summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--arch/arm/mach-ixp4xx/Kconfig8
-rw-r--r--arch/arm/mach-ixp4xx/Makefile2
-rw-r--r--arch/arm/mach-ixp4xx/include/mach/debug-macro.S2
-rw-r--r--arch/arm/mach-ixp4xx/include/mach/io.h6
-rw-r--r--arch/arm/mach-ixp4xx/vulcan-pci.c73
-rw-r--r--arch/arm/mach-ixp4xx/vulcan-setup.c246
-rw-r--r--drivers/crypto/ixp4xx_crypto.c21
-rw-r--r--drivers/net/arm/ixp4xx_eth.c2
-rw-r--r--drivers/net/wan/ixp4xx_hss.c2
9 files changed, 357 insertions, 5 deletions
diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig
index 9e5070da17a..6f991c5ae86 100644
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -140,6 +140,14 @@ config MACH_FSG
FSG-3 device. For more information on this platform,
see http://www.nslu2-linux.org/wiki/FSG3/HomePage
+config MACH_ARCOM_VULCAN
+ bool
+ prompt "Arcom/Eurotech Vulcan"
+ select PCI
+ help
+ Say 'Y' here if you want your kernel to support Arcom's
+ Vulcan board.
+
#
# Certain registers and IRQs are only enabled if supporting IXP465 CPUs
#
diff --git a/arch/arm/mach-ixp4xx/Makefile b/arch/arm/mach-ixp4xx/Makefile
index 47d1f60d23f..d807fc367dd 100644
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -16,6 +16,7 @@ obj-pci-$(CONFIG_MACH_DSMG600) += dsmg600-pci.o
obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
+obj-pci-$(CONFIG_MACH_ARCOM_VULCAN) += vulcan-pci.o
obj-y += common.o
@@ -31,6 +32,7 @@ obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o
obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
obj-$(CONFIG_MACH_FSG) += fsg-setup.o
obj-$(CONFIG_MACH_GORAMO_MLR) += goramo_mlr.o
+obj-$(CONFIG_MACH_ARCOM_VULCAN) += vulcan-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
diff --git a/arch/arm/mach-ixp4xx/include/mach/debug-macro.S b/arch/arm/mach-ixp4xx/include/mach/debug-macro.S
index 893873eb2a0..3fc66d6d00a 100644
--- a/arch/arm/mach-ixp4xx/include/mach/debug-macro.S
+++ b/arch/arm/mach-ixp4xx/include/mach/debug-macro.S
@@ -16,8 +16,10 @@
moveq \rx, #0xc8000000
movne \rx, #0xff000000
orrne \rx, \rx, #0x00b00000
+#ifdef __ARMEB__
add \rx,\rx,#3 @ Uart regs are at off set of 3 if
@ byte writes used - Big Endian.
+#endif
.endm
#define UART_SHIFT 2
diff --git a/arch/arm/mach-ixp4xx/include/mach/io.h b/arch/arm/mach-ixp4xx/include/mach/io.h
index 6ea7e2fb270..de274a1f19d 100644
--- a/arch/arm/mach-ixp4xx/include/mach/io.h
+++ b/arch/arm/mach-ixp4xx/include/mach/io.h
@@ -353,7 +353,7 @@ static inline unsigned int ioread8(const void __iomem *addr)
return (unsigned int)inb(port & PIO_MASK);
else
#ifndef CONFIG_IXP4XX_INDIRECT_PCI
- return (unsigned int)__raw_readb(port);
+ return (unsigned int)__raw_readb(addr);
#else
return (unsigned int)__indirect_readb(addr);
#endif
@@ -381,7 +381,7 @@ static inline unsigned int ioread16(const void __iomem *addr)
return (unsigned int)inw(port & PIO_MASK);
else
#ifndef CONFIG_IXP4XX_INDIRECT_PCI
- return le16_to_cpu(__raw_readw((u32)port));
+ return le16_to_cpu((__force __le16)__raw_readw(addr));
#else
return (unsigned int)__indirect_readw(addr);
#endif
@@ -440,7 +440,7 @@ static inline void iowrite8(u8 value, void __iomem *addr)
outb(value, port & PIO_MASK);
else
#ifndef CONFIG_IXP4XX_INDIRECT_PCI
- __raw_writeb(value, port);
+ __raw_writeb(value, addr);
#else
__indirect_writeb(value, addr);
#endif
diff --git a/arch/arm/mach-ixp4xx/vulcan-pci.c b/arch/arm/mach-ixp4xx/vulcan-pci.c
new file mode 100644
index 00000000000..f3111c6840e
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/vulcan-pci.c
@@ -0,0 +1,73 @@
+/*
+ * arch/arch/mach-ixp4xx/vulcan-pci.c
+ *
+ * Vulcan board-level PCI initialization
+ *
+ * Copyright (C) 2010 Marc Zyngier <maz@misterjones.org>
+ *
+ * based on ixdp425-pci.c:
+ * Copyright (C) 2002 Intel Corporation.
