diff options
50 files changed, 2129 insertions, 2797 deletions
diff --git a/Documentation/i2c/chips/max6875 b/Documentation/i2c/chips/max6875 index a0cd8af2f40..10ca43cd1a7 100644 --- a/Documentation/i2c/chips/max6875 +++ b/Documentation/i2c/chips/max6875 @@ -49,7 +49,7 @@ $ modprobe max6875 force=0,0x50 The MAX6874/MAX6875 ignores address bit 0, so this driver attaches to multiple addresses. For example, for address 0x50, it also reserves 0x51. -The even-address instance is called 'max6875', the odd one is 'max6875 subclient'. +The even-address instance is called 'max6875', the odd one is 'dummy'. Programming the chip using i2c-dev diff --git a/Documentation/i2c/chips/pca9539 b/Documentation/i2c/chips/pca9539 index 1d81c530c4a..6aff890088b 100644 --- a/Documentation/i2c/chips/pca9539 +++ b/Documentation/i2c/chips/pca9539 @@ -7,7 +7,7 @@ drivers/gpio/pca9539.c instead. Supported chips: * Philips PCA9539 Prefix: 'pca9539' - Addresses scanned: 0x74 - 0x77 + Addresses scanned: none Datasheet: http://www.semiconductors.philips.com/acrobat/datasheets/PCA9539_2.pdf @@ -23,6 +23,14 @@ The input sense can also be inverted. The 16 lines are split between two bytes. +Detection +--------- + +The PCA9539 is difficult to detect and not commonly found in PC machines, +so you have to pass the I2C bus and address of the installed PCA9539 +devices explicitly to the driver at load time via the force=... parameter. + + Sysfs entries ------------- diff --git a/Documentation/i2c/chips/pcf8574 b/Documentation/i2c/chips/pcf8574 index 5c1ad1376b6..235815c075f 100644 --- a/Documentation/i2c/chips/pcf8574 +++ b/Documentation/i2c/chips/pcf8574 @@ -4,13 +4,13 @@ Kernel driver pcf8574 Supported chips: * Philips PCF8574 Prefix: 'pcf8574' - Addresses scanned: I2C 0x20 - 0x27 + Addresses scanned: none Datasheet: Publicly available at the Philips Semiconductors website http://www.semiconductors.philips.com/pip/PCF8574P.html * Philips PCF8574A Prefix: 'pcf8574a' - Addresses scanned: I2C 0x38 - 0x3f + Addresses scanned: none Datasheet: Publicly available at the Philips Semiconductors website http://www.semiconductors.philips.com/pip/PCF8574P.html @@ -38,12 +38,10 @@ For more informations see the datasheet. Accessing PCF8574(A) via /sys interface ------------------------------------- -! Be careful ! The PCF8574(A) is plainly impossible to detect ! Stupid chip. -So every chip with address in the interval [20..27] and [38..3f] are -detected as PCF8574(A). If you have other chips in this address -range, the workaround is to load this module after the one -for your others chips. +So, you have to pass the I2C bus and address of the installed PCF857A +and PCF8574A devices explicitly to the driver at load time via the +force=... parameter. On detection (i.e. insmod, modprobe et al.), directories are being created for each detected PCF8574(A): diff --git a/Documentation/i2c/chips/pcf8575 b/Documentation/i2c/chips/pcf8575 index 25f5698a61c..40b268eb276 100644 --- a/Documentation/i2c/chips/pcf8575 +++ b/Documentation/i2c/chips/pcf8575 @@ -40,12 +40,9 @@ Detection --------- There is no method known to detect whether a chip on a given I2C address is -a PCF8575 or whether it is any other I2C device. So there are two alternatives -to let the driver find the installed PCF8575 devices: -- Load this driver after any other I2C driver for I2C devices with addresses - in the range 0x20 .. 0x27. -- Pass the I2C bus and address of the installed PCF8575 devices explicitly to - the driver at load time via the probe=... or force=... parameters. +a PCF8575 or whether it is any other I2C device, so you have to pass the I2C +bus and address of the installed PCF8575 devices explicitly to the driver at +load time via the force=... parameter. /sys interface -------------- diff --git a/drivers/hwmon/ad7418.c b/drivers/hwmon/ad7418.c index 466b9ee9279..f97b5b35687 100644 --- a/drivers/hwmon/ad7418.c +++ b/drivers/hwmon/ad7418.c @@ -23,12 +23,9 @@ #include "lm75.h" -#define DRV_VERSION "0.3" +#define DRV_VERSION "0.4" -/* Addresses to scan */ -static const unsigned short normal_i2c[] = { 0x28, I2C_CLIENT_END }; -/* Insmod parameters */ -I2C_CLIENT_INSMOD_3(ad7416, ad7417, ad7418); +enum chips { ad7416, ad7417, ad7418 }; /* AD7418 registers */ #define AD7418_REG_TEMP_IN 0x00 @@ -46,7 +43,6 @@ static const u8 AD7418_REG_TEMP[] = { AD7418_REG_TEMP_IN, AD7418_REG_TEMP_OS }; struct ad7418_data { - struct i2c_client client; struct device *hwmon_dev; struct attribute_group attrs; enum chips type; @@ -58,16 +54,25 @@ struct ad7418_data { u16 in[4]; }; -static int ad7418_attach_adapter(struct i2c_adapter *adapter); -static int ad7418_detect(struct i2c_adapter *adapter, int address, int kind); -static int ad7418_detach_client(struct i2c_client *client); +static int ad7418_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int ad7418_remove(struct i2c_client *client); + +static const struct i2c_device_id ad7418_id[] = { + { "ad7416", ad7416 }, + { "ad7417", ad7417 }, + { "ad7418", ad7418 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, ad7418_id); static struct i2c_driver ad7418_driver = { .driver = { .name = "ad7418", }, - .attach_adapter = ad7418_attach_adapter, - .detach_client = ad7418_detach_client, + .probe = ad7418_probe, + .remove = ad7418_remove, + .id_table = ad7418_id, }; /* All registers are word-sized, except for the configuration registers. @@ -192,13 +197,6 @@ static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, show_adc, NULL, 1); static SENSOR_DEVICE_ATTR(in3_input, S_IRUGO, show_adc, NULL, 2); static SENSOR_DEVICE_ATTR(in4_input, S_IRUGO, show_adc, NULL, 3); -static int ad7418_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, ad7418_detect); -} - static struct attribute *ad7416_attributes[] = { &sensor_dev_attr_temp1_max.dev_attr.attr, &sensor_dev_attr_temp1_max_hyst.dev_attr.attr, @@ -225,98 +223,46 @@ static struct attribute *ad7418_attributes[] = { NULL }; -static int ad7418_detect(struct i2c_adapter *adapter, int address, int kind) +static int ad7418_probe(struct i2c_client *client, + const struct i2c_device_id *id) { - struct i2c_client *client; + struct i2c_adapter *adapter = client->adapter; struct ad7418_data *data; - int err = 0; + int err; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA | - I2C_FUNC_SMBUS_WORD_DATA)) + I2C_FUNC_SMBUS_WORD_DATA)) { + err = -EOPNOTSUPP; goto exit; + } if (!(data = kzalloc(sizeof(struct ad7418_data), GFP_KERNEL))) { err = -ENOMEM; goto exit; } - client = &data->client; - client->addr = address; - client->adapter = adapter; - client->driver = &ad7418_driver; - i2c_set_clientdata(client, data); mutex_init(&data->lock); - - /* AD7418 has a curious behaviour on registers 6 and 7. They - * both always read 0xC071 and are not documented on the datasheet. - * We use them to detect the chip. - */ - if (kind <= 0) { - int reg, reg6, reg7; - - /* the AD7416 lies within this address range, but I have - * no means to check. - */ - if (address >= 0x48 && address <= 0x4f) { - /* XXX add tests for AD7416 here */ - /* data->type = ad7416; */ - } - /* here we might have AD7417 or AD7418 */ - else if (address >= 0x28 && address <= 0x2f) { - reg6 = i2c_smbus_read_word_data(client, 0x06); - reg7 = i2c_smbus_read_word_data(client, 0x07); - - if (address == 0x28 && reg6 == 0xC071 && reg7 == 0xC071) - data->type = ad7418; - - /* XXX add tests for AD7417 here */ - - - /* both AD7417 and AD7418 have bits 0-5 of - * the CONF2 register at 0 - */ - reg = i2c_smbus_read_byte_data(client, - AD7418_REG_CONF2); - if (reg & 0x3F) - data->type = any_chip; /* detection failed */ - } - } else { - dev_dbg(&adapter->dev, "detection forced\n"); - } - - if (kind > 0) - data->type = kind; - else if (kind < 0 && data->type == any_chip) { - err = -ENODEV; - goto exit_free; - } + data->type = id->driver_data; switch (data->type) { - case any_chip: case ad7416: data->adc_max = 0; data->attrs.attrs = ad7416_attributes; - strlcpy(client->name, "ad7416", I2C_NAME_SIZE); break; case ad7417: data->adc_max = 4; data->attrs.attrs = ad7417_attributes; - strlcpy(client->name, "ad7417", I2C_NAME_SIZE); break; case ad7418: data->adc_max = 1; data->attrs.attrs = ad7418_attributes; - strlcpy(client->name, "ad7418", I2C_NAME_SIZE); break; } - if ((err = i2c_attach_client(client))) - goto exit_free; - dev_info(&client->dev, "%s chip found\n", client->name); /* Initialize the AD7418 chip */ @@ -324,7 +270,7 @@ static int ad7418_detect(struct i2c_adapter *adapter, int address, int kind) /* Register sysfs hooks */ if ((err = sysfs_create_group(&client->dev.kobj, &data->attrs))) - goto exit_detach; + goto exit_free; data->hwmon_dev = hwmon_device_register(&client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -336,20 +282,17 @@ static int ad7418_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove: sysfs_remove_group(&client->dev.kobj, &data->attrs); -exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: return err; } -static int ad7418_detach_client(struct i2c_client *client) +static int ad7418_remove(struct i2c_client *client) { struct ad7418_data *data = i2c_get_clientdata(client); hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &data->attrs); - i2c_detach_client(client); kfree(data); return 0; } diff --git a/drivers/hwmon/adm1021.c b/drivers/hwmon/adm1021.c index ecbf69484bf..b11e06f644b 100644 --- a/drivers/hwmon/adm1021.c +++ b/drivers/hwmon/adm1021.c @@ -78,7 +78,6 @@ clearing it. Weird, ey? --Phil */ /* Each client has this additional data */ struct adm1021_data { - struct i2c_client client; struct device *hwmon_dev; enum chips type; @@ -98,23 +97,42 @@ struct adm1021_data { u8 remote_temp_offset_prec; }; -static int adm1021_attach_adapter(struct i2c_adapter *adapter); -static int adm1021_detect(struct i2c_adapter *adapter, int address, int kind); +static int adm1021_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int adm1021_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); static void adm1021_init_client(struct i2c_client *client); -static int adm1021_detach_client(struct i2c_client *client); +static int adm1021_remove(struct i2c_client *client); static struct adm1021_data *adm1021_update_device(struct device *dev); /* (amalysh) read only mode, otherwise any limit's writing confuse BIOS */ static int read_only; +static const struct i2c_device_id adm1021_id[] = { + { "adm1021", adm1021 }, + { "adm1023", adm1023 }, + { "max1617", max1617 }, + { "max1617a", max1617a }, + { "thmc10", thmc10 }, + { "lm84", lm84 }, + { "gl523sm", gl523sm }, + { "mc1066", mc1066 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, adm1021_id); + /* This is the driver that will be inserted */ static struct i2c_driver adm1021_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "adm1021", }, - .attach_adapter = adm1021_attach_adapter, - .detach_client = adm1021_detach_client, + .probe = adm1021_probe, + .remove = adm1021_remove, + .id_table = adm1021_id, + .detect = adm1021_detect, + .address_data = &addr_data, }; static ssize_t show_temp(struct device *dev, @@ -216,13 +234,6 @@ static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, 2); static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL); -static int adm1021_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, adm1021_detect); -} - static struct attribute *adm1021_attributes[] = { &sensor_dev_attr_temp1_max.dev_attr.attr, &sensor_dev_attr_temp1_min.dev_attr.attr, @@ -243,36 +254,21 @@ static const struct attribute_group adm1021_group = { .attrs = adm1021_attributes, }; -static int adm1021_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int adm1021_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { + struct i2c_adapter *adapter = client->adapter; int i; - struct i2c_client *client; - struct adm1021_data *data; - int err = 0; const char *type_name = ""; int conv_rate, status, config; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { pr_debug("adm1021: detect failed, " "smbus byte data not supported!\n"); - goto error0; - } - - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access adm1021 register values. */ - - if (!(data = kzalloc(sizeof(struct adm1021_data), GFP_KERNEL))) { - pr_debug("adm1021: detect failed, kzalloc failed!\n"); - err = -ENOMEM; - goto error0; + return -ENODEV; } - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &adm1021_driver; status = i2c_smbus_read_byte_data(client, ADM1021_REG_STATUS); conv_rate = i2c_smbus_read_byte_data(client, ADM1021_REG_CONV_RATE_R); @@ -284,8 +280,7 @@ static int adm1021_detect(struct i2c_adapter *adapter, int address, int kind) || (conv_rate & 0xF8) != 0x00) { pr_debug("adm1021: detect failed, " "chip not detected!\n"); - err = -ENODEV; - goto error1; + return -ENODEV; } } @@ -336,24 +331,36 @@ static int adm1021_detect(struct i2c_adapter *adapter, int address, int kind) type_name = "mc1066"; } pr_debug("adm1021: Detected chip %s at adapter %d, address 0x%02x.\n", - type_name, i2c_adapter_id(adapter), address); + type_name, i2c_adapter_id(adapter), client->addr); + strlcpy(info->type, type_name, I2C_NAME_SIZE); - /* Fill in the remaining client fields */ - strlcpy(client->name, type_name, I2C_NAME_SIZE); - data->type = kind; - mutex_init(&data->update_lock); + return 0; +} - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto error1; +static int adm1021_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct adm1021_data *data; + int err; + + data = kzalloc(sizeof(struct adm1021_data), GFP_KERNEL); + if (!data) { + pr_debug("adm1021: detect failed, kzalloc failed!\n"); + err = -ENOMEM; + goto error0; + } + + i2c_set_clientdata(client, data); + data->type = id->driver_data; + mutex_init(&data->update_lock); /* Initialize the ADM1021 chip */ - if (kind != lm84 && !read_only) + if (data->type != lm84 && !read_only) adm1021_init_client(client); /* Register sysfs hooks */ if ((err = sysfs_create_group(&client->dev.kobj, &adm1021_group))) - goto error2; + goto error1; data->hwmon_dev = hwmon_device_register(&client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -365,8 +372,6 @@ static int adm1021_detect(struct i2c_adapter *adapter, int address, int kind) error3: sysfs_remove_group(&client->dev.kobj, &adm1021_group); -error2: - i2c_detach_client(client); error1: kfree(data); error0: @@ -382,17 +387,13 @@ static void adm1021_init_client(struct i2c_client *client) i2c_smbus_write_byte_data(client, ADM1021_REG_CONV_RATE_W, 0x04); } -static int adm1021_detach_client(struct i2c_client *client) +static int adm1021_remove(struct i2c_client *client) { struct adm1021_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &adm1021_group); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } diff --git a/drivers/hwmon/adm1025.c b/drivers/hwmon/adm1025.c index 1d76de7d75c..4db04d603ec 100644 --- a/drivers/hwmon/adm1025.c +++ b/drivers/hwmon/adm1025.c @@ -2,7 +2,7 @@ * adm1025.c * * Copyright (C) 2000 Chen-Yuan Wu <gwu@esoft.com> - * Copyright (C) 2003-2004 Jean Delvare <khali@linux-fr.org> + * Copyright (C) 2003-2008 Jean Delvare <khali@linux-fr.org> * * The ADM1025 is a sensor chip made by Analog Devices. It reports up to 6 * voltages (including its own power source) and up to two temperatures @@ -109,22 +109,35 @@ static const int in_scale[6] = { 2500, 2250, 3300, 5000, 12000, 3300 }; * Functions declaration */ -static int adm1025_attach_adapter(struct i2c_adapter *adapter); -static int adm1025_detect(struct i2c_adapter *adapter, int address, int kind); +static int adm1025_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int adm1025_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); static void adm1025_init_client(struct i2c_client *client); -static int adm1025_detach_client(struct i2c_client *client); +static int adm1025_remove(struct i2c_client *client); static struct adm1025_data *adm1025_update_device(struct device *dev); /* * Driver data (common to all clients) */ +static const struct i2c_device_id adm1025_id[] = { + { "adm1025", adm1025 }, + { "ne1619", ne1619 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, adm1025_id); + static struct i2c_driver adm1025_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "adm1025", }, - .attach_adapter = adm1025_attach_adapter, - .detach_client = adm1025_detach_client, + .probe = adm1025_probe, + .remove = adm1025_remove, + .id_table = adm1025_id, + .detect = adm1025_detect, + .address_data = &addr_data, }; /* @@ -132,7 +145,6 @@ static struct i2c_driver adm1025_driver = { */ struct adm1025_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* zero until following fields are valid */ @@ -344,13 +356,6 @@ static DEVICE_ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm, set_vrm); * Real code */ -static int adm1025_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, adm1025_detect); -} - static struct attribute *adm1025_attributes[] = { &sensor_dev_attr_in0_input.dev_attr.attr, &sensor_dev_attr_in1_input.dev_attr.attr, @@ -403,31 +408,16 @@ static const struct attribute_group adm1025_group_in4 = { .attrs = adm1025_attributes_in4, }; -/* - * The following function does more than just detection. If detection - * succeeds, it also registers the new chip. - */ -static int adm1025_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int adm1025_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - struct i2c_client *client; - struct adm1025_data *data; - int err = 0; + struct i2c_adapter *adapter = client->adapter; const char *name = ""; u8 config; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct adm1025_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &adm1025_driver; + return -ENODEV; /* * Now we do the remaining detection. A negative kind means that @@ -448,8 +438,8 @@ static int adm1025_detect(struct i2c_adapter *adapter, int address, int kind) ADM1025_REG_STATUS2) & 0xBC) != 0x00) { dev_dbg(&adapter->dev, "ADM1025 detection failed at 0x%02x.\n", - address); - goto exit_free; + client->addr); + return -ENODEV; } } @@ -465,7 +455,7 @@ static int adm1025_detect(struct i2c_adapter *adapter, int address, int kind) } } else if (man_id == 0xA1) { /* Philips */ - if (address != 0x2E + if (client->addr != 0x2E && (chip_id & 0xF0) == 0x20) { /* NE1619 */ kind = ne1619; } @@ -475,7 +465,7 @@ static int adm1025_detect(struct i2c_adapter *adapter, int address, int kind) dev_info(&adapter->dev, "Unsupported chip (man_id=0x%02X, " "chip_id=0x%02X).\n", man_id, chip_id); - goto exit_free; + return -ENODEV; } } @@ -484,23 +474,36 @@ static int adm1025_detect(struct i2c_adapter *adapter, int address, int kind) } else if (kind == ne1619) { name = "ne1619"; } + strlcpy(info->type, name, I2C_NAME_SIZE); - /* We can fill in the remaining client fields */ - strlcpy(client->name, name, I2C_NAME_SIZE); - mutex_init(&data->update_lock); + return 0; +} - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_free; +static int adm1025_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct adm1025_data *data; + int err; + u8 config; + + data = kzalloc(sizeof(struct adm1025_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); /* Initialize the ADM1025 chip */ adm1025_init_client(client); /* Register sysfs hooks */ if ((err = sysfs_create_group(&client->dev.kobj, &adm1025_group))) - goto exit_detach; + goto exit_free; /* Pin 11 is either in4 (+12V) or VID4 */ + config = i2c_smbus_read_byte_data(client, ADM1025_REG_CONFIG); if (!(config & 0x20)) { if ((err = sysfs_create_group(&client->dev.kobj, &adm1025_group_in4))) @@ -518,8 +521,6 @@ static int adm1025_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove: sysfs_remove_group(&client->dev.kobj, &adm1025_group); sysfs_remove_group(&client->dev.kobj, &adm1025_group_in4); -exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: @@ -568,18 +569,14 @@ static void adm1025_init_client(struct i2c_client *client) (reg&0x7E)|0x01); } -static int adm1025_detach_client(struct i2c_client *client) +static int adm1025_remove(struct i2c_client *client) { struct adm1025_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &adm1025_group); sysfs_remove_group(&client->dev.kobj, &adm1025_group_in4); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } diff --git a/drivers/hwmon/adm1026.c b/drivers/hwmon/adm1026.c index 904c6ce9d83..7fe2441fc84 100644 --- a/drivers/hwmon/adm1026.c +++ b/drivers/hwmon/adm1026.c @@ -259,7 +259,6 @@ struct pwm_data { }; struct adm1026_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; @@ -293,10 +292,11 @@ struct adm1026_data { u8 config3; /* Register value */ }; -static int adm1026_attach_adapter(struct i2c_adapter *adapter); -static int adm1026_detect(struct i2c_adapter *adapter, int address, - int kind); -static int adm1026_detach_client(struct i2c_client *client); +static int adm1026_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int adm1026_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int adm1026_remove(struct i2c_client *client); static int adm1026_read_value(struct i2c_client *client, u8 reg); static int adm1026_write_value(struct i2c_client *client, u8 reg, int value); static void adm1026_print_gpio(struct i2c_client *client); @@ -305,22 +305,24 @@ static struct adm1026_data *adm1026_update_device(struct device *dev); static void adm1026_init_client(struct i2c_client *client); +static const struct i2c_device_id adm1026_id[] = { + { "adm1026", adm1026 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, adm1026_id); + static struct i2c_driver adm1026_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "adm1026", }, - .attach_adapter = adm1026_attach_adapter, - .detach_client = adm1026_detach_client, + .probe = adm1026_probe, + .remove = adm1026_remove, + .id_table = adm1026_id, + .detect = adm1026_detect, + .address_data = &addr_data, }; -static int adm1026_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) { - return 0; - } - return i2c_probe(adapter, &addr_data, adm1026_detect); -} - static int adm1026_read_value(struct i2c_client *client, u8 reg) { int res; @@ -1647,48 +1649,32 @@ static const struct attribute_group adm1026_group_in8_9 = { .attrs = adm1026_attributes_in8_9, }; -static int adm1026_detect(struct i2c_adapter *adapter, int address, - int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int adm1026_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { + struct i2c_adapter *adapter = client->adapter; + int address = client->addr; int company, verstep; - struct i2c_client *client; - struct adm1026_data *data; - int err = 0; - const char *type_name = ""; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { /* We need to be able to do byte I/O */ - goto exit; + return -ENODEV; }; - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access adm1026_{read,write}_value. */ - - if (!(data = kzalloc(sizeof(struct adm1026_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &adm1026_driver; - /* Now, we do the remaining detection. */ company = adm1026_read_value(client, ADM1026_REG_COMPANY); verstep = adm1026_read_value(client, ADM1026_REG_VERSTEP); - dev_dbg(&client->dev, "Detecting device at %d,0x%02x with" + dev_dbg(&adapter->dev, "Detecting device at %d,0x%02x with" " COMPANY: 0x%02x and VERSTEP: 0x%02x\n", i2c_adapter_id(client->adapter), client->addr, company, verstep); /* If auto-detecting, Determine the chip type. */ if (kind <= 0) { - dev_dbg(&client->dev, "Autodetecting device at %d,0x%02x " + dev_dbg(&adapter->dev, "Autodetecting device at %d,0x%02x " "...\n", i2c_adapter_id(adapter), address); if (company == ADM1026_COMPANY_ANALOG_DEV && verstep == ADM1026_VERSTEP_ADM1026) { @@ -1704,7 +1690,7 @@ static int adm1026_detect(struct i2c_adapter *adapter, int address, verstep); kind = any_chip; } else { - dev_dbg(&client->dev, ": Autodetection " + dev_dbg(&adapter->dev, ": Autodetection " "failed\n"); /* Not an ADM1026 ... */ if (kind == 0) { /* User used force=x,y */ @@ -1713,33 +1699,29 @@ static int adm1026_detect(struct i2c_adapter *adapter, int address, "force_adm1026.\n", i2c_adapter_id(adapter), address); } - goto exitfree; + return -ENODEV; } } + strlcpy(info->type, "adm1026", I2C_NAME_SIZE); - /* Fill in the chip specific driver values */ - switch (kind) { - case any_chip : - type_name = "adm1026"; - break; - case adm1026 : - type_name = "adm1026"; - break; - default : - dev_err(&adapter->dev, ": Internal error, invalid " - "kind (%d)!\n", kind); - err = -EFAULT; - goto exitfree; + return 0; +} + +static int adm1026_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct adm1026_data *data; + int err; + + data = kzalloc(sizeof(struct adm1026_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; } - strlcpy(client->name, type_name, I2C_NAME_SIZE); - /* Fill in the remaining client fields */ + i2c_set_clientdata(client, data); mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exitfree; - /* Set the VRM version */ data->vrm = vid_which_vrm(); @@ -1748,7 +1730,7 @@ static int adm1026_detect(struct i2c_adapter *adapter, int address, /* Register sysfs hooks */ if ((err = sysfs_create_group(&client->dev.kobj, &adm1026_group))) - goto exitdetach; + goto exitfree; if (data->config1 & CFG1_AIN8_9) err = sysfs_create_group(&client->dev.kobj, &adm1026_group_in8_9); @@ -1773,15 +1755,13 @@ exitremove: sysfs_remove_group(&client->dev.kobj, &adm1026_group_in8_9); else sysfs_remove_group(&client->dev.kobj, &adm1026_group_temp3); -exitdetach: - i2c_detach_client(client); exitfree: kfree(data); exit: return err; } -static int adm1026_detach_client(struct i2c_client *client) +static int adm1026_remove(struct i2c_client *client) { struct adm1026_data *data = i2c_get_clientdata(client); hwmon_device_unregister(data->hwmon_dev); @@ -1790,7 +1770,6 @@ static int adm1026_detach_client(struct i2c_client *client) sysfs_remove_group(&client->dev.kobj, &adm1026_group_in8_9); else sysfs_remove_group(&client->dev.kobj, &adm1026_group_temp3); - i2c_detach_client(client); kfree(data); return 0; } diff --git a/drivers/hwmon/adm1029.c b/drivers/hwmon/adm1029.c index 2c6608d453c..ba84ca5923f 100644 --- a/drivers/hwmon/adm1029.c +++ b/drivers/hwmon/adm1029.c @@ -115,9 +115,11 @@ static const u8 ADM1029_REG_FAN_DIV[] = { * Functions declaration */ -static int adm1029_attach_adapter(struct i2c_adapter *adapter); -static int adm1029_detect(struct i2c_adapter *adapter, int address, int kind); -static int adm1029_detach_client(struct i2c_client *client); +static int adm1029_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int adm1029_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int adm1029_remove(struct i2c_client *client); static struct adm1029_data *adm1029_update_device(struct device *dev); static int adm1029_init_client(struct i2c_client *client); @@ -125,12 +127,22 @@ static int adm1029_init_client(struct i2c_client *client); * Driver data (common to all clients) */ +static const struct i2c_device_id adm1029_id[] = { + { "adm1029", adm1029 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, adm1029_id); + static struct i2c_driver adm1029_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "adm1029", }, - .attach_adapter = adm1029_attach_adapter, - .detach_client = adm1029_detach_client, + .probe = adm1029_probe, + .remove = adm1029_remove, + .id_table = adm1029_id, + .detect = adm1029_detect, + .address_data = &addr_data, }; /* @@ -138,7 +150,6 @@ static struct i2c_driver adm1029_driver = { */ struct adm1029_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* zero until following fields are valid */ @@ -284,37 +295,14 @@ static const struct attribute_group adm1029_group = { * Real code */ -static int adm1029_attach_adapter(struct i2c_adapter *adapter) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int adm1029_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, adm1029_detect); -} + struct i2c_adapter *adapter = client->adapter; -/* - * The following function does more than just detection. If detection - * succeeds, it also registers the new chip. - */ - -static int adm1029_detect(struct i2c_adapter *adapter, int address, int kind) -{ - struct i2c_client *client; - struct adm1029_data *data; - int err = 0; - const char *name = ""; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct adm1029_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &adm1029_driver; + return -ENODEV; /* Now we do the detection and identification. A negative kind * means that the driver was loaded with no force parameter @@ -362,32 +350,41 @@ static int adm1029_detect(struct i2c_adapter *adapter, int address, int kind) if (kind <= 0) { /* identification failed */ pr_debug("adm1029: Unsupported chip (man_id=0x%02X, " "chip_id=0x%02X)\n", man_id, chip_id); - goto exit_free; + return -ENODEV; } } + strlcpy(info->type, "adm1029", I2C_NAME_SIZE); - if (kind == adm1029) { - name = "adm1029"; + return 0; +} + +static int adm1029_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct adm1029_data *data; + int err; + + data = kzalloc(sizeof(struct adm1029_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; } - /* We can fill in the remaining client fields */ - strlcpy(client->name, name, I2C_NAME_SIZE); + i2c_set_clientdata(client, data); mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_free; - /* * Initialize the ADM1029 chip * Check config register */ - if (adm1029_init_client(client) == 0) - goto exit_detach; + if (adm1029_init_client(client) == 0) { + err = -ENODEV; + goto exit_free; + } /* Register sysfs hooks */ if ((err = sysfs_create_group(&client->dev.kobj, &adm1029_group))) - goto exit_detach; + goto exit_free; data->hwmon_dev = hwmon_device_register(&client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -399,8 +396,6 @@ static int adm1029_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove_files: sysfs_remove_group(&client->dev.kobj, &adm1029_group); - exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: @@ -424,17 +419,13 @@ static int adm1029_init_client(struct i2c_client *client) return 1; } -static int adm1029_detach_client(struct i2c_client *client) +static int adm1029_remove(struct i2c_client *client) { struct adm1029_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &adm1029_group); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } diff --git a/drivers/hwmon/adm1031.c b/drivers/hwmon/adm1031.c index 2bffcab7dc9..789441830cd 100644 --- a/drivers/hwmon/adm1031.c +++ b/drivers/hwmon/adm1031.c @@ -70,7 +70,6 @@ typedef u8 auto_chan_table_t[8][2]; /* Each client has this additional data */ struct adm1031_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; int chip_type; @@ -99,19 +98,32 @@ struct adm1031_data { s8 temp_crit[3]; }; -static int adm1031_attach_adapter(struct i2c_adapter *adapter); -static int adm1031_detect(struct i2c_adapter *adapter, int address, int kind); +static int adm1031_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int adm1031_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); static void adm1031_init_client(struct i2c_client *client); -static int adm1031_detach_client(struct i2c_client *client); +static int adm1031_remove(struct i2c_client *client); static struct adm1031_data *adm1031_update_device(struct device *dev); +static const struct i2c_device_id adm1031_id[] = { + { "adm1030", adm1030 }, + { "adm1031", adm1031 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, adm1031_id); + /* This is the driver that will be inserted */ static struct i2c_driver adm1031_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "adm1031", }, - .attach_adapter = adm1031_attach_adapter, - .detach_client = adm1031_detach_client, + .probe = adm1031_probe, + .remove = adm1031_remove, + .id_table = adm1031_id, + .detect = adm1031_detect, + .address_data = &addr_data, }; static inline u8 adm1031_read_value(struct i2c_client *client, u8 reg) @@ -693,13 +705,6 @@ static SENSOR_DEVICE_ATTR(temp3_crit_alarm, S_IRUGO, show_alarm, NULL, 12); static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_alarm, NULL, 13); static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, 14); -static int adm1031_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, adm1031_detect); -} - static struct attribute *adm1031_attributes[] = { &sensor_dev_attr_fan1_input.dev_attr.attr, &sensor_dev_attr_fan1_div.dev_attr.attr, @@ -770,27 +775,15 @@ static const struct attribute_group adm1031_group_opt = { .attrs = adm1031_attributes_opt, }; -/* This function is called by i2c_probe */ -static int adm1031_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int adm1031_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - struct i2c_client *client; - struct adm1031_data *data; - int err = 0; + struct i2c_adapter *adapter = client->adapter; const char *name = ""; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct adm1031_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &adm1031_driver; + return -ENODEV; if (kind < 0) { int id, co; @@ -798,7 +791,7 @@ static int adm1031_detect(struct i2c_adapter *adapter, int address, int kind) co = i2c_smbus_read_byte_data(client, 0x3e); if (!