diff options
| -rw-r--r-- | drivers/ssb/driver_chipcommon.c | 36 | ||||
| -rw-r--r-- | include/linux/ssb/ssb_driver_chipcommon.h | 3 |
2 files changed, 34 insertions, 5 deletions
diff --git a/drivers/ssb/driver_chipcommon.c b/drivers/ssb/driver_chipcommon.c index 6fbf1c53b6f..7cc03f2dd5a 100644 --- a/drivers/ssb/driver_chipcommon.c +++ b/drivers/ssb/driver_chipcommon.c @@ -376,6 +376,7 @@ int ssb_chipco_serial_init(struct ssb_chipcommon *cc, unsigned int irq; u32 baud_base, div; u32 i, n; + unsigned int ccrev = cc->dev->id.revision; plltype = (cc->capabilities & SSB_CHIPCO_CAP_PLLT); irq = ssb_mips_irq(cc->dev); @@ -387,14 +388,39 @@ int ssb_chipco_serial_init(struct ssb_chipcommon *cc, chipco_read32(cc, SSB_CHIPCO_CLOCK_M2)); div = 1; } else { - if (cc->dev->id.revision >= 11) { + if (ccrev == 20) { + /* BCM5354 uses constant 25MHz clock */ + baud_base = 25000000; + div = 48; + /* Set the override bit so we don't divide it */ + chipco_write32(cc, SSB_CHIPCO_CORECTL, + chipco_read32(cc, SSB_CHIPCO_CORECTL) + | SSB_CHIPCO_CORECTL_UARTCLK0); + } else if ((ccrev >= 11) && (ccrev != 15)) { /* Fixed ALP clock */ baud_base = 20000000; + if (cc->capabilities & SSB_CHIPCO_CAP_PMU) { + /* FIXME: baud_base is different for devices with a PMU */ + SSB_WARN_ON(1); + } div = 1; + if (ccrev >= 21) { + /* Turn off UART clock before switching clocksource. */ + chipco_write32(cc, SSB_CHIPCO_CORECTL, + chipco_read32(cc, SSB_CHIPCO_CORECTL) + & ~SSB_CHIPCO_CORECTL_UARTCLKEN); + } /* Set the override bit so we don't divide it */ chipco_write32(cc, SSB_CHIPCO_CORECTL, - SSB_CHIPCO_CORECTL_UARTCLK0); - } else if (cc->dev->id.revision >= 3) { + chipco_read32(cc, SSB_CHIPCO_CORECTL) + | SSB_CHIPCO_CORECTL_UARTCLK0); + if (ccrev >= 21) { + /* Re-enable the UART clock. */ + chipco_write32(cc, SSB_CHIPCO_CORECTL, + chipco_read32(cc, SSB_CHIPCO_CORECTL) + | SSB_CHIPCO_CORECTL_UARTCLKEN); + } + } else if (ccrev >= 3) { /* Internal backplane clock */ baud_base = ssb_clockspeed(bus); div = chipco_read32(cc, SSB_CHIPCO_CLKDIV) @@ -406,7 +432,7 @@ int ssb_chipco_serial_init(struct ssb_chipcommon *cc, } /* Clock source depends on strapping if UartClkOverride is unset */ - if ((cc->dev->id.revision > 0) && + if ((ccrev > 0) && !(chipco_read32(cc, SSB_CHIPCO_CORECTL) & SSB_CHIPCO_CORECTL_UARTCLK0)) { if ((cc->capabilities & SSB_CHIPCO_CAP_UARTCLK) == SSB_CHIPCO_CAP_UARTCLK_INT) { @@ -428,7 +454,7 @@ int ssb_chipco_serial_init(struct ssb_chipcommon *cc, cc_mmio = cc->dev->bus->mmio + (cc->dev->core_index * SSB_CORE_SIZE); uart_regs = cc_mmio + SSB_CHIPCO_UART0_DATA; /* Offset changed at after rev 0 */ - if (cc->dev->id.revision == 0) + if (ccrev == 0) uart_regs += (i * 8); else uart_regs += (i * 256); diff --git a/include/linux/ssb/ssb_driver_chipcommon.h b/include/linux/ssb/ssb_driver_chipcommon.h index 4cb99549466..35717b400ce 100644 --- a/include/linux/ssb/ssb_driver_chipcommon.h +++ b/include/linux/ssb/ssb_driver_chipcommon.h @@ -51,9 +51,12 @@ #define SSB_CHIPCO_CAP_JTAGM 0x00400000 /* JTAG master present */ #define SSB_CHIPCO_CAP_BROM 0x00800000 /* Internal boot ROM active */ #define SSB_CHIPCO_CAP_64BIT 0x08000000 /* 64-bit Backplane */ +#define SSB_CHIPCO_CAP_PMU 0x10000000 /* PMU available (rev >= 20) */ +#define SSB_CHIPCO_CAP_ECI 0x20000000 /* ECI available (rev >= 20) */ #define SSB_CHIPCO_CORECTL 0x0008 #define SSB_CHIPCO_CORECTL_UARTCLK0 0x00000001 /* Drive UART with internal clock */ #define SSB_CHIPCO_CORECTL_SE 0x00000002 /* sync clk out enable (corerev >= 3) */ +#define SSB_CHIPCO_CORECTL_UARTCLKEN 0x00000008 /* UART clock enable (rev >= 21) */ #define SSB_CHIPCO_BIST 0x000C #define SSB_CHIPCO_OTPS 0x0010 /* OTP status */ #define SSB_CHIPCO_OTPS_PROGFAIL 0x80000000 |