diff options
185 files changed, 5495 insertions, 1986 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index 033a3f3b3ab..d4bfae75c94 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -1560,6 +1560,9 @@ platforms are moved over to use the flattened-device-tree model. network device. This is used by the bootwrapper to interpret MAC addresses passed by the firmware when no information other than indices is available to associate an address with a device. + - phy-connection-type : a string naming the controller/PHY interface type, + i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "tbi", + or "rtbi". Example: ucc@2000 { @@ -1574,6 +1577,7 @@ platforms are moved over to use the flattened-device-tree model. rx-clock = "none"; tx-clock = "clk9"; phy-handle = <212000>; + phy-connection-type = "gmii"; pio-handle = <140001>; }; diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig index 8de5f9ff4ad..67668fdb029 100644 --- a/arch/powerpc/Kconfig +++ b/arch/powerpc/Kconfig @@ -117,6 +117,9 @@ config GENERIC_BUG default y depends on BUG +config SYS_SUPPORTS_APM_EMULATION + bool + # # Powerpc uses the slab allocator to manage its ptes and the # page structs of ptes are used for splitting the page table @@ -136,6 +139,11 @@ config DEFAULT_UIMAGE Used to allow a board to specify it wants a uImage built by default default n +config PPC64_SWSUSP + bool + depends on PPC64 && (BROKEN || (PPC_PMAC64 && EXPERIMENTAL)) + default y + menu "Processor support" choice prompt "Processor Type" @@ -669,7 +677,7 @@ config MCA config PCI bool "PCI support" if 40x || CPM2 || PPC_83xx || PPC_85xx || PPC_86xx \ || PPC_MPC52xx || (EMBEDDED && (PPC_PSERIES || PPC_ISERIES)) \ - || MPC7448HPC2 || PPC_PS3 + || MPC7448HPC2 || PPC_PS3 || PPC_HOLLY default y if !40x && !CPM2 && !8xx && !APUS && !PPC_83xx \ && !PPC_85xx && !PPC_86xx default PCI_PERMEDIA if !4xx && !CPM2 && !8xx && APUS diff --git a/arch/powerpc/Makefile b/arch/powerpc/Makefile index 794992025d8..81a531d84ff 100644 --- a/arch/powerpc/Makefile +++ b/arch/powerpc/Makefile @@ -148,7 +148,7 @@ all: $(KBUILD_IMAGE) CPPFLAGS_vmlinux.lds := -Upowerpc -BOOT_TARGETS = zImage zImage.initrd uImage cuImage +BOOT_TARGETS = zImage zImage.initrd uImage PHONY += $(BOOT_TARGETS) diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile index 3716594ea33..ccd757c193e 100644 --- a/arch/powerpc/boot/Makefile +++ b/arch/powerpc/boot/Makefile @@ -37,13 +37,13 @@ zlib := inffast.c inflate.c inftrees.c zlibheader := inffast.h inffixed.h inflate.h inftrees.h infutil.h zliblinuxheader := zlib.h zconf.h zutil.h -$(addprefix $(obj)/,$(zlib) main.o): $(addprefix $(obj)/,$(zliblinuxheader)) \ - $(addprefix $(obj)/,$(zlibheader)) +$(addprefix $(obj)/,$(zlib) gunzip_util.o main.o): \ + $(addprefix $(obj)/,$(zliblinuxheader)) $(addprefix $(obj)/,$(zlibheader)) src-wlib := string.S crt0.S stdio.c main.c flatdevtree.c flatdevtree_misc.c \ ns16550.c serial.c simple_alloc.c div64.S util.S \ gunzip_util.c elf_util.c $(zlib) devtree.c -src-plat := of.c cuboot-83xx.c cuboot-85xx.c +src-plat := of.c cuboot-83xx.c cuboot-85xx.c holly.c src-boot := $(src-wlib) $(src-plat) empty.c src-boot := $(addprefix $(obj)/, $(src-boot)) @@ -129,7 +129,13 @@ image-$(CONFIG_PPC_CELLEB) += zImage.pseries image-$(CONFIG_PPC_CHRP) += zImage.chrp image-$(CONFIG_PPC_EFIKA) += zImage.chrp image-$(CONFIG_PPC_PMAC) += zImage.pmac -image-$(CONFIG_DEFAULT_UIMAGE) += uImage cuImage +image-$(CONFIG_PPC_HOLLY) += zImage.holly-elf +image-$(CONFIG_DEFAULT_UIMAGE) += uImage + +ifneq ($(CONFIG_DEVICE_TREE),"") +image-$(CONFIG_PPC_83xx) += cuImage.83xx +image-$(CONFIG_PPC_85xx) += cuImage.85xx +endif # For 32-bit powermacs, build the COFF and miboot images # as well as the ELF images. @@ -159,18 +165,21 @@ $(obj)/zImage.ps3: vmlinux $(obj)/zImage.initrd.ps3: vmlinux @echo " WARNING zImage.initrd.ps3 not supported (yet)" +$(obj)/zImage.holly-elf: vmlinux $(wrapperbits) + $(call if_changed,wrap,holly,$(obj)/dts/holly.dts,,) + +$(obj)/zImage.initrd.holly-elf: vmlinux $(wrapperbits) $(obj)/ramdisk.image.gz + $(call if_changed,wrap,holly,$(obj)/dts/holly.dts,,$(obj)/ramdisk.image.gz) + $(obj)/uImage: vmlinux $(wrapperbits) $(call if_changed,wrap,uboot) -cuboot-plat-$(CONFIG_83xx) += 83xx -cuboot-plat-$(CONFIG_85xx) += 85xx -cuboot-plat-y += unknown-platform - +# CONFIG_DEVICE_TREE will have "" around it, make sure to strip them dts = $(if $(shell echo $(CONFIG_DEVICE_TREE) | grep '^/'),\ - ,$(srctree)/$(src)/dts/)$(CONFIG_DEVICE_TREE) + ,$(srctree)/$(src)/dts/)$(CONFIG_DEVICE_TREE:"%"=%) -$(obj)/cuImage: vmlinux $(wrapperbits) - $(call if_changed,wrap,cuboot-$(word 1,$(cuboot-plat-y)),$(dts)) +$(obj)/cuImage.%: vmlinux $(dts) $(wrapperbits) + $(call if_changed,wrap,cuboot-$*,$(dts)) $(obj)/zImage: $(addprefix $(obj)/, $(image-y)) @rm -f $@; ln $< $@ @@ -181,8 +190,7 @@ install: $(CONFIGURE) $(addprefix $(obj)/, $(image-y)) sh -x $(srctree)/$(src)/install.sh "$(KERNELRELEASE)" vmlinux System.map "$(INSTALL_PATH)" $< # anything not in $(targets) -clean-files += $(image-) $(initrd-) zImage zImage.initrd \ - cuImage.elf cuImage.bin.gz +clean-files += $(image-) $(initrd-) zImage zImage.initrd cuImage.* # clean up files cached by wrapper clean-kernel := vmlinux.strip vmlinux.bin diff --git a/arch/powerpc/boot/dts/holly.dts b/arch/powerpc/boot/dts/holly.dts new file mode 100644 index 00000000000..254499b107f --- /dev/null +++ b/arch/powerpc/boot/dts/holly.dts @@ -0,0 +1,198 @@ +/* + * Device Tree Source for IBM Holly (PPC 750CL with TSI controller) + * Copyright 2007, IBM Corporation + * + * Stephen Winiecki <stevewin@us.ibm.com> + * Josh Boyer <jwboyer@linux.vnet.ibm.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without + * any warranty of any kind, whether express or implied. + * + * To build: + * dtc -I dts -O asm -o holly.S -b 0 holly.dts + * dtc -I dts -O dtb -o holly.dtb -b 0 holly.dts + */ + +/ { + model = "41K7339"; + compatible = "ibm,holly"; + #address-cells = <1>; + #size-cells = <1>; + + cpus { + #address-cells = <1>; + #size-cells =<0>; + PowerPC,750CL@0 { + device_type = "cpu"; + reg = <0>; + d-cache-line-size = <20>; + i-cache-line-size = <20>; + d-cache-size = <8000>; + i-cache-size = <8000>; + d-cache-sets = <80>; + i-cache-sets = <80>; + timebase-frequency = <2faf080>; + clock-frequency = <23c34600>; + bus-frequency = <bebc200>; + 32-bit; + }; + }; + + memory@0 { + device_type = "memory"; + reg = <00000000 20000000>; + }; + + tsi109@c0000000 { + device_type = "tsi-bridge"; + compatible = "tsi-bridge"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <00000000 c0000000 00010000>; + reg = <c0000000 00010000>; + + i2c@7000 { + device_type = "i2c"; + compatible = "tsi-i2c"; + interrupt-parent = < &/tsi109@c0000000/pic@7400 >; + interrupts = <e 2>; + reg = <7000 400>; + }; + + mdio@6000 { + device_type = "mdio"; + compatible = "tsi-ethernet"; + + PHY1: ethernet-phy@6000 { + device_type = "ethernet-phy"; + compatible = "bcm54xx"; + reg = <6000 50>; + phy-id = <1>; + }; + + PHY2: ethernet-phy@6400 { + device_type = "ethernet-phy"; + compatible = "bcm54xx"; + reg = <6000 50>; + phy-id = <2>; + }; + }; + + ethernet@6200 { + device_type = "network"; + compatible = "tsi-ethernet"; + #address-cells = <1>; + #size-cells = <0>; + reg = <6000 200>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupt-parent = < &/tsi109@c0000000/pic@7400 >; + interrupts = <10 2>; + phy-handle = <&PHY1>; + }; + + ethernet@6600 { + device_type = "network"; + compatible = "tsi-ethernet"; + #address-cells = <1>; + #size-cells = <0>; + reg = <6400 200>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupt-parent = < &/tsi109@c0000000/pic@7400 >; + interrupts = <11 2>; + phy-handle = <&PHY2>; + }; + + serial@7808 { + device_type = "serial"; + compatible = "ns16550"; + reg = <7808 200>; + virtual-reg = <c0007808>; + clock-frequency = <3F9C6000>; + current-speed = <1c200>; + interrupt-parent = < &/tsi109@c0000000/pic@7400 >; + interrupts = <c 2>; + }; + + serial@7c08 { + device_type = "serial"; + compatible = "ns16550"; + reg = <7c08 200>; + virtual-reg = <c0007c08>; + clock-frequency = <3F9C6000>; + current-speed = <1c200>; + interrupt-parent = < &/tsi109@c0000000/pic@7400 >; + interrupts = <d 2>; + }; + + MPIC: pic@7400 { + device_type = "open-pic"; + compatible = "chrp,open-pic"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <7400 400>; + big-endian; + }; + + pci@1000 { + device_type = "pci"; + compatible = "tsi109"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <1000 1000>; + bus-range = <0 0>; + /*----------------------------------------------------+ + | PCI memory range. + | 01 denotes I/O space + | 02 denotes 32-bit memory space + +----------------------------------------------------*/ + ranges = <02000000 0 40000000 40000000 0 10000000 + 01000000 0 00000000 7e000000 0 00010000>; + clock-frequency = <7f28154>; + interrupt-parent = < &/tsi109@c0000000/pic@7400 >; + interrupts = <17 2>; + interrupt-map-mask = <f800 0 0 7>; + /*----------------------------------------------------+ + | The INTA, INTB, INTC, INTD are shared. + +----------------------------------------------------*/ + interrupt-map = < + 0800 0 0 1 &RT0 24 0 + 0800 0 0 2 &RT0 25 0 + 0800 0 0 3 &RT0 26 0 + 0800 0 0 4 &RT0 27 0 + + 1000 0 0 1 &RT0 25 0 + 1000 0 0 2 &RT0 26 0 + 1000 0 0 3 &RT0 27 0 + 1000 0 0 4 &RT0 24 0 + + 1800 0 0 1 &RT0 26 0 + 1800 0 0 2 &RT0 27 0 + 1800 0 0 3 &RT0 24 0 + 1800 0 0 4 &RT0 25 0 + + 2000 0 0 1 &RT0 27 0 + 2000 0 0 2 &RT0 24 0 + 2000 0 0 3 &RT0 25 0 + 2000 0 0 4 &RT0 26 0 + >; + + RT0: router@1180 { + device_type = "pic-router"; + interrupt-controller; + big-endian; + clock-frequency = <0>; + #address-cells = <0>; + #interrupt-cells = <2>; + interrupts = <17 2>; + interrupt-parent = < &/tsi109@c0000000/pic@7400 >; + }; + }; + }; + + chosen { + linux,stdout-path = "/tsi109@c0000000/serial@7808"; + bootargs = "console=ttyS0,115200"; + }; +}; diff --git a/arch/powerpc/boot/dts/lite5200.dts b/arch/powerpc/boot/dts/lite5200.dts index ba54c6b40a0..e13ac6ef05a 100644 --- a/arch/powerpc/boot/dts/lite5200.dts +++ b/arch/powerpc/boot/dts/lite5200.dts @@ -48,6 +48,7 @@ soc5200@f0000000 { model = "fsl,mpc5200"; + compatible = "mpc5200"; revision = "" // from bootloader #interrupt-cells = <3>; device_type = "soc"; @@ -166,7 +167,7 @@ device_type = "mscan"; compatible = "mpc5200-mscan"; cell-index = <1>; - interrupts = <1 12 0>; + interrupts = <2 12 0>; interrupt-parent = <500>; reg = <980 80>; }; @@ -178,7 +179,7 @@ interrupt-parent = <500>; }; - gpio-wkup@b00 { + gpio-wkup@c00 { compatible = "mpc5200-gpio-wkup"; reg = <c00 40>; interrupts = <1 8 0 0 3 0>; @@ -317,20 +318,22 @@ i2c@3d00 { device_type = "i2c"; - compatible = "mpc5200-i2c"; + compatible = "mpc5200-i2c\0fsl-i2c"; cell-index = <0>; reg = <3d00 40>; interrupts = <2 f 0>; interrupt-parent = <500>; + fsl5200-clocking; }; i2c@3d40 { device_type = "i2c"; - compatible = "mpc5200-i2c"; + compatible = "mpc5200-i2c\0fsl-i2c"; cell-index = <1>; reg = <3d40 40>; interrupts = <2 10 0>; interrupt-parent = <500>; + fsl5200-clocking; }; sram@8000 { device_type = "sram"; diff --git a/arch/powerpc/boot/dts/lite5200b.dts b/arch/powerpc/boot/dts/lite5200b.dts index 2e003081b0d..00211b39a34 100644 --- a/arch/powerpc/boot/dts/lite5200b.dts +++ b/arch/powerpc/boot/dts/lite5200b.dts @@ -48,6 +48,7 @@ soc5200@f0000000 { model = "fsl,mpc5200b"; + compatible = "mpc5200"; revision = ""; // from bootloader #interrupt-cells = <3>; device_type = "soc"; @@ -166,7 +167,7 @@ device_type = "mscan"; compatible = "mpc5200b-mscan\0mpc5200-mscan"; cell-index = <1>; - interrupts = <1 12 0>; + interrupts = <2 12 0>; interrupt-parent = <500>; reg = <980 80>; }; @@ -178,7 +179,7 @@ interrupt-parent = <500>; }; - gpio-wkup@b00 { + gpio-wkup@c00 { compatible = "mpc5200b-gpio-wkup\0mpc5200-gpio-wkup"; reg = <c00 40>; interrupts = <1 8 0 0 3 0>; @@ -322,20 +323,22 @@ i2c@3d00 { device_type = "i2c"; - compatible = "mpc5200b-i2c\0mpc5200-i2c"; + compatible = "mpc5200b-i2c\0mpc5200-i2c\0fsl-i2c"; cell-index = <0>; reg = <3d00 40>; interrupts = <2 f 0>; interrupt-parent = <500>; + fsl5200-clocking; }; i2c@3d40 { device_type = "i2c"; - compatible = "mpc5200b-i2c\0mpc5200-i2c"; + compatible = "mpc5200b-i2c\0mpc5200-i2c\0fsl-i2c"; cell-index = <1>; reg = <3d40 40>; interrupts = <2 10 0>; interrupt-parent = <500>; + fsl5200-clocking; }; sram@8000 { device_type = "sram"; diff --git a/arch/powerpc/boot/dts/mpc832x_mds.dts b/arch/powerpc/boot/dts/mpc832x_mds.dts index c798491f4cd..93b76069601 100644 --- a/arch/powerpc/boot/dts/mpc832x_mds.dts +++ b/arch/powerpc/boot/dts/mpc832x_mds.dts @@ -306,14 +306,12 @@ interrupts = <11 8>; reg = <3>; device_type = "ethernet-phy"; - interface = <3>; //ENET_100_MII }; phy4: ethernet-phy@04 { interrupt-parent = < &ipic >; interrupts = <12 8>; reg = <4>; device_type = "ethernet-phy"; - interface = <3>; }; }; diff --git a/arch/powerpc/boot/dts/mpc832x_rdb.dts b/arch/powerpc/boot/dts/mpc832x_rdb.dts index b55bced1593..be4c35784e4 100644 --- a/arch/powerpc/boot/dts/mpc832x_rdb.dts +++ b/arch/powerpc/boot/dts/mpc832x_rdb.dts @@ -265,14 +265,12 @@ interrupts = <0>; reg = <0>; device_type = "ethernet-phy"; - interface = <3>; //ENET_100_MII }; phy04:ethernet-phy@04 { interrupt-parent = <&pic>; interrupts = <0>; reg = <4>; device_type = "ethernet-phy"; - interface = <3>; }; }; diff --git a/arch/powerpc/boot/dts/mpc836x_mds.dts b/arch/powerpc/boot/dts/mpc836x_mds.dts index 7f578eb5708..38c8594df3a 100644 --- a/arch/powerpc/boot/dts/mpc836x_mds.dts +++ b/arch/powerpc/boot/dts/mpc836x_mds.dts @@ -305,6 +305,7 @@ rx-clock = <0>; tx-clock = <19>; phy-handle = < &phy0 >; + phy-connection-type = "rgmii-id"; pio-handle = < &pio1 >; }; @@ -320,6 +321,7 @@ rx-clock = <0>; tx-clock = <14>; phy-handle = < &phy1 >; + phy-connection-type = "rgmii-id"; pio-handle = < &pio2 >; }; @@ -335,14 +337,12 @@ interrupts = <11 8>; reg = <0>; device_type = "ethernet-phy"; - interface = <6>; //ENET_1000_GMII }; phy1: ethernet-phy@01 { interrupt-parent = < &ipic >; interrupts = <12 8>; reg = <1>; device_type = "ethernet-phy"; - interface = <6>; }; }; diff --git a/arch/powerpc/boot/dts/mpc8568mds.dts b/arch/powerpc/boot/dts/mpc8568mds.dts index 7361b36749c..948a3b61bd4 100644 --- a/arch/powerpc/boot/dts/mpc8568mds.dts +++ b/arch/powerpc/boot/dts/mpc8568mds.dts @@ -288,6 +288,7 @@ rx-clock = <0>; tx-clock = <19>; phy-handle = <&qe_phy0>; + phy-connection-type = "gmii"; pio-handle = <&pio1>; }; @@ -303,6 +304,7 @@ rx-clock = <0>; tx-clock = <14>; phy-handle = <&qe_phy1>; + phy-connection-type = "gmii"; pio-handle = <&pio2>; }; @@ -320,28 +322,24 @@ interrupts = <31 1>; reg = <0>; device_type = "ethernet-phy"; - interface = <6>; //ENET_1000_GMII }; qe_phy1: ethernet-phy@01 { interrupt-parent = <&mpic>; interrupts = <32 1>; reg = <1>; device_type = "ethernet-phy"; - interface = <6>; }; qe_phy2: ethernet-phy@02 { interrupt-parent = <&mpic>; interrupts = <31 1>; reg = <2>; device_type = "ethernet-phy"; - interface = <6>; //ENET_1000_GMII }; qe_phy3: ethernet-phy@03 { interrupt-parent = <&mpic>; interrupts = <32 1>; reg = <3>; device_type = "ethernet-phy"; - interface = <6>; //ENET_1000_GMII }; }; diff --git a/arch/powerpc/boot/holly.c b/arch/powerpc/boot/holly.c new file mode 100644 index 00000000000..7d6539f5e22 --- /dev/null +++ b/arch/powerpc/boot/holly.c @@ -0,0 +1,38 @@ +/* + * Copyright 2007 IBM Corporation + * + * Stephen Winiecki <stevewin@us.ibm.com> + * Josh Boyer <jwboyer@linux.vnet.ibm.com> + * + * Based on earlier code: + * Copyright (C) Paul Mackerras 1997. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + */ +#include <stdarg.h> +#include <stddef.h> +#include "types.h" +#include "elf.h" +#include "string.h" +#include "stdio.h" +#include "page.h" +#include "ops.h" +#include "io.h" + +extern char _start[]; +extern char _end[]; +extern char _dtb_start[]; +extern char _dtb_end[]; + +BSS_STACK(4096); + +void platform_init(unsigned long r3, unsigned long r4, unsigned long r5) +{ + u32 heapsize = 0x8000000 - (u32)_end; /* 128M */ + + simple_alloc_init(_end, heapsize, 32, 64); + ft_init(_dtb_start, 0, 4); + serial_console_init(); +} diff --git a/arch/powerpc/boot/wrapper b/arch/powerpc/boot/wrapper index 5cedd901201..1ea208096b1 100755 --- a/arch/powerpc/boot/wrapper +++ b/arch/powerpc/boot/wrapper @@ -163,20 +163,19 @@ fi vmz="$vmz$gzip" -case "$platform" in -uboot|cuboot*) - version=`${CROSS}strings "$kernel" | grep '^Linux version [-0-9.]' | \ - cut -d' ' -f3` - if [ -n "$version" ]; then - version="-n Linux-$version" - fi -esac +# Extract kernel version information, some platforms want to include +# it in the image header +version=`${CROSS}strings "$kernel" | grep '^Linux version [-0-9.]' | \ + cut -d' ' -f3` +if [ -n "$version" ]; then + uboot_version="-n Linux-$version" +fi case "$platform" in uboot) rm -f "$ofile" mkimage -A ppc -O linux -T kernel -C gzip -a 00000000 -e 00000000 \ - $version -d "$vmz" "$ofile" + $uboot_version -d "$vmz" "$ofile" if [ -z "$cacheit" ]; then rm -f "$vmz" fi @@ -212,25 +211,24 @@ if [ "$platform" != "miboot" ]; then rm $tmp fi +# Some platforms need the zImage's entry point and base address +base=0x`${CROSS}nm "$ofile" | grep ' _start$' | cut -d' ' -f1` +entry=`${CROSS}objdump -f "$ofile" | grep '^start address ' | cut -d' ' -f3` + # post-processing needed for some platforms case "$platform" in pseries|chrp) $object/addnote "$ofile" ;; pmaccoff) - entry=`objdump -f "$ofile" | grep '^start address ' | \ - cut -d' ' -f3` ${CROSS}objcopy -O aixcoff-rs6000 --set-start "$entry" "$ofile" $object/hack-coff "$ofile" ;; cuboot*) - base=`${CROSS}nm "$ofile" | grep ' _start$' | cut -d' ' -f1` - entry=`${CROSS}objdump -f "$ofile" | grep '^start address ' | \ - cut -d' ' -f3` mv "$ofile" "$ofile".elf ${CROSS}objcopy -O binary "$ofile".elf "$ofile".bin gzip -f -9 "$ofile".bin mkimage -A ppc -O linux -T kernel -C gzip -a "$base" -e "$entry" \ - $version -d "$ofile".bin.gz "$ofile" + $uboot_version -d "$ofile".bin.gz "$ofile" ;; esac diff --git a/arch/powerpc/configs/holly_defconfig b/arch/powerpc/configs/holly_defconfig new file mode 100644 index 00000000000..be633b9b57c --- /dev/null +++ b/arch/powerpc/configs/holly_defconfig @@ -0,0 +1,1070 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.21 +# Sat May 5 11:02:35 2007 +# +# CONFIG_PPC64 is not set +CONFIG_PPC32=y +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_IRQ_PER_CPU=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_ARCH_HAS_ILOG2_U32=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +CONFIG_PPC_UDBG_16550=y +# CONFIG_GENERIC_TBSYNC is not set +CONFIG_AUDIT_ARCH=y +CONFIG_GENERIC_BUG=y +# CONFIG_DEFAULT_UIMAGE is not set + +# +# Processor support +# +CONFIG_CLASSIC32=y +# CONFIG_PPC_82xx is not set +# CONFIG_PPC_83xx is not set +# CONFIG_PPC_85xx is not set +# CONFIG_PPC_86xx is not set +# CONFIG_PPC_8xx is not set +# CONFIG_40x is not set +# CONFIG_44x is not set +# CONFIG_E200 is not set +CONFIG_6xx=y +CONFIG_PPC_FPU=y +# CONFIG_PPC_DCR_NATIVE is not set +# CONFIG_PPC_DCR_MMIO is not set +# CONFIG_ALTIVEC is not set +CONFIG_PPC_STD_MMU=y +CONFIG_PPC_STD_MMU_32=y +# CONFIG_SMP is not set +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +# CONFIG_IPC_NS is not set +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_UTS_NS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_SYSFS_DEPRECATED=y +# CONFIG_RELAY is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_SLAB=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set + +# +# Loadable module support +# +CONFIG_MODULES=y +# CONFIG_MODULE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +# CONFIG_KMOD is not set + +# +# Block layer +# +CONFIG_BLOCK=y +CONFIG_LBD=y +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# Platform support +# +# CONFIG_PPC_MULTIPLATFORM is not set +CONFIG_EMBEDDED6xx=y +# CONFIG_APUS is not set +# CONFIG_PPC_MPC52xx is not set +# CONFIG_PPC_MPC5200 is not set +# CONFIG_PPC_CELL is not set +# CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PQ2ADS is not set +# CONFIG_LINKSTATION is not set +# CONFIG_MPC7448HPC2 is not set +CONFIG_PPC_HOLLY=y +CONFIG_TSI108_BRIDGE=y +CONFIG_MPIC=y +CONFIG_MPIC_WEIRD=y +# CONFIG_PPC_I8259 is not set +# CONFIG_PPC_RTAS is not set +# CONFIG_MMIO_NVRAM is not set +# CONFIG_PPC_MPC106 is not set +# CONFIG_PPC_970_NAP is not set +# CONFIG_PPC_INDIRECT_IO is not set +# CONFIG_GENERIC_IOMAP is not set +# CONFIG_CPU_FREQ is not set +# CONFIG_TAU is not set +# CONFIG_CPM2 is not set + +# +# Kernel options +# +# CONFIG_HIGHMEM is not set +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_300 is not set +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_BINFMT_ELF=y +CONFIG_BINFMT_MISC=y +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_PROC_DEVICETREE=y +# CONFIG_CMDLINE_BOOL is not set +# CONFIG_PM is not set +# CONFIG_SECCOMP is not set +# CONFIG_WANT_DEVICE_TREE is not set +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +CONFIG_ZONE_DMA=y +CONFIG_GENERIC_ISA_DMA=y +# CONFIG_PPC_INDIRECT_PCI is not set +CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y +# CONFIG_PCIEPORTBUS is not set +# CONFIG_PCI_DEBUG is not set + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# PCI Hotplug Support +# +# CONFIG_HOTPLUG_PCI is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_HIGHMEM_START=0xfe000000 +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_TASK_SIZE=0x80000000 +CONFIG_BOOT_LOAD=0x00800000 + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +CONFIG_XFRM_USER=y +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set +# CONFIG_MTD is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# +# CONFIG_PNPACPI is not set + +# +# Block devices +# +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_SX8 is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=131072 +CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# Misc devices +# +# CONFIG_SGI_IOC4 is not set +# CONFIG_TIFM_CORE is not set + +# +# ATA/ATAPI/MFM/RLL support +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set + +# +# SCSI low-level drivers +# +# CONFIG_ISCSI_TCP is not set +# CONFIG_BLK_DEV_3W_XXXX_RAID is not set +# CONFIG_SCSI_3W_9XXX is not set +# CONFIG_SCSI_ACARD is not set +# CONFIG_SCSI_AACRAID is not set +# CONFIG_SCSI_AIC7XXX is not set +# CONFIG_SCSI_AIC7XXX_OLD is not set +# CONFIG_SCSI_AIC79XX is not set +# CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ARCMSR is not set +# CONFIG_MEGARAID_NEWGEN is not set +# CONFIG_MEGARAID_LEGACY is not set +# CONFIG_MEGARAID_SAS is not set +# CONFIG_SCSI_HPTIOP is not set +# CONFIG_SCSI_BUSLOGIC is not set +# CONFIG_SCSI_DMX3191D is not set +# CONFIG_SCSI_EATA is not set +# CONFIG_SCSI_FUTURE_DOMAIN is not set +# CONFIG_SCSI_GDTH is not set +# CONFIG_SCSI_IPS is not set +# CONFIG_SCSI_INITIO is not set +# CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_STEX is not set +# CONFIG_SCSI_SYM53C8XX_2 is not set +# CONFIG_SCSI_IPR is not set +# CONFIG_SCSI_QLOGIC_1280 is not set +# CONFIG_SCSI_QLA_FC is not set +# CONFIG_SCSI_QLA_ISCSI is not set +# CONFIG_SCSI_LPFC is not set +# CONFIG_SCSI_DC395x is not set +# CONFIG_SCSI_DC390T is not set +# CONFIG_SCSI_NSP32 is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_ESP_CORE is not set +# CONFIG_SCSI_SRP is not set + +# +# Serial ATA (prod) and Parallel ATA (experimental) drivers +# +CONFIG_ATA=y +# CONFIG_ATA_NONSTANDARD is not set +# CONFIG_SATA_AHCI is not set +# CONFIG_SATA_SVW is not set +# CONFIG_ATA_PIIX is not set +# CONFIG_SATA_MV is not set +# CONFIG_SATA_NV is not set +# CONFIG_PDC_ADMA is not set +# CONFIG_SATA_QSTOR is not set +# CONFIG_SATA_PROMISE is not set +# CONFIG_SATA_SX4 is not set +# CONFIG_SATA_SIL is not set +# CONFIG_SATA_SIL24 is not set +# CONFIG_SATA_SIS is not set +# CONFIG_SATA_ULI is not set +# CONFIG_SATA_VIA is not set +# CONFIG_SATA_VITESSE is not set +# CONFIG_SATA_INIC162X is not set +# CONFIG_PATA_ALI is not set +# CONFIG_PATA_AMD is not set +# CONFIG_PATA_ARTOP is not set +# CONFIG_PATA_ATIIXP is not set +# CONFIG_PATA_CMD640_PCI is not set +# CONFIG_PATA_CMD64X is not set +# CONFIG_PATA_CS5520 is not set +# CONFIG_PATA_CS5530 is not set +# CONFIG_PATA_CYPRESS is not set +# CONFIG_PATA_EFAR is not set +# CONFIG_ATA_GENERIC is not set +# CONFIG_PATA_HPT366 is not set +# CONFIG_PATA_HPT37X is not set +# CONFIG_PATA_HPT3X2N is not set +# CONFIG_PATA_HPT3X3 is not set +# CONFIG_PATA_IT821X is not set +# CONFIG_PATA_IT8213 is not set +# CONFIG_PATA_JMICRON is not set +# CONFIG_PATA_TRIFLEX is not set +# CONFIG_PATA_MARVELL is not set +# CONFIG_PATA_MPIIX is not set +# CONFIG_PATA_OLDPIIX is not set +# CONFIG_PATA_NETCELL is not set +# CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_OPTI is not set +# CONFIG_PATA_OPTIDMA is not set +# CONFIG_PATA_PDC_OLD is not set +# CONFIG_PATA_RADISYS is not set +# CONFIG_PATA_RZ1000 is not set +# CONFIG_PATA_SC1200 is not set +# CONFIG_PATA_SERVERWORKS is not set +# CONFIG_PATA_PDC2027X is not set +# CONFIG_PATA_SIL680 is not set +# CONFIG_PATA_SIS is not set +# CONFIG_PATA_VIA is not set +# CONFIG_PATA_WINBOND is not set +# CONFIG_PATA_PLATFORM is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set +# CONFIG_FUSION_SPI is not set +# CONFIG_FUSION_FC is not set +# CONFIG_FUSION_SAS is not set + +# +# IEEE 1394 (FireWire) support +# +# CONFIG_IEEE1394 is not set + +# +# I2O device support +# +# CONFIG_I2O is not set +# CONFIG_MACINTOSH_DRIVERS is not set + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# ARCnet devices +# +# CONFIG_ARCNET is not set + +# +# PHY device support +# +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_FIXED_PHY is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_CASSINI is not set +CONFIG_NET_VENDOR_3COM=y +CONFIG_VORTEX=y +# CONFIG_TYPHOON is not set + +# +# Tulip family network device support +# +# CONFIG_NET_TULIP is not set +# CONFIG_HP100 is not set +# CONFIG_NET_PCI is not set + +# +# Ethernet (1000 Mbit) +# +# CONFIG_ACENIC is not set +# CONFIG_DL2K is not set +# CONFIG_E1000 is not set +# CONFIG_NS83820 is not set +# CONFIG_HAMACHI is not set +# CONFIG_YELLOWFIN is not set +# CONFIG_R8169 is not set +# CONFIG_SIS190 is not set +# CONFIG_SKGE is not set +# CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set +# CONFIG_TIGON3 is not set +# CONFIG_BNX2 is not set +CONFIG_TSI108_ETH=y +# CONFIG_QLA3XXX is not set +# CONFIG_ATL1 is not set + +# +# Ethernet (10000 Mbit) +# +# CONFIG_CHELSIO_T1 is not set +# CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGB is not set +# CONFIG_S2IO is not set +# CONFIG_MYRI10GE is not set +# CONFIG_NETXEN_NIC is not set + +# +# Token Ring devices +# +# CONFIG_TR is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NET_FC is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Telephony Support +# +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_VT is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +# CONFIG_SERIAL_8250_PCI is not set +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SERIAL_8250_EXTENDED=y +# CONFIG_SERIAL_8250_MANY_PORTS is not set +CONFIG_SERIAL_8250_SHARE_IRQ=y +# CONFIG_SERIAL_8250_DETECT_IRQ is not set +# CONFIG_SERIAL_8250_RSA is not set + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set +CONFIG_SERIAL_OF_PLATFORM=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +# CONFIG_WATCHDOG is not set +# CONFIG_HW_RANDOM is not set +# CONFIG_NVRAM is not set +CONFIG_GEN_RTC=y +# CONFIG_GEN_RTC_X is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set + +# +# I2C support +# +# CONFIG_I2C is not set + +# +# SPI support +# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Hardware Monitoring support +# +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_ABITUGURU is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_PC87427 is not set +# CONFIG_SENSORS_VT1211 is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set + +# +# Graphics support +# +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set +# CONFIG_FB is not set +# CONFIG_FB_IBM_GXT4500 is not set + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# HID Devices +# +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +# CONFIG_USB is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# USB Gadget Support +# +# CONFIG_USB_GADGET is not set + +# +# MMC/SD Card support +# +# CONFIG_MMC is not set + +# +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# +# InfiniBand support +# +# CONFIG_INFINIBAND is not set + +# +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock +# +# CONFIG_RTC_CLASS is not set + +# +# DMA Engine support +# +# CONFIG_DMA_ENGINE is not set + +# +# DMA Clients +# + +# +# DMA Devices +# + +# +# Auxiliary Display support +# + +# +# Virtualization +# + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +CONFIG_EXT3_FS_XATTR=y +# CONFIG_EXT3_FS_POSIX_ACL is not set +# CONFIG_EXT3_FS_SECURITY is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=y +# CONFIG_JBD_DEBUG is not set +CONFIG_FS_MBCACHE=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +CONFIG_NFS_FS=y +# CONFIG_NFS_V3 is not set +# CONFIG_NFS_V4 is not set +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set + +# +# Native Language Support +# +# CONFIG_NLS is not set + +# +# Distributed Lock Manager +# +# CONFIG_DLM is not set +# CONFIG_UCC_SLOW is not set +# CONFIG_UCC_FAST is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y + +# +# Instrumentation Support +# +# CONFIG_PROFILING is not set +# CONFIG_KPROBES is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_LIST is not set +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_DEBUG_STACKOVERFLOW is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_PAGEALLOC is not set +CONFIG_DEBUGGER=y +CONFIG_XMON=y +CONFIG_XMON_DEFAULT=y +CONFIG_XMON_DISASSEMBLY=y +# CONFIG_BDI_SWITCH is not set +# CONFIG_BOOTX_TEXT is not set +# CONFIG_PPC_EARLY_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +# CONFIG_CRYPTO is not set diff --git a/arch/powerpc/configs/mpc832x_mds_defconfig b/arch/powerpc/configs/mpc832x_mds_defconfig index e1b36de6b38..83192c0dc5b 100644 --- a/arch/powerpc/configs/mpc832x_mds_defconfig +++ b/arch/powerpc/configs/mpc832x_mds_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.20-rc5 -# Tue Jan 30 14:27:25 2007 +# Linux kernel version: 2.6.21-rc5 +# Mon Apr 9 16:09:16 2007 # # CONFIG_PPC64 is not set CONFIG_PPC32=y @@ -34,9 +34,9 @@ CONFIG_DEFAULT_UIMAGE=y CONFIG_PPC_83xx=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_86xx is not set +# CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set -# CONFIG_8xx is not set # CONFIG_E200 is not set CONFIG_6xx=y CONFIG_83xx=y @@ -63,6 +63,7 @@ CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y # CONFIG_IPC_NS is not set +CONFIG_SYSVIPC_SYSCTL=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set @@ -71,6 +72,7 @@ CONFIG_SYSVIPC=y # CONFIG_IKCONFIG is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set +CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_SYSCTL=y @@ -123,16 +125,17 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_QUICC_ENGINE=y -CONFIG_PPC_GEN550=y # CONFIG_WANT_EARLY_SERIAL is not set # # Platform support # +# CONFIG_MPC8313_RDB is not set CONFIG_MPC832x_MDS=y -# CONFIG_MPC834x_SYS is not set +# CONFIG_MPC832x_RDB is not set +# CONFIG_MPC834x_MDS is not set # CONFIG_MPC834x_ITX is not set -# CONFIG_MPC8360E_PB is not set +# CONFIG_MPC836x_MDS is not set CONFIG_PPC_MPC832x=y # CONFIG_MPIC is not set @@ -163,6 +166,7 @@ CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set @@ -172,6 +176,7 @@ CONFIG_ISA_DMA_API=y # # Bus options # +CONFIG_ZONE_DMA=y CONFIG_GENERIC_ISA_DMA=y # CONFIG_MPIC_WEIRD is not set # CONFIG_PPC_I8259 is not set @@ -220,6 +225,7 @@ CONFIG_UNIX=y CONFIG_XFRM=y # CONFIG_XFRM_USER is not set # CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set # CONFIG_NET_KEY is not set CONFIG_INET=y CONFIG_IP_MULTICAST=y @@ -324,6 +330,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # # Plug and Play support # +# CONFIG_PNPACPI is not set # # Block devices @@ -342,7 +349,6 @@ CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=32768 CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 -CONFIG_BLK_DEV_INITRD=y # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set @@ -482,7 +488,21 @@ CONFIG_NETDEVICES=y # # PHY device support # -# CONFIG_PHYLIB is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +CONFIG_DAVICOM_PHY=y +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_FIXED_PHY is not set # # Ethernet (10 or 100Mbit) @@ -524,11 +544,13 @@ CONFIG_UCC_GETH=y # CONFIG_UGETH_FILTERING is not set # CONFIG_UGETH_TX_ON_DEMOND is not set # CONFIG_QLA3XXX is not set +# CONFIG_ATL1 is not set # # Ethernet (10000 Mbit) # # CONFIG_CHELSIO_T1 is not set +# CONFIG_CHELSIO_T3 is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set @@ -621,6 +643,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y # CONFIG_SERIAL_JSM is not set +# CONFIG_SERIAL_OF_PLATFORM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -691,6 +714,7 @@ CONFIG_I2C_MPC=y # CONFIG_I2C_NFORCE2 is not set # CONFIG_I2C_OCORES is not set # CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_PASEMI is not set # CONFIG_I2C_PROSAVAGE is not set # CONFIG_I2C_SAVAGE4 is not set # CONFIG_I2C_SIS5595 is not set @@ -738,6 +762,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set # CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set # CONFIG_SENSORS_ASB100 is not set @@ -779,6 +804,11 @@ CONFIG_HWMON=y # CONFIG_HWMON_DEBUG_CHIP is not set # +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set + +# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -791,10 +821,9 @@ CONFIG_HWMON=y # # Graphics support # -CONFIG_FIRMWARE_EDID=y +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set # CONFIG_FB is not set # CONFIG_FB_IBM_GXT4500 is not set -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Sound @@ -805,6 +834,7 @@ CONFIG_FIRMWARE_EDID=y # HID Devices # CONFIG_HID=y +# CONFIG_HID_DEBUG is not set # # USB support @@ -869,6 +899,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y # # +# Auxiliary Display support +# + +# # Virtualization # @@ -995,11 +1029,7 @@ CONFIG_PARTITION_ADVANCED=y # Distributed Lock Manager # # CONFIG_DLM is not set - -# -# QE Options -# -CONFIG_UCC_SLOW=y +# CONFIG_UCC_SLOW is not set CONFIG_UCC_FAST=y CONFIG_UCC=y @@ -1012,7 +1042,8 @@ CONFIG_BITREVERSE=y CONFIG_CRC32=y # CONFIG_LIBCRC32C is not set CONFIG_PLIST=y -CONFIG_IOMAP_COPY=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y # # Instrumentation Support @@ -1032,7 +1063,6 @@ CONFIG_ENABLE_MUST_CHECK=y CONFIG_LOG_BUF_SHIFT=14 # CONFIG_DEBUG_BUGVERBOSE is not set # CONFIG_BOOTX_TEXT is not set -# CONFIG_SERIAL_TEXT_DEBUG is not set # CONFIG_PPC_EARLY_DEBUG is not set # @@ -1061,8 +1091,10 @@ CONFIG_CRYPTO_MD5=y # CONFIG_CRYPTO_GF128MUL is not set CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y +CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set # CONFIG_CRYPTO_BLOWFISH is not set # CONFIG_CRYPTO_TWOFISH is not set # CONFIG_CRYPTO_SERPENT is not set @@ -1076,6 +1108,7 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set # diff --git a/arch/powerpc/configs/mpc832x_rdb_defconfig b/arch/powerpc/configs/mpc832x_rdb_defconfig index 56fc0a82445..4a4da875fa4 100644 --- a/arch/powerpc/configs/mpc832x_rdb_defconfig +++ b/arch/powerpc/configs/mpc832x_rdb_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.21-rc3 -# Mon Mar 12 17:32:19 2007 +# Linux kernel version: 2.6.21-rc5 +# Mon Apr 9 16:12:43 2007 # # CONFIG_PPC64 is not set CONFIG_PPC32=y @@ -125,7 +125,6 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_QUICC_ENGINE=y -CONFIG_PPC_GEN550=y # CONFIG_WANT_EARLY_SERIAL is not set # @@ -490,7 +489,21 @@ CONFIG_NETDEVICES=y # # PHY device support # -# CONFIG_PHYLIB is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +CONFIG_ICPLUS_PHY=y +# CONFIG_FIXED_PHY is not set # # Ethernet (10 or 100Mbit) @@ -1200,11 +1213,7 @@ CONFIG_NLS_ISO8859_1=y # Distributed Lock Manager # # CONFIG_DLM is not set - -# -# QE Options -# -CONFIG_UCC_SLOW=y +# CONFIG_UCC_SLOW is not set CONFIG_UCC_FAST=y CONFIG_UCC=y @@ -1238,7 +1247,6 @@ CONFIG_ENABLE_MUST_CHECK=y CONFIG_LOG_BUF_SHIFT=14 # CONFIG_DEBUG_BUGVERBOSE is not set # CONFIG_BOOTX_TEXT is not set -# CONFIG_SERIAL_TEXT_DEBUG is not set # CONFIG_PPC_EARLY_DEBUG is not set # diff --git a/arch/powerpc/configs/mpc836x_mds_defconfig b/arch/powerpc/configs/mpc836x_mds_defconfig index 8eb475cd0df..921a151dc77 100644 --- a/arch/powerpc/configs/mpc836x_mds_defconfig +++ b/arch/powerpc/configs/mpc836x_mds_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.20 -# Sat Feb 17 10:09:26 2007 +# Linux kernel version: 2.6.21-rc5 +# Mon Apr 9 16:14:05 2007 # # CONFIG_PPC64 is not set CONFIG_PPC32=y @@ -72,6 +72,7 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_IKCONFIG is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set +CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_SYSCTL=y @@ -124,7 +125,6 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_QUICC_ENGINE=y -CONFIG_PPC_GEN550=y # CONFIG_WANT_EARLY_SERIAL is not set # @@ -132,6 +132,7 @@ CONFIG_PPC_GEN550=y # # CONFIG_MPC8313_RDB is not set # CONFIG_MPC832x_MDS is not set +# CONFIG_MPC832x_RDB is not set # CONFIG_MPC834x_MDS is not set # CONFIG_MPC834x_ITX is not set CONFIG_MPC836x_MDS=y @@ -328,6 +329,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # # Plug and Play support # +# CONFIG_PNPACPI is not set # # Block devices @@ -346,7 +348,6 @@ CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=32768 CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 -CONFIG_BLK_DEV_INITRD=y # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set @@ -486,7 +487,21 @@ CONFIG_NETDEVICES=y # # PHY device support # -# CONFIG_PHYLIB is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +CONFIG_MARVELL_PHY=y +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_FIXED_PHY is not set # # Ethernet (10 or 100Mbit) @@ -528,6 +543,7 @@ CONFIG_UCC_GETH=y # CONFIG_UGETH_FILTERING is not set # CONFIG_UGETH_TX_ON_DEMOND is not set # CONFIG_QLA3XXX is not set +# CONFIG_ATL1 is not set # # Ethernet (10000 Mbit) @@ -745,6 +761,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set # CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set # CONFIG_SENSORS_ASB100 is not set @@ -786,6 +803,11 @@ CONFIG_HWMON=y # CONFIG_HWMON_DEBUG_CHIP is not set # +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set + +# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -798,10 +820,9 @@ CONFIG_HWMON=y # # Graphics support # -CONFIG_FIRMWARE_EDID=y +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set # CONFIG_FB is not set # CONFIG_FB_IBM_GXT4500 is not set -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Sound @@ -1007,11 +1028,7 @@ CONFIG_PARTITION_ADVANCED=y # Distributed Lock Manager # # CONFIG_DLM is not set - -# -# QE Options -# -CONFIG_UCC_SLOW=y +# CONFIG_UCC_SLOW is not set CONFIG_UCC_FAST=y CONFIG_UCC=y @@ -1045,7 +1062,6 @@ CONFIG_ENABLE_MUST_CHECK=y CONFIG_LOG_BUF_SHIFT=14 # CONFIG_DEBUG_BUGVERBOSE is not set # CONFIG_BOOTX_TEXT is not set -# CONFIG_SERIAL_TEXT_DEBUG is not set # CONFIG_PPC_EARLY_DEBUG is not set # diff --git a/arch/powerpc/configs/ps3_defconfig b/arch/powerpc/configs/ps3_defconfig index 0345a2ceec5..fd604968f9a 100644 --- a/arch/powerpc/configs/ps3_defconfig +++ b/arch/powerpc/configs/ps3_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.20-rc6 -# Thu Jan 25 13:35:34 2007 +# Linux kernel version: 2.6.21 +# Mon Apr 30 12:03:35 2007 # CONFIG_PPC64=y CONFIG_64BIT=y @@ -60,6 +60,7 @@ CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y # CONFIG_IPC_NS is not set +CONFIG_SYSVIPC_SYSCTL=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set @@ -69,6 +70,7 @@ CONFIG_SYSVIPC=y # CONFIG_CPUSETS is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set +CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="" CONFIG_CC_OPTIMIZE_FOR_SIZE=y CONFIG_SYSCTL=y @@ -131,13 +133,36 @@ CONFIG_PPC_MULTIPLATFORM=y # CONFIG_PPC_PSERIES is not set # CONFIG_PPC_ISERIES is not set # CONFIG_PPC_MPC52xx is not set +# CONFIG_PPC_MPC5200 is not set # CONFIG_PPC_PMAC is not set # CONFIG_PPC_MAPLE is not set # CONFIG_PPC_PASEMI is not set +# CONFIG_PPC_CELLEB is not set +CONFIG_PPC_PS3=y + +# +# PS3 Platform Options +# +# CONFIG_PS3_ADVANCED is not set +CONFIG_PS3_HTAB_SIZE=20 +# CONFIG_PS3_DYNAMIC_DMA is not set +CONFIG_PS3_USE_LPAR_ADDR=y +CONFIG_PS3_VUART=y +CONFIG_PS3_PS3AV=y +CONFIG_PS3_SYS_MANAGER=y CONFIG_PPC_CELL=y # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_IBM_CELL_BLADE is not set -CONFIG_PPC_PS3=y + +# +# Cell Broadband Engine options +# +CONFIG_SPU_FS=y +CONFIG_SPU_BASE=y +# CONFIG_PQ2ADS is not set +# CONFIG_MPIC is not set +# CONFIG_MPIC_WEIRD is not set +# CONFIG_PPC_I8259 is not set # CONFIG_U3_DART is not set # CONFIG_PPC_RTAS is not set # CONFIG_MMIO_NVRAM is not set @@ -146,24 +171,7 @@ CONFIG_PPC_PS3=y # CONFIG_PPC_INDIRECT_IO is not set # CONFIG_GENERIC_IOMAP is not set # CONFIG_CPU_FREQ is not set -# CONFIG_WANT_EARLY_SERIAL is not set -# CONFIG_MPIC is not set - -# -# Cell Broadband Engine options -# -CONFIG_SPU_FS=y -CONFIG_SPU_BASE=y -# CONFIG_CBE_RAS is not set - -# -# PS3 Platform Options -# -CONFIG_PS3_HTAB_SIZE=20 -# CONFIG_PS3_DYNAMIC_DMA is not set -CONFIG_PS3_USE_LPAR_ADDR=y -CONFIG_PS3_VUART=y -CONFIG_PS3_PS3AV=y +# CONFIG_CPM2 is not set # # Kernel options @@ -179,10 +187,10 @@ CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_BKL is not set CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y -CONFIG_FORCE_MAX_ZONEORDER=9 +CONFIG_FORCE_MAX_ZONEORDER=13 # CONFIG_IOMMU_VMERGE is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y -# CONFIG_KEXEC is not set +CONFIG_KEXEC=y # CONFIG_CRASH_DUMP is not set # CONFIG_IRQ_ALL_CPUS is not set # CONFIG_NUMA is not set @@ -203,22 +211,22 @@ CONFIG_MEMORY_HOTPLUG=y CONFIG_MEMORY_HOTPLUG_SPARSE=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_RESOURCES_64BIT=y +CONFIG_ZONE_DMA_FLAG=1 CONFIG_ARCH_MEMORY_PROBE=y -CONFIG_PPC_64K_PAGES=y +# CONFIG_PPC_64K_PAGES is not set # CONFIG_SCHED_SMT is not set CONFIG_PROC_DEVICETREE=y -CONFIG_CMDLINE_BOOL=y -CONFIG_CMDLINE="root=/dev/sda1 ip=dhcp" +# CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set # CONFIG_SECCOMP is not set +# CONFIG_WANT_DEVICE_TREE is not set CONFIG_ISA_DMA_API=y # # Bus options # +CONFIG_ZONE_DMA=y CONFIG_GENERIC_ISA_DMA=y -# CONFIG_MPIC_WEIRD is not set -# CONFIG_PPC_I8259 is not set # CONFIG_PCI is not set # CONFIG_PCI_DOMAINS is not set @@ -240,10 +248,13 @@ CONFIG_NET=y # # Networking options # -# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set # CONFIG_NET_KEY is not set CONFIG_INET=y # CONFIG_IP_MULTICAST is not set @@ -261,7 +272,7 @@ CONFIG_IP_PNP_DHCP=y # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set # CONFIG_INET_XFRM_TUNNEL is not set -# CONFIG_INET_TUNNEL is not set +CONFIG_INET_TUNNEL=y # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set @@ -270,9 +281,23 @@ CONFIG_IP_PNP_DHCP=y CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IPV6 is not set +CONFIG_IPV6=y +# CONFIG_IPV6_PRIVACY is not set +# CONFIG_IPV6_ROUTER_PREF is not set +# CONFIG_IPV6_OPTIMISTIC_DAD is not set +# CONFIG_INET6_AH is not set +# CONFIG_INET6_ESP is not set +# CONFIG_INET6_IPCOMP is not set +# CONFIG_IPV6_MIP6 is not set # CONFIG_INET6_XFRM_TUNNEL is not set # CONFIG_INET6_TUNNEL is not set +CONFIG_INET6_XFRM_MODE_TRANSPORT=y +CONFIG_INET6_XFRM_MODE_TUNNEL=y +CONFIG_INET6_XFRM_MODE_BEET=y +# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set +CONFIG_IPV6_SIT=y +# CONFIG_IPV6_TUNNEL is not set +# CONFIG_IPV6_MULTIPLE_TABLES is not set # CONFIG_NETWORK_SECMARK is not set # CONFIG_NETFILTER is not set @@ -313,7 +338,31 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set # CONFIG_IRDA is not set -# CONFIG_BT is not set +CONFIG_BT=m +CONFIG_BT_L2CAP=m +CONFIG_BT_SCO=m +CONFIG_BT_RFCOMM=m +# CONFIG_BT_RFCOMM_TTY is not set +# CONFIG_BT_BNEP is not set +CONFIG_BT_HIDP=m + +# +# Bluetooth device drivers +# +CONFIG_BT_HCIUSB=m +CONFIG_BT_HCIUSB_SCO=y +# CONFIG_BT_HCIUART is not set +# CONFIG_BT_HCIBCM203X is not set +# CONFIG_BT_HCIBPA10X is not set +# CONFIG_BT_HCIBFUSB is not set +# CONFIG_BT_HCIVHCI is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +CONFIG_WIRELESS_EXT=y # CONFIG_IEEE80211 is not set # @@ -327,16 +376,13 @@ CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set # CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set # CONFIG_SYS_HYPERVISOR is not set # # Connector - unified userspace <-> kernelspace linker # # CONFIG_CONNECTOR is not set - -# -# Memory Technology Devices (MTD) -# # CONFIG_MTD is not set # @@ -347,24 +393,27 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # # Plug and Play support # +# CONFIG_PNPACPI is not set # # Block devices # # CONFIG_BLK_DEV_FD is not set # CONFIG_BLK_DEV_COW_COMMON is not set -# CONFIG_BLK_DEV_LOOP is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_UB is not set -# CONFIG_BLK_DEV_RAM is not set -# CONFIG_BLK_DEV_INITRD is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=65535 +CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set # # Misc devices # -# CONFIG_TIFM_CORE is not set # # ATA/ATAPI/MFM/RLL support @@ -388,7 +437,7 @@ CONFIG_BLK_DEV_SD=y # CONFIG_CHR_DEV_OSST is not set CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set -# CONFIG_CHR_DEV_SG is not set +CONFIG_CHR_DEV_SG=m # CONFIG_CHR_DEV_SCH is not set # @@ -413,6 +462,7 @@ CONFIG_BLK_DEV_SR=y # # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_ESP_CORE is not set # # Serial ATA (prod) and Parallel ATA (experimental) drivers @@ -460,7 +510,7 @@ CONFIG_NETDEVICES=y # Ethernet (10 or 100Mbit) # # CONFIG_NET_ETHERNET is not set -CONFIG_MII=y +CONFIG_MII=m # # Ethernet (1000 Mbit) @@ -475,9 +525,10 @@ CONFIG_MII=y # # -# Wireless LAN (non-hamradio) +# Wireless LAN # -# CONFIG_NET_RADIO is not set +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set # # Wan interfaces @@ -551,7 +602,8 @@ CONFIG_HW_CONSOLE=y # Non-8250 serial port support # CONFIG_UNIX98_PTYS=y -# CONFIG_LEGACY_PTYS is not set +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=16 # # IPMI @@ -598,6 +650,11 @@ CONFIG_GEN_RTC=y # CONFIG_HWMON_VID is not set # +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set + +# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -611,15 +668,22 @@ CONFIG_GEN_RTC=y # # Graphics support # -# CONFIG_FIRMWARE_EDID is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set CONFIG_FB=y +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB_DDC is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_SVGALIB is not set # CONFIG_FB_MACMODES is not set # CONFIG_FB_BACKLIGHT is not set # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# # CONFIG_FB_OF is not set # CONFIG_FB_VGA16 is not set # CONFIG_FB_S1D13XXX is not set @@ -634,7 +698,7 @@ CONFIG_FB_PS3_DEFAULT_SIZE_M=18 # CONFIG_VGA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y -# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set +CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y # CONFIG_FONTS is not set CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y @@ -646,17 +710,62 @@ CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set # CONFIG_LOGO_LINUX_VGA16 is not set CONFIG_LOGO_LINUX_CLUT224=y -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Sound # -# CONFIG_SOUND is not set +CONFIG_SOUND=y + +# +# Advanced Linux Sound Architecture +# +CONFIG_SND=y +# CONFIG_SND_SEQUENCER is not set +# CONFIG_SND_MIXER_OSS is not set +# CONFIG_SND_PCM_OSS is not set +# CONFIG_SND_DYNAMIC_MINORS is not set +CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set + +# +# Generic devices +# +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set + +# +# ALSA PowerMac devices +# + +# +# ALSA PowerMac requires I2C +# + +# +# USB devices +# +# CONFIG_SND_USB_AUDIO is not set +# CONFIG_SND_USB_USX2Y is not set + +# +# SoC audio support +# +# CONFIG_SND_SOC is not set + +# +# Open Sound System +# +# CONFIG_SOUND_PRIME is not set # # HID Devices # CONFIG_HID=y +# CONFIG_HID_DEBUG is not set # # USB support @@ -665,13 +774,13 @@ CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y -CONFIG_USB_DEBUG=y +# CONFIG_USB_DEBUG is not set # # Miscellaneous USB options # -# CONFIG_USB_DEVICEFS is not set -# CONFIG_USB_BANDWIDTH is not set +CONFIG_USB_DEVICEFS=y +# CONFIG_USB_DEVICE_CLASS is not set # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_OTG is not set @@ -704,7 +813,7 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y # # may also be needed; see USB_STORAGE Help for more information # -CONFIG_USB_STORAGE=y +CONFIG_USB_STORAGE=m # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set @@ -720,10 +829,16 @@ CONFIG_USB_STORAGE=y # # USB Input Devices # -CONFIG_USB_HID=y +CONFIG_USB_HID=m # CONFIG_USB_HIDINPUT_POWERBOOK is not set # CONFIG_HID_FF is not set # CONFIG_USB_HIDDEV is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set # CONFIG_USB_AIPTEK is not set # CONFIG_USB_WACOM is not set # CONFIG_USB_ACECAD is not set @@ -736,6 +851,7 @@ CONFIG_USB_HID=y # CONFIG_USB_ATI_REMOTE2 is not set # CONFIG_USB_KEYSPAN_REMOTE is not set # CONFIG_USB_APPLETOUCH is not set +# CONFIG_USB_GTCO is not set # # USB Imaging devices @@ -748,15 +864,16 @@ CONFIG_USB_HID=y # # CONFIG_USB_CATC is not set # CONFIG_USB_KAWETH is not set -# CONFIG_USB_PEGASUS is not set +CONFIG_USB_PEGASUS=m # CONFIG_USB_RTL8150 is not set -CONFIG_USB_USBNET_MII=y -CONFIG_USB_USBNET=y -CONFIG_USB_NET_CDCETHER=y +CONFIG_USB_USBNET_MII=m +CONFIG_USB_USBNET=m +# CONFIG_USB_NET_CDCETHER is not set +# CONFIG_USB_NET_DM9601 is not set # CONFIG_USB_NET_GL620A is not set # CONFIG_USB_NET_NET1080 is not set # CONFIG_USB_NET_PLUSB is not set -CONFIG_USB_NET_MCS7830=y +CONFIG_USB_NET_MCS7830=m # CONFIG_USB_NET_RNDIS_HOST is not set # CONFIG_USB_NET_CDC_SUBSET is not set # CONFIG_USB_NET_ZAURUS is not set @@ -781,6 +898,7 @@ CONFIG_USB_MON=y # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set # CONFIG_USB_LED is not set # CONFIG_USB_CYPRESS_CY7C63 is not set # CONFIG_USB_CYTHERM is not set @@ -791,6 +909,8 @@ CONFIG_USB_MON=y # CONFIG_USB_SISUSBVGA is not set # CONFIG_USB_LD is not set # CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set # # USB DSL modem support @@ -846,13 +966,19 @@ CONFIG_USB_MON=y # # +# Auxiliary Display support +# + +# # Virtualization # # # File systems # -# CONFIG_EXT2_FS is not set +CONFIG_EXT2_FS=m +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_POSIX_ACL is not set @@ -871,27 +997,30 @@ CONFIG_FS_MBCACHE=y # CONFIG_ROMFS_FS is not set CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y -# CONFIG_QUOTA is not set +CONFIG_QUOTA=y +# CONFIG_QFMT_V1 is not set +CONFIG_QFMT_V2=y +CONFIG_QUOTACTL=y CONFIG_DNOTIFY=y # CONFIG_AUTOFS_FS is not set -# CONFIG_AUTOFS4_FS is not set +CONFIG_AUTOFS4_FS=y # CONFIG_FUSE_FS is not set # # CD-ROM/DVD Filesystems # -CONFIG_ISO9660_FS=y +CONFIG_ISO9660_FS=m CONFIG_JOLIET=y # CONFIG_ZISOFS is not set -CONFIG_UDF_FS=y +CONFIG_UDF_FS=m CONFIG_UDF_NLS=y # # DOS/FAT/NT Filesystems # -CONFIG_FAT_FS=y +CONFIG_FAT_FS=m # CONFIG_MSDOS_FS is not set -CONFIG_VFAT_FS=y +CONFIG_VFAT_FS=m CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" # CONFIG_NTFS_FS is not set @@ -933,7 +1062,7 @@ CONFIG_RAMFS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set -# CONFIG_NFS_V4 is not set +CONFIG_NFS_V4=y # CONFIG_NFS_DIRECTIO is not set # CONFIG_NFSD is not set CONFIG_ROOT_NFS=y @@ -941,10 +1070,16 @@ CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y -# CONFIG_RPCSEC_GSS_KRB5 is not set +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set -# CONFIG_CIFS is not set +CONFIG_CIFS=m +# CONFIG_CIFS_STATS is not set +# CONFIG_CIFS_WEAK_PW_HASH is not set +# CONFIG_CIFS_XATTR is not set +# CONFIG_CIFS_DEBUG2 is not set +# CONFIG_CIFS_EXPERIMENTAL is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set @@ -1004,6 +1139,8 @@ CONFIG_NLS_ISO8859_1=y # Distributed Lock Manager # # CONFIG_DLM is not set +# CONFIG_UCC_SLOW is not set +# CONFIG_UCC_FAST is not set # # Library routines @@ -1014,7 +1151,8 @@ CONFIG_BITREVERSE=y CONFIG_CRC32=y # CONFIG_LIBCRC32C is not set CONFIG_PLIST=y -CONFIG_IOMAP_COPY=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y # # Instrumentation Support @@ -1032,16 +1170,16 @@ CONFIG_ENABLE_MUST_CHECK=y # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set CONFIG_LOG_BUF_SHIFT=17 CONFIG_DETECT_SOFTLOCKUP=y # CONFIG_SCHEDSTATS is not set -CONFIG_DEBUG_SLAB=y -# CONFIG_DEBUG_SLAB_LEAK is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_SLAB is not set # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_RT_MUTEX_TESTER is not set CONFIG_DEBUG_SPINLOCK=y CONFIG_DEBUG_MUTEXES=y -CONFIG_DEBUG_RWSEMS=y CONFIG_DEBUG_SPINLOCK_SLEEP=y # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1051,8 +1189,10 @@ CONFIG_DEBUG_INFO=y CONFIG_DEBUG_LIST=y CONFIG_FORCED_INLINING=y # CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_FAULT_INJECTION is not set CONFIG_DEBUG_STACKOVERFLOW=y # CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_PAGEALLOC is not set # CONFIG_DEBUGGER is not set CONFIG_IRQSTACKS=y # CONFIG_BOOTX_TEXT is not set @@ -1063,6 +1203,8 @@ CONFIG_PPC_EARLY_DEBUG=y # CONFIG_PPC_EARLY_DEBUG_RTAS_CONSOLE is not set # CONFIG_PPC_EARLY_DEBUG_MAPLE is not set # CONFIG_PPC_EARLY_DEBUG_ISERIES is not set +# CONFIG_PPC_EARLY_DEBUG_PAS_REALMODE is not set +# CONFIG_PPC_EARLY_DEBUG_BEAT is not set # # Security options @@ -1073,4 +1215,43 @@ CONFIG_PPC_EARLY_DEBUG=y # # Cryptographic options # -# CONFIG_CRYPTO is not set +CONFIG_CRYPTO=y +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_WP512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_GF128MUL is not set +CONFIG_CRYPTO_ECB=m +CONFIG_CRYPTO_CBC=y +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_TWOFISH is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Hardware crypto devices +# diff --git a/arch/powerpc/kernel/Makefile b/arch/powerpc/kernel/Makefile index aa693d0f151..94c703a9501 100644 --- a/arch/powerpc/kernel/Makefile +++ b/arch/powerpc/kernel/Makefile @@ -36,8 +36,9 @@ obj-$(CONFIG_GENERIC_TBSYNC) += smp-tbsync.o obj-$(CONFIG_CRASH_DUMP) += crash_dump.o obj-$(CONFIG_6xx) += idle_6xx.o l2cr_6xx.o cpu_setup_6xx.o obj-$(CONFIG_TAU) += tau_6xx.o +obj-$(CONFIG_SOFTWARE_SUSPEND) += swsusp.o suspend.o obj32-$(CONFIG_SOFTWARE_SUSPEND) += swsusp_32.o -obj-$(CONFIG_SOFTWARE_SUSPEND) += suspend.o +obj64-$(CONFIG_SOFTWARE_SUSPEND) += swsusp_64.o swsusp_asm64.o obj32-$(CONFIG_MODULES) += module_32.o ifeq ($(CONFIG_PPC_MERGE),y) diff --git a/arch/powerpc/kernel/asm-offsets.c b/arch/powerpc/kernel/asm-offsets.c index 0c5150c6917..8f48560b7ee 100644 --- a/arch/powerpc/kernel/asm-offsets.c +++ b/arch/powerpc/kernel/asm-offsets.c @@ -21,12 +21,12 @@ #include <linux/types.h> #include <linux/mman.h> #include <linux/mm.h> +#include <linux/suspend.h> #ifdef CONFIG_PPC64 #include <linux/time.h> #include <linux/hardirq.h> #else #include <linux/ptrace.h> -#include <linux/suspend.h> #endif #include <asm/io.h> @@ -257,11 +257,11 @@ int main(void) DEFINE(CPU_SPEC_SETUP, offsetof(struct cpu_spec, cpu_setup)); DEFINE(CPU_SPEC_RESTORE, offsetof(struct cpu_spec, cpu_restore)); -#ifndef CONFIG_PPC64 DEFINE(pbe_address, offsetof(struct pbe, address)); DEFINE(pbe_orig_address, offsetof(struct pbe, orig_address)); DEFINE(pbe_next, offsetof(struct pbe, next)); +#ifndef CONFIG_PPC64 DEFINE(TASK_SIZE, TASK_SIZE); DEFINE(NUM_USER_SEGMENTS, TASK_SIZE>>28); #endif /* ! CONFIG_PPC64 */ diff --git a/arch/powerpc/kernel/head_44x.S b/arch/powerpc/kernel/head_44x.S index a15d4b8cce4..9ee6773cf02 100644 --- a/arch/powerpc/kernel/head_44x.S +++ b/arch/powerpc/kernel/head_44x.S @@ -120,8 +120,8 @@ skpinv: addi r4,r4,1 /* Increment */ * Configure and load pinned entry into TLB slot 63. */ - lis r3,KERNELBASE@h /* Load the kernel virtual address */ - ori r3,r3,KERNELBASE@l + lis r3,PAGE_OFFSET@h + ori r3,r3,PAGE_OFFSET@l /* Kernel is at the base of RAM */ li r4, 0 /* Load the kernel physical address */ diff --git a/arch/powerpc/kernel/idle.c b/arch/powerpc/kernel/idle.c index 6e7f50967ba..a9e9cbd3297 100644 --- a/arch/powerpc/kernel/idle.c +++ b/arch/powerpc/kernel/idle.c @@ -33,8 +33,11 @@ #include <asm/smp.h> #ifdef CONFIG_HOTPLUG_CPU +/* this is used for software suspend, and that shuts down + * CPUs even while the system is still booting... */ #define cpu_should_die() (cpu_is_offline(smp_processor_id()) && \ - system_state == SYSTEM_RUNNING) + (system_state == SYSTEM_RUNNING \ + || system_state == SYSTEM_BOOTING)) #else #define cpu_should_die() 0 #endif diff --git a/arch/powerpc/kernel/idle_power4.S b/arch/powerpc/kernel/idle_power4.S index ba319547860..5328709eeed 100644 --- a/arch/powerpc/kernel/idle_power4.S +++ b/arch/powerpc/kernel/idle_power4.S @@ -53,3 +53,24 @@ END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC) isync b 1b +_GLOBAL(power4_cpu_offline_powersave) + /* Go to NAP now */ + mfmsr r7 + rldicl r0,r7,48,1 + rotldi r0,r0,16 + mtmsrd r0,1 /* hard-disable interrupts */ + li r0,1 + li r6,0 + stb r0,PACAHARDIRQEN(r13) /* we'll hard-enable shortly */ + stb r6,PACASOFTIRQEN(r13) /* soft-disable irqs */ +BEGIN_FTR_SECTION + DSSALL + sync +END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC) + ori r7,r7,MSR_EE + oris r7,r7,MSR_POW@h + sync + isync + mtmsrd r7 + isync + blr diff --git a/arch/powerpc/kernel/irq.c b/arch/powerpc/kernel/irq.c index 6c83fe229e6..5719a530f2d 100644 --- a/arch/powerpc/kernel/irq.c +++ b/arch/powerpc/kernel/irq.c @@ -67,6 +67,7 @@ #ifdef CONFIG_PPC64 #include <asm/paca.h> #include <asm/firmware.h> +#include <asm/lv1call.h> #endif int __irq_offset_value; @@ -162,6 +163,16 @@ void local_irq_restore(unsigned long en) local_paca->hard_enabled = en; if ((int)mfspr(SPRN_DEC) < 0) mtspr(SPRN_DEC, 1); + + /* + * Force the delivery of pending soft-disabled interrupts on PS3. + * Any HV call will have this side effect. + */ + if (firmware_has_feature(FW_FEATURE_PS3_LV1)) { + u64 tmp; + lv1_get_version_info(&tmp); + } + hard_irq_enable(); } #endif /* CONFIG_PPC64 */ diff --git a/arch/powerpc/kernel/kprobes.c b/arch/powerpc/kernel/kprobes.c index ef647e7a9dc..c27f41870c8 100644 --- a/arch/powerpc/kernel/kprobes.c +++ b/arch/powerpc/kernel/kprobes.c @@ -410,7 +410,7 @@ out: return 1; } -static int __kprobes kprobe_fault_handler(struct pt_regs *regs, int trapnr) +int __kprobes kprobe_fault_handler(struct pt_regs *regs, int trapnr) { struct kprobe *cur = kprobe_running(); struct kprobe_ctlblk *kcb = get_kprobe_ctlblk(); @@ -495,14 +495,6 @@ int __kprobes kprobe_exceptions_notify(struct notifier_block *self, if (post_kprobe_handler(args->regs)) ret = NOTIFY_STOP; break; - case DIE_PAGE_FAULT: - /* kprobe_running() needs smp_processor_id() */ - preempt_disable(); - if (kprobe_running() && - kprobe_fault_handler(args->regs, args->trapnr)) - ret = NOTIFY_STOP; - preempt_enable(); - break; default: break; } diff --git a/arch/powerpc/kernel/legacy_serial.c b/arch/powerpc/kernel/legacy_serial.c index ae4836ea744..cea8045ba40 100644 --- a/arch/powerpc/kernel/legacy_serial.c +++ b/arch/powerpc/kernel/legacy_serial.c @@ -244,9 +244,9 @@ static int __init add_legacy_pci_port(struct device_node *np, * doesn't work for these settings, you'll have to add your own special * cases here */ - if (device_is_compatible(pci_dev, "pci13a8,152") || - device_is_compatible(pci_dev, "pci13a8,154") || - device_is_compatible(pci_dev, "pci13a8,158")) { + if (of_device_is_compatible(pci_dev, "pci13a8,152") || + of_device_is_compatible(pci_dev, "pci13a8,154") || + of_device_is_compatible(pci_dev, "pci13a8,158")) { addr += 0x200 * lindex; base += 0x200 * lindex; } else { @@ -365,11 +365,11 @@ void __init find_legacy_serial_ports(void) /* Check for known pciclass, and also check wether we have * a device with child nodes for ports or not */ - if (device_is_compatible(np, "pciclass,0700") || - device_is_compatible(np, "pciclass,070002")) + if (of_device_is_compatible(np, "pciclass,0700") || + of_device_is_compatible(np, "pciclass,070002")) pci = np; - else if (device_is_compatible(parent, "pciclass,0700") || - device_is_compatible(parent, "pciclass,070002")) + else if (of_device_is_compatible(parent, "pciclass,0700") || + of_device_is_compatible(parent, "pciclass,070002")) pci = parent; else { of_node_put(parent); diff --git a/arch/powerpc/kernel/of_device.c b/arch/powerpc/kernel/of_device.c index 0c8ea7659d9..a464d67248d 100644 --- a/arch/powerpc/kernel/of_device.c +++ b/arch/powerpc/kernel/of_device.c @@ -27,7 +27,7 @@ const struct of_device_id *of_match_node(const struct of_device_id *matches, match &= node->type && !strcmp(matches->type, node->type); if (matches->compatible[0]) - match &= device_is_compatible(node, + match &= of_device_is_compatible(node, matches->compatible); if (match) return matches; @@ -120,8 +120,8 @@ void of_device_unregister(struct of_device *ofdev) } -static ssize_t of_device_get_modalias(struct of_device *ofdev, - char *str, ssize_t len) +ssize_t of_device_get_modalias(struct of_device *ofdev, + char *str, ssize_t len) { const char *compat; int cplen, i; @@ -239,3 +239,4 @@ EXPORT_SYMBOL(of_dev_get); EXPORT_SYMBOL(of_dev_put); EXPORT_SYMBOL(of_release_dev); EXPORT_SYMBOL(of_device_uevent); +EXPORT_SYMBOL(of_device_get_modalias); diff --git a/arch/powerpc/kernel/pci_32.c b/arch/powerpc/kernel/pci_32.c index f022862de34..e66064b5093 100644 --- a/arch/powerpc/kernel/pci_32.c +++ b/arch/powerpc/kernel/pci_32.c @@ -1658,7 +1658,7 @@ pgprot_t pci_phys_mem_access_prot(struct file *file, int i; if (page_is_ram(pfn)) - return prot; + return __pgprot(prot); prot |= _PAGE_NO_CACHE | _PAGE_GUARDED; diff --git a/arch/powerpc/kernel/pci_64.c b/arch/powerpc/kernel/pci_64.c index 7138092826a..6d05a1f377b 100644 --- a/arch/powerpc/kernel/pci_64.c +++ b/arch/powerpc/kernel/pci_64.c @@ -1006,8 +1006,9 @@ void __devinit pci_process_bridge_OF_ranges(struct pci_controller *hose, switch ((pci_space >> 24) & 