((id == 0x31 || id == 0x30) && co == 0x41)) - goto exit_free; + return -ENODEV; kind = (id == 0x30) ? adm1030 : adm1031; } @@ -809,28 +802,43 @@ static int adm1031_detect(struct i2c_adapter *adapter, int address, int kind) * auto fan control helper table. */ if (kind == adm1030) { name = "adm1030"; - data->chan_select_table = &auto_channel_select_table_adm1030; } else if (kind == adm1031) { name = "adm1031"; - data->chan_select_table = &auto_channel_select_table_adm1031; } - data->chip_type = kind; + strlcpy(info->type, name, I2C_NAME_SIZE); - strlcpy(client->name, name, I2C_NAME_SIZE); + return 0; +} + +static int adm1031_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct adm1031_data *data; + int err; + + data = kzalloc(sizeof(struct adm1031_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + data->chip_type = id->driver_data; mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_free; + if (data->chip_type == adm1030) + data->chan_select_table = &auto_channel_select_table_adm1030; + else + data->chan_select_table = &auto_channel_select_table_adm1031; /* Initialize the ADM1031 chip */ adm1031_init_client(client); /* Register sysfs hooks */ if ((err = sysfs_create_group(&client->dev.kobj, &adm1031_group))) - goto exit_detach; + goto exit_free; - if (kind == adm1031) { + if (data->chip_type == adm1031) { if ((err = sysfs_create_group(&client->dev.kobj, &adm1031_group_opt))) goto exit_remove; @@ -847,25 +855,19 @@ static int adm1031_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove: sysfs_remove_group(&client->dev.kobj, &adm1031_group); sysfs_remove_group(&client->dev.kobj, &adm1031_group_opt); -exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: return err; } -static int adm1031_detach_client(struct i2c_client *client) +static int adm1031_remove(struct i2c_client *client) { struct adm1031_data *data = i2c_get_clientdata(client); - int ret; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &adm1031_group); sysfs_remove_group(&client->dev.kobj, &adm1031_group_opt); - if ((ret = i2c_detach_client(client)) != 0) { - return ret; - } kfree(data); return 0; } diff --git a/drivers/hwmon/adm9240.c b/drivers/hwmon/adm9240.c index 149ef25252e..2444b15f2e9 100644 --- a/drivers/hwmon/adm9240.c +++ b/drivers/hwmon/adm9240.c @@ -130,25 +130,37 @@ static inline unsigned int AOUT_FROM_REG(u8 reg) return SCALE(reg, 1250, 255); } -static int adm9240_attach_adapter(struct i2c_adapter *adapter); -static int adm9240_detect(struct i2c_adapter *adapter, int address, int kind); +static int adm9240_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int adm9240_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); static void adm9240_init_client(struct i2c_client *client); -static int adm9240_detach_client(struct i2c_client *client); +static int adm9240_remove(struct i2c_client *client); static struct adm9240_data *adm9240_update_device(struct device *dev); /* driver data */ +static const struct i2c_device_id adm9240_id[] = { + { "adm9240", adm9240 }, + { "ds1780", ds1780 }, + { "lm81", lm81 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, adm9240_id); + static struct i2c_driver adm9240_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "adm9240", }, - .attach_adapter = adm9240_attach_adapter, - .detach_client = adm9240_detach_client, + .probe = adm9240_probe, + .remove = adm9240_remove, + .id_table = adm9240_id, + .detect = adm9240_detect, + .address_data = &addr_data, }; /* per client data */ struct adm9240_data { - enum chips type; - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; @@ -532,28 +544,17 @@ static const struct attribute_group adm9240_group = { /*** sensor chip detect and driver install ***/ -static int adm9240_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int adm9240_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info) { - struct i2c_client *new_client; - struct adm9240_data *data; - int err = 0; + struct i2c_adapter *adapter = new_client->adapter; const char *name = ""; + int address = new_client->addr; u8 man_id, die_rev; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(*data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - new_client = &data->client; - i2c_set_clientdata(new_client, data); - new_client->addr = address; - new_client->adapter = adapter; - new_client->driver = &adm9240_driver; - new_client->flags = 0; + return -ENODEV; if (kind == 0) { kind = adm9240; @@ -566,7 +567,7 @@ static int adm9240_detect(struct i2c_adapter *adapter, int address, int kind) != address) { dev_err(&adapter->dev, "detect fail: address match, " "0x%02x\n", address); - goto exit_free; + return -ENODEV; } /* check known chip manufacturer */ @@ -581,7 +582,7 @@ static int adm9240_detect(struct i2c_adapter *adapter, int address, int kind) } else { dev_err(&adapter->dev, "detect fail: unknown manuf, " "0x%02x\n", man_id); - goto exit_free; + return -ENODEV; } /* successful detect, print chip info */ @@ -600,20 +601,31 @@ static int adm9240_detect(struct i2c_adapter *adapter, int address, int kind) } else if (kind == lm81) { name = "lm81"; } + strlcpy(info->type, name, I2C_NAME_SIZE); - /* fill in the remaining client fields and attach */ - strlcpy(new_client->name, name, I2C_NAME_SIZE); - data->type = kind; - mutex_init(&data->update_lock); + return 0; +} - if ((err = i2c_attach_client(new_client))) - goto exit_free; +static int adm9240_probe(struct i2c_client *new_client, + const struct i2c_device_id *id) +{ + struct adm9240_data *data; + int err; + + data = kzalloc(sizeof(*data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(new_client, data); + mutex_init(&data->update_lock); adm9240_init_client(new_client); /* populate sysfs filesystem */ if ((err = sysfs_create_group(&new_client->dev.kobj, &adm9240_group))) - goto exit_detach; + goto exit_free; data->hwmon_dev = hwmon_device_register(&new_client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -625,32 +637,19 @@ static int adm9240_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove: sysfs_remove_group(&new_client->dev.kobj, &adm9240_group); -exit_detach: - i2c_detach_client(new_client); exit_free: kfree(data); exit: return err; } -static int adm9240_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, adm9240_detect); -} - -static int adm9240_detach_client(struct i2c_client *client) +static int adm9240_remove(struct i2c_client *client) { struct adm9240_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &adm9240_group); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } diff --git a/drivers/hwmon/ads7828.c b/drivers/hwmon/ads7828.c index 5c8b6e0ff47..5c39b4af1b2 100644 --- a/drivers/hwmon/ads7828.c +++ b/drivers/hwmon/ads7828.c @@ -64,7 +64,6 @@ static unsigned int ads7828_lsb_resol; /* resolution of the ADC sample lsb */ /* Each client has this additional data */ struct ads7828_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; /* mutex protect updates */ char valid; /* !=0 if following fields are valid */ @@ -73,7 +72,10 @@ struct ads7828_data { }; /* Function declaration - necessary due to function dependencies */ -static int ads7828_detect(struct i2c_adapter *adapter, int address, int kind); +static int ads7828_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int ads7828_probe(struct i2c_client *client, + const struct i2c_device_id *id); /* The ADS7828 returns the 12-bit sample in two bytes, these are read as a word then byte-swapped */ @@ -156,58 +158,43 @@ static const struct attribute_group ads7828_group = { .attrs = ads7828_attributes, }; -static int ads7828_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, ads7828_detect); -} - -static int ads7828_detach_client(struct i2c_client *client) +static int ads7828_remove(struct i2c_client *client) { struct ads7828_data *data = i2c_get_clientdata(client); hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &ads7828_group); - i2c_detach_client(client); kfree(i2c_get_clientdata(client)); return 0; } +static const struct i2c_device_id ads7828_id[] = { + { "ads7828", ads7828 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, ads7828_id); + /* This is the driver that will be inserted */ static struct i2c_driver ads7828_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "ads7828", }, - .attach_adapter = ads7828_attach_adapter, - .detach_client = ads7828_detach_client, + .probe = ads7828_probe, + .remove = ads7828_remove, + .id_table = ads7828_id, + .detect = ads7828_detect, + .address_data = &addr_data, }; -/* This function is called by i2c_probe */ -static int ads7828_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int ads7828_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - struct i2c_client *client; - struct ads7828_data *data; - int err = 0; - const char *name = ""; + struct i2c_adapter *adapter = client->adapter; /* Check we have a valid client */ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_WORD_DATA)) - goto exit; - - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access ads7828_read_value. */ - data = kzalloc(sizeof(struct ads7828_data), GFP_KERNEL); - if (!data) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &ads7828_driver; + return -ENODEV; /* Now, we do the remaining detection. There is no identification dedicated register so attempt to sanity check using knowledge of @@ -225,32 +212,34 @@ static int ads7828_detect(struct i2c_adapter *adapter, int address, int kind) printk(KERN_DEBUG "%s : Doesn't look like an ads7828 device\n", __func__); - goto exit_free; + return -ENODEV; } } } + strlcpy(info->type, "ads7828", I2C_NAME_SIZE); - /* Determine the chip type - only one kind supported! */ - if (kind <= 0) - kind = ads7828; + return 0; +} - if (kind == ads7828) - name = "ads7828"; +static int ads7828_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct ads7828_data *data; + int err; - /* Fill in the remaining client fields, put it into the global list */ - strlcpy(client->name, name, I2C_NAME_SIZE); + data = kzalloc(sizeof(struct ads7828_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + i2c_set_clientdata(client, data); mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - err = i2c_attach_client(client); - if (err) - goto exit_free; - /* Register sysfs hooks */ err = sysfs_create_group(&client->dev.kobj, &ads7828_group); if (err) - goto exit_detach; + goto exit_free; data->hwmon_dev = hwmon_device_register(&client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -262,8 +251,6 @@ static int ads7828_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove: sysfs_remove_group(&client->dev.kobj, &ads7828_group); -exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: diff --git a/drivers/hwmon/adt7470.c b/drivers/hwmon/adt7470.c index 6b5325f33a2..d368d8f845e 100644 --- a/drivers/hwmon/adt7470.c +++ b/drivers/hwmon/adt7470.c @@ -138,7 +138,6 @@ I2C_CLIENT_INSMOD_1(adt7470); #define FAN_DATA_VALID(x) ((x) && (x) != FAN_PERIOD_INVALID) struct adt7470_data { - struct i2c_client client; struct device *hwmon_dev; struct attribute_group attrs; struct mutex lock; @@ -164,16 +163,28 @@ struct adt7470_data { u8 pwm_auto_temp[ADT7470_PWM_COUNT]; }; -static int adt7470_attach_adapter(struct i2c_adapter *adapter); -static int adt7470_detect(struct i2c_adapter *adapter, int address, int kind); -static int adt7470_detach_client(struct i2c_client *client); +static int adt7470_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int adt7470_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int adt7470_remove(struct i2c_client *client); + +static const struct i2c_device_id adt7470_id[] = { + { "adt7470", adt7470 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, adt7470_id); static struct i2c_driver adt7470_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "adt7470", }, - .attach_adapter = adt7470_attach_adapter, - .detach_client = adt7470_detach_client, + .probe = adt7470_probe, + .remove = adt7470_remove, + .id_table = adt7470_id, + .detect = adt7470_detect, + .address_data = &addr_data, }; /* @@ -1004,64 +1015,52 @@ static struct attribute *adt7470_attr[] = NULL }; -static int adt7470_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, adt7470_detect); -} - -static int adt7470_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int adt7470_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - struct i2c_client *client; - struct adt7470_data *data; - int err = 0; + struct i2c_adapter *adapter = client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct adt7470_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - client->addr = address; - client->adapter = adapter; - client->driver = &adt7470_driver; - - i2c_set_clientdata(client, data); - - mutex_init(&data->lock); + return -ENODEV; if (kind <= 0) { int vendor, device, revision; vendor = i2c_smbus_read_byte_data(client, ADT7470_REG_VENDOR); - if (vendor != ADT7470_VENDOR) { - err = -ENODEV; - goto exit_free; - } + if (vendor != ADT7470_VENDOR) + return -ENODEV; device = i2c_smbus_read_byte_data(client, ADT7470_REG_DEVICE); - if (device != ADT7470_DEVICE) { - err = -ENODEV; - goto exit_free; - } + if (device != ADT7470_DEVICE) + return -ENODEV; revision = i2c_smbus_read_byte_data(client, ADT7470_REG_REVISION); - if (revision != ADT7470_REVISION) { - err = -ENODEV; - goto exit_free; - } + if (revision != ADT7470_REVISION) + return -ENODEV; } else dev_dbg(&adapter->dev, "detection forced\n"); - strlcpy(client->name, "adt7470", I2C_NAME_SIZE); + strlcpy(info->type, "adt7470", I2C_NAME_SIZE); - if ((err = i2c_attach_client(client))) - goto exit_free; + return 0; +} + +static int adt7470_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct adt7470_data *data; + int err; + + data = kzalloc(sizeof(struct adt7470_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + mutex_init(&data->lock); dev_info(&client->dev, "%s chip found\n", client->name); @@ -1071,7 +1070,7 @@ static int adt7470_detect(struct i2c_adapter *adapter, int address, int kind) /* Register sysfs hooks */ data->attrs.attrs = adt7470_attr; if ((err = sysfs_create_group(&client->dev.kobj, &data->attrs))) - goto exit_detach; + goto exit_free; data->hwmon_dev = hwmon_device_register(&client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -1083,21 +1082,18 @@ static int adt7470_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove: sysfs_remove_group(&client->dev.kobj, &data->attrs); -exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: return err; } -static int adt7470_detach_client(struct i2c_client *client) +static int adt7470_remove(struct i2c_client *client) { struct adt7470_data *data = i2c_get_clientdata(client); hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &data->attrs); - i2c_detach_client(client); kfree(data); return 0; } diff --git a/drivers/hwmon/adt7473.c b/drivers/hwmon/adt7473.c index 93dbf5e7ff8..ce4a7cb5a11 100644 --- a/drivers/hwmon/adt7473.c +++ b/drivers/hwmon/adt7473.c @@ -143,7 +143,6 @@ I2C_CLIENT_INSMOD_1(adt7473); #define FAN_DATA_VALID(x) ((x) && (x) != FAN_PERIOD_INVALID) struct adt7473_data { - struct i2c_client client; struct device *hwmon_dev; struct attribute_group attrs; struct mutex lock; @@ -178,16 +177,28 @@ struct adt7473_data { u8 max_duty_at_overheat; }; -static int adt7473_attach_adapter(struct i2c_adapter *adapter); -static int adt7473_detect(struct i2c_adapter *adapter, int address, int kind); -static int adt7473_detach_client(struct i2c_client *client); +static int adt7473_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int adt7473_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int adt7473_remove(struct i2c_client *client); + +static const struct i2c_device_id adt7473_id[] = { + { "adt7473", adt7473 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, adt7473_id); static struct i2c_driver adt7473_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "adt7473", }, - .attach_adapter = adt7473_attach_adapter, - .detach_client = adt7473_detach_client, + .probe = adt7473_probe, + .remove = adt7473_remove, + .id_table = adt7473_id, + .detect = adt7473_detect, + .address_data = &addr_data, }; /* @@ -1042,66 +1053,52 @@ static struct attribute *adt7473_attr[] = NULL }; -static int adt7473_attach_adapter(struct i2c_adapter *adapter) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int adt7473_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, adt7473_detect); -} - -static int adt7473_detect(struct i2c_adapter *adapter, int address, int kind) -{ - struct i2c_client *client; - struct adt7473_data *data; - int err = 0; + struct i2c_adapter *adapter = client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - data = kzalloc(sizeof(struct adt7473_data), GFP_KERNEL); - if (!data) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - client->addr = address; - client->adapter = adapter; - client->driver = &adt7473_driver; - - i2c_set_clientdata(client, data); - - mutex_init(&data->lock); + return -ENODEV; if (kind <= 0) { int vendor, device, revision; vendor = i2c_smbus_read_byte_data(client, ADT7473_REG_VENDOR); - if (vendor != ADT7473_VENDOR) { - err = -ENODEV; - goto exit_free; - } + if (vendor != ADT7473_VENDOR) + return -ENODEV; device = i2c_smbus_read_byte_data(client, ADT7473_REG_DEVICE); - if (device != ADT7473_DEVICE) { - err = -ENODEV; - goto exit_free; - } + if (device != ADT7473_DEVICE) + return -ENODEV; revision = i2c_smbus_read_byte_data(client, ADT7473_REG_REVISION); - if (revision != ADT7473_REV_68 && revision != ADT7473_REV_69) { - err = -ENODEV; - goto exit_free; - } + if (revision != ADT7473_REV_68 && revision != ADT7473_REV_69) + return -ENODEV; } else dev_dbg(&adapter->dev, "detection forced\n"); - strlcpy(client->name, "adt7473", I2C_NAME_SIZE); + strlcpy(info->type, "adt7473", I2C_NAME_SIZE); - err = i2c_attach_client(client); - if (err) - goto exit_free; + return 0; +} + +static int adt7473_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct adt7473_data *data; + int err; + + data = kzalloc(sizeof(struct adt7473_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + mutex_init(&data->lock); dev_info(&client->dev, "%s chip found\n", client->name); @@ -1112,7 +1109,7 @@ static int adt7473_detect(struct i2c_adapter *adapter, int address, int kind) data->attrs.attrs = adt7473_attr; err = sysfs_create_group(&client->dev.kobj, &data->attrs); if (err) - goto exit_detach; + goto exit_free; data->hwmon_dev = hwmon_device_register(&client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -1124,21 +1121,18 @@ static int adt7473_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove: sysfs_remove_group(&client->dev.kobj, &data->attrs); -exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: return err; } -static int adt7473_detach_client(struct i2c_client *client) +static int adt7473_remove(struct i2c_client *client) { struct adt7473_data *data = i2c_get_clientdata(client); hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &data->attrs); - i2c_detach_client(client); kfree(data); return 0; } diff --git a/drivers/hwmon/asb100.c b/drivers/hwmon/asb100.c index fe2eea4d799..8a45a2e6ba8 100644 --- a/drivers/hwmon/asb100.c +++ b/drivers/hwmon/asb100.c @@ -176,10 +176,8 @@ static u8 DIV_TO_REG(long val) data is pointed to by client->data. The structure itself is dynamically allocated, at the same time the client itself is allocated. */ struct asb100_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex lock; - enum chips type; struct mutex update_lock; unsigned long last_updated; /* In jiffies */ @@ -206,18 +204,30 @@ struct asb100_data { static int asb100_read_value(struct i2c_client *client, u16 reg); static void asb100_write_value(struct i2c_client *client, u16 reg, u16 val); -static int asb100_attach_adapter(struct i2c_adapter *adapter); -static int asb100_detect(struct i2c_adapter *adapter, int address, int kind); -static int asb100_detach_client(struct i2c_client *client); +static int asb100_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int asb100_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int asb100_remove(struct i2c_client *client); static struct asb100_data *asb100_update_device(struct device *dev); static void asb100_init_client(struct i2c_client *client); +static const struct i2c_device_id asb100_id[] = { + { "asb100", asb100 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, asb100_id); + static struct i2c_driver asb100_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "asb100", }, - .attach_adapter = asb100_attach_adapter, - .detach_client = asb100_detach_client, + .probe = asb100_probe, + .remove = asb100_remove, + .id_table = asb100_id, + .detect = asb100_detect, + .address_data = &addr_data, }; /* 7 Voltages */ @@ -619,35 +629,13 @@ static const struct attribute_group asb100_group = { .attrs = asb100_attributes, }; -/* This function is called when: - asb100_driver is inserted (when this module is loaded), for each - available adapter - when a new adapter is inserted (and asb100_driver is still present) - */ -static int asb100_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, asb100_detect); -} - -static int asb100_detect_subclients(struct i2c_adapter *adapter, int address, - int kind, struct i2c_client *client) +static int asb100_detect_subclients(struct i2c_client *client) { int i, id, err; + int address = client->addr; + unsigned short sc_addr[2]; struct asb100_data *data = i2c_get_clientdata(client); - - data->lm75[0] = kzalloc(sizeof(struct i2c_client), GFP_KERNEL); - if (!(data->lm75[0])) { - err = -ENOMEM; - goto ERROR_SC_0; - } - - data->lm75[1] = kzalloc(sizeof(struct i2c_client), GFP_KERNEL); - if (!(data->lm75[1])) { - err = -ENOMEM; - goto ERROR_SC_1; - } + struct i2c_adapter *adapter = client->adapter; id = i2c_adapter_id(adapter); @@ -665,37 +653,34 @@ static int asb100_detect_subclients(struct i2c_adapter *adapter, int address, asb100_write_value(client, ASB100_REG_I2C_SUBADDR, (force_subclients[2] & 0x07) | ((force_subclients[3] & 0x07) << 4)); - data->lm75[0]->addr = force_subclients[2]; - data->lm75[1]->addr = force_subclients[3]; + sc_addr[0] = force_subclients[2]; + sc_addr[1] = force_subclients[3]; } else { int val = asb100_read_value(client, ASB100_REG_I2C_SUBADDR); - data->lm75[0]->addr = 0x48 + (val & 0x07); - data->lm75[1]->addr = 0x48 + ((val >> 4) & 0x07); + sc_addr[0] = 0x48 + (val & 0x07); + sc_addr[1] = 0x48 + ((val >> 4) & 0x07); } - if (data->lm75[0]->addr == data->lm75[1]->addr) { + if (sc_addr[0] == sc_addr[1]) { dev_err(&client->dev, "duplicate addresses 0x%x " - "for subclients\n", data->lm75[0]->addr); + "for subclients\n", sc_addr[0]); err = -ENODEV; goto ERROR_SC_2; } - for (i = 0; i <= 1; i++) { - i2c_set_clientdata(data->lm75[i], NULL); - data->lm75[i]->adapter = adapter; - data->lm75[i]->driver = &asb100_driver; - strlcpy(data->lm75[i]->name, "asb100 subclient", I2C_NAME_SIZE); - } - - if ((err = i2c_attach_client(data->lm75[0]))) { + data->lm75[0] = i2c_new_dummy(adapter, sc_addr[0]); + if (!data->lm75[0]) { dev_err(&client->dev, "subclient %d registration " - "at address 0x%x failed.\n", i, data->lm75[0]->addr); + "at address 0x%x failed.\n", 1, sc_addr[0]); + err = -ENOMEM; goto ERROR_SC_2; } - if ((err = i2c_attach_client(data->lm75[1]))) { + data->lm75[1] = i2c_new_dummy(adapter, sc_addr[1]); + if (!data->lm75[1]) { dev_err(&client->dev, "subclient %d registration " - "at address 0x%x failed.\n", i, data->lm75[1]->addr); + "at address 0x%x failed.\n", 2, sc_addr[1]); + err = -ENOMEM; goto ERROR_SC_3; } @@ -703,55 +688,31 @@ static int asb100_detect_subclients(struct i2c_adapter *adapter, int address, /* Undo inits in case of errors */ ERROR_SC_3: - i2c_detach_client(data->lm75[0]); + i2c_unregister_device(data->lm75[0]); ERROR_SC_2: - kfree(data->lm75[1]); -ERROR_SC_1: - kfree(data->lm75[0]); -ERROR_SC_0: return err; } -static int asb100_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int asb100_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - int err; - struct i2c_client *client; - struct asb100_data *data; + struct i2c_adapter *adapter = client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { pr_debug("asb100.o: detect failed, " "smbus byte data not supported!\n"); - err = -ENODEV; - goto ERROR0; + return -ENODEV; } - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access asb100_{read,write}_value. */ - - if (!(data = kzalloc(sizeof(struct asb100_data), GFP_KERNEL))) { - pr_debug("asb100.o: detect failed, kzalloc failed!\n"); - err = -ENOMEM; - goto ERROR0; - } - - client = &data->client; - mutex_init(&data->lock); - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &asb100_driver; - - /* Now, we do the remaining detection. */ - /* The chip may be stuck in some other bank than bank 0. This may make reading other information impossible. Specify a force=... or force_*=... parameter, and the chip will be reset to the right bank. */ if (kind < 0) { - int val1 = asb100_read_value(client, ASB100_REG_BANK); - int val2 = asb100_read_value(client, ASB100_REG_CHIPMAN); + int val1 = i2c_smbus_read_byte_data(client, ASB100_REG_BANK); + int val2 = i2c_smbus_read_byte_data(client, ASB100_REG_CHIPMAN); /* If we're in bank 0 */ if ((!(val1 & 0x07)) && @@ -761,48 +722,60 @@ static int asb100_detect(struct i2c_adapter *adapter, int address, int kind) ((val1 & 0x80) && (val2 != 0x06)))) { pr_debug("asb100.o: detect failed, " "bad chip id 0x%02x!