diff options
| -rw-r--r-- | drivers/video/Kconfig | 17 | ||||
| -rw-r--r-- | drivers/video/hecubafb.c | 250 | ||||
| -rw-r--r-- | drivers/video/n411.c | 202 | ||||
| -rw-r--r-- | include/video/hecubafb.h | 51 |
4 files changed, 314 insertions, 206 deletions
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig index ff6ea9a9be2..73d3afad7c5 100644 --- a/drivers/video/Kconfig +++ b/drivers/video/Kconfig @@ -178,6 +178,11 @@ config FB_METRONOME depends on FB depends on FB_DEFERRED_IO +config FB_HECUBA + tristate + depends on FB + depends on FB_DEFERRED_IO + config FB_SVGALIB tristate depends on FB @@ -703,20 +708,18 @@ config FB_IMAC help This is the frame buffer device driver for the Intel-based Macintosh -config FB_HECUBA - tristate "Hecuba board support" +config FB_N411 + tristate "N411 Apollo/Hecuba devkit support" depends on FB && X86 && MMU select FB_SYS_FILLRECT select FB_SYS_COPYAREA select FB_SYS_IMAGEBLIT select FB_SYS_FOPS select FB_DEFERRED_IO + select FB_HECUBA help - This enables support for the Hecuba board. This driver was tested - with an E-Ink 800x600 display and x86 SBCs through a 16 bit GPIO - interface (8 bit data, 4 bit control). If you anticipate using - this driver, say Y or M; otherwise say N. You must specify the - GPIO IO address to be used for setting control and data. + This enables support for the Apollo display controller in its + Hecuba form using the n411 devkit. config FB_HGA tristate "Hercules mono graphics support" diff --git a/drivers/video/hecubafb.c b/drivers/video/hecubafb.c index b77d033665d..0b4bffbe67c 100644 --- a/drivers/video/hecubafb.c +++ b/drivers/video/hecubafb.c @@ -1,5 +1,5 @@ /* - * linux/drivers/video/hecubafb.c -- FB driver for Hecuba controller + * linux/drivers/video/hecubafb.c -- FB driver for Hecuba/Apollo controller * * Copyright (C) 2006, Jaya Kumar * This work was sponsored by CIS(M) Sdn Bhd @@ -17,18 +17,13 @@ * values. There are other commands that the display is capable of, * beyond the 5 used here but they are more complex. * - * This driver is written to be used with the Hecuba display controller - * board, and tested with the EInk 800x600 display in 1 bit mode. - * The interface between Hecuba and the host is TTL based GPIO. The - * GPIO requirements are 8 writable data lines and 6 lines for control. - * Only 4 of the controls are actually used here but 6 for future use. - * The driver requires the IO addresses for data and control GPIO at - * load time. It is also possible to use this display with a standard - * PC parallel port. + * This driver is written to be used with the Hecuba display architecture. + * The actual display chip is called Apollo and the interface electronics + * it needs is called Hecuba. * - * General notes: - * - User must set hecubafb_enable=1 to enable it - * - User must set dio_addr=0xIOADDR cio_addr=0xIOADDR c2io_addr=0xIOADDR + * It is intended to be architecture independent. A board specific driver + * must be used to perform all the physical IO interactions. An example + * is provided as n411.c * */ @@ -47,34 +42,12 @@ #include <linux/list.h> #include <linux/uaccess.h> -/* Apollo controller specific defines */ -#define APOLLO_START_NEW_IMG 0xA0 -#define APOLLO_STOP_IMG_DATA 0xA1 -#define APOLLO_DISPLAY_IMG 0xA2 -#define APOLLO_ERASE_DISPLAY 0xA3 -#define APOLLO_INIT_DISPLAY 0xA4 - -/* Hecuba interface specific defines */ -/* WUP is inverted, CD is inverted, DS is inverted */ -#define HCB_NWUP_BIT 0x01 -#define HCB_NDS_BIT 0x02 -#define HCB_RW_BIT 0x04 -#define HCB_NCD_BIT 0x08 -#define HCB_ACK_BIT 0x80 +#include <video/hecubafb.h> /* Display specific information */ #define DPY_W 600 #define DPY_H 800 -struct hecubafb_par { - unsigned long dio_addr; - unsigned long cio_addr; - unsigned long c2io_addr; - unsigned