diff options
36 files changed, 8524 insertions, 31 deletions
diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig index be54e36e8b6..19b43f37e1a 100644 --- a/arch/blackfin/Kconfig +++ b/arch/blackfin/Kconfig @@ -77,6 +77,26 @@ choice prompt "CPU" default BF533 +config BF512 + bool "BF512" + help + BF512 Processor Support. + +config BF514 + bool "BF514" + help + BF514 Processor Support. + +config BF516 + bool "BF516" + help + BF516 Processor Support. + +config BF518 + bool "BF518" + help + BF518 Processor Support. + config BF522 bool "BF522" help @@ -181,27 +201,27 @@ endchoice config BF_REV_MIN int - default 0 if (BF52x || BF54x) + default 0 if (BF51x || BF52x || BF54x) default 2 if (BF537 || BF536 || BF534) default 3 if (BF561 ||BF533 || BF532 || BF531) - default 4 if (BF538 || BF539) + default 4 if (BF538 || BF539) config BF_REV_MAX int - default 2 if (BF52x || BF54x) + default 2 if (BF51x || BF52x || BF54x) default 3 if (BF537 || BF536 || BF534) - default 5 if (BF561|| BF538 || BF539) + default 5 if (BF561 || BF538 || BF539) default 6 if (BF533 || BF532 || BF531) choice prompt "Silicon Rev" - default BF_REV_0_1 if (BF52x || BF54x) + default BF_REV_0_1 if (BF51x || BF52x || BF54x) default BF_REV_0_2 if (BF534 || BF536 || BF537) default BF_REV_0_3 if (BF531 || BF532 || BF533 || BF561) config BF_REV_0_0 bool "0.0" - depends on (BF52x || BF54x) + depends on (BF51x || BF52x || BF54x) config BF_REV_0_1 bool "0.1" @@ -235,6 +255,11 @@ config BF_REV_NONE endchoice +config BF51x + bool + depends on (BF512 || BF514 || BF516 || BF518) + default y + config BF52x bool depends on (BF522 || BF523 || BF524 || BF525 || BF526 || BF527) @@ -282,6 +307,7 @@ config MEM_MT48LC32M16A2TG_75 depends on (BFIN527_EZKIT || BFIN532_IP0X || BLACKSTAMP || BFIN526_EZBRD) default y +source "arch/blackfin/mach-bf518/Kconfig" source "arch/blackfin/mach-bf527/Kconfig" source "arch/blackfin/mach-bf533/Kconfig" source "arch/blackfin/mach-bf561/Kconfig" @@ -330,7 +356,7 @@ config CLKIN_HZ int "Frequency of the crystal on the board in Hz" default "11059200" if BFIN533_STAMP default "27000000" if BFIN533_EZKIT - default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN538_EZKIT) + default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN538_EZKIT || BFIN518F-EZBRD) default "30000000" if BFIN561_EZKIT default "24576000" if PNAV10 default "10000000" if BFIN532_IP0X @@ -370,7 +396,7 @@ config VCO_MULT default "22" if BFIN533_BLUETECHNIX_CM default "20" if (BFIN537_BLUETECHNIX_CM || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM) default "20" if BFIN561_EZKIT - default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD) + default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN518F_EZBRD) help This controls the frequency of the on-chip PLL. This can be between 1 and 64. PLL Frequency = (Crystal Frequency) * (this setting) @@ -432,6 +458,10 @@ config MAX_MEM_SIZE # config MAX_VCO_HZ int + default 400000000 if BF512 + default 400000000 if BF514 + default 400000000 if BF516 + default 400000000 if BF518 default 600000000 if BF522 default 400000000 if BF523 default 400000000 if BF524 @@ -1025,7 +1055,7 @@ comment "Possible Suspend Mem / Hibernate Wake-Up Sources" config PM_BFIN_WAKE_PH6 bool "Allow Wake-Up from on-chip PHY or PH6 GP" - depends on PM && (BF52x || BF534 || BF536 || BF537) + depends on PM && (BF51x || BF52x || BF534 || BF536 || BF537) default n help Enable PHY and PH6 GP Wake-Up (Voltage Regulator Power-Up) diff --git a/arch/blackfin/Makefile b/arch/blackfin/Makefile index ce45df3708e..2faad124db5 100644 --- a/arch/blackfin/Makefile +++ b/arch/blackfin/Makefile @@ -21,6 +21,10 @@ KALLSYMS += --symbol-prefix=_ KBUILD_DEFCONFIG := BF537-STAMP_defconfig # setup the machine name and the machine dependent settings +machine-$(CONFIG_BF512) := bf518 +machine-$(CONFIG_BF514) := bf518 +machine-$(CONFIG_BF516) := bf518 +machine-$(CONFIG_BF518) := bf518 machine-$(CONFIG_BF522) := bf527 machine-$(CONFIG_BF523) := bf527 machine-$(CONFIG_BF524) := bf527 @@ -44,6 +48,10 @@ machine-$(CONFIG_BF561) := bf561 MACHINE := $(machine-y) export MACHINE +cpu-$(CONFIG_BF512) := bf512 +cpu-$(CONFIG_BF514) := bf514 +cpu-$(CONFIG_BF516) := bf516 +cpu-$(CONFIG_BF518) := bf518 cpu-$(CONFIG_BF522) := bf522 cpu-$(CONFIG_BF523) := bf523 cpu-$(CONFIG_BF524) := bf524 diff --git a/arch/blackfin/configs/BF518F-EZBRD_defconfig b/arch/blackfin/configs/BF518F-EZBRD_defconfig new file mode 100644 index 00000000000..f4c4fd7d0e7 --- /dev/null +++ b/arch/blackfin/configs/BF518F-EZBRD_defconfig @@ -0,0 +1,1130 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.26.5 +# Thu Oct 23 21:38:19 2008 +# +# CONFIG_MMU is not set +# CONFIG_FPU is not set +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set +CONFIG_BLACKFIN=y +CONFIG_ZONE_DMA=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_GENERIC_GPIO=y +CONFIG_FORCE_MAX_ZONEORDER=14 +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set +# CONFIG_SYSFS_DEPRECATED is not set +# CONFIG_SYSFS_DEPRECATED_V2 is not set +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_HAVE_KPROBES is not set +# CONFIG_HAVE_KRETPROBES is not set +# CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +CONFIG_TINY_SHMEM=y +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +# CONFIG_IOSCHED_AS is not set +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +# CONFIG_DEFAULT_AS is not set +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +CONFIG_DEFAULT_NOOP=y +CONFIG_DEFAULT_IOSCHED="noop" +CONFIG_CLASSIC_RCU=y +# CONFIG_PREEMPT_NONE is not set +CONFIG_PREEMPT_VOLUNTARY=y +# CONFIG_PREEMPT is not set + +# +# Blackfin Processor Options +# + +# +# Processor and Board Settings +# +# CONFIG_BF512 is not set +# CONFIG_BF514 is not set +# CONFIG_BF516 is not set +CONFIG_BF518=y +# CONFIG_BF522 is not set +# CONFIG_BF523 is not set +# CONFIG_BF524 is not set +# CONFIG_BF525 is not set +# CONFIG_BF526 is not set +# CONFIG_BF527 is not set +# CONFIG_BF531 is not set +# CONFIG_BF532 is not set +# CONFIG_BF533 is not set +# CONFIG_BF534 is not set +# CONFIG_BF536 is not set +# CONFIG_BF537 is not set +# CONFIG_BF538 is not set +# CONFIG_BF539 is not set +# CONFIG_BF542 is not set +# CONFIG_BF544 is not set +# CONFIG_BF547 is not set +# CONFIG_BF548 is not set +# CONFIG_BF549 is not set +# CONFIG_BF561 is not set +CONFIG_BF_REV_MIN=0 +CONFIG_BF_REV_MAX=2 +CONFIG_BF_REV_0_0=y +# CONFIG_BF_REV_0_1 is not set +# CONFIG_BF_REV_0_2 is not set +# CONFIG_BF_REV_0_3 is not set +# CONFIG_BF_REV_0_4 is not set +# CONFIG_BF_REV_0_5 is not set +# CONFIG_BF_REV_0_6 is not set +# CONFIG_BF_REV_ANY is not set +# CONFIG_BF_REV_NONE is not set +CONFIG_BF51x=y +CONFIG_BFIN518F_EZBRD=y + +# +# BF518 Specific Configuration +# + +# +# Alternative Multiplexing Scheme +# +# CONFIG_BF518_SPORT0_PORTF is not set +CONFIG_BF518_SPORT0_PORTG=y +CONFIG_BF518_SPORT0_TSCLK_PG10=y +# CONFIG_BF518_SPORT0_TSCLK_PG14 is not set +CONFIG_BF518_UART1_PORTF=y +# CONFIG_BF518_UART1_PORTG is not set + +# +# Interrupt Priority Assignment +# + +# +# Priority +# +CONFIG_IRQ_PLL_WAKEUP=7 +CONFIG_IRQ_DMA0_ERROR=7 +CONFIG_IRQ_DMAR0_BLK=7 +CONFIG_IRQ_DMAR1_BLK=7 +CONFIG_IRQ_DMAR0_OVR=7 +CONFIG_IRQ_DMAR1_OVR=7 +CONFIG_IRQ_PPI_ERROR=7 +CONFIG_IRQ_MAC_ERROR=7 +CONFIG_IRQ_SPORT0_ERROR=7 +CONFIG_IRQ_SPORT1_ERROR=7 +CONFIG_IRQ_PTP_ERROR=7 +CONFIG_IRQ_UART0_ERROR=7 +CONFIG_IRQ_UART1_ERROR=7 +CONFIG_IRQ_RTC=8 +CONFIG_IRQ_PPI=8 +CONFIG_IRQ_SPORT0_RX=9 +CONFIG_IRQ_SPORT0_TX=9 +CONFIG_IRQ_SPORT1_RX=9 +CONFIG_IRQ_SPORT1_TX=9 +CONFIG_IRQ_TWI=10 +CONFIG_IRQ_SPI0=10 +CONFIG_IRQ_UART0_RX=10 +CONFIG_IRQ_UART0_TX=10 +CONFIG_IRQ_UART1_RX=10 +CONFIG_IRQ_UART1_TX=10 +CONFIG_IRQ_OPTSEC=11 +CONFIG_IRQ_CNT=11 +CONFIG_IRQ_MAC_RX=11 +CONFIG_IRQ_PORTH_INTA=11 +CONFIG_IRQ_MAC_TX=11 +CONFIG_IRQ_PORTH_INTB=11 +CONFIG_IRQ_TMR0=12 +CONFIG_IRQ_TMR1=12 +CONFIG_IRQ_TMR2=12 +CONFIG_IRQ_TMR3=12 +CONFIG_IRQ_TMR4=12 +CONFIG_IRQ_TMR5=12 +CONFIG_IRQ_TMR6=12 +CONFIG_IRQ_TMR7=12 +CONFIG_IRQ_PORTG_INTA=12 +CONFIG_IRQ_PORTG_INTB=12 +CONFIG_IRQ_MEM_DMA0=13 +CONFIG_IRQ_MEM_DMA1=13 +CONFIG_IRQ_WATCH=13 +CONFIG_IRQ_PORTF_INTA=13 +CONFIG_IRQ_PORTF_INTB=13 +CONFIG_IRQ_SPI0_ERROR=7 +CONFIG_IRQ_SPI1_ERROR=7 +CONFIG_IRQ_RSI_INT0=7 +CONFIG_IRQ_RSI_INT1=7 +CONFIG_IRQ_PWM_TRIP=10 +CONFIG_IRQ_PWM_SYNC=10 +CONFIG_IRQ_PTP_STAT=10 + +# +# Board customizations +# +# CONFIG_CMDLINE_BOOL is not set +CONFIG_BOOT_LOAD=0x1000 +CONFIG_ROM_BASE=0x20040000 + +# +# Clock/PLL Setup +# +CONFIG_CLKIN_HZ=25000000 +# CONFIG_BFIN_KERNEL_CLOCK is not set +CONFIG_MAX_MEM_SIZE=512 +CONFIG_MAX_VCO_HZ=400000000 +CONFIG_MIN_VCO_HZ=50000000 +CONFIG_MAX_SCLK_HZ=133333333 +CONFIG_MIN_SCLK_HZ=27000000 + +# +# Kernel Timer/Scheduler +# +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_300 is not set +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +# CONFIG_SCHED_HRTICK is not set +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +# CONFIG_CYCLES_CLOCKSOURCE is not set +# CONFIG_TICK_ONESHOT is not set +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y + +# +# Misc +# +CONFIG_BFIN_SCRATCH_REG_RETN=y +# CONFIG_BFIN_SCRATCH_REG_RETE is not set +# CONFIG_BFIN_SCRATCH_REG_CYCLES is not set + +# +# Blackfin Kernel Optimizations +# + +# +# Memory Optimizations +# +CONFIG_I_ENTRY_L1=y +CONFIG_EXCPT_IRQ_SYSC_L1=y +CONFIG_DO_IRQ_L1=y +CONFIG_CORE_TIMER_IRQ_L1=y +CONFIG_IDLE_L1=y +# CONFIG_SCHEDULE_L1 is not set +CONFIG_ARITHMETIC_OPS_L1=y +CONFIG_ACCESS_OK_L1=y +# CONFIG_MEMSET_L1 is not set +# CONFIG_MEMCPY_L1 is not set +# CONFIG_SYS_BFIN_SPINLOCK_L1 is not set +# CONFIG_IP_CHECKSUM_L1 is not set +CONFIG_CACHELINE_ALIGNED_L1=y +# CONFIG_SYSCALL_TAB_L1 is not set +# CONFIG_CPLB_SWITCH_TAB_L1 is not set +CONFIG_APP_STACK_L1=y + +# +# Speed Optimizations +# +CONFIG_BFIN_INS_LOWOVERHEAD=y +CONFIG_RAMKERNEL=y +# CONFIG_ROMKERNEL is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_VIRT_TO_BUS=y +CONFIG_BFIN_GPTIMERS=y +CONFIG_BFIN_DMA_5XX=y +# CONFIG_DMA_UNCACHED_4M is not set +# CONFIG_DMA_UNCACHED_2M is not set +CONFIG_DMA_UNCACHED_1M=y +# CONFIG_DMA_UNCACHED_NONE is not set + +# +# Cache Support +# +CONFIG_BFIN_ICACHE=y +CONFIG_BFIN_DCACHE=y +# CONFIG_BFIN_DCACHE_BANKA is not set +# CONFIG_BFIN_ICACHE_LOCK is not set +CONFIG_BFIN_WB=y +# CONFIG_BFIN_WT is not set +# CONFIG_MPU is not set + +# +# Asynchonous Memory Configuration +# + +# +# EBIU_AMGCTL Global Control +# +CONFIG_C_AMCKEN=y +CONFIG_C_CDPRIO=y +# CONFIG_C_AMBEN is not set +# CONFIG_C_AMBEN_B0 is not set +# CONFIG_C_AMBEN_B0_B1 is not set +# CONFIG_C_AMBEN_B0_B1_B2 is not set +CONFIG_C_AMBEN_ALL=y + +# +# EBIU_AMBCTL Control +# +CONFIG_BANK_0=0x7BB0 +CONFIG_BANK_1=0x5554 +CONFIG_BANK_2=0x7BB0 +CONFIG_BANK_3=0xFFC0 + +# +# Bus options (PCI, PCMCIA, EISA, MCA, ISA) +# +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Executable file formats +# +CONFIG_BINFMT_ELF_FDPIC=y +CONFIG_BINFMT_FLAT=y +CONFIG_BINFMT_ZFLAT=y +# CONFIG_BINFMT_SHARED_FLAT is not set +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +# CONFIG_PM is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y +# CONFIG_PM_WAKEUP_BY_GPIO is not set + +# +# CPU Frequency scaling +# +# CONFIG_CPU_FREQ is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +# CONFIG_IP_PNP_BOOTP is not set +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETLABEL is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +# CONFIG_MTD_CMDLINE_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +# CONFIG_MTD_CFI is not set +CONFIG_MTD_JEDECPROBE=m +CONFIG_MTD_GEN_PROBE=m +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +# CONFIG_MTD_CFI_AMDSTD is not set +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_RAM=y +CONFIG_MTD_ROM=m +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +CONFIG_MTD_COMPLEX_MAPPINGS=y +# CONFIG_MTD_PHYSMAP is not set +# CONFIG_MTD_GPIO_ADDR is not set +# CONFIG_MTD_UCLINUX is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_NAND is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +# CONFIG_BLK_DEV_NBD is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +CONFIG_MISC_DEVICES=y +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set +# CONFIG_SCSI_DMA is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_NETDEVICES_MULTIQUEUE is not set +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_SMC91X is not set +# CONFIG_SMSC911X is not set +# CONFIG_DM9000 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +CONFIG_INPUT_MISC=y +# CONFIG_INPUT_UINPUT is not set +# CONFIG_TWI_KEYPAD is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_AD9960 is not set +# CONFIG_SPI_ADC_BF533 is not set +# CONFIG_BF5xx_PPIFCD is not set +# CONFIG_BFIN_SIMPLE_TIMER is not set +# CONFIG_BF5xx_PPI is not set +# CONFIG_BFIN_SPORT is not set +# CONFIG_BFIN_TIMER_LATENCY is not set +# CONFIG_TWI_LCD is not set +CONFIG_SIMPLE_GPIO=m +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +# CONFIG_DEVKMEM is not set +# CONFIG_BFIN_JTAG_COMM is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_BFIN=y +CONFIG_SERIAL_BFIN_CONSOLE=y +CONFIG_SERIAL_BFIN_DMA=y +# CONFIG_SERIAL_BFIN_PIO is not set +CONFIG_SERIAL_BFIN_UART0=y +# CONFIG_BFIN_UART0_CTSRTS is not set +# CONFIG_SERIAL_BFIN_UART1 is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_BFIN_SPORT is not set +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set + +# +# CAN, the car bus and industrial fieldbus +# +# CONFIG_CAN4LINUX is not set +# CONFIG_IPMI_HANDLER is not set +# CONFIG_HW_RANDOM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y + +# +# I2C Hardware Bus support +# +CONFIG_I2C_BLACKFIN_TWI=y +CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=50 +# CONFIG_I2C_GPIO is not set +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_SIMTEC is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_PCA_PLATFORM is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_SENSORS_AD5252 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +# CONFIG_SPI is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_BFIN_WDT=y + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +# CONFIG_SOUND is not set +# CONFIG_HID_SUPPORT is not set +# CONFIG_USB_SUPPORT is not set +# CONFIG_MMC is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set + +# +# SPI RTC drivers +# + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +CONFIG_RTC_DRV_BFIN=y +# CONFIG_UIO is not set + +# +# File systems +# +# CONFIG_EXT2_FS is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_DNOTIFY is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +# CONFIG_TMPFS is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_YAFFS_FS is not set +# CONFIG_JFFS2_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=m +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +# CONFIG_NFSD is not set +CONFIG_LOCKD=m +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=m +# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +CONFIG_SMB_FS=m +# CONFIG_SMB_NLS_DEFAULT is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +CONFIG_DEBUG_FS=y +# CONFIG_HEADERS_CHECK is not set +# CONFIG_DEBUG_KERNEL is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +CONFIG_DEBUG_VERBOSE=y +CONFIG_DEBUG_MMRS=y +# CONFIG_DEBUG_DOUBLEFAULT is not set +CONFIG_DEBUG_HUNT_FOR_ZERO=y +CONFIG_DEBUG_BFIN_HWTRACE_ON=y +CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_OFF=y +# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE is not set +# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_TWO is not set +CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION=0 +# CONFIG_DEBUG_BFIN_HWTRACE_EXPAND is not set +# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set +CONFIG_EARLY_PRINTK=y +CONFIG_CPLB_INFO=y +CONFIG_ACCESS_CHECK=y + +# +# Security options +# +# CONFIG_KEYS is not set +CONFIG_SECURITY=y +# CONFIG_SECURITY_NETWORK is not set +# CONFIG_SECURITY_CAPABILITIES is not set +CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0 +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +# CONFIG_CRYPTO_MANAGER is not set +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +# CONFIG_CRYPTO_CBC is not set +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +# CONFIG_CRYPTO_ECB is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +# CONFIG_CRYPTO_MD5 is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_HW=y + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +CONFIG_CRC_CCITT=m +# CONFIG_CRC16 is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y diff --git a/arch/blackfin/include/asm/gpio.h b/arch/blackfin/include/asm/gpio.h index c7d287ca5d0..d8485624006 100644 --- a/arch/blackfin/include/asm/gpio.h +++ b/arch/blackfin/include/asm/gpio.h @@ -143,6 +143,57 @@ #define PERIPHERAL_USAGE 1 #define GPIO_USAGE 0 +#if defined(BF518_FAMILY) +#define MAX_BLACKFIN_GPIOS 40 + +#define GPIO_PF0 0 +#define GPIO_PF1 1 +#define GPIO_PF2 2 +#define GPIO_PF3 3 +#define GPIO_PF4 4 +#define GPIO_PF5 5 +#define GPIO_PF6 6 +#define GPIO_PF7 7 +#define GPIO_PF8 8 +#define GPIO_PF9 9 +#define GPIO_PF10 10 +#define GPIO_PF11 11 +#define GPIO_PF12 12 +#define GPIO_PF13 13 +#define GPIO_PF14 14 +#define GPIO_PF15 15 +#define GPIO_PG0 16 +#define GPIO_PG1 17 +#define GPIO_PG2 18 +#define GPIO_PG3 19 +#define GPIO_PG4 20 +#define GPIO_PG5 21 +#define GPIO_PG6 22 +#define GPIO_PG7 23 +#define GPIO_PG8 24 +#define GPIO_PG9 25 +#define GPIO_PG10 26 +#define GPIO_PG11 27 +#define GPIO_PG12 28 +#define GPIO_PG13 29 +#define GPIO_PG14 30 +#define GPIO_PG15 31 +#define GPIO_PH0 32 +#define GPIO_PH1 33 +#define GPIO_PH2 34 +#define GPIO_PH3 35 +#define GPIO_PH4 36 +#define GPIO_PH5 37 +#define GPIO_PH6 38 +#define GPIO_PH7 39 + +#define PORT_F GPIO_PF0 +#define PORT_G GPIO_PG0 +#define PORT_H GPIO_PH0 + +#endif + + #ifdef BF533_FAMILY #define MAX_BLACKFIN_GPIOS 16 diff --git a/arch/blackfin/kernel/bfin_gpio.c b/arch/blackfin/kernel/bfin_gpio.c index e129102ad09..5556e13993b 100644 --- a/arch/blackfin/kernel/bfin_gpio.c +++ b/arch/blackfin/kernel/bfin_gpio.c @@ -125,7 +125,7 @@ static struct gpio_port_t *gpio_bankb[gpio_bank(MAX_BLACKFIN_GPIOS)] = { }; #endif -#if defined(BF527_FAMILY) || defined(BF537_FAMILY) +#if defined(BF527_FAMILY) || defined(BF537_FAMILY) || defined(BF518_FAMILY) static struct gpio_port_t *gpio_bankb[gpio_bank(MAX_BLACKFIN_GPIOS)] = { (struct gpio_port_t *) PORTFIO, (struct gpio_port_t *) PORTGIO, @@ -139,7 +139,7 @@ static unsigned short *port_fer[gpio_bank(MAX_BLACKFIN_GPIOS)] = { }; #endif -#ifdef BF527_FAMILY +#if defined(BF527_FAMILY) || defined(BF518_FAMILY) static unsigned short *port_mux[gpio_bank(MAX_BLACKFIN_GPIOS)] = { (unsigned short *) PORTF_MUX, (unsigned short *) PORTG_MUX, @@ -206,7 +206,7 @@ static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PROG_INTB static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PORTF_INTB}; #endif -#ifdef BF527_FAMILY +#if defined(BF527_FAMILY) || defined(BF518_FAMILY) static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PORTF_INTB, IRQ_PORTG_INTB, IRQ_PORTH_INTB}; #endif @@ -268,7 +268,7 @@ static int cmp_label(unsigned short ident, const char *label) return -EINVAL; } -#if defined(BF527_FAMILY) || defined(BF537_FAMILY) +#if defined(BF527_FAMILY) || defined(BF537_FAMILY) || defined(BF518_FAMILY) static void port_setup(unsigned gpio, unsigned short usage) { if (!check_gpio(gpio)) { @@ -383,7 +383,7 @@ inline u16 get_portmux(unsigned short portno) return (pmux >> (2 * gpio_sub_n(portno)) & 0x3); } -#elif defined(BF527_FAMILY) +#elif defined(BF527_FAMILY) || defined(BF518_FAMILY) inline void portmux_setup(unsigned short portno, unsigned short function) { u16 pmux, ident = P_IDENT(portno); @@ -683,7 +683,7 @@ u32 bfin_pm_standby_setup(void) gpio_bankb[bank]->maskb = 0; if (mask) { -#if defined(BF527_FAMILY) || defined(BF537_FAMILY) +#if defined(BF527_FAMILY) || defined(BF537_FAMILY) || defined(BF518_FAMILY) gpio_bank_saved[bank].fer = *port_fer[bank]; #endif gpio_bank_saved[bank].inen = gpio_bankb[bank]->inen; @@ -728,7 +728,7 @@ void bfin_pm_standby_restore(void) bank = gpio_bank(i); if (mask) { -#if defined(BF527_FAMILY) || defined(BF537_FAMILY) +#if defined(BF527_FAMILY) || defined(BF537_FAMILY) || defined(BF518_FAMILY) *port_fer[bank] = gpio_bank_saved[bank].fer; #endif gpio_bankb[bank]->inen = gpio_bank_saved[bank].inen; @@ -754,9 +754,9 @@ void bfin_gpio_pm_hibernate_suspend(void) for (i = 0; i < MAX_BLACKFIN_GPIOS; i += GPIO_BANKSIZE) { bank = gpio_bank(i); -#if defined(BF527_FAMILY) || defined(BF537_FAMILY) +#if defined(BF527_FAMILY) || defined(BF537_FAMILY) || defined(BF518_FAMILY) gpio_bank_saved[bank].fer = *port_fer[bank]; -#ifdef BF527_FAMILY +#if defined(BF527_FAMILY) || defined(BF518_FAMILY) gpio_bank_saved[bank].mux = *port_mux[bank]; #else if (bank == 0) @@ -782,8 +782,8 @@ void bfin_gpio_pm_hibernate_restore(void) for (i = 0; i < MAX_BLACKFIN_GPIOS; i += GPIO_BANKSIZE) { bank = gpio_bank(i); -#if defined(BF527_FAMILY) || defined(BF537_FAMILY) -#ifdef BF527_FAMILY +#if defined(BF527_FAMILY) || defined(BF537_FAMILY) || defined(BF518_FAMILY) +#if defined(BF527_FAMILY) || defined(BF518_FAMILY) *port_mux[bank] = gpio_bank_saved[bank].mux; #else if (bank == 0) diff --git a/arch/blackfin/mach-bf518/Kconfig b/arch/blackfin/mach-bf518/Kconfig new file mode 100644 index 00000000000..00f2d370063 --- /dev/null +++ b/arch/blackfin/mach-bf518/Kconfig @@ -0,0 +1,233 @@ +if (BF51x) + +source "arch/blackfin/mach-bf518/boards/Kconfig" + +menu "BF518 Specific Configuration" + +comment "Alternative Multiplexing Scheme" + +choice + prompt "SPORT0" + default BF518_SPORT0_PORTG + help + Select PORT used for SPORT0. See Hardware Reference Manual + +config BF518_SPORT0_PORTF + bool "PORT F" + help + PORT F + +config BF518_SPORT0_PORTG + bool "PORT G" + help + PORT G +endchoice + +choice + prompt "SPORT0 TSCLK Location" + depends on BF518_SPORT0_PORTG + default BF518_SPORT0_TSCLK_PG10 + help + Select PIN used for SPORT0_TSCLK. See Hardware Reference Manual + +config BF518_SPORT0_TSCLK_PG10 + bool "PORT PG10" + help + PORT PG10 + +config BF518_SPORT0_TSCLK_PG14 + bool "PORT PG14" + help + PORT PG14 +endchoice + +choice + prompt "UART1" + default BF518_UART1_PORTF + help + Select PORT used for UART1. See Hardware Reference Manual + +config BF518_UART1_PORTF + bool "PORT F" + help + PORT F + +config BF518_UART1_PORTG + bool "PORT G" + help + PORT G +endchoice + +comment "Interrupt Priority Assignment" +menu "Priority" + +config IRQ_PLL_WAKEUP + int "IRQ_PLL_WAKEUP" + default 7 +config IRQ_DMA0_ERROR + int "IRQ_DMA0_ERROR" + default 7 +config IRQ_DMAR0_BLK + int "IRQ_DMAR0_BLK" + default 7 +config IRQ_DMAR1_BLK + int "IRQ_DMAR1_BLK" + default 7 +config IRQ_DMAR0_OVR + int "IRQ_DMAR0_OVR" + default 7 +config IRQ_DMAR1_OVR + int "IRQ_DMAR1_OVR" + default 7 +config IRQ_PPI_ERROR + int "IRQ_PPI_ERROR" + default 7 +config IRQ_MAC_ERROR + int "IRQ_MAC_ERROR" + default 7 +config IRQ_SPORT0_ERROR + int "IRQ_SPORT0_ERROR" + default 7 +config IRQ_SPORT1_ERROR + int "IRQ_SPORT1_ERROR" + default 7 +config IRQ_PTP_ERROR + int "IRQ_PTP_ERROR" + default 7 +config IRQ_UART0_ERROR + int "IRQ_UART0_ERROR" + default 7 +config IRQ_UART1_ERROR + int "IRQ_UART1_ERROR" + default 7 +config IRQ_RTC + int "IRQ_RTC" + default 8 +config IRQ_PPI + int "IRQ_PPI" + default 8 +config IRQ_SPORT0_RX + int "IRQ_SPORT0_RX" + default 9 +config IRQ_SPORT0_TX + int "IRQ_SPORT0_TX" + default 9 +config IRQ_SPORT1_RX + int "IRQ_SPORT1_RX" + default 9 +config IRQ_SPORT1_TX + int "IRQ_SPORT1_TX" + default 9 +config IRQ_TWI + int "IRQ_TWI" + default 10 +config IRQ_SPI0 + int "IRQ_SPI" + default 10 +config IRQ_UART0_RX + int "IRQ_UART0_RX" + default 10 +config IRQ_UART0_TX + int "IRQ_UART0_TX" + default 10 +config IRQ_UART1_RX + int "IRQ_UART1_RX" + default 10 +config IRQ_UART1_TX + int "IRQ_UART1_TX" + default 10 +config IRQ_OPTSEC + int "IRQ_OPTSEC" + default 11 +config IRQ_CNT + int "IRQ_CNT" + default 11 +config IRQ_MAC_RX + int "IRQ_MAC_RX" + default 11 +config IRQ_PORTH_INTA + int "IRQ_PORTH_INTA" + default 11 +config IRQ_MAC_TX + int "IRQ_MAC_TX/NFC" + default 11 +config IRQ_PORTH_INTB + int "IRQ_PORTH_INTB" + default 11 +config IRQ_TMR0 + int "IRQ_TMR0" + default 12 +config IRQ_TMR1 + int "IRQ_TMR1" + default 12 +config IRQ_TMR2 + int "IRQ_TMR2" + default 12 +config IRQ_TMR3 + int "IRQ_TMR3" + default 12 +config IRQ_TMR4 + int "IRQ_TMR4" + default 12 +config IRQ_TMR5 + int "IRQ_TMR5" + default 12 +config IRQ_TMR6 + int "IRQ_TMR6" + default 12 +config IRQ_TMR7 + int "IRQ_TMR7" + default 12 +config IRQ_PORTG_INTA + int "IRQ_PORTG_INTA" + default 12 +config IRQ_PORTG_INTB + int "IRQ_PORTG_INTB" + default 12 +config IRQ_MEM_DMA0 + int "IRQ_MEM_DMA0" + default 13 +config IRQ_MEM_DMA1 + int "IRQ_MEM_DMA1" + default 13 +config IRQ_WATCH + int "IRQ_WATCH" + default 13 +config IRQ_PORTF_INTA + int "IRQ_PORTF_INTA" + default 13 +config IRQ_PORTF_INTB + int "IRQ_PORTF_INTB" + default 13 +config IRQ_SPI0_ERROR + int "IRQ_SPI0_ERROR" + default 7 +config IRQ_SPI1_ERROR + int "IRQ_SPI1_ERROR" + default 7 +config IRQ_RSI_INT0 + int "IRQ_RSI_INT0" + default 7 +config IRQ_RSI_INT1 + int "IRQ_RSI_INT1" + default 7 +config IRQ_PWM_TRIP + int "IRQ_PWM_TRIP" + default 10 +config IRQ_PWM_SYNC + int "IRQ_PWM_SYNC" + default 10 +config IRQ_PTP_STAT + int "IRQ_PTP_STAT" + default 10 + + help + Enter the priority numbers between 7-13 ONLY. Others are Reserved. + This applies to all the above. It is not recommended to assign the + highest priority number 7 to UART or any other device. + +endmenu + +endmenu + +endif diff --git a/arch/blackfin/mach-bf518/Makefile b/arch/blackfin/mach-bf518/Makefile new file mode 100644 index 00000000000..9d5e16d07b5 --- /dev/null +++ b/arch/blackfin/mach-bf518/Makefile @@ -0,0 +1,7 @@ +# +# arch/blackfin/mach-bf518/Makefile +# + +extra-y := head.o + +obj-y := ints-priority.o dma.o diff --git a/arch/blackfin/mach-bf518/boards/Kconfig b/arch/blackfin/mach-bf518/boards/Kconfig new file mode 100644 index 00000000000..96163514ed2 --- /dev/null +++ b/arch/blackfin/mach-bf518/boards/Kconfig @@ -0,0 +1,12 @@ +choice + prompt "System type" + default BFIN518F_EZBRD + help + Select your board! + +config BFIN518F_EZBRD + bool "BF518F-EZBRD" + help + BF518-EZBRD board support. + +endchoice diff --git a/arch/blackfin/mach-bf518/boards/Makefile b/arch/blackfin/mach-bf518/boards/Makefile new file mode 100644 index 00000000000..172e859c3a7 --- /dev/null +++ b/arch/blackfin/mach-bf518/boards/Makefile @@ -0,0 +1,5 @@ +# +# arch/blackfin/mach-bf518/boards/Makefile +# + +obj-$(CONFIG_BFIN518F_EZBRD) += ezbrd.o diff --git a/arch/blackfin/mach-bf518/boards/ezbrd.c b/arch/blackfin/mach-bf518/boards/ezbrd.c new file mode 100644 index 00000000000..65bc602b5c9 --- /dev/null +++ b/arch/blackfin/mach-bf518/boards/ezbrd.c @@ -0,0 +1,613 @@ +/* + * File: arch/blackfin/mach-bf518/boards/ezbrd.c + * Based on: arch/blackfin/mach-bf527/boards/ezbrd.c + * Author: Bryan Wu <cooloney@kernel.org> + * + * Created: + * Description: + * + * Modified: + * Copyright 2005 National ICT Australia (NICTA) + * Copyright 2004-2008 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> +#include <linux/spi/spi.h> +#include <linux/spi/flash.h> + +#include <linux/i2c.h> +#include <linux/irq.h> +#include <linux/interrupt.h> +#include <asm/dma.h> +#include <asm/bfin5xx_spi.h> +#include <asm/reboot.h> +#include <asm/portmux.h> +#include <asm/dpmc.h> +#include <linux/spi/ad7877.h> + +/* + * Name the Board for the /proc/cpuinfo + */ +const char bfin_board_name[] = "BF518F-EZBRD"; + +/* + * Driver needs to know address, irq and flag pin. + */ + +#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) +static struct mtd_partition ezbrd_partitions[] = { + { + .name = "bootloader(nor)", + .size = 0x40000, + .offset = 0, + }, { + .name = "linux kernel(nor)", + .size = 0x1C0000, + .offset = MTDPART_OFS_APPEND, + }, { + .name = "file system(nor)", + .size = MTDPART_SIZ_FULL, + .offset = MTDPART_OFS_APPEND, + } +}; + +static struct physmap_flash_data ezbrd_flash_data = { + .width = 2, + .parts = ezbrd_partitions, + .nr_parts = ARRAY_SIZE(ezbrd_partitions), +}; + +static struct resource ezbrd_flash_resource = { + .start = 0x20000000, + .end = 0x203fffff, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device ezbrd_flash_device = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &ezbrd_flash_data, + }, + .num_resources = 1, + .resource = &ezbrd_flash_resource, +}; +#endif + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +static struct platform_device rtc_device = { + .name = "rtc-bfin", + .id = -1, +}; +#endif + +#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) +static struct platform_device bfin_mac_device = { + .name = "bfin_mac", +}; +#endif + +#if defined(CONFIG_MTD_M25P80) \ + || defined(CONFIG_MTD_M25P80_MODULE) +static struct mtd_partition bfin_spi_flash_partitions[] = { + { + .name = "bootloader(spi)", + .size = 0x00040000, + .offset = 0, + .mask_flags = MTD_CAP_ROM + }, { + .name = "linux kernel(spi)", + .size = MTDPART_SIZ_FULL, + .offset = MTDPART_OFS_APPEND, + } +}; + +static struct flash_platform_data bfin_spi_flash_data = { + .name = "m25p80", + .parts = bfin_spi_flash_partitions, + .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), + .type = "m25p16", +}; + +/* SPI flash chip (m25p64) */ +static struct bfin5xx_spi_chip spi_flash_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_SPI_ADC_BF533) \ + || defined(CONFIG_SPI_ADC_BF533_MODULE) +/* SPI ADC chip */ +static struct bfin5xx_spi_chip spi_adc_chip_info = { + .enable_dma = 1, /* use dma transfer with this chip*/ + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE) +static struct bfin5xx_spi_chip spi_mmc_chip_info = { + .enable_dma = 1, + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_PBX) +static struct bfin5xx_spi_chip spi_si3xxx_chip_info = { + .ctl_reg = 0x4, /* send zero */ + .enable_dma = 0, + .bits_per_word = 8, + .cs_change_per_word = 1, +}; +#endif + +#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE) +static struct bfin5xx_spi_chip spi_ad7877_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; + +static const struct ad7877_platform_data bfin_ad7877_ts_info = { + .model = 7877, + .vref_delay_usecs = 50, /* internal, no capacitor */ + .x_plate_ohms = 419, + .y_plate_ohms = 486, + .pressure_max = 1000, + .pressure_min = 0, + .stopacq_polarity = 1, + .first_conversion_delay = 3, + .acquisition_time = 1, + .averaging = 1, + .pen_down_acc_interval = 1, +}; +#endif + +#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \ + && defined(CONFIG_SND_SOC_WM8731_SPI) +static struct bfin5xx_spi_chip spi_wm8731_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) +static struct bfin5xx_spi_chip spidev_chip_info = { + .enable_dma = 0, + .bits_per_word = 8, +}; +#endif + +static struct spi_board_info bfin_spi_board_info[] __initdata = { +#if defined(CONFIG_MTD_M25P80) \ + || defined(CONFIG_MTD_M25P80_MODULE) + { + /* the modalias must be the same as spi device driver name */ + .modalias = "m25p80", /* Name of spi_driver for this device */ + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/ + .platform_data = &bfin_spi_flash_data, + .controller_data = &spi_flash_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_SPI_ADC_BF533) \ + || defined(CONFIG_SPI_ADC_BF533_MODULE) + { + .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ + .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. */ + .platform_data = NULL, /* No spi_driver specific config */ + .controller_data = &spi_adc_chip_info, + }, +#endif + +#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE) + { + .modalias = "spi_mmc_dummy", + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 0, + .platform_data = NULL, + .controller_data = &spi_mmc_chip_info, + .mode = SPI_MODE_3, + }, + { + .modalias = "spi_mmc", + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = CONFIG_SPI_MMC_CS_CHAN, + .platform_data = NULL, + .controller_data = &spi_mmc_chip_info, + .mode = SPI_MODE_3, + }, +#endif +#if defined(CONFIG_PBX) + { + .modalias = "fxs-spi", + .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 8 - CONFIG_J11_JUMPER, + .controller_data = &spi_si3xxx_chip_info, + .mode = SPI_MODE_3, + }, + { + .modalias = "fxo-spi", + .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 8 - CONFIG_J19_JUMPER, + .controller_data = &spi_si3xxx_chip_info, + .mode = SPI_MODE_3, + }, +#endif +#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE) + { + .modalias = "ad7877", + .platform_data = &bfin_ad7877_ts_info, + .irq = IRQ_PF8, + .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 2, + .controller_data = &spi_ad7877_chip_info, + }, +#endif +#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \ + && defined(CONFIG_SND_SOC_WM8731_SPI) + { + .modalias = "wm8731", + .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 5, + .controller_data = &spi_wm8731_chip_info, + .mode = SPI_MODE_0, + }, +#endif +#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) + { + .modalias = "spidev", + .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 1, + .controller_data = &spidev_chip_info, + }, +#endif +#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE) + { + .modalias = "bfin-lq035q1-spi", + .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 1, + .controller_data = &lq035q1_spi_chip_info, + .mode = SPI_CPHA | SPI_CPOL, + }, +#endif +}; + +/* SPI controller data */ +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +/* SPI (0) */ +static struct bfin5xx_spi_master bfin_spi0_info = { + .num_chipselect = 5, + .enable_dma = 1, /* master has the ability to do dma transfer */ + .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, +}; + +static struct resource bfin_spi0_resource[] = { + [0] = { + .start = SPI0_REGBASE, + .end = SPI0_REGBASE + 0xFF, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = CH_SPI0, + .end = CH_SPI0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_spi0_device = { + .name = "bfin-spi", + .id = 0, /* Bus number */ + .num_resources = ARRAY_SIZE(bfin_spi0_resource), + .resource = bfin_spi0_resource, + .dev = { + .platform_data = &bfin_spi0_info, /* Passed to driver */ + }, +}; + +/* SPI (1) */ +static struct bfin5xx_spi_master bfin_spi1_info = { + .num_chipselect = 5, + .enable_dma = 1, /* master has the ability to do dma transfer */ + .pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0}, +}; + +static struct resource bfin_spi1_resource[] = { + [0] = { + .start = SPI1_REGBASE, + .end = SPI1_REGBASE + 0xFF, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = CH_SPI1, + .end = CH_SPI1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_spi1_device = { + .name = "bfin-spi", + .id = 1, /* Bus number */ + .num_resources = ARRAY_SIZE(bfin_spi1_resource), + .resource = bfin_spi1_resource, + .dev = { + .platform_data = &bfin_spi1_info, /* Passed to driver */ + }, +}; +#endif /* spi master and devices */ + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +static struct resource bfin_uart_resources[] = { +#ifdef CONFIG_SERIAL_BFIN_UART0 + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART1 + { + .start = 0xFFC02000, + .end = 0xFFC020FF, + .flags = IORESOURCE_MEM, + }, +#endif +}; + +static struct platform_device bfin_uart_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart_resources), + .resource = bfin_uart_resources, +}; +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +static struct resource bfin_sir_resources[] = { +#ifdef CONFIG_BFIN_SIR0 + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, +#endif +#ifdef CONFIG_BFIN_SIR1 + { + .start = 0xFFC02000, + .end = 0xFFC020FF, + .flags = IORESOURCE_MEM, + }, +#endif +}; + +static struct platform_device bfin_sir_device = { + .name = "bfin_sir", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sir_resources), + .resource = bfin_sir_resources, +}; +#endif + +#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) +static struct resource bfin_twi0_resource[] = { + [0] = { + .start = TWI0_REGBASE, + .end = TWI0_REGBASE, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_TWI, + .end = IRQ_TWI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device i2c_bfin_twi_device = { + .name = "i2c-bfin-twi", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_twi0_resource), + .resource = bfin_twi0_resource, +}; +#endif + +#ifdef CONFIG_I2C_BOARDINFO +static struct i2c_board_info __initdata bfin_i2c_board_info[] = { +#if defined(CONFIG_TWI_LCD) || defined(CONFIG_TWI_LCD_MODULE) + { + I2C_BOARD_INFO("pcf8574_lcd", 0x22), + }, +#endif +#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE) + { + I2C_BOARD_INFO("pcf8574_keypad", 0x27), + .irq = IRQ_PF8, + }, +#endif +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) +static struct platform_device bfin_sport0_uart_device = { + .name = "bfin-sport-uart", + .id = 0, +}; + +static struct platform_device bfin_sport1_uart_device = { + .name = "bfin-sport-uart", + .id = 1, +}; +#endif + +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +#include <linux/input.h> +#include <linux/gpio_keys.h> + +static struct gpio_keys_button bfin_gpio_keys_table[] = { + {BTN_0, GPIO_PG0, 1, "gpio-keys: BTN0"}, + {BTN_1, GPIO_PG13, 1, "gpio-keys: BTN1"}, +}; + +static struct gpio_keys_platform_data bfin_gpio_keys_data = { + .buttons = bfin_gpio_keys_table, + .nbuttons = ARRAY_SIZE(bfin_gpio_keys_table), +}; + +static struct platform_device bfin_device_gpiokeys = { + .name = "gpio-keys", + .dev = { + .platform_data = &bfin_gpio_keys_data, + }, +}; +#endif + +static struct resource bfin_gpios_resources = { + .start = 0, + .end = MAX_BLACKFIN_GPIOS - 1, + .flags = IORESOURCE_IRQ, +}; + +static struct platform_device bfin_gpios_device = { + .name = "simple-gpio", + .id = -1, + .num_resources = 1, + .resource = &bfin_gpios_resources, +}; + +static const unsigned int cclk_vlev_datasheet[] = +{ + VRPAIR(VLEV_100, 400000000), + VRPAIR(VLEV_105, 426000000), + VRPAIR(VLEV_110, 500000000), + VRPAIR(VLEV_115, 533000000), + VRPAIR(VLEV_120, 600000000), +}; + +static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = { + .tuple_tab = cclk_vlev_datasheet, + .tabsize = ARRAY_SIZE(cclk_vlev_datasheet), + .vr_settling_time = 25 /* us */, +}; + +static struct platform_device bfin_dpmc = { + .name = "bfin dpmc", + .dev = { + .platform_data = &bfin_dmpc_vreg_data, + }, +}; + +static struct platform_device *stamp_devices[] __initdata = { + + &bfin_dpmc, + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) + &rtc_device, +#endif + +#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) + &bfin_mac_device, +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + &bfin_spi0_device, + &bfin_spi1_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) + &bfin_uart_device, +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) + &bfin_sir_device, +#endif + +#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) + &i2c_bfin_twi_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) + &bfin_sport0_uart_device, + &bfin_sport1_uart_device, +#endif + +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) + &bfin_device_gpiokeys, +#endif + +#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) + &ezbrd_flash_device, +#endif + + &bfin_gpios_device, +}; + +static int __init ezbrd_init(void) +{ + printk(KERN_INFO "%s(): registering device resources\n", __func__); + +#ifdef CONFIG_I2C_BOARDINFO + i2c_register_board_info(0, bfin_i2c_board_info, + ARRAY_SIZE(bfin_i2c_board_info)); +#endif + + platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices)); + spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); + return 0; +} + +arch_initcall(ezbrd_init); + +void native_machine_restart(char *cmd) +{ + /* workaround reboot hang when booting from SPI */ + if ((bfin_read_SYSCR() & 0x7) == 0x3) + bfin_gpio_reset_spi0_ssel1(); +} + +void bfin_get_ether_addr(char *addr) +{ + /* the MAC is stored in OTP memory page 0xDF */ + u32 ret; + u64 otp_mac; + u32 (*otp_read)(u32 page, u32 flags, u64 *page_content) = (void *)0xEF00001A; + + ret = otp_read(0xDF, 0x00, &otp_mac); + if (!(ret & 0x1)) { + char *otp_mac_p = (char *)&otp_mac; + for (ret = 0; ret < 6; ++ret) + addr[ret] = otp_mac_p[5 - ret]; + } +} +EXPORT_SYMBOL(bfin_get_ether_addr); diff --git a/arch/blackfin/mach-bf518/dma.c b/arch/blackfin/mach-bf518/dma.c new file mode 100644 index 00000000000..0d06ced01ce --- /dev/null +++ b/arch/blackfin/mach-bf518/dma.c @@ -0,0 +1,118 @@ +/* + * File: arch/blackfin/mach-bf518/dma.c + * Based on: + * Author: Bryan Wu <cooloney@kernel.org> + * + * Created: + * Description: This file contains the simple DMA Implementation for Blackfin + * + * Modified: + * Copyright 2004-2008 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ +#include <linux/module.h> + +#include <asm/blackfin.h> +#include <asm/dma.h> + +struct dma_register *dma_io_base_addr[MAX_BLACKFIN_DMA_CHANNEL] = { + (struct dma_register *) DMA0_NEXT_DESC_PTR, + (struct dma_register *) DMA1_NEXT_DESC_PTR, + (struct dma_register *) DMA2_NEXT_DESC_PTR, + (struct dma_register *) DMA3_NEXT_DESC_PTR, + (struct dma_register *) DMA4_NEXT_DESC_PTR, + (struct dma_register *) DMA5_NEXT_DESC_PTR, + (struct dma_register *) DMA6_NEXT_DESC_PTR, + (struct dma_register *) DMA7_NEXT_DESC_PTR, + (struct dma_register *) DMA8_NEXT_DESC_PTR, + (struct dma_register *) DMA9_NEXT_DESC_PTR, + (struct dma_register *) DMA10_NEXT_DESC_PTR, + (struct dma_register *) DMA11_NEXT_DESC_PTR, + (struct dma_register *) MDMA_S0_NEXT_DESC_PTR, + (struct dma_register *) MDMA_D0_NEXT_DESC_PTR, + (struct dma_register *) MDMA_S1_NEXT_DESC_PTR, + (struct dma_register *) MDMA_D1_NEXT_DESC_PTR, +}; +EXPORT_SYMBOL(dma_io_base_addr); + +int channel2irq(unsigned int channel) +{ + int ret_irq = -1; + + switch (channel) { + case CH_PPI: + ret_irq = IRQ_PPI; + break; + + case CH_EMAC_RX: + ret_irq = IRQ_MAC_RX; + break; + + case CH_EMAC_TX: + ret_irq = IRQ_MAC_TX; + break; + + case CH_UART1_RX: + ret_irq = IRQ_UART1_RX; + break; + + case CH_UART1_TX: + ret_irq = IRQ_UART1_TX; + break; + + case CH_SPORT0_RX: + ret_irq = IRQ_SPORT0_RX; + break; + + case CH_SPORT0_TX: + ret_irq = IRQ_SPORT0_TX; + break; + + case CH_SPORT1_RX: + ret_irq = IRQ_SPORT1_RX; + break; + + case CH_SPORT1_TX: + ret_irq = IRQ_SPORT1_TX; + break; + + case CH_SPI0: + ret_irq = IRQ_SPI0; + break; + + case CH_UART0_RX: + ret_irq = IRQ_UART0_RX; + break; + + case CH_UART0_TX: + ret_irq = IRQ_UART0_TX; + break; + + case CH_MEM_STREAM0_SRC: + case CH_MEM_STREAM0_DEST: + ret_irq = IRQ_MEM_DMA0; + break; + + case CH_MEM_STREAM1_SRC: + case CH_MEM_STREAM1_DEST: + ret_irq = IRQ_MEM_DMA1; + break; + } + return ret_irq; +} diff --git a/arch/blackfin/mach-bf518/head.S b/arch/blackfin/mach-bf518/head.S new file mode 100644 index 00000000000..771bf7e477f --- /dev/null +++ b/arch/blackfin/mach-bf518/head.S @@ -0,0 +1,146 @@ +/* + * File: arch/blackfin/mach-bf518/head.S + * Based on: arch/blackfin/mach-bf527/head.S + * Author: Bryan Wu <cooloney@kernel.org> + * + * Created: 2008 + * Description: Startup code for Blackfin BF51x + * + * Modified: + * Copyright 2004-2008 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <linux/linkage.h> +#include <linux/init.h> +#include <asm/blackfin.h> +#ifdef CONFIG_BFIN_KERNEL_CLOCK +#include <asm/mach-common/clocks.h> +#include <asm/mach/mem_init.h> +#endif + +.section .l1.text +#ifdef CONFIG_BFIN_KERNEL_CLOCK +ENTRY(_start_dma_code) + + /* Enable PHY CLK buffer output */ + p0.h = hi(VR_CTL); + p0.l = lo(VR_CTL); + r0.l = w[p0]; + bitset(r0, 14); + w[p0] = r0.l; + ssync; + + p0.h = hi(SIC_IWR0); + p0.l = lo(SIC_IWR0); + r0.l = 0x1; + r0.h = 0x0; + [p0] = r0; + ssync; + + /* + * Set PLL_CTL + * - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors + * - [8] = BYPASS : BYPASS the PLL, run CLKIN into CCLK/SCLK + * - [7] = output delay (add 200ps of delay to mem signals) + * - [6] = input delay (add 200ps of input delay to mem signals) + * - [5] = PDWN : 1=All Clocks off + * - [3] = STOPCK : 1=Core Clock off + * - [1] = PLL_OFF : 1=Disable Power to PLL + * - [0] = DF : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL + * all other bits set to zero + */ + + p0.h = hi(PLL_LOCKCNT); + p0.l = lo(PLL_LOCKCNT); + r0 = 0x300(Z); + w[p0] = r0.l; + ssync; + + P2.H = hi(EBIU_SDGCTL); + P2.L = lo(EBIU_SDGCTL); + R0 = [P2]; + BITSET (R0, 24); + [P2] = R0; + ssync; + + r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */ + r0 = r0 << 9; /* Shift it over, */ + r1 = CLKIN_HALF; /* Do we need to divide CLKIN by 2?