diff options
26 files changed, 633 insertions, 33 deletions
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index e968a52e488..58c74e737f7 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -224,6 +224,20 @@ choice Say Y here if you want kernel low-level debugging support on i.MX6Q UART4. + config DEBUG_MMP_UART2 + bool "Kernel low-level debugging message via MMP UART2" + depends on ARCH_MMP + help + Say Y here if you want kernel low-level debugging support + on MMP UART2. + + config DEBUG_MMP_UART3 + bool "Kernel low-level debugging message via MMP UART3" + depends on ARCH_MMP + help + Say Y here if you want kernel low-level debugging support + on MMP UART3. + config DEBUG_MSM_UART1 bool "Kernel low-level debugging messages via MSM UART1" depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50 diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts index 0c49caa0997..d69a7999a12 100644 --- a/arch/arm/boot/dts/exynos4210-origen.dts +++ b/arch/arm/boot/dts/exynos4210-origen.dts @@ -62,35 +62,43 @@ up { label = "Up"; - gpios = <&gpx2 0 0 0 2>; + gpios = <&gpx2 0 0 0x10000 2>; linux,code = <103>; }; down { label = "Down"; - gpios = <&gpx2 1 0 0 2>; + gpios = <&gpx2 1 0 0x10000 2>; linux,code = <108>; }; back { label = "Back"; - gpios = <&gpx1 7 0 0 2>; + gpios = <&gpx1 7 0 0x10000 2>; linux,code = <158>; }; home { label = "Home"; - gpios = <&gpx1 6 0 0 2>; + gpios = <&gpx1 6 0 0x10000 2>; linux,code = <102>; }; menu { label = "Menu"; - gpios = <&gpx1 5 0 0 2>; + gpios = <&gpx1 5 0 0x10000 2>; linux,code = <139>; }; }; + leds { + compatible = "gpio-leds"; + status { + gpios = <&gpx1 3 0 0x10000 2>; + linux,default-trigger = "heartbeat"; + }; + }; + keypad@100A0000 { status = "disabled"; }; diff --git a/arch/arm/configs/armadillo800eva_defconfig b/arch/arm/configs/armadillo800eva_defconfig index 90610c7030f..f78d259f8d2 100644 --- a/arch/arm/configs/armadillo800eva_defconfig +++ b/arch/arm/configs/armadillo800eva_defconfig @@ -85,6 +85,7 @@ CONFIG_SERIAL_SH_SCI_NR_UARTS=8 CONFIG_SERIAL_SH_SCI_CONSOLE=y # CONFIG_HW_RANDOM is not set CONFIG_I2C=y +CONFIG_I2C_GPIO=y CONFIG_I2C_SH_MOBILE=y # CONFIG_HWMON is not set CONFIG_MEDIA_SUPPORT=y @@ -120,6 +121,8 @@ CONFIG_USB_ETH=m CONFIG_MMC=y CONFIG_MMC_SDHI=y CONFIG_MMC_SH_MMCIF=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_S35390A=y CONFIG_DMADEVICES=y CONFIG_SH_DMAE=y CONFIG_UIO=y diff --git a/arch/arm/configs/marzen_defconfig b/arch/arm/configs/marzen_defconfig index 864f9a5c39d..f513acedc10 100644 --- a/arch/arm/configs/marzen_defconfig +++ b/arch/arm/configs/marzen_defconfig @@ -68,6 +68,8 @@ CONFIG_SERIAL_SH_SCI_CONSOLE=y # CONFIG_HW_RANDOM is not set CONFIG_GPIO_SYSFS=y # CONFIG_HWMON is not set +CONFIG_THERMAL=y +CONFIG_RCAR_THERMAL=y CONFIG_SSB=y # CONFIG_HID_SUPPORT is not set # CONFIG_USB_SUPPORT is not set diff --git a/arch/arm/configs/mmp2_defconfig b/arch/arm/configs/mmp2_defconfig index 5a584520db2..f1cb95e58af 100644 --- a/arch/arm/configs/mmp2_defconfig +++ b/arch/arm/configs/mmp2_defconfig @@ -16,7 +16,7 @@ CONFIG_PREEMPT=y CONFIG_AEABI=y CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 -CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS2,38400 mem=128M user_debug=255" +CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS2,38400 mem=128M user_debug=255 earlyprintk" CONFIG_VFP=y CONFIG_NET=y CONFIG_PACKET=y @@ -90,6 +90,9 @@ CONFIG_DEBUG_INFO=y # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_DYNAMIC_DEBUG is not set CONFIG_DEBUG_USER=y +CONFIG_DEBUG_LL=y +CONFIG_DEBUG_MMP_UART3=y +CONFIG_EARLY_PRINTK=y CONFIG_DEBUG_ERRORS=y # CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRC_CCITT=y diff --git a/arch/arm/configs/pxa910_defconfig b/arch/arm/configs/pxa910_defconfig index 1cd381e1d47..191118caa5c 100644 --- a/arch/arm/configs/pxa910_defconfig +++ b/arch/arm/configs/pxa910_defconfig @@ -17,7 +17,7 @@ CONFIG_PREEMPT=y CONFIG_AEABI=y CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 -CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.2.100:/nfsroot/ ip=192.168.2.101:192.168.2.