char ctl; - struct fb_info *info; - unsigned int irq; -}; - static struct fb_fix_screeninfo hecubafb_fix __devinitdata = { .id = "hecubafb", .type = FB_TYPE_PACKED_PIXELS, @@ -82,6 +55,7 @@ static struct fb_fix_screeninfo hecubafb_fix __devinitdata = { .xpanstep = 0, .ypanstep = 0, .ywrapstep = 0, + .line_length = DPY_W, .accel = FB_ACCEL_NONE, }; @@ -94,136 +68,51 @@ static struct fb_var_screeninfo hecubafb_var __devinitdata = { .nonstd = 1, }; -static unsigned long dio_addr; -static unsigned long cio_addr; -static unsigned long c2io_addr; -static unsigned long splashval; -static unsigned int nosplash; -static unsigned int hecubafb_enable; -static unsigned int irq; - -static DECLARE_WAIT_QUEUE_HEAD(hecubafb_waitq); - -static void hcb_set_ctl(struct hecubafb_par *par) -{ - outb(par->ctl, par->cio_addr); -} - -static unsigned char hcb_get_ctl(struct hecubafb_par *par) -{ - return inb(par->c2io_addr); -} - -static void hcb_set_data(struct hecubafb_par *par, unsigned char value) -{ - outb(value, par->dio_addr); -} - -static int __devinit apollo_init_control(struct hecubafb_par *par) -{ - unsigned char ctl; - /* for init, we want the following setup to be set: - WUP = lo - ACK = hi - DS = hi - RW = hi - CD = lo - */ - - /* write WUP to lo, DS to hi, RW to hi, CD to lo */ - par->ctl = HCB_NWUP_BIT | HCB_RW_BIT | HCB_NCD_BIT ; - par->ctl &= ~HCB_NDS_BIT; - hcb_set_ctl(par); - - /* check ACK is not lo */ - ctl = hcb_get_ctl(par); - if ((ctl & HCB_ACK_BIT)) { - printk(KERN_ERR "Fail because ACK is already low\n"); - return -ENXIO; - } - - return 0; -} - -static void hcb_wait_for_ack(struct hecubafb_par *par) -{ - - int timeout; - unsigned char ctl; - - timeout=500; - do { - ctl = hcb_get_ctl(par); - if ((ctl & HCB_ACK_BIT)) - return; - udelay(1); - } while (timeout--); - printk(KERN_ERR "timed out waiting for ack\n"); -} - -static void hcb_wait_for_ack_clear(struct hecubafb_par *par) -{ - - int timeout; - unsigned char ctl; - - timeout=500; - do { - ctl = hcb_get_ctl(par); - if (!(ctl & HCB_ACK_BIT)) - return; - udelay(1); - } while (timeout--); - printk(KERN_ERR "timed out waiting for clear\n"); -} +/* main hecubafb functions */ static void apollo_send_data(struct hecubafb_par *par, unsigned char data) { /* set data */ - hcb_set_data(par, data); + par->board->set_data(par, data); /* set DS low */ - par->ctl |= HCB_NDS_BIT; - hcb_set_ctl(par); + par->board->set_ctl(par, HCB_DS_BIT, 0); - hcb_wait_for_ack(par); + /* wait for ack */ + par->board->wait_for_ack(par, 0); /* set DS hi */ - par->ctl &= ~(HCB_NDS_BIT); - hcb_set_ctl(par); + par->board->set_ctl(par, HCB_DS_BIT, 1); - hcb_wait_for_ack_clear(par); + /* wait for ack to clear */ + par->board->wait_for_ack(par, 1); } static void apollo_send_command(struct hecubafb_par *par, unsigned char data) { /* command so set CD to high */ - par->ctl &= ~(HCB_NCD_BIT); - hcb_set_ctl(par); + par->board->set_ctl(par, HCB_CD_BIT, 1); /* actually strobe with command */ apollo_send_data(par, data); /* clear CD back to low */ - par->ctl |= (HCB_NCD_BIT); - hcb_set_ctl(par); + par->board->set_ctl(par, HCB_CD_BIT, 0); } -/* main hecubafb functions */ - static void hecubafb_dpy_update(struct hecubafb_par *par) { int i; unsigned char *buf = (unsigned char __force *)par->info->screen_base; - apollo_send_command(par, 0xA0); + apollo_send_command(par, APOLLO_START_NEW_IMG); for (i=0; i < (DPY_W*DPY_H/8); i++) { apollo_send_data(par, *(buf++)); } - apollo_send_command(par, 0xA1); - apollo_send_command(par, 0xA2); + apollo_send_command(par, APOLLO_STOP_IMG_DATA); + apollo_send_command(par, APOLLO_DISPLAY_IMG); } /* this is called back from the deferred io workqueue */ @@ -326,11 +215,21 @@ static struct fb_deferred_io hecubafb_defio = { static int __devinit hecubafb_probe(struct platform_device *dev) { struct fb_info *info; + struct hecuba_board *board; int retval = -ENOMEM; int videomemorysize; unsigned char *videomemory; struct hecubafb_par *par; + /* pick up board specific routines */ + board = dev->dev.platform_data; + if (!board) + return -EINVAL; + + /* try to count device specific driver, if can't, platform recalls */ + if (!try_module_get(board->owner)) + return -ENODEV; + videomemorysize = (DPY_W*DPY_H)/8; if (!