summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
Diffstat
-rw-r--r--Documentation/hwmon/f71882fg10
-rw-r--r--drivers/hwmon/Kconfig6
-rw-r--r--drivers/hwmon/f71882fg.c86
3 files changed, 81 insertions, 21 deletions
diff --git a/Documentation/hwmon/f71882fg b/Documentation/hwmon/f71882fg
index bee4c30bc1e..a7952c2bd95 100644
--- a/Documentation/hwmon/f71882fg
+++ b/Documentation/hwmon/f71882fg
@@ -14,6 +14,10 @@ Supported chips:
Prefix: 'f71882fg'
Addresses scanned: none, address read from Super I/O config space
Datasheet: Available from the Fintek website
+ * Fintek F71889FG
+ Prefix: 'f71889fg'
+ Addresses scanned: none, address read from Super I/O config space
+ Datasheet: Should become available on the Fintek website soon
* Fintek F8000
Prefix: 'f8000'
Addresses scanned: none, address read from Super I/O config space
@@ -51,6 +55,12 @@ supported. The right one to use depends on external circuitry on the
motherboard, so the driver assumes that the BIOS set the method
properly.
+Note that the lowest numbered temperature zone trip point corresponds to
+to the border between the highest and one but highest temperature zones, and
+vica versa. So the temperature zone trip points 1-4 (or 1-2) go from high temp
+to low temp! This is how things are implemented in the IC, and the driver
+mimicks this.
+
There are 2 modes to specify the speed of the fan, PWM duty cycle (or DC
voltage) mode, where 0-100% duty cycle (0-100% of 12V) is specified. And RPM
mode where the actual RPM of the fan (as measured) is controlled and the speed
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index dd6939370f7..edf8febb5bc 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -305,12 +305,12 @@ config SENSORS_F71805F
will be called f71805f.
config SENSORS_F71882FG
- tristate "Fintek F71858FG, F71862FG, F71882FG and F8000"
+ tristate "Fintek F71858FG, F71862FG, F71882FG, F71889FG and F8000"
depends on EXPERIMENTAL
help
If you say yes here you get support for hardware monitoring
- features of the Fintek F71858FG, F71862FG/71863FG, F71882FG/F71883FG
- and F8000 Super-I/O chips.
+ features of the Fintek F71858FG, F71862FG/71863FG, F71882FG/F71883FG,
+ F71889FG and F8000 Super-I/O chips.
This driver can also be built as a module. If so, the module
will be called f71882fg.
diff --git a/drivers/hwmon/f71882fg.c b/drivers/hwmon/f71882fg.c
index 3a695f06905..a95fa4256ca 100644
--- a/drivers/hwmon/f71882fg.c
+++ b/drivers/hwmon/f71882fg.c
@@ -48,6 +48,7 @@
#define SIO_F71858_ID 0x0507 /* Chipset ID */
#define SIO_F71862_ID 0x0601 /* Chipset ID */
#define SIO_F71882_ID 0x0541 /* Chipset ID */
+#define SIO_F71889_ID 0x0723 /* Chipset ID */
#define SIO_F8000_ID 0x0581 /* Chipset ID */
#define REGION_LENGTH 8
@@ -95,12 +96,13 @@ static unsigned short force_id;
module_param(force_id, ushort, 0);
MODULE_PARM_DESC(force_id, "Override the detected device ID");
-enum chips { f71858fg, f71862fg, f71882fg, f8000 };
+enum chips { f71858fg, f71862fg, f71882fg, f71889fg, f8000 };
static const char *f71882fg_names[] = {
"f71858fg",
"f71862fg",
"f71882fg",
+ "f71889fg",
"f8000",
};
@@ -155,7 +157,7 @@ struct f71882fg_data {
u8 pwm_auto_point_hyst[2];
u8 pwm_auto_point_mapping[4];
u8 pwm_auto_point_pwm[4][5];
- u8 pwm_auto_point_temp[4][4];
+ s8 pwm_auto_point_temp[4][4];
};
/* Sysfs in */
@@ -945,7 +947,7 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev)
/* Update once every 60 seconds */
if ( time_after(jiffies, data->last_limits + 60 * HZ ) ||
!data->valid) {
- if (data->type == f71882fg) {
+ if (data->type == f71882fg || data->type == f71889fg) {
data->in1_max =
f71882fg_read8(data, F71882FG_REG_IN1_HIGH);
data->in_beep =
@@ -967,7 +969,8 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev)
F71882FG_REG_TEMP_HYST(1));
}
- if (data->type == f71862fg || data->type == f71882fg) {
+ if (data->type == f71862fg || data->type == f71882fg ||
+ data->type == f71889fg) {
data->fan_beep = f71882fg_read8(data,
F71882FG_REG_FAN_BEEP);
data->temp_beep = f71882fg_read8(data,
@@ -977,15 +980,33 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev)
data->temp_type[2] = (reg & 0x04) ? 2 : 4;
data->temp_type[3] = (reg & 0x08) ? 2 : 4;
}
- reg2 = f71882fg_read8(data, F71882FG_REG_PECI);
- if ((reg2 & 0x03) == 0x01)
- data->temp_type[1] = 6 /* PECI */;
- else if ((reg2 & 0x03) == 0x02)
- data->temp_type[1] = 5 /* AMDSI */;
- else if (data->type == f71862fg || data->type == f71882fg)