\n", val2); - err = -ENODEV; - goto ERROR1; + return -ENODEV; } } /* kind < 0 */ /* We have either had a force parameter, or we have already detected Winbond. Put it now into bank 0 and Vendor ID High Byte */ - asb100_write_value(client, ASB100_REG_BANK, - (asb100_read_value(client, ASB100_REG_BANK) & 0x78) | 0x80); + i2c_smbus_write_byte_data(client, ASB100_REG_BANK, + (i2c_smbus_read_byte_data(client, ASB100_REG_BANK) & 0x78) + | 0x80); /* Determine the chip type. */ if (kind <= 0) { - int val1 = asb100_read_value(client, ASB100_REG_WCHIPID); - int val2 = asb100_read_value(client, ASB100_REG_CHIPMAN); + int val1 = i2c_smbus_read_byte_data(client, ASB100_REG_WCHIPID); + int val2 = i2c_smbus_read_byte_data(client, ASB100_REG_CHIPMAN); if ((val1 == 0x31) && (val2 == 0x06)) kind = asb100; else { if (kind == 0) - dev_warn(&client->dev, "ignoring " + dev_warn(&adapter->dev, "ignoring " "'force' parameter for unknown chip " "at adapter %d, address 0x%02x.\n", - i2c_adapter_id(adapter), address); - err = -ENODEV; - goto ERROR1; + i2c_adapter_id(adapter), client->addr); + return -ENODEV; } } - /* Fill in remaining client fields and put it into the global list */ - strlcpy(client->name, "asb100", I2C_NAME_SIZE); - data->type = kind; - mutex_init(&data->update_lock); + strlcpy(info->type, "asb100", I2C_NAME_SIZE); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto ERROR1; + return 0; +} + +static int asb100_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + int err; + struct asb100_data *data; + + data = kzalloc(sizeof(struct asb100_data), GFP_KERNEL); + if (!data) { + pr_debug("asb100.o: probe failed, kzalloc failed!\n"); + err = -ENOMEM; + goto ERROR0; + } + + i2c_set_clientdata(client, data); + mutex_init(&data->lock); + mutex_init(&data->update_lock); /* Attach secondary lm75 clients */ - if ((err = asb100_detect_subclients(adapter, address, kind, - client))) - goto ERROR2; + err = asb100_detect_subclients(client); + if (err) + goto ERROR1; /* Initialize the chip */ asb100_init_client(client); @@ -827,39 +800,25 @@ static int asb100_detect(struct i2c_adapter *adapter, int address, int kind) ERROR4: sysfs_remove_group(&client->dev.kobj, &asb100_group); ERROR3: - i2c_detach_client(data->lm75[1]); - i2c_detach_client(data->lm75[0]); - kfree(data->lm75[1]); - kfree(data->lm75[0]); -ERROR2: - i2c_detach_client(client); + i2c_unregister_device(data->lm75[1]); + i2c_unregister_device(data->lm75[0]); ERROR1: kfree(data); ERROR0: return err; } -static int asb100_detach_client(struct i2c_client *client) +static int asb100_remove(struct i2c_client *client) { struct asb100_data *data = i2c_get_clientdata(client); - int err; - - /* main client */ - if (data) { - hwmon_device_unregister(data->hwmon_dev); - sysfs_remove_group(&client->dev.kobj, &asb100_group); - } - if ((err = i2c_detach_client(client))) - return err; + hwmon_device_unregister(data->hwmon_dev); + sysfs_remove_group(&client->dev.kobj, &asb100_group); - /* main client */ - if (data) - kfree(data); + i2c_unregister_device(data->lm75[1]); + i2c_unregister_device(data->lm75[0]); - /* subclient */ - else - kfree(client); + kfree(data); return 0; } diff --git a/drivers/hwmon/atxp1.c b/drivers/hwmon/atxp1.c index 01c17e387f0..d191118ba0c 100644 --- a/drivers/hwmon/atxp1.c +++ b/drivers/hwmon/atxp1.c @@ -46,21 +46,32 @@ static const unsigned short normal_i2c[] = { 0x37, 0x4e, I2C_CLIENT_END }; I2C_CLIENT_INSMOD_1(atxp1); -static int atxp1_attach_adapter(struct i2c_adapter * adapter); -static int atxp1_detach_client(struct i2c_client * client); +static int atxp1_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int atxp1_remove(struct i2c_client *client); static struct atxp1_data * atxp1_update_device(struct device *dev); -static int atxp1_detect(struct i2c_adapter *adapter, int address, int kind); +static int atxp1_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); + +static const struct i2c_device_id atxp1_id[] = { + { "atxp1", atxp1 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, atxp1_id); static struct i2c_driver atxp1_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "atxp1", }, - .attach_adapter = atxp1_attach_adapter, - .detach_client = atxp1_detach_client, + .probe = atxp1_probe, + .remove = atxp1_remove, + .id_table = atxp1_id, + .detect = atxp1_detect, + .address_data = &addr_data, }; struct atxp1_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; unsigned long last_updated; @@ -263,35 +274,16 @@ static const struct attribute_group atxp1_group = { }; -static int atxp1_attach_adapter(struct i2c_adapter *adapter) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int atxp1_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info) { - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, &atxp1_detect); -}; + struct i2c_adapter *adapter = new_client->adapter; -static int atxp1_detect(struct i2c_adapter *adapter, int address, int kind) -{ - struct i2c_client * new_client; - struct atxp1_data * data; - int err = 0; u8 temp; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct atxp1_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - new_client = &data->client; - i2c_set_clientdata(new_client, data); - - new_client->addr = address; - new_client->adapter = adapter; - new_client->driver = &atxp1_driver; - new_client->flags = 0; + return -ENODEV; /* Detect ATXP1, checking if vendor ID registers are all zero */ if (!((i2c_smbus_read_byte_data(new_client, 0x3e) == 0) && @@ -305,35 +297,46 @@ static int atxp1_detect(struct i2c_adapter *adapter, int address, int kind) if (!((i2c_smbus_read_byte_data(new_client, 0x10) == temp) && (i2c_smbus_read_byte_data(new_client, 0x11) == temp) )) - goto exit_free; + return -ENODEV; } /* Get VRM */ - data->vrm = vid_which_vrm(); + temp = vid_which_vrm(); - if ((data->vrm != 90) && (data->vrm != 91)) { - dev_err(&new_client->dev, "Not supporting VRM %d.%d\n", - data->vrm / 10, data->vrm % 10); - goto exit_free; + if ((temp != 90) && (temp != 91)) { + dev_err(&adapter->dev, "atxp1: Not supporting VRM %d.%d\n", + temp / 10, temp % 10); + return -ENODEV; } - strncpy(new_client->name, "atxp1", I2C_NAME_SIZE); - - data->valid = 0; + strlcpy(info->type, "atxp1", I2C_NAME_SIZE); - mutex_init(&data->update_lock); + return 0; +} - err = i2c_attach_client(new_client); +static int atxp1_probe(struct i2c_client *new_client, + const struct i2c_device_id *id) +{ + struct atxp1_data *data; + int err; - if (err) - { - dev_err(&new_client->dev, "Attach client error.\n"); - goto exit_free; + data = kzalloc(sizeof(struct atxp1_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; } + /* Get VRM */ + data->vrm = vid_which_vrm(); + + i2c_set_clientdata(new_client, data); + data->valid = 0; + + mutex_init(&data->update_lock); + /* Register sysfs hooks */ if ((err = sysfs_create_group(&new_client->dev.kobj, &atxp1_group))) - goto exit_detach; + goto exit_free; data->hwmon_dev = hwmon_device_register(&new_client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -348,30 +351,22 @@ static int atxp1_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove_files: sysfs_remove_group(&new_client->dev.kobj, &atxp1_group); -exit_detach: - i2c_detach_client(new_client); exit_free: kfree(data); exit: return err; }; -static int atxp1_detach_client(struct i2c_client * client) +static int atxp1_remove(struct i2c_client *client) { struct atxp1_data * data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &atxp1_group); - err = i2c_detach_client(client); - - if (err) - dev_err(&client->dev, "Failed to detach client.\n"); - else - kfree(data); + kfree(data); - return err; + return 0; }; static int __init atxp1_init(void) diff --git a/drivers/hwmon/ds1621.c b/drivers/hwmon/ds1621.c index 5f300ffed65..7415381601c 100644 --- a/drivers/hwmon/ds1621.c +++ b/drivers/hwmon/ds1621.c @@ -72,7 +72,6 @@ static const u8 DS1621_REG_TEMP[3] = { /* Each client has this additional data */ struct ds1621_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* !=0 if following fields are valid */ @@ -82,20 +81,32 @@ struct ds1621_data { u8 conf; /* Register encoding, combined */ }; -static int ds1621_attach_adapter(struct i2c_adapter *adapter); -static int ds1621_detect(struct i2c_adapter *adapter, int address, - int kind); +static int ds1621_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int ds1621_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); static void ds1621_init_client(struct i2c_client *client); -static int ds1621_detach_client(struct i2c_client *client); +static int ds1621_remove(struct i2c_client *client); static struct ds1621_data *ds1621_update_client(struct device *dev); +static const struct i2c_device_id ds1621_id[] = { + { "ds1621", ds1621 }, + { "ds1625", ds1621 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, ds1621_id); + /* This is the driver that will be inserted */ static struct i2c_driver ds1621_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "ds1621", }, - .attach_adapter = ds1621_attach_adapter, - .detach_client = ds1621_detach_client, + .probe = ds1621_probe, + .remove = ds1621_remove, + .id_table = ds1621_id, + .detect = ds1621_detect, + .address_data = &addr_data, }; /* All registers are word-sized, except for the configuration register. @@ -199,40 +210,18 @@ static const struct attribute_group ds1621_group = { }; -static int ds1621_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, ds1621_detect); -} - -/* This function is called by i2c_probe */ -static int ds1621_detect(struct i2c_adapter *adapter, int address, - int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int ds1621_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { + struct i2c_adapter *adapter = client->adapter; int conf, temp; - struct i2c_client *client; - struct ds1621_data *data; - int i, err = 0; + int i; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA | I2C_FUNC_SMBUS_WRITE_BYTE)) - goto exit; - - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access ds1621_{read,write}_value. */ - if (!(data = kzalloc(sizeof(struct ds1621_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &ds1621_driver; + return -ENODEV; /* Now, we do the remaining detection. It is lousy. */ if (kind < 0) { @@ -241,29 +230,41 @@ static int ds1621_detect(struct i2c_adapter *adapter, int address, improbable in our case. */ conf = ds1621_read_value(client, DS1621_REG_CONF); if (conf & DS1621_REG_CONFIG_NVB) - goto exit_free; + return -ENODEV; /* The 7 lowest bits of a temperature should always be 0. */ - for (i = 0; i < ARRAY_SIZE(data->temp); i++) { + for (i = 0; i < ARRAY_SIZE(DS1621_REG_TEMP); i++) { temp = ds1621_read_value(client, DS1621_REG_TEMP[i]); if (temp & 0x007f) - goto exit_free; + return -ENODEV; } } - /* Fill in remaining client fields and put it into the global list */ - strlcpy(client->name, "ds1621", I2C_NAME_SIZE); - mutex_init(&data->update_lock); + strlcpy(info->type, "ds1621", I2C_NAME_SIZE); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_free; + return 0; +} + +static int ds1621_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct ds1621_data *data; + int err; + + data = kzalloc(sizeof(struct ds1621_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); /* Initialize the DS1621 chip */ ds1621_init_client(client); /* Register sysfs hooks */ if ((err = sysfs_create_group(&client->dev.kobj, &ds1621_group))) - goto exit_detach; + goto exit_free; data->hwmon_dev = hwmon_device_register(&client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -275,25 +276,19 @@ static int ds1621_detect(struct i2c_adapter *adapter, int address, exit_remove_files: sysfs_remove_group(&client->dev.kobj, &ds1621_group); - exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: return err; } -static int ds1621_detach_client(struct i2c_client *client) +static int ds1621_remove(struct i2c_client *client) { struct ds1621_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &ds1621_group); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; diff --git a/drivers/hwmon/f75375s.c b/drivers/hwmon/f75375s.c index dc1f30e432e..1692de36996 100644 --- a/drivers/hwmon/f75375s.c +++ b/drivers/hwmon/f75375s.c @@ -87,7 +87,6 @@ I2C_CLIENT_INSMOD_2(f75373, f75375); struct f75375_data { unsigned short addr; - struct i2c_client *client; struct device *hwmon_dev; const char *name; @@ -114,21 +113,12 @@ struct f75375_data { s8 temp_max_hyst[2]; }; -static int f75375_attach_adapter(struct i2c_adapter *adapter); -static int f75375_detect(struct i2c_adapter *adapter, int address, int kind); -static int f75375_detach_client(struct i2c_client *client); +static int f75375_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); static int f75375_probe(struct i2c_client *client, const struct i2c_device_id *id); static int f75375_remove(struct i2c_client *client); -static struct i2c_driver f75375_legacy_driver = { - .driver = { - .name = "f75375_legacy", - }, - .attach_adapter = f75375_attach_adapter, - .detach_client = f75375_detach_client, -}; - static const struct i2c_device_id f75375_id[] = { { "f75373", f75373 }, { "f75375", f75375 }, @@ -137,12 +127,15 @@ static const struct i2c_device_id f75375_id[] = { MODULE_DEVICE_TABLE(i2c, f75375_id); static struct i2c_driver f75375_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "f75375", }, .probe = f75375_probe, .remove = f75375_remove, .id_table = f75375_id, + .detect = f75375_detect, + .address_data = &addr_data, }; static inline int f75375_read8(struct i2c_client *client, u8 reg) @@ -607,22 +600,6 @@ static const struct attribute_group f75375_group = { .attrs = f75375_attributes, }; -static int f75375_detach_client(struct i2c_client *client) -{ - int err; - - f75375_remove(client); - err = i2c_detach_client(client); - if (err) { - dev_err(&client->dev, - "Client deregistration failed, " - "client not detached.\n"); - return err; - } - kfree(client); - return 0; -} - static void f75375_init(struct i2c_client *client, struct f75375_data *data, struct f75375s_platform_data *f75375s_pdata) { @@ -651,7 +628,6 @@ static int f75375_probe(struct i2c_client *client, return -ENOMEM; i2c_set_clientdata(client, data); - data->client = client; mutex_init(&data->update_lock); data->kind = id->driver_data; @@ -700,29 +676,13 @@ static int f75375_remove(struct i2c_client *client) return 0; } -static int f75375_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, f75375_detect); -} - -/* This function is called by i2c_probe */ -static int f75375_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int f75375_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - struct i2c_client *client; + struct i2c_adapter *adapter = client->adapter; u8 version = 0; - int err = 0; const char *name = ""; - struct i2c_device_id id; - - if (!(client = kzalloc(sizeof(*client), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - client->addr = address; - client->adapter = adapter; - client->driver = &f75375_legacy_driver; if (kind < 0) { u16 vendid = f75375_read16(client, F75375_REG_VENDOR); @@ -736,7 +696,7 @@ static int f75375_detect(struct i2c_adapter *adapter, int address, int kind) dev_err(&adapter->dev, "failed,%02X,%02X,%02X\n", chipid, version, vendid); - goto exit_free; + return -ENODEV; } } @@ -746,43 +706,18 @@ static int f75375_detect(struct i2c_adapter *adapter, int address, int kind) name = "f75373"; } dev_info(&adapter->dev, "found %s version: %02X\n", name, version); - strlcpy(client->name, name, I2C_NAME_SIZE); - - if ((err = i2c_attach_client(client))) - goto exit_free; - - strlcpy(id.name, name, I2C_NAME_SIZE); - id.driver_data = kind; - if ((err = f75375_probe(client, &id)) < 0) - goto exit_detach; + strlcpy(info->type, name, I2C_NAME_SIZE); return 0; - -exit_detach: - i2c_detach_client(client); -exit_free: - kfree(client); -exit: - return err; } static int __init sensors_f75375_init(void) { - int status; - status = i2c_add_driver(&f75375_driver); - if (status) - return status; - - status = i2c_add_driver(&f75375_legacy_driver); - if (status) - i2c_del_driver(&f75375_driver); - - return status; + return i2c_add_driver(&f75375_driver); } static void __exit sensors_f75375_exit(void) { - i2c_del_driver(&f75375_legacy_driver); i2c_del_driver(&f75375_driver); } diff --git a/drivers/hwmon/fscher.c b/drivers/hwmon/fscher.c index ed26b66e083..12c70e402cb 100644 --- a/drivers/hwmon/fscher.c +++ b/drivers/hwmon/fscher.c @@ -106,9 +106,11 @@ I2C_CLIENT_INSMOD_1(fscher); * Functions declaration */ -static int fscher_attach_adapter(struct i2c_adapter *adapter); -static int fscher_detect(struct i2c_adapter *adapter, int address, int kind); -static int fscher_detach_client(struct i2c_client *client); +static int fscher_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int fscher_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int fscher_remove(struct i2c_client *client); static struct fscher_data *fscher_update_device(struct device *dev); static void fscher_init_client(struct i2c_client *client); @@ -119,12 +121,21 @@ static int fscher_write_value(struct i2c_client *client, u8 reg, u8 value); * Driver data (common to all clients) */ +static const struct i2c_device_id fscher_id[] = { + { "fscher", fscher }, + { } +}; + static struct i2c_driver fscher_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "fscher", }, - .attach_adapter = fscher_attach_adapter, - .detach_client = fscher_detach_client, + .probe = fscher_probe, + .remove = fscher_remove, + .id_table = fscher_id, + .detect = fscher_detect, + .address_data = &addr_data, }; /* @@ -132,7 +143,6 @@ static struct i2c_driver fscher_driver = { */ struct fscher_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* zero until following fields are valid */ @@ -283,38 +293,14 @@ static const struct attribute_group fscher_group = { * Real code */ -static int fscher_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, fscher_detect); -} - -static int fscher_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int fscher_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info) { - struct i2c_client *new_client; - struct fscher_data *data; - int err = 0; + struct i2c_adapter *adapter = new_client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - /* OK. For now, we presume we have a valid client. We now create the - * client structure, even though we cannot fill it completely yet. - * But it allows us to access i2c_smbus_read_byte_data. */ - if (!(data = kzalloc(sizeof(struct fscher_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - /* The common I2C client data is placed right before the - * Hermes-specific data. */ - new_client = &data->client; - i2c_set_clientdata(new_client, data); - new_client->addr = address; - new_client->adapter = adapter; - new_client->driver = &fscher_driver; - new_client->flags = 0; + return -ENODEV; /* Do the remaining detection unless force or force_fscher parameter */ if (kind < 0) { @@ -324,24 +310,35 @@ static int fscher_detect(struct i2c_adapter *adapter, int address, int kind) FSCHER_REG_IDENT_1) != 0x45) /* 'E' */ || (i2c_smbus_read_byte_data(new_client, FSCHER_REG_IDENT_2) != 0x52)) /* 'R' */ - goto exit_free; + return -ENODEV; + } + + strlcpy(info->type, "fscher", I2C_NAME_SIZE); + + return 0; +} + +static int fscher_probe(struct i2c_client *new_client, + const struct i2c_device_id *id) +{ + struct fscher_data *data; + int err; + + data = kzalloc(sizeof(struct fscher_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; } - /* Fill in the remaining client fields and put it into the - * global list */ - strlcpy(new_client->name, "fscher", I2C_NAME_SIZE); + i2c_set_clientdata(new_client, data); data->valid = 0; mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(new_client))) - goto exit_free; - fscher_init_client(new_client); /* Register sysfs hooks */ if ((err = sysfs_create_group(&new_client->dev.kobj, &fscher_group))) - goto exit_detach; + goto exit_free; data->hwmon_dev = hwmon_device_register(&new_client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -353,25 +350,19 @@ static int fscher_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove_files: sysfs_remove_group(&new_client->dev.kobj, &fscher_group); -exit_detach: - i2c_detach_client(new_client); exit_free: kfree(data); exit: return err; } -static int fscher_detach_client(struct i2c_client *client) +static int fscher_remove(struct i2c_client *client) { struct fscher_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &fscher_group); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } diff --git a/drivers/hwmon/fschmd.c b/drivers/hwmon/fschmd.c index bd89d270a5e..96717036893 100644 --- a/drivers/hwmon/fschmd.c +++ b/drivers/hwmon/fschmd.c @@ -171,20 +171,37 @@ static const int FSCHMD_NO_TEMP_SENSORS[5] = { 3, 3, 4, 3, 5 }; * Functions declarations */ -static int fschmd_attach_adapter(struct i2c_adapter *adapter); -static int fschmd_detach_client(struct i2c_client *client); +static int fschmd_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int fschmd_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int fschmd_remove(struct i2c_client *client); static struct fschmd_data *fschmd_update_device(struct device *dev); /* * Driver data (common to all clients) */ +static const struct i2c_device_id fschmd_id[] = { + { "fscpos", fscpos }, + { "fscher", fscher }, + { "fscscy", fscscy }, + { "fschrc", fschrc }, + { "fschmd", fschmd }, + { } +}; +MODULE_DEVICE_TABLE(i2c, fschmd_id); + static struct i2c_driver fschmd_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = FSCHMD_NAME, }, - .attach_adapter = fschmd_attach_adapter, - .detach_client = fschmd_detach_client, + .probe = fschmd_probe, + .remove = fschmd_remove, + .id_table = fschmd_id, + .detect = fschmd_detect, + .address_data = &addr_data, }; /* @@ -192,7 +209,6 @@ static struct i2c_driver fschmd_driver = { */ struct fschmd_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; int kind; @@ -269,7 +285,7 @@ static ssize_t store_temp_max(struct device *dev, struct device_attribute v = SENSORS_LIMIT(v, -128, 127) + 128; mutex_lock(&data->update_lock); - i2c_smbus_write_byte_data(&data->client, + i2c_smbus_write_byte_data(to_i2c_client(dev), FSCHMD_REG_TEMP_LIMIT[data->kind][index], v); data->temp_max[index] = v; mutex_unlock(&data->update_lock); @@ -346,14 +362,14 @@ static ssize_t store_fan_div(struct device *dev, struct device_attribute mutex_lock(&data->update_lock); - reg = i2c_smbus_read_byte_data(&data->client, + reg = i2c_smbus_read_byte_data(to_i2c_client(dev), FSCHMD_REG_FAN_RIPPLE[data->kind][index]); /* bits 2..7 reserved => mask with 0x03 */ reg &= ~0x03; reg |= v; - i2c_smbus_write_byte_data(&data->client, + i2c_smbus_write_byte_data(to_i2c_client(dev), FSCHMD_REG_FAN_RIPPLE[data->kind][index], reg); data->fan_ripple[index] = reg; @@ -416,7 +432,7 @@ static ssize_t store_pwm_auto_point1_pwm(struct device *dev, mutex_lock(&data->update_lock); - i2c_smbus_write_byte_data(&data->client, + i2c_smbus_write_byte_data(to_i2c_client(dev), FSCHMD_REG_FAN_MIN[data->kind][index], v); data->fan_min[index] = v; @@ -448,14 +464,14 @@ static ssize_t store_alert_led(struct device *dev, mutex_lock(&data->update_lock); - reg = i2c_smbus_read_byte_data(&data->client, FSCHMD_REG_CONTROL); + reg = i2c_smbus_read_byte_data(to_i2c_client(dev), FSCHMD_REG_CONTROL); if (v) reg |= FSCHMD_CONTROL_ALERT_LED_MASK; else reg &= ~FSCHMD_CONTROL_ALERT_LED_MASK; - i2c_smbus_write_byte_data(&data->client, FSCHMD_REG_CONTROL, reg); + i2c_smbus_write_byte_data(to_i2c_client(dev), FSCHMD_REG_CONTROL, reg); data->global_control = reg; @@ -600,32 +616,15 @@ static void fschmd_dmi_decode(const struct dmi_header *header) } } -static int fschmd_detect(struct i2c_adapter *adapter, int address, int kind) +static int fschmd_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - struct i2c_client *client; - struct fschmd_data *data; - u8 revision; - const char * const names[5] = { "Poseidon", "Hermes", "Scylla", - "Heracles", "Heimdall" }; + struct i2c_adapter *adapter = client->adapter; const char * const client_names[5] = { "fscpos", "fscher", "fscscy", "fschrc", "fschmd" }; - int i, err = 0; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - return 0; - - /* OK. For now, we presume we have a valid client. We now create the - * client structure, even though we cannot fill it completely yet. - * But it allows us to access i2c_smbus_read_byte_data. */ - if (!(data = kzalloc(sizeof(struct fschmd_data), GFP_KERNEL))) - return -ENOMEM; - - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &fschmd_driver; - mutex_init(&data->update_lock); + return -ENODEV; /* Detect & Identify the chip */ if (kind <= 0) { @@ -650,9 +649,31 @@ static int fschmd_detect(struct i2c_adapter *adapter, int address, int kind) else if (!strcmp(id, "HMD")) kind = fschmd; else - goto exit_free; + return -ENODEV; } + strlcpy(info->type, client_names[kind - 1], I2C_NAME_SIZE); + + return 0; +} + +static int fschmd_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct fschmd_data *data; + u8 revision; + const char * const names[5] = { "Poseidon", "Hermes", "Scylla", + "Heracles", "Heimdall" }; + int i, err; + enum chips kind = id->driver_data; + + data = kzalloc(sizeof(struct fschmd_data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); + if (kind == fscpos) { /* The Poseidon has hardwired temp limits, fill these in for the alarm resetting code */ @@ -674,11 +695,6 @@ static int fschmd_detect(struct i2c_adapter *adapter, int address, int kind) /* i2c kind goes from 1-5, we want from 0-4 to address arrays */ data->kind = kind - 1; - strlcpy(client->name, client_names[data->kind], I2C_NAME_SIZE); - - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_free; for (i = 0; i < ARRAY_SIZE(fschmd_attr); i++) { err = device_create_file(&client->dev, @@ -726,25 +742,14 @@ static int fschmd_detect(struct i2c_adapter *adapter, int address, int kind) return 0; exit_detach: - fschmd_detach_client(client); /* will also free data for us */ - return err; - -exit_free: - kfree(data); + fschmd_remove(client); /* will also free data for us */ return err; } -static int fschmd_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, fschmd_detect); -} - -static int fschmd_detach_client(struct i2c_client *client) +static int fschmd_remove(struct i2c_client *client) { struct fschmd_data *data = i2c_get_clientdata(client); - int i, err; + int i; /* Check if registered in case we're called from fschmd_detect to cleanup after an error */ @@ -760,9 +765,6 @@ static int fschmd_detach_client(struct i2c_client *client) device_remove_file(&client->dev, &fschmd_fan_attr[i].dev_attr); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } diff --git a/drivers/hwmon/fscpos.c b/drivers/hwmon/fscpos.c index 00f48484e54..8a7bcf500b4 100644 --- a/drivers/hwmon/fscpos.c +++ b/drivers/hwmon/fscpos.c @@ -87,9 +87,11 @@ static u8 FSCPOS_REG_TEMP_STATE[] = { 0x71, 0x81, 0x91 }; /* * Functions declaration */ -static int fscpos_attach_adapter(struct i2c_adapter *adapter); -static int fscpos_detect(struct i2c_adapter *adapter, int address, int kind); -static int fscpos_detach_client(struct i2c_client *client); +static int fscpos_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int fscpos_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int fscpos_remove(struct i2c_client *client); static int fscpos_read_value(struct i2c_client *client, u8 reg); static int fscpos_write_value(struct i2c_client *client, u8 reg, u8 value); @@ -101,19 +103,27 @@ static void reset_fan_alarm(struct i2c_client *client, int nr); /* * Driver data (common to all clients) */ +static const struct i2c_device_id fscpos_id[] = { + { "fscpos", fscpos }, + { } +}; + static struct i2c_driver fscpos_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "fscpos", }, - .attach_adapter = fscpos_attach_adapter, - .detach_client = fscpos_detach_client, + .probe = fscpos_probe, + .remove = fscpos_remove, + .id_table = fscpos_id, + .detect = fscpos_detect, + .address_data = &addr_data, }; /* * Client data (each client gets its own) */ struct fscpos_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* 0 until following fields are valid */ @@ -470,39 +480,14 @@ static const struct attribute_group fscpos_group = { .attrs = fscpos_attributes, }; -static int fscpos_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, fscpos_detect); -} - -static int fscpos_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int fscpos_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info) { - struct i2c_client *new_client; - struct fscpos_data *data; - int err = 0; + struct i2c_adapter *adapter = new_client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - /* - * OK. For now, we presume we have a valid client. We now create the - * client structure, even though we cannot fill it completely yet. - * But it allows us to access fscpos_{read,write}_value. - */ - - if (!