diff options
| -rw-r--r-- | arch/arm/plat-s3c24xx/include/plat/mci.h | 1 | ||||
| -rw-r--r-- | drivers/mmc/host/Kconfig | 34 | ||||
| -rw-r--r-- | drivers/mmc/host/s3cmci.c | 39 |
3 files changed, 66 insertions, 8 deletions
diff --git a/arch/arm/plat-s3c24xx/include/plat/mci.h b/arch/arm/plat-s3c24xx/include/plat/mci.h index 2d0852ac3b2..f1bd6d4198d 100644 --- a/arch/arm/plat-s3c24xx/include/plat/mci.h +++ b/arch/arm/plat-s3c24xx/include/plat/mci.h @@ -4,6 +4,7 @@ struct s3c24xx_mci_pdata { unsigned int wprotect_invert : 1; unsigned int detect_invert : 1; /* set => detect active high. */ + unsigned int use_dma : 1; unsigned int gpio_detect; unsigned int gpio_wprotect; diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index 7cb057f3f88..cf6a6545240 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -276,6 +276,40 @@ config MMC_S3C If unsure, say N. +choice + prompt "Samsung S3C SD/MMC transfer code" + depends on MMC_S3C + +config MMC_S3C_PIO + bool "Use PIO transfers only" + help + Use PIO to transfer data between memory and the hardware. + + PIO is slower than DMA as it requires CPU instructions to + move the data. This has been the traditional default for + the S3C MCI driver. + +config MMC_S3C_DMA + bool "Use DMA transfers only (EXPERIMENTAL)" + depends on EXPERIMENTAL + help + Use DMA to transfer data between memory and the hardare. + + Currently, the DMA support in this driver seems to not be + working properly and needs to be debugged before this + option is useful. + +config MMC_S3C_PIODMA + bool "Support for both PIO and DMA (EXPERIMENTAL)" + help + Compile both the PIO and DMA transfer routines into the + driver and let the platform select at run-time which one + is best. + + See notes for the DMA option. + +endchoice + config MMC_SDRICOH_CS tristate "MMC/SD driver for Ricoh Bay1Controllers (EXPERIMENTAL)" depends on EXPERIMENTAL && PCI && PCMCIA diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 7660ac4572e..0adf31895f2 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -164,6 +164,25 @@ static void dbg_dumpregs(struct s3cmci_host *host, char *prefix) { } #endif /* CONFIG_MMC_DEBUG */ +/** + * s3cmci_host_usedma - return whether the host is using dma or pio + * @host: The host state + * + * Return true if the host is using DMA to transfer data, else false + * to use PIO mode. Will return static data depending on the driver + * configuration. + */ +static inline bool s3cmci_host_usedma(struct s3cmci_host *host) +{ +#ifdef CONFIG_MMC_S3C_PIO + return false; +#elif defined(CONFIG_MMC_S3C_DMA) + return true; +#else + return host->dodma; +#endif +} + static inline u32 enable_imask(struct s3cmci_host *host, u32 imask) { u32 newmask; @@ -560,7 +579,7 @@ static irqreturn_t s3cmci_irq(int irq, void *dev_id) goto irq_out; } - if (!host->dodma) { + if (!s3cmci_host_usedma(host)) { if ((host->pio_active == XFER_WRITE) && (mci_fsta & S3C2410_SDIFSTA_TFDET)) { @@ -796,7 +815,7 @@ static void finalize_request(struct s3cmci_host *host) if (cmd->data && (cmd->error == 0) && (cmd->data->error == 0)) { - if (host->dodma && (!host->dma_complete)) { + if (s3cmci_host_usedma(host) && (!host->dma_complete)) { dbg(host, dbg_dma, "DMA Missing!\n"); return; } @@ -848,7 +867,7 @@ static void finalize_request(struct s3cmci_host *host) /* If we had an error while transfering data we flush the * DMA channel and the fifo to clear out any garbage. */ if (mrq->data->error != 0) { - if (host->dodma) + if (s3cmci_host_usedma(host)) s3c2410_dma_ctrl(host->dma, S3C2410_DMAOP_FLUSH); if (host->is2440) { @@ -968,7 +987,7 @@ static int s3cmci_setup_data(struct s3cmci_host *host, struct mmc_data *data) dcon = data->blocks & S3C2410_SDIDCON_BLKNUM_MASK; - if (host->dodma) + if (s3cmci_host_usedma(host)) dcon |= S3C2410_SDIDCON_DMAEN; if (host->bus_width == MMC_BUS_WIDTH_4) @@ -1114,7 +1133,7 @@ static void s3cmci_send_request(struct mmc_host *mmc) return; } - if (host->dodma) + if (s3cmci_host_usedma(host)) res = s3cmci_prepare_dma(host, cmd->data); else res = s3cmci_prepare_pio(host, cmd->data); @@ -1398,7 +1417,7 @@ static int s3cmci_state_show(struct seq_file *seq, void *v) seq_printf(seq, "IRQ disabled = %d\n", host->irq_disabled); seq_printf(seq, "IRQ state = %d\n", host->irq_state); seq_printf(seq, "CD IRQ = %d\n", host->irq_cd); - seq_printf(seq, "Do DMA = %d\n", host->dodma); + seq_printf(seq, "Do DMA = %d\n", s3cmci_host_usedma(host)); seq_printf(seq, "SDIIMSK at %d\n", host->sdiimsk); seq_printf(seq, "SDIDATA at %d\n", host->sdidata); @@ -1559,12 +1578,15 @@ static int __devinit s3cmci_probe(struct platform_device *pdev) host->clk_div = 2; } - host->dodma = 0; host->complete_what = COMPLETION_NONE; host->pio_active = XFER_NONE; host->dma = S3CMCI_DMA; +#ifdef CONFIG_MMC_S3C_PIODMA + host->dodma = host->pdata->dma; +#endif + host->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!host->mem) { dev_err(&pdev->dev, @@ -1702,7 +1724,8 @@ static int __devinit s3cmci_probe(struct platform_device *pdev) s3cmci_debugfs_attach(host); platform_set_drvdata(pdev, mmc); - dev_info(&pdev->dev, "initialisation done.\n"); + dev_info(&pdev->dev, "%s - using %s\n", mmc_hostname(mmc), + s3cmci_host_usedma(host) ? "dma" : "pio"); return 0; |