diff options
| -rw-r--r-- | arch/powerpc/boot/dts/mpc885ads.dts | 185 | ||||
| -rw-r--r-- | arch/powerpc/configs/mpc885_ads_defconfig | 827 | ||||
| -rw-r--r-- | arch/powerpc/platforms/8xx/Kconfig | 300 | ||||
| -rw-r--r-- | arch/powerpc/platforms/8xx/Makefile | 5 | ||||
| -rw-r--r-- | arch/powerpc/platforms/8xx/m8xx_setup.c | 303 | ||||
| -rw-r--r-- | arch/powerpc/platforms/8xx/mpc885ads.h | 95 | ||||
| -rw-r--r-- | arch/powerpc/platforms/8xx/mpc885ads_setup.c | 387 | ||||
| -rw-r--r-- | arch/powerpc/platforms/Makefile | 1 |
8 files changed, 1846 insertions, 257 deletions
diff --git a/arch/powerpc/boot/dts/mpc885ads.dts b/arch/powerpc/boot/dts/mpc885ads.dts new file mode 100644 index 00000000000..cf1a19f962c --- /dev/null +++ b/arch/powerpc/boot/dts/mpc885ads.dts @@ -0,0 +1,185 @@ +/* + * MPC885 ADS Device Tree Source + * + * Copyright 2006 MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + + +/ { + model = "MPC885ADS"; + compatible = "mpc8xx"; + #address-cells = <1>; + #size-cells = <1>; + linux,phandle = <100>; + + cpus { + #cpus = <1>; + #address-cells = <1>; + #size-cells = <0>; + linux,phandle = <200>; + + PowerPC,885@0 { + device_type = "cpu"; + reg = <0>; + d-cache-line-size = <20>; // 32 bytes + i-cache-line-size = <20>; // 32 bytes + d-cache-size = <2000>; // L1, 8K + i-cache-size = <2000>; // L1, 8K + timebase-frequency = <0>; + bus-frequency = <0>; + clock-frequency = <0>; + 32-bit; + interrupts = <f 2>; // decrementer interrupt + interrupt-parent = <ff000000>; + linux,phandle = <201>; + linux,boot-cpu; + }; + }; + + memory { + device_type = "memory"; + linux,phandle = <300>; + reg = <00000000 800000>; + }; + + soc885@ff000000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "soc"; + ranges = <0 ff000000 00100000>; + reg = <ff000000 00000200>; + bus-frequency = <0>; + mdio@e80 { + device_type = "mdio"; + compatible = "fs_enet"; + reg = <e80 8>; + linux,phandle = <e80>; + #address-cells = <1>; + #size-cells = <0>; + ethernet-phy@0 { + linux,phandle = <e8000>; + reg = <0>; + device_type = "ethernet-phy"; + }; + ethernet-phy@1 { + linux,phandle = <e8001>; + reg = <1>; + device_type = "ethernet-phy"; + }; + ethernet-phy@2 { + linux,phandle = <e8002>; + reg = <2>; + device_type = "ethernet-phy"; + }; + }; + + fec@e00 { + device_type = "network"; + compatible = "fs_enet"; + model = "FEC"; + device-id = <1>; + reg = <e00 188>; + mac-address = [ 00 00 0C 00 01 FD ]; + interrupts = <3 1>; + interrupt-parent = <ff000000>; + phy-handle = <e8000>; + }; + + fec@1e00 { + device_type = "network"; + compatible = "fs_enet"; + model = "FEC"; + device-id = <2>; + reg = <1e00 188>; + mac-address = [ 00 00 0C 00 02 FD ]; + interrupts = <7 1>; + interrupt-parent = <ff000000>; + phy-handle = <e8001>; + }; + + pic@ff000000 { + linux,phandle = <ff000000>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0 24>; + built-in; + device_type = "mpc8xx-pic"; + compatible = "CPM"; + }; + + cpm@ff000000 { + linux,phandle = <ff000000>; + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "cpm"; + model = "CPM"; + ranges = <0 0 4000>; + reg = <860 f0>; + command-proc = <9c0>; + brg-frequency = <0>; + interrupts = <0 2>; // cpm error interrupt + interrupt-parent = <930>; + + pic@930 { + linux,phandle = <930>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + interrupts = <5 2 0 2>; + interrupt-parent = <ff000000>; + reg = <930 20>; + built-in; + device_type = "cpm-pic"; + compatible = "CPM"; + }; + + smc@a80 { + device_type = "serial"; + compatible = "cpm_uart"; + model = "SMC"; + device-id = <1>; + reg = <a80 10 3e80 40>; + clock-setup = <00ffffff 0>; + rx-clock = <1>; + tx-clock = <1>; + current-speed = <0>; + interrupts = <4 3>; + interrupt-parent = <930>; + }; + + smc@a90 { + device_type = "serial"; + compatible = "cpm_uart"; + model = "SMC"; + device-id = <2>; + reg = <a90 20 3f80 40>; + clock-setup = <ff00ffff 90000>; + rx-clock = <2>; + tx-clock = <2>; + current-speed = <0>; + interrupts = <3 3>; + interrupt-parent = <930>; + }; + + scc@a40 { + device_type = "network"; + compatible = "fs_enet"; + model = "SCC"; + device-id = <3>; + reg = <a40 18 3e00 80>; + mac-address = [ 00 00 0C 00 03 FD ]; + interrupts = <1c 3>; + interrupt-parent = <930>; + phy-handle = <e8002>; + }; + }; + }; +}; diff --git a/arch/powerpc/configs/mpc885_ads_defconfig b/arch/powerpc/configs/mpc885_ads_defconfig new file mode 100644 index 00000000000..e2c17d8da4f --- /dev/null +++ b/arch/powerpc/configs/mpc885_ads_defconfig @@ -0,0 +1,827 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.19-rc4 +# Fri Nov 10 21:30:40 2006 +# +# CONFIG_PPC64 is not set +CONFIG_PPC32=y +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_IRQ_PER_CPU=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +# CONFIG_PPC_UDBG_16550 is not set +# CONFIG_GENERIC_TBSYNC is not set +CONFIG_AUDIT_ARCH=y +# CONFIG_DEFAULT_UIMAGE is not set + +# +# Processor support +# +# CONFIG_CLASSIC32 is not set +# CONFIG_PPC_52xx is not set +# CONFIG_PPC_82xx is not set +# CONFIG_PPC_83xx is not set +# CONFIG_PPC_85xx is not set +# CONFIG_PPC_86xx is not set +CONFIG_PPC_8xx=y +# CONFIG_40x is not set +# CONFIG_44x is not set +# CONFIG_E200 is not set +CONFIG_8xx=y +CONFIG_NOT_COHERENT_CACHE=y +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +# CONFIG_IPC_NS is not set +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_UTS_NS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +# CONFIG_SYSCTL_SYSCALL is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_EXTRA_PASS is not set +# CONFIG_HOTPLUG is not set +CONFIG_PRINTK=y +# CONFIG_BUG is not set +CONFIG_ELF_CORE=y +# CONFIG_BASE_FULL is not set +CONFIG_FUTEX=y +# CONFIG_EPOLL is not set +CONFIG_SHMEM=y +CONFIG_SLAB=y +# CONFIG_VM_EVENT_COUNTERS is not set +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=1 +# CONFIG_SLOB is not set + +# +# Loadable module support +# +# CONFIG_MODULES is not set + +# +# Block layer +# +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +# CONFIG_WANT_EARLY_SERIAL is not set +CONFIG_EMBEDDEDBOOT=y +# CONFIG_MPIC is not set + +# +# Platform support +# +CONFIG_CPM1=y +# CONFIG_MPC8XXFADS is not set +# CONFIG_MPC86XADS is not set +CONFIG_MPC885ADS=y + +# +# MPC8xx CPM Options +# + +# +# Generic MPC8xx Options +# +CONFIG_8xx_COPYBACK=y +# CONFIG_8xx_CPU6 is not set +CONFIG_NO_UCODE_PATCH=y +# CONFIG_USB_SOF_UCODE_PATCH is not set +# CONFIG_I2C_SPI_UCODE_PATCH is not set +# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set + +# +# Kernel options +# +# CONFIG_HIGHMEM is not set +# CONFIG_HZ_100 is not set +# CONFIG_HZ_250 is not set +CONFIG_HZ_1000=y +CONFIG_HZ=1000 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_MISC is not set +CONFIG_MATH_EMULATION=y +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_RESOURCES_64BIT is not set +# CONFIG_PROC_DEVICETREE is not set +# CONFIG_CMDLINE_BOOL is not set +# CONFIG_PM is not set +# CONFIG_SECCOMP is not set +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +# CONFIG_MPIC_WEIRD is not set +# CONFIG_PPC_I8259 is not set +CONFIG_FSL_SOC=y +# CONFIG_PCI is not set +# CONFIG_PCI_DOMAINS is not set +# CONFIG_PCI_QSPAN is not set + +# +# PCCARD (PCMCIA/CardBus) support +# + +# +# PCI Hotplug Support +# + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_HIGHMEM_START=0xfe000000 +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_TASK_SIZE=0x80000000 +CONFIG_CONSISTENT_START=0xff100000 +CONFIG_CONSISTENT_SIZE=0x00200000 +CONFIG_BOOT_LOAD=0x00400000 + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +# CONFIG_NETDEBUG is not set +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +# CONFIG_IP_PNP_BOOTP is not set +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_SYS_HYPERVISOR is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +# CONFIG_MTD is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# + +# +# Block devices +# +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_RAM is not set +# CONFIG_BLK_DEV_INITRD is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# Misc devices +# +# CONFIG_TIFM_CORE is not set + +# +# ATA/ATAPI/MFM/RLL support +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set +# CONFIG_SCSI_NETLINK is not set + +# +# Serial ATA (prod) and Parallel ATA (experimental) drivers +# +# CONFIG_ATA is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# I2O device support +# + +# +# Macintosh device drivers +# +# CONFIG_WINDFARM is not set + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# PHY device support +# +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +CONFIG_DAVICOM_PHY=y +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +CONFIG_FIXED_PHY=y +CONFIG_FIXED_MII_10_FDX=y +# CONFIG_FIXED_MII_100_FDX is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_FEC_8XX is not set +CONFIG_FS_ENET=y +CONFIG_FS_ENET_HAS_SCC=y +CONFIG_FS_ENET_HAS_FEC=y + +# +# Ethernet (1000 Mbit) +# + +# +# Ethernet (10000 Mbit) +# + +# +# Token Ring devices +# + +# +# Wireless LAN (non-hamradio) +# +# CONFIG_NET_RADIO is not set + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Telephony Support +# +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +CONFIG_INPUT_KEYBOARD=y +CONFIG_KEYBOARD_ATKBD=y +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_LKKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_STOWAWAY is not set +CONFIG_INPUT_MOUSE=y +CONFIG_MOUSE_PS2=y +# CONFIG_MOUSE_SERIAL is not set +# CONFIG_MOUSE_VSXXXAA is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +CONFIG_SERIO=y +CONFIG_SERIO_I8042=y +CONFIG_SERIO_SERPORT=y +CONFIG_SERIO_LIBPS2=y +# CONFIG_SERIO_RAW is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_VT is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_SERIAL_CPM=y +CONFIG_SERIAL_CPM_CONSOLE=y +# CONFIG_SERIAL_CPM_SCC1 is not set +# CONFIG_SERIAL_CPM_SCC2 is not set +# CONFIG_SERIAL_CPM_SCC3 is not set +# CONFIG_SERIAL_CPM_SCC4 is not set +CONFIG_SERIAL_CPM_SMC1=y +CONFIG_SERIAL_CPM_SMC2=y +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +# CONFIG_WATCHDOG is not set +CONFIG_HW_RANDOM=y +# CONFIG_NVRAM is not set +CONFIG_GEN_RTC=y +# CONFIG_GEN_RTC_X is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set + +# +# Ftape, the floppy tape device driver +# +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set + +# +# I2C support +# +# CONFIG_I2C is not set + +# +# SPI support +# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Hardware Monitoring support +# +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_ABITUGURU is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_VT1211 is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set + +# +# Graphics support +# +CONFIG_FIRMWARE_EDID=y +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# USB support +# +# CONFIG_USB_ARCH_HAS_HCD is not set +# CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# USB Gadget Support +# +# CONFIG_USB_GADGET is not set + +# +# MMC/SD Card support +# +# CONFIG_MMC is not set + +# +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# +# InfiniBand support +# + +# +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock +# +# CONFIG_RTC_CLASS is not set + +# +# DMA Engine support +# +# CONFIG_DMA_ENGINE is not set + +# +# DMA Clients +# + +# +# DMA Devices +# + +# +# File systems +# +CONFIG_EXT2_FS=y +CONFIG_EXT2_FS_XATTR=y +# CONFIG_EXT2_FS_POSIX_ACL is not set +# CONFIG_EXT2_FS_SECURITY is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +CONFIG_EXT3_FS_XATTR=y +# CONFIG_EXT3_FS_POSIX_ACL is not set +# CONFIG_EXT3_FS_SECURITY is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=y +# CONFIG_JBD_DEBUG is not set +CONFIG_FS_MBCACHE=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +# CONFIG_PROC_KCORE is not set +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set + +# +# Native Language Support +# +# CONFIG_NLS is not set + +# +# Library routines +# +CONFIG_CRC_CCITT=y +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_PLIST=y + +# +# Instrumentation Support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_MUST_CHECK=y +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_KERNEL is not set +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set +# CONFIG_UNWIND_INFO is not set +# CONFIG_HEADERS_CHECK is not set +# CONFIG_BOOTX_TEXT is not set +# CONFIG_PPC_EARLY_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +# CONFIG_CRYPTO is not set diff --git a/arch/powerpc/platforms/8xx/Kconfig b/arch/powerpc/platforms/8xx/Kconfig index c8c0ba3cf8e..beea6834bb7 100644 --- a/arch/powerpc/platforms/8xx/Kconfig +++ b/arch/powerpc/platforms/8xx/Kconfig @@ -1,105 +1,16 @@ +menu "Platform support" + depends on PPC_8xx + config FADS bool +config CPM1 + bool + choice prompt "8xx Machine Type" depends on 8xx - default RPXLITE - -config RPXLITE - bool "RPX-Lite" - ---help--- - Single-board computers based around the PowerPC MPC8xx chips and - intended for embedded applications. The following types are - supported: - - RPX-Lite: - Embedded Planet RPX Lite. PC104 form-factor SBC based on the MPC823. - - RPX-Classic: - Embedded Planet RPX Classic Low-fat. Credit-card-size SBC based on - the MPC 860 - - BSE-IP: - Bright Star Engineering ip-Engine. - - TQM823L: - TQM850L: - TQM855L: - TQM860L: - MPC8xx based family of mini modules, half credit card size, - up to 64 MB of RAM, 8 MB Flash, (Fast) Ethernet, 2 x serial ports, - 2 x CAN bus interface, ... - Manufacturer: TQ Components, www.tq-group.de - Date of Release: October (?) 1999 - End of Life: not yet :-) - URL: - - module: <http://www.denx.de/PDF/TQM8xxLHWM201.pdf> - - starter kit: <http://www.denx.de/PDF/STK8xxLHWM201.pdf> - - images: <http://www.denx.de/embedded-ppc-en.html> - - FPS850L: - FingerPrint Sensor System (based on TQM850L) - Manufacturer: IKENDI AG, <http://www.ikendi.com/> - Date of Release: November 1999 - End of life: end 2000 ? - URL: see TQM850L - - IVMS8: - MPC860 based board used in the "Integrated Voice Mail System", - Small Version (8 voice channels) - Manufacturer: Speech Design, <http://www.speech-design.de/> - Date of Release: December 2000 (?) - End of life: - - URL: <http://www.speech-design.de/> - - IVML24: - MPC860 based board used in the "Integrated Voice Mail System", - Large Version (24 voice channels) - Manufacturer: Speech Design, <http://www.speech-design.de/> - Date of Release: March 2001 (?) - End of life: - - URL: <http://www.speech-design.de/> - - HERMES: - Hermes-Pro ISDN/LAN router with integrated 8 x hub - Manufacturer: Multidata Gesellschaft fur Datentechnik und Informatik - <http://www.multidata.de/> - Date of Release: 2000 (?) - End of life: - - URL: <http://www.multidata.de/english/products/hpro.htm> - - IP860: - VMEBus IP (Industry Pack) carrier board with MPC860 - Manufacturer: MicroSys GmbH, <http://www.microsys.de/> - Date of Release: ? - End of life: - - URL: <http://www.microsys.de/html/ip860.html> - - PCU_E: - PCU = Peripheral Controller Unit, Extended - Manufacturer: Siemens AG, ICN (Information and Communication Networks) - <http://www.siemens.de/page/1,3771,224315-1-999_2_226207-0,00.html> - Date of Release: April 2001 - End of life: August 2001 - URL: n. a. - -config RPXCLASSIC - bool "RPX-Classic" - help - The RPX-Classic is a single-board computer based on the Motorola - MPC860. It features 16MB of DRAM and a variable amount of flash, - I2C EEPROM, thermal monitoring, a PCMCIA slot, a DIP switch and two - LEDs. Variants with Ethernet ports exist. Say Y here to support it - directly. - -config BSEIP - bool "BSE-IP" - help - Say Y here to support the Bright Star Engineering ipEngine SBC. - This is a credit-card-sized device featuring a MPC823 processor, - 26MB DRAM, 4MB flash, Ethernet, a 16K-gate FPGA, USB, an LCD/video - controller, and two RS232 ports. + default MPC885ADS config MPC8XXFADS bool "FADS" @@ -107,110 +18,58 @@ config MPC8XXFADS config MPC86XADS bool "MPC86XADS" + select CPM1 help MPC86x Application Development System by Freescale Semiconductor. The MPC86xADS is meant to serve as a platform for s/w and h/w development around the MPC86X processor families. - select FADS config MPC885ADS bool "MPC885ADS" + select CPM1 help Freescale Semiconductor MPC885 Application Development System (ADS). Also known as DUET. The MPC885ADS is meant to serve as a platform for s/w and h/w development around the MPC885 processor family. -config TQM823L - bool "TQM823L" - help - Say Y here to support the TQM823L, one of an MPC8xx-based family of - mini SBCs (half credit-card size) from TQ Components first released - in late 1999. Technical references are at - <http://www.denx.de/PDF/TQM8xxLHWM201.pdf>, and - <http://www.denx.de/PDF/STK8xxLHWM201.pdf>, and