(data = kzalloc(sizeof(struct fscpos_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - new_client = &data->client; - i2c_set_clientdata(new_client, data); - new_client->addr = address; - new_client->adapter = adapter; - new_client->driver = &fscpos_driver; - new_client->flags = 0; + return -ENODEV; /* Do the remaining detection unless force or force_fscpos parameter */ if (kind < 0) { @@ -512,22 +497,30 @@ static int fscpos_detect(struct i2c_adapter *adapter, int address, int kind) != 0x45) /* 'E' */ || (fscpos_read_value(new_client, FSCPOS_REG_IDENT_2) != 0x47))/* 'G' */ - { - dev_dbg(&new_client->dev, "fscpos detection failed\n"); - goto exit_free; - } + return -ENODEV; } - /* Fill in the remaining client fields and put it in the global list */ - strlcpy(new_client->name, "fscpos", I2C_NAME_SIZE); + strlcpy(info->type, "fscpos", I2C_NAME_SIZE); + return 0; +} + +static int fscpos_probe(struct i2c_client *new_client, + const struct i2c_device_id *id) +{ + struct fscpos_data *data; + int err; + + data = kzalloc(sizeof(struct fscpos_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(new_client, data); data->valid = 0; mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(new_client))) - goto exit_free; - /* Inizialize the fscpos chip */ fscpos_init_client(new_client); @@ -536,7 +529,7 @@ static int fscpos_detect(struct i2c_adapter *adapter, int address, int kind) /* Register sysfs hooks */ if ((err = sysfs_create_group(&new_client->dev.kobj, &fscpos_group))) - goto exit_detach; + goto exit_free; data->hwmon_dev = hwmon_device_register(&new_client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -548,24 +541,19 @@ static int fscpos_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove_files: sysfs_remove_group(&new_client->dev.kobj, &fscpos_group); -exit_detach: - i2c_detach_client(new_client); exit_free: kfree(data); exit: return err; } -static int fscpos_detach_client(struct i2c_client *client) +static int fscpos_remove(struct i2c_client *client) { struct fscpos_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &fscpos_group); - if ((err = i2c_detach_client(client))) - return err; kfree(data); return 0; } diff --git a/drivers/hwmon/gl518sm.c b/drivers/hwmon/gl518sm.c index 33e9e8a8d1c..7820df45d77 100644 --- a/drivers/hwmon/gl518sm.c +++ b/drivers/hwmon/gl518sm.c @@ -114,7 +114,6 @@ static inline u8 FAN_TO_REG(long rpm, int div) /* Each client has this additional data */ struct gl518_data { - struct i2c_client client; struct device *hwmon_dev; enum chips type; @@ -138,21 +137,33 @@ struct gl518_data { u8 beep_enable; /* Boolean */ }; -static int gl518_attach_adapter(struct i2c_adapter *adapter); -static int gl518_detect(struct i2c_adapter *adapter, int address, int kind); +static int gl518_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int gl518_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); static void gl518_init_client(struct i2c_client *client); -static int gl518_detach_client(struct i2c_client *client); +static int gl518_remove(struct i2c_client *client); static int gl518_read_value(struct i2c_client *client, u8 reg); static int gl518_write_value(struct i2c_client *client, u8 reg, u16 value); static struct gl518_data *gl518_update_device(struct device *dev); +static const struct i2c_device_id gl518_id[] = { + { "gl518sm", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, gl518_id); + /* This is the driver that will be inserted */ static struct i2c_driver gl518_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "gl518sm", }, - .attach_adapter = gl518_attach_adapter, - .detach_client = gl518_detach_client, + .probe = gl518_probe, + .remove = gl518_remove, + .id_table = gl518_id, + .detect = gl518_detect, + .address_data = &addr_data, }; /* @@ -472,46 +483,23 @@ static const struct attribute_group gl518_group_r80 = { * Real code */ -static int gl518_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, gl518_detect); -} - -static int gl518_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int gl518_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { + struct i2c_adapter *adapter = client->adapter; int i; - struct i2c_client *client; - struct gl518_data *data; - int err = 0; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA)) - goto exit; - - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access gl518_{read,write}_value. */ - - if (!(data = kzalloc(sizeof(struct gl518_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - i2c_set_clientdata(client, data); - - client->addr = address; - client->adapter = adapter; - client->driver = &gl518_driver; + return -ENODEV; /* Now, we do the remaining detection. */ if (kind < 0) { if ((gl518_read_value(client, GL518_REG_CHIP_ID) != 0x80) || (gl518_read_value(client, GL518_REG_CONF) & 0x80)) - goto exit_free; + return -ENODEV; } /* Determine the chip type. */ @@ -526,19 +514,32 @@ static int gl518_detect(struct i2c_adapter *adapter, int address, int kind) dev_info(&adapter->dev, "Ignoring 'force' parameter for unknown " "chip at adapter %d, address 0x%02x\n", - i2c_adapter_id(adapter), address); - goto exit_free; + i2c_adapter_id(adapter), client->addr); + return -ENODEV; } } - /* Fill in the remaining client fields */ - strlcpy(client->name, "gl518sm", I2C_NAME_SIZE); - data->type = kind; - mutex_init(&data->update_lock); + strlcpy(info->type, "gl518sm", I2C_NAME_SIZE); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_free; + return 0; +} + +static int gl518_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct gl518_data *data; + int err, revision; + + data = kzalloc(sizeof(struct gl518_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + revision = gl518_read_value(client, GL518_REG_REVISION); + data->type = revision == 0x80 ? gl518sm_r80 : gl518sm_r00; + mutex_init(&data->update_lock); /* Initialize the GL518SM chip */ data->alarm_mask = 0xff; @@ -546,7 +547,7 @@ static int gl518_detect(struct i2c_adapter *adapter, int address, int kind) /* Register sysfs hooks */ if ((err = sysfs_create_group(&client->dev.kobj, &gl518_group))) - goto exit_detach; + goto exit_free; if (data->type == gl518sm_r80) if ((err = sysfs_create_group(&client->dev.kobj, &gl518_group_r80))) @@ -564,8 +565,6 @@ exit_remove_files: sysfs_remove_group(&client->dev.kobj, &gl518_group); if (data->type == gl518sm_r80) sysfs_remove_group(&client->dev.kobj, &gl518_group_r80); -exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: @@ -591,19 +590,15 @@ static void gl518_init_client(struct i2c_client *client) gl518_write_value(client, GL518_REG_CONF, 0x40 | regvalue); } -static int gl518_detach_client(struct i2c_client *client) +static int gl518_remove(struct i2c_client *client) { struct gl518_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &gl518_group); if (data->type == gl518sm_r80) sysfs_remove_group(&client->dev.kobj, &gl518_group_r80); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } diff --git a/drivers/hwmon/gl520sm.c b/drivers/hwmon/gl520sm.c index 8984ef14162..19616f2242b 100644 --- a/drivers/hwmon/gl520sm.c +++ b/drivers/hwmon/gl520sm.c @@ -79,26 +79,37 @@ static const u8 GL520_REG_TEMP_MAX_HYST[] = { 0x06, 0x18 }; * Function declarations */ -static int gl520_attach_adapter(struct i2c_adapter *adapter); -static int gl520_detect(struct i2c_adapter *adapter, int address, int kind); +static int gl520_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int gl520_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); static void gl520_init_client(struct i2c_client *client); -static int gl520_detach_client(struct i2c_client *client); +static int gl520_remove(struct i2c_client *client); static int gl520_read_value(struct i2c_client *client, u8 reg); static int gl520_write_value(struct i2c_client *client, u8 reg, u16 value); static struct gl520_data *gl520_update_device(struct device *dev); /* Driver data */ +static const struct i2c_device_id gl520_id[] = { + { "gl520sm", gl520sm }, + { } +}; +MODULE_DEVICE_TABLE(i2c, gl520_id); + static struct i2c_driver gl520_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "gl520sm", }, - .attach_adapter = gl520_attach_adapter, - .detach_client = gl520_detach_client, + .probe = gl520_probe, + .remove = gl520_remove, + .id_table = gl520_id, + .detect = gl520_detect, + .address_data = &addr_data, }; /* Client data */ struct gl520_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* zero until the following fields are valid */ @@ -669,37 +680,15 @@ static const struct attribute_group gl520_group_opt = { * Real code */ -static int gl520_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, gl520_detect); -} - -static int gl520_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int gl520_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - struct i2c_client *client; - struct gl520_data *data; - int err = 0; + struct i2c_adapter *adapter = client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA)) - goto exit; - - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access gl520_{read,write}_value. */ - - if (!(data = kzalloc(sizeof(struct gl520_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &gl520_driver; + return -ENODEV; /* Determine the chip type. */ if (kind < 0) { @@ -707,24 +696,36 @@ static int gl520_detect(struct i2c_adapter *adapter, int address, int kind) ((gl520_read_value(client, GL520_REG_REVISION) & 0x7f) != 0x00) || ((gl520_read_value(client, GL520_REG_CONF) & 0x80) != 0x00)) { dev_dbg(&client->dev, "Unknown chip type, skipping\n"); - goto exit_free; + return -ENODEV; } } - /* Fill in the remaining client fields */ - strlcpy(client->name, "gl520sm", I2C_NAME_SIZE); - mutex_init(&data->update_lock); + strlcpy(info->type, "gl520sm", I2C_NAME_SIZE); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_free; + return 0; +} + +static int gl520_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct gl520_data *data; + int err; + + data = kzalloc(sizeof(struct gl520_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); /* Initialize the GL520SM chip */ gl520_init_client(client); /* Register sysfs hooks */ if ((err = sysfs_create_group(&client->dev.kobj, &gl520_group))) - goto exit_detach; + goto exit_free; if (data->two_temps) { if ((err = device_create_file(&client->dev, @@ -764,8 +765,6 @@ static int gl520_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove_files: sysfs_remove_group(&client->dev.kobj, &gl520_group); sysfs_remove_group(&client->dev.kobj, &gl520_group_opt); -exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: @@ -811,18 +810,14 @@ static void gl520_init_client(struct i2c_client *client) gl520_write_value(client, GL520_REG_BEEP_MASK, data->beep_mask); } -static int gl520_detach_client(struct i2c_client *client) +static int gl520_remove(struct i2c_client *client) { struct gl520_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &gl520_group); sysfs_remove_group(&client->dev.kobj, &gl520_group_opt); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } diff --git a/drivers/hwmon/lm63.c b/drivers/hwmon/lm63.c index 11628700808..3195a265f0e 100644 --- a/drivers/hwmon/lm63.c +++ b/drivers/hwmon/lm63.c @@ -1,7 +1,7 @@ /* * lm63.c - driver for the National Semiconductor LM63 temperature sensor * with integrated fan control - * Copyright (C) 2004-2006 Jean Delvare <khali@linux-fr.org> + * Copyright (C) 2004-2008 Jean Delvare <khali@linux-fr.org> * Based on the lm90 driver. * * The LM63 is a sensor chip made by National Semiconductor. It measures @@ -128,24 +128,36 @@ I2C_CLIENT_INSMOD_1(lm63); * Functions declaration */ -static int lm63_attach_adapter(struct i2c_adapter *adapter); -static int lm63_detach_client(struct i2c_client *client); +static int lm63_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int lm63_remove(struct i2c_client *client); static struct lm63_data *lm63_update_device(struct device *dev); -static int lm63_detect(struct i2c_adapter *adapter, int address, int kind); +static int lm63_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); static void lm63_init_client(struct i2c_client *client); /* * Driver data (common to all clients) */ +static const struct i2c_device_id lm63_id[] = { + { "lm63", lm63 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, lm63_id); + static struct i2c_driver lm63_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "lm63", }, - .attach_adapter = lm63_attach_adapter, - .detach_client = lm63_detach_client, + .probe = lm63_probe, + .remove = lm63_remove, + .id_table = lm63_id, + .detect = lm63_detect, + .address_data = &addr_data, }; /* @@ -153,7 +165,6 @@ static struct i2c_driver lm63_driver = { */ struct lm63_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* zero until following fields are valid */ @@ -411,43 +422,14 @@ static const struct attribute_group lm63_group_fan1 = { * Real code */ -static int lm63_attach_adapter(struct i2c_adapter *adapter) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int lm63_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info) { - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, lm63_detect); -} - -/* - * The following function does more than just detection. If detection - * succeeds, it also registers the new chip. - */ -static int lm63_detect(struct i2c_adapter *adapter, int address, int kind) -{ - struct i2c_client *new_client; - struct lm63_data *data; - int err = 0; + struct i2c_adapter *adapter = new_client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct lm63_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - /* The common I2C client data is placed right before the - LM63-specific data. */ - new_client = &data->client; - i2c_set_clientdata(new_client, data); - new_client->addr = address; - new_client->adapter = adapter; - new_client->driver = &lm63_driver; - new_client->flags = 0; - - /* Default to an LM63 if forced */ - if (kind == 0) - kind = lm63; + return -ENODEV; if (kind < 0) { /* must identify */ u8 man_id, chip_id, reg_config1, reg_config2; @@ -477,25 +459,38 @@ static int lm63_detect(struct i2c_adapter *adapter, int address, int kind) dev_dbg(&adapter->dev, "Unsupported chip " "(man_id=0x%02X, chip_id=0x%02X).\n", man_id, chip_id); - goto exit_free; + return -ENODEV; } } - strlcpy(new_client->name, "lm63", I2C_NAME_SIZE); + strlcpy(info->type, "lm63", I2C_NAME_SIZE); + + return 0; +} + +static int lm63_probe(struct i2c_client *new_client, + const struct i2c_device_id *id) +{ + struct lm63_data *data; + int err; + + data = kzalloc(sizeof(struct lm63_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(new_client, data); data->valid = 0; mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(new_client))) - goto exit_free; - /* Initialize the LM63 chip */ lm63_init_client(new_client); /* Register sysfs hooks */ if ((err = sysfs_create_group(&new_client->dev.kobj, &lm63_group))) - goto exit_detach; + goto exit_free; if (data->config & 0x04) { /* tachometer enabled */ if ((err = sysfs_create_group(&new_client->dev.kobj, &lm63_group_fan1))) @@ -513,8 +508,6 @@ static int lm63_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove_files: sysfs_remove_group(&new_client->dev.kobj, &lm63_group); sysfs_remove_group(&new_client->dev.kobj, &lm63_group_fan1); -exit_detach: - i2c_detach_client(new_client); exit_free: kfree(data); exit: @@ -556,18 +549,14 @@ static void lm63_init_client(struct i2c_client *client) (data->config_fan & 0x20) ? "manual" : "auto"); } -static int lm63_detach_client(struct i2c_client *client) +static int lm63_remove(struct i2c_client *client) { struct lm63_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &lm63_group); sysfs_remove_group(&client->dev.kobj, &lm63_group_fan1); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } diff --git a/drivers/hwmon/lm77.c b/drivers/hwmon/lm77.c index 36d5a8c3ad8..866b401ab6e 100644 --- a/drivers/hwmon/lm77.c +++ b/drivers/hwmon/lm77.c @@ -52,7 +52,6 @@ I2C_CLIENT_INSMOD_1(lm77); /* Each client has this additional data */ struct lm77_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; @@ -65,23 +64,35 @@ struct lm77_data { u8 alarms; }; -static int lm77_attach_adapter(struct i2c_adapter *adapter); -static int lm77_detect(struct i2c_adapter *adapter, int address, int kind); +static int lm77_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int lm77_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); static void lm77_init_client(struct i2c_client *client); -static int lm77_detach_client(struct i2c_client *client); +static int lm77_remove(struct i2c_client *client); static u16 lm77_read_value(struct i2c_client *client, u8 reg); static int lm77_write_value(struct i2c_client *client, u8 reg, u16 value); static struct lm77_data *lm77_update_device(struct device *dev); +static const struct i2c_device_id lm77_id[] = { + { "lm77", lm77 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, lm77_id); + /* This is the driver that will be inserted */ static struct i2c_driver lm77_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "lm77", }, - .attach_adapter = lm77_attach_adapter, - .detach_client = lm77_detach_client, + .probe = lm77_probe, + .remove = lm77_remove, + .id_table = lm77_id, + .detect = lm77_detect, + .address_data = &addr_data, }; /* straight from the datasheet */ @@ -215,13 +226,6 @@ static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, 2); static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL, 0); static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 1); -static int lm77_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, lm77_detect); -} - static struct attribute *lm77_attributes[] = { &dev_attr_temp1_input.attr, &dev_attr_temp1_crit.attr, @@ -240,32 +244,15 @@ static const struct attribute_group lm77_group = { .attrs = lm77_attributes, }; -/* This function is called by i2c_probe */ -static int lm77_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int lm77_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info) { - struct i2c_client *new_client; - struct lm77_data *data; - int err = 0; - const char *name = ""; + struct i2c_adapter *adapter = new_client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA)) - goto exit; - - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access lm77_{read,write}_value. */ - if (!(data = kzalloc(sizeof(struct lm77_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - new_client = &data->client; - i2c_set_clientdata(new_client, data); - new_client->addr = address; - new_client->adapter = adapter; - new_client->driver = &lm77_driver; - new_client->flags = 0; + return -ENODEV; /* Here comes the remaining detection. Since the LM77 has no register dedicated to identification, we have to rely on the @@ -294,7 +281,7 @@ static int lm77_detect(struct i2c_adapter *adapter, int address, int kind) || i2c_smbus_read_word_data(new_client, i + 3) != crit || i2c_smbus_read_word_data(new_client, i + 4) != min || i2c_smbus_read_word_data(new_client, i + 5) != max) - goto exit_free; + return -ENODEV; /* sign bits */ if (((cur & 0x00f0) != 0xf0 && (cur & 0x00f0) != 0x0) @@ -302,51 +289,55 @@ static int lm77_detect(struct i2c_adapter *adapter, int address, int kind) || ((crit & 0x00f0) != 0xf0 && (crit & 0x00f0) != 0x0) || ((min & 0x00f0) != 0xf0 && (min & 0x00f0) != 0x0) || ((max & 0x00f0) != 0xf0 && (max & 0x00f0) != 0x0)) - goto exit_free; + return -ENODEV; /* unused bits */ if (conf & 0xe0) - goto exit_free; + return -ENODEV; /* 0x06 and 0x07 return the last read value */ cur = i2c_smbus_read_word_data(new_client, 0); if (i2c_smbus_read_word_data(new_client, 6) != cur || i2c_smbus_read_word_data(new_client, 7) != cur) - goto exit_free; + return -ENODEV; hyst = i2c_smbus_read_word_data(new_client, 2); if (i2c_smbus_read_word_data(new_client, 6) != hyst || i2c_smbus_read_word_data(new_client, 7) != hyst) - goto exit_free; + return -ENODEV; min = i2c_smbus_read_word_data(new_client, 4); if (i2c_smbus_read_word_data(new_client, 6) != min || i2c_smbus_read_word_data(new_client, 7) != min) - goto exit_free; + return -ENODEV; } - /* Determine the chip type - only one kind supported! */ - if (kind <= 0) - kind = lm77; + strlcpy(info->type, "lm77", I2C_NAME_SIZE); - if (kind == lm77) { - name = "lm77"; + return 0; +} + +static int lm77_probe(struct i2c_client *new_client, + const struct i2c_device_id *id) +{ + struct lm77_data *data; + int err; + + data = kzalloc(sizeof(struct lm77_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; } - /* Fill in the remaining client fields and put it into the global list */ - strlcpy(new_client->name, name, I2C_NAME_SIZE); + i2c_set_clientdata(new_client, data); data->valid = 0; mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(new_client))) - goto exit_free; - /* Initialize the LM77 chip */ lm77_init_client(new_client); /* Register sysfs hooks */ if ((err = sysfs_create_group(&new_client->dev.kobj, &lm77_group))) - goto exit_detach; + goto exit_free; data->hwmon_dev = hwmon_device_register(&new_client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -358,20 +349,17 @@ static int lm77_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove: sysfs_remove_group(&new_client->dev.kobj, &lm77_group); -exit_detach: - i2c_detach_client(new_client); exit_free: kfree(data); exit: return err; } -static int lm77_detach_client(struct i2c_client *client) +static int lm77_remove(struct i2c_client *client) { struct lm77_data *data = i2c_get_clientdata(client); hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &lm77_group); - i2c_detach_client(client); kfree(data); return 0; } diff --git a/drivers/hwmon/lm80.c b/drivers/hwmon/lm80.c index 26c91c9d476..bcffc189940 100644 --- a/drivers/hwmon/lm80.c +++ b/drivers/hwmon/lm80.c @@ -108,7 +108,6 @@ static inline long TEMP_FROM_REG(u16 temp) */ struct lm80_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* !=0 if following fields are valid */ @@ -132,10 +131,12 @@ struct lm80_data { * Functions declaration */ -static int lm80_attach_adapter(struct i2c_adapter *adapter); -static int lm80_detect(struct i2c_adapter *adapter, int address, int kind); +static int lm80_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int lm80_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); static void lm80_init_client(struct i2c_client *client); -static int lm80_detach_client(struct i2c_client *client); +static int lm80_remove(struct i2c_client *client); static struct lm80_data *lm80_update_device(struct device *dev); static int lm80_read_value(struct i2c_client *client, u8 reg); static int lm80_write_value(struct i2c_client *client, u8 reg, u8 value); @@ -144,12 +145,22 @@ static int lm80_write_value(struct i2c_client *client, u8 reg, u8 value); * Driver data (common to all clients) */ +static const struct i2c_device_id lm80_id[] = { + { "lm80", lm80 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, lm80_id); + static struct i2c_driver lm80_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "lm80", }, - .attach_adapter = lm80_attach_adapter, - .detach_client = lm80_detach_client, + .probe = lm80_probe, + .remove = lm80_remove, + .id_table = lm80_id, + .detect = lm80_detect, + .address_data = &addr_data, }; /* @@ -383,13 +394,6 @@ static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, 13); * Real code */ -static int lm80_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, lm80_detect); -} - static struct attribute *lm80_attributes[] = { &sensor_dev_attr_in0_min.dev_attr.attr, &sensor_dev_attr_in1_min.dev_attr.attr, @@ -442,53 +446,46 @@ static const struct attribute_group lm80_group = { .attrs = lm80_attributes, }; -static int lm80_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int lm80_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { + struct i2c_adapter *adapter = client->adapter; int i, cur; - struct i2c_client *client; - struct lm80_data *data; - int err = 0; - const char *name; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access lm80_{read,write}_value. */ - if (!(data = kzalloc(sizeof(struct lm80_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &lm80_driver; + return -ENODEV; /* Now, we do the remaining detection. It is lousy. */ if (lm80_read_value(client, LM80_REG_ALARM2) & 0xc0) - goto error_free; + return -ENODEV; for (i = 0x2a; i <= 0x3d; i++) { cur = i2c_smbus_read_byte_data(client, i); if ((i2c_smbus_read_byte_data(client, i + 0x40) != cur) || (i2c_smbus_read_byte_data(client, i + 0x80) != cur) || (i2c_smbus_read_byte_data(client, i + 0xc0) != cur)) - goto error_free; + return -ENODEV; } - /* Determine the chip type - only one kind supported! */ - kind = lm80; - name = "lm80"; + strlcpy(info->type, "lm80", I2C_NAME_SIZE); - /* Fill in the remaining client fields */ - strlcpy(client->name, name, I2C_NAME_SIZE); - mutex_init(&data->update_lock); + return 0; +} - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto error_free; +static int lm80_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct lm80_data *data; + int err; + + data = kzalloc(sizeof(struct lm80_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); /* Initialize the LM80 chip */ lm80_init_client(client); @@ -499,7 +496,7 @@ static int lm80_detect(struct i2c_adapter *adapter, int address, int kind) /* Register sysfs hooks */ if ((err = sysfs_create_group(&client->dev.kobj, &lm80_group))) - goto error_detach; + goto error_free; data->hwmon_dev = hwmon_device_register(&client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -511,23 +508,18 @@ static int lm80_detect(struct i2c_adapter *adapter, int address, int kind) error_remove: sysfs_remove_group(&client->dev.kobj, &lm80_group); -error_detach: - i2c_detach_client(client); error_free: kfree(data); exit: return err; } -static int lm80_detach_client(struct i2c_client *client) +static int lm80_remove(struct i2c_client *client) { struct lm80_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &lm80_group); - if ((err = i2c_detach_client(client))) - return err; kfree(data); return 0; diff --git a/drivers/hwmon/lm83.c b/drivers/hwmon/lm83.c index 6a8642fa25f..e59e2d1f080 100644 --- a/drivers/hwmon/lm83.c +++ b/drivers/hwmon/lm83.c @@ -1,7 +1,7 @@ /* * lm83.c - Part of lm_sensors, Linux kernel modules for hardware * monitoring - * Copyright (C) 2003-2006 Jean Delvare <khali@linux-fr.org> + * Copyright (C) 2003-2008 Jean Delvare <khali@linux-fr.org> * * Heavily inspired from the lm78, lm75 and adm1021 drivers. The LM83 is * a sensor chip made by National Semiconductor. It reports up to four @@ -118,21 +118,34 @@ static const u8 LM83_REG_W_HIGH[] = { * Functions declaration */ -static int lm83_attach_adapter(struct i2c_adapter *adapter); -static int lm83_detect(struct i2c_adapter *adapter, int address, int kind); -static int lm83_detach_client(struct i2c_client *client); +static int lm83_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info); +static int lm83_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int lm83_remove(struct i2c_client *client); static struct lm83_data *lm83_update_device(struct device *dev); /* * Driver data (common to all clients) */ +static const struct i2c_device_id lm83_id[] = { + { "lm83", lm83 }, + { "lm82", lm82 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, lm83_id); + static struct i2c_driver lm83_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "lm83", }, - .attach_adapter = lm83_attach_adapter, - .detach_client = lm83_detach_client, + .probe = lm83_probe, + .remove = lm83_remove, + .id_table = lm83_id, + .detect = lm83_detect, + .address_data = &addr_data, }; /* @@ -140,7 +153,6 @@ static struct i2c_driver lm83_driver = { */ struct lm83_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* zero until following fields are valid */ @@ -278,40 +290,15 @@ static const struct attribute_group lm83_group_opt = { * Real code */ -static int lm83_attach_adapter(struct i2c_adapter *adapter) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int lm83_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info) { - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, lm83_detect); -} - -/* - * The following function does more than just detection. If detection - * succeeds, it also registers the new chip. - */ -static int lm83_detect(struct i2c_adapter *adapter, int address, int kind) -{ - struct i2c_client *new_client; - struct lm83_data *data; - int err = 0; + struct i2c_adapter *adapter = new_client->adapter; const char *name = ""; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct lm83_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - /* The common I2C client data is placed right after the - * LM83-specific data. */ - new_client = &data->client; - i2c_set_clientdata(new_client, data); - new_client->addr = address; - new_client->adapter = adapter; - new_client->driver = &lm83_driver; - new_client->flags = 0; + return -ENODEV; /* Now we do the detection and identification. A negative kind * means that the driver was loaded with no force parameter @@ -335,8 +322,9 @@ static int lm83_detect(struct i2c_adapter *adapter, int address, int kind) ((i2c_smbus_read_byte_data(new_client, LM83_REG_R_CONFIG) & 0x41) != 0x00)) { dev_dbg(&adapter->dev, - "LM83 detection failed at 0x%02x.\n", address); - goto exit_free; + "LM83 detection failed at 0x%02x.\n", + new_client->addr); + return -ENODEV; } } @@ -361,7 +349,7 @@ static int lm83_detect(struct i2c_adapter *adapter, int address, int kind) dev_info(&adapter->dev, "Unsupported chip (man_id=0x%02X, " "chip_id=0x%02X).