0x3) { case 1: /* I/O space */ - hose->io_base_phys = cpu_phys_addr; - hose->pci_io_size = size; + hose->io_base_phys = cpu_phys_addr - pci_addr; + /* handle from 0 to top of I/O window */ + hose->pci_io_size = pci_addr + size; res = &hose->io_resource; res->flags = IORESOURCE_IO; @@ -1117,8 +1118,8 @@ static int get_bus_io_range(struct pci_bus *bus, unsigned long *start_phys, } else { /* Root Bus */ res = &hose->io_resource; - *start_phys = hose->io_base_phys; - *start_virt = (unsigned long) hose->io_base_virt; + *start_phys = hose->io_base_phys + res->start; + *start_virt = (unsigned long) hose->io_base_virt + res->start; if (res->end > res->start) *size = res->end - res->start + 1; else { diff --git a/arch/powerpc/kernel/ppc_ksyms.c b/arch/powerpc/kernel/ppc_ksyms.c index ff252aaead1..c96fa9bd35a 100644 --- a/arch/powerpc/kernel/ppc_ksyms.c +++ b/arch/powerpc/kernel/ppc_ksyms.c @@ -66,7 +66,6 @@ EXPORT_SYMBOL(clear_pages); EXPORT_SYMBOL(ISA_DMA_THRESHOLD); EXPORT_SYMBOL(DMA_MODE_READ); EXPORT_SYMBOL(DMA_MODE_WRITE); -EXPORT_SYMBOL(__div64_32); EXPORT_SYMBOL(do_signal); EXPORT_SYMBOL(transfer_to_handler); diff --git a/arch/powerpc/kernel/prom_init.c b/arch/powerpc/kernel/prom_init.c index e27d9d1b6e6..eee3555ced7 100644 --- a/arch/powerpc/kernel/prom_init.c +++ b/arch/powerpc/kernel/prom_init.c @@ -967,7 +967,7 @@ static unsigned long __init prom_next_cell(int s, cell_t **cellp) * If problems seem to show up, it would be a good start to track * them down. */ -static void reserve_mem(u64 base, u64 size) +static void __init reserve_mem(u64 base, u64 size) { u64 top = base + size; unsigned long cnt = RELOC(mem_reserve_cnt); @@ -2153,7 +2153,7 @@ static void __init fixup_device_tree_efika(void) 3,12,0, 3,13,0, 3,14,0, 3,15,0 }; struct subst_entry efika_subst_table[] = { { "/", "device_type", prop_cstr("efika") }, - { "/builtin", "compatible", prop_cstr("soc") }, + { "/builtin", "device_type", prop_cstr("soc") }, { "/builtin/ata", "compatible", prop_cstr("mpc5200b-ata\0mpc5200-ata"), }, { "/builtin/bestcomm", "compatible", prop_cstr("mpc5200b-bestcomm\0mpc5200-bestcomm") }, { "/builtin/bestcomm", "interrupts", prop_bcomm_irq, sizeof(prop_bcomm_irq) }, diff --git a/arch/powerpc/kernel/prom_parse.c b/arch/powerpc/kernel/prom_parse.c index aa40a530729..b5c96af955c 100644 --- a/arch/powerpc/kernel/prom_parse.c +++ b/arch/powerpc/kernel/prom_parse.c @@ -1042,3 +1042,28 @@ const void *of_get_mac_address(struct device_node *np) } EXPORT_SYMBOL(of_get_mac_address); +int of_irq_to_resource(struct device_node *dev, int index, struct resource *r) +{ + int irq = irq_of_parse_and_map(dev, index); + + /* Only dereference the resource if both the + * resource and the irq are valid. */ + if (r && irq != NO_IRQ) { + r->start = r->end = irq; + r->flags = IORESOURCE_IRQ; + } + + return irq; +} +EXPORT_SYMBOL_GPL(of_irq_to_resource); + +void __iomem *of_iomap(struct device_node *np, int index) +{ + struct resource res; + + if (of_address_to_resource(np, index, &res)) + return NULL; + + return ioremap(res.start, 1 + res.end - res.start); +} +EXPORT_SYMBOL(of_iomap); diff --git a/arch/powerpc/kernel/smp.c b/arch/powerpc/kernel/smp.c index d8e503b2e1a..22f1ef1b310 100644 --- a/arch/powerpc/kernel/smp.c +++ b/arch/powerpc/kernel/smp.c @@ -176,10 +176,10 @@ static struct call_data_struct { #define SMP_CALL_TIMEOUT 8 /* - * This function sends a 'generic call function' IPI to all other CPUs - * in the system. + * These functions send a 'generic call function' IPI to other online + * CPUS in the system. * - * [SUMMARY] Run a function on all other CPUs. + * [SUMMARY] Run a function on other CPUs. * <func> The function to run. This must be fast and non-blocking. * <info> An arbitrary pointer to pass to the function. * <nonatomic> currently unused. @@ -190,18 +190,26 @@ static struct call_data_struct { * You must not call this function with disabled interrupts or from a * hardware interrupt handler or from a bottom half handler. */ -int smp_call_function (void (*func) (void *info), void *info, int nonatomic, - int wait) -{ +int smp_call_function_map(void (*func) (void *info), void *info, int nonatomic, + int wait, cpumask_t map) +{ struct call_data_struct data; - int ret = -1, cpus; + int ret = -1, num_cpus; + int cpu; u64 timeout; /* Can deadlock when called with interrupts disabled */ WARN_ON(irqs_disabled()); + /* remove 'self' from the map */ + if (cpu_isset(smp_processor_id(), map)) + cpu_clear(smp_processor_id(), map); + + /* sanity check the map, remove any non-online processors. */ + cpus_and(map, map, cpu_online_map); + if (unlikely(smp_ops == NULL)) - return -1; + return ret; data.func = func; data.info = info; @@ -213,40 +221,42 @@ int smp_call_function (void (*func) (void *info), void *info, int nonatomic, spin_lock(&call_lock); /* Must grab online cpu count with preempt disabled, otherwise * it can change. */ - cpus = num_online_cpus() - 1; - if (!cpus) { + num_cpus = num_online_cpus() - 1; + if (!num_cpus || cpus_empty(map)) { ret = 0; goto out; } call_data = &data; smp_wmb(); - /* Send a message to all other CPUs and wait for them to respond */ - smp_ops->message_pass(MSG_ALL_BUT_SELF, PPC_MSG_CALL_FUNCTION); + /* Send a message to all CPUs in the map */ + for_each_cpu_mask(cpu, map) + smp_ops->message_pass(cpu, PPC_MSG_CALL_FUNCTION); timeout = get_tb() + (u64) SMP_CALL_TIMEOUT * tb_ticks_per_sec; - /* Wait for response */ - while (atomic_read(&data.started) != cpus) { + /* Wait for indication that they have received the message */ + while (atomic_read(&data.started) != num_cpus) { HMT_low(); if (get_tb() >= timeout) { printk("smp_call_function on cpu %d: other cpus not " - "responding (%d)\n", smp_processor_id(), - atomic_read(&data.started)); + "responding (%d)\n", smp_processor_id(), + atomic_read(&data.started)); debugger(NULL); goto out; } } + /* optionally wait for the CPUs to complete */ if (wait) { - while (atomic_read(&data.finished) != cpus) { + while (atomic_read(&data.finished) != num_cpus) { HMT_low(); if (get_tb() >= timeout) { printk("smp_call_function on cpu %d: other " - "cpus not finishing (%d/%d)\n", - smp_processor_id(), - atomic_read(&data.finished), - atomic_read(&data.started)); + "cpus not finishing (%d/%d)\n", + smp_processor_id(), + atomic_read(&data.finished), + atomic_read(&data.started)); debugger(NULL); goto out; } @@ -262,8 +272,29 @@ int smp_call_function (void (*func) (void *info), void *info, int nonatomic, return ret; } +int smp_call_function(void (*func) (void *info), void *info, int nonatomic, + int wait) +{ + return smp_call_function_map(func,info,nonatomic,wait,cpu_online_map); +} EXPORT_SYMBOL(smp_call_function); +int smp_call_function_single(int cpu, void (*func) (void *info), void *info, int nonatomic, + int wait) +{ + cpumask_t map=CPU_MASK_NONE; + + if (!cpu_online(cpu)) + return -EINVAL; + + if (cpu == smp_processor_id()) + return -EBUSY; + + cpu_set(cpu, map); + return smp_call_function_map(func,info,nonatomic,wait,map); +} +EXPORT_SYMBOL(smp_call_function_single); + void smp_call_function_interrupt(void) { void (*func) (void *info); diff --git a/arch/powerpc/kernel/swsusp.c b/arch/powerpc/kernel/swsusp.c new file mode 100644 index 00000000000..064a7ba4f02 --- /dev/null +++ b/arch/powerpc/kernel/swsusp.c @@ -0,0 +1,43 @@ +/* + * Common powerpc suspend code for 32 and 64 bits + * + * Copyright 2007 Johannes Berg <johannes@sipsolutions.net> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#include <linux/sched.h> +#include <asm/suspend.h> +#include <asm/system.h> +#include <asm/current.h> +#include <asm/mmu_context.h> + +void save_processor_state(void) +{ + /* + * flush out all the special registers so we don't need + * to save them in the snapshot + */ + flush_fp_to_thread(current); + flush_altivec_to_thread(current); + flush_spe_to_thread(current); + +#ifdef CONFIG_PPC64 + hard_irq_disable(); +#endif + +} + +void restore_processor_state(void) +{ +#ifdef CONFIG_PPC32 + set_context(current->active_mm->context.id, current->active_mm->pgd); +#endif + +#ifdef CONFIG_PPC64 + hard_irq_enable(); +#endif +} diff --git a/arch/powerpc/kernel/swsusp_64.c b/arch/powerpc/kernel/swsusp_64.c new file mode 100644 index 00000000000..6f3f0697274 --- /dev/null +++ b/arch/powerpc/kernel/swsusp_64.c @@ -0,0 +1,24 @@ +/* + * PowerPC 64-bit swsusp implementation + * + * Copyright 2006 Johannes Berg <johannes@sipsolutions.net> + * + * GPLv2 + */ + +#include <asm/system.h> +#include <asm/iommu.h> +#include <linux/irq.h> +#include <linux/interrupt.h> + +void do_after_copyback(void) +{ + iommu_restore(); + touch_softlockup_watchdog(); + mb(); +} + +void _iommu_save(void) +{ + iommu_save(); +} diff --git a/arch/powerpc/kernel/swsusp_asm64.S b/arch/powerpc/kernel/swsusp_asm64.S new file mode 100644 index 00000000000..e092c3cbdb9 --- /dev/null +++ b/arch/powerpc/kernel/swsusp_asm64.S @@ -0,0 +1,228 @@ +/* + * PowerPC 64-bit swsusp implementation + * + * Copyright 2006 Johannes Berg <johannes@sipsolutions.net> + * + * GPLv2 + */ + +#include <linux/threads.h> +#include <asm/processor.h> +#include <asm/page.h> +#include <asm/cputable.h> +#include <asm/thread_info.h> +#include <asm/ppc_asm.h> +#include <asm/asm-offsets.h> + +/* + * Structure for storing CPU registers on the save area. + */ +#define SL_r1 0x00 /* stack pointer */ +#define SL_PC 0x08 +#define SL_MSR 0x10 +#define SL_SDR1 0x18 +#define SL_XER 0x20 +#define SL_TB 0x40 +#define SL_r2 0x48 +#define SL_CR 0x50 +#define SL_LR 0x58 +#define SL_r12 0x60 +#define SL_r13 0x68 +#define SL_r14 0x70 +#define SL_r15 0x78 +#define SL_r16 0x80 +#define SL_r17 0x88 +#define SL_r18 0x90 +#define SL_r19 0x98 +#define SL_r20 0xa0 +#define SL_r21 0xa8 +#define SL_r22 0xb0 +#define SL_r23 0xb8 +#define SL_r24 0xc0 +#define SL_r25 0xc8 +#define SL_r26 0xd0 +#define SL_r27 0xd8 +#define SL_r28 0xe0 +#define SL_r29 0xe8 +#define SL_r30 0xf0 +#define SL_r31 0xf8 +#define SL_SIZE SL_r31+8 + +/* these macros rely on the save area being + * pointed to by r11 */ +#define SAVE_SPECIAL(special) \ + mf##special r0 ;\ + std r0, SL_##special(r11) +#define RESTORE_SPECIAL(special) \ + ld r0, SL_##special(r11) ;\ + mt##special r0 +#define SAVE_REGISTER(reg) \ + std reg, SL_##reg(r11) +#define RESTORE_REGISTER(reg) \ + ld reg, SL_##reg(r11) + +/* space for storing cpu state */ + .section .data + .align 5 +swsusp_save_area: + .space SL_SIZE + + .section ".toc","aw" +swsusp_save_area_ptr: + .tc swsusp_save_area[TC],swsusp_save_area +restore_pblist_ptr: + .tc restore_pblist[TC],restore_pblist + + .section .text + .align 5 +_GLOBAL(swsusp_arch_suspend) + ld r11,swsusp_save_area_ptr@toc(r2) + SAVE_SPECIAL(LR) + SAVE_REGISTER(r1) + SAVE_SPECIAL(CR) + SAVE_SPECIAL(TB) + SAVE_REGISTER(r2) + SAVE_REGISTER(r12) + SAVE_REGISTER(r13) + SAVE_REGISTER(r14) + SAVE_REGISTER(r15) + SAVE_REGISTER(r16) + SAVE_REGISTER(r17) + SAVE_REGISTER(r18) + SAVE_REGISTER(r19) + SAVE_REGISTER(r20) + SAVE_REGISTER(r21) + SAVE_REGISTER(r22) + SAVE_REGISTER(r23) + SAVE_REGISTER(r24) + SAVE_REGISTER(r25) + SAVE_REGISTER(r26) + SAVE_REGISTER(r27) + SAVE_REGISTER(r28) + SAVE_REGISTER(r29) + SAVE_REGISTER(r30) + SAVE_REGISTER(r31) + SAVE_SPECIAL(MSR) + SAVE_SPECIAL(SDR1) + SAVE_SPECIAL(XER) + + /* we push the stack up 128 bytes but don't store the + * stack pointer on the stack like a real stackframe */ + addi r1,r1,-128 + + bl _iommu_save + bl swsusp_save + + /* restore LR */ + ld r11,swsusp_save_area_ptr@toc(r2) + RESTORE_SPECIAL(LR) + addi r1,r1,128 + + blr + +/* Resume code */ +_GLOBAL(swsusp_arch_resume) + /* Stop pending alitvec streams and memory accesses */ +BEGIN_FTR_SECTION + DSSALL +END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC) + sync + + ld r12,restore_pblist_ptr@toc(r2) + ld r12,0(r12) + + cmpdi r12,0 + beq- nothing_to_copy + li r15,512 +copyloop: + ld r13,pbe_address(r12) + ld r14,pbe_orig_address(r12) + + mtctr r15 + li r10,0 +copy_page_loop: + ldx r0,r10,r13 + stdx r0,r10,r14 + addi r10,r10,8 + bdnz copy_page_loop + + ld r12,pbe_next(r12) + cmpdi r12,0 + bne+ copyloop +nothing_to_copy: + + /* flush caches */ + lis r3, 0x10 + mtctr r3 + li r3, 0 + ori r3, r3, CONFIG_KERNEL_START>>48 + li r0, 48 + sld r3, r3, r0 + li r0, 0 +1: + dcbf r0,r3 + addi r3,r3,0x20 + bdnz 1b + + sync + + tlbia + + ld r11,swsusp_save_area_ptr@toc(r2) + + RESTORE_SPECIAL(CR) + + /* restore timebase */ + /* load saved tb */ + ld r1, SL_TB(r11) + /* get upper 32 bits of it */ + srdi r2, r1, 32 + /* clear tb lower to avoid wrap */ + li r0, 0 + mttbl r0 + /* set tb upper */ + mttbu r2 + /* set tb lower */ + mttbl r1 + + /* restore registers */ + RESTORE_REGISTER(r1) + RESTORE_REGISTER(r2) + RESTORE_REGISTER(r12) + RESTORE_REGISTER(r13) + RESTORE_REGISTER(r14) + RESTORE_REGISTER(r15) + RESTORE_REGISTER(r16) + RESTORE_REGISTER(r17) + RESTORE_REGISTER(r18) + RESTORE_REGISTER(r19) + RESTORE_REGISTER(r20) + RESTORE_REGISTER(r21) + RESTORE_REGISTER(r22) + RESTORE_REGISTER(r23) + RESTORE_REGISTER(r24) + RESTORE_REGISTER(r25) + RESTORE_REGISTER(r26) + RESTORE_REGISTER(r27) + RESTORE_REGISTER(r28) + RESTORE_REGISTER(r29) + RESTORE_REGISTER(r30) + RESTORE_REGISTER(r31) + /* can't use RESTORE_SPECIAL(MSR) */ + ld r0, SL_MSR(r11) + mtmsrd r0, 0 + RESTORE_SPECIAL(SDR1) + RESTORE_SPECIAL(XER) + + sync + + addi r1,r1,-128 + bl slb_flush_and_rebolt + bl do_after_copyback + addi r1,r1,128 + + ld r11,swsusp_save_area_ptr@toc(r2) + RESTORE_SPECIAL(LR) + + li r3, 0 + blr diff --git a/arch/powerpc/kernel/sysfs.c b/arch/powerpc/kernel/sysfs.c index 933e214c33e..cae39d9dfe4 100644 --- a/arch/powerpc/kernel/sysfs.c +++ b/arch/powerpc/kernel/sysfs.c @@ -499,4 +499,4 @@ static int __init topology_init(void) return 0; } -__initcall(topology_init); +subsys_initcall(topology_init); diff --git a/arch/powerpc/kernel/vio.c b/arch/powerpc/kernel/vio.c index b2c1b67a10a..62c1bc12ea3 100644 --- a/arch/powerpc/kernel/vio.c +++ b/arch/powerpc/kernel/vio.c @@ -117,7 +117,7 @@ static const struct vio_device_id *vio_match_device( { while (ids->type[0] != '\0') { if ((strncmp(dev->type, ids->type, strlen(ids->type)) == 0) && - device_is_compatible(dev->dev.archdata.of_node, + of_device_is_compatible(dev->dev.archdata.of_node, ids->compat)) return ids; ids++; diff --git a/arch/powerpc/mm/44x_mmu.c b/arch/powerpc/mm/44x_mmu.c index 0a0a0487b33..ca4dcb07a93 100644 --- a/arch/powerpc/mm/44x_mmu.c +++ b/arch/powerpc/mm/44x_mmu.c @@ -24,73 +24,38 @@ * */ -#include <linux/signal.h> -#include <linux/sched.h> -#include <linux/kernel.h> -#include <linux/errno.h> -#include <linux/string.h> -#include <linux/types.h> -#include <linux/ptrace.h> -#include <linux/mman.h> -#include <linux/mm.h> -#include <linux/swap.h> -#include <linux/stddef.h> -#include <linux/vmalloc.h> #include <linux/init.h> -#include <linux/delay.h> -#include <linux/highmem.h> - -#include <asm/pgalloc.h> -#include <asm/prom.h> -#include <asm/io.h> -#include <asm/mmu_context.h> -#include <asm/pgtable.h> #include <asm/mmu.h> -#include <asm/uaccess.h> -#include <asm/smp.h> -#include <asm/bootx.h> -#include <asm/machdep.h> -#include <asm/setup.h> +#include <asm/system.h> +#include <asm/page.h> #include "mmu_decl.h" -extern char etext[], _stext[]; - /* Used by the 44x TLB replacement exception handler. * Just needed it declared someplace. */ -unsigned int tlb_44x_index = 0; -unsigned int tlb_44x_hwater = 62; +unsigned int tlb_44x_index; /* = 0 */ +unsigned int tlb_44x_hwater = PPC44x_TLB_SIZE - 1 - PPC44x_EARLY_TLBS; /* * "Pins" a 256MB TLB entry in AS0 for kernel lowmem */ -static void __init -ppc44x_pin_tlb(int slot, unsigned int virt, unsigned int phys) +static void __init ppc44x_pin_tlb(unsigned int virt, unsigned int phys) { - unsigned long attrib = 0; - - __asm__ __volatile__("\ - clrrwi %2,%2,10\n\ - ori %2,%2,%4\n\ - clrrwi %1,%1,10\n\ - li %0,0\n\ - ori %0,%0,%5\n\ - tlbwe %2,%3,%6\n\ - tlbwe %1,%3,%7\n\ - tlbwe %0,%3,%8" + __asm__ __volatile__( + "tlbwe %2,%3,%4\n" + "tlbwe %1,%3,%5\n" + "tlbwe %0,%3,%6\n" : - : "r" (attrib), "r" (phys), "r" (virt), "r" (slot), - "i" (PPC44x_TLB_VALID | PPC44x_TLB_256M), - "i" (PPC44x_TLB_SW | PPC44x_TLB_SR | PPC44x_TLB_SX | PPC44x_TLB_G), + : "r" (PPC44x_TLB_SW | PPC44x_TLB_SR | PPC44x_TLB_SX | PPC44x_TLB_G), + "r" (phys), + "r" (virt | PPC44x_TLB_VALID | PPC44x_TLB_256M), + "r" (tlb_44x_hwater--), /* slot for this TLB entry */ "i" (PPC44x_TLB_PAGEID), "i" (PPC44x_TLB_XLAT), "i" (PPC44x_TLB_ATTRIB)); } -/* - * MMU_init_hw does the chip-specific initialization of the MMU hardware. - */ void __init MMU_init_hw(void) { flush_instruction_cache(); @@ -98,22 +63,13 @@ void __init MMU_init_hw(void) unsigned long __init mmu_mapin_ram(void) { - unsigned int pinned_tlbs = 1; - int i; - - /* Determine number of entries necessary to cover lowmem */ - pinned_tlbs = (unsigned int) - (_ALIGN(total_lowmem, PPC_PIN_SIZE) >> PPC44x_PIN_SHIFT); - - /* Write upper watermark to save location */ - tlb_44x_hwater = PPC44x_LOW_SLOT - pinned_tlbs; + unsigned long addr; - /* If necessary, set additional pinned TLBs */ - if (pinned_tlbs > 1) - for (i = (PPC44x_LOW_SLOT-(pinned_tlbs-1)); i < PPC44x_LOW_SLOT; i++) { - unsigned int phys_addr = (PPC44x_LOW_SLOT-i) * PPC_PIN_SIZE; - ppc44x_pin_tlb(i, phys_addr+PAGE_OFFSET, phys_addr); - } + /* Pin in enough TLBs to cover any lowmem not covered by the + * initial 256M mapping established in head_44x.S */ + for (addr = PPC_PIN_SIZE; addr < total_lowmem; + addr += PPC_PIN_SIZE) + ppc44x_pin_tlb(addr + PAGE_OFFSET, addr); return total_lowmem; } diff --git a/arch/powerpc/mm/fault.c b/arch/powerpc/mm/fault.c index 03aeb3a4607..a0f88026e46 100644 --- a/arch/powerpc/mm/fault.c +++ b/arch/powerpc/mm/fault.c @@ -39,37 +39,26 @@ #include <asm/kdebug.h> #include <asm/siginfo.h> -#ifdef CONFIG_KPROBES -ATOMIC_NOTIFIER_HEAD(notify_page_fault_chain); -/* Hook to register for page fault notifications */ -int register_page_fault_notifier(struct notifier_block *nb) -{ - return atomic_notifier_chain_register(¬ify_page_fault_chain, nb); -} - -int unregister_page_fault_notifier(struct notifier_block *nb) +#ifdef CONFIG_KPROBES +static inline int notify_page_fault(struct pt_regs *regs) { - return atomic_notifier_chain_unregister(¬ify_page_fault_chain, nb); -} + int ret = 0; + + /* kprobe_running() needs smp_processor_id() */ + if (!user_mode(regs)) { + preempt_disable(); + if (kprobe_running() && kprobe_fault_handler(regs, 11)) + ret = 1; + preempt_enable(); + } -static inline int notify_page_fault(enum die_val val, const char *str, - struct pt_regs *regs, long err, int trap, int sig) -{ - struct die_args args = { - .regs = regs, - .str = str, - .err = err, - .trapnr = trap, - .signr = sig - }; - return atomic_notifier_call_chain(¬ify_page_fault_chain, val, &args); + return ret; } #else -static inline int notify_page_fault(enum die_val val, const char *str, - struct pt_regs *regs, long err, int trap, int sig) +static inline int notify_page_fault(struct pt_regs *regs) { - return NOTIFY_DONE; + return 0; } #endif @@ -175,8 +164,7 @@ int __kprobes do_page_fault(struct pt_regs *regs, unsigned long address, is_write = error_code & ESR_DST; #endif /* CONFIG_4xx || CONFIG_BOOKE */ - if (notify_page_fault(DIE_PAGE_FAULT, "page_fault", regs, error_code, - 11, SIGSEGV) == NOTIFY_STOP) + if (notify_page_fault(regs)) return 0; if (trap == 0x300) { diff --git a/arch/powerpc/mm/hash_native_64.c b/arch/powerpc/mm/hash_native_64.c index 79aedaf36f2..7b7fe2d7b9d 100644 --- a/arch/powerpc/mm/hash_native_64.c +++ b/arch/powerpc/mm/hash_native_64.c @@ -26,6 +26,7 @@ #include <asm/tlb.h> #include <asm/cputable.h> #include <asm/udbg.h> +#include <asm/kexec.h> #ifdef DEBUG_LOW #define DBG_LOW(fmt...) udbg_printf(fmt) @@ -340,31 +341,70 @@ static void native_hpte_invalidate(unsigned long slot, unsigned long va, local_irq_restore(flags); } -/* - * XXX This need fixing based on page size. It's only used by - * native_hpte_clear() for now which needs fixing too so they - * make a good pair... - */ -static unsigned long slot2va(unsigned long hpte_v, unsigned long slot) -{ - unsigned long avpn = HPTE_V_AVPN_VAL(hpte_v); - unsigned long va; +#define LP_SHIFT 12 +#define LP_BITS 8 +#define LP_MASK(i) ((0xFF >> (i)) << LP_SHIFT) - va = avpn << 23; +static void hpte_decode(hpte_t *hpte, unsigned long slot, + int *psize, unsigned long *va) +{ + unsigned long hpte_r = hpte->r; + unsigned long hpte_v = hpte->v; + unsigned long avpn; + int i, size, shift, penc, avpnm_bits; + + if (!(hpte_v & HPTE_V_LARGE)) + size = MMU_PAGE_4K; + else { + for (i = 0; i < LP_BITS; i++) { + if ((hpte_r & LP_MASK(i+1)) == LP_MASK(i+1)) + break; + } + penc = LP_MASK(i+1) >> LP_SHIFT; + for (size = 0; size < MMU_PAGE_COUNT; size++) { - if (! (hpte_v & HPTE_V_LARGE)) { - unsigned long vpi, pteg; + /