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=128M" +CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.2.100:/nfsroot/ ip=192.168.2.101:192.168.2.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=128M earlyprintk" CONFIG_FPE_NWFPE=y CONFIG_NET=y CONFIG_PACKET=y @@ -66,5 +66,7 @@ CONFIG_DEBUG_INFO=y CONFIG_DEBUG_USER=y CONFIG_DEBUG_ERRORS=y CONFIG_DEBUG_LL=y +CONFIG_DEBUG_MMP_UART2=y +CONFIG_EARLY_PRINTK=y # CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRC_CCITT=y diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index 412884dafa6..4372075c551 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -221,6 +221,7 @@ config MACH_SMDKV310 select EXYNOS4_SETUP_KEYPAD select EXYNOS4_SETUP_SDHCI select EXYNOS4_SETUP_USB_PHY + select S3C24XX_PWM help Machine support for Samsung SMDKV310 @@ -348,6 +349,7 @@ config MACH_ORIGEN select EXYNOS4_SETUP_FIMD0 select EXYNOS4_SETUP_SDHCI select EXYNOS4_SETUP_USB_PHY + select S3C24XX_PWM help Machine support for ORIGEN based on Samsung EXYNOS4210 @@ -383,6 +385,7 @@ config MACH_SMDK4212 select EXYNOS4_SETUP_KEYPAD select EXYNOS4_SETUP_SDHCI select EXYNOS4_SETUP_USB_PHY + select S3C24XX_PWM help Machine support for Samsung SMDK4212 diff --git a/arch/arm/mach-exynos/mach-origen.c b/arch/arm/mach-exynos/mach-origen.c index 4e574c24581..b45600fcf73 100644 --- a/arch/arm/mach-exynos/mach-origen.c +++ b/arch/arm/mach-exynos/mach-origen.c @@ -15,6 +15,7 @@ #include <linux/platform_device.h> #include <linux/io.h> #include <linux/input.h> +#include <linux/pwm.h> #include <linux/pwm_backlight.h> #include <linux/gpio_keys.h> #include <linux/i2c.h> @@ -614,6 +615,10 @@ static struct platform_device origen_lcd_hv070wsa = { .dev.platform_data = &origen_lcd_hv070wsa_data, }; +static struct pwm_lookup origen_pwm_lookup[] = { + PWM_LOOKUP("s3c24xx-pwm.0", 0, "pwm-backlight.0", NULL), +}; + #ifdef CONFIG_DRM_EXYNOS static struct exynos_drm_fimd_pdata drm_fimd_pdata = { .panel = { @@ -798,6 +803,7 @@ static void __init origen_machine_init(void) platform_add_devices(origen_devices, ARRAY_SIZE(origen_devices)); + pwm_add_table(origen_pwm_lookup, ARRAY_SIZE(origen_pwm_lookup)); samsung_bl_set(&origen_bl_gpio_info, &origen_bl_data); origen_bt_setup(); diff --git a/arch/arm/mach-exynos/mach-smdk4x12.c b/arch/arm/mach-exynos/mach-smdk4x12.c index b26beb13ebe..81bf59c6f4b 100644 --- a/arch/arm/mach-exynos/mach-smdk4x12.c +++ b/arch/arm/mach-exynos/mach-smdk4x12.c @@ -17,6 +17,7 @@ #include <linux/mfd/max8997.h> #include <linux/mmc/host.h> #include <linux/platform_device.h> +#include <linux/pwm.h> #include <linux/pwm_backlight.h> #include <linux/regulator/machine.h> #include <linux/serial_core.h> @@ -222,6 +223,10 @@ static struct platform_pwm_backlight_data smdk4x12_bl_data = { .pwm_period_ns = 1000, }; +static struct pwm_lookup smdk4x12_pwm_lookup[] = { + PWM_LOOKUP("s3c24xx-pwm.1", 0, "pwm-backlight.0", NULL), +}; + static uint32_t smdk4x12_keymap[] __initdata = { /* KEY(row, col, keycode) */ KEY(1, 3, KEY_1), KEY(1, 4, KEY_2), KEY(1, 5, KEY_3), @@ -349,6 +354,7 @@ static void __init smdk4x12_machine_init(void) ARRAY_SIZE(smdk4x12_i2c_devs7)); samsung_bl_set(&smdk4x12_bl_gpio_info, &smdk4x12_bl_data); + pwm_add_table(smdk4x12_pwm_lookup, ARRAY_SIZE(smdk4x12_pwm_lookup)); samsung_keypad_set_platdata(&smdk4x12_keypad_data); diff --git a/arch/arm/mach-exynos/mach-smdkv310.c b/arch/arm/mach-exynos/mach-smdkv310.c index 73f2bce097e..12a1db29e1a 100644 --- a/arch/arm/mach-exynos/mach-smdkv310.c +++ b/arch/arm/mach-exynos/mach-smdkv310.c @@ -18,6 +18,7 @@ #include <linux/io.h> #include <linux/i2c.h> #include <linux/input.h> +#include <linux/pwm.h> #include <linux/pwm_backlight.h> #include <linux/platform_data/s3c-hsotg.h> @@ -360,6 +361,10 @@ static struct i2c_board_info hdmiphy_info = { I2C_BOARD_INFO("hdmiphy-exynos4210", 