(videomemory = vmalloc(videomemorysize))) @@ -340,9 +239,9 @@ static int __devinit hecubafb_probe(struct platform_device *dev) info = framebuffer_alloc(sizeof(struct hecubafb_par), &dev->dev); if (!info) - goto err; + goto err_fballoc; - info->screen_base = (char __iomem *) videomemory; + info->screen_base = (char __force __iomem *)videomemory; info->fbops = &hecubafb_ops; info->var = hecubafb_var; @@ -350,14 +249,10 @@ static int __devinit hecubafb_probe(struct platform_device *dev) info->fix.smem_len = videomemorysize; par = info->par; par->info = info; + par->board = board; + par->send_command = apollo_send_command; + par->send_data = apollo_send_data; - if (!dio_addr || !cio_addr || !c2io_addr) { - printk(KERN_WARNING "no IO addresses supplied\n"); - goto err1; - } - par->dio_addr = dio_addr; - par->cio_addr = cio_addr; - par->c2io_addr = c2io_addr; info->flags = FBINFO_FLAG_DEFAULT; info->fbdefio = &hecubafb_defio; @@ -365,7 +260,7 @@ static int __devinit hecubafb_probe(struct platform_device *dev) retval = register_framebuffer(info); if (retval < 0) - goto err1; + goto err_fbreg; platform_set_drvdata(dev, info); printk(KERN_INFO @@ -373,25 +268,16 @@ static int __devinit hecubafb_probe(struct platform_device *dev) info->node, videomemorysize >> 10); /* this inits the dpy */ - apollo_init_control(par); - - apollo_send_command(par, APOLLO_INIT_DISPLAY); - apollo_send_data(par, 0x81); - - /* have to wait while display resets */ - udelay(1000); - - /* if we were told to splash the screen, we just clear it */ - if (!nosplash) { - apollo_send_command(par, APOLLO_ERASE_DISPLAY); - apollo_send_data(par, splashval); - } + retval = par->board->init(par); + if (retval < 0) + goto err_fbreg; return 0; -err1: +err_fbreg: framebuffer_release(info); -err: +err_fballoc: vfree(videomemory); + module_put(board->owner); return retval; } @@ -400,9 +286,13 @@ static int __devexit hecubafb_remove(struct platform_device *dev) struct fb_info *info = platform_get_drvdata(dev); if (info) { + struct hecubafb_par *par = info->par; fb_deferred_io_cleanup(info); unregister_framebuffer(info); vfree((void __force *)info->screen_base); + if (par->board->remove) + par->board->remove(par); + module_put(par->board->owner); framebuffer_release(info); } return 0; @@ -412,62 +302,24 @@ static struct platform_driver hecubafb_driver = { .probe = hecubafb_probe, .remove = hecubafb_remove, .driver = { + .owner = THIS_MODULE, .name = "hecubafb", }, }; -static struct platform_device *hecubafb_device; - static int __init hecubafb_init(void) { - int ret; - - if (!hecubafb_enable) { - printk(KERN_ERR "Use hecubafb_enable to enable the device\n"); - return -ENXIO; - } - - ret = platform_driver_register(&hecubafb_driver); - if (!ret) { - hecubafb_device = platform_device_alloc("hecubafb", 0); - if (hecubafb_device) - ret = platform_device_add(hecubafb_device); - else - ret = -ENOMEM; - - if (ret) { - platform_device_put(hecubafb_device); - platform_driver_unregister(&hecubafb_driver); - } - } - return ret; - + return platform_driver_register(&hecubafb_driver); } static void __exit hecubafb_exit(void) { - platform_device_unregister(hecubafb_device); platform_driver_unregister(&hecubafb_driver); } -module_param(nosplash, uint, 0); -MODULE_PARM_DESC(nosplash, "Disable doing the splash