diff options
| -rw-r--r-- | drivers/input/touchscreen/ads7846.c | 80 |
1 files changed, 41 insertions, 39 deletions
diff --git a/drivers/input/touchscreen/ads7846.c b/drivers/input/touchscreen/ads7846.c index 11979be3358..b18c63a3f2a 100644 --- a/drivers/input/touchscreen/ads7846.c +++ b/drivers/input/touchscreen/ads7846.c @@ -378,11 +378,8 @@ static struct attribute_group ads7845_attr_group = { static void ads7846_rx(void *ads) { struct ads7846 *ts = ads; - struct input_dev *input_dev = ts->input; unsigned Rt; - unsigned sync = 0; u16 x, y, z1, z2; - unsigned long flags; /* ads7846_rx_val() did in-place conversion (including byteswap) from * on-the-wire format as part of debouncing to get stable readings. @@ -396,7 +393,7 @@ static void ads7846_rx(void *ads) if (x == MAX_12BIT) x = 0; - if (likely(x && z1 && !device_suspended(&ts->spi->dev))) { + if (likely(x && z1)) { /* compute touch pressure resistance using equation #2 */ Rt = z2; Rt -= z1; @@ -412,52 +409,44 @@ static void ads7846_rx(void *ads) * once more the measurement */ if (ts->tc.ignore || Rt > ts->pressure_max) { +#ifdef VERBOSE + pr_debug("%s: ignored %d pressure %d\n", + ts->spi->dev.bus_id, ts->tc.ignore, Rt); +#endif hrtimer_start(&ts->timer, ktime_set(0, TS_POLL_PERIOD), HRTIMER_REL); return; } - /* NOTE: "pendown" is inferred from pressure; we don't rely on - * being able to check nPENIRQ status, or "friendly" trigger modes - * (both-edges is much better than just-falling or low-level). - * - * REVISIT: some boards may require reading nPENIRQ; it's - * needed on 7843. and 7845 reads pressure differently... + /* NOTE: We can't rely on the pressure to determine the pen down + * state, even this controller has a pressure sensor. The pressure + * value can fluctuate for quite a while after lifting the pen and + * in some cases may not even settle at the expected value. * - * REVISIT: the touchscreen might not be connected; this code - * won't notice that, even if nPENIRQ never fires ... + * The only safe way to check for the pen up condition is in the + * timer by reading the pen signal state (it's a GPIO _and_ IRQ). */ - if (!ts->pendown && Rt != 0) { - input_report_key(input_dev, BTN_TOUCH, 1); - sync = 1; - } else if (ts->pendown && Rt == 0) { - input_report_key(input_dev, BTN_TOUCH, 0); - sync = 1; - } - if (Rt) { - input_report_abs(input_dev, ABS_X, x); - input_report_abs(input_dev, ABS_Y, y); - sync = 1; - } + struct input_dev *input = ts->input; - if (sync) { - input_report_abs(input_dev, ABS_PRESSURE, Rt); - input_sync(input_dev); - } - -#ifdef VERBOSE - if (Rt || ts->pendown) - pr_debug("%s: %d/%d/%d%s\n", ts->spi->dev.bus_id, - x, y, Rt, Rt ? "" : " UP"); + if (!ts->pendown) { + input_report_key(input, BTN_TOUCH, 1); + ts->pendown = 1; +#ifdef VERBOSE + dev_dbg(&ts->spi->dev, "DOWN\n"); #endif + } + input_report_abs(input, ABS_X, x); + input_report_abs(input, ABS_Y, y); + input_report_abs(input, ABS_PRESSURE, Rt); - spin_lock_irqsave(&ts->lock, flags); + input_sync(input); +#ifdef VERBOSE + dev_dbg(&ts->spi->dev, "%4d/%4d/%4d\n", x, y, Rt); +#endif + } - ts->pendown = (Rt != 0); hrtimer_start(&ts->timer, ktime_set(0, TS_POLL_PERIOD), HRTIMER_REL); - - spin_unlock_irqrestore(&ts->lock, flags); } static int ads7846_debounce(void *ads, int data_idx, int *val) @@ -553,14 +542,27 @@ static int ads7846_timer(struct hrtimer *handle) spin_lock_irq(&ts->lock); - if (unlikely(ts->msg_idx && !ts->pendown)) { + if (unlikely(!ts->get_pendown_state() || + device_suspended(&ts->spi->dev))) { + if (ts->pendown) { + struct input_dev *input = ts->input; + + input_report_key(input, BTN_TOUCH, 0); + input_report_abs(input, ABS_PRESSURE, 0); + input_sync(input); + + ts->pendown = 0; +#ifdef VERBOSE + dev_dbg(&ts->spi->dev, "UP\n"); +#endif + } + /* measurement cycle ended */ if (!device_suspended(&ts->spi->dev)) { ts->irq_disabled = 0; enable_irq(ts->spi->irq); } ts->pending = 0; - ts->msg_idx = 0; } else { /* pen is still down, continue with the measurement */ ts->msg_idx = 0; |