\n", man_id, chip_id); - goto exit_free; + return -ENODEV; } } @@ -372,15 +360,27 @@ static int lm83_detect(struct i2c_adapter *adapter, int address, int kind) name = "lm82"; } - /* We can fill in the remaining client fields */ - strlcpy(new_client->name, name, I2C_NAME_SIZE); + strlcpy(info->type, name, I2C_NAME_SIZE); + + return 0; +} + +static int lm83_probe(struct i2c_client *new_client, + const struct i2c_device_id *id) +{ + struct lm83_data *data; + int err; + + data = kzalloc(sizeof(struct lm83_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(new_client, data); data->valid = 0; mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(new_client))) - goto exit_free; - /* * Register sysfs hooks * The LM82 can only monitor one external diode which is @@ -389,9 +389,9 @@ static int lm83_detect(struct i2c_adapter *adapter, int address, int kind) */ if ((err = sysfs_create_group(&new_client->dev.kobj, &lm83_group))) - goto exit_detach; + goto exit_free; - if (kind == lm83) { + if (id->driver_data == lm83) { if ((err = sysfs_create_group(&new_client->dev.kobj, &lm83_group_opt))) goto exit_remove_files; @@ -408,26 +408,20 @@ static int lm83_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove_files: sysfs_remove_group(&new_client->dev.kobj, &lm83_group); sysfs_remove_group(&new_client->dev.kobj, &lm83_group_opt); -exit_detach: - i2c_detach_client(new_client); exit_free: kfree(data); exit: return err; } -static int lm83_detach_client(struct i2c_client *client) +static int lm83_remove(struct i2c_client *client) { struct lm83_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &lm83_group); sysfs_remove_group(&client->dev.kobj, &lm83_group_opt); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } diff --git a/drivers/hwmon/lm87.c b/drivers/hwmon/lm87.c index e1c183f0aae..21970f0d53a 100644 --- a/drivers/hwmon/lm87.c +++ b/drivers/hwmon/lm87.c @@ -5,7 +5,7 @@ * Philip Edelbrock <phil@netroedge.com> * Stephen Rousset <stephen.rousset@rocketlogix.com> * Dan Eaton <dan.eaton@rocketlogix.com> - * Copyright (C) 2004,2007 Jean Delvare <khali@linux-fr.org> + * Copyright (C) 2004-2008 Jean Delvare <khali@linux-fr.org> * * Original port to Linux 2.6 by Jeff Oliver. * @@ -157,22 +157,35 @@ static u8 LM87_REG_TEMP_LOW[3] = { 0x3A, 0x38, 0x2C }; * Functions declaration */ -static int lm87_attach_adapter(struct i2c_adapter *adapter); -static int lm87_detect(struct i2c_adapter *adapter, int address, int kind); +static int lm87_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int lm87_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info); static void lm87_init_client(struct i2c_client *client); -static int lm87_detach_client(struct i2c_client *client); +static int lm87_remove(struct i2c_client *client); static struct lm87_data *lm87_update_device(struct device *dev); /* * Driver data (common to all clients) */ +static const struct i2c_device_id lm87_id[] = { + { "lm87", lm87 }, + { "adm1024", adm1024 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, lm87_id); + static struct i2c_driver lm87_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "lm87", }, - .attach_adapter = lm87_attach_adapter, - .detach_client = lm87_detach_client, + .probe = lm87_probe, + .remove = lm87_remove, + .id_table = lm87_id, + .detect = lm87_detect, + .address_data = &addr_data, }; /* @@ -180,7 +193,6 @@ static struct i2c_driver lm87_driver = { */ struct lm87_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* zero until following fields are valid */ @@ -562,13 +574,6 @@ static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_alarm, NULL, 15); * Real code */ -static int lm87_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, lm87_detect); -} - static struct attribute *lm87_attributes[] = { &dev_attr_in1_input.attr, &dev_attr_in1_min.attr, @@ -656,33 +661,15 @@ static const struct attribute_group lm87_group_opt = { .attrs = lm87_attributes_opt, }; -/* - * The following function does more than just detection. If detection - * succeeds, it also registers the new chip. - */ -static int lm87_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int lm87_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info) { - struct i2c_client *new_client; - struct lm87_data *data; - int err = 0; + struct i2c_adapter *adapter = new_client->adapter; static const char *names[] = { "lm87", "adm1024" }; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct lm87_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - /* The common I2C client data is placed right before the - LM87-specific data. */ - new_client = &data->client; - i2c_set_clientdata(new_client, data); - new_client->addr = address; - new_client->adapter = adapter; - new_client->driver = &lm87_driver; - new_client->flags = 0; + return -ENODEV; /* Default to an LM87 if forced */ if (kind == 0) @@ -704,20 +691,32 @@ static int lm87_detect(struct i2c_adapter *adapter, int address, int kind) || (lm87_read_value(new_client, LM87_REG_CONFIG) & 0x80)) { dev_dbg(&adapter->dev, "LM87 detection failed at 0x%02x.\n", - address); - goto exit_free; + new_client->addr); + return -ENODEV; } } - /* We can fill in the remaining client fields */ - strlcpy(new_client->name, names[kind - 1], I2C_NAME_SIZE); + strlcpy(info->type, names[kind - 1], I2C_NAME_SIZE); + + return 0; +} + +static int lm87_probe(struct i2c_client *new_client, + const struct i2c_device_id *id) +{ + struct lm87_data *data; + int err; + + data = kzalloc(sizeof(struct lm87_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(new_client, data); data->valid = 0; mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(new_client))) - goto exit_free; - /* Initialize the LM87 chip */ lm87_init_client(new_client); @@ -732,7 +731,7 @@ static int lm87_detect(struct i2c_adapter *adapter, int address, int kind) /* Register sysfs hooks */ if ((err = sysfs_create_group(&new_client->dev.kobj, &lm87_group))) - goto exit_detach; + goto exit_free; if (data->channel & CHAN_NO_FAN(0)) { if ((err = device_create_file(&new_client->dev, @@ -832,8 +831,6 @@ static int lm87_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove: sysfs_remove_group(&new_client->dev.kobj, &lm87_group); sysfs_remove_group(&new_client->dev.kobj, &lm87_group_opt); -exit_detach: - i2c_detach_client(new_client); exit_free: kfree(data); exit: @@ -877,18 +874,14 @@ static void lm87_init_client(struct i2c_client *client) } } -static int lm87_detach_client(struct i2c_client *client) +static int lm87_remove(struct i2c_client *client) { struct lm87_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &lm87_group); sysfs_remove_group(&client->dev.kobj, &lm87_group_opt); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c index d1a3da3dd8e..c24fe36ac78 100644 --- a/drivers/hwmon/lm90.c +++ b/drivers/hwmon/lm90.c @@ -187,23 +187,44 @@ I2C_CLIENT_INSMOD_7(lm90, adm1032, lm99, lm86, max6657, adt7461, max6680); * Functions declaration */ -static int lm90_attach_adapter(struct i2c_adapter *adapter); -static int lm90_detect(struct i2c_adapter *adapter, int address, - int kind); +static int lm90_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int lm90_probe(struct i2c_client *client, + const struct i2c_device_id *id); static void lm90_init_client(struct i2c_client *client); -static int lm90_detach_client(struct i2c_client *client); +static int lm90_remove(struct i2c_client *client); static struct lm90_data *lm90_update_device(struct device *dev); /* * Driver data (common to all clients) */ +static const struct i2c_device_id lm90_id[] = { + { "adm1032", adm1032 }, + { "adt7461", adt7461 }, + { "lm90", lm90 }, + { "lm86", lm86 }, + { "lm89", lm99 }, + { "lm99", lm99 }, /* Missing temperature offset */ + { "max6657", max6657 }, + { "max6658", max6657 }, + { "max6659", max6657 }, + { "max6680", max6680 }, + { "max6681", max6680 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, lm90_id); + static struct i2c_driver lm90_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "lm90", }, - .attach_adapter = lm90_attach_adapter, - .detach_client = lm90_detach_client, + .probe = lm90_probe, + .remove = lm90_remove, + .id_table = lm90_id, + .detect = lm90_detect, + .address_data = &addr_data, }; /* @@ -211,7 +232,6 @@ static struct i2c_driver lm90_driver = { */ struct lm90_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* zero until following fields are valid */ @@ -477,40 +497,16 @@ static int lm90_read_reg(struct i2c_client* client, u8 reg, u8 *value) return 0; } -static int lm90_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, lm90_detect); -} - -/* - * The following function does more than just detection. If detection - * succeeds, it also registers the new chip. - */ -static int lm90_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int lm90_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info) { - struct i2c_client *new_client; - struct lm90_data *data; - int err = 0; + struct i2c_adapter *adapter = new_client->adapter; + int address = new_client->addr; const char *name = ""; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct lm90_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - /* The common I2C client data is placed right before the - LM90-specific data. */ - new_client = &data->client; - i2c_set_clientdata(new_client, data); - new_client->addr = address; - new_client->adapter = adapter; - new_client->driver = &lm90_driver; - new_client->flags = 0; + return -ENODEV; /* * Now we do the remaining detection. A negative kind means that @@ -538,7 +534,7 @@ static int lm90_detect(struct i2c_adapter *adapter, int address, int kind) LM90_REG_R_CONFIG1)) < 0 || (reg_convrate = i2c_smbus_read_byte_data(new_client, LM90_REG_R_CONVRATE)) < 0) - goto exit_free; + return -ENODEV; if ((address == 0x4C || address == 0x4D) && man_id == 0x01) { /* National Semiconductor */ @@ -546,7 +542,7 @@ static int lm90_detect(struct i2c_adapter *adapter, int address, int kind) if ((reg_config2 = i2c_smbus_read_byte_data(new_client, LM90_REG_R_CONFIG2)) < 0) - goto exit_free; + return -ENODEV; if ((reg_config1 & 0x2A) == 0x00 && (reg_config2 & 0xF8) == 0x00 @@ -610,10 +606,11 @@ static int lm90_detect(struct i2c_adapter *adapter, int address, int kind) dev_info(&adapter->dev, "Unsupported chip (man_id=0x%02X, " "chip_id=0x%02X).\n", man_id, chip_id); - goto exit_free; + return -ENODEV; } } + /* Fill the i2c board info */ if (kind == lm90) { name = "lm90"; } else if (kind == adm1032) { @@ -621,7 +618,7 @@ static int lm90_detect(struct i2c_adapter *adapter, int address, int kind) /* The ADM1032 supports PEC, but only if combined transactions are not used. */ if (i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE)) - new_client->flags |= I2C_CLIENT_PEC; + info->flags |= I2C_CLIENT_PEC; } else if (kind == lm99) { name = "lm99"; } else if (kind == lm86) { @@ -633,23 +630,39 @@ static int lm90_detect(struct i2c_adapter *adapter, int address, int kind) } else if (kind == adt7461) { name = "adt7461"; } + strlcpy(info->type, name, I2C_NAME_SIZE); + + return 0; +} + +static int lm90_probe(struct i2c_client *new_client, + const struct i2c_device_id *id) +{ + struct i2c_adapter *adapter = to_i2c_adapter(new_client->dev.parent); + struct lm90_data *data; + int err; - /* We can fill in the remaining client fields */ - strlcpy(new_client->name, name, I2C_NAME_SIZE); - data->valid = 0; - data->kind = kind; + data = kzalloc(sizeof(struct lm90_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + i2c_set_clientdata(new_client, data); mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(new_client))) - goto exit_free; + /* Set the device type */ + data->kind = id->driver_data; + if (data->kind == adm1032) { + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE)) + new_client->flags &= ~I2C_CLIENT_PEC; + } /* Initialize the LM90 chip */ lm90_init_client(new_client); /* Register sysfs hooks */ if ((err = sysfs_create_group(&new_client->dev.kobj, &lm90_group))) - goto exit_detach; + goto exit_free; if (new_client->flags & I2C_CLIENT_PEC) { if ((err = device_create_file(&new_client->dev, &dev_attr_pec))) @@ -672,8 +685,6 @@ static int lm90_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove_files: sysfs_remove_group(&new_client->dev.kobj, &lm90_group); device_remove_file(&new_client->dev, &dev_attr_pec); -exit_detach: - i2c_detach_client(new_client); exit_free: kfree(data); exit: @@ -710,10 +721,9 @@ static void lm90_init_client(struct i2c_client *client) i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1, config); } -static int lm90_detach_client(struct i2c_client *client) +static int lm90_remove(struct i2c_client *client) { struct lm90_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &lm90_group); @@ -722,9 +732,6 @@ static int lm90_detach_client(struct i2c_client *client) device_remove_file(&client->dev, &sensor_dev_attr_temp2_offset.dev_attr); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } diff --git a/drivers/hwmon/lm92.c b/drivers/hwmon/lm92.c index c31942e0824..b2e00c5a7ee 100644 --- a/drivers/hwmon/lm92.c +++ b/drivers/hwmon/lm92.c @@ -1,6 +1,6 @@ /* * lm92 - Hardware monitoring driver - * Copyright (C) 2005 Jean Delvare <khali@linux-fr.org> + * Copyright (C) 2005-2008 Jean Delvare <khali@linux-fr.org> * * Based on the lm90 driver, with some ideas taken from the lm_sensors * lm92 driver as well. @@ -96,7 +96,6 @@ static struct i2c_driver lm92_driver; /* Client data (each client gets its own) */ struct lm92_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* zero until following fields are valid */ @@ -319,32 +318,15 @@ static const struct attribute_group lm92_group = { .attrs = lm92_attributes, }; -/* The following function does more than just detection. If detection - succeeds, it also registers the new chip. */ -static int lm92_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int lm92_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info) { - struct i2c_client *new_client; - struct lm92_data *data; - int err = 0; - char *name; + struct i2c_adapter *adapter = new_client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct lm92_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - /* Fill in enough client fields so that we can read from the chip, - which is required for identication */ - new_client = &data->client; - i2c_set_clientdata(new_client, data); - new_client->addr = address; - new_client->adapter = adapter; - new_client->driver = &lm92_driver; - new_client->flags = 0; + return -ENODEV; /* A negative kind means that the driver was loaded with no force parameter (default), so we must identify the chip. */ @@ -364,34 +346,36 @@ static int lm92_detect(struct i2c_adapter *adapter, int address, int kind) kind = lm92; /* No separate prefix */ } else - goto exit_free; - } else - if (kind == 0) /* Default to an LM92 if forced */ - kind = lm92; - - /* Give it the proper name */ - if (kind == lm92) { - name = "lm92"; - } else { /* Supposedly cannot happen */ - dev_dbg(&new_client->dev, "Kind out of range?\n"); - goto exit_free; + return -ENODEV; } - /* Fill in the remaining client fields */ - strlcpy(new_client->name, name, I2C_NAME_SIZE); + strlcpy(info->type, "lm92", I2C_NAME_SIZE); + + return 0; +} + +static int lm92_probe(struct i2c_client *new_client, + const struct i2c_device_id *id) +{ + struct lm92_data *data; + int err; + + data = kzalloc(sizeof(struct lm92_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(new_client, data); data->valid = 0; mutex_init(&data->update_lock); - /* Tell the i2c subsystem a new client has arrived */ - if ((err = i2c_attach_client(new_client))) - goto exit_free; - /* Initialize the chipset */ lm92_init_client(new_client); /* Register sysfs hooks */ if ((err = sysfs_create_group(&new_client->dev.kobj, &lm92_group))) - goto exit_detach; + goto exit_free; data->hwmon_dev = hwmon_device_register(&new_client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -403,32 +387,19 @@ static int lm92_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove: sysfs_remove_group(&new_client->dev.kobj, &lm92_group); -exit_detach: - i2c_detach_client(new_client); exit_free: kfree(data); exit: return err; } -static int lm92_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, lm92_detect); -} - -static int lm92_detach_client(struct i2c_client *client) +static int lm92_remove(struct i2c_client *client) { struct lm92_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &lm92_group); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } @@ -438,12 +409,23 @@ static int lm92_detach_client(struct i2c_client *client) * Module and driver stuff */ +static const struct i2c_device_id lm92_id[] = { + { "lm92", lm92 }, + /* max6635 could be added here */ + { } +}; +MODULE_DEVICE_TABLE(i2c, lm92_id); + static struct i2c_driver lm92_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "lm92", }, - .attach_adapter = lm92_attach_adapter, - .detach_client = lm92_detach_client, + .probe = lm92_probe, + .remove = lm92_remove, + .id_table = lm92_id, + .detect = lm92_detect, + .address_data = &addr_data, }; static int __init sensors_lm92_init(void) diff --git a/drivers/hwmon/lm93.c b/drivers/hwmon/lm93.c index 5e678f5c883..fc36cadf36f 100644 --- a/drivers/hwmon/lm93.c +++ b/drivers/hwmon/lm93.c @@ -200,7 +200,6 @@ struct block1_t { * Client-specific data */ struct lm93_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; @@ -2501,45 +2500,14 @@ static void lm93_init_client(struct i2c_client *client) "chip to signal ready!\n"); } -static int lm93_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int lm93_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - struct lm93_data *data; - struct i2c_client *client; - - int err = -ENODEV, func; - void (*update)(struct lm93_data *, struct i2c_client *); - - /* choose update routine based on bus capabilities */ - func = i2c_get_functionality(adapter); - if ( ((LM93_SMBUS_FUNC_FULL & func) == LM93_SMBUS_FUNC_FULL) && - (!disable_block) ) { - dev_dbg(&adapter->dev,"using SMBus block data transactions\n"); - update = lm93_update_client_full; - } else if ((LM93_SMBUS_FUNC_MIN & func) == LM93_SMBUS_FUNC_MIN) { - dev_dbg(&adapter->dev,"disabled SMBus block data " - "transactions\n"); - update = lm93_update_client_min; - } else { - dev_dbg(&adapter->dev,"detect failed, " - "smbus byte and/or word data not supported!\n"); - goto err_out; - } + struct i2c_adapter *adapter = client->adapter; - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access lm78_{read,write}_value. */ - - if ( !(data = kzalloc(sizeof(struct lm93_data), GFP_KERNEL))) { - dev_dbg(&adapter->dev,"out of memory!\n"); - err = -ENOMEM; - goto err_out; - } - - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &lm93_driver; + if (!i2c_check_functionality(adapter, LM93_SMBUS_FUNC_MIN)) + return -ENODEV; /* detection */ if (kind < 0) { @@ -2548,7 +2516,7 @@ static int lm93_detect(struct i2c_adapter *adapter, int address, int kind) if (mfr != 0x01) { dev_dbg(&adapter->dev,"detect failed, " "bad manufacturer id 0x%02x!\n", mfr); - goto err_free; + return -ENODEV; } } @@ -2563,31 +2531,61 @@ static int lm93_detect(struct i2c_adapter *adapter, int address, int kind) if (kind == 0) dev_dbg(&adapter->dev, "(ignored 'force' parameter)\n"); - goto err_free; + return -ENODEV; } } - /* fill in remaining client fields */ - strlcpy(client->name, "lm93", I2C_NAME_SIZE); + strlcpy(info->type, "lm93", I2C_NAME_SIZE); dev_dbg(&adapter->dev,"loading %s at %d,0x%02x\n", client->name, i2c_adapter_id(client->adapter), client->addr); + return 0; +} + +static int lm93_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct lm93_data *data; + int err, func; + void (*update)(struct lm93_data *, struct i2c_client *); + + /* choose update routine based on bus capabilities */ + func = i2c_get_functionality(client->adapter); + if (((LM93_SMBUS_FUNC_FULL & func) == LM93_SMBUS_FUNC_FULL) && + (!disable_block)) { + dev_dbg(&client->dev, "using SMBus block data transactions\n"); + update = lm93_update_client_full; + } else if ((LM93_SMBUS_FUNC_MIN & func) == LM93_SMBUS_FUNC_MIN) { + dev_dbg(&client->dev, "disabled SMBus block data " + "transactions\n"); + update = lm93_update_client_min; + } else { + dev_dbg(&client->dev, "detect failed, " + "smbus byte and/or word data not supported!\n"); + err = -ENODEV; + goto err_out; + } + + data = kzalloc(sizeof(struct lm93_data), GFP_KERNEL); + if (!data) { + dev_dbg(&client->dev, "out of memory!\n"); + err = -ENOMEM; + goto err_out; + } + i2c_set_clientdata(client, data); + /* housekeeping */ data->valid = 0; data->update = update; mutex_init(&data->update_lock); - /* tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto err_free; - /* initialize the chip */ lm93_init_client(client); err = sysfs_create_group(&client->dev.kobj, &lm93_attr_grp); if (err) - goto err_detach; + goto err_free; /* Register hwmon driver class */ data->hwmon_dev = hwmon_device_register(&client->dev); @@ -2597,43 +2595,39 @@ static int lm93_detect(struct i2c_adapter *adapter, int address, int kind) err = PTR_ERR(data->hwmon_dev); dev_err(&client->dev, "error registering hwmon device.\n"); sysfs_remove_group(&client->dev.kobj, &lm93_attr_grp); -err_detach: - i2c_detach_client(client); err_free: kfree(data); err_out: return err; } -/* This function is called when: - * lm93_driver is inserted (when this module is loaded), for each - available adapter - * when a new adapter is inserted (and lm93_driver is still present) */ -static int lm93_attach_adapter(struct i2c_adapter *adapter) -{ - return i2c_probe(adapter, &addr_data, lm93_detect); -} - -static int lm93_detach_client(struct i2c_client *client) +static int lm93_remove(struct i2c_client *client) { struct lm93_data *data = i2c_get_clientdata(client); - int err = 0; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &lm93_attr_grp); - err = i2c_detach_client(client); - if (!err) - kfree(data); - return err; + kfree(data); + return 0; } +static const struct i2c_device_id lm93_id[] = { + { "lm93", lm93 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, lm93_id); + static struct i2c_driver lm93_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "lm93", }, - .attach_adapter = lm93_attach_adapter, - .detach_client = lm93_detach_client, + .probe = lm93_probe, + .remove = lm93_remove, + .id_table = lm93_id, + .detect = lm93_detect, + .address_data = &addr_data, }; static int __init lm93_init(void) diff --git a/drivers/hwmon/max1619.c b/drivers/hwmon/max1619.c index 7e7267a0454..1ab1cacad59 100644 --- a/drivers/hwmon/max1619.c +++ b/drivers/hwmon/max1619.c @@ -79,23 +79,34 @@ I2C_CLIENT_INSMOD_1(max1619); * Functions declaration */ -static int max1619_attach_adapter(struct i2c_adapter *adapter); -static int max1619_detect(struct i2c_adapter *adapter, int address, - int kind); +static int max1619_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int max1619_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); static void max1619_init_client(struct i2c_client *client); -static int max1619_detach_client(struct i2c_client *client); +static int max1619_remove(struct i2c_client *client); static struct max1619_data *max1619_update_device(struct device *dev); /* * Driver data (common to all clients) */ +static const struct i2c_device_id max1619_id[] = { + { "max1619", max1619 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, max1619_id); + static struct i2c_driver max1619_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "max1619", }, - .attach_adapter = max1619_attach_adapter, - .detach_client = max1619_detach_client, + .probe = max1619_probe, + .remove = max1619_remove, + .id_table = max1619_id, + .detect = max1619_detect, + .address_data = &addr_data, }; /* @@ -103,7 +114,6 @@ static struct i2c_driver max1619_driver = { */ struct max1619_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* zero until following fields are valid */ @@ -208,41 +218,15 @@ static const struct attribute_group max1619_group = { * Real code */ -static int max1619_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, max1619_detect); -} - -/* - * The following function does more than just detection. If detection - * succeeds, it also registers the new chip. - */ -static int max1619_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int max1619_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info) { - struct i2c_client *new_client; - struct max1619_data *data; - int err = 0; - const char *name = ""; + struct i2c_adapter *adapter = new_client->adapter; u8 reg_config=0, reg_convrate=0, reg_status=0; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct max1619_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - /* The common I2C client data is placed right before the - MAX1619-specific data. */ - new_client = &data->client; - i2c_set_clientdata(new_client, data); - new_client->addr = address; - new_client->adapter = adapter; - new_client->driver = &max1619_driver; - new_client->flags = 0; + return -ENODEV; /* * Now we do the remaining detection. A negative kind means that @@ -265,8 +249,8 @@ static int max1619_detect(struct i2c_adapter *adapter, int address, int kind) || reg_convrate > 0x07 || (reg_status & 0x61 ) !=0x00) { dev_dbg(&adapter->dev, "MAX1619 detection failed at 0x%02x.\n", - address); - goto exit_free; + new_client->addr); + return -ENODEV; } } @@ -285,28 +269,37 @@ static int max1619_detect(struct i2c_adapter *adapter, int address, int kind) dev_info(&adapter->dev, "Unsupported chip (man_id=0x%02X, " "chip_id=0x%02X).\n", man_id, chip_id); - goto exit_free; + return -ENODEV; } } - if (kind == max1619) - name = "max1619"; + strlcpy(info->type, "max1619", I2C_NAME_SIZE); + + return 0; +} + +static int max1619_probe(struct i2c_client *new_client, + const struct i2c_device_id *id) +{ + struct max1619_data *data; + int err; + + data = kzalloc(sizeof(struct max1619_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } - /* We can fill in the remaining client fields */ - strlcpy(new_client->name, name, I2C_NAME_SIZE); + i2c_set_clientdata(new_client, data); data->valid = 0; mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(new_client))) - goto exit_free; - /* Initialize the MAX1619 chip */ max1619_init_client(new_client); /* Register sysfs hooks */ if ((err = sysfs_create_group(&new_client->dev.kobj, &max1619_group))) - goto exit_detach; + goto exit_free; data->hwmon_dev = hwmon_device_register(&new_client->dev); if (IS_ERR(data->hwmon_dev)) { @@ -318,8 +311,6 @@ static int max1619_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove_files: sysfs_remove_group(&new_client->dev.kobj, &max1619_group); -exit_detach: - i2c_detach_client(new_client); exit_free: kfree(data); exit: @@ -341,17 +332,13 @@ static void max1619_init_client(struct i2c_client *client) config & 0xBF); /* run */ } -static int max1619_detach_client(struct i2c_client *client) +static int max1619_remove(struct i2c_client *client) { struct max1619_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &max1619_group); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; } diff --git a/drivers/hwmon/max6650.c b/drivers/hwmon/max6650.c index 52d528b76cc..f27af6a9da4 100644 --- a/drivers/hwmon/max6650.c +++ b/drivers/hwmon/max6650.c @@ -104,22 +104,34 @@ I2C_CLIENT_INSMOD_1(max6650); #define DIV_FROM_REG(reg) (1 << (reg & 7)) -static int max6650_attach_adapter(struct i2c_adapter *adapter); -static int max6650_detect(struct i2c_adapter *adapter, int address, int kind); +static int max6650_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int max6650_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); static int max6650_init_client(struct i2c_client *client); -static int max6650_detach_client(struct i2c_client *client); +static int max6650_remove(struct i2c_client *client); static struct max6650_data *max6650_update_device(struct device *dev); /* * Driver data (common to all clients) */ +static const struct i2c_device_id max6650_id[] = { + { "max6650", max6650 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, max6650_id); + static struct i2c_driver max6650_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "max6650", }, - .attach_adapter = max6650_attach_adapter, - .detach_client = max6650_detach_client, + .probe = max6650_probe, + .remove = max6650_remove, + .id_table = max6650_id, + .detect = max6650_detect, + .address_data = &addr_data, }; /* @@ -128,7 +140,6 @@ static struct i2c_driver max6650_driver = { struct max6650_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* zero until following fields are valid */ @@ -437,47 +448,21 @@ static struct attribute_group max6650_attr_grp = { * Real code */ -static int max6650_attach_adapter(struct i2c_adapter *adapter) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int max6650_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - if (!(adapter->class & I2C_CLASS_HWMON)) { - dev_dbg(&adapter->dev, - "FATAL: max6650_attach_adapter class HWMON not set\n"); - return 0; - } - - return i2c_probe(adapter, &addr_data, max6650_detect); -} - -/* - * The following function does more than just detection. If detection - * succeeds, it also registers the new chip. - */ - -static int max6650_detect(struct i2c_adapter *adapter, int address, int kind) -{ - struct i2c_client *client; - struct max6650_data *data; - int err = -ENODEV; + struct i2c_adapter *adapter = client->adapter; + int address = client->addr; dev_dbg(&adapter->dev, "max6650_detect called, kind = %d\n", kind); if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { dev_dbg(&adapter->dev, "max6650: I2C bus doesn't support " "byte read mode, skipping.