*/ + r0 = r1 | r0; + r1 = PLL_BYPASS; /* Bypass the PLL? */ + r1 = r1 << 8; /* Shift it over */ + r0 = r1 | r0; /* add them all together */ +#ifdef ANOMALY_05000265 + BITSET(r0, 15); /* Add 250 mV of hysteresis to SPORT input pins */ +#endif + + p0.h = hi(PLL_CTL); + p0.l = lo(PLL_CTL); /* Load the address */ + cli r2; /* Disable interrupts */ + ssync; + w[p0] = r0.l; /* Set the value */ + idle; /* Wait for the PLL to stablize */ + sti r2; /* Enable interrupts */ + +.Lcheck_again: + p0.h = hi(PLL_STAT); + p0.l = lo(PLL_STAT); + R0 = W[P0](Z); + CC = BITTST(R0,5); + if ! CC jump .Lcheck_again; + + /* Configure SCLK & CCLK Dividers */ + r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV); + p0.h = hi(PLL_DIV); + p0.l = lo(PLL_DIV); + w[p0] = r0.l; + ssync; + + p0.l = lo(EBIU_SDRRC); + p0.h = hi(EBIU_SDRRC); + r0 = mem_SDRRC; + w[p0] = r0.l; + ssync; + + P2.H = hi(EBIU_SDGCTL); + P2.L = lo(EBIU_SDGCTL); + R0 = [P2]; + BITCLR (R0, 24); + p0.h = hi(EBIU_SDSTAT); + p0.l = lo(EBIU_SDSTAT); + r2.l = w[p0]; + cc = bittst(r2,3); + if !cc jump .Lskip; + NOP; + BITSET (R0, 23); +.Lskip: + [P2] = R0; + SSYNC; + + R0.L = lo(mem_SDGCTL); + R0.H = hi(mem_SDGCTL); + R1 = [p2]; + R1 = R1 | R0; + [P2] = R1; + SSYNC; + + RTS; +ENDPROC(_start_dma_code) +#endif /* CONFIG_BFIN_KERNEL_CLOCK */ diff --git a/arch/blackfin/mach-bf518/include/mach/anomaly.h b/arch/blackfin/mach-bf518/include/mach/anomaly.h new file mode 100644 index 00000000000..5a94f97f04a --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/anomaly.h @@ -0,0 +1,77 @@ +/* + * File: include/asm-blackfin/mach-bf518/anomaly.h + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * Copyright (C) 2004-2008 Analog Devices Inc. + * Licensed under the GPL-2 or later. + */ + +/* This file shoule be up to date with: + * - ???? + */ + +#ifndef _MACH_ANOMALY_H_ +#define _MACH_ANOMALY_H_ + +/* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot2 Not Supported */ +#define ANOMALY_05000074 (1) +/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */ +#define ANOMALY_05000122 (1) +/* False Hardware Error from an Access in the Shadow of a Conditional Branch */ +#define ANOMALY_05000245 (1) +/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */ +#define ANOMALY_05000265 (1) +/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */ +#define ANOMALY_05000310 (1) +/* PPI Underflow Error Goes Undetected in ITU-R 656 Mode */ +#define ANOMALY_05000366 (1) +/* Lockbox SESR Firmware Does Not Save/Restore Full Context */ +#define ANOMALY_05000405 (1) +/* Lockbox Firmware Memory Cleanup Routine Does not Clear Registers */ +#define ANOMALY_05000408 (1) +/* Speculative Fetches Can Cause Undesired External FIFO Operations */ +#define ANOMALY_05000416 (1) +/* TWI Fall Time (Tof) May Violate the Minimum I2C Specification */ +#define ANOMALY_05000421 (1) +/* TWI Input Capacitance (Ci) May Violate the Maximum I2C Specification */ +#define ANOMALY_05000422 (1) +/* Speculative Fetches of Indirect-Pointer Instructions Can Cause False Hardware Errors */ +#define ANOMALY_05000426 (1) +/* Software System Reset Corrupts PLL_LOCKCNT Register */ +#define ANOMALY_05000430 (1) +/* Incorrect Use of Stack in Lockbox Firmware During Authentication */ +#define ANOMALY_05000431 (1) +/* Certain SIC Registers are not Reset After Soft or Core Double Fault Reset */ +#define ANOMALY_05000435 (1) +/* PORTx_DRIVE and PORTx_HYSTERESIS Registers Read Back Incorrect Values */ +#define ANOMALY_05000438 (1) +/* Preboot Cannot be Used to Program the PLL_DIV Register */ +#define ANOMALY_05000439 (1) +/* bfrom_SysControl() Cannot be Used to Write the PLL_DIV Register */ +#define ANOMALY_05000440 (1) +/* IFLUSH Instruction at End of Hardware Loop Causes Infinite Stall */ +#define ANOMALY_05000443 (1) +/* Incorrect L1 Instruction Bank B Memory Map Location */ +#define ANOMALY_05000444 (1) + +/* Anomalies that don't exist on this proc */ +#define ANOMALY_05000125 (0) +#define ANOMALY_05000158 (0) +#define ANOMALY_05000183 (0) +#define ANOMALY_05000198 (0) +#define ANOMALY_05000230 (0) +#define ANOMALY_05000244 (0) +#define ANOMALY_05000261 (0) +#define ANOMALY_05000263 (0) +#define ANOMALY_05000266 (0) +#define ANOMALY_05000273 (0) +#define ANOMALY_05000285 (0) +#define ANOMALY_05000307 (0) +#define ANOMALY_05000311 (0) +#define ANOMALY_05000312 (0) +#define ANOMALY_05000323 (0) +#define ANOMALY_05000353 (0) +#define ANOMALY_05000363 (0) +#define ANOMALY_05000386 (0) + +#endif diff --git a/arch/blackfin/mach-bf518/include/mach/bf518.h b/arch/blackfin/mach-bf518/include/mach/bf518.h new file mode 100644 index 00000000000..78da1a07ee7 --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/bf518.h @@ -0,0 +1,132 @@ +/* + * File: include/asm-blackfin/mach-bf518/bf518.h + * Based on: include/asm-blackfin/mach-bf527/bf527.h + * Author: Michael Hennerich (michael.hennerich@analog.com) + * + * Created: + * Description: SYSTEM MMR REGISTER AND MEMORY MAP FOR ADSP-BF518 + * + * Modified: + * Copyright 2004-2007 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#ifndef __MACH_BF518_H__ +#define __MACH_BF518_H__ + +#define OFFSET_(x) ((x) & 0x0000FFFF) + +/*some misc defines*/ +#define IMASK_IVG15 0x8000 +#define IMASK_IVG14 0x4000 +#define IMASK_IVG13 0x2000 +#define IMASK_IVG12 0x1000 + +#define IMASK_IVG11 0x0800 +#define IMASK_IVG10 0x0400 +#define IMASK_IVG9 0x0200 +#define IMASK_IVG8 0x0100 + +#define IMASK_IVG7 0x0080 +#define IMASK_IVGTMR 0x0040 +#define IMASK_IVGHW 0x0020 + +/***************************/ + +#define BFIN_DSUBBANKS 4 +#define BFIN_DWAYS 2 +#define BFIN_DLINES 64 +#define BFIN_ISUBBANKS 4 +#define BFIN_IWAYS 4 +#define BFIN_ILINES 32 + +#define WAY0_L 0x1 +#define WAY1_L 0x2 +#define WAY01_L 0x3 +#define WAY2_L 0x4 +#define WAY02_L 0x5 +#define WAY12_L 0x6 +#define WAY012_L 0x7 + +#define WAY3_L 0x8 +#define WAY03_L 0x9 +#define WAY13_L 0xA +#define WAY013_L 0xB + +#define WAY32_L 0xC +#define WAY320_L 0xD +#define WAY321_L 0xE +#define WAYALL_L 0xF + +#define DMC_ENABLE (2<<2) /*yes, 2, not 1 */ + +/********************************* EBIU Settings ************************************/ +#define AMBCTL0VAL ((CONFIG_BANK_1 << 16) | CONFIG_BANK_0) +#define AMBCTL1VAL ((CONFIG_BANK_3 << 16) | CONFIG_BANK_2) + +#ifdef CONFIG_C_AMBEN_ALL +#define V_AMBEN AMBEN_ALL +#endif +#ifdef CONFIG_C_AMBEN +#define V_AMBEN 0x0 +#endif +#ifdef CONFIG_C_AMBEN_B0 +#define V_AMBEN AMBEN_B0 +#endif +#ifdef CONFIG_C_AMBEN_B0_B1 +#define V_AMBEN AMBEN_B0_B1 +#endif +#ifdef CONFIG_C_AMBEN_B0_B1_B2 +#define V_AMBEN AMBEN_B0_B1_B2 +#endif +#ifdef CONFIG_C_AMCKEN +#define V_AMCKEN AMCKEN +#else +#define V_AMCKEN 0x0 +#endif +#ifdef CONFIG_C_CDPRIO +#define V_CDPRIO 0x100 +#else +#define V_CDPRIO 0x0 +#endif + +#define AMGCTLVAL (V_AMBEN | V_AMCKEN | V_CDPRIO) + +#ifdef CONFIG_BF518 +#define CPU "BF518" +#define CPUID 0x27e8 +#endif +#ifdef CONFIG_BF516 +#define CPU "BF516" +#define CPUID 0x27e8 +#endif +#ifdef CONFIG_BF514 +#define CPU "BF514" +#define CPUID 0x27e8 +#endif +#ifdef CONFIG_BF512 +#define CPU "BF512" +#define CPUID 0x27e8 +#endif + +#ifndef CPU +#error "Unknown CPU type - This kernel doesn't seem to be configured properly" +#endif + +#endif /* __MACH_BF518_H__ */ diff --git a/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h new file mode 100644 index 00000000000..b50a63b975a --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h @@ -0,0 +1,169 @@ +/* + * file: include/asm-blackfin/mach-bf518/bfin_serial_5xx.h + * based on: + * author: + * + * created: + * description: + * blackfin serial driver head file + * rev: + * + * modified: + * + * + * bugs: enter bugs at http://blackfin.uclinux.org/ + * + * this program is free software; you can redistribute it and/or modify + * it under the terms of the gnu general public license as published by + * the free software foundation; either version 2, or (at your option) + * any later version. + * + * this program is distributed in the hope that it will be useful, + * but without any warranty; without even the implied warranty of + * merchantability or fitness for a particular purpose. see the + * gnu general public license for more details. + * + * you should have received a copy of the gnu general public license + * along with this program; see the file copying. + * if not, write to the free software foundation, + * 59 temple place - suite 330, boston, ma 02111-1307, usa. + */ + +#include <linux/serial.h> +#include <asm/dma.h> +#include <asm/portmux.h> + +#define UART_GET_CHAR(uart) bfin_read16(((uart)->port.membase + OFFSET_RBR)) +#define UART_GET_DLL(uart) bfin_read16(((uart)->port.membase + OFFSET_DLL)) +#define UART_GET_IER(uart) bfin_read16(((uart)->port.membase + OFFSET_IER)) +#define UART_GET_DLH(uart) bfin_read16(((uart)->port.membase + OFFSET_DLH)) +#define UART_GET_IIR(uart) bfin_read16(((uart)->port.membase + OFFSET_IIR)) +#define UART_GET_LCR(uart) bfin_read16(((uart)->port.membase + OFFSET_LCR)) +#define UART_GET_GCTL(uart) bfin_read16(((uart)->port.membase + OFFSET_GCTL)) + +#define UART_PUT_CHAR(uart, v) bfin_write16(((uart)->port.membase + OFFSET_THR), v) +#define UART_PUT_DLL(uart, v) bfin_write16(((uart)->port.membase + OFFSET_DLL), v) +#define UART_PUT_IER(uart, v) bfin_write16(((uart)->port.membase + OFFSET_IER), v) +#define UART_SET_IER(uart, v) UART_PUT_IER(uart, UART_GET_IER(uart) | (v)) +#define UART_CLEAR_IER(uart, v) UART_PUT_IER(uart, UART_GET_IER(uart) & ~(v)) +#define UART_PUT_DLH(uart, v) bfin_write16(((uart)->port.membase + OFFSET_DLH), v) +#define UART_PUT_LCR(uart, v) bfin_write16(((uart)->port.membase + OFFSET_LCR), v) +#define UART_PUT_GCTL(uart, v) bfin_write16(((uart)->port.membase + OFFSET_GCTL), v) + +#define UART_SET_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0) +#define UART_CLEAR_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0) + +#define UART_GET_CTS(x) gpio_get_value(x->cts_pin) +#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1) +#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0) +#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v) +#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0) + +#if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART1_CTSRTS) +# define CONFIG_SERIAL_BFIN_CTSRTS + +# ifndef CONFIG_UART0_CTS_PIN +# define CONFIG_UART0_CTS_PIN -1 +# endif + +# ifndef CONFIG_UART0_RTS_PIN +# define CONFIG_UART0_RTS_PIN -1 +# endif + +# ifndef CONFIG_UART1_CTS_PIN +# define CONFIG_UART1_CTS_PIN -1 +# endif + +# ifndef CONFIG_UART1_RTS_PIN +# define CONFIG_UART1_RTS_PIN -1 +# endif +#endif + +#define BFIN_UART_TX_FIFO_SIZE 2 + +/* + * The pin configuration is different from schematic + */ +struct bfin_serial_port { + struct uart_port port; + unsigned int old_status; + unsigned int lsr; +#ifdef CONFIG_SERIAL_BFIN_DMA + int tx_done; + int tx_count; + struct circ_buf rx_dma_buf; + struct timer_list rx_dma_timer; + int rx_dma_nrows; + unsigned int tx_dma_channel; + unsigned int rx_dma_channel; + struct work_struct tx_dma_workqueue; +#endif +#ifdef CONFIG_SERIAL_BFIN_CTSRTS + struct timer_list cts_timer; + int cts_pin; + int rts_pin; +#endif +}; + +/* The hardware clears the LSR bits upon read, so we need to cache + * some of the more fun bits in software so they don't get lost + * when checking the LSR in other code paths (TX). + */ +static inline unsigned int UART_GET_LSR(struct bfin_serial_port *uart) +{ + unsigned int lsr = bfin_read16(uart->port.membase + OFFSET_LSR); + uart->lsr |= (lsr & (BI|FE|PE|OE)); + return lsr | uart->lsr; +} + +static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart) +{ + uart->lsr = 0; + bfin_write16(uart->port.membase + OFFSET_LSR, -1); +} + +struct bfin_serial_res { + unsigned long uart_base_addr; + int uart_irq; +#ifdef CONFIG_SERIAL_BFIN_DMA + unsigned int uart_tx_dma_channel; + unsigned int uart_rx_dma_channel; +#endif +#ifdef CONFIG_SERIAL_BFIN_CTSRTS + int uart_cts_pin; + int uart_rts_pin; +#endif +}; + +struct bfin_serial_res bfin_serial_resource[] = { +#ifdef CONFIG_SERIAL_BFIN_UART0 + { + 0xFFC00400, + IRQ_UART0_RX, +#ifdef CONFIG_SERIAL_BFIN_DMA + CH_UART0_TX, + CH_UART0_RX, +#endif +#ifdef CONFIG_BFIN_UART0_CTSRTS + CONFIG_UART0_CTS_PIN, + CONFIG_UART0_RTS_PIN, +#endif + }, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART1 + { + 0xFFC02000, + IRQ_UART1_RX, +#ifdef CONFIG_SERIAL_BFIN_DMA + CH_UART1_TX, + CH_UART1_RX, +#endif +#ifdef CONFIG_BFIN_UART1_CTSRTS + CONFIG_UART1_CTS_PIN, + CONFIG_UART1_RTS_PIN, +#endif + }, +#endif +}; + +#define DRIVER_NAME "bfin-uart" diff --git a/arch/blackfin/mach-bf518/include/mach/bfin_sir.h b/arch/blackfin/mach-bf518/include/mach/bfin_sir.h new file mode 100644 index 00000000000..cfd8ad4f1f2 --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/bfin_sir.h @@ -0,0 +1,142 @@ +/* + * Blackfin Infra-red Driver + * + * Copyright 2006-2008 Analog Devices Inc. + * + * Enter bugs at http://blackfin.uclinux.org/ + * + * Licensed under the GPL-2 or later. + * + */ + +#include <linux/serial.h> +#include <asm/dma.h> +#include <asm/portmux.h> + +#define SIR_UART_GET_CHAR(port) bfin_read16((port)->membase + OFFSET_RBR) +#define SIR_UART_GET_DLL(port) bfin_read16((port)->membase + OFFSET_DLL) +#define SIR_UART_GET_IER(port) bfin_read16((port)->membase + OFFSET_IER) +#define SIR_UART_GET_DLH(port) bfin_read16((port)->membase + OFFSET_DLH) +#define SIR_UART_GET_IIR(port) bfin_read16((port)->membase + OFFSET_IIR) +#define SIR_UART_GET_LCR(port) bfin_read16((port)->membase + OFFSET_LCR) +#define SIR_UART_GET_GCTL(port) bfin_read16((port)->membase + OFFSET_GCTL) + +#define SIR_UART_PUT_CHAR(port, v) bfin_write16(((port)->membase + OFFSET_THR), v) +#define SIR_UART_PUT_DLL(port, v) bfin_write16(((port)->membase + OFFSET_DLL), v) +#define SIR_UART_PUT_IER(port, v) bfin_write16(((port)->membase + OFFSET_IER), v) +#define SIR_UART_PUT_DLH(port, v) bfin_write16(((port)->membase + OFFSET_DLH), v) +#define SIR_UART_PUT_LCR(port, v) bfin_write16(((port)->membase + OFFSET_LCR), v) +#define SIR_UART_PUT_GCTL(port, v) bfin_write16(((port)->membase + OFFSET_GCTL), v) + +#ifdef CONFIG_SIR_BFIN_DMA +struct dma_rx_buf { + char *buf; + int head; + int tail; + }; +#endif /* CONFIG_SIR_BFIN_DMA */ + +struct bfin_sir_port { + unsigned char __iomem *membase; + unsigned int irq; + unsigned int lsr; + unsigned long clk; + struct net_device *dev; +#ifdef CONFIG_SIR_BFIN_DMA + int tx_done; + struct dma_rx_buf rx_dma_buf; + struct timer_list rx_dma_timer; + int rx_dma_nrows; +#endif /* CONFIG_SIR_BFIN_DMA */ + unsigned int tx_dma_channel; + unsigned int rx_dma_channel; +}; + +struct bfin_sir_port sir_ports[BFIN_UART_NR_PORTS]; + +struct bfin_sir_port_res { + unsigned long base_addr; + int irq; + unsigned int rx_dma_channel; + unsigned int tx_dma_channel; +}; + +struct bfin_sir_port_res bfin_sir_port_resource[] = { +#ifdef CONFIG_BFIN_SIR0 + { + 0xFFC00400, + IRQ_UART0_RX, + CH_UART0_RX, + CH_UART0_TX, + }, +#endif +#ifdef CONFIG_BFIN_SIR1 + { + 0xFFC02000, + IRQ_UART1_RX, + CH_UART1_RX, + CH_UART1_TX, + }, +#endif +}; + +int nr_sirs = ARRAY_SIZE(bfin_sir_port_resource); + +struct bfin_sir_self { + struct bfin_sir_port *sir_port; + spinlock_t lock; + unsigned int open; + int speed; + int newspeed; + + struct sk_buff *txskb; + struct sk_buff *rxskb; + struct net_device_stats stats; + struct device *dev; + struct irlap_cb *irlap; + struct qos_info qos; + + iobuff_t tx_buff; + iobuff_t rx_buff; + + struct work_struct work; + int mtt; +}; + +static inline unsigned int SIR_UART_GET_LSR(struct bfin_sir_port *port) +{ + unsigned int lsr = bfin_read16(port->membase + OFFSET_LSR); + port->lsr |= (lsr & (BI|FE|PE|OE)); + return lsr | port->lsr; +} + +static inline void SIR_UART_CLEAR_LSR(struct bfin_sir_port *port) +{ + port->lsr = 0; + bfin_read16(port->membase + OFFSET_LSR); +} + +#define DRIVER_NAME "bfin_sir" + +static int bfin_sir_hw_init(void) +{ + int ret = -ENODEV; +#ifdef CONFIG_BFIN_SIR0 + ret = peripheral_request(P_UART0_TX, DRIVER_NAME); + if (ret) + return ret; + ret = peripheral_request(P_UART0_RX, DRIVER_NAME); + if (ret) + return ret; +#endif + +#ifdef CONFIG_BFIN_SIR1 + ret = peripheral_request(P_UART1_TX, DRIVER_NAME); + if (ret) + return ret; + ret = peripheral_request(P_UART1_RX, DRIVER_NAME); + if (ret) + return ret; +#endif + return ret; +} diff --git a/arch/blackfin/mach-bf518/include/mach/blackfin.h b/arch/blackfin/mach-bf518/include/mach/blackfin.h new file mode 100644 index 00000000000..d1a2b9ca622 --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/blackfin.h @@ -0,0 +1,105 @@ +/* + * File: include/asm-blackfin/mach-bf518/blackfin.h + * Based on: + * Author: + * + * Created: + * Description: + * + * Rev: + * + * Modified: + * + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _MACH_BLACKFIN_H_ +#define _MACH_BLACKFIN_H_ + +#define BF518_FAMILY + +#include "bf518.h" +#include "mem_map.h" +#include "defBF512.h" +#include "anomaly.h" + +#if defined(CONFIG_BF518) +#include "defBF518.h" +#endif + +#if defined(CONFIG_BF516) +#include "defBF516.h" +#endif + +#if defined(CONFIG_BF514) +#include "defBF514.h" +#endif + +#if defined(CONFIG_BF512) +#include "defBF512.h" +#endif + +#if !defined(__ASSEMBLY__) +#include "cdefBF512.h" + +#if defined(CONFIG_BF518) +#include "cdefBF518.h" +#endif + +#if defined(CONFIG_BF516) +#include "cdefBF516.h" +#endif + +#if defined(CONFIG_BF514) +#include "cdefBF514.h" +#endif +#endif + +/* UART_IIR Register */ +#define STATUS(x) ((x << 1) & 0x06) +#define STATUS_P1 0x02 +#define STATUS_P0 0x01 + +#define BFIN_UART_NR_PORTS 2 + +#define OFFSET_THR 0x00 /* Transmit Holding register */ +#define OFFSET_RBR 0x00 /* Receive Buffer register */ +#define OFFSET_DLL 0x00 /* Divisor Latch (Low-Byte) */ +#define OFFSET_IER 0x04 /* Interrupt Enable Register */ +#define OFFSET_DLH 0x04 /* Divisor Latch (High-Byte) */ +#define OFFSET_IIR 0x08 /* Interrupt Identification Register */ +#define OFFSET_LCR 0x0C /* Line Control Register */ +#define OFFSET_MCR 0x10 /* Modem Control Register */ +#define OFFSET_LSR 0x14 /* Line Status Register */ +#define OFFSET_MSR 0x18 /* Modem Status Register */ +#define OFFSET_SCR 0x1C /* SCR Scratch Register */ +#define OFFSET_GCTL 0x24 /* Global Control Register */ + +/* DPMC*/ +#define bfin_read_STOPCK_OFF() bfin_read_STOPCK() +#define bfin_write_STOPCK_OFF(val) bfin_write_STOPCK(val) +#define STOPCK_OFF STOPCK + +/* PLL_DIV Masks */ +#define CCLK_DIV1 CSEL_DIV1 /* CCLK = VCO / 1 */ +#define CCLK_DIV2 CSEL_DIV2 /* CCLK = VCO / 2 */ +#define CCLK_DIV4 CSEL_DIV4 /* CCLK = VCO / 4 */ +#define CCLK_DIV8 CSEL_DIV8 /* CCLK = VCO / 8 */ + +#endif diff --git a/arch/blackfin/mach-bf518/include/mach/cdefBF512.h b/arch/blackfin/mach-bf518/include/mach/cdefBF512.h new file mode 100644 index 00000000000..820c13c4daa --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/cdefBF512.h @@ -0,0 +1,46 @@ +/* + * File: include/asm-blackfin/mach-bf518/cdefbf512.h + * Based on: + * Author: + * + * Created: + * Description: system mmr register map + * + * Rev: + * + * Modified: + * + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _CDEF_BF512_H +#define _CDEF_BF512_H + +/* include all Core registers and bit definitions */ +#include "defBF512.h" + +/* include core specific register pointer definitions */ +#include <asm/cdef_LPBlackfin.h> + +/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF512 */ + +/* include cdefBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */ +#include "cdefBF51x_base.h" + +#endif /* _CDEF_BF512_H */ diff --git a/arch/blackfin/mach-bf518/include/mach/cdefBF514.h b/arch/blackfin/mach-bf518/include/mach/cdefBF514.h new file mode 100644 index 00000000000..9521e178fb2 --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/cdefBF514.h @@ -0,0 +1,48 @@ +/* + * File: include/asm-blackfin/mach-bf518/cdefbf514.h + * Based on: + * Author: + * + * Created: + * Description: system mmr register map + * + * Rev: + * + * Modified: + * + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _CDEF_BF514_H +#define _CDEF_BF514_H + +/* include all Core registers and bit definitions */ +#include "defBF514.h" + +/* include core specific register pointer definitions */ +#include <asm/cdef_LPBlackfin.h> + +/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF514 */ + +/* include cdefBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */ +#include "cdefBF51x_base.h" + +/* The following are the #defines needed by ADSP-BF514 that are not in the common header */ + +#endif /* _CDEF_BF514_H */ diff --git a/arch/blackfin/mach-bf518/include/mach/cdefBF516.h b/arch/blackfin/mach-bf518/include/mach/cdefBF516.h new file mode 100644 index 00000000000..17be34cbb7b --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/cdefBF516.h @@ -0,0 +1,48 @@ +/* + * File: include/asm-blackfin/mach-bf518/cdefbf516.h + * Based on: + * Author: + * + * Created: + * Description: system mmr register map + * + * Rev: + * + * Modified: + * + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _CDEF_BF516_H +#define _CDEF_BF516_H + +/* include all Core registers and bit definitions */ +#include "defBF516.h" + +/* include core specific register pointer definitions */ +#include <asm/cdef_LPBlackfin.h> + +/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF516 */ + +/* include cdefBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */ +#include "cdefBF51x_base.h" + +/* The following are the #defines needed by ADSP-BF516 that are not in the common header */ + +#endif /* _CDEF_BF516_H */ diff --git a/arch/blackfin/mach-bf518/include/mach/cdefBF518.h b/arch/blackfin/mach-bf518/include/mach/cdefBF518.h new file mode 100644 index 00000000000..5f978d48cc6 --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/cdefBF518.h @@ -0,0 +1,48 @@ +/* + * File: include/asm-blackfin/mach-bf518/cdefbf518.h + * Based on: + * Author: + * + * Created: + * Description: system mmr register map + * + * Rev: + * + * Modified: + * + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _CDEF_BF518_H +#define _CDEF_BF518_H + +/* include all Core registers and bit definitions */ +#include "defBF518.h" + +/* include core specific register pointer definitions */ +#include <asm/cdef_LPBlackfin.h> + +/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF518 */ + +/* include cdefBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */ +#include "cdefBF51x_base.h" + +/* The following are the #defines needed by ADSP-BF518 that are not in the common header */ + +#endif /* _CDEF_BF518_H */ diff --git a/arch/blackfin/mach-bf518/include/mach/cdefBF51x_base.h b/arch/blackfin/mach-bf518/include/mach/cdefBF51x_base.h new file mode 100644 index 00000000000..95d54e62597 --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/cdefBF51x_base.h @@ -0,0 +1,1204 @@ +/* + * File: include/asm-blackfin/mach-bf518/cdefBF51x_base.h + * Based on: + * Author: + * + * Created: + * Description: + * + * Rev: + * + * Modified: + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _CDEF_BF52X_H +#define _CDEF_BF52X_H + +#include <asm/system.h> +#include <asm/blackfin.h> + +#include "defBF51x_base.h" + +/* Include core specific register pointer definitions */ +#include <asm/cdef_LPBlackfin.h> + +/* ==== begin from cdefBF534.h ==== */ + +/* Clock and System Control (0xFFC00000 - 0xFFC000FF) */ +#define bfin_read_PLL_CTL() bfin_read16(PLL_CTL) +/* Writing to PLL_CTL initiates a PLL relock sequence. */ +static __inline__ void bfin_write_PLL_CTL(unsigned int val) +{ + unsigned long flags, iwr0, iwr1; + + if (val == bfin_read_PLL_CTL()) + return; + + local_irq_save(flags); + /* Enable the PLL Wakeup bit in SIC IWR */ + iwr0 = bfin_read32(SIC_IWR0); + iwr1 = bfin_read32(SIC_IWR1); + /* Only allow PPL Wakeup) */ + bfin_write32(SIC_IWR0, IWR_ENABLE(0)); + bfin_write32(SIC_IWR1, 0); + + bfin_write16(PLL_CTL, val); + SSYNC(); + asm("IDLE;"); + + bfin_write32(SIC_IWR0, iwr0); + bfin_write32(SIC_IWR1, iwr1); + local_irq_restore(flags); +} +#define bfin_read_PLL_DIV() bfin_read16(PLL_DIV) +#define bfin_write_PLL_DIV(val) bfin_write16(PLL_DIV, val) +#define bfin_read_VR_CTL() bfin_read16(VR_CTL) +/* Writing to VR_CTL initiates a PLL relock sequence. */ +static __inline__ void bfin_write_VR_CTL(unsigned int val) +{ + unsigned long flags, iwr0, iwr1; + + if (val == bfin_read_VR_CTL()) + return; + + local_irq_save(flags); + /* Enable the PLL Wakeup bit in SIC IWR */ + iwr0 = bfin_read32(SIC_IWR0); + iwr1 = bfin_read32(SIC_IWR1); + /* Only allow PPL Wakeup) */ + bfin_write32(SIC_IWR0, IWR_ENABLE(0)); + bfin_write32(SIC_IWR1, 0); + + bfin_write16(VR_CTL, val); + SSYNC(); + asm("IDLE;"); + + bfin_write32(SIC_IWR0, iwr0); + bfin_write32(SIC_IWR1, iwr1); + local_irq_restore(flags); +} +#define bfin_read_PLL_STAT() bfin_read16(PLL_STAT) +#define bfin_write_PLL_STAT(val) bfin_write16(PLL_STAT, val) +#define bfin_read_PLL_LOCKCNT() bfin_read16(PLL_LOCKCNT) +#define bfin_write_PLL_LOCKCNT(val) bfin_write16(PLL_LOCKCNT, val) +#define bfin_read_CHIPID() bfin_read32(CHIPID) +#define bfin_write_CHIPID(val) bfin_write32(CHIPID, val) + + +/* System Interrupt Controller (0xFFC00100 - 0xFFC001FF) */ +#define bfin_read_SWRST() bfin_read16(SWRST) +#define bfin_write_SWRST(val) bfin_write16(SWRST, val) +#define bfin_read_SYSCR() bfin_read16(SYSCR) +#define bfin_write_SYSCR(val) bfin_write16(SYSCR, val) + +#define bfin_read_SIC_RVECT() bfin_read32(SIC_RVECT) +#define bfin_write_SIC_RVECT(val) bfin_write32(SIC_RVECT, val) +#define bfin_read_SIC_IMASK0() bfin_read32(SIC_IMASK0) +#define bfin_write_SIC_IMASK0(val) bfin_write32(SIC_IMASK0, val) +#define bfin_read_SIC_IMASK(x) bfin_read32(SIC_IMASK0 + (x << 6)) +#define bfin_write_SIC_IMASK(x, val) bfin_write32((SIC_IMASK0 + (x << 6)), val) + +#define bfin_read_SIC_IAR0() bfin_read32(SIC_IAR0) +#define bfin_write_SIC_IAR0(val) bfin_write32(SIC_IAR0, val) +#define bfin_read_SIC_IAR1() bfin_read32(SIC_IAR1) +#define bfin_write_SIC_IAR1(val) bfin_write32(SIC_IAR1, val) +#define bfin_read_SIC_IAR2() bfin_read32(SIC_IAR2) +#define bfin_write_SIC_IAR2(val) bfin_write32(SIC_IAR2, val) +#define bfin_read_SIC_IAR3() bfin_read32(SIC_IAR3) +#define bfin_write_SIC_IAR3(val) bfin_write32(SIC_IAR3, val) + +#define bfin_read_SIC_ISR0() bfin_read32(SIC_ISR0) +#define bfin_write_SIC_ISR0(val) bfin_write32(SIC_ISR0, val) +#define bfin_read_SIC_ISR(x) bfin_read32(SIC_ISR0 + (x << 6)) +#define bfin_write_SIC_ISR(x, val) bfin_write32((SIC_ISR0 + (x << 6)), val) + +#define bfin_read_SIC_IWR0() bfin_read32(SIC_IWR0) +#define bfin_write_SIC_IWR0(val) bfin_write32(SIC_IWR0, val) +#define bfin_read_SIC_IWR(x) bfin_read32(SIC_IWR0 + (x << 6)) +#define bfin_write_SIC_IWR(x, val) bfin_write32((SIC_IWR0 + (x << 6)), val) + +/* SIC Additions to ADSP-BF51x (0xFFC0014C - 0xFFC00162) */ + +#define bfin_read_SIC_IMASK1() bfin_read32(SIC_IMASK1) +#define bfin_write_SIC_IMASK1(val) bfin_write32(SIC_IMASK1, val) +#define bfin_read_SIC_IAR4() bfin_read32(SIC_IAR4) +#define bfin_write_SIC_IAR4(val) bfin_write32(SIC_IAR4, val) +#define bfin_read_SIC_IAR5() bfin_read32(SIC_IAR5) +#define bfin_write_SIC_IAR5(val) bfin_write32(SIC_IAR5, val) +#define bfin_read_SIC_IAR6() bfin_read32(SIC_IAR6) +#define bfin_write_SIC_IAR6(val) bfin_write32(SIC_IAR6, val) +#define bfin_read_SIC_IAR7() bfin_read32(SIC_IAR7) +#define bfin_write_SIC_IAR7(val) bfin_write32(SIC_IAR7, val) +#define bfin_read_SIC_ISR1() bfin_read32(SIC_ISR1) +#define bfin_write_SIC_ISR1(val) bfin_write32(SIC_ISR1, val) +#define bfin_read_SIC_IWR1() bfin_read32(SIC_IWR1) +#define bfin_write_SIC_IWR1(val) bfin_write32(SIC_IWR1, val) + +/* Watchdog Timer (0xFFC00200 - 0xFFC002FF) */ +#define bfin_read_WDOG_CTL() bfin_read16(WDOG_CTL) +#define bfin_write_WDOG_CTL(val) bfin_write16(WDOG_CTL, val) +#define bfin_read_WDOG_CNT() bfin_read32(WDOG_CNT) +#define bfin_write_WDOG_CNT(val) bfin_write32(WDOG_CNT, val) +#define bfin_read_WDOG_STAT() bfin_read32(WDOG_STAT) +#define bfin_write_WDOG_STAT(val) bfin_write32(WDOG_STAT, val) + + +/* Real Time Clock (0xFFC00300 - 0xFFC003FF) */ +#define bfin_read_RTC_STAT() bfin_read32(RTC_STAT) +#define bfin_write_RTC_STAT(val) bfin_write32(RTC_STAT, val) +#define bfin_read_RTC_ICTL() bfin_read16(RTC_ICTL) +#define bfin_write_RTC_ICTL(val) bfin_write16(RTC_ICTL, val) +#define bfin_read_RTC_ISTAT() bfin_read16(RTC_ISTAT) +#define bfin_write_RTC_ISTAT(val) bfin_write16(RTC_ISTAT, val) +#define bfin_read_RTC_SWCNT() bfin_read16(RTC_SWCNT) +#define bfin_write_RTC_SWCNT(val) bfin_write16(RTC_SWCNT, val) +#define bfin_read_RTC_ALARM() bfin_read32(RTC_ALARM) +#define bfin_write_RTC_ALARM(val) bfin_write32(RTC_ALARM, val) +#define bfin_read_RTC_FAST() bfin_read16(RTC_FAST) +#define bfin_write_RTC_FAST(val) bfin_write16(RTC_FAST, val) +#define bfin_read_RTC_PREN() bfin_read16(RTC_PREN) +#define bfin_write_RTC_PREN(val) bfin_write16(RTC_PREN, val) + + +/* UART0 Controller (0xFFC00400 - 0xFFC004FF) */ +#define bfin_read_UART0_THR() bfin_read16(UART0_THR) +#define bfin_write_UART0_THR(val) bfin_write16(UART0_THR, val) +#define bfin_read_UART0_RBR() bfin_read16(UART0_RBR) +#define bfin_write_UART0_RBR(val) bfin_write16(UART0_RBR, val) +#define bfin_read_UART0_DLL() bfin_read16(UART0_DLL) +#define bfin_write_UART0_DLL(val) bfin_write16(UART0_DLL, val) +#define bfin_read_UART0_IER() bfin_read16(UART0_IER) +#define bfin_write_UART0_IER(val) bfin_write16(UART0_IER, val) +#define bfin_read_UART0_DLH() bfin_read16(UART0_DLH) +#define bfin_write_UART0_DLH(val) bfin_write16(UART0_DLH, val) +#define bfin_read_UART0_IIR() bfin_read16(UART0_IIR) +#define bfin_write_UART0_IIR(val) bfin_write16(UART0_IIR, val) +#define bfin_read_UART0_LCR() bfin_read16(UART0_LCR) +#define bfin_write_UART0_LCR(val) bfin_write16(UART0_LCR, val) +#define bfin_read_UART0_MCR() bfin_read16(UART0_MCR) +#define bfin_write_UART0_MCR(val) bfin_write16(UART0_MCR, val) +#define bfin_read_UART0_LSR() bfin_read16(UART0_LSR) +#define bfin_write_UART0_LSR(val) bfin_write16(UART0_LSR, val) +#define bfin_read_UART0_MSR() bfin_read16(UART0_MSR) +#define bfin_write_UART0_MSR(val) bfin_write16(UART0_MSR, val) +#define bfin_read_UART0_SCR() bfin_read16(UART0_SCR) +#define bfin_write_UART0_SCR(val) bfin_write16(UART0_SCR, val) +#define bfin_read_UART0_GCTL() bfin_read16(UART0_GCTL) +#define bfin_write_UART0_GCTL(val) bfin_write16(UART0_GCTL, val) + + +/* SPI Controller (0xFFC00500 - 0xFFC005FF) */ +#define bfin_read_SPI_CTL() bfin_read16(SPI_CTL) +#define bfin_write_SPI_CTL(val) bfin_write16(SPI_CTL, val) +#define bfin_read_SPI_FLG() bfin_read16(SPI_FLG) +#define bfin_write_SPI_FLG(val) bfin_write16(SPI_FLG, val) +#define bfin_read_SPI_STAT() bfin_read16(SPI_STAT) +#define bfin_write_SPI_STAT(val) bfin_write16(SPI_STAT, val) +#define bfin_read_SPI_TDBR() bfin_read16(SPI_TDBR) +#define bfin_write_SPI_TDBR(val) bfin_write16(SPI_TDBR, val) +#define bfin_read_SPI_RDBR() bfin_read16(SPI_RDBR) +#define bfin_write_SPI_RDBR(val) bfin_write16(SPI_RDBR, val) +#define bfin_read_SPI_BAUD() bfin_read16(SPI_BAUD) +#define bfin_write_SPI_BAUD(val) bfin_write16(SPI_BAUD, val) +#define bfin_read_SPI_SHADOW() bfin_read16(SPI_SHADOW) +#define bfin_write_SPI_SHADOW(val) bfin_write16(SPI_SHADOW, val) + + +/* TIMER0-7 Registers (0xFFC00600 - 0xFFC006FF) */ +#define bfin_read_TIMER0_CONFIG() bfin_read16(TIMER0_CONFIG) +#define bfin_write_TIMER0_CONFIG(val) bfin_write16(TIMER0_CONFIG, val) +#define bfin_read_TIMER0_COUNTER() bfin_read32(TIMER0_COUNTER) +#define bfin_write_TIMER0_COUNTER(val) bfin_write32(TIMER0_COUNTER, val) +#define bfin_read_TIMER0_PERIOD() bfin_read32(TIMER0_PERIOD) +#define bfin_write_TIMER0_PERIOD(val) bfin_write32(TIMER0_PERIOD, val) +#define bfin_read_TIMER0_WIDTH() bfin_read32(TIMER0_WIDTH) +#define bfin_write_TIMER0_WIDTH(val) bfin_write32(TIMER0_WIDTH, val) + +#define bfin_read_TIMER1_CONFIG() bfin_read16(TIMER1_CONFIG) +#define bfin_write_TIMER1_CONFIG(val) bfin_write16(TIMER1_CONFIG, val) +#define bfin_read_TIMER1_COUNTER() bfin_read32(TIMER1_COUNTER) +#define bfin_write_TIMER1_COUNTER(val) bfin_write32(TIMER1_COUNTER, val) +#define bfin_read_TIMER1_PERIOD() bfin_read32(TIMER1_PERIOD) +#define bfin_write_TIMER1_PERIOD(val) bfin_write32(TIMER1_PERIOD, val) +#define bfin_read_TIMER1_WIDTH() bfin_read32(TIMER1_WIDTH) +#define bfin_write_TIMER1_WIDTH(val) bfin_write32(TIMER1_WIDTH, val) + +#define bfin_read_TIMER2_CONFIG() bfin_read16(TIMER2_CONFIG) +#define bfin_write_TIMER2_CONFIG(val) bfin_write16(TIMER2_CONFIG, val) +#define bfin_read_TIMER2_COUNTER() bfin_read32(TIMER2_COUNTER) +#define bfin_write_TIMER2_COUNTER(val) bfin_write32(TIMER2_COUNTER, val) +#define bfin_read_TIMER2_PERIOD() bfin_read32(TIMER2_PERIOD) +#define bfin_write_TIMER2_PERIOD(val) bfin_write32(TIMER2_PERIOD, val) +#define bfin_read_TIMER2_WIDTH() bfin_read32(TIMER2_WIDTH) +#define bfin_write_TIMER2_WIDTH(val) bfin_write32(TIMER2_WIDTH, val) + +#define bfin_read_TIMER3_CONFIG() bfin_read16(TIMER3_CONFIG) +#define bfin_write_TIMER3_CONFIG(val) bfin_write16(TIMER3_CONFIG, val) +#define bfin_read_TIMER3_COUNTER() bfin_read32(TIMER3_COUNTER) +#define bfin_write_TIMER3_COUNTER(val) bfin_write32(TIMER3_COUNTER, val) +#define bfin_read_TIMER3_PERIOD() bfin_read32(TIMER3_PERIOD) +#define bfin_write_TIMER3_PERIOD(val) bfin_write32(TIMER3_PERIOD, val) +#define bfin_read_TIMER3_WIDTH() bfin_read32(TIMER3_WIDTH) +#define bfin_write_TIMER3_WIDTH(val) bfin_write32(TIMER3_WIDTH, val) + +#define bfin_read_TIMER4_CONFIG() bfin_read16(TIMER4_CONFIG) +#define bfin_write_TIMER4_CONFIG(val) bfin_write16(TIMER4_CONFIG, val) +#define bfin_read_TIMER4_COUNTER() bfin_read32(TIMER4_COUNTER) +#define bfin_write_TIMER4_COUNTER(val) bfin_write32(TIMER4_COUNTER, val) +#define bfin_read_TIMER4_PERIOD() bfin_read32(TIMER4_PERIOD) +#define bfin_write_TIMER4_PERIOD(val) bfin_write32(TIMER4_PERIOD, val) +#define bfin_read_TIMER4_WIDTH() bfin_read32(TIMER4_WIDTH) +#define bfin_write_TIMER4_WIDTH(val) bfin_write32(TIMER4_WIDTH, val) + +#define bfin_read_TIMER5_CONFIG() bfin_read16(TIMER5_CONFIG) +#define bfin_write_TIMER5_CONFIG(val) bfin_write16(TIMER5_CONFIG, val) +#define bfin_read_TIMER5_COUNTER() bfin_read32(TIMER5_COUNTER) +#define bfin_write_TIMER5_COUNTER(val) bfin_write32(TIMER5_COUNTER, val) +#define bfin_read_TIMER5_PERIOD() bfin_read32(TIMER5_PERIOD) +#define bfin_write_TIMER5_PERIOD(val) bfin_write32(TIMER5_PERIOD, val) +#define bfin_read_TIMER5_WIDTH() bfin_read32(TIMER5_WIDTH) +#define bfin_write_TIMER5_WIDTH(val) bfin_write32(TIMER5_WIDTH, val) + +#define bfin_read_TIMER6_CONFIG() bfin_read16(TIMER6_CONFIG) +#define bfin_write_TIMER6_CONFIG(val) bfin_write16(TIMER6_CONFIG, val) +#define bfin_read_TIMER6_COUNTER() bfin_read32(TIMER6_COUNTER) +#define bfin_write_TIMER6_COUNTER(val) bfin_write32(TIMER6_COUNTER, val) +#define bfin_read_TIMER6_PERIOD() bfin_read32(TIMER6_PERIOD) +#define bfin_write_TIMER6_PERIOD(val) bfin_write32(TIMER6_PERIOD, val) +#define bfin_read_TIMER6_WIDTH() bfin_read32(TIMER6_WIDTH) +#define bfin_write_TIMER6_WIDTH(val) bfin_write32(TIMER6_WIDTH, val) + +#define bfin_read_TIMER7_CONFIG() bfin_read16(TIMER7_CONFIG) +#define bfin_write_TIMER7_CONFIG(val) bfin_write16(TIMER7_CONFIG, val) +#define bfin_read_TIMER7_COUNTER() bfin_read32(TIMER7_COUNTER) +#define bfin_write_TIMER7_COUNTER(val) bfin_write32(TIMER7_COUNTER, val) +#define bfin_read_TIMER7_PERIOD() bfin_read32(TIMER7_PERIOD) +#define bfin_write_TIMER7_PERIOD(val) bfin_write32(TIMER7_PERIOD, val) +#define bfin_read_TIMER7_WIDTH() bfin_read32(TIMER7_WIDTH) +#define bfin_write_TIMER7_WIDTH(val) bfin_write32(TIMER7_WIDTH, val) + +#define bfin_read_TIMER_ENABLE() bfin_read16(TIMER_ENABLE) +#define bfin_write_TIMER_ENABLE(val) bfin_write16(TIMER_ENABLE, val) +#define bfin_read_TIMER_DISABLE() bfin_read16(TIMER_DISABLE) +#define bfin_write_TIMER_DISABLE(val) bfin_write16(TIMER_DISABLE, val) +#define bfin_read_TIMER_STATUS() bfin_read32(TIMER_STATUS) +#define bfin_write_TIMER_STATUS(val) bfin_write32(TIMER_STATUS, val) + + +/* General Purpose I/O Port F (0xFFC00700 - 0xFFC007FF) */ +#define bfin_read_PORTFIO() bfin_read16(PORTFIO) +#define bfin_write_PORTFIO(val) bfin_write16(PORTFIO, val) +#define bfin_read_PORTFIO_CLEAR() bfin_read16(PORTFIO_CLEAR) +#define bfin_write_PORTFIO_CLEAR(val) bfin_write16(PORTFIO_CLEAR, val) +#define bfin_read_PORTFIO_SET() bfin_read16(PORTFIO_SET) +#define bfin_write_PORTFIO_SET(val) bfin_write16(PORTFIO_SET, val) +#define bfin_read_PORTFIO_TOGGLE() bfin_read16(PORTFIO_TOGGLE) +#define bfin_write_PORTFIO_TOGGLE(val) bfin_write16(PORTFIO_TOGGLE, val) +#define bfin_read_PORTFIO_MASKA() bfin_read16(PORTFIO_MASKA) +#define bfin_write_PORTFIO_MASKA(val) bfin_write16(PORTFIO_MASKA, val) +#define bfin_read_PORTFIO_MASKA_CLEAR() bfin_read16(PORTFIO_MASKA_CLEAR) +#define bfin_write_PORTFIO_MASKA_CLEAR(val) bfin_write16(PORTFIO_MASKA_CLEAR, val) +#define bfin_read_PORTFIO_MASKA_SET() bfin_read16(PORTFIO_MASKA_SET) +#define bfin_write_PORTFIO_MASKA_SET(val) bfin_write16(PORTFIO_MASKA_SET, val) +#define bfin_read_PORTFIO_MASKA_TOGGLE() bfin_read16(PORTFIO_MASKA_TOGGLE) +#define bfin_write_PORTFIO_MASKA_TOGGLE(val) bfin_write16(PORTFIO_MASKA_TOGGLE, val) +#define bfin_read_PORTFIO_MASKB() bfin_read16(PORTFIO_MASKB) +#define bfin_write_PORTFIO_MASKB(val) bfin_write16(PORTFIO_MASKB, val) +#define bfin_read_PORTFIO_MASKB_CLEAR() bfin_read16(PORTFIO_MASKB_CLEAR) +#define bfin_write_PORTFIO_MASKB_CLEAR(val) bfin_write16(PORTFIO_MASKB_CLEAR, val) +#define bfin_read_PORTFIO_MASKB_SET() bfin_read16(PORTFIO_MASKB_SET) +#define bfin_write_PORTFIO_MASKB_SET(val) bfin_write16(PORTFIO_MASKB_SET, val) +#define bfin_read_PORTFIO_MASKB_TOGGLE() bfin_read16(PORTFIO_MASKB_TOGGLE) +#define bfin_write_PORTFIO_MASKB_TOGGLE(val) bfin_write16(PORTFIO_MASKB_TOGGLE, val) +#define bfin_read_PORTFIO_DIR() bfin_read16(PORTFIO_DIR) +#define bfin_write_PORTFIO_DIR(val) bfin_write16(PORTFIO_DIR, val) +#define bfin_read_PORTFIO_POLAR() bfin_read16(PORTFIO_POLAR) +#define bfin_write_PORTFIO_POLAR(val) bfin_write16(PORTFIO_POLAR, val) +#define bfin_read_PORTFIO_EDGE() bfin_read16(PORTFIO_EDGE) +#define bfin_write_PORTFIO_EDGE(val) bfin_write16(PORTFIO_EDGE, val) +#define bfin_read_PORTFIO_BOTH() bfin_read16(PORTFIO_BOTH) +#define bfin_write_PORTFIO_BOTH(val) bfin_write16(PORTFIO_BOTH, val) +#define bfin_read_PORTFIO_INEN() bfin_read16(PORTFIO_INEN) +#define bfin_write_PORTFIO_INEN(val) bfin_write16(PORTFIO_INEN, val) + + +/* SPORT0 Controller (0xFFC00800 - 0xFFC008FF) */ +#define bfin_read_SPORT0_TCR1() bfin_read16(SPORT0_TCR1) +#define bfin_write_SPORT0_TCR1(val) bfin_write16(SPORT0_TCR1, val) +#define bfin_read_SPORT0_TCR2() bfin_read16(SPORT0_TCR2) +#define bfin_write_SPORT0_TCR2(val) bfin_write16(SPORT0_TCR2, val) +#define bfin_read_SPORT0_TCLKDIV() bfin_read16(SPORT0_TCLKDIV) +#define bfin_write_SPORT0_TCLKDIV(val) bfin_write16(SPORT0_TCLKDIV, val) +#define bfin_read_SPORT0_TFSDIV() bfin_read16(SPORT0_TFSDIV) +#define bfin_write_SPORT0_TFSDIV(val) bfin_write16(SPORT0_TFSDIV, val) +#define bfin_read_SPORT0_TX() bfin_read32(SPORT0_TX) +#define bfin_write_SPORT0_TX(val) bfin_write32(SPORT0_TX, val) +#define bfin_read_SPORT0_RX() bfin_read32(SPORT0_RX) +#define bfin_write_SPORT0_RX(val) bfin_write32(SPORT0_RX, val) +#define bfin_read_SPORT0_TX32() bfin_read32(SPORT0_TX32) +#define bfin_write_SPORT0_TX32(val) bfin_write32(SPORT0_TX32, val) +#define bfin_read_SPORT0_RX32() bfin_read32(SPORT0_RX32) +#define bfin_write_SPORT0_RX32(val) bfin_write32(SPORT0_RX32, val) +#define bfin_read_SPORT0_TX16() bfin_read16(SPORT0_TX16) +#define bfin_write_SPORT0_TX16(val) bfin_write16(SPORT0_TX16, val) +#define bfin_read_SPORT0_RX16() bfin_read16(SPORT0_RX16) +#define bfin_write_SPORT0_RX16(val) bfin_write16(SPORT0_RX16, val) +#define bfin_read_SPORT0_RCR1() bfin_read16(SPORT0_RCR1) +#define bfin_write_SPORT0_RCR1(val) bfin_write16(SPORT0_RCR1, val) +#define bfin_read_SPORT0_RCR2() bfin_read16(SPORT0_RCR2) +#define bfin_write_SPORT0_RCR2(val) bfin_write16(SPORT0_RCR2, val) +#define bfin_read_SPORT0_RCLKDIV() bfin_read16(SPORT0_RCLKDIV) +#define bfin_write_SPORT0_RCLKDIV(val) bfin_write16(SPORT0_RCLKDIV, val) +#define bfin_read_SPORT0_RFSDIV() bfin_read16(SPORT0_RFSDIV) +#define bfin_write_SPORT0_RFSDIV(val) bfin_write16(SPORT0_RFSDIV, val) +#define bfin_read_SPORT0_STAT() bfin_read16(SPORT0_STAT) +#define bfin_write_SPORT0_STAT(val) bfin_write16(SPORT0_STAT, val) +#define bfin_read_SPORT0_CHNL() bfin_read16(SPORT0_CHNL) +#define bfin_write_SPORT0_CHNL(val) bfin_write16(SPORT0_CHNL, val) +#define bfin_read_SPORT0_MCMC1() bfin_read16(SPORT0_MCMC1) +#define bfin_write_SPORT0_MCMC1(val) bfin_write16(SPORT0_MCMC1, val) +#define bfin_read_SPORT0_MCMC2() bfin_read16(SPORT0_MCMC2) +#define bfin_write_SPORT0_MCMC2(val) bfin_write16(SPORT0_MCMC2, val) +#define bfin_read_SPORT0_MTCS0() bfin_read32(SPORT0_MTCS0) +#define bfin_write_SPORT0_MTCS0(val) bfin_write32(SPORT0_MTCS0, val) +#define bfin_read_SPORT0_MTCS1() bfin_read32(SPORT0_MTCS1) +#define bfin_write_SPORT0_MTCS1(val) bfin_write32(SPORT0_MTCS1, val) +#define bfin_read_SPORT0_MTCS2() bfin_read32(SPORT0_MTCS2) +#define bfin_write_SPORT0_MTCS2(val) bfin_write32(SPORT0_MTCS2, val) +#define bfin_read_SPORT0_MTCS3() bfin_read32(SPORT0_MTCS3) +#define bfin_write_SPORT0_MTCS3(val) bfin_write32(SPORT0_MTCS3, val) +#define bfin_read_SPORT0_MRCS0() bfin_read32(SPORT0_MRCS0) +#define bfin_write_SPORT0_MRCS0(val) bfin_write32(SPORT0_MRCS0, val) +#define bfin_read_SPORT0_MRCS1() bfin_read32(SPORT0_MRCS1) +#define bfin_write_SPORT0_MRCS1(val) bfin_write32(SPORT0_MRCS1, val) +#define bfin_read_SPORT0_MRCS2() bfin_read32(SPORT0_MRCS2) +#define