+ * Copyright (C) 2003-2004 MontaVista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <asm/mach/pci.h>
+#include <asm/mach-types.h>
+
+/* PCI controller GPIO to IRQ pin mappings */
+#define INTA 2
+#define INTB 3
+
+void __init vulcan_pci_preinit(void)
+{
+#ifndef CONFIG_IXP4XX_INDIRECT_PCI
+ /*
+ * Cardbus bridge wants way more than the SoC can actually offer,
+ * and leaves the whole PCI bus in a mess. Artificially limit it
+ * to 8MB per region. Of course indirect mode doesn't have this
+ * limitation...
+ */
+ pci_cardbus_mem_size = SZ_8M;
+ pr_info("Vulcan PCI: limiting CardBus memory size to %dMB\n",
+ (int)(pci_cardbus_mem_size >> 20));
+#endif
+ set_irq_type(IXP4XX_GPIO_IRQ(INTA), IRQ_TYPE_LEVEL_LOW);
+ set_irq_type(IXP4XX_GPIO_IRQ(INTB), IRQ_TYPE_LEVEL_LOW);
+ ixp4xx_pci_preinit();
+}
+
+static int __init vulcan_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ if (slot == 1)
+ return IXP4XX_GPIO_IRQ(INTA);
+
+ if (slot == 2)
+ return IXP4XX_GPIO_IRQ(INTB);
+
+ return -1;
+}
+
+struct hw_pci vulcan_pci __initdata = {
+ .nr_controllers = 1,
+ .preinit = vulcan_pci_preinit,
+ .swizzle = pci_std_swizzle,
+ .setup = ixp4xx_setup,
+ .scan = ixp4xx_scan_bus,
+ .map_irq = vulcan_map_irq,
+};
+
+int __init vulcan_pci_init(void)
+{
+ if (machine_is_arcom_vulcan())
+ pci_common_init(&vulcan_pci);
+ return 0;
+}
+
+subsys_initcall(vulcan_pci_init);
diff --git a/arch/arm/mach-ixp4xx/vulcan-setup.c b/arch/arm/mach-ixp4xx/vulcan-setup.c
new file mode 100644
index 00000000000..465cc5cce68
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/vulcan-setup.c
@@ -0,0 +1,246 @@
+/*
+ * arch/arm/mach-ixp4xx/vulcan-setup.c
+ *
+ * Arcom/Eurotech Vulcan board-setup
+ *
+ * Copyright (C) 2010 Marc Zyngier <maz@misterjones.org>
+ *
+ * based on fsg-setup.c:
+ * Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
+ */
+
+#include <linux/if_ether.h>
+#include <linux/irq.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/io.h>
+#include <linux/w1-gpio.h>
+#include <linux/mtd/plat-ram.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data vulcan_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource vulcan_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device vulcan_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &vulcan_flash_data,
+ },
+ .resource = &vulcan_flash_resource,
+ .num_resources = 1,
+};
+
+static struct platdata_mtd_ram vulcan_sram_data = {
+ .mapname = "Vulcan SRAM",
+ .bankwidth = 1,
+};
+
+static struct resource vulcan_sram_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device vulcan_sram = {
+ .name = "mtd-ram",
+ .id = 0,
+ .dev = {
+ .platform_data = &vulcan_sram_data,
+ },
+ .resource = &vulcan_sram_resource,
+ .num_resources = 1,
+};
+
+static struct resource vulcan_uart_resources[] = {
+ [0] = {
+ .start = IXP4XX_UART1_BASE_PHYS,
+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IXP4XX_UART2_BASE_PHYS,
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct plat_serial8250_port vulcan_uart_data[] = {
+ [0] = {
+ .mapbase = IXP4XX_UART1_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART1,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ [1] = {
