparg = (encoded_op << 8) >> 20; + int cmparg = (encoded_op << 20) >> 20; + int oldval = 0, newval, ret; + if (encoded_op & (FUTEX_OP_OPARG_SHIFT << 28)) + oparg = 1 << oparg; + + if (! access_ok (VERIFY_WRITE, uaddr, sizeof(int))) + return -EFAULT; + + inc_preempt_count(); + + switch (op) { + case FUTEX_OP_SET: + __futex_atomic_op("lr %2,%5\n", + ret, oldval, newval, uaddr, oparg); + break; + case FUTEX_OP_ADD: + __futex_atomic_op("lr %2,%1\nar %2,%5\n", + ret, oldval, newval, uaddr, oparg); + break; + case FUTEX_OP_OR: + __futex_atomic_op("lr %2,%1\nor %2,%5\n", + ret, oldval, newval, uaddr, oparg); + break; + case FUTEX_OP_ANDN: + __futex_atomic_op("lr %2,%1\nnr %2,%5\n", + ret, oldval, newval, uaddr, oparg); + break; + case FUTEX_OP_XOR: + __futex_atomic_op("lr %2,%1\nxr %2,%5\n", + ret, oldval, newval, uaddr, oparg); + break; + default: + ret = -ENOSYS; + } + + dec_preempt_count(); + + if (!ret) { + switch (cmp) { + case FUTEX_OP_CMP_EQ: ret = (oldval == cmparg); break; + case FUTEX_OP_CMP_NE: ret = (oldval != cmparg); break; + case FUTEX_OP_CMP_LT: ret = (oldval < cmparg); break; + case FUTEX_OP_CMP_GE: ret = (oldval >= cmparg); break; + case FUTEX_OP_CMP_LE: ret = (oldval <= cmparg); break; + case FUTEX_OP_CMP_GT: ret = (oldval > cmparg); break; + default: ret = -ENOSYS; + } + } + return ret; +} + +static inline int +futex_atomic_cmpxchg_inatomic(int __user *uaddr, int oldval, int newval) +{ + int ret; + + if (! access_ok (VERIFY_WRITE, uaddr, sizeof(int))) + return -EFAULT; + asm volatile(" cs %1,%4,0(%5)\n" + "0: lr %0,%1\n" + "1:\n" +#ifndef __s390x__ + ".section __ex_table,\"a\"\n" + " .align 4\n" + " .long 0b,1b\n" + ".previous" +#else /* __s390x__ */ + ".section __ex_table,\"a\"\n" + " .align 8\n" + " .quad 0b,1b\n" + ".previous" +#endif /* __s390x__ */ + : "=d" (ret), "+d" (oldval), "=m" (*uaddr) + : "0" (-EFAULT), "d" (newval), "a" (uaddr), "m" (*uaddr) + : "cc", "memory" ); + return oldval; +} + +#endif /* __KERNEL__ */ +#endif /* _ASM_S390_FUTEX_H */ diff --git a/include/asm-sparc/unistd.h b/include/asm-sparc/unistd.h index 32a48f623e2..f5611a721fb 100644 --- a/include/asm-sparc/unistd.h +++ b/include/asm-sparc/unistd.h @@ -41,7 +41,7 @@ #define __NR_capset 22 /* Linux Specific */ #define __NR_setuid 23 /* Implemented via setreuid in SunOS */ #define __NR_getuid 24 /* Common */ -/* #define __NR_time alias 25 ENOSYS under SunOS */ +#define __NR_vmsplice 25 /* ENOSYS under SunOS */ #define __NR_ptrace 26 /* Common */ #define __NR_alarm 27 /* Implemented via setitimer in SunOS */ #define __NR_sigaltstack 28 /* Common */ diff --git a/include/asm-sparc64/tlbflush.h b/include/asm-sparc64/tlbflush.h index 9ad5d9c51d4..e3a7c453b50 100644 --- a/include/asm-sparc64/tlbflush.h +++ b/include/asm-sparc64/tlbflush.h @@ -22,8 +22,6 @@ extern void flush_tlb_pending(void); /* Local cpu only. */ extern void __flush_tlb_all(void); -extern void __flush_tlb_page(unsigned long context, unsigned long page, unsigned long r); - extern void __flush_tlb_kernel_range(unsigned long start, unsigned long end); #ifndef CONFIG_SMP diff --git a/include/asm-sparc64/unistd.h b/include/asm-sparc64/unistd.h index ca80e8aca12..68705748bec 100644 --- a/include/asm-sparc64/unistd.h +++ b/include/asm-sparc64/unistd.h @@ -41,7 +41,7 @@ #define __NR_capset 22 /* Linux Specific */ #define __NR_setuid 23 /* Implemented via setreuid in SunOS */ #define __NR_getuid 24 /* Common */ -/* #define __NR_time alias 25 ENOSYS under SunOS */ +#define __NR_vmsplice 25 /* ENOSYS under SunOS */ #define __NR_ptrace 26 /* Common */ #define __NR_alarm 27 /* Implemented via setitimer in SunOS */ #define __NR_sigaltstack 28 /* Common */ diff --git a/include/asm-x86_64/e820.h b/include/asm-x86_64/e820.h index 93b51df5168..670a3388e70 100644 --- a/include/asm-x86_64/e820.h +++ b/include/asm-x86_64/e820.h @@ -59,6 +59,8 @@ extern void __init parse_memopt(char *p, char **end); extern void __init parse_memmapopt(char *p, char **end); extern struct e820map e820; + +extern unsigned ebda_addr, ebda_size; #endif/*!__ASSEMBLY__*/ #endif/*__E820_HEADER*/ diff --git a/include/asm-x86_64/io_apic.h b/include/asm-x86_64/io_apic.h index ee1bc69aec9..52484e82c64 100644 --- a/include/asm-x86_64/io_apic.h +++ b/include/asm-x86_64/io_apic.h @@ -205,6 +205,7 @@ extern int skip_ioapic_setup; extern int io_apic_get_version (int ioapic); extern int io_apic_get_redir_entries (int ioapic); extern int io_apic_set_pci_routing (int ioapic, int pin, int irq, int, int); +extern int timer_uses_ioapic_pin_0; #endif extern int sis_apic_bug; /* dummy */ diff --git a/include/asm-xtensa/signal.h b/include/asm-xtensa/signal.h index 5d6fc9cdf58..a99c9aec64e 100644 --- a/include/asm-xtensa/signal.h +++ b/include/asm-xtensa/signal.h @@ -118,9 +118,9 @@ typedef struct { * SA_INTERRUPT is also used by the irq handling routines. * SA_SHIRQ is for shared interrupt support on PCI and EISA. */ -#define SA_PROBE SA_ONESHOT #define SA_SAMPLE_RANDOM SA_RESTART #define SA_SHIRQ 0x04000000 +#define SA_PROBEIRQ 0x08000000 #endif #define SIG_BLOCK 0 /* for blocking signals */ diff --git a/include/linux/audit.h b/include/linux/audit.h index 1c47c59058c..b74c148f14e 100644 --- a/include/linux/audit.h +++ b/include/linux/audit.h @@ -83,6 +83,7 @@ #define AUDIT_CONFIG_CHANGE 1305 /* Audit system configuration change */ #define AUDIT_SOCKADDR 1306 /* sockaddr copied as syscall arg */ #define AUDIT_CWD 1307 /* Current working directory */ +#define AUDIT_IPC_SET_PERM 1311 /* IPC new permissions record type */ #define AUDIT_AVC 1400 /* SE Linux avc denial or grant */ #define AUDIT_SELINUX_ERR 1401 /* Internal SE Linux Errors */ @@ -145,6 +146,11 @@ #define AUDIT_PERS 10 #define AUDIT_ARCH 11 #define AUDIT_MSGTYPE 12 +#define AUDIT_SE_USER 13 /* security label user */ +#define AUDIT_SE_ROLE 14 /* security label role */ +#define AUDIT_SE_TYPE 15 /* security label type */ +#define AUDIT_SE_SEN 16 /* security label sensitivity label */ +#define AUDIT_SE_CLR 17 /* security label clearance label */ /* These are ONLY useful when checking * at syscall exit time (AUDIT_AT_EXIT). */ @@ -287,10 +293,10 @@ struct netlink_skb_parms; /* Public API */ extern int audit_alloc(struct task_struct *task); extern void audit_free(struct task_struct *task); -extern void audit_syscall_entry(struct task_struct *task, int arch, +extern void audit_syscall_entry(int arch, int major, unsigned long a0, unsigned long a1, unsigned long a2, unsigned long a3); -extern void audit_syscall_exit(struct task_struct *task, int failed, long return_code); +extern void audit_syscall_exit(int failed, long return_code); extern void audit_getname(const char *name); extern void audit_putname(const char *name); extern void __audit_inode(const char *name, const struct inode *inode, unsigned flags); @@ -314,7 +320,8 @@ extern void auditsc_get_stamp(struct audit_context *ctx, struct timespec *t, unsigned int *serial); extern int audit_set_loginuid(struct task_struct *task, uid_t loginuid); extern uid_t audit_get_loginuid(struct audit_context *ctx); -extern int audit_ipc_perms(unsigned long qbytes, uid_t uid, gid_t gid, mode_t mode, struct kern_ipc_perm *ipcp); +extern int audit_ipc_obj(struct kern_ipc_perm *ipcp); +extern int audit_ipc_set_perm(unsigned long qbytes, uid_t uid, gid_t gid, mode_t mode, struct kern_ipc_perm *ipcp); extern int audit_socketcall(int nargs, unsigned long *args); extern int audit_sockaddr(int len, void *addr); extern int audit_avc_path(struct dentry *dentry, struct vfsmount *mnt); @@ -323,8 +330,8 @@ extern int audit_set_macxattr(const char *name); #else #define audit_alloc(t) ({ 0; }) #define audit_free(t) do { ; } while (0) -#define audit_syscall_entry(t,ta,a,b,c,d,e) do { ; } while (0) -#define audit_syscall_exit(t,f,r) do { ; } while (0) +#define audit_syscall_entry(ta,a,b,c,d,e) do { ; } while (0) +#define audit_syscall_exit(f,r) do { ; } while (0) #define audit_getname(n) do { ; } while (0) #define audit_putname(n) do { ; } while (0) #define __audit_inode(n,i,f) do { ; } while (0) @@ -333,7 +340,8 @@ extern int audit_set_macxattr(const char *name); #define audit_inode_child(d,i,p) do { ; } while (0) #define auditsc_get_stamp(c,t,s) do { BUG(); } while (0) #define audit_get_loginuid(c) ({ -1; }) -#define audit_ipc_perms(q,u,g,m,i) ({ 0; }) +#define audit_ipc_obj(i) ({ 0; }) +#define audit_ipc_set_perm(q,u,g,m,i) ({ 0; }) #define audit_socketcall(n,a) ({ 0; }) #define audit_sockaddr(len, addr) ({ 0; }) #define audit_avc_path(dentry, mnt) ({ 0; }) @@ -366,7 +374,7 @@ extern void audit_log_d_path(struct audit_buffer *ab, extern int audit_filter_user(struct netlink_skb_parms *cb, int type); extern int audit_filter_type(int type); extern int audit_receive_filter(int type, int pid, int uid, int seq, - void *data, size_t datasz, uid_t loginuid); + void *data, size_t datasz, uid_t loginuid, u32 sid); #else #define audit_log(c,g,t,f,...) do { ; } while (0) #define audit_log_start(c,g,t) ({ NULL; }) diff --git a/include/linux/debugfs.h b/include/linux/debugfs.h index 176e2d37157..047567d34ca 100644 --- a/include/linux/debugfs.h +++ b/include/linux/debugfs.h @@ -58,9 +58,8 @@ struct dentry *debugfs_create_blob(const char *name, mode_t mode, */ static inline struct dentry *debugfs_create_file(const char *name, mode_t mode, - struct dentry *parent, - void *data, - struct file_operations *fops) + struct dentry *parent, void *data, + const struct file_operations *fops) { return ERR_PTR(-ENODEV); } diff --git a/include/linux/device.h b/include/linux/device.h index f6e72a65a3f..e8e53b9accc 100644 --- a/include/linux/device.h +++ b/include/linux/device.h @@ -200,6 +200,7 @@ extern int class_device_create_file(struct class_device *, * @node: for internal use by the driver core only. * @kobj: for internal use by the driver core only. * @devt_attr: for internal use by the driver core only. + * @groups: optional additional groups to be created * @dev: if set, a symlink to the struct device is created in the sysfs * directory for this struct class device. * @class_data: pointer to whatever you want to store here for this struct @@ -228,6 +229,7 @@ struct class_device { struct device * dev; /* not necessary, but nice to have */ void * class_data; /* class-specific data */ struct class_device *parent; /* parent of this child device, if there is one */ + struct attribute_group ** groups; /* optional groups */ void (*release)(struct class_device *dev); int (*uevent)(struct class_device *dev, char **envp, diff --git a/include/linux/dma-mapping.h b/include/linux/dma-mapping.h index ff61817082f..635690cf3e3 100644 --- a/include/linux/dma-mapping.h +++ b/include/linux/dma-mapping.h @@ -14,6 +14,7 @@ enum dma_data_direction { }; #define DMA_64BIT_MASK 0xffffffffffffffffULL +#define DMA_48BIT_MASK 0x0000ffffffffffffULL #define DMA_40BIT_MASK 0x000000ffffffffffULL #define DMA_39BIT_MASK 0x0000007fffffffffULL #define DMA_32BIT_MASK 0x00000000ffffffffULL diff --git a/include/linux/fs_uart_pd.h b/include/linux/fs_uart_pd.h new file mode 100644 index 00000000000..f5975126b71 --- /dev/null +++ b/include/linux/fs_uart_pd.h @@ -0,0 +1,60 @@ +/* + * Platform information definitions for the CPM Uart driver. + * + * 2006 (c) MontaVista Software, Inc. + * Vitaly Bordug <vbordug@ru.mvista.com> + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#ifndef FS_UART_PD_H +#define FS_UART_PD_H + +#include <linux/version.h> +#include <asm/types.h> + +enum fs_uart_id { + fsid_smc1_uart, + fsid_smc2_uart, + fsid_scc1_uart, + fsid_scc2_uart, + fsid_scc3_uart, + fsid_scc4_uart, + fs_uart_nr, +}; + +static inline int fs_uart_id_scc2fsid(int id) +{ + return fsid_scc1_uart + id - 1; +} + +static inline int fs_uart_id_fsid2scc(int id) +{ + return id - fsid_scc1_uart + 1; +} + +static inline int fs_uart_id_smc2fsid(int id) +{ + return fsid_smc1_uart + id - 1; +} + +static inline int fs_uart_id_fsid2smc(int id) +{ + return id - fsid_smc1_uart + 1; +} + +struct fs_uart_platform_info { + void(*init_ioports)(void); + /* device specific information */ + int fs_no; /* controller index */ + u32 uart_clk; + u8 tx_num_fifo; + u8 tx_buf_size; + u8 rx_num_fifo; + u8 rx_buf_size; + u8 brg; +}; + +#endif diff --git a/include/linux/input.h b/include/linux/input.h index b0e612dda0c..50e338d2ffd 100644 --- a/include/linux/input.h +++ b/include/linux/input.h @@ -12,8 +12,6 @@ #ifdef __KERNEL__ #include <linux/time.h> #include <linux/list.h> -#include <linux/device.h> -#include <linux/mod_devicetable.h> #else #include <sys/time.h> #include <sys/ioctl.h> @@ -58,6 +56,8 @@ struct input_absinfo { #define EVIOCGVERSION _IOR('E', 0x01, int) /* get driver version */ #define EVIOCGID _IOR('E', 0x02, struct input_id) /* get device ID */ +#define EVIOCGREP _IOR('E', 0x03, int[2]) /* get repeat settings */ +#define EVIOCSREP _IOW('E', 0x03, int[2]) /* set repeat settings */ #define EVIOCGKEYCODE _IOR('E', 0x04, int[2]) /* get keycode */ #define EVIOCSKEYCODE _IOW('E', 0x04, int[2]) /* set keycode */ @@ -577,15 +577,15 @@ struct input_absinfo { * Switch events */ -#define SW_0 0x00 -#define SW_1 0x01 -#define SW_2 0x02 -#define SW_3 0x03 -#define SW_4 0x04 -#define SW_5 0x05 -#define SW_6 0x06 -#define SW_7 0x07 -#define SW_MAX 0x0f +#define SW_0 0x00 +#define SW_1 0x01 +#define SW_2 0x02 +#define SW_3 0x03 +#define SW_4 0x04 +#define SW_5 0x05 +#define SW_6 0x06 +#define SW_7 0x07 +#define SW_MAX 0x0f /* * Misc events @@ -805,52 +805,16 @@ struct ff_effect { #define FF_MAX 0x7f -struct input_device_id { - - kernel_ulong_t flags; - - struct input_id id; - - kernel_ulong_t evbit[EV_MAX/BITS_PER_LONG+1]; - kernel_ulong_t keybit[KEY_MAX/BITS_PER_LONG+1]; - kernel_ulong_t relbit[REL_MAX/BITS_PER_LONG+1]; - kernel_ulong_t absbit[ABS_MAX/BITS_PER_LONG+1]; - kernel_ulong_t mscbit[MSC_MAX/BITS_PER_LONG+1]; - kernel_ulong_t ledbit[LED_MAX/BITS_PER_LONG+1]; - kernel_ulong_t sndbit[SND_MAX/BITS_PER_LONG+1]; - kernel_ulong_t ffbit[FF_MAX/BITS_PER_LONG+1]; - kernel_ulong_t swbit[SW_MAX/BITS_PER_LONG+1]; - - kernel_ulong_t driver_info; -}; - -/* - * Structure for hotplug & device<->driver matching. - */ - -#define INPUT_DEVICE_ID_MATCH_BUS 1 -#define INPUT_DEVICE_ID_MATCH_VENDOR 2 -#define INPUT_DEVICE_ID_MATCH_PRODUCT 4 -#define INPUT_DEVICE_ID_MATCH_VERSION 8 - -#define INPUT_DEVICE_ID_MATCH_EVBIT 0x010 -#define INPUT_DEVICE_ID_MATCH_KEYBIT 0x020 -#define INPUT_DEVICE_ID_MATCH_RELBIT 0x040 -#define INPUT_DEVICE_ID_MATCH_ABSBIT 0x080 -#define INPUT_DEVICE_ID_MATCH_MSCIT 0x100 -#define INPUT_DEVICE_ID_MATCH_LEDBIT 0x200 -#define INPUT_DEVICE_ID_MATCH_SNDBIT 0x400 -#define INPUT_DEVICE_ID_MATCH_FFBIT 0x800 -#define INPUT_DEVICE_ID_MATCH_SWBIT 0x1000 - #ifdef __KERNEL__ /* * In-kernel definitions. */ +#include <linux/device.h> #include <linux/fs.h> #include <linux/timer.h> +#include <linux/mod_devicetable.h> #define NBITS(x) (((x)/BITS_PER_LONG)+1) #define BIT(x) (1UL<<((x)%BITS_PER_LONG)) @@ -951,9 +915,49 @@ struct input_dev { }; #define to_input_dev(d) container_of(d, struct input_dev, cdev) -#define INPUT_DEVICE_ID_MATCH_DEVICE\ +/* + * Verify that we are in sync with input_device_id mod_devicetable.h #defines + */ + +#if EV_MAX != INPUT_DEVICE_ID_EV_MAX +#error "EV_MAX and INPUT_DEVICE_ID_EV_MAX do not match" +#endif + +#if KEY_MAX != INPUT_DEVICE_ID_KEY_MAX +#error "KEY_MAX and INPUT_DEVICE_ID_KEY_MAX do not match" +#endif + +#if REL_MAX != INPUT_DEVICE_ID_REL_MAX +#error "REL_MAX and INPUT_DEVICE_ID_REL_MAX do not match" +#endif + +#if ABS_MAX != INPUT_DEVICE_ID_ABS_MAX +#error "ABS_MAX and INPUT_DEVICE_ID_ABS_MAX do not match" +#endif + +#if MSC_MAX != INPUT_DEVICE_ID_MSC_MAX +#error "MSC_MAX and INPUT_DEVICE_ID_MSC_MAX do not match" +#endif + +#if LED_MAX != INPUT_DEVICE_ID_LED_MAX +#error "LED_MAX and INPUT_DEVICE_ID_LED_MAX do not match" +#endif + +#if SND_MAX != INPUT_DEVICE_ID_SND_MAX +#error "SND_MAX and INPUT_DEVICE_ID_SND_MAX do not match" +#endif + +#if FF_MAX != INPUT_DEVICE_ID_FF_MAX +#error "FF_MAX and INPUT_DEVICE_ID_FF_MAX do not match" +#endif + +#if SW_MAX != INPUT_DEVICE_ID_SW_MAX +#error "SW_MAX and INPUT_DEVICE_ID_SW_MAX do not match" +#endif + +#define INPUT_DEVICE_ID_MATCH_DEVICE \ (INPUT_DEVICE_ID_MATCH_BUS | INPUT_DEVICE_ID_MATCH_VENDOR | INPUT_DEVICE_ID_MATCH_PRODUCT) -#define INPUT_DEVICE_ID_MATCH_DEVICE_AND_VERSION\ +#define INPUT_DEVICE_ID_MATCH_DEVICE_AND_VERSION \ (INPUT_DEVICE_ID_MATCH_DEVICE | INPUT_DEVICE_ID_MATCH_VERSION) struct input_handle; @@ -1016,7 +1020,8 @@ static inline void input_put_device(struct input_dev *dev) static inline void input_free_device(struct input_dev *dev) { - input_put_device(dev); + if (dev) + input_put_device(dev); } int input_register_device(struct input_dev *); diff --git a/include/linux/kobject.h b/include/linux/kobject.h index dcd0623be89..c187c53cecd 100644 --- a/include/linux/kobject.h +++ b/include/linux/kobject.h @@ -257,9 +257,8 @@ struct subsys_attribute { }; extern int subsys_create_file(struct subsystem * , struct subsys_attribute *); -extern void subsys_remove_file(struct subsystem * , struct subsys_attribute *); -#if defined(CONFIG_HOTPLUG) && defined(CONFIG_NET) +#if defined(CONFIG_HOTPLUG) void kobject_uevent(struct kobject *kobj, enum kobject_action action); int add_uevent_var(char **envp, int num_envp, int *cur_index, diff --git a/include/linux/list.h b/include/linux/list.h index 67258b47e9c..76f05718342 100644 --- a/include/linux/list.h +++ b/include/linux/list.h @@ -619,7 +619,7 @@ static inline void hlist_del_rcu(struct hlist_node *n) static inline void hlist_del_init(struct hlist_node *n) { - if (n->pprev) { + if (!hlist_unhashed(n)) { __hlist_del(n); INIT_HLIST_NODE(n); } diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h index 30dd978c1ec..991a37382a2 100644 --- a/include/linux/mmc/card.h +++ b/include/linux/mmc/card.h @@ -28,6 +28,7 @@ struct mmc_csd { unsigned short cmdclass; unsigned short tacc_clks; unsigned int tacc_ns; + unsigned int r2w_factor; unsigned int max_dtr; unsigned int read_blkbits; unsigned int write_blkbits; diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h index 7b08c11ec4c..f6977708585 100644 --- a/include/linux/mod_devicetable.h +++ b/include/linux/mod_devicetable.h @@ -249,4 +249,52 @@ struct i2c_device_id { __u16 id; }; +/* Input */ +#define INPUT_DEVICE_ID_EV_MAX 0x1f +#define INPUT_DEVICE_ID_KEY_MAX 0x1ff +#define INPUT_DEVICE_ID_REL_MAX 0x0f +#define INPUT_DEVICE_ID_ABS_MAX 0x3f +#define INPUT_DEVICE_ID_MSC_MAX 0x07 +#define INPUT_DEVICE_ID_LED_MAX 0x0f +#define INPUT_DEVICE_ID_SND_MAX 0x07 +#define INPUT_DEVICE_ID_FF_MAX 0x7f +#define INPUT_DEVICE_ID_SW_MAX 0x0f + +#define INPUT_DEVICE_ID_MATCH_BUS 1 +#define INPUT_DEVICE_ID_MATCH_VENDOR 2 +#define INPUT_DEVICE_ID_MATCH_PRODUCT 4 +#define INPUT_DEVICE_ID_MATCH_VERSION 8 + +#define INPUT_DEVICE_ID_MATCH_EVBIT 0x0010 +#define INPUT_DEVICE_ID_MATCH_KEYBIT 0x0020 +#define INPUT_DEVICE_ID_MATCH_RELBIT 0x0040 +#define INPUT_DEVICE_ID_MATCH_ABSBIT 0x0080 +#define INPUT_DEVICE_ID_MATCH_MSCIT 0x0100 +#define INPUT_DEVICE_ID_MATCH_LEDBIT 0x0200 +#define INPUT_DEVICE_ID_MATCH_SNDBIT 0x0400 +#define INPUT_DEVICE_ID_MATCH_FFBIT 0x0800 +#define INPUT_DEVICE_ID_MATCH_SWBIT 0x1000 + +struct input_device_id { + + kernel_ulong_t flags; + + __u16 bustype; + __u16 vendor; + __u16 product; + __u16 version; + + kernel_ulong_t evbit[INPUT_DEVICE_ID_EV_MAX / BITS_PER_LONG + 1]; + kernel_ulong_t keybit[INPUT_DEVICE_ID_KEY_MAX / BITS_PER_LONG + 1]; + kernel_ulong_t relbit[INPUT_DEVICE_ID_REL_MAX / BITS_PER_LONG + 1]; + kernel_ulong_t absbit[INPUT_DEVICE_ID_ABS_MAX / BITS_PER_LONG + 1]; + kernel_ulong_t mscbit[INPUT_DEVICE_ID_MSC_MAX / BITS_PER_LONG + 1]; + kernel_ulong_t ledbit[INPUT_DEVICE_ID_LED_MAX / BITS_PER_LONG + 1]; + kernel_ulong_t sndbit[INPUT_DEVICE_ID_SND_MAX / BITS_PER_LONG + 1]; + kernel_ulong_t ffbit[INPUT_DEVICE_ID_FF_MAX / BITS_PER_LONG + 1]; + kernel_ulong_t swbit[INPUT_DEVICE_ID_SW_MAX / BITS_PER_LONG + 1]; + + kernel_ulong_t driver_info; +}; + #endif /* LINUX_MOD_DEVICETABLE_H */ diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index 01db7b88a2b..f4169bbb60e 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -433,8 +433,7 @@ struct net_device /* register/unregister state machine */ enum { NETREG_UNINITIALIZED=0, - NETREG_REGISTERING, /* called register_netdevice */ - NETREG_REGISTERED, /* completed register todo */ + NETREG_REGISTERED, /* completed register_netdevice */ NETREG_UNREGISTERING, /* called unregister_netdevice */ NETREG_UNREGISTERED, /* completed unregister todo */ NETREG_RELEASED, /* called free_netdev */ @@ -506,6 +505,8 @@ struct net_device /* class/net/name entry */ struct class_device class_dev; + /* space for optional statistics and wireless sysfs groups */ + struct attribute_group *sysfs_groups[3]; }; #define NETDEV_ALIGN 32 @@ -829,21 +830,19 @@ static inline void netif_rx_schedule(struct net_device *dev) __netif_rx_schedule(dev); } - -static inline void __netif_rx_reschedule(struct net_device *dev, int undo) -{ - dev->quota += undo; - list_add_tail(&dev->poll_list, &__get_cpu_var(softnet_data).poll_list); - __raise_softirq_irqoff(NET_RX_SOFTIRQ); -} - -/* Try to reschedule poll. Called by dev->poll() after netif_rx_complete(). */ +/* Try to reschedule poll. Called by dev->poll() after netif_rx_complete(). + * Do not inline this? + */ static inline int netif_rx_reschedule(struct net_device *dev, int undo) { if (netif_rx_schedule_prep(dev)) { unsigned long flags; + + dev->quota += undo; + local_irq_save(flags); - __netif_rx_reschedule(dev, undo); + list_add_tail(&dev->poll_list, &__get_cpu_var(softnet_data).poll_list); + __raise_softirq_irqoff(NET_RX_SOFTIRQ); local_irq_restore(flags); return 1; } diff --git a/include/linux/netfilter/x_tables.h b/include/linux/netfilter/x_tables.h index 38701454e19..48cc32d83f7 100644 --- a/include/linux/netfilter/x_tables.h +++ b/include/linux/netfilter/x_tables.h @@ -337,6 +337,10 @@ struct compat_xt_entry_match char name[XT_FUNCTION_MAXNAMELEN - 1]; u_int8_t revision; } user; + struct { + u_int16_t match_size; + compat_uptr_t match; + } kernel; u_int16_t match_size; } u; unsigned char data[0]; @@ -350,6 +354,10 @@ struct compat_xt_entry_target char name[XT_FUNCTION_MAXNAMELEN - 1]; u_int8_t revision; } user; + struct { + u_int16_t target_size; + compat_uptr_t target; + } kernel; u_int16_t target_size; } u; unsigned char data[0]; diff --git a/include/linux/netfilter_ipv4/ip_conntrack_helper_h323_asn1.h b/include/linux/netfilter_ipv4/ip_conntrack_helper_h323_asn1.h index 0bd828081c0..c6e9a0b6d30 100644 --- a/include/linux/netfilter_ipv4/ip_conntrack_helper_h323_asn1.h +++ b/include/linux/netfilter_ipv4/ip_conntrack_helper_h323_asn1.h @@ -2,7 +2,7 @@ * ip_conntrack_helper_h323_asn1.h - BER and PER decoding library for H.323 * conntrack/NAT module. * - * Copyright (c) 2006 by Jing Min Zhao <zhaojingmin@hotmail.com> + * Copyright (c) 2006 by Jing Min Zhao <zhaojingmin@users.sourceforge.net> * * This source code is licensed under General Public License version 2. * diff --git a/include/linux/netlink.h b/include/linux/netlink.h index f8f3d1c927f..87b8a5703eb 100644 --- a/include/linux/netlink.h +++ b/include/linux/netlink.h @@ -143,6 +143,7 @@ struct netlink_skb_parms __u32 dst_group; kernel_cap_t eff_cap; __u32 loginuid; /* Login (audit) uid */ + __u32 sid; /* SELinux security id */ }; #define NETLINK_CB(skb) (*(struct netlink_skb_parms*)&((skb)->cb)) diff --git a/include/linux/pagemap.h b/include/linux/pagemap.h index 9539efd4f7e..7a1af574ded 100644 --- a/include/linux/pagemap.h +++ b/include/linux/pagemap.h @@ -78,6 +78,8 @@ extern struct page * find_or_create_page(struct address_space *mapping, unsigned long index, gfp_t gfp_mask); unsigned find_get_pages(struct address_space *mapping, pgoff_t start, unsigned int nr_pages, struct page **pages); +unsigned find_get_pages_contig(struct address_space *mapping, pgoff_t start, + unsigned int nr_pages, struct page **pages); unsigned find_get_pages_tag(struct address_space *mapping, pgoff_t *index, int tag, unsigned int nr_pages, struct page **pages); diff --git a/include/linux/pipe_fs_i.h b/include/linux/pipe_fs_i.h index 0008d4bd405..ea4f7cd7bfd 100644 --- a/include/linux/pipe_fs_i.h +++ b/include/linux/pipe_fs_i.h @@ -5,8 +5,9 @@ #define PIPE_BUFFERS (16) -#define PIPE_BUF_FLAG_STOLEN 0x01 -#define PIPE_BUF_FLAG_LRU 0x02 +#define PIPE_BUF_FLAG_LRU 0x01 /* page is on the LRU */ +#define PIPE_BUF_FLAG_ATOMIC 0x02 /* was atomically mapped */ +#define PIPE_BUF_FLAG_GIFT 0x04 /* page is a gift */ struct pipe_buffer { struct page *page; @@ -15,10 +16,23 @@ struct pipe_buffer { unsigned int flags; }; +/* + * Note on the nesting of these functions: + * + * ->pin() + * ->steal() + * ... + * ->map() + * ... + * ->unmap() + * + * That is, ->map() must be called on a pinned buffer, same goes for ->steal(). + */ struct pipe_buf_operations { int can_merge; - void * (*map)(struct file *, struct pipe_inode_info *, struct pipe_buffer *); - void (*unmap)(struct pipe_inode_info *, struct pipe_buffer *); + void * (*map)(struct pipe_inode_info *, struct pipe_buffer *, int); + void (*unmap)(struct pipe_inode_info *, struct pipe_buffer *, void *); + int (*pin)(struct pipe_inode_info *, struct pipe_buffer *); void (*release)(struct pipe_inode_info *, struct pipe_buffer *); int (*steal)(struct pipe_inode_info *, struct pipe_buffer *); void (*get)(struct pipe_inode_info *, struct pipe_buffer *); @@ -51,6 +65,13 @@ struct pipe_inode_info * alloc_pipe_info(struct inode * inode); void free_pipe_info(struct inode * inode); void __free_pipe_info(struct pipe_inode_info *); +/* Generic pipe buffer ops functions */ +void *generic_pipe_buf_map(struct pipe_inode_info *, struct pipe_buffer *, int); +void generic_pipe_buf_unmap(struct pipe_inode_info *, struct pipe_buffer *, void *); +void generic_pipe_buf_get(struct pipe_inode_info *, struct pipe_buffer *); +int generic_pipe_buf_pin(struct pipe_inode_info *, struct pipe_buffer *); +int generic_pipe_buf_steal(struct pipe_inode_info *, struct pipe_buffer *); + /* * splice is tied to pipes as a transport (at least for now), so we'll just * add the splice flags here. @@ -60,6 +81,7 @@ void __free_pipe_info(struct pipe_inode_info *); /* we may still block on the fd we splice */ /* from/to, of course */ #define SPLICE_F_MORE (0x04) /* expect more data */ +#define SPLICE_F_GIFT (0x08) /* pages passed in are a gift */ /* * Passed to the actors diff --git a/include/linux/security.h b/include/linux/security.h index aaa0a5cdbf7..1bab48f6aea 100644 --- a/include/linux/security.h +++ b/include/linux/security.h @@ -869,11 +869,6 @@ struct swap_info_struct; * @ipcp contains the kernel IPC permission structure * @flag contains the desired (requested) permission set * Return 0 if permission is granted. - * @ipc_getsecurity: - * Copy the security label associated with the ipc object into - * @buffer. @buffer may be NULL to request the size of the buffer - * required. @size indicates the size of @buffer in bytes. Return - * number of bytes used/required on success. * * Security hooks for individual messages held in System V IPC message queues * @msg_msg_alloc_security: @@ -1223,7 +1218,6 @@ struct security_operations { void (*task_to_inode)(struct task_struct *p, struct inode *inode); int (*ipc_permission) (struct kern_ipc_perm * ipcp, short flag); - int (*ipc_getsecurity)(struct kern_ipc_perm *ipcp, void *buffer, size_t size); int (*msg_msg_alloc_security) (struct msg_msg * msg); void (*msg_msg_free_security) (struct msg_msg * msg); @@ -1887,11 +1881,6 @@ static inline int security_ipc_permission (struct kern_ipc_perm *ipcp, return security_ops->ipc_permission (ipcp, flag); } -static inline int security_ipc_getsecurity(struct kern_ipc_perm *ipcp, void *buffer, size_t size) -{ - return security_ops->ipc_getsecurity(ipcp, buffer, size); -} - static inline int security_msg_msg_alloc (struct msg_msg * msg) { return security_ops->msg_msg_alloc_security (msg); @@ -2532,11 +2521,6 @@ static inline int security_ipc_permission (struct kern_ipc_perm *ipcp, return 0; } -static inline int security_ipc_getsecurity(struct kern_ipc_perm *ipcp, void *buffer, size_t size) -{ - return -EOPNOTSUPP; -} - static inline int security_msg_msg_alloc (struct msg_msg * msg) { return 0; diff --git a/include/linux/selinux.h b/include/linux/selinux.h new file mode 100644 index 00000000000..4047bcde448 --- /dev/null +++ b/include/linux/selinux.h @@ -0,0 +1,177 @@ +/* + * SELinux services exported to the rest of the kernel. + * + * Author: James Morris <jmorris@redhat.com> + * + * Copyright (C) 2005 Red Hat, Inc., James Morris <jmorris@redhat.com> + * Copyright (C) 2006 Trusted Computer Solutions, Inc. <dgoeddel@trustedcs.com> + * Copyright (C) 2006 IBM Corporation, Timothy R. Chavez <tinytim@us.ibm.