screen"); -module_param(hecubafb_enable, uint, 0); -MODULE_PARM_DESC(hecubafb_enable, "Enable communication with Hecuba board"); -module_param(dio_addr, ulong, 0); -MODULE_PARM_DESC(dio_addr, "IO address for data, eg: 0x480"); -module_param(cio_addr, ulong, 0); -MODULE_PARM_DESC(cio_addr, "IO address for control, eg: 0x400"); -module_param(c2io_addr, ulong, 0); -MODULE_PARM_DESC(c2io_addr, "IO address for secondary control, eg: 0x408"); -module_param(splashval, ulong, 0); -MODULE_PARM_DESC(splashval, "Splash pattern: 0x00 is black, 0x01 is white"); -module_param(irq, uint, 0); -MODULE_PARM_DESC(irq, "IRQ for the Hecuba board"); - module_init(hecubafb_init); module_exit(hecubafb_exit); -MODULE_DESCRIPTION("fbdev driver for Hecuba board"); +MODULE_DESCRIPTION("fbdev driver for Hecuba/Apollo controller"); MODULE_AUTHOR("Jaya Kumar"); MODULE_LICENSE("GPL"); diff --git a/drivers/video/n411.c b/drivers/video/n411.c new file mode 100644 index 00000000000..935830fea7b --- /dev/null +++ b/drivers/video/n411.c @@ -0,0 +1,202 @@ +/* + * linux/drivers/video/n411.c -- Platform device for N411 EPD kit + * + * Copyright (C) 2008, Jaya Kumar + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive for + * more details. + * + * Layout is based on skeletonfb.c by James Simmons and Geert Uytterhoeven. + * + * This driver is written to be used with the Hecuba display controller + * board, and tested with the EInk 800x600 display in 1 bit mode. + * The interface between Hecuba and the host is TTL based GPIO. The + * GPIO requirements are 8 writable data lines and 6 lines for control. + * Only 4 of the controls are actually used here but 6 for future use. + * The driver requires the IO addresses for data and control GPIO at + * load time. It is also possible to use this display with a standard + * PC parallel port. + * + * General notes: + * - User must set dio_addr=0xIOADDR cio_addr=0xIOADDR c2io_addr=0xIOADDR + * + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/string.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/fb.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/list.h> +#include <linux/uaccess.h> +#include <linux/irq.h> + +#include <video/hecubafb.h> + +static unsigned long dio_addr; +static unsigned long cio_addr; +static unsigned long c2io_addr; +static unsigned long splashval; +static unsigned int nosplash; +static unsigned char ctl; + +static void n411_set_ctl(struct hecubafb_par *par, unsigned char bit, unsigned + char state) +{ + switch (bit) { + case HCB_CD_BIT: + if (state) + ctl &= ~(HCB_CD_BIT); + else + ctl |= HCB_CD_BIT; + break; + case HCB_DS_BIT: + if (state) + ctl &= ~(HCB_DS_BIT); + else + ctl |= HCB_DS_BIT; + break; + } + outb(ctl, cio_addr); +} + +static unsigned char n411_get_ctl(struct hecubafb_par *par) +{ + return inb(c2io_addr); +} + +static void n411_set_data(struct hecubafb_par *par, unsigned char value) +{ + outb(value, dio_addr); +} + +static void n411_wait_for_ack(struct hecubafb_par *par, int clear) +{ + int timeout; + unsigned char tmp; + + timeout = 500; + do { + tmp = n411_get_ctl(par); + if ((tmp & HCB_ACK_BIT) && (!clear)) + return; + else if (!(tmp & HCB_ACK_BIT) && (clear)) + return; + udelay(1); + } while (timeout--); + printk(KERN_ERR "timed out waiting for ack\n"); +} + +static int n411_init_control(struct hecubafb_par *par) +{ + unsigned char tmp; + /* for init, we want the following setup to be set: + WUP = lo + ACK = hi + DS = hi + RW = hi + CD = lo + */ + + /* write WUP to lo, DS to hi, RW to hi, CD to lo */ + ctl = HCB_WUP_BIT | HCB_RW_BIT | HCB_CD_BIT ; + n411_set_ctl(par, HCB_DS_BIT, 1); + + /* check ACK is not lo */ + tmp = n411_get_ctl(par); + if (tmp & HCB_ACK_BIT) { + printk(KERN_ERR "Fail because ACK is already low\n"); + return -ENXIO; + } + + return 