0x38), }; +static struct pwm_lookup smdkv310_pwm_lookup[] = { + PWM_LOOKUP("s3c24xx-pwm.1", 0, "pwm-backlight.0", NULL), +}; + static void s5p_tv_setup(void) { /* direct HPD to HDMI chip */ @@ -399,6 +404,8 @@ static void __init smdkv310_machine_init(void) samsung_keypad_set_platdata(&smdkv310_keypad_data); samsung_bl_set(&smdkv310_bl_gpio_info, &smdkv310_bl_data); + pwm_add_table(smdkv310_pwm_lookup, ARRAY_SIZE(smdkv310_pwm_lookup)); + #ifdef CONFIG_DRM_EXYNOS s5p_device_fimd0.dev.platform_data = &drm_fimd_pdata; exynos4_fimd0_gpio_setup_24bpp(); diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index 7ca5fe45945..3a2042fb971 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -298,6 +298,7 @@ config MACH_MX27_3DS select IMX_HAVE_PLATFORM_IMX_FB select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_KEYPAD + select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MX2_CAMERA select IMX_HAVE_PLATFORM_MXC_EHCI diff --git a/arch/arm/mach-imx/mach-mx27_3ds.c b/arch/arm/mach-imx/mach-mx27_3ds.c index 58c24c1a7ab..05996f39005 100644 --- a/arch/arm/mach-imx/mach-mx27_3ds.c +++ b/arch/arm/mach-imx/mach-mx27_3ds.c @@ -158,6 +158,11 @@ static const int mx27pdk_pins[] __initconst = { PB21_PF_CSI_HSYNC, CSI_PWRDWN | GPIO_GPIO | GPIO_OUT, CSI_RESET | GPIO_GPIO | GPIO_OUT, + /* SSI4 */ + PC16_PF_SSI4_FS, + PC17_PF_SSI4_RXD, + PC18_PF_SSI4_TXD, + PC19_PF_SSI4_CLK, }; static struct gpio mx27_3ds_camera_gpios[] = { @@ -329,13 +334,24 @@ static struct mc13xxx_regulator_init_data mx27_3ds_regulators[] = { }; /* MC13783 */ +static struct mc13xxx_codec_platform_data mx27_3ds_codec = { + .dac_ssi_port = MC13783_SSI1_PORT, + .adc_ssi_port = MC13783_SSI1_PORT, +}; + static struct mc13xxx_platform_data mc13783_pdata = { .regulators = { .regulators = mx27_3ds_regulators, .num_regulators = ARRAY_SIZE(mx27_3ds_regulators), }, - .flags = MC13XXX_USE_TOUCHSCREEN | MC13XXX_USE_RTC, + .flags = MC13XXX_USE_TOUCHSCREEN | MC13XXX_USE_RTC | + MC13XXX_USE_CODEC, + .codec = &mx27_3ds_codec, +}; + +static struct imx_ssi_platform_data mx27_3ds_ssi_pdata = { + .flags = IMX_SSI_DMA | IMX_SSI_NET, }; /* SPI */ @@ -512,6 +528,9 @@ static void __init mx27pdk_init(void) } imx27_add_mx2_camera(&mx27_3ds_cam_pdata); + imx27_add_imx_ssi(0, &mx27_3ds_ssi_pdata); + + imx_add_platform_device("imx_mc13783", 0, NULL, 0, NULL, 0); } static void __init mx27pdk_timer_init(void) diff --git a/arch/arm/mach-ks8695/Kconfig b/arch/arm/mach-ks8695/Kconfig index f5c39a8c2b0..a545976bdbd 100644 --- a/arch/arm/mach-ks8695/Kconfig +++ b/arch/arm/mach-ks8695/Kconfig @@ -21,6 +21,67 @@ config MACH_ACS5K say 'Y' here if you want your kernel to run on the Brivo Systems LLC, ACS-5000 Master board. +config MACH_LITE300 + bool "SecureComputing SG300" + help + Say 'Y' here if you want your kernel to support the + SecureComputing / SnapGear SG300 VPN Internet Router. + See http://www.securecomputing.com for more details. + +config MACH_SG310 + bool "McAfee SG310" + help + Say 'Y' here if you want your kernel to support the + McAfee / SnapGear SG310 VPN Internet Router. + See http://www.mcafee.com for more details. + +config MACH_SE4200 + bool "SecureComputing SE4200" + help + Say 'Y' here if you want your kernel to support the + SecureComputing / SnapGear SE4200 Secure Wireless VPN + Internet Router. + See http://www.securecomputing.com for more details. + +config MACH_CM4002 + bool "OpenGear CM4002" + help + Say 'Y' here if you want your kernel to support the OpenGear + CM4002 Secure Access Server. See http://www.opengear.com for + more details. + +config MACH_CM4008 + bool "OpenGear CM4008" + select MIGHT_HAVE_PCI + help + Say 'Y' here if you want your kernel to support the OpenGear + CM4008 Console Server. See http://www.opengear.com for more + details. + +config MACH_CM41xx + bool "OpenGear CM41xx" + select MIGHT_HAVE_PCI + help + Say 'Y' here if you want your kernel to support the OpenGear + CM4016 or CM4048 