- data->temp_type[1] = (reg & 0x02) ? 2 : 4;
- else
- data->temp_type[1] = 2; /* Only supports BJT */
+ /* Determine temp index 1 sensor type */
+ if (data->type == f71889fg) {
+ reg2 = f71882fg_read8(data, F71882FG_REG_START);
+ switch ((reg2 & 0x60) >> 5) {
+ case 0x00: /* BJT / Thermistor */
+ data->temp_type[1] = (reg & 0x02) ? 2 : 4;
+ break;
+ case 0x01: /* AMDSI */
+ data->temp_type[1] = 5;
+ break;
+ case 0x02: /* PECI */
+ case 0x03: /* Ibex Peak ?? Report as PECI for now */
+ data->temp_type[1] = 6;
+ break;
+ }
+ } else {
+ reg2 = f71882fg_read8(data, F71882FG_REG_PECI);
+ if ((reg2 & 0x03) == 0x01)
+ data->temp_type[1] = 6; /* PECI */
+ else if ((reg2 & 0x03) == 0x02)
+ data->temp_type[1] = 5; /* AMDSI */
+ else if (data->type == f71862fg ||
+ data->type == f71882fg)
+ data->temp_type[1] = (reg & 0x02) ? 2 : 4;
+ else /* f71858fg and f8000 only support BJT */
+ data->temp_type[1] = 2;
+ }
data->pwm_enable = f71882fg_read8(data,
F71882FG_REG_PWM_ENABLE);
@@ -1062,7 +1083,7 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev)
if (data->type == f8000)
data->fan[3] = f71882fg_read16(data,
F71882FG_REG_FAN(3));
- if (data->type == f71882fg)
+ if (data->type == f71882fg || data->type == f71889fg)
data->in_status = f71882fg_read8(data,
F71882FG_REG_IN_STATUS);
for (nr = 0; nr < nr_ins; nr++)
@@ -1780,7 +1801,11 @@ static ssize_t store_pwm_auto_point_temp(struct device *dev,
int pwm = to_sensor_dev_attr_2(devattr)->index;
int point = to_sensor_dev_attr_2(devattr)->nr;
long val = simple_strtol(buf, NULL, 10) / 1000;
- val = SENSORS_LIMIT(val, 0, 255);
+
+ if (data->type == f71889fg)
+ val = SENSORS_LIMIT(val, -128, 127);
+ else
+ val = SENSORS_LIMIT(val, 0, 127);
mutex_lock(&data->update_lock);
f71882fg_write8(data, F71882FG_REG_POINT_TEMP(pwm, point), val);
@@ -1871,6 +1896,7 @@ static int __devinit f71882fg_probe(struct platform_device *pdev)
ARRAY_SIZE(f71858fg_in_temp_attr));
break;
case f71882fg:
+ case f71889fg:
err = f71882fg_create_sysfs_files(pdev,
fxxxx_in1_alarm_attr,
ARRAY_SIZE(fxxxx_in1_alarm_attr));
@@ -1908,6 +1934,7 @@ static int __devinit f71882fg_probe(struct platform_device *pdev)
err = (data->pwm_enable & 0x15) != 0x15;
break;
case f71882fg:
+ case f71889fg:
err = 0;
break;
case f8000:
@@ -1927,7 +1954,8 @@ static int __devinit f71882fg_probe(struct platform_device *pdev)
if (err)
goto exit_unregister_sysfs;
- if (data->type == f71862fg || data->type == f71882fg) {
+ if (data->type == f71862fg || data->type == f71882fg ||
+ data->type == f71889fg) {
err = f71882fg_create_sysfs_files(pdev,
fxxxx_fan_beep_attr, nr_fans);
if (err)
@@ -1950,6 +1978,22 @@ static int __devinit f71882fg_probe(struct platform_device *pdev)
f8000_auto_pwm_attr,
ARRAY_SIZE(f8000_auto_pwm_attr));
break;
+ case f71889fg:
+ for (i = 0; i < nr_fans; i++) {
+ data->pwm_auto_point_mapping[i] =
+ f71882fg_read8(data,
+ F71882FG_REG_POINT_MAPPING(i));
+ if (data->pwm_auto_point_mapping[i] & 0x80)
+ break;
+ }
+ if (i != nr_fans) {
+ dev_warn(&pdev->dev,
+ "Auto pwm controlled by raw digital "
+ "data, disabling pwm auto_point "
+ "sysfs attributes\n");
+ break;
+ }
+ /* fall through */
default: /* f71858fg / f71882fg */
err = f71882fg_create_sysfs_files(pdev,
&fxxxx_auto_pwm_attr[0][0],
@@ -2006,6 +2050,7 @@ static int f71882fg_remove(struct platform_device *pdev)
ARRAY_SIZE(f71858fg_in_temp_attr));
break;
case f71882fg:
+ case f71889fg:
f71882fg_remove_sysfs_files(pdev,
fxxxx_in1_alarm_attr,
ARRAY_SIZE(fxxxx_in1_alarm_attr));
@@ -2027,7 +2072,8 @@ static int f71882fg_remove(struct platform_device *pdev)
f71882fg_remove_sysfs_files(pdev, &fxxxx_fan_attr[0][0],
ARRAY_SIZE(fxxxx_fan_attr[0]) * nr_fans);
- if (data->type == f71862fg || data->type == f71882fg)
+ if (data->type == f71862fg || data->type == f71882fg ||
+ data->type == f71889fg)
f71882fg_remove_sysfs_files(pdev,
fxxxx_fan_beep_attr, nr_fans);
@@ -2082,11 +2128,15 @@ static int __init f71882fg_find(int sioaddr, unsigned short *address,
case SIO_F71882_ID:
sio_data->type = f71882fg;
break;
+ case SIO_F71889_ID:
+ sio_data->type = f71889fg;
+ break;
case SIO_F8000_ID:
sio_data->type = f8000;
break;
default:
- printk(KERN_INFO DRVNAME ": Unsupported Fintek device\n");
+ printk(KERN_INFO DRVNAME ": Unsupported Fintek device: %04x\n",
+ (unsigned int)devid);
goto exit;
}
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-11-17 17:08:20 +0000