0; +} + + +static int n411_init_board(struct hecubafb_par *par) +{ + int retval; + + retval = n411_init_control(par); + if (retval) + return retval; + + par->send_command(par, APOLLO_INIT_DISPLAY); + par->send_data(par, 0x81); + + /* have to wait while display resets */ + udelay(1000); + + /* if we were told to splash the screen, we just clear it */ + if (!nosplash) { + par->send_command(par, APOLLO_ERASE_DISPLAY); + par->send_data(par, splashval); + } + + return 0; +} + +static struct hecuba_board n411_board = { + .owner = THIS_MODULE, + .init = n411_init_board, + .set_ctl = n411_set_ctl, + .set_data = n411_set_data, + .wait_for_ack = n411_wait_for_ack, +}; + +static struct platform_device *n411_device; +static int __init n411_init(void) +{ + int ret; + if (!dio_addr || !cio_addr || !c2io_addr) { + printk(KERN_WARNING "no IO addresses supplied\n"); + return -EINVAL; + } + + /* request our platform independent driver */ + request_module("hecubafb"); + + n411_device = platform_device_alloc("hecubafb", -1); + if (!n411_device) + return -ENOMEM; + + platform_device_add_data(n411_device, &n411_board, sizeof(n411_board)); + + /* this _add binds hecubafb to n411. hecubafb refcounts n411 */ + ret = platform_device_add(n411_device); + + if (ret) + platform_device_put(n411_device); + + return ret; + +} + +static void __exit n411_exit(void) +{ + platform_device_unregister(n411_device); +} + +module_init(n411_init); +module_exit(n411_exit); + +module_param(nosplash, uint, 0); +MODULE_PARM_DESC(nosplash, "Disable doing the splash screen"); +module_param(dio_addr, ulong, 0); +MODULE_PARM_DESC(dio_addr, "IO address for data, eg: 0x480"); +module_param(cio_addr, ulong, 0); +MODULE_PARM_DESC(cio_addr, "IO address for control, eg: 0x400"); +module_param(c2io_addr, ulong, 0); +MODULE_PARM_DESC(c2io_addr, "IO address for secondary control, eg: 0x408"); +module_param(splashval, ulong, 0); +MODULE_PARM_DESC(splashval, "Splash pattern: 0x00 is black, 0x01 is white"); + +MODULE_DESCRIPTION("board driver for n411 hecuba/apollo epd kit"); +MODULE_AUTHOR("Jaya Kumar"); +MODULE_LICENSE("GPL"); + diff --git a/include/video/hecubafb.h b/include/video/hecubafb.h new file mode 100644 index 00000000000..7b995233976 --- /dev/null +++ b/include/video/hecubafb.h @@ -0,0 +1,51 @@ +/* + * hecubafb.h - definitions for the hecuba framebuffer driver + * + * Copyright (C) 2008 by Jaya Kumar + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive for + * more details. + * + */ + +#ifndef _LINUX_HECUBAFB_H_ +#define _LINUX_HECUBAFB_H_ + +/* Apollo controller specific defines */ +#define APOLLO_START_NEW_IMG 0xA0 +#define APOLLO_STOP_IMG_DATA 0xA1 +#define APOLLO_DISPLAY_IMG 0xA2 +#define APOLLO_ERASE_DISPLAY 0xA3 +#define APOLLO_INIT_DISPLAY 0xA4 + +/* Hecuba interface specific defines */ +#define HCB_WUP_BIT 0x01 +#define HCB_DS_BIT 0x02 +#define HCB_RW_BIT 0x04 +#define HCB_CD_BIT 0x08 +#define HCB_ACK_BIT 0x80 + +/* struct used by hecuba. board specific stuff comes from *board */ +struct hecubafb_par { + struct fb_info *info; + struct hecuba_board *board; + void (*send_command)(struct hecubafb_par *, unsigned char); + void (*send_data)(struct hecubafb_par *, unsigned char); +}; + +/* board specific routines +board drivers can implement wait_for_ack with interrupts if desired. if +wait_for_ack is called with clear=0, then go to sleep and return when ack +goes hi or if wait_for_ack with clear=1, then return when ack goes lo */ +struct hecuba_board { + struct module *owner; + void (*remove)(struct hecubafb_par *); + void (*set_ctl)(struct hecubafb_par *, unsigned char, unsigned char); + void (*set_data)(struct hecubafb_par *, unsigned char); + void (*wait_for_ack)(struct hecubafb_par *, int); + int (*init)(struct hecubafb_par *); +}; + + +#endif |