Console Servers. See http://www.opengear.com for + more details. + +config MACH_IM4004 + bool "OpenGear IM4004" + select MIGHT_HAVE_PCI + help + Say 'Y' here if you want your kernel to support the OpenGear + IM4004 Secure Access Server. See http://www.opengear.com for + more details. + +config MACH_IM42xx + bool "OpenGear IM42xx" + select MIGHT_HAVE_PCI + help + Say 'Y' here if you want your kernel to support the OpenGear + IM4216 or IM4248 Console Servers. See http://www.opengear.com for + more details. + endmenu endif diff --git a/arch/arm/mach-ks8695/Makefile b/arch/arm/mach-ks8695/Makefile index 9324ef965c2..e370caf0c91 100644 --- a/arch/arm/mach-ks8695/Makefile +++ b/arch/arm/mach-ks8695/Makefile @@ -15,3 +15,11 @@ obj-$(CONFIG_PCI) += pci.o obj-$(CONFIG_MACH_KS8695) += board-micrel.o obj-$(CONFIG_MACH_DSM320) += board-dsm320.o obj-$(CONFIG_MACH_ACS5K) += board-acs5k.o +obj-$(CONFIG_MACH_LITE300) += board-sg.o +obj-$(CONFIG_MACH_SG310) += board-sg.o +obj-$(CONFIG_MACH_SE4200) += board-sg.o +obj-$(CONFIG_MACH_CM4002) += board-og.o +obj-$(CONFIG_MACH_CM4008) += board-og.o +obj-$(CONFIG_MACH_CM41xx) += board-og.o +obj-$(CONFIG_MACH_IM4004) += board-og.o +obj-$(CONFIG_MACH_IM42xx) += board-og.o diff --git a/arch/arm/mach-ks8695/board-og.c b/arch/arm/mach-ks8695/board-og.c new file mode 100644 index 00000000000..1623ba461e4 --- /dev/null +++ b/arch/arm/mach-ks8695/board-og.c @@ -0,0 +1,199 @@ +/* + * board-og.c -- support for the OpenGear KS8695 based boards. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/platform_device.h> +#include <linux/serial_8250.h> +#include <linux/gpio.h> +#include <linux/irq.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <mach/devices.h> +#include <mach/regs-gpio.h> +#include <mach/gpio-ks8695.h> +#include "generic.h" + +static int og_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) +{ + if (machine_is_im4004() && (slot == 8)) + return KS8695_IRQ_EXTERN1; + return KS8695_IRQ_EXTERN0; +} + +static struct ks8695_pci_cfg __initdata og_pci = { + .mode = KS8695_MODE_PCI, + .map_irq = og_pci_map_irq, +}; + +static void __init og_register_pci(void) +{ + /* Initialize the GPIO lines for interrupt mode */ + ks8695_gpio_interrupt(KS8695_GPIO_0, IRQ_TYPE_LEVEL_LOW); + + /* Cardbus Slot */ + if (machine_is_im4004()) + ks8695_gpio_interrupt(KS8695_GPIO_1, IRQ_TYPE_LEVEL_LOW); + + ks8695_init_pci(&og_pci); +} + +/* + * The PCI bus reset is driven by a dedicated GPIO line. Toggle it here + * and bring the PCI bus out of reset. + */ +static void __init og_pci_bus_reset(void) +{ + unsigned int rstline = 1; + + /* Some boards use a different GPIO as the PCI reset line */ + if (machine_is_im4004()) + rstline = 2; + else if (machine_is_im42xx()) + rstline = 0; + + gpio_request(rstline, "PCI reset"); + gpio_direction_output(rstline, 0); + + /* Drive a reset on the PCI reset line */ + gpio_set_value(rstline, 1); + gpio_set_value(rstline, 0); + mdelay(100); + gpio_set_value(rstline, 1); + mdelay(100); +} + +/* + * Direct connect serial ports (non-PCI that is). + */ +#define S8250_PHYS 0x03800000 +#define S8250_VIRT 0xf4000000 +#define S8250_SIZE 0x00100000 + +static struct __initdata map_desc og_io_desc[] = { + { + .virtual = S8250_VIRT, + .pfn = __phys_to_pfn(S8250_PHYS), + .length = S8250_SIZE, + .type = MT_DEVICE, + } +}; + +static struct resource og_uart_resources[] = { + { + .start = S8250_VIRT, + .end = S8250_VIRT + S8250_SIZE, + .flags = IORESOURCE_MEM + }, +}; + +static struct plat_serial8250_port og_uart_data[] = { + { + .mapbase = S8250_VIRT, + .membase = (char *) S8250_VIRT, + .irq = 3, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = 115200 * 16, + }, + { }, +}; + +static struct platform_device og_uart = { + .name = "serial8250", + .id = 0, + .dev.platform_data = og_uart_data, + .num_resources = 1, + .resource = og_uart_resources +}; + +static struct platform_device *og_devices[] __initdata = { + &og_uart +}; + +static void __init og_init(void) +{ + ks8695_register_gpios(); + + if (machine_is_cm4002()) { + ks8695_gpio_interrupt(KS8695_GPIO_1, IRQ_TYPE_LEVEL_HIGH); + iotable_init(og_io_desc, ARRAY_SIZE(og_io_desc)); + platform_add_devices(og_devices, ARRAY_SIZE(og_devices)); + } else { + og_pci_bus_reset(); + og_register_pci(); + } + + ks8695_add_device_lan(); + ks8695_add_device_wan(); +} + +#ifdef CONFIG_MACH_CM4002 +MACHINE_START(CM4002, "OpenGear/CM4002") + /* OpenGear Inc. */ + .atag_offset = 0x100, + .map_io = ks8695_map_io, + .init_irq = ks8695_init_irq, + .init_machine = og_init, + .timer = &ks8695_timer, + .restart = ks8695_restart, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_CM4008 +MACHINE_START(CM4008, "OpenGear/CM4008") + /* OpenGear Inc. */ + .atag_offset = 0x100, + .map_io = ks8695_map_io, + .init_irq = ks8695_init_irq, + .init_machine = og_init, + .timer = &ks8695_timer, + .restart = ks8695_restart, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_CM41xx +MACHINE_START(CM41XX, "OpenGear/CM41xx") + /* OpenGear Inc. */ + .atag_offset = 0x100, + .map_io = ks8695_map_io, + .init_irq = ks8695_init_irq, + .init_machine = og_init, + .timer = &ks8695_timer, + .restart = ks8695_restart, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_IM4004 +MACHINE_START(IM4004, "OpenGear/IM4004") + /* OpenGear Inc. */ + .atag_offset = 0x100, + .map_io = ks8695_map_io, + .init_irq = ks8695_init_irq, + .init_machine = og_init, + .timer = &ks8695_timer, + .restart = ks8695_restart, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_IM42xx +MACHINE_START(IM42XX, "OpenGear/IM42xx") + /* OpenGear Inc. */ + .atag_offset = 0x100, + .map_io = ks8695_map_io, + .init_irq = ks8695_init_irq, + .init_machine = og_init, + .timer = &ks8695_timer, + .restart = ks8695_restart, +MACHINE_END +#endif diff --git a/arch/arm/mach-ks8695/board-sg.c b/arch/arm/mach-ks8695/board-sg.c new file mode 100644 index 00000000000..f35b98b5bf3 --- /dev/null +++ b/arch/arm/mach-ks8695/board-sg.c @@ -0,0 +1,121 @@ +/* + * board-sg.c -- support for the SnapGear KS8695 based boards + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/map.h> +#include <linux/mtd/physmap.h> +#include <linux/mtd/partitions.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <mach/devices.h> +#include "generic.h" + +/* + * The SG310 machine type is fitted with a conventional 8MB Strataflash + * device. Define its partitioning. + */ +#define FL_BASE 0x02000000 +#define FL_SIZE SZ_8M + +static struct mtd_partition sg_mtd_partitions[] = { + [0] = { + .name = "SnapGear Boot Loader", + .size = SZ_128K, + }, + [1] = { + .name = "SnapGear non-volatile configuration", + .size = SZ_512K, + .offset = SZ_256K, + }, + [2] = { + .name = "SnapGear image", + .offset = SZ_512K + SZ_256K, + }, + [3] = { + .name = "SnapGear StrataFlash", + }, + [4] = { + .name = "SnapGear Boot Tags", + .size = SZ_128K, + .offset = SZ_128K, + }, +}; + +static struct physmap_flash_data sg_mtd_pdata = { + .width = 1, + .nr_parts = ARRAY_SIZE(sg_mtd_partitions), + .parts = sg_mtd_partitions, +}; + + +static struct resource sg_mtd_resource[] = { + [0] = { + .start = FL_BASE, + .end = FL_BASE + FL_SIZE - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device sg_mtd_device = { + .name = "physmap-flash", + .id = 0, + .num_resources = ARRAY_SIZE(sg_mtd_resource), + .resource = sg_mtd_resource, + .dev = { + .platform_data = &sg_mtd_pdata, + }, +}; + +static void __init sg_init(void) +{ + ks8695_add_device_lan(); + ks8695_add_device_wan(); + + if (machine_is_sg310()) + platform_device_register(&sg_mtd_device); +} + +#ifdef CONFIG_MACH_LITE300 +MACHINE_START(LITE300, "SecureComputing/SG300") + /* SnapGear */ + .atag_offset = 0x100, + .map_io = ks8695_map_io, + .init_irq = ks8695_init_irq, + .init_machine = sg_init, + .timer = &ks8695_timer, + .restart = ks8695_restart, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_SG310 +MACHINE_START(SG310, "McAfee/SG310") + /* SnapGear */ + .atag_offset = 0x100, + .map_io = ks8695_map_io, + .init_irq = ks8695_init_irq, + .init_machine = sg_init, + .timer = &ks8695_timer, + .restart = ks8695_restart, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_SE4200 +MACHINE_START(SE4200, "SecureComputing/SE4200") + /* SnapGear */ + .atag_offset = 0x100, + .map_io = ks8695_map_io, + .init_irq = ks8695_init_irq, + .init_machine = sg_init, + .timer = &ks8695_timer, + .restart = ks8695_restart, +MACHINE_END +#endif diff --git a/arch/arm/mach-mmp/include/mach/debug-macro.S b/arch/arm/mach-mmp/include/mach/debug-macro.S index b6f14d203c2..5c3cc29688a 100644 --- a/arch/arm/mach-mmp/include/mach/debug-macro.S +++ b/arch/arm/mach-mmp/include/mach/debug-macro.S @@ -9,13 +9,21 @@ * published by the Free Software Foundation. */ +#if defined(CONFIG_DEBUG_MMP_UART2) +#define MMP_UART_OFFSET 0x00017000 +#elif defined(CONFIG_DEBUG_MMP_UART3) +#define MMP_UART_OFFSET 0x00018000 +#else +#error "Select uart for DEBUG_LL" +#endif + #include <mach/addr-map.h> .macro addruart, rp, rv, tmp ldr \rp, =APB_PHYS_BASE @ physical ldr \rv, =APB_VIRT_BASE @ virtual - orr \rp, \rp, #0x00017000 - orr \rv, \rv, #0x00017000 + orr \rp, \rp, #MMP_UART_OFFSET + orr \rv, \rv, #MMP_UART_OFFSET .endm #define UART_SHIFT 2 diff --git a/arch/arm/mach-mmp/ttc_dkb.c b/arch/arm/mach-mmp/ttc_dkb.c index 7a7de2b12a6..ce55fd8821c 100644 --- a/arch/arm/mach-mmp/ttc_dkb.c +++ b/arch/arm/mach-mmp/ttc_dkb.c @@ -177,12 +177,22 @@ static struct mv_usb_platform_data ttc_usb_pdata = { #endif #endif +#ifdef CONFIG_MTD_NAND_PXA3xx +static struct pxa3xx_nand_platform_data dkb_nand_info = { + .enable_arbiter = 1, + .num_cs = 1, +}; +#endif + static void __init ttc_dkb_init(void) { mfp_config(ARRAY_AND_SIZE(ttc_dkb_pin_config)); /* on-chip devices */ pxa910_add_uart(1); +#ifdef CONFIG_MTD_NAND_PXA3xx + pxa910_add_nand(&dkb_nand_info); +#endif /* off-chip devices */ pxa910_add_twsi(0, NULL, ARRAY_AND_SIZE(ttc_dkb_i2c_info)); diff --git a/arch/arm/mach-msm/Kconfig b/arch/arm/mach-msm/Kconfig index b2740c800e8..7902de151cc 100644 --- a/arch/arm/mach-msm/Kconfig +++ b/arch/arm/mach-msm/Kconfig @@ -1,8 +1,12 @@ if ARCH_MSM +comment "Qualcomm MSM SoC Type" + depends on (ARCH_MSM8X60 || ARCH_MSM8960) + choice prompt "Qualcomm MSM SoC Type" default ARCH_MSM7X00A + depends on !(ARCH_MSM8X60 || ARCH_MSM8960) config ARCH_MSM7X00A bool "MSM7x00A / MSM7x01A" @@ -36,6 +40,8 @@ config ARCH_QSD8X50 select GPIO_MSM_V1 select MSM_PROC_COMM +endchoice + config ARCH_MSM8X60 bool "MSM8X60" select ARCH_MSM_SCORPIONMP @@ -57,8 +63,6 @@ config ARCH_MSM8960 select MSM_SCM if SMP select USE_OF -endchoice - config MSM_HAS_DEBUG_UART_HS bool diff --git a/arch/arm/mach-msm/include/mach/msm_iomap-8x60.h b/arch/arm/mach-msm/include/mach/msm_iomap-8x60.h index c6d38f1d0c9..199372e62de 100644 --- a/arch/arm/mach-msm/include/mach/msm_iomap-8x60.h +++ b/arch/arm/mach-msm/include/mach/msm_iomap-8x60.h @@ -41,21 +41,10 @@ #define MSM8X60_QGIC_CPU_PHYS 0x02081000 #define MSM8X60_QGIC_CPU_SIZE SZ_4K -#define MSM_ACC_BASE IOMEM(0xF0002000) -#define MSM_ACC_PHYS 0x02001000 -#define MSM_ACC_SIZE SZ_4K - -#define MSM_GCC_BASE IOMEM(0xF0003000) -#define MSM_GCC_PHYS 0x02082000 -#define MSM_GCC_SIZE SZ_4K - #define MSM_TLMM_BASE IOMEM(0xF0004000) #define MSM_TLMM_PHYS 0x00800000 #define MSM_TLMM_SIZE SZ_16K -#define MSM_SHARED_RAM_BASE IOMEM(0xF0100000) -#define MSM_SHARED_RAM_SIZE SZ_1M - #define MSM8X60_TMR_PHYS 0x02000000 #define MSM8X60_TMR_SIZE SZ_4K diff --git a/arch/arm/mach-msm/include/mach/msm_iomap.h b/arch/arm/mach-msm/include/mach/msm_iomap.h index 00afdfb8c38..2ab7cf0919b 100644 --- a/arch/arm/mach-msm/include/mach/msm_iomap.h +++ b/arch/arm/mach-msm/include/mach/msm_iomap.h @@ -41,12 +41,11 @@ #include "msm_iomap-7x30.h" #elif defined(CONFIG_ARCH_QSD8X50) #include "msm_iomap-8x50.h" -#elif defined(CONFIG_ARCH_MSM8X60) -#include "msm_iomap-8x60.h" #else #include "msm_iomap-7x00.h" #endif +#include "msm_iomap-8x60.h" #include "msm_iomap-8960.h" #define MSM_DEBUG_UART_SIZE SZ_4K diff --git a/arch/arm/mach-msm/io.c b/arch/arm/mach-msm/io.c index 3854f6f20ce..123ef9cbce1 100644 --- a/arch/arm/mach-msm/io.c +++ b/arch/arm/mach-msm/io.c @@ -111,8 +111,6 @@ static struct map_desc msm8x60_io_desc[] __initdata = { MSM_CHIP_DEVICE(QGIC_CPU, MSM8X60), MSM_CHIP_DEVICE(TMR, MSM8X60), MSM_CHIP_DEVICE(TMR0, MSM8X60), - MSM_DEVICE(ACC), - MSM_DEVICE(GCC), #ifdef CONFIG_DEBUG_MSM8660_UART MSM_DEVICE(DEBUG_UART), #endif diff --git a/arch/arm/mach-s3c64xx/mach-crag6410-module.c b/arch/arm/mach-s3c64xx/mach-crag6410-module.c index 9e382e7c77c..7f4f9ebee25 100644 --- a/arch/arm/mach-s3c64xx/mach-crag6410-module.c +++ b/arch/arm/mach-s3c64xx/mach-crag6410-module.c @@ -16,6 +16,7 @@ #include <linux/mfd/wm831x/irq.h> #include <linux/mfd/wm831x/gpio.h> #include <linux/mfd/wm8994/pdata.h> +#include <linux/mfd/arizona/pdata.h> #include <linux/regulator/machine.h> @@ -181,9 +182,33 @@ static const struct i2c_board_info wm1277_devs[] = { }, }; -static const struct i2c_board_info wm5102_devs[] = { - { I2C_BOARD_INFO("wm5102", 0x1a), - .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2, }, +static struct arizona_pdata wm5102_pdata = { + .ldoena = S3C64XX_GPN(7), + .gpio_base = CODEC_GPIO_BASE, + .irq_active_high = true, + .micd_pol_gpio = CODEC_GPIO_BASE + 4, + .gpio_defaults = { + [2] = 0x10000, /* AIF3TXLRCLK */ + [3] = 0x4, /* OPCLK */ + }, +}; + +static struct s3c64xx_spi_csinfo wm5102_spi_csinfo = { + .line = S3C64XX_GPN(5), +}; + +static struct spi_board_info wm5102_spi_devs[] = { + [0] = { + .modalias = "wm5102", + .max_speed_hz = 10 * 1000 * 1000, + .bus_num = 0, + .chip_select = 0, + .mode = SPI_MODE_0, + .irq = GLENFARCLAS_PMIC_IRQ_BASE + + WM831X_IRQ_GPIO_2, + .controller_data = &wm5102_spi_csinfo, + .platform_data = &wm5102_pdata, + }, }; static const struct i2c_board_info wm6230_i2c_devs[] = { @@ -223,8 +248,9 @@ static __devinitdata const struct { { .id = 0x3c, .name = "1273-EV1 Longmorn" }, { .id = 0x3d, .name = "1277-EV1 Littlemill", .i2c_devs = wm1277_devs, .num_i2c_devs = ARRAY_SIZE(wm1277_devs) }, - { .id = 0x3e, .name = "WM5102-6271-EV1-CS127", - .i2c_devs = wm5102_devs, .num_i2c_devs = ARRAY_SIZE(wm5102_devs) }, + { .id = 0x3e, .name = "WM5102-6271-EV1-CS127 Amrut", + .spi_devs = wm5102_spi_devs, + .num_spi_devs = ARRAY_SIZE(wm5102_spi_devs) }, }; static __devinit int wlf_gf_module_probe(struct i2c_client *i2c, diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c index 09cd81207a3..a095f7f6009 100644 --- a/arch/arm/mach-s3c64xx/mach-crag6410.c +++ b/arch/arm/mach-s3c64xx/mach-crag6410.c @@ -287,6 +287,16 @@ static struct platform_device littlemill_device = { .id = -1, }; +static struct platform_device bells_wm5102_device = { + .name = "bells", + .id = 0, +}; + +static struct platform_device bells_wm5110_device = { + .name = "bells", + .id = 1, +}; + static struct regulator_consumer_supply wallvdd_consumers[] = { REGULATOR_SUPPLY("SPKVDD", "1-001a"), REGULATOR_SUPPLY("SPKVDD1", "1-001a"), @@ -359,6 +369,8 @@ static struct platform_device *crag6410_devices[] __initdata = { &tobermory_device, &littlemill_device, &lowland_device, + &bells_wm5102_device, + &bells_wm5110_device, &wallvdd_device, }; diff --git a/arch/arm/mach-shmobile/board-armadillo800eva.c b/arch/arm/mach-shmobile/board-armadillo800eva.c index 45b33e02dff..9615a78d30b 100644 --- a/arch/arm/mach-shmobile/board-armadillo800eva.c +++ b/arch/arm/mach-shmobile/board-armadillo800eva.c @@ -37,6 +37,7 @@ #include <linux/mmc/host.h> #include <linux/mmc/sh_mmcif.h> #include <linux/mmc/sh_mobile_sdhi.h> +#include <linux/i2c-gpio.h> #include <mach/common.h> #include <mach/irqs.h> #include <mach/r8a7740.h> @@ -877,6 +878,21 @@ static struct platform_device fsi_hdmi_device = { }, }; +/* RTC: RTC connects i2c-gpio. */ +static struct i2c_gpio_platform_data i2c_gpio_data = { + .sda_pin = GPIO_PORT208, + .scl_pin = GPIO_PORT91, + .udelay = 5, /* 100 kHz */ +}; + +static struct platform_device i2c_gpio_device = { + .name = "i2c-gpio", + .id = 2, + .dev = { + .platform_data = &i2c_gpio_data, + }, +}; + /* I2C */ static struct i2c_board_info i2c0_devices[] = { { @@ -888,6 +904,13 @@ static struct i2c_board_info i2c0_devices[] = { }, }; +static struct i2c_board_info i2c2_devices[] = { + { + I2C_BOARD_INFO("s35390a", 0x30), + .type = "s35390a", + }, +}; + /* * board devices */ @@ -904,6 +927,7 @@ static struct platform_device *eva_devices[] __initdata = { &fsi_device, &fsi_wm8978_device, &fsi_hdmi_device, + &i2c_gpio_device, }; static void __init eva_clock_init(void) @@ -1174,6 +1198,7 @@ static void __init eva_init(void) #endif i2c_register_board_info(0, i2c0_devices, ARRAY_SIZE(i2c0_devices)); + i2c_register_board_info(2, i2c2_devices, ARRAY_SIZE(i2c2_devices)); r8a7740_add_standard_devices(); diff --git a/arch/arm/mach-shmobile/board-marzen.c b/arch/arm/mach-shmobile/board-marzen.c index fcf5a47f477..4834bdd849c 100644 --- a/arch/arm/mach-shmobile/board-marzen.c +++ b/arch/arm/mach-shmobile/board-marzen.c @@ -30,6 +30,8 @@ #include <linux/regulator/fixed.h> #include <linux/regulator/machine.h> #include <linux/smsc911x.h> +#include <linux/mmc/sh_mobile_sdhi.h> +#include <linux/mfd/tmio.h> #include <mach/hardware.h> #include <mach/r8a7779.h> #include <mach/common.h> @@ -39,6 +41,12 @@ #include <asm/hardware/gic.h> #include <asm/traps.h> +/* Fixed 3.3V regulator to be used by SDHI0 */ +static struct regulator_consumer_supply fixed3v3_power_consumers[] = { + REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"), + REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"), +}; + /* Dummy supplies, where voltage doesn't matter */ static struct regulator_consumer_supply dummy_supplies[] = { REGULATOR_SUPPLY("vddvario", "smsc911x"), @@ -75,13 +83,61 @@ static struct platform_device eth_device = { .num_resources = ARRAY_SIZE(smsc911x_resources), }; +static struct resource sdhi0_resources[] = { + [0] = { + .name = "sdhi0", + .start = 0xffe4c000, + .end = 0xffe4c0ff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = gic_spi(104), + .flags = IORESOURCE_IRQ, + }, +}; + +static struct sh_mobile_sdhi_info sdhi0_platform_data = { + .tmio_flags = TMIO_MMC_WRPROTECT_DISABLE | TMIO_MMC_HAS_IDLE_WAIT, + .tmio_caps = MMC_CAP_SD_HIGHSPEED, +}; + +static struct platform_device sdhi0_device = { + .name = "sh_mobile_sdhi", + .num_resources = ARRAY_SIZE(sdhi0_resources), + .resource = sdhi0_resources, + .id = 0, + .dev = { + .platform_data = &sdhi0_platform_data, + } +}; + +/* Thermal */ +static struct resource thermal_resources[] = { + [0] = { + .start = 0xFFC48000, + .end = 0xFFC48038 - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device thermal_device = { + .name = "rcar_thermal", + .resource = thermal_resources, + .num_resources = ARRAY_SIZE(thermal_resources), +}; + static struct platform_device *marzen_devices[] __initdata = { ð_device, + &sdhi0_device, + &thermal_device, }; static void __init marzen_init(void) { - regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies)); + regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers, + ARRAY_SIZE(fixed3v3_power_consumers), 3300000); + regulator_register_fixed(1, dummy_supplies, + ARRAY_SIZE(dummy_supplies)); r8a7779_pinmux_init(); @@ -97,6 +153,16 @@ static void __init marzen_init(void) gpio_request(GPIO_FN_EX_CS0, NULL); /* nCS */ gpio_request(GPIO_FN_IRQ1_B, NULL); /* IRQ + PME */ + /* SD0 (CN20) */ + gpio_request(GPIO_FN_SD0_CLK, NULL); + gpio_request(GPIO_FN_SD0_CMD, NULL); + gpio_request(GPIO_FN_SD0_DAT0, NULL); + gpio_request(GPIO_FN_SD0_DAT1, NULL); + gpio_request(GPIO_FN_SD0_DAT2, NULL); + gpio_request(GPIO_FN_SD0_DAT3, NULL); + gpio_request(GPIO_FN_SD0_CD, NULL); + gpio_request(GPIO_FN_SD0_WP, NULL); + r8a7779_add_standard_devices(); platform_add_devices(marzen_devices, ARRAY_SIZE(marzen_devices)); } |