diff options
| -rw-r--r-- | Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt | 15 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/vendor-prefixes.txt | 1 | ||||
| -rw-r--r-- | arch/arm/boot/dts/integratorap.dts | 41 | ||||
| -rw-r--r-- | arch/arm/mach-integrator/integrator_ap.c | 11 | ||||
| -rw-r--r-- | arch/arm/mach-integrator/pci_v3.c | 177 |
5 files changed, 209 insertions, 36 deletions
diff --git a/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt b/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt new file mode 100644 index 00000000000..30b364e504b --- /dev/null +++ b/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt @@ -0,0 +1,15 @@ +V3 Semiconductor V360 EPC PCI bridge + +This bridge is found in the ARM Integrator/AP (Application Platform) + +Integrator-specific notes: + +- syscon: should contain a link to the syscon device node (since + on the Integrator, some registers in the syscon are required to + operate the V3). + +V360 EPC specific notes: + +- reg: should contain the base address of the V3 adapter. +- interrupts: should contain a reference to the V3 error interrupt + as routed on the system. diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 6931c4348d2..d247d100398 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -59,6 +59,7 @@ ste ST-Ericsson stericsson ST-Ericsson ti Texas Instruments toshiba Toshiba Corporation +v3 V3 Semiconductor via VIA Technologies, Inc. wlf Wolfson Microelectronics wm Wondermedia Technologies, Inc. diff --git a/arch/arm/boot/dts/integratorap.dts b/arch/arm/boot/dts/integratorap.dts index c9c3fa34464..03f23b7a0ab 100644 --- a/arch/arm/boot/dts/integratorap.dts +++ b/arch/arm/boot/dts/integratorap.dts @@ -39,6 +39,47 @@ valid-mask = <0x003fffff>; }; + pci: pciv3@62000000 { + compatible = "v3,v360epc-pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0x62000000 0x10000>; + interrupt-parent = <&pic>; + interrupts = <17>; /* Bus error IRQ */ + ranges = <0x00000000 0 0x61000000 /* config space */ + 0x61000000 0 0x00100000 /* 16 MiB @ 61000000 */ + 0x01000000 0 0x60000000 /* I/O space */ + 0x60000000 0 0x00100000 /* 16 MiB @ 60000000 */ + 0x02000000 0 0x40000000 /* non-prefectable memory */ + 0x40000000 0 0x10000000 /* 256 MiB @ 40000000 */ + 0x42000000 0 0x50000000 /* prefetchable memory */ + 0x50000000 0 0x10000000>; /* 256 MiB @ 50000000 */ + interrupt-map-mask = <0xf800 0 0 0x7>; + interrupt-map = < + /* IDSEL 9 */ + 0x4800 0 0 1 &pic 13 /* INT A on slot 9 is irq 13 */ + 0x4800 0 0 2 &pic 14 /* INT B on slot 9 is irq 14 */ + 0x4800 0 0 3 &pic 15 /* INT C on slot 9 is irq 15 */ + 0x4800 0 0 4 &pic 16 /* INT D on slot 9 is irq 16 */ + /* IDSEL 10 */ + 0x5000 0 0 1 &pic 14 /* INT A on slot 10 is irq 14 */ + 0x5000 0 0 2 &pic 15 /* INT B on slot 10 is irq 15 */ + 0x5000 0 0 3 &pic 16 /* INT C on slot 10 is irq 16 */ + 0x5000 0 0 4 &pic 13 /* INT D on slot 10 is irq 13 */ + /* IDSEL 11 */ + 0x5800 0 0 1 &pic 15 /* INT A on slot 11 is irq 15 */ + 0x5800 0 0 2 &pic 16 /* INT B on slot 11 is irq 16 */ + 0x5800 0 0 3 &pic 13 /* INT C on slot 11 is irq 13 */ + 0x5800 0 0 4 &pic 14 /* INT D on slot 11 is irq 14 */ + /* IDSEL 12 */ + 0x6000 0 0 1 &pic 16 /* INT A on slot 12 is irq 16 */ + 0x6000 0 0 2 &pic 13 /* INT B on slot 12 is irq 13 */ + 0x6000 0 0 3 &pic 14 /* INT C on slot 12 is irq 14 */ + 0x6000 0 0 4 &pic 15 /* INT D on slot 12 is irq 15 */ + >; + }; + fpga { /* * The Integator/AP predates the idea to have magic numbers diff --git a/arch/arm/mach-integrator/integrator_ap.c b/arch/arm/mach-integrator/integrator_ap.c index 16f3196efdb..a5b15c4e8de 100644 --- a/arch/arm/mach-integrator/integrator_ap.c +++ b/arch/arm/mach-integrator/integrator_ap.c @@ -473,15 +473,6 @@ static struct of_dev_auxdata ap_auxdata_lookup[] __initdata = { { /* sentinel */ }, }; -/* - * This is a placeholder that will get deleted when we move the PCI - * device over to the device tree. - */ -static struct platform_device pci_v3_device_of = { - .name = "pci-v3", - .id = 0, -}; - static void __init ap_init_of(void) { unsigned long sc_dec; @@ -536,8 +527,6 @@ static void __init ap_init_of(void) of_platform_populate(root, of_default_bus_match_table, ap_auxdata_lookup, parent); - platform_device_register(&pci_v3_device_of); - sc_dec = readl(ap_syscon_base + INTEGRATOR_SC_DEC_OFFSET); for (i = 0; i < 4; i++) { struct lm_device *lmdev; diff --git a/arch/arm/mach-integrator/pci_v3.c b/arch/arm/mach-integrator/pci_v3.c index a3cefdebd13..a0e069d37e1 100644 --- a/arch/arm/mach-integrator/pci_v3.c +++ b/arch/arm/mach-integrator/pci_v3.c @@ -28,6 +28,10 @@ #include <linux/init.h> #include <linux/io.h> #include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> +#include <linux/of_pci.h> #include <video/vga.h> #include <mach/hardware.h> @@ -279,7 +283,12 @@ * the mappings into PCI memory. */ +/* Filled in by probe */ static void __iomem *pci_v3_base; +static struct resource conf_mem; /* FIXME: remap this instead of static map */ +static struct resource io_mem; +static struct resource non_mem; +static struct resource pre_mem; // V3 access routines #define v3_writeb(o,v) __raw_writeb(v, pci_v3_base + (unsigned int)(o)) @@ -423,13 +432,13 @@ static void __iomem *v3_open_config_window(struct pci_bus *bus, * prefetchable), this frees up base1 for re-use by * configuration memory */ - v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE) | + v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(non_mem.start) | V3_LB_BASE_ADR_SIZE_512MB | V3_LB_BASE_ENABLE); /* * Set up base1/map1 to point into configuration space. */ - v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(PHYS_PCI_CONFIG_BASE) | + v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(conf_mem.start) | V3_LB_BASE_ADR_SIZE_16MB | V3_LB_BASE_ENABLE); v3_writew(V3_LB_MAP1, mapaddress); @@ -441,7 +450,7 @@ static void v3_close_config_window(void) /* * Reassign base1 for use by prefetchable PCI memory */ - v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE + SZ_256M) | + v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(pre_mem.start) | V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_PREFETCH | V3_LB_BASE_ENABLE); v3_writew(V3_LB_MAP1, v3_addr_to_lb_map(PCI_BUS_PREMEM_START) | @@ -450,7 +459,7 @@ static void v3_close_config_window(void) /* * And shrink base0 back to a 256M window (NOTE: MAP0 already correct) */ - v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE) | + v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(non_mem.start) | V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_ENABLE); } @@ -522,20 +531,6 @@ static struct pci_ops pci_v3_ops = { .write = v3_write_config, }; -static