+ .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART2,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ [2] = {
+ .irq = IXP4XX_GPIO_IRQ(4),
+ .irqflags = IRQF_TRIGGER_LOW,
+ .flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .uartclk = 1843200,
+ },
+ [3] = {
+ .irq = IXP4XX_GPIO_IRQ(4),
+ .irqflags = IRQF_TRIGGER_LOW,
+ .flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .uartclk = 1843200,
+ },
+ { }
+};
+
+static struct platform_device vulcan_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = vulcan_uart_data,
+ },
+ .resource = vulcan_uart_resources,
+ .num_resources = ARRAY_SIZE(vulcan_uart_resources),
+};
+
+static struct eth_plat_info vulcan_plat_eth[] = {
+ [0] = {
+ .phy = 0,
+ .rxq = 3,
+ .txreadyq = 20,
+ },
+ [1] = {
+ .phy = 1,
+ .rxq = 4,
+ .txreadyq = 21,
+ },
+};
+
+static struct platform_device vulcan_eth[] = {
+ [0] = {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev = {
+ .platform_data = &vulcan_plat_eth[0],
+ },
+ },
+ [1] = {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev = {
+ .platform_data = &vulcan_plat_eth[1],
+ },
+ },
+};
+
+static struct resource vulcan_max6369_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device vulcan_max6369 = {
+ .name = "max6369_wdt",
+ .id = -1,
+ .resource = &vulcan_max6369_resource,
+ .num_resources = 1,
+};
+
+static struct w1_gpio_platform_data vulcan_w1_gpio_pdata = {
+ .pin = 14,
+};
+
+static struct platform_device vulcan_w1_gpio = {
+ .name = "w1-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &vulcan_w1_gpio_pdata,
+ },
+};
+
+static struct platform_device *vulcan_devices[] __initdata = {
+ &vulcan_uart,
+ &vulcan_flash,
+ &vulcan_sram,
+ &vulcan_max6369,
+ &vulcan_eth[0],
+ &vulcan_eth[1],
+ &vulcan_w1_gpio,
+};
+
+static void __init vulcan_init(void)
+{
+ ixp4xx_sys_init();
+
+ /* Flash is spread over both CS0 and CS1 */
+ vulcan_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ vulcan_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+ *IXP4XX_EXP_CS0 = IXP4XX_EXP_BUS_CS_EN |
+ IXP4XX_EXP_BUS_STROBE_T(3) |
+ IXP4XX_EXP_BUS_SIZE(0xF) |
+ IXP4XX_EXP_BUS_BYTE_RD16 |
+ IXP4XX_EXP_BUS_WR_EN;
+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+ /* SRAM on CS2, (256kB, 8bit, writable) */
+ vulcan_sram_resource.start = IXP4XX_EXP_BUS_BASE(2);
+ vulcan_sram_resource.end = IXP4XX_EXP_BUS_BASE(2) + SZ_256K - 1;
+ *IXP4XX_EXP_CS2 = IXP4XX_EXP_BUS_CS_EN |
+ IXP4XX_EXP_BUS_STROBE_T(1) |
+ IXP4XX_EXP_BUS_HOLD_T(2) |
+ IXP4XX_EXP_BUS_SIZE(9) |
+ IXP4XX_EXP_BUS_SPLT_EN |
+ IXP4XX_EXP_BUS_WR_EN |
+ IXP4XX_EXP_BUS_BYTE_EN;
+
+ /* XR16L2551 on CS3 (Moto style, 512 bytes, 8bits, writable) */
+ vulcan_uart_resources[2].start = IXP4XX_EXP_BUS_BASE(3);
+ vulcan_uart_resources[2].end = IXP4XX_EXP_BUS_BASE(3) + 16 - 1;
+ vulcan_uart_data[2].mapbase = vulcan_uart_resources[2].start;
+ vulcan_uart_data[3].mapbase = vulcan_uart_data[2].mapbase + 8;
+ *IXP4XX_EXP_CS3 = IXP4XX_EXP_BUS_CS_EN |
+ IXP4XX_EXP_BUS_STROBE_T(3) |
+ IXP4XX_EXP_BUS_CYCLES(IXP4XX_EXP_BUS_CYCLES_MOTOROLA)|
+ IXP4XX_EXP_BUS_WR_EN |
+ IXP4XX_EXP_BUS_BYTE_EN;
+
+ /* GPIOS on CS4 (512 bytes, 8bits, writable) */
+ *IXP4XX_EXP_CS4 = IXP4XX_EXP_BUS_CS_EN |
+ IXP4XX_EXP_BUS_WR_EN |
+ IXP4XX_EXP_BUS_BYTE_EN;
+
+ /* max6369 on CS5 (512 bytes, 8bits, writable) */