an image at - <http://www.denx.de/embedded-ppc-en.html>. - -config TQM850L - bool "TQM850L" - help - Say Y here to support the TQM850L, one of an MPC8xx-based family of - mini SBCs (half credit-card size) from TQ Components first released - in late 1999. Technical references are at - <http://www.denx.de/PDF/TQM8xxLHWM201.pdf>, and - <http://www.denx.de/PDF/STK8xxLHWM201.pdf>, and an image at - <http://www.denx.de/embedded-ppc-en.html>. - -config TQM855L - bool "TQM855L" - help - Say Y here to support the TQM855L, one of an MPC8xx-based family of - mini SBCs (half credit-card size) from TQ Components first released - in late 1999. Technical references are at - <http://www.denx.de/PDF/TQM8xxLHWM201.pdf>, and - <http://www.denx.de/PDF/STK8xxLHWM201.pdf>, and an image at - <http://www.denx.de/embedded-ppc-en.html>. - -config TQM860L - bool "TQM860L" - help - Say Y here to support the TQM860L, one of an MPC8xx-based family of - mini SBCs (half credit-card size) from TQ Components first released - in late 1999. Technical references are at - <http://www.denx.de/PDF/TQM8xxLHWM201.pdf>, and - <http://www.denx.de/PDF/STK8xxLHWM201.pdf>, and an image at - <http://www.denx.de/embedded-ppc-en.html>. - -config FPS850L - bool "FPS850L" - -config IVMS8 - bool "IVMS8" - help - Say Y here to support the Integrated Voice-Mail Small 8-channel SBC - from Speech Design, released March 2001. The manufacturer's website - is at <http://www.speech-design.de/>. - -config IVML24 - bool "IVML24" - help - Say Y here to support the Integrated Voice-Mail Large 24-channel SBC - from Speech Design, released March 2001. The manufacturer's website - is at <http://www.speech-design.de/>. - -config HERMES_PRO - bool "HERMES" - -config IP860 - bool "IP860" - -config LWMON - bool "LWMON" - -config PCU_E - bool "PCU_E" - -config CCM - bool "CCM" - -config LANTEC - bool "LANTEC" +endchoice -config MBX - bool "MBX" - help - MBX is a line of Motorola single-board computer based around the - MPC821 and MPC860 processors, and intended for embedded-controller - applications. Say Y here to support these boards directly. +menu "Freescale Ethernet driver platform-specific options" + depends on (FS_ENET && MPC885ADS) + + config MPC8xx_SECOND_ETH + bool "Second Ethernet channel" + depends on MPC885ADS + default y + help + This enables support for second Ethernet on MPC885ADS and MPC86xADS boards. + The latter will use SCC1, for 885ADS you can select it below. + + choice + prompt "Second Ethernet channel" + depends on MPC8xx_SECOND_ETH + default MPC8xx_SECOND_ETH_FEC2 + + config MPC8xx_SECOND_ETH_FEC2 + bool "FEC2" + depends on MPC885ADS + help + Enable FEC2 to serve as 2-nd Ethernet channel. Note that SMC2 + (often 2-nd UART) will not work if this is enabled. + + config MPC8xx_SECOND_ETH_SCC3 + bool "SCC3" + depends on MPC885ADS + help + Enable SCC3 to serve as 2-nd Ethernet channel. Note that SMC1 + (often 1-nd UART) will not work if this is enabled. + + endchoice -config WINCEPT - bool "WinCept" - help - The Wincept 100/110 is a Motorola single-board computer based on the - MPC821 PowerPC, introduced in 1998 and designed to be used in - thin-client machines. Say Y to support it directly. +endmenu -endchoice +endmenu # # MPC8xx Communication options @@ -219,79 +78,6 @@ endchoice menu "MPC8xx CPM Options" depends on 8xx -config SCC_ENET - bool "CPM SCC Ethernet" - depends on NET_ETHERNET - help - Enable Ethernet support via the Motorola MPC8xx serial - communications controller. - -choice - prompt "SCC used for Ethernet" - depends on SCC_ENET - default SCC1_ENET - -config SCC1_ENET - bool "SCC1" - help - Use MPC8xx serial communications controller 1 to drive Ethernet - (default). - -config SCC2_ENET - bool "SCC2" - help - Use MPC8xx serial communications controller 2 to drive Ethernet. - -config SCC3_ENET - bool "SCC3" - help - Use MPC8xx serial communications controller 3 to drive Ethernet. - -endchoice - -config FEC_ENET - bool "860T FEC Ethernet" - depends on NET_ETHERNET - help - Enable Ethernet support via the Fast Ethernet Controller (FCC) on - the Motorola MPC8260. - -config USE_MDIO - bool "Use MDIO for PHY configuration" - depends on FEC_ENET - help - On some boards the hardware configuration of the ethernet PHY can be - used without any software interaction over the MDIO interface, so - all MII code can be omitted. Say N here if unsure or if you don't - need link status reports. - -config FEC_AM79C874 - bool "Support AMD79C874 PHY" - depends on USE_MDIO - -config FEC_LXT970 - bool "Support LXT970 PHY" - depends on USE_MDIO - -config FEC_LXT971 - bool "Support LXT971 PHY" - depends on USE_MDIO - -config FEC_QS6612 - bool "Support QS6612 PHY" - depends on USE_MDIO - -config ENET_BIG_BUFFERS - bool "Use Big CPM Ethernet Buffers" - depends on SCC_ENET || FEC_ENET - help - Allocate large buffers for MPC8xx Ethernet. Increases throughput - and decreases the likelihood of dropped packets, but costs memory. - -config HTDMSOUND - bool "Embedded Planet HIOX Audio" - depends on SOUND=y - # This doesn't really belong here, but it is convenient to ask # 8xx specific questions. comment "Generic MPC8xx Options" diff --git a/arch/powerpc/platforms/8xx/Makefile b/arch/powerpc/platforms/8xx/Makefile new file mode 100644 index 00000000000..1b59ffa9252 --- /dev/null +++ b/arch/powerpc/platforms/8xx/Makefile @@ -0,0 +1,5 @@ +# +# Makefile for the PowerPC 8xx linux kernel. +# +obj-$(CONFIG_PPC_8xx) += m8xx_setup.o +obj-$(CONFIG_MPC885ADS) += mpc885ads_setup.o diff --git a/arch/powerpc/platforms/8xx/m8xx_setup.c