\n"); - return 0; - } - - if (!(data = kzalloc(sizeof(struct max6650_data), GFP_KERNEL))) { - dev_err(&adapter->dev, "max6650: out of memory.\n"); - return -ENOMEM; + return -ENODEV; } - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &max6650_driver; - /* * Now we do the remaining detection. A negative kind means that * the driver was loaded with no force parameter (default), so we @@ -501,28 +486,40 @@ static int max6650_detect(struct i2c_adapter *adapter, int address, int kind) ||(i2c_smbus_read_byte_data(client, MAX6650_REG_COUNT) & 0xFC))) { dev_dbg(&adapter->dev, "max6650: detection failed at 0x%02x.\n", address); - goto err_free; + return -ENODEV; } dev_info(&adapter->dev, "max6650: chip found at 0x%02x.\n", address); - strlcpy(client->name, "max6650", I2C_NAME_SIZE); - mutex_init(&data->update_lock); + strlcpy(info->type, "max6650", I2C_NAME_SIZE); - if ((err = i2c_attach_client(client))) { - dev_err(&adapter->dev, "max6650: failed to attach client.\n"); - goto err_free; + return 0; +} + +static int max6650_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct max6650_data *data; + int err; + + if (!(data = kzalloc(sizeof(struct max6650_data), GFP_KERNEL))) { + dev_err(&client->dev, "out of memory.\n"); + return -ENOMEM; } + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); + /* * Initialize the max6650 chip */ - if (max6650_init_client(client)) - goto err_detach; + err = max6650_init_client(client); + if (err) + goto err_free; err = sysfs_create_group(&client->dev.kobj, &max6650_attr_grp); if (err) - goto err_detach; + goto err_free; data->hwmon_dev = hwmon_device_register(&client->dev); if (!IS_ERR(data->hwmon_dev)) @@ -531,24 +528,19 @@ static int max6650_detect(struct i2c_adapter *adapter, int address, int kind) err = PTR_ERR(data->hwmon_dev); dev_err(&client->dev, "error registering hwmon device.\n"); sysfs_remove_group(&client->dev.kobj, &max6650_attr_grp); -err_detach: - i2c_detach_client(client); err_free: kfree(data); return err; } -static int max6650_detach_client(struct i2c_client *client) +static int max6650_remove(struct i2c_client *client) { struct max6650_data *data = i2c_get_clientdata(client); - int err; sysfs_remove_group(&client->dev.kobj, &max6650_attr_grp); hwmon_device_unregister(data->hwmon_dev); - err = i2c_detach_client(client); - if (!err) - kfree(data); - return err; + kfree(data); + return 0; } static int max6650_init_client(struct i2c_client *client) diff --git a/drivers/hwmon/smsc47m192.c b/drivers/hwmon/smsc47m192.c index 3c9db6598ba..8bb5cb532d4 100644 --- a/drivers/hwmon/smsc47m192.c +++ b/drivers/hwmon/smsc47m192.c @@ -96,7 +96,6 @@ static inline int TEMP_FROM_REG(s8 val) } struct smsc47m192_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* !=0 if following fields are valid */ @@ -114,18 +113,29 @@ struct smsc47m192_data { u8 vrm; }; -static int smsc47m192_attach_adapter(struct i2c_adapter *adapter); -static int smsc47m192_detect(struct i2c_adapter *adapter, int address, - int kind); -static int smsc47m192_detach_client(struct i2c_client *client); +static int smsc47m192_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int smsc47m192_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int smsc47m192_remove(struct i2c_client *client); static struct smsc47m192_data *smsc47m192_update_device(struct device *dev); +static const struct i2c_device_id smsc47m192_id[] = { + { "smsc47m192", smsc47m192 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, smsc47m192_id); + static struct i2c_driver smsc47m192_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "smsc47m192", }, - .attach_adapter = smsc47m192_attach_adapter, - .detach_client = smsc47m192_detach_client, + .probe = smsc47m192_probe, + .remove = smsc47m192_remove, + .id_table = smsc47m192_id, + .detect = smsc47m192_detect, + .address_data = &addr_data, }; /* Voltages */ @@ -440,17 +450,6 @@ static const struct attribute_group smsc47m192_group_in4 = { .attrs = smsc47m192_attributes_in4, }; -/* This function is called when: - * smsc47m192_driver is inserted (when this module is loaded), for each - available adapter - * when a new adapter is inserted (and smsc47m192_driver is still present) */ -static int smsc47m192_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, smsc47m192_detect); -} - static void smsc47m192_init_client(struct i2c_client *client) { int i; @@ -481,31 +480,15 @@ static void smsc47m192_init_client(struct i2c_client *client) } } -/* This function is called by i2c_probe */ -static int smsc47m192_detect(struct i2c_adapter *adapter, int address, - int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int smsc47m192_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - struct i2c_client *client; - struct smsc47m192_data *data; - int err = 0; - int version, config; + struct i2c_adapter *adapter = client->adapter; + int version; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct smsc47m192_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &smsc47m192_driver; - - if (kind == 0) - kind = smsc47m192; + return -ENODEV; /* Detection criteria from sensors_detect script */ if (kind < 0) { @@ -523,26 +506,39 @@ static int smsc47m192_detect(struct i2c_adapter *adapter, int address, } else { dev_dbg(&adapter->dev, "SMSC47M192 detection failed at 0x%02x\n", - address); - goto exit_free; + client->addr); + return -ENODEV; } } - /* Fill in the remaining client fields and put into the global list */ - strlcpy(client->name, "smsc47m192", I2C_NAME_SIZE); + strlcpy(info->type, "smsc47m192", I2C_NAME_SIZE); + + return 0; +} + +static int smsc47m192_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct smsc47m192_data *data; + int config; + int err; + + data = kzalloc(sizeof(struct smsc47m192_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); data->vrm = vid_which_vrm(); mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_free; - /* Initialize the SMSC47M192 chip */ smsc47m192_init_client(client); /* Register sysfs hooks */ if ((err = sysfs_create_group(&client->dev.kobj, &smsc47m192_group))) - goto exit_detach; + goto exit_free; /* Pin 110 is either in4 (+12V) or VID4 */ config = i2c_smbus_read_byte_data(client, SMSC47M192_REG_CONFIG); @@ -563,26 +559,20 @@ static int smsc47m192_detect(struct i2c_adapter *adapter, int address, exit_remove_files: sysfs_remove_group(&client->dev.kobj, &smsc47m192_group); sysfs_remove_group(&client->dev.kobj, &smsc47m192_group_in4); -exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: return err; } -static int smsc47m192_detach_client(struct i2c_client *client) +static int smsc47m192_remove(struct i2c_client *client) { struct smsc47m192_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &smsc47m192_group); sysfs_remove_group(&client->dev.kobj, &smsc47m192_group_in4); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; diff --git a/drivers/hwmon/thmc50.c b/drivers/hwmon/thmc50.c index 76a3859c3fb..3b01001108c 100644 --- a/drivers/hwmon/thmc50.c +++ b/drivers/hwmon/thmc50.c @@ -60,7 +60,6 @@ static const u8 THMC50_REG_TEMP_MAX[] = { 0x39, 0x37, 0x2B }; /* Each client has this additional data */ struct thmc50_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; @@ -77,17 +76,31 @@ struct thmc50_data { u8 alarms; }; -static int thmc50_attach_adapter(struct i2c_adapter *adapter); -static int thmc50_detach_client(struct i2c_client *client); +static int thmc50_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int thmc50_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int thmc50_remove(struct i2c_client *client); static void thmc50_init_client(struct i2c_client *client); static struct thmc50_data *thmc50_update_device(struct device *dev); +static const struct i2c_device_id thmc50_id[] = { + { "adm1022", adm1022 }, + { "thmc50", thmc50 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, thmc50_id); + static struct i2c_driver thmc50_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "thmc50", }, - .attach_adapter = thmc50_attach_adapter, - .detach_client = thmc50_detach_client, + .probe = thmc50_probe, + .remove = thmc50_remove, + .id_table = thmc50_id, + .detect = thmc50_detect, + .address_data = &addr_data, }; static ssize_t show_analog_out(struct device *dev, @@ -250,39 +263,23 @@ static const struct attribute_group temp3_group = { .attrs = temp3_attributes, }; -static int thmc50_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int thmc50_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { unsigned company; unsigned revision; unsigned config; - struct i2c_client *client; - struct thmc50_data *data; - struct device *dev; + struct i2c_adapter *adapter = client->adapter; int err = 0; const char *type_name; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { pr_debug("thmc50: detect failed, " "smbus byte data not supported!\n"); - goto exit; - } - - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access thmc50 registers. */ - if (!(data = kzalloc(sizeof(struct thmc50_data), GFP_KERNEL))) { - pr_debug("thmc50: detect failed, kzalloc failed!\n"); - err = -ENOMEM; - goto exit; + return -ENODEV; } - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &thmc50_driver; - dev = &client->dev; - pr_debug("thmc50: Probing for THMC50 at 0x%2X on bus %d\n", client->addr, i2c_adapter_id(client->adapter)); @@ -307,21 +304,22 @@ static int thmc50_detect(struct i2c_adapter *adapter, int address, int kind) } if (err == -ENODEV) { pr_debug("thmc50: Detection of THMC50/ADM1022 failed\n"); - goto exit_free; + return err; } - data->type = kind; if (kind == adm1022) { int id = i2c_adapter_id(client->adapter); int i; type_name = "adm1022"; - data->has_temp3 = (config >> 7) & 1; /* config MSB */ for (i = 0; i + 1 < adm1022_temp3_num; i += 2) if (adm1022_temp3[i] == id && - adm1022_temp3[i + 1] == address) { + adm1022_temp3[i + 1] == client->addr) { /* enable 2nd remote temp */ - data->has_temp3 = 1; + config |= (1 << 7); + i2c_smbus_write_byte_data(client, + THMC50_REG_CONF, + config); break; } } else { @@ -330,19 +328,33 @@ static int thmc50_detect(struct i2c_adapter *adapter, int address, int kind) pr_debug("thmc50: Detected %s (version %x, revision %x)\n", type_name, (revision >> 4) - 0xc, revision & 0xf); - /* Fill in the remaining client fields & put it into the global list */ - strlcpy(client->name, type_name, I2C_NAME_SIZE); - mutex_init(&data->update_lock); + strlcpy(info->type, type_name, I2C_NAME_SIZE); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_free; + return 0; +} + +static int thmc50_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct thmc50_data *data; + int err; + + data = kzalloc(sizeof(struct thmc50_data), GFP_KERNEL); + if (!data) { + pr_debug("thmc50: detect failed, kzalloc failed!\n"); + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + data->type = id->driver_data; + mutex_init(&data->update_lock); thmc50_init_client(client); /* Register sysfs hooks */ if ((err = sysfs_create_group(&client->dev.kobj, &thmc50_group))) - goto exit_detach; + goto exit_free; /* Register ADM1022 sysfs hooks */ if (data->has_temp3) @@ -364,34 +376,21 @@ exit_remove_sysfs: sysfs_remove_group(&client->dev.kobj, &temp3_group); exit_remove_sysfs_thmc50: sysfs_remove_group(&client->dev.kobj, &thmc50_group); -exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: return err; } -static int thmc50_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, thmc50_detect); -} - -static int thmc50_detach_client(struct i2c_client *client) +static int thmc50_remove(struct i2c_client *client) { struct thmc50_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &thmc50_group); if (data->has_temp3) sysfs_remove_group(&client->dev.kobj, &temp3_group); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; @@ -412,8 +411,8 @@ static void thmc50_init_client(struct i2c_client *client) } config = i2c_smbus_read_byte_data(client, THMC50_REG_CONF); config |= 0x1; /* start the chip if it is in standby mode */ - if (data->has_temp3) - config |= 0x80; /* enable 2nd remote temp */ + if (data->type == adm1022 && (config & (1 << 7))) + data->has_temp3 = 1; i2c_smbus_write_byte_data(client, THMC50_REG_CONF, config); } diff --git a/drivers/hwmon/w83791d.c b/drivers/hwmon/w83791d.c index 85077c4c803..e4e91c9d480 100644 --- a/drivers/hwmon/w83791d.c +++ b/drivers/hwmon/w83791d.c @@ -247,7 +247,6 @@ static u8 div_to_reg(int nr, long val) } struct w83791d_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; @@ -286,9 +285,11 @@ struct w83791d_data { u8 vrm; /* hwmon-vid */ }; -static int w83791d_attach_adapter(struct i2c_adapter *adapter); -static int w83791d_detect(struct i2c_adapter *adapter, int address, int kind); -static int w83791d_detach_client(struct i2c_client *client); +static int w83791d_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int w83791d_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int w83791d_remove(struct i2c_client *client); static int w83791d_read(struct i2c_client *client, u8 register); static int w83791d_write(struct i2c_client *client, u8 register, u8 value); @@ -300,12 +301,22 @@ static void w83791d_print_debug(struct w83791d_data *data, struct device *dev); static void w83791d_init_client(struct i2c_client *client); +static const struct i2c_device_id w83791d_id[] = { + { "w83791d", w83791d }, + { } +}; +MODULE_DEVICE_TABLE(i2c, w83791d_id); + static struct i2c_driver w83791d_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "w83791d", }, - .attach_adapter = w83791d_attach_adapter, - .detach_client = w83791d_detach_client, + .probe = w83791d_probe, + .remove = w83791d_remove, + .id_table = w83791d_id, + .detect = w83791d_detect, + .address_data = &addr_data, }; /* following are the sysfs callback functions */ @@ -905,49 +916,12 @@ static const struct attribute_group w83791d_group = { .attrs = w83791d_attributes, }; -/* This function is called when: - * w83791d_driver is inserted (when this module is loaded), for each - available adapter - * when a new adapter is inserted (and w83791d_driver is still present) */ -static int w83791d_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, w83791d_detect); -} - -static int w83791d_create_subclient(struct i2c_adapter *adapter, - struct i2c_client *client, int addr, - struct i2c_client **sub_cli) -{ - int err; - struct i2c_client *sub_client; - - (*sub_cli) = sub_client = - kzalloc(sizeof(struct i2c_client), GFP_KERNEL); - if (!(sub_client)) { - return -ENOMEM; - } - sub_client->addr = 0x48 + addr; - i2c_set_clientdata(sub_client, NULL); - sub_client->adapter = adapter; - sub_client->driver = &w83791d_driver; - strlcpy(sub_client->name, "w83791d subclient", I2C_NAME_SIZE); - if ((err = i2c_attach_client(sub_client))) { - dev_err(&client->dev, "subclient registration " - "at address 0x%x failed\n", sub_client->addr); - kfree(sub_client); - return err; - } - return 0; -} - - -static int w83791d_detect_subclients(struct i2c_adapter *adapter, int address, - int kind, struct i2c_client *client) +static int w83791d_detect_subclients(struct i2c_client *client) { + struct i2c_adapter *adapter = client->adapter; struct w83791d_data *data = i2c_get_clientdata(client); + int address = client->addr; int i, id, err; u8 val; @@ -971,10 +945,7 @@ static int w83791d_detect_subclients(struct i2c_adapter *adapter, int address, val = w83791d_read(client, W83791D_REG_I2C_SUBADDR); if (!(val & 0x08)) { - err = w83791d_create_subclient(adapter, client, - val & 0x7, &data->lm75[0]); - if (err < 0) - goto error_sc_0; + data->lm75[0] = i2c_new_dummy(adapter, 0x48 + (val & 0x7)); } if (!(val & 0x80)) { if ((data->lm75[0] != NULL) && @@ -986,10 +957,8 @@ static int w83791d_detect_subclients(struct i2c_adapter *adapter, int address, err = -ENODEV; goto error_sc_1; } - err = w83791d_create_subclient(adapter, client, - (val >> 4) & 0x7, &data->lm75[1]); - if (err < 0) - goto error_sc_1; + data->lm75[1] = i2c_new_dummy(adapter, + 0x48 + ((val >> 4) & 0x7)); } return 0; @@ -997,53 +966,31 @@ static int w83791d_detect_subclients(struct i2c_adapter *adapter, int address, /* Undo inits in case of errors */ error_sc_1: - if (data->lm75[0] != NULL) { - i2c_detach_client(data->lm75[0]); - kfree(data->lm75[0]); - } + if (data->lm75[0] != NULL) + i2c_unregister_device(data->lm75[0]); error_sc_0: return err; } -static int w83791d_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int w83791d_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - struct i2c_client *client; - struct device *dev; - struct w83791d_data *data; - int i, val1, val2; - int err = 0; - const char *client_name = ""; + struct i2c_adapter *adapter = client->adapter; + int val1, val2; + unsigned short address = client->addr; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { - goto error0; + return -ENODEV; } - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access w83791d_{read,write}_value. */ - if (!(data = kzalloc(sizeof(struct w83791d_data), GFP_KERNEL))) { - err = -ENOMEM; - goto error0; - } - - client = &data->client; - dev = &client->dev; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &w83791d_driver; - mutex_init(&data->update_lock); - - /* Now, we do the remaining detection. */ - /* The w83791d may be stuck in some other bank than bank 0. This may make reading other information impossible. Specify a force=... parameter, and the Winbond will be reset to the right bank. */ if (kind < 0) { if (w83791d_read(client, W83791D_REG_CONFIG) & 0x80) { - dev_dbg(dev, "Detection failed at step 1\n"); - goto error1; + return -ENODEV; } val1 = w83791d_read(client, W83791D_REG_BANK); val2 = w83791d_read(client, W83791D_REG_CHIPMAN); @@ -1052,15 +999,13 @@ static int w83791d_detect(struct i2c_adapter *adapter, int address, int kind) /* yes it is Bank0 */ if (((!(val1 & 0x80)) && (val2 != 0xa3)) || ((val1 & 0x80) && (val2 != 0x5c))) { - dev_dbg(dev, "Detection failed at step 2\n"); - goto error1; + return -ENODEV; } } /* If Winbond chip, address of chip and W83791D_REG_I2C_ADDR should match */ if (w83791d_read(client, W83791D_REG_I2C_ADDR) != address) { - dev_dbg(dev, "Detection failed at step 3\n"); - goto error1; + return -ENODEV; } } @@ -1075,30 +1020,33 @@ static int w83791d_detect(struct i2c_adapter *adapter, int address, int kind) /* get vendor ID */ val2 = w83791d_read(client, W83791D_REG_CHIPMAN); if (val2 != 0x5c) { /* the vendor is NOT Winbond */ - dev_dbg(dev, "Detection failed at step 4\n"); - goto error1; + return -ENODEV; } val1 = w83791d_read(client, W83791D_REG_WCHIPID); if (val1 == 0x71) { kind = w83791d; } else { if (kind == 0) - dev_warn(dev, + dev_warn(&adapter->dev, "w83791d: Ignoring 'force' parameter " "for unknown chip at adapter %d, " "address 0x%02x\n", i2c_adapter_id(adapter), address); - goto error1; + return -ENODEV; } } - if (kind == w83791d) { - client_name = "w83791d"; - } else { - dev_err(dev, "w83791d: Internal error: unknown kind (%d)?!?\n", - kind); - goto error1; - } + strlcpy(info->type, "w83791d", I2C_NAME_SIZE); + + return 0; +} + +static int w83791d_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct w83791d_data *data; + struct device *dev = &client->dev; + int i, val1, err; #ifdef DEBUG val1 = w83791d_read(client, W83791D_REG_DID_VID4); @@ -1106,15 +1054,18 @@ static int w83791d_detect(struct i2c_adapter *adapter, int address, int kind) (val1 >> 5) & 0x07, (val1 >> 1) & 0x0f, val1); #endif - /* Fill in the remaining client fields and put into the global list */ - strlcpy(client->name, client_name, I2C_NAME_SIZE); + data = kzalloc(sizeof(struct w83791d_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto error0; + } - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto error1; + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); - if ((err = w83791d_detect_subclients(adapter, address, kind, client))) - goto error2; + err = w83791d_detect_subclients(client); + if (err) + goto error1; /* Initialize the chip */ w83791d_init_client(client); @@ -1141,43 +1092,29 @@ static int w83791d_detect(struct i2c_adapter *adapter, int address, int kind) error4: sysfs_remove_group(&client->dev.kobj, &w83791d_group); error3: - if (data->lm75[0] != NULL) { - i2c_detach_client(data->lm75[0]); - kfree(data->lm75[0]); - } - if (data->lm75[1] != NULL) { - i2c_detach_client(data->lm75[1]); - kfree(data->lm75[1]); - } -error2: - i2c_detach_client(client); + if (data->lm75[0] != NULL) + i2c_unregister_device(data->lm75[0]); + if (data->lm75[1] != NULL) + i2c_unregister_device(data->lm75[1]); error1: kfree(data); error0: return err; } -static int w83791d_detach_client(struct i2c_client *client) +static int w83791d_remove(struct i2c_client *client) { struct w83791d_data *data = i2c_get_clientdata(client); - int err; - - /* main client */ - if (data) { - hwmon_device_unregister(data->hwmon_dev); - sysfs_remove_group(&client->dev.kobj, &w83791d_group); - } - if ((err = i2c_detach_client(client))) - return err; + hwmon_device_unregister(data->hwmon_dev); + sysfs_remove_group(&client->dev.kobj, &w83791d_group); - /* main client */ - if (data) - kfree(data); - /* subclient */ - else - kfree(client); + if (data->lm75[0] != NULL) + i2c_unregister_device(data->lm75[0]); + if (data->lm75[1] != NULL) + i2c_unregister_device(data->lm75[1]); + kfree(data); return 0; } diff --git a/drivers/hwmon/w83792d.c b/drivers/hwmon/w83792d.c index 299629d47ed..cf94c5b0c87 100644 --- a/drivers/hwmon/w83792d.c +++ b/drivers/hwmon/w83792d.c @@ -267,9 +267,7 @@ DIV_TO_REG(long val) } struct w83792d_data { - struct i2c_client client; struct device *hwmon_dev; - enum chips type; struct mutex update_lock; char valid; /* !=0 if following fields are valid */ @@ -299,9 +297,11 @@ struct w83792d_data { u8 sf2_levels[3][4]; /* Smart FanII: Fan1,2,3 duty cycle levels */ }; -static int w83792d_attach_adapter(struct i2c_adapter *adapter); -static int w83792d_detect(struct i2c_adapter *adapter, int address, int kind); -static int w83792d_detach_client(struct i2c_client *client); +static int w83792d_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int w83792d_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int w83792d_remove(struct i2c_client *client); static struct w83792d_data *w83792d_update_device(struct device *dev); #ifdef DEBUG @@ -310,12 +310,22 @@ static void w83792d_print_debug(struct w83792d_data *data, struct device *dev); static void w83792d_init_client(struct i2c_client *client); +static const struct i2c_device_id w83792d_id[] = { + { "w83792d", w83792d }, + { } +}; +MODULE_DEVICE_TABLE(i2c, w83792d_id); + static struct i2c_driver w83792d_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "w83792d", }, - .attach_adapter = w83792d_attach_adapter, - .detach_client = w83792d_detach_client, + .probe = w83792d_probe, + .remove = w83792d_remove, + .id_table = w83792d_id, + .detect = w83792d_detect, + .address_data = &addr_data, }; static inline long in_count_from_reg(int nr, struct w83792d_data *data) @@ -864,53 +874,14 @@ store_sf2_level(struct device *dev, struct device_attribute *attr, return count; } -/* This function is called when: - * w83792d_driver is inserted (when this module is loaded), for each - available adapter - * when a new adapter is inserted (and w83792d_driver is still present) */ -static int -w83792d_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, w83792d_detect); -} - - -static int -w83792d_create_subclient(struct i2c_adapter *adapter, - struct i2c_client *new_client, int addr, - struct i2c_client **sub_cli) -{ - int err; - struct i2c_client *sub_client; - - (*sub_cli) = sub_client = kzalloc(sizeof(struct i2c_client), GFP_KERNEL); - if (!(sub_client)) { - return -ENOMEM; - } - sub_client->addr = 0x48 + addr; - i2c_set_clientdata(sub_client, NULL); - sub_client->adapter = adapter; - sub_client->driver = &w83792d_driver; - sub_client->flags = 0; - strlcpy(sub_client->name, "w83792d subclient", I2C_NAME_SIZE); - if ((err = i2c_attach_client(sub_client))) { - dev_err(&new_client->dev, "subclient registration " - "at address 0x%x failed\n", sub_client->addr); - kfree(sub_client); - return err; - } - return 0; -} - static int -w83792d_detect_subclients(struct i2c_adapter *adapter, int address, int kind, - struct i2c_client *new_client) +w83792d_detect_subclients(struct i2c_client *new_client) { int i, id, err; + int address = new_client->addr; u8 val; + struct i2c_adapter *adapter = new_client->adapter; struct w83792d_data *data = i2c_get_clientdata(new_client); id = i2c_adapter_id(adapter); @@ -932,10 +903,7 @@ w83792d_detect_subclients(struct i2c_adapter *adapter, int address, int kind, val = w83792d_read_value(new_client, W83792D_REG_I2C_SUBADDR); if (!(val & 0x08)) { - err = w83792d_create_subclient(adapter, new_client, val & 0x7, - &data->lm75[0]); - if (err < 0) - goto ERROR_SC_0; + data->lm75[0] = i2c_new_dummy(adapter, 0x48 + (val & 0x7)); } if (!(val & 0x80)) { if ((data->lm75[0] != NULL) && @@ -945,10 +913,8 @@ w83792d_detect_subclients(struct i2c_adapter *adapter, int address, int kind, err = -ENODEV; goto ERROR_SC_1; } - err = w83792d_create_subclient(adapter, new_client, - (val >> 4) & 0x7, &data->lm75[1]); - if (err < 0) - goto ERROR_SC_1; + data->lm75[1] = i2c_new_dummy(adapter, + 0x48 + ((val >> 4) & 0x7)); } return 0; @@ -956,10 +922,8 @@ w83792d_detect_subclients(struct i2c_adapter *adapter, int address, int kind, /* Undo inits in case of errors */ ERROR_SC_1: - if (data->lm75[0] != NULL) { - i2c_detach_client(data->lm75[0]); - kfree(data->lm75[0]); - } + if (data->lm75[0] != NULL) + i2c_unregister_device(data->lm75[0]); ERROR_SC_0: return err; } @@ -1294,47 +1258,25 @@ static const struct attribute_group w83792d_group = { .attrs = w83792d_attributes, }; +/* Return 0 if detection is successful, -ENODEV otherwise */ static int -w83792d_detect(struct i2c_adapter *adapter, int address, int kind) +w83792d_detect(struct i2c_client *client, int kind, struct i2c_board_info *info) { - int i = 0, val1 = 0, val2; - struct i2c_client *client; - struct device *dev; - struct w83792d_data *data; - int err = 0; - const char *client_name = ""; + struct i2c_adapter *adapter = client->adapter; + int val1, val2; + unsigned short address = client->addr; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { - goto ERROR0; - } - - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access w83792d_{read,write}_value. */ - - if (!(data = kzalloc(sizeof(struct w83792d_data), GFP_KERNEL))) { - err = -ENOMEM; - goto ERROR0; + return -ENODEV; } - client = &data->client; - dev = &client->dev; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &w83792d_driver; - client->flags = 0; - - /* Now, we do the remaining detection. */ - /* The w83792d may be stuck in some other bank than bank 0. This may make reading other information impossible. Specify a force=... or force_*=... parameter, and the Winbond will be reset to the right bank. */ if (kind < 0) { if (w83792d_read_value(client, W83792D_REG_CONFIG) & 0x80) { - dev_dbg(dev, "Detection failed at step 1\n"); - goto ERROR1; + return -ENODEV; } val1 = w83792d_read_value(client, W83792D_REG_BANK); val2 = w83792d_read_value(client, W83792D_REG_CHIPMAN); @@ -1342,16 +1284,14 @@ w83792d_detect(struct i2c_adapter *adapter, int address, int kind) if (!(val1 & 0x07)) { /* is Bank0 */ if (((!(val1 & 0x80)) && (val2 != 0xa3)) || ((val1 & 0x80) && (val2 != 0x5c))) { - dev_dbg(dev, "Detection failed at step 2\n"); - goto ERROR1; + return -ENODEV; } } /* If Winbond chip, address of chip and W83792D_REG_I2C_ADDR should match */ if (w83792d_read_value(client, W83792D_REG_I2C_ADDR) != address) { - dev_dbg(dev, "Detection failed at step 3\n"); - goto ERROR1; + return -ENODEV; } } @@ -1367,45 +1307,48 @@ w83792d_detect(struct i2c_adapter *adapter, int address, int kind) /* get vendor ID */ val2 = w83792d_read_value(client, W83792D_REG_CHIPMAN); if (val2 != 0x5c) { /* the vendor is NOT Winbond */ - goto ERROR1; + return -ENODEV; } val1 = w83792d_read_value(client, W83792D_REG_WCHIPID); if (val1 == 0x7a) { kind = w83792d; } else { if (kind == 0) - dev_warn(dev, + dev_warn(&adapter->dev, "w83792d: Ignoring 'force' parameter for" " unknown chip at adapter %d, address" " 0x%02x\n", i2c_adapter_id(adapter), address); - goto ERROR1; + return -ENODEV; } } - if (kind == w83792d) { - client_name = "w83792d"; - } else { - dev_err(dev, "w83792d: Internal error: unknown kind (%d)?!?