struct resource non_mem = { - .name = "PCI non-prefetchable", - .start = PHYS_PCI_MEM_BASE + PCI_BUS_NONMEM_START, - .end = PHYS_PCI_MEM_BASE + PCI_BUS_NONMEM_START + PCI_BUS_NONMEM_SIZE - 1, - .flags = IORESOURCE_MEM, -}; - -static struct resource pre_mem = { - .name = "PCI prefetchable", - .start = PHYS_PCI_MEM_BASE + PCI_BUS_PREMEM_START, - .end = PHYS_PCI_MEM_BASE + PCI_BUS_PREMEM_START + PCI_BUS_PREMEM_SIZE - 1, - .flags = IORESOURCE_MEM | IORESOURCE_PREFETCH, -}; - static int __init pci_v3_setup_resources(struct pci_sys_data *sys) { if (request_resource(&iomem_resource, &non_mem)) { @@ -659,7 +654,7 @@ static int __init pci_v3_setup(int nr, struct pci_sys_data *sys) return -EINVAL; if (nr == 0) { - sys->mem_offset = PHYS_PCI_MEM_BASE; + sys->mem_offset = non_mem.start; ret = pci_v3_setup_resources(sys); } @@ -697,7 +692,7 @@ static void __init pci_v3_preinit(void) * Setup window 0 - PCI non-prefetchable memory * Local: 0x40000000 Bus: 0x00000000 Size: 256MB */ - v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE) | + v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(non_mem.start) | V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_ENABLE); v3_writew(V3_LB_MAP0, v3_addr_to_lb_map(PCI_BUS_NONMEM_START) | V3_LB_MAP_TYPE_MEM); @@ -706,7 +701,7 @@ static void __init pci_v3_preinit(void) * Setup window 1 - PCI prefetchable memory * Local: 0x50000000 Bus: 0x10000000 Size: 256MB */ - v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE + SZ_256M) | + v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(pre_mem.start) | V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_PREFETCH | V3_LB_BASE_ENABLE); v3_writew(V3_LB_MAP1, v3_addr_to_lb_map(PCI_BUS_PREMEM_START) | @@ -715,7 +710,7 @@ static void __init pci_v3_preinit(void) /* * Setup window 2 - PCI IO */ - v3_writel(V3_LB_BASE2, v3_addr_to_lb_base2(PHYS_PCI_IO_BASE) | + v3_writel(V3_LB_BASE2, v3_addr_to_lb_base2(io_mem.start) | V3_LB_BASE_ENABLE); v3_writew(V3_LB_MAP2, v3_addr_to_lb_map2(0)); @@ -772,7 +767,7 @@ static void __init pci_v3_postinit(void) "interrupt: %d\n", ret); #endif - register_isa_ports(PHYS_PCI_MEM_BASE, PHYS_PCI_IO_BASE, 0); + register_isa_ports(non_mem.start, io_mem.start, 0); } /* @@ -837,7 +832,6 @@ static int __init pci_v3_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) static struct hw_pci pci_v3 __initdata = { .swizzle = pci_v3_swizzle, - .map_irq = pci_v3_map_irq, .setup = pci_v3_setup, .nr_controllers = 1, .ops = &pci_v3_ops, @@ -845,8 +839,107 @@ static struct hw_pci pci_v3 __initdata = { .postinit = pci_v3_postinit, }; +#ifdef CONFIG_OF + +static int __init pci_v3_map_irq_dt(const struct pci_dev *dev, u8 slot, u8 pin) +{ + struct of_irq oirq; + int ret; + + ret = of_irq_map_pci(dev, &oirq); + if (ret) { + dev_err(&dev->dev, "of_irq_map_pci() %d\n", ret); + /* Proper return code 0 == NO_IRQ */ + return 0; + } + + return irq_create_of_mapping(oirq.controller, oirq.specifier, + oirq.size); +} + +static int __init pci_v3_dtprobe(struct platform_device *pdev, + struct device_node *np) +{ + struct of_pci_range_parser parser; + struct of_pci_range range; + struct resource *res; + int irq, ret; + + if (of_pci_range_parser_init(&parser, np)) + return -EINVAL; + + /* Get base for bridge registers */ + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "unable to