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2, + * as published by the Free Software Foundation. + */ +#ifndef _LINUX_SELINUX_H +#define _LINUX_SELINUX_H + +struct selinux_audit_rule; +struct audit_context; +struct inode; +struct kern_ipc_perm; + +#ifdef CONFIG_SECURITY_SELINUX + +/** + * selinux_audit_rule_init - alloc/init an selinux audit rule structure. + * @field: the field this rule refers to + * @op: the operater the rule uses + * @rulestr: the text "target" of the rule + * @rule: pointer to the new rule structure returned via this + * + * Returns 0 if successful, -errno if not. On success, the rule structure + * will be allocated internally. The caller must free this structure with + * selinux_audit_rule_free() after use. + */ +int selinux_audit_rule_init(u32 field, u32 op, char *rulestr, + struct selinux_audit_rule **rule); + +/** + * selinux_audit_rule_free - free an selinux audit rule structure. + * @rule: pointer to the audit rule to be freed + * + * This will free all memory associated with the given rule. + * If @rule is NULL, no operation is performed. + */ +void selinux_audit_rule_free(struct selinux_audit_rule *rule); + +/** + * selinux_audit_rule_match - determine if a context ID matches a rule. + * @ctxid: the context ID to check + * @field: the field this rule refers to + * @op: the operater the rule uses + * @rule: pointer to the audit rule to check against + * @actx: the audit context (can be NULL) associated with the check + * + * Returns 1 if the context id matches the rule, 0 if it does not, and + * -errno on failure. + */ +int selinux_audit_rule_match(u32 ctxid, u32 field, u32 op, + struct selinux_audit_rule *rule, + struct audit_context *actx); + +/** + * selinux_audit_set_callback - set the callback for policy reloads. + * @callback: the function to call when the policy is reloaded + * + * This sets the function callback function that will update the rules + * upon policy reloads. This callback should rebuild all existing rules + * using selinux_audit_rule_init(). + */ +void selinux_audit_set_callback(int (*callback)(void)); + +/** + * selinux_task_ctxid - determine a context ID for a process. + * @tsk: the task object + * @ctxid: ID value returned via this + * + * On return, ctxid will contain an ID for the context. This value + * should only be used opaquely. + */ +void selinux_task_ctxid(struct task_struct *tsk, u32 *ctxid); + +/** + * selinux_ctxid_to_string - map a security context ID to a string + * @ctxid: security context ID to be converted. + * @ctx: address of context string to be returned + * @ctxlen: length of returned context string. + * + * Returns 0 if successful, -errno if not. On success, the context + * string will be allocated internally, and the caller must call + * kfree() on it after use. + */ +int selinux_ctxid_to_string(u32 ctxid, char **ctx, u32 *ctxlen); + +/** + * selinux_get_inode_sid - get the inode's security context ID + * @inode: inode structure to get the sid from. + * @sid: pointer to security context ID to be filled in. + * + * Returns nothing + */ +void selinux_get_inode_sid(const struct inode *inode, u32 *sid); + +/** + * selinux_get_ipc_sid - get the ipc security context ID + * @ipcp: ipc structure to get the sid from. + * @sid: pointer to security context ID to be filled in. + * + * Returns nothing + */ +void selinux_get_ipc_sid(const struct kern_ipc_perm *ipcp, u32 *sid); + +/** + * selinux_get_task_sid - return the SID of task + * @tsk: the task whose SID will be returned + * @sid: pointer to security context ID to be filled in. + * + * Returns nothing + */ +void selinux_get_task_sid(struct task_struct *tsk, u32 *sid); + + +#else + +static inline int selinux_audit_rule_init(u32 field, u32 op, + char *rulestr, + struct selinux_audit_rule **rule) +{ + return -ENOTSUPP; +} + +static inline void selinux_audit_rule_free(struct selinux_audit_rule *rule) +{ + return; +} + +static inline int selinux_audit_rule_match(u32 ctxid, u32 field, u32 op, + struct selinux_audit_rule *rule, + struct audit_context *actx) +{ + return 0; +} + +static inline void selinux_audit_set_callback(int (*callback)(void)) +{ + return; +} + +static inline void selinux_task_ctxid(struct task_struct *tsk, u32 *ctxid) +{ + *ctxid = 0; +} + +static inline int selinux_ctxid_to_string(u32 ctxid, char **ctx, u32 *ctxlen) +{ + *ctx = NULL; + *ctxlen = 0; + return 0; +} + +static inline void selinux_get_inode_sid(const struct inode *inode, u32 *sid) +{ + *sid = 0; +} + +static inline void selinux_get_ipc_sid(const struct kern_ipc_perm *ipcp, u32 *sid) +{ + *sid = 0; +} + +static inline void selinux_get_task_sid(struct task_struct *tsk, u32 *sid) +{ + *sid = 0; +} + +#endif /* CONFIG_SECURITY_SELINUX */ + +#endif /* _LINUX_SELINUX_H */ diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index c32e60e79de..bd14858121e 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -254,6 +254,7 @@ struct uart_port { #define UPF_CONS_FLOW ((__force upf_t) (1 << 23)) #define UPF_SHARE_IRQ ((__force upf_t) (1 << 24)) #define UPF_BOOT_AUTOCONF ((__force upf_t) (1 << 28)) +#define UPF_DEAD ((__force upf_t) (1 << 30)) #define UPF_IOREMAP ((__force upf_t) (1 << 31)) #define UPF_CHANGE_MASK ((__force upf_t) (0x17fff)) diff --git a/include/linux/signal.h b/include/linux/signal.h index 162a8fd10b2..70739f51a09 100644 --- a/include/linux/signal.h +++ b/include/linux/signal.h @@ -14,10 +14,12 @@ * * SA_INTERRUPT is also used by the irq handling routines. * SA_SHIRQ is for shared interrupt support on PCI and EISA. + * SA_PROBEIRQ is set by callers when they expect sharing mismatches to occur */ -#define SA_PROBE SA_ONESHOT #define SA_SAMPLE_RANDOM SA_RESTART #define SA_SHIRQ 0x04000000 +#define SA_PROBEIRQ 0x08000000 + /* * As above, these correspond to the IORESOURCE_IRQ_* defines in * linux/ioport.h to select the interrupt line behaviour. When diff --git a/include/linux/spi/ads7846.h b/include/linux/spi/ads7846.h index 72261e0f2ac..adb3dafd33e 100644 --- a/include/linux/spi/ads7846.h +++ b/include/linux/spi/ads7846.h @@ -14,5 +14,12 @@ struct ads7846_platform_data { u16 x_min, x_max; u16 y_min, y_max; u16 pressure_min, pressure_max; + + u16 debounce_max; /* max number of additional readings + * per sample */ + u16 debounce_tol; /* tolerance used for filtering */ + u16 debounce_rep; /* additional consecutive good readings + * required after the first two */ + int (*get_pendown_state)(void); }; diff --git a/include/net/ax25.h b/include/net/ax25.h index d052b221dbc..5bd99748705 100644 --- a/include/net/ax25.h +++ b/include/net/ax25.h @@ -145,14 +145,14 @@ enum { #define AX25_DEF_CONMODE 2 /* Connected mode allowed */ #define AX25_DEF_WINDOW 2 /* Window=2 */ #define AX25_DEF_EWINDOW 32 /* Module-128 Window=32 */ -#define AX25_DEF_T1 (10 * HZ) /* T1=10s */ -#define AX25_DEF_T2 (3 * HZ) /* T2=3s */ -#define AX25_DEF_T3 (300 * HZ) /* T3=300s */ +#define AX25_DEF_T1 10000 /* T1=10s */ +#define AX25_DEF_T2 3000 /* T2=3s */ +#define AX25_DEF_T3 300000 /* T3=300s */ #define AX25_DEF_N2 10 /* N2=10 */ -#define AX25_DEF_IDLE (0 * 60 * HZ) /* Idle=None */ +#define AX25_DEF_IDLE 0 /* Idle=None */ #define AX25_DEF_PACLEN 256 /* Paclen=256 */ #define AX25_DEF_PROTOCOL AX25_PROTO_STD_SIMPLEX /* Standard AX.25 */ -#define AX25_DEF_DS_TIMEOUT (3 * 60 * HZ) /* DAMA timeout 3 minutes */ +#define AX25_DEF_DS_TIMEOUT 180000 /* DAMA timeout 3 minutes */ typedef struct ax25_uid_assoc { struct hlist_node uid_node; diff --git a/include/net/ieee80211.h b/include/net/ieee80211.h index 4725ff861c5..d5926bfb1fc 100644 --- a/include/net/ieee80211.h +++ b/include/net/ieee80211.h @@ -955,11 +955,13 @@ enum ieee80211_state { #define IEEE80211_24GHZ_MIN_CHANNEL 1 #define IEEE80211_24GHZ_MAX_CHANNEL 14 -#define IEEE80211_24GHZ_CHANNELS 14 +#define IEEE80211_24GHZ_CHANNELS (IEEE80211_24GHZ_MAX_CHANNEL - \ + IEEE80211_24GHZ_MIN_CHANNEL + 1) #define IEEE80211_52GHZ_MIN_CHANNEL 34 #define IEEE80211_52GHZ_MAX_CHANNEL 165 -#define IEEE80211_52GHZ_CHANNELS 131 +#define IEEE80211_52GHZ_CHANNELS (IEEE80211_52GHZ_MAX_CHANNEL - \ + IEEE80211_52GHZ_MIN_CHANNEL + 1) enum { IEEE80211_CH_PASSIVE_ONLY = (1 << 0), diff --git a/include/net/ieee80211softmac.h b/include/net/ieee80211softmac.h index b1ebfbae397..052ed596a4e 100644 --- a/include/net/ieee80211softmac.h +++ b/include/net/ieee80211softmac.h @@ -204,7 +204,8 @@ struct ieee80211softmac_device { /* couple of flags */ u8 scanning:1, /* protects scanning from being done multiple times at once */ - associated:1; + associated:1, + running:1; struct ieee80211softmac_scaninfo *scaninfo; struct ieee80211softmac_assoc_info associnfo; diff --git a/include/net/inet_timewait_sock.h b/include/net/inet_timewait_sock.h index 1da294c4752..e837f98fdb5 100644 --- a/include/net/inet_timewait_sock.h +++ b/include/net/inet_timewait_sock.h @@ -150,7 +150,7 @@ static inline void inet_twsk_add_bind_node(struct inet_timewait_sock *tw, static inline int inet_twsk_dead_hashed(const struct inet_timewait_sock *tw) { - return tw->tw_death_node.pprev != NULL; + return !hlist_unhashed(&tw->tw_death_node); } static inline void inet_twsk_dead_node_init(struct inet_timewait_sock *tw) diff --git a/include/net/netrom.h b/include/net/netrom.h index a5ee53bce62..e0ca112024a 100644 --- a/include/net/netrom.h +++ b/include/net/netrom.h @@ -42,11 +42,11 @@ enum { #define NR_COND_PEER_RX_BUSY 0x04 #define NR_COND_OWN_RX_BUSY 0x08 -#define NR_DEFAULT_T1 (120 * HZ) /* Outstanding frames - 120 seconds */ -#define NR_DEFAULT_T2 (5 * HZ) /* Response delay - 5 seconds */ +#define NR_DEFAULT_T1 120000 /* Outstanding frames - 120 seconds */ +#define NR_DEFAULT_T2 5000 /* Response delay - 5 seconds */ #define NR_DEFAULT_N2 3 /* Number of Retries - 3 */ -#define NR_DEFAULT_T4 (180 * HZ) /* Busy Delay - 180 seconds */ -#define NR_DEFAULT_IDLE (0 * 60 * HZ) /* No Activity Timeout - none */ +#define NR_DEFAULT_T4 180000 /* Busy Delay - 180 seconds */ +#define NR_DEFAULT_IDLE 0 /* No Activity Timeout - none */ #define NR_DEFAULT_WINDOW 4 /* Default Window Size - 4 */ #define NR_DEFAULT_OBS 6 /* Default Obsolescence Count - 6 */ #define NR_DEFAULT_QUAL 10 /* Default Neighbour Quality - 10 */ diff --git a/include/net/rose.h b/include/net/rose.h index 3249b979605..012b09ed240 100644 --- a/include/net/rose.h +++ b/include/net/rose.h @@ -49,14 +49,14 @@ enum { ROSE_STATE_5 /* Deferred Call Acceptance */ }; -#define ROSE_DEFAULT_T0 (180 * HZ) /* Default T10 T20 value */ -#define ROSE_DEFAULT_T1 (200 * HZ) /* Default T11 T21 value */ -#define ROSE_DEFAULT_T2 (180 * HZ) /* Default T12 T22 value */ -#define ROSE_DEFAULT_T3 (180 * HZ) /* Default T13 T23 value */ -#define ROSE_DEFAULT_HB (5 * HZ) /* Default Holdback value */ -#define ROSE_DEFAULT_IDLE (0 * 60 * HZ) /* No Activity Timeout - none */ +#define ROSE_DEFAULT_T0 180000 /* Default T10 T20 value */ +#define ROSE_DEFAULT_T1 200000 /* Default T11 T21 value */ +#define ROSE_DEFAULT_T2 180000 /* Default T12 T22 value */ +#define ROSE_DEFAULT_T3 180000 /* Default T13 T23 value */ +#define ROSE_DEFAULT_HB 5000 /* Default Holdback value */ +#define ROSE_DEFAULT_IDLE 0 /* No Activity Timeout - none */ #define ROSE_DEFAULT_ROUTING 1 /* Default routing flag */ -#define ROSE_DEFAULT_FAIL_TIMEOUT (120 * HZ) /* Time until link considered usable */ +#define ROSE_DEFAULT_FAIL_TIMEOUT 120000 /* Time until link considered usable */ #define ROSE_DEFAULT_MAXVC 50 /* Maximum number of VCs per neighbour */ #define ROSE_DEFAULT_WINDOW_SIZE 7 /* Default window size */ diff --git a/include/net/sctp/structs.h b/include/net/sctp/structs.h index eba99f37551..7f4fea173fb 100644 --- a/include/net/sctp/structs.h +++ b/include/net/sctp/structs.h @@ -712,6 +712,7 @@ struct sctp_chunk { __u8 tsn_gap_acked; /* Is this chunk acked by a GAP ACK? */ __s8 fast_retransmit; /* Is this chunk fast retransmitted? */ __u8 tsn_missing_report; /* Data chunk missing counter. */ + __u8 data_accepted; /* At least 1 chunk in this packet accepted */ }; void sctp_chunk_hold(struct sctp_chunk *); diff --git a/include/net/sock.h b/include/net/sock.h index ff8b0dad7b0..c9fad6fb629 100644 --- a/include/net/sock.h +++ b/include/net/sock.h @@ -279,7 +279,7 @@ static inline int sk_unhashed(const struct sock *sk) static inline int sk_hashed(const struct sock *sk) { - return sk->sk_node.pprev != NULL; + return !sk_unhashed(sk); } static __inline__ void sk_node_init(struct hlist_node *node) diff --git a/include/scsi/srp.h b/include/scsi/srp.h index 6c2681dc5b4..637f77eccf0 100644 --- a/include/scsi/srp.h +++ b/include/scsi/srp.h @@ -95,14 +95,15 @@ struct srp_direct_buf { /* * We need the packed attribute because the SRP spec puts the list of - * descriptors at an offset of 20, which is not aligned to the size - * of struct srp_direct_buf. + * descriptors at an offset of 20, which is not aligned to the size of + * struct srp_direct_buf. The whole structure must be packed to avoid + * having the 20-byte structure padded to 24 bytes on 64-bit architectures. */ struct srp_indirect_buf { struct srp_direct_buf table_desc; __be32 len; - struct srp_direct_buf desc_list[0] __attribute__((packed)); -}; + struct srp_direct_buf desc_list[0]; +} __attribute__((packed)); enum { SRP_MULTICHAN_SINGLE = 0, @@ -122,6 +123,11 @@ struct srp_login_req { u8 target_port_id[16]; }; +/* + * The SRP spec defines the size of the LOGIN_RSP structure to be 52 + * bytes, so it needs to be packed to avoid having it padded to 56 + * bytes on 64-bit architectures. + */ struct srp_login_rsp { u8 opcode; u8 reserved1[3]; @@ -132,7 +138,7 @@ struct srp_login_rsp { __be16 buf_fmt; u8 rsp_flags; u8 reserved2[25]; -}; +} __attribute__((packed)); struct srp_login_rej { u8 opcode; @@ -207,6 +213,11 @@ enum { SRP_RSP_FLAG_DIUNDER = 1 << 5 }; +/* + * The SRP spec defines the size of the RSP structure to be 36 bytes, + * so it needs to be packed to avoid having it padded to 40 bytes on + * 64-bit architectures. + */ struct srp_rsp { u8 opcode; u8 sol_not; @@ -221,6 +232,6 @@ struct srp_rsp { __be32 sense_data_len; __be32 resp_data_len; u8 data[0]; -}; +} __attribute__((packed)); #endif /* SCSI_SRP_H */ diff --git a/include/sound/pcm.h b/include/sound/pcm.h index df70e7592ab..373425895fa 100644 --- a/include/sound/pcm.h +++ b/include/sound/pcm.h @@ -374,12 +374,14 @@ struct snd_pcm_substream { /* -- OSS things -- */ struct snd_pcm_oss_substream oss; #endif +#ifdef CONFIG_SND_VERBOSE_PROCFS struct snd_info_entry *proc_root; struct snd_info_entry *proc_info_entry; struct snd_info_entry *proc_hw_params_entry; struct snd_info_entry *proc_sw_params_entry; struct snd_info_entry *proc_status_entry; struct snd_info_entry *proc_prealloc_entry; +#endif /* misc flags */ unsigned int no_mmap_ctrl: 1; unsigned int hw_opened: 1; @@ -400,12 +402,14 @@ struct snd_pcm_str { struct snd_pcm_oss_stream oss; #endif struct snd_pcm_file *files; +#ifdef CONFIG_SND_VERBOSE_PROCFS struct snd_info_entry *proc_root; struct snd_info_entry *proc_info_entry; -#ifdef CONFIG_SND_DEBUG +#ifdef CONFIG_SND_PCM_XRUN_DEBUG unsigned int xrun_debug; /* 0 = disabled, 1 = verbose, 2 = stacktrace */ struct snd_info_entry *proc_xrun_debug_entry; #endif +#endif }; struct snd_pcm { diff --git a/include/sound/pcm_oss.h b/include/sound/pcm_oss.h index 39df2baca18..c854647b6f3 100644 --- a/include/sound/pcm_oss.h +++ b/include/sound/pcm_oss.h @@ -75,7 +75,9 @@ struct snd_pcm_oss_substream { struct snd_pcm_oss_stream { struct snd_pcm_oss_setup *setup_list; /* setup list */ struct mutex setup_mutex; +#ifdef CONFIG_SND_VERBOSE_PROCFS struct snd_info_entry *proc_entry; +#endif }; struct snd_pcm_oss { diff --git a/init/main.c b/init/main.c index 4a2f0898dda..f715b9b8975 100644 --- a/init/main.c +++ b/init/main.c @@ -582,7 +582,7 @@ static void __init do_initcalls(void) result = (*call)(); - if (result && (result != -ENODEV || initcall_debug)) { + if (result && result != -ENODEV && initcall_debug) { sprintf(msgbuf, "error code %d", result); msg = msgbuf; } diff --git a/ipc/msg.c b/ipc/msg.c index 48a7f17a723..7d1340ccb16 100644 --- a/ipc/msg.c +++ b/ipc/msg.c @@ -13,6 +13,9 @@ * mostly rewritten, threaded and wake-one semantics added * MSGMAX limit removed, sysctl's added * (c) 1999 Manfred Spraul <manfred@colorfullife.com> + * + * support for audit of ipc object properties and permission changes + * Dustin Kirkland <dustin.kirkland@us.ibm.com> */ #include <linux/capability.h> @@ -447,6 +450,11 @@ asmlinkage long sys_msgctl (int msqid, int cmd, struct msqid_ds __user *buf) if (msg_checkid(msq,msqid)) goto out_unlock_up; ipcp = &msq->q_perm; + + err = audit_ipc_obj(ipcp); + if (err) + goto out_unlock_up; + err = -EPERM; if (current->euid != ipcp->cuid && current->euid != ipcp->uid && !capable(CAP_SYS_ADMIN)) @@ -460,7 +468,8 @@ asmlinkage long sys_msgctl (int msqid, int cmd, struct msqid_ds __user *buf) switch (cmd) { case IPC_SET: { - if ((err = audit_ipc_perms(setbuf.qbytes, setbuf.uid, setbuf.gid, setbuf.mode, ipcp))) + err = audit_ipc_set_perm(setbuf.qbytes, setbuf.uid, setbuf.gid, setbuf.mode, ipcp); + if (err) goto out_unlock_up; err = -EPERM; diff --git a/ipc/sem.c b/ipc/sem.c index 642659cd596..7919f8ece6b 100644 --- a/ipc/sem.c +++ b/ipc/sem.c @@ -61,6 +61,9 @@ * (c) 2001 Red Hat Inc <alan@redhat.com> * Lockless wakeup * (c) 2003 Manfred Spraul <manfred@colorfullife.com> + * + * support for audit of ipc object properties and permission changes + * Dustin Kirkland <dustin.kirkland@us.ibm.com> */ #include <linux/config.h> @@ -820,6 +823,11 @@ static int semctl_down(int semid, int semnum, int cmd, int version, union semun goto out_unlock; } ipcp = &sma->sem_perm; + + err = audit_ipc_obj(ipcp); + if (err) + goto out_unlock; + if (current->euid != ipcp->cuid && current->euid != ipcp->uid && !capable(CAP_SYS_ADMIN)) { err=-EPERM; @@ -836,7 +844,8 @@ static int semctl_down(int semid, int semnum, int cmd, int version, union semun err = 0; break; case IPC_SET: - if ((err = audit_ipc_perms(0, setbuf.uid, setbuf.gid, setbuf.mode, ipcp))) + err = audit_ipc_set_perm(0, setbuf.uid, setbuf.gid, setbuf.mode, ipcp); + if (err) goto out_unlock; ipcp->uid = setbuf.uid; ipcp->gid = setbuf.gid; diff --git a/ipc/shm.c b/ipc/shm.c index 1c2faf62bc7..80989685190 100644 --- a/ipc/shm.c +++ b/ipc/shm.c @@ -13,6 +13,8 @@ * Shared /dev/zero support, Kanoj Sarcar <kanoj@sgi.com> * Move the mm functionality over to mm/shmem.c, Christoph Rohland <cr@sap.com> * + * support for audit of ipc object properties and permission changes + * Dustin Kirkland <dustin.kirkland@us.ibm.com> */ #include <linux/config.h> @@ -542,6 +544,10 @@ asmlinkage long sys_shmctl (int shmid, int cmd, struct shmid_ds __user *buf) if(err) goto out_unlock; + err = audit_ipc_obj(&(shp->shm_perm)); + if (err) + goto out_unlock; + if (!capable(CAP_IPC_LOCK)) { err = -EPERM; if (current->euid != shp->shm_perm.uid && @@ -594,6 +600,10 @@ asmlinkage long sys_shmctl (int shmid, int cmd, struct shmid_ds __user *buf) if(err) goto out_unlock_up; + err = audit_ipc_obj(&(shp->shm_perm)); + if (err) + goto out_unlock_up; + if (current->euid != shp->shm_perm.uid && current->euid != shp->shm_perm.cuid && !capable(CAP_SYS_ADMIN)) { @@ -627,12 +637,15 @@ asmlinkage long sys_shmctl (int shmid, int cmd, struct shmid_ds __user *buf) err=-EINVAL; if(shp==NULL) goto out_up; - if ((err = audit_ipc_perms(0, setbuf.uid, setbuf.gid, - setbuf.mode, &(shp->shm_perm)))) - goto out_unlock_up; err = shm_checkid(shp,shmid); if(err) goto out_unlock_up; + err = audit_ipc_obj(&(shp->shm_perm)); + if (err) + goto out_unlock_up; + err = audit_ipc_set_perm(0, setbuf.uid, setbuf.gid, setbuf.mode, &(shp->shm_perm)); + if (err) + goto out_unlock_up; err=-EPERM; if (current->euid != shp->shm_perm.uid && current->euid != shp->shm_perm.cuid && diff --git a/ipc/util.c b/ipc/util.c index b3dcfad3b4f..8193299f45f 100644 --- a/ipc/util.c +++ b/ipc/util.c @@ -10,6 +10,8 @@ * Manfred Spraul <manfred@colorfullife.com> * Oct 2002 - One lock per IPC id. RCU ipc_free for lock-free grow_ary(). * Mingming Cao <cmm@us.ibm.com> + * Mar 2006 - support for audit of ipc object properties + * Dustin Kirkland <dustin.kirkland@us.ibm.com> */ #include <linux/config.h> @@ -27,6 +29,7 @@ #include <linux/workqueue.h> #include <linux/seq_file.h> #include <linux/proc_fs.h> +#include <linux/audit.h> #include <asm/unistd.h> @@ -464,8 +467,10 @@ void ipc_rcu_putref(void *ptr) int ipcperms (struct kern_ipc_perm *ipcp, short flag) { /* flag will most probably be 0 or S_...UGO from <linux/stat.h> */ - int requested_mode, granted_mode; + int requested_mode, granted_mode, err; + if (unlikely((err = audit_ipc_obj(ipcp)))) + return err; requested_mode = (flag >> 6) | (flag >> 3) | flag; granted_mode = ipcp->mode; if (current->euid == ipcp->cuid || current->euid == ipcp->uid) diff --git a/kernel/audit.c b/kernel/audit.c index c8ccbd09048..df57b493e1c 100644 --- a/kernel/audit.c +++ b/kernel/audit.c @@ -55,6 +55,9 @@ #include <net/netlink.h> #include <linux/skbuff.h> #include <linux/netlink.h> +#include <linux/selinux.h> + +#include "audit.h" /* No auditing will take place until audit_initialized != 0. * (Initialization happens after skb_init is called.) */ @@ -227,49 +230,103 @@ void audit_log_lost(const char *message) } } -static int audit_set_rate_limit(int limit, uid_t loginuid) +static int audit_set_rate_limit(int limit, uid_t loginuid, u32 sid) { - int old = audit_rate_limit; - audit_rate_limit = limit; - audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + int old = audit_rate_limit; + + if (sid) { + char *ctx = NULL; + u32 len; + int rc; + if ((rc = selinux_ctxid_to_string(sid, &ctx, &len))) + return rc; + else + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + "audit_rate_limit=%d old=%d by auid=%u subj=%s", + limit, old, loginuid, ctx); + kfree(ctx); + } else + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, "audit_rate_limit=%d old=%d by auid=%u", - audit_rate_limit, old, loginuid); + limit, old, loginuid); + audit_rate_limit = limit; return old; } -static int audit_set_backlog_limit(int limit, uid_t loginuid) +static int audit_set_backlog_limit(int limit, uid_t loginuid, u32 sid) { - int old = audit_backlog_limit; - audit_backlog_limit = limit; - audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + int old = audit_backlog_limit; + + if (sid) { + char *ctx = NULL; + u32 len; + int rc; + if ((rc = selinux_ctxid_to_string(sid, &ctx, &len))) + return rc; + else + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + "audit_backlog_limit=%d old=%d by auid=%u subj=%s", + limit, old, loginuid, ctx); + kfree(ctx); + } else + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, "audit_backlog_limit=%d old=%d by auid=%u", - audit_backlog_limit, old, loginuid); + limit, old, loginuid); + audit_backlog_limit = limit; return old; } -static int audit_set_enabled(int state, uid_t loginuid) +static int audit_set_enabled(int state, uid_t loginuid, u32 sid) { - int old = audit_enabled; + int old = audit_enabled; + if (state != 0 && state != 1) return -EINVAL; - audit_enabled = state; - audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + + if (sid) { + char *ctx = NULL; + u32 len; + int rc; + if ((rc = selinux_ctxid_to_string(sid, &ctx, &len))) + return rc; + else + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + "audit_enabled=%d old=%d by auid=%u subj=%s", + state, old, loginuid, ctx); + kfree(ctx); + } else + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, "audit_enabled=%d old=%d by auid=%u", - audit_enabled, old, loginuid); + state, old, loginuid); + audit_enabled = state; return old; } -static int audit_set_failure(int state, uid_t loginuid) +static int audit_set_failure(int state, uid_t loginuid, u32 sid) { - int old = audit_failure; + int old = audit_failure; + if (state != AUDIT_FAIL_SILENT && state != AUDIT_FAIL_PRINTK && state != AUDIT_FAIL_PANIC) return -EINVAL; - audit_failure = state; - audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + + if (sid) { + char *ctx = NULL; + u32 len; + int rc; + if ((rc = selinux_ctxid_to_string(sid, &ctx, &len))) + return rc; + else + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + "audit_failure=%d old=%d by auid=%u subj=%s", + state, old, loginuid, ctx); + kfree(ctx); + } else + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, "audit_failure=%d old=%d by auid=%u", - audit_failure, old, loginuid); + state, old, loginuid); + audit_failure = state; return old; } @@ -387,7 +444,7 @@ static int audit_netlink_ok(kernel_cap_t eff_cap, u16 msg_type) static int audit_receive_msg(struct sk_buff *skb, struct nlmsghdr *nlh) { - u32 uid, pid, seq; + u32 uid, pid, seq, sid; void *data; struct audit_status *status_get, status_set; int err; @@ -413,6 +470,7 @@ static int audit_receive_msg(struct sk_buff *skb, struct nlmsghdr *nlh) pid = NETLINK_CREDS(skb)->pid; uid = NETLINK_CREDS(skb)->uid; loginuid = NETLINK_CB(skb).loginuid; + sid = NETLINK_CB(skb).sid; seq = nlh->nlmsg_seq; data = NLMSG_DATA(nlh); @@ -433,25 +491,43 @@ static int audit_receive_msg(struct sk_buff *skb, struct nlmsghdr *nlh) return -EINVAL; status_get = (struct audit_status *)data; if (status_get->mask & AUDIT_STATUS_ENABLED) { - err = audit_set_enabled(status_get->enabled, loginuid); + err = audit_set_enabled(status_get->enabled, + loginuid, sid); if (err < 0) return err; } if (status_get->mask & AUDIT_STATUS_FAILURE) { - err = audit_set_failure(status_get->failure, loginuid); + err = audit_set_failure(status_get->failure, + loginuid, sid); if (err < 0) return err; } if (status_get->mask & AUDIT_STATUS_PID) { int old = audit_pid; + if (sid) { + char *ctx = NULL; + u32 len; + int rc; + if ((rc = selinux_ctxid_to_string( + sid, &ctx, &len))) + return rc; + else + audit_log(NULL, GFP_KERNEL, + AUDIT_CONFIG_CHANGE, + "audit_pid=%d old=%d by auid=%u subj=%s", + status_get->pid, old, + loginuid, ctx); + kfree(ctx); + } else + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + "audit_pid=%d old=%d by auid=%u", + status_get->pid, old, loginuid); audit_pid = status_get->pid; - audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, - "audit_pid=%d old=%d by auid=%u", - audit_pid, old, loginuid); } if (status_get->mask & AUDIT_STATUS_RATE_LIMIT) - audit_set_rate_limit(status_get->rate_limit, loginuid); + audit_set_rate_limit(status_get->rate_limit, + loginuid, sid); if (status_get->mask & AUDIT_STATUS_BACKLOG_LIMIT) audit_set_backlog_limit(status_get->backlog_limit, - loginuid); + loginuid, sid); break; case AUDIT_USER: case AUDIT_FIRST_USER_MSG...AUDIT_LAST_USER_MSG: @@ -465,8 +541,23 @@ static int audit_receive_msg(struct sk_buff *skb, struct nlmsghdr *nlh) ab = audit_log_start(NULL, GFP_KERNEL, msg_type); if (ab) { audit_log_format(ab, - "user pid=%d uid=%u auid=%u msg='%.1024s'", - pid, uid, loginuid, (char *)data); + "user pid=%d uid=%u auid=%u", + pid, uid, loginuid); + if (sid) { + char *ctx = NULL; + u32 len; + if (selinux_ctxid_to_string( + sid, &ctx, &len)) { + audit_log_format(ab, + " ssid=%u", sid); + /* Maybe call audit_panic? */ + } else + audit_log_format(ab, + " subj=%s", ctx); + kfree(ctx); + } + audit_log_format(ab, " msg='%.1024s'", + (char *)data); audit_set_pid(ab, pid); audit_log_end(ab); } @@ -480,7 +571,7 @@ static int audit_receive_msg(struct sk_buff *skb, struct nlmsghdr *nlh) case AUDIT_LIST: err = audit_receive_filter(nlh->nlmsg_type, NETLINK_CB(skb).pid, uid, seq, data, nlmsg_len(nlh), - loginuid); + loginuid, sid); break; case AUDIT_ADD_RULE: case AUDIT_DEL_RULE: @@ -490,7 +581,7 @@ static int audit_receive_msg(struct sk_buff *skb, struct nlmsghdr *nlh) case AUDIT_LIST_RULES: err = audit_receive_filter(nlh->nlmsg_type, NETLINK_CB(skb).pid, uid, seq, data, nlmsg_len(nlh), - loginuid); + loginuid, sid); break; case AUDIT_SIGNAL_INFO: sig_data.uid = audit_sig_uid; @@ -564,6 +655,11 @@ static int __init audit_init(void) skb_queue_head_init(&audit_skb_queue); audit_initialized = 1; audit_enabled = audit_default; + + /* Register the callback with selinux. This callback will be invoked + * when a new policy is loaded. */ + selinux_audit_set_callback(&selinux_audit_rule_update); + audit_log(NULL, GFP_KERNEL, AUDIT_KERNEL, "initialized"); return 0; } diff --git a/kernel/audit.h b/kernel/audit.h index bc5392076e2..6f733920fd3 100644 --- a/kernel/audit.h +++ b/kernel/audit.h @@ -54,9 +54,11 @@ enum audit_state { /* Rule lists */ struct audit_field { - u32 type; - u32 val; - u32 op; + u32 type; + u32 val; + u32 op; + char *se_str; + struct selinux_audit_rule *se_rule; }; struct audit_krule { @@ -86,3 +88,5 @@ extern void audit_send_reply(int pid, int seq, int type, extern void audit_log_lost(const char *message); extern void audit_panic(const char *message); extern struct mutex audit_netlink_mutex; + +extern int selinux_audit_rule_update(void); diff --git a/kernel/auditfilter.c b/kernel/auditfilter.c index d3a8539f3a8..7c134906d68 100644 --- a/kernel/auditfilter.c +++ b/kernel/auditfilter.c @@ -23,6 +23,7 @@ #include <linux/audit.h> #include <linux/kthread.h> #include <linux/netlink.h> +#include <linux/selinux.h> #include "audit.h" /* There are three lists of rules -- one to search at task creation @@ -42,6 +43,13 @@ struct list_head audit_filter_list[AUDIT_NR_FILTERS] = { static inline void audit_free_rule(struct audit_entry *e) { + int i; + if (e->rule.fields) + for (i = 0; i < e->rule.field_count; i++) { + struct audit_field *f = &e->rule.fields[i]; + kfree(f->se_str); + selinux_audit_rule_free(f->se_rule); + } kfree(e->rule.fields); kfree(e); } @@ -52,9 +60,29 @@ static inline void audit_free_rule_rcu(struct rcu_head *head) audit_free_rule(e); } +/* Initialize an audit filterlist entry. */ +static inline struct audit_entry *audit_init_entry(u32 field_count) +{ + struct audit_entry *entry; + struct audit_field *fields; + + entry = kzalloc(sizeof(*entry), GFP_KERNEL); + if (unlikely(!entry)) + return NULL; + + fields = kzalloc(sizeof(*fields) * field_count, GFP_KERNEL); + if (unlikely(!fields)) { + kfree(entry); + return NULL; + } + entry->rule.fields = fields; + + return entry; +} + /* Unpack a filter field's string representation from user-space * buffer. */ -static __attribute__((unused)) char *audit_unpack_string(void **bufp, size_t *remain, size_t len) +static char *audit_unpack_string(void **bufp, size_t *remain, size_t len) { char *str; @@ -84,7 +112,6 @@ static inline struct audit_entry *audit_to_entry_common(struct audit_rule *rule) { unsigned listnr; struct audit_entry *entry; - struct audit_field *fields; int i, err; err = -EINVAL; @@ -108,23 +135,14 @@ static inline struct audit_entry *audit_to_entry_common(struct audit_rule *rule) goto exit_err; err = -ENOMEM; - entry = kmalloc(sizeof(*entry), GFP_KERNEL); - if (unlikely(!entry)) - goto exit_err; - fields = kmalloc(sizeof(*fields) * rule->field_count, GFP_KERNEL); - if (unlikely(!fields)) { - kfree(entry); + entry = audit_init_entry(rule->field_count); + if (!entry) goto exit_err; - } - - memset(&entry->rule, 0, sizeof(struct audit_krule)); - memset(fields, 0, sizeof(struct audit_field)); entry->rule.flags = rule->flags & AUDIT_FILTER_PREPEND; entry->rule.listnr = listnr; entry->rule.action = rule->action; entry->rule.field_count = rule->field_count; - entry->rule.fields = fields; for (i = 0; i < AUDIT_BITMASK_SIZE; i++) entry->rule.mask[i] = rule->mask[i]; @@ -150,15 +168,20 @@ static struct audit_entry *audit_rule_to_entry(struct audit_rule *rule) for (i = 0; i < rule->field_count; i++) { struct audit_field *f = &entry->rule.fields[i]; - if (rule->fields[i] & AUDIT_UNUSED_BITS) { - err = -EINVAL; - goto exit_free; - } - f->op = rule->fields[i] & (AUDIT_NEGATE|AUDIT_OPERATORS); f->type = rule->fields[i] & ~(AUDIT_NEGATE|AUDIT_OPERATORS); f->val = rule->values[i]; + if (f->type & AUDIT_UNUSED_BITS || + f->type == AUDIT_SE_USER || + f->type == AUDIT_SE_ROLE || + f->type == AUDIT_SE_TYPE || + f->type == AUDIT_SE_SEN || + f->type == AUDIT_SE_CLR) { + err = -EINVAL; + goto exit_free; + } + entry->rule.vers_ops = (f->op & AUDIT_OPERATORS) ? 2 : 1; /* Support for legacy operators where @@ -188,8 +211,9 @@ static struct audit_entry *audit_data_to_entry(struct audit_rule_data *data, int err = 0; struct audit_entry *entry; void *bufp; - /* size_t remain = datasz - sizeof(struct audit_rule_data); */ + size_t remain = datasz - sizeof(struct audit_rule_data); int i; + char *str; entry = audit_to_entry_common((struct audit_rule *)data); if (IS_ERR(entry)) @@ -207,10 +231,35 @@ static struct audit_entry *audit_data_to_entry(struct audit_rule_data *data, f->op = data->fieldflags[i] & AUDIT_OPERATORS; f->type = data->fields[i]; + f->val = data->values[i]; + f->se_str = NULL; + f->se_rule = NULL; switch(f->type) { - /* call type-specific conversion routines here */ - default: - f->val = data->values[i]; + case AUDIT_SE_USER: + case AUDIT_SE_ROLE: + case AUDIT_SE_TYPE: + case AUDIT_SE_SEN: + case AUDIT_SE_CLR: + str = audit_unpack_string(&bufp, &remain, f->val); + if (IS_ERR(str)) + goto exit_free; + entry->rule.buflen += f->val; + + err = selinux_audit_rule_init(f->type, f->op, str, + &f->se_rule); + /* Keep currently invalid fields around in case they + * become valid after a policy reload. */ + if (err == -EINVAL) { + printk(KERN_WARNING "audit rule for selinux " + "\'%s\' is invalid\n", str); + err = 0; + } + if (err) { + kfree(str); + goto exit_free; + } else + f->se_str = str; + break; } } @@ -286,7 +335,14 @@ static struct audit_rule_data *audit_krule_to_data(struct audit_krule *krule) data->fields[i] = f->type; data->fieldflags[i] = f->op; switch(f->type) { - /* call type-specific conversion routines here */ + case AUDIT_SE_USER: + case AUDIT_SE_ROLE: + case AUDIT_SE_TYPE: + case AUDIT_SE_SEN: + case AUDIT_SE_CLR: + data->buflen += data->values[i] = + audit_pack_string(&bufp, f->se_str); + break; default: data->values[i] = f->val; } @@ -314,7 +370,14 @@ static int audit_compare_rule(struct audit_krule *a, struct audit_krule *b) return 1; switch(a->fields[i].type) { - /* call type-specific comparison routines here */ + case AUDIT_SE_USER: + case AUDIT_SE_ROLE: + case AUDIT_SE_TYPE: + case AUDIT_SE_SEN: + case AUDIT_SE_CLR: + if (strcmp(a->fields[i].se_str, b->fields[i].se_str)) + return 1; + break; default: if (a->fields[i].val != b->fields[i].val) return 1; @@ -328,6 +391,81 @@ static int audit_compare_rule(struct audit_krule *a, struct audit_krule *b) return 0; } +/* Duplicate selinux field information. The se_rule is opaque, so must be + * re-initialized. */ +static inline int audit_dupe_selinux_field(struct audit_field *df, + struct audit_field *sf) +{ + int ret = 0; + char *se_str; + + /* our own copy of se_str */ + se_str = kstrdup(sf->se_str, GFP_KERNEL); + if (unlikely(IS_ERR(se_str))) + return -ENOMEM; + df->se_str = se_str; + + /* our own (refreshed) copy of se_rule */ + ret = selinux_audit_rule_init(df->type, df->op, df->se_str, + &df->se_rule); + /* Keep currently invalid fields around in case they + * become valid after a policy reload. */ + if (ret == -EINVAL) { + printk(KERN_WARNING "audit rule for selinux \'%s\' is " + "invalid\n", df->se_str); + ret = 0; + } + + return ret; +} + +/* Duplicate an audit rule. This will be a deep copy with the exception + * of the watch - that pointer is carried over. The selinux specific fields + * will be updated in the copy. The point is to be able to replace the old + * rule with the new rule in the filterlist, then free the old rule. */ +static struct audit_entry *audit_dupe_rule(struct audit_krule *old) +{ + u32 fcount = old->field_count; + struct audit_entry *entry; + struct audit_krule *new; + int i, err = 0; + + entry = audit_init_entry(fcount); + if (unlikely(!entry)) + return ERR_PTR(-ENOMEM); + + new = &entry->rule; + new->vers_ops = old->vers_ops; + new->flags = old->flags; + new->listnr = old->listnr; + new->action = old->action; + for (i = 0; i < AUDIT_BITMASK_SIZE; i++) + new->mask[i] = old->mask[i]; + new->buflen = old->buflen; + new->field_count = old->field_count; + memcpy(new->fields, old->fields, sizeof(struct audit_field) * fcount); + + /* deep copy this information, updating the se_rule fields, because + * the originals will all be freed when the old rule is freed. */ + for (i = 0; i < fcount; i++) { + switch (new->fields[i].type) { + case AUDIT_SE_USER: + case AUDIT_SE_ROLE: + case AUDIT_SE_TYPE: + case AUDIT_SE_SEN: + case AUDIT_SE_CLR: + err = audit_dupe_selinux_field(&new->fields[i], + &old->fields[i]); + } + if (err) { + audit_free_rule(entry); + return ERR_PTR(err); + } + } + + return entry; +} + /* Add rule to given filterlist if not a duplicate. Protected by * audit_netlink_mutex. */ static inline int audit_add_rule(struct audit_entry *entry, @@ -448,9 +586,10 @@ static int audit_list_rules(void *_dest) * @data: payload data * @datasz: size of payload data * @loginuid: loginuid of sender + * @sid: SE Linux Security ID of sender */ int audit_receive_filter(int type, int pid, int uid, int seq, void *data, - size_t datasz, uid_t loginuid) + size_t datasz, uid_t loginuid, u32 sid) { struct task_struct *tsk; int *dest; @@ -493,9 +632,23 @@ int audit_receive_filter(int type, int pid, int uid, int seq, void *data, err = audit_add_rule(entry, &audit_filter_list[entry->rule.listnr]); - audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, - "auid=%u add rule to list=%d res=%d\n", - loginuid, entry->rule.listnr, !err); + if (sid) { + char *ctx = NULL; + u32 len; + if (selinux_ctxid_to_string(sid, &ctx, &len)) { + /* Maybe call audit_panic? */ + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + "auid=%u ssid=%u add rule to list=%d res=%d", + loginuid, sid, entry->rule.listnr, !err); + } else + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + "auid=%u subj=%s add rule to list=%d res=%d", + loginuid, ctx, entry->rule.listnr, !err); + kfree(ctx); + } else + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + "auid=%u add rule to list=%d res=%d", + loginuid, entry->rule.listnr, !err); if (err) audit_free_rule(entry); @@ -511,9 +664,24 @@ int audit_receive_filter(int type, int pid, int uid, int seq, void *data, err = audit_del_rule(entry, &audit_filter_list[entry->rule.listnr]); - audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, - "auid=%u remove rule from list=%d res=%d\n", - loginuid, entry->rule.listnr, !err); + + if (sid) { + char *ctx = NULL; + u32 len; + if (selinux_ctxid_to_string(sid, &ctx, &len)) { + /* Maybe call audit_panic? */ + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + "auid=%u ssid=%u remove rule from list=%d res=%d", + loginuid, sid, entry->rule.listnr, !err); + } else + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + "auid=%u subj=%s remove rule from list=%d res=%d", + loginuid, ctx, entry->rule.listnr, !err); + kfree(ctx); + } else + audit_log(NULL, GFP_KERNEL, AUDIT_CONFIG_CHANGE, + "auid=%u remove rule from list=%d res=%d", + loginuid, entry->rule.listnr, !err); audit_free_rule(entry); break; @@ -628,3 +796,62 @@ unlock_and_return: rcu_read_unlock(); return result; } + +/* Check to see if the rule contains any selinux fields. Returns 1 if there + are selinux fields specified in the rule, 0 otherwise. */ +static inline int audit_rule_has_selinux(struct audit_krule *rule) +{ + int i; + + for (i = 0; i < rule->field_count; i++) { + struct audit_field *f = &rule->fields[i]; + switch (f->type) { + case AUDIT_SE_USER: + case AUDIT_SE_ROLE: + case AUDIT_SE_TYPE: + case AUDIT_SE_SEN: + case AUDIT_SE_CLR: + return 1; + } + } + + return 0; +} + +/* This function will re-initialize the se_rule field of all applicable rules. + * It will traverse the filter lists serarching for rules that contain selinux + * specific filter fields. When such a rule is found, it is copied, the + * selinux field is re-initialized, and the old rule is replaced with the + * updated rule. */ +int selinux_audit_rule_update(void) +{ + struct audit_entry *entry, *n, *nentry; + int i, err = 0; + + /* audit_netlink_mutex synchronizes the writers */ + mutex_lock(&audit_netlink_mutex); + + for (i = 0; i < AUDIT_NR_FILTERS; i++) { + list_for_each_entry_safe(entry, n, &audit_filter_list[i], list) { + if (!audit_rule_has_selinux(&entry->rule)) + continue; + + nentry = audit_dupe_rule(&entry->rule); + if (unlikely(IS_ERR(nentry))) { + /* save the first error encountered for the + * return value */ + if (!err) + err = PTR_ERR(nentry); + audit_panic("error updating selinux filters"); + list_del_rcu(&entry->list); + } else { + list_replace_rcu(&entry->list, &nentry->list); + } + call_rcu(&entry->rcu, audit_free_rule_rcu); + } + } + + mutex_unlock(&audit_netlink_mutex); + + return err; +} diff --git a/kernel/auditsc.c b/kernel/auditsc.c index 7f160df21a2..1c03a4ed1b2 100644 --- a/kernel/auditsc.c +++ b/kernel/auditsc.c @@ -58,6 +58,7 @@ #include <linux/security.h> #include <linux/list.h> #include <linux/tty.h> +#include <linux/selinux.h> #include "audit.h" @@ -89,7 +90,7 @@ struct audit_names { uid_t uid; gid_t gid; dev_t rdev; - char *ctx; + u32 osid; }; struct audit_aux_data { @@ -106,7 +107,7 @@ struct audit_aux_data_ipcctl { uid_t uid; gid_t gid; mode_t mode; - char *ctx; + u32 osid; }; struct audit_aux_data_socketcall { @@ -167,7 +168,8 @@ static int audit_filter_rules(struct task_struct *tsk, struct audit_context *ctx, enum audit_state *state) { - int i, j; + int i, j, need_sid = 1; + u32 sid; for (i = 0; i < rule->field_count; i++) { struct audit_field *f = &rule->fields[i]; @@ -257,6 +259,27 @@ static int audit_filter_rules(struct task_struct *tsk, if (ctx) result = audit_comparator(ctx->loginuid, f->op, f->val); break; + case AUDIT_SE_USER: + case AUDIT_SE_ROLE: + case AUDIT_SE_TYPE: + case AUDIT_SE_SEN: + case AUDIT_SE_CLR: + /* NOTE: this may return negative values indicating + a temporary error. We simply treat this as a + match for now to avoid losing information that + may be wanted. An error message will also be + logged upon error */ + if (f->se_rule) { + if (need_sid) { + selinux_task_ctxid(tsk, &sid); + need_sid = 0; + } + result = selinux_audit_rule_match(sid, f->type, + f->op, + f->se_rule, + ctx); + } + break; case AUDIT_ARG0: case AUDIT_ARG1: case AUDIT_ARG2: @@ -329,7 +352,6 @@ static enum audit_state audit_filter_syscall(struct task_struct *tsk, return AUDIT_BUILD_CONTEXT; } -/* This should be called with task_lock() held. */ static inline struct audit_context *audit_get_context(struct task_struct *tsk, int return_valid, int return_code) @@ -391,9 +413,6 @@ static inline void audit_free_names(struct audit_context *context) #endif for (i = 0; i < context->name_count; i++) { - char *p = context->names[i].ctx; - context->names[i].ctx = NULL; - kfree(p); if (context->names[i].name) __putname(context->names[i].name); } @@ -416,11 +435,6 @@ static inline void audit_free_aux(struct audit_context *context) dput(axi->dentry); mntput(axi->mnt); } - if ( aux->type == AUDIT_IPC ) { - struct audit_aux_data_ipcctl *axi = (void *)aux; - if (axi->ctx) - kfree(axi->ctx); - } context->aux = aux->next; kfree(aux); @@ -506,7 +520,7 @@ static inline void audit_free_context(struct audit_context *context) printk(KERN_ERR "audit: freed %d contexts\n", count); } -static void audit_log_task_context(struct audit_buffer *ab, gfp_t gfp_mask) +static void audit_log_task_context(struct audit_buffer *ab) { char *ctx = NULL; ssize_t len = 0; @@ -518,7 +532,7 @@ static void audit_log_task_context(struct audit_buffer *ab, gfp_t gfp_mask) return; } - ctx = kmalloc(len, gfp_mask); + ctx = kmalloc(len, GFP_KERNEL); if (!ctx) goto error_path; @@ -536,47 +550,46 @@ error_path: return; } -static void audit_log_task_info(struct audit_buffer *ab, gfp_t gfp_mask) +static void audit_log_task_info(struct audit_buffer *ab, struct task_struct *tsk) { - char name[sizeof(current->comm)]; - struct mm_struct *mm = current->mm; + char name[sizeof(tsk->comm)]; + struct mm_struct *mm = tsk->mm; struct vm_area_struct *vma; - get_task_comm(name, current); + /* tsk == current */ + + get_task_comm(name, tsk); audit_log_format(ab, " comm="); audit_log_untrustedstring(ab, name); - if (!mm) - return; - - /* - * this is brittle; all callers that pass GFP_ATOMIC will have - * NULL current->mm and we won't get here. - */ - down_read(&mm->mmap_sem); - vma = mm->mmap; - while (vma) { - if ((vma->vm_flags & VM_EXECUTABLE) && - vma->vm_file) { - audit_log_d_path(ab, "exe=", - vma->vm_file->f_dentry, - vma->vm_file->f_vfsmnt); - break; + if (mm) { + down_read(&mm->mmap_sem); + vma = mm->mmap; + while (vma) { + if ((vma->vm_flags & VM_EXECUTABLE) && + vma->vm_file) { + audit_log_d_path(ab, "exe=", + vma->vm_file->f_dentry, + vma->vm_file->f_vfsmnt); + break; + } + vma = vma->vm_next; } - vma = vma->vm_next; + up_read(&mm->mmap_sem); } - up_read(&mm->mmap_sem); - audit_log_task_context(ab, gfp_mask); + audit_log_task_context(ab); } -static void audit_log_exit(struct audit_context *context, gfp_t gfp_mask) +static void audit_log_exit(struct audit_context *context, struct task_struct *tsk) { - int i; + int i, call_panic = 0; struct audit_buffer *ab; struct audit_aux_data *aux; const char *tty; - ab = audit_log_start(context, gfp_mask, AUDIT_SYSCALL); + /* tsk == current */ + + ab = audit_log_start(context, GFP_KERNEL, AUDIT_SYSCALL); if (!ab) return; /* audit_panic has been called */ audit_log_format(ab, "arch=%x syscall=%d", @@ -587,8 +600,8 @@ static void audit_log_exit(struct audit_context *context, gfp_t gfp_mask) audit_log_format(ab, " success=%s exit=%ld", (context->return_valid==AUDITSC_SUCCESS)?"yes":"no", context->return_code); - if (current->signal->tty && current->signal->tty->name) - tty = current->signal->tty->name; + if (tsk->signal && tsk->signal->tty && tsk->signal->tty->name) + tty = tsk->signal->tty->name; else tty = "(none)"; audit_log_format(ab, @@ -607,12 +620,12 @@ static void audit_log_exit(struct audit_context *context, gfp_t gfp_mask) context->gid, context->euid, context->suid, context->fsuid, context->egid, context->sgid, context->fsgid, tty); - audit_log_task_info(ab, gfp_mask); + audit_log_task_info(ab, tsk); audit_log_end(ab); for (aux = context->aux; aux; aux = aux->next) { - ab = audit_log_start(context, gfp_mask, aux->type); + ab = audit_log_start(context, GFP_KERNEL, aux->type); if (!ab) continue; /* audit_panic has been called */ @@ -620,8 +633,39 @@ static void audit_log_exit(struct audit_context *context, gfp_t gfp_mask) case AUDIT_IPC: { struct audit_aux_data_ipcctl *axi = (void *)aux; audit_log_format(ab, - " qbytes=%lx iuid=%u igid=%u mode=%x obj=%s", - axi->qbytes, axi->uid, axi->gid, axi->mode, axi->ctx); + " qbytes=%lx iuid=%u igid=%u mode=%x", + axi->qbytes, axi->uid, axi->gid, axi->mode); + if (axi->osid != 0) { + char *ctx = NULL; + u32 len; + if (selinux_ctxid_to_string( + axi->osid, &ctx, &len)) { + audit_log_format(ab, " osid=%u", + axi->osid); + call_panic = 1; + } else + audit_log_format(ab, " obj=%s", ctx); + kfree(ctx); + } + break; } + + case AUDIT_IPC_SET_PERM: { + struct audit_aux_data_ipcctl *axi = (void *)aux; + audit_log_format(ab, + " new qbytes=%lx new iuid=%u new igid=%u new mode=%x", + axi->qbytes, axi->uid, axi->gid, axi->mode); + if (axi->osid != 0) { + char *ctx = NULL; + u32 len; + if (selinux_ctxid_to_string( + axi->osid, &ctx, &len)) { + audit_log_format(ab, " osid=%u", + axi->osid); + call_panic = 1; + } else + audit_log_format(ab, " obj=%s", ctx); + kfree(ctx); + } break; } case AUDIT_SOCKETCALL: { @@ -649,7 +693,7 @@ static void audit_log_exit(struct audit_context *context, gfp_t gfp_mask) } if (context->pwd && context->pwdmnt) { - ab = audit_log_start(context, gfp_mask, AUDIT_CWD); + ab = audit_log_start(context, GFP_KERNEL, AUDIT_CWD); if (ab) { audit_log_d_path(ab, "cwd=", context->pwd, context->pwdmnt); audit_log_end(ab); @@ -659,7 +703,7 @@ static void audit_log_exit(struct audit_context *context, gfp_t gfp_mask) unsigned long ino = context->names[i].ino; unsigned long pino = context->names[i].pino; - ab = audit_log_start(context, gfp_mask, AUDIT_PATH); + ab = audit_log_start(context, GFP_KERNEL, AUDIT_PATH); if (!ab) continue; /* audit_panic has been called */ @@ -685,32 +729,35 @@ static void audit_log_exit(struct audit_context *context, gfp_t gfp_mask) context->names[i].gid, MAJOR(context->names[i].rdev), MINOR(context->names[i].rdev)); - if (context->names[i].ctx) { - audit_log_format(ab, " obj=%s", - context->names[i].ctx); + if (context->names[i].osid != 0) { + char *ctx = NULL; + u32 len; + if (selinux_ctxid_to_string( + context->names[i].osid, &ctx, &len)) { + audit_log_format(ab, " osid=%u", + context->names[i].osid); + call_panic = 2; + } else + audit_log_format(ab, " obj=%s", ctx); + kfree(ctx); } audit_log_end(ab); } + if (call_panic) + audit_panic("error converting sid to string"); } /** * audit_free - free a per-task audit context * @tsk: task whose audit context block to free * - * Called from copy_process and __put_task_struct. + * Called from copy_process and do_exit */ void audit_free(struct task_struct *tsk) { struct audit_context *context; - /* - * No need to lock the task - when we execute audit_free() - * then the task has no external references anymore, and - * we are tearing it down. (The locking also confuses - * DEBUG_LOCKDEP - this freeing may occur in softirq - * contexts as well, via RCU.) - */ context = audit_get_context(tsk, 0, 0); if (likely(!context)) return; @@ -719,8 +766,9 @@ void audit_free(struct task_struct *tsk) * function (e.g., exit_group), then free context block. * We use GFP_ATOMIC here because we might be doing this * in the context of the idle thread */ + /* that can happen only if we are called from do_exit() */ if (context->in_syscall && context->auditable) - audit_log_exit(context, GFP_ATOMIC); + audit_log_exit(context, tsk); audit_free_context(context); } @@ -743,10 +791,11 @@ void audit_free(struct task_struct *tsk) * will only be written if another part of the kernel requests that it * be written). */ -void audit_syscall_entry(struct task_struct *tsk, int arch, int major, +void audit_syscall_entry(int arch, int major, unsigned long a1, unsigned long a2, unsigned long a3, unsigned long a4) { + struct task_struct *tsk = current; struct audit_context *context = tsk->audit_context; enum audit_state state; @@ -824,22 +873,18 @@ void audit_syscall_entry(struct task_struct *tsk, int arch, int major, * message), then write out the syscall information. In call cases, * free the names stored from getname(). */ -void audit_syscall_exit(struct task_struct *tsk, int valid, long return_code) +void audit_syscall_exit(int valid, long return_code) { + struct task_struct *tsk = current; struct audit_context *context; - get_task_struct(tsk); - task_lock(tsk); context = audit_get_context(tsk, valid, return_code); - task_unlock(tsk); - /* Not having a context here is ok, since the parent may have - * called __put_task_struct. */ if (likely(!context)) - goto out; + return; if (context->in_syscall && context->auditable) - audit_log_exit(context, GFP_KERNEL); + audit_log_exit(context, tsk); context->in_syscall = 0; context->auditable = 0; @@ -854,8 +899,6 @@ void audit_syscall_exit(struct task_struct *tsk, int valid, long return_code) audit_free_aux(context); tsk->audit_context = context; } - out: - put_task_struct(tsk); } /** @@ -936,40 +979,11 @@ void audit_putname(const char *name) #endif } -void audit_inode_context(int idx, const struct inode *inode) +static void audit_inode_context(int idx, const struct inode *inode) { struct audit_context *context = current->audit_context; - const char *suffix = security_inode_xattr_getsuffix(); - char *ctx = NULL; - int len = 0; - - if (!suffix) - goto ret; - - len = security_inode_getsecurity(inode, suffix, NULL, 0, 0); - if (len == -EOPNOTSUPP) - goto ret; - if (len < 0) - goto error_path; - - ctx = kmalloc(len, GFP_KERNEL); - if (!ctx) - goto error_path; - len = security_inode_getsecurity(inode, suffix, ctx, len, 0); - if (len < 0) - goto error_path; - - kfree(context->names[idx].ctx); - context->names[idx].ctx = ctx; - goto ret; - -error_path: - if (ctx) - kfree(ctx); - audit_panic("error in audit_inode_context"); -ret: - return; + selinux_get_inode_sid(inode, &context->names[idx].osid); } @@ -1155,40 +1169,37 @@ uid_t audit_get_loginuid(struct audit_context *ctx) return ctx ? ctx->loginuid : -1; } -static char *audit_ipc_context(struct kern_ipc_perm *ipcp) +/** + * audit_ipc_obj - record audit data for ipc object + * @ipcp: ipc permissions + * + * Returns 0 for success or NULL context or < 0 on error. + */ +int audit_ipc_obj(struct kern_ipc_perm *ipcp) { + struct audit_aux_data_ipcctl *ax; struct audit_context *context = current->audit_context; - char *ctx = NULL; - int len = 0; if (likely(!context)) - return NULL; - - len = security_ipc_getsecurity(ipcp, NULL, 0); - if (len == -EOPNOTSUPP) - goto ret; - if (len < 0) - goto error_path; - - ctx = kmalloc(len, GFP_ATOMIC); - if (!ctx) - goto error_path; + return 0; - len = security_ipc_getsecurity(ipcp, ctx, len); - if (len < 0) - goto error_path; + ax = kmalloc(sizeof(*ax), GFP_ATOMIC); + if (!ax) + return -ENOMEM; - return ctx; + ax->uid = ipcp->uid; + ax->gid = ipcp->gid; + ax->mode = ipcp->mode; + selinux_get_ipc_sid(ipcp, &ax->osid); -error_path: - kfree(ctx); - audit_panic("error in audit_ipc_context"); -ret: - return NULL; + ax->d.type = AUDIT_IPC; + ax->d.next = context->aux; + context->aux = (void *)ax; + return 0; } /** - * audit_ipc_perms - record audit data for ipc + * audit_ipc_set_perm - record audit data for new ipc permissions * @qbytes: msgq bytes * @uid: msgq user id * @gid: msgq group id @@ -1196,7 +1207,7 @@ ret: * * Returns 0 for success or NULL context or < 0 on error. */ -int audit_ipc_perms(unsigned long qbytes, uid_t uid, gid_t gid, mode_t mode, struct kern_ipc_perm *ipcp) +int audit_ipc_set_perm(unsigned long qbytes, uid_t uid, gid_t gid, mode_t mode, struct kern_ipc_perm *ipcp) { struct audit_aux_data_ipcctl *ax; struct audit_context *context = current->audit_context; @@ -1212,9 +1223,9 @@ int audit_ipc_perms(unsigned long qbytes, uid_t uid, gid_t gid, mode_t mode, str ax->uid = uid; ax->gid = gid; ax->mode = mode; - ax->ctx = audit_ipc_context(ipcp); + selinux_get_ipc_sid(ipcp, &ax->osid); - ax->d.type = AUDIT_IPC; + ax->d.type = AUDIT_IPC_SET_PERM; ax->d.next = context->aux; context->aux = (void *)ax; return 0; diff --git a/kernel/exit.c b/kernel/exit.c index f86434d7b3d..e95b9328221 100644 --- a/kernel/exit.c +++ b/kernel/exit.c @@ -35,6 +35,7 @@ #include <linux/futex.h> #include <linux/compat.h> #include <linux/pipe_fs_i.h> +#include <linux/audit.h> /* for audit_free() */ #include <asm/uaccess.h> #include <asm/unistd.h> @@ -910,6 +911,8 @@ fastcall NORET_TYPE void do_exit(long code) if (unlikely(tsk->compat_robust_list)) compat_exit_robust_list(tsk); #endif + if (unlikely(tsk->audit_context)) + audit_free(tsk); exit_mm(tsk); exit_sem(tsk); diff --git a/kernel/fork.c b/kernel/fork.c index d2fa57d480d..ac8100e3088 100644 --- a/kernel/fork.c +++ b/kernel/fork.c @@ -114,8 +114,6 @@ void __put_task_struct(struct task_struct *tsk) WARN_ON(atomic_read(&tsk->usage)); WARN_ON(tsk == current); - if (unlikely(tsk->audit_context)) - audit_free(tsk); security_task_free(tsk); free_uid(tsk->user); put_group_info(tsk->group_info); diff --git a/kernel/irq/manage.c b/kernel/irq/manage.c index ac766ad573e..1279e349953 100644 --- a/kernel/irq/manage.c +++ b/kernel/irq/manage.c @@ -246,8 +246,10 @@ int setup_irq(unsigned int irq, struct irqaction * new) mismatch: spin_unlock_irqrestore(&desc->lock, flags); - printk(KERN_ERR "%s: irq handler mismatch\n", __FUNCTION__); - dump_stack(); + if (!