\n", - kind); - goto ERROR1; - } + strlcpy(info->type, "w83792d", I2C_NAME_SIZE); + + return 0; +} + +static int +w83792d_probe(struct i2c_client *client, const struct i2c_device_id *id) +{ + struct w83792d_data *data; + struct device *dev = &client->dev; + int i, val1, err; - /* Fill in the remaining client fields and put into the global list */ - strlcpy(client->name, client_name, I2C_NAME_SIZE); - data->type = kind; + data = kzalloc(sizeof(struct w83792d_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto ERROR0; + } + i2c_set_clientdata(client, data); data->valid = 0; mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) + err = w83792d_detect_subclients(client); + if (err) goto ERROR1; - if ((err = w83792d_detect_subclients(adapter, address, - kind, client))) - goto ERROR2; - /* Initialize the chip */ w83792d_init_client(client); @@ -1457,16 +1400,10 @@ exit_remove_files: for (i = 0; i < ARRAY_SIZE(w83792d_group_fan); i++) sysfs_remove_group(&dev->kobj, &w83792d_group_fan[i]); ERROR3: - if (data->lm75[0] != NULL) { - i2c_detach_client(data->lm75[0]); - kfree(data->lm75[0]); - } - if (data->lm75[1] != NULL) { - i2c_detach_client(data->lm75[1]); - kfree(data->lm75[1]); - } -ERROR2: - i2c_detach_client(client); + if (data->lm75[0] != NULL) + i2c_unregister_device(data->lm75[0]); + if (data->lm75[1] != NULL) + i2c_unregister_device(data->lm75[1]); ERROR1: kfree(data); ERROR0: @@ -1474,30 +1411,23 @@ ERROR0: } static int -w83792d_detach_client(struct i2c_client *client) +w83792d_remove(struct i2c_client *client) { struct w83792d_data *data = i2c_get_clientdata(client); - int err, i; - - /* main client */ - if (data) { - hwmon_device_unregister(data->hwmon_dev); - sysfs_remove_group(&client->dev.kobj, &w83792d_group); - for (i = 0; i < ARRAY_SIZE(w83792d_group_fan); i++) - sysfs_remove_group(&client->dev.kobj, - &w83792d_group_fan[i]); - } + int i; - if ((err = i2c_detach_client(client))) - return err; + hwmon_device_unregister(data->hwmon_dev); + sysfs_remove_group(&client->dev.kobj, &w83792d_group); + for (i = 0; i < ARRAY_SIZE(w83792d_group_fan); i++) + sysfs_remove_group(&client->dev.kobj, + &w83792d_group_fan[i]); - /* main client */ - if (data) - kfree(data); - /* subclient */ - else - kfree(client); + if (data->lm75[0] != NULL) + i2c_unregister_device(data->lm75[0]); + if (data->lm75[1] != NULL) + i2c_unregister_device(data->lm75[1]); + kfree(data); return 0; } diff --git a/drivers/hwmon/w83793.c b/drivers/hwmon/w83793.c index ed3c019b78c..0a739f1c69b 100644 --- a/drivers/hwmon/w83793.c +++ b/drivers/hwmon/w83793.c @@ -179,7 +179,6 @@ static inline s8 TEMP_TO_REG(long val, s8 min, s8 max) } struct w83793_data { - struct i2c_client client; struct i2c_client *lm75[2]; struct device *hwmon_dev; struct mutex update_lock; @@ -226,19 +225,31 @@ struct w83793_data { static u8 w83793_read_value(struct i2c_client *client, u16 reg); static int w83793_write_value(struct i2c_client *client, u16 reg, u8 value); -static int w83793_attach_adapter(struct i2c_adapter *adapter); -static int w83793_detect(struct i2c_adapter *adapter, int address, int kind); -static int w83793_detach_client(struct i2c_client *client); +static int w83793_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int w83793_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int w83793_remove(struct i2c_client *client); static void w83793_init_client(struct i2c_client *client); static void w83793_update_nonvolatile(struct device *dev); static struct w83793_data *w83793_update_device(struct device *dev); +static const struct i2c_device_id w83793_id[] = { + { "w83793", w83793 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, w83793_id); + static struct i2c_driver w83793_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "w83793", }, - .attach_adapter = w83793_attach_adapter, - .detach_client = w83793_detach_client, + .probe = w83793_probe, + .remove = w83793_remove, + .id_table = w83793_id, + .detect = w83793_detect, + .address_data = &addr_data, }; static ssize_t @@ -1053,89 +1064,51 @@ static void w83793_init_client(struct i2c_client *client) } -static int w83793_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, w83793_detect); -} - -static int w83793_detach_client(struct i2c_client *client) +static int w83793_remove(struct i2c_client *client) { struct w83793_data *data = i2c_get_clientdata(client); struct device *dev = &client->dev; - int err, i; + int i; - /* main client */ - if (data) { - hwmon_device_unregister(data->hwmon_dev); + hwmon_device_unregister(data->hwmon_dev); - for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++) - device_remove_file(dev, - &w83793_sensor_attr_2[i].dev_attr); + for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++) + device_remove_file(dev, + &w83793_sensor_attr_2[i].dev_attr); - for (i = 0; i < ARRAY_SIZE(sda_single_files); i++) - device_remove_file(dev, &sda_single_files[i].dev_attr); + for (i = 0; i < ARRAY_SIZE(sda_single_files); i++) + device_remove_file(dev, &sda_single_files[i].dev_attr); - for (i = 0; i < ARRAY_SIZE(w83793_vid); i++) - device_remove_file(dev, &w83793_vid[i].dev_attr); - device_remove_file(dev, &dev_attr_vrm); + for (i = 0; i < ARRAY_SIZE(w83793_vid); i++) + device_remove_file(dev, &w83793_vid[i].dev_attr); + device_remove_file(dev, &dev_attr_vrm); - for (i = 0; i < ARRAY_SIZE(w83793_left_fan); i++) - device_remove_file(dev, &w83793_left_fan[i].dev_attr); + for (i = 0; i < ARRAY_SIZE(w83793_left_fan); i++) + device_remove_file(dev, &w83793_left_fan[i].dev_attr); - for (i = 0; i < ARRAY_SIZE(w83793_left_pwm); i++) - device_remove_file(dev, &w83793_left_pwm[i].dev_attr); + for (i = 0; i < ARRAY_SIZE(w83793_left_pwm); i++) + device_remove_file(dev, &w83793_left_pwm[i].dev_attr); - for (i = 0; i < ARRAY_SIZE(w83793_temp); i++) - device_remove_file(dev, &w83793_temp[i].dev_attr); - } + for (i = 0; i < ARRAY_SIZE(w83793_temp); i++) + device_remove_file(dev, &w83793_temp[i].dev_attr); - if ((err = i2c_detach_client(client))) - return err; + if (data->lm75[0] != NULL) + i2c_unregister_device(data->lm75[0]); + if (data->lm75[1] != NULL) + i2c_unregister_device(data->lm75[1]); - /* main client */ - if (data) - kfree(data); - /* subclient */ - else - kfree(client); + kfree(data); return 0; } static int -w83793_create_subclient(struct i2c_adapter *adapter, - struct i2c_client *client, int addr, - struct i2c_client **sub_cli) -{ - int err = 0; - struct i2c_client *sub_client; - - (*sub_cli) = sub_client = - kzalloc(sizeof(struct i2c_client), GFP_KERNEL); - if (!(sub_client)) { - return -ENOMEM; - } - sub_client->addr = 0x48 + addr; - i2c_set_clientdata(sub_client, NULL); - sub_client->adapter = adapter; - sub_client->driver = &w83793_driver; - strlcpy(sub_client->name, "w83793 subclient", I2C_NAME_SIZE); - if ((err = i2c_attach_client(sub_client))) { - dev_err(&client->dev, "subclient registration " - "at address 0x%x failed\n", sub_client->addr); - kfree(sub_client); - } - return err; -} - -static int -w83793_detect_subclients(struct i2c_adapter *adapter, int address, - int kind, struct i2c_client *client) +w83793_detect_subclients(struct i2c_client *client) { int i, id, err; + int address = client->addr; u8 tmp; + struct i2c_adapter *adapter = client->adapter; struct w83793_data *data = i2c_get_clientdata(client); id = i2c_adapter_id(adapter); @@ -1158,11 +1131,7 @@ w83793_detect_subclients(struct i2c_adapter *adapter, int address, tmp = w83793_read_value(client, W83793_REG_I2C_SUBADDR); if (!(tmp & 0x08)) { - err = - w83793_create_subclient(adapter, client, tmp & 0x7, - &data->lm75[0]); - if (err < 0) - goto ERROR_SC_0; + data->lm75[0] = i2c_new_dummy(adapter, 0x48 + (tmp & 0x7)); } if (!(tmp & 0x80)) { if ((data->lm75[0] != NULL) @@ -1173,10 +1142,8 @@ w83793_detect_subclients(struct i2c_adapter *adapter, int address, err = -ENODEV; goto ERROR_SC_1; } - err = w83793_create_subclient(adapter, client, - (tmp >> 4) & 0x7, &data->lm75[1]); - if (err < 0) - goto ERROR_SC_1; + data->lm75[1] = i2c_new_dummy(adapter, + 0x48 + ((tmp >> 4) & 0x7)); } return 0; @@ -1184,69 +1151,44 @@ w83793_detect_subclients(struct i2c_adapter *adapter, int address, /* Undo inits in case of errors */ ERROR_SC_1: - if (data->lm75[0] != NULL) { - i2c_detach_client(data->lm75[0]); - kfree(data->lm75[0]); - } + if (data->lm75[0] != NULL) + i2c_unregister_device(data->lm75[0]); ERROR_SC_0: return err; } -static int w83793_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int w83793_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - int i; - u8 tmp, val; - struct i2c_client *client; - struct device *dev; - struct w83793_data *data; - int files_fan = ARRAY_SIZE(w83793_left_fan) / 7; - int files_pwm = ARRAY_SIZE(w83793_left_pwm) / 5; - int files_temp = ARRAY_SIZE(w83793_temp) / 6; - int err = 0; + u8 tmp, bank; + struct i2c_adapter *adapter = client->adapter; + unsigned short address = client->addr; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { - goto exit; + return -ENODEV; } - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access w83793_{read,write}_value. */ - - if (!(data = kzalloc(sizeof(struct w83793_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - dev = &client->dev; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &w83793_driver; + bank = i2c_smbus_read_byte_data(client, W83793_REG_BANKSEL); - data->bank = i2c_smbus_read_byte_data(client, W83793_REG_BANKSEL); - - /* Now, we do the remaining detection. */ if (kind < 0) { - tmp = data->bank & 0x80 ? 0x5c : 0xa3; + tmp = bank & 0x80 ? 0x5c : 0xa3; /* Check Winbond vendor ID */ if (tmp != i2c_smbus_read_byte_data(client, W83793_REG_VENDORID)) { pr_debug("w83793: Detection failed at check " "vendor id\n"); - err = -ENODEV; - goto free_mem; + return -ENODEV; } /* If Winbond chip, address of chip and W83793_REG_I2C_ADDR should match */ - if ((data->bank & 0x07) == 0 + if ((bank & 0x07) == 0 && i2c_smbus_read_byte_data(client, W83793_REG_I2C_ADDR) != (address << 1)) { pr_debug("w83793: Detection failed at check " "i2c addr\n"); - err = -ENODEV; - goto free_mem; + return -ENODEV; } } @@ -1255,30 +1197,47 @@ static int w83793_detect(struct i2c_adapter *adapter, int address, int kind) Winbond. Determine the chip type now */ if (kind <= 0) { - if (0x7b == w83793_read_value(client, W83793_REG_CHIPID)) { + if (0x7b == i2c_smbus_read_byte_data(client, + W83793_REG_CHIPID)) { kind = w83793; } else { if (kind == 0) dev_warn(&adapter->dev, "w83793: Ignoring " "'force' parameter for unknown chip " "at address 0x%02x\n", address); - err = -ENODEV; - goto free_mem; + return -ENODEV; } } - /* Fill in the remaining client fields and put into the global list */ - strlcpy(client->name, "w83793", I2C_NAME_SIZE); + strlcpy(info->type, "w83793", I2C_NAME_SIZE); + + return 0; +} +static int w83793_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct device *dev = &client->dev; + struct w83793_data *data; + int i, tmp, val, err; + int files_fan = ARRAY_SIZE(w83793_left_fan) / 7; + int files_pwm = ARRAY_SIZE(w83793_left_pwm) / 5; + int files_temp = ARRAY_SIZE(w83793_temp) / 6; + + data = kzalloc(sizeof(struct w83793_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + data->bank = i2c_smbus_read_byte_data(client, W83793_REG_BANKSEL); mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) + err = w83793_detect_subclients(client); + if (err) goto free_mem; - if ((err = w83793_detect_subclients(adapter, address, kind, client))) - goto detach_client; - /* Initialize the chip */ w83793_init_client(client); @@ -1459,16 +1418,10 @@ exit_remove: for (i = 0; i < ARRAY_SIZE(w83793_temp); i++) device_remove_file(dev, &w83793_temp[i].dev_attr); - if (data->lm75[0] != NULL) { - i2c_detach_client(data->lm75[0]); - kfree(data->lm75[0]); - } - if (data->lm75[1] != NULL) { - i2c_detach_client(data->lm75[1]); - kfree(data->lm75[1]); - } -detach_client: - i2c_detach_client(client); + if (data->lm75[0] != NULL) + i2c_unregister_device(data->lm75[0]); + if (data->lm75[1] != NULL) + i2c_unregister_device(data->lm75[1]); free_mem: kfree(data); exit: diff --git a/drivers/hwmon/w83l785ts.c b/drivers/hwmon/w83l785ts.c index 52e268e25da..ea295b9fc4f 100644 --- a/drivers/hwmon/w83l785ts.c +++ b/drivers/hwmon/w83l785ts.c @@ -81,10 +81,11 @@ I2C_CLIENT_INSMOD_1(w83l785ts); * Functions declaration */ -static int w83l785ts_attach_adapter(struct i2c_adapter *adapter); -static int w83l785ts_detect(struct i2c_adapter *adapter, int address, - int kind); -static int w83l785ts_detach_client(struct i2c_client *client); +static int w83l785ts_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int w83l785ts_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int w83l785ts_remove(struct i2c_client *client); static u8 w83l785ts_read_value(struct i2c_client *client, u8 reg, u8 defval); static struct w83l785ts_data *w83l785ts_update_device(struct device *dev); @@ -92,12 +93,22 @@ static struct w83l785ts_data *w83l785ts_update_device(struct device *dev); * Driver data (common to all clients) */ +static const struct i2c_device_id w83l785ts_id[] = { + { "w83l785ts", w83l785ts }, + { } +}; +MODULE_DEVICE_TABLE(i2c, w83l785ts_id); + static struct i2c_driver w83l785ts_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "w83l785ts", }, - .attach_adapter = w83l785ts_attach_adapter, - .detach_client = w83l785ts_detach_client, + .probe = w83l785ts_probe, + .remove = w83l785ts_remove, + .id_table = w83l785ts_id, + .detect = w83l785ts_detect, + .address_data = &addr_data, }; /* @@ -105,7 +116,6 @@ static struct i2c_driver w83l785ts_driver = { */ struct w83l785ts_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* zero until following fields are valid */ @@ -135,40 +145,14 @@ static SENSOR_DEVICE_ATTR(temp1_max, S_IRUGO, show_temp, NULL, 1); * Real code */ -static int w83l785ts_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, w83l785ts_detect); -} - -/* - * The following function does more than just detection. If detection - * succeeds, it also registers the new chip. - */ -static int w83l785ts_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int w83l785ts_detect(struct i2c_client *new_client, int kind, + struct i2c_board_info *info) { - struct i2c_client *new_client; - struct w83l785ts_data *data; - int err = 0; - + struct i2c_adapter *adapter = new_client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct w83l785ts_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - /* The common I2C client data is placed right before the - * W83L785TS-specific data. */ - new_client = &data->client; - i2c_set_clientdata(new_client, data); - new_client->addr = address; - new_client->adapter = adapter; - new_client->driver = &w83l785ts_driver; - new_client->flags = 0; + return -ENODEV; /* * Now we do the remaining detection. A negative kind means that @@ -188,8 +172,8 @@ static int w83l785ts_detect(struct i2c_adapter *adapter, int address, int kind) W83L785TS_REG_TYPE, 0) & 0xFC) != 0x00)) { dev_dbg(&adapter->dev, "W83L785TS-S detection failed at 0x%02x.\n", - address); - goto exit_free; + new_client->addr); + return -ENODEV; } } @@ -214,22 +198,34 @@ static int w83l785ts_detect(struct i2c_adapter *adapter, int address, int kind) dev_info(&adapter->dev, "Unsupported chip (man_id=0x%04X, " "chip_id=0x%02X).\n", man_id, chip_id); - goto exit_free; + return -ENODEV; } } - /* We can fill in the remaining client fields. */ - strlcpy(new_client->name, "w83l785ts", I2C_NAME_SIZE); + strlcpy(info->type, "w83l785ts", I2C_NAME_SIZE); + + return 0; +} + +static int w83l785ts_probe(struct i2c_client *new_client, + const struct i2c_device_id *id) +{ + struct w83l785ts_data *data; + int err = 0; + + data = kzalloc(sizeof(struct w83l785ts_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(new_client, data); data->valid = 0; mutex_init(&data->update_lock); /* Default values in case the first read fails (unlikely). */ data->temp[1] = data->temp[0] = 0; - /* Tell the I2C layer a new client has arrived. */ - if ((err = i2c_attach_client(new_client))) - goto exit_free; - /* * Initialize the W83L785TS chip * Nothing yet, assume it is already started. @@ -259,25 +255,20 @@ exit_remove: &sensor_dev_attr_temp1_input.dev_attr); device_remove_file(&new_client->dev, &sensor_dev_attr_temp1_max.dev_attr); - i2c_detach_client(new_client); -exit_free: kfree(data); exit: return err; } -static int w83l785ts_detach_client(struct i2c_client *client) +static int w83l785ts_remove(struct i2c_client *client) { struct w83l785ts_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); device_remove_file(&client->dev, &sensor_dev_attr_temp1_input.dev_attr); device_remove_file(&client->dev, &sensor_dev_attr_temp1_max.dev_attr); - if ((err = i2c_detach_client(client))) - return err; kfree(data); return 0; @@ -286,6 +277,18 @@ static int w83l785ts_detach_client(struct i2c_client *client) static u8 w83l785ts_read_value(struct i2c_client *client, u8 reg, u8 defval) { int value, i; + struct device *dev; + const char *prefix; + + /* We might be called during detection, at which point the client + isn't yet fully initialized, so we can't use dev_dbg on it */ + if (i2c_get_clientdata(client)) { + dev = &client->dev; + prefix = ""; + } else { + dev = &client->adapter->dev; + prefix = "w83l785ts: "; + } /* Frequent read errors have been reported on Asus boards, so we * retry on read errors. If it still fails (unlikely), return the @@ -293,15 +296,15 @@ static u8 w83l785ts_read_value(struct i2c_client *client, u8 reg, u8 defval) for (i = 1; i <= MAX_RETRIES; i++) { value = i2c_smbus_read_byte_data(client, reg); if (value >= 0) { - dev_dbg(&client->dev, "Read 0x%02x from register " - "0x%02x.\n", value, reg); + dev_dbg(dev, "%sRead 0x%02x from register 0x%02x.\n", + prefix, value, reg); return value; } - dev_dbg(&client->dev, "Read failed, will retry in %d.\n", i); + dev_dbg(dev, "%sRead failed, will retry in %d.\n", prefix, i); msleep(i); } - dev_err(&client->dev, "Couldn't read value from register 0x%02x.\n", + dev_err(dev, "%sCouldn't read value from register 0x%02x.\n", prefix, reg); return defval; } diff --git a/drivers/hwmon/w83l786ng.c b/drivers/hwmon/w83l786ng.c index 41e22ddb568..badca769f35 100644 --- a/drivers/hwmon/w83l786ng.c +++ b/drivers/hwmon/w83l786ng.c @@ -121,7 +121,6 @@ DIV_TO_REG(long val) } struct w83l786ng_data { - struct i2c_client client; struct device *hwmon_dev; struct mutex update_lock; char valid; /* !=0 if following fields are valid */ @@ -146,18 +145,30 @@ struct w83l786ng_data { u8 tolerance[2]; }; -static int w83l786ng_attach_adapter(struct i2c_adapter *adapter); -static int w83l786ng_detect(struct i2c_adapter *adapter, int address, int kind); -static int w83l786ng_detach_client(struct i2c_client *client); +static int w83l786ng_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int w83l786ng_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int w83l786ng_remove(struct i2c_client *client); static void w83l786ng_init_client(struct i2c_client *client); static struct w83l786ng_data *w83l786ng_update_device(struct device *dev); +static const struct i2c_device_id w83l786ng_id[] = { + { "w83l786ng", w83l786ng }, + { } +}; +MODULE_DEVICE_TABLE(i2c, w83l786ng_id); + static struct i2c_driver w83l786ng_driver = { + .class = I2C_CLASS_HWMON, .driver = { .name = "w83l786ng", }, - .attach_adapter = w83l786ng_attach_adapter, - .detach_client = w83l786ng_detach_client, + .probe = w83l786ng_probe, + .remove = w83l786ng_remove, + .id_table = w83l786ng_id, + .detect = w83l786ng_detect, + .address_data = &addr_data, }; static u8 @@ -575,42 +586,15 @@ static const struct attribute_group w83l786ng_group = { }; static int -w83l786ng_attach_adapter(struct i2c_adapter *adapter) +w83l786ng_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, w83l786ng_detect); -} - -static int -w83l786ng_detect(struct i2c_adapter *adapter, int address, int kind) -{ - struct i2c_client *client; - struct device *dev; - struct w83l786ng_data *data; - int i, err = 0; - u8 reg_tmp; + struct i2c_adapter *adapter = client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { - goto exit; - } - - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. - But it allows us to access w83l786ng_{read,write}_value. */ - - if (!(data = kzalloc(sizeof(struct w83l786ng_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; + return -ENODEV; } - client = &data->client; - dev = &client->dev; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &w83l786ng_driver; - /* * Now we do the remaining detection. A negative kind means that * the driver was loaded with no force parameter (default), so we @@ -627,8 +611,8 @@ w83l786ng_detect(struct i2c_adapter *adapter, int address, int kind) W83L786NG_REG_CONFIG) & 0x80) != 0x00)) { dev_dbg(&adapter->dev, "W83L786NG detection failed at 0x%02x.\n", - address); - goto exit_free; + client->addr); + return -ENODEV; } } @@ -651,17 +635,31 @@ w83l786ng_detect(struct i2c_adapter *adapter, int address, int kind) dev_info(&adapter->dev, "Unsupported chip (man_id=0x%04X, " "chip_id=0x%02X).\n", man_id, chip_id); - goto exit_free; + return -ENODEV; } } - /* Fill in the remaining client fields and put into the global list */ - strlcpy(client->name, "w83l786ng", I2C_NAME_SIZE); - mutex_init(&data->update_lock); + strlcpy(info->type, "w83l786ng", I2C_NAME_SIZE); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_free; + return 0; +} + +static int +w83l786ng_probe(struct i2c_client *client, const struct i2c_device_id *id) +{ + struct device *dev = &client->dev; + struct w83l786ng_data *data; + int i, err = 0; + u8 reg_tmp; + + data = kzalloc(sizeof(struct w83l786ng_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); /* Initialize the chip */ w83l786ng_init_client(client); @@ -693,25 +691,19 @@ w83l786ng_detect(struct i2c_adapter *adapter, int address, int kind) exit_remove: sysfs_remove_group(&client->dev.kobj, &w83l786ng_group); - i2c_detach_client(client); -exit_free: kfree(data); exit: return err; } static int -w83l786ng_detach_client(struct i2c_client *client) +w83l786ng_remove(struct i2c_client *client) { struct w83l786ng_data *data = i2c_get_clientdata(client); - int err; hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&client->dev.kobj, &w83l786ng_group); - if ((err = i2c_detach_client(client))) - return err; - kfree(data); return 0; diff --git a/drivers/i2c/busses/i2c-amd756-s4882.c b/drivers/i2c/busses/i2c-amd756-s4882.c index 2f150e33c74..72872d1e63e 100644 --- a/drivers/i2c/busses/i2c-amd756-s4882.c +++ b/drivers/i2c/busses/i2c-amd756-s4882.c @@ -155,6 +155,16 @@ static int __init amd756_s4882_init(void) int i, error; union i2c_smbus_data ioconfig; + /* Configure the PCA9556 multiplexer */ + ioconfig.byte = 0x00; /* All I/O to output mode */ + error = i2c_smbus_xfer(&amd756_smbus, 0x18, 0, I2C_SMBUS_WRITE, 0x03, + I2C_SMBUS_BYTE_DATA, &ioconfig); + if (error) { + dev_err(&amd756_smbus.dev, "PCA9556 configuration failed\n"); + error = -EIO; + goto ERROR0; + } + /* Unregister physical bus */ error = i2c_del_adapter(&amd756_smbus); if (error) { @@ -198,22 +208,11 @@ static int __init amd756_s4882_init(void) s4882_algo[3].smbus_xfer = amd756_access_virt3; s4882_algo[4].smbus_xfer = amd756_access_virt4; - /* Configure the PCA9556 multiplexer */ - ioconfig.byte = 0x00; /* All I/O to output mode */ - error = amd756_smbus.algo->smbus_xfer(&amd756_smbus, 0x18, 0, - I2C_SMBUS_WRITE, 0x03, - I2C_SMBUS_BYTE_DATA, &ioconfig); - if (error) { - dev_err(&amd756_smbus.dev, "PCA9556 configuration failed\n"); - error = -EIO; - goto ERROR3; - } - /* Register virtual adapters */ for (i = 0; i < 5; i++) { error = i2c_add_adapter(s4882_adapter+i); if (error) { - dev_err(&amd756_smbus.dev, + printk(KERN_ERR "i2c-amd756-s4882: " "Virtual adapter %d registration " "failed, module not inserted\n", i); for (i--; i >= 0; i--) @@ -252,8 +251,8 @@ static void __exit amd756_s4882_exit(void) /* Restore physical bus */ if (i2c_add_adapter(&amd756_smbus)) - dev_err(&amd756_smbus.dev, "Physical bus restoration " - "failed\n"); + printk(KERN_ERR "i2c-amd756-s4882: " + "Physical bus restoration failed\n"); } MODULE_AUTHOR("Jean Delvare <khali@linux-fr.org>"); diff --git a/drivers/i2c/busses/i2c-nforce2-s4985.c b/drivers/i2c/busses/i2c-nforce2-s4985.c index 6a8995dfd0b..d1a4cbcf2aa 100644 --- a/drivers/i2c/busses/i2c-nforce2-s4985.c +++ b/drivers/i2c/busses/i2c-nforce2-s4985.c @@ -150,6 +150,16 @@ static int __init nforce2_s4985_init(void) int i, error; union i2c_smbus_data ioconfig; + /* Configure the PCA9556 multiplexer */ + ioconfig.byte = 0x00; /* All I/O to output mode */ + error = i2c_smbus_xfer(nforce2_smbus, 0x18, 0, I2C_SMBUS_WRITE, 0x03, + I2C_SMBUS_BYTE_DATA, &ioconfig); + if (error) { + dev_err(&nforce2_smbus->dev, "PCA9556 configuration failed\n"); + error = -EIO; + goto ERROR0; + } + /* Unregister physical bus */ if (!nforce2_smbus) return -ENODEV; @@ -191,24 +201,13 @@ static int __init nforce2_s4985_init(void) s4985_algo[3].smbus_xfer = nforce2_access_virt3; s4985_algo[4].smbus_xfer = nforce2_access_virt4; - /* Configure the PCA9556 multiplexer */ - ioconfig.byte = 0x00; /* All I/O to output mode */ - error = nforce2_smbus->algo->smbus_xfer(nforce2_smbus, 0x18, 0, - I2C_SMBUS_WRITE, 0x03, - I2C_SMBUS_BYTE_DATA, &ioconfig); - if (error) { - dev_err(&nforce2_smbus->dev, "PCA9556 configuration failed\n"); - error = -EIO; - goto ERROR3; - } - /* Register virtual adapters */ for (i = 0; i < 5; i++) { error = i2c_add_adapter(s4985_adapter + i); if (error) { - dev_err(&nforce2_smbus->dev, - "Virtual adapter %d registration " - "failed, module not inserted\n", i); + printk(KERN_ERR "i2c-nforce2-s4985: " + "Virtual adapter %d registration " + "failed, module not inserted\n", i); for (i--; i >= 0; i--) i2c_del_adapter(s4985_adapter + i); goto ERROR3; @@ -245,8 +244,8 @@ static void __exit nforce2_s4985_exit(void) /* Restore physical bus */ if (i2c_add_adapter(nforce2_smbus)) - dev_err(&nforce2_smbus->dev, "Physical bus restoration " - "failed\n"); + printk(KERN_ERR "i2c-nforce2-s4985: " + "Physical bus restoration failed\n"); } MODULE_AUTHOR("Jean Delvare <khali@linux-fr.org>"); diff --git a/drivers/i2c/chips/eeprom.c b/drivers/i2c/chips/eeprom.c index 373ea8d8fe8..2c27193aeaa 100644 --- a/drivers/i2c/chips/eeprom.c +++ b/drivers/i2c/chips/eeprom.c @@ -47,7 +47,6 @@ enum eeprom_nature { /* Each client has this additional data */ struct eeprom_data { - struct i2c_client client; struct mutex update_lock; u8 valid; /* bitfield, bit!=0 if slice is valid */ unsigned long last_updated[8]; /* In jiffies, 8 slices */ @@ -56,19 +55,6 @@ struct eeprom_data { }; -static int eeprom_attach_adapter(struct i2c_adapter *adapter); -static int eeprom_detect(struct i2c_adapter *adapter, int address, int kind); -static int eeprom_detach_client(struct i2c_client *client); - -/* This is the driver that will be inserted */ -static struct i2c_driver eeprom_driver = { - .driver = { - .name = "eeprom", - }, - .attach_adapter = eeprom_attach_adapter, - .detach_client = eeprom_detach_client, -}; - static void eeprom_update_client(struct i2c_client *client, u8 slice) { struct eeprom_data *data = i2c_get_clientdata(client); @@ -148,25 +134,17 @@ static struct bin_attribute eeprom_attr = { .read = eeprom_read, }; -static int eeprom_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & (I2C_CLASS_DDC | I2C_CLASS_SPD))) - return 0; - return i2c_probe(adapter, &addr_data, eeprom_detect); -} - -/* This function is called by i2c_probe */ -static int eeprom_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int eeprom_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - struct i2c_client *client; - struct eeprom_data *data; - int err = 0; + struct i2c_adapter *adapter = client->adapter; /* EDID EEPROMs are often 24C00 EEPROMs, which answer to all addresses 0x50-0x57, but we only care about 0x50. So decline attaching to addresses >= 0x51 on DDC buses */ - if (!(adapter->class & I2C_CLASS_SPD) && address >= 0x51) - goto exit; + if (!(adapter->class & I2C_CLASS_SPD) && client->addr >= 0x51) + return -ENODEV; /* There are four ways we can read the EEPROM data: (1) I2C block reads (faster, but unsupported by most adapters) @@ -177,32 +155,33 @@ static int eeprom_detect(struct i2c_adapter *adapter, int address, int kind) because all known adapters support one of the first two. */ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_WORD_DATA) && !i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_I2C_BLOCK)) - goto exit; + return -ENODEV; + + strlcpy(info->type, "eeprom", I2C_NAME_SIZE); + + return 0; +} + +static int eeprom_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct i2c_adapter *adapter = client->adapter; + struct eeprom_data *data; + int err; if (!