obtain PCIv3 base\n"); + return -ENODEV; + } + pci_v3_base = devm_ioremap(&pdev->dev, res->start, + resource_size(res)); + if (!pci_v3_base) { + dev_err(&pdev->dev, "unable to remap PCIv3 base\n"); + return -ENODEV; + } + + /* Get and request error IRQ resource */ + irq = platform_get_irq(pdev, 0); + if (irq <= 0) { + dev_err(&pdev->dev, "unable to obtain PCIv3 error IRQ\n"); + return -ENODEV; + } + ret = devm_request_irq(&pdev->dev, irq, v3_irq, 0, + "PCIv3 error", NULL); + if (ret < 0) { + dev_err(&pdev->dev, "unable to request PCIv3 error IRQ %d (%d)\n", irq, ret); + return ret; + } + + for_each_of_pci_range(&parser, &range) { + if (!range.flags) { + of_pci_range_to_resource(&range, np, &conf_mem); + conf_mem.name = "PCIv3 config"; + } + if (range.flags & IORESOURCE_IO) { + of_pci_range_to_resource(&range, np, &io_mem); + io_mem.name = "PCIv3 I/O"; + } + if ((range.flags & IORESOURCE_MEM) && + !(range.flags & IORESOURCE_PREFETCH)) { + of_pci_range_to_resource(&range, np, &non_mem); + non_mem.name = "PCIv3 non-prefetched mem"; + } + if ((range.flags & IORESOURCE_MEM) && + (range.flags & IORESOURCE_PREFETCH)) { + of_pci_range_to_resource(&range, np, &pre_mem); + pre_mem.name = "PCIv3 prefetched mem"; + } + } + + if (!conf_mem.start || !io_mem.start || + !non_mem.start || !pre_mem.start) { + dev_err(&pdev->dev, "missing ranges in device node\n"); + return -EINVAL; + } + + pci_v3.map_irq = pci_v3_map_irq_dt; + pci_common_init_dev(&pdev->dev, &pci_v3); + + return 0; +} + +#else + +static inline int pci_v3_dtprobe(struct platform_device *pdev, + struct device_node *np) +{ + return -EINVAL; +} + +#endif + static int __init pci_v3_probe(struct platform_device *pdev) { + struct device_node *np = pdev->dev.of_node; int ret; /* Remap the Integrator system controller */ @@ -856,6 +949,10 @@ static int __init pci_v3_probe(struct platform_device *pdev) return -ENODEV; } + /* Device tree probe path */ + if (np) + return pci_v3_dtprobe(pdev, np); + pci_v3_base = devm_ioremap(&pdev->dev, PHYS_PCI_V3_BASE, SZ_64K); if (!pci_v3_base) { dev_err(&pdev->dev, "unable to remap PCIv3 base\n"); @@ -869,14 +966,44 @@ static int __init pci_v3_probe(struct platform_device *pdev) return -ENODEV; } - pci_common_init(&pci_v3); + conf_mem.name = "PCIv3 config"; + conf_mem.start = PHYS_PCI_CONFIG_BASE; + conf_mem.end = PHYS_PCI_CONFIG_BASE + SZ_16M - 1; + conf_mem.flags = IORESOURCE_MEM; + + io_mem.name = "PCIv3 I/O"; + io_mem.start = PHYS_PCI_IO_BASE; + io_mem.end = PHYS_PCI_IO_BASE + SZ_16M - 1; + io_mem.flags = IORESOURCE_MEM; + + non_mem.name = "PCIv3 non-prefetched mem"; + non_mem.start = PHYS_PCI_MEM_BASE + PCI_BUS_NONMEM_START; + non_mem.end = PHYS_PCI_MEM_BASE + PCI_BUS_NONMEM_START + + PCI_BUS_NONMEM_SIZE - 1; + non_mem.flags = IORESOURCE_MEM; + + pre_mem.name = "PCIv3 prefetched mem"; + pre_mem.start = PHYS_PCI_MEM_BASE + PCI_BUS_PREMEM_START; + pre_mem.end = PHYS_PCI_MEM_BASE + PCI_BUS_PREMEM_START + + PCI_BUS_PREMEM_SIZE - 1; + pre_mem.flags = IORESOURCE_MEM | IORESOURCE_PREFETCH; + + pci_v3.map_irq = pci_v3_map_irq; + + pci_common_init_dev(&pdev->dev, &pci_v3); return 0; } +static const struct of_device_id pci_ids[] = { + { .compatible = "v3,v360epc-pci", }, + {}, +}; + static struct platform_driver pci_v3_driver = { .driver = { .name = "pci-v3", + .of_match_table = pci_ids, }, }; |