(new->flags & SA_PROBEIRQ)) { + printk(KERN_ERR "%s: irq handler mismatch\n", __FUNCTION__); + dump_stack(); + } return -EBUSY; } diff --git a/kernel/power/main.c b/kernel/power/main.c index ee371f50cca..a6d9ef46009 100644 --- a/kernel/power/main.c +++ b/kernel/power/main.c @@ -272,7 +272,7 @@ static ssize_t state_store(struct subsystem * subsys, const char * buf, size_t n if (*s && !strncmp(buf, *s, len)) break; } - if (*s) + if (state < PM_SUSPEND_MAX && *s) error = enter_state(state); else error = -EINVAL; diff --git a/kernel/ptrace.c b/kernel/ptrace.c index 4e0f0ec003f..921c22ad16e 100644 --- a/kernel/ptrace.c +++ b/kernel/ptrace.c @@ -148,12 +148,34 @@ int ptrace_may_attach(struct task_struct *task) int ptrace_attach(struct task_struct *task) { int retval; - task_lock(task); + retval = -EPERM; if (task->pid <= 1) - goto bad; + goto out; if (task->tgid == current->tgid) - goto bad; + goto out; + +repeat: + /* + * Nasty, nasty. + * + * We want to hold both the task-lock and the + * tasklist_lock for writing at the same time. + * But that's against the rules (tasklist_lock + * is taken for reading by interrupts on other + * cpu's that may have task_lock). + */ + task_lock(task); + local_irq_disable(); + if (!write_trylock(&tasklist_lock)) { + local_irq_enable(); + task_unlock(task); + do { + cpu_relax(); + } while (!write_can_lock(&tasklist_lock)); + goto repeat; + } + /* the same process cannot be attached many times */ if (task->ptrace & PT_PTRACED) goto bad; @@ -166,17 +188,15 @@ int ptrace_attach(struct task_struct *task) ? PT_ATTACHED : 0); if (capable(CAP_SYS_PTRACE)) task->ptrace |= PT_PTRACE_CAP; - task_unlock(task); - write_lock_irq(&tasklist_lock); __ptrace_link(task, current); - write_unlock_irq(&tasklist_lock); force_sig_specific(SIGSTOP, task); - return 0; bad: + write_unlock_irq(&tasklist_lock); task_unlock(task); +out: return retval; } @@ -417,21 +437,22 @@ int ptrace_request(struct task_struct *child, long request, */ int ptrace_traceme(void) { - int ret; + int ret = -EPERM; /* * Are we already being traced? */ - if (current->ptrace & PT_PTRACED) - return -EPERM; - ret = security_ptrace(current->parent, current); - if (ret) - return -EPERM; - /* - * Set the ptrace bit in the process ptrace flags. - */ - current->ptrace |= PT_PTRACED; - return 0; + task_lock(current); + if (!(current->ptrace & PT_PTRACED)) { + ret = security_ptrace(current->parent, current); + /* + * Set the ptrace bit in the process ptrace flags. + */ + if (!ret) + current->ptrace |= PT_PTRACED; + } + task_unlock(current); + return ret; } /** diff --git a/lib/kobject.c b/lib/kobject.c index 01d95751394..b46350c2783 100644 --- a/lib/kobject.c +++ b/lib/kobject.c @@ -422,7 +422,6 @@ struct kobject *kobject_add_dir(struct kobject *parent, const char *name) return k; } -EXPORT_SYMBOL_GPL(kobject_add_dir); /** * kset_init - initialize a kset for use @@ -569,7 +568,7 @@ int subsys_create_file(struct subsystem * s, struct subsys_attribute * a) * @s: subsystem. * @a: attribute desciptor. */ - +#if 0 void subsys_remove_file(struct subsystem * s, struct subsys_attribute * a) { if (subsys_get(s)) { @@ -577,6 +576,7 @@ void subsys_remove_file(struct subsystem * s, struct subsys_attribute * a) subsys_put(s); } } +#endif /* 0 */ EXPORT_SYMBOL(kobject_init); EXPORT_SYMBOL(kobject_register); @@ -588,10 +588,7 @@ EXPORT_SYMBOL(kobject_del); EXPORT_SYMBOL(kset_register); EXPORT_SYMBOL(kset_unregister); -EXPORT_SYMBOL(kset_find_obj); -EXPORT_SYMBOL(subsystem_init); EXPORT_SYMBOL(subsystem_register); EXPORT_SYMBOL(subsystem_unregister); EXPORT_SYMBOL(subsys_create_file); -EXPORT_SYMBOL(subsys_remove_file); diff --git a/lib/kobject_uevent.c b/lib/kobject_uevent.c index 982226daf93..7f20e7b857c 100644 --- a/lib/kobject_uevent.c +++ b/lib/kobject_uevent.c @@ -25,11 +25,13 @@ #define BUFFER_SIZE 2048 /* buffer for the variables */ #define NUM_ENVP 32 /* number of env pointers */ -#if defined(CONFIG_HOTPLUG) && defined(CONFIG_NET) +#if defined(CONFIG_HOTPLUG) u64 uevent_seqnum; char uevent_helper[UEVENT_HELPER_PATH_LEN] = "/sbin/hotplug"; static DEFINE_SPINLOCK(sequence_lock); +#if defined(CONFIG_NET) static struct sock *uevent_sock; +#endif static char *action_to_string(enum kobject_action action) { @@ -155,6 +157,7 @@ void kobject_uevent(struct kobject *kobj, enum kobject_action action) spin_unlock(&sequence_lock); sprintf(seq_buff, "SEQNUM=%llu", (unsigned long long)seq); +#if defined(CONFIG_NET) /* send netlink message */ if (uevent_sock) { struct sk_buff *skb; @@ -179,6 +182,7 @@ void kobject_uevent(struct kobject *kobj, enum kobject_action action) netlink_broadcast(uevent_sock, skb, 0, 1, GFP_KERNEL); } } +#endif /* call uevent_helper, usually only enabled during early boot */ if (uevent_helper[0]) { @@ -249,6 +253,7 @@ int add_uevent_var(char **envp, int num_envp, int *cur_index, } EXPORT_SYMBOL_GPL(add_uevent_var); +#if defined(CONFIG_NET) static int __init kobject_uevent_init(void) { uevent_sock = netlink_kernel_create(NETLINK_KOBJECT_UEVENT, 1, NULL, @@ -264,5 +269,6 @@ static int __init kobject_uevent_init(void) } postcore_initcall(kobject_uevent_init); +#endif #endif /* CONFIG_HOTPLUG */ diff --git a/mm/filemap.c b/mm/filemap.c index 1120338a5d0..82c448898d0 100644 --- a/mm/filemap.c +++ b/mm/filemap.c @@ -697,6 +697,38 @@ unsigned find_get_pages(struct address_space *mapping, pgoff_t start, return ret; } +/** + * find_get_pages_contig - gang contiguous pagecache lookup + * @mapping: The address_space to search + * @index: The starting page index + * @nr_pages: The maximum number of pages + * @pages: Where the resulting pages are placed + * + * find_get_pages_contig() works exactly like find_get_pages(), except + * that the returned number of pages are guaranteed to be contiguous. + * + * find_get_pages_contig() returns the number of pages which were found. + */ +unsigned find_get_pages_contig(struct address_space *mapping, pgoff_t index, + unsigned int nr_pages, struct page **pages) +{ + unsigned int i; + unsigned int ret; + + read_lock_irq(&mapping->tree_lock); + ret = radix_tree_gang_lookup(&mapping->page_tree, + (void **)pages, index, nr_pages); + for (i = 0; i < ret; i++) { + if (pages[i]->mapping == NULL || pages[i]->index != index) + break; + + page_cache_get(pages[i]); + index++; + } + read_unlock_irq(&mapping->tree_lock); + return i; +} + /* * Like find_get_pages, except we only return pages which are tagged with * `tag'. We update *index to index the next page for the traversal. diff --git a/mm/memory_hotplug.c b/mm/memory_hotplug.c index 1fe76d963ac..1ae2b2cc3a5 100644 --- a/mm/memory_hotplug.c +++ b/mm/memory_hotplug.c @@ -69,12 +69,16 @@ int __add_pages(struct zone *zone, unsigned long phys_start_pfn, for (i = 0; i < nr_pages; i += PAGES_PER_SECTION) { err = __add_section(zone, phys_start_pfn + i); - if (err) + /* We want to keep adding the rest of the + * sections if the first ones already exist + */ + if (err && (err != -EEXIST)) break; } return err; } +EXPORT_SYMBOL_GPL(__add_pages); static void grow_zone_span(struct zone *zone, unsigned long start_pfn, unsigned long end_pfn) diff --git a/mm/migrate.c b/mm/migrate.c index d444229f259..1c25040693d 100644 --- a/mm/migrate.c +++ b/mm/migrate.c @@ -439,6 +439,17 @@ redo: goto unlock_both; } + /* Make sure the dirty bit is up to date */ + if (try_to_unmap(page, 1) == SWAP_FAIL) { + rc = -EPERM; + goto unlock_both; + } + + if (page_mapcount(page)) { + rc = -EAGAIN; + goto unlock_both; + } + /* * Default handling if a filesystem does not provide * a migration function. We can only migrate clean diff --git a/mm/slab.c b/mm/slab.c index af5c5237e11..c32af7e7581 100644 --- a/mm/slab.c +++ b/mm/slab.c @@ -979,7 +979,8 @@ static void __drain_alien_cache(struct kmem_cache *cachep, * That way we could avoid the overhead of putting the objects * into the free lists and getting them back later. */ - transfer_objects(rl3->shared, ac, ac->limit); + if (rl3->shared) + transfer_objects(rl3->shared, ac, ac->limit); free_block(cachep, ac->entry, ac->avail, node); ac->avail = 0; diff --git a/mm/sparse.c b/mm/sparse.c index 0a51f36ba3a..d7c32de99ee 100644 --- a/mm/sparse.c +++ b/mm/sparse.c @@ -32,7 +32,10 @@ static struct mem_section *sparse_index_alloc(int nid) unsigned long array_size = SECTIONS_PER_ROOT * sizeof(struct mem_section); - section = alloc_bootmem_node(NODE_DATA(nid), array_size); + if (system_state == SYSTEM_RUNNING) + section = kmalloc_node(array_size, GFP_KERNEL, nid); + else + section = alloc_bootmem_node(NODE_DATA(nid), array_size); if (section) memset(section, 0, array_size); @@ -281,9 +284,9 @@ int sparse_add_one_section(struct zone *zone, unsigned long start_pfn, ret = sparse_init_one_section(ms, section_nr, memmap); - if (ret <= 0) - __kfree_section_memmap(memmap, nr_pages); out: pgdat_resize_unlock(pgdat, &flags); + if (ret <= 0) + __kfree_section_memmap(memmap, nr_pages); return ret; } diff --git a/net/ax25/af_ax25.c b/net/ax25/af_ax25.c index dbf9b47681f..a2e0dd047e9 100644 --- a/net/ax25/af_ax25.c +++ b/net/ax25/af_ax25.c @@ -228,6 +228,8 @@ ax25_cb *ax25_find_cb(ax25_address *src_addr, ax25_address *dest_addr, return NULL; } +EXPORT_SYMBOL(ax25_find_cb); + void ax25_send_to_raw(ax25_address *addr, struct sk_buff *skb, int proto) { ax25_cb *s; @@ -424,6 +426,26 @@ static int ax25_ctl_ioctl(const unsigned int cmd, void __user *arg) return 0; } +static void ax25_fillin_cb_from_dev(ax25_cb *ax25, ax25_dev *ax25_dev) +{ + ax25->rtt = msecs_to_jiffies(ax25_dev->values[AX25_VALUES_T1]) / 2; + ax25->t1 = msecs_to_jiffies(ax25_dev->values[AX25_VALUES_T1]); + ax25->t2 = msecs_to_jiffies(ax25_dev->values[AX25_VALUES_T2]); + ax25->t3 = msecs_to_jiffies(ax25_dev->values[AX25_VALUES_T3]); + ax25->n2 = ax25_dev->values[AX25_VALUES_N2]; + ax25->paclen = ax25_dev->values[AX25_VALUES_PACLEN]; + ax25->idle = msecs_to_jiffies(ax25_dev->values[AX25_VALUES_IDLE]); + ax25->backoff = ax25_dev->values[AX25_VALUES_BACKOFF]; + + if (ax25_dev->values[AX25_VALUES_AXDEFMODE]) { + ax25->modulus = AX25_EMODULUS; + ax25->window = ax25_dev->values[AX25_VALUES_EWINDOW]; + } else { + ax25->modulus = AX25_MODULUS; + ax25->window = ax25_dev->values[AX25_VALUES_WINDOW]; + } +} + /* * Fill in a created AX.25 created control block with the default * values for a particular device. @@ -433,39 +455,28 @@ void ax25_fillin_cb(ax25_cb *ax25, ax25_dev *ax25_dev) ax25->ax25_dev = ax25_dev; if (ax25->ax25_dev != NULL) { - ax25->rtt = ax25_dev->values[AX25_VALUES_T1] / 2; - ax25->t1 = ax25_dev->values[AX25_VALUES_T1]; - ax25->t2 = ax25_dev->values[AX25_VALUES_T2]; - ax25->t3 = ax25_dev->values[AX25_VALUES_T3]; - ax25->n2 = ax25_dev->values[AX25_VALUES_N2]; - ax25->paclen = ax25_dev->values[AX25_VALUES_PACLEN]; - ax25->idle = ax25_dev->values[AX25_VALUES_IDLE]; - ax25->backoff = ax25_dev->values[AX25_VALUES_BACKOFF]; - - if (ax25_dev->values[AX25_VALUES_AXDEFMODE]) { - ax25->modulus = AX25_EMODULUS; - ax25->window = ax25_dev->values[AX25_VALUES_EWINDOW]; - } else { - ax25->modulus = AX25_MODULUS; - ax25->window = ax25_dev->values[AX25_VALUES_WINDOW]; - } + ax25_fillin_cb_from_dev(ax25, ax25_dev); + return; + } + + /* + * No device, use kernel / AX.25 spec default values + */ + ax25->rtt = msecs_to_jiffies(AX25_DEF_T1) / 2; + ax25->t1 = msecs_to_jiffies(AX25_DEF_T1); + ax25->t2 = msecs_to_jiffies(AX25_DEF_T2); + ax25->t3 = msecs_to_jiffies(AX25_DEF_T3); + ax25->n2 = AX25_DEF_N2; + ax25->paclen = AX25_DEF_PACLEN; + ax25->idle = msecs_to_jiffies(AX25_DEF_IDLE); + ax25->backoff = AX25_DEF_BACKOFF; + + if (AX25_DEF_AXDEFMODE) { + ax25->modulus = AX25_EMODULUS; + ax25->window = AX25_DEF_EWINDOW; } else { - ax25->rtt = AX25_DEF_T1 / 2; - ax25->t1 = AX25_DEF_T1; - ax25->t2 = AX25_DEF_T2; - ax25->t3 = AX25_DEF_T3; - ax25->n2 = AX25_DEF_N2; - ax25->paclen = AX25_DEF_PACLEN; - ax25->idle = AX25_DEF_IDLE; - ax25->backoff = AX25_DEF_BACKOFF; - - if (AX25_DEF_AXDEFMODE) { - ax25->modulus = AX25_EMODULUS; - ax25->window = AX25_DEF_EWINDOW; - } else { - ax25->modulus = AX25_MODULUS; - ax25->window = AX25_DEF_WINDOW; - } + ax25->modulus = AX25_MODULUS; + ax25->window = AX25_DEF_WINDOW; } } @@ -1979,24 +1990,6 @@ static struct notifier_block ax25_dev_notifier = { .notifier_call =ax25_device_event, }; -EXPORT_SYMBOL(ax25_hard_header); -EXPORT_SYMBOL(ax25_rebuild_header); -EXPORT_SYMBOL(ax25_findbyuid); -EXPORT_SYMBOL(ax25_find_cb); -EXPORT_SYMBOL(ax25_linkfail_register); -EXPORT_SYMBOL(ax25_linkfail_release); -EXPORT_SYMBOL(ax25_listen_register); -EXPORT_SYMBOL(ax25_listen_release); -EXPORT_SYMBOL(ax25_protocol_register); -EXPORT_SYMBOL(ax25_protocol_release); -EXPORT_SYMBOL(ax25_send_frame); -EXPORT_SYMBOL(ax25_uid_policy); -EXPORT_SYMBOL(ax25cmp); -EXPORT_SYMBOL(ax2asc); -EXPORT_SYMBOL(asc2ax); -EXPORT_SYMBOL(null_ax25_address); -EXPORT_SYMBOL(ax25_display_timer); - static int __init ax25_init(void) { int rc = proto_register(&ax25_proto, 0); diff --git a/net/ax25/ax25_addr.c b/net/ax25/ax25_addr.c index 0164a155b8c..5f0896ad004 100644 --- a/net/ax25/ax25_addr.c +++ b/net/ax25/ax25_addr.c @@ -11,6 +11,7 @@ #include <linux/socket.h> #include <linux/in.h> #include <linux/kernel.h> +#include <linux/module.h> #include <linux/sched.h> #include <linux/timer.h> #include <linux/string.h> @@ -33,6 +34,8 @@ */ ax25_address null_ax25_address = {{0x40, 0x40, 0x40, 0x40, 0x40, 0x40, 0x00}}; +EXPORT_SYMBOL(null_ax25_address); + /* * ax25 -> ascii conversion */ @@ -64,6 +67,8 @@ char *ax2asc(char *buf, ax25_address *a) } +EXPORT_SYMBOL(ax2asc); + /* * ascii -> ax25 conversion */ @@ -97,6 +102,8 @@ void asc2ax(ax25_address *addr, char *callsign) addr->ax25_call[6] &= 0x1E; } +EXPORT_SYMBOL(asc2ax); + /* * Compare two ax.25 addresses */ @@ -116,6 +123,8 @@ int ax25cmp(ax25_address *a, ax25_address *b) return 2; /* Partial match */ } +EXPORT_SYMBOL(ax25cmp); + /* * Compare two AX.25 digipeater paths. */ diff --git a/net/ax25/ax25_ds_timer.c b/net/ax25/ax25_ds_timer.c index 061083efc1d..5961459935e 100644 --- a/net/ax25/ax25_ds_timer.c +++ b/net/ax25/ax25_ds_timer.c @@ -61,7 +61,8 @@ void ax25_ds_set_timer(ax25_dev *ax25_dev) return; del_timer(&ax25_dev->dama.slave_timer); - ax25_dev->dama.slave_timeout = ax25_dev->values[AX25_VALUES_DS_TIMEOUT] / 10; + ax25_dev->dama.slave_timeout = + msecs_to_jiffies(ax25_dev->values[AX25_VALUES_DS_TIMEOUT]) / 10; ax25_ds_add_timer(ax25_dev); } diff --git a/net/ax25/ax25_iface.c b/net/ax25/ax25_iface.c index d68aff10072..3bb152710b7 100644 --- a/net/ax25/ax25_iface.c +++ b/net/ax25/ax25_iface.c @@ -12,6 +12,7 @@ #include <linux/socket.h> #include <linux/in.h> #include <linux/kernel.h> +#include <linux/module.h> #include <linux/sched.h> #include <linux/spinlock.h> #include <linux/timer.h> @@ -74,6 +75,8 @@ int ax25_protocol_register(unsigned int pid, return 1; } +EXPORT_SYMBOL(ax25_protocol_register); + void ax25_protocol_release(unsigned int pid) { struct protocol_struct *s, *protocol; @@ -106,6 +109,8 @@ void ax25_protocol_release(unsigned int pid) write_unlock(&protocol_list_lock); } +EXPORT_SYMBOL(ax25_protocol_release); + int ax25_linkfail_register(void (*func)(ax25_cb *, int)) { struct linkfail_struct *linkfail; @@ -123,6 +128,8 @@ int ax25_linkfail_register(void (*func)(ax25_cb *, int)) return 1; } +EXPORT_SYMBOL(ax25_linkfail_register); + void ax25_linkfail_release(void (*func)(ax25_cb *, int)) { struct linkfail_struct *s, *linkfail; @@ -155,6 +162,8 @@ void ax25_linkfail_release(void (*func)(ax25_cb *, int)) spin_unlock_bh(&linkfail_lock); } +EXPORT_SYMBOL(ax25_linkfail_release); + int ax25_listen_register(ax25_address *callsign, struct net_device *dev) { struct listen_struct *listen; @@ -176,6 +185,8 @@ int ax25_listen_register(ax25_address *callsign, struct net_device *dev) return 1; } +EXPORT_SYMBOL(ax25_listen_register); + void ax25_listen_release(ax25_address *callsign, struct net_device *dev) { struct listen_struct *s, *listen; @@ -208,6 +219,8 @@ void ax25_listen_release(ax25_address *callsign, struct net_device *dev) spin_unlock_bh(&listen_lock); } +EXPORT_SYMBOL(ax25_listen_release); + int (*ax25_protocol_function(unsigned int pid))(struct sk_buff *, ax25_cb *) { int (*res)(struct sk_buff *, ax25_cb *) = NULL; diff --git a/net/ax25/ax25_ip.c b/net/ax25/ax25_ip.c index d643dac3ecc..a0b534f80f1 100644 --- a/net/ax25/ax25_ip.c +++ b/net/ax25/ax25_ip.c @@ -12,6 +12,7 @@ #include <linux/socket.h> #include <linux/in.h> #include <linux/kernel.h> +#include <linux/module.h> #include <linux/sched.h> #include <linux/timer.h> #include <linux/string.h> @@ -221,3 +222,5 @@ int ax25_rebuild_header(struct sk_buff *skb) #endif +EXPORT_SYMBOL(ax25_hard_header); +EXPORT_SYMBOL(ax25_rebuild_header); diff --git a/net/ax25/ax25_out.c b/net/ax25/ax25_out.c index 5fc048dcd39..5d99852b239 100644 --- a/net/ax25/ax25_out.c +++ b/net/ax25/ax25_out.c @@ -14,6 +14,7 @@ #include <linux/socket.h> #include <linux/in.h> #include <linux/kernel.h> +#include <linux/module.h> #include <linux/sched.h> #include <linux/timer.h> #include <linux/string.h> @@ -104,6 +105,8 @@ ax25_cb *ax25_send_frame(struct sk_buff *skb, int paclen, ax25_address *src, ax2 return ax25; /* We had to create it */ } +EXPORT_SYMBOL(ax25_send_frame); + /* * All outgoing AX.25 I frames pass via this routine. Therefore this is * where the fragmentation of frames takes place. If fragment is set to diff --git a/net/ax25/ax25_route.c b/net/ax25/ax25_route.c index f04f8630fd2..5ac98250797 100644 --- a/net/ax25/ax25_route.c +++ b/net/ax25/ax25_route.c @@ -360,7 +360,7 @@ struct file_operations ax25_route_fops = { /* * Find AX.25 route * - * Only routes with a refernce rout of zero can be destroyed. + * Only routes with a reference count of zero can be destroyed. */ static ax25_route *ax25_get_route(ax25_address *addr, struct net_device *dev) { diff --git a/net/ax25/ax25_timer.c b/net/ax25/ax25_timer.c index 7a6b50a1455..ec254057f21 100644 --- a/net/ax25/ax25_timer.c +++ b/net/ax25/ax25_timer.c @@ -18,6 +18,7 @@ #include <linux/socket.h> #include <linux/in.h> #include <linux/kernel.h> +#include <linux/module.h> #include <linux/jiffies.h> #include <linux/timer.h> #include <linux/string.h> @@ -137,6 +138,8 @@ unsigned long ax25_display_timer(struct timer_list *timer) return timer->expires - jiffies; } +EXPORT_SYMBOL(ax25_display_timer); + static void ax25_heartbeat_expiry(unsigned long param) { int proto = AX25_PROTO_STD_SIMPLEX; diff --git a/net/ax25/ax25_uid.c b/net/ax25/ax25_uid.c index b8b5854bce9..5e9a81e8b21 100644 --- a/net/ax25/ax25_uid.c +++ b/net/ax25/ax25_uid.c @@ -49,6 +49,8 @@ static DEFINE_RWLOCK(ax25_uid_lock); int ax25_uid_policy = 0; +EXPORT_SYMBOL(ax25_uid_policy); + ax25_uid_assoc *ax25_findbyuid(uid_t uid) { ax25_uid_assoc *ax25_uid, *res = NULL; @@ -67,6 +69,8 @@ ax25_uid_assoc *ax25_findbyuid(uid_t uid) return res; } +EXPORT_SYMBOL(ax25_findbyuid); + int ax25_uid_ioctl(int cmd, struct sockaddr_ax25 *sax) { ax25_uid_assoc *ax25_uid; diff --git a/net/ax25/sysctl_net_ax25.c b/net/ax25/sysctl_net_ax25.c index 894a22558d9..bdb64c36df1 100644 --- a/net/ax25/sysctl_net_ax25.c +++ b/net/ax25/sysctl_net_ax25.c @@ -18,14 +18,14 @@ static int min_backoff[1], max_backoff[] = {2}; static int min_conmode[1], max_conmode[] = {2}; static int min_window[] = {1}, max_window[] = {7}; static int min_ewindow[] = {1}, max_ewindow[] = {63}; -static int min_t1[] = {1}, max_t1[] = {30 * HZ}; -static int min_t2[] = {1}, max_t2[] = {20 * HZ}; -static int min_t3[1], max_t3[] = {3600 * HZ}; -static int min_idle[1], max_idle[] = {65535 * HZ}; +static int min_t1[] = {1}, max_t1[] = {30000}; +static int min_t2[] = {1}, max_t2[] = {20000}; +static int min_t3[1], max_t3[] = {3600000}; +static int min_idle[1], max_idle[] = {65535000}; static int min_n2[] = {1}, max_n2[] = {31}; static int min_paclen[] = {1}, max_paclen[] = {512}; static int min_proto[1], max_proto[] = { AX25_PROTO_MAX }; -static int min_ds_timeout[1], max_ds_timeout[] = {65535 * HZ}; +static int min_ds_timeout[1], max_ds_timeout[] = {65535000}; static struct ctl_table_header *ax25_table_header; diff --git a/net/bridge/br_if.c b/net/bridge/br_if.c index 59eef42d4a4..ad1c7af65ec 100644 --- a/net/bridge/br_if.c +++ b/net/bridge/br_if.c @@ -308,26 +308,19 @@ int br_add_bridge(const char *name) if (ret) goto err2; - /* network device kobject is not setup until - * after rtnl_unlock does it's hotplug magic. - * so hold reference to avoid race. - */ - dev_hold(dev); - rtnl_unlock(); - ret = br_sysfs_addbr(dev); - dev_put(dev); - - if (ret) - unregister_netdev(dev); - out: - return ret; + if (ret) + goto err3; + rtnl_unlock(); + return 0; + err3: + unregister_netdev(dev); err2: free_netdev(dev); err1: rtnl_unlock(); - goto out; + return ret; } int br_del_bridge(const char *name) diff --git a/net/bridge/br_input.c b/net/bridge/br_input.c index b0b7f55c1ed..bfa4d8c333f 100644 --- a/net/bridge/br_input.c +++ b/net/bridge/br_input.c @@ -66,6 +66,7 @@ int br_handle_frame_finish(struct sk_buff *skb) } if (is_multicast_ether_addr(dest)) { + br->statistics.multicast++; br_flood_forward(br, skb, !passedup); if (!passedup) br_pass_frame_up(br, skb); diff --git a/net/core/dev.c b/net/core/dev.c index 3bad1afc89f..2dce673a039 100644 --- a/net/core/dev.c +++ b/net/core/dev.c @@ -193,7 +193,7 @@ static inline struct hlist_head *dev_index_hash(int ifindex) * Our notifier list */ -static BLOCKING_NOTIFIER_HEAD(netdev_chain); +static RAW_NOTIFIER_HEAD(netdev_chain); /* * Device drivers call our routines to queue packets here. We empty the @@ -736,7 +736,7 @@ int dev_change_name(struct net_device *dev, char *newname) if (!err) { hlist_del(&dev->name_hlist); hlist_add_head(&dev->name_hlist, dev_name_hash(dev->name)); - blocking_notifier_call_chain(&netdev_chain, + raw_notifier_call_chain(&netdev_chain, NETDEV_CHANGENAME, dev); } @@ -751,7 +751,7 @@ int dev_change_name(struct net_device *dev, char *newname) */ void netdev_features_change(struct net_device *dev) { - blocking_notifier_call_chain(&netdev_chain, NETDEV_FEAT_CHANGE, dev); + raw_notifier_call_chain(&netdev_chain, NETDEV_FEAT_CHANGE, dev); } EXPORT_SYMBOL(netdev_features_change); @@ -766,7 +766,7 @@ EXPORT_SYMBOL(netdev_features_change); void netdev_state_change(struct net_device *dev) { if (dev->flags & IFF_UP) { - blocking_notifier_call_chain(&netdev_chain, + raw_notifier_call_chain(&netdev_chain, NETDEV_CHANGE, dev); rtmsg_ifinfo(RTM_NEWLINK, dev, 0); } @@ -864,7 +864,7 @@ int dev_open(struct net_device *dev) /* * ... and announce new interface. */ - blocking_notifier_call_chain(&netdev_chain, NETDEV_UP, dev); + raw_notifier_call_chain(&netdev_chain, NETDEV_UP, dev); } return ret; } @@ -887,7 +887,7 @@ int dev_close(struct net_device *dev) * Tell people we are going down, so that they can * prepare to death, when device is still operating. */ - blocking_notifier_call_chain(&netdev_chain, NETDEV_GOING_DOWN, dev); + raw_notifier_call_chain(&netdev_chain, NETDEV_GOING_DOWN, dev); dev_deactivate(dev); @@ -924,7 +924,7 @@ int dev_close(struct net_device *dev) /* * Tell people we are down */ - blocking_notifier_call_chain(&netdev_chain, NETDEV_DOWN, dev); + raw_notifier_call_chain(&netdev_chain, NETDEV_DOWN, dev); return 0; } @@ -955,7 +955,7 @@ int register_netdevice_notifier(struct notifier_block *nb) int err; rtnl_lock(); - err = blocking_notifier_chain_register(&netdev_chain, nb); + err = raw_notifier_chain_register(&netdev_chain, nb); if (!err) { for (dev = dev_base; dev; dev = dev->next) { nb->notifier_call(nb, NETDEV_REGISTER, dev); @@ -983,7 +983,7 @@ int unregister_netdevice_notifier(struct notifier_block *nb) int err; rtnl_lock(); - err = blocking_notifier_chain_unregister(&netdev_chain, nb); + err = raw_notifier_chain_unregister(&netdev_chain, nb); rtnl_unlock(); return err; } @@ -994,12 +994,12 @@ int unregister_netdevice_notifier(struct notifier_block *nb) * @v: pointer passed unmodified to notifier function * * Call all network notifier blocks. Parameters and return value - * are as for blocking_notifier_call_chain(). + * are as for raw_notifier_call_chain(). */ int call_netdevice_notifiers(unsigned long val, void *v) { - return blocking_notifier_call_chain(&netdev_chain, val, v); + return raw_notifier_call_chain(&netdev_chain, val, v); } /* When > 0 there are consumers of rx skb time stamps */ @@ -2308,7 +2308,7 @@ int dev_change_flags(struct net_device *dev, unsigned flags) if (dev->flags & IFF_UP && ((old_flags ^ dev->flags) &~ (IFF_UP | IFF_PROMISC | IFF_ALLMULTI | IFF_VOLATILE))) - blocking_notifier_call_chain(&netdev_chain, + raw_notifier_call_chain(&netdev_chain, NETDEV_CHANGE, dev); if ((flags ^ dev->gflags) & IFF_PROMISC) { @@ -2353,7 +2353,7 @@ int dev_set_mtu(struct net_device *dev, int new_mtu) else dev->mtu = new_mtu; if (!err && dev->flags & IFF_UP) - blocking_notifier_call_chain(&netdev_chain, + raw_notifier_call_chain(&netdev_chain, NETDEV_CHANGEMTU, dev); return err; } @@ -2370,7 +2370,7 @@ int dev_set_mac_address(struct net_device *dev, struct sockaddr *sa) return -ENODEV; err = dev->set_mac_address(dev, sa); if (!err) - blocking_notifier_call_chain(&netdev_chain, + raw_notifier_call_chain(&netdev_chain, NETDEV_CHANGEADDR, dev); return err; } @@ -2427,7 +2427,7 @@ static int dev_ifsioc(struct ifreq *ifr, unsigned int cmd) return -EINVAL; memcpy(dev->broadcast, ifr->ifr_hwaddr.sa_data, min(sizeof ifr->ifr_hwaddr.sa_data, (size_t) dev->addr_len)); - blocking_notifier_call_chain(&netdev_chain, + raw_notifier_call_chain(&netdev_chain, NETDEV_CHANGEADDR, dev); return 0; @@ -2777,6 +2777,8 @@ int register_netdevice(struct net_device *dev) BUG_ON(dev_boot_phase); ASSERT_RTNL(); + might_sleep(); + /* When net_device's are persistent, this will be fatal. */ BUG_ON(dev->reg_state != NETREG_UNINITIALIZED); @@ -2863,6 +2865,11 @@ int register_netdevice(struct net_device *dev) if (!dev->rebuild_header) dev->rebuild_header = default_rebuild_header; + ret = netdev_register_sysfs(dev); + if (ret) + goto out_err; + dev->reg_state = NETREG_REGISTERED; + /* * Default initial state at registry is that the * device is present. @@ -2878,14 +2885,11 @@ int register_netdevice(struct net_device *dev) hlist_add_head(&dev->name_hlist, head); hlist_add_head(&dev->index_hlist, dev_index_hash(dev->ifindex)); dev_hold(dev); - dev->reg_state = NETREG_REGISTERING; write_unlock_bh(&dev_base_lock); /* Notify protocols, that a new device appeared. */ - blocking_notifier_call_chain(&netdev_chain, NETDEV_REGISTER, dev); + raw_notifier_call_chain(&netdev_chain, NETDEV_REGISTER, dev); - /* Finish registration after unlock */ - net_set_todo(dev); ret = 0; out: @@ -2961,7 +2965,7 @@ static void netdev_wait_allrefs(struct net_device *dev) rtnl_lock(); /* Rebroadcast unregister notification */ - blocking_notifier_call_chain(&netdev_chain, + raw_notifier_call_chain(&netdev_chain, NETDEV_UNREGISTER, dev); if (test_bit(__LINK_STATE_LINKWATCH_PENDING, @@ -3008,7 +3012,7 @@ static void netdev_wait_allrefs(struct net_device *dev) * * We are invoked by rtnl_unlock() after it drops the semaphore. * This allows us to deal with problems: - * 1) We can create/delete sysfs objects which invoke hotplug + * 1) We can delete sysfs objects which invoke hotplug * without deadlocking with linkwatch