+ vulcan_max6369_resource.start = IXP4XX_EXP_BUS_BASE(5);
+ vulcan_max6369_resource.end = IXP4XX_EXP_BUS_BASE(5);
+ *IXP4XX_EXP_CS5 = IXP4XX_EXP_BUS_CS_EN |
+ IXP4XX_EXP_BUS_WR_EN |
+ IXP4XX_EXP_BUS_BYTE_EN;
+
+ platform_add_devices(vulcan_devices, ARRAY_SIZE(vulcan_devices));
+}
+
+MACHINE_START(ARCOM_VULCAN, "Arcom/Eurotech Vulcan")
+ /* Maintainer: Marc Zyngier <maz@misterjones.org> */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = vulcan_init,
+MACHINE_END
diff --git a/drivers/crypto/ixp4xx_crypto.c b/drivers/crypto/ixp4xx_crypto.c
index f17ddf37a1e..0d662213c06 100644
--- a/drivers/crypto/ixp4xx_crypto.c
+++ b/drivers/crypto/ixp4xx_crypto.c
@@ -97,8 +97,13 @@
struct buffer_desc {
u32 phys_next;
+#ifdef __ARMEB__
u16 buf_len;
u16 pkt_len;
+#else
+ u16 pkt_len;
+ u16 buf_len;
+#endif
u32 phys_addr;
u32 __reserved[4];
struct buffer_desc *next;
@@ -106,17 +111,30 @@ struct buffer_desc {
};
struct crypt_ctl {
+#ifdef __ARMEB__
u8 mode; /* NPE_OP_* operation mode */
u8 init_len;
u16 reserved;
+#else
+ u16 reserved;
+ u8 init_len;
+ u8 mode; /* NPE_OP_* operation mode */
+#endif
u8 iv[MAX_IVLEN]; /* IV for CBC mode or CTR IV for CTR mode */
u32 icv_rev_aes; /* icv or rev aes */
u32 src_buf;
u32 dst_buf;
+#ifdef __ARMEB__
u16 auth_offs; /* Authentication start offset */
u16 auth_len; /* Authentication data length */
u16 crypt_offs; /* Cryption start offset */
u16 crypt_len; /* Cryption data length */
+#else
+ u16 auth_len; /* Authentication data length */
+ u16 auth_offs; /* Authentication start offset */
+ u16 crypt_len; /* Cryption data length */
+ u16 crypt_offs; /* Cryption start offset */
+#endif
u32 aadAddr; /* Additional Auth Data Addr for CCM mode */
u32 crypto_ctx; /* NPE Crypto Param structure address */
@@ -652,6 +670,9 @@ static int setup_auth(struct crypto_tfm *tfm, int encrypt, unsigned authsize,
/* write cfg word to cryptinfo */
cfgword = algo->cfgword | ( authsize << 6); /* (authsize/4) << 8 */
+#ifndef __ARMEB__
+ cfgword ^= 0xAA000000; /* change the "byte swap" flags */
+#endif
*(u32*)cinfo = cpu_to_be32(cfgword);
cinfo += sizeof(cfgword);
diff --git a/drivers/net/arm/ixp4xx_eth.c b/drivers/net/arm/ixp4xx_eth.c
index 4f1cc7164ad..6028226a727 100644
--- a/drivers/net/arm/ixp4xx_eth.c
+++ b/drivers/net/arm/ixp4xx_eth.c
@@ -241,7 +241,7 @@ static inline void memcpy_swab32(u32 *dest, u32 *src, int cnt)
static spinlock_t mdio_lock;
static struct eth_regs __iomem *mdio_regs; /* mdio command and status only */
-struct mii_bus *mdio_bus;
+static struct mii_bus *mdio_bus;
static int ports_open;
static struct port *npe_port_tab[MAX_NPES];
static struct dma_pool *dma_pool;
diff --git a/drivers/net/wan/ixp4xx_hss.c b/drivers/net/wan/ixp4xx_hss.c
index 88e363033e2..6c571e19883 100644
--- a/drivers/net/wan/ixp4xx_hss.c
+++ b/drivers/net/wan/ixp4xx_hss.c
@@ -396,7 +396,7 @@ static void hss_config(struct port *port)
msg.cmd = PORT_CONFIG_WRITE;
msg.hss_port = port->id;
msg.index = HSS_CONFIG_TX_PCR;
- msg.data32 = PCR_FRM_SYNC_OUTPUT_RISING | PCR_MSB_ENDIAN |
+ msg.data32 = PCR_FRM_PULSE_DISABLED | PCR_MSB_ENDIAN |
PCR_TX_DATA_ENABLE | PCR_SOF_NO_FBIT;
if (port->clock_type == CLOCK_INT)
msg.data32 |= PCR_SYNC_CLK_DIR_OUTPUT;