bfin_write_SPORT0_MRCS2(val) bfin_write32(SPORT0_MRCS2, val) +#define bfin_read_SPORT0_MRCS3() bfin_read32(SPORT0_MRCS3) +#define bfin_write_SPORT0_MRCS3(val) bfin_write32(SPORT0_MRCS3, val) + + +/* SPORT1 Controller (0xFFC00900 - 0xFFC009FF) */ +#define bfin_read_SPORT1_TCR1() bfin_read16(SPORT1_TCR1) +#define bfin_write_SPORT1_TCR1(val) bfin_write16(SPORT1_TCR1, val) +#define bfin_read_SPORT1_TCR2() bfin_read16(SPORT1_TCR2) +#define bfin_write_SPORT1_TCR2(val) bfin_write16(SPORT1_TCR2, val) +#define bfin_read_SPORT1_TCLKDIV() bfin_read16(SPORT1_TCLKDIV) +#define bfin_write_SPORT1_TCLKDIV(val) bfin_write16(SPORT1_TCLKDIV, val) +#define bfin_read_SPORT1_TFSDIV() bfin_read16(SPORT1_TFSDIV) +#define bfin_write_SPORT1_TFSDIV(val) bfin_write16(SPORT1_TFSDIV, val) +#define bfin_read_SPORT1_TX() bfin_read32(SPORT1_TX) +#define bfin_write_SPORT1_TX(val) bfin_write32(SPORT1_TX, val) +#define bfin_read_SPORT1_RX() bfin_read32(SPORT1_RX) +#define bfin_write_SPORT1_RX(val) bfin_write32(SPORT1_RX, val) +#define bfin_read_SPORT1_TX32() bfin_read32(SPORT1_TX32) +#define bfin_write_SPORT1_TX32(val) bfin_write32(SPORT1_TX32, val) +#define bfin_read_SPORT1_RX32() bfin_read32(SPORT1_RX32) +#define bfin_write_SPORT1_RX32(val) bfin_write32(SPORT1_RX32, val) +#define bfin_read_SPORT1_TX16() bfin_read16(SPORT1_TX16) +#define bfin_write_SPORT1_TX16(val) bfin_write16(SPORT1_TX16, val) +#define bfin_read_SPORT1_RX16() bfin_read16(SPORT1_RX16) +#define bfin_write_SPORT1_RX16(val) bfin_write16(SPORT1_RX16, val) +#define bfin_read_SPORT1_RCR1() bfin_read16(SPORT1_RCR1) +#define bfin_write_SPORT1_RCR1(val) bfin_write16(SPORT1_RCR1, val) +#define bfin_read_SPORT1_RCR2() bfin_read16(SPORT1_RCR2) +#define bfin_write_SPORT1_RCR2(val) bfin_write16(SPORT1_RCR2, val) +#define bfin_read_SPORT1_RCLKDIV() bfin_read16(SPORT1_RCLKDIV) +#define bfin_write_SPORT1_RCLKDIV(val) bfin_write16(SPORT1_RCLKDIV, val) +#define bfin_read_SPORT1_RFSDIV() bfin_read16(SPORT1_RFSDIV) +#define bfin_write_SPORT1_RFSDIV(val) bfin_write16(SPORT1_RFSDIV, val) +#define bfin_read_SPORT1_STAT() bfin_read16(SPORT1_STAT) +#define bfin_write_SPORT1_STAT(val) bfin_write16(SPORT1_STAT, val) +#define bfin_read_SPORT1_CHNL() bfin_read16(SPORT1_CHNL) +#define bfin_write_SPORT1_CHNL(val) bfin_write16(SPORT1_CHNL, val) +#define bfin_read_SPORT1_MCMC1() bfin_read16(SPORT1_MCMC1) +#define bfin_write_SPORT1_MCMC1(val) bfin_write16(SPORT1_MCMC1, val) +#define bfin_read_SPORT1_MCMC2() bfin_read16(SPORT1_MCMC2) +#define bfin_write_SPORT1_MCMC2(val) bfin_write16(SPORT1_MCMC2, val) +#define bfin_read_SPORT1_MTCS0() bfin_read32(SPORT1_MTCS0) +#define bfin_write_SPORT1_MTCS0(val) bfin_write32(SPORT1_MTCS0, val) +#define bfin_read_SPORT1_MTCS1() bfin_read32(SPORT1_MTCS1) +#define bfin_write_SPORT1_MTCS1(val) bfin_write32(SPORT1_MTCS1, val) +#define bfin_read_SPORT1_MTCS2() bfin_read32(SPORT1_MTCS2) +#define bfin_write_SPORT1_MTCS2(val) bfin_write32(SPORT1_MTCS2, val) +#define bfin_read_SPORT1_MTCS3() bfin_read32(SPORT1_MTCS3) +#define bfin_write_SPORT1_MTCS3(val) bfin_write32(SPORT1_MTCS3, val) +#define bfin_read_SPORT1_MRCS0() bfin_read32(SPORT1_MRCS0) +#define bfin_write_SPORT1_MRCS0(val) bfin_write32(SPORT1_MRCS0, val) +#define bfin_read_SPORT1_MRCS1() bfin_read32(SPORT1_MRCS1) +#define bfin_write_SPORT1_MRCS1(val) bfin_write32(SPORT1_MRCS1, val) +#define bfin_read_SPORT1_MRCS2() bfin_read32(SPORT1_MRCS2) +#define bfin_write_SPORT1_MRCS2(val) bfin_write32(SPORT1_MRCS2, val) +#define bfin_read_SPORT1_MRCS3() bfin_read32(SPORT1_MRCS3) +#define bfin_write_SPORT1_MRCS3(val) bfin_write32(SPORT1_MRCS3, val) + + +/* External Bus Interface Unit (0xFFC00A00 - 0xFFC00AFF) */ +#define bfin_read_EBIU_AMGCTL() bfin_read16(EBIU_AMGCTL) +#define bfin_write_EBIU_AMGCTL(val) bfin_write16(EBIU_AMGCTL, val) +#define bfin_read_EBIU_AMBCTL0() bfin_read32(EBIU_AMBCTL0) +#define bfin_write_EBIU_AMBCTL0(val) bfin_write32(EBIU_AMBCTL0, val) +#define bfin_read_EBIU_AMBCTL1() bfin_read32(EBIU_AMBCTL1) +#define bfin_write_EBIU_AMBCTL1(val) bfin_write32(EBIU_AMBCTL1, val) +#define bfin_read_EBIU_SDGCTL() bfin_read32(EBIU_SDGCTL) +#define bfin_write_EBIU_SDGCTL(val) bfin_write32(EBIU_SDGCTL, val) +#define bfin_read_EBIU_SDBCTL() bfin_read16(EBIU_SDBCTL) +#define bfin_write_EBIU_SDBCTL(val) bfin_write16(EBIU_SDBCTL, val) +#define bfin_read_EBIU_SDRRC() bfin_read16(EBIU_SDRRC) +#define bfin_write_EBIU_SDRRC(val) bfin_write16(EBIU_SDRRC, val) +#define bfin_read_EBIU_SDSTAT() bfin_read16(EBIU_SDSTAT) +#define bfin_write_EBIU_SDSTAT(val) bfin_write16(EBIU_SDSTAT, val) + + +/* DMA Traffic Control Registers */ +#define bfin_read_DMA_TC_PER() bfin_read16(DMA_TC_PER) +#define bfin_write_DMA_TC_PER(val) bfin_write16(DMA_TC_PER, val) +#define bfin_read_DMA_TC_CNT() bfin_read16(DMA_TC_CNT) +#define bfin_write_DMA_TC_CNT(val) bfin_write16(DMA_TC_CNT, val) + +/* Alternate deprecated register names (below) provided for backwards code compatibility */ +#define bfin_read_DMA_TCPER() bfin_read16(DMA_TCPER) +#define bfin_write_DMA_TCPER(val) bfin_write16(DMA_TCPER, val) +#define bfin_read_DMA_TCCNT() bfin_read16(DMA_TCCNT) +#define bfin_write_DMA_TCCNT(val) bfin_write16(DMA_TCCNT, val) + +/* DMA Controller */ +#define bfin_read_DMA0_CONFIG() bfin_read16(DMA0_CONFIG) +#define bfin_write_DMA0_CONFIG(val) bfin_write16(DMA0_CONFIG, val) +#define bfin_read_DMA0_NEXT_DESC_PTR() bfin_read32(DMA0_NEXT_DESC_PTR) +#define bfin_write_DMA0_NEXT_DESC_PTR(val) bfin_write32(DMA0_NEXT_DESC_PTR, val) +#define bfin_read_DMA0_START_ADDR() bfin_read32(DMA0_START_ADDR) +#define bfin_write_DMA0_START_ADDR(val) bfin_write32(DMA0_START_ADDR, val) +#define bfin_read_DMA0_X_COUNT() bfin_read16(DMA0_X_COUNT) +#define bfin_write_DMA0_X_COUNT(val) bfin_write16(DMA0_X_COUNT, val) +#define bfin_read_DMA0_Y_COUNT() bfin_read16(DMA0_Y_COUNT) +#define bfin_write_DMA0_Y_COUNT(val) bfin_write16(DMA0_Y_COUNT, val) +#define bfin_read_DMA0_X_MODIFY() bfin_read16(DMA0_X_MODIFY) +#define bfin_write_DMA0_X_MODIFY(val) bfin_write16(DMA0_X_MODIFY, val) +#define bfin_read_DMA0_Y_MODIFY() bfin_read16(DMA0_Y_MODIFY) +#define bfin_write_DMA0_Y_MODIFY(val) bfin_write16(DMA0_Y_MODIFY, val) +#define bfin_read_DMA0_CURR_DESC_PTR() bfin_read32(DMA0_CURR_DESC_PTR) +#define bfin_write_DMA0_CURR_DESC_PTR(val) bfin_write32(DMA0_CURR_DESC_PTR, val) +#define bfin_read_DMA0_CURR_ADDR() bfin_read32(DMA0_CURR_ADDR) +#define bfin_write_DMA0_CURR_ADDR(val) bfin_write32(DMA0_CURR_ADDR, val) +#define bfin_read_DMA0_CURR_X_COUNT() bfin_read16(DMA0_CURR_X_COUNT) +#define bfin_write_DMA0_CURR_X_COUNT(val) bfin_write16(DMA0_CURR_X_COUNT, val) +#define bfin_read_DMA0_CURR_Y_COUNT() bfin_read16(DMA0_CURR_Y_COUNT) +#define bfin_write_DMA0_CURR_Y_COUNT(val) bfin_write16(DMA0_CURR_Y_COUNT, val) +#define bfin_read_DMA0_IRQ_STATUS() bfin_read16(DMA0_IRQ_STATUS) +#define bfin_write_DMA0_IRQ_STATUS(val) bfin_write16(DMA0_IRQ_STATUS, val) +#define bfin_read_DMA0_PERIPHERAL_MAP() bfin_read16(DMA0_PERIPHERAL_MAP) +#define bfin_write_DMA0_PERIPHERAL_MAP(val) bfin_write16(DMA0_PERIPHERAL_MAP, val) + +#define bfin_read_DMA1_CONFIG() bfin_read16(DMA1_CONFIG) +#define bfin_write_DMA1_CONFIG(val) bfin_write16(DMA1_CONFIG, val) +#define bfin_read_DMA1_NEXT_DESC_PTR() bfin_read32(DMA1_NEXT_DESC_PTR) +#define bfin_write_DMA1_NEXT_DESC_PTR(val) bfin_write32(DMA1_NEXT_DESC_PTR, val) +#define bfin_read_DMA1_START_ADDR() bfin_read32(DMA1_START_ADDR) +#define bfin_write_DMA1_START_ADDR(val) bfin_write32(DMA1_START_ADDR, val) +#define bfin_read_DMA1_X_COUNT() bfin_read16(DMA1_X_COUNT) +#define bfin_write_DMA1_X_COUNT(val) bfin_write16(DMA1_X_COUNT, val) +#define bfin_read_DMA1_Y_COUNT() bfin_read16(DMA1_Y_COUNT) +#define bfin_write_DMA1_Y_COUNT(val) bfin_write16(DMA1_Y_COUNT, val) +#define bfin_read_DMA1_X_MODIFY() bfin_read16(DMA1_X_MODIFY) +#define bfin_write_DMA1_X_MODIFY(val) bfin_write16(DMA1_X_MODIFY, val) +#define bfin_read_DMA1_Y_MODIFY() bfin_read16(DMA1_Y_MODIFY) +#define bfin_write_DMA1_Y_MODIFY(val) bfin_write16(DMA1_Y_MODIFY, val) +#define bfin_read_DMA1_CURR_DESC_PTR() bfin_read32(DMA1_CURR_DESC_PTR) +#define bfin_write_DMA1_CURR_DESC_PTR(val) bfin_write32(DMA1_CURR_DESC_PTR, val) +#define bfin_read_DMA1_CURR_ADDR() bfin_read32(DMA1_CURR_ADDR) +#define bfin_write_DMA1_CURR_ADDR(val) bfin_write32(DMA1_CURR_ADDR, val) +#define bfin_read_DMA1_CURR_X_COUNT() bfin_read16(DMA1_CURR_X_COUNT) +#define bfin_write_DMA1_CURR_X_COUNT(val) bfin_write16(DMA1_CURR_X_COUNT, val) +#define bfin_read_DMA1_CURR_Y_COUNT() bfin_read16(DMA1_CURR_Y_COUNT) +#define bfin_write_DMA1_CURR_Y_COUNT(val) bfin_write16(DMA1_CURR_Y_COUNT, val) +#define bfin_read_DMA1_IRQ_STATUS() bfin_read16(DMA1_IRQ_STATUS) +#define bfin_write_DMA1_IRQ_STATUS(val) bfin_write16(DMA1_IRQ_STATUS, val) +#define bfin_read_DMA1_PERIPHERAL_MAP() bfin_read16(DMA1_PERIPHERAL_MAP) +#define bfin_write_DMA1_PERIPHERAL_MAP(val) bfin_write16(DMA1_PERIPHERAL_MAP, val) + +#define bfin_read_DMA2_CONFIG() bfin_read16(DMA2_CONFIG) +#define bfin_write_DMA2_CONFIG(val) bfin_write16(DMA2_CONFIG, val) +#define bfin_read_DMA2_NEXT_DESC_PTR() bfin_read32(DMA2_NEXT_DESC_PTR) +#define bfin_write_DMA2_NEXT_DESC_PTR(val) bfin_write32(DMA2_NEXT_DESC_PTR, val) +#define bfin_read_DMA2_START_ADDR() bfin_read32(DMA2_START_ADDR) +#define bfin_write_DMA2_START_ADDR(val) bfin_write32(DMA2_START_ADDR, val) +#define bfin_read_DMA2_X_COUNT() bfin_read16(DMA2_X_COUNT) +#define bfin_write_DMA2_X_COUNT(val) bfin_write16(DMA2_X_COUNT, val) +#define bfin_read_DMA2_Y_COUNT() bfin_read16(DMA2_Y_COUNT) +#define bfin_write_DMA2_Y_COUNT(val) bfin_write16(DMA2_Y_COUNT, val) +#define bfin_read_DMA2_X_MODIFY() bfin_read16(DMA2_X_MODIFY) +#define bfin_write_DMA2_X_MODIFY(val) bfin_write16(DMA2_X_MODIFY, val) +#define bfin_read_DMA2_Y_MODIFY() bfin_read16(DMA2_Y_MODIFY) +#define bfin_write_DMA2_Y_MODIFY(val) bfin_write16(DMA2_Y_MODIFY, val) +#define bfin_read_DMA2_CURR_DESC_PTR() bfin_read32(DMA2_CURR_DESC_PTR) +#define bfin_write_DMA2_CURR_DESC_PTR(val) bfin_write32(DMA2_CURR_DESC_PTR, val) +#define bfin_read_DMA2_CURR_ADDR() bfin_read32(DMA2_CURR_ADDR) +#define bfin_write_DMA2_CURR_ADDR(val) bfin_write32(DMA2_CURR_ADDR, val) +#define bfin_read_DMA2_CURR_X_COUNT() bfin_read16(DMA2_CURR_X_COUNT) +#define bfin_write_DMA2_CURR_X_COUNT(val) bfin_write16(DMA2_CURR_X_COUNT, val) +#define bfin_read_DMA2_CURR_Y_COUNT() bfin_read16(DMA2_CURR_Y_COUNT) +#define bfin_write_DMA2_CURR_Y_COUNT(val) bfin_write16(DMA2_CURR_Y_COUNT, val) +#define bfin_read_DMA2_IRQ_STATUS() bfin_read16(DMA2_IRQ_STATUS) +#define bfin_write_DMA2_IRQ_STATUS(val) bfin_write16(DMA2_IRQ_STATUS, val) +#define bfin_read_DMA2_PERIPHERAL_MAP() bfin_read16(DMA2_PERIPHERAL_MAP) +#define bfin_write_DMA2_PERIPHERAL_MAP(val) bfin_write16(DMA2_PERIPHERAL_MAP, val) + +#define bfin_read_DMA3_CONFIG() bfin_read16(DMA3_CONFIG) +#define bfin_write_DMA3_CONFIG(val) bfin_write16(DMA3_CONFIG, val) +#define bfin_read_DMA3_NEXT_DESC_PTR() bfin_read32(DMA3_NEXT_DESC_PTR) +#define bfin_write_DMA3_NEXT_DESC_PTR(val) bfin_write32(DMA3_NEXT_DESC_PTR, val) +#define bfin_read_DMA3_START_ADDR() bfin_read32(DMA3_START_ADDR) +#define bfin_write_DMA3_START_ADDR(val) bfin_write32(DMA3_START_ADDR, val) +#define bfin_read_DMA3_X_COUNT() bfin_read16(DMA3_X_COUNT) +#define bfin_write_DMA3_X_COUNT(val) bfin_write16(DMA3_X_COUNT, val) +#define bfin_read_DMA3_Y_COUNT() bfin_read16(DMA3_Y_COUNT) +#define bfin_write_DMA3_Y_COUNT(val) bfin_write16(DMA3_Y_COUNT, val) +#define bfin_read_DMA3_X_MODIFY() bfin_read16(DMA3_X_MODIFY) +#define bfin_write_DMA3_X_MODIFY(val) bfin_write16(DMA3_X_MODIFY, val) +#define bfin_read_DMA3_Y_MODIFY() bfin_read16(DMA3_Y_MODIFY) +#define bfin_write_DMA3_Y_MODIFY(val) bfin_write16(DMA3_Y_MODIFY, val) +#define bfin_read_DMA3_CURR_DESC_PTR() bfin_read32(DMA3_CURR_DESC_PTR) +#define bfin_write_DMA3_CURR_DESC_PTR(val) bfin_write32(DMA3_CURR_DESC_PTR, val) +#define bfin_read_DMA3_CURR_ADDR() bfin_read32(DMA3_CURR_ADDR) +#define bfin_write_DMA3_CURR_ADDR(val) bfin_write32(DMA3_CURR_ADDR, val) +#define bfin_read_DMA3_CURR_X_COUNT() bfin_read16(DMA3_CURR_X_COUNT) +#define bfin_write_DMA3_CURR_X_COUNT(val) bfin_write16(DMA3_CURR_X_COUNT, val) +#define bfin_read_DMA3_CURR_Y_COUNT() bfin_read16(DMA3_CURR_Y_COUNT) +#define bfin_write_DMA3_CURR_Y_COUNT(val) bfin_write16(DMA3_CURR_Y_COUNT, val) +#define bfin_read_DMA3_IRQ_STATUS() bfin_read16(DMA3_IRQ_STATUS) +#define bfin_write_DMA3_IRQ_STATUS(val) bfin_write16(DMA3_IRQ_STATUS, val) +#define bfin_read_DMA3_PERIPHERAL_MAP() bfin_read16(DMA3_PERIPHERAL_MAP) +#define bfin_write_DMA3_PERIPHERAL_MAP(val) bfin_write16(DMA3_PERIPHERAL_MAP, val) + +#define bfin_read_DMA4_CONFIG() bfin_read16(DMA4_CONFIG) +#define bfin_write_DMA4_CONFIG(val) bfin_write16(DMA4_CONFIG, val) +#define bfin_read_DMA4_NEXT_DESC_PTR() bfin_read32(DMA4_NEXT_DESC_PTR) +#define bfin_write_DMA4_NEXT_DESC_PTR(val) bfin_write32(DMA4_NEXT_DESC_PTR, val) +#define bfin_read_DMA4_START_ADDR() bfin_read32(DMA4_START_ADDR) +#define bfin_write_DMA4_START_ADDR(val) bfin_write32(DMA4_START_ADDR, val) +#define bfin_read_DMA4_X_COUNT() bfin_read16(DMA4_X_COUNT) +#define bfin_write_DMA4_X_COUNT(val) bfin_write16(DMA4_X_COUNT, val) +#define bfin_read_DMA4_Y_COUNT() bfin_read16(DMA4_Y_COUNT) +#define bfin_write_DMA4_Y_COUNT(val) bfin_write16(DMA4_Y_COUNT, val) +#define bfin_read_DMA4_X_MODIFY() bfin_read16(DMA4_X_MODIFY) +#define bfin_write_DMA4_X_MODIFY(val) bfin_write16(DMA4_X_MODIFY, val) +#define bfin_read_DMA4_Y_MODIFY() bfin_read16(DMA4_Y_MODIFY) +#define bfin_write_DMA4_Y_MODIFY(val) bfin_write16(DMA4_Y_MODIFY, val) +#define bfin_read_DMA4_CURR_DESC_PTR() bfin_read32(DMA4_CURR_DESC_PTR) +#define bfin_write_DMA4_CURR_DESC_PTR(val) bfin_write32(DMA4_CURR_DESC_PTR, val) +#define bfin_read_DMA4_CURR_ADDR() bfin_read32(DMA4_CURR_ADDR) +#define bfin_write_DMA4_CURR_ADDR(val) bfin_write32(DMA4_CURR_ADDR, val) +#define bfin_read_DMA4_CURR_X_COUNT() bfin_read16(DMA4_CURR_X_COUNT) +#define bfin_write_DMA4_CURR_X_COUNT(val) bfin_write16(DMA4_CURR_X_COUNT, val) +#define bfin_read_DMA4_CURR_Y_COUNT() bfin_read16(DMA4_CURR_Y_COUNT) +#define bfin_write_DMA4_CURR_Y_COUNT(val) bfin_write16(DMA4_CURR_Y_COUNT, val) +#define bfin_read_DMA4_IRQ_STATUS() bfin_read16(DMA4_IRQ_STATUS) +#define bfin_write_DMA4_IRQ_STATUS(val) bfin_write16(DMA4_IRQ_STATUS, val) +#define bfin_read_DMA4_PERIPHERAL_MAP() bfin_read16(DMA4_PERIPHERAL_MAP) +#define bfin_write_DMA4_PERIPHERAL_MAP(val) bfin_write16(DMA4_PERIPHERAL_MAP, val) + +#define bfin_read_DMA5_CONFIG() bfin_read16(DMA5_CONFIG) +#define bfin_write_DMA5_CONFIG(val) bfin_write16(DMA5_CONFIG, val) +#define bfin_read_DMA5_NEXT_DESC_PTR() bfin_read32(DMA5_NEXT_DESC_PTR) +#define bfin_write_DMA5_NEXT_DESC_PTR(val) bfin_write32(DMA5_NEXT_DESC_PTR, val) +#define bfin_read_DMA5_START_ADDR() bfin_read32(DMA5_START_ADDR) +#define bfin_write_DMA5_START_ADDR(val) bfin_write32(DMA5_START_ADDR, val) +#define bfin_read_DMA5_X_COUNT() bfin_read16(DMA5_X_COUNT) +#define bfin_write_DMA5_X_COUNT(val) bfin_write16(DMA5_X_COUNT, val) +#define bfin_read_DMA5_Y_COUNT() bfin_read16(DMA5_Y_COUNT) +#define bfin_write_DMA5_Y_COUNT(val) bfin_write16(DMA5_Y_COUNT, val) +#define bfin_read_DMA5_X_MODIFY() bfin_read16(DMA5_X_MODIFY) +#define bfin_write_DMA5_X_MODIFY(val) bfin_write16(DMA5_X_MODIFY, val) +#define bfin_read_DMA5_Y_MODIFY() bfin_read16(DMA5_Y_MODIFY) +#define bfin_write_DMA5_Y_MODIFY(val) bfin_write16(DMA5_Y_MODIFY, val) +#define bfin_read_DMA5_CURR_DESC_PTR() bfin_read32(DMA5_CURR_DESC_PTR) +#define bfin_write_DMA5_CURR_DESC_PTR(val) bfin_write32(DMA5_CURR_DESC_PTR, val) +#define bfin_read_DMA5_CURR_ADDR() bfin_read32(DMA5_CURR_ADDR) +#define bfin_write_DMA5_CURR_ADDR(val) bfin_write32(DMA5_CURR_ADDR, val) +#define bfin_read_DMA5_CURR_X_COUNT() bfin_read16(DMA5_CURR_X_COUNT) +#define bfin_write_DMA5_CURR_X_COUNT(val) bfin_write16(DMA5_CURR_X_COUNT, val) +#define bfin_read_DMA5_CURR_Y_COUNT() bfin_read16(DMA5_CURR_Y_COUNT) +#define bfin_write_DMA5_CURR_Y_COUNT(val) bfin_write16(DMA5_CURR_Y_COUNT, val) +#define bfin_read_DMA5_IRQ_STATUS() bfin_read16(DMA5_IRQ_STATUS) +#define bfin_write_DMA5_IRQ_STATUS(val) bfin_write16(DMA5_IRQ_STATUS, val) +#define bfin_read_DMA5_PERIPHERAL_MAP() bfin_read16(DMA5_PERIPHERAL_MAP) +#define bfin_write_DMA5_PERIPHERAL_MAP(val) bfin_write16(DMA5_PERIPHERAL_MAP, val) + +#define bfin_read_DMA6_CONFIG() bfin_read16(DMA6_CONFIG) +#define bfin_write_DMA6_CONFIG(val) bfin_write16(DMA6_CONFIG, val) +#define bfin_read_DMA6_NEXT_DESC_PTR() bfin_read32(DMA6_NEXT_DESC_PTR) +#define bfin_write_DMA6_NEXT_DESC_PTR(val) bfin_write32(DMA6_NEXT_DESC_PTR, val) +#define bfin_read_DMA6_START_ADDR() bfin_read32(DMA6_START_ADDR) +#define bfin_write_DMA6_START_ADDR(val) bfin_write32(DMA6_START_ADDR, val) +#define bfin_read_DMA6_X_COUNT() bfin_read16(DMA6_X_COUNT) +#define bfin_write_DMA6_X_COUNT(val) bfin_write16(DMA6_X_COUNT, val) +#define bfin_read_DMA6_Y_COUNT() bfin_read16(DMA6_Y_COUNT) +#define bfin_write_DMA6_Y_COUNT(val) bfin_write16(DMA6_Y_COUNT, val) +#define bfin_read_DMA6_X_MODIFY() bfin_read16(DMA6_X_MODIFY) +#define bfin_write_DMA6_X_MODIFY(val) bfin_write16(DMA6_X_MODIFY, val) +#define bfin_read_DMA6_Y_MODIFY() bfin_read16(DMA6_Y_MODIFY) +#define bfin_write_DMA6_Y_MODIFY(val) bfin_write16(DMA6_Y_MODIFY, val) +#define bfin_read_DMA6_CURR_DESC_PTR() bfin_read32(DMA6_CURR_DESC_PTR) +#define bfin_write_DMA6_CURR_DESC_PTR(val) bfin_write32(DMA6_CURR_DESC_PTR, val) +#define bfin_read_DMA6_CURR_ADDR() bfin_read32(DMA6_CURR_ADDR) +#define bfin_write_DMA6_CURR_ADDR(val) bfin_write32(DMA6_CURR_ADDR, val) +#define bfin_read_DMA6_CURR_X_COUNT() bfin_read16(DMA6_CURR_X_COUNT) +#define bfin_write_DMA6_CURR_X_COUNT(val) bfin_write16(DMA6_CURR_X_COUNT, val) +#define bfin_read_DMA6_CURR_Y_COUNT() bfin_read16(DMA6_CURR_Y_COUNT) +#define bfin_write_DMA6_CURR_Y_COUNT(val) bfin_write16(DMA6_CURR_Y_COUNT, val) +#define bfin_read_DMA6_IRQ_STATUS() bfin_read16(DMA6_IRQ_STATUS) +#define bfin_write_DMA6_IRQ_STATUS(val) bfin_write16(DMA6_IRQ_STATUS, val) +#define bfin_read_DMA6_PERIPHERAL_MAP() bfin_read16(DMA6_PERIPHERAL_MAP) +#define bfin_write_DMA6_PERIPHERAL_MAP(val) bfin_write16(DMA6_PERIPHERAL_MAP, val) + +#define bfin_read_DMA7_CONFIG() bfin_read16(DMA7_CONFIG) +#define bfin_write_DMA7_CONFIG(val) bfin_write16(DMA7_CONFIG, val) +#define bfin_read_DMA7_NEXT_DESC_PTR() bfin_read32(DMA7_NEXT_DESC_PTR) +#define bfin_write_DMA7_NEXT_DESC_PTR(val) bfin_write32(DMA7_NEXT_DESC_PTR, val) +#define bfin_read_DMA7_START_ADDR() bfin_read32(DMA7_START_ADDR) +#define bfin_write_DMA7_START_ADDR(val) bfin_write32(DMA7_START_ADDR, val) +#define bfin_read_DMA7_X_COUNT() bfin_read16(DMA7_X_COUNT) +#define bfin_write_DMA7_X_COUNT(val) bfin_write16(DMA7_X_COUNT, val) +#define bfin_read_DMA7_Y_COUNT() bfin_read16(DMA7_Y_COUNT) +#define bfin_write_DMA7_Y_COUNT(val) bfin_write16(DMA7_Y_COUNT, val) +#define bfin_read_DMA7_X_MODIFY() bfin_read16(DMA7_X_MODIFY) +#define bfin_write_DMA7_X_MODIFY(val) bfin_write16(DMA7_X_MODIFY, val) +#define bfin_read_DMA7_Y_MODIFY() bfin_read16(DMA7_Y_MODIFY) +#define bfin_write_DMA7_Y_MODIFY(val) bfin_write16(DMA7_Y_MODIFY, val) +#define bfin_read_DMA7_CURR_DESC_PTR() bfin_read32(DMA7_CURR_DESC_PTR) +#define bfin_write_DMA7_CURR_DESC_PTR(val) bfin_write32(DMA7_CURR_DESC_PTR, val) +#define bfin_read_DMA7_CURR_ADDR() bfin_read32(DMA7_CURR_ADDR) +#define bfin_write_DMA7_CURR_ADDR(val) bfin_write32(DMA7_CURR_ADDR, val) +#define bfin_read_DMA7_CURR_X_COUNT() bfin_read16(DMA7_CURR_X_COUNT) +#define bfin_write_DMA7_CURR_X_COUNT(val) bfin_write16(DMA7_CURR_X_COUNT, val) +#define bfin_read_DMA7_CURR_Y_COUNT() bfin_read16(DMA7_CURR_Y_COUNT) +#define bfin_write_DMA7_CURR_Y_COUNT(val) bfin_write16(DMA7_CURR_Y_COUNT, val) +#define bfin_read_DMA7_IRQ_STATUS() bfin_read16(DMA7_IRQ_STATUS) +#define bfin_write_DMA7_IRQ_STATUS(val) bfin_write16(DMA7_IRQ_STATUS, val) +#define bfin_read_DMA7_PERIPHERAL_MAP() bfin_read16(DMA7_PERIPHERAL_MAP) +#define bfin_write_DMA7_PERIPHERAL_MAP(val) bfin_write16(DMA7_PERIPHERAL_MAP, val) + +#define bfin_read_DMA8_CONFIG() bfin_read16(DMA8_CONFIG) +#define bfin_write_DMA8_CONFIG(val) bfin_write16(DMA8_CONFIG, val) +#define bfin_read_DMA8_NEXT_DESC_PTR() bfin_read32(DMA8_NEXT_DESC_PTR) +#define bfin_write_DMA8_NEXT_DESC_PTR(val) bfin_write32(DMA8_NEXT_DESC_PTR, val) +#define bfin_read_DMA8_START_ADDR() bfin_read32(DMA8_START_ADDR) +#define bfin_write_DMA8_START_ADDR(val) bfin_write32(DMA8_START_ADDR, val) +#define bfin_read_DMA8_X_COUNT() bfin_read16(DMA8_X_COUNT) +#define bfin_write_DMA8_X_COUNT(val) bfin_write16(DMA8_X_COUNT, val) +#define bfin_read_DMA8_Y_COUNT() bfin_read16(DMA8_Y_COUNT) +#define bfin_write_DMA8_Y_COUNT(val) bfin_write16(DMA8_Y_COUNT, val) +#define bfin_read_DMA8_X_MODIFY() bfin_read16(DMA8_X_MODIFY) +#define bfin_write_DMA8_X_MODIFY(val) bfin_write16(DMA8_X_MODIFY, val) +#define bfin_read_DMA8_Y_MODIFY() bfin_read16(DMA8_Y_MODIFY) +#define bfin_write_DMA8_Y_MODIFY(val) bfin_write16(DMA8_Y_MODIFY, val) +#define bfin_read_DMA8_CURR_DESC_PTR() bfin_read32(DMA8_CURR_DESC_PTR) +#define bfin_write_DMA8_CURR_DESC_PTR(val) bfin_write32(DMA8_CURR_DESC_PTR, val) +#define bfin_read_DMA8_CURR_ADDR() bfin_read32(DMA8_CURR_ADDR) +#define bfin_write_DMA8_CURR_ADDR(val) bfin_write32(DMA8_CURR_ADDR, val) +#define bfin_read_DMA8_CURR_X_COUNT() bfin_read16(DMA8_CURR_X_COUNT) +#define bfin_write_DMA8_CURR_X_COUNT(val) bfin_write16(DMA8_CURR_X_COUNT, val) +#define bfin_read_DMA8_CURR_Y_COUNT() bfin_read16(DMA8_CURR_Y_COUNT) +#define bfin_write_DMA8_CURR_Y_COUNT(val) bfin_write16(DMA8_CURR_Y_COUNT, val) +#define bfin_read_DMA8_IRQ_STATUS() bfin_read16(DMA8_IRQ_STATUS) +#define bfin_write_DMA8_IRQ_STATUS(val) bfin_write16(DMA8_IRQ_STATUS, val) +#define bfin_read_DMA8_PERIPHERAL_MAP() bfin_read16(DMA8_PERIPHERAL_MAP) +#define bfin_write_DMA8_PERIPHERAL_MAP(val) bfin_write16(DMA8_PERIPHERAL_MAP, val) + +#define bfin_read_DMA9_CONFIG() bfin_read16(DMA9_CONFIG) +#define bfin_write_DMA9_CONFIG(val) bfin_write16(DMA9_CONFIG, val) +#define bfin_read_DMA9_NEXT_DESC_PTR() bfin_read32(DMA9_NEXT_DESC_PTR) +#define bfin_write_DMA9_NEXT_DESC_PTR(val) bfin_write32(DMA9_NEXT_DESC_PTR, val) +#define bfin_read_DMA9_START_ADDR() bfin_read32(DMA9_START_ADDR) +#define bfin_write_DMA9_START_ADDR(val) bfin_write32(DMA9_START_ADDR, val) +#define bfin_read_DMA9_X_COUNT() bfin_read16(DMA9_X_COUNT) +#define bfin_write_DMA9_X_COUNT(val) bfin_write16(DMA9_X_COUNT, val) +#define bfin_read_DMA9_Y_COUNT() bfin_read16(DMA9_Y_COUNT) +#define bfin_write_DMA9_Y_COUNT(val) bfin_write16(DMA9_Y_COUNT, val) +#define bfin_read_DMA9_X_MODIFY() bfin_read16(DMA9_X_MODIFY) +#define bfin_write_DMA9_X_MODIFY(val) bfin_write16(DMA9_X_MODIFY, val) +#define bfin_read_DMA9_Y_MODIFY() bfin_read16(DMA9_Y_MODIFY) +#define bfin_write_DMA9_Y_MODIFY(val) bfin_write16(DMA9_Y_MODIFY, val) +#define bfin_read_DMA9_CURR_DESC_PTR() bfin_read32(DMA9_CURR_DESC_PTR) +#define bfin_write_DMA9_CURR_DESC_PTR(val) bfin_write32(DMA9_CURR_DESC_PTR, val) +#define bfin_read_DMA9_CURR_ADDR() bfin_read32(DMA9_CURR_ADDR) +#define bfin_write_DMA9_CURR_ADDR(val) bfin_write32(DMA9_CURR_ADDR, val) +#define bfin_read_DMA9_CURR_X_COUNT() bfin_read16(DMA9_CURR_X_COUNT) +#define bfin_write_DMA9_CURR_X_COUNT(val) bfin_write16(DMA9_CURR_X_COUNT, val) +#define bfin_read_DMA9_CURR_Y_COUNT() bfin_read16(DMA9_CURR_Y_COUNT) +#define bfin_write_DMA9_CURR_Y_COUNT(val) bfin_write16(DMA9_CURR_Y_COUNT, val) +#define bfin_read_DMA9_IRQ_STATUS() bfin_read16(DMA9_IRQ_STATUS) +#define bfin_write_DMA9_IRQ_STATUS(val) bfin_write16(DMA9_IRQ_STATUS, val) +#define bfin_read_DMA9_PERIPHERAL_MAP() bfin_read16(DMA9_PERIPHERAL_MAP) +#define bfin_write_DMA9_PERIPHERAL_MAP(val) bfin_write16(DMA9_PERIPHERAL_MAP, val) + +#define bfin_read_DMA10_CONFIG() bfin_read16(DMA10_CONFIG) +#define bfin_write_DMA10_CONFIG(val) bfin_write16(DMA10_CONFIG, val) +#define bfin_read_DMA10_NEXT_DESC_PTR() bfin_read32(DMA10_NEXT_DESC_PTR) +#define bfin_write_DMA10_NEXT_DESC_PTR(val) bfin_write32(DMA10_NEXT_DESC_PTR, val) +#define bfin_read_DMA10_START_ADDR() bfin_read32(DMA10_START_ADDR) +#define bfin_write_DMA10_START_ADDR(val) bfin_write32(DMA10_START_ADDR, val) +#define bfin_read_DMA10_X_COUNT() bfin_read16(DMA10_X_COUNT) +#define bfin_write_DMA10_X_COUNT(val) bfin_write16(DMA10_X_COUNT, val) +#define bfin_read_DMA10_Y_COUNT() bfin_read16(DMA10_Y_COUNT) +#define bfin_write_DMA10_Y_COUNT(val) bfin_write16(DMA10_Y_COUNT, val) +#define bfin_read_DMA10_X_MODIFY() bfin_read16(DMA10_X_MODIFY) +#define bfin_write_DMA10_X_MODIFY(val) bfin_write16(DMA10_X_MODIFY, val) +#define bfin_read_DMA10_Y_MODIFY() bfin_read16(DMA10_Y_MODIFY) +#define bfin_write_DMA10_Y_MODIFY(val) bfin_write16(DMA10_Y_MODIFY, val) +#define bfin_read_DMA10_CURR_DESC_PTR() bfin_read32(DMA10_CURR_DESC_PTR) +#define bfin_write_DMA10_CURR_DESC_PTR(val) bfin_write32(DMA10_CURR_DESC_PTR, val) +#define bfin_read_DMA10_CURR_ADDR() bfin_read32(DMA10_CURR_ADDR) +#define bfin_write_DMA10_CURR_ADDR(val) bfin_write32(DMA10_CURR_ADDR, val) +#define bfin_read_DMA10_CURR_X_COUNT() bfin_read16(DMA10_CURR_X_COUNT) +#define bfin_write_DMA10_CURR_X_COUNT(val) bfin_write16(DMA10_CURR_X_COUNT, val) +#define bfin_read_DMA10_CURR_Y_COUNT() bfin_read16(DMA10_CURR_Y_COUNT) +#define bfin_write_DMA10_CURR_Y_COUNT(val) bfin_write16(DMA10_CURR_Y_COUNT, val) +#define bfin_read_DMA10_IRQ_STATUS() bfin_read16(DMA10_IRQ_STATUS) +#define bfin_write_DMA10_IRQ_STATUS(val) bfin_write16(DMA10_IRQ_STATUS, val) +#define bfin_read_DMA10_PERIPHERAL_MAP() bfin_read16(DMA10_PERIPHERAL_MAP) +#define bfin_write_DMA10_PERIPHERAL_MAP(val) bfin_write16(DMA10_PERIPHERAL_MAP, val) + +#define bfin_read_DMA11_CONFIG() bfin_read16(DMA11_CONFIG) +#define bfin_write_DMA11_CONFIG(val) bfin_write16(DMA11_CONFIG, val) +#define bfin_read_DMA11_NEXT_DESC_PTR() bfin_read32(DMA11_NEXT_DESC_PTR) +#define bfin_write_DMA11_NEXT_DESC_PTR(val) bfin_write32(DMA11_NEXT_DESC_PTR, val) +#define bfin_read_DMA11_START_ADDR() bfin_read32(DMA11_START_ADDR) +#define bfin_write_DMA11_START_ADDR(val) bfin_write32(DMA11_START_ADDR, val) +#define bfin_read_DMA11_X_COUNT() bfin_read16(DMA11_X_COUNT) +#define bfin_write_DMA11_X_COUNT(val) bfin_write16(DMA11_X_COUNT, val) +#define bfin_read_DMA11_Y_COUNT() bfin_read16(DMA11_Y_COUNT) +#define bfin_write_DMA11_Y_COUNT(val) bfin_write16(DMA11_Y_COUNT, val) +#define bfin_read_DMA11_X_MODIFY() bfin_read16(DMA11_X_MODIFY) +#define bfin_write_DMA11_X_MODIFY(val) bfin_write16(DMA11_X_MODIFY, val) +#define bfin_read_DMA11_Y_MODIFY() bfin_read16(DMA11_Y_MODIFY) +#define bfin_write_DMA11_Y_MODIFY(val) bfin_write16(DMA11_Y_MODIFY, val) +#define bfin_read_DMA11_CURR_DESC_PTR() bfin_read32(DMA11_CURR_DESC_PTR) +#define bfin_write_DMA11_CURR_DESC_PTR(val) bfin_write32(DMA11_CURR_DESC_PTR, val) +#define bfin_read_DMA11_CURR_ADDR() bfin_read32(DMA11_CURR_ADDR) +#define bfin_write_DMA11_CURR_ADDR(val) bfin_write32(DMA11_CURR_ADDR, val) +#define bfin_read_DMA11_CURR_X_COUNT() bfin_read16(DMA11_CURR_X_COUNT) +#define bfin_write_DMA11_CURR_X_COUNT(val) bfin_write16(DMA11_CURR_X_COUNT, val) +#define bfin_read_DMA11_CURR_Y_COUNT() bfin_read16(DMA11_CURR_Y_COUNT) +#define bfin_write_DMA11_CURR_Y_COUNT(val) bfin_write16(DMA11_CURR_Y_COUNT, val) +#define bfin_read_DMA11_IRQ_STATUS() bfin_read16(DMA11_IRQ_STATUS) +#define bfin_write_DMA11_IRQ_STATUS(val) bfin_write16(DMA11_IRQ_STATUS, val) +#define bfin_read_DMA11_PERIPHERAL_MAP() bfin_read16(DMA11_PERIPHERAL_MAP) +#define bfin_write_DMA11_PERIPHERAL_MAP(val) bfin_write16(DMA11_PERIPHERAL_MAP, val) + +#define bfin_read_MDMA_D0_CONFIG() bfin_read16(MDMA_D0_CONFIG) +#define bfin_write_MDMA_D0_CONFIG(val) bfin_write16(MDMA_D0_CONFIG, val) +#define bfin_read_MDMA_D0_NEXT_DESC_PTR() bfin_read32(MDMA_D0_NEXT_DESC_PTR) +#define bfin_write_MDMA_D0_NEXT_DESC_PTR(val) bfin_write32(MDMA_D0_NEXT_DESC_PTR, val) +#define bfin_read_MDMA_D0_START_ADDR() bfin_read32(MDMA_D0_START_ADDR) +#define bfin_write_MDMA_D0_START_ADDR(val) bfin_write32(MDMA_D0_START_ADDR, val) +#define bfin_read_MDMA_D0_X_COUNT() bfin_read16(MDMA_D0_X_COUNT) +#define bfin_write_MDMA_D0_X_COUNT(val) bfin_write16(MDMA_D0_X_COUNT, val) +#define bfin_read_MDMA_D0_Y_COUNT() bfin_read16(MDMA_D0_Y_COUNT) +#define bfin_write_MDMA_D0_Y_COUNT(val) bfin_write16(MDMA_D0_Y_COUNT, val) +#define bfin_read_MDMA_D0_X_MODIFY() bfin_read16(MDMA_D0_X_MODIFY) +#define bfin_write_MDMA_D0_X_MODIFY(val) bfin_write16(MDMA_D0_X_MODIFY, val) +#define bfin_read_MDMA_D0_Y_MODIFY() bfin_read16(MDMA_D0_Y_MODIFY) +#define bfin_write_MDMA_D0_Y_MODIFY(val) bfin_write16(MDMA_D0_Y_MODIFY, val) +#define bfin_read_MDMA_D0_CURR_DESC_PTR() bfin_read32(MDMA_D0_CURR_DESC_PTR) +#define bfin_write_MDMA_D0_CURR_DESC_PTR(val) bfin_write32(MDMA_D0_CURR_DESC_PTR, val) +#define bfin_read_MDMA_D0_CURR_ADDR() bfin_read32(MDMA_D0_CURR_ADDR) +#define bfin_write_MDMA_D0_CURR_ADDR(val) bfin_write32(MDMA_D0_CURR_ADDR, val) +#define bfin_read_MDMA_D0_CURR_X_COUNT() bfin_read16(MDMA_D0_CURR_X_COUNT) +#define bfin_write_MDMA_D0_CURR_X_COUNT(val) bfin_write16(MDMA_D0_CURR_X_COUNT, val) +#define bfin_read_MDMA_D0_CURR_Y_COUNT() bfin_read16(MDMA_D0_CURR_Y_COUNT) +#define bfin_write_MDMA_D0_CURR_Y_COUNT(val) bfin_write16(MDMA_D0_CURR_Y_COUNT, val) +#define bfin_read_MDMA_D0_IRQ_STATUS() bfin_read16(MDMA_D0_IRQ_STATUS) +#define bfin_write_MDMA_D0_IRQ_STATUS(val) bfin_write16(MDMA_D0_IRQ_STATUS, val) +#define bfin_read_MDMA_D0_PERIPHERAL_MAP() bfin_read16(MDMA_D0_PERIPHERAL_MAP) +#define bfin_write_MDMA_D0_PERIPHERAL_MAP(val) bfin_write16(MDMA_D0_PERIPHERAL_MAP, val) + +#define bfin_read_MDMA_S0_CONFIG() bfin_read16(MDMA_S0_CONFIG) +#define bfin_write_MDMA_S0_CONFIG(val) bfin_write16(MDMA_S0_CONFIG, val) +#define bfin_read_MDMA_S0_NEXT_DESC_PTR() bfin_read32(MDMA_S0_NEXT_DESC_PTR) +#define bfin_write_MDMA_S0_NEXT_DESC_PTR(val) bfin_write32(MDMA_S0_NEXT_DESC_PTR, val) +#define bfin_read_MDMA_S0_START_ADDR() bfin_read32(MDMA_S0_START_ADDR) +#define bfin_write_MDMA_S0_START_ADDR(val) bfin_write32(MDMA_S0_START_ADDR, val) +#define bfin_read_MDMA_S0_X_COUNT() bfin_read16(MDMA_S0_X_COUNT) +#define bfin_write_MDMA_S0_X_COUNT(val) bfin_write16(MDMA_S0_X_COUNT, val) +#define bfin_read_MDMA_S0_Y_COUNT() bfin_read16(MDMA_S0_Y_COUNT) +#define bfin_write_MDMA_S0_Y_COUNT(val) bfin_write16(MDMA_S0_Y_COUNT, val) +#define bfin_read_MDMA_S0_X_MODIFY() bfin_read16(MDMA_S0_X_MODIFY) +#define bfin_write_MDMA_S0_X_MODIFY(val) bfin_write16(MDMA_S0_X_MODIFY, val) +#define bfin_read_MDMA_S0_Y_MODIFY() bfin_read16(MDMA_S0_Y_MODIFY) +#define bfin_write_MDMA_S0_Y_MODIFY(val) bfin_write16(MDMA_S0_Y_MODIFY, val) +#define bfin_read_MDMA_S0_CURR_DESC_PTR() bfin_read32(MDMA_S0_CURR_DESC_PTR) +#define bfin_write_MDMA_S0_CURR_DESC_PTR(val) bfin_write32(MDMA_S0_CURR_DESC_PTR, val) +#define bfin_read_MDMA_S0_CURR_ADDR() bfin_read32(MDMA_S0_CURR_ADDR) +#define bfin_write_MDMA_S0_CURR_ADDR(val) bfin_write32(MDMA_S0_CURR_ADDR, val) +#define bfin_read_MDMA_S0_CURR_X_COUNT() bfin_read16(MDMA_S0_CURR_X_COUNT) +#define bfin_write_MDMA_S0_CURR_X_COUNT(val) bfin_write16(MDMA_S0_CURR_X_COUNT, val) +#define bfin_read_MDMA_S0_CURR_Y_COUNT() bfin_read16(MDMA_S0_CURR_Y_COUNT) +#define bfin_write_MDMA_S0_CURR_Y_COUNT(val) bfin_write16(MDMA_S0_CURR_Y_COUNT, val) +#define bfin_read_MDMA_S0_IRQ_STATUS() bfin_read16(MDMA_S0_IRQ_STATUS) +#define bfin_write_MDMA_S0_IRQ_STATUS(val) bfin_write16(MDMA_S0_IRQ_STATUS, val) +#define bfin_read_MDMA_S0_PERIPHERAL_MAP() bfin_read16(MDMA_S0_PERIPHERAL_MAP) +#define bfin_write_MDMA_S0_PERIPHERAL_MAP(val) bfin_write16(MDMA_S0_PERIPHERAL_MAP, val) + +#define bfin_read_MDMA_D1_CONFIG() bfin_read16(MDMA_D1_CONFIG) +#define bfin_write_MDMA_D1_CONFIG(val) bfin_write16(MDMA_D1_CONFIG, val) +#define bfin_read_MDMA_D1_NEXT_DESC_PTR() bfin_read32(MDMA_D1_NEXT_DESC_PTR) +#define bfin_write_MDMA_D1_NEXT_DESC_PTR(val) bfin_write32(MDMA_D1_NEXT_DESC_PTR, val) +#define bfin_read_MDMA_D1_START_ADDR() bfin_read32(MDMA_D1_START_ADDR) +#define bfin_write_MDMA_D1_START_ADDR(val) bfin_write32(MDMA_D1_START_ADDR, val) +#define bfin_read_MDMA_D1_X_COUNT() bfin_read16(MDMA_D1_X_COUNT) +#define bfin_write_MDMA_D1_X_COUNT(val) bfin_write16(MDMA_D1_X_COUNT, val) +#define bfin_read_MDMA_D1_Y_COUNT() bfin_read16(MDMA_D1_Y_COUNT) +#define bfin_write_MDMA_D1_Y_COUNT(val) bfin_write16(MDMA_D1_Y_COUNT, val) +#define bfin_read_MDMA_D1_X_MODIFY() bfin_read16(MDMA_D1_X_MODIFY) +#define bfin_write_MDMA_D1_X_MODIFY(val) bfin_write16(MDMA_D1_X_MODIFY, val) +#define bfin_read_MDMA_D1_Y_MODIFY() bfin_read16(MDMA_D1_Y_MODIFY) +#define bfin_write_MDMA_D1_Y_MODIFY(val) bfin_write16(MDMA_D1_Y_MODIFY, val) +#define bfin_read_MDMA_D1_CURR_DESC_PTR() bfin_read32(MDMA_D1_CURR_DESC_PTR) +#define bfin_write_MDMA_D1_CURR_DESC_PTR(val) bfin_write32(MDMA_D1_CURR_DESC_PTR, val) +#define bfin_read_MDMA_D1_CURR_ADDR() bfin_read32(MDMA_D1_CURR_ADDR) +#define bfin_write_MDMA_D1_CURR_ADDR(val) bfin_write32(MDMA_D1_CURR_ADDR, val) +#define bfin_read_MDMA_D1_CURR_X_COUNT() bfin_read16(MDMA_D1_CURR_X_COUNT) +#define bfin_write_MDMA_D1_CURR_X_COUNT(val) bfin_write16(MDMA_D1_CURR_X_COUNT, val) +#define bfin_read_MDMA_D1_CURR_Y_COUNT() bfin_read16(MDMA_D1_CURR_Y_COUNT) +#define bfin_write_MDMA_D1_CURR_Y_COUNT(val) bfin_write16(MDMA_D1_CURR_Y_COUNT, val) +#define bfin_read_MDMA_D1_IRQ_STATUS() bfin_read16(MDMA_D1_IRQ_STATUS) +#define bfin_write_MDMA_D1_IRQ_STATUS(val) bfin_write16(MDMA_D1_IRQ_STATUS, val) +#define bfin_read_MDMA_D1_PERIPHERAL_MAP() bfin_read16(MDMA_D1_PERIPHERAL_MAP) +#define bfin_write_MDMA_D1_PERIPHERAL_MAP(val) bfin_write16(MDMA_D1_PERIPHERAL_MAP, val) + +#define bfin_read_MDMA_S1_CONFIG() bfin_read16(MDMA_S1_CONFIG) +#define bfin_write_MDMA_S1_CONFIG(val) bfin_write16(MDMA_S1_CONFIG, val) +#define bfin_read_MDMA_S1_NEXT_DESC_PTR() bfin_read32(MDMA_S1_NEXT_DESC_PTR) +#define bfin_write_MDMA_S1_NEXT_DESC_PTR(val) bfin_write32(MDMA_S1_NEXT_DESC_PTR, val) +#define bfin_read_MDMA_S1_START_ADDR() bfin_read32(MDMA_S1_START_ADDR) +#define bfin_write_MDMA_S1_START_ADDR(val) bfin_write32(MDMA_S1_START_ADDR, val) +#define bfin_read_MDMA_S1_X_COUNT() bfin_read16(MDMA_S1_X_COUNT) +#define bfin_write_MDMA_S1_X_COUNT(val) bfin_write16(MDMA_S1_X_COUNT, val) +#define bfin_read_MDMA_S1_Y_COUNT() bfin_read16(MDMA_S1_Y_COUNT) +#define bfin_write_MDMA_S1_Y_COUNT(val) bfin_write16(MDMA_S1_Y_COUNT, val) +#define bfin_read_MDMA_S1_X_MODIFY() bfin_read16(MDMA_S1_X_MODIFY) +#define bfin_write_MDMA_S1_X_MODIFY(val) bfin_write16(MDMA_S1_X_MODIFY, val) +#define bfin_read_MDMA_S1_Y_MODIFY() bfin_read16(MDMA_S1_Y_MODIFY) +#define bfin_write_MDMA_S1_Y_MODIFY(val) bfin_write16(MDMA_S1_Y_MODIFY, val) +#define bfin_read_MDMA_S1_CURR_DESC_PTR() bfin_read32(MDMA_S1_CURR_DESC_PTR) +#define bfin_write_MDMA_S1_CURR_DESC_PTR(val) bfin_write32(MDMA_S1_CURR_DESC_PTR, val) +#define bfin_read_MDMA_S1_CURR_ADDR() bfin_read32(MDMA_S1_CURR_ADDR) +#define bfin_write_MDMA_S1_CURR_ADDR(val) bfin_write32(MDMA_S1_CURR_ADDR, val) +#define bfin_read_MDMA_S1_CURR_X_COUNT() bfin_read16(MDMA_S1_CURR_X_COUNT) +#define bfin_write_MDMA_S1_CURR_X_COUNT(val) bfin_write16(MDMA_S1_CURR_X_COUNT, val) +#define bfin_read_MDMA_S1_CURR_Y_COUNT() bfin_read16(MDMA_S1_CURR_Y_COUNT) +#define bfin_write_MDMA_S1_CURR_Y_COUNT(val) bfin_write16(MDMA_S1_CURR_Y_COUNT, val) +#define bfin_read_MDMA_S1_IRQ_STATUS() bfin_read16(MDMA_S1_IRQ_STATUS) +#define bfin_write_MDMA_S1_IRQ_STATUS(val) bfin_write16(MDMA_S1_IRQ_STATUS, val) +#define bfin_read_MDMA_S1_PERIPHERAL_MAP() bfin_read16(MDMA_S1_PERIPHERAL_MAP) +#define bfin_write_MDMA_S1_PERIPHERAL_MAP(val) bfin_write16(MDMA_S1_PERIPHERAL_MAP, val) + + +/* Parallel Peripheral Interface (0xFFC01000 - 0xFFC010FF) */ +#define bfin_read_PPI_CONTROL() bfin_read16(PPI_CONTROL) +#define bfin_write_PPI_CONTROL(val) bfin_write16(PPI_CONTROL, val) +#define bfin_read_PPI_STATUS() bfin_read16(PPI_STATUS) +#define bfin_write_PPI_STATUS(val) bfin_write16(PPI_STATUS, val) +#define bfin_read_PPI_DELAY() bfin_read16(PPI_DELAY) +#define bfin_write_PPI_DELAY(val) bfin_write16(PPI_DELAY, val) +#define bfin_read_PPI_COUNT() bfin_read16(PPI_COUNT) +#define bfin_write_PPI_COUNT(val) bfin_write16(PPI_COUNT, val) +#define bfin_read_PPI_FRAME() bfin_read16(PPI_FRAME) +#define bfin_write_PPI_FRAME(val) bfin_write16(PPI_FRAME, val) + + +/* Two-Wire Interface (0xFFC01400 - 0xFFC014FF) */ + +/* General Purpose I/O Port G (0xFFC01500 - 0xFFC015FF) */ +#define bfin_read_PORTGIO() bfin_read16(PORTGIO) +#define bfin_write_PORTGIO(val) bfin_write16(PORTGIO, val) +#define bfin_read_PORTGIO_CLEAR() bfin_read16(PORTGIO_CLEAR) +#define bfin_write_PORTGIO_CLEAR(val) bfin_write16(PORTGIO_CLEAR, val) +#define bfin_read_PORTGIO_SET() bfin_read16(PORTGIO_SET) +#define bfin_write_PORTGIO_SET(val) bfin_write16(PORTGIO_SET, val) +#define bfin_read_PORTGIO_TOGGLE() bfin_read16(PORTGIO_TOGGLE) +#define bfin_write_PORTGIO_TOGGLE(val) bfin_write16(PORTGIO_TOGGLE, val) +#define bfin_read_PORTGIO_MASKA() bfin_read16(PORTGIO_MASKA) +#define bfin_write_PORTGIO_MASKA(val) bfin_write16(PORTGIO_MASKA, val) +#define bfin_read_PORTGIO_MASKA_CLEAR() bfin_read16(PORTGIO_MASKA_CLEAR) +#define bfin_write_PORTGIO_MASKA_CLEAR(val) bfin_write16(PORTGIO_MASKA_CLEAR, val) +#define bfin_read_PORTGIO_MASKA_SET() bfin_read16(PORTGIO_MASKA_SET) +#define bfin_write_PORTGIO_MASKA_SET(val) bfin_write16(PORTGIO_MASKA_SET, val) +#define bfin_read_PORTGIO_MASKA_TOGGLE() bfin_read16(PORTGIO_MASKA_TOGGLE) +#define bfin_write_PORTGIO_MASKA_TOGGLE(val) bfin_write16(PORTGIO_MASKA_TOGGLE, val) +#define bfin_read_PORTGIO_MASKB() bfin_read16(PORTGIO_MASKB) +#define bfin_write_PORTGIO_MASKB(val) bfin_write16(PORTGIO_MASKB, val) +#define bfin_read_PORTGIO_MASKB_CLEAR() bfin_read16(PORTGIO_MASKB_CLEAR) +#define bfin_write_PORTGIO_MASKB_CLEAR(val) bfin_write16(PORTGIO_MASKB_CLEAR, val) +#define bfin_read_PORTGIO_MASKB_SET() bfin_read16(PORTGIO_MASKB_SET) +#define bfin_write_PORTGIO_MASKB_SET(val) bfin_write16(PORTGIO_MASKB_SET, val) +#define bfin_read_PORTGIO_MASKB_TOGGLE() bfin_read16(PORTGIO_MASKB_TOGGLE) +#define bfin_write_PORTGIO_MASKB_TOGGLE(val) bfin_write16(PORTGIO_MASKB_TOGGLE, val) +#define bfin_read_PORTGIO_DIR() bfin_read16(PORTGIO_DIR) +#define bfin_write_PORTGIO_DIR(val) bfin_write16(PORTGIO_DIR, val) +#define bfin_read_PORTGIO_POLAR() bfin_read16(PORTGIO_POLAR) +#define bfin_write_PORTGIO_POLAR(val) bfin_write16(PORTGIO_POLAR, val) +#define bfin_read_PORTGIO_EDGE() bfin_read16(PORTGIO_EDGE) +#define bfin_write_PORTGIO_EDGE(val) bfin_write16(PORTGIO_EDGE, val) +#define bfin_read_PORTGIO_BOTH() bfin_read16(PORTGIO_BOTH) +#define bfin_write_PORTGIO_BOTH(val) bfin_write16(PORTGIO_BOTH, val) +#define bfin_read_PORTGIO_INEN() bfin_read16(PORTGIO_INEN) +#define bfin_write_PORTGIO_INEN(val) bfin_write16(PORTGIO_INEN, val) + + +/* General Purpose I/O Port H (0xFFC01700 - 0xFFC017FF) */ +#define bfin_read_PORTHIO() bfin_read16(PORTHIO) +#define bfin_write_PORTHIO(val) bfin_write16(PORTHIO, val) +#define bfin_read_PORTHIO_CLEAR() bfin_read16(PORTHIO_CLEAR) +#define bfin_write_PORTHIO_CLEAR(val) bfin_write16(PORTHIO_CLEAR, val) +#define bfin_read_PORTHIO_SET() bfin_read16(PORTHIO_SET) +#define bfin_write_PORTHIO_SET(val) bfin_write16(PORTHIO_SET, val) +#define bfin_read_PORTHIO_TOGGLE() bfin_read16(PORTHIO_TOGGLE) +#define bfin_write_PORTHIO_TOGGLE(val) bfin_write16(PORTHIO_TOGGLE, val) +#define bfin_read_PORTHIO_MASKA() bfin_read16(PORTHIO_MASKA) +#define bfin_write_PORTHIO_MASKA(val) bfin_write16(PORTHIO_MASKA, val) +#define bfin_read_PORTHIO_MASKA_CLEAR() bfin_read16(PORTHIO_MASKA_CLEAR) +#define bfin_write_PORTHIO_MASKA_CLEAR(val) bfin_write16(PORTHIO_MASKA_CLEAR, val) +#define bfin_read_PORTHIO_MASKA_SET() bfin_read16(PORTHIO_MASKA_SET) +#define bfin_write_PORTHIO_MASKA_SET(val) bfin_write16(PORTHIO_MASKA_SET, val) +#define bfin_read_PORTHIO_MASKA_TOGGLE() bfin_read16(PORTHIO_MASKA_TOGGLE) +#define bfin_write_PORTHIO_MASKA_TOGGLE(val) bfin_write16(PORTHIO_MASKA_TOGGLE, val) +#define bfin_read_PORTHIO_MASKB() bfin_read16(PORTHIO_MASKB) +#define bfin_write_PORTHIO_MASKB(val) bfin_write16(PORTHIO_MASKB, val) +#define bfin_read_PORTHIO_MASKB_CLEAR() bfin_read16(PORTHIO_MASKB_CLEAR) +#define bfin_write_PORTHIO_MASKB_CLEAR(val) bfin_write16(PORTHIO_MASKB_CLEAR, val) +#define bfin_read_PORTHIO_MASKB_SET() bfin_read16(PORTHIO_MASKB_SET) +#define bfin_write_PORTHIO_MASKB_SET(val) bfin_write16(PORTHIO_MASKB_SET, val) +#define bfin_read_PORTHIO_MASKB_TOGGLE() bfin_read16(PORTHIO_MASKB_TOGGLE) +#define bfin_write_PORTHIO_MASKB_TOGGLE(val) bfin_write16(PORTHIO_MASKB_TOGGLE, val) +#define bfin_read_PORTHIO_DIR() bfin_read16(PORTHIO_DIR) +#define bfin_write_PORTHIO_DIR(val) bfin_write16(PORTHIO_DIR, val) +#define bfin_read_PORTHIO_POLAR() bfin_read16(PORTHIO_POLAR) +#define bfin_write_PORTHIO_POLAR(val) bfin_write16(PORTHIO_POLAR, val) +#define bfin_read_PORTHIO_EDGE() bfin_read16(PORTHIO_EDGE) +#define bfin_write_PORTHIO_EDGE(val) bfin_write16(PORTHIO_EDGE, val) +#define bfin_read_PORTHIO_BOTH() bfin_read16(PORTHIO_BOTH) +#define bfin_write_PORTHIO_BOTH(val) bfin_write16(PORTHIO_BOTH, val) +#define bfin_read_PORTHIO_INEN() bfin_read16(PORTHIO_INEN) +#define bfin_write_PORTHIO_INEN(val) bfin_write16(PORTHIO_INEN, val) + + +/* UART1 Controller (0xFFC02000 - 0xFFC020FF) */ +#define bfin_read_UART1_THR() bfin_read16(UART1_THR) +#define bfin_write_UART1_THR(val) bfin_write16(UART1_THR, val) +#define bfin_read_UART1_RBR() bfin_read16(UART1_RBR) +#define bfin_write_UART1_RBR(val) bfin_write16(UART1_RBR, val) +#define bfin_read_UART1_DLL() bfin_read16(UART1_DLL) +#define bfin_write_UART1_DLL(val) bfin_write16(UART1_DLL, val) +#define bfin_read_UART1_IER() bfin_read16(UART1_IER) +#define bfin_write_UART1_IER(val) bfin_write16(UART1_IER, val) +#define bfin_read_UART1_DLH() bfin_read16(UART1_DLH) +#define bfin_write_UART1_DLH(val) bfin_write16(UART1_DLH, val) +#define bfin_read_UART1_IIR() bfin_read16(UART1_IIR) +#define bfin_write_UART1_IIR(val) bfin_write16(UART1_IIR, val) +#define bfin_read_UART1_LCR() bfin_read16(UART1_LCR) +#define bfin_write_UART1_LCR(val) bfin_write16(UART1_LCR, val) +#define bfin_read_UART1_MCR() bfin_read16(UART1_MCR) +#define bfin_write_UART1_MCR(val) bfin_write16(UART1_MCR, val) +#define bfin_read_UART1_LSR() bfin_read16(UART1_LSR) +#define bfin_write_UART1_LSR(val) bfin_write16(UART1_LSR, val) +#define bfin_read_UART1_MSR() bfin_read16(UART1_MSR) +#define bfin_write_UART1_MSR(val) bfin_write16(UART1_MSR, val) +#define bfin_read_UART1_SCR() bfin_read16(UART1_SCR) +#define bfin_write_UART1_SCR(val) bfin_write16(UART1_SCR, val) +#define bfin_read_UART1_GCTL() bfin_read16(UART1_GCTL) +#define bfin_write_UART1_GCTL(val) bfin_write16(UART1_GCTL, val) + +/* Omit CAN register sets from the cdefBF534.h (CAN is not in the ADSP-BF51x processor) */ + +/* Pin Control Registers (0xFFC03200 - 0xFFC032FF) */ +#define bfin_read_PORTF_FER() bfin_read16(PORTF_FER) +#define bfin_write_PORTF_FER(val) bfin_write16(PORTF_FER, val) +#define bfin_read_PORTG_FER() bfin_read16(PORTG_FER) +#define bfin_write_PORTG_FER(val) bfin_write16(PORTG_FER, val) +#define