via keventd. * 2) Since we run with the RTNL semaphore not held, we can sleep * safely in order to wait for the netdev refcnt to drop to zero. @@ -3017,8 +3021,6 @@ static DEFINE_MUTEX(net_todo_run_mutex); void netdev_run_todo(void) { struct list_head list = LIST_HEAD_INIT(list); - int err; - /* Need to guard against multiple cpu's getting out of order. */ mutex_lock(&net_todo_run_mutex); @@ -3041,40 +3043,29 @@ void netdev_run_todo(void) = list_entry(list.next, struct net_device, todo_list); list_del(&dev->todo_list); - switch(dev->reg_state) { - case NETREG_REGISTERING: - dev->reg_state = NETREG_REGISTERED; - err = netdev_register_sysfs(dev); - if (err) - printk(KERN_ERR "%s: failed sysfs registration (%d)\n", - dev->name, err); - break; - - case NETREG_UNREGISTERING: - netdev_unregister_sysfs(dev); - dev->reg_state = NETREG_UNREGISTERED; - - netdev_wait_allrefs(dev); + if (unlikely(dev->reg_state != NETREG_UNREGISTERING)) { + printk(KERN_ERR "network todo '%s' but state %d\n", + dev->name, dev->reg_state); + dump_stack(); + continue; + } - /* paranoia */ - BUG_ON(atomic_read(&dev->refcnt)); - BUG_TRAP(!dev->ip_ptr); - BUG_TRAP(!dev->ip6_ptr); - BUG_TRAP(!dev->dn_ptr); + netdev_unregister_sysfs(dev); + dev->reg_state = NETREG_UNREGISTERED; + netdev_wait_allrefs(dev); - /* It must be the very last action, - * after this 'dev' may point to freed up memory. - */ - if (dev->destructor) - dev->destructor(dev); - break; + /* paranoia */ + BUG_ON(atomic_read(&dev->refcnt)); + BUG_TRAP(!dev->ip_ptr); + BUG_TRAP(!dev->ip6_ptr); + BUG_TRAP(!dev->dn_ptr); - default: - printk(KERN_ERR "network todo '%s' but state %d\n", - dev->name, dev->reg_state); - break; - } + /* It must be the very last action, + * after this 'dev' may point to freed up memory. + */ + if (dev->destructor) + dev->destructor(dev); } out: @@ -3216,7 +3207,7 @@ int unregister_netdevice(struct net_device *dev) /* Notify protocols, that we are about to destroy this device. They should clean all the things. */ - blocking_notifier_call_chain(&netdev_chain, NETDEV_UNREGISTER, dev); + raw_notifier_call_chain(&netdev_chain, NETDEV_UNREGISTER, dev); /* * Flush the multicast chain diff --git a/net/core/link_watch.c b/net/core/link_watch.c index 341de44c7ed..646937cc2d8 100644 --- a/net/core/link_watch.c +++ b/net/core/link_watch.c @@ -170,13 +170,13 @@ void linkwatch_fire_event(struct net_device *dev) spin_unlock_irqrestore(&lweventlist_lock, flags); if (!test_and_set_bit(LW_RUNNING, &linkwatch_flags)) { - unsigned long thisevent = jiffies; + unsigned long delay = linkwatch_nextevent - jiffies; - if (thisevent >= linkwatch_nextevent) { + /* If we wrap around we'll delay it by at most HZ. */ + if (!delay || delay > HZ) schedule_work(&linkwatch_work); - } else { - schedule_delayed_work(&linkwatch_work, linkwatch_nextevent - thisevent); - } + else + schedule_delayed_work(&linkwatch_work, delay); } } } diff --git a/net/core/net-sysfs.c b/net/core/net-sysfs.c index c12990c9c60..47a6fceb677 100644 --- a/net/core/net-sysfs.c +++ b/net/core/net-sysfs.c @@ -29,7 +29,7 @@ static const char fmt_ulong[] = "%lu\n"; static inline int dev_isalive(const struct net_device *dev) { - return dev->reg_state == NETREG_REGISTERED; + return dev->reg_state <= NETREG_REGISTERED; } /* use same locking rules as GIF* ioctl's */ @@ -445,58 +445,33 @@ static struct class net_class = { void netdev_unregister_sysfs(struct net_device * net) { - struct class_device * class_dev = &(net->class_dev); - - if (net->get_stats) - sysfs_remove_group(&class_dev->kobj, &netstat_group); - -#ifdef WIRELESS_EXT - if (net->get_wireless_stats || (net->wireless_handlers && - net->wireless_handlers->get_wireless_stats)) - sysfs_remove_group(&class_dev->kobj, &wireless_group); -#endif - class_device_del(class_dev); - + class_device_del(&(net->class_dev)); } /* Create sysfs entries for network device. */ int netdev_register_sysfs(struct net_device *net) { struct class_device *class_dev = &(net->class_dev); - int ret; + struct attribute_group **groups = net->sysfs_groups; + class_device_initialize(class_dev); class_dev->class = &net_class; class_dev->class_data = net; + class_dev->groups = groups; + BUILD_BUG_ON(BUS_ID_SIZE < IFNAMSIZ); strlcpy(class_dev->class_id, net->name, BUS_ID_SIZE); - if ((ret = class_device_register(class_dev))) - goto out; - if (net->get_stats && - (ret = sysfs_create_group(&class_dev->kobj, &netstat_group))) - goto out_unreg; + if (net->get_stats) + *groups++ = &netstat_group; #ifdef WIRELESS_EXT - if (net->get_wireless_stats || (net->wireless_handlers && - net->wireless_handlers->get_wireless_stats)) { - ret = sysfs_create_group(&class_dev->kobj, &wireless_group); - if (ret) - goto out_cleanup; - } - return 0; -out_cleanup: - if (net->get_stats) - sysfs_remove_group(&class_dev->kobj, &netstat_group); -#else - return 0; + if (net->get_wireless_stats + || (net->wireless_handlers && net->wireless_handlers->get_wireless_stats)) + *groups++ = &wireless_group; #endif -out_unreg: - printk(KERN_WARNING "%s: sysfs attribute registration failed %d\n", - net->name, ret); - class_device_unregister(class_dev); -out: - return ret; + return class_device_add(class_dev); } int netdev_sysfs_init(void) diff --git a/net/dccp/proto.c b/net/dccp/proto.c index 1ff7328b0e1..2e0ee8355c4 100644 --- a/net/dccp/proto.c +++ b/net/dccp/proto.c @@ -848,6 +848,7 @@ static int dccp_close_state(struct sock *sk) void dccp_close(struct sock *sk, long timeout) { struct sk_buff *skb; + int state; lock_sock(sk); @@ -882,6 +883,11 @@ void dccp_close(struct sock *sk, long timeout) sk_stream_wait_close(sk, timeout); adjudge_to_death: + state = sk->sk_state; + sock_hold(sk); + sock_orphan(sk); + atomic_inc(sk->sk_prot->orphan_count); + /* * It is the last release_sock in its life. It will remove backlog. */ @@ -894,8 +900,9 @@ adjudge_to_death: bh_lock_sock(sk); BUG_TRAP(!sock_owned_by_user(sk)); - sock_hold(sk); - sock_orphan(sk); + /* Have we already been destroyed by a softirq or backlog? */ + if (state != DCCP_CLOSED && sk->sk_state == DCCP_CLOSED) + goto out; /* * The last release_sock may have processed the CLOSE or RESET @@ -915,12 +922,12 @@ adjudge_to_death: #endif } - atomic_inc(sk->sk_prot->orphan_count); if (sk->sk_state == DCCP_CLOSED) inet_csk_destroy_sock(sk); /* Otherwise, socket is reprieved until protocol close. */ +out: bh_unlock_sock(sk); local_bh_enable(); sock_put(sk); diff --git a/net/decnet/dn_neigh.c b/net/decnet/dn_neigh.c index 7c8692c26bf..66e230c3b32 100644 --- a/net/decnet/dn_neigh.c +++ b/net/decnet/dn_neigh.c @@ -493,7 +493,6 @@ struct elist_cb_state { static void neigh_elist_cb(struct neighbour *neigh, void *_info) { struct elist_cb_state *s = _info; - struct dn_dev *dn_db; struct dn_neigh *dn; if (neigh->dev != s->dev) @@ -503,10 +502,6 @@ static void neigh_elist_cb(struct neighbour *neigh, void *_info) if (!(dn->flags & (DN_NDFLAG_R1|DN_NDFLAG_R2))) return; - dn_db = (struct dn_dev *) s->dev->dn_ptr; - if (dn_db->parms.forwarding == 1 && (dn->flags & DN_NDFLAG_R2)) - return; - if (s->t == s->n) s->rs = dn_find_slot(s->ptr, s->n, dn->priority); else diff --git a/net/ieee80211/softmac/ieee80211softmac_assoc.c b/net/ieee80211/softmac/ieee80211softmac_assoc.c index fb79ce7d643..57ea9f6f465 100644 --- a/net/ieee80211/softmac/ieee80211softmac_assoc.c +++ b/net/ieee80211/softmac/ieee80211softmac_assoc.c @@ -51,11 +51,12 @@ ieee80211softmac_assoc(struct ieee80211softmac_device *mac, struct ieee80211soft spin_lock_irqsave(&mac->lock, flags); mac->associnfo.associating = 1; mac->associated = 0; /* just to make sure */ - spin_unlock_irqrestore(&mac->lock, flags); /* Set a timer for timeout */ /* FIXME: make timeout configurable */ - schedule_delayed_work(&mac->associnfo.timeout, 5 * HZ); + if (likely(mac->running)) + schedule_delayed_work(&mac->associnfo.timeout, 5 * HZ); + spin_unlock_irqrestore(&mac->lock, flags); } void @@ -319,6 +320,9 @@ ieee80211softmac_handle_assoc_response(struct net_device * dev, u16 status = le16_to_cpup(&resp->status); struct ieee80211softmac_network *network = NULL; unsigned long flags; + + if (unlikely(!mac->running)) + return -ENODEV; spin_lock_irqsave(&mac->lock, flags); @@ -377,10 +381,16 @@ ieee80211softmac_handle_disassoc(struct net_device * dev, { struct ieee80211softmac_device *mac = ieee80211_priv(dev); unsigned long flags; + + if (unlikely(!mac->running)) + return -ENODEV; + if (memcmp(disassoc->header.addr2, mac->associnfo.bssid, ETH_ALEN)) return 0; + if (memcmp(disassoc->header.addr1, mac->dev->dev_addr, ETH_ALEN)) return 0; + dprintk(KERN_INFO PFX "got disassoc frame\n"); netif_carrier_off(dev); spin_lock_irqsave(&mac->lock, flags); @@ -400,6 +410,9 @@ ieee80211softmac_handle_reassoc_req(struct net_device * dev, struct ieee80211softmac_device *mac = ieee80211_priv(dev); struct ieee80211softmac_network *network; + if (unlikely(!mac->running)) + return -ENODEV; + network = ieee80211softmac_get_network_by_bssid(mac, resp->header.addr3); if (!network) { dprintkl(KERN_INFO PFX "reassoc request from unknown network\n"); diff --git a/net/ieee80211/softmac/ieee80211softmac_auth.c b/net/ieee80211/softmac/ieee80211softmac_auth.c index 9a0eac6c61e..06e33262466 100644 --- a/net/ieee80211/softmac/ieee80211softmac_auth.c +++ b/net/ieee80211/softmac/ieee80211softmac_auth.c @@ -86,6 +86,11 @@ ieee80211softmac_auth_queue(void *data) /* Lock and set flags */ spin_lock_irqsave(&mac->lock, flags); + if (unlikely(!mac->running)) { + /* Prevent reschedule on workqueue flush */ + spin_unlock_irqrestore(&mac->lock, flags); + return; + } net->authenticated = 0; net->authenticating = 1; /* add a timeout call so we eventually give up waiting for an auth reply */ @@ -124,6 +129,9 @@ ieee80211softmac_auth_resp(struct net_device *dev, struct ieee80211_auth *auth) unsigned long flags; u8 * data; + if (unlikely(!mac->running)) + return -ENODEV; + /* Find correct auth queue item */ spin_lock_irqsave(&mac->lock, flags); list_for_each(list_ptr, &mac->auth_queue) { @@ -298,8 +306,6 @@ ieee80211softmac_deauth_from_net(struct ieee80211softmac_device *mac, /* can't transmit data right now... */ netif_carrier_off(mac->dev); - /* let's try to re-associate */ - schedule_work(&mac->associnfo.work); spin_unlock_irqrestore(&mac->lock, flags); } @@ -338,6 +344,9 @@ ieee80211softmac_deauth_resp(struct net_device *dev, struct ieee80211_deauth *de struct ieee80211softmac_network *net = NULL; struct ieee80211softmac_device *mac = ieee80211_priv(dev); + if (unlikely(!mac->running)) + return -ENODEV; + if (!deauth) { dprintk("deauth without deauth packet. eek!\n"); return 0; @@ -360,5 +369,8 @@ ieee80211softmac_deauth_resp(struct net_device *dev, struct ieee80211_deauth *de } ieee80211softmac_deauth_from_net(mac, net); + + /* let's try to re-associate */ + schedule_work(&mac->associnfo.work); return 0; } diff --git a/net/ieee80211/softmac/ieee80211softmac_module.c b/net/ieee80211/softmac/ieee80211softmac_module.c index be83bdc1644..6252be2c0db 100644 --- a/net/ieee80211/softmac/ieee80211softmac_module.c +++ b/net/ieee80211/softmac/ieee80211softmac_module.c @@ -89,6 +89,8 @@ ieee80211softmac_clear_pending_work(struct ieee80211softmac_device *sm) ieee80211softmac_wait_for_scan(sm); spin_lock_irqsave(&sm->lock, flags); + sm->running = 0; + /* Free all pending assoc work items */ cancel_delayed_work(&sm->associnfo.work); @@ -204,6 +206,8 @@ void ieee80211softmac_start(struct net_device *dev) assert(0); if (mac->txrates_change) mac->txrates_change(dev, change, &oldrates); + + mac->running = 1; } EXPORT_SYMBOL_GPL(ieee80211softmac_start); diff --git a/net/ieee80211/softmac/ieee80211softmac_scan.c b/net/ieee80211/softmac/ieee80211softmac_scan.c index 2b9e7edfa3c..d31cf77498c 100644 --- a/net/ieee80211/softmac/ieee80211softmac_scan.c +++ b/net/ieee80211/softmac/ieee80211softmac_scan.c @@ -115,7 +115,15 @@ void ieee80211softmac_scan(void *d) // TODO: is this if correct, or should we do this only if scanning from assoc request? if (sm->associnfo.req_essid.len) ieee80211softmac_send_mgt_frame(sm, &sm->associnfo.req_essid, IEEE80211_STYPE_PROBE_REQ, 0); + + spin_lock_irqsave(&sm->lock, flags); + if (unlikely(!sm->running)) { + /* Prevent reschedule on workqueue flush */ + spin_unlock_irqrestore(&sm->lock, flags); + break; + } schedule_delayed_work(&si->softmac_scan, IEEE80211SOFTMAC_PROBE_DELAY); + spin_unlock_irqrestore(&sm->lock, flags); return; } else { dprintk(PFX "Not probing Channel %d (not allowed here)\n", si->channels[current_channel_idx].channel); diff --git a/net/ipv4/af_inet.c b/net/ipv4/af_inet.c index dc206f1f914..0a277453526 100644 --- a/net/ipv4/af_inet.c +++ b/net/ipv4/af_inet.c @@ -1257,7 +1257,7 @@ out_unregister_udp_proto: goto out; } -module_init(inet_init); +fs_initcall(inet_init); /* ------------------------------------------------------------------------ */ diff --git a/net/ipv4/ip_input.c b/net/ipv4/ip_input.c index 18d7fad474d..c9026dbf4c9 100644 --- a/net/ipv4/ip_input.c +++ b/net/ipv4/ip_input.c @@ -337,7 +337,7 @@ static inline int ip_rcv_finish(struct sk_buff *skb) * Initialise the virtual path cache for the packet. It describes * how the packet travels inside Linux networking. */ - if (likely(skb->dst == NULL)) { + if (skb->dst == NULL) { int err = ip_route_input(skb, iph->daddr, iph->saddr, iph->tos, skb->dev); if (unlikely(err)) { diff --git a/net/ipv4/ip_options.c b/net/ipv4/ip_options.c index 9bebad07bf2..cbcae654462 100644 --- a/net/ipv4/ip_options.c +++ b/net/ipv4/ip_options.c @@ -209,7 +209,7 @@ int ip_options_echo(struct ip_options * dopt, struct sk_buff * skb) void ip_options_fragment(struct sk_buff * skb) { - unsigned char * optptr = skb->nh.raw; + unsigned char * optptr = skb->nh.raw + sizeof(struct iphdr); struct ip_options * opt = &(IPCB(skb)->opt); int l = opt->optlen; int optlen; diff --git a/net/ipv4/netfilter/ip_conntrack_helper_h323.c b/net/ipv4/netfilter/ip_conntrack_helper_h323.c index 2c2fb700d83..518f581d39e 100644 --- a/net/ipv4/netfilter/ip_conntrack_helper_h323.c +++ b/net/ipv4/netfilter/ip_conntrack_helper_h323.c @@ -162,6 +162,8 @@ static int get_tpkt_data(struct sk_buff **pskb, struct ip_conntrack *ct, /* Validate TPKT length */ tpktlen = tpkt[2] * 256 + tpkt[3]; + if (tpktlen < 4) + goto clear_out; if (tpktlen > tcpdatalen) { if (tcpdatalen == 4) { /* Separate TPKT header */ /* Netmeeting sends TPKT header and data separately */ diff --git a/net/ipv4/netfilter/ip_conntrack_helper_h323_asn1.c b/net/ipv4/netfilter/ip_conntrack_helper_h323_asn1.c index 48078002e45..355a53a5b6c 100644 --- a/net/ipv4/netfilter/ip_conntrack_helper_h323_asn1.c +++ b/net/ipv4/netfilter/ip_conntrack_helper_h323_asn1.c @@ -2,7 +2,7 @@ * ip_conntrack_helper_h323_asn1.c - BER and PER decoding library for H.323 * conntrack/NAT module. * - * Copyright (c) 2006 by Jing Min Zhao <zhaojingmin@hotmail.com> + * Copyright (c) 2006 by Jing Min Zhao <zhaojingmin@users.sourceforge.net> * * This source code is licensed under General Public License version 2. * @@ -703,6 +703,10 @@ int decode_choice(bitstr_t * bs, field_t * f, char *base, int level) type = get_bits(bs, f->sz); } + /* Write Type */ + if (base) + *(unsigned *) base = type; + /* Check Range */ if (type >= f->ub) { /* Newer version? */ BYTE_ALIGN(bs); @@ -712,10 +716,6 @@ int decode_choice(bitstr_t * bs, field_t * f, char *base, int level) return H323_ERROR_NONE; } - /* Write Type */ - if (base) - *(unsigned *) base = type; - /* Transfer to son level */ son = &f->fields[type]; if (son->attr & STOP) { diff --git a/net/ipv4/netfilter/ip_conntrack_proto_sctp.c b/net/ipv4/netfilter/ip_conntrack_proto_sctp.c index 5259abd0fb4..0416073c560 100644 --- a/net/ipv4/netfilter/ip_conntrack_proto_sctp.c +++ b/net/ipv4/netfilter/ip_conntrack_proto_sctp.c @@ -235,12 +235,15 @@ static int do_basic_checks(struct ip_conntrack *conntrack, flag = 1; } - /* Cookie Ack/Echo chunks not the first OR - Init / Init Ack / Shutdown compl chunks not the only chunks */ - if ((sch->type == SCTP_CID_COOKIE_ACK + /* + * Cookie Ack/Echo chunks not the first OR + * Init / Init Ack / Shutdown compl chunks not the only chunks + * OR zero-length. + */ + if (((sch->type == SCTP_CID_COOKIE_ACK || sch->type == SCTP_CID_COOKIE_ECHO || flag) - && count !=0 ) { + && count !=0) || !sch->length) { DEBUGP("Basic checks failed\n"); return 1; } diff --git a/net/ipv4/netfilter/ip_nat_standalone.c b/net/ipv4/netfilter/ip_nat_standalone.c index 8f760b28617..67e676783da 100644 --- a/net/ipv4/netfilter/ip_nat_standalone.c +++ b/net/ipv4/netfilter/ip_nat_standalone.c @@ -219,8 +219,10 @@ ip_nat_out(unsigned int hooknum, const struct net_device *out, int (*okfn)(struct sk_buff *)) { +#ifdef CONFIG_XFRM struct ip_conntrack *ct; enum ip_conntrack_info ctinfo; +#endif unsigned int ret; /* root is playing with raw sockets. */ diff --git a/net/ipv4/netfilter/ip_tables.c b/net/ipv4/netfilter/ip_tables.c index d25ac8ba6eb..cee3397ec27 100644 --- a/net/ipv4/netfilter/ip_tables.c +++ b/net/ipv4/netfilter/ip_tables.c @@ -956,15 +956,16 @@ struct compat_ipt_standard_target compat_int_t verdict; }; -#define IPT_ST_OFFSET (sizeof(struct ipt_standard_target) - \ - sizeof(struct compat_ipt_standard_target)) - struct compat_ipt_standard { struct compat_ipt_entry entry; struct compat_ipt_standard_target target; }; +#define IPT_ST_LEN XT_ALIGN(sizeof(struct ipt_standard_target)) +#define IPT_ST_COMPAT_LEN COMPAT_XT_ALIGN(sizeof(struct compat_ipt_standard_target)) +#define IPT_ST_OFFSET (IPT_ST_LEN - IPT_ST_COMPAT_LEN) + static int compat_ipt_standard_fn(void *target, void **dstptr, int *size, int convert) { @@ -975,35 +976,29 @@ static int compat_ipt_standard_fn(void *target, ret = 0; switch (convert) { case COMPAT_TO_USER: - pst = (struct ipt_standard_target *)target; + pst = target; memcpy(&compat_st.target, &pst->target, - sizeof(struct ipt_entry_target)); + sizeof(compat_st.target)); compat_st.verdict = pst->verdict; if (compat_st.verdict > 0) compat_st.verdict -= compat_calc_jump(compat_st.verdict); - compat_st.target.u.user.target_size = - sizeof(struct compat_ipt_standard_target); - if (__copy_to_user(*dstptr, &compat_st, - sizeof(struct compat_ipt_standard_target))) + compat_st.target.u.user.target_size = IPT_ST_COMPAT_LEN; + if (copy_to_user(*dstptr, &compat_st, IPT_ST_COMPAT_LEN)) ret = -EFAULT; *size -= IPT_ST_OFFSET; - *dstptr += sizeof(struct compat_ipt_standard_target); + *dstptr += IPT_ST_COMPAT_LEN; break; case COMPAT_FROM_USER: - pcompat_st = - (struct compat_ipt_standard_target *)target; - memcpy(&st.target, &pcompat_st->target, - sizeof(struct ipt_entry_target)); + pcompat_st = target; + memcpy(&st.target, &pcompat_st->target, IPT_ST_COMPAT_LEN); st.verdict = pcompat_st->verdict; if (st.verdict > 0) st.verdict += compat_calc_jump(st.verdict); - st.target.u.user.target_size = - sizeof(struct ipt_standard_target); - memcpy(*dstptr, &st, - sizeof(struct ipt_standard_target)); + st.target.u.user.target_size = IPT_ST_LEN; + memcpy(*dstptr, &st, IPT_ST_LEN); *size += IPT_ST_OFFSET; - *dstptr += sizeof(struct ipt_standard_target); + *dstptr += IPT_ST_LEN; break; case COMPAT_CALC_SIZE: *size += IPT_ST_OFFSET; @@ -1446,7 +1441,7 @@ static int compat_copy_entry_to_user(struct ipt_entry *e, ret = -EFAULT; origsize = *size; ce = (struct compat_ipt_entry __user *)*dstptr; - if (__copy_to_user(ce, e, sizeof(struct ipt_entry))) + if (copy_to_user(ce, e, sizeof(struct ipt_entry))) goto out; *dstptr += sizeof(struct compat_ipt_entry); @@ -1464,9 +1459,9 @@ static int compat_copy_entry_to_user(struct ipt_entry *e, goto out; ret = -EFAULT; next_offset = e->next_offset - (origsize - *size); - if (__put_user(target_offset, &ce->target_offset)) + if (put_user(target_offset, &ce->target_offset)) goto out; - if (__put_user(next_offset, &ce->next_offset)) + if (put_user(next_offset, &ce->next_offset)) goto out; return 0; out: diff --git a/net/ipv4/tcp.c b/net/ipv4/tcp.c index 87f68e787d0..e2b7b805503 100644 --- a/net/ipv4/tcp.c +++ b/net/ipv4/tcp.c @@ -1468,6 +1468,7 @@ void tcp_close(struct sock *sk, long timeout) { struct sk_buff *skb; int data_was_unread = 0; + int state; lock_sock(sk); sk->sk_shutdown = SHUTDOWN_MASK; @@ -1544,6 +1545,11 @@ void tcp_close(struct sock *sk, long timeout) sk_stream_wait_close(sk, timeout); adjudge_to_death: + state = sk->sk_state; + sock_hold(sk); + sock_orphan(sk); + atomic_inc(sk->sk_prot->orphan_count); + /* It is the last release_sock in its life. It will remove backlog. */ release_sock(sk); @@ -1555,8 +1561,9 @@ adjudge_to_death: bh_lock_sock(sk); BUG_TRAP(!sock_owned_by_user(sk)); - sock_hold(sk); - sock_orphan(sk); + /* Have we already been destroyed by a softirq or backlog? */ + if (state != TCP_CLOSE && sk->sk_state == TCP_CLOSE) + goto out; /* This is a (useful) BSD violating of the RFC. There is a * problem with TCP as specified in that the other end could @@ -1584,7 +1591,6 @@ adjudge_to_death: if (tmo > TCP_TIMEWAIT_LEN) { inet_csk_reset_keepalive_timer(sk, tcp_fin_time(sk)); } else { - atomic_inc(sk->sk_prot->orphan_count); tcp_time_wait(sk, TCP_FIN_WAIT2, tmo); goto out; } @@ -1603,7 +1609,6 @@ adjudge_to_death: NET_INC_STATS_BH(LINUX_MIB_TCPABORTONMEMORY); } } - atomic_inc(sk->sk_prot->orphan_count); if (sk->sk_state == TCP_CLOSE) inet_csk_destroy_sock(sk); diff --git a/net/ipv4/tcp_highspeed.c b/net/ipv4/tcp_highspeed.c index e0e9d1383c7..b72fa55dfb8 100644 --- a/net/ipv4/tcp_highspeed.c +++ b/net/ipv4/tcp_highspeed.c @@ -137,8 +137,8 @@ static void hstcp_cong_avoid(struct sock *sk, u32 adk, u32 rtt, if (tp->snd_cwnd < tp->snd_cwnd_clamp) { tp->snd_cwnd_cnt += ca->ai; if (tp->snd_cwnd_cnt >= tp->snd_cwnd) { - tp->snd_cwnd++; tp->snd_cwnd_cnt -= tp->snd_cwnd; + tp->snd_cwnd++; } } } diff --git a/net/ipv4/tcp_output.c b/net/ipv4/tcp_output.c index a28ae593b97..743016baa04 100644 --- a/net/ipv4/tcp_output.c +++ b/net/ipv4/tcp_output.c @@ -465,7 +465,7 @@ static int tcp_transmit_skb(struct sock *sk, struct sk_buff *skb, int clone_it, TCP_INC_STATS(TCP_MIB_OUTSEGS); err = icsk->icsk_af_ops->queue_xmit(skb, 0); - if (unlikely(err <= 0)) + if (likely(err <= 0)) return err; tcp_enter_cwr(sk); diff --git a/net/ipv4/xfrm4_output.c b/net/ipv4/xfrm4_output.c index 32ad229b4fe..4ef8efaf6a6 100644 --- a/net/ipv4/xfrm4_output.c +++ b/net/ipv4/xfrm4_output.c @@ -62,7 +62,7 @@ static void xfrm4_encap(struct sk_buff *skb) top_iph->frag_off = (flags & XFRM_STATE_NOPMTUDISC) ? 0 : (iph->frag_off & htons(IP_DF)); if (!top_iph->frag_off) - __ip_select_ident(top_iph, dst, 0); + __ip_select_ident(top_iph, dst->child, 0); top_iph->ttl = dst_metric(dst->child, RTAX_HOPLIMIT); diff --git a/net/ipv6/inet6_connection_sock.c b/net/ipv6/inet6_connection_sock.c index f8f3a37a149..eb2865d5ae2 100644 --- a/net/ipv6/inet6_connection_sock.c +++ b/net/ipv6/inet6_connection_sock.c @@ -173,6 +173,7 @@ int inet6_csk_xmit(struct sk_buff *skb, int ipfragok) if (err) { sk->sk_err_soft = -err; + kfree_skb(skb); return err; } @@ -181,6 +182,7 @@ int inet6_csk_xmit(struct sk_buff *skb, int ipfragok) if ((err = xfrm_lookup(&dst, &fl, sk, 0)) < 0) { sk->sk_route_caps = 0; + kfree_skb(skb); return err; } diff --git a/net/ipv6/route.c b/net/ipv6/route.c index 79078747a64..0190e39096b 100644 --- a/net/ipv6/route.c +++ b/net/ipv6/route.c @@ -317,7 +317,7 @@ static struct rt6_info *rt6_select(struct rt6_info **head, int oif, __FUNCTION__, head, head ? *head : NULL, oif); for (rt = rt0, metric = rt0->rt6i_metric; - rt && rt->rt6i_metric == metric; + rt && rt->rt6i_metric == metric && (!last || rt != rt0); rt = rt->u.next) { int m; @@ -343,9 +343,12 @@ static struct rt6_info *rt6_select(struct rt6_info **head, int oif, (strict & RT6_SELECT_F_REACHABLE) && last && last != rt0) { /* no entries matched; do round-robin */ + static spinlock_t lock = SPIN_LOCK_UNLOCKED; + spin_lock(&lock); *head = rt0->u.next; rt0->u.next = last->u.next; last->u.next = rt0; + spin_unlock(&lock); } RT6_TRACE("%s() => %p, score=%d\n", diff --git a/net/irda/irias_object.c b/net/irda/irias_object.c index c6d169fbdce..82e665c7999 100644 --- a/net/irda/irias_object.c +++ b/net/irda/irias_object.c @@ -257,7 +257,6 @@ struct ias_attrib *irias_find_attrib(struct ias_object *obj, char *name) /* Unsafe (locking), attrib might change */ return attrib; } -EXPORT_SYMBOL(irias_find_attrib); /* * Function irias_add_attribute (obj, attrib) @@ -484,7 +483,6 @@ struct ias_value *irias_new_string_value(char *string) return value; } -EXPORT_SYMBOL(irias_new_string_value); /* * Function irias_new_octseq_value (octets, len) @@ -519,7 +517,6 @@ struct ias_value *irias_new_octseq_value(__u8 *octseq , int len) memcpy(value->t.oct_seq, octseq , len); return value; } -EXPORT_SYMBOL(irias_new_octseq_value); struct ias_value *irias_new_missing_value(void) { diff --git a/net/netfilter/nf_conntrack_proto_sctp.c b/net/netfilter/nf_conntrack_proto_sctp.c index 9cccc325b68..0c6da496cfa 100644 --- a/net/netfilter/nf_conntrack_proto_sctp.c +++ b/net/netfilter/nf_conntrack_proto_sctp.c @@ -240,12 +240,15 @@ static int do_basic_checks(struct nf_conn *conntrack, flag = 1; } - /* Cookie Ack/Echo chunks not the first OR - Init / Init Ack / Shutdown compl chunks not the only chunks */ - if ((sch->type == SCTP_CID_COOKIE_ACK + /* + * Cookie Ack/Echo chunks not the first OR + * Init / Init Ack / Shutdown compl chunks not the only chunks + * OR zero-length. + */ + if (((sch->type == SCTP_CID_COOKIE_ACK || sch->type == SCTP_CID_COOKIE_ECHO || flag) - && count !=0 ) { + && count !