(data = kzalloc(sizeof(struct eeprom_data), GFP_KERNEL))) { err = -ENOMEM; goto exit; } - client = &data->client; memset(data->data, 0xff, EEPROM_SIZE); i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &eeprom_driver; - - /* Fill in the remaining client fields */ - strlcpy(client->name, "eeprom", I2C_NAME_SIZE); mutex_init(&data->update_lock); data->nature = UNKNOWN; - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_kfree; - /* Detect the Vaio nature of EEPROMs. We use the "PCG-" or "VGN-" prefix as the signature. */ - if (address == 0x57 + if (client->addr == 0x57 && i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_BYTE_DATA)) { char name[4]; @@ -221,33 +200,42 @@ static int eeprom_detect(struct i2c_adapter *adapter, int address, int kind) /* create the sysfs eeprom file */ err = sysfs_create_bin_file(&client->dev.kobj, &eeprom_attr); if (err) - goto exit_detach; + goto exit_kfree; return 0; -exit_detach: - i2c_detach_client(client); exit_kfree: kfree(data); exit: return err; } -static int eeprom_detach_client(struct i2c_client *client) +static int eeprom_remove(struct i2c_client *client) { - int err; - sysfs_remove_bin_file(&client->dev.kobj, &eeprom_attr); - - err = i2c_detach_client(client); - if (err) - return err; - kfree(i2c_get_clientdata(client)); return 0; } +static const struct i2c_device_id eeprom_id[] = { + { "eeprom", 0 }, + { } +}; + +static struct i2c_driver eeprom_driver = { + .driver = { + .name = "eeprom", + }, + .probe = eeprom_probe, + .remove = eeprom_remove, + .id_table = eeprom_id, + + .class = I2C_CLASS_DDC | I2C_CLASS_SPD, + .detect = eeprom_detect, + .address_data = &addr_data, +}; + static int __init eeprom_init(void) { return i2c_add_driver(&eeprom_driver); diff --git a/drivers/i2c/chips/max6875.c b/drivers/i2c/chips/max6875.c index 5a0285d8b6f..033d9d81ec8 100644 --- a/drivers/i2c/chips/max6875.c +++ b/drivers/i2c/chips/max6875.c @@ -53,7 +53,7 @@ I2C_CLIENT_INSMOD_1(max6875); /* Each client has this additional data */ struct max6875_data { - struct i2c_client client; + struct i2c_client *fake_client; struct mutex update_lock; u32 valid; @@ -61,19 +61,6 @@ struct max6875_data { unsigned long last_updated[USER_EEPROM_SLICES]; }; -static int max6875_attach_adapter(struct i2c_adapter *adapter); -static int max6875_detect(struct i2c_adapter *adapter, int address, int kind); -static int max6875_detach_client(struct i2c_client *client); - -/* This is the driver that will be inserted */ -static struct i2c_driver max6875_driver = { - .driver = { - .name = "max6875", - }, - .attach_adapter = max6875_attach_adapter, - .detach_client = max6875_detach_client, -}; - static void max6875_update_slice(struct i2c_client *client, int slice) { struct max6875_data *data = i2c_get_clientdata(client); @@ -159,96 +146,87 @@ static struct bin_attribute user_eeprom_attr = { .read = max6875_read, }; -static int max6875_attach_adapter(struct i2c_adapter *adapter) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int max6875_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - return i2c_probe(adapter, &addr_data, max6875_detect); -} - -/* This function is called by i2c_probe */ -static int max6875_detect(struct i2c_adapter *adapter, int address, int kind) -{ - struct i2c_client *real_client; - struct i2c_client *fake_client; - struct max6875_data *data; - int err; + struct i2c_adapter *adapter = client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WRITE_BYTE_DATA | I2C_FUNC_SMBUS_READ_BYTE)) - return 0; + return -ENODEV; /* Only check even addresses */ - if (address & 1) - return 0; + if (client->addr & 1) + return -ENODEV; + + strlcpy(info->type, "max6875", I2C_NAME_SIZE); + + return 0; +} + +static int max6875_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct max6875_data *data; + int err; if (!(data = kzalloc(sizeof(struct max6875_data), GFP_KERNEL))) return -ENOMEM; /* A fake client is created on the odd address */ - if (!(fake_client = kzalloc(sizeof(struct i2c_client), GFP_KERNEL))) { + data->fake_client = i2c_new_dummy(client->adapter, client->addr + 1); + if (!data->fake_client) { err = -ENOMEM; - goto exit_kfree1; + goto exit_kfree; } /* Init real i2c_client */ - real_client = &data->client; - i2c_set_clientdata(real_client, data); - real_client->addr = address; - real_client->adapter = adapter; - real_client->driver = &max6875_driver; - strlcpy(real_client->name, "max6875", I2C_NAME_SIZE); + i2c_set_clientdata(client, data); mutex_init(&data->update_lock); - /* Init fake client data */ - i2c_set_clientdata(fake_client, NULL); - fake_client->addr = address | 1; - fake_client->adapter = adapter; - fake_client->driver = &max6875_driver; - strlcpy(fake_client->name, "max6875 subclient", I2C_NAME_SIZE); - - if ((err = i2c_attach_client(real_client)) != 0) - goto exit_kfree2; - - if ((err = i2c_attach_client(fake_client)) != 0) - goto exit_detach1; - - err = sysfs_create_bin_file(&real_client->dev.kobj, &user_eeprom_attr); + err = sysfs_create_bin_file(&client->dev.kobj, &user_eeprom_attr); if (err) - goto exit_detach2; + goto exit_remove_fake; return 0; -exit_detach2: - i2c_detach_client(fake_client); -exit_detach1: - i2c_detach_client(real_client); -exit_kfree2: - kfree(fake_client); -exit_kfree1: +exit_remove_fake: + i2c_unregister_device(data->fake_client); +exit_kfree: kfree(data); return err; } -/* Will be called for both the real client and the fake client */ -static int max6875_detach_client(struct i2c_client *client) +static int max6875_remove(struct i2c_client *client) { - int err; struct max6875_data *data = i2c_get_clientdata(client); - /* data is NULL for the fake client */ - if (data) - sysfs_remove_bin_file(&client->dev.kobj, &user_eeprom_attr); + i2c_unregister_device(data->fake_client); - err = i2c_detach_client(client); - if (err) - return err; + sysfs_remove_bin_file(&client->dev.kobj, &user_eeprom_attr); + kfree(data); - if (data) /* real client */ - kfree(data); - else /* fake client */ - kfree(client); return 0; } +static const struct i2c_device_id max6875_id[] = { + { "max6875", 0 }, + { } +}; + +static struct i2c_driver max6875_driver = { + .driver = { + .name = "max6875", + }, + .probe = max6875_probe, + .remove = max6875_remove, + .id_table = max6875_id, + + .detect = max6875_detect, + .address_data = &addr_data, +}; + static int __init max6875_init(void) { return i2c_add_driver(&max6875_driver); diff --git a/drivers/i2c/chips/pca9539.c b/drivers/i2c/chips/pca9539.c index 58ab7f26be2..270de4e56a8 100644 --- a/drivers/i2c/chips/pca9539.c +++ b/drivers/i2c/chips/pca9539.c @@ -14,8 +14,8 @@ #include <linux/i2c.h> #include <linux/hwmon-sysfs.h> -/* Addresses to scan */ -static unsigned short normal_i2c[] = {0x74, 0x75, 0x76, 0x77, I2C_CLIENT_END}; +/* Addresses to scan: none, device is not autodetected */ +static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(pca9539); @@ -32,23 +32,6 @@ enum pca9539_cmd PCA9539_DIRECTION_1 = 7, }; -static int pca9539_attach_adapter(struct i2c_adapter *adapter); -static int pca9539_detect(struct i2c_adapter *adapter, int address, int kind); -static int pca9539_detach_client(struct i2c_client *client); - -/* This is the driver that will be inserted */ -static struct i2c_driver pca9539_driver = { - .driver = { - .name = "pca9539", - }, - .attach_adapter = pca9539_attach_adapter, - .detach_client = pca9539_detach_client, -}; - -struct pca9539_data { - struct i2c_client client; -}; - /* following are the sysfs callback functions */ static ssize_t pca9539_show(struct device *dev, struct device_attribute *attr, char *buf) @@ -105,77 +88,51 @@ static struct attribute_group pca9539_defattr_group = { .attrs = pca9539_attributes, }; -static int pca9539_attach_adapter(struct i2c_adapter *adapter) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int pca9539_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - return i2c_probe(adapter, &addr_data, pca9539_detect); -} - -/* This function is called by i2c_probe */ -static int pca9539_detect(struct i2c_adapter *adapter, int address, int kind) -{ - struct i2c_client *client; - struct pca9539_data *data; - int err = 0; + struct i2c_adapter *adapter = client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. */ - if (!(data = kzalloc(sizeof(struct pca9539_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &pca9539_driver; - - if (kind < 0) { - /* Detection: the pca9539 only has 8 registers (0-7). - A read of 7 should succeed, but a read of 8 should fail. */ - if ((i2c_smbus_read_byte_data(client, 7) < 0) || - (i2c_smbus_read_byte_data(client, 8) >= 0)) - goto exit_kfree; - } - - strlcpy(client->name, "pca9539", I2C_NAME_SIZE); - - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_kfree; + return -ENODEV; - /* Register sysfs hooks */ - err = sysfs_create_group(&client->dev.kobj, - &pca9539_defattr_group); - if (err) - goto exit_detach; + strlcpy(info->type, "pca9539", I2C_NAME_SIZE); return 0; - -exit_detach: - i2c_detach_client(client); -exit_kfree: - kfree(data); -exit: - return err; } -static int pca9539_detach_client(struct i2c_client *client) +static int pca9539_probe(struct i2c_client *client, + const struct i2c_device_id *id) { - int err; + /* Register sysfs hooks */ + return sysfs_create_group(&client->dev.kobj, + &pca9539_defattr_group); +} +static int pca9539_remove(struct i2c_client *client) +{ sysfs_remove_group(&client->dev.kobj, &pca9539_defattr_group); - - if ((err = i2c_detach_client(client))) - return err; - - kfree(i2c_get_clientdata(client)); return 0; } +static const struct i2c_device_id pca9539_id[] = { + { "pca9539", 0 }, + { } +}; + +static struct i2c_driver pca9539_driver = { + .driver = { + .name = "pca9539", + }, + .probe = pca9539_probe, + .remove = pca9539_remove, + .id_table = pca9539_id, + + .detect = pca9539_detect, + .address_data = &addr_data, +}; + static int __init pca9539_init(void) { return i2c_add_driver(&pca9539_driver); diff --git a/drivers/i2c/chips/pcf8574.c b/drivers/i2c/chips/pcf8574.c index 1b3db2b3ada..6ec309894c8 100644 --- a/drivers/i2c/chips/pcf8574.c +++ b/drivers/i2c/chips/pcf8574.c @@ -38,37 +38,19 @@ #include <linux/slab.h> #include <linux/i2c.h> -/* Addresses to scan */ -static const unsigned short normal_i2c[] = { - 0x20, 0x21, 0x22, 0x23, 0x24, 0x25, 0x26, 0x27, - 0x38, 0x39, 0x3a, 0x3b, 0x3c, 0x3d, 0x3e, 0x3f, - I2C_CLIENT_END -}; +/* Addresses to scan: none, device can't be detected */ +static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_2(pcf8574, pcf8574a); /* Each client has this additional data */ struct pcf8574_data { - struct i2c_client client; - int write; /* Remember last written value */ }; -static int pcf8574_attach_adapter(struct i2c_adapter *adapter); -static int pcf8574_detect(struct i2c_adapter *adapter, int address, int kind); -static int pcf8574_detach_client(struct i2c_client *client); static void pcf8574_init_client(struct i2c_client *client); -/* This is the driver that will be inserted */ -static struct i2c_driver pcf8574_driver = { - .driver = { - .name = "pcf8574", - }, - .attach_adapter = pcf8574_attach_adapter, - .detach_client = pcf8574_detach_client, -}; - /* following are the sysfs callback functions */ static ssize_t show_read(struct device *dev, struct device_attribute *attr, char *buf) { @@ -119,41 +101,22 @@ static const struct attribute_group pcf8574_attr_group = { * Real code */ -static int pcf8574_attach_adapter(struct i2c_adapter *adapter) -{ - return i2c_probe(adapter, &addr_data, pcf8574_detect); -} - -/* This function is called by i2c_probe */ -static int pcf8574_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int pcf8574_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - struct i2c_client *client; - struct pcf8574_data *data; - int err = 0; - const char *client_name = ""; + struct i2c_adapter *adapter = client->adapter; + const char *client_name; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE)) - goto exit; - - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. */ - if (!(data = kzalloc(sizeof(struct pcf8574_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - client = &data->client; - i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &pcf8574_driver; + return -ENODEV; /* Now, we would do the remaining detection. But the PCF8574 is plainly impossible to detect! Stupid chip. */ /* Determine the chip type */ if (kind <= 0) { - if (address >= 0x38 && address <= 0x3f) + if (client->addr >= 0x38 && client->addr <= 0x3f) kind = pcf8574a; else kind = pcf8574; @@ -163,40 +126,43 @@ static int pcf8574_detect(struct i2c_adapter *adapter, int address, int kind) client_name = "pcf8574a"; else client_name = "pcf8574"; + strlcpy(info->type, client_name, I2C_NAME_SIZE); - /* Fill in the remaining client fields and put it into the global list */ - strlcpy(client->name, client_name, I2C_NAME_SIZE); + return 0; +} + +static int pcf8574_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct pcf8574_data *data; + int err; + + data = kzalloc(sizeof(struct pcf8574_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_free; - /* Initialize the PCF8574 chip */ pcf8574_init_client(client); /* Register sysfs hooks */ err = sysfs_create_group(&client->dev.kobj, &pcf8574_attr_group); if (err) - goto exit_detach; + goto exit_free; return 0; - exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: return err; } -static int pcf8574_detach_client(struct i2c_client *client) +static int pcf8574_remove(struct i2c_client *client) { - int err; - sysfs_remove_group(&client->dev.kobj, &pcf8574_attr_group); - - if ((err = i2c_detach_client(client))) - return err; - kfree(i2c_get_clientdata(client)); return 0; } @@ -208,6 +174,24 @@ static void pcf8574_init_client(struct i2c_client *client) data->write = -EAGAIN; } +static const struct i2c_device_id pcf8574_id[] = { + { "pcf8574", 0 }, + { "pcf8574a", 0 }, + { } +}; + +static struct i2c_driver pcf8574_driver = { + .driver = { + .name = "pcf8574", + }, + .probe = pcf8574_probe, + .remove = pcf8574_remove, + .id_table = pcf8574_id, + + .detect = pcf8574_detect, + .address_data = &addr_data, +}; + static int __init pcf8574_init(void) { return i2c_add_driver(&pcf8574_driver); diff --git a/drivers/i2c/chips/pcf8575.c b/drivers/i2c/chips/pcf8575.c index 3ea08ac0bfa..07fd7cb3c57 100644 --- a/drivers/i2c/chips/pcf8575.c +++ b/drivers/i2c/chips/pcf8575.c @@ -32,11 +32,8 @@ #include <linux/slab.h> /* kzalloc() */ #include <linux/sysfs.h> /* sysfs_create_group() */ -/* Addresses to scan */ -static const unsigned short normal_i2c[] = { - 0x20, 0x21, 0x22, 0x23, 0x24, 0x25, 0x26, 0x27, - I2C_CLIENT_END -}; +/* Addresses to scan: none, device can't be detected */ +static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD; @@ -44,24 +41,9 @@ I2C_CLIENT_INSMOD; /* Each client has this additional data */ struct pcf8575_data { - struct i2c_client client; int write; /* last written value, or error code */ }; -static int pcf8575_attach_adapter(struct i2c_adapter *adapter); -static int pcf8575_detect(struct i2c_adapter *adapter, int address, int kind); -static int pcf8575_detach_client(struct i2c_client *client); - -/* This is the driver that will be inserted */ -static struct i2c_driver pcf8575_driver = { - .driver = { - .owner = THIS_MODULE, - .name = "pcf8575", - }, - .attach_adapter = pcf8575_attach_adapter, - .detach_client = pcf8575_detach_client, -}; - /* following are the sysfs callback functions */ static ssize_t show_read(struct device *dev, struct device_attribute *attr, char *buf) @@ -126,75 +108,77 @@ static const struct attribute_group pcf8575_attr_group = { * Real code */ -static int pcf8575_attach_adapter(struct i2c_adapter *adapter) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int pcf8575_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - return i2c_probe(adapter, &addr_data, pcf8575_detect); + struct i2c_adapter *adapter = client->adapter; + + if (!i2c_check_functionality(adapter, I2C_FUNC_I2C)) + return -ENODEV; + + /* This is the place to detect whether the chip at the specified + address really is a PCF8575 chip. However, there is no method known + to detect whether an I2C chip is a PCF8575 or any other I2C chip. */ + + strlcpy(info->type, "pcf8575", I2C_NAME_SIZE); + + return 0; } -/* This function is called by i2c_probe */ -static int pcf8575_detect(struct i2c_adapter *adapter, int address, int kind) +static int pcf8575_probe(struct i2c_client *client, + const struct i2c_device_id *id) { - struct i2c_client *client; struct pcf8575_data *data; - int err = 0; - - if (!i2c_check_functionality(adapter, I2C_FUNC_I2C)) - goto exit; + int err; - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. */ data = kzalloc(sizeof(struct pcf8575_data), GFP_KERNEL); if (!data) { err = -ENOMEM; goto exit; } - client = &data->client; i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &pcf8575_driver; - strlcpy(client->name, "pcf8575", I2C_NAME_SIZE); data->write = -EAGAIN; - /* This is the place to detect whether the chip at the specified - address really is a PCF8575 chip. However, there is no method known - to detect whether an I2C chip is a PCF8575 or any other I2C chip. */ - - /* Tell the I2C layer a new client has arrived */ - err = i2c_attach_client(client); - if (err) - goto exit_free; - /* Register sysfs hooks */ err = sysfs_create_group(&client->dev.kobj, &pcf8575_attr_group); if (err) - goto exit_detach; + goto exit_free; return 0; -exit_detach: - i2c_detach_client(client); exit_free: kfree(data); exit: return err; } -static int pcf8575_detach_client(struct i2c_client *client) +static int pcf8575_remove(struct i2c_client *client) { - int err; - sysfs_remove_group(&client->dev.kobj, &pcf8575_attr_group); - - err = i2c_detach_client(client); - if (err) - return err; - kfree(i2c_get_clientdata(client)); return 0; } +static const struct i2c_device_id pcf8575_id[] = { + { "pcf8575", 0 }, + { } +}; + +static struct i2c_driver pcf8575_driver = { + .driver = { + .owner = THIS_MODULE, + .name = "pcf8575", + }, + .probe = pcf8575_probe, + .remove = pcf8575_remove, + .id_table = pcf8575_id, + + .detect = pcf8575_detect, + .address_data = &addr_data, +}; + static int __init pcf8575_init(void) { return i2c_add_driver(&pcf8575_driver); diff --git a/drivers/i2c/chips/pcf8591.c b/drivers/i2c/chips/pcf8591.c index db735379f22..16ce3e19377 100644 --- a/drivers/i2c/chips/pcf8591.c +++ b/drivers/i2c/chips/pcf8591.c @@ -72,28 +72,15 @@ MODULE_PARM_DESC(input_mode, #define REG_TO_SIGNED(reg) (((reg) & 0x80)?((reg) - 256):(reg)) struct pcf8591_data { - struct i2c_client client; struct mutex update_lock; u8 control; u8 aout; }; -static int pcf8591_attach_adapter(struct i2c_adapter *adapter); -static int pcf8591_detect(struct i2c_adapter *adapter, int address, int kind); -static int pcf8591_detach_client(struct i2c_client *client); static void pcf8591_init_client(struct i2c_client *client); static int pcf8591_read_channel(struct device *dev, int channel); -/* This is the driver that will be inserted */ -static struct i2c_driver pcf8591_driver = { - .driver = { - .name = "pcf8591", - }, - .attach_adapter = pcf8591_attach_adapter, - .detach_client = pcf8591_detach_client, -}; - /* following are the sysfs callback functions */ #define show_in_channel(channel) \ static ssize_t show_in##channel##_input(struct device *dev, struct device_attribute *attr, char *buf) \ @@ -180,58 +167,46 @@ static const struct attribute_group pcf8591_attr_group_opt = { /* * Real code */ -static int pcf8591_attach_adapter(struct i2c_adapter *adapter) -{ - return i2c_probe(adapter, &addr_data, pcf8591_detect); -} -/* This function is called by i2c_probe */ -static int pcf8591_detect(struct i2c_adapter *adapter, int address, int kind) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int pcf8591_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - struct i2c_client *client; - struct pcf8591_data *data; - int err = 0; + struct i2c_adapter *adapter = client->adapter; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE | I2C_FUNC_SMBUS_WRITE_BYTE_DATA)) - goto exit; + return -ENODEV; + + /* Now, we would do the remaining detection. But the PCF8591 is plainly + impossible to detect! Stupid chip. */ + + strlcpy(info->type, "pcf8591", I2C_NAME_SIZE); + + return 0; +} + +static int pcf8591_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct pcf8591_data *data; + int err; - /* OK. For now, we presume we have a valid client. We now create the - client structure, even though we cannot fill it completely yet. */ if (!(data = kzalloc(sizeof(struct pcf8591_data), GFP_KERNEL))) { err = -ENOMEM; goto exit; } - client = &data->client; i2c_set_clientdata(client, data); - client->addr = address; - client->adapter = adapter; - client->driver = &pcf8591_driver; - - /* Now, we would do the remaining detection. But the PCF8591 is plainly - impossible to detect! Stupid chip. */ - - /* Determine the chip type - only one kind supported! */ - if (kind <= 0) - kind = pcf8591; - - /* Fill in the remaining client fields and put it into the global - list */ - strlcpy(client->name, "pcf8591", I2C_NAME_SIZE); mutex_init(&data->update_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(client))) - goto exit_kfree; - /* Initialize the PCF8591 chip */ pcf8591_init_client(client); /* Register sysfs hooks */ err = sysfs_create_group(&client->dev.kobj, &pcf8591_attr_group); if (err) - goto exit_detach; + goto exit_kfree; /* Register input2 if not in "two differential inputs" mode */ if (input_mode != 3) { @@ -252,24 +227,16 @@ static int pcf8591_detect(struct i2c_adapter *adapter, int address, int kind) exit_sysfs_remove: sysfs_remove_group(&client->dev.kobj, &pcf8591_attr_group_opt); sysfs_remove_group(&client->dev.kobj, &pcf8591_attr_group); -exit_detach: - i2c_detach_client(client); exit_kfree: kfree(data); exit: return err; } -static int pcf8591_detach_client(struct i2c_client *client) +static int pcf8591_remove(struct i2c_client *client) { - int err; - sysfs_remove_group(&client->dev.kobj, &pcf8591_attr_group_opt); sysfs_remove_group(&client->dev.kobj, &pcf8591_attr_group); - - if ((err = i2c_detach_client(client))) - return err; - kfree(i2c_get_clientdata(client)); return 0; } @@ -316,6 +283,25 @@ static int pcf8591_read_channel(struct device *dev, int channel) return (10 * value); } +static const struct i2c_device_id pcf8591_id[] = { + { "pcf8591", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, pcf8591_id); + +static struct i2c_driver pcf8591_driver = { + .driver = { + .name = "pcf8591", + }, + .probe = pcf8591_probe, + .remove = pcf8591_remove, + .id_table = pcf8591_id, + + .class = I2C_CLASS_HWMON, /* Nearest choice */ + .detect = pcf8591_detect, + .address_data = &addr_data, +}; + static int __init pcf8591_init(void) { if (input_mode < 0 || input_mode > 3) { diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c index 0a79f766101..7608df83d6d 100644 --- a/drivers/i2c/i2c-core.c +++ b/drivers/i2c/i2c-core.c @@ -654,6 +654,10 @@ int i2c_del_adapter(struct i2c_adapter *adap) dev_dbg(&adap->dev, "adapter [%s] unregistered\n", adap->name); + /* Clear the device structure in case this adapter is ever going to be + added again */ + memset(&adap->dev, 0, sizeof(adap->dev)); + out_unlock: mutex_unlock(&core_lock); return res; diff --git a/drivers/w1/masters/ds2482.c b/drivers/w1/masters/ds2482.c index 0fd5820d5c6..df52cb355f7 100644 --- a/drivers/w1/masters/ds2482.c +++ b/drivers/w1/masters/ds2482.c @@ -94,21 +94,31 @@ static const u8 ds2482_chan_rd[8] = #define DS2482_REG_STS_1WB 0x01 -static int ds2482_attach_adapter(struct i2c_adapter *adapter); -static int ds2482_detect(struct i2c_adapter *adapter, int address, int kind); -static int ds2482_detach_client(struct i2c_client *client); +static int ds2482_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int ds2482_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int ds2482_remove(struct i2c_client *client); /** * Driver data (common to all clients) */ +static const struct i2c_device_id ds2482_id[] = { + { "ds2482", 0 }, + { } +}; + static struct i2c_driver ds2482_driver = { .driver = { .owner = THIS_MODULE, .name = "ds2482", }, - .attach_adapter = ds2482_attach_adapter, - .detach_client = ds2482_detach_client, + .probe = ds2482_probe, + .remove = ds2482_remove, + .id_table = ds2482_id, + .detect = ds2482_detect, + .address_data = &addr_data, }; /* @@ -124,7 +134,7 @@ struct ds2482_w1_chan { }; struct ds2482_data { - struct i2c_client client; + struct i2c_client *client; struct mutex access_lock; /* 1-wire interface(s) */ @@ -147,7 +157,7 @@ struct ds2482_data { static inline int ds2482_select_register(struct ds2482_data *pdev, u8 read_ptr) { if (pdev->read_prt != read_ptr) { - if (i2c_smbus_write_byte_data(&pdev->client, + if (i2c_smbus_write_byte_data(pdev->client, DS2482_CMD_SET_READ_PTR, read_ptr) < 0) return -1; @@ -167,7 +177,7 @@ static inline int ds2482_select_register(struct ds2482_data *pdev, u8 read_ptr) */ static inline int ds2482_send_cmd(struct ds2482_data *pdev, u8 cmd) { - if (i2c_smbus_write_byte(&pdev->client, cmd) < 0) + if (i2c_smbus_write_byte(pdev->client, cmd) < 0) return -1; pdev->read_prt = DS2482_PTR_CODE_STATUS; @@ -187,7 +197,7 @@ static inline int ds2482_send_cmd(struct ds2482_data *pdev, u8 cmd) static inline int ds2482_send_cmd_data(struct ds2482_data *pdev, u8 cmd, u8 byte) { - if (i2c_smbus_write_byte_data(&pdev->client, cmd, byte) < 0) + if (i2c_smbus_write_byte_data(pdev->client, cmd, byte) < 0) return -1; /* all cmds leave in STATUS, except CONFIG */ @@ -216,7 +226,7 @@ static int ds2482_wait_1wire_idle(struct ds2482_data *pdev) if (!ds2482_select_register(pdev, DS2482_PTR_CODE_STATUS)) { do { - temp = i2c_smbus_read_byte(&pdev->client); + temp = i2c_smbus_read_byte(pdev->client); } while ((temp >= 0) && (temp & DS2482_REG_STS_1WB) && (++retries < DS2482_WAIT_IDLE_TIMEOUT)); } @@ -238,13 +248,13 @@ static int ds2482_wait_1wire_idle(struct ds2482_data *pdev) */ static int ds2482_set_channel(struct ds2482_data *pdev, u8 channel) { - if (i2c_smbus_write_byte_data(&pdev->client, DS2482_CMD_CHANNEL_SELECT, + if (i2c_smbus_write_byte_data(pdev->client, DS2482_CMD_CHANNEL_SELECT, ds2482_chan_wr[channel]) < 0) return -1; pdev->read_prt = DS2482_PTR_CODE_CHANNEL; pdev->channel = -1; - if (i2c_smbus_read_byte(&pdev->client) == ds2482_chan_rd[channel]) { + if (i2c_smbus_read_byte(pdev->client) == ds2482_chan_rd[channel]) { pdev->channel = channel; return 0; } @@ -368,7 +378,7 @@ static u8 ds2482_w1_read_byte(void *data) ds2482_select_register(pdev, DS2482_PTR_CODE_DATA); /* Read the data byte */ - result = i2c_smbus_read_byte(&pdev->client); + result = i2c_smbus_read_byte(pdev->client); mutex_unlock(&pdev->access_lock); @@ -415,47 +425,38 @@ static u8 ds2482_w1_reset_bus(void *data) } -/** - * Called to see if the device exists on an i2c bus. - */ -static int ds2482_attach_adapter(struct i2c_adapter *adapter) +static int ds2482_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) { - return i2c_probe(adapter, &addr_data, ds2482_detect); -} + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_WRITE_BYTE_DATA | + I2C_FUNC_SMBUS_BYTE)) + return -ENODEV; + strlcpy(info->type, "ds2482", I2C_NAME_SIZE); -/* - * The following function does more than just detection. If detection - * succeeds, it also registers the new chip. - */ -static int ds2482_detect(struct i2c_adapter *adapter, int address, int kind) + return 0; +} + +static int ds2482_probe(struct i2c_client *client, + const struct i2c_device_id *id) { struct ds2482_data *data; - struct i2c_client *new_client; - int err = 0; + int err = -ENODEV; int temp1; int idx; - if (!i2c_check_functionality(adapter, - I2C_FUNC_SMBUS_WRITE_BYTE_DATA | - I2C_FUNC_SMBUS_BYTE)) - goto exit; - if (!(data = kzalloc(sizeof(struct ds2482_data), GFP_KERNEL))) { err = -ENOMEM; goto exit; } - new_client = &data->client; - i2c_set_clientdata(new_client, data); - new_client->addr = address; - new_client->driver = &ds2482_driver; - new_client->adapter = adapter; + data->client = client; + i2c_set_clientdata(client, data); /* Reset the device (sets the read_ptr to status) */ if (ds2482_send_cmd(data, DS2482_CMD_RESET) < 0) { - dev_dbg(&adapter->dev, "DS2482 reset failed at 0x%02x.\n", - address); + dev_warn(&client->dev, "DS2482 reset failed.\n"); goto exit_free; } @@ -463,10 +464,10 @@ static int ds2482_detect(struct i2c_adapter *adapter, int address, int kind) ndelay(525); /* Read the status byte - only reset bit and line should be set */ - temp1 = i2c_smbus_read_byte(new_client); + temp1 = i2c_smbus_read_byte(client); if (temp1 != (DS2482_REG_STS_LL | DS2482_REG_STS_RST)) { - dev_dbg(&adapter->dev, "DS2482 (0x%02x) reset status " - "0x%02X - not a DS2482\n", address, temp1); + dev_warn(&client->dev, "DS2482 reset status " + "0x%02X - not a DS2482\n", temp1); goto exit_free; } @@ -478,16 +479,8 @@ static int ds2482_detect(struct i2c_adapter *adapter, int address, int kind) /* Set all config items to 0 (off) */ ds2482_send_cmd_data(data, DS2482_CMD_WRITE_CONFIG, 0xF0); - /* We can fill in the remaining client fields */ - snprintf(new_client->name, sizeof(new_client->name), "ds2482-%d00", - data->w1_count); - mutex_init(&data->access_lock); - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(new_client))) - goto exit_free; - /* Register 1-wire interface(s) */ for (idx = 0; idx < data->w1_count; idx++) { data->w1_ch[idx].pdev = data; @@ -511,8 +504,6 @@ static int ds2482_detect(struct i2c_adapter *adapter, int address, int kind) return 0; exit_w1_remove: - i2c_detach_client(new_client); - for (idx = 0; idx < data->w1_count; idx++) { if (data->w1_ch[idx].pdev != NULL) w1_remove_master_device(&data->w1_ch[idx].w1_bm); @@ -523,10 +514,10 @@ exit: return err; } -static int ds2482_detach_client(struct i2c_client *client) +static int ds2482_remove(struct i2c_client *client) { struct ds2482_data *data = i2c_get_clientdata(client); - int err, idx; + int idx; /* Unregister the 1-wire bridge(s) */ for (idx = 0; idx < data->w1_count; idx++) { @@ -534,13 +525,6 @@ static int ds2482_detach_client(struct i2c_client *client) w1_remove_master_device(&data->w1_ch[idx].w1_bm); } - /* Detach the i2c device */ - if ((err = i2c_detach_client(client))) { - dev_err(&client->dev, - "Deregistration failed, client not detached.\n"); - return err; - } - /* Free the memory */ kfree(data); return 0; |