b/arch/powerpc/platforms/8xx/m8xx_setup.c new file mode 100644 index 00000000000..9ed7125f015 --- /dev/null +++ b/arch/powerpc/platforms/8xx/m8xx_setup.c @@ -0,0 +1,303 @@ +/* + * Copyright (C) 1995 Linus Torvalds + * Adapted from 'alpha' version by Gary Thomas + * Modified by Cort Dougan (cort@cs.nmt.edu) + * Modified for MBX using prep/chrp/pmac functions by Dan (dmalek@jlc.net) + * Further modified for generic 8xx by Dan. + */ + +/* + * bootup setup stuff.. + */ + +#include <linux/errno.h> +#include <linux/sched.h> +#include <linux/kernel.h> +#include <linux/mm.h> +#include <linux/stddef.h> +#include <linux/unistd.h> +#include <linux/ptrace.h> +#include <linux/slab.h> +#include <linux/user.h> +#include <linux/a.out.h> +#include <linux/tty.h> +#include <linux/major.h> +#include <linux/interrupt.h> +#include <linux/reboot.h> +#include <linux/init.h> +#include <linux/initrd.h> +#include <linux/ioport.h> +#include <linux/bootmem.h> +#include <linux/seq_file.h> +#include <linux/root_dev.h> +#include <linux/time.h> +#include <linux/rtc.h> + +#include <asm/mmu.h> +#include <asm/reg.h> +#include <asm/residual.h> +#include <asm/io.h> +#include <asm/pgtable.h> +#include <asm/mpc8xx.h> +#include <asm/8xx_immap.h> +#include <asm/machdep.h> +#include <asm/bootinfo.h> +#include <asm/time.h> +#include <asm/prom.h> +#include <asm/fs_pd.h> +#include <mm/mmu_decl.h> + +#include "sysdev/mpc8xx_pic.h" + +void m8xx_calibrate_decr(void); +extern void m8xx_wdt_handler_install(bd_t *bp); +extern int cpm_pic_init(void); +extern int cpm_get_irq(void); + +/* A place holder for time base interrupts, if they are ever enabled. */ +irqreturn_t timebase_interrupt(int irq, void * dev) +{ + printk ("timebase_interrupt()\n"); + + return IRQ_HANDLED; +} + +static struct irqaction tbint_irqaction = { + .handler = timebase_interrupt, + .mask = CPU_MASK_NONE, + .name = "tbint", +}; + +/* per-board overridable init_internal_rtc() function. */ +void __init __attribute__ ((weak)) +init_internal_rtc(void) +{ + sit8xx_t *sys_tmr = (sit8xx_t *) immr_map(im_sit); + + /* Disable the RTC one second and alarm interrupts. */ + clrbits16(&sys_tmr->sit_rtcsc, (RTCSC_SIE | RTCSC_ALE)); + + /* Enable the RTC */ + setbits16(&sys_tmr->sit_rtcsc, (RTCSC_RTF | RTCSC_RTE)); + immr_unmap(sys_tmr); +} + +static int __init get_freq(char *name, unsigned long *val) +{ + struct device_node *cpu; + unsigned int *fp; + int found = 0; + + /* The cpu node should have timebase and clock frequency properties */ + cpu = of_find_node_by_type(NULL, "cpu"); + + if (cpu) { + fp = (unsigned int *)get_property(cpu, name, NULL); + if (fp) { + found = 1; + *val = *fp++; + } + + of_node_put(cpu); + } + + return found; +} + +/* The decrementer counts at the system (internal) clock frequency divided by + * sixteen, or external oscillator divided by four. We force the processor + * to use system clock divided by sixteen. + */ +void __init mpc8xx_calibrate_decr(void) +{ + struct device_node *cpu; + cark8xx_t *clk_r1; + car8xx_t *clk_r2; + sitk8xx_t *sys_tmr1; + sit8xx_t *sys_tmr2; + int irq, virq; + + clk_r1 = (cark8xx_t *) immr_map(im_clkrstk); + + /* Unlock the SCCR. */ + out_be32(&clk_r1->cark_sccrk, ~KAPWR_KEY); + out_be32(&clk_r1->cark_sccrk, KAPWR_KEY); + immr_unmap(clk_r1); + + /* Force all 8xx processors to use divide by 16 processor clock. */ + clk_r2 = (car8xx_t *) immr_map(im_clkrst); + setbits32(&clk_r2->car_sccr, 0x02000000); + immr_unmap(clk_r2); + + /* Processor frequency is MHz. + */ + ppc_tb_freq = 50000000; + if (!get_freq("bus-frequency", &ppc_tb_freq)) { + printk(KERN_ERR "WARNING: Estimating decrementer frequency " + "(not found)\n"); + } + ppc_tb_freq /= 16; + ppc_proc_freq = 50000000; + if (!get_freq("clock-frequency", &ppc_proc_freq)) + printk(KERN_ERR "WARNING: Estimating processor frequency" + "(not found)\n"); + + printk("Decrementer Frequency = 0x%lx\n", ppc_tb_freq); + + /* Perform some more timer/timebase initialization. This used + * to be done elsewhere, but other changes caused it to get + * called more than once....that is a bad thing. + * + * First, unlock all of the registers we are going to modify. + * To protect them from corruption during power down, registers + * that are maintained by keep alive power are "locked". To + * modify these registers we have to write the key value to + * the key location associated with the register. + * Some boards power up with these unlocked, while others + * are locked. Writing anything (including the unlock code?) + * to the unlocked registers will lock them again. So, here + * we guarantee the registers are locked, then we unlock them + * for our use. + */ + sys_tmr1 = (sitk8xx_t *) immr_map(im_sitk); + out_be32(&sys_tmr1->sitk_tbscrk, ~KAPWR_KEY); + out_be32(&sys_tmr1->sitk_rtcsck, ~KAPWR_KEY); + out_be32(&sys_tmr1->sitk_tbk, ~KAPWR_KEY); + out_be32(&sys_tmr1->sitk_tbscrk, KAPWR_KEY); + out_be32(&sys_tmr1->sitk_rtcsck, KAPWR_KEY); + out_be32(&sys_tmr1->sitk_tbk, KAPWR_KEY); + immr_unmap(sys_tmr1); + + init_internal_rtc(); + + /* Enabling the decrementer also enables the timebase interrupts + * (or from the other point of view, to get decrementer interrupts + * we have to enable the timebase). The decrementer interrupt + * is wired into the vector table, nothing to do here for that. + */ + cpu = of_find_node_by_type(NULL, "cpu"); + virq= irq_of_parse_and_map(cpu, 0); + irq = irq_map[virq].hwirq; + + sys_tmr2 = (sit8xx_t *) immr_map(im_sit); + out_be16(&sys_tmr2->sit_tbscr, ((1 << (7 - (irq/2))) << 8) | + (TBSCR_TBF | TBSCR_TBE)); + immr_unmap(sys_tmr2); + + if (setup_irq(virq, &tbint_irqaction)) + panic("Could not allocate timer IRQ!"); + +#ifdef CONFIG_8xx_WDT + /* Install watchdog timer handler early because it might be + * already enabled by the bootloader + */ + m8xx_wdt_handler_install(binfo); +#endif +} + +/* The RTC on the MPC8xx is an internal register. + * We want to protect this during power down, so we need to unlock, + * modify, and re-lock. + */ + +int mpc8xx_set_rtc_time(struct rtc_time *tm) +{ + sitk8xx_t *sys_tmr1; + sit8xx_t *sys_tmr2; + int time; + + sys_tmr1 = (sitk8xx_t *) immr_map(im_sitk); + sys_tmr2 = (sit8xx_t *) immr_map(im_sit); + time = mktime(tm->tm_year+1900, tm->tm_mon+1, tm->tm_mday, + tm->tm_hour, tm->tm_min, tm->tm_sec); + + out_be32(&sys_tmr1->sitk_rtck, KAPWR_KEY); + out_be32(&sys_tmr2->sit_rtc, time); + out_be32(&sys_tmr1->sitk_rtck, ~KAPWR_KEY); + + immr_unmap(sys_tmr2); + immr_unmap(sys_tmr1); + return 0; +} + +void mpc8xx_get_rtc_time(struct rtc_time *tm) +{ + unsigned long data; + sit8xx_t *sys_tmr = (sit8xx_t *) immr_map(im_sit); + + /* Get time from the RTC. */ + data = in_be32(&sys_tmr->sit_rtc); + to_tm(data, tm); + tm->tm_year -= 1900; + tm->tm_mon -= 1; + immr_unmap(sys_tmr); + return; +} + +void mpc8xx_restart(char *cmd) +{ + __volatile__ unsigned char dummy; + car8xx_t * clk_r = (car8xx_t *) immr_map(im_clkrst); + + + local_irq_disable(); + + setbits32(&clk_r->car_plprcr, 0x00000080); + /* Clear the ME bit in MSR to cause checkstop on machine check + */ + mtmsr(mfmsr() & ~0x1000); + + dummy = in_8(&clk_r->res[0]); + printk("Restart failed\n"); + while(1); +} + +void mpc8xx_show_cpuinfo(struct seq_file *m) +{ + struct device_node *root; + uint memsize = total_memory; + const char *model = ""; + + seq_printf(m, "Vendor\t\t: Freescale Semiconductor\n"); + + root = of_find_node_by_path("/"); + if (root) + model = get_property(root, "model", NULL); + seq_printf(m, "Machine\t\t: %s\n", model); + of_node_put(root); + + seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024)); +} + +static void cpm_cascade(unsigned int irq, struct irq_desc *desc) +{ + int cascade_irq; + + if ((cascade_irq = cpm_get_irq()) >= 0) { + struct irq_desc *cdesc = irq_desc + cascade_irq; + + generic_handle_irq(cascade_irq); + cdesc->chip->eoi(cascade_irq); + } + desc->chip->eoi(irq); +} + +/* Initialize the internal interrupt controller. The number of + * interrupts supported can vary with the processor type, and the + * 82xx family can have up to 64. + * External interrupts can be either edge or level triggered, and + * need to be initialized by the appropriate driver. + */ +void __init m8xx_pic_init(void) +{ + int irq; + + if (mpc8xx_pic_init()) { + printk(KERN_ERR "Failed interrupt 8xx controller initialization\n"); + return; + } + + irq = cpm_pic_init(); + if (irq != NO_IRQ) + set_irq_chained_handler(irq, cpm_cascade); +} diff --git a/arch/powerpc/platforms/8xx/mpc885ads.h b/arch/powerpc/platforms/8xx/mpc885ads.h new file mode 100644 index 00000000000..30cbebfe84c --- /dev/null +++ b/arch/powerpc/platforms/8xx/mpc885ads.h @@ -0,0 +1,95 @@ +/* + * A collection of structures, addresses, and values associated with + * the Freescale MPC885ADS board. + * Copied from the FADS stuff. + * + * Author: MontaVista Software, Inc. + * source@mvista.com + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under the + * terms of the GNU General Public License version 2. This program is licensed + * "as is" without any warranty of any kind, whether express or implied. + */ + +#ifdef __KERNEL__ +#ifndef __ASM_MPC885ADS_H__ +#define __ASM_MPC885ADS_H__ + +#include <asm/ppcboot.h> +#include <sysdev/fsl_soc.h> + +/* U-Boot maps BCSR to 0xff080000 */ +#define BCSR_ADDR ((uint)0xff080000) +#define BCSR_SIZE ((uint)32) +#define BCSR0 ((uint)(BCSR_ADDR + 0x00)) +#define BCSR1 ((uint)(BCSR_ADDR + 0x04)) +#define BCSR2 ((uint)(BCSR_ADDR + 0x08)) +#define BCSR3 ((uint)(BCSR_ADDR + 0x0c)) +#define BCSR4 ((uint)(BCSR_ADDR + 0x10)) + +#define CFG_PHYDEV_ADDR ((uint)0xff0a0000) +#define BCSR5 ((uint)(CFG_PHYDEV_ADDR + 0x300)) + +#define IMAP_ADDR (get_immrbase()) +#define IMAP_SIZE ((uint)(64 * 1024)) + +#define MPC8xx_CPM_OFFSET (0x9c0) +#define CPM_MAP_ADDR (get_immrbase() + MPC8xx_CPM_OFFSET) +#define CPM_IRQ_OFFSET 16 // for compability with cpm_uart driver + +#define PCMCIA_MEM_ADDR (uint)0xff020000) +#define PCMCIA_MEM_SIZE ((uint)(64 * 1024)) + +/* Bits of interest in the BCSRs. + */ +#define BCSR1_ETHEN ((uint)0x20000000) +#define BCSR1_IRDAEN ((uint)0x10000000) +#define BCSR1_RS232EN_1 ((uint)0x01000000) +#define BCSR1_PCCEN ((uint)0x00800000) +#define BCSR1_PCCVCC0 ((uint)0x00400000) +#define BCSR1_PCCVPP0 ((uint)0x00200000) +#define BCSR1_PCCVPP1 ((uint)0x00100000) +#define BCSR1_PCCVPP_MASK (BCSR1_PCCVPP0 | BCSR1_PCCVPP1) +#define BCSR1_RS232EN_2 ((uint)0x00040000) +#define BCSR1_PCCVCC1 ((uint)0x00010000) +#define BCSR1_PCCVCC_MASK (BCSR1_PCCVCC0 | BCSR1_PCCVCC1) + +#define BCSR4_ETH10_RST ((uint)0x80000000) /* 10Base-T PHY reset*/ +#define BCSR4_USB_LO_SPD ((uint)0x04000000) +#define BCSR4_USB_VCC ((uint)0x02000000) +#define BCSR4_USB_FULL_SPD ((uint)0x00040000) +#define BCSR4_USB_EN ((uint)0x00020000) + +#define BCSR5_MII2_EN 0x40 +#define BCSR5_MII2_RST 0x20 +#define BCSR5_T1_RST 0x10 +#define BCSR5_ATM155_RST 0x08 +#define BCSR5_ATM25_RST 0x04 +#define BCSR5_MII1_EN 0x02 +#define BCSR5_MII1_RST 0x01 + +/* Interrupt level assignments */ +#define PHY_INTERRUPT SIU_IRQ7 /* PHY link change interrupt */ +#define SIU_INT_FEC1 SIU_LEVEL1 /* FEC1 interrupt */ +#define SIU_INT_FEC2 