=0) || !sch->length) { DEBUGP("Basic checks failed\n"); return 1; } diff --git a/net/netfilter/x_tables.c b/net/netfilter/x_tables.c index 17abf60f957..99293c63ff7 100644 --- a/net/netfilter/x_tables.c +++ b/net/netfilter/x_tables.c @@ -289,7 +289,7 @@ int xt_compat_match(void *match, void **dstptr, int *size, int convert) case COMPAT_TO_USER: pm = (struct xt_entry_match *)match; msize = pm->u.user.match_size; - if (__copy_to_user(*dstptr, pm, msize)) { + if (copy_to_user(*dstptr, pm, msize)) { ret = -EFAULT; break; } @@ -366,7 +366,7 @@ int xt_compat_target(void *target, void **dstptr, int *size, int convert) case COMPAT_TO_USER: pt = (struct xt_entry_target *)target; tsize = pt->u.user.target_size; - if (__copy_to_user(*dstptr, pt, tsize)) { + if (copy_to_user(*dstptr, pt, tsize)) { ret = -EFAULT; break; } diff --git a/net/netlink/af_netlink.c b/net/netlink/af_netlink.c index 2a233ffcf61..3862e73d14d 100644 --- a/net/netlink/af_netlink.c +++ b/net/netlink/af_netlink.c @@ -56,12 +56,12 @@ #include <linux/mm.h> #include <linux/types.h> #include <linux/audit.h> +#include <linux/selinux.h> #include <net/sock.h> #include <net/scm.h> #include <net/netlink.h> -#define Nprintk(a...) #define NLGRPSZ(x) (ALIGN(x, sizeof(unsigned long) * 8) / 8) struct netlink_sock { @@ -1157,6 +1157,7 @@ static int netlink_sendmsg(struct kiocb *kiocb, struct socket *sock, NETLINK_CB(skb).dst_pid = dst_pid; NETLINK_CB(skb).dst_group = dst_group; NETLINK_CB(skb).loginuid = audit_get_loginuid(current->audit_context); + selinux_get_task_sid(current, &(NETLINK_CB(skb).sid)); memcpy(NETLINK_CREDS(skb), &siocb->scm->creds, sizeof(struct ucred)); /* What can I do? Netlink is asynchronous, so that diff --git a/net/netrom/af_netrom.c b/net/netrom/af_netrom.c index d44981f5a61..3669cb953e6 100644 --- a/net/netrom/af_netrom.c +++ b/net/netrom/af_netrom.c @@ -425,11 +425,16 @@ static int nr_create(struct socket *sock, int protocol) nr_init_timers(sk); - nr->t1 = sysctl_netrom_transport_timeout; - nr->t2 = sysctl_netrom_transport_acknowledge_delay; - nr->n2 = sysctl_netrom_transport_maximum_tries; - nr->t4 = sysctl_netrom_transport_busy_delay; - nr->idle = sysctl_netrom_transport_no_activity_timeout; + nr->t1 = + msecs_to_jiffies(sysctl_netrom_transport_timeout); + nr->t2 = + msecs_to_jiffies(sysctl_netrom_transport_acknowledge_delay); + nr->n2 = + msecs_to_jiffies(sysctl_netrom_transport_maximum_tries); + nr->t4 = + msecs_to_jiffies(sysctl_netrom_transport_busy_delay); + nr->idle = + msecs_to_jiffies(sysctl_netrom_transport_no_activity_timeout); nr->window = sysctl_netrom_transport_requested_window_size; nr->bpqext = 1; @@ -1365,8 +1370,6 @@ static struct notifier_block nr_dev_notifier = { static struct net_device **dev_nr; -static char banner[] __initdata = KERN_INFO "G4KLX NET/ROM for Linux. Version 0.7 for AX25.037 Linux 2.4\n"; - static int __init nr_proto_init(void) { int i; @@ -1414,7 +1417,6 @@ static int __init nr_proto_init(void) } register_netdevice_notifier(&nr_dev_notifier); - printk(banner); ax25_protocol_register(AX25_P_NETROM, nr_route_frame); ax25_linkfail_register(nr_link_failed); diff --git a/net/netrom/nr_dev.c b/net/netrom/nr_dev.c index 509afddae56..621e5586ab0 100644 --- a/net/netrom/nr_dev.c +++ b/net/netrom/nr_dev.c @@ -185,7 +185,6 @@ static struct net_device_stats *nr_get_stats(struct net_device *dev) void nr_setup(struct net_device *dev) { - SET_MODULE_OWNER(dev); dev->mtu = NR_MAX_PACKET_SIZE; dev->hard_start_xmit = nr_xmit; dev->open = nr_open; diff --git a/net/rose/af_rose.c b/net/rose/af_rose.c index ea65396d161..55564efccf1 100644 --- a/net/rose/af_rose.c +++ b/net/rose/af_rose.c @@ -518,11 +518,11 @@ static int rose_create(struct socket *sock, int protocol) init_timer(&rose->timer); init_timer(&rose->idletimer); - rose->t1 = sysctl_rose_call_request_timeout; - rose->t2 = sysctl_rose_reset_request_timeout; - rose->t3 = sysctl_rose_clear_request_timeout; - rose->hb = sysctl_rose_ack_hold_back_timeout; - rose->idle = sysctl_rose_no_activity_timeout; + rose->t1 = msecs_to_jiffies(sysctl_rose_call_request_timeout); + rose->t2 = msecs_to_jiffies(sysctl_rose_reset_request_timeout); + rose->t3 = msecs_to_jiffies(sysctl_rose_clear_request_timeout); + rose->hb = msecs_to_jiffies(sysctl_rose_ack_hold_back_timeout); + rose->idle = msecs_to_jiffies(sysctl_rose_no_activity_timeout); rose->state = ROSE_STATE_0; @@ -1469,8 +1469,6 @@ static struct notifier_block rose_dev_notifier = { static struct net_device **dev_rose; -static const char banner[] = KERN_INFO "F6FBB/G4KLX ROSE for Linux. Version 0.62 for AX25.037 Linux 2.4\n"; - static int __init rose_proto_init(void) { int i; @@ -1519,7 +1517,6 @@ static int __init rose_proto_init(void) sock_register(&rose_family_ops); register_netdevice_notifier(&rose_dev_notifier); - printk(banner); ax25_protocol_register(AX25_P_ROSE, rose_route_frame); ax25_linkfail_register(rose_link_failed); diff --git a/net/rose/rose_dev.c b/net/rose/rose_dev.c index d297af737d1..2a1bf8e119e 100644 --- a/net/rose/rose_dev.c +++ b/net/rose/rose_dev.c @@ -135,7 +135,6 @@ static struct net_device_stats *rose_get_stats(struct net_device *dev) void rose_setup(struct net_device *dev) { - SET_MODULE_OWNER(dev); dev->mtu = ROSE_MAX_PACKET_SIZE - 2; dev->hard_start_xmit = rose_xmit; dev->open = rose_open; diff --git a/net/rose/rose_link.c b/net/rose/rose_link.c index 09e9e9d04d9..bd86a63960c 100644 --- a/net/rose/rose_link.c +++ b/net/rose/rose_link.c @@ -40,7 +40,8 @@ void rose_start_ftimer(struct rose_neigh *neigh) neigh->ftimer.data = (unsigned long)neigh; neigh->ftimer.function = &rose_ftimer_expiry; - neigh->ftimer.expires = jiffies + sysctl_rose_link_fail_timeout; + neigh->ftimer.expires = + jiffies + msecs_to_jiffies(sysctl_rose_link_fail_timeout); add_timer(&neigh->ftimer); } @@ -51,7 +52,8 @@ static void rose_start_t0timer(struct rose_neigh *neigh) neigh->t0timer.data = (unsigned long)neigh; neigh->t0timer.function = &rose_t0timer_expiry; - neigh->t0timer.expires = jiffies + sysctl_rose_restart_request_timeout; + neigh->t0timer.expires = + jiffies + msecs_to_jiffies(sysctl_rose_restart_request_timeout); add_timer(&neigh->t0timer); } diff --git a/net/rose/rose_route.c b/net/rose/rose_route.c index 8631b65a731..a22542fa1bc 100644 --- a/net/rose/rose_route.c +++ b/net/rose/rose_route.c @@ -48,8 +48,6 @@ static DEFINE_SPINLOCK(rose_route_list_lock); struct rose_neigh *rose_loopback_neigh; -static void rose_remove_neigh(struct rose_neigh *); - /* * Add a new route to a node, and in the process add the node and the * neighbour if it is new. @@ -235,11 +233,8 @@ static void rose_remove_neigh(struct rose_neigh *rose_neigh) skb_queue_purge(&rose_neigh->queue); - spin_lock_bh(&rose_neigh_list_lock); - if ((s = rose_neigh_list) == rose_neigh) { rose_neigh_list = rose_neigh->next; - spin_unlock_bh(&rose_neigh_list_lock); kfree(rose_neigh->digipeat); kfree(rose_neigh); return; @@ -248,7 +243,6 @@ static void rose_remove_neigh(struct rose_neigh *rose_neigh) while (s != NULL && s->next != NULL) { if (s->next == rose_neigh) { s->next = rose_neigh->next; - spin_unlock_bh(&rose_neigh_list_lock); kfree(rose_neigh->digipeat); kfree(rose_neigh); return; @@ -256,7 +250,6 @@ static void rose_remove_neigh(struct rose_neigh *rose_neigh) s = s->next; } - spin_unlock_bh(&rose_neigh_list_lock); } /* diff --git a/net/sched/sch_hfsc.c b/net/sched/sch_hfsc.c index 91132f6871d..f1c7bd29f2c 100644 --- a/net/sched/sch_hfsc.c +++ b/net/sched/sch_hfsc.c @@ -974,10 +974,10 @@ hfsc_adjust_levels(struct hfsc_class *cl) do { level = 0; list_for_each_entry(p, &cl->children, siblings) { - if (p->level > level) - level = p->level; + if (p->level >= level) + level = p->level + 1; } - cl->level = level + 1; + cl->level = level; } while ((cl = cl->cl_parent) != NULL); } diff --git a/net/sched/sch_netem.c b/net/sched/sch_netem.c index 7228d30512c..5a4a4d0ae50 100644 --- a/net/sched/sch_netem.c +++ b/net/sched/sch_netem.c @@ -167,7 +167,7 @@ static int netem_enqueue(struct sk_buff *skb, struct Qdisc *sch) if (count == 0) { sch->qstats.drops++; kfree_skb(skb); - return NET_XMIT_DROP; + return NET_XMIT_BYPASS; } /* diff --git a/net/sctp/inqueue.c b/net/sctp/inqueue.c index 297b8951463..cf0c767d43a 100644 --- a/net/sctp/inqueue.c +++ b/net/sctp/inqueue.c @@ -149,6 +149,7 @@ struct sctp_chunk *sctp_inq_pop(struct sctp_inq *queue) /* This is the first chunk in the packet. */ chunk->singleton = 1; ch = (sctp_chunkhdr_t *) chunk->skb->data; + chunk->data_accepted = 0; } chunk->chunk_hdr = ch; diff --git a/net/sctp/sm_statefuns.c b/net/sctp/sm_statefuns.c index 2b9a832b29a..8cdba51ec07 100644 --- a/net/sctp/sm_statefuns.c +++ b/net/sctp/sm_statefuns.c @@ -636,8 +636,9 @@ sctp_disposition_t sctp_sf_do_5_1D_ce(const struct sctp_endpoint *ep, */ chunk->subh.cookie_hdr = (struct sctp_signed_cookie *)chunk->skb->data; - skb_pull(chunk->skb, - ntohs(chunk->chunk_hdr->length) - sizeof(sctp_chunkhdr_t)); + if (!pskb_pull(chunk->skb, ntohs(chunk->chunk_hdr->length) - + sizeof(sctp_chunkhdr_t))) + goto nomem; /* 5.1 D) Upon reception of the COOKIE ECHO chunk, Endpoint * "Z" will reply with a COOKIE ACK chunk after building a TCB @@ -965,7 +966,8 @@ sctp_disposition_t sctp_sf_beat_8_3(const struct sctp_endpoint *ep, */ chunk->subh.hb_hdr = (sctp_heartbeathdr_t *) chunk->skb->data; paylen = ntohs(chunk->chunk_hdr->length) - sizeof(sctp_chunkhdr_t); - skb_pull(chunk->skb, paylen); + if (!pskb_pull(chunk->skb, paylen)) + goto nomem; reply = sctp_make_heartbeat_ack(asoc, chunk, chunk->subh.hb_hdr, paylen); @@ -1860,8 +1862,9 @@ sctp_disposition_t sctp_sf_do_5_2_4_dupcook(const struct sctp_endpoint *ep, * are in good shape. */ chunk->subh.cookie_hdr = (struct sctp_signed_cookie *)chunk->skb->data; - skb_pull(chunk->skb, ntohs(chunk->chunk_hdr->length) - - sizeof(sctp_chunkhdr_t)); + if (!pskb_pull(chunk->skb, ntohs(chunk->chunk_hdr->length) - + sizeof(sctp_chunkhdr_t))) + goto nomem; /* In RFC 2960 5.2.4 3, if both Verification Tags in the State Cookie * of a duplicate COOKIE ECHO match the Verification Tags of the @@ -5151,7 +5154,9 @@ static int sctp_eat_data(const struct sctp_association *asoc, int tmp; __u32 tsn; int account_value; + struct sctp_tsnmap *map = (struct sctp_tsnmap *)&asoc->peer.tsn_map; struct sock *sk = asoc->base.sk; + int rcvbuf_over = 0; data_hdr = chunk->subh.data_hdr = (sctp_datahdr_t *)chunk->skb->data; skb_pull(chunk->skb, sizeof(sctp_datahdr_t)); @@ -5162,10 +5167,16 @@ static int sctp_eat_data(const struct sctp_association *asoc, /* ASSERT: Now skb->data is really the user data. */ /* - * if we are established, and we have used up our receive - * buffer memory, drop the frame - */ - if (asoc->state == SCTP_STATE_ESTABLISHED) { + * If we are established, and we have used up our receive buffer + * memory, think about droping the frame. + * Note that we have an opportunity to improve performance here. + * If we accept one chunk from an skbuff, we have to keep all the + * memory of that skbuff around until the chunk is read into user + * space. Therefore, once we accept 1 chunk we may as well accept all + * remaining chunks in the skbuff. The data_accepted flag helps us do + * that. + */ + if ((asoc->state == SCTP_STATE_ESTABLISHED) && (!chunk->data_accepted)) { /* * If the receive buffer policy is 1, then each * association can allocate up to sk_rcvbuf bytes @@ -5176,9 +5187,25 @@ static int sctp_eat_data(const struct sctp_association *asoc, account_value = atomic_read(&asoc->rmem_alloc); else account_value = atomic_read(&sk->sk_rmem_alloc); - - if (account_value > sk->sk_rcvbuf) - return SCTP_IERROR_IGNORE_TSN; + if (account_value > sk->sk_rcvbuf) { + /* + * We need to make forward progress, even when we are + * under memory pressure, so we always allow the + * next tsn after the ctsn ack point to be accepted. + * This lets us avoid deadlocks in which we have to + * drop frames that would otherwise let us drain the + * receive queue. + */ + if ((sctp_tsnmap_get_ctsn(map) + 1) != tsn) + return SCTP_IERROR_IGNORE_TSN; + + /* + * We're going to accept the frame but we should renege + * to make space for it. This will send us down that + * path later in this function. + */ + rcvbuf_over = 1; + } } /* Process ECN based congestion. @@ -5226,6 +5253,7 @@ static int sctp_eat_data(const struct sctp_association *asoc, datalen -= sizeof(sctp_data_chunk_t); deliver = SCTP_CMD_CHUNK_ULP; + chunk->data_accepted = 1; /* Think about partial delivery. */ if ((datalen >= asoc->rwnd) && (!asoc->ulpq.pd_mode)) { @@ -5242,7 +5270,8 @@ static int sctp_eat_data(const struct sctp_association *asoc, * large spill over. */ if (!asoc->rwnd || asoc->rwnd_over || - (datalen > asoc->rwnd + asoc->frag_point)) { + (datalen > asoc->rwnd + asoc->frag_point) || + rcvbuf_over) { /* If this is the next TSN, consider reneging to make * room. Note: Playing nice with a confused sender. A @@ -5250,8 +5279,8 @@ static int sctp_eat_data(const struct sctp_association *asoc, * space and in the future we may want to detect and * do more drastic reneging. */ - if (sctp_tsnmap_has_gap(&asoc->peer.tsn_map) && - (sctp_tsnmap_get_ctsn(&asoc->peer.tsn_map) + 1) == tsn) { + if (sctp_tsnmap_has_gap(map) && + (sctp_tsnmap_get_ctsn(map) + 1) == tsn) { SCTP_DEBUG_PRINTK("Reneging for tsn:%u\n", tsn); deliver = SCTP_CMD_RENEGE; } else { diff --git a/net/sctp/sm_statetable.c b/net/sctp/sm_statetable.c index 75ef1040876..8bcca567615 100644 --- a/net/sctp/sm_statetable.c +++ b/net/sctp/sm_statetable.c @@ -366,9 +366,9 @@ const sctp_sm_table_entry_t *sctp_sm_lookup_event(sctp_event_t event_type, /* SCTP_STATE_EMPTY */ \ {.fn = sctp_sf_ootb, .name = "sctp_sf_ootb"}, \ /* SCTP_STATE_CLOSED */ \ - {.fn = sctp_sf_bug, .name = "sctp_sf_bug"}, \ + {.fn = sctp_sf_discard_chunk, .name = "sctp_sf_discard_chunk"}, \ /* SCTP_STATE_COOKIE_WAIT */ \ - {.fn = sctp_sf_bug, .name = "sctp_sf_bug"}, \ + {.fn = sctp_sf_discard_chunk, .name = "sctp_sf_discard_chunk"}, \ /* SCTP_STATE_COOKIE_ECHOED */ \ {.fn = sctp_sf_do_ecne, .name = "sctp_sf_do_ecne"}, \ /* SCTP_STATE_ESTABLISHED */ \ @@ -380,7 +380,7 @@ const sctp_sm_table_entry_t *sctp_sm_lookup_event(sctp_event_t event_type, /* SCTP_STATE_SHUTDOWN_RECEIVED */ \ {.fn = sctp_sf_do_ecne, .name = "sctp_sf_do_ecne"}, \ /* SCTP_STATE_SHUTDOWN_ACK_SENT */ \ - {.fn = sctp_sf_bug, .name = "sctp_sf_bug"}, \ + {.fn = sctp_sf_discard_chunk, .name = "sctp_sf_discard_chunk"}, \ } /* TYPE_SCTP_ECN_ECNE */ #define TYPE_SCTP_ECN_CWR { \ @@ -401,7 +401,7 @@ const sctp_sm_table_entry_t *sctp_sm_lookup_event(sctp_event_t event_type, /* SCTP_STATE_SHUTDOWN_RECEIVED */ \ {.fn = sctp_sf_discard_chunk, .name = "sctp_sf_discard_chunk"}, \ /* SCTP_STATE_SHUTDOWN_ACK_SENT */ \ - {.fn = sctp_sf_bug, .name = "sctp_sf_bug"}, \ + {.fn = sctp_sf_discard_chunk, .name = "sctp_sf_discard_chunk"}, \ } /* TYPE_SCTP_ECN_CWR */ #define TYPE_SCTP_SHUTDOWN_COMPLETE { \ @@ -647,7 +647,7 @@ chunk_event_table_unknown[SCTP_STATE_NUM_STATES] = { /* SCTP_STATE_EMPTY */ \ {.fn = sctp_sf_bug, .name = "sctp_sf_bug"}, \ /* SCTP_STATE_CLOSED */ \ - {.fn = sctp_sf_bug, .name = "sctp_sf_bug"}, \ + {.fn = sctp_sf_error_closed, .name = "sctp_sf_error_closed"}, \ /* SCTP_STATE_COOKIE_WAIT */ \ {.fn = sctp_sf_do_prm_requestheartbeat, \ .name = "sctp_sf_do_prm_requestheartbeat"}, \ diff --git a/net/sctp/ulpqueue.c b/net/sctp/ulpqueue.c index 2080b2d28c9..575e556aeb3 100644 --- a/net/sctp/ulpqueue.c +++ b/net/sctp/ulpqueue.c @@ -279,6 +279,7 @@ static inline void sctp_ulpq_store_reasm(struct sctp_ulpq *ulpq, static struct sctp_ulpevent *sctp_make_reassembled_event(struct sk_buff_head *queue, struct sk_buff *f_frag, struct sk_buff *l_frag) { struct sk_buff *pos; + struct sk_buff *new = NULL; struct sctp_ulpevent *event; struct sk_buff *pnext, *last; struct sk_buff *list = skb_shinfo(f_frag)->frag_list; @@ -297,11 +298,33 @@ static struct sctp_ulpevent *sctp_make_reassembled_event(struct sk_buff_head *qu */ if (last) last->next = pos; - else - skb_shinfo(f_frag)->frag_list = pos; + else { + if (skb_cloned(f_frag)) { + /* This is a cloned skb, we can't just modify + * the frag_list. We need a new skb to do that. + * Instead of calling skb_unshare(), we'll do it + * ourselves since we need to delay the free. + */ + new = skb_copy(f_frag, GFP_ATOMIC); + if (!new) + return NULL; /* try again later */ + + new->sk = f_frag->sk; + + skb_shinfo(new)->frag_list = pos; + } else + skb_shinfo(f_frag)->frag_list = pos; + } /* Remove the first fragment from the reassembly queue. */ __skb_unlink(f_frag, queue); + + /* if we did unshare, then free the old skb and re-assign */ + if (new) { + kfree_skb(f_frag); + f_frag = new; + } + while (pos) { pnext = pos->next; diff --git a/net/socket.c b/net/socket.c index 0ce12dfc7a7..02948b622bd 100644 --- a/net/socket.c +++ b/net/socket.c @@ -267,6 +267,8 @@ int move_addr_to_user(void *kaddr, int klen, void __user *uaddr, int __user *ule return -EINVAL; if(len) { + if (audit_sockaddr(klen, kaddr)) + return -ENOMEM; if(copy_to_user(uaddr,kaddr,len)) return -EFAULT; } diff --git a/net/x25/x25_timer.c b/net/x25/x25_timer.c index 0a92e1da392..71ff3088f6f 100644 --- a/net/x25/x25_timer.c +++ b/net/x25/x25_timer.c @@ -114,8 +114,9 @@ static void x25_heartbeat_expiry(unsigned long param) if (sock_flag(sk, SOCK_DESTROY) || (sk->sk_state == TCP_LISTEN && sock_flag(sk, SOCK_DEAD))) { + bh_unlock_sock(sk); x25_destroy_socket(sk); - goto unlock; + return; } break; @@ -128,7 +129,6 @@ static void x25_heartbeat_expiry(unsigned long param) } restart_heartbeat: x25_start_heartbeat(sk); -unlock: bh_unlock_sock(sk); } diff --git a/net/xfrm/xfrm_policy.c b/net/xfrm/xfrm_policy.c index c3725fe2a8f..b469c8b5461 100644 --- a/net/xfrm/xfrm_policy.c +++ b/net/xfrm/xfrm_policy.c @@ -57,12 +57,12 @@ int xfrm_register_type(struct xfrm_type *type, unsigned short family) return -EAFNOSUPPORT; typemap = afinfo->type_map; - write_lock(&typemap->lock); + write_lock_bh(&typemap->lock); if (likely(typemap->map[type->proto] == NULL)) typemap->map[type->proto] = type; else err = -EEXIST; - write_unlock(&typemap->lock); + write_unlock_bh(&typemap->lock); xfrm_policy_put_afinfo(afinfo); return err; } @@ -78,12 +78,12 @@ int xfrm_unregister_type(struct xfrm_type *type, unsigned short family) return -EAFNOSUPPORT; typemap = afinfo->type_map; - write_lock(&typemap->lock); + write_lock_bh(&typemap->lock); if (unlikely(typemap->map[type->proto] != type)) err = -ENOENT; else typemap->map[type->proto] = NULL; - write_unlock(&typemap->lock); + write_unlock_bh(&typemap->lock); xfrm_policy_put_afinfo(afinfo); return err; } @@ -1251,7 +1251,7 @@ int xfrm_policy_register_afinfo(struct xfrm_policy_afinfo *afinfo) return -EINVAL; if (unlikely(afinfo->family >= NPROTO)) return -EAFNOSUPPORT; - write_lock(&xfrm_policy_afinfo_lock); + write_lock_bh(&xfrm_policy_afinfo_lock); if (unlikely(xfrm_policy_afinfo[afinfo->family] != NULL)) err = -ENOBUFS; else { @@ -1268,7 +1268,7 @@ int xfrm_policy_register_afinfo(struct xfrm_policy_afinfo *afinfo) afinfo->garbage_collect = __xfrm_garbage_collect; xfrm_policy_afinfo[afinfo->family] = afinfo; } - write_unlock(&xfrm_policy_afinfo_lock); + write_unlock_bh(&xfrm_policy_afinfo_lock); return err; } EXPORT_SYMBOL(xfrm_policy_register_afinfo); @@ -1280,7 +1280,7 @@ int xfrm_policy_unregister_afinfo(struct xfrm_policy_afinfo *afinfo) return -EINVAL; if (unlikely(afinfo->family >= NPROTO)) return -EAFNOSUPPORT; - write_lock(&xfrm_policy_afinfo_lock); + write_lock_bh(&xfrm_policy_afinfo_lock); if (likely(xfrm_policy_afinfo[afinfo->family] != NULL)) { if (unlikely(xfrm_policy_afinfo[afinfo->family] != afinfo)) err = -EINVAL; @@ -1294,7 +1294,7 @@ int xfrm_policy_unregister_afinfo(struct xfrm_policy_afinfo *afinfo) afinfo->garbage_collect = NULL; } } - write_unlock(&xfrm_policy_afinfo_lock); + write_unlock_bh(&xfrm_policy_afinfo_lock); return err; } EXPORT_SYMBOL(xfrm_policy_unregister_afinfo); diff --git a/net/xfrm/xfrm_state.c b/net/xfrm/xfrm_state.c index 3dc3e1f3b7a..93a2f36ad3d 100644 --- a/net/xfrm/xfrm_state.c +++ b/net/xfrm/xfrm_state.c @@ -1061,7 +1061,7 @@ int xfrm_state_register_afinfo(struct xfrm_state_afinfo *afinfo) return -EINVAL; if (unlikely(afinfo->family >= NPROTO)) return -EAFNOSUPPORT; - write_lock(&xfrm_state_afinfo_lock); + write_lock_bh(&xfrm_state_afinfo_lock); if (unlikely(xfrm_state_afinfo[afinfo->family] != NULL)) err = -ENOBUFS; else { @@ -1069,7 +1069,7 @@ int xfrm_state_register_afinfo(struct xfrm_state_afinfo *afinfo) afinfo->state_byspi = xfrm_state_byspi; xfrm_state_afinfo[afinfo->family] = afinfo; } - write_unlock(&xfrm_state_afinfo_lock); + write_unlock_bh(&xfrm_state_afinfo_lock); return err; } EXPORT_SYMBOL(xfrm_state_register_afinfo); @@ -1081,7 +1081,7 @@ int xfrm_state_unregister_afinfo(struct xfrm_state_afinfo *afinfo) return -EINVAL; if (unlikely(afinfo->family >= NPROTO)) return -EAFNOSUPPORT; - write_lock(&xfrm_state_afinfo_lock); + write_lock_bh(&xfrm_state_afinfo_lock); if (likely(xfrm_state_afinfo[afinfo->family] != NULL)) { if (unlikely(xfrm_state_afinfo[afinfo->family] != afinfo)) err = -EINVAL; @@ -1091,7 +1091,7 @@ int xfrm_state_unregister_afinfo(struct xfrm_state_afinfo *afinfo) afinfo->state_bydst = NULL; } } - write_unlock(&xfrm_state_afinfo_lock); + write_unlock_bh(&xfrm_state_afinfo_lock); return err; } EXPORT_SYMBOL(xfrm_state_unregister_afinfo); diff --git a/scripts/gen_initramfs_list.sh b/scripts/gen_initramfs_list.sh index 56b3bed1108..331c079f029 100644 --- a/scripts/gen_initramfs_list.sh +++ b/scripts/gen_initramfs_list.sh @@ -200,7 +200,11 @@ input_file() { print_mtime "$1" >> ${output} cat "$1" >> ${output} else - grep ^file "$1" | cut -d ' ' -f 3 + cat "$1" | while read type dir file perm ; do + if [ "$type" == "file" ]; then + echo "$file \\"; + fi + done fi elif [ -d "$1" ]; then dir_filelist "$1" diff --git a/scripts/mkmakefile b/scripts/mkmakefile index a22cbedd3b3..7f9d544f9b6 100644 --- a/scripts/mkmakefile +++ b/scripts/mkmakefile @@ -10,7 +10,10 @@ # $4 - patchlevel -cat << EOF +test ! -r $2/Makefile -o -O $2/Makefile || exit 0 +echo " GEN $2/Makefile" + +cat << EOF > $2/Makefile # Automatically generated by $0: don't edit VERSION = $3 diff --git a/scripts/mod/file2alias.c b/scripts/mod/file2alias.c index 84e21201f3c..37f67c23e11 100644 --- a/scripts/mod/file2alias.c +++ b/scripts/mod/file2alias.c @@ -374,10 +374,10 @@ static void do_input(char *alias, kernel_ulong_t *arr, unsigned int min, unsigned int max) { unsigned int i; - for (i = min; i < max; i++) { - if (arr[i/BITS_PER_LONG] & (1 << (i%BITS_PER_LONG))) - sprintf(alias+strlen(alias), "%X,*", i); - } + + for (i = min; i < max; i++) + if (arr[i / BITS_PER_LONG] & (1 << (i%BITS_PER_LONG))) + sprintf(alias + strlen(alias), "%X,*", i); } /* input:b0v0p0e0-eXkXrXaXmXlXsXfXwX where X is comma-separated %02X. */ @@ -386,39 +386,37 @@ static int do_input_entry(const char *filename, struct input_device_id *id, { sprintf(alias, "input:"); - ADD(alias, "b", id->flags&INPUT_DEVICE_ID_MATCH_BUS, id->id.bustype); - ADD(alias, "v", id->flags&INPUT_DEVICE_ID_MATCH_VENDOR, id->id.vendor); - ADD(alias, "p", id->flags&INPUT_DEVICE_ID_MATCH_PRODUCT, - id->id.product); - ADD(alias, "e", id->flags&INPUT_DEVICE_ID_MATCH_VERSION, - id->id.version); + ADD(alias, "b", id->flags & INPUT_DEVICE_ID_MATCH_BUS, id->bustype); + ADD(alias, "v", id->flags & INPUT_DEVICE_ID_MATCH_VENDOR, id->vendor); + ADD(alias, "p", id->flags & INPUT_DEVICE_ID_MATCH_PRODUCT, id->product); + ADD(alias, "e", id->flags & INPUT_DEVICE_ID_MATCH_VERSION, id->version); sprintf(alias + strlen(alias), "-e*"); - if (id->flags&INPUT_DEVICE_ID_MATCH_EVBIT) + if (id->flags & INPUT_DEVICE_ID_MATCH_EVBIT) do_input(alias, id->evbit, 0, EV_MAX); sprintf(alias + strlen(alias), "k*"); - if (id->flags&INPUT_DEVICE_ID_MATCH_KEYBIT) + if (id->flags & INPUT_DEVICE_ID_MATCH_KEYBIT) do_input(alias, id->keybit, KEY_MIN_INTERESTING, KEY_MAX); sprintf(alias + strlen(alias), "r*"); - if (id->flags&INPUT_DEVICE_ID_MATCH_RELBIT) + if (id->flags & INPUT_DEVICE_ID_MATCH_RELBIT) do_input(alias, id->relbit, 0, REL_MAX); sprintf(alias + strlen(alias), "a*"); - if (id->flags&INPUT_DEVICE_ID_MATCH_ABSBIT) + if (id->flags & INPUT_DEVICE_ID_MATCH_ABSBIT) do_input(alias, id->absbit, 0, ABS_MAX); sprintf(alias + strlen(alias), "m*"); - if (id->flags&INPUT_DEVICE_ID_MATCH_MSCIT) + if (id->flags & INPUT_DEVICE_ID_MATCH_MSCIT) do_input(alias, id->mscbit, 0, MSC_MAX); sprintf(alias + strlen(alias), "l*"); - if (id->flags&INPUT_DEVICE_ID_MATCH_LEDBIT) + if (id->flags & INPUT_DEVICE_ID_MATCH_LEDBIT) do_input(alias, id->ledbit, 0, LED_MAX); sprintf(alias + strlen(alias), "s*"); - if (id->flags&INPUT_DEVICE_ID_MATCH_SNDBIT) + if (id->flags & INPUT_DEVICE_ID_MATCH_SNDBIT) do_input(alias, id->sndbit, 0, SND_MAX); sprintf(alias + strlen(alias), "f*"); - if (id->flags&INPUT_DEVICE_ID_MATCH_FFBIT) + if (id->flags & INPUT_DEVICE_ID_MATCH_FFBIT) do_input(alias, id->ffbit, 0, FF_MAX); sprintf(alias + strlen(alias), "w*"); - if (id->flags&INPUT_DEVICE_ID_MATCH_SWBIT) + if (id->flags & INPUT_DEVICE_ID_MATCH_SWBIT) do_input(alias, id->swbit, 0, SW_MAX); return 1; } diff --git a/scripts/mod/modpost.c b/scripts/mod/modpost.c index cd00e9f0758..6d04504b2fc 100644 --- a/scripts/mod/modpost.c +++ b/scripts/mod/modpost.c @@ -487,14 +487,14 @@ static int strrcmp(const char *s, const char *sub) * atsym =__param* * * Pattern 2: - * Many drivers utilise a *_driver container with references to + * Many drivers utilise a *driver container with references to * add, remove, probe functions etc. * These functions may often be marked __init and we do not want to * warn here. * the pattern is identified by: * tosec = .init.text | .exit.text | .init.data * fromsec = .data - * atsym = *_driver, *_template, *_sht, *_ops, *_probe, *probe_one + * atsym = *driver, *_template, *_sht, *_ops, *_probe, *probe_one **/ static int secref_whitelist(const char *tosec, const char *fromsec, const char *atsym) @@ -502,7 +502,7 @@ static int secref_whitelist(const char *tosec, const char *fromsec, int f1 = 1, f2 = 1; const char **s; const char *pat2sym[] = { - "_driver", + "driver", "_template", /* scsi uses *_template a lot */ "_sht", /* scsi also used *_sht to some extent */ "_ops", diff --git a/security/dummy.c b/security/dummy.c index fd99429278e..8ccccccc12a 100644 --- a/security/dummy.c +++ b/security/dummy.c @@ -563,11 +563,6 @@ static int dummy_ipc_permission (struct kern_ipc_perm *ipcp, short flag) return 0; } -static int dummy_ipc_getsecurity(struct kern_ipc_perm *ipcp, void *buffer, size_t size) -{ - return -EOPNOTSUPP; -} - static int dummy_msg_msg_alloc_security (struct msg_msg *msg) { return 0; @@ -976,7 +971,6 @@ void security_fixup_ops (struct security_operations *ops) set_to_dummy_if_null(ops, task_reparent_to_init); set_to_dummy_if_null(ops, task_to_inode); set_to_dummy_if_null(ops, ipc_permission); - set_to_dummy_if_null(ops, ipc_getsecurity); set_to_dummy_if_null(ops, msg_msg_alloc_security); set_to_dummy_if_null(ops, msg_msg_free_security); set_to_dummy_if_null(ops, msg_queue_alloc_security); diff --git a/security/selinux/Makefile b/security/selinux/Makefile index 688c0a267b6..faf2e02e441 100644 --- a/security/selinux/Makefile +++ b/security/selinux/Makefile @@ -4,7 +4,7 @@ obj-$(CONFIG_SECURITY_SELINUX) := selinux.o ss/ -selinux-y := avc.o hooks.o selinuxfs.o netlink.o nlmsgtab.o netif.o +selinux-y := avc.o hooks.o selinuxfs.o netlink.o nlmsgtab.o netif.o exports.o selinux-$(CONFIG_SECURITY_NETWORK_XFRM) += xfrm.o diff --git a/security/selinux/avc.c b/security/selinux/avc.c index ac5d69bb337..a300702da52 100644 --- a/security/selinux/avc.c +++ b/security/selinux/avc.c @@ -800,7 +800,7 @@ out: int avc_ss_reset(u32 seqno) { struct avc_callback_node *c; - int i, rc = 0; + int i, rc = 0, tmprc; unsigned long flag; struct avc_node *node; @@ -813,15 +813,16 @@ int avc_ss_reset(u32 seqno) for (c = avc_callbacks; c; c = c->next) { if (c->events & AVC_CALLBACK_RESET) { - rc = c->callback(AVC_CALLBACK_RESET, - 0, 0, 0, 0, NULL); - if (rc) - goto out; + tmprc = c->callback(AVC_CALLBACK_RESET, + 0, 0, 0, 0, NULL); + /* save the first error encountered for the return + value and continue processing the callbacks */ + if (!rc) + rc = tmprc; } } avc_latest_notif_update(seqno, 0); -out: return rc; } diff --git a/security/selinux/exports.c b/security/selinux/exports.c new file mode 100644 index 00000000000..ae4c73eb308 --- /dev/null +++ b/security/selinux/exports.c @@ -0,0 +1,74 @@ +/* + * SELinux services exported to the rest of the kernel. + * + * Author: James Morris <jmorris@redhat.com> + * + * Copyright (C) 2005 Red Hat, Inc., James Morris <jmorris@redhat.com> + * Copyright (C) 2006 Trusted Computer Solutions, Inc. <dgoeddel@trustedcs.com> + * Copyright (C) 2006 IBM Corporation, Timothy R. Chavez <tinytim@us.ibm.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2, + * as published by the Free Software Foundation. + */ +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/selinux.h> +#include <linux/fs.h> +#include <linux/ipc.h> + +#include "security.h" +#include "objsec.h" + +void selinux_task_ctxid(struct task_struct *tsk, u32 *ctxid) +{ + struct task_security_struct *tsec = tsk->security; + if (selinux_enabled) + *ctxid = tsec->sid; + else + *ctxid = 0; +} + +int selinux_ctxid_to_string(u32 ctxid, char **ctx, u32 *ctxlen) +{ + if (selinux_enabled) + return security_sid_to_context(ctxid, ctx, ctxlen); + else { + *ctx = NULL; + *ctxlen = 0; + } + + return 0; +} + +void selinux_get_inode_sid(const struct inode *inode, u32 *sid) +{ + if (selinux_enabled) { + struct inode_security_struct *isec = inode->i_security; + *sid = isec->sid; + return; + } + *sid = 0; +} + +void selinux_get_ipc_sid(const struct kern_ipc_perm *ipcp, u32 *sid) +{ + if (selinux_enabled) { + struct ipc_security_struct *isec = ipcp->security; + *sid = isec->sid; + return; + } + *sid = 0; +} + +void selinux_get_task_sid(struct task_struct *tsk, u32 *sid) +{ + if (selinux_enabled) { + struct task_security_struct *tsec = tsk->security; + *sid = tsec->sid; + return; + } + *sid = 0; +} + diff --git a/security/selinux/hooks.c b/security/selinux/hooks.c index b61b9554bc2..d987048d3f3 100644 --- a/security/selinux/hooks.c +++ b/security/selinux/hooks.c @@ -101,6 +101,8 @@ static int __init selinux_enabled_setup(char *str) return 1; } __setup("selinux=", selinux_enabled_setup); +#else +int selinux_enabled = 1; #endif /* Original (dummy) security module. */ @@ -4052,13 +4054,6 @@ static int selinux_ipc_permission(struct kern_ipc_perm *ipcp, short flag) return ipc_has_perm(ipcp, av); } -static int selinux_ipc_getsecurity(struct kern_ipc_perm *ipcp, void *buffer, size_t size) -{ - struct ipc_security_struct *isec = ipcp->security; - - return selinux_getsecurity(isec->sid, buffer, size); -} - /* module stacking operations */ static int selinux_register_security (const char *name, struct security_operations *ops) { @@ -4321,7 +4316,6 @@ static struct security_operations selinux_ops = { .task_to_inode = selinux_task_to_inode, .ipc_permission = selinux_ipc_permission, - .ipc_getsecurity = selinux_ipc_getsecurity, .msg_msg_alloc_security = selinux_msg_msg_alloc_security, .msg_msg_free_security = selinux_msg_msg_free_security, @@ -4543,6 +4537,7 @@ int selinux_disable(void) printk(KERN_INFO "SELinux: Disabled at runtime.