bfin_read_PORTH_FER() bfin_read16(PORTH_FER) +#define bfin_write_PORTH_FER(val) bfin_write16(PORTH_FER, val) +#define bfin_read_PORT_MUX() bfin_read16(PORT_MUX) +#define bfin_write_PORT_MUX(val) bfin_write16(PORT_MUX, val) + + +/* Handshake MDMA Registers (0xFFC03300 - 0xFFC033FF) */ +#define bfin_read_HMDMA0_CONTROL() bfin_read16(HMDMA0_CONTROL) +#define bfin_write_HMDMA0_CONTROL(val) bfin_write16(HMDMA0_CONTROL, val) +#define bfin_read_HMDMA0_ECINIT() bfin_read16(HMDMA0_ECINIT) +#define bfin_write_HMDMA0_ECINIT(val) bfin_write16(HMDMA0_ECINIT, val) +#define bfin_read_HMDMA0_BCINIT() bfin_read16(HMDMA0_BCINIT) +#define bfin_write_HMDMA0_BCINIT(val) bfin_write16(HMDMA0_BCINIT, val) +#define bfin_read_HMDMA0_ECURGENT() bfin_read16(HMDMA0_ECURGENT) +#define bfin_write_HMDMA0_ECURGENT(val) bfin_write16(HMDMA0_ECURGENT, val) +#define bfin_read_HMDMA0_ECOVERFLOW() bfin_read16(HMDMA0_ECOVERFLOW) +#define bfin_write_HMDMA0_ECOVERFLOW(val) bfin_write16(HMDMA0_ECOVERFLOW, val) +#define bfin_read_HMDMA0_ECOUNT() bfin_read16(HMDMA0_ECOUNT) +#define bfin_write_HMDMA0_ECOUNT(val) bfin_write16(HMDMA0_ECOUNT, val) +#define bfin_read_HMDMA0_BCOUNT() bfin_read16(HMDMA0_BCOUNT) +#define bfin_write_HMDMA0_BCOUNT(val) bfin_write16(HMDMA0_BCOUNT, val) + +#define bfin_read_HMDMA1_CONTROL() bfin_read16(HMDMA1_CONTROL) +#define bfin_write_HMDMA1_CONTROL(val) bfin_write16(HMDMA1_CONTROL, val) +#define bfin_read_HMDMA1_ECINIT() bfin_read16(HMDMA1_ECINIT) +#define bfin_write_HMDMA1_ECINIT(val) bfin_write16(HMDMA1_ECINIT, val) +#define bfin_read_HMDMA1_BCINIT() bfin_read16(HMDMA1_BCINIT) +#define bfin_write_HMDMA1_BCINIT(val) bfin_write16(HMDMA1_BCINIT, val) +#define bfin_read_HMDMA1_ECURGENT() bfin_read16(HMDMA1_ECURGENT) +#define bfin_write_HMDMA1_ECURGENT(val) bfin_write16(HMDMA1_ECURGENT, val) +#define bfin_read_HMDMA1_ECOVERFLOW() bfin_read16(HMDMA1_ECOVERFLOW) +#define bfin_write_HMDMA1_ECOVERFLOW(val) bfin_write16(HMDMA1_ECOVERFLOW, val) +#define bfin_read_HMDMA1_ECOUNT() bfin_read16(HMDMA1_ECOUNT) +#define bfin_write_HMDMA1_ECOUNT(val) bfin_write16(HMDMA1_ECOUNT, val) +#define bfin_read_HMDMA1_BCOUNT() bfin_read16(HMDMA1_BCOUNT) +#define bfin_write_HMDMA1_BCOUNT(val) bfin_write16(HMDMA1_BCOUNT, val) + +/* ==== end from cdefBF534.h ==== */ + +/* GPIO PIN mux (0xFFC03210 - OxFFC03288) */ + +#define bfin_read_PORTF_MUX() bfin_read16(PORTF_MUX) +#define bfin_write_PORTF_MUX(val) bfin_write16(PORTF_MUX, val) +#define bfin_read_PORTG_MUX() bfin_read16(PORTG_MUX) +#define bfin_write_PORTG_MUX(val) bfin_write16(PORTG_MUX, val) +#define bfin_read_PORTH_MUX() bfin_read16(PORTH_MUX) +#define bfin_write_PORTH_MUX(val) bfin_write16(PORTH_MUX, val) + +#define bfin_read_PORTF_DRIVE() bfin_read16(PORTF_DRIVE) +#define bfin_write_PORTF_DRIVE(val) bfin_write16(PORTF_DRIVE, val) +#define bfin_read_PORTG_DRIVE() bfin_read16(PORTG_DRIVE) +#define bfin_write_PORTG_DRIVE(val) bfin_write16(PORTG_DRIVE, val) +#define bfin_read_PORTH_DRIVE() bfin_read16(PORTH_DRIVE) +#define bfin_write_PORTH_DRIVE(val) bfin_write16(PORTH_DRIVE, val) +#define bfin_read_PORTF_SLEW() bfin_read16(PORTF_SLEW) +#define bfin_write_PORTF_SLEW(val) bfin_write16(PORTF_SLEW, val) +#define bfin_read_PORTG_SLEW() bfin_read16(PORTG_SLEW) +#define bfin_write_PORTG_SLEW(val) bfin_write16(PORTG_SLEW, val) +#define bfin_read_PORTH_SLEW() bfin_read16(PORTH_SLEW) +#define bfin_write_PORTH_SLEW(val) bfin_write16(PORTH_SLEW, val) +#define bfin_read_PORTF_HYSTERISIS() bfin_read16(PORTF_HYSTERISIS) +#define bfin_write_PORTF_HYSTERISIS(val) bfin_write16(PORTF_HYSTERISIS, val) +#define bfin_read_PORTG_HYSTERISIS() bfin_read16(PORTG_HYSTERISIS) +#define bfin_write_PORTG_HYSTERISIS(val) bfin_write16(PORTG_HYSTERISIS, val) +#define bfin_read_PORTH_HYSTERISIS() bfin_read16(PORTH_HYSTERISIS) +#define bfin_write_PORTH_HYSTERISIS(val) bfin_write16(PORTH_HYSTERISIS, val) +#define bfin_read_MISCPORT_DRIVE() bfin_read16(MISCPORT_DRIVE) +#define bfin_write_MISCPORT_DRIVE(val) bfin_write16(MISCPORT_DRIVE, val) +#define bfin_read_MISCPORT_SLEW() bfin_read16(MISCPORT_SLEW) +#define bfin_write_MISCPORT_SLEW(val) bfin_write16(MISCPORT_SLEW, val) +#define bfin_read_MISCPORT_HYSTERISIS() bfin_read16(MISCPORT_HYSTERISIS) +#define bfin_write_MISCPORT_HYSTERISIS(val) bfin_write16(MISCPORT_HYSTERISIS, val) + +/* HOST Port Registers */ + +#define bfin_read_HOST_CONTROL() bfin_read16(HOST_CONTROL) +#define bfin_write_HOST_CONTROL(val) bfin_write16(HOST_CONTROL, val) +#define bfin_read_HOST_STATUS() bfin_read16(HOST_STATUS) +#define bfin_write_HOST_STATUS(val) bfin_write16(HOST_STATUS, val) +#define bfin_read_HOST_TIMEOUT() bfin_read16(HOST_TIMEOUT) +#define bfin_write_HOST_TIMEOUT(val) bfin_write16(HOST_TIMEOUT, val) + +/* Counter Registers */ + +#define bfin_read_CNT_CONFIG() bfin_read16(CNT_CONFIG) +#define bfin_write_CNT_CONFIG(val) bfin_write16(CNT_CONFIG, val) +#define bfin_read_CNT_IMASK() bfin_read16(CNT_IMASK) +#define bfin_write_CNT_IMASK(val) bfin_write16(CNT_IMASK, val) +#define bfin_read_CNT_STATUS() bfin_read16(CNT_STATUS) +#define bfin_write_CNT_STATUS(val) bfin_write16(CNT_STATUS, val) +#define bfin_read_CNT_COMMAND() bfin_read16(CNT_COMMAND) +#define bfin_write_CNT_COMMAND(val) bfin_write16(CNT_COMMAND, val) +#define bfin_read_CNT_DEBOUNCE() bfin_read16(CNT_DEBOUNCE) +#define bfin_write_CNT_DEBOUNCE(val) bfin_write16(CNT_DEBOUNCE, val) +#define bfin_read_CNT_COUNTER() bfin_read32(CNT_COUNTER) +#define bfin_write_CNT_COUNTER(val) bfin_write32(CNT_COUNTER, val) +#define bfin_read_CNT_MAX() bfin_read32(CNT_MAX) +#define bfin_write_CNT_MAX(val) bfin_write32(CNT_MAX, val) +#define bfin_read_CNT_MIN() bfin_read32(CNT_MIN) +#define bfin_write_CNT_MIN(val) bfin_write32(CNT_MIN, val) + +/* OTP/FUSE Registers */ + +#define bfin_read_OTP_CONTROL() bfin_read16(OTP_CONTROL) +#define bfin_write_OTP_CONTROL(val) bfin_write16(OTP_CONTROL, val) +#define bfin_read_OTP_BEN() bfin_read16(OTP_BEN) +#define bfin_write_OTP_BEN(val) bfin_write16(OTP_BEN, val) +#define bfin_read_OTP_STATUS() bfin_read16(OTP_STATUS) +#define bfin_write_OTP_STATUS(val) bfin_write16(OTP_STATUS, val) +#define bfin_read_OTP_TIMING() bfin_read32(OTP_TIMING) +#define bfin_write_OTP_TIMING(val) bfin_write32(OTP_TIMING, val) + +/* Security Registers */ + +#define bfin_read_SECURE_SYSSWT() bfin_read32(SECURE_SYSSWT) +#define bfin_write_SECURE_SYSSWT(val) bfin_write32(SECURE_SYSSWT, val) +#define bfin_read_SECURE_CONTROL() bfin_read16(SECURE_CONTROL) +#define bfin_write_SECURE_CONTROL(val) bfin_write16(SECURE_CONTROL, val) +#define bfin_read_SECURE_STATUS() bfin_read16(SECURE_STATUS) +#define bfin_write_SECURE_STATUS(val) bfin_write16(SECURE_STATUS, val) + +/* OTP Read/Write Data Buffer Registers */ + +#define bfin_read_OTP_DATA0() bfin_read32(OTP_DATA0) +#define bfin_write_OTP_DATA0(val) bfin_write32(OTP_DATA0, val) +#define bfin_read_OTP_DATA1() bfin_read32(OTP_DATA1) +#define bfin_write_OTP_DATA1(val) bfin_write32(OTP_DATA1, val) +#define bfin_read_OTP_DATA2() bfin_read32(OTP_DATA2) +#define bfin_write_OTP_DATA2(val) bfin_write32(OTP_DATA2, val) +#define bfin_read_OTP_DATA3() bfin_read32(OTP_DATA3) +#define bfin_write_OTP_DATA3(val) bfin_write32(OTP_DATA3, val) + +/* NFC Registers */ + +#define bfin_read_NFC_CTL() bfin_read16(NFC_CTL) +#define bfin_write_NFC_CTL(val) bfin_write16(NFC_CTL, val) +#define bfin_read_NFC_STAT() bfin_read16(NFC_STAT) +#define bfin_write_NFC_STAT(val) bfin_write16(NFC_STAT, val) +#define bfin_read_NFC_IRQSTAT() bfin_read16(NFC_IRQSTAT) +#define bfin_write_NFC_IRQSTAT(val) bfin_write16(NFC_IRQSTAT, val) +#define bfin_read_NFC_IRQMASK() bfin_read16(NFC_IRQMASK) +#define bfin_write_NFC_IRQMASK(val) bfin_write16(NFC_IRQMASK, val) +#define bfin_read_NFC_ECC0() bfin_read16(NFC_ECC0) +#define bfin_write_NFC_ECC0(val) bfin_write16(NFC_ECC0, val) +#define bfin_read_NFC_ECC1() bfin_read16(NFC_ECC1) +#define bfin_write_NFC_ECC1(val) bfin_write16(NFC_ECC1, val) +#define bfin_read_NFC_ECC2() bfin_read16(NFC_ECC2) +#define bfin_write_NFC_ECC2(val) bfin_write16(NFC_ECC2, val) +#define bfin_read_NFC_ECC3() bfin_read16(NFC_ECC3) +#define bfin_write_NFC_ECC3(val) bfin_write16(NFC_ECC3, val) +#define bfin_read_NFC_COUNT() bfin_read16(NFC_COUNT) +#define bfin_write_NFC_COUNT(val) bfin_write16(NFC_COUNT, val) +#define bfin_read_NFC_RST() bfin_read16(NFC_RST) +#define bfin_write_NFC_RST(val) bfin_write16(NFC_RST, val) +#define bfin_read_NFC_PGCTL() bfin_read16(NFC_PGCTL) +#define bfin_write_NFC_PGCTL(val) bfin_write16(NFC_PGCTL, val) +#define bfin_read_NFC_READ() bfin_read16(NFC_READ) +#define bfin_write_NFC_READ(val) bfin_write16(NFC_READ, val) +#define bfin_read_NFC_ADDR() bfin_read16(NFC_ADDR) +#define bfin_write_NFC_ADDR(val) bfin_write16(NFC_ADDR, val) +#define bfin_read_NFC_CMD() bfin_read16(NFC_CMD) +#define bfin_write_NFC_CMD(val) bfin_write16(NFC_CMD, val) +#define bfin_read_NFC_DATA_WR() bfin_read16(NFC_DATA_WR) +#define bfin_write_NFC_DATA_WR(val) bfin_write16(NFC_DATA_WR, val) +#define bfin_read_NFC_DATA_RD() bfin_read16(NFC_DATA_RD) +#define bfin_write_NFC_DATA_RD(val) bfin_write16(NFC_DATA_RD, val) + +#endif /* _CDEF_BF52X_H */ diff --git a/arch/blackfin/mach-bf518/include/mach/defBF512.h b/arch/blackfin/mach-bf518/include/mach/defBF512.h new file mode 100644 index 00000000000..a96ca90154d --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/defBF512.h @@ -0,0 +1,42 @@ +/* + * File: include/asm-blackfin/mach-bf518/defBF512.h + * Based on: + * Author: + * + * Created: + * Description: + * + * Rev: + * + * Modified: + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _DEF_BF512_H +#define _DEF_BF512_H + +/* Include all Core registers and bit definitions */ +#include <asm/def_LPBlackfin.h> + +/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF512 */ + +/* Include defBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */ +#include "defBF51x_base.h" + +#endif /* _DEF_BF512_H */ diff --git a/arch/blackfin/mach-bf518/include/mach/defBF514.h b/arch/blackfin/mach-bf518/include/mach/defBF514.h new file mode 100644 index 00000000000..543f2913b3f --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/defBF514.h @@ -0,0 +1,113 @@ +/* + * File: include/asm-blackfin/mach-bf518/defBF514.h + * Based on: + * Author: + * + * Created: + * Description: + * + * Rev: + * + * Modified: + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _DEF_BF514_H +#define _DEF_BF514_H + +/* Include all Core registers and bit definitions */ +#include <asm/def_LPBlackfin.h> + +/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF514 */ + +/* Include defBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */ +#include "defBF51x_base.h" + +/* The following are the #defines needed by ADSP-BF514 that are not in the common header */ + +/* SDH Registers */ + +#define SDH_PWR_CTL 0xFFC03900 /* SDH Power Control */ +#define SDH_CLK_CTL 0xFFC03904 /* SDH Clock Control */ +#define SDH_ARGUMENT 0xFFC03908 /* SDH Argument */ +#define SDH_COMMAND 0xFFC0390C /* SDH Command */ +#define SDH_RESP_CMD 0xFFC03910 /* SDH Response Command */ +#define SDH_RESPONSE0 0xFFC03914 /* SDH Response0 */ +#define SDH_RESPONSE1 0xFFC03918 /* SDH Response1 */ +#define SDH_RESPONSE2 0xFFC0391C /* SDH Response2 */ +#define SDH_RESPONSE3 0xFFC03920 /* SDH Response3 */ +#define SDH_DATA_TIMER 0xFFC03924 /* SDH Data Timer */ +#define SDH_DATA_LGTH 0xFFC03928 /* SDH Data Length */ +#define SDH_DATA_CTL 0xFFC0392C /* SDH Data Control */ +#define SDH_DATA_CNT 0xFFC03930 /* SDH Data Counter */ +#define SDH_STATUS 0xFFC03934 /* SDH Status */ +#define SDH_STATUS_CLR 0xFFC03938 /* SDH Status Clear */ +#define SDH_MASK0 0xFFC0393C /* SDH Interrupt0 Mask */ +#define SDH_MASK1 0xFFC03940 /* SDH Interrupt1 Mask */ +#define SDH_FIFO_CNT 0xFFC03948 /* SDH FIFO Counter */ +#define SDH_FIFO 0xFFC03980 /* SDH Data FIFO */ +#define SDH_E_STATUS 0xFFC039C0 /* SDH Exception Status */ +#define SDH_E_MASK 0xFFC039C4 /* SDH Exception Mask */ +#define SDH_CFG 0xFFC039C8 /* SDH Configuration */ +#define SDH_RD_WAIT_EN 0xFFC039CC /* SDH Read Wait Enable */ +#define SDH_PID0 0xFFC039D0 /* SDH Peripheral Identification0 */ +#define SDH_PID1 0xFFC039D4 /* SDH Peripheral Identification1 */ +#define SDH_PID2 0xFFC039D8 /* SDH Peripheral Identification2 */ +#define SDH_PID3 0xFFC039DC /* SDH Peripheral Identification3 */ +#define SDH_PID4 0xFFC039E0 /* SDH Peripheral Identification4 */ +#define SDH_PID5 0xFFC039E4 /* SDH Peripheral Identification5 */ +#define SDH_PID6 0xFFC039E8 /* SDH Peripheral Identification6 */ +#define SDH_PID7 0xFFC039EC /* SDH Peripheral Identification7 */ + +/* Removable Storage Interface Registers */ + +#define RSI_PWR_CONTROL 0xFFC03800 /* RSI Power Control Register */ +#define RSI_CLK_CONTROL 0xFFC03804 /* RSI Clock Control Register */ +#define RSI_ARGUMENT 0xFFC03808 /* RSI Argument Register */ +#define RSI_COMMAND 0xFFC0380C /* RSI Command Register */ +#define RSI_RESP_CMD 0xFFC03810 /* RSI Response Command Register */ +#define RSI_RESPONSE0 0xFFC03814 /* RSI Response Register */ +#define RSI_RESPONSE1 0xFFC03818 /* RSI Response Register */ +#define RSI_RESPONSE2 0xFFC0381C /* RSI Response Register */ +#define RSI_RESPONSE3 0xFFC03820 /* RSI Response Register */ +#define RSI_DATA_TIMER 0xFFC03824 /* RSI Data Timer Register */ +#define RSI_DATA_LGTH 0xFFC03828 /* RSI Data Length Register */ +#define RSI_DATA_CONTROL 0xFFC0382C /* RSI Data Control Register */ +#define RSI_DATA_CNT 0xFFC03830 /* RSI Data Counter Register */ +#define RSI_STATUS 0xFFC03834 /* RSI Status Register */ +#define RSI_STATUSCL 0xFFC03838 /* RSI Status Clear Register */ +#define RSI_MASK0 0xFFC0383C /* RSI Interrupt 0 Mask Register */ +#define RSI_MASK1 0xFFC03840 /* RSI Interrupt 1 Mask Register */ +#define RSI_FIFO_CNT 0xFFC03848 /* RSI FIFO Counter Register */ +#define RSI_CEATA_CONTROL 0xFFC0384C /* RSI CEATA Register */ +#define RSI_FIFO 0xFFC03880 /* RSI Data FIFO Register */ +#define RSI_ESTAT 0xFFC038C0 /* RSI Exception Status Register */ +#define RSI_EMASK 0xFFC038C4 /* RSI Exception Mask Register */ +#define RSI_CONFIG 0xFFC038C8 /* RSI Configuration Register */ +#define RSI_RD_WAIT_EN 0xFFC038CC /* RSI Read Wait Enable Register */ +#define RSI_PID0 0xFFC03FE0 /* RSI Peripheral ID Register 0 */ +#define RSI_PID1 0xFFC03FE4 /* RSI Peripheral ID Register 1 */ +#define RSI_PID2 0xFFC03FE8 /* RSI Peripheral ID Register 2 */ +#define RSI_PID3 0xFFC03FEC /* RSI Peripheral ID Register 3 */ +#define RSI_PID4 0xFFC03FF0 /* RSI Peripheral ID Register 4 */ +#define RSI_PID5 0xFFC03FF4 /* RSI Peripheral ID Register 5 */ +#define RSI_PID6 0xFFC03FF8 /* RSI Peripheral ID Register 6 */ +#define RSI_PID7 0xFFC03FFC /* RSI Peripheral ID Register 7 */ + +#endif /* _DEF_BF514_H */ diff --git a/arch/blackfin/mach-bf518/include/mach/defBF516.h b/arch/blackfin/mach-bf518/include/mach/defBF516.h new file mode 100644 index 00000000000..149a269306c --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/defBF516.h @@ -0,0 +1,490 @@ +/* + * File: include/asm-blackfin/mach-bf518/defBF516.h + * Based on: + * Author: + * + * Created: + * Description: + * + * Rev: + * + * Modified: + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _DEF_BF516_H +#define _DEF_BF516_H + +/* Include all Core registers and bit definitions */ +#include <asm/def_LPBlackfin.h> + +/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF516 */ + +/* Include defBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */ +#include "defBF51x_base.h" + +/* The following are the #defines needed by ADSP-BF516 that are not in the common header */ +/* 10/100 Ethernet Controller (0xFFC03000 - 0xFFC031FF) */ + +#define EMAC_OPMODE 0xFFC03000 /* Operating Mode Register */ +#define EMAC_ADDRLO 0xFFC03004 /* Address Low (32 LSBs) Register */ +#define EMAC_ADDRHI 0xFFC03008 /* Address High (16 MSBs) Register */ +#define EMAC_HASHLO 0xFFC0300C /* Multicast Hash Table Low (Bins 31-0) Register */ +#define EMAC_HASHHI 0xFFC03010 /* Multicast Hash Table High (Bins 63-32) Register */ +#define EMAC_STAADD 0xFFC03014 /* Station Management Address Register */ +#define EMAC_STADAT 0xFFC03018 /* Station Management Data Register */ +#define EMAC_FLC 0xFFC0301C /* Flow Control Register */ +#define EMAC_VLAN1 0xFFC03020 /* VLAN1 Tag Register */ +#define EMAC_VLAN2 0xFFC03024 /* VLAN2 Tag Register */ +#define EMAC_WKUP_CTL 0xFFC0302C /* Wake-Up Control/Status Register */ +#define EMAC_WKUP_FFMSK0 0xFFC03030 /* Wake-Up Frame Filter 0 Byte Mask Register */ +#define EMAC_WKUP_FFMSK1 0xFFC03034 /* Wake-Up Frame Filter 1 Byte Mask Register */ +#define EMAC_WKUP_FFMSK2 0xFFC03038 /* Wake-Up Frame Filter 2 Byte Mask Register */ +#define EMAC_WKUP_FFMSK3 0xFFC0303C /* Wake-Up Frame Filter 3 Byte Mask Register */ +#define EMAC_WKUP_FFCMD 0xFFC03040 /* Wake-Up Frame Filter Commands Register */ +#define EMAC_WKUP_FFOFF 0xFFC03044 /* Wake-Up Frame Filter Offsets Register */ +#define EMAC_WKUP_FFCRC0 0xFFC03048 /* Wake-Up Frame Filter 0,1 CRC-16 Register */ +#define EMAC_WKUP_FFCRC1 0xFFC0304C /* Wake-Up Frame Filter 2,3 CRC-16 Register */ + +#define EMAC_SYSCTL 0xFFC03060 /* EMAC System Control Register */ +#define EMAC_SYSTAT 0xFFC03064 /* EMAC System Status Register */ +#define EMAC_RX_STAT 0xFFC03068 /* RX Current Frame Status Register */ +#define EMAC_RX_STKY 0xFFC0306C /* RX Sticky Frame Status Register */ +#define EMAC_RX_IRQE 0xFFC03070 /* RX Frame Status Interrupt Enables Register */ +#define EMAC_TX_STAT 0xFFC03074 /* TX Current Frame Status Register */ +#define EMAC_TX_STKY 0xFFC03078 /* TX Sticky Frame Status Register */ +#define EMAC_TX_IRQE 0xFFC0307C /* TX Frame Status Interrupt Enables Register */ + +#define EMAC_MMC_CTL 0xFFC03080 /* MMC Counter Control Register */ +#define EMAC_MMC_RIRQS 0xFFC03084 /* MMC RX Interrupt Status Register */ +#define EMAC_MMC_RIRQE 0xFFC03088 /* MMC RX Interrupt Enables Register */ +#define EMAC_MMC_TIRQS 0xFFC0308C /* MMC TX Interrupt Status Register */ +#define EMAC_MMC_TIRQE 0xFFC03090 /* MMC TX Interrupt Enables Register */ + +#define EMAC_RXC_OK 0xFFC03100 /* RX Frame Successful Count */ +#define EMAC_RXC_FCS 0xFFC03104 /* RX Frame FCS Failure Count */ +#define EMAC_RXC_ALIGN 0xFFC03108 /* RX Alignment Error Count */ +#define EMAC_RXC_OCTET 0xFFC0310C /* RX Octets Successfully Received Count */ +#define EMAC_RXC_DMAOVF 0xFFC03110 /* Internal MAC Sublayer Error RX Frame Count */ +#define EMAC_RXC_UNICST 0xFFC03114 /* Unicast RX Frame Count */ +#define EMAC_RXC_MULTI 0xFFC03118 /* Multicast RX Frame Count */ +#define EMAC_RXC_BROAD 0xFFC0311C /* Broadcast RX Frame Count */ +#define EMAC_RXC_LNERRI 0xFFC03120 /* RX Frame In Range Error Count */ +#define EMAC_RXC_LNERRO 0xFFC03124 /* RX Frame Out Of Range Error Count */ +#define EMAC_RXC_LONG 0xFFC03128 /* RX Frame Too Long Count */ +#define EMAC_RXC_MACCTL 0xFFC0312C /* MAC Control RX Frame Count */ +#define EMAC_RXC_OPCODE 0xFFC03130 /* Unsupported Op-Code RX Frame Count */ +#define EMAC_RXC_PAUSE 0xFFC03134 /* MAC Control Pause RX Frame Count */ +#define EMAC_RXC_ALLFRM 0xFFC03138 /* Overall RX Frame Count */ +#define EMAC_RXC_ALLOCT 0xFFC0313C /* Overall RX Octet Count */ +#define EMAC_RXC_TYPED 0xFFC03140 /* Type/Length Consistent RX Frame Count */ +#define EMAC_RXC_SHORT 0xFFC03144 /* RX Frame Fragment Count - Byte Count x < 64 */ +#define EMAC_RXC_EQ64 0xFFC03148 /* Good RX Frame Count - Byte Count x = 64 */ +#define EMAC_RXC_LT128 0xFFC0314C /* Good RX Frame Count - Byte Count 64 < x < 128 */ +#define EMAC_RXC_LT256 0xFFC03150 /* Good RX Frame Count - Byte Count 128 <= x < 256 */ +#define EMAC_RXC_LT512 0xFFC03154 /* Good RX Frame Count - Byte Count 256 <= x < 512 */ +#define EMAC_RXC_LT1024 0xFFC03158 /* Good RX Frame Count - Byte Count 512 <= x < 1024 */ +#define EMAC_RXC_GE1024 0xFFC0315C /* Good RX Frame Count - Byte Count x >= 1024 */ + +#define EMAC_TXC_OK 0xFFC03180 /* TX Frame Successful Count */ +#define EMAC_TXC_1COL 0xFFC03184 /* TX Frames Successful After Single Collision Count */ +#define EMAC_TXC_GT1COL 0xFFC03188 /* TX Frames Successful After Multiple Collisions Count */ +#define EMAC_TXC_OCTET 0xFFC0318C /* TX Octets Successfully Received Count */ +#define EMAC_TXC_DEFER 0xFFC03190 /* TX Frame Delayed Due To Busy Count */ +#define EMAC_TXC_LATECL 0xFFC03194 /* Late TX Collisions Count */ +#define EMAC_TXC_XS_COL 0xFFC03198 /* TX Frame Failed Due To Excessive Collisions Count */ +#define EMAC_TXC_DMAUND 0xFFC0319C /* Internal MAC Sublayer Error TX Frame Count */ +#define EMAC_TXC_CRSERR 0xFFC031A0 /* Carrier Sense Deasserted During TX Frame Count */ +#define EMAC_TXC_UNICST 0xFFC031A4 /* Unicast TX Frame Count */ +#define EMAC_TXC_MULTI 0xFFC031A8 /* Multicast TX Frame Count */ +#define EMAC_TXC_BROAD 0xFFC031AC /* Broadcast TX Frame Count */ +#define EMAC_TXC_XS_DFR 0xFFC031B0 /* TX Frames With Excessive Deferral Count */ +#define EMAC_TXC_MACCTL 0xFFC031B4 /* MAC Control TX Frame Count */ +#define EMAC_TXC_ALLFRM 0xFFC031B8 /* Overall TX Frame Count */ +#define EMAC_TXC_ALLOCT 0xFFC031BC /* Overall TX Octet Count */ +#define EMAC_TXC_EQ64 0xFFC031C0 /* Good TX Frame Count - Byte Count x = 64 */ +#define EMAC_TXC_LT128 0xFFC031C4 /* Good TX Frame Count - Byte Count 64 < x < 128 */ +#define EMAC_TXC_LT256 0xFFC031C8 /* Good TX Frame Count - Byte Count 128 <= x < 256 */ +#define EMAC_TXC_LT512 0xFFC031CC /* Good TX Frame Count - Byte Count 256 <= x < 512 */ +#define EMAC_TXC_LT1024 0xFFC031D0 /* Good TX Frame Count - Byte Count 512 <= x < 1024 */ +#define EMAC_TXC_GE1024 0xFFC031D4 /* Good TX Frame Count - Byte Count x >= 1024 */ +#define EMAC_TXC_ABORT 0xFFC031D8 /* Total TX Frames Aborted Count */ + +/* Listing for IEEE-Supported Count Registers */ + +#define FramesReceivedOK EMAC_RXC_OK /* RX Frame Successful Count */ +#define FrameCheckSequenceErrors EMAC_RXC_FCS /* RX Frame FCS Failure Count */ +#define AlignmentErrors EMAC_RXC_ALIGN /* RX Alignment Error Count */ +#define OctetsReceivedOK EMAC_RXC_OCTET /* RX Octets Successfully Received Count */ +#define FramesLostDueToIntMACRcvError EMAC_RXC_DMAOVF /* Internal MAC Sublayer Error RX Frame Count */ +#define UnicastFramesReceivedOK EMAC_RXC_UNICST /* Unicast RX Frame Count */ +#define MulticastFramesReceivedOK EMAC_RXC_MULTI /* Multicast RX Frame Count */ +#define BroadcastFramesReceivedOK EMAC_RXC_BROAD /* Broadcast RX Frame Count */ +#define InRangeLengthErrors EMAC_RXC_LNERRI /* RX Frame In Range Error Count */ +#define OutOfRangeLengthField EMAC_RXC_LNERRO /* RX Frame Out Of Range Error Count */ +#define FrameTooLongErrors EMAC_RXC_LONG /* RX Frame Too Long Count */ +#define MACControlFramesReceived EMAC_RXC_MACCTL /* MAC Control RX Frame Count */ +#define UnsupportedOpcodesReceived EMAC_RXC_OPCODE /* Unsupported Op-Code RX Frame Count */ +#define PAUSEMACCtrlFramesReceived EMAC_RXC_PAUSE /* MAC Control Pause RX Frame Count */ +#define FramesReceivedAll EMAC_RXC_ALLFRM /* Overall RX Frame Count */ +#define OctetsReceivedAll EMAC_RXC_ALLOCT /* Overall RX Octet Count */ +#define TypedFramesReceived EMAC_RXC_TYPED /* Type/Length Consistent RX Frame Count */ +#define FramesLenLt64Received EMAC_RXC_SHORT /* RX Frame Fragment Count - Byte Count x < 64 */ +#define FramesLenEq64Received EMAC_RXC_EQ64 /* Good RX Frame Count - Byte Count x = 64 */ +#define FramesLen65_127Received EMAC_RXC_LT128 /* Good RX Frame Count - Byte Count 64 < x < 128 */ +#define FramesLen128_255Received EMAC_RXC_LT256 /* Good RX Frame Count - Byte Count 128 <= x < 256 */ +#define FramesLen256_511Received EMAC_RXC_LT512 /* Good RX Frame Count - Byte Count 256 <= x < 512 */ +#define FramesLen512_1023Received EMAC_RXC_LT1024 /* Good RX Frame Count - Byte Count 512 <= x < 1024 */ +#define FramesLen1024_MaxReceived EMAC_RXC_GE1024 /* Good RX Frame Count - Byte Count x >= 1024 */ + +#define FramesTransmittedOK EMAC_TXC_OK /* TX Frame Successful Count */ +#define SingleCollisionFrames EMAC_TXC_1COL /* TX Frames Successful After Single Collision Count */ +#define MultipleCollisionFrames EMAC_TXC_GT1COL /* TX Frames Successful After Multiple Collisions Count */ +#define OctetsTransmittedOK EMAC_TXC_OCTET /* TX Octets Successfully Received Count */ +#define FramesWithDeferredXmissions EMAC_TXC_DEFER /* TX Frame Delayed Due To Busy Count */ +#define LateCollisions EMAC_TXC_LATECL /* Late TX Collisions Count */ +#define FramesAbortedDueToXSColls EMAC_TXC_XS_COL /* TX Frame Failed Due To Excessive Collisions Count */ +#define FramesLostDueToIntMacXmitError EMAC_TXC_DMAUND /* Internal MAC Sublayer Error TX Frame Count */ +#define CarrierSenseErrors EMAC_TXC_CRSERR /* Carrier Sense Deasserted During TX Frame Count */ +#define UnicastFramesXmittedOK EMAC_TXC_UNICST /* Unicast TX Frame Count */ +#define MulticastFramesXmittedOK EMAC_TXC_MULTI /* Multicast TX Frame Count */ +#define BroadcastFramesXmittedOK EMAC_TXC_BROAD /* Broadcast TX Frame Count */ +#define FramesWithExcessiveDeferral EMAC_TXC_XS_DFR /* TX Frames With Excessive Deferral Count */ +#define MACControlFramesTransmitted EMAC_TXC_MACCTL /* MAC Control TX Frame Count */ +#define FramesTransmittedAll EMAC_TXC_ALLFRM /* Overall TX Frame Count */ +#define OctetsTransmittedAll EMAC_TXC_ALLOCT /* Overall TX Octet Count */ +#define FramesLenEq64Transmitted EMAC_TXC_EQ64 /* Good TX Frame Count - Byte Count x = 64 */ +#define FramesLen65_127Transmitted EMAC_TXC_LT128 /* Good TX Frame Count - Byte Count 64 < x < 128 */ +#define FramesLen128_255Transmitted EMAC_TXC_LT256 /* Good TX Frame Count - Byte Count 128 <= x < 256 */ +#define FramesLen256_511Transmitted EMAC_TXC_LT512 /* Good TX Frame Count - Byte Count 256 <= x < 512 */ +#define FramesLen512_1023Transmitted EMAC_TXC_LT1024 /* Good TX Frame Count - Byte Count 512 <= x < 1024 */ +#define FramesLen1024_MaxTransmitted EMAC_TXC_GE1024 /* Good TX Frame Count - Byte Count x >= 1024 */ +#define TxAbortedFrames EMAC_TXC_ABORT /* Total TX Frames Aborted Count */ + +/*********************************************************************************** +** System MMR Register Bits And Macros +** +** Disclaimer: All macros are intended to make C and Assembly code more readable. +** Use these macros carefully, as any that do left shifts for field +** depositing will result in the lower order bits being destroyed. Any +** macro that shifts left to properly position the bit-field should be +** used as part of an OR to initialize a register and NOT as a dynamic +** modifier UNLESS the lower order bits are saved and ORed back in when +** the macro is used. +*************************************************************************************/ + +/************************ ETHERNET 10/100 CONTROLLER MASKS ************************/ + +/* EMAC_OPMODE Masks */ + +#define RE 0x00000001 /* Receiver Enable */ +#define ASTP 0x00000002 /* Enable Automatic Pad Stripping On RX Frames */ +#define HU 0x00000010 /* Hash Filter Unicast Address */ +#define HM 0x00000020 /* Hash Filter Multicast Address */ +#define PAM 0x00000040 /* Pass-All-Multicast Mode Enable */ +#define PR 0x00000080 /* Promiscuous Mode Enable */ +#define IFE 0x00000100 /* Inverse Filtering Enable */ +#define DBF 0x00000200 /* Disable Broadcast Frame Reception */ +#define PBF 0x00000400 /* Pass Bad Frames Enable */ +#define PSF 0x00000800 /* Pass Short Frames Enable */ +#define RAF 0x00001000 /* Receive-All Mode */ +#define TE 0x00010000 /* Transmitter Enable */ +#define DTXPAD 0x00020000 /* Disable Automatic TX Padding */ +#define DTXCRC 0x00040000 /* Disable Automatic TX CRC Generation */ +#define DC 0x00080000 /* Deferral Check */ +#define BOLMT 0x00300000 /* Back-Off Limit */ +#define BOLMT_10 0x00000000 /* 10-bit range */ +#define BOLMT_8 0x00100000 /* 8-bit range */ +#define BOLMT_4 0x00200000 /* 4-bit range */ +#define BOLMT_1 0x00300000 /* 1-bit range */ +#define DRTY 0x00400000 /* Disable TX Retry On Collision */ +#define LCTRE 0x00800000 /* Enable TX Retry On Late Collision */ +#define RMII 0x01000000 /* RMII/MII* Mode */ +#define RMII_10 0x02000000 /* Speed Select for RMII Port (10MBit/100MBit*) */ +#define FDMODE 0x04000000 /* Duplex Mode Enable (Full/Half*) */ +#define LB 0x08000000 /* Internal Loopback Enable */ +#define DRO 0x10000000 /* Disable Receive Own Frames (Half-Duplex Mode) */ + +/* EMAC_STAADD Masks */ + +#define STABUSY 0x00000001 /* Initiate Station Mgt Reg Access / STA Busy Stat */ +#define STAOP 0x00000002 /* Station Management Operation Code (Write/Read*) */ +#define STADISPRE 0x00000004 /* Disable Preamble Generation */ +#define STAIE 0x00000008 /* Station Mgt. Transfer Done Interrupt Enable */ +#define REGAD 0x000007C0 /* STA Register Address */ +#define PHYAD 0x0000F800 /* PHY Device Address */ + +#define SET_REGAD(x) (((x)&0x1F)<< 6 ) /* Set STA Register Address */ +#define SET_PHYAD(x) (((x)&0x1F)<< 11 ) /* Set PHY Device Address */ + +/* EMAC_STADAT Mask */ + +#define STADATA 0x0000FFFF /* Station Management Data */ + +/* EMAC_FLC Masks */ + +#define FLCBUSY 0x00000001 /* Send Flow Ctrl Frame / Flow Ctrl Busy Status */ +#define FLCE 0x00000002 /* Flow Control Enable */ +#define PCF 0x00000004 /* Pass Control Frames */ +#define BKPRSEN 0x00000008 /* Enable Backpressure */ +#define FLCPAUSE 0xFFFF0000 /* Pause Time */ + +#define SET_FLCPAUSE(x) (((x)&0xFFFF)<< 16) /* Set Pause Time */ + +/* EMAC_WKUP_CTL Masks */ + +#define CAPWKFRM 0x00000001 /* Capture Wake-Up Frames */ +#define MPKE 0x00000002 /* Magic Packet Enable */ +#define RWKE 0x00000004 /* Remote Wake-Up Frame Enable */ +#define GUWKE 0x00000008 /* Global Unicast Wake Enable */ +#define MPKS 0x00000020 /* Magic Packet Received Status */ +#define RWKS 0x00000F00 /* Wake-Up Frame Received Status, Filters 3:0 */ + +/* EMAC_WKUP_FFCMD Masks */ + +#define WF0_E 0x00000001 /* Enable Wake-Up Filter 0 */ +#define WF0_T 0x00000008 /* Wake-Up Filter 0 Addr Type (Multicast/Unicast*) */ +#define WF1_E 0x00000100 /* Enable Wake-Up Filter 1 */ +#define WF1_T 0x00000800 /* Wake-Up Filter 1 Addr Type (Multicast/Unicast*) */ +#define WF2_E 0x00010000 /* Enable Wake-Up Filter 2 */ +#define WF2_T 0x00080000 /* Wake-Up Filter 2 Addr Type (Multicast/Unicast*) */ +#define WF3_E 0x01000000 /* Enable Wake-Up Filter 3 */ +#define WF3_T 0x08000000 /* Wake-Up Filter 3 Addr Type (Multicast/Unicast*) */ + +/* EMAC_WKUP_FFOFF Masks */ + +#define WF0_OFF 0x000000FF /* Wake-Up Filter 0 Pattern Offset */ +#define WF1_OFF 0x0000FF00 /* Wake-Up Filter 1 Pattern Offset */ +#define WF2_OFF 0x00FF0000 /* Wake-Up Filter 2 Pattern Offset */ +#define WF3_OFF 0xFF000000 /* Wake-Up Filter 3 Pattern Offset */ + +#define SET_WF0_OFF(x) (((x)&0xFF)<< 0 ) /* Set Wake-Up Filter 0 Byte Offset */ +#define SET_WF1_OFF(x) (((x)&0xFF)<< 8 ) /* Set Wake-Up Filter 1 Byte Offset */ +#define SET_WF2_OFF(x) (((x)&0xFF)<< 16 ) /* Set Wake-Up Filter 2 Byte Offset */ +#define SET_WF3_OFF(x) (((x)&0xFF)<< 24 ) /* Set Wake-Up Filter 3 Byte Offset */ +/* Set ALL Offsets */ +#define SET_WF_OFFS(x0,x1,x2,x3) (SET_WF0_OFF((x0))|SET_WF1_OFF((x1))|SET_WF2_OFF((x2))|SET_WF3_OFF((x3))) + +/* EMAC_WKUP_FFCRC0 Masks */ + +#define WF0_CRC 0x0000FFFF /* Wake-Up Filter 0 Pattern CRC */ +#define WF1_CRC 0xFFFF0000 /* Wake-Up Filter 1 Pattern CRC */ + +#define SET_WF0_CRC(x) (((x)&0xFFFF)<< 0 ) /* Set Wake-Up Filter 0 Target CRC */ +#define SET_WF1_CRC(x) (((x)&0xFFFF)<< 16 ) /* Set Wake-Up Filter 1 Target CRC */ + +/* EMAC_WKUP_FFCRC1 Masks */ + +#define WF2_CRC 0x0000FFFF /* Wake-Up Filter 2 Pattern CRC */ +#define WF3_CRC 0xFFFF0000 /* Wake-Up Filter 3 Pattern CRC */ + +#define SET_WF2_CRC(x) (((x)&0xFFFF)<< 0 ) /* Set Wake-Up Filter 2 Target CRC */ +#define SET_WF3_CRC(x) (((x)&0xFFFF)<< 16 ) /* Set Wake-Up Filter 3 Target CRC */ + +/* EMAC_SYSCTL Masks */ + +#define PHYIE 0x00000001 /* PHY_INT Interrupt Enable */ +#define RXDWA 0x00000002 /* Receive Frame DMA Word Alignment (Odd/Even*) */ +#define RXCKS 0x00000004 /* Enable RX Frame TCP/UDP Checksum Computation */ +#define TXDWA 0x00000010 /* Transmit Frame DMA Word Alignment (Odd/Even*) */ +#define MDCDIV 0x00003F00 /* SCLK:MDC Clock Divisor [MDC=SCLK/(2*(N+1))] */ + +#define SET_MDCDIV(x) (((x)&0x3F)<< 8) /* Set MDC Clock Divisor */ + +/* EMAC_SYSTAT Masks */ + +#define PHYINT 0x00000001 /* PHY_INT Interrupt Status */ +#define MMCINT 0x00000002 /* MMC Counter Interrupt Status */ +#define RXFSINT 0x00000004 /* RX Frame-Status Interrupt Status */ +#define TXFSINT 0x00000008 /* TX Frame-Status Interrupt Status */ +#define WAKEDET 0x00000010 /* Wake-Up Detected Status */ +#define RXDMAERR 0x00000020 /* RX DMA Direction Error Status */ +#define TXDMAERR 0x00000040 /* TX DMA Direction Error Status */ +#define STMDONE 0x00000080 /* Station Mgt. Transfer Done Interrupt Status */ + +/* EMAC_RX_STAT, EMAC_RX_STKY, and EMAC_RX_IRQE Masks */ + +#define RX_FRLEN 0x000007FF /* Frame Length In Bytes */ +#define RX_COMP 0x00001000 /* RX Frame Complete */ +#define RX_OK 0x00002000 /* RX Frame Received With No Errors */ +#define RX_LONG 0x00004000 /* RX Frame Too Long Error */ +#define RX_ALIGN 0x00008000 /* RX Frame Alignment Error */ +#define RX_CRC 0x00010000 /* RX Frame CRC Error */ +#define RX_LEN 0x00020000 /* RX Frame Length Error */ +#define RX_FRAG 0x00040000 /* RX Frame Fragment Error */ +#define RX_ADDR 0x00080000 /* RX Frame Address Filter Failed Error */ +#define RX_DMAO 0x00100000 /* RX Frame DMA Overrun Error */ +#define RX_PHY 0x00200000 /* RX Frame PHY Error */ +#define RX_LATE 0x00400000 /* RX Frame Late Collision Error */ +#define RX_RANGE 0x00800000 /* RX Frame Length Field Out of Range Error */ +#define RX_MULTI 0x01000000 /* RX Multicast Frame Indicator */ +#define RX_BROAD 0x02000000 /* RX Broadcast Frame Indicator */ +#define RX_CTL 0x04000000 /* RX Control Frame Indicator */ +#define RX_UCTL 0x08000000 /* Unsupported RX Control Frame Indicator */ +#define RX_TYPE 0x10000000 /* RX Typed Frame Indicator */ +#define RX_VLAN1 0x20000000 /* RX VLAN1 Frame Indicator */ +#define RX_VLAN2 0x40000000 /* RX VLAN2 Frame Indicator */ +#define RX_ACCEPT 0x80000000 /* RX Frame Accepted Indicator */ + +/* EMAC_TX_STAT, EMAC_TX_STKY, and EMAC_TX_IRQE Masks */ + +#define TX_COMP 0x00000001 /* TX Frame Complete */ +#define TX_OK 0x00000002 /* TX Frame Sent With No Errors */ +#define TX_ECOLL 0x00000004 /* TX Frame Excessive Collision Error */ +#define TX_LATE 0x00000008 /* TX Frame Late Collision Error */ +#define TX_DMAU 0x00000010 /* TX Frame DMA Underrun Error (STAT) */ +#define TX_MACE 0x00000010 /* Internal MAC Error Detected (STKY and IRQE) */ +#define TX_EDEFER 0x00000020 /* TX Frame Excessive Deferral Error */ +#define TX_BROAD 0x00000040 /* TX Broadcast Frame Indicator */ +#define TX_MULTI 0x00000080 /* TX Multicast Frame Indicator */ +#define TX_CCNT 0x00000F00 /* TX Frame Collision Count */ +#define TX_DEFER 0x00001000 /* TX Frame Deferred Indicator */ +#define TX_CRS 0x00002000 /* TX Frame Carrier Sense Not Asserted Error */ +#define TX_LOSS 0x00004000 /* TX Frame Carrier Lost During TX Error */ +#define TX_RETRY 0x00008000 /* TX Frame Successful After Retry */ +#define TX_FRLEN 0x07FF0000 /* TX Frame Length (Bytes) */ + +/* EMAC_MMC_CTL Masks */ +#define RSTC 0x00000001 /* Reset All Counters */ +#define CROLL 0x00000002 /* Counter Roll-Over Enable */ +#define CCOR 0x00000004 /* Counter Clear-On-Read Mode Enable */ +#define MMCE 0x00000008 /* Enable MMC Counter Operation */ + +/* EMAC_MMC_RIRQS and EMAC_MMC_RIRQE Masks */ +#define RX_OK_CNT 0x00000001 /* RX Frames Received With No Errors */ +#define RX_FCS_CNT 0x00000002 /* RX Frames W/Frame Check Sequence Errors */ +#define RX_ALIGN_CNT 0x00000004 /* RX Frames With Alignment Errors */ +#define RX_OCTET_CNT 0x00000008 /* RX Octets Received OK */ +#define RX_LOST_CNT 0x00000010 /* RX Frames Lost Due To Internal MAC RX Error */ +#define RX_UNI_CNT 0x00000020 /* Unicast RX Frames Received OK */ +#define RX_MULTI_CNT 0x00000040 /* Multicast RX Frames Received OK */ +#define RX_BROAD_CNT 0x00000080 /* Broadcast RX Frames Received OK */ +#define RX_IRL_CNT 0x00000100 /* RX Frames With In-Range Length Errors */ +#define RX_ORL_CNT 0x00000200 /* RX Frames With Out-Of-Range Length Errors */ +#define RX_LONG_CNT 0x00000400 /* RX Frames With Frame Too Long Errors */ +#define RX_MACCTL_CNT 0x00000800 /* MAC Control RX Frames Received */ +#define RX_OPCODE_CTL 0x00001000 /* Unsupported Op-Code RX Frames Received */ +#define RX_PAUSE_CNT 0x00002000 /* PAUSEMAC Control RX Frames Received */ +#define RX_ALLF_CNT 0x00004000 /* All RX Frames Received */ +#define RX_ALLO_CNT 0x00008000 /* All RX Octets Received */ +#define RX_TYPED_CNT 0x00010000 /* Typed RX Frames Received */ +#define RX_SHORT_CNT 0x00020000 /* RX Frame Fragments (< 64 Bytes) Received */ +#define RX_EQ64_CNT 0x00040000 /* 64-Byte RX Frames Received */ +#define RX_LT128_CNT 0x00080000 /* 65-127-Byte RX Frames Received */ +#define RX_LT256_CNT 0x00100000 /* 128-255-Byte RX Frames Received */ +#define RX_LT512_CNT 0x00200000 /* 256-511-Byte RX Frames Received */ +#define RX_LT1024_CNT 0x00400000 /* 512-1023-Byte RX Frames Received */ +#define RX_GE1024_CNT 0x00800000 /* 1024-Max-Byte RX Frames Received */ + +/* EMAC_MMC_TIRQS and EMAC_MMC_TIRQE Masks */ + +#define TX_OK_CNT 0x00000001 /* TX Frames Sent OK */ +#define TX_SCOLL_CNT 0x00000002 /* TX Frames With Single Collisions */ +#define TX_MCOLL_CNT 0x00000004 /* TX Frames With Multiple Collisions */ +#define TX_OCTET_CNT 0x00000008 /* TX Octets Sent OK */ +#define TX_DEFER_CNT 0x00000010 /* TX Frames With Deferred Transmission */ +#define TX_LATE_CNT 0x00000020 /* TX Frames With Late Collisions */ +#define TX_ABORTC_CNT 0x00000040 /* TX Frames Aborted Due To Excess Collisions */ +#define TX_LOST_CNT 0x00000080 /* TX Frames Lost Due To Internal MAC TX Error */ +#define TX_CRS_CNT 0x00000100 /* TX Frames With Carrier Sense Errors */ +#define TX_UNI_CNT 0x00000200 /* Unicast TX Frames Sent */ +#define TX_MULTI_CNT 0x00000400 /* Multicast TX Frames Sent */ +#define TX_BROAD_CNT 0x00000800 /* Broadcast TX Frames Sent */ +#define TX_EXDEF_CTL 0x00001000 /* TX Frames With Excessive Deferral */ +#define TX_MACCTL_CNT 0x00002000 /* MAC Control TX Frames Sent */ +#define TX_ALLF_CNT 0x00004000 /* All TX Frames Sent */ +#define TX_ALLO_CNT 0x00008000 /* All TX Octets Sent */ +#define TX_EQ64_CNT 0x00010000 /* 64-Byte TX Frames Sent */ +#define TX_LT128_CNT 0x00020000 /* 65-127-Byte TX Frames Sent */ +#define TX_LT256_CNT 0x00040000 /* 128-255-Byte TX Frames Sent */ +#define TX_LT512_CNT 0x00080000 /* 256-511-Byte TX Frames Sent */ +#define TX_LT1024_CNT 0x00100000 /* 512-1023-Byte TX Frames Sent */ +#define TX_GE1024_CNT 0x00200000 /* 1024-Max-Byte TX Frames Sent */ +#define TX_ABORT_CNT 0x00400000 /* TX Frames Aborted */ + +/* SDH Registers */ + +#define SDH_PWR_CTL 0xFFC03900 /* SDH Power Control */ +#define SDH_CLK_CTL 0xFFC03904 /* SDH Clock Control */ +#define SDH_ARGUMENT 0xFFC03908 /* SDH Argument */ +#define SDH_COMMAND 0xFFC0390C /* SDH Command */ +#define SDH_RESP_CMD 0xFFC03910 /* SDH Response Command */ +#define SDH_RESPONSE0 0xFFC03914 /* SDH Response0 */ +#define SDH_RESPONSE1 0xFFC03918 /* SDH Response1 */ +#define SDH_RESPONSE2 0xFFC0391C /* SDH Response2 */ +#define SDH_RESPONSE3 0xFFC03920 /* SDH Response3 */ +#define SDH_DATA_TIMER 0xFFC03924 /* SDH Data Timer */ +#define SDH_DATA_LGTH 0xFFC03928 /* SDH Data Length */ +#define SDH_DATA_CTL 0xFFC0392C /* SDH Data Control */ +#define SDH_DATA_CNT 0xFFC03930 /* SDH Data Counter */ +#define SDH_STATUS 0xFFC03934 /* SDH Status */ +#define SDH_STATUS_CLR 0xFFC03938 /* SDH Status Clear */ +#define SDH_MASK0 0xFFC0393C /* SDH Interrupt0 Mask */ +#define SDH_MASK1 0xFFC03940 /* SDH Interrupt1 Mask */ +#define SDH_FIFO_CNT 0xFFC03948 /* SDH FIFO Counter */ +#define SDH_FIFO 0xFFC03980 /* SDH Data FIFO */ +#define SDH_E_STATUS 0xFFC039C0 /* SDH Exception Status */ +#define SDH_E_MASK 0xFFC039C4 /* SDH Exception Mask */ +#define SDH_CFG 0xFFC039C8 /* SDH Configuration */ +#define SDH_RD_WAIT_EN 0xFFC039CC /* SDH Read Wait Enable */ +#define SDH_PID0 0xFFC039D0 /* SDH Peripheral Identification0 */ +#define SDH_PID1 0xFFC039D4 /* SDH Peripheral Identification1 */ +#define SDH_PID2 0xFFC039D8 /* SDH Peripheral Identification2 */ +#define SDH_PID3 0xFFC039DC /* SDH Peripheral Identification3 */ +#define SDH_PID4 0xFFC039E0 /* SDH Peripheral Identification4 */ +#define SDH_PID5 0xFFC039E4 /* SDH Peripheral Identification5 */ +#define SDH_PID6 0xFFC039E8 /* SDH Peripheral Identification6 */ +#define SDH_PID7 0xFFC039EC /* SDH Peripheral Identification7 */ + +/* Removable Storage Interface Registers */ + +#define RSI_PWR_CONTROL 0xFFC03800 /* RSI Power Control Register */ +#define RSI_CLK_CONTROL 0xFFC03804 /* RSI Clock Control Register */ +#define RSI_ARGUMENT 0xFFC03808 /* RSI Argument Register */ +#define RSI_COMMAND 0xFFC0380C /* RSI Command Register */ +#define RSI_RESP_CMD 0xFFC03810 /* RSI Response Command Register */ +#define RSI_RESPONSE0 0xFFC03814 /* RSI Response Register */ +#define RSI_RESPONSE1 0xFFC03818 /* RSI Response Register */ +#define RSI_RESPONSE2 0xFFC0381C /* RSI Response Register */ +#define RSI_RESPONSE3 0xFFC03820 /* RSI Response Register */ +#define RSI_DATA_TIMER 0xFFC03824 /* RSI Data Timer Register */ +#define RSI_DATA_LGTH 0xFFC03828 /* RSI Data Length Register */ +#define RSI_DATA_CONTROL 0xFFC0382C /* RSI Data Control Register */ +#define RSI_DATA_CNT 0xFFC03830 /* RSI Data Counter Register */ +#define RSI_STATUS 0xFFC03834 /* RSI Status Register */ +#define RSI_STATUSCL 0xFFC03838 /* RSI Status Clear Register */ +#define RSI_MASK0 0xFFC0383C /* RSI Interrupt 0 Mask Register */ +#define RSI_MASK1 0xFFC03840 /* RSI Interrupt 1 Mask Register */ +#define RSI_FIFO_CNT 0xFFC03848 /* RSI FIFO Counter Register */ +#define RSI_CEATA_CONTROL 0xFFC0384C /* RSI CEATA Register */ +#define RSI_FIFO 0xFFC03880 /* RSI Data FIFO Register */ +#define RSI_ESTAT 0xFFC038C0 /* RSI Exception Status Register */ +#define RSI_EMASK 0xFFC038C4 /* RSI Exception Mask Register */ +#define RSI_CONFIG 0xFFC038C8 /* RSI Configuration Register */ +#define RSI_RD_WAIT_EN 0xFFC038CC /* RSI Read Wait Enable Register */ +#define RSI_PID0 0xFFC03FE0 /* RSI Peripheral ID Register 0 */ +#define RSI_PID1 0xFFC03FE4 /* RSI Peripheral ID Register 1 */ +#define RSI_PID2 0xFFC03FE8 /* RSI Peripheral ID Register 2 */ +#define RSI_PID3 0xFFC03FEC /* RSI Peripheral ID Register 3 */ +#define RSI_PID4 0xFFC03FF0 /* RSI Peripheral ID Register 4 */ +#define RSI_PID5 0xFFC03FF4 /* RSI Peripheral ID Register 5 */ +#define RSI_PID6 0xFFC03FF8 /* RSI Peripheral ID Register 6 */ +#define RSI_PID7 0xFFC03FFC /* RSI Peripheral ID Register 7 */ + +#endif /* _DEF_BF516_H */ diff --git a/arch/blackfin/mach-bf518/include/mach/defBF518.h b/arch/blackfin/mach-bf518/include/mach/defBF518.h new file mode 100644 index 00000000000..4eaade15dd7 --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/defBF518.h @@ -0,0 +1,516 @@ +/* + * File: include/asm-blackfin/mach-bf518/defBF518.h + * Based on: + * Author: + * + * Created: + * Description: + * + * Rev: + * + * Modified: + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _DEF_BF518_H +#define _DEF_BF518_H + +/* Include all Core registers and bit definitions */ +#include <asm/def_LPBlackfin.h> + +/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF518 */ + +/* Include defBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */ +#include "defBF51x_base.h" + +/* The following are the #defines needed by ADSP-BF518 that are not in the common header */ +/* 10/100 Ethernet Controller (0xFFC03000 - 0xFFC031FF) */ + +#define EMAC_OPMODE 0xFFC03000 /* Operating Mode Register */ +#define EMAC_ADDRLO 0xFFC03004 /* Address Low (32 LSBs) Register */ +#define EMAC_ADDRHI 0xFFC03008 /* Address High (16 MSBs) Register */ +#define EMAC_HASHLO 0xFFC0300C /* Multicast Hash Table Low (Bins 31-0) Register */ +#define EMAC_HASHHI 0xFFC03010 /* Multicast Hash Table High (Bins 63-32) Register */ +#define EMAC_STAADD 0xFFC03014 /* Station Management Address Register */ +#define EMAC_STADAT 0xFFC03018 /* Station Management Data Register */ +#define EMAC_FLC 0xFFC0301C /* Flow Control Register */ +#define EMAC_VLAN1 0xFFC03020 /* VLAN1 Tag Register */ +#define EMAC_VLAN2 0xFFC03024 /* VLAN2 Tag Register */ +#define EMAC_WKUP_CTL 0xFFC0302C /* Wake-Up Control/Status Register */ +#define EMAC_WKUP_FFMSK0 0xFFC03030 /* Wake-Up Frame Filter 0 Byte Mask Register */ +#define EMAC_WKUP_FFMSK1 0xFFC03034 /* Wake-Up Frame Filter 1 Byte Mask Register */ +#define EMAC_WKUP_FFMSK2 0xFFC03038 /* Wake-Up Frame Filter 2 Byte Mask Register */ +#define EMAC_WKUP_FFMSK3 0xFFC0303C /* Wake-Up Frame Filter 3 Byte Mask Register */ +#define EMAC_WKUP_FFCMD 0xFFC03040 /* Wake-Up Frame Filter Commands Register */ +#define EMAC_WKUP_FFOFF 0xFFC03044 /* Wake-Up Frame Filter Offsets Register */ +#define EMAC_WKUP_FFCRC0 0xFFC03048 /* Wake-Up Frame Filter 0,1 CRC-16 Register */ +#define EMAC_WKUP_FFCRC1 0xFFC0304C /* Wake-Up Frame Filter 2,3 CRC-16 Register */ + +#define EMAC_SYSCTL 0xFFC03060 /* EMAC System Control Register */ +#define EMAC_SYSTAT 0xFFC03064 /* EMAC System Status Register */ +#define EMAC_RX_STAT 0xFFC03068 /* RX Current Frame Status Register */ +#define EMAC_RX_STKY 0xFFC0306C /* RX Sticky Frame Status Register */ +#define EMAC_RX_IRQE 0xFFC03070 /* RX Frame Status Interrupt Enables Register */ +#define EMAC_TX_STAT 0xFFC03074 /* TX Current Frame Status Register */ +#define EMAC_TX_STKY 0xFFC03078 /* TX Sticky Frame Status Register */ +#define EMAC_TX_IRQE 0xFFC0307C /* TX Frame Status Interrupt Enables Register */ + +#define EMAC_MMC_CTL 0xFFC03080 /* MMC Counter Control Register */ +#define EMAC_MMC_RIRQS 0xFFC03084 /* MMC RX Interrupt Status Register */ +#define EMAC_MMC_RIRQE 0xFFC03088 /* MMC RX Interrupt Enables Register */ +#define EMAC_MMC_TIRQS 0xFFC0308C /* MMC TX Interrupt Status Register */ +#define EMAC_MMC_TIRQE 0xFFC03090 /* MMC TX Interrupt Enables Register */ + +#define EMAC_RXC_OK 0xFFC03100 /* RX Frame Successful Count */ +#define EMAC_RXC_FCS 0xFFC03104 /* RX Frame FCS Failure Count */ +#define EMAC_RXC_ALIGN 0xFFC03108 /* RX Alignment Error Count */ +#define EMAC_RXC_OCTET 0xFFC0310C /* RX Octets Successfully Received Count */ +#define EMAC_RXC_DMAOVF 0xFFC03110 /* Internal MAC Sublayer Error RX Frame Count */ +#define EMAC_RXC_UNICST 0xFFC03114 /* Unicast RX Frame Count */ +#define EMAC_RXC_MULTI 0xFFC03118 /* Multicast RX Frame Count */ +#define EMAC_RXC_BROAD 0xFFC0311C /* Broadcast RX Frame Count */ +#define EMAC_RXC_LNERRI 0xFFC03120 /* RX Frame In Range Error Count */ +#define EMAC_RXC_LNERRO 0xFFC03124 /* RX Frame Out Of Range Error Count */ +#define EMAC_RXC_LONG 0xFFC03128 /* RX Frame Too Long Count */ +#define EMAC_RXC_MACCTL 0xFFC0312C /* MAC Control RX Frame Count */ +#define EMAC_RXC_OPCODE 0xFFC03130 /* Unsupported Op-Code RX Frame Count */ +#define EMAC_RXC_PAUSE 0xFFC03134 /* MAC Control Pause RX Frame Count */ +#define EMAC_RXC_ALLFRM 0xFFC03138 /* Overall RX Frame Count */ +#define EMAC_RXC_ALLOCT 0xFFC0313C /* Overall RX Octet Count */ +#define EMAC_RXC_TYPED 0xFFC03140 /* Type/Length Consistent RX Frame Count */ +#define EMAC_RXC_SHORT 0xFFC03144 /* RX Frame Fragment Count - Byte Count x < 64 */ +#define EMAC_RXC_EQ64 0xFFC03148 /* Good RX Frame Count - Byte Count x = 64 */ +#define EMAC_RXC_LT128 0xFFC0314C /* Good RX Frame Count - Byte Count 64 < x < 128 */ +#define EMAC_RXC_LT256 0xFFC03150 /* Good RX Frame Count - Byte Count 128 <= x < 256 */ +#define EMAC_RXC_LT512 0xFFC03154 /* Good RX Frame Count - Byte Count 256 <= x < 512 */ +#define EMAC_RXC_LT1024 0xFFC03158 /* Good RX Frame Count - Byte Count 512 <= x < 1024 */ +#define EMAC_RXC_GE1024 0xFFC0315C /* Good RX Frame Count - Byte Count x >= 1024 */ + +#define EMAC_TXC_OK 0xFFC03180 /* TX Frame Successful Count */ +#define EMAC_TXC_1COL 0xFFC03184 /* TX Frames Successful After Single Collision Count */ +#define EMAC_TXC_GT1COL 0xFFC03188 /* TX Frames Successful After Multiple Collisions Count */ +#define EMAC_TXC_OCTET 0xFFC0318C /* TX Octets Successfully Received Count */ +#define EMAC_TXC_DEFER 0xFFC03190 /* TX Frame Delayed Due To Busy Count */ +#define EMAC_TXC_LATECL 0xFFC03194 /* Late TX Collisions Count */ +#define EMAC_TXC_XS_COL 0xFFC03198 /* TX Frame Failed Due To Excessive Collisions Count */ +#define EMAC_TXC_DMAUND 0xFFC0319C /* Internal MAC Sublayer Error TX Frame Count */ +#define EMAC_TXC_CRSERR 0xFFC031A0 /* Carrier Sense Deasserted During TX Frame Count */ +#define EMAC_TXC_UNICST 0xFFC031A4 /* Unicast TX Frame Count */ +#define EMAC_TXC_MULTI 0xFFC031A8 /* Multicast TX Frame Count */ +#define EMAC_TXC_BROAD 0xFFC031AC /* Broadcast TX Frame Count */ +#define EMAC_TXC_XS_DFR 0xFFC031B0 /* TX Frames With Excessive Deferral Count */ +#define EMAC_TXC_MACCTL 0xFFC031B4 /* MAC Control TX Frame Count */ +#define EMAC_TXC_ALLFRM 0xFFC031B8 /* Overall TX Frame Count */ +#define EMAC_TXC_ALLOCT 0xFFC031BC /* Overall TX Octet Count */ +#define EMAC_TXC_EQ64 0xFFC031C0 /* Good TX Frame Count - Byte Count x = 64 */ +#define EMAC_TXC_LT128 0xFFC031C4 /* Good TX Frame Count - Byte Count 64 < x < 128 */ +#define EMAC_TXC_LT256 0xFFC031C8 /* Good TX Frame Count - Byte Count 128 <= x < 256 */ +#define EMAC_TXC_LT512 0xFFC031CC /* Good TX Frame Count - Byte Count 256 <= x < 512 */ +#define EMAC_TXC_LT1024 0xFFC031D0 /* Good TX Frame Count - Byte Count 512 <= x < 1024 */ +#define EMAC_TXC_GE1024 0xFFC031D4 /* Good TX Frame Count - Byte Count x >= 1024 */ +#define EMAC_TXC_ABORT 0xFFC031D8 /* Total TX Frames Aborted Count */ + +/* Listing for IEEE-Supported Count Registers */ + +#define FramesReceivedOK EMAC_RXC_OK /* RX Frame Successful Count */ +#define FrameCheckSequenceErrors EMAC_RXC_FCS /* RX Frame FCS Failure Count */ +#define AlignmentErrors EMAC_RXC_ALIGN /* RX Alignment Error Count */ +#define OctetsReceivedOK EMAC_RXC_OCTET /* RX Octets Successfully Received Count */ +#define FramesLostDueToIntMACRcvError EMAC_RXC_DMAOVF /* Internal MAC Sublayer Error RX Frame Count */ +#define UnicastFramesReceivedOK EMAC_RXC_UNICST /* Unicast RX Frame Count */ +#define MulticastFramesReceivedOK EMAC_RXC_MULTI /* Multicast RX Frame Count */ +#define BroadcastFramesReceivedOK EMAC_RXC_BROAD /* Broadcast RX Frame Count */ +#define InRangeLengthErrors EMAC_RXC_LNERRI /* RX Frame In Range Error Count */ +#define OutOfRangeLengthField EMAC_RXC_LNERRO /* RX Frame Out Of Range Error Count */ +#define FrameTooLongErrors EMAC_RXC_LONG /* RX Frame Too Long Count */ +#define MACControlFramesReceived EMAC_RXC_MACCTL /* MAC Control RX Frame Count */ +#define UnsupportedOpcodesReceived EMAC_RXC_OPCODE /* Unsupported Op-Code RX Frame Count */ +#define PAUSEMACCtrlFramesReceived EMAC_RXC_PAUSE /* MAC Control Pause RX Frame Count */ +#define FramesReceivedAll EMAC_RXC_ALLFRM /* Overall RX Frame Count */ +#define OctetsReceivedAll EMAC_RXC_ALLOCT /* Overall RX Octet Count */ +#define TypedFramesReceived EMAC_RXC_TYPED /* Type/Length Consistent RX Frame Count */ +#define FramesLenLt64Received EMAC_RXC_SHORT /* RX Frame Fragment Count - Byte Count x < 64 */ +#define FramesLenEq64Received EMAC_RXC_EQ64 /* Good RX Frame Count - Byte Count x = 64 */ +#define FramesLen65_127Received EMAC_RXC_LT128 /* Good RX Frame Count - Byte Count 64 < x < 128 */ +#define FramesLen128_255Received EMAC_RXC_LT256 /* Good RX Frame Count - Byte Count 128 <= x < 256 */ +#define FramesLen256_511Received EMAC_RXC_LT512 /* Good RX Frame Count - Byte Count 256 <= x < 512 */ +#define FramesLen512_1023Received EMAC_RXC_LT1024 /* Good RX Frame Count - Byte Count 512 <= x < 1024 */ +#define FramesLen1024_MaxReceived EMAC_RXC_GE1024 /* Good RX Frame Count - Byte Count x >= 1024 */ + +#define FramesTransmittedOK EMAC_TXC_OK /* TX Frame Successful Count */ +#define SingleCollisionFrames EMAC_TXC_1COL /* TX Frames Successful After Single Collision Count */ +#define MultipleCollisionFrames EMAC_TXC_GT1COL /* TX Frames Successful After Multiple Collisions Count */ +#define OctetsTransmittedOK EMAC_TXC_OCTET /* TX Octets Successfully Received Count */ +#define FramesWithDeferredXmissions EMAC_TXC_DEFER /* TX Frame Delayed Due To Busy Count */ +#define LateCollisions EMAC_TXC_LATECL /* Late TX Collisions Count */ +#define FramesAbortedDueToXSColls EMAC_TXC_XS_COL /* TX Frame Failed Due To Excessive Collisions Count */ +#define FramesLostDueToIntMacXmitError EMAC_TXC_DMAUND /* Internal MAC Sublayer Error TX Frame Count */ +#define CarrierSenseErrors EMAC_TXC_CRSERR /* Carrier Sense Deasserted During TX Frame Count */ +#define UnicastFramesXmittedOK EMAC_TXC_UNICST /* Unicast TX Frame Count */ +#define MulticastFramesXmittedOK EMAC_TXC_MULTI /* Multicast TX Frame Count */ +#define BroadcastFramesXmittedOK EMAC_TXC_BROAD /* Broadcast TX Frame Count */ +#define FramesWithExcessiveDeferral EMAC_TXC_XS_DFR /* TX Frames With Excessive Deferral Count */ +#define MACControlFramesTransmitted EMAC_TXC_MACCTL /* MAC Control TX Frame Count */ +#define FramesTransmittedAll EMAC_TXC_ALLFRM /* Overall TX Frame Count */ +#define OctetsTransmittedAll EMAC_TXC_ALLOCT /* Overall TX Octet Count */ +#define FramesLenEq64Transmitted EMAC_TXC_EQ64 /* Good TX Frame Count - Byte Count x = 64 */ +#define FramesLen65_127Transmitted EMAC_TXC_LT128 /* Good TX Frame Count - Byte Count 64 < x < 128 */ +#define FramesLen128_255Transmitted EMAC_TXC_LT256 /* Good TX Frame Count - Byte Count 128 <= x < 256 */ +#define FramesLen256_511Transmitted EMAC_TXC_LT512 /* Good TX Frame Count - Byte Count 256 <= x < 512 */ +#define FramesLen512_1023Transmitted EMAC_TXC_LT1024 /* Good TX Frame Count - Byte Count 512 <= x < 1024 */ +#define FramesLen1024_MaxTransmitted EMAC_TXC_GE1024 /* Good TX Frame Count - Byte Count x >= 1024 */ +#define TxAbortedFrames EMAC_TXC_ABORT /* Total TX Frames Aborted Count */ + +/*********************************************************************************** +** System MMR Register Bits And Macros +** +** Disclaimer: All macros are intended to make C and Assembly code more readable. +** Use these macros carefully, as any that do left shifts for field +** depositing will result in the lower order bits being destroyed. Any +** macro that shifts left to properly position the bit-field should be +** used as part of an OR to initialize a register and NOT as a dynamic +** modifier UNLESS the lower order bits are saved and ORed back in when +** the macro is used. +*************************************************************************************/ + +/************************ ETHERNET 10/100 CONTROLLER MASKS ************************/ + +/* EMAC_OPMODE Masks */ + +#define RE 0x00000001 /* Receiver Enable */ +#define ASTP 0x00000002 /* Enable Automatic Pad Stripping On RX Frames */ +#define HU 0x00000010 /* Hash Filter Unicast Address */ +#define HM 0x00000020 /* Hash Filter Multicast Address */ +#define PAM 0x00000040 /* Pass-All-Multicast Mode Enable */ +#define PR 0x00000080 /* Promiscuous Mode Enable */ +#define IFE 0x00000100 /* Inverse Filtering Enable */ +#define DBF 0x00000200 /* Disable Broadcast Frame Reception */ +#define PBF 0x00000400 /* Pass Bad Frames Enable */ +#define PSF 0x00000800 /* Pass Short Frames Enable */ +#define RAF 0x00001000 /* Receive-All Mode */ +#define TE 0x00010000 /* Transmitter Enable */ +#define DTXPAD 0x00020000 /* Disable Automatic TX Padding */ +#define DTXCRC 0x00040000 /* Disable Automatic TX CRC Generation */ +#define DC 0x00080000 /* Deferral Check */ +#define BOLMT 0x00300000 /* Back-Off Limit */ +#define BOLMT_10 0x00000000 /* 10-bit range */ +#define BOLMT_8 0x00100000 /* 8-bit range */ +#define BOLMT_4 0x00200000 /* 4-bit range */ +#define BOLMT_1 0x00300000 /* 1-bit range */ +#define DRTY 0x00400000 /* Disable TX Retry On Collision */ +#define LCTRE 0x00800000 /* Enable TX Retry On Late Collision */ +#define RMII 0x01000000 /* RMII/MII* Mode */ +#define RMII_10 0x02000000 /* Speed Select for RMII Port (10MBit/100MBit*) */ +#define FDMODE 0x04000000 /* Duplex Mode Enable (Full/Half*) */ +#define LB 0x08000000 /* Internal Loopback Enable */ +#define DRO 0x10000000 /* Disable Receive Own Frames (Half-Duplex Mode) */ + +/* EMAC_STAADD Masks */ + +#define STABUSY 0x00000001 /* Initiate Station Mgt Reg Access / STA Busy Stat */ +#define STAOP 0x00000002 /* Station Management Operation Code (Write/Read*) */ +#define STADISPRE 0x00000004 /* Disable Preamble Generation */ +#define STAIE 0x00000008 /* Station Mgt. Transfer Done Interrupt Enable */ +#define REGAD 0x000007C0 /* STA Register Address */ +#define PHYAD 0x0000F800 /* PHY Device Address */ + +#define SET_REGAD(x) (((x)&0x1F)<< 6 ) /* Set STA Register Address */ +#define SET_PHYAD(x) (((x)&0x1F)<< 11 ) /* Set PHY Device Address */ + +/* EMAC_STADAT Mask */ + +#define STADATA 0x0000FFFF /* Station Management Data */ + +/* EMAC_FLC Masks */ + +#define FLCBUSY 0x00000001 /* Send Flow Ctrl Frame / Flow Ctrl Busy Status */ +#define FLCE 0x00000002 /* Flow Control Enable */ +#define PCF 0x00000004 /* Pass Control Frames */ +#define BKPRSEN 0x00000008 /* Enable Backpressure */ +#define FLCPAUSE 0xFFFF0000 /* Pause Time */ + +#define SET_FLCPAUSE(x) (((x)&0xFFFF)<< 16) /* Set Pause Time */ + +/* EMAC_WKUP_CTL Masks */ + +#define CAPWKFRM 0x00000001 /* Capture Wake-Up Frames */ +#define MPKE 0x00000002 /* Magic Packet Enable */ +#define RWKE 0x00000004 /* Remote Wake-Up Frame Enable */ +#define GUWKE 0x00000008 /* Global Unicast Wake Enable */ +#define MPKS 0x00000020 /* Magic Packet Received Status */ +#define RWKS 0x00000F00 /* Wake-Up Frame Received Status, Filters 3:0 */ + +/* EMAC_WKUP_FFCMD Masks */ + +#define WF0_E 0x00000001 /* Enable Wake-Up Filter 0 */ +#define WF0_T 0x00000008 /* Wake-Up Filter 0 Addr Type (Multicast/Unicast*) */ +#define WF1_E 0x00000100 /* Enable Wake-Up Filter 1 */ +#define WF1_T 0x00000800 /* Wake-Up Filter 1 Addr Type (Multicast/Unicast*) */ +#define WF2_E 0x00010000 /* Enable Wake-Up Filter 2 */ +#define WF2_T 0x00080000 /* Wake-Up Filter 2 Addr Type (Multicast/Unicast*) */ +#define WF3_E 0x01000000 /* Enable Wake-Up Filter 3 */ +#define WF3_T 0x08000000 /* Wake-Up Filter 3 Addr Type (Multicast/Unicast*) */ + +/* EMAC_WKUP_FFOFF Masks */ + +#define WF0_OFF 0x000000FF /* Wake-Up Filter 0 Pattern Offset */ +#define WF1_OFF 0x0000FF00 /* Wake-Up Filter 1 Pattern Offset */ +#define WF2_OFF 0x00FF0000 /* Wake-Up Filter 2 Pattern Offset */ +#define WF3_OFF 0xFF000000 /* Wake-Up Filter 3 Pattern Offset */ + +#define SET_WF0_OFF(x) (((x)&0xFF)<< 0 ) /* Set Wake-Up Filter 0 Byte Offset */ +#define SET_WF1_OFF(x) (((x)&0xFF)<< 8 ) /* Set Wake-Up Filter 1 Byte Offset */ +#define SET_WF2_OFF(x) (((x)&0xFF)<< 16 ) /* Set Wake-Up Filter 2 Byte Offset */ +#define SET_WF3_OFF(x) (((x)&0xFF)<< 24 ) /* Set Wake-Up Filter 3 Byte Offset */ +/* Set ALL Offsets */ +#define SET_WF_OFFS(x0,x1,x2,x3) (SET_WF0_OFF((x0))|SET_WF1_OFF((x1))|SET_WF2_OFF((x2))|SET_WF3_OFF((x3))) + +/* EMAC_WKUP_FFCRC0 Masks */ + +#define WF0_CRC 0x0000FFFF /* Wake-Up Filter 0 Pattern CRC */ +#define WF1_CRC 0xFFFF0000 /* Wake-Up Filter 1 Pattern CRC */ + +#define SET_WF0_CRC(x) (((x)&0xFFFF)<< 0 ) /* Set Wake-Up Filter 0 Target CRC */ +#define SET_WF1_CRC(x) (((x)&0xFFFF)<< 16 ) /* Set Wake-Up Filter 1 Target CRC */ + +/* EMAC_WKUP_FFCRC1 Masks */ + +#define WF2_CRC 0x0000FFFF /* Wake-Up Filter 2 Pattern CRC */ +#define WF3_CRC 0xFFFF0000 /* Wake-Up Filter 3 Pattern CRC */ + +#define SET_WF2_CRC(x) (((x)&0xFFFF)<< 0 ) /* Set Wake-Up Filter 2 Target CRC */ +#define SET_WF3_CRC(x) (((x)&0xFFFF)<< 16 ) /* Set Wake-Up Filter 3 Target CRC */ + +/* EMAC_SYSCTL Masks */ + +#define PHYIE 0x00000001 /* PHY_INT Interrupt Enable */ +#define RXDWA 0x00000002 /* Receive Frame DMA Word Alignment (Odd/Even*) */ +#define RXCKS 0x00000004 /* Enable RX Frame TCP/UDP Checksum Computation */ +#define TXDWA 0x00000010 /* Transmit Frame DMA Word Alignment (Odd/Even*) */ +#define MDCDIV 0x00003F00 /* SCLK:MDC Clock Divisor [MDC=SCLK/(2*(N+1))] */ + +#define SET_MDCDIV(x) (((x)&0x3F)<< 8) /* Set MDC Clock Divisor */ + +/* EMAC_SYSTAT Masks */ + +#define PHYINT 0x00000001 /* PHY_INT Interrupt Status */ +#define MMCINT 0x00000002 /* MMC Counter Interrupt Status */ +#define RXFSINT 0x00000004 /* RX Frame-Status Interrupt Status */ +#define TXFSINT 0x00000008 /* TX Frame-Status Interrupt Status */ +#define WAKEDET 0x00000010 /* Wake-Up Detected Status */ +#define RXDMAERR 0x00000020 /* RX DMA Direction Error Status */ +#define TXDMAERR 0x00000040 /* TX DMA Direction Error Status */ +#define STMDONE 0x00000080 /* Station Mgt. Transfer Done Interrupt Status */ + +/* EMAC_RX_STAT, EMAC_RX_STKY, and EMAC_RX_IRQE Masks */ + +#define RX_FRLEN 0x000007FF /* Frame Length In Bytes */ +#define RX_COMP 0x00001000 /* RX Frame Complete */ +#define RX_OK 0x00002000 /* RX Frame Received With No Errors */ +#define RX_LONG 0x00004000 /* RX Frame Too Long Error */ +#define RX_ALIGN 0x00008000 /* RX Frame Alignment Error */ +#define RX_CRC 0x00010000 /* RX Frame CRC Error */ +#define RX_LEN 0x00020000 /* RX Frame Length Error */ +#define RX_FRAG 0x00040000 /* RX Frame Fragment Error */ +#define RX_ADDR 0x00080000 /* RX Frame Address Filter Failed Error */ +#define RX_DMAO 0x00100000 /* RX Frame DMA Overrun Error */ +#define RX_PHY 0x00200000 /* RX Frame PHY Error */ +#define RX_LATE 0x00400000 /* RX Frame Late Collision Error */ +#define RX_RANGE 0x00800000 /* RX Frame Length Field Out of Range Error */ +#define RX_MULTI 0x01000000 /* RX Multicast Frame Indicator */ +#define RX_BROAD 0x02000000 /* RX Broadcast Frame Indicator */ +#define RX_CTL 0x04000000 /* RX Control Frame Indicator */ +#define RX_UCTL 0x08000000 /* Unsupported RX Control Frame Indicator */ +#define RX_TYPE 0x10000000 /* RX Typed Frame Indicator */ +#define RX_VLAN1 0x20000000 /* RX VLAN1 Frame Indicator */ +#define RX_VLAN2 0x40000000 /* RX VLAN2 Frame Indicator */ +#define RX_ACCEPT 0x80000000 /* RX Frame Accepted Indicator */ + +/* EMAC_TX_STAT, EMAC_TX_STKY, and EMAC_TX_IRQE Masks */ + +#define TX_COMP 0x00000001 /* TX Frame Complete */ +#define TX_OK 0x00000002 /* TX Frame Sent With No Errors */ +#define TX_ECOLL 0x00000004 /* TX Frame Excessive Collision Error */ +#define TX_LATE 0x00000008 /* TX Frame Late Collision Error */ +#define TX_DMAU 0x00000010 /* TX Frame DMA Underrun Error (STAT) */ +#define TX_MACE 0x00000010 /* Internal MAC Error Detected (STKY and IRQE) */ +#define TX_EDEFER 0x00000020 /* TX Frame Excessive Deferral Error */ +#define TX_BROAD 0x00000040 /* TX Broadcast Frame Indicator */ +#define TX_MULTI 0x00000080 /* TX Multicast Frame Indicator */ +#define TX_CCNT 0x00000F00 /* TX Frame Collision Count */ +#define TX_DEFER 0x00001000 /* TX Frame Deferred Indicator */ +#define TX_CRS 0x00002000 /* TX Frame Carrier Sense Not Asserted Error */ +#define TX_LOSS 0x00004000 /* TX Frame Carrier Lost During TX Error */ +#define TX_RETRY 0x00008000 /* TX Frame Successful After Retry */ +#define TX_FRLEN 0x07FF0000 /* TX Frame Length (Bytes) */ + +/* EMAC_MMC_CTL Masks */ +#define RSTC 0x00000001 /* Reset All Counters */ +#define CROLL 0x00000002 /* Counter Roll-Over Enable */ +#define CCOR 0x00000004 /* Counter Clear-On-Read Mode Enable */ +#define MMCE 0x00000008 /* Enable MMC Counter Operation */ + +/* EMAC_MMC_RIRQS and EMAC_MMC_RIRQE Masks */ +#define RX_OK_CNT 0x00000001 /* RX Frames Received With No Errors */ +#define RX_FCS_CNT 0x00000002 /* RX Frames W/Frame Check Sequence Errors */ +#define RX_ALIGN_CNT 0x00000004 /* RX Frames With Alignment Errors */ +#define RX_OCTET_CNT 0x00000008 /* RX Octets Received OK */ +#define RX_LOST_CNT 0x00000010 /* RX Frames Lost Due To Internal MAC RX Error */ +#define RX_UNI_CNT 0x00000020 /* Unicast RX Frames Received OK */ +#define RX_MULTI_CNT 0x00000040 /* Multicast RX Frames Received OK */ +#define RX_BROAD_CNT 0x00000080 /* Broadcast RX Frames Received OK */ +#define RX_IRL_CNT 0x00000100 /* RX Frames With In-Range Length Errors */ +#define RX_ORL_CNT 0x00000200 /* RX Frames With Out-Of-Range Length Errors */ +#define RX_LONG_CNT 0x00000400 /* RX Frames With Frame Too Long Errors */ +#define RX_MACCTL_CNT 0x00000800 /* MAC Control RX Frames Received */ +#define RX_OPCODE_CTL 0x00001000 /* Unsupported Op-Code RX Frames Received */ +#define RX_PAUSE_CNT 0x00002000 /* PAUSEMAC Control RX Frames Received */ +#define RX_ALLF_CNT 0x00004000 /* All RX Frames Received */ +#define RX_ALLO_CNT 0x00008000 /* All RX Octets Received */ +#define RX_TYPED_CNT 0x00010000 /* Typed RX Frames Received */ +#define RX_SHORT_CNT 0x00020000 /* RX Frame Fragments (< 64 Bytes) Received */ +#define RX_EQ64_CNT 0x00040000 /* 64-Byte RX Frames Received */ +#define RX_LT128_CNT 0x00080000 /* 65-127-Byte RX Frames Received */ +#define RX_LT256_CNT 0x00100000 /* 128-255-Byte RX Frames Received */ +#define RX_LT512_CNT 0x00200000 /* 256-511-Byte RX Frames Received */ +#define RX_LT1024_CNT 0x00400000 /* 512-1023-Byte RX Frames Received */ +#define RX_GE1024_CNT 0x00800000 /* 1024-Max-Byte RX Frames Received */ + +/* EMAC_MMC_TIRQS and EMAC_MMC_TIRQE Masks */ + +#define TX_OK_CNT 0x00000001 /* TX Frames Sent OK */ +#define TX_SCOLL_CNT 0x00000002 /* TX Frames With Single Collisions */ +#define TX_MCOLL_CNT 0x00000004 /* TX Frames With Multiple Collisions */ +#define TX_OCTET_CNT 0x00000008 /* TX Octets Sent OK */ +#define TX_DEFER_CNT 0x00000010 /* TX Frames With Deferred Transmission */ +#define TX_LATE_CNT 0x00000020 /* TX Frames With Late Collisions */ +#define TX_ABORTC_CNT 0x00000040 /* TX Frames Aborted Due To Excess Collisions */ +#define TX_LOST_CNT 0x00000080 /* TX Frames Lost Due To Internal MAC TX Error */ +#define TX_CRS_CNT 0x00000100 /* TX Frames With Carrier Sense Errors */ +#define TX_UNI_CNT 0x00000200 /* Unicast TX Frames Sent */ +#define TX_MULTI_CNT 0x00000400 /* Multicast TX Frames Sent */ +#define TX_BROAD_CNT 0x00000800 /* Broadcast TX Frames Sent */ +#define TX_EXDEF_CTL 0x00001000 /* TX Frames With Excessive Deferral */ +#define TX_MACCTL_CNT 0x00002000 /* MAC Control TX Frames Sent */ +#define TX_ALLF_CNT 0x00004000 /* All TX Frames Sent */ +#define TX_ALLO_CNT 0x00008000 /* All TX Octets Sent */ +#define TX_EQ64_CNT 0x00010000 /* 64-Byte TX Frames Sent */ +#define TX_LT128_CNT 0x00020000 /* 65-127-Byte TX Frames Sent */ +#define TX_LT256_CNT 0x00040000 /* 128-255-Byte TX Frames Sent */ +#define TX_LT512_CNT 0x00080000 /* 256-511-Byte TX Frames Sent */ +#define TX_LT1024_CNT 0x00100000 /* 512-1023-Byte TX Frames Sent */ +#define TX_GE1024_CNT 0x00200000 /* 1024-Max-Byte TX Frames Sent */ +#define TX_ABORT_CNT 0x00400000 /* TX Frames Aborted */ + +/* SDH Registers */ + +#define SDH_PWR_CTL 0xFFC03900 /* SDH Power Control */ +#define SDH_CLK_CTL 0xFFC03904 /* SDH Clock Control */ +#define SDH_ARGUMENT 0xFFC03908 /* SDH Argument */ +#define SDH_COMMAND 0xFFC0390C /* SDH Command */ +#define SDH_RESP_CMD 0xFFC03910 /* SDH Response Command */ +#define SDH_RESPONSE0 0xFFC03914 /* SDH Response0 */ +#define SDH_RESPONSE1 0xFFC03918 /* SDH Response1 */ +#define SDH_RESPONSE2 0xFFC0391C /* SDH Response2 */ +#define SDH_RESPONSE3 0xFFC03920 /* SDH Response3 */ +#define SDH_DATA_TIMER 0xFFC03924 /* SDH Data Timer */ +#define SDH_DATA_LGTH 0xFFC03928 /* SDH Data Length */ +#define SDH_DATA_CTL 0xFFC0392C /* SDH Data Control */ +#define SDH_DATA_CNT 0xFFC03930 /* SDH Data Counter */ +#define SDH_STATUS 0xFFC03934 /* SDH Status */ +#define SDH_STATUS_CLR 0xFFC03938 /* SDH Status Clear */ +#define SDH_MASK0 0xFFC0393C /* SDH Interrupt0 Mask */ +#define SDH_MASK1 0xFFC03940 /* SDH Interrupt1 Mask */ +#define SDH_FIFO_CNT 0xFFC03948 /* SDH FIFO Counter */ +#define SDH_FIFO 0xFFC03980 /* SDH Data FIFO */ +#define SDH_E_STATUS 0xFFC039C0 /* SDH Exception Status */ +#define SDH_E_MASK 0xFFC039C4 /* SDH Exception Mask */ +#define SDH_CFG 0xFFC039C8 /* SDH Configuration */ +#define SDH_RD_WAIT_EN 0xFFC039CC /* SDH Read Wait Enable */ +#define SDH_PID0 0xFFC039D0 /* SDH Peripheral Identification0 */ +#define SDH_PID1 0xFFC039D4 /* SDH Peripheral Identification1 */ +#define SDH_PID2 0xFFC039D8 /* SDH Peripheral Identification2 */ +#define SDH_PID3 0xFFC039DC /* SDH Peripheral Identification3 */ +#define SDH_PID4 0xFFC039E0 /* SDH Peripheral Identification4 */ +#define SDH_PID5 0xFFC039E4 /* SDH Peripheral Identification5 */ +#define SDH_PID6 0xFFC039E8 /* SDH Peripheral Identification6 */ +#define SDH_PID7 0xFFC039EC /* SDH Peripheral Identification7 */ + +/* Removable Storage Interface Registers */ + +#define RSI_PWR_CONTROL 0xFFC03800 /* RSI Power Control Register */ +#define RSI_CLK_CONTROL 0xFFC03804 /* RSI Clock Control Register */ +#define RSI_ARGUMENT 0xFFC03808 /* RSI Argument Register */ +#define RSI_COMMAND 0xFFC0380C /* RSI Command Register */ +#define RSI_RESP_CMD 0xFFC03810 /* RSI Response Command Register */ +#define RSI_RESPONSE0 0xFFC03814 /* RSI Response Register */ +#define RSI_RESPONSE1 0xFFC03818 /* RSI Response Register */ +#define RSI_RESPONSE2 0xFFC0381C /* RSI Response Register */ +#define RSI_RESPONSE3 0xFFC03820 /* RSI Response Register */ +#define RSI_DATA_TIMER 0xFFC03824 /* RSI Data Timer Register */ +#define RSI_DATA_LGTH 0xFFC03828 /* RSI Data Length Register */ +#define RSI_DATA_CONTROL 0xFFC0382C /* RSI Data Control Register */ +#define RSI_DATA_CNT 0xFFC03830 /* RSI Data Counter Register */ +#define RSI_STATUS 0xFFC03834 /* RSI Status Register */ +#define RSI_STATUSCL 0xFFC03838 /* RSI Status Clear Register */ +#define RSI_MASK0 0xFFC0383C /* RSI Interrupt 0 Mask Register */ +#define RSI_MASK1 0xFFC03840 /* RSI Interrupt 1 Mask Register */ +#define RSI_FIFO_CNT 0xFFC03848 /* RSI FIFO Counter Register */ +#define RSI_CEATA_CONTROL 0xFFC0384C /* RSI CEATA Register */ +#define RSI_FIFO 0xFFC03880 /* RSI Data FIFO Register */ +#define RSI_ESTAT 0xFFC038C0 /* RSI Exception Status Register */ +#define RSI_EMASK 0xFFC038C4 /* RSI Exception Mask Register */ +#define RSI_CONFIG 0xFFC038C8 /* RSI Configuration Register */ +#define RSI_RD_WAIT_EN 0xFFC038CC /* RSI Read Wait Enable Register */ +#define RSI_PID0 0xFFC03FE0 /* RSI Peripheral ID Register 0 */ +#define RSI_PID1 0xFFC03FE4 /* RSI Peripheral ID Register 1 */ +#define RSI_PID2 0xFFC03FE8 /* RSI Peripheral ID Register 2 */ +#define RSI_PID3 0xFFC03FEC /* RSI Peripheral ID Register 3 */ +#define RSI_PID4 0xFFC03FF0 /* RSI Peripheral ID Register 4 */ +#define RSI_PID5 0xFFC03FF4 /* RSI Peripheral ID Register 5 */ +#define RSI_PID6 0xFFC03FF8 /* RSI Peripheral ID Register 6 */ +#define RSI_PID7 0xFFC03FFC /* RSI Peripheral ID Register 7 */ + +/* PTP TSYNC Registers */ + +#define EMAC_PTP_CTL 0xFFC030A0 /* PTP Block Control */ +#define EMAC_PTP_IE 0xFFC030A4 /* PTP Block Interrupt Enable */ +#define EMAC_PTP_ISTAT 0xFFC030A8 /* PTP Block Interrupt Status */ +#define EMAC_PTP_FOFF 0xFFC030AC /* PTP Filter offset Register */ +#define EMAC_PTP_FV1 0xFFC030B0 /* PTP Filter Value Register 1 */ +#define EMAC_PTP_FV2 0xFFC030B4 /* PTP Filter Value Register 2 */ +#define EMAC_PTP_FV3 0xFFC030B8 /* PTP Filter Value Register 3 */ +#define EMAC_PTP_ADDEND 0xFFC030BC /* PTP Addend for Frequency Compensation */ +#define EMAC_PTP_ACCR 0xFFC030C0 /* PTP Accumulator for Frequency Compensation */ +#define EMAC_PTP_OFFSET 0xFFC030C4 /* PTP Time Offset Register */ +#define EMAC_PTP_TIMELO 0xFFC030C8 /* PTP Precision Clock Time Low */ +#define EMAC_PTP_TIMEHI 0xFFC030CC /* PTP Precision Clock Time High */ +#define EMAC_PTP_RXSNAPLO 0xFFC030D0 /* PTP Receive Snapshot Register Low */ +#define EMAC_PTP_RXSNAPHI 0xFFC030D4 /* PTP Receive Snapshot Register High */ +#define EMAC_PTP_TXSNAPLO 0xFFC030D8 /* PTP Transmit Snapshot Register Low */ +#define EMAC_PTP_TXSNAPHI 0xFFC030DC /* PTP Transmit Snapshot Register High */ +#define EMAC_PTP_ALARMLO 0xFFC030E0 /* PTP Alarm time Low */ +#define EMAC_PTP_ALARMHI 0xFFC030E4 /* PTP Alarm time High */ +#define EMAC_PTP_ID_OFF 0xFFC030E8 /* PTP Capture ID offset register */ +#define EMAC_PTP_ID_SNAP 0xFFC030EC /* PTP Capture ID register */ +#define EMAC_PTP_PPS_STARTLO 0xFFC030F0 /* PPS Start Time Low */ +#define EMAC_PTP_PPS_STARTHI 0xFFC030F4 /* PPS Start Time High */ +#define EMAC_PTP_PPS_PERIOD 0xFFC030F8 /* PPS Count Register */ + +#endif /* _DEF_BF518_H */ diff --git a/arch/blackfin/mach-bf518/include/mach/defBF51x_base.h b/arch/blackfin/mach-bf518/include/mach/defBF51x_base.h new file mode 100644 index 00000000000..1bec8d1c2a7 --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/defBF51x_base.h @@ -0,0 +1,1940 @@ +/* + * File: include/asm-blackfin/mach-bf518/defBF51x_base.h + * Based on: + * Author: + * + * Created: + * Description: + * + * Rev: + * + * Modified: + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _DEF_BF51X_H +#define _DEF_BF51X_H + + +/* ************************************************************** */ +/* SYSTEM & MMR ADDRESS DEFINITIONS COMMON TO ALL ADSP-BF51x */ +/* ************************************************************** */ + +/* Clock and System Control (0xFFC00000 - 0xFFC000FF) */ +#define PLL_CTL 0xFFC00000 /* PLL Control Register */ +#define PLL_DIV 0xFFC00004 /* PLL Divide Register */ +#define VR_CTL 0xFFC00008 /* Voltage Regulator Control Register */ +#define PLL_STAT 0xFFC0000C /* PLL Status Register */ +#define PLL_LOCKCNT 0xFFC00010 /* PLL Lock Count Register */ +#define CHIPID 0xFFC00014 /* Device ID Register */ + +/* System Interrupt Controller (0xFFC00100 - 0xFFC001FF) */ +#define SWRST 0xFFC00100 /* Software Reset Register */ +#define SYSCR 0xFFC00104 /* System Configuration Register */ +#define SIC_RVECT 0xFFC00108 /* Interrupt Reset Vector Address Register */ + +#define SIC_IMASK0 0xFFC0010C /* Interrupt Mask Register */ +#define SIC_IAR0 0xFFC00110 /* Interrupt Assignment Register 0 */ +#define SIC_IAR1 0xFFC00114 /* Interrupt Assignment Register 1 */ +#define SIC_IAR2 0xFFC00118 /* Interrupt Assignment Register 2 */ +#define SIC_IAR3 0xFFC0011C /* Interrupt Assignment Register 3 */ +#define SIC_ISR0 0xFFC00120 /* Interrupt Status Register */ +#define SIC_IWR0 0xFFC00124 /* Interrupt Wakeup Register */ + +/* SIC Additions to ADSP-BF51x (0xFFC0014C - 0xFFC00162) */ +#define SIC_IMASK1 0xFFC0014C /* Interrupt Mask register of SIC2 */ +#define SIC_IAR4 0xFFC00150 /* Interrupt Assignment register4 */ +#define SIC_IAR5 0xFFC00154 /* Interrupt Assignment register5 */ +#define SIC_IAR6 0xFFC00158 /* Interrupt Assignment register6 */ +#define SIC_IAR7 0xFFC0015C /* Interrupt Assignment register7 */ +#define SIC_ISR1 0xFFC00160 /* Interrupt Statur register */ +#define SIC_IWR1 0xFFC00164 /* Interrupt Wakeup register */ + + +/* Watchdog Timer (0xFFC00200 - 0xFFC002FF) */ +#define WDOG_CTL 0xFFC00200 /* Watchdog Control Register */ +#define WDOG_CNT 0xFFC00204 /* Watchdog Count Register */ +#define WDOG_STAT 0xFFC00208 /* Watchdog Status Register */ + + +/* Real Time Clock (0xFFC00300 - 0xFFC003FF) */ +#define RTC_STAT 0xFFC00300 /* RTC Status Register */ +#define RTC_ICTL 0xFFC00304 /* RTC Interrupt Control Register */ +#define RTC_ISTAT 0xFFC00308 /* RTC Interrupt Status Register */ +#define RTC_SWCNT 0xFFC0030C /* RTC Stopwatch Count Register */ +#define RTC_ALARM 0xFFC00310 /* RTC Alarm Time Register */ +#define RTC_FAST 0xFFC00314 /* RTC Prescaler Enable Register */ +#define RTC_PREN 0xFFC00314 /* RTC Prescaler Enable Alternate Macro */ + + +/* UART0 Controller (0xFFC00400 - 0xFFC004FF) */ +#define UART0_THR 0xFFC00400 /* Transmit Holding register */ +#define UART0_RBR 0xFFC00400 /* Receive Buffer register */ +#define UART0_DLL 0xFFC00400 /* Divisor Latch (Low-Byte) */ +#define UART0_IER 0xFFC00404 /* Interrupt Enable Register */ +#define UART0_DLH 0xFFC00404 /* Divisor Latch (High-Byte) */ +#define UART0_IIR 0xFFC00408 /* Interrupt Identification Register */ +#define UART0_LCR 0xFFC0040C /* Line Control Register */ +#define UART0_MCR 0xFFC00410 /* Modem Control Register */ +#define UART0_LSR 0xFFC00414 /* Line Status Register */ +#define UART0_MSR 0xFFC00418 /* Modem Status Register */ +#define UART0_SCR 0xFFC0041C /* SCR Scratch Register */ +#define UART0_GCTL 0xFFC00424 /* Global Control Register */ + +/* SPI0 Controller (0xFFC00500 - 0xFFC005FF) */ +#define SPI0_REGBASE 0xFFC00500 +#define SPI0_CTL 0xFFC00500 /* SPI Control Register */ +#define SPI0_FLG 0xFFC00504 /* SPI Flag register */ +#define SPI0_STAT 0xFFC00508 /* SPI Status register */ +#define SPI0_TDBR 0xFFC0050C /* SPI Transmit Data Buffer Register */ +#define SPI0_RDBR 0xFFC00510 /* SPI Receive Data Buffer Register */ +#define SPI0_BAUD 0xFFC00514 /* SPI Baud rate Register */ +#define SPI0_SHADOW 0xFFC00518 /* SPI_RDBR Shadow Register */ + +/* SPI1 Controller (0xFFC03400 - 0xFFC034FF) */ +#define SPI1_REGBASE 0xFFC03400 +#define SPI1_CTL 0xFFC03400 /* SPI Control Register */ +#define SPI1_FLG 0xFFC03404 /* SPI Flag register */ +#define SPI1_STAT 0xFFC03408 /* SPI Status register */ +#define SPI1_TDBR 0xFFC0340C /* SPI Transmit Data Buffer Register */ +#define SPI1_RDBR 0xFFC03410 /* SPI Receive Data Buffer Register */ +#define SPI1_BAUD 0xFFC03414 /* SPI Baud rate Register */ +#define SPI1_SHADOW 0xFFC03418 /* SPI_RDBR Shadow Register */ + +/* TIMER0-7 Registers (0xFFC00600 - 0xFFC006FF) */ +#define TIMER0_CONFIG 0xFFC00600 /* Timer 0 Configuration Register */ +#define TIMER0_COUNTER 0xFFC00604 /* Timer 0 Counter Register */ +#define TIMER0_PERIOD 0xFFC00608 /* Timer 0 Period Register */ +#define TIMER0_WIDTH 0xFFC0060C /* Timer 0 Width Register */ + +#define TIMER1_CONFIG 0xFFC00610 /* Timer 1 Configuration Register */ +#define TIMER1_COUNTER 0xFFC00614 /* Timer 1 Counter Register */ +#define TIMER1_PERIOD 0xFFC00618 /* Timer 1 Period Register */ +#define TIMER1_WIDTH 0xFFC0061C /* Timer 1 Width Register */ + +#define TIMER2_CONFIG 0xFFC00620 /* Timer 2 Configuration Register */ +#define TIMER2_COUNTER 0xFFC00624 /* Timer 2 Counter Register */ +#define TIMER2_PERIOD 0xFFC00628 /* Timer 2 Period Register */ +#define TIMER2_WIDTH 0xFFC0062C /* Timer 2 Width Register */ + +#define TIMER3_CONFIG 0xFFC00630 /* Timer 3 Configuration Register */ +#define TIMER3_COUNTER 0xFFC00634 /* Timer 3 Counter Register */ +#define TIMER3_PERIOD 0xFFC00638 /* Timer 3 Period Register */ +#define TIMER3_WIDTH 0xFFC0063C /* Timer 3 Width Register */ + +#define TIMER4_CONFIG 0xFFC00640 /* Timer 4 Configuration Register */ +#define TIMER4_COUNTER 0xFFC00644 /* Timer 4 Counter Register */ +#define TIMER4_PERIOD 0xFFC00648 /* Timer 4 Period Register */ +#define TIMER4_WIDTH 0xFFC0064C /* Timer 4 Width Register */ + +#define TIMER5_CONFIG 0xFFC00650 /* Timer 5 Configuration Register */ +#define TIMER5_COUNTER 0xFFC00654 /* Timer 5 Counter Register */ +#define TIMER5_PERIOD 0xFFC00658 /* Timer 5 Period Register */ +#define TIMER5_WIDTH 0xFFC0065C /* Timer 5 Width Register */ + +#define TIMER6_CONFIG 0xFFC00660 /* Timer 6 Configuration Register */ +#define TIMER6_COUNTER 0xFFC00664 /* Timer 6 Counter Register */ +#define TIMER6_PERIOD 0xFFC00668 /* Timer 6 Period Register */ +#define TIMER6_WIDTH 0xFFC0066C /* Timer 6 Width Register */ + +#define TIMER7_CONFIG 0xFFC00670 /* Timer 7 Configuration Register */ +#define TIMER7_COUNTER 0xFFC00674 /* Timer 7 Counter Register */ +#define TIMER7_PERIOD 0xFFC00678 /* Timer 7 Period Register */ +#define TIMER7_WIDTH 0xFFC0067C /* Timer 7 Width Register */ + +#define TIMER_ENABLE 0xFFC00680 /* Timer Enable Register */ +#define TIMER_DISABLE 0xFFC00684 /* Timer Disable Register */ +#define TIMER_STATUS 0xFFC00688 /* Timer Status Register */ + +/* General Purpose I/O Port F (0xFFC00700 - 0xFFC007FF) */ +#define PORTFIO 0xFFC00700 /* Port F I/O Pin State Specify Register */ +#define PORTFIO_CLEAR 0xFFC00704 /* Port F I/O Peripheral Interrupt Clear Register */ +#define PORTFIO_SET 0xFFC00708 /* Port F I/O Peripheral Interrupt Set Register */ +#define PORTFIO_TOGGLE 0xFFC0070C /* Port F I/O Pin State Toggle Register */ +#define PORTFIO_MASKA 0xFFC00710 /* Port F I/O Mask State Specify Interrupt A Register */ +#define PORTFIO_MASKA_CLEAR 0xFFC00714 /* Port F I/O Mask Disable Interrupt A Register */ +#define PORTFIO_MASKA_SET 0xFFC00718 /* Port F I/O Mask Enable Interrupt A Register */ +#define PORTFIO_MASKA_TOGGLE 0xFFC0071C /* Port F I/O Mask Toggle Enable Interrupt A Register */ +#define PORTFIO_MASKB 0xFFC00720 /* Port F I/O Mask State Specify Interrupt B Register */ +#define PORTFIO_MASKB_CLEAR 0xFFC00724 /* Port F I/O Mask Disable Interrupt B Register */ +#define PORTFIO_MASKB_SET 0xFFC00728 /* Port F I/O Mask Enable Interrupt B Register */ +#define PORTFIO_MASKB_TOGGLE 0xFFC0072C /* Port F I/O Mask Toggle Enable Interrupt B Register */ +#define PORTFIO_DIR 0xFFC00730 /* Port F I/O Direction Register */ +#define PORTFIO_POLAR 0xFFC00734 /* Port F I/O Source Polarity Register */ +#define PORTFIO_EDGE 0xFFC00738 /* Port F I/O Source Sensitivity Register */ +#define PORTFIO_BOTH 0xFFC0073C /* Port F I/O Set on BOTH Edges Register */ +#define PORTFIO_INEN 0xFFC00740 /* Port F I/O Input Enable Register */ + +/* SPORT0 Controller (0xFFC00800 - 0xFFC008FF) */ +#define SPORT0_TCR1 0xFFC00800 /* SPORT0 Transmit Configuration 1 Register */ +#define SPORT0_TCR2 0xFFC00804 /* SPORT0 Transmit Configuration 2 Register */ +#define SPORT0_TCLKDIV 0xFFC00808 /* SPORT0 Transmit Clock Divider */ +#define SPORT0_TFSDIV 0xFFC0080C /* SPORT0 Transmit Frame Sync Divider */ +#define SPORT0_TX 0xFFC00810 /* SPORT0 TX Data Register */ +#define SPORT0_RX 0xFFC00818 /* SPORT0 RX Data Register */ +#define SPORT0_RCR1 0xFFC00820 /* SPORT0 Transmit Configuration 1 Register */ +#define SPORT0_RCR2 0xFFC00824 /* SPORT0 Transmit Configuration 2 Register */ +#define SPORT0_RCLKDIV 0xFFC00828 /* SPORT0 Receive Clock Divider */ +#define SPORT0_RFSDIV 0xFFC0082C /* SPORT0 Receive Frame Sync Divider */ +#define SPORT0_STAT 0xFFC00830 /* SPORT0 Status Register */ +#define SPORT0_CHNL 0xFFC00834 /* SPORT0 Current Channel Register */ +#define SPORT0_MCMC1 0xFFC00838 /* SPORT0 Multi-Channel Configuration Register 1 */ +#define SPORT0_MCMC2 0xFFC0083C /* SPORT0 Multi-Channel Configuration Register 2 */ +#define SPORT0_MTCS0 0xFFC00840 /* SPORT0 Multi-Channel Transmit Select Register 0 */ +#define SPORT0_MTCS1 0xFFC00844 /* SPORT0 Multi-Channel Transmit Select Register 1 */ +#define SPORT0_MTCS2 0xFFC00848 /* SPORT0 Multi-Channel Transmit Select Register 2 */ +#define SPORT0_MTCS3 0xFFC0084C /* SPORT0 Multi-Channel Transmit Select Register 3 */ +#define SPORT0_MRCS0 0xFFC00850 /* SPORT0 Multi-Channel Receive Select Register 0 */ +#define SPORT0_MRCS1 0xFFC00854 /* SPORT0 Multi-Channel Receive Select Register 1 */ +#define SPORT0_MRCS2 0xFFC00858 /* SPORT0 Multi-Channel Receive Select Register 2 */ +#define SPORT0_MRCS3 0xFFC0085C /* SPORT0 Multi-Channel Receive Select Register 3 */ + +/* SPORT1 Controller (0xFFC00900 - 0xFFC009FF) */ +#define SPORT1_TCR1 0xFFC00900 /* SPORT1 Transmit Configuration 1 Register */ +#define SPORT1_TCR2 0xFFC00904 /* SPORT1 Transmit Configuration 2 Register */ +#define SPORT1_TCLKDIV 0xFFC00908 /* SPORT1 Transmit Clock Divider */ +#define SPORT1_TFSDIV 0xFFC0090C /* SPORT1 Transmit Frame Sync Divider */ +#define SPORT1_TX 0xFFC00910 /* SPORT1 TX Data Register */ +#define SPORT1_RX 0xFFC00918 /* SPORT1 RX Data Register */ +#define SPORT1_RCR1 0xFFC00920 /* SPORT1 Transmit Configuration 1 Register */ +#define SPORT1_RCR2 0xFFC00924 /* SPORT1 Transmit Configuration 2 Register */ +#define SPORT1_RCLKDIV 0xFFC00928 /* SPORT1 Receive Clock Divider */ +#define SPORT1_RFSDIV 0xFFC0092C /* SPORT1 Receive Frame Sync Divider */ +#define SPORT1_STAT 0xFFC00930 /* SPORT1 Status Register */ +#define SPORT1_CHNL 0xFFC00934 /* SPORT1 Current Channel Register */ +#define SPORT1_MCMC1 0xFFC00938 /* SPORT1 Multi-Channel Configuration Register 1 */ +#define SPORT1_MCMC2 0xFFC0093C /* SPORT1 Multi-Channel Configuration Register 2 */ +#define SPORT1_MTCS0 0xFFC00940 /* SPORT1 Multi-Channel Transmit Select Register 0 */ +#define SPORT1_MTCS1 0xFFC00944 /* SPORT1 Multi-Channel Transmit Select Register 1 */ +#define SPORT1_MTCS2 0xFFC00948 /* SPORT1 Multi-Channel Transmit Select Register 2 */ +#define SPORT1_MTCS3 0xFFC0094C /* SPORT1 Multi-Channel Transmit Select Register 3 */ +#define SPORT1_MRCS0 0xFFC00950 /* SPORT1 Multi-Channel Receive Select Register 0 */ +#define SPORT1_MRCS1 0xFFC00954 /* SPORT1 Multi-Channel Receive Select Register 1 */ +#define SPORT1_MRCS2 0xFFC00958 /* SPORT1 Multi-Channel Receive Select Register 2 */ +#define SPORT1_MRCS3 0xFFC0095C /* SPORT1 Multi-Channel Receive Select Register 3 */ + +/* External Bus Interface Unit (0xFFC00A00 - 0xFFC00AFF) */ +#define EBIU_AMGCTL 0xFFC00A00 /* Asynchronous Memory Global Control Register */ +#define EBIU_AMBCTL0 0xFFC00A04 /* Asynchronous Memory Bank Control Register 0 */ +#define EBIU_AMBCTL1 0xFFC00A08 /* Asynchronous Memory Bank Control Register 1 */ +#define EBIU_SDGCTL 0xFFC00A10 /* SDRAM Global Control Register */ +#define EBIU_SDBCTL 0xFFC00A14 /* SDRAM Bank Control Register */ +#define EBIU_SDRRC 0xFFC00A18 /* SDRAM Refresh Rate Control Register */ +#define EBIU_SDSTAT 0xFFC00A1C /* SDRAM Status Register */ + +/* DMA Traffic Control Registers */ +#define DMA_TC_PER 0xFFC00B0C /* Traffic Control Periods Register */ +#define DMA_TC_CNT 0xFFC00B10 /* Traffic Control Current Counts Register */ + +/* Alternate deprecated register names (below) provided for backwards code compatibility */ +#define DMA_TCPER 0xFFC00B0C /* Traffic Control Periods Register */ +#define DMA_TCCNT 0xFFC00B10 /* Traffic Control Current Counts Register */ + +/* DMA Controller (0xFFC00C00 - 0xFFC00FFF) */ +#define DMA0_NEXT_DESC_PTR 0xFFC00C00 /* DMA Channel 0 Next Descriptor Pointer Register */ +#define DMA0_START_ADDR 0xFFC00C04 /* DMA Channel 0 Start Address Register */ +#define DMA0_CONFIG 0xFFC00C08 /* DMA Channel 0 Configuration Register */ +#define DMA0_X_COUNT 0xFFC00C10 /* DMA Channel 0 X Count Register */ +#define DMA0_X_MODIFY 0xFFC00C14 /* DMA Channel 0 X Modify Register */ +#define DMA0_Y_COUNT 0xFFC00C18 /* DMA Channel 0 Y Count Register */ +#define DMA0_Y_MODIFY 0xFFC00C1C /* DMA Channel 0 Y Modify Register */ +#define DMA0_CURR_DESC_PTR 0xFFC00C20 /* DMA Channel 0 Current Descriptor Pointer Register */ +#define DMA0_CURR_ADDR 0xFFC00C24 /* DMA Channel 0 Current Address Register */ +#define DMA0_IRQ_STATUS 0xFFC00C28 /* DMA Channel 0 Interrupt/Status Register */ +#define DMA0_PERIPHERAL_MAP 0xFFC00C2C /* DMA Channel 0 Peripheral Map Register */ +#define DMA0_CURR_X_COUNT 0xFFC00C30 /* DMA Channel 0 Current X Count Register */ +#define DMA0_CURR_Y_COUNT 0xFFC00C38 /* DMA Channel 0 Current Y Count Register */ + +#define DMA1_NEXT_DESC_PTR 0xFFC00C40 /* DMA Channel 1 Next Descriptor Pointer Register */ +#define DMA1_START_ADDR 0xFFC00C44 /* DMA Channel 1 Start Address Register */ +#define DMA1_CONFIG 0xFFC00C48 /* DMA Channel 1 Configuration Register */ +#define DMA1_X_COUNT 0xFFC00C50 /* DMA Channel 1 X Count Register */ +#define DMA1_X_MODIFY 0xFFC00C54 /* DMA Channel 1 X Modify Register */ +#define DMA1_Y_COUNT 0xFFC00C58 /* DMA Channel 1 Y Count Register */ +#define DMA1_Y_MODIFY 0xFFC00C5C /* DMA Channel 1 Y Modify Register */ +#define DMA1_CURR_DESC_PTR 0xFFC00C60 /* DMA Channel 1 Current Descriptor Pointer Register */ +#define DMA1_CURR_ADDR 0xFFC00C64 /* DMA Channel 1 Current Address Register */ +#define DMA1_IRQ_STATUS 0xFFC00C68 /* DMA Channel 1 Interrupt/Status Register */ +#define DMA1_PERIPHERAL_MAP 0xFFC00C6C /* DMA Channel 1 Peripheral Map Register */ +#define DMA1_CURR_X_COUNT 0xFFC00C70 /* DMA Channel 1 Current X Count Register */ +#define DMA1_CURR_Y_COUNT 0xFFC00C78 /* DMA Channel 1 Current Y Count Register */ + +#define DMA2_NEXT_DESC_PTR 0xFFC00C80 /* DMA Channel 2 Next Descriptor Pointer Register */ +#define DMA2_START_ADDR 0xFFC00C84 /* DMA Channel 2 Start Address Register */ +#define DMA2_CONFIG 0xFFC00C88 /* DMA Channel 2 Configuration Register */ +#define DMA2_X_COUNT 0xFFC00C90 /* DMA Channel 2 X Count Register */ +#define DMA2_X_MODIFY 0xFFC00C94 /* DMA Channel 2 X Modify Register */ +#define DMA2_Y_COUNT 0xFFC00C98 /* DMA Channel 2 Y Count Register */ +#define DMA2_Y_MODIFY 0xFFC00C9C /* DMA Channel 2 Y Modify Register */ +#define DMA2_CURR_DESC_PTR 0xFFC00CA0 /* DMA Channel 2 Current Descriptor Pointer Register */ +#define DMA2_CURR_ADDR 0xFFC00CA4 /* DMA Channel 2 Current Address Register */ +#define DMA2_IRQ_STATUS 0xFFC00CA8 /* DMA Channel 2 Interrupt/Status Register */ +#define DMA2_PERIPHERAL_MAP 0xFFC00CAC /* DMA Channel 2 Peripheral Map Register */ +#define DMA2_CURR_X_COUNT 0xFFC00CB0 /* DMA Channel 2 Current X Count Register */ +#define DMA2_CURR_Y_COUNT 0xFFC00CB8 /* DMA Channel 2 Current Y Count Register */ + +#define DMA3_NEXT_DESC_PTR 0xFFC00CC0 /* DMA Channel 3 Next Descriptor Pointer Register */ +#define DMA3_START_ADDR 0xFFC00CC4 /* DMA Channel 3 Start Address Register */ +#define DMA3_CONFIG 0xFFC00CC8 /* DMA Channel 3 Configuration Register */ +#define DMA3_X_COUNT 0xFFC00CD0 /* DMA Channel 3 X Count Register */ +#define DMA3_X_MODIFY 0xFFC00CD4 /* DMA Channel 3 X Modify Register */ +#define DMA3_Y_COUNT 0xFFC00CD8 /* DMA Channel 3 Y Count Register */ +#define DMA3_Y_MODIFY 0xFFC00CDC /* DMA Channel 3 Y Modify Register */ +#define DMA3_CURR_DESC_PTR 0xFFC00CE0 /* DMA Channel 3 Current Descriptor Pointer Register */ +#define DMA3_CURR_ADDR 0xFFC00CE4 /* DMA Channel 3 Current Address Register */ +#define DMA3_IRQ_STATUS 0xFFC00CE8 /* DMA Channel 3 Interrupt/Status Register */ +#define DMA3_PERIPHERAL_MAP 0xFFC00CEC /* DMA Channel 3 Peripheral Map Register */ +#define DMA3_CURR_X_COUNT 0xFFC00CF0 /* DMA Channel 3 Current X Count Register */ +#define DMA3_CURR_Y_COUNT 0xFFC00CF8 /* DMA Channel 3 Current Y Count Register */ + +#define DMA4_NEXT_DESC_PTR 0xFFC00D00 /* DMA Channel 4 Next Descriptor Pointer Register */ +#define DMA4_START_ADDR 0xFFC00D04 /* DMA Channel 4 Start Address Register */ +#define DMA4_CONFIG 0xFFC00D08 /* DMA Channel 4 Configuration Register */ +#define DMA4_X_COUNT 0xFFC00D10 /* DMA Channel 4 X Count Register */ +#define DMA4_X_MODIFY 0xFFC00D14 /* DMA Channel 4 X Modify Register */ +#define DMA4_Y_COUNT 0xFFC00D18 /* DMA Channel 4 Y Count Register */ +#define DMA4_Y_MODIFY 0xFFC00D1C /* DMA Channel 4 Y Modify Register */ +#define DMA4_CURR_DESC_PTR 0xFFC00D20 /* DMA Channel 4 Current Descriptor Pointer Register */ +#define DMA4_CURR_ADDR 0xFFC00D24 /* DMA Channel 4 Current Address Register */ +#define DMA4_IRQ_STATUS 0xFFC00D28 /* DMA Channel 4 Interrupt/Status Register */ +#define DMA4_PERIPHERAL_MAP 0xFFC00D2C /* DMA Channel 4 Peripheral Map Register */ +#define DMA4_CURR_X_COUNT 0xFFC00D30 /* DMA Channel 4 Current X Count Register */ +#define DMA4_CURR_Y_COUNT 0xFFC00D38 /* DMA Channel 4 Current Y Count Register */ + +#define DMA5_NEXT_DESC_PTR 0xFFC00D40 /* DMA Channel 5 Next Descriptor Pointer Register */ +#define DMA5_START_ADDR 0xFFC00D44 /* DMA Channel 5 Start Address Register */ +#define DMA5_CONFIG 0xFFC00D48 /* DMA Channel 5 Configuration Register */ +#define DMA5_X_COUNT 0xFFC00D50 /* DMA Channel 5 X Count Register */ +#define DMA5_X_MODIFY 0xFFC00D54 /* DMA Channel 5 X Modify Register */ +#define DMA5_Y_COUNT 0xFFC00D58 /* DMA Channel 5 Y Count Register */ +#define DMA5_Y_MODIFY 0xFFC00D5C /* DMA Channel 5 Y Modify Register */ +#define DMA5_CURR_DESC_PTR 0xFFC00D60 /* DMA Channel 5 Current Descriptor Pointer Register */ +#define DMA5_CURR_ADDR 0xFFC00D64 /* DMA Channel 5 Current Address Register */ +#define DMA5_IRQ_STATUS 0xFFC00D68 /* DMA Channel 5 Interrupt/Status Register */ +#define DMA5_PERIPHERAL_MAP 0xFFC00D6C /* DMA Channel 5 Peripheral Map Register */ +#define DMA5_CURR_X_COUNT 0xFFC00D70 /* DMA Channel 5 Current X Count Register */ +#define DMA5_CURR_Y_COUNT 0xFFC00D78 /* DMA Channel 5 Current Y Count Register */ + +#define DMA6_NEXT_DESC_PTR 0xFFC00D80 /* DMA Channel 6 Next Descriptor Pointer Register */ +#define DMA6_START_ADDR 0xFFC00D84 /* DMA Channel 6 Start Address Register */ +#define DMA6_CONFIG 0xFFC00D88 /* DMA Channel 6 Configuration Register */ +#define DMA6_X_COUNT 0xFFC00D90 /* DMA Channel 6 X Count Register */ +#define DMA6_X_MODIFY 0xFFC00D94 /* DMA Channel 6 X Modify Register */ +#define DMA6_Y_COUNT 0xFFC00D98 /* DMA Channel 6 Y Count Register */ +#define DMA6_Y_MODIFY 0xFFC00D9C /* DMA Channel 6 Y Modify Register */ +#define DMA6_CURR_DESC_PTR 0xFFC00DA0 /* DMA Channel 6 Current Descriptor Pointer Register */ +#define DMA6_CURR_ADDR 0xFFC00DA4 /* DMA Channel 6 Current Address Register */ +#define DMA6_IRQ_STATUS 0xFFC00DA8 /* DMA Channel 6 Interrupt/Status Register */ +#define DMA6_PERIPHERAL_MAP 0xFFC00DAC /* DMA Channel 6 Peripheral Map Register */ +#define DMA6_CURR_X_COUNT 0xFFC00DB0 /* DMA Channel 6 Current X Count Register */ +#define DMA6_CURR_Y_COUNT 0xFFC00DB8 /* DMA Channel 6 Current Y Count Register */ + +#define DMA7_NEXT_DESC_PTR 0xFFC00DC0 /* DMA Channel 7 Next Descriptor Pointer Register */ +#define DMA7_START_ADDR 0xFFC00DC4 /* DMA Channel 7 Start Address Register */ +#define DMA7_CONFIG 0xFFC00DC8 /* DMA Channel 7 Configuration Register */ +#define DMA7_X_COUNT 0xFFC00DD0 /* DMA Channel 7 X Count Register */ +#define DMA7_X_MODIFY 0xFFC00DD4 /* DMA Channel 7 X Modify Register */ +#define DMA7_Y_COUNT 0xFFC00DD8 /* DMA Channel 7 Y Count Register */ +#define DMA7_Y_MODIFY 0xFFC00DDC /* DMA Channel 7 Y Modify Register */ +#define DMA7_CURR_DESC_PTR 0xFFC00DE0 /* DMA Channel 7 Current Descriptor Pointer Register */ +#define DMA7_CURR_ADDR 0xFFC00DE4 /* DMA Channel 7 Current Address Register */ +#define DMA7_IRQ_STATUS 0xFFC00DE8 /* DMA Channel 7 Interrupt/Status Register */ +#define DMA7_PERIPHERAL_MAP 0xFFC00DEC /* DMA Channel 7 Peripheral Map Register */ +#define DMA7_CURR_X_COUNT 0xFFC00DF0 /* DMA Channel 7 Current X Count Register */ +#define DMA7_CURR_Y_COUNT 0xFFC00DF8 /* DMA Channel 7 Current Y Count Register */ + +#define DMA8_NEXT_DESC_PTR 0xFFC00E00 /* DMA Channel 8 Next Descriptor Pointer Register */ +#define DMA8_START_ADDR 0xFFC00E04 /* DMA Channel 8 Start Address Register */ +#define DMA8_CONFIG 0xFFC00E08 /* DMA Channel 8 Configuration Register */ +#define DMA8_X_COUNT 0xFFC00E10 /* DMA Channel 8 X Count Register */ +#define DMA8_X_MODIFY 0xFFC00E14 /* DMA Channel 8 X Modify Register */ +#define DMA8_Y_COUNT 0xFFC00E18 /* DMA Channel 8 Y Count Register */ +#define DMA8_Y_MODIFY 0xFFC00E1C /* DMA Channel 8 Y Modify Register */ +#define DMA8_CURR_DESC_PTR 0xFFC00E20 /* DMA Channel 8 Current Descriptor Pointer Register */ +#define DMA8_CURR_ADDR 0xFFC00E24 /* DMA Channel 8 Current Address Register */ +#define DMA8_IRQ_STATUS 0xFFC00E28 /* DMA Channel 8 Interrupt/Status Register */ +#define DMA8_PERIPHERAL_MAP 0xFFC00E2C /* DMA Channel 8 Peripheral Map Register */ +#define DMA8_CURR_X_COUNT 0xFFC00E30 /* DMA Channel 8 Current X Count Register */ +#define DMA8_CURR_Y_COUNT 0xFFC00E38 /* DMA Channel 8 Current Y Count Register */ + +#define DMA9_NEXT_DESC_PTR 0xFFC00E40 /* DMA Channel 9 Next Descriptor Pointer Register */ +#define DMA9_START_ADDR 0xFFC00E44 /* DMA Channel 9 Start Address Register */ +#define DMA9_CONFIG 0xFFC00E48 /* DMA Channel 9 Configuration Register */ +#define DMA9_X_COUNT 0xFFC00E50 /* DMA Channel 9 X Count Register */ +#define DMA9_X_MODIFY 0xFFC00E54 /* DMA Channel 9 X Modify Register */ +#define DMA9_Y_COUNT 0xFFC00E58 /* DMA Channel 9 Y Count Register */ +#define DMA9_Y_MODIFY 0xFFC00E5C /* DMA Channel 9 Y Modify Register */ +#define DMA9_CURR_DESC_PTR 0xFFC00E60 /* DMA Channel 9 Current Descriptor Pointer Register */ +#define DMA9_CURR_ADDR 0xFFC00E64 /* DMA Channel 9 Current Address Register */ +#define DMA9_IRQ_STATUS 0xFFC00E68 /* DMA Channel 9 Interrupt/Status Register */ +#define DMA9_PERIPHERAL_MAP 0xFFC00E6C /* DMA Channel 9 Peripheral Map Register */ +#define DMA9_CURR_X_COUNT 0xFFC00E70 /* DMA Channel 9 Current X Count Register */ +#define DMA9_CURR_Y_COUNT 0xFFC00E78 /* DMA Channel 9 Current Y Count Register */ + +#define DMA10_NEXT_DESC_PTR 0xFFC00E80 /* DMA Channel 10 Next Descriptor Pointer Register */ +#define DMA10_START_ADDR 0xFFC00E84 /* DMA Channel 10 Start Address Register */ +#define DMA10_CONFIG 0xFFC00E88 /* DMA Channel 10 Configuration Register */ +#define DMA10_X_COUNT 0xFFC00E90 /* DMA Channel 10 X Count Register */ +#define DMA10_X_MODIFY 0xFFC00E94 /* DMA Channel 10 X Modify Register */ +#define DMA10_Y_COUNT 0xFFC00E98 /* DMA Channel 10 Y Count Register */ +#define DMA10_Y_MODIFY 0xFFC00E9C /* DMA Channel 10 Y Modify Register */ +#define DMA10_CURR_DESC_PTR 0xFFC00EA0 /* DMA Channel 10 Current Descriptor Pointer Register */ +#define DMA10_CURR_ADDR 0xFFC00EA4 /* DMA Channel 10 Current Address Register */ +#define DMA10_IRQ_STATUS 0xFFC00EA8 /* DMA Channel 10 Interrupt/Status Register */ +#define DMA10_PERIPHERAL_MAP 0xFFC00EAC /* DMA Channel 10 Peripheral Map Register */ +#define DMA10_CURR_X_COUNT 0xFFC00EB0 /* DMA Channel 10 Current X Count Register */ +#define DMA10_CURR_Y_COUNT 0xFFC00EB8 /* DMA Channel 10 Current Y Count Register */ + +#define DMA11_NEXT_DESC_PTR 0xFFC00EC0 /* DMA Channel 11 Next Descriptor Pointer Register */ +#define DMA11_START_ADDR 0xFFC00EC4 /* DMA Channel 11 Start Address Register */ +#define DMA11_CONFIG 0xFFC00EC8 /* DMA Channel 11 Configuration Register */ +#define DMA11_X_COUNT 0xFFC00ED0 /* DMA Channel 11 X Count Register */ +#define DMA11_X_MODIFY 0xFFC00ED4 /* DMA Channel 11 X Modify Register */ +#define DMA11_Y_COUNT 0xFFC00ED8 /* DMA Channel 11 Y Count Register */ +#define DMA11_Y_MODIFY 0xFFC00EDC /* DMA Channel 11 Y Modify Register */ +#define DMA11_CURR_DESC_PTR 0xFFC00EE0 /* DMA Channel 11 Current Descriptor Pointer Register */ +#define DMA11_CURR_ADDR 0xFFC00EE4 /* DMA Channel 11 Current Address Register */ +#define DMA11_IRQ_STATUS 0xFFC00EE8 /* DMA Channel 11 Interrupt/Status Register */ +#define DMA11_PERIPHERAL_MAP 0xFFC00EEC /* DMA Channel 11 Peripheral Map Register */ +#define DMA11_CURR_X_COUNT 0xFFC00EF0 /* DMA Channel 11 Current X Count Register */ +#define DMA11_CURR_Y_COUNT 0xFFC00EF8 /* DMA Channel 11 Current Y Count Register */ + +#define MDMA_D0_NEXT_DESC_PTR 0xFFC00F00 /* MemDMA Stream 0 Destination Next Descriptor Pointer Register */ +#define MDMA_D0_START_ADDR 0xFFC00F04 /* MemDMA Stream 0 Destination Start Address Register */ +#define MDMA_D0_CONFIG 0xFFC00F08 /* MemDMA Stream 0 Destination Configuration Register */ +#define MDMA_D0_X_COUNT 0xFFC00F10 /* MemDMA Stream 0 Destination X Count Register */ +#define MDMA_D0_X_MODIFY 0xFFC00F14 /* MemDMA Stream 0 Destination X Modify Register */ +#define MDMA_D0_Y_COUNT 0xFFC00F18 /* MemDMA Stream 0 Destination Y Count Register */ +#define MDMA_D0_Y_MODIFY 0xFFC00F1C /* MemDMA Stream 0 Destination Y Modify Register */ +#define MDMA_D0_CURR_DESC_PTR 0xFFC00F20 /* MemDMA Stream 0 Destination Current Descriptor Pointer Register */ +#define MDMA_D0_CURR_ADDR 0xFFC00F24 /* MemDMA Stream 0 Destination Current Address Register */ +#define MDMA_D0_IRQ_STATUS 0xFFC00F28 /* MemDMA Stream 0 Destination Interrupt/Status Register */ +#define MDMA_D0_PERIPHERAL_MAP 0xFFC00F2C /* MemDMA Stream 0 Destination Peripheral Map Register */ +#define MDMA_D0_CURR_X_COUNT 0xFFC00F30 /* MemDMA Stream 0 Destination Current X Count Register */ +#define MDMA_D0_CURR_Y_COUNT 0xFFC00F38 /* MemDMA Stream 0 Destination Current Y Count Register */ + +#define MDMA_S0_NEXT_DESC_PTR 0xFFC00F40 /* MemDMA Stream 0 Source Next Descriptor Pointer Register */ +#define MDMA_S0_START_ADDR 0xFFC00F44 /* MemDMA Stream 0 Source Start Address Register */ +#define MDMA_S0_CONFIG 0xFFC00F48 /* MemDMA Stream 0 Source Configuration Register */ +#define MDMA_S0_X_COUNT 0xFFC00F50 /* MemDMA Stream 0 Source X Count Register */ +#define MDMA_S0_X_MODIFY 0xFFC00F54 /* MemDMA Stream 0 Source X Modify Register */ +#define MDMA_S0_Y_COUNT 0xFFC00F58 /* MemDMA Stream 0 Source Y Count Register */ +#define MDMA_S0_Y_MODIFY 0xFFC00F5C /* MemDMA Stream 0 Source Y Modify Register */ +#define MDMA_S0_CURR_DESC_PTR 0xFFC00F60 /* MemDMA Stream 0 Source Current Descriptor Pointer Register */ +#define MDMA_S0_CURR_ADDR 0xFFC00F64 /* MemDMA Stream 0 Source Current Address Register */ +#define MDMA_S0_IRQ_STATUS 0xFFC00F68 /* MemDMA Stream 0 Source Interrupt/Status Register */ +#define MDMA_S0_PERIPHERAL_MAP 0xFFC00F6C /* MemDMA Stream 0 Source Peripheral Map Register */ +#define MDMA_S0_CURR_X_COUNT 0xFFC00F70 /* MemDMA Stream 0 Source Current X Count Register */ +#define MDMA_S0_CURR_Y_COUNT 0xFFC00F78 /* MemDMA Stream 0 Source Current Y Count Register */ + +#define MDMA_D1_NEXT_DESC_PTR 0xFFC00F80 /* MemDMA Stream 1 Destination Next Descriptor Pointer Register */ +#define MDMA_D1_START_ADDR 0xFFC00F84 /* MemDMA Stream 1 Destination Start Address Register */ +#define MDMA_D1_CONFIG 0xFFC00F88 /* MemDMA Stream 1 Destination Configuration Register */ +#define MDMA_D1_X_COUNT 0xFFC00F90 /* MemDMA Stream 1 Destination X Count Register */ +#define MDMA_D1_X_MODIFY 0xFFC00F94 /* MemDMA Stream 1 Destination X Modify Register */ +#define MDMA_D1_Y_COUNT 0xFFC00F98 /* MemDMA Stream 1 Destination Y Count Register */ +#define MDMA_D1_Y_MODIFY 0xFFC00F9C /* MemDMA Stream 1 Destination Y Modify Register */ +#define MDMA_D1_CURR_DESC_PTR 0xFFC00FA0 /* MemDMA Stream 1 Destination Current Descriptor Pointer Register */ +#define MDMA_D1_CURR_ADDR 0xFFC00FA4 /* MemDMA Stream 1 Destination Current Address Register */ +#define MDMA_D1_IRQ_STATUS 0xFFC00FA8 /* MemDMA Stream 1 Destination Interrupt/Status Register */ +#define MDMA_D1_PERIPHERAL_MAP 0xFFC00FAC /* MemDMA Stream 1 Destination Peripheral Map Register */ +#define MDMA_D1_CURR_X_COUNT 0xFFC00FB0 /* MemDMA Stream 1 Destination Current X Count Register */ +#define MDMA_D1_CURR_Y_COUNT 0xFFC00FB8 /* MemDMA Stream 1 Destination Current Y Count Register */ + +#define MDMA_S1_NEXT_DESC_PTR 0xFFC00FC0 /* MemDMA Stream 1 Source Next Descriptor Pointer Register */ +#define MDMA_S1_START_ADDR 0xFFC00FC4 /* MemDMA Stream 1 Source Start Address Register */ +#define MDMA_S1_CONFIG 0xFFC00FC8 /* MemDMA Stream 1 Source Configuration Register */ +#define MDMA_S1_X_COUNT 0xFFC00FD0 /* MemDMA Stream 1 Source X Count Register */ +#define MDMA_S1_X_MODIFY 0xFFC00FD4 /* MemDMA Stream 1 Source X Modify Register */ +#define MDMA_S1_Y_COUNT 0xFFC00FD8 /* MemDMA Stream 1 Source Y Count Register */ +#define MDMA_S1_Y_MODIFY 0xFFC00FDC /* MemDMA Stream 1 Source Y Modify Register */ +#define MDMA_S1_CURR_DESC_PTR 0xFFC00FE0 /* MemDMA Stream 1 Source Current Descriptor Pointer Register */ +#define MDMA_S1_CURR_ADDR 0xFFC00FE4 /* MemDMA Stream 1 Source Current Address Register */ +#define MDMA_S1_IRQ_STATUS 0xFFC00FE8 /* MemDMA Stream 1 Source Interrupt/Status Register */ +#define MDMA_S1_PERIPHERAL_MAP 0xFFC00FEC /* MemDMA Stream 1 Source Peripheral Map Register */ +#define MDMA_S1_CURR_X_COUNT 0xFFC00FF0 /* MemDMA Stream 1 Source Current X Count Register */ +#define MDMA_S1_CURR_Y_COUNT 0xFFC00FF8 /* MemDMA Stream 1 Source Current Y Count Register */ + + +/* Parallel Peripheral Interface (0xFFC01000 - 0xFFC010FF) */ +#define PPI_CONTROL 0xFFC01000 /* PPI Control Register */ +#define PPI_STATUS 0xFFC01004 /* PPI Status Register */ +#define PPI_COUNT 0xFFC01008 /* PPI Transfer Count Register */ +#define PPI_DELAY 0xFFC0100C /* PPI Delay Count Register */ +#define PPI_FRAME 0xFFC01010 /* PPI Frame Length Register */ + + +/* Two-Wire Interface (0xFFC01400 - 0xFFC014FF) */ +#define TWI0_REGBASE 0xFFC01400 +#define TWI_CLKDIV 0xFFC01400 /* Serial Clock Divider Register */ +#define TWI_CONTROL 0xFFC01404 /* TWI Control Register */ +#define TWI_SLAVE_CTL 0xFFC01408 /* Slave Mode Control Register */ +#define TWI_SLAVE_STAT 0xFFC0140C /* Slave Mode Status Register */ +#define TWI_SLAVE_ADDR 0xFFC01410 /* Slave Mode Address Register */ +#define TWI_MASTER_CTL 0xFFC01414 /* Master Mode Control Register */ +#define TWI_MASTER_STAT 0xFFC01418 /* Master Mode Status Register */ +#define TWI_MASTER_ADDR 0xFFC0141C /* Master Mode Address Register */ +#define TWI_INT_STAT 0xFFC01420 /* TWI Interrupt Status Register */ +#define TWI_INT_MASK 0xFFC01424 /* TWI Master Interrupt Mask Register */ +#define TWI_FIFO_CTL 0xFFC01428 /* FIFO Control Register */ +#define TWI_FIFO_STAT 0xFFC0142C /* FIFO Status Register */ +#define TWI_XMT_DATA8 0xFFC01480 /* FIFO Transmit Data Single Byte Register */ +#define TWI_XMT_DATA16 0xFFC01484 /* FIFO Transmit Data Double Byte Register */ +#define TWI_RCV_DATA8 0xFFC01488 /* FIFO Receive Data Single Byte Register */ +#define TWI_RCV_DATA16 0xFFC0148C /* FIFO Receive Data Double Byte Register */ + + +/* General Purpose I/O Port G (0xFFC01500 - 0xFFC015FF) */ +#define PORTGIO 0xFFC01500 /* Port G I/O Pin State Specify Register */ +#define PORTGIO_CLEAR 0xFFC01504 /* Port G I/O Peripheral Interrupt Clear Register */ +#define PORTGIO_SET 0xFFC01508 /* Port G I/O Peripheral Interrupt Set Register */ +#define PORTGIO_TOGGLE 0xFFC0150C /* Port G I/O Pin State Toggle Register */ +#define PORTGIO_MASKA 0xFFC01510 /* Port G I/O Mask State Specify Interrupt A Register */ +#define PORTGIO_MASKA_CLEAR 0xFFC01514 /* Port G I/O Mask Disable Interrupt A Register */ +#define PORTGIO_MASKA_SET 0xFFC01518 /* Port G I/O Mask Enable Interrupt A Register */ +#define PORTGIO_MASKA_TOGGLE 0xFFC0151C /* Port G I/O Mask Toggle Enable Interrupt A Register */ +#define PORTGIO_MASKB 0xFFC01520 /* Port G I/O Mask State Specify Interrupt B Register */ +#define PORTGIO_MASKB_CLEAR 0xFFC01524 /* Port G I/O Mask Disable Interrupt B Register */ +#define PORTGIO_MASKB_SET 0xFFC01528 /* Port G I/O Mask Enable Interrupt B Register */ +#define PORTGIO_MASKB_TOGGLE 0xFFC0152C /* Port G I/O Mask Toggle Enable Interrupt B Register */ +#define PORTGIO_DIR 0xFFC01530 /* Port G I/O Direction Register */ +#define PORTGIO_POLAR 0xFFC01534 /* Port G I/O Source Polarity Register */ +#define PORTGIO_EDGE 0xFFC01538 /* Port G I/O Source Sensitivity Register */ +#define PORTGIO_BOTH 0xFFC0153C /* Port G I/O Set on BOTH Edges Register */ +#define PORTGIO_INEN 0xFFC01540 /* Port G I/O Input Enable Register */ + + +/* General Purpose I/O Port H (0xFFC01700 - 0xFFC017FF) */ +#define PORTHIO 0xFFC01700 /* Port H I/O Pin State Specify Register */ +#define PORTHIO_CLEAR 0xFFC01704 /* Port H I/O Peripheral Interrupt Clear Register */ +#define PORTHIO_SET 0xFFC01708 /* Port H I/O Peripheral Interrupt Set Register */ +#define PORTHIO_TOGGLE 0xFFC0170C /* Port H I/O Pin State Toggle Register */ +#define PORTHIO_MASKA 0xFFC01710 /* Port H I/O Mask State Specify Interrupt A Register */ +#define PORTHIO_MASKA_CLEAR 0xFFC01714 /* Port H I/O Mask Disable Interrupt A Register */ +#define PORTHIO_MASKA_SET 0xFFC01718 /* Port H I/O Mask Enable Interrupt A Register */ +#define PORTHIO_MASKA_TOGGLE 0xFFC0171C /* Port H I/O Mask Toggle Enable Interrupt A Register */ +#define PORTHIO_MASKB 0xFFC01720 /* Port H I/O Mask State Specify Interrupt B Register */ +#define PORTHIO_MASKB_CLEAR 0xFFC01724 /* Port H I/O Mask Disable Interrupt B Register */ +#define PORTHIO_MASKB_SET 0xFFC01728 /* Port H I/O Mask Enable Interrupt B Register */ +#define PORTHIO_MASKB_TOGGLE 0xFFC0172C /* Port H I/O Mask Toggle Enable Interrupt B Register */ +#define PORTHIO_DIR 0xFFC01730 /* Port H I/O Direction Register */ +#define PORTHIO_POLAR 0xFFC01734 /* Port H I/O Source Polarity Register */ +#define PORTHIO_EDGE 0xFFC01738 /* Port H I/O Source Sensitivity Register */ +#define PORTHIO_BOTH 0xFFC0173C /* Port H I/O Set on BOTH Edges Register */ +#define PORTHIO_INEN 0xFFC01740 /* Port H I/O Input Enable Register */ + + +/* UART1 Controller (0xFFC02000 - 0xFFC020FF) */ +#define UART1_THR 0xFFC02000 /* Transmit Holding register */ +#define UART1_RBR 0xFFC02000 /* Receive Buffer register */ +#define UART1_DLL 0xFFC02000 /* Divisor Latch (Low-Byte) */ +#define UART1_IER 0xFFC02004 /* Interrupt Enable Register */ +#define UART1_DLH 0xFFC02004 /* Divisor Latch (High-Byte) */ +#define UART1_IIR 0xFFC02008 /* Interrupt Identification Register */ +#define UART1_LCR 0xFFC0200C /* Line Control Register */ +#define UART1_MCR 0xFFC02010 /* Modem Control Register */ +#define UART1_LSR 0xFFC02014 /* Line Status Register */ +#define UART1_MSR 0xFFC02018 /* Modem Status Register */ +#define UART1_SCR 0xFFC0201C /* SCR Scratch Register */ +#define UART1_GCTL 0xFFC02024 /* Global Control Register */ + + +/* Pin Control Registers (0xFFC03200 - 0xFFC032FF) */ +#define PORTF_FER 0xFFC03200 /* Port F Function Enable Register (Alternate/Flag*) */ +#define PORTG_FER 0xFFC03204 /* Port G Function Enable Register (Alternate/Flag*) */ +#define PORTH_FER 0xFFC03208 /* Port H Function Enable Register (Alternate/Flag*) */ +#define BFIN_PORT_MUX 0xFFC0320C /* Port Multiplexer Control Register */ + + +/* Handshake MDMA Registers (0xFFC03300 - 0xFFC033FF) */ +#define HMDMA0_CONTROL 0xFFC03300 /* Handshake MDMA0 Control Register */ +#define HMDMA0_ECINIT 0xFFC03304 /* HMDMA0 Initial Edge Count Register */ +#define HMDMA0_BCINIT 0xFFC03308 /* HMDMA0 Initial Block Count Register */ +#define HMDMA0_ECURGENT 0xFFC0330C /* HMDMA0 Urgent Edge Count Threshhold Register */ +#define HMDMA0_ECOVERFLOW 0xFFC03310 /* HMDMA0 Edge Count Overflow Interrupt Register */ +#define HMDMA0_ECOUNT 0xFFC03314 /* HMDMA0 Current Edge Count Register */ +#define HMDMA0_BCOUNT 0xFFC03318 /* HMDMA0 Current Block Count Register */ + +#define HMDMA1_CONTROL 0xFFC03340 /* Handshake MDMA1 Control Register */ +#define HMDMA1_ECINIT 0xFFC03344 /* HMDMA1 Initial Edge Count Register */ +#define HMDMA1_BCINIT 0xFFC03348 /* HMDMA1 Initial Block Count Register */ +#define HMDMA1_ECURGENT 0xFFC0334C /* HMDMA1 Urgent Edge Count Threshhold Register */ +#define HMDMA1_ECOVERFLOW 0xFFC03350 /* HMDMA1 Edge Count Overflow Interrupt Register */ +#define HMDMA1_ECOUNT 0xFFC03354 /* HMDMA1 Current Edge Count Register */ +#define HMDMA1_BCOUNT 0xFFC03358 /* HMDMA1 Current Block Count Register */ + + +/* GPIO PIN mux (0xFFC03210 - OxFFC03288) */ +#define PORTF_MUX 0xFFC03210 /* Port F mux control */ +#define PORTG_MUX 0xFFC03214 /* Port G mux control */ +#define PORTH_MUX 0xFFC03218 /* Port H mux control */ +#define PORTF_DRIVE 0xFFC03220 /* Port F drive strength control */ +#define PORTG_DRIVE 0xFFC03224 /* Port G drive strength control */ +#define PORTH_DRIVE 0xFFC03228 /* Port H drive strength control */ +#define PORTF_SLEW 0xFFC03230 /* Port F slew control */ +#define PORTG_SLEW 0xFFC03234 /* Port G slew control */ +#define PORTH_SLEW 0xFFC03238 /* Port H slew control */ +#define PORTF_HYSTERISIS 0xFFC03240 /* Port F Schmitt trigger control */ +#define PORTG_HYSTERISIS 0xFFC03244 /* Port G Schmitt trigger control */ +#define PORTH_HYSTERISIS 0xFFC03248 /* Port H Schmitt trigger control */ +#define MISCPORT_DRIVE 0xFFC03280 /* Misc Port drive strength control */ +#define MISCPORT_SLEW 0xFFC03284 /* Misc Port slew control */ +#define MISCPORT_HYSTERISIS 0xFFC03288 /* Misc Port Schmitt trigger control */ + + +/*********************************************************************************** +** System MMR Register Bits And Macros +** +** Disclaimer: All macros are intended to make C and Assembly code more readable. +** Use these macros carefully, as any that do left shifts for field +** depositing will result in the lower order bits being destroyed. Any +** macro that shifts left to properly position the bit-field should be +** used as part of an OR to initialize a register and NOT as a dynamic +** modifier UNLESS the lower order bits are saved and ORed back in when +** the macro is used. +*************************************************************************************/ +/* +** ********************* PLL AND RESET MASKS ****************************************/ +/* PLL_CTL Masks */ +#define DF 0x0001 /* 0: PLL = CLKIN, 1: PLL = CLKIN/2 */ +#define PLL_OFF 0x0002 /* PLL Not Powered */ +#define STOPCK 0x0008 /* Core Clock Off */ +#define PDWN 0x0020 /* Enter Deep Sleep Mode */ +#define IN_DELAY 0x0040 /* Add 200ps Delay To EBIU Input Latches */ +#define OUT_DELAY 0x0080 /* Add 200ps Delay To EBIU Output Signals */ +#define BYPASS 0x0100 /* Bypass the PLL */ +#define MSEL 0x7E00 /* Multiplier Select For CCLK/VCO Factors */ +/* PLL_CTL Macros (Only Use With Logic OR While Setting Lower Order Bits) */ +#define SET_MSEL(x) (((x)&0x3F) << 0x9) /* Set MSEL = 0-63 --> VCO = CLKIN*MSEL */ + +/* PLL_DIV Masks */ +#define SSEL 0x000F /* System Select */ +#define CSEL 0x0030 /* Core Select */ +#define CSEL_DIV1 0x0000 /* CCLK = VCO / 1 */ +#define CSEL_DIV2 0x0010 /* CCLK = VCO / 2 */ +#define CSEL_DIV4 0x0020 /* CCLK = VCO / 4 */ +#define CSEL_DIV8 0x0030 /* CCLK = VCO / 8 */ +/* PLL_DIV Macros */ +#define SET_SSEL(x) ((x)&0xF) /* Set SSEL = 0-15 --> SCLK = VCO/SSEL */ + +/* VR_CTL Masks */ +#define FREQ 0x3000 /* Switching Oscillator Frequency For Regulator */ +#define HIBERNATE 0x0000 /* Powerdown/Bypass On-Board Regulation */ + +#define VLEV 0x00F0 /* Internal Voltage Level */ +#define VLEV_085 0x0060 /* VLEV = 0.85 V (-5% - +10% Accuracy) */ +#define VLEV_090 0x0070 /* VLEV = 0.90 V (-5% - +10% Accuracy) */ +#define VLEV_095 0x0080 /* VLEV = 0.95 V (-5% - +10% Accuracy) */ +#define VLEV_100 0x0090 /* VLEV = 1.00 V (-5% - +10% Accuracy) */ +#define VLEV_105 0x00A0 /* VLEV = 1.05 V (-5% - +10% Accuracy) */ +#define VLEV_110 0x00B0 /* VLEV = 1.10 V (-5% - +10% Accuracy) */ +#define VLEV_115 0x00C0 /* VLEV = 1.15 V (-5% - +10% Accuracy) */ +#define VLEV_120 0x00D0 /* VLEV = 1.20 V (-5% - +10% Accuracy) */ +#define VLEV_125 0x00E0 /* VLEV = 1.25 V (-5% - +10% Accuracy) */ +#define VLEV_130 0x00F0 /* VLEV = 1.30 V (-5% - +10% Accuracy) */ + +#define WAKE 0x0100 /* Enable RTC/Reset Wakeup From Hibernate */ +#define USBWE 0x0200 /* Enable USB Wakeup From Hibernate */ +#define PHYWE 0x0400 /* Enable PHY Wakeup From Hibernate */ +#define CLKBUFOE 0x4000 /* CLKIN Buffer Output Enable */ +#define PHYCLKOE CLKBUFOE /* Alternative legacy name for the above */ +#define SCKELOW 0x8000 /* Enable Drive CKE Low During Reset */ + +/* PLL_STAT Masks */ +#define ACTIVE_PLLENABLED 0x0001 /* Processor In Active Mode With PLL Enabled */ +#define FULL_ON 0x0002 /* Processor In Full On Mode */ +#define ACTIVE_PLLDISABLED 0x0004 /* Processor In Active Mode With PLL Disabled */ +#define PLL_LOCKED 0x0020 /* PLL_LOCKCNT Has Been Reached */ + +/* CHIPID Masks */ +#define CHIPID_VERSION 0xF0000000 +#define CHIPID_FAMILY 0x0FFFF000 +#define CHIPID_MANUFACTURE 0x00000FFE + +/* SWRST Masks */ +#define SYSTEM_RESET 0x0007 /* Initiates A System Software Reset */ +#define DOUBLE_FAULT 0x0008 /* Core Double Fault Causes Reset */ +#define RESET_DOUBLE 0x2000 /* SW Reset Generated By Core Double-Fault */ +#define RESET_WDOG 0x4000 /* SW Reset Generated By Watchdog Timer */ +#define RESET_SOFTWARE 0x8000 /* SW Reset Occurred Since Last Read Of SWRST */ + +/* SYSCR Masks */ +#define BMODE 0x0007 /* Boot Mode - Latched During HW Reset From Mode Pins */ +#define NOBOOT 0x0010 /* Execute From L1 or ASYNC Bank 0 When BMODE = 0 */ + + +/* ************* SYSTEM INTERRUPT CONTROLLER MASKS *************************************/ +/* Peripheral Masks For SIC_ISR, SIC_IWR, SIC_IMASK */ + +#if 0 +#define IRQ_PLL_WAKEUP 0x00000001 /* PLL Wakeup Interrupt */ + +#define IRQ_ERROR1 0x00000002 /* Error Interrupt (DMA, DMARx Block, DMARx Overflow) */ +#define IRQ_ERROR2 0x00000004 /* Error Interrupt (CAN, Ethernet, SPORTx, PPI, SPI, UARTx) */ +#define IRQ_RTC 0x00000008 /* Real Time Clock Interrupt */ +#define IRQ_DMA0 0x00000010 /* DMA Channel 0 (PPI) Interrupt */ +#define IRQ_DMA3 0x00000020 /* DMA Channel 3 (SPORT0 RX) Interrupt */ +#define IRQ_DMA4 0x00000040 /* DMA Channel 4 (SPORT0 TX) Interrupt */ +#define IRQ_DMA5 0x00000080 /* DMA Channel 5 (SPORT1 RX) Interrupt */ + +#define IRQ_DMA6 0x00000100 /* DMA Channel 6 (SPORT1 TX) Interrupt */ +#define IRQ_TWI 0x00000200 /* TWI Interrupt */ +#define IRQ_DMA7 0x00000400 /* DMA Channel 7 (SPI) Interrupt */ +#define IRQ_DMA8 0x00000800 /* DMA Channel 8 (UART0 RX) Interrupt */ +#define IRQ_DMA9 0x00001000 /* DMA Channel 9 (UART0 TX) Interrupt */ +#define IRQ_DMA10 0x00002000 /* DMA Channel 10 (UART1 RX) Interrupt */ +#define IRQ_DMA11 0x00004000 /* DMA Channel 11 (UART1 TX) Interrupt */ +#define IRQ_CAN_RX 0x00008000 /* CAN Receive Interrupt */ + +#define IRQ_CAN_TX 0x00010000 /* CAN Transmit Interrupt */ +#define IRQ_DMA1 0x00020000 /* DMA Channel 1 (Ethernet RX) Interrupt */ +#define IRQ_PFA_PORTH 0x00020000 /* PF Port H (PF47:32) Interrupt A */ +#define IRQ_DMA2 0x00040000 /* DMA Channel 2 (Ethernet TX) Interrupt */ +#define IRQ_PFB_PORTH 0x00040000 /* PF Port H (PF47:32) Interrupt B */ +#define IRQ_TIMER0 0x00080000 /* Timer 0 Interrupt */ +#define IRQ_TIMER1 0x00100000 /* Timer 1 Interrupt */ +#define IRQ_TIMER2 0x00200000 /* Timer 2 Interrupt */ +#define IRQ_TIMER3 0x00400000 /* Timer 3 Interrupt */ +#define IRQ_TIMER4 0x00800000 /* Timer 4 Interrupt */ + +#define IRQ_TIMER5 0x01000000 /* Timer 5 Interrupt */ +#define IRQ_TIMER6 0x02000000 /* Timer 6 Interrupt */ +#define IRQ_TIMER7 0x04000000 /* Timer 7 Interrupt */ +#define IRQ_PFA_PORTFG 0x08000000 /* PF Ports F&G (PF31:0) Interrupt A */ +#define IRQ_PFB_PORTF 0x80000000 /* PF Port F (PF15:0) Interrupt B */ +#define IRQ_DMA12 0x20000000 /* DMA Channels 12 (MDMA1 Source) RX Interrupt */ +#define IRQ_DMA13 0x20000000 /* DMA Channels 13 (MDMA1 Destination) TX Interrupt */ +#define IRQ_DMA14 0x40000000 /* DMA Channels 14 (MDMA0 Source) RX Interrupt */ +#define IRQ_DMA15 0x40000000 /* DMA Channels 15 (MDMA0 Destination) TX Interrupt */ +#define IRQ_WDOG 0x80000000 /* Software Watchdog Timer Interrupt */ +#define IRQ_PFB_PORTG 0x10000000 /* PF Port G (PF31:16) Interrupt B */ +#endif + +/* SIC_IAR0 Macros */ +#define P0_IVG(x) (((x)&0xF)-7) /* Peripheral #0 assigned IVG #x */ +#define P1_IVG(x) (((x)&0xF)-7) << 0x4 /* Peripheral #1 assigned IVG #x */ +#define P2_IVG(x) (((x)&0xF)-7) << 0x8 /* Peripheral #2 assigned IVG #x */ +#define P3_IVG(x) (((x)&0xF)-7) << 0xC /* Peripheral #3 assigned IVG #x */ +#define P4_IVG(x) (((x)&0xF)-7) << 0x10 /* Peripheral #4 assigned IVG #x */ +#define P5_IVG(x) (((x)&0xF)-7) << 0x14 /* Peripheral #5 assigned IVG #x */ +#define P6_IVG(x) (((x)&0xF)-7) << 0x18 /* Peripheral #6 assigned IVG #x */ +#define P7_IVG(x) (((x)&0xF)-7) << 0x1C /* Peripheral #7 assigned IVG #x */ + +/* SIC_IAR1 Macros */ +#define P8_IVG(x) (((x)&0xF)-7) /* Peripheral #8 assigned IVG #x */ +#define P9_IVG(x) (((x)&0xF)-7) << 0x4 /* Peripheral #9 assigned IVG #x */ +#define P10_IVG(x) (((x)&0xF)-7) << 0x8 /* Peripheral #10 assigned IVG #x */ +#define P11_IVG(x) (((x)&0xF)-7) << 0xC /* Peripheral #11 assigned IVG #x */ +#define P12_IVG(x) (((x)&0xF)-7) << 0x10 /* Peripheral #12 assigned IVG #x */ +#define P13_IVG(x) (((x)&0xF)-7) << 0x14 /* Peripheral #13 assigned IVG #x */ +#define P14_IVG(x) (((x)&0xF)-7) << 0x18 /* Peripheral #14 assigned IVG #x */ +#define P15_IVG(x) (((x)&0xF)-7) << 0x1C /* Peripheral #15 assigned IVG #x */ + +/* SIC_IAR2 Macros */ +#define P16_IVG(x) (((x)&0xF)-7) /* Peripheral #16 assigned IVG #x */ +#define P17_IVG(x) (((x)&0xF)-7) << 0x4 /* Peripheral #17 assigned IVG #x */ +#define P18_IVG(x) (((x)&0xF)-7) << 0x8 /* Peripheral #18 assigned IVG #x */ +#define P19_IVG(x) (((x)&0xF)-7) << 0xC /* Peripheral #19 assigned IVG #x */ +#define P20_IVG(x) (((x)&0xF)-7) << 0x10 /* Peripheral #20 assigned IVG #x */ +#define P21_IVG(x) (((x)&0xF)-7) << 0x14 /* Peripheral #21 assigned IVG #x */ +#define P22_IVG(x) (((x)&0xF)-7) << 0x18 /* Peripheral #22 assigned IVG #x */ +#define P23_IVG(x) (((x)&0xF)-7) << 0x1C /* Peripheral #23 assigned IVG #x */ + +/* SIC_IAR3 Macros */ +#define P24_IVG(x) (((x)&0xF)-7) /* Peripheral #24 assigned IVG #x */ +#define P25_IVG(x) (((x)&0xF)-7) << 0x4 /* Peripheral #25 assigned IVG #x */ +#define P26_IVG(x) (((x)&0xF)-7) << 0x8 /* Peripheral #26 assigned IVG #x */ +#define P27_IVG(x) (((x)&0xF)-7) << 0xC /* Peripheral #27 assigned IVG #x */ +#define P28_IVG(x) (((x)&0xF)-7) << 0x10 /* Peripheral #28 assigned IVG #x */ +#define P29_IVG(x) (((x)&0xF)-7) << 0x14 /* Peripheral #29 assigned IVG #x */ +#define P30_IVG(x) (((x)&0xF)-7) << 0x18 /* Peripheral #30 assigned IVG #x */ +#define P31_IVG(x) (((x)&0xF)-7) << 0x1C /* Peripheral #31 assigned IVG #x */ + + +/* SIC_IMASK Masks */ +#define SIC_UNMASK_ALL 0x00000000 /* Unmask all peripheral interrupts */ +#define SIC_MASK_ALL 0xFFFFFFFF /* Mask all peripheral interrupts */ +#define SIC_MASK(x) (1 << ((x)&0x1F)) /* Mask Peripheral #x interrupt */ +#define SIC_UNMASK(x) (0xFFFFFFFF ^ (1 << ((x)&0x1F))) /* Unmask Peripheral #x interrupt */ + +/* SIC_IWR Masks */ +#define IWR_DISABLE_ALL 0x00000000 /* Wakeup Disable all peripherals */ +#define IWR_ENABLE_ALL 0xFFFFFFFF /* Wakeup Enable all peripherals */ +#define IWR_ENABLE(x) (1 << ((x)&0x1F)) /* Wakeup Enable Peripheral #x */ +#define IWR_DISABLE(x) (0xFFFFFFFF ^ (1 << ((x)&0x1F))) /* Wakeup Disable Peripheral #x */ + + +/* ********* WATCHDOG TIMER MASKS ******************** */ + +/* Watchdog Timer WDOG_CTL Register Masks */ + +#define WDEV(x) (((x)<<1) & 0x0006) /* event generated on roll over */ +#define WDEV_RESET 0x0000 /* generate reset event on roll over */ +#define WDEV_NMI 0x0002 /* generate NMI event on roll over */ +#define WDEV_GPI 0x0004 /* generate GP IRQ on roll over */ +#define WDEV_NONE 0x0006 /* no event on roll over */ +#define WDEN 0x0FF0 /* enable watchdog */ +#define WDDIS 0x0AD0 /* disable watchdog */ +#define WDRO 0x8000 /* watchdog rolled over latch */ + +/* depreciated WDOG_CTL Register Masks for legacy code */ + + +#define ICTL WDEV +#define ENABLE_RESET WDEV_RESET +#define WDOG_RESET WDEV_RESET +#define ENABLE_NMI WDEV_NMI +#define WDOG_NMI WDEV_NMI +#define ENABLE_GPI WDEV_GPI +#define WDOG_GPI WDEV_GPI +#define DISABLE_EVT WDEV_NONE +#define WDOG_NONE WDEV_NONE + +#define TMR_EN WDEN +#define TMR_DIS WDDIS +#define TRO WDRO +#define ICTL_P0 0x01 + #define ICTL_P1 0x02 +#define TRO_P 0x0F + + + +/* *************** REAL TIME CLOCK MASKS **************************/ +/* RTC_STAT and RTC_ALARM Masks */ +#define RTC_SEC 0x0000003F /* Real-Time Clock Seconds */ +#define RTC_MIN 0x00000FC0 /* Real-Time Clock Minutes */ +#define RTC_HR 0x0001F000 /* Real-Time Clock Hours */ +#define RTC_DAY 0xFFFE0000 /* Real-Time Clock Days */ + +/* RTC_ALARM Macro z=day y=hr x=min w=sec */ +#define SET_ALARM(z,y,x,w) ((((z)&0x7FFF)<<0x11)|(((y)&0x1F)<<0xC)|(((x)&0x3F)<<0x6)|((w)&0x3F)) + +/* RTC_ICTL and RTC_ISTAT Masks */ +#define STOPWATCH 0x0001 /* Stopwatch Interrupt Enable */ +#define ALARM 0x0002 /* Alarm Interrupt Enable */ +#define SECOND 0x0004 /* Seconds (1 Hz) Interrupt Enable */ +#define MINUTE 0x0008 /* Minutes Interrupt Enable */ +#define HOUR 0x0010 /* Hours Interrupt Enable */ +#define DAY 0x0020 /* 24 Hours (Days) Interrupt Enable */ +#define DAY_ALARM 0x0040 /* Day Alarm (Day, Hour, Minute, Second) Interrupt Enable */ +#define WRITE_PENDING 0x4000 /* Write Pending Status */ +#define WRITE_COMPLETE 0x8000 /* Write Complete Interrupt Enable */ + +/* RTC_FAST / RTC_PREN Mask */ +#define PREN 0x0001 /* Enable Prescaler, RTC Runs @1 Hz */ + + +/* ************** UART CONTROLLER MASKS *************************/ +/* UARTx_LCR Masks */ +#define WLS(x) (((x)-5) & 0x03) /* Word Length Select */ +#define STB 0x04 /* Stop Bits */ +#define PEN 0x08 /* Parity Enable */ +#define EPS 0x10 /* Even Parity Select */ +#define STP 0x20 /* Stick Parity */ +#define SB 0x40 /* Set Break */ +#define DLAB 0x80 /* Divisor Latch Access */ + +/* UARTx_MCR Mask */ +#define LOOP_ENA 0x10 /* Loopback Mode Enable */ +#define LOOP_ENA_P 0x04 + +/* UARTx_LSR Masks */ +#define DR 0x01 /* Data Ready */ +#define OE 0x02 /* Overrun Error */ +#define PE 0x04 /* Parity Error */ +#define FE 0x08 /* Framing Error */ +#define BI 0x10 /* Break Interrupt */ +#define THRE 0x20 /* THR Empty */ +#define TEMT 0x40 /* TSR and UART_THR Empty */ + +/* UARTx_IER Masks */ +#define ERBFI 0x01 /* Enable Receive Buffer Full Interrupt */ +#define ETBEI 0x02 /* Enable Transmit Buffer Empty Interrupt */ +#define ELSI 0x04 /* Enable RX Status Interrupt */ + +/* UARTx_IIR Masks */ +#define NINT 0x01 /* Pending Interrupt */ +#define IIR_TX_READY 0x02 /* UART_THR empty */ +#define IIR_RX_READY 0x04 /* Receive data ready */ +#define IIR_LINE_CHANGE 0x06 /* Receive line status */ +#define IIR_STATUS 0x06 /* Highest Priority Pending Interrupt */ + +/* UARTx_GCTL Masks */ +#define UCEN 0x01 /* Enable UARTx Clocks */ +#define IREN 0x02 /* Enable IrDA Mode */ +#define TPOLC 0x04 /* IrDA TX Polarity Change */ +#define RPOLC 0x08 /* IrDA RX Polarity Change */ +#define FPE 0x10 /* Force Parity Error On Transmit */ +#define FFE 0x20 /* Force Framing Error On Transmit */ + + +/* *********** SERIAL PERIPHERAL INTERFACE (SPI) MASKS ****************************/ +/* SPI_CTL Masks */ +#define TIMOD 0x0003 /* Transfer Initiate Mode */ +#define RDBR_CORE 0x0000 /* RDBR Read Initiates, IRQ When RDBR Full */ +#define TDBR_CORE 0x0001 /* TDBR Write Initiates, IRQ When TDBR Empty */ +#define RDBR_DMA 0x0002 /* DMA Read, DMA Until FIFO Empty */ +#define TDBR_DMA 0x0003 /* DMA Write, DMA Until FIFO Full */ +#define SZ 0x0004 /* Send Zero (When TDBR Empty, Send Zero/Last*) */ +#define GM 0x0008 /* Get More (When RDBR Full, Overwrite/Discard*) */ +#define PSSE 0x0010 /* Slave-Select Input Enable */ +#define EMISO 0x0020 /* Enable MISO As Output */ +#define SIZE 0x0100 /* Size of Words (16/8* Bits) */ +#define LSBF 0x0200 /* LSB First */ +#define CPHA 0x0400 /* Clock Phase */ +#define CPOL 0x0800 /* Clock Polarity */ +#define MSTR 0x1000 /* Master/Slave* */ +#define WOM 0x2000 /* Write Open Drain Master */ +#define SPE 0x4000 /* SPI Enable */ + +/* SPI_FLG Masks */ +#define FLS1 0x0002 /* Enables SPI_FLOUT1 as SPI Slave-Select Output */ +#define FLS2 0x0004 /* Enables SPI_FLOUT2 as SPI Slave-Select Output */ +#define FLS3 0x0008 /* Enables SPI_FLOUT3 as SPI Slave-Select Output */ +#define FLS4 0x0010 /* Enables SPI_FLOUT4 as SPI Slave-Select Output */ +#define FLS5 0x0020 /* Enables SPI_FLOUT5 as SPI Slave-Select Output */ +#define FLS6 0x0040 /* Enables SPI_FLOUT6 as SPI Slave-Select Output */ +#define FLS7 0x0080 /* Enables SPI_FLOUT7 as SPI Slave-Select Output */ +#define FLG1 0xFDFF /* Activates SPI_FLOUT1 */ +#define FLG2 0xFBFF /* Activates SPI_FLOUT2 */ +#define FLG3 0xF7FF /* Activates SPI_FLOUT3 */ +#define FLG4 0xEFFF /* Activates SPI_FLOUT4 */ +#define FLG5 0xDFFF /* Activates SPI_FLOUT5 */ +#define FLG6 0xBFFF /* Activates SPI_FLOUT6 */ +#define FLG7 0x7FFF /* Activates SPI_FLOUT7 */ + +/* SPI_STAT Masks */ +#define SPIF 0x0001 /* SPI Finished (Single-Word Transfer Complete) */ +#define MODF 0x0002 /* Mode Fault Error (Another Device Tried To Become Master) */ +#define TXE 0x0004 /* Transmission Error (Data Sent With No New Data In TDBR) */ +#define TXS 0x0008 /* SPI_TDBR Data Buffer Status (Full/Empty*) */ +#define RBSY 0x0010 /* Receive Error (Data Received With RDBR Full) */ +#define RXS 0x0020 /* SPI_RDBR Data Buffer Status (Full/Empty*) */ +#define TXCOL 0x0040 /* Transmit Collision Error (Corrupt Data May Have Been Sent) */ + + +/* **************** GENERAL PURPOSE TIMER MASKS **********************/ +/* TIMER_ENABLE Masks */ +#define TIMEN0 0x0001 /* Enable Timer 0 */ +#define TIMEN1 0x0002 /* Enable Timer 1 */ +#define TIMEN2 0x0004 /* Enable Timer 2 */ +#define TIMEN3 0x0008 /* Enable Timer 3 */ +#define TIMEN4 0x0010 /* Enable Timer 4 */ +#define TIMEN5 0x0020 /* Enable Timer 5 */ +#define TIMEN6 0x0040 /* Enable Timer 6 */ +#define TIMEN7 0x0080 /* Enable Timer 7 */ + +/* TIMER_DISABLE Masks */ +#define TIMDIS0 TIMEN0 /* Disable Timer 0 */ +#define TIMDIS1 TIMEN1 /* Disable Timer 1 */ +#define TIMDIS2 TIMEN2 /* Disable Timer 2 */ +#define TIMDIS3 TIMEN3 /* Disable Timer 3 */ +#define TIMDIS4 TIMEN4 /* Disable Timer 4 */ +#define TIMDIS5 TIMEN5 /* Disable Timer 5 */ +#define TIMDIS6 TIMEN6 /* Disable Timer 6 */ +#define TIMDIS7 TIMEN7 /* Disable Timer 7 */ + +/* TIMER_STATUS Masks */ +#define TIMIL0 0x00000001 /* Timer 0 Interrupt */ +#define TIMIL1 0x00000002 /* Timer 1 Interrupt */ +#define TIMIL2 0x00000004 /* Timer 2 Interrupt */ +#define TIMIL3 0x00000008 /* Timer 3 Interrupt */ +#define TOVF_ERR0 0x00000010 /* Timer 0 Counter Overflow */ +#define TOVF_ERR1 0x00000020 /* Timer 1 Counter Overflow */ +#define TOVF_ERR2 0x00000040 /* Timer 2 Counter Overflow */ +#define TOVF_ERR3 0x00000080 /* Timer 3 Counter Overflow */ +#define TRUN0 0x00001000 /* Timer 0 Slave Enable Status */ +#define TRUN1 0x00002000 /* Timer 1 Slave Enable Status */ +#define TRUN2 0x00004000 /* Timer 2 Slave Enable Status */ +#define TRUN3 0x00008000 /* Timer 3 Slave Enable Status */ +#define TIMIL4 0x00010000 /* Timer 4 Interrupt */ +#define TIMIL5 0x00020000 /* Timer 5 Interrupt */ +#define TIMIL6 0x00040000 /* Timer 6 Interrupt */ +#define TIMIL7 0x00080000 /* Timer 7 Interrupt */ +#define TOVF_ERR4 0x00100000 /* Timer 4 Counter Overflow */ +#define TOVF_ERR5 0x00200000 /* Timer 5 Counter Overflow */ +#define TOVF_ERR6 0x00400000 /* Timer 6 Counter Overflow */ +#define TOVF_ERR7 0x00800000 /* Timer 7 Counter Overflow */ +#define TRUN4 0x10000000 /* Timer 4 Slave Enable Status */ +#define TRUN5 0x20000000 /* Timer 5 Slave Enable Status */ +#define TRUN6 0x40000000 /* Timer 6 Slave Enable Status */ +#define TRUN7 0x80000000 /* Timer 7 Slave Enable Status */ + +/* Alternate Deprecated Macros Provided For Backwards Code Compatibility */ +#define TOVL_ERR0 TOVF_ERR0 +#define TOVL_ERR1 TOVF_ERR1 +#define TOVL_ERR2 TOVF_ERR2 +#define TOVL_ERR3 TOVF_ERR3 +#define TOVL_ERR4 TOVF_ERR4 +#define TOVL_ERR5 TOVF_ERR5 +#define TOVL_ERR6 TOVF_ERR6 +#define TOVL_ERR7 TOVF_ERR7 + +/* TIMERx_CONFIG Masks */ +#define PWM_OUT 0x0001 /* Pulse-Width Modulation Output Mode */ +#define WDTH_CAP 0x0002 /* Width Capture Input Mode */ +#define EXT_CLK 0x0003 /* External Clock Mode */ +#define PULSE_HI 0x0004 /* Action Pulse (Positive/Negative*) */ +#define PERIOD_CNT 0x0008 /* Period Count */ +#define IRQ_ENA 0x0010 /* Interrupt Request Enable */ +#define TIN_SEL 0x0020 /* Timer Input Select */ +#define OUT_DIS 0x0040 /* Output Pad Disable */ +#define CLK_SEL 0x0080 /* Timer Clock Select */ +#define TOGGLE_HI 0x0100 /* PWM_OUT PULSE_HI Toggle Mode */ +#define EMU_RUN 0x0200 /* Emulation Behavior Select */ +#define ERR_TYP 0xC000 /* Error Type */ + + +/* ****************** GPIO PORTS F, G, H MASKS ***********************/ +/* General Purpose IO (0xFFC00700 - 0xFFC007FF) Masks */ +/* Port F Masks */ +#define PF0 0x0001 +#define PF1 0x0002 +#define PF2 0x0004 +#define PF3 0x0008 +#define PF4 0x0010 +#define PF5 0x0020 +#define PF6 0x0040 +#define PF7 0x0080 +#define PF8 0x0100 +#define PF9 0x0200 +#define PF10 0x0400 +#define PF11 0x0800 +#define PF12 0x1000 +#define PF13 0x2000 +#define PF14 0x4000 +#define PF15 0x8000 + +/* Port G Masks */ +#define PG0 0x0001 +#define PG1 0x0002 +#define PG2 0x0004 +#define PG3 0x0008 +#define PG4 0x0010 +#define PG5 0x0020 +#define PG6 0x0040 +#define PG7 0x0080 +#define PG8 0x0100 +#define PG9 0x0200 +#define PG10 0x0400 +#define PG11 0x0800 +#define PG12 0x1000 +#define PG13 0x2000 +#define PG14 0x4000 +#define PG15 0x8000 + +/* Port H Masks */ +#define PH0 0x0001 +#define PH1 0x0002 +#define PH2 0x0004 +#define PH3 0x0008 +#define PH4 0x0010 +#define PH5 0x0020 +#define PH6 0x0040 +#define PH7 0x0080 + + +/* ******************* SERIAL PORT MASKS **************************************/ +/* SPORTx_TCR1 Masks */ +#define TSPEN 0x0001 /* Transmit Enable */ +#define ITCLK 0x0002 /* Internal Transmit Clock Select */ +#define DTYPE_NORM 0x0004 /* Data Format Normal */ +#define DTYPE_ULAW 0x0008 /* Compand Using u-Law */ +#define DTYPE_ALAW 0x000C /* Compand Using A-Law */ +#define TLSBIT 0x0010 /* Transmit Bit Order */ +#define ITFS 0x0200 /* Internal Transmit Frame Sync Select */ +#define TFSR 0x0400 /* Transmit Frame Sync Required Select */ +#define DITFS 0x0800 /* Data-Independent Transmit Frame Sync Select */ +#define LTFS 0x1000 /* Low Transmit Frame Sync Select */ +#define LATFS 0x2000 /* Late Transmit Frame Sync Select */ +#define TCKFE 0x4000 /* Clock Falling Edge Select */ + +/* SPORTx_TCR2 Masks and Macro */ +#define SLEN(x) ((x)&0x1F) /* SPORT TX Word Length (2 - 31) */ +#define TXSE 0x0100 /* TX Secondary Enable */ +#define TSFSE 0x0200 /* Transmit Stereo Frame Sync Enable */ +#define TRFST 0x0400 /* Left/Right Order (1 = Right Channel 1st) */ + +/* SPORTx_RCR1 Masks */ +#define RSPEN 0x0001 /* Receive Enable */ +#define IRCLK 0x0002 /* Internal Receive Clock Select */ +#define DTYPE_NORM 0x0004 /* Data Format Normal */ +#define DTYPE_ULAW 0x0008 /* Compand Using u-Law */ +#define DTYPE_ALAW 0x000C /* Compand Using A-Law */ +#define RLSBIT 0x0010 /* Receive Bit Order */ +#define IRFS 0x0200 /* Internal Receive Frame Sync Select */ +#define RFSR 0x0400 /* Receive Frame Sync Required Select */ +#define LRFS 0x1000 /* Low Receive Frame Sync Select */ +#define LARFS 0x2000 /* Late Receive Frame Sync Select */ +#define RCKFE 0x4000 /* Clock Falling Edge Select */ + +/* SPORTx_RCR2 Masks */ +#define SLEN(x) ((x)&0x1F) /* SPORT RX Word Length (2 - 31) */ +#define RXSE 0x0100 /* RX Secondary Enable */ +#define RSFSE 0x0200 /* RX Stereo Frame Sync Enable */ +#define RRFST 0x0400 /* Right-First Data Order */ + +/* SPORTx_STAT Masks */ +#define RXNE 0x0001 /* Receive FIFO Not Empty Status */ +#define RUVF 0x0002 /* Sticky Receive Underflow Status */ +#define ROVF 0x0004 /* Sticky Receive Overflow Status */ +#define TXF 0x0008 /* Transmit FIFO Full Status */ +#define TUVF 0x0010 /* Sticky Transmit Underflow Status */ +#define TOVF 0x0020 /* Sticky Transmit Overflow Status */ +#define TXHRE 0x0040 /* Transmit Hold Register Empty */ + +/* SPORTx_MCMC1 Macros */ +#define SP_WOFF(x) ((x) & 0x3FF) /* Multichannel Window Offset Field */ + +/* Only use WSIZE Macro With Logic OR While Setting Lower Order Bits */ +#define SP_WSIZE(x) (((((x)>>0x3)-1)&0xF) << 0xC) /* Multichannel Window Size = (x/8)-1 */ + +/* SPORTx_MCMC2 Masks */ +#define REC_BYPASS 0x0000 /* Bypass Mode (No Clock Recovery) */ +#define REC_2FROM4 0x0002 /* Recover 2 MHz Clock from 4 MHz Clock */ +#define REC_8FROM16 0x0003 /* Recover 8 MHz Clock from 16 MHz Clock */ +#define MCDTXPE 0x0004 /* Multichannel DMA Transmit Packing */ +#define MCDRXPE 0x0008 /* Multichannel DMA Receive Packing */ +#define MCMEN 0x0010 /* Multichannel Frame Mode Enable */ +#define FSDR 0x0080 /* Multichannel Frame Sync to Data Relationship */ +#define MFD_0 0x0000 /* Multichannel Frame Delay = 0 */ +#define MFD_1 0x1000 /* Multichannel Frame Delay = 1 */ +#define MFD_2 0x2000 /* Multichannel Frame Delay = 2 */ +#define MFD_3 0x3000 /* Multichannel Frame Delay = 3 */ +#define MFD_4 0x4000 /* Multichannel Frame Delay = 4 */ +#define MFD_5 0x5000 /* Multichannel Frame Delay = 5 */ +#define MFD_6 0x6000 /* Multichannel Frame Delay = 6 */ +#define MFD_7 0x7000 /* Multichannel Frame Delay = 7 */ +#define MFD_8 0x8000 /* Multichannel Frame Delay = 8 */ +#define MFD_9 0x9000 /* Multichannel Frame Delay = 9 */ +#define MFD_10 0xA000 /* Multichannel Frame Delay = 10 */ +#define MFD_11 0xB000 /* Multichannel Frame Delay = 11 */ +#define MFD_12 0xC000 /* Multichannel Frame Delay = 12 */ +#define MFD_13 0xD000 /* Multichannel Frame Delay = 13 */ +#define MFD_14 0xE000 /* Multichannel Frame Delay = 14 */ +#define MFD_15 0xF000 /* Multichannel Frame Delay = 15 */ + + +/* ********************* ASYNCHRONOUS MEMORY CONTROLLER MASKS *************************/ +/* EBIU_AMGCTL Masks */ +#define AMCKEN 0x0001 /* Enable CLKOUT */ +#define AMBEN_NONE 0x0000 /* All Banks Disabled */ +#define AMBEN_B0 0x0002 /* Enable Async Memory Bank 0 only */ +#define AMBEN_B0_B1 0x0004 /* Enable Async Memory Banks 0 & 1 only */ +#define AMBEN_B0_B1_B2 0x0006 /* Enable Async Memory Banks 0, 1, and 2 */ +#define AMBEN_ALL 0x0008 /* Enable Async Memory Banks (all) 0, 1, 2, and 3 */ + +/* EBIU_AMBCTL0 Masks */ +#define B0RDYEN 0x00000001 /* Bank 0 (B0) RDY Enable */ +#define B0RDYPOL 0x00000002 /* B0 RDY Active High */ +#define B0TT_1 0x00000004 /* B0 Transition Time (Read to Write) = 1 cycle */ +#define B0TT_2 0x00000008 /* B0 Transition Time (Read to Write) = 2 cycles */ +#define B0TT_3 0x0000000C /* B0 Transition Time (Read to Write) = 3 cycles */ +#define B0TT_4 0x00000000 /* B0 Transition Time (Read to Write) = 4 cycles */ +#define B0ST_1 0x00000010 /* B0 Setup Time (AOE to Read/Write) = 1 cycle */ +#define B0ST_2 0x00000020 /* B0 Setup Time (AOE to Read/Write) = 2 cycles */ +#define B0ST_3 0x00000030 /* B0 Setup Time (AOE to Read/Write) = 3 cycles */ +#define B0ST_4 0x00000000 /* B0 Setup Time (AOE to Read/Write) = 4 cycles */ +#define B0HT_1 0x00000040 /* B0 Hold Time (~Read/Write to ~AOE) = 1 cycle */ +#define B0HT_2 0x00000080 /* B0 Hold Time (~Read/Write to ~AOE) = 2 cycles */ +#define B0HT_3 0x000000C0 /* B0 Hold Time (~Read/Write to ~AOE) = 3 cycles */ +#define B0HT_0 0x00000000 /* B0 Hold Time (~Read/Write to ~AOE) = 0 cycles */ +#define B0RAT_1 0x00000100 /* B0 Read Access Time = 1 cycle */ +#define B0RAT_2 0x00000200 /* B0 Read Access Time = 2 cycles */ +#define B0RAT_3 0x00000300 /* B0 Read Access Time = 3 cycles */ +#define B0RAT_4 0x00000400 /* B0 Read Access Time = 4 cycles */ +#define B0RAT_5 0x00000500 /* B0 Read Access Time = 5 cycles */ +#define B0RAT_6 0x00000600 /* B0 Read Access Time = 6 cycles */ +#define B0RAT_7 0x00000700 /* B0 Read Access Time = 7 cycles */ +#define B0RAT_8 0x00000800 /* B0 Read Access Time = 8 cycles */ +#define B0RAT_9 0x00000900 /* B0 Read Access Time = 9 cycles */ +#define B0RAT_10 0x00000A00 /* B0 Read Access Time = 10 cycles */ +#define B0RAT_11 0x00000B00 /* B0 Read Access Time = 11 cycles */ +#define B0RAT_12 0x00000C00 /* B0 Read Access Time = 12 cycles */ +#define B0RAT_13 0x00000D00 /* B0 Read Access Time = 13 cycles */ +#define B0RAT_14 0x00000E00 /* B0 Read Access Time = 14 cycles */ +#define B0RAT_15 0x00000F00 /* B0 Read Access Time = 15 cycles */ +#define B0WAT_1 0x00001000 /* B0 Write Access Time = 1 cycle */ +#define B0WAT_2 0x00002000 /* B0 Write Access Time = 2 cycles */ +#define B0WAT_3 0x00003000 /* B0 Write Access Time = 3 cycles */ +#define B0WAT_4 0x00004000 /* B0 Write Access Time = 4 cycles */ +#define B0WAT_5 0x00005000 /* B0 Write Access Time = 5 cycles */ +#define B0WAT_6 0x00006000 /* B0 Write Access Time = 6 cycles */ +#define B0WAT_7 0x00007000 /* B0 Write Access Time = 7 cycles */ +#define B0WAT_8 0x00008000 /* B0 Write Access Time = 8 cycles */ +#define B0WAT_9 0x00009000 /* B0 Write Access Time = 9 cycles */ +#define B0WAT_10 0x0000A000 /* B0 Write Access Time = 10 cycles */ +#define B0WAT_11 0x0000B000 /* B0 Write Access Time = 11 cycles */ +#define B0WAT_12 0x0000C000 /* B0 Write Access Time = 12 cycles */ +#define B0WAT_13 0x0000D000 /* B0 Write Access Time = 13 cycles */ +#define B0WAT_14 0x0000E000 /* B0 Write Access Time = 14 cycles */ +#define B0WAT_15 0x0000F000 /* B0 Write Access Time = 15 cycles */ + +#define B1RDYEN 0x00010000 /* Bank 1 (B1) RDY Enable */ +#define B1RDYPOL 0x00020000 /* B1 RDY Active High */ +#define B1TT_1 0x00040000 /* B1 Transition Time (Read to Write) = 1 cycle */ +#define B1TT_2 0x00080000 /* B1 Transition Time (Read to Write) = 2 cycles */ +#define B1TT_3 0x000C0000 /* B1 Transition Time (Read to Write) = 3 cycles */ +#define B1TT_4 0x00000000 /* B1 Transition Time (Read to Write) = 4 cycles */ +#define B1ST_1 0x00100000 /* B1 Setup Time (AOE to Read/Write) = 1 cycle */ +#define B1ST_2 0x00200000 /* B1 Setup Time (AOE to Read/Write) = 2 cycles */ +#define B1ST_3 0x00300000 /* B1 Setup Time (AOE to Read/Write) = 3 cycles */ +#define B1ST_4 0x00000000 /* B1 Setup Time (AOE to Read/Write) = 4 cycles */ +#define B1HT_1 0x00400000 /* B1 Hold Time (~Read/Write to ~AOE) = 1 cycle */ +#define B1HT_2 0x00800000 /* B1 Hold Time (~Read/Write to ~AOE) = 2 cycles */ +#define B1HT_3 0x00C00000 /* B1 Hold Time (~Read/Write to ~AOE) = 3 cycles */ +#define B1HT_0 0x00000000 /* B1 Hold Time (~Read/Write to ~AOE) = 0 cycles */ +#define B1RAT_1 0x01000000 /* B1 Read Access Time = 1 cycle */ +#define B1RAT_2 0x02000000 /* B1 Read Access Time = 2 cycles */ +#define B1RAT_3 0x03000000 /* B1 Read Access Time = 3 cycles */ +#define B1RAT_4 0x04000000 /* B1 Read Access Time = 4 cycles */ +#define B1RAT_5 0x05000000 /* B1 Read Access Time = 5 cycles */ +#define B1RAT_6 0x06000000 /* B1 Read Access Time = 6 cycles */ +#define B1RAT_7 0x07000000 /* B1 Read Access Time = 7 cycles */ +#define B1RAT_8 0x08000000 /* B1 Read Access Time = 8 cycles */ +#define B1RAT_9 0x09000000 /* B1 Read Access Time = 9 cycles */ +#define B1RAT_10 0x0A000000 /* B1 Read Access Time = 10 cycles */ +#define B1RAT_11 0x0B000000 /* B1 Read Access Time = 11 cycles */ +#define B1RAT_12 0x0C000000 /* B1 Read Access Time = 12 cycles */ +#define B1RAT_13 0x0D000000 /* B1 Read Access Time = 13 cycles */ +#define B1RAT_14 0x0E000000 /* B1 Read Access Time = 14 cycles */ +#define B1RAT_15 0x0F000000 /* B1 Read Access Time = 15 cycles */ +#define B1WAT_1 0x10000000 /* B1 Write Access Time = 1 cycle */ +#define B1WAT_2 0x20000000 /* B1 Write Access Time = 2 cycles */ +#define B1WAT_3 0x30000000 /* B1 Write Access Time = 3 cycles */ +#define B1WAT_4 0x40000000 /* B1 Write Access Time = 4 cycles */ +#define B1WAT_5 0x50000000 /* B1 Write Access Time = 5 cycles */ +#define B1WAT_6 0x60000000 /* B1 Write Access Time = 6 cycles */ +#define B1WAT_7 0x70000000 /* B1 Write Access Time = 7 cycles */ +#define B1WAT_8 0x80000000 /* B1 Write Access Time = 8 cycles */ +#define B1WAT_9 0x90000000 /* B1 Write Access Time = 9 cycles */ +#define B1WAT_10 0xA0000000 /* B1 Write Access Time = 10 cycles */ +#define B1WAT_11 0xB0000000 /* B1 Write Access Time = 11 cycles */ +#define B1WAT_12 0xC0000000 /* B1 Write Access Time = 12 cycles */ +#define B1WAT_13 0xD0000000 /* B1 Write Access Time = 13 cycles */ +#define B1WAT_14 0xE0000000 /* B1 Write Access Time = 14 cycles */ +#define B1WAT_15 0xF0000000 /* B1 Write Access Time = 15 cycles */ + +/* EBIU_AMBCTL1 Masks */ +#define B2RDYEN 0x00000001 /* Bank 2 (B2) RDY Enable */ +#define B2RDYPOL 0x00000002 /* B2 RDY Active High */ +#define B2TT_1 0x00000004 /* B2 Transition Time (Read to Write) = 1 cycle */ +#define B2TT_2 0x00000008 /* B2 Transition Time (Read to Write) = 2 cycles */ +#define B2TT_3 0x0000000C /* B2 Transition Time (Read to Write) = 3 cycles */ +#define B2TT_4 0x00000000 /* B2 Transition Time (Read to Write) = 4 cycles */ +#define B2ST_1 0x00000010 /* B2 Setup Time (AOE to Read/Write) = 1 cycle */ +#define B2ST_2 0x00000020 /* B2 Setup Time (AOE to Read/Write) = 2 cycles */ +#define B2ST_3 0x00000030 /* B2 Setup Time (AOE to Read/Write) = 3 cycles */ +#define B2ST_4 0x00000000 /* B2 Setup Time (AOE to Read/Write) = 4 cycles */ +#define B2HT_1 0x00000040 /* B2 Hold Time (~Read/Write to ~AOE) = 1 cycle */ +#define B2HT_2 0x00000080 /* B2 Hold Time (~Read/Write to ~AOE) = 2 cycles */ +#define B2HT_3 0x000000C0 /* B2 Hold Time (~Read/Write to ~AOE) = 3 cycles */ +#define B2HT_0 0x00000000 /* B2 Hold Time (~Read/Write to ~AOE) = 0 cycles */ +#define B2RAT_1 0x00000100 /* B2 Read Access Time = 1 cycle */ +#define B2RAT_2 0x00000200 /* B2 Read Access Time = 2 cycles */ +#define B2RAT_3 0x00000300 /* B2 Read Access Time = 3 cycles */ +#define B2RAT_4 0x00000400 /* B2 Read Access Time = 4 cycles */ +#define B2RAT_5 0x00000500 /* B2 Read Access Time = 5 cycles */ +#define B2RAT_6 0x00000600 /* B2 Read Access Time = 6 cycles */ +#define B2RAT_7 0x00000700 /* B2 Read Access Time = 7 cycles */ +#define B2RAT_8 0x00000800 /* B2 Read Access Time = 8 cycles */ +#define B2RAT_9 0x00000900 /* B2 Read Access Time = 9 cycles */ +#define B2RAT_10 0x00000A00 /* B2 Read Access Time = 10 cycles */ +#define B2RAT_11 0x00000B00 /* B2 Read Access Time = 11 cycles */ +#define B2RAT_12 0x00000C00 /* B2 Read Access Time = 12 cycles */ +#define B2RAT_13 0x00000D00 /* B2 Read Access Time = 13 cycles */ +#define B2RAT_14 0x00000E00 /* B2 Read Access Time = 14 cycles */ +#define B2RAT_15 0x00000F00 /* B2 Read Access Time = 15 cycles */ +#define B2WAT_1 0x00001000 /* B2 Write Access Time = 1 cycle */ +#define B2WAT_2 0x00002000 /* B2 Write Access Time = 2 cycles */ +#define B2WAT_3 0x00003000 /* B2 Write Access Time = 3 cycles */ +#define B2WAT_4 0x00004000 /* B2 Write Access Time = 4 cycles */ +#define B2WAT_5 0x00005000 /* B2 Write Access Time = 5 cycles */ +#define B2WAT_6 0x00006000 /* B2 Write Access Time = 6 cycles */ +#define B2WAT_7 0x00007000 /* B2 Write Access Time = 7 cycles */ +#define B2WAT_8 0x00008000 /* B2 Write Access Time = 8 cycles */ +#define B2WAT_9 0x00009000 /* B2 Write Access Time = 9 cycles */ +#define B2WAT_10 0x0000A000 /* B2 Write Access Time = 10 cycles */ +#define B2WAT_11 0x0000B000 /* B2 Write Access Time = 11 cycles */ +#define B2WAT_12 0x0000C000 /* B2 Write Access Time = 12 cycles */ +#define B2WAT_13 0x0000D000 /* B2 Write Access Time = 13 cycles */ +#define B2WAT_14 0x0000E000 /* B2 Write Access Time = 14 cycles */ +#define B2WAT_15 0x0000F000 /* B2 Write Access Time = 15 cycles */ + +#define B3RDYEN 0x00010000 /* Bank 3 (B3) RDY Enable */ +#define B3RDYPOL 0x00020000 /* B3 RDY Active High */ +#define B3TT_1 0x00040000 /* B3 Transition Time (Read to Write) = 1 cycle */ +#define B3TT_2 0x00080000 /* B3 Transition Time (Read to Write) = 2 cycles */ +#define B3TT_3 0x000C0000 /* B3 Transition Time (Read to Write) = 3 cycles */ +#define B3TT_4 0x00000000 /* B3 Transition Time (Read to Write) = 4 cycles */ +#define B3ST_1 0x00100000 /* B3 Setup Time (AOE to Read/Write) = 1 cycle */ +#define B3ST_2 0x00200000 /* B3 Setup Time (AOE to Read/Write) = 2 cycles */ +#define B3ST_3 0x00300000 /* B3 Setup Time (AOE to Read/Write) = 3 cycles */ +#define B3ST_4 0x00000000 /* B3 Setup Time (AOE to Read/Write) = 4 cycles */ +#define B3HT_1 0x00400000 /* B3 Hold Time (~Read/Write to ~AOE) = 1 cycle */ +#define B3HT_2 0x00800000 /* B3 Hold Time (~Read/Write to ~AOE) = 2 cycles */ +#define B3HT_3 0x00C00000 /* B3 Hold Time (~Read/Write to ~AOE) = 3 cycles */ +#define B3HT_0 0x00000000 /* B3 Hold Time (~Read/Write to ~AOE) = 0 cycles */ +#define B3RAT_1 0x01000000 /* B3 Read Access Time = 1 cycle */ +#define B3RAT_2 0x02000000 /* B3 Read Access Time = 2 cycles */ +#define B3RAT_3 0x03000000 /* B3 Read Access Time = 3 cycles */ +#define B3RAT_4 0x04000000 /* B3 Read Access Time = 4 cycles */ +#define B3RAT_5 0x05000000 /* B3 Read Access Time = 5 cycles */ +#define B3RAT_6 0x06000000 /* B3 Read Access Time = 6 cycles */ +#define B3RAT_7 0x07000000 /* B3 Read Access Time = 7 cycles */ +#define B3RAT_8 0x08000000 /* B3 Read Access Time = 8 cycles */ +#define B3RAT_9 0x09000000 /* B3 Read Access Time = 9 cycles */ +#define B3RAT_10 0x0A000000 /* B3 Read Access Time = 10 cycles */ +#define B3RAT_11 0x0B000000 /* B3 Read Access Time = 11 cycles */ +#define B3RAT_12 0x0C000000 /* B3 Read Access Time = 12 cycles */ +#define B3RAT_13 0x0D000000 /* B3 Read Access Time = 13 cycles */ +#define B3RAT_14 0x0E000000 /* B3 Read Access Time = 14 cycles */ +#define B3RAT_15 0x0F000000 /* B3 Read Access Time = 15 cycles */ +#define B3WAT_1 0x10000000 /* B3 Write Access Time = 1 cycle */ +#define B3WAT_2 0x20000000 /* B3 Write Access Time = 2 cycles */ +#define B3WAT_3 0x30000000 /* B3 Write Access Time = 3 cycles */ +#define B3WAT_4 0x40000000 /* B3 Write Access Time = 4 cycles */ +#define B3WAT_5 0x50000000 /* B3 Write Access Time = 5 cycles */ +#define B3WAT_6 0x60000000 /* B3 Write Access Time = 6 cycles */ +#define B3WAT_7 0x70000000 /* B3 Write Access Time = 7 cycles */ +#define B3WAT_8 0x80000000 /* B3 Write Access Time = 8 cycles */ +#define B3WAT_9 0x90000000 /* B3 Write Access Time = 9 cycles */ +#define B3WAT_10 0xA0000000 /* B3 Write Access Time = 10 cycles */ +#define B3WAT_11 0xB0000000 /* B3 Write Access Time = 11 cycles */ +#define B3WAT_12 0xC0000000 /* B3 Write Access Time = 12 cycles */ +#define B3WAT_13 0xD0000000 /* B3 Write Access Time = 13 cycles */ +#define B3WAT_14 0xE0000000 /* B3 Write Access Time = 14 cycles */ +#define B3WAT_15 0xF0000000 /* B3 Write Access Time = 15 cycles */ + + +/* ********************** SDRAM CONTROLLER MASKS **********************************************/ +/* EBIU_SDGCTL Masks */ +#define SCTLE 0x00000001 /* Enable SDRAM Signals */ +#define CL_2 0x00000008 /* SDRAM CAS Latency = 2 cycles */ +#define CL_3 0x0000000C /* SDRAM CAS Latency = 3 cycles */ +#define PASR_ALL 0x00000000 /* All 4 SDRAM Banks Refreshed In Self-Refresh */ +#define PASR_B0_B1 0x00000010 /* SDRAM Banks 0 and 1 Are Refreshed In Self-Refresh */ +#define PASR_B0 0x00000020 /* Only SDRAM Bank 0 Is Refreshed In Self-Refresh */ +#define TRAS_1 0x00000040 /* SDRAM tRAS = 1 cycle */ +#define TRAS_2 0x00000080 /* SDRAM tRAS = 2 cycles */ +#define TRAS_3 0x000000C0 /* SDRAM tRAS = 3 cycles */ +#define TRAS_4 0x00000100 /* SDRAM tRAS = 4 cycles */ +#define TRAS_5 0x00000140 /* SDRAM tRAS = 5 cycles */ +#define TRAS_6 0x00000180 /* SDRAM tRAS = 6 cycles */ +#define TRAS_7 0x000001C0 /* SDRAM tRAS = 7 cycles */ +#define TRAS_8 0x00000200 /* SDRAM tRAS = 8 cycles */ +#define TRAS_9 0x00000240 /* SDRAM tRAS = 9 cycles */ +#define TRAS_10 0x00000280 /* SDRAM tRAS = 10 cycles */ +#define TRAS_11 0x000002C0 /* SDRAM tRAS = 11 cycles */ +#define TRAS_12 0x00000300 /* SDRAM tRAS = 12 cycles */ +#define TRAS_13 0x00000340 /* SDRAM tRAS = 13 cycles */ +#define TRAS_14 0x00000380 /* SDRAM tRAS = 14 cycles */ +#define TRAS_15 0x000003C0 /* SDRAM tRAS = 15 cycles */ +#define TRP_1 0x00000800 /* SDRAM tRP = 1 cycle */ +#define TRP_2 0x00001000 /* SDRAM tRP = 2 cycles */ +#define TRP_3 0x00001800 /* SDRAM tRP = 3 cycles */ +#define TRP_4 0x00002000 /* SDRAM tRP = 4 cycles */ +#define TRP_5 0x00002800 /* SDRAM tRP = 5 cycles */ +#define TRP_6 0x00003000 /* SDRAM tRP = 6 cycles */ +#define TRP_7 0x00003800 /* SDRAM tRP = 7 cycles */ +#define TRCD_1 0x00008000 /* SDRAM tRCD = 1 cycle */ +#define TRCD_2 0x00010000 /* SDRAM tRCD = 2 cycles */ +#define TRCD_3 0x00018000 /* SDRAM tRCD = 3 cycles */ +#define TRCD_4 0x00020000 /* SDRAM tRCD = 4 cycles */ +#define TRCD_5 0x00028000 /* SDRAM tRCD = 5 cycles */ +#define TRCD_6 0x00030000 /* SDRAM tRCD = 6 cycles */ +#define TRCD_7 0x00038000 /* SDRAM tRCD = 7 cycles */ +#define TWR_1 0x00080000 /* SDRAM tWR = 1 cycle */ +#define TWR_2 0x00100000 /* SDRAM tWR = 2 cycles */ +#define TWR_3 0x00180000 /* SDRAM tWR = 3 cycles */ +#define PUPSD 0x00200000 /* Power-Up Start Delay (15 SCLK Cycles Delay) */ +#define PSM 0x00400000 /* Power-Up Sequence (Mode Register Before/After* Refresh) */ +#define PSS 0x00800000 /* Enable Power-Up Sequence on Next SDRAM Access */ +#define SRFS 0x01000000 /* Enable SDRAM Self-Refresh Mode */ +#define EBUFE 0x02000000 /* Enable External Buffering Timing */ +#define FBBRW 0x04000000 /* Enable Fast Back-To-Back Read To Write */ +#define EMREN 0x10000000 /* Extended Mode Register Enable */ +#define TCSR 0x20000000 /* Temp-Compensated Self-Refresh Value (85/45* Deg C) */ +#define CDDBG 0x40000000 /* Tristate SDRAM Controls During Bus Grant */ + +/* EBIU_SDBCTL Masks */ +#define EBE 0x0001 /* Enable SDRAM External Bank */ +#define EBSZ_16 0x0000 /* SDRAM External Bank Size = 16MB */ +#define EBSZ_32 0x0002 /* SDRAM External Bank Size = 32MB */ +#define EBSZ_64 0x0004 /* SDRAM External Bank Size = 64MB */ +#define EBSZ_128 0x0006 /* SDRAM External Bank Size = 128MB */ +#define EBSZ_256 0x0008 /* SDRAM External Bank Size = 256MB */ +#define EBSZ_512 0x000A /* SDRAM External Bank Size = 512MB */ +#define EBCAW_8 0x0000 /* SDRAM External Bank Column Address Width = 8 Bits */ +#define EBCAW_9 0x0010 /* SDRAM External Bank Column Address Width = 9 Bits */ +#define EBCAW_10 0x0020 /* SDRAM External Bank Column Address Width = 10 Bits */ +#define EBCAW_11 0x0030 /* SDRAM External Bank Column Address Width = 11 Bits */ + +/* EBIU_SDSTAT Masks */ +#define SDCI 0x0001 /* SDRAM Controller Idle */ +#define SDSRA 0x0002 /* SDRAM Self-Refresh Active */ +#define SDPUA 0x0004 /* SDRAM Power-Up Active */ +#define SDRS 0x0008 /* SDRAM Will Power-Up On Next Access */ +#define SDEASE 0x0010 /* SDRAM EAB Sticky Error Status */ +#define BGSTAT 0x0020 /* Bus Grant Status */ + + +/* ************************** DMA CONTROLLER MASKS ********************************/ +/* DMAx_CONFIG, MDMA_yy_CONFIG Masks */ +#define DMAEN 0x0001 /* DMA Channel Enable */ +#define WNR 0x0002 /* Channel Direction (W/R*) */ +#define WDSIZE_8 0x0000 /* Transfer Word Size = 8 */ +#define WDSIZE_16 0x0004 /* Transfer Word Size = 16 */ +#define WDSIZE_32 0x0008 /* Transfer Word Size = 32 */ +#define DMA2D 0x0010 /* DMA Mode (2D/1D*) */ +#define RESTART 0x0020 /* DMA Buffer Clear */ +#define DI_SEL 0x0040 /* Data Interrupt Timing Select */ +#define DI_EN 0x0080 /* Data Interrupt Enable */ +#define NDSIZE_0 0x0000 /* Next Descriptor Size = 0 (Stop/Autobuffer) */ +#define NDSIZE_1 0x0100 /* Next Descriptor Size = 1 */ +#define NDSIZE_2 0x0200 /* Next Descriptor Size = 2 */ +#define NDSIZE_3 0x0300 /* Next Descriptor Size = 3 */ +#define NDSIZE_4 0x0400 /* Next Descriptor Size = 4 */ +#define NDSIZE_5 0x0500 /* Next Descriptor Size = 5 */ +#define NDSIZE_6 0x0600 /* Next Descriptor Size = 6 */ +#define NDSIZE_7 0x0700 /* Next Descriptor Size = 7 */ +#define NDSIZE_8 0x0800 /* Next Descriptor Size = 8 */ +#define NDSIZE_9 0x0900 /* Next Descriptor Size = 9 */ +#define NDSIZE 0x0900 /* Next Descriptor Size */ +#define DMAFLOW 0x7000 /* Flow Control */ +#define DMAFLOW_STOP 0x0000 /* Stop Mode */ +#define DMAFLOW_AUTO 0x1000 /* Autobuffer Mode */ +#define DMAFLOW_ARRAY 0x4000 /* Descriptor Array Mode */ +#define DMAFLOW_SMALL 0x6000 /* Small Model Descriptor List Mode */ +#define DMAFLOW_LARGE 0x7000 /* Large Model Descriptor List Mode */ + +/* DMAx_PERIPHERAL_MAP, MDMA_yy_PERIPHERAL_MAP Masks */ +#define CTYPE 0x0040 /* DMA Channel Type Indicator (Memory/Peripheral*) */ +#define PMAP 0xF000 /* Peripheral Mapped To This Channel */ +#define PMAP_PPI 0x0000 /* PPI Port DMA */ +#define PMAP_EMACRX 0x1000 /* Ethernet Receive DMA */ +#define PMAP_EMACTX 0x2000 /* Ethernet Transmit DMA */ +#define PMAP_SPORT0RX 0x3000 /* SPORT0 Receive DMA */ +#define PMAP_SPORT0TX 0x4000 /* SPORT0 Transmit DMA */ +#define PMAP_SPORT1RX 0x5000 /* SPORT1 Receive DMA */ +#define PMAP_SPORT1TX 0x6000 /* SPORT1 Transmit DMA */ +#define PMAP_SPI 0x7000 /* SPI Port DMA */ +#define PMAP_UART0RX 0x8000 /* UART0 Port Receive DMA */ +#define PMAP_UART0TX 0x9000 /* UART0 Port Transmit DMA */ +#define PMAP_UART1RX 0xA000 /* UART1 Port Receive DMA */ +#define PMAP_UART1TX 0xB000 /* UART1 Port Transmit DMA */ + +/* DMAx_IRQ_STATUS, MDMA_yy_IRQ_STATUS Masks */ +#define DMA_DONE 0x0001 /* DMA Completion Interrupt Status */ +#define DMA_ERR 0x0002 /* DMA Error Interrupt Status */ +#define DFETCH 0x0004 /* DMA Descriptor Fetch Indicator */ +#define DMA_RUN 0x0008 /* DMA Channel Running Indicator */ + + +/* ************ PARALLEL PERIPHERAL INTERFACE (PPI) MASKS *************/ +/* PPI_CONTROL Masks */ +#define PORT_EN 0x0001 /* PPI Port Enable */ +#define PORT_DIR 0x0002 /* PPI Port Direction */ +#define XFR_TYPE 0x000C /* PPI Transfer Type */ +#define PORT_CFG 0x0030 /* PPI Port Configuration */ +#define FLD_SEL 0x0040 /* PPI Active Field Select */ +#define PACK_EN 0x0080 /* PPI Packing Mode */ +#define DMA32 0x0100 /* PPI 32-bit DMA Enable */ +#define SKIP_EN 0x0200 /* PPI Skip Element Enable */ +#define SKIP_EO 0x0400 /* PPI Skip Even/Odd Elements */ +#define DLEN_8 0x0000 /* Data Length = 8 Bits */ +#define DLEN_10 0x0800 /* Data Length = 10 Bits */ +#define DLEN_11 0x1000 /* Data Length = 11 Bits */ +#define DLEN_12 0x1800 /* Data Length = 12 Bits */ +#define DLEN_13 0x2000 /* Data Length = 13 Bits */ +#define DLEN_14 0x2800 /* Data Length = 14 Bits */ +#define DLEN_15 0x3000 /* Data Length = 15 Bits */ +#define DLEN_16 0x3800 /* Data Length = 16 Bits */ +#define DLENGTH 0x3800 /* PPI Data Length */ +#define POLC 0x4000 /* PPI Clock Polarity */ +#define POLS 0x8000 /* PPI Frame Sync Polarity */ + +/* PPI_STATUS Masks */ +#define FLD 0x0400 /* Field Indicator */ +#define FT_ERR 0x0800 /* Frame Track Error */ +#define OVR 0x1000 /* FIFO Overflow Error */ +#define UNDR 0x2000 /* FIFO Underrun Error */ +#define ERR_DET 0x4000 /* Error Detected Indicator */ +#define ERR_NCOR 0x8000 /* Error Not Corrected Indicator */ + + +/* ******************** TWO-WIRE INTERFACE (TWI) MASKS ***********************/ +/* TWI_CLKDIV Macros (Use: *pTWI_CLKDIV = CLKLOW(x)|CLKHI(y); ) */ +#define CLKLOW(x) ((x) & 0xFF) /* Periods Clock Is Held Low */ +#define CLKHI(y) (((y)&0xFF)<<0x8) /* Periods Before New Clock Low */ + +/* TWI_PRESCALE Masks */ +#define PRESCALE 0x007F /* SCLKs Per Internal Time Reference (10MHz) */ +#define TWI_ENA 0x0080 /* TWI Enable */ +#define SCCB 0x0200 /* SCCB Compatibility Enable */ + +/* TWI_SLAVE_CTRL Masks */ +#define SEN 0x0001 /* Slave Enable */ +#define SADD_LEN 0x0002 /* Slave Address Length */ +#define STDVAL 0x0004 /* Slave Transmit Data Valid */ +#define NAK 0x0008 /* NAK/ACK* Generated At Conclusion Of Transfer */ +#define GEN 0x0010 /* General Call Adrress Matching Enabled */ + +/* TWI_SLAVE_STAT Masks */ +#define SDIR 0x0001 /* Slave Transfer Direction (Transmit/Receive*) */ +#define GCALL 0x0002 /* General Call Indicator */ + +/* TWI_MASTER_CTRL Masks */ +#define MEN 0x0001 /* Master Mode Enable */ +#define MADD_LEN 0x0002 /* Master Address Length */ +#define MDIR 0x0004 /* Master Transmit Direction (RX/TX*) */ +#define FAST 0x0008 /* Use Fast Mode Timing Specs */ +#define STOP 0x0010 /* Issue Stop Condition */ +#define RSTART 0x0020 /* Repeat Start or Stop* At End Of Transfer */ +#define DCNT 0x3FC0 /* Data Bytes To Transfer */ +#define SDAOVR 0x4000 /* Serial Data Override */ +#define SCLOVR 0x8000 /* Serial Clock Override */ + +/* TWI_MASTER_STAT Masks */ +#define MPROG 0x0001 /* Master Transfer In Progress */ +#define LOSTARB 0x0002 /* Lost Arbitration Indicator (Xfer Aborted) */ +#define ANAK 0x0004 /* Address Not Acknowledged */ +#define DNAK 0x0008 /* Data Not Acknowledged */ +#define BUFRDERR 0x0010 /* Buffer Read Error */ +#define BUFWRERR 0x0020 /* Buffer Write Error */ +#define SDASEN 0x0040 /* Serial Data Sense */ +#define SCLSEN 0x0080 /* Serial Clock Sense */ +#define BUSBUSY 0x0100 /* Bus Busy Indicator */ + +/* TWI_INT_SRC and TWI_INT_ENABLE Masks */ +#define SINIT 0x0001 /* Slave Transfer Initiated */ +#define SCOMP 0x0002 /* Slave Transfer Complete */ +#define SERR 0x0004 /* Slave Transfer Error */ +#define SOVF 0x0008 /* Slave Overflow */ +#define MCOMP 0x0010 /* Master Transfer Complete */ +#define MERR 0x0020 /* Master Transfer Error */ +#define XMTSERV 0x0040 /* Transmit FIFO Service */ +#define RCVSERV 0x0080 /* Receive FIFO Service */ + +/* TWI_FIFO_CTRL Masks */ +#define XMTFLUSH 0x0001 /* Transmit Buffer Flush */ +#define RCVFLUSH 0x0002 /* Receive Buffer Flush */ +#define XMTINTLEN 0x0004 /* Transmit Buffer Interrupt Length */ +#define RCVINTLEN 0x0008 /* Receive Buffer Interrupt Length */ + +/* TWI_FIFO_STAT Masks */ +#define XMTSTAT 0x0003 /* Transmit FIFO Status */ +#define XMT_EMPTY 0x0000 /* Transmit FIFO Empty */ +#define XMT_HALF 0x0001 /* Transmit FIFO Has 1 Byte To Write */ +#define XMT_FULL 0x0003 /* Transmit FIFO Full (2 Bytes To Write) */ + +#define RCVSTAT 0x000C /* Receive FIFO Status */ +#define RCV_EMPTY 0x0000 /* Receive FIFO Empty */ +#define RCV_HALF 0x0004 /* Receive FIFO Has 1 Byte To Read */ +#define RCV_FULL 0x000C /* Receive FIFO Full (2 Bytes To Read) */ + + +/* ******************* PIN CONTROL REGISTER MASKS ************************/ +/* PORT_MUX Masks */ +#define PJSE 0x0001 /* Port J SPI/SPORT Enable */ +#define PJSE_SPORT 0x0000 /* Enable TFS0/DT0PRI */ +#define PJSE_SPI 0x0001 /* Enable SPI_SSEL3:2 */ + +#define PJCE(x) (((x)&0x3)<<1) /* Port J CAN/SPI/SPORT Enable */ +#define PJCE_SPORT 0x0000 /* Enable DR0SEC/DT0SEC */ +#define PJCE_CAN 0x0002 /* Enable CAN RX/TX */ +#define PJCE_SPI 0x0004 /* Enable SPI_SSEL7 */ + +#define PFDE 0x0008 /* Port F DMA Request Enable */ +#define PFDE_UART 0x0000 /* Enable UART0 RX/TX */ +#define PFDE_DMA 0x0008 /* Enable DMAR1:0 */ + +#define PFTE 0x0010 /* Port F Timer Enable */ +#define PFTE_UART 0x0000 /* Enable UART1 RX/TX */ +#define PFTE_TIMER 0x0010 /* Enable TMR7:6 */ + +#define PFS6E 0x0020 /* Port F SPI SSEL 6 Enable */ +#define PFS6E_TIMER 0x0000 /* Enable TMR5 */ +#define PFS6E_SPI 0x0020 /* Enable SPI_SSEL6 */ + +#define PFS5E 0x0040 /* Port F SPI SSEL 5 Enable */ +#define PFS5E_TIMER 0x0000 /* Enable TMR4 */ +#define PFS5E_SPI 0x0040 /* Enable SPI_SSEL5 */ + +#define PFS4E 0x0080 /* Port F SPI SSEL 4 Enable */ +#define PFS4E_TIMER 0x0000 /* Enable TMR3 */ +#define PFS4E_SPI 0x0080 /* Enable SPI_SSEL4 */ + +#define PFFE 0x0100 /* Port F PPI Frame Sync Enable */ +#define PFFE_TIMER 0x0000 /* Enable TMR2 */ +#define PFFE_PPI 0x0100 /* Enable PPI FS3 */ + +#define PGSE 0x0200 /* Port G SPORT1 Secondary Enable */ +#define PGSE_PPI 0x0000 /* Enable PPI D9:8 */ +#define PGSE_SPORT 0x0200 /* Enable DR1SEC/DT1SEC */ + +#define PGRE 0x0400 /* Port G SPORT1 Receive Enable */ +#define PGRE_PPI 0x0000 /* Enable PPI D12:10 */ +#define PGRE_SPORT 0x0400 /* Enable DR1PRI/RFS1/RSCLK1 */ + +#define PGTE 0x0800 /* Port G SPORT1 Transmit Enable */ +#define PGTE_PPI 0x0000 /* Enable PPI D15:13 */ +#define PGTE_SPORT 0x0800 /* Enable DT1PRI/TFS1/TSCLK1 */ + + +/* ****************** HANDSHAKE DMA (HDMA) MASKS *********************/ +/* HDMAx_CTL Masks */ +#define HMDMAEN 0x0001 /* Enable Handshake DMA 0/1 */ +#define REP 0x0002 /* HDMA Request Polarity */ +#define UTE 0x0004 /* Urgency Threshold Enable */ +#define OIE 0x0010 /* Overflow Interrupt Enable */ +#define BDIE 0x0020 /* Block Done Interrupt Enable */ +#define MBDI 0x0040 /* Mask Block Done IRQ If Pending ECNT */ +#define DRQ 0x0300 /* HDMA Request Type */ +#define DRQ_NONE 0x0000 /* No Request */ +#define DRQ_SINGLE 0x0100 /* Channels Request Single */ +#define DRQ_MULTI 0x0200 /* Channels Request Multi (Default) */ +#define DRQ_URGENT 0x0300 /* Channels Request Multi Urgent */ +#define RBC 0x1000 /* Reload BCNT With IBCNT */ +#define PS 0x2000 /* HDMA Pin Status */ +#define OI 0x4000 /* Overflow Interrupt Generated */ +#define BDI 0x8000 /* Block Done Interrupt Generated */ + +/* entry addresses of the user-callable Boot ROM functions */ + +#define _BOOTROM_RESET 0xEF000000 +#define _BOOTROM_FINAL_INIT 0xEF000002 +#define _BOOTROM_DO_MEMORY_DMA 0xEF000006 +#define _BOOTROM_BOOT_DXE_FLASH 0xEF000008 +#define _BOOTROM_BOOT_DXE_SPI 0xEF00000A +#define _BOOTROM_BOOT_DXE_TWI 0xEF00000C +#define _BOOTROM_GET_DXE_ADDRESS_FLASH 0xEF000010 +#define _BOOTROM_GET_DXE_ADDRESS_SPI 0xEF000012 +#define _BOOTROM_GET_DXE_ADDRESS_TWI 0xEF000014 + +/* Alternate Deprecated Macros Provided For Backwards Code Compatibility */ +#define PGDE_UART PFDE_UART +#define PGDE_DMA PFDE_DMA +#define CKELOW SCKELOW + +/* HOST Port Registers */ + +#define HOST_CONTROL 0xffc03400 /* HOST Control Register */ +#define HOST_STATUS 0xffc03404 /* HOST Status Register */ +#define HOST_TIMEOUT 0xffc03408 /* HOST Acknowledge Mode Timeout Register */ + +/* Counter Registers */ + +#define CNT_CONFIG 0xffc03500 /* Configuration Register */ +#define CNT_IMASK 0xffc03504 /* Interrupt Mask Register */ +#define CNT_STATUS 0xffc03508 /* Status Register */ +#define CNT_COMMAND 0xffc0350c /* Command Register */ +#define CNT_DEBOUNCE 0xffc03510 /* Debounce Register */ +#define CNT_COUNTER 0xffc03514 /* Counter Register */ +#define CNT_MAX 0xffc03518 /* Maximal Count Register */ +#define CNT_MIN 0xffc0351c /* Minimal Count Register */ + +/* OTP/FUSE Registers */ + +#define OTP_CONTROL 0xffc03600 /* OTP/Fuse Control Register */ +#define OTP_BEN 0xffc03604 /* OTP/Fuse Byte Enable */ +#define OTP_STATUS 0xffc03608 /* OTP/Fuse Status */ +#define OTP_TIMING 0xffc0360c /* OTP/Fuse Access Timing */ + +/* Security Registers */ + +#define SECURE_SYSSWT 0xffc03620 /* Secure System Switches */ +#define SECURE_CONTROL 0xffc03624 /* Secure Control */ +#define SECURE_STATUS 0xffc03628 /* Secure Status */ + +/* OTP Read/Write Data Buffer Registers */ + +#define OTP_DATA0 0xffc03680 /* OTP/Fuse Data (OTP_DATA0-3) accesses the fuse read write buffer */ +#define OTP_DATA1 0xffc03684 /* OTP/Fuse Data (OTP_DATA0-3) accesses the fuse read write buffer */ +#define OTP_DATA2 0xffc03688 /* OTP/Fuse Data (OTP_DATA0-3) accesses the fuse read write buffer */ +#define OTP_DATA3 0xffc0368c /* OTP/Fuse Data (OTP_DATA0-3) accesses the fuse read write buffer */ + +/* Motor Control PWM Registers */ + +#define PWM_CTRL 0xffc03700 /* PWM Control Register */ +#define PWM_STAT 0xffc03704 /* PWM Status Register */ +#define PWM_TM 0xffc03708 /* PWM Period Register */ +#define PWM_DT 0xffc0370c /* PWM Dead Time Register */ +#define PWM_GATE 0xffc03710 /* PWM Chopping Control */ +#define PWM_CHA 0xffc03714 /* PWM Channel A Duty Control */ +#define PWM_CHB 0xffc03718 /* PWM Channel B Duty Control */ +#define PWM_CHC 0xffc0371c /* PWM Channel C Duty Control */ +#define PWM_SEG 0xffc03720 /* PWM Crossover and Output Enable */ +#define PWM_SYNCWT 0xffc03724 /* PWM Sync Pluse Width Control */ +#define PWM_CHAL 0xffc03728 /* PWM Channel AL Duty Control (SR mode only) */ +#define PWM_CHBL 0xffc0372c /* PWM Channel BL Duty Control (SR mode only) */ +#define PWM_CHCL 0xffc03730 /* PWM Channel CL Duty Control (SR mode only) */ +#define PWM_LSI 0xffc03734 /* PWM Low Side Invert (SR mode only) */ +#define PWM_STAT2 0xffc03738 /* PWM Status Register 2 */ + + +/* ********************************************************** */ +/* SINGLE BIT MACRO PAIRS (bit mask and negated one) */ +/* and MULTI BIT READ MACROS */ +/* ********************************************************** */ + +/* Bit masks for HOST_CONTROL */ + +#define HOST_CNTR_HOST_EN 0x1 /* Host Enable */ +#define HOST_CNTR_nHOST_EN 0x0 +#define HOST_CNTR_HOST_END 0x2 /* Host Endianess */ +#define HOST_CNTR_nHOST_END 0x0 +#define HOST_CNTR_DATA_SIZE 0x4 /* Data Size */ +#define HOST_CNTR_nDATA_SIZE 0x0 +#define HOST_CNTR_HOST_RST 0x8 /* Host Reset */ +#define HOST_CNTR_nHOST_RST 0x0 +#define HOST_CNTR_HRDY_OVR 0x20 /* Host Ready Override */ +#define HOST_CNTR_nHRDY_OVR 0x0 +#define HOST_CNTR_INT_MODE 0x40 /* Interrupt Mode */ +#define HOST_CNTR_nINT_MODE 0x0 +#define HOST_CNTR_BT_EN 0x80 /* Bus Timeout Enable */ +#define HOST_CNTR_ nBT_EN 0x0 +#define HOST_CNTR_EHW 0x100 /* Enable Host Write */ +#define HOST_CNTR_nEHW 0x0 +#define HOST_CNTR_EHR 0x200 /* Enable Host Read */ +#define HOST_CNTR_nEHR 0x0 +#define HOST_CNTR_BDR 0x400 /* Burst DMA Requests */ +#define HOST_CNTR_nBDR 0x0 + +/* Bit masks for HOST_STATUS */ + +#define HOST_STAT_READY 0x1 /* DMA Ready */ +#define HOST_STAT_nREADY 0x0 +#define HOST_STAT_FIFOFULL 0x2 /* FIFO Full */ +#define HOST_STAT_nFIFOFULL 0x0 +#define HOST_STAT_FIFOEMPTY 0x4 /* FIFO Empty */ +#define HOST_STAT_nFIFOEMPTY 0x0 +#define HOST_STAT_COMPLETE 0x8 /* DMA Complete */ +#define HOST_STAT_nCOMPLETE 0x0 +#define HOST_STAT_HSHK 0x10 /* Host Handshake */ +#define HOST_STAT_nHSHK 0x0 +#define HOST_STAT_TIMEOUT 0x20 /* Host Timeout */ +#define HOST_STAT_nTIMEOUT 0x0 +#define HOST_STAT_HIRQ 0x40 /* Host Interrupt Request */ +#define HOST_STAT_nHIRQ 0x0 +#define HOST_STAT_ALLOW_CNFG 0x80 /* Allow New Configuration */ +#define HOST_STAT_nALLOW_CNFG 0x0 +#define HOST_STAT_DMA_DIR 0x100 /* DMA Direction */ +#define HOST_STAT_nDMA_DIR 0x0 +#define HOST_STAT_BTE 0x200 /* Bus Timeout Enabled */ +#define HOST_STAT_nBTE 0x0 +#define HOST_STAT_HOSTRD_DONE 0x8000 /* Host Read Completion Interrupt */ +#define HOST_STAT_nHOSTRD_DONE 0x0 + +/* Bit masks for HOST_TIMEOUT */ + +#define HOST_COUNT_TIMEOUT 0x7ff /* Host Timeout count */ + +/* Bit masks for CNT_CONFIG */ + +#define CNTE 0x1 /* Counter Enable */ +#define nCNTE 0x0 +#define DEBE 0x2 /* Debounce Enable */ +#define nDEBE 0x0 +#define CDGINV 0x10 /* CDG Pin Polarity Invert */ +#define nCDGINV 0x0 +#define CUDINV 0x20 /* CUD Pin Polarity Invert */ +#define nCUDINV 0x0 +#define CZMINV 0x40 /* CZM Pin Polarity Invert */ +#define nCZMINV 0x0 +#define CNTMODE 0x700 /* Counter Operating Mode */ +#define ZMZC 0x800 /* CZM Zeroes Counter Enable */ +#define nZMZC 0x0 +#define BNDMODE 0x3000 /* Boundary register Mode */ +#define INPDIS 0x8000 /* CUG and CDG Input Disable */ +#define nINPDIS 0x0 + +/* Bit masks for CNT_IMASK */ + +#define ICIE 0x1 /* Illegal Gray/Binary Code Interrupt Enable */ +#define nICIE 0x0 +#define UCIE 0x2 /* Up count Interrupt Enable */ +#define nUCIE 0x0 +#define DCIE 0x4 /* Down count Interrupt Enable */ +#define nDCIE 0x0 +#define MINCIE 0x8 /* Min Count Interrupt Enable */ +#define nMINCIE 0x0 +#define MAXCIE 0x10 /* Max Count Interrupt Enable */ +#define nMAXCIE 0x0 +#define COV31IE 0x20 /* Bit 31 Overflow Interrupt Enable */ +#define nCOV31IE 0x0 +#define COV15IE 0x40 /* Bit 15 Overflow Interrupt Enable */ +#define nCOV15IE 0x0 +#define CZEROIE 0x80 /* Count to Zero Interrupt Enable */ +#define nCZEROIE 0x0 +#define CZMIE 0x100 /* CZM Pin Interrupt Enable */ +#define nCZMIE 0x0 +#define CZMEIE 0x200 /* CZM Error Interrupt Enable */ +#define nCZMEIE 0x0 +#define CZMZIE 0x400 /* CZM Zeroes Counter Interrupt Enable */ +#define nCZMZIE 0x0 + +/* Bit masks for CNT_STATUS */ + +#define ICII 0x1 /* Illegal Gray/Binary Code Interrupt Identifier */ +#define nICII 0x0 +#define UCII 0x2 /* Up count Interrupt Identifier */ +#define nUCII 0x0 +#define DCII 0x4 /* Down count Interrupt Identifier */ +#define nDCII 0x0 +#define MINCII 0x8 /* Min Count Interrupt Identifier */ +#define nMINCII 0x0 +#define MAXCII 0x10 /* Max Count Interrupt Identifier */ +#define nMAXCII 0x0 +#define COV31II 0x20 /* Bit 31 Overflow Interrupt Identifier */ +#define nCOV31II 0x0 +#define COV15II 0x40 /* Bit 15 Overflow Interrupt Identifier */ +#define nCOV15II 0x0 +#define CZEROII 0x80 /* Count to Zero Interrupt Identifier */ +#define nCZEROII 0x0 +#define CZMII 0x100 /* CZM Pin Interrupt Identifier */ +#define nCZMII 0x0 +#define CZMEII 0x200 /* CZM Error Interrupt Identifier */ +#define nCZMEII 0x0 +#define CZMZII 0x400 /* CZM Zeroes Counter Interrupt Identifier */ +#define nCZMZII 0x0 + +/* Bit masks for CNT_COMMAND */ + +#define W1LCNT 0xf /* Load Counter Register */ +#define W1LMIN 0xf0 /* Load Min Register */ +#define W1LMAX 0xf00 /* Load Max Register */ +#define W1ZMONCE 0x1000 /* Enable CZM Clear Counter Once */ +#define nW1ZMONCE 0x0 + +/* Bit masks for CNT_DEBOUNCE */ + +#define DPRESCALE 0xf /* Load Counter Register */ + +/* CNT_COMMAND bit field options */ + +#define W1LCNT_ZERO 0x0001 /* write 1 to load CNT_COUNTER with zero */ +#define W1LCNT_MIN 0x0004 /* write 1 to load CNT_COUNTER from CNT_MIN */ +#define W1LCNT_MAX 0x0008 /* write 1 to load CNT_COUNTER from CNT_MAX */ + +#define W1LMIN_ZERO 0x0010 /* write 1 to load CNT_MIN with zero */ +#define W1LMIN_CNT 0x0020 /* write 1 to load CNT_MIN from CNT_COUNTER */ +#define W1LMIN_MAX 0x0080 /* write 1 to load CNT_MIN from CNT_MAX */ + +#define W1LMAX_ZERO 0x0100 /* write 1 to load CNT_MAX with zero */ +#define W1LMAX_CNT 0x0200 /* write 1 to load CNT_MAX from CNT_COUNTER */ +#define W1LMAX_MIN 0x0400 /* write 1 to load CNT_MAX from CNT_MIN */ + +/* CNT_CONFIG bit field options */ + +#define CNTMODE_QUADENC 0x0000 /* quadrature encoder mode */ +#define CNTMODE_BINENC 0x0100 /* binary encoder mode */ +#define CNTMODE_UDCNT 0x0200 /* up/down counter mode */ +#define CNTMODE_DIRCNT 0x0400 /* direction counter mode */ +#define CNTMODE_DIRTMR 0x0500 /* direction timer mode */ + +#define BNDMODE_COMP 0x0000 /* boundary compare mode */ +#define BNDMODE_ZERO 0x1000 /* boundary compare and zero mode */ +#define BNDMODE_CAPT 0x2000 /* boundary capture mode */ +#define BNDMODE_AEXT 0x3000 /* boundary auto-extend mode */ + +/* Bit masks for OTP_CONTROL */ + +#define FUSE_FADDR 0x1ff /* OTP/Fuse Address */ +#define FIEN 0x800 /* OTP/Fuse Interrupt Enable */ +#define nFIEN 0x0 +#define FTESTDEC 0x1000 /* OTP/Fuse Test Decoder */ +#define nFTESTDEC 0x0 +#define FWRTEST 0x2000 /* OTP/Fuse Write Test */ +#define nFWRTEST 0x0 +#define FRDEN 0x4000 /* OTP/Fuse Read Enable */ +#define nFRDEN 0x0 +#define FWREN 0x8000 /* OTP/Fuse Write Enable */ +#define nFWREN 0x0 + +/* Bit masks for OTP_BEN */ + +#define FBEN 0xffff /* OTP/Fuse Byte Enable */ + +/* Bit masks for OTP_STATUS */ + +#define FCOMP 0x1 /* OTP/Fuse Access Complete */ +#define nFCOMP 0x0 +#define FERROR 0x2 /* OTP/Fuse Access Error */ +#define nFERROR 0x0 +#define MMRGLOAD 0x10 /* Memory Mapped Register Gasket Load */ +#define nMMRGLOAD 0x0 +#define MMRGLOCK 0x20 /* Memory Mapped Register Gasket Lock */ +#define nMMRGLOCK 0x0 +#define FPGMEN 0x40 /* OTP/Fuse Program Enable */ +#define nFPGMEN 0x0 + +/* Bit masks for OTP_TIMING */ + +#define USECDIV 0xff /* Micro Second Divider */ +#define READACC 0x7f00 /* Read Access Time */ +#define CPUMPRL 0x38000 /* Charge Pump Release Time */ +#define CPUMPSU 0xc0000 /* Charge Pump Setup Time */ +#define CPUMPHD 0xf00000 /* Charge Pump Hold Time */ +#define PGMTIME 0xff000000 /* Program Time */ + +/* Bit masks for SECURE_SYSSWT */ + +#define EMUDABL 0x1 /* Emulation Disable. */ +#define nEMUDABL 0x0 +#define RSTDABL 0x2 /* Reset Disable */ +#define nRSTDABL 0x0 +#define L1IDABL 0x1c /* L1 Instruction Memory Disable. */ +#define L1DADABL 0xe0 /* L1 Data Bank A Memory Disable. */ +#define L1DBDABL 0x700 /* L1 Data Bank B Memory Disable. */ +#define DMA0OVR 0x800 /* DMA0 Memory Access Override */ +#define nDMA0OVR 0x0 +#define DMA1OVR 0x1000 /* DMA1 Memory Access Override */ +#define nDMA1OVR 0x0 +#define EMUOVR 0x4000 /* Emulation Override */ +#define nEMUOVR 0x0 +#define OTPSEN 0x8000 /* OTP Secrets Enable. */ +#define nOTPSEN 0x0 +#define L2DABL 0x70000 /* L2 Memory Disable. */ + +/* Bit masks for SECURE_CONTROL */ + +#define SECURE0 0x1 /* SECURE 0 */ +#define nSECURE0 0x0 +#define SECURE1 0x2 /* SECURE 1 */ +#define nSECURE1 0x0 +#define SECURE2 0x4 /* SECURE 2 */ +#define nSECURE2 0x0 +#define SECURE3 0x8 /* SECURE 3 */ +#define nSECURE3 0x0 + +/* Bit masks for SECURE_STATUS */ + +#define SECMODE 0x3 /* Secured Mode Control State */ +#define NMI 0x4 /* Non Maskable Interrupt */ +#define nNMI 0x0 +#define AFVALID 0x8 /* Authentication Firmware Valid */ +#define nAFVALID 0x0 +#define AFEXIT 0x10 /* Authentication Firmware Exit */ +#define nAFEXIT 0x0 +#define SECSTAT 0xe0 /* Secure Status */ + + + +#endif /* _DEF_BF51X_H */ diff --git a/arch/blackfin/mach-bf518/include/mach/dma.h b/arch/blackfin/mach-bf518/include/mach/dma.h new file mode 100644 index 00000000000..e2a71ba907e --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/dma.h @@ -0,0 +1,57 @@ +/* + * file: include/asm-blackfin/mach-bf518/dma.h + * based on: include/asm-blackfin/mach-bf527/dma.h + * author: Michael Hennerich (michael.hennerich@analog.com) + * + * created: + * description: + * system DMA map + * rev: + * + * modified: + * + * + * bugs: enter bugs at http://blackfin.uclinux.org/ + * + * this program is free software; you can redistribute it and/or modify + * it under the terms of the gnu general public license as published by + * the free software foundation; either version 2, or (at your option) + * any later version. + * + * this program is distributed in the hope that it will be useful, + * but without any warranty; without even the implied warranty of + * merchantability or fitness for a particular purpose. see the + * gnu general public license for more details. + * + * you should have received a copy of the gnu general public license + * along with this program; see the file copying. + * if not, write to the free software foundation, + * 59 temple place - suite 330, boston, ma 02111-1307, usa. + */ + +#ifndef _MACH_DMA_H_ +#define _MACH_DMA_H_ + +#define MAX_BLACKFIN_DMA_CHANNEL 16 + +#define CH_PPI 0 /* PPI receive/transmit */ +#define CH_EMAC_RX 1 /* Ethernet MAC receive */ +#define CH_EMAC_TX 2 /* Ethernet MAC transmit */ +#define CH_SPORT0_RX 3 /* SPORT0 receive */ +#define CH_SPORT0_TX 4 /* SPORT0 transmit */ +#define CH_RSI 4 /* RSI */ +#define CH_SPORT1_RX 5 /* SPORT1 receive */ +#define CH_SPI1 5 /* SPI1 transmit/receive */ +#define CH_SPORT1_TX 6 /* SPORT1 transmit */ +#define CH_SPI0 7 /* SPI0 transmit/receive */ +#define CH_UART0_RX 8 /* UART0 receive */ +#define CH_UART0_TX 9 /* UART0 transmit */ +#define CH_UART1_RX 10 /* UART1 receive */ +#define CH_UART1_TX 11 /* UART1 transmit */ + +#define CH_MEM_STREAM0_SRC 12 /* RX */ +#define CH_MEM_STREAM0_DEST 13 /* TX */ +#define CH_MEM_STREAM1_SRC 14 /* RX */ +#define CH_MEM_STREAM1_DEST 15 /* TX */ + +#endif diff --git a/arch/blackfin/mach-bf518/include/mach/irq.h b/arch/blackfin/mach-bf518/include/mach/irq.h new file mode 100644 index 00000000000..e5062f107ae --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/irq.h @@ -0,0 +1,260 @@ +/* + * file: include/asm-blackfin/mach-bf518/irq.h + * based on: include/asm-blackfin/mach-bf527/irq.h + * author: Michael Hennerich (michael.hennerich@analog.com) + * + * created: + * description: + * system mmr register map + * rev: + * + * modified: + * + * + * bugs: enter bugs at http://blackfin.uclinux.org/ + * + * this program is free software; you can redistribute it and/or modify + * it under the terms of the gnu general public license as published by + * the free software foundation; either version 2, or (at your option) + * any later version. + * + * this program is distributed in the hope that it will be useful, + * but without any warranty; without even the implied warranty of + * merchantability or fitness for a particular purpose. see the + * gnu general public license for more details. + * + * you should have received a copy of the gnu general public license + * along with this program; see the file copying. + * if not, write to the free software foundation, + * 59 temple place - suite 330, boston, ma 02111-1307, usa. + */ + +#ifndef _BF518_IRQ_H_ +#define _BF518_IRQ_H_ + +/* + * Interrupt source definitions + Event Source Core Event Name + Core Emulation ** + Events (highest priority) EMU 0 + Reset RST 1 + NMI NMI 2 + Exception EVX 3 + Reserved -- 4 + Hardware Error IVHW 5 + Core Timer IVTMR 6 * + + ..... + + Software Interrupt 1 IVG14 31 + Software Interrupt 2 -- + (lowest priority) IVG15 32 * +*/ + +#define NR_PERI_INTS (2 * 32) + +/* The ABSTRACT IRQ definitions */ +/** the first seven of the following are fixed, the rest you change if you need to **/ +#define IRQ_EMU 0 /* Emulation */ +#define IRQ_RST 1 /* reset */ +#define IRQ_NMI 2 /* Non Maskable */ +#define IRQ_EVX 3 /* Exception */ +#define IRQ_UNUSED 4 /* - unused interrupt */ +#define IRQ_HWERR 5 /* Hardware Error */ +#define IRQ_CORETMR 6 /* Core timer */ + +#define BFIN_IRQ(x) ((x) + 7) + +#define IRQ_PLL_WAKEUP BFIN_IRQ(0) /* PLL Wakeup Interrupt */ +#define IRQ_DMA0_ERROR BFIN_IRQ(1) /* DMA Error 0 (generic) */ +#define IRQ_DMAR0_BLK BFIN_IRQ(2) /* DMAR0 Block Interrupt */ +#define IRQ_DMAR1_BLK BFIN_IRQ(3) /* DMAR1 Block Interrupt */ +#define IRQ_DMAR0_OVR BFIN_IRQ(4) /* DMAR0 Overflow Error */ +#define IRQ_DMAR1_OVR BFIN_IRQ(5) /* DMAR1 Overflow Error */ +#define IRQ_PPI_ERROR BFIN_IRQ(6) /* PPI Error */ +#define IRQ_MAC_ERROR BFIN_IRQ(7) /* MAC Status */ +#define IRQ_SPORT0_ERROR BFIN_IRQ(8) /* SPORT0 Status */ +#define IRQ_SPORT1_ERROR BFIN_IRQ(9) /* SPORT1 Status */ +#define IRQ_PTP_ERROR BFIN_IRQ(10) /* PTP Error Interrupt */ +#define IRQ_UART0_ERROR BFIN_IRQ(12) /* UART0 Status */ +#define IRQ_UART1_ERROR BFIN_IRQ(13) /* UART1 Status */ +#define IRQ_RTC BFIN_IRQ(14) /* RTC */ +#define IRQ_PPI BFIN_IRQ(15) /* DMA Channel 0 (PPI) */ +#define IRQ_SPORT0_RX BFIN_IRQ(16) /* DMA 3 Channel (SPORT0 RX) */ +#define IRQ_SPORT0_TX BFIN_IRQ(17) /* DMA 4 Channel (SPORT0 TX) */ +#define IRQ_RSI BFIN_IRQ(17) /* DMA 4 Channel (RSI) */ +#define IRQ_SPORT1_RX BFIN_IRQ(18) /* DMA 5 Channel (SPORT1 RX/SPI) */ +#define IRQ_SPI1 BFIN_IRQ(18) /* DMA 5 Channel (SPI1) */ +#define IRQ_SPORT1_TX BFIN_IRQ(19) /* DMA 6 Channel (SPORT1 TX) */ +#define IRQ_TWI BFIN_IRQ(20) /* TWI */ +#define IRQ_SPI0 BFIN_IRQ(21) /* DMA 7 Channel (SPI0) */ +#define IRQ_UART0_RX BFIN_IRQ(22) /* DMA8 Channel (UART0 RX) */ +#define IRQ_UART0_TX BFIN_IRQ(23) /* DMA9 Channel (UART0 TX) */ +#define IRQ_UART1_RX BFIN_IRQ(24) /* DMA10 Channel (UART1 RX) */ +#define IRQ_UART1_TX BFIN_IRQ(25) /* DMA11 Channel (UART1 TX) */ +#define IRQ_OPTSEC BFIN_IRQ(26) /* OTPSEC Interrupt */ +#define IRQ_CNT BFIN_IRQ(27) /* GP Counter */ +#define IRQ_MAC_RX BFIN_IRQ(28) /* DMA1 Channel (MAC RX) */ +#define IRQ_PORTH_INTA BFIN_IRQ(29) /* Port H Interrupt A */ +#define IRQ_MAC_TX BFIN_IRQ(30) /* DMA2 Channel (MAC TX) */ +#define IRQ_PORTH_INTB BFIN_IRQ(31) /* Port H Interrupt B */ +#define IRQ_TMR0 BFIN_IRQ(32) /* Timer 0 */ +#define IRQ_TMR1 BFIN_IRQ(33) /* Timer 1 */ +#define IRQ_TMR2 BFIN_IRQ(34) /* Timer 2 */ +#define IRQ_TMR3 BFIN_IRQ(35) /* Timer 3 */ +#define IRQ_TMR4 BFIN_IRQ(36) /* Timer 4 */ +#define IRQ_TMR5 BFIN_IRQ(37) /* Timer 5 */ +#define IRQ_TMR6 BFIN_IRQ(38) /* Timer 6 */ +#define IRQ_TMR7 BFIN_IRQ(39) /* Timer 7 */ +#define IRQ_PORTG_INTA BFIN_IRQ(40) /* Port G Interrupt A */ +#define IRQ_PORTG_INTB BFIN_IRQ(41) /* Port G Interrupt B */ +#define IRQ_MEM_DMA0 BFIN_IRQ(42) /* MDMA Stream 0 */ +#define IRQ_MEM_DMA1 BFIN_IRQ(43) /* MDMA Stream 1 */ +#define IRQ_WATCH BFIN_IRQ(44) /* Software Watchdog Timer */ +#define IRQ_PORTF_INTA BFIN_IRQ(45) /* Port F Interrupt A */ +#define IRQ_PORTF_INTB BFIN_IRQ(46) /* Port F Interrupt B */ +#define IRQ_SPI0_ERROR BFIN_IRQ(47) /* SPI0 Status */ +#define IRQ_SPI1_ERROR BFIN_IRQ(48) /* SPI1 Error */ +#define IRQ_RSI_INT0 BFIN_IRQ(51) /* RSI Interrupt0 */ +#define IRQ_RSI_INT1 BFIN_IRQ(52) /* RSI Interrupt1 */ +#define IRQ_PWM_TRIP BFIN_IRQ(53) /* PWM Trip Interrupt */ +#define IRQ_PWM_SYNC BFIN_IRQ(54) /* PWM Sync Interrupt */ +#define IRQ_PTP_STAT BFIN_IRQ(55) /* PTP Stat Interrupt */ + +#define SYS_IRQS BFIN_IRQ(63) /* 70 */ + +#define IRQ_PF0 71 +#define IRQ_PF1 72 +#define IRQ_PF2 73 +#define IRQ_PF3 74 +#define IRQ_PF4 75 +#define IRQ_PF5 76 +#define IRQ_PF6 77 +#define IRQ_PF7 78 +#define IRQ_PF8 79 +#define IRQ_PF9 80 +#define IRQ_PF10 81 +#define IRQ_PF11 82 +#define IRQ_PF12 83 +#define IRQ_PF13 84 +#define IRQ_PF14 85 +#define IRQ_PF15 86 + +#define IRQ_PG0 87 +#define IRQ_PG1 88 +#define IRQ_PG2 89 +#define IRQ_PG3 90 +#define IRQ_PG4 91 +#define IRQ_PG5 92 +#define IRQ_PG6 93 +#define IRQ_PG7 94 +#define IRQ_PG8 95 +#define IRQ_PG9 96 +#define IRQ_PG10 97 +#define IRQ_PG11 98 +#define IRQ_PG12 99 +#define IRQ_PG13 100 +#define IRQ_PG14 101 +#define IRQ_PG15 102 + +#define IRQ_PH0 103 +#define IRQ_PH1 104 +#define IRQ_PH2 105 +#define IRQ_PH3 106 +#define IRQ_PH4 107 +#define IRQ_PH5 108 +#define IRQ_PH6 109 +#define IRQ_PH7 110 +#define IRQ_PH8 111 +#define IRQ_PH9 112 +#define IRQ_PH10 113 +#define IRQ_PH11 114 +#define IRQ_PH12 115 +#define IRQ_PH13 116 +#define IRQ_PH14 117 +#define IRQ_PH15 118 + +#define GPIO_IRQ_BASE IRQ_PF0 + +#define NR_IRQS (IRQ_PH15 + 1) + +#define IVG7 7 +#define IVG8 8 +#define IVG9 9 +#define IVG10 10 +#define IVG11 11 +#define IVG12 12 +#define IVG13 13 +#define IVG14 14 +#define IVG15 15 + +/* IAR0 BIT FIELDS */ +#define IRQ_PLL_WAKEUP_POS 0 +#define IRQ_DMA0_ERROR_POS 4 +#define IRQ_DMAR0_BLK_POS 8 +#define IRQ_DMAR1_BLK_POS 12 +#define IRQ_DMAR0_OVR_POS 16 +#define IRQ_DMAR1_OVR_POS 20 +#define IRQ_PPI_ERROR_POS 24 +#define IRQ_MAC_ERROR_POS 28 + +/* IAR1 BIT FIELDS */ +#define IRQ_SPORT0_ERROR_POS 0 +#define IRQ_SPORT1_ERROR_POS 4 +#define IRQ_PTP_ERROR_POS 8 +#define IRQ_UART0_ERROR_POS 16 +#define IRQ_UART1_ERROR_POS 20 +#define IRQ_RTC_POS 24 +#define IRQ_PPI_POS 28 + +/* IAR2 BIT FIELDS */ +#define IRQ_SPORT0_RX_POS 0 +#define IRQ_SPORT0_TX_POS 4 +#define IRQ_RSI_POS 4 +#define IRQ_SPORT1_RX_POS 8 +#define IRQ_SPI1_POS 8 +#define IRQ_SPORT1_TX_POS 12 +#define IRQ_TWI_POS 16 +#define IRQ_SPI0_POS 20 +#define IRQ_UART0_RX_POS 24 +#define IRQ_UART0_TX_POS 28 + +/* IAR3 BIT FIELDS */ +#define IRQ_UART1_RX_POS 0 +#define IRQ_UART1_TX_POS 4 +#define IRQ_OPTSEC_POS 8 +#define IRQ_CNT_POS 12 +#define IRQ_MAC_RX_POS 16 +#define IRQ_PORTH_INTA_POS 20 +#define IRQ_MAC_TX_POS 24 +#define IRQ_PORTH_INTB_POS 28 + +/* IAR4 BIT FIELDS */ +#define IRQ_TMR0_POS 0 +#define IRQ_TMR1_POS 4 +#define IRQ_TMR2_POS 8 +#define IRQ_TMR3_POS 12 +#define IRQ_TMR4_POS 16 +#define IRQ_TMR5_POS 20 +#define IRQ_TMR6_POS 24 +#define IRQ_TMR7_POS 28 + +/* IAR5 BIT FIELDS */ +#define IRQ_PORTG_INTA_POS 0 +#define IRQ_PORTG_INTB_POS 4 +#define IRQ_MEM_DMA0_POS 8 +#define IRQ_MEM_DMA1_POS 12 +#define IRQ_WATCH_POS 16 +#define IRQ_PORTF_INTA_POS 20 +#define IRQ_PORTF_INTB_POS 24 +#define IRQ_SPI0_ERROR_POS 28 + +/* IAR6 BIT FIELDS */ +#define IRQ_SPI1_ERROR_POS 0 +#define IRQ_RSI_INT0_POS 12 +#define IRQ_RSI_INT1_POS 16 +#define IRQ_PWM_TRIP_POS 20 +#define IRQ_PWM_SYNC_POS 24 +#define IRQ_PTP_STAT_POS 28 + +#endif /* _BF518_IRQ_H_ */ diff --git a/arch/blackfin/mach-bf518/include/mach/mem_init.h b/arch/blackfin/mach-bf518/include/mach/mem_init.h new file mode 100644 index 00000000000..2f4f4092fb5 --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/mem_init.h @@ -0,0 +1,310 @@ +/* + * File: include/asm-blackfin/mach-bf518/mem_init.h + * Based on: + * Author: + * + * Created: + * Description: + * + * Rev: + * + * Modified: + * Copyright 2004-2007 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#if (CONFIG_MEM_MT48LC16M16A2TG_75 || CONFIG_MEM_MT48LC64M4A2FB_7E || CONFIG_MEM_MT48LC16M8A2TG_75 || CONFIG_MEM_GENERIC_BOARD || CONFIG_MEM_MT48LC32M8A2_75 || CONFIG_MEM_MT48LC32M16A2TG_75) +#if (CONFIG_SCLK_HZ > 119402985) +#define SDRAM_tRP TRP_2 +#define SDRAM_tRP_num 2 +#define SDRAM_tRAS TRAS_7 +#define SDRAM_tRAS_num 7 +#define SDRAM_tRCD TRCD_2 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 104477612) && (CONFIG_SCLK_HZ <= 119402985) +#define SDRAM_tRP TRP_2 +#define SDRAM_tRP_num 2 +#define SDRAM_tRAS TRAS_6 +#define SDRAM_tRAS_num 6 +#define SDRAM_tRCD TRCD_2 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 89552239) && (CONFIG_SCLK_HZ <= 104477612) +#define SDRAM_tRP TRP_2 +#define SDRAM_tRP_num 2 +#define SDRAM_tRAS TRAS_5 +#define SDRAM_tRAS_num 5 +#define SDRAM_tRCD TRCD_2 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 74626866) && (CONFIG_SCLK_HZ <= 89552239) +#define SDRAM_tRP TRP_2 +#define SDRAM_tRP_num 2 +#define SDRAM_tRAS TRAS_4 +#define SDRAM_tRAS_num 4 +#define SDRAM_tRCD TRCD_2 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 66666667) && (CONFIG_SCLK_HZ <= 74626866) +#define SDRAM_tRP TRP_2 +#define SDRAM_tRP_num 2 +#define SDRAM_tRAS TRAS_3 +#define SDRAM_tRAS_num 3 +#define SDRAM_tRCD TRCD_2 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 59701493) && (CONFIG_SCLK_HZ <= 66666667) +#define SDRAM_tRP TRP_1 +#define SDRAM_tRP_num 1 +#define SDRAM_tRAS TRAS_4 +#define SDRAM_tRAS_num 3 +#define SDRAM_tRCD TRCD_1 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 44776119) && (CONFIG_SCLK_HZ <= 59701493) +#define SDRAM_tRP TRP_1 +#define SDRAM_tRP_num 1 +#define SDRAM_tRAS TRAS_3 +#define SDRAM_tRAS_num 3 +#define SDRAM_tRCD TRCD_1 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 29850746) && (CONFIG_SCLK_HZ <= 44776119) +#define SDRAM_tRP TRP_1 +#define SDRAM_tRP_num 1 +#define SDRAM_tRAS TRAS_2 +#define SDRAM_tRAS_num 2 +#define SDRAM_tRCD TRCD_1 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ <= 29850746) +#define SDRAM_tRP TRP_1 +#define SDRAM_tRP_num 1 +#define SDRAM_tRAS TRAS_1 +#define SDRAM_tRAS_num 1 +#define SDRAM_tRCD TRCD_1 +#define SDRAM_tWR TWR_2 +#endif +#endif + +#if (CONFIG_MEM_MT48LC16M16A2TG_75) + /*SDRAM INFORMATION: */ +#define SDRAM_Tref 64 /* Refresh period in milliseconds */ +#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ +#define SDRAM_CL CL_3 +#endif + +#if (CONFIG_MEM_MT48LC16M8A2TG_75) + /*SDRAM INFORMATION: */ +#define SDRAM_Tref 64 /* Refresh period in milliseconds */ +#define SDRAM_NRA 4096 /* Number of row addresses in SDRAM */ +#define SDRAM_CL CL_3 +#endif + +#if (CONFIG_MEM_MT48LC32M8A2_75) + /*SDRAM INFORMATION: */ +#define SDRAM_Tref 64 /* Refresh period in milliseconds */ +#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ +#define SDRAM_CL CL_3 +#endif + +#if (CONFIG_MEM_MT48LC64M4A2FB_7E) + /*SDRAM INFORMATION: */ +#define SDRAM_Tref 64 /* Refresh period in milliseconds */ +#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ +#define SDRAM_CL CL_3 +#endif + +#if (CONFIG_MEM_GENERIC_BOARD) + /*SDRAM INFORMATION: Modify this for your board */ +#define SDRAM_Tref 64 /* Refresh period in milliseconds */ +#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ +#define SDRAM_CL CL_3 +#endif + +#if (CONFIG_MEM_MT48LC32M16A2TG_75) + /*SDRAM INFORMATION: */ +#define SDRAM_Tref 64 /* Refresh period in milliseconds */ +#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ +#define SDRAM_CL CL_3 +#endif + +/* Equation from section 17 (p17-46) of BF533 HRM */ +#define mem_SDRRC (((CONFIG_SCLK_HZ / 1000) * SDRAM_Tref) / SDRAM_NRA) - (SDRAM_tRAS_num + SDRAM_tRP_num) + +/* Enable SCLK Out */ +#define mem_SDGCTL (SCTLE | SDRAM_CL | SDRAM_tRAS | SDRAM_tRP | SDRAM_tRCD | SDRAM_tWR | PSS) + +#if defined CONFIG_CLKIN_HALF +#define CLKIN_HALF 1 +#else +#define CLKIN_HALF 0 +#endif + +#if defined CONFIG_PLL_BYPASS +#define PLL_BYPASS 1 +#else +#define PLL_BYPASS 0 +#endif + +/***************************************Currently Not Being Used *********************************/ +#define flash_EBIU_AMBCTL_WAT ((CONFIG_FLASH_SPEED_BWAT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1 +#define flash_EBIU_AMBCTL_RAT ((CONFIG_FLASH_SPEED_BRAT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1 +#define flash_EBIU_AMBCTL_HT ((CONFIG_FLASH_SPEED_BHT * 4) / (4000000000 / CONFIG_SCLK_HZ)) +#define flash_EBIU_AMBCTL_ST ((CONFIG_FLASH_SPEED_BST * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1 +#define flash_EBIU_AMBCTL_TT ((CONFIG_FLASH_SPEED_BTT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1 + +#if (flash_EBIU_AMBCTL_TT > 3) +#define flash_EBIU_AMBCTL0_TT B0TT_4 +#endif +#if (flash_EBIU_AMBCTL_TT == 3) +#define flash_EBIU_AMBCTL0_TT B0TT_3 +#endif +#if (flash_EBIU_AMBCTL_TT == 2) +#define flash_EBIU_AMBCTL0_TT B0TT_2 +#endif +#if (flash_EBIU_AMBCTL_TT < 2) +#define flash_EBIU_AMBCTL0_TT B0TT_1 +#endif + +#if (flash_EBIU_AMBCTL_ST > 3) +#define flash_EBIU_AMBCTL0_ST B0ST_4 +#endif +#if (flash_EBIU_AMBCTL_ST == 3) +#define flash_EBIU_AMBCTL0_ST B0ST_3 +#endif +#if (flash_EBIU_AMBCTL_ST == 2) +#define flash_EBIU_AMBCTL0_ST B0ST_2 +#endif +#if (flash_EBIU_AMBCTL_ST < 2) +#define flash_EBIU_AMBCTL0_ST B0ST_1 +#endif + +#if (flash_EBIU_AMBCTL_HT > 2) +#define flash_EBIU_AMBCTL0_HT B0HT_3 +#endif +#if (flash_EBIU_AMBCTL_HT == 2) +#define flash_EBIU_AMBCTL0_HT B0HT_2 +#endif +#if (flash_EBIU_AMBCTL_HT == 1) +#define flash_EBIU_AMBCTL0_HT B0HT_1 +#endif +#if (flash_EBIU_AMBCTL_HT == 0 && CONFIG_FLASH_SPEED_BHT == 0) +#define flash_EBIU_AMBCTL0_HT B0HT_0 +#endif +#if (flash_EBIU_AMBCTL_HT == 0 && CONFIG_FLASH_SPEED_BHT != 0) +#define flash_EBIU_AMBCTL0_HT B0HT_1 +#endif + +#if (flash_EBIU_AMBCTL_WAT > 14) +#define flash_EBIU_AMBCTL0_WAT B0WAT_15 +#endif +#if (flash_EBIU_AMBCTL_WAT == 14) +#define flash_EBIU_AMBCTL0_WAT B0WAT_14 +#endif +#if (flash_EBIU_AMBCTL_WAT == 13) +#define flash_EBIU_AMBCTL0_WAT B0WAT_13 +#endif +#if (flash_EBIU_AMBCTL_WAT == 12) +#define flash_EBIU_AMBCTL0_WAT B0WAT_12 +#endif +#if (flash_EBIU_AMBCTL_WAT == 11) +#define flash_EBIU_AMBCTL0_WAT B0WAT_11 +#endif +#if (flash_EBIU_AMBCTL_WAT == 10) +#define flash_EBIU_AMBCTL0_WAT B0WAT_10 +#endif +#if (flash_EBIU_AMBCTL_WAT == 9) +#define flash_EBIU_AMBCTL0_WAT B0WAT_9 +#endif +#if (flash_EBIU_AMBCTL_WAT == 8) +#define flash_EBIU_AMBCTL0_WAT B0WAT_8 +#endif +#if (flash_EBIU_AMBCTL_WAT == 7) +#define flash_EBIU_AMBCTL0_WAT B0WAT_7 +#endif +#if (flash_EBIU_AMBCTL_WAT == 6) +#define flash_EBIU_AMBCTL0_WAT B0WAT_6 +#endif +#if (flash_EBIU_AMBCTL_WAT == 5) +#define flash_EBIU_AMBCTL0_WAT B0WAT_5 +#endif +#if (flash_EBIU_AMBCTL_WAT == 4) +#define flash_EBIU_AMBCTL0_WAT B0WAT_4 +#endif +#if (flash_EBIU_AMBCTL_WAT == 3) +#define flash_EBIU_AMBCTL0_WAT B0WAT_3 +#endif +#if (flash_EBIU_AMBCTL_WAT == 2) +#define flash_EBIU_AMBCTL0_WAT B0WAT_2 +#endif +#if (flash_EBIU_AMBCTL_WAT == 1) +#define flash_EBIU_AMBCTL0_WAT B0WAT_1 +#endif + +#if (flash_EBIU_AMBCTL_RAT > 14) +#define flash_EBIU_AMBCTL0_RAT B0RAT_15 +#endif +#if (flash_EBIU_AMBCTL_RAT == 14) +#define flash_EBIU_AMBCTL0_RAT B0RAT_14 +#endif +#if (flash_EBIU_AMBCTL_RAT == 13) +#define flash_EBIU_AMBCTL0_RAT B0RAT_13 +#endif +#if (flash_EBIU_AMBCTL_RAT == 12) +#define flash_EBIU_AMBCTL0_RAT B0RAT_12 +#endif +#if (flash_EBIU_AMBCTL_RAT == 11) +#define flash_EBIU_AMBCTL0_RAT B0RAT_11 +#endif +#if (flash_EBIU_AMBCTL_RAT == 10) +#define flash_EBIU_AMBCTL0_RAT B0RAT_10 +#endif +#if (flash_EBIU_AMBCTL_RAT == 9) +#define flash_EBIU_AMBCTL0_RAT B0RAT_9 +#endif +#if (flash_EBIU_AMBCTL_RAT == 8) +#define flash_EBIU_AMBCTL0_RAT B0RAT_8 +#endif +#if (flash_EBIU_AMBCTL_RAT == 7) +#define flash_EBIU_AMBCTL0_RAT B0RAT_7 +#endif +#if (flash_EBIU_AMBCTL_RAT == 6) +#define flash_EBIU_AMBCTL0_RAT B0RAT_6 +#endif +#if (flash_EBIU_AMBCTL_RAT == 5) +#define flash_EBIU_AMBCTL0_RAT B0RAT_5 +#endif +#if (flash_EBIU_AMBCTL_RAT == 4) +#define flash_EBIU_AMBCTL0_RAT B0RAT_4 +#endif +#if (flash_EBIU_AMBCTL_RAT == 3) +#define flash_EBIU_AMBCTL0_RAT B0RAT_3 +#endif +#if (flash_EBIU_AMBCTL_RAT == 2) +#define flash_EBIU_AMBCTL0_RAT B0RAT_2 +#endif +#if (flash_EBIU_AMBCTL_RAT == 1) +#define flash_EBIU_AMBCTL0_RAT B0RAT_1 +#endif + +#define flash_EBIU_AMBCTL0 \ + (flash_EBIU_AMBCTL0_WAT | flash_EBIU_AMBCTL0_RAT | flash_EBIU_AMBCTL0_HT | \ + flash_EBIU_AMBCTL0_ST | flash_EBIU_AMBCTL0_TT | CONFIG_FLASH_SPEED_RDYEN) diff --git a/arch/blackfin/mach-bf518/include/mach/mem_map.h b/arch/blackfin/mach-bf518/include/mach/mem_map.h new file mode 100644 index 00000000000..10f678f3c5c --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/mem_map.h @@ -0,0 +1,102 @@ +/* + * file: include/asm-blackfin/mach-bf518/mem_map.h + * based on: include/asm-blackfin/mach-bf527/mem_map.h + * author: Bryan Wu <cooloney@kernel.org> + * + * created: + * description: + * Memory MAP Common header file for blackfin BF518/6/4/2 of processors. + * rev: + * + * modified: + * + * bugs: enter bugs at http://blackfin.uclinux.org/ + * + * this program is free software; you can redistribute it and/or modify + * it under the terms of the gnu general public license as published by + * the free software foundation; either version 2, or (at your option) + * any later version. + * + * this program is distributed in the hope that it will be useful, + * but without any warranty; without even the implied warranty of + * merchantability or fitness for a particular purpose. see the + * gnu general public license for more details. + * + * you should have received a copy of the gnu general public license + * along with this program; see the file copying. + * if not, write to the free software foundation, + * 59 temple place - suite 330, boston, ma 02111-1307, usa. + */ + +#ifndef _MEM_MAP_518_H_ +#define _MEM_MAP_518_H_ + +#define COREMMR_BASE 0xFFE00000 /* Core MMRs */ +#define SYSMMR_BASE 0xFFC00000 /* System MMRs */ + +/* Async Memory Banks */ +#define ASYNC_BANK3_BASE 0x20300000 /* Async Bank 3 */ +#define ASYNC_BANK3_SIZE 0x00100000 /* 1M */ +#define ASYNC_BANK2_BASE 0x20200000 /* Async Bank 2 */ +#define ASYNC_BANK2_SIZE 0x00100000 /* 1M */ +#define ASYNC_BANK1_BASE 0x20100000 /* Async Bank 1 */ +#define ASYNC_BANK1_SIZE 0x00100000 /* 1M */ +#define ASYNC_BANK0_BASE 0x20000000 /* Async Bank 0 */ +#define ASYNC_BANK0_SIZE 0x00100000 /* 1M */ + +/* Boot ROM Memory */ + +#define BOOT_ROM_START 0xEF000000 +#define BOOT_ROM_LENGTH 0x8000 + +/* Level 1 Memory */ + +/* Memory Map for ADSP-BF518/6/4/2 processors */ + +#ifdef CONFIG_BFIN_ICACHE +#define BFIN_ICACHESIZE (16 * 1024) +#else +#define BFIN_ICACHESIZE (0) +#endif + +#define L1_CODE_START 0xFFA00000 +#define L1_DATA_A_START 0xFF800000 +#define L1_DATA_B_START 0xFF900000 + +#define L1_CODE_LENGTH 0xC000 + +#ifdef CONFIG_BFIN_DCACHE + +#ifdef CONFIG_BFIN_DCACHE_BANKA +#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0) +#define L1_DATA_A_LENGTH (0x8000 - 0x4000) +#define L1_DATA_B_LENGTH 0x8000 +#define BFIN_DCACHESIZE (16 * 1024) +#define BFIN_DSUPBANKS 1 +#else +#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0) +#define L1_DATA_A_LENGTH (0x8000 - 0x4000) +#define L1_DATA_B_LENGTH (0x8000 - 0x4000) +#define BFIN_DCACHESIZE (32 * 1024) +#define BFIN_DSUPBANKS 2 +#endif + +#else +#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0) +#define L1_DATA_A_LENGTH 0x8000 +#define L1_DATA_B_LENGTH 0x8000 +#define BFIN_DCACHESIZE 0 +#define BFIN_DSUPBANKS 0 +#endif /*CONFIG_BFIN_DCACHE */ + +/* Level 2 Memory - none */ + +#define L2_START 0 +#define L2_LENGTH 0 + +/* Scratch Pad Memory */ + +#define L1_SCRATCH_START 0xFFB00000 +#define L1_SCRATCH_LENGTH 0x1000 + +#endif /* _MEM_MAP_518_H_ */ diff --git a/arch/blackfin/mach-bf518/include/mach/portmux.h b/arch/blackfin/mach-bf518/include/mach/portmux.h new file mode 100644 index 00000000000..5af30c8ecfe --- /dev/null +++ b/arch/blackfin/mach-bf518/include/mach/portmux.h @@ -0,0 +1,188 @@ +#ifndef _MACH_PORTMUX_H_ +#define _MACH_PORTMUX_H_ + +#define MAX_RESOURCES MAX_BLACKFIN_GPIOS + +/* EMAC MII/RMII Port Mux */ +#define P_MII0_ETxD2 (P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(0)) +#define P_MII0_ERxD2 (P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(0)) +#define P_MII0_ETxD3 (P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(0)) +#define P_MII0_ERxD3 (P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(0)) +#define P_MII0_ERxCLK (P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(0)) +#define P_MII0_ERxDV (P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(0)) +#define P_MII0_COL (P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(0)) + +#define P_MII0_MDC (P_DEFINED | P_IDENT(GPIO_PF8) | P_FUNCT(0)) +#define P_MII0_MDIO (P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(0)) +#define P_MII0_ETxD0 (P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(0)) +#define P_MII0_ERxD0 (P_DEFINED | P_IDENT(GPIO_PF11) | P_FUNCT(0)) +#define P_MII0_ETxD1 (P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(0)) +#define P_MII0_ERxD1 (P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(0)) +#define P_MII0_ETxEn (P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(0)) +#define P_MII0_PHYINT (P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(0)) +#define P_MII0_CRS (P_DEFINED | P_IDENT(GPIO_PG0) | P_FUNCT(0)) +#define P_MII0_ERxER (P_DEFINED | P_IDENT(GPIO_PG1) | P_FUNCT(0)) +#define P_MII0_ETxCLK (P_DEFINED | P_IDENT(GPIO_PG2) | P_FUNCT(0)) + +#define P_MII {\ + P_MII0_ETxD0, \ + P_MII0_ETxD1, \ + P_MII0_ETxD2, \ + P_MII0_ETxD3, \ + P_MII0_ETxEN, \ + P_MII0_TxCLK, \ + P_MII0_PHYINT, \ + P_MII0_COL, \ + P_MII0_ERxD0, \ + P_MII0_ERxD1, \ + P_MII0_ERxD2, \ + P_MII0_ERxD3, \ + P_MII0_ERxDV, \ + P_MII0_ERxCLK, \ + P_MII0_ERxER, \ + P_MII0_CRS, \ + P_MII0_MDC, \ + P_MII0_MDIO, 0} + +#define P_RMII {\ + P_MII0_ETxD0, \ + P_MII0_ETxD1, \ + P_MII0_ETxEN, \ + P_MII0_ERxD0, \ + P_MII0_ERxD1, \ + P_MII0_ERxER, \ + P_MII0_TxCLK, \ + P_MII0_PHYINT, \ + P_MII0_CRS, \ + P_MII0_MDC, \ + P_MII0_MDIO, 0} + +/* PPI Port Mux */ +#define P_PPI0_D0 (P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(1)) +#define P_PPI0_D1 (P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(1)) +#define P_PPI0_D2 (P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(1)) +#define P_PPI0_D3 (P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(1)) +#define P_PPI0_D4 (P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(1)) +#define P_PPI0_D5 (P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(1)) +#define P_PPI0_D6 (P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(1)) +#define P_PPI0_D7 (P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(1)) +#define P_PPI0_D8 (P_DEFINED | P_IDENT(GPIO_PF8) | P_FUNCT(1)) +#define P_PPI0_D9 (P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(1)) +#define P_PPI0_D10 (P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(1)) +#define P_PPI0_D11 (P_DEFINED | P_IDENT(GPIO_PF11) | P_FUNCT(1)) +#define P_PPI0_D12 (P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(1)) +#define P_PPI0_D13 (P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(1)) +#define P_PPI0_D14 (P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(1)) +#define P_PPI0_D15 (P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(1)) + +#define P_PPI0_CLK (P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(1)) +#define P_PPI0_FS1 (P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(1)) +#define P_PPI0_FS2 (P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(1)) +#define P_PPI0_FS3 (P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(1)) + +/* SPI Port Mux */ +#define P_SPI0_SS (P_DEFINED | P_IDENT(GPIO_PG11) | P_FUNCT(0)) +#define P_SPI0_SCK (P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(0)) +#define P_SPI0_MISO (P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(0)) +#define P_SPI0_MOSI (P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(0)) + +#define P_SPI0_SSEL1 (P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(0)) +#define P_SPI0_SSEL2 (P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(0)) +#define P_SPI0_SSEL3 (P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(2)) +#define P_SPI0_SSEL4 (P_DEFINED | P_IDENT(GPIO_PG10) | P_FUNCT(2)) +#define P_SPI0_SSEL5 (P_DEFINED | P_IDENT(GPIO_PG3) | P_FUNCT(2)) + +#define P_SPI1_SS (P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(1)) +#define P_SPI1_SCK (P_DEFINED | P_IDENT(GPIO_PH1) | P_FUNCT(1)) +#define P_SPI1_MISO (P_DEFINED | P_IDENT(GPIO_PH2) | P_FUNCT(1)) +#define P_SPI1_MOSI (P_DEFINED | P_IDENT(GPIO_PH3) | P_FUNCT(1)) + +#define P_SPI1_SSEL1 (P_DEFINED | P_IDENT(GPIO_PH6) | P_FUNCT(2)) +#define P_SPI1_SSEL2 (P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(2)) +#define P_SPI1_SSEL3 (P_DEFINED | P_IDENT(GPIO_PG0) | P_FUNCT(2)) +#define P_SPI1_SSEL4 (P_DEFINED | P_IDENT(GPIO_PF8) | P_FUNCT(2)) +#define P_SPI1_SSEL5 (P_DEFINED | P_IDENT(GPIO_PG11) | P_FUNCT(2)) + +/* SPORT Port Mux */ +#define P_SPORT0_DRPRI (P_DEFINED | P_IDENT(GPIO_PG3) | P_FUNCT(0)) +#define P_SPORT0_RSCLK (P_DEFINED | P_IDENT(GPIO_PG4) | P_FUNCT(0)) +#define P_SPORT0_RFS (P_DEFINED | P_IDENT(GPIO_PG5) | P_FUNCT(0)) +#define P_SPORT0_TFS (P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(0)) +#define P_SPORT0_DTPRI (P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(0)) +#define P_SPORT0_TSCLK (P_DEFINED | P_IDENT(GPIO_PG8) | P_FUNCT(0)) +#define P_SPORT0_DTSEC (P_DEFINED | P_IDENT(GPIO_PG9) | P_FUNCT(0)) +#define P_SPORT0_DRSEC (P_DEFINED | P_IDENT(GPIO_PG10) | P_FUNCT(0)) + +#define P_SPORT1_DRPRI (P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(0)) +#define P_SPORT1_RFS (P_DEFINED | P_IDENT(GPIO_PH1) | P_FUNCT(0)) +#define P_SPORT1_RSCLK (P_DEFINED | P_IDENT(GPIO_PH2) | P_FUNCT(0)) +#define P_SPORT1_DTPRI (P_DEFINED | P_IDENT(GPIO_PH3) | P_FUNCT(0)) +#define P_SPORT1_TFS (P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(0)) +#define P_SPORT1_TSCLK (P_DEFINED | P_IDENT(GPIO_PH5) | P_FUNCT(0)) +#define P_SPORT1_DTSEC (P_DEFINED | P_IDENT(GPIO_PH6) | P_FUNCT(0)) +#define P_SPORT1_DRSEC (P_DEFINED | P_IDENT(GPIO_PH7) | P_FUNCT(0)) + +/* UART Port Mux */ +#define P_UART0_TX (P_DEFINED | P_IDENT(GPIO_PG9) | P_FUNCT(1)) +#define P_UART0_RX (P_DEFINED | P_IDENT(GPIO_PG10) | P_FUNCT(1)) + +#define P_UART1_TX (P_DEFINED | P_IDENT(GPIO_PH6) | P_FUNCT(1)) +#define P_UART1_RX (P_DEFINED | P_IDENT(GPIO_PH7) | P_FUNCT(1)) + +/* Timer */ +#define P_TMRCLK (P_DEFINED | P_IDENT(GPIO_PG5) | P_FUNCT(2)) +#define P_TMR0 (P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(2)) +#define P_TMR1 (P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(2)) +#define P_TMR2 (P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(2)) +#define P_TMR3 (P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(2)) +#define P_TMR4 (P_DEFINED | P_IDENT(GPIO_PG9) | P_FUNCT(2)) +#define P_TMR5 (P_DEFINED | P_IDENT(GPIO_PG4) | P_FUNCT(2)) +#define P_TMR6 (P_DEFINED | P_IDENT(GPIO_PG8) | P_FUNCT(2)) +#define P_TMR7 (P_DEFINED | P_IDENT(GPIO_PH7) | P_FUNCT(2)) + +/* DMA */ +#define P_DMAR1 (P_DEFINED | P_IDENT(GPIO_PG1) | P_FUNCT(1)) +#define P_DMAR0 (P_DEFINED | P_IDENT(GPIO_PG2) | P_FUNCT(1)) + +/* TWI */ +#define P_TWI0_SCL (P_DONTCARE) +#define P_TWI0_SDA (P_DONTCARE) + +/* PWM */ +#define P_PWM0_AH (P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(2)) +#define P_PWM0_AL (P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(2)) +#define P_PWM0_BH (P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(2)) +#define P_PWM0_BL (P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(2)) +#define P_PWM0_CH (P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(2)) +#define P_PWM0_CL (P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(2)) +#define P_PWM0_SYNC (P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(2)) + +#define P_PWM1_AH (P_DEFINED | P_IDENT(GPIO_PF11) | P_FUNCT(2)) +#define P_PWM1_AL (P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(2)) +#define P_PWM1_BH (P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(2)) +#define P_PWM1_BL (P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(2)) +#define P_PWM1_CH (P_DEFINED | P_IDENT(GPIO_PG1) | P_FUNCT(2)) +#define P_PWM1_CL (P_DEFINED | P_IDENT(GPIO_PG2) | P_FUNCT(2)) +#define P_PWM1_SYNC (P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(2)) + +#define P_PWM_TRIPB (P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(2)) + +/* RSI */ +#define P_RSI_DATA0 (P_DEFINED | P_IDENT(GPIO_PG3) | P_FUNCT(1)) +#define P_RSI_DATA1 (P_DEFINED | P_IDENT(GPIO_PG4) | P_FUNCT(1)) +#define P_RSI_DATA2 (P_DEFINED | P_IDENT(GPIO_PG5) | P_FUNCT(1)) +#define P_RSI_DATA3 (P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(1)) +#define P_RSI_DATA4 (P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(2)) +#define P_RSI_DATA5 (P_DEFINED | P_IDENT(GPIO_PH1) | P_FUNCT(2)) +#define P_RSI_DATA6 (P_DEFINED | P_IDENT(GPIO_PH2) | P_FUNCT(2)) +#define P_RSI_DATA7 (P_DEFINED | P_IDENT(GPIO_PH3) | P_FUNCT(2)) +#define P_RSI_CMD (P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(1)) +#define P_RSI_CLK (P_DEFINED | P_IDENT(GPIO_PG8) | P_FUNCT(1)) + +/* PTP */ +#define P_PTP_PPS (P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(2)) +#define P_PTP_CLKOUT (P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(2)) + +#define P_HWAIT (P_DEFINED | P_IDENT(GPIO_PG000000000) | P_FUNCT(1)) + +#endif /* _MACH_PORTMUX_H_ */ diff --git a/arch/blackfin/mach-bf518/ints-priority.c b/arch/blackfin/mach-bf518/ints-priority.c new file mode 100644 index 00000000000..c490c79194c --- /dev/null +++ b/arch/blackfin/mach-bf518/ints-priority.c @@ -0,0 +1,99 @@ +/* + * File: arch/blackfin/mach-bf518/ints-priority.c + * Based on: arch/blackfin/mach-bf527/ints-priority.c + * Author: Bryan Wu <cooloney@kernel.org> + * + * Created: + * Description: Set up the interrupt priorities + * + * Modified: + * Copyright 2004-2007 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <linux/module.h> +#include <linux/irq.h> +#include <asm/blackfin.h> + +void __init program_IAR(void) +{ + /* Program the IAR0 Register with the configured priority */ + bfin_write_SIC_IAR0(((CONFIG_IRQ_PLL_WAKEUP - 7) << IRQ_PLL_WAKEUP_POS) | + ((CONFIG_IRQ_DMA0_ERROR - 7) << IRQ_DMA0_ERROR_POS) | + ((CONFIG_IRQ_DMAR0_BLK - 7) << IRQ_DMAR0_BLK_POS) | + ((CONFIG_IRQ_DMAR1_BLK - 7) << IRQ_DMAR1_BLK_POS) | + ((CONFIG_IRQ_DMAR0_OVR - 7) << IRQ_DMAR0_OVR_POS) | + ((CONFIG_IRQ_DMAR1_OVR - 7) << IRQ_DMAR1_OVR_POS) | + ((CONFIG_IRQ_PPI_ERROR - 7) << IRQ_PPI_ERROR_POS) | + ((CONFIG_IRQ_MAC_ERROR - 7) << IRQ_MAC_ERROR_POS)); + + + bfin_write_SIC_IAR1(((CONFIG_IRQ_SPORT0_ERROR - 7) << IRQ_SPORT0_ERROR_POS) | + ((CONFIG_IRQ_SPORT1_ERROR - 7) << IRQ_SPORT1_ERROR_POS) | + ((CONFIG_IRQ_PTP_ERROR - 7) << IRQ_PTP_ERROR_POS) | + ((CONFIG_IRQ_UART0_ERROR - 7) << IRQ_UART0_ERROR_POS) | + ((CONFIG_IRQ_UART1_ERROR - 7) << IRQ_UART1_ERROR_POS) | + ((CONFIG_IRQ_RTC - 7) << IRQ_RTC_POS) | + ((CONFIG_IRQ_PPI - 7) << IRQ_PPI_POS)); + + bfin_write_SIC_IAR2(((CONFIG_IRQ_SPORT0_RX - 7) << IRQ_SPORT0_RX_POS) | + ((CONFIG_IRQ_SPORT0_TX - 7) << IRQ_SPORT0_TX_POS) | + ((CONFIG_IRQ_SPORT1_RX - 7) << IRQ_SPORT1_RX_POS) | + ((CONFIG_IRQ_SPORT1_TX - 7) << IRQ_SPORT1_TX_POS) | + ((CONFIG_IRQ_TWI - 7) << IRQ_TWI_POS) | + ((CONFIG_IRQ_SPI0 - 7) << IRQ_SPI0_POS) | + ((CONFIG_IRQ_UART0_RX - 7) << IRQ_UART0_RX_POS) | + ((CONFIG_IRQ_UART0_TX - 7) << IRQ_UART0_TX_POS)); + + bfin_write_SIC_IAR3(((CONFIG_IRQ_UART1_RX - 7) << IRQ_UART1_RX_POS) | + ((CONFIG_IRQ_UART1_TX - 7) << IRQ_UART1_TX_POS) | + ((CONFIG_IRQ_OPTSEC - 7) << IRQ_OPTSEC_POS) | + ((CONFIG_IRQ_CNT - 7) << IRQ_CNT_POS) | + ((CONFIG_IRQ_MAC_RX - 7) << IRQ_MAC_RX_POS) | + ((CONFIG_IRQ_PORTH_INTA - 7) << IRQ_PORTH_INTA_POS) | + ((CONFIG_IRQ_MAC_TX - 7) << IRQ_MAC_TX_POS) | + ((CONFIG_IRQ_PORTH_INTB - 7) << IRQ_PORTH_INTB_POS)); + + bfin_write_SIC_IAR4(((CONFIG_IRQ_TMR0 - 7) << IRQ_TMR0_POS) | + ((CONFIG_IRQ_TMR1 - 7) << IRQ_TMR1_POS) | + ((CONFIG_IRQ_TMR2 - 7) << IRQ_TMR2_POS) | + ((CONFIG_IRQ_TMR3 - 7) << IRQ_TMR3_POS) | + ((CONFIG_IRQ_TMR4 - 7) << IRQ_TMR4_POS) | + ((CONFIG_IRQ_TMR5 - 7) << IRQ_TMR5_POS) | + ((CONFIG_IRQ_TMR6 - 7) << IRQ_TMR6_POS) | + ((CONFIG_IRQ_TMR7 - 7) << IRQ_TMR7_POS)); + + bfin_write_SIC_IAR5(((CONFIG_IRQ_PORTG_INTA - 7) << IRQ_PORTG_INTA_POS) | + ((CONFIG_IRQ_PORTG_INTB - 7) << IRQ_PORTG_INTB_POS) | + ((CONFIG_IRQ_MEM_DMA0 - 7) << IRQ_MEM_DMA0_POS) | + ((CONFIG_IRQ_MEM_DMA1 - 7) << IRQ_MEM_DMA1_POS) | + ((CONFIG_IRQ_WATCH - 7) << IRQ_WATCH_POS) | + ((CONFIG_IRQ_PORTF_INTA - 7) << IRQ_PORTF_INTA_POS) | + ((CONFIG_IRQ_PORTF_INTB - 7) << IRQ_PORTF_INTB_POS) | + ((CONFIG_IRQ_SPI0_ERROR - 7) << IRQ_SPI0_ERROR_POS)); + + bfin_write_SIC_IAR6(((CONFIG_IRQ_SPI1_ERROR - 7) << IRQ_SPI1_ERROR_POS) | + ((CONFIG_IRQ_RSI_INT0 - 7) << IRQ_RSI_INT0_POS) | + ((CONFIG_IRQ_RSI_INT1 - 7) << IRQ_RSI_INT1_POS) | + ((CONFIG_IRQ_PWM_TRIP - 7) << IRQ_PWM_TRIP_POS) | + ((CONFIG_IRQ_PWM_SYNC - 7) << IRQ_PWM_SYNC_POS) | + ((CONFIG_IRQ_PTP_STAT - 7) << IRQ_PTP_STAT_POS)); + + SSYNC(); +} diff --git a/arch/blackfin/mach-common/dpmc_modes.S b/arch/blackfin/mach-common/dpmc_modes.S index 21f61605f1f..4da50bcd930 100644 --- a/arch/blackfin/mach-common/dpmc_modes.S +++ b/arch/blackfin/mach-common/dpmc_modes.S @@ -248,7 +248,7 @@ ENDPROC(_unset_dram_srfs) ENTRY(_set_sic_iwr) #if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) || \ - defined(CONFIG_BF538) || defined(CONFIG_BF539) + defined(CONFIG_BF538) || defined(CONFIG_BF539) || defined(CONFIG_BF51x) P0.H = hi(SIC_IWR0); P0.L = lo(SIC_IWR0); P1.H = hi(SIC_IWR1); diff --git a/arch/blackfin/mach-common/ints-priority.c b/arch/blackfin/mach-common/ints-priority.c index 5ae507f5988..c32fa695f8c 100644 --- a/arch/blackfin/mach-common/ints-priority.c +++ b/arch/blackfin/mach-common/ints-priority.c @@ -104,7 +104,8 @@ static void __init search_IAR(void) for (irqn = 0; irqn < NR_PERI_INTS; irqn++) { int iar_shift = (irqn & 7) * 4; if (ivg == (0xf & -#if defined(CONFIG_BF52x) || defined(CONFIG_BF538) || defined(CONFIG_BF539) +#if defined(CONFIG_BF52x) || defined(CONFIG_BF538) \ + || defined(CONFIG_BF539) || defined(CONFIG_BF51x) bfin_read32((unsigned long *)SIC_IAR0 + ((irqn % 32) >> 3) + ((irqn / 32) * ((SIC_IAR4 - SIC_IAR0) / 4))) >> iar_shift)) { @@ -543,7 +544,7 @@ static void bfin_demux_gpio_irq(unsigned int inta_irq, case IRQ_PORTF_INTA: irq = IRQ_PF0; break; -#elif defined(CONFIG_BF52x) +#elif defined(CONFIG_BF52x) || defined(CONFIG_BF51x) case IRQ_PORTF_INTA: irq = IRQ_PF0; break; @@ -990,7 +991,8 @@ int __init init_arch_irq(void) int irq; unsigned long ilat = 0; /* Disable all the peripheral intrs - page 4-29 HW Ref manual */ -#if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) || defined(BF538_FAMILY) +#if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) \ + || defined(BF538_FAMILY) || defined(CONFIG_BF51x) bfin_write_SIC_IMASK0(SIC_UNMASK_ALL); bfin_write_SIC_IMASK1(SIC_UNMASK_ALL); # ifdef CONFIG_BF54x @@ -1035,7 +1037,7 @@ int __init init_arch_irq(void) case IRQ_PINT1: case IRQ_PINT2: case IRQ_PINT3: -#elif defined(CONFIG_BF52x) +#elif defined(CONFIG_BF52x) || defined(CONFIG_BF51x) case IRQ_PORTF_INTA: case IRQ_PORTG_INTA: case IRQ_PORTH_INTA: @@ -1094,10 +1096,11 @@ int __init init_arch_irq(void) IMASK_IVG14 | IMASK_IVG13 | IMASK_IVG12 | IMASK_IVG11 | IMASK_IVG10 | IMASK_IVG9 | IMASK_IVG8 | IMASK_IVG7 | IMASK_IVGHW; -#if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) || defined(BF538_FAMILY) +#if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) \ + || defined(BF538_FAMILY) || defined(CONFIG_BF51x) bfin_write_SIC_IWR0(IWR_DISABLE_ALL); -#if defined(CONFIG_BF52x) - /* BF52x system reset does not properly reset SIC_IWR1 which +#if defined(CONFIG_BF52x) || defined(CONFIG_BF51x) + /* BF52x/BF51x system reset does not properly reset SIC_IWR1 which * will screw up the bootrom as it relies on MDMA0/1 waking it * up from IDLE instructions. See this report for more info: * http://blackfin.uclinux.org/gf/tracker/4323 @@ -1126,7 +1129,8 @@ void do_irq(int vec, struct pt_regs *fp) } else { struct ivgx *ivg = ivg7_13[vec - IVG7].ifirst; struct ivgx *ivg_stop = ivg7_13[vec - IVG7].istop; -#if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) || defined(BF538_FAMILY) +#if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) \ + || defined(BF538_FAMILY) || defined(CONFIG_BF51x) unsigned long sic_status[3]; sic_status[0] = bfin_read_SIC_ISR0() & bfin_read_SIC_IMASK0(); diff --git a/arch/blackfin/mach-common/pm.c b/arch/blackfin/mach-common/pm.c index f774d8aa5b0..ee33a8a988b 100644 --- a/arch/blackfin/mach-common/pm.c +++ b/arch/blackfin/mach-common/pm.c @@ -83,9 +83,9 @@ void bfin_pm_suspend_standby_enter(void) bfin_pm_standby_restore(); #if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) || \ - defined(CONFIG_BF538) || defined(CONFIG_BF539) + defined(CONFIG_BF538) || defined(CONFIG_BF539) || defined(CONFIG_BF51x) bfin_write_SIC_IWR0(IWR_DISABLE_ALL); -#if defined(CONFIG_BF52x) +#if defined(CONFIG_BF52x) || defined(CONFIG_BF51x) /* BF52x system reset does not properly reset SIC_IWR1 which * will screw up the bootrom as it relies on MDMA0/1 waking it * up from IDLE instructions. See this report for more info: |