SIU_LEVEL3 /* FEC2 interrupt */ +#define FEC_INTERRUPT SIU_INT_FEC1 /* FEC interrupt */ + +/* We don't use the 8259 */ +#define NR_8259_INTS 0 + +/* CPM Ethernet through SCC3 */ +#define PA_ENET_RXD ((ushort)0x0040) +#define PA_ENET_TXD ((ushort)0x0080) +#define PE_ENET_TCLK ((uint)0x00004000) +#define PE_ENET_RCLK ((uint)0x00008000) +#define PE_ENET_TENA ((uint)0x00000010) +#define PC_ENET_CLSN ((ushort)0x0400) +#define PC_ENET_RENA ((ushort)0x0800) + +/* Control bits in the SICR to route TCLK (CLK5) and RCLK (CLK6) to + * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero */ +#define SICR_ENET_MASK ((uint)0x00ff0000) +#define SICR_ENET_CLKRT ((uint)0x002c0000) + +#endif /* __ASM_MPC885ADS_H__ */ +#endif /* __KERNEL__ */ diff --git a/arch/powerpc/platforms/8xx/mpc885ads_setup.c b/arch/powerpc/platforms/8xx/mpc885ads_setup.c new file mode 100644 index 00000000000..c5fefdf66c0 --- /dev/null +++ b/arch/powerpc/platforms/8xx/mpc885ads_setup.c @@ -0,0 +1,387 @@ +/*arch/ppc/platforms/mpc885ads-setup.c + * + * Platform setup for the Freescale mpc885ads board + * + * Vitaly Bordug <vbordug@ru.mvista.com> + * + * Copyright 2005 MontaVista Software Inc. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/param.h> +#include <linux/string.h> +#include <linux/ioport.h> +#include <linux/device.h> +#include <linux/delay.h> +#include <linux/root_dev.h> + +#include <linux/fs_enet_pd.h> +#include <linux/fs_uart_pd.h> +#include <linux/mii.h> + +#include <asm/delay.h> +#include <asm/io.h> +#include <asm/machdep.h> +#include <asm/page.h> +#include <asm/processor.h> +#include <asm/system.h> +#include <asm/time.h> +#include <asm/ppcboot.h> +#include <asm/mpc8xx.h> +#include <asm/8xx_immap.h> +#include <asm/commproc.h> +#include <asm/fs_pd.h> +#include <asm/prom.h> + +extern void cpm_reset(void); +extern void mpc8xx_show_cpuinfo(struct seq_file*); +extern void mpc8xx_restart(char *cmd); +extern void mpc8xx_calibrate_decr(void); +extern int mpc8xx_set_rtc_time(struct rtc_time *tm); +extern void mpc8xx_get_rtc_time(struct rtc_time *tm); +extern void m8xx_pic_init(void); +extern unsigned int mpc8xx_get_irq(void); + +static void init_smc1_uart_ioports(struct fs_uart_platform_info* fpi); +static void init_smc2_uart_ioports(struct fs_uart_platform_info* fpi); +static void init_scc3_ioports(struct fs_platform_info* ptr); + +void __init mpc885ads_board_setup(void) +{ + cpm8xx_t *cp; + unsigned int *bcsr_io; + u8 tmpval8; + +#ifdef CONFIG_FS_ENET + iop8xx_t *io_port; +#endif + + bcsr_io = ioremap(BCSR1, sizeof(unsigned long)); + cp = (cpm8xx_t *)immr_map(im_cpm); + + if (bcsr_io == NULL) { + printk(KERN_CRIT "Could not remap BCSR\n"); + return; + } +#ifdef CONFIG_SERIAL_CPM_SMC1 + clrbits32(bcsr_io, BCSR1_RS232EN_1); + clrbits32(&cp->cp_simode, 0xe0000000 >> 17); /* brg1 */ + tmpval8 = in_8(&(cp->cp_smc[0].smc_smcm)) | (SMCM_RX | SMCM_TX); + out_8(&(cp->cp_smc[0].smc_smcm), tmpval8); + clrbits16(&cp->cp_smc[0].smc_smcmr, SMCMR_REN | SMCMR_TEN); /* brg1 */ +#else + setbits32(bcsr_io,BCSR1_RS232EN_1); + out_be16(&cp->cp_smc[0].smc_smcmr, 0); + out_8(&cp->cp_smc[0].smc_smce, 0); +#endif + +#ifdef CONFIG_SERIAL_CPM_SMC2 + clrbits32(bcsr_io,BCSR1_RS232EN_2); + clrbits32(&cp->cp_simode, 0xe0000000 >> 1); + setbits32(&cp->cp_simode, 0x20000000 >> 1); /* brg2 */ + tmpval8 = in_8(&(cp->cp_smc[1].smc_smcm)) | (SMCM_RX | SMCM_TX); + out_8(&(cp->cp_smc[1].smc_smcm), tmpval8); + clrbits16(&cp->cp_smc[1].smc_smcmr, SMCMR_REN | SMCMR_TEN); + + init_smc2_uart_ioports(0); +#else + setbits32(bcsr_io,BCSR1_RS232EN_2); + out_be16(&cp->cp_smc[1].smc_smcmr, 0); + out_8(&cp->cp_smc[1].smc_smce, 0); +#endif + immr_unmap(cp); + iounmap(bcsr_io); + +#ifdef CONFIG_FS_ENET + /* use MDC for MII (common) */ + io_port = (iop8xx_t*)immr_map(im_ioport); + setbits16(&io_port->iop_pdpar, 0x0080); + clrbits16(&io_port->iop_pddir, 0x0080); + + bcsr_io = ioremap(BCSR5, sizeof(unsigned long)); + clrbits32(bcsr_io,BCSR5_MII1_EN); + clrbits32(bcsr_io,BCSR5_MII1_RST); +#ifndef CONFIG_FC_ENET_HAS_SCC + clrbits32(bcsr_io,BCSR5_MII2_EN); + clrbits32(bcsr_io,BCSR5_MII2_RST); + +#endif + iounmap(bcsr_io); + immr_unmap(io_port); + +#endif +} + + +static void init_fec1_ioports(struct fs_platform_info* ptr) +{ + cpm8xx_t *cp = (cpm8xx_t *)immr_map(im_cpm); + iop8xx_t *io_port = (iop8xx_t *)immr_map(im_ioport); + + /* configure FEC1 pins */ + setbits16(&io_port->iop_papar, 0xf830); + setbits16(&io_port->iop_padir, 0x0830); + clrbits16(&io_port->iop_padir, 0xf000); + + setbits32(&cp->cp_pbpar, 0x00001001); + clrbits32(&cp->cp_pbdir, 0x00001001); + + setbits16(&io_port->iop_pcpar, 0x000c); + clrbits16(&io_port->iop_pcdir, 0x000c); + + setbits32(&cp->cp_pepar, 0x00000003); + setbits32(&cp->cp_pedir, 0x00000003); + clrbits32(&cp->cp_peso, 0x00000003); + clrbits32(&cp->cp_cptr, 0x00000100); + + immr_unmap(io_port); + immr_unmap(cp); +} + + +static void init_fec2_ioports(struct fs_platform_info* ptr) +{ + cpm8xx_t *cp = (cpm8xx_t *)immr_map(im_cpm); + iop8xx_t *io_port = (iop8xx_t *)immr_map(im_ioport); + + /* configure FEC2 pins */ + setbits32(&cp->cp_pepar, 0x0003fffc); + setbits32(&cp->cp_pedir, 0x0003fffc); + clrbits32(&cp->cp_peso, 0x000087fc); + setbits32(&cp->cp_peso, 0x00037800); + clrbits32(&cp->cp_cptr, 0x00000080); + + immr_unmap(io_port); + immr_unmap(cp); +} + +void init_fec_ioports(struct fs_platform_info *fpi) +{ + int fec_no = fs_get_fec_index(fpi->fs_no); + + switch (fec_no) { + case 0: + init_fec1_ioports(fpi); + break; + case 1: + init_fec2_ioports(fpi); + break; + default: + printk(KERN_ERR "init_fec_ioports: invalid FEC number\n"); + return; + } +} + +static void init_scc3_ioports(struct fs_platform_info* fpi) +{ + unsigned *bcsr_io; + iop8xx_t *io_port; + cpm8xx_t *cp; + + bcsr_io = ioremap(BCSR_ADDR, BCSR_SIZE); + io_port = (iop8xx_t *)immr_map(im_ioport); + cp = (cpm8xx_t *)immr_map(im_cpm); + + if (bcsr_io == NULL) { + printk(KERN_CRIT "Could not remap BCSR\n"); + return; + } + + /* Enable the PHY. + */ + clrbits32(bcsr_io+4, BCSR4_ETH10_RST); + udelay(1000); + setbits32(bcsr_io+4, BCSR4_ETH10_RST); + /* Configure port A pins for Txd and Rxd. + */ + setbits16(&io_port->iop_papar, PA_ENET_RXD | PA_ENET_TXD); + clrbits16(&io_port->iop_padir, PA_ENET_RXD | PA_ENET_TXD); + + /* Configure port C pins to enable CLSN and RENA. + */ + clrbits16(&io_port->iop_pcpar, PC_ENET_CLSN | PC_ENET_RENA); + clrbits16(&io_port->iop_pcdir, PC_ENET_CLSN | PC_ENET_RENA); + setbits16(&io_port->iop_pcso, PC_ENET_CLSN | PC_ENET_RENA); + + /* Configure port E for TCLK and RCLK. + */ + setbits32(&cp->cp_pepar, PE_ENET_TCLK | PE_ENET_RCLK); + clrbits32(&cp->cp_pepar, PE_ENET_TENA); + clrbits32(&cp->cp_pedir, + PE_ENET_TCLK | PE_ENET_RCLK | PE_ENET_TENA); + clrbits32(&cp->cp_peso, PE_ENET_TCLK | PE_ENET_RCLK); + setbits32(&cp->cp_peso, PE_ENET_TENA); + + /* Configure Serial Interface clock routing. + * First, clear all SCC bits to zero, then set the ones we want. + */ + clrbits32(&cp->cp_sicr, SICR_ENET_MASK); + setbits32(&cp->cp_sicr, SICR_ENET_CLKRT); + + /* Disable Rx and Tx. SMC1 sshould be stopped if SCC3 eternet are used. + */ + clrbits16(&cp->cp_smc[0].smc_smcmr, SMCMR_REN | SMCMR_TEN); + /* On the MPC885ADS SCC ethernet PHY is initialized in the full duplex mode + * by H/W setting after reset. SCC ethernet controller support only half duplex. + * This discrepancy of modes causes a lot of carrier lost errors. + */ + + /* In the original SCC enet driver the following code is placed at + the end of the initialization */ + setbits32(&cp->cp_pepar, PE_ENET_TENA); + clrbits32(&cp->cp_pedir, PE_ENET_TENA); + setbits32(&cp->cp_peso, PE_ENET_TENA); + + setbits32(bcsr_io+4, BCSR1_ETHEN); + iounmap(bcsr_io); + immr_unmap(io_port); + immr_unmap(cp); +} + +void init_scc_ioports(struct fs_platform_info *fpi) +{ + int scc_no = fs_get_scc_index(fpi->fs_no); + + switch (scc_no) { + case 2: + init_scc3_ioports(fpi); + break; + default: + printk(KERN_ERR "init_scc_ioports: invalid SCC number\n"); + return; + } +} + + + +static void init_smc1_uart_ioports(struct fs_uart_platform_info* ptr) +{ + unsigned *bcsr_io; + cpm8xx_t *cp; + + cp = (cpm8xx_t *)immr_map(im_cpm); + setbits32(&cp->cp_pepar, 0x000000c0); + clrbits32(&cp->cp_pedir, 0x000000c0); + clrbits32(&cp->cp_peso, 0x00000040); + setbits32(&cp->cp_peso, 0x00000080); + immr_unmap(cp); + + bcsr_io = ioremap(BCSR1, sizeof(unsigned long)); + + if (bcsr_io == NULL) { + printk(KERN_CRIT "Could not remap BCSR1\n"); + return; + } + clrbits32(bcsr_io,BCSR1_RS232EN_1); + iounmap(bcsr_io); +} + +static void init_smc2_uart_ioports(struct fs_uart_platform_info* fpi) +{ + unsigned *bcsr_io; + cpm8xx_t *cp; + + cp = (cpm8xx_t *)immr_map(im_cpm); + setbits32(&cp->cp_pepar, 0x00000c00); + clrbits32(&cp->cp_pedir, 0x00000c00); + clrbits32(&cp->cp_peso, 0x00000400); + setbits32(&cp->cp_peso, 0x00000800); + immr_unmap(cp); + + bcsr_io = ioremap(BCSR1, sizeof(unsigned long)); + + if (bcsr_io == NULL) { + printk(KERN_CRIT "Could not remap BCSR1\n"); + return; + } + clrbits32(bcsr_io,BCSR1_RS232EN_2); + iounmap(bcsr_io); +} + +void init_smc_ioports(struct fs_uart_platform_info *data) +{ + int smc_no = fs_uart_id_fsid2smc(data->fs_no); + + switch (smc_no) { + case 0: + init_smc1_uart_ioports(data); + data->brg = data->clk_rx; + break; + case 1: + init_smc2_uart_ioports(data); + data->brg = data->clk_rx; + break; + default: + printk(KERN_ERR "init_scc_ioports: invalid SCC number\n"); + return; + } +} + +int platform_device_skip(char *model, int id) +{ +#ifdef CONFIG_MPC8xx_SECOND_ETH_SCC3 + const char *dev = "FEC"; + int n = 2; +#else + const char *dev = "SCC"; + int n = 3; +#endif + + if (!strcmp(model, dev) && n == id) + return 1; + + return 0; +} + +static void __init mpc885ads_setup_arch(void) +{ + struct device_node *cpu; + + cpu = of_find_node_by_type(NULL, "cpu"); + if (cpu != 0) { + const unsigned int *fp; + + fp = get_property(cpu, "clock-frequency", NULL); + if (fp != 0) + loops_per_jiffy = *fp / HZ; + else + loops_per_jiffy = 50000000 / HZ; + of_node_put(cpu); + } + + cpm_reset(); + + mpc885ads_board_setup(); + + ROOT_DEV = Root_NFS; +} + +static int __init mpc885ads_probe(void) +{ + char *model = of_get_flat_dt_prop(of_get_flat_dt_root(), + "model", NULL); + if (model == NULL) + return 0; + if (strcmp(model, "MPC885ADS")) + return 0; + + return 1; +} + +define_machine(mpc885_ads) { + .name = "MPC885 ADS", + .probe = mpc885ads_probe, + .setup_arch = mpc885ads_setup_arch, + .init_IRQ = m8xx_pic_init, + .show_cpuinfo = mpc8xx_show_cpuinfo, + .get_irq = mpc8xx_get_irq, + .restart = mpc8xx_restart, + .calibrate_decr = mpc8xx_calibrate_decr, + .set_rtc_time = mpc8xx_set_rtc_time, + .get_rtc_time = mpc8xx_get_rtc_time, +}; diff --git a/arch/powerpc/platforms/Makefile b/arch/powerpc/platforms/Makefile index 507d1b98f27..7f03ea9ab36 100644 --- a/arch/powerpc/platforms/Makefile +++ b/arch/powerpc/platforms/Makefile @@ -8,6 +8,7 @@ endif obj-$(CONFIG_PPC_MPC52xx) += 52xx/ obj-$(CONFIG_PPC_CHRP) += chrp/ obj-$(CONFIG_4xx) += 4xx/ +obj-$(CONFIG_PPC_8xx) += 8xx/ obj-$(CONFIG_PPC_83xx) += 83xx/ obj-$(CONFIG_PPC_85xx) += 85xx/ obj-$(CONFIG_PPC_86xx) += 86xx/ |