\n"); selinux_disabled = 1; + selinux_enabled = 0; /* Reset security_ops to the secondary module, dummy or capability. */ security_ops = secondary_ops; diff --git a/security/selinux/include/security.h b/security/selinux/include/security.h index 5f016c98056..063af47bb23 100644 --- a/security/selinux/include/security.h +++ b/security/selinux/include/security.h @@ -29,12 +29,7 @@ #define POLICYDB_VERSION_MIN POLICYDB_VERSION_BASE #define POLICYDB_VERSION_MAX POLICYDB_VERSION_AVTAB -#ifdef CONFIG_SECURITY_SELINUX_BOOTPARAM extern int selinux_enabled; -#else -#define selinux_enabled 1 -#endif - extern int selinux_mls_enabled; int security_load_policy(void * data, size_t len); diff --git a/security/selinux/ss/mls.c b/security/selinux/ss/mls.c index 84047f69f9c..7bc5b6440f7 100644 --- a/security/selinux/ss/mls.c +++ b/security/selinux/ss/mls.c @@ -8,7 +8,7 @@ * * Support for enhanced MLS infrastructure. * - * Copyright (C) 2004-2005 Trusted Computer Solutions, Inc. + * Copyright (C) 2004-2006 Trusted Computer Solutions, Inc. */ #include <linux/kernel.h> @@ -385,6 +385,34 @@ out: } /* + * Set the MLS fields in the security context structure + * `context' based on the string representation in + * the string `str'. This function will allocate temporary memory with the + * given constraints of gfp_mask. + */ +int mls_from_string(char *str, struct context *context, gfp_t gfp_mask) +{ + char *tmpstr, *freestr; + int rc; + + if (!selinux_mls_enabled) + return -EINVAL; + + /* we need freestr because mls_context_to_sid will change + the value of tmpstr */ + tmpstr = freestr = kstrdup(str, gfp_mask); + if (!tmpstr) { + rc = -ENOMEM; + } else { + rc = mls_context_to_sid(':', &tmpstr, context, + NULL, SECSID_NULL); + kfree(freestr); + } + + return rc; +} + +/* * Copies the effective MLS range from `src' into `dst'. */ static inline int mls_scopy_context(struct context *dst, diff --git a/security/selinux/ss/mls.h b/security/selinux/ss/mls.h index 03de697c805..fbb42f07dd7 100644 --- a/security/selinux/ss/mls.h +++ b/security/selinux/ss/mls.h @@ -8,7 +8,7 @@ * * Support for enhanced MLS infrastructure. * - * Copyright (C) 2004-2005 Trusted Computer Solutions, Inc. + * Copyright (C) 2004-2006 Trusted Computer Solutions, Inc. */ #ifndef _SS_MLS_H_ @@ -27,6 +27,8 @@ int mls_context_to_sid(char oldc, struct sidtab *s, u32 def_sid); +int mls_from_string(char *str, struct context *context, gfp_t gfp_mask); + int mls_convert_context(struct policydb *oldp, struct policydb *newp, struct context *context); diff --git a/security/selinux/ss/services.c b/security/selinux/ss/services.c index 61492485de8..7177e98df7f 100644 --- a/security/selinux/ss/services.c +++ b/security/selinux/ss/services.c @@ -7,12 +7,13 @@ * Updated: Trusted Computer Solutions, Inc. <dgoeddel@trustedcs.com> * * Support for enhanced MLS infrastructure. + * Support for context based audit filters. * * Updated: Frank Mayer <mayerf@tresys.com> and Karl MacMillan <kmacmillan@tresys.com> * * Added conditional policy language extensions * - * Copyright (C) 2004-2005 Trusted Computer Solutions, Inc. + * Copyright (C) 2004-2006 Trusted Computer Solutions, Inc. * Copyright (C) 2003 - 2004 Tresys Technology, LLC * Copyright (C) 2003 Red Hat, Inc., James Morris <jmorris@redhat.com> * This program is free software; you can redistribute it and/or modify @@ -1811,3 +1812,235 @@ out: POLICY_RDUNLOCK; return rc; } + +struct selinux_audit_rule { + u32 au_seqno; + struct context au_ctxt; +}; + +void selinux_audit_rule_free(struct selinux_audit_rule *rule) +{ + if (rule) { + context_destroy(&rule->au_ctxt); + kfree(rule); + } +} + +int selinux_audit_rule_init(u32 field, u32 op, char *rulestr, + struct selinux_audit_rule **rule) +{ + struct selinux_audit_rule *tmprule; + struct role_datum *roledatum; + struct type_datum *typedatum; + struct user_datum *userdatum; + int rc = 0; + + *rule = NULL; + + if (!ss_initialized) + return -ENOTSUPP; + + switch (field) { + case AUDIT_SE_USER: + case AUDIT_SE_ROLE: + case AUDIT_SE_TYPE: + /* only 'equals' and 'not equals' fit user, role, and type */ + if (op != AUDIT_EQUAL && op != AUDIT_NOT_EQUAL) + return -EINVAL; + break; + case AUDIT_SE_SEN: + case AUDIT_SE_CLR: + /* we do not allow a range, indicated by the presense of '-' */ + if (strchr(rulestr, '-')) + return -EINVAL; + break; + default: + /* only the above fields are valid */ + return -EINVAL; + } + + tmprule = kzalloc(sizeof(struct selinux_audit_rule), GFP_KERNEL); + if (!tmprule) + return -ENOMEM; + + context_init(&tmprule->au_ctxt); + + POLICY_RDLOCK; + + tmprule->au_seqno = latest_granting; + + switch (field) { + case AUDIT_SE_USER: + userdatum = hashtab_search(policydb.p_users.table, rulestr); + if (!userdatum) + rc = -EINVAL; + else + tmprule->au_ctxt.user = userdatum->value; + break; + case AUDIT_SE_ROLE: + roledatum = hashtab_search(policydb.p_roles.table, rulestr); + if (!roledatum) + rc = -EINVAL; + else + tmprule->au_ctxt.role = roledatum->value; + break; + case AUDIT_SE_TYPE: + typedatum = hashtab_search(policydb.p_types.table, rulestr); + if (!typedatum) + rc = -EINVAL; + else + tmprule->au_ctxt.type = typedatum->value; + break; + case AUDIT_SE_SEN: + case AUDIT_SE_CLR: + rc = mls_from_string(rulestr, &tmprule->au_ctxt, GFP_ATOMIC); + break; + } + + POLICY_RDUNLOCK; + + if (rc) { + selinux_audit_rule_free(tmprule); + tmprule = NULL; + } + + *rule = tmprule; + + return rc; +} + +int selinux_audit_rule_match(u32 ctxid, u32 field, u32 op, + struct selinux_audit_rule *rule, + struct audit_context *actx) +{ + struct context *ctxt; + struct mls_level *level; + int match = 0; + + if (!rule) { + audit_log(actx, GFP_ATOMIC, AUDIT_SELINUX_ERR, + "selinux_audit_rule_match: missing rule\n"); + return -ENOENT; + } + + POLICY_RDLOCK; + + if (rule->au_seqno < latest_granting) { + audit_log(actx, GFP_ATOMIC, AUDIT_SELINUX_ERR, + "selinux_audit_rule_match: stale rule\n"); + match = -ESTALE; + goto out; + } + + ctxt = sidtab_search(&sidtab, ctxid); + if (!ctxt) { + audit_log(actx, GFP_ATOMIC, AUDIT_SELINUX_ERR, + "selinux_audit_rule_match: unrecognized SID %d\n", + ctxid); + match = -ENOENT; + goto out; + } + + /* a field/op pair that is not caught here will simply fall through + without a match */ + switch (field) { + case AUDIT_SE_USER: + switch (op) { + case AUDIT_EQUAL: + match = (ctxt->user == rule->au_ctxt.user); + break; + case AUDIT_NOT_EQUAL: + match = (ctxt->user != rule->au_ctxt.user); + break; + } + break; + case AUDIT_SE_ROLE: + switch (op) { + case AUDIT_EQUAL: + match = (ctxt->role == rule->au_ctxt.role); + break; + case AUDIT_NOT_EQUAL: + match = (ctxt->role != rule->au_ctxt.role); + break; + } + break; + case AUDIT_SE_TYPE: + switch (op) { + case AUDIT_EQUAL: + match = (ctxt->type == rule->au_ctxt.type); + break; + case AUDIT_NOT_EQUAL: + match = (ctxt->type != rule->au_ctxt.type); + break; + } + break; + case AUDIT_SE_SEN: + case AUDIT_SE_CLR: + level = (op == AUDIT_SE_SEN ? + &ctxt->range.level[0] : &ctxt->range.level[1]); + switch (op) { + case AUDIT_EQUAL: + match = mls_level_eq(&rule->au_ctxt.range.level[0], + level); + break; + case AUDIT_NOT_EQUAL: + match = !mls_level_eq(&rule->au_ctxt.range.level[0], + level); + break; + case AUDIT_LESS_THAN: + match = (mls_level_dom(&rule->au_ctxt.range.level[0], + level) && + !mls_level_eq(&rule->au_ctxt.range.level[0], + level)); + break; + case AUDIT_LESS_THAN_OR_EQUAL: + match = mls_level_dom(&rule->au_ctxt.range.level[0], + level); + break; + case AUDIT_GREATER_THAN: + match = (mls_level_dom(level, + &rule->au_ctxt.range.level[0]) && + !mls_level_eq(level, + &rule->au_ctxt.range.level[0])); + break; + case AUDIT_GREATER_THAN_OR_EQUAL: + match = mls_level_dom(level, + &rule->au_ctxt.range.level[0]); + break; + } + } + +out: + POLICY_RDUNLOCK; + return match; +} + +static int (*aurule_callback)(void) = NULL; + +static int aurule_avc_callback(u32 event, u32 ssid, u32 tsid, + u16 class, u32 perms, u32 *retained) +{ + int err = 0; + + if (event == AVC_CALLBACK_RESET && aurule_callback) + err = aurule_callback(); + return err; +} + +static int __init aurule_init(void) +{ + int err; + + err = avc_add_callback(aurule_avc_callback, AVC_CALLBACK_RESET, + SECSID_NULL, SECSID_NULL, SECCLASS_NULL, 0); + if (err) + panic("avc_add_callback() failed, error %d\n", err); + + return err; +} +__initcall(aurule_init); + +void selinux_audit_set_callback(int (*callback)(void)) +{ + aurule_callback = callback; +} diff --git a/sound/core/Kconfig b/sound/core/Kconfig index 8efc1b12f3a..4262a1c8773 100644 --- a/sound/core/Kconfig +++ b/sound/core/Kconfig @@ -142,7 +142,7 @@ config SND_SUPPORT_OLD_API config SND_VERBOSE_PROCFS bool "Verbose procfs contents" - depends on SND + depends on SND && PROC_FS default y help Say Y here to include code for verbose procfs contents (provides @@ -171,3 +171,13 @@ config SND_DEBUG_DETECT help Say Y here to enable extra-verbose log messages printed when detecting devices. + +config SND_PCM_XRUN_DEBUG + bool "Enable PCM ring buffer overrun/underrun debugging" + default n + depends on SND_DEBUG && SND_VERBOSE_PROCFS + help + Say Y to enable the PCM ring buffer overrun/underrun debugging. + It is usually not required, but if you have trouble with + sound clicking when system is loaded, it may help to determine + the process or driver which causes the scheduling gaps. diff --git a/sound/core/oss/pcm_oss.c b/sound/core/oss/pcm_oss.c index c5978d6c608..ac990bf0b48 100644 --- a/sound/core/oss/pcm_oss.c +++ b/sound/core/oss/pcm_oss.c @@ -1242,6 +1242,8 @@ static int snd_pcm_oss_set_format(struct snd_pcm_oss_file *pcm_oss_file, int for if (format != AFMT_QUERY) { formats = snd_pcm_oss_get_formats(pcm_oss_file); + if (formats < 0) + return formats; if (!(formats & format)) format = AFMT_U8; for (idx = 1; idx >= 0; --idx) { @@ -2212,7 +2214,7 @@ static int snd_pcm_oss_mmap(struct file *file, struct vm_area_struct *area) return 0; } -#ifdef CONFIG_PROC_FS +#ifdef CONFIG_SND_VERBOSE_PROCFS /* * /proc interface */ @@ -2366,10 +2368,10 @@ static void snd_pcm_oss_proc_done(struct snd_pcm *pcm) } } } -#else /* !CONFIG_PROC_FS */ +#else /* !CONFIG_SND_VERBOSE_PROCFS */ #define snd_pcm_oss_proc_init(pcm) #define snd_pcm_oss_proc_done(pcm) -#endif /* CONFIG_PROC_FS */ +#endif /* CONFIG_SND_VERBOSE_PROCFS */ /* * ENTRY functions diff --git a/sound/core/pcm.c b/sound/core/pcm.c index 122e10a61ab..84b00038236 100644 --- a/sound/core/pcm.c +++ b/sound/core/pcm.c @@ -142,7 +142,7 @@ static int snd_pcm_control_ioctl(struct snd_card *card, return -ENOIOCTLCMD; } -#if defined(CONFIG_PROC_FS) && defined(CONFIG_SND_VERBOSE_PROCFS) +#ifdef CONFIG_SND_VERBOSE_PROCFS #define STATE(v) [SNDRV_PCM_STATE_##v] = #v #define STREAM(v) [SNDRV_PCM_STREAM_##v] = #v @@ -436,7 +436,7 @@ static void snd_pcm_substream_proc_status_read(struct snd_info_entry *entry, snd_iprintf(buffer, "appl_ptr : %ld\n", runtime->control->appl_ptr); } -#ifdef CONFIG_SND_DEBUG +#ifdef CONFIG_SND_PCM_XRUN_DEBUG static void snd_pcm_xrun_debug_read(struct snd_info_entry *entry, struct snd_info_buffer *buffer) { @@ -480,7 +480,7 @@ static int snd_pcm_stream_proc_init(struct snd_pcm_str *pstr) } pstr->proc_info_entry = entry; -#ifdef CONFIG_SND_DEBUG +#ifdef CONFIG_SND_PCM_XRUN_DEBUG if ((entry = snd_info_create_card_entry(pcm->card, "xrun_debug", pstr->proc_root)) != NULL) { entry->c.text.read_size = 64; @@ -501,7 +501,7 @@ static int snd_pcm_stream_proc_init(struct snd_pcm_str *pstr) static int snd_pcm_stream_proc_done(struct snd_pcm_str *pstr) { -#ifdef CONFIG_SND_DEBUG +#ifdef CONFIG_SND_PCM_XRUN_DEBUG if (pstr->proc_xrun_debug_entry) { snd_info_unregister(pstr->proc_xrun_debug_entry); pstr->proc_xrun_debug_entry = NULL; @@ -599,12 +599,12 @@ static int snd_pcm_substream_proc_done(struct snd_pcm_substream *substream) } return 0; } -#else /* !CONFIG_PROC_FS */ +#else /* !CONFIG_SND_VERBOSE_PROCFS */ static inline int snd_pcm_stream_proc_init(struct snd_pcm_str *pstr) { return 0; } static inline int snd_pcm_stream_proc_done(struct snd_pcm_str *pstr) { return 0; } static inline int snd_pcm_substream_proc_init(struct snd_pcm_substream *substream) { return 0; } static inline int snd_pcm_substream_proc_done(struct snd_pcm_substream *substream) { return 0; } -#endif /* CONFIG_PROC_FS */ +#endif /* CONFIG_SND_VERBOSE_PROCFS */ /** * snd_pcm_new_stream - create a new PCM stream diff --git a/sound/core/pcm_lib.c b/sound/core/pcm_lib.c index 230a940d00b..eedc6cb038b 100644 --- a/sound/core/pcm_lib.c +++ b/sound/core/pcm_lib.c @@ -130,7 +130,7 @@ void snd_pcm_playback_silence(struct snd_pcm_substream *substream, snd_pcm_ufram static void xrun(struct snd_pcm_substream *substream) { snd_pcm_stop(substream, SNDRV_PCM_STATE_XRUN); -#ifdef CONFIG_SND_DEBUG +#ifdef CONFIG_SND_PCM_XRUN_DEBUG if (substream->pstr->xrun_debug) { snd_printd(KERN_DEBUG "XRUN: pcmC%dD%d%c\n", substream->pcm->card->number, @@ -204,7 +204,7 @@ static inline int snd_pcm_update_hw_ptr_interrupt(struct snd_pcm_substream *subs delta = hw_ptr_interrupt - new_hw_ptr; if (delta > 0) { if ((snd_pcm_uframes_t)delta < runtime->buffer_size / 2) { -#ifdef CONFIG_SND_DEBUG +#ifdef CONFIG_SND_PCM_XRUN_DEBUG if (runtime->periods > 1 && substream->pstr->xrun_debug) { snd_printd(KERN_ERR "Unexpected hw_pointer value [1] (stream = %i, delta: -%ld, max jitter = %ld): wrong interrupt acknowledge?\n", substream->stream, (long) delta, runtime->buffer_size / 2); if (substream->pstr->xrun_debug > 1) @@ -249,7 +249,7 @@ int snd_pcm_update_hw_ptr(struct snd_pcm_substream *substream) delta = old_hw_ptr - new_hw_ptr; if (delta > 0) { if ((snd_pcm_uframes_t)delta < runtime->buffer_size / 2) { -#ifdef CONFIG_SND_DEBUG +#ifdef CONFIG_SND_PCM_XRUN_DEBUG if (runtime->periods > 2 && substream->pstr->xrun_debug) { snd_printd(KERN_ERR "Unexpected hw_pointer value [2] (stream = %i, delta: -%ld, max jitter = %ld): wrong interrupt acknowledge?\n", substream->stream, (long) delta, runtime->buffer_size / 2); if (substream->pstr->xrun_debug > 1) diff --git a/sound/core/pcm_memory.c b/sound/core/pcm_memory.c index a0119ae67dc..428f8c169ee 100644 --- a/sound/core/pcm_memory.c +++ b/sound/core/pcm_memory.c @@ -100,8 +100,10 @@ static void snd_pcm_lib_preallocate_dma_free(struct snd_pcm_substream *substream int snd_pcm_lib_preallocate_free(struct snd_pcm_substream *substream) { snd_pcm_lib_preallocate_dma_free(substream); +#ifdef CONFIG_SND_VERBOSE_PROCFS snd_info_unregister(substream->proc_prealloc_entry); substream->proc_prealloc_entry = NULL; +#endif return 0; } @@ -124,7 +126,7 @@ int snd_pcm_lib_preallocate_free_for_all(struct snd_pcm *pcm) return 0; } -#ifdef CONFIG_PROC_FS +#ifdef CONFIG_SND_VERBOSE_PROCFS /* * read callback for prealloc proc file * @@ -203,9 +205,9 @@ static inline void preallocate_info_init(struct snd_pcm_substream *substream) substream->proc_prealloc_entry = entry; } -#else /* !CONFIG_PROC_FS */ +#else /* !CONFIG_SND_VERBOSE_PROCFS */ #define preallocate_info_init(s) -#endif +#endif /* CONFIG_SND_VERBOSE_PROCFS */ /* * pre-allocate the buffer and create a proc file for the substream diff --git a/sound/drivers/dummy.c b/sound/drivers/dummy.c index e35fd5779a9..ae0df549fac 100644 --- a/sound/drivers/dummy.c +++ b/sound/drivers/dummy.c @@ -675,10 +675,8 @@ static int __init alsa_card_dummy_init(void) continue; device = platform_device_register_simple(SND_DUMMY_DRIVER, i, NULL, 0); - if (IS_ERR(device)) { - err = PTR_ERR(device); - goto errout; - } + if (IS_ERR(device)) + continue; devices[i] = device; cards++; } @@ -686,14 +684,10 @@ static int __init alsa_card_dummy_init(void) #ifdef MODULE printk(KERN_ERR "Dummy soundcard not found or device busy\n"); #endif - err = -ENODEV; - goto errout; + snd_dummy_unregister_all(); + return -ENODEV; } return 0; - - errout: - snd_dummy_unregister_all(); - return err; } static void __exit alsa_card_dummy_exit(void) diff --git a/sound/drivers/mpu401/mpu401.c b/sound/drivers/mpu401/mpu401.c index 9ea3059a706..da7ef26995c 100644 --- a/sound/drivers/mpu401/mpu401.c +++ b/sound/drivers/mpu401/mpu401.c @@ -251,10 +251,8 @@ static int __init alsa_card_mpu401_init(void) #endif device = platform_device_register_simple(SND_MPU401_DRIVER, i, NULL, 0); - if (IS_ERR(device)) { - err = PTR_ERR(device); - goto errout; - } + if (IS_ERR(device)) + continue; platform_devices[i] = device; snd_mpu401_devices++; } @@ -266,14 +264,10 @@ static int __init alsa_card_mpu401_init(void) #ifdef MODULE printk(KERN_ERR "MPU-401 device not found or device busy\n"); #endif - err = -ENODEV; - goto errout; + snd_mpu401_unregister_all(); + return -ENODEV; } return 0; - - errout: - snd_mpu401_unregister_all(); - return err; } static void __exit alsa_card_mpu401_exit(void) diff --git a/sound/drivers/serial-u16550.c b/sound/drivers/serial-u16550.c index 1a7fbefe474..c01b4c5118b 100644 --- a/sound/drivers/serial-u16550.c +++ b/sound/drivers/serial-u16550.c @@ -996,10 +996,8 @@ static int __init alsa_card_serial_init(void) continue; device = platform_device_register_simple(SND_SERIAL_DRIVER, i, NULL, 0); - if (IS_ERR(device)) { - err = PTR_ERR(device); - goto errout; - } + if (IS_ERR(device)) + continue; devices[i] = device; cards++; } @@ -1007,14 +1005,10 @@ static int __init alsa_card_serial_init(void) #ifdef MODULE printk(KERN_ERR "serial midi soundcard not found or device busy\n"); #endif - err = -ENODEV; - goto errout; + snd_serial_unregister_all(); + return -ENODEV; } return 0; - - errout: - snd_serial_unregister_all(); - return err; } static void __exit alsa_card_serial_exit(void) diff --git a/sound/drivers/virmidi.c b/sound/drivers/virmidi.c index a3ee306239c..26eb2499d44 100644 --- a/sound/drivers/virmidi.c +++ b/sound/drivers/virmidi.c @@ -169,10 +169,8 @@ static int __init alsa_card_virmidi_init(void) continue; device = platform_device_register_simple(SND_VIRMIDI_DRIVER, i, NULL, 0); - if (IS_ERR(device)) { - err = PTR_ERR(device); - goto errout; - } + if (IS_ERR(device)) + continue; devices[i] = device; cards++; } @@ -180,14 +178,10 @@ static int __init alsa_card_virmidi_init(void) #ifdef MODULE printk(KERN_ERR "Card-VirMIDI soundcard not found or device busy\n"); #endif - err = -ENODEV; - goto errout; + snd_virmidi_unregister_all(); + return -ENODEV; } return 0; - - errout: - snd_virmidi_unregister_all(); - return err; } static void __exit alsa_card_virmidi_exit(void) diff --git a/sound/isa/opti9xx/miro.c b/sound/isa/opti9xx/miro.c index 83d64bc07ff..e6bfcf74c1c 100644 --- a/sound/isa/opti9xx/miro.c +++ b/sound/isa/opti9xx/miro.c @@ -1179,20 +1179,17 @@ static int __init snd_card_miro_aci_detect(struct snd_card *card, struct snd_mir /* force ACI into a known state */ for (i = 0; i < 3; i++) if (aci_cmd(miro, ACI_ERROR_OP, -1, -1) < 0) { - snd_card_free(card); snd_printk(KERN_ERR "can't force aci into known state.\n"); return -ENXIO; } if ((miro->aci_vendor=aci_cmd(miro, ACI_READ_IDCODE, -1, -1)) < 0 || (miro->aci_product=aci_cmd(miro, ACI_READ_IDCODE, -1, -1)) < 0) { - snd_card_free(card); snd_printk(KERN_ERR "can't read aci id on 0x%lx.\n", miro->aci_port); return -ENXIO; } if ((miro->aci_version=aci_cmd(miro, ACI_READ_VERSION, -1, -1)) < 0) { - snd_card_free(card); snd_printk(KERN_ERR "can't read aci version on 0x%lx.\n", miro->aci_port); return -ENXIO; diff --git a/sound/oss/Kconfig b/sound/oss/Kconfig index 6275266dde2..558c6ed443b 100644 --- a/sound/oss/Kconfig +++ b/sound/oss/Kconfig @@ -478,6 +478,20 @@ config SOUND_ACI_MIXER This driver is also available as a module and will be called aci. +config SOUND_CS4232 + tristate "Crystal CS4232 based (PnP) cards" + depends on SOUND_OSS + help + Say Y here if you have a card based on the Crystal CS4232 chip set, + which uses its own Plug and Play protocol. + + If you compile the driver into the kernel, you have to add + "cs4232=<io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>" to the kernel + command line. + + See <file:Documentation/sound/oss/CS4232> for more information on + configuring this card. + config SOUND_VMIDI tristate "Loopback MIDI device support" depends on SOUND_OSS diff --git a/sound/pci/ad1889.c b/sound/pci/ad1889.c index c6c8333acc6..eece1c7e55a 100644 --- a/sound/pci/ad1889.c +++ b/sound/pci/ad1889.c @@ -39,7 +39,6 @@ #include <linux/interrupt.h> #include <linux/compiler.h> #include <linux/delay.h> -#include <linux/dma-mapping.h> #include <sound/driver.h> #include <sound/core.h> @@ -1052,7 +1051,7 @@ snd_ad1889_remove(struct pci_dev *pci) pci_set_drvdata(pci, NULL); } -static struct pci_device_id snd_ad1889_ids[] = { +static struct pci_device_id snd_ad1889_ids[] __devinitdata = { { PCI_DEVICE(PCI_VENDOR_ID_ANALOG_DEVICES, PCI_DEVICE_ID_AD1889JS) }, { 0, }, }; diff --git a/sound/pci/ali5451/ali5451.c b/sound/pci/ali5451/ali5451.c index fc92b6896c2..e2dbc211890 100644 --- a/sound/pci/ali5451/ali5451.c +++ b/sound/pci/ali5451/ali5451.c @@ -279,7 +279,7 @@ struct snd_ali { #endif }; -static struct pci_device_id snd_ali_ids[] = { +static struct pci_device_id snd_ali_ids[] __devinitdata = { {PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5451), 0, 0, 0}, {0, } }; diff --git a/sound/pci/als300.c b/sound/pci/als300.c index 91899f87f03..901b08ae917 100644 --- a/sound/pci/als300.c +++ b/sound/pci/als300.c @@ -146,7 +146,7 @@ struct snd_als300_substream_data { int block_counter_register; }; -static struct pci_device_id snd_als300_ids[] = { +static struct pci_device_id snd_als300_ids[] __devinitdata = { { 0x4005, 0x0300, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DEVICE_ALS300 }, { 0x4005, 0x0308, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DEVICE_ALS300_PLUS }, { 0, } diff --git a/sound/pci/als4000.c b/sound/pci/als4000.c index 100d8127a41..60423b1c678 100644 --- a/sound/pci/als4000.c +++ b/sound/pci/als4000.c @@ -116,7 +116,7 @@ struct snd_card_als4000 { #endif }; -static struct pci_device_id snd_als4000_ids[] = { +static struct pci_device_id snd_als4000_ids[] __devinitdata = { { 0x4005, 0x4000, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, /* ALS4000 */ { 0, } }; diff --git a/sound/pci/atiixp.c b/sound/pci/atiixp.c index 12e61885126..d0f759d86d3 100644 --- a/sound/pci/atiixp.c +++ b/sound/pci/atiixp.c @@ -284,7 +284,7 @@ struct atiixp { /* */ -static struct pci_device_id snd_atiixp_ids[] = { +static struct pci_device_id snd_atiixp_ids[] __devinitdata = { { 0x1002, 0x4341, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, /* SB200 */ { 0x1002, 0x4361, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, /* SB300 */ { 0x1002, 0x4370, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, /* SB400 */ diff --git a/sound/pci/atiixp_modem.c b/sound/pci/atiixp_modem.c index 1d376604464..12a34c39caa 100644 --- a/sound/pci/atiixp_modem.c +++ b/sound/pci/atiixp_modem.c @@ -262,7 +262,7 @@ struct atiixp_modem { /* */ -static struct pci_device_id snd_atiixp_ids[] = { +static struct pci_device_id snd_atiixp_ids[] __devinitdata = { { 0x1002, 0x434d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, /* SB200 */ { 0x1002, 0x4378, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, /* SB400 */ { 0, } diff --git a/sound/pci/au88x0/au8810.c b/sound/pci/au88x0/au8810.c index fce22c7af0e..bd3352998ad 100644 --- a/sound/pci/au88x0/au8810.c +++ b/sound/pci/au88x0/au8810.c @@ -1,6 +1,6 @@ #include "au8810.h" #include "au88x0.h" -static struct pci_device_id snd_vortex_ids[] = { +static struct pci_device_id snd_vortex_ids[] __devinitdata = { {PCI_VENDOR_ID_AUREAL, PCI_DEVICE_ID_AUREAL_ADVANTAGE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1,}, {0,} diff --git a/sound/pci/au88x0/au8820.c b/sound/pci/au88x0/au8820.c index d1fbcce0725..7e3fd8372d8 100644 --- a/sound/pci/au88x0/au8820.c +++ b/sound/pci/au88x0/au8820.c @@ -1,6 +1,6 @@ #include "au8820.h" #include "au88x0.h" -static struct pci_device_id snd_vortex_ids[] = { +static struct pci_device_id snd_vortex_ids[] __devinitdata = { {PCI_VENDOR_ID_AUREAL, PCI_DEVICE_ID_AUREAL_VORTEX_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0,}, {0,} diff --git a/sound/pci/au88x0/au8830.c b/sound/pci/au88x0/au8830.c index d4f2717c14f..b840f6608a6 100644 --- a/sound/pci/au88x0/au8830.c +++ b/sound/pci/au88x0/au8830.c @@ -1,6 +1,6 @@ #include "au8830.h" #include "au88x0.h" -static struct pci_device_id snd_vortex_ids[] = { +static struct pci_device_id snd_vortex_ids[] __devinitdata = { {PCI_VENDOR_ID_AUREAL, PCI_DEVICE_ID_AUREAL_VORTEX_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0,}, {0,} diff --git a/sound/pci/azt3328.c b/sound/pci/azt3328.c index 680077e1e05..52a36452426 100644 --- a/sound/pci/azt3328.c +++ b/sound/pci/azt3328.c @@ -216,7 +216,7 @@ struct snd_azf3328 { int irq; }; -static const struct pci_device_id snd_azf3328_ids[] = { +static const struct pci_device_id snd_azf3328_ids[] __devinitdata = { { 0x122D, 0x50DC, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, /* PCI168/3328 */ { 0x122D, 0x80DA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, /* 3328 */ { 0, } diff --git a/sound/pci/bt87x.c b/sound/pci/bt87x.c index 7b44a8db033..9ee07d4aac1 100644 --- a/sound/pci/bt87x.c +++ b/sound/pci/bt87x.c @@ -774,7 +774,7 @@ static int __devinit snd_bt87x_create(struct snd_card *card, .driver_data = rate } /* driver_data is the default digital_rate value for that device */ -static struct pci_device_id snd_bt87x_ids[] = { +static struct pci_device_id snd_bt87x_ids[] __devinitdata = { /* Hauppauge WinTV series */ BT_DEVICE(PCI_DEVICE_ID_BROOKTREE_878, 0x0070, 0x13eb, 32000), /* Hauppauge WinTV series */ @@ -911,7 +911,7 @@ static void __devexit snd_bt87x_remove(struct pci_dev *pci) /* default entries for all Bt87x cards - it's not exported */ /* driver_data is set to 0 to call detection */ -static struct pci_device_id snd_bt87x_default_ids[] = { +static struct pci_device_id snd_bt87x_default_ids[] __devinitdata = { BT_DEVICE(PCI_DEVICE_ID_BROOKTREE_878, PCI_ANY_ID, PCI_ANY_ID, 0), BT_DEVICE(PCI_DEVICE_ID_BROOKTREE_879, PCI_ANY_ID, PCI_ANY_ID, 0), { } diff --git a/sound/pci/ca0106/ca0106_main.c b/sound/pci/ca0106/ca0106_main.c index 9477838a9c8..fd8bfebfbd5 100644 --- a/sound/pci/ca0106/ca0106_main.c +++ b/sound/pci/ca0106/ca0106_main.c @@ -1561,7 +1561,7 @@ static void __devexit snd_ca0106_remove(struct pci_dev *pci) } // PCI IDs -static struct pci_device_id snd_ca0106_ids[] = { +static struct pci_device_id snd_ca0106_ids[] __devinitdata = { { 0x1102, 0x0007, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, /* Audigy LS or Live 24bit */ { 0, } }; diff --git a/sound/pci/cmipci.c b/sound/pci/cmipci.c index 2ecbddbbdcf..e5ce2dabd08 100644 --- a/sound/pci/cmipci.c +++ b/sound/pci/cmipci.c @@ -2609,7 +2609,7 @@ static inline void snd_cmipci_proc_init(struct cmipci *cm) {} #endif -static struct pci_device_id snd_cmipci_ids[] = { +static struct pci_device_id snd_cmipci_ids[] __devinitdata = { {PCI_VENDOR_ID_CMEDIA, PCI_DEVICE_ID_CMEDIA_CM8338A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, {PCI_VENDOR_ID_CMEDIA, PCI_DEVICE_ID_CMEDIA_CM8338B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, {PCI_VENDOR_ID_CMEDIA, PCI_DEVICE_ID_CMEDIA_CM8738, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, diff --git a/sound/pci/cs4281.c b/sound/pci/cs4281.c index ac4e73f69c1..b3c94d83450 100644 --- a/sound/pci/cs4281.c +++ b/sound/pci/cs4281.c @@ -494,7 +494,7 @@ struct cs4281 { static irqreturn_t snd_cs4281_interrupt(int irq, void *dev_id, struct pt_regs *regs); -static struct pci_device_id snd_cs4281_ids[] = { +static struct pci_device_id snd_cs4281_ids[] __devinitdata = { { 0x1013, 0x6005, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, /* CS4281 */ { 0, } }; diff --git a/sound/pci/cs46xx/cs46xx.c b/sound/pci/cs46xx/cs46xx.c index c590602e20c..848d772ae3c 100644 --- a/sound/pci/cs46xx/cs46xx.c +++ b/sound/pci/cs46xx/cs46xx.c @@ -65,7 +65,7 @@ MODULE_PARM_DESC(thinkpad, "Force to enable Thinkpad's CLKRUN control."); module_param_array(mmap_valid, bool, NULL, 0444); MODULE_PARM_DESC(mmap_valid, "Support OSS mmap."); -static struct pci_device_id snd_cs46xx_ids[] = { +static struct pci_device_id snd_cs46xx_ids[] __devinitdata = { { 0x1013, 0x6001, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, /* CS4280 */ { 0x1013, 0x6003, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, /* CS4612 */ { 0x1013, 0x6004, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, /* CS4615 */ diff --git a/sound/pci/cs5535audio/cs5535audio.c b/sound/pci/cs5535audio/cs5535audio.c index 9fc7f382746..2c1213a35dc 100644 --- a/sound/pci/cs5535audio/cs5535audio.c +++ b/sound/pci/cs5535audio/cs5535audio.c @@ -45,7 +45,7 @@ static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX; static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR; static int enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE_PNP; -static struct pci_device_id snd_cs5535audio_ids[] = { +static struct pci_device_id snd_cs5535audio_ids[] __devinitdata = { { PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_CS5535_AUDIO, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_AUDIO, diff --git a/sound/pci/emu10k1/emu10k1.c b/sound/pci/emu10k1/emu10k1.c index 2dfa932f782..42b11ba1d21 100644 --- a/sound/pci/emu10k1/emu10k1.c +++ b/sound/pci/emu10k1/emu10k1.c @@ -77,7 +77,7 @@ MODULE_PARM_DESC(subsystem, "Force card subsystem model."); /* * Class 0401: 1102:0008 (rev 00) Subsystem: 1102:1001 -> Audigy2 Value Model:SB0400 */ -static struct pci_device_id snd_emu10k1_ids[] = { +static struct pci_device_id snd_emu10k1_ids[] __devinitdata = { { 0x1102, 0x0002, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, /* EMU10K1 */ { 0x1102, 0x0004, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1 }, /* Audigy */ { 0x1102, 0x0008, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1 }, /* Audigy 2 Value SB0400 */ diff --git a/sound/pci/emu10k1/emu10k1x.c b/sound/pci/emu10k1/emu10k1x.c index 3e332f39816..d51290c1816 100644 --- a/sound/pci/emu10k1/emu10k1x.c +++ b/sound/pci/emu10k1/emu10k1x.c @@ -36,7 +36,6 @@ #include <linux/dma-mapping.h> #include <linux/slab.h> #include <linux/moduleparam.h> -#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/initval.h> #include <sound/pcm.h> @@ -1596,7 +1595,7 @@ static void __devexit snd_emu10k1x_remove(struct pci_dev *pci) } // PCI IDs -static struct pci_device_id snd_emu10k1x_ids[] = { +static struct pci_device_id snd_emu10k1x_ids[] __devinitdata = { { 0x1102, 0x0006, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, /* Dell OEM version (EMU10K1) */ { 0, } }; diff --git a/sound/pci/ens1370.c b/sound/pci/ens1370.c index a5533c86b0b..ca9e34e88f6 100644 --- a/sound/pci/ens1370.c +++ b/sound/pci/ens1370.c @@ -446,7 +446,7 @@ struct ensoniq { static irqreturn_t snd_audiopci_interrupt(int irq, void *dev_id, struct pt_regs *regs); -static struct pci_device_id snd_audiopci_ids[] = { +static struct pci_device_id snd_audiopci_ids[] __devinitdata = { #ifdef CHIP1370 { 0x1274, 0x5000, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, /* ES1370 */ #endif diff --git a/sound/pci/es1938.c b/sound/pci/es1938.c index 4d62fe43917..6f9094ca4fb 100644 --- a/sound/pci/es1938.c +++ b/sound/pci/es1938.c @@ -242,7 +242,7 @@ struct es1938 { static irqreturn_t snd_es1938_interrupt(int irq, void *dev_id, struct pt_regs *regs); -static struct pci_device_id snd_es1938_ids[] = { +static struct pci_device_id snd_es1938_ids[] __devinitdata = { { 0x125d, 0x1969, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, /* Solo-1 */ { 0, } }; diff --git a/sound/pci/es1968.c b/sound/pci/es1968.c index e3ad17f53c2..5ff4175c7b6 100644 --- a/sound/pci/es1968.c +++ b/sound/pci/es1968.c @@ -104,7 +104,6 @@ #include <linux/slab.h> #include <linux/gameport.h> #include <linux/moduleparam.h> -#include <linux/dma-mapping.h> #include <linux/mutex.h> #include <sound/core.h> @@ -593,7 +592,7 @@ struct es1968 { static irqreturn_t snd_es1968_interrupt(int irq, void *dev_id, struct pt_regs *regs); -static struct pci_device_id snd_es1968_ids[] = { +static struct pci_device_id snd_es1968_ids[] __devinitdata = { /* Maestro 1 */ { 0x1285, 0x0100, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_MULTIMEDIA_AUDIO << 8, 0xffff00, TYPE_MAESTRO }, /* Maestro 2 */ diff --git a/sound/pci/fm801.c b/sound/pci/fm801.c index 6ab4aefbccf..d72fc28c580 100644 --- a/sound/pci/fm801.c +++ b/sound/pci/fm801.c @@ -199,7 +199,7 @@ struct fm801 { #endif }; -static struct pci_device_id snd_fm801_ids[] = { +static struct pci_device_id snd_fm801_ids[] __devinitdata = { { 0x1319, 0x0801, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_MULTIMEDIA_AUDIO << 8, 0xffff00, 0, }, /* FM801 */ { 0x5213, 0x0510, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_MULTIMEDIA_AUDIO << 8, 0xffff00, 0, }, /* Gallant Odyssey Sound 4 */ { 0, } diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index 0ad60ae2901..e821d65afa1 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -1614,7 +1614,7 @@ static void __devexit azx_remove(struct pci_dev *pci) } /* PCI IDs */ -static struct pci_device_id azx_ids[] = { +static struct pci_device_id azx_ids[] __devinitdata = { { 0x8086, 0x2668, PCI_ANY_ID, PCI_ANY_ID, 0, 0, AZX_DRIVER_ICH }, /* ICH6 */ { 0x8086, 0x27d8, PCI_ANY_ID, PCI_ANY_ID, 0, 0, AZX_DRIVER_ICH }, /* ICH7 */ { 0x8086, 0x269a, PCI_ANY_ID, PCI_ANY_ID, 0, 0, AZX_DRIVER_ICH }, /* ESB2 */ diff --git a/sound/pci/hda/patch_analog.c b/sound/pci/hda/patch_analog.c index bcfca159c6a..40f000ba136 100644 --- a/sound/pci/hda/patch_analog.c +++ b/sound/pci/hda/patch_analog.c @@ -799,10 +799,14 @@ static struct hda_board_config ad1986a_cfg_tbl[] = { { .modelname = "laptop-eapd", .config = AD1986A_LAPTOP_EAPD }, { .pci_subvendor = 0x144d, .pci_subdevice = 0xc024, .config = AD1986A_LAPTOP_EAPD }, /* Samsung R65-T2300 Charis */ + { .pci_subvendor = 0x1043, .pci_subdevice = 0x1153, + .config = AD1986A_LAPTOP_EAPD }, /* ASUS M9 */ { .pci_subvendor = 0x1043, .pci_subdevice = 0x1213, .config = AD1986A_LAPTOP_EAPD }, /* ASUS A6J */ { .pci_subvendor = 0x1043, .pci_subdevice = 0x11f7, .config = AD1986A_LAPTOP_EAPD }, /* ASUS U5A */ + { .pci_subvendor = 0x1043, .pci_subdevice = 0x1297, + .config = AD1986A_LAPTOP_EAPD }, /* ASUS Z62F */ { .pci_subvendor = 0x103c, .pci_subdevice = 0x30af, .config = AD1986A_LAPTOP_EAPD }, /* HP Compaq Presario B2800 */ {} @@ -1330,12 +1334,8 @@ enum { AD1981_BASIC, AD1981_HP }; static struct hda_board_config ad1981_cfg_tbl[] = { { .modelname = "hp", .config = AD1981_HP }, - { .pci_subvendor = 0x103c, .pci_subdevice = 0x30aa, - .config = AD1981_HP }, /* HP nx6320 */ - { .pci_subvendor = 0x103c, .pci_subdevice = 0x309f, - .config = AD1981_HP }, /* HP nx9420 AngelFire */ - { .pci_subvendor = 0x103c, .pci_subdevice = 0x30a2, - .config = AD1981_HP }, /* HP nx9420 AngelFire */ + /* All HP models */ + { .pci_subvendor = 0x103c, .config = AD1981_HP }, { .modelname = "basic", .config = AD1981_BASIC }, {} }; @@ -2623,5 +2623,6 @@ struct hda_codec_preset snd_hda_preset_analog[] = { { .id = 0x11d41983, .name = "AD1983", .patch = patch_ad1983 }, { .id = 0x11d41986, .name = "AD1986A", .patch = patch_ad1986a }, { .id = 0x11d41988, .name = "AD1988", .patch = patch_ad1988 }, + { .id = 0x11d4198b, .name = "AD1988B", .patch = patch_ad1988 }, {} /* terminator */ }; diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 66bbdb60f50..f0e9a9c9078 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -2148,6 +2148,7 @@ static struct hda_board_config alc880_cfg_tbl[] = { { .pci_subvendor = 0x1025, .pci_subdevice = 0x0087, .config = ALC880_6ST_DIG }, { .pci_subvendor = 0x1297, .pci_subdevice = 0xc790, .config = ALC880_6ST_DIG }, /* Shuttle ST20G5 */ { .pci_subvendor = 0x1509, .pci_subdevice = 0x925d, .config = ALC880_6ST_DIG }, /* FIC P4M-915GD1 */ + { .pci_subvendor = 0x1695, .pci_subdevice = 0x4012, .config = ALC880_5ST_DIG }, /* Epox EP-5LDA+ GLi */ { .modelname = "asus", .config = ALC880_ASUS }, { .pci_subvendor = 0x1043, .pci_subdevice = 0x1964, .config = ALC880_ASUS_DIG }, diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c index 71526078795..8c440fb9860 100644 --- a/sound/pci/hda/patch_sigmatel.c +++ b/sound/pci/hda/patch_sigmatel.c @@ -1212,8 +1212,8 @@ static hda_nid_t vaio_mux_nids[] = { 0x15 }; static struct hda_input_mux vaio_mux = { .num_items = 2, .items = { - /* { "HP", 0x0 }, - { "Unknown", 0x1 }, */ + /* { "HP", 0x0 }, */ + { "Line", 0x1 }, { "Mic", 0x2 }, { "PCM", 0x3 }, } diff --git a/sound/pci/ice1712/ice1712.c b/sound/pci/ice1712/ice1712.c index 32f8415558a..c56793b381e 100644 --- a/sound/pci/ice1712/ice1712.c +++ b/sound/pci/ice1712/ice1712.c @@ -56,7 +56,6 @@ #include <linux/dma-mapping.h> #include <linux/slab.h> #include <linux/moduleparam.h> -#include <linux/dma-mapping.h> #include <linux/mutex.h> #include <sound/core.h> @@ -108,7 +107,7 @@ module_param_array(dxr_enable, int, NULL, 0444); MODULE_PARM_DESC(dxr_enable, "Enable DXR support for Terratec DMX6FIRE."); -static struct pci_device_id snd_ice1712_ids[] = { +static struct pci_device_id snd_ice1712_ids[] __devinitdata = { { PCI_VENDOR_ID_ICE, PCI_DEVICE_ID_ICE_1712, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, /* ICE1712 */ { 0, } }; diff --git a/sound/pci/ice1712/ice1724.c b/sound/pci/ice1712/ice1724.c index fce616c2761..b1c007e022d 100644 --- a/sound/pci/ice1712/ice1724.c +++ b/sound/pci/ice1712/ice1724.c @@ -86,7 +86,7 @@ MODULE_PARM_DESC(model, "Use the given board model."); /* Both VT1720 and VT1724 have the same PCI IDs */ -static struct pci_device_id snd_vt1724_ids[] = { +static struct pci_device_id snd_vt1724_ids[] __devinitdata = { { PCI_VENDOR_ID_ICE, PCI_DEVICE_ID_VT1724, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, { 0, } }; diff --git a/sound/pci/intel8x0.c b/sound/pci/intel8x0.c index ebbf2cf4ca0..0df7602568e 100644 --- a/sound/pci/intel8x0.c +++ b/sound/pci/intel8x0.c @@ -413,7 +413,7 @@ struct intel8x0 { u32 int_sta_mask; /* interrupt status mask */ }; -static struct pci_device_id snd_intel8x0_ids[] = { +static struct pci_device_id snd_intel8x0_ids[] __devinitdata = { { 0x8086, 0x2415, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DEVICE_INTEL }, /* 82801AA */ { 0x8086, 0x2425, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DEVICE_INTEL }, /* 82901AB */ { 0x8086, 0x2445, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DEVICE_INTEL }, /* 82801BA */ @@ -1293,6 +1293,7 @@ static int snd_intel8x0_ali_ac97spdifout_close(struct snd_pcm_substream *substre return 0; } +#if 0 // NYI static int snd_intel8x0_ali_spdifin_open(struct snd_pcm_substream *substream) { struct intel8x0 *chip = snd_pcm_substream_chip(substream); @@ -1308,7 +1309,6 @@ static int snd_intel8x0_ali_spdifin_close(struct snd_pcm_substream *substream) return 0; } -#if 0 // NYI static int snd_intel8x0_ali_spdifout_open(struct snd_pcm_substream *substream) { struct intel8x0 *chip = snd_pcm_substream_chip(substream); @@ -1435,6 +1435,7 @@ static struct snd_pcm_ops snd_intel8x0_ali_ac97spdifout_ops = { .pointer = snd_intel8x0_pcm_pointer, }; +#if 0 // NYI static struct snd_pcm_ops snd_intel8x0_ali_spdifin_ops = { .open = snd_intel8x0_ali_spdifin_open, .close = snd_intel8x0_ali_spdifin_close, @@ -1446,7 +1447,6 @@ static struct snd_pcm_ops snd_intel8x0_ali_spdifin_ops = { .pointer = snd_intel8x0_pcm_pointer, }; -#if 0 // NYI static struct snd_pcm_ops snd_intel8x0_ali_spdifout_ops = { .open = snd_intel8x0_ali_spdifout_open, .close = snd_intel8x0_ali_spdifout_close, @@ -1582,7 +1582,7 @@ static struct ich_pcm_table ali_pcms[] __devinitdata = { { .suffix = "IEC958", .playback_ops = &snd_intel8x0_ali_ac97spdifout_ops, - .capture_ops = &snd_intel8x0_ali_spdifin_ops, + /* .capture_ops = &snd_intel8x0_ali_spdifin_ops, */ .prealloc_size = 64 * 1024, .prealloc_max_size = 128 * 1024, .ac97_idx = ALID_AC97SPDIFOUT, diff --git a/sound/pci/intel8x0m.c b/sound/pci/intel8x0m.c index 47e26aaa9ad..720635f0cb8 100644 --- a/sound/pci/intel8x0m.c +++ b/sound/pci/intel8x0m.c @@ -224,7 +224,7 @@ struct intel8x0m { unsigned int pcm_pos_shift; }; -static struct pci_device_id snd_intel8x0m_ids[] = { +static struct pci_device_id snd_intel8x0m_ids[] __devinitdata = { { 0x8086, 0x2416, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DEVICE_INTEL }, /* 82801AA */ { 0x8086, 0x2426, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DEVICE_INTEL }, /* 82901AB */ { 0x8086, 0x2446, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DEVICE_INTEL }, /* 82801BA */ diff --git a/sound/pci/korg1212/korg1212.c b/sound/pci/korg1212/korg1212.c index 4721c096335..e39fad1a420 100644 --- a/sound/pci/korg1212/korg1212.c +++ b/sound/pci/korg1212/korg1212.c @@ -424,7 +424,7 @@ module_param_array(enable, bool, NULL, 0444); MODULE_PARM_DESC(enable, "Enable Korg 1212 soundcard."); MODULE_AUTHOR("Haroldo Gamal <gamal@alternex.com.br>"); -static struct pci_device_id snd_korg1212_ids[] = { +static struct pci_device_id snd_korg1212_ids[] __devinitdata = { { .vendor = 0x10b5, .device = 0x906d, diff --git a/sound/pci/maestro3.c b/sound/pci/maestro3.c index 9c90d901e6b..1928e06b6d8 100644 --- a/sound/pci/maestro3.c +++ b/sound/pci/maestro3.c @@ -41,7 +41,6 @@ #include <linux/slab.h> #include <linux/vmalloc.h> #include <linux/moduleparam.h> -#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/info.h> #include <sound/control.h> @@ -870,7 +869,7 @@ struct snd_m3 { /* * pci ids */ -static struct pci_device_id snd_m3_ids[] = { +static struct pci_device_id snd_m3_ids[] __devinitdata = { {PCI_VENDOR_ID_ESS, PCI_DEVICE_ID_ESS_ALLEGRO_1, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_MULTIMEDIA_AUDIO << 8, 0xffff00, 0}, {PCI_VENDOR_ID_ESS, PCI_DEVICE_ID_ESS_ALLEGRO, PCI_ANY_ID, PCI_ANY_ID, diff --git a/sound/pci/mixart/mixart.c b/sound/pci/mixart/mixart.c index b5a095052d4..09cc0786495 100644 --- a/sound/pci/mixart/mixart.c +++ b/sound/pci/mixart/mixart.c @@ -28,7 +28,6 @@ #include <linux/dma-mapping.h> #include <linux/moduleparam.h> #include <linux/mutex.h> -#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/initval.h> @@ -62,7 +61,7 @@ MODULE_PARM_DESC(enable, "Enable Digigram " CARD_NAME " soundcard."); /* */ -static struct pci_device_id snd_mixart_ids[] = { +static struct pci_device_id snd_mixart_ids[] __devinitdata = { { 0x1057, 0x0003, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, /* MC8240 */ { 0, } }; diff --git a/sound/pci/nm256/nm256.c b/sound/pci/nm256/nm256.c index cc297abc9d1..b92d6600deb 100644 --- a/sound/pci/nm256/nm256.c +++ b/sound/pci/nm256/nm256.c @@ -263,7 +263,7 @@ struct nm256 { /* * PCI ids */ -static struct pci_device_id snd_nm256_ids[] = { +static struct pci_device_id snd_nm256_ids[] __devinitdata = { {PCI_VENDOR_ID_NEOMAGIC, PCI_DEVICE_ID_NEOMAGIC_NM256AV_AUDIO, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, {PCI_VENDOR_ID_NEOMAGIC, PCI_DEVICE_ID_NEOMAGIC_NM256ZX_AUDIO, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, {PCI_VENDOR_ID_NEOMAGIC, PCI_DEVICE_ID_NEOMAGIC_NM256XL_PLUS_AUDIO, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, diff --git a/sound/pci/pcxhr/pcxhr.c b/sound/pci/pcxhr/pcxhr.c index 35875c8aa29..dafa2235aba 100644 --- a/sound/pci/pcxhr/pcxhr.c +++ b/sound/pci/pcxhr/pcxhr.c @@ -30,7 +30,6 @@ #include <linux/delay.h> #include <linux/moduleparam.h> #include <linux/mutex.h> -#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/initval.h> @@ -74,7 +73,7 @@ enum { PCI_ID_LAST }; -static struct pci_device_id pcxhr_ids[] = { +static struct pci_device_id pcxhr_ids[] __devinitdata = { { 0x10b5, 0x9656, 0x1369, 0xb001, 0, 0, PCI_ID_VX882HR, }, /* VX882HR */ { 0x10b5, 0x9656, 0x1369, 0xb101, 0, 0, PCI_ID_PCX882HR, }, /* PCX882HR */ { 0x10b5, 0x9656, 0x1369, 0xb201, 0, 0, PCI_ID_VX881HR, }, /* VX881HR */ diff --git a/sound/pci/pcxhr/pcxhr_hwdep.c b/sound/pci/pcxhr/pcxhr_hwdep.c index 03517c10e99..369c19fea98 100644 --- a/sound/pci/pcxhr/pcxhr_hwdep.c +++ b/sound/pci/pcxhr/pcxhr_hwdep.c @@ -385,8 +385,8 @@ static int pcxhr_hwdep_dsp_load(struct snd_hwdep *hw, fw.size = dsp->length; fw.data = vmalloc(fw.size); if (! fw.data) { - snd_printk(KERN_ERR "pcxhr: cannot allocate dsp image (%d bytes)\n", - fw.size); + snd_printk(KERN_ERR "pcxhr: cannot allocate dsp image (%lu bytes)\n", + (unsigned long)fw.size); return -ENOMEM; } if (copy_from_user(fw.data, dsp->image, dsp->length)) { diff --git a/sound/pci/riptide/riptide.c b/sound/pci/riptide/riptide.c index f148ee434a6..d8cc985d724 100644 --- a/sound/pci/riptide/riptide.c +++ b/sound/pci/riptide/riptide.c @@ -506,7 +506,7 @@ static int riptide_reset(struct cmdif *cif, struct snd_riptide *chip); /* */ -static struct pci_device_id snd_riptide_ids[] = { +static struct pci_device_id snd_riptide_ids[] __devinitdata = { { .vendor = 0x127a,.device = 0x4310, .subvendor = PCI_ANY_ID,.subdevice = PCI_ANY_ID, @@ -527,7 +527,7 @@ static struct pci_device_id snd_riptide_ids[] = { }; #ifdef SUPPORT_JOYSTICK -static struct pci_device_id snd_riptide_joystick_ids[] = { +static struct pci_device_id snd_riptide_joystick_ids[] __devinitdata = { { .vendor = 0x127a,.device = 0x4312, .subvendor = PCI_ANY_ID,.subdevice = PCI_ANY_ID, diff --git a/sound/pci/rme32.c b/sound/pci/rme32.c index ab78544bf04..55b1d4838d9 100644 --- a/sound/pci/rme32.c +++ b/sound/pci/rme32.c @@ -227,7 +227,7 @@ struct rme32 { struct snd_kcontrol *spdif_ctl; }; -static struct pci_device_id snd_rme32_ids[] = { +static struct pci_device_id snd_rme32_ids[] __devinitdata = { {PCI_VENDOR_ID_XILINX_RME, PCI_DEVICE_ID_RME_DIGI32, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0,}, {PCI_VENDOR_ID_XILINX_RME, PCI_DEVICE_ID_RME_DIGI32_8, diff --git a/sound/pci/rme96.c b/sound/pci/rme96.c index 6c2a9f4a765..3c1bc533d51 100644 --- a/sound/pci/rme96.c +++ b/sound/pci/rme96.c @@ -232,7 +232,7 @@ struct rme96 { struct snd_kcontrol *spdif_ctl; }; -static struct pci_device_id snd_rme96_ids[] = { +static struct pci_device_id snd_rme96_ids[] __devinitdata = { { PCI_VENDOR_ID_XILINX, PCI_DEVICE_ID_RME_DIGI96, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, { PCI_VENDOR_ID_XILINX, PCI_DEVICE_ID_RME_DIGI96_8, diff --git a/sound/pci/rme9652/hdsp.c b/sound/pci/rme9652/hdsp.c index ebf7a2b86c2..61f82f0d5cc 100644 --- a/sound/pci/rme9652/hdsp.c +++ b/sound/pci/rme9652/hdsp.c @@ -568,7 +568,7 @@ static void snd_hammerfall_free_buffer(struct snd_dma_buffer *dmab, struct pci_d } -static struct pci_device_id snd_hdsp_ids[] = { +static struct pci_device_id snd_hdsp_ids[] __devinitdata = { { .vendor = PCI_VENDOR_ID_XILINX, .device = PCI_DEVICE_ID_XILINX_HAMMERFALL_DSP, diff --git a/sound/pci/rme9652/hdspm.c b/sound/pci/rme9652/hdspm.c index b5538efd146..722b9e6ce54 100644 --- a/sound/pci/rme9652/hdspm.c +++ b/sound/pci/rme9652/hdspm.c @@ -426,7 +426,7 @@ static char channel_map_madi_qs[HDSPM_MAX_CHANNELS] = { }; -static struct pci_device_id snd_hdspm_ids[] = { +static struct pci_device_id snd_hdspm_ids[] __devinitdata = { { .vendor = PCI_VENDOR_ID_XILINX, .device = PCI_DEVICE_ID_XILINX_HAMMERFALL_DSP_MADI, diff --git a/sound/pci/rme9652/rme9652.c b/sound/pci/rme9652/rme9652.c index a687eb63236..75d6406303d 100644 --- a/sound/pci/rme9652/rme9652.c +++ b/sound/pci/rme9652/rme9652.c @@ -315,7 +315,7 @@ static void snd_hammerfall_free_buffer(struct snd_dma_buffer *dmab, struct pci_d } -static struct pci_device_id snd_rme9652_ids[] = { +static struct pci_device_id snd_rme9652_ids[] __devinitdata = { { .vendor = 0x10ee, .device = 0x3fc4, diff --git a/sound/pci/sonicvibes.c b/sound/pci/sonicvibes.c index 2d66a09fe5e..91f8bf3ae9f 100644 --- a/sound/pci/sonicvibes.c +++ b/sound/pci/sonicvibes.c @@ -243,7 +243,7 @@ struct sonicvibes { #endif }; -static struct pci_device_id snd_sonic_ids[] = { +static struct pci_device_id snd_sonic_ids[] __devinitdata = { { 0x5333, 0xca00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, { 0, } }; diff --git a/sound/pci/trident/trident.c b/sound/pci/trident/trident.c index b4538045049..9624a5f2b87 100644 --- a/sound/pci/trident/trident.c +++ b/sound/pci/trident/trident.c @@ -63,7 +63,7 @@ MODULE_PARM_DESC(pcm_channels, "Number of hardware channels assigned for PCM."); module_param_array(wavetable_size, int, NULL, 0444); MODULE_PARM_DESC(wavetable_size, "Maximum memory size in kB for wavetable synth."); -static struct pci_device_id snd_trident_ids[] = { +static struct pci_device_id snd_trident_ids[] __devinitdata = { {PCI_DEVICE(PCI_VENDOR_ID_TRIDENT, PCI_DEVICE_ID_TRIDENT_4DWAVE_DX), PCI_CLASS_MULTIMEDIA_AUDIO << 8, 0xffff00, 0}, {PCI_DEVICE(PCI_VENDOR_ID_TRIDENT, PCI_DEVICE_ID_TRIDENT_4DWAVE_NX), diff --git a/sound/pci/via82xx.c b/sound/pci/via82xx.c index 0f171dd1377..39daf62d2ba 100644 --- a/sound/pci/via82xx.c +++ b/sound/pci/via82xx.c @@ -123,6 +123,7 @@ module_param(enable, bool, 0444); #define VIA_REV_8233A 0x40 /* 1 rec, 1 multi-pb, spdf */ #define VIA_REV_8235 0x50 /* 2 rec, 4 pb, 1 multi-pb, spdif */ #define VIA_REV_8237 0x60 +#define VIA_REV_8251 0x70 /* * Direct registers @@ -395,7 +396,7 @@ struct via82xx { #endif }; -static struct pci_device_id snd_via82xx_ids[] = { +static struct pci_device_id snd_via82xx_ids[] __devinitdata = { /* 0x1106, 0x3058 */ { PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_5, PCI_ANY_ID, PCI_ANY_ID, 0, 0, TYPE_CARD_VIA686, }, /* 686A */ /* 0x1106, 0x3059 */ @@ -862,6 +863,11 @@ static snd_pcm_uframes_t snd_via8233_pcm_pointer(struct snd_pcm_substream *subst if (!status) status = inb(VIADEV_REG(viadev, OFFSET_STATUS)); + /* An apparent bug in the 8251 is worked around by sending a + * REG_CTRL_START. */ + if (chip->revision == VIA_REV_8251 && (status & VIA_REG_STAT_EOL)) + snd_via82xx_pcm_trigger(substream, SNDRV_PCM_TRIGGER_START); + if (!(status & VIA_REG_STAT_ACTIVE)) { res = 0; goto unlock; @@ -2313,6 +2319,7 @@ static struct via823x_info via823x_cards[] __devinitdata = { { VIA_REV_8233A, "VIA 8233A", TYPE_VIA8233A }, { VIA_REV_8235, "VIA 8235", TYPE_VIA8233 }, { VIA_REV_8237, "VIA 8237", TYPE_VIA8233 }, + { VIA_REV_8251, "VIA 8251", TYPE_VIA8233 }, }; /* @@ -2325,7 +2332,7 @@ struct dxs_whitelist { short action; /* new dxs_support value */ }; -static int __devinit check_dxs_list(struct pci_dev *pci) +static int __devinit check_dxs_list(struct pci_dev *pci, int revision) { static struct dxs_whitelist whitelist[] = { { .subvendor = 0x1005, .subdevice = 0x4710, .action = VIA_DXS_ENABLE }, /* Avance Logic Mobo */ @@ -2342,6 +2349,7 @@ static int __devinit check_dxs_list(struct pci_dev *pci) { .subvendor = 0x1043, .subdevice = 0x810d, .action = VIA_DXS_SRC }, /* ASUS */ { .subvendor = 0x1043, .subdevice = 0x812a, .action = VIA_DXS_SRC }, /* ASUS A8V Deluxe */ { .subvendor = 0x1043, .subdevice = 0x8174, .action = VIA_DXS_SRC }, /* ASUS */ + { .subvendor = 0x1043, .subdevice = 0x81b9, .action = VIA_DXS_SRC }, /* ASUS A8V-MX */ { .subvendor = 0x1071, .subdevice = 0x8375, .action = VIA_DXS_NO_VRA }, /* Vobis/Yakumo/Mitac notebook */ { .subvendor = 0x1071, .subdevice = 0x8399, .action = VIA_DXS_NO_VRA }, /* Umax AB 595T (VIA K8N800A - VT8237) */ { .subvendor = 0x10cf, .subdevice = 0x118e, .action = VIA_DXS_ENABLE }, /* FSC laptop */ @@ -2405,6 +2413,10 @@ static int __devinit check_dxs_list(struct pci_dev *pci) } } + /* for newer revision, default to DXS_SRC */ + if (revision >= VIA_REV_8235) + return VIA_DXS_SRC; + /* * not detected, try 48k rate only to be sure. */ @@ -2449,7 +2461,7 @@ static int __devinit snd_via82xx_probe(struct pci_dev *pci, } if (chip_type != TYPE_VIA8233A) { if (dxs_support == VIA_DXS_AUTO) - dxs_support = check_dxs_list(pci); + dxs_support = check_dxs_list(pci, revision); /* force to use VIA8233 or 8233A model according to * dxs_support module option */ diff --git a/sound/pci/via82xx_modem.c b/sound/pci/via82xx_modem.c index 22ce4d30992..ef97e50cd6c 100644 --- a/sound/pci/via82xx_modem.c +++ b/sound/pci/via82xx_modem.c @@ -261,7 +261,7 @@ struct via82xx_modem { struct snd_info_entry *proc_entry; }; -static struct pci_device_id snd_via82xx_modem_ids[] = { +static struct pci_device_id snd_via82xx_modem_ids[] __devinitdata = { { 0x1106, 0x3068, PCI_ANY_ID, PCI_ANY_ID, 0, 0, TYPE_CARD_VIA82XX_MODEM, }, { 0, } }; diff --git a/sound/pci/vx222/vx222.c b/sound/pci/vx222/vx222.c index c816ddf1b21..0f1ebb010a5 100644 --- a/sound/pci/vx222/vx222.c +++ b/sound/pci/vx222/vx222.c @@ -60,7 +60,7 @@ enum { VX_PCI_VX222_NEW }; -static struct pci_device_id snd_vx222_ids[] = { +static struct pci_device_id snd_vx222_ids[] __devinitdata = { { 0x10b5, 0x9050, 0x1369, PCI_ANY_ID, 0, 0, VX_PCI_VX222_OLD, }, /* PLX */ { 0x10b5, 0x9030, 0x1369, PCI_ANY_ID, 0, 0, VX_PCI_VX222_NEW, }, /* PLX */ { 0, } diff --git a/sound/pci/ymfpci/ymfpci.c b/sound/pci/ymfpci/ymfpci.c index db57ce939fa..65ebf5f1933 100644 --- a/sound/pci/ymfpci/ymfpci.c +++ b/sound/pci/ymfpci/ymfpci.c @@ -70,7 +70,7 @@ MODULE_PARM_DESC(rear_switch, "Enable shared rear/line-in switch"); module_param_array(rear_swap, bool, NULL, 0444); MODULE_PARM_DESC(rear_swap, "Swap rear channels (must be enabled for correct IEC958 (S/PDIF)) output"); -static struct pci_device_id snd_ymfpci_ids[] = { +static struct pci_device_id snd_ymfpci_ids[] __devinitdata = { { 0x1073, 0x0004, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, /* YMF724 */ { 0x1073, 0x000d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, /* YMF724F */ { 0x1073, 0x000a, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, /* YMF740 */ diff --git a/sound/pcmcia/Kconfig b/sound/pcmcia/Kconfig index 5d1b0b762ef..c9fa1a2bc58 100644 --- a/sound/pcmcia/Kconfig +++ b/sound/pcmcia/Kconfig @@ -5,7 +5,7 @@ menu "PCMCIA devices" config SND_VXPOCKET tristate "Digigram VXpocket" - depends on SND && PCMCIA && ISA + depends on SND && PCMCIA select SND_VX_LIB help Say Y here to include support for Digigram VXpocket and @@ -16,7 +16,7 @@ config SND_VXPOCKET config SND_PDAUDIOCF tristate "Sound Core PDAudioCF" - depends on SND && PCMCIA && ISA + depends on SND && PCMCIA select SND_PCM help Say Y here to include support for Sound Core PDAudioCF diff --git a/sound/ppc/toonie.c b/sound/ppc/toonie.c index 4e595172e42..1ac7c8552f5 100644 --- a/sound/ppc/toonie.c +++ b/sound/ppc/toonie.c @@ -335,7 +335,7 @@ static void toonie_cleanup(struct snd_pmac *chip) chip->mixer_data = NULL; } -int snd_pmac_toonie_init(struct snd_pmac *chip) +int __init snd_pmac_toonie_init(struct snd_pmac *chip) { struct pmac_toonie *mix; diff --git a/sound/usb/usbquirks.h b/sound/usb/usbquirks.h index 0992a0923f1..9351846d7a9 100644 --- a/sound/usb/usbquirks.h +++ b/sound/usb/usbquirks.h @@ -1531,6 +1531,15 @@ YAMAHA_DEVICE(0x7010, "UB99"), } }, { + USB_DEVICE_VENDOR_SPEC(0x0ccd, 0x0014), + .driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) { + .vendor_name = "TerraTec", + .product_name = "PHASE 26", + .ifnum = 3, + .type = QUIRK_MIDI_STANDARD_INTERFACE + } +}, +{ USB_DEVICE(0x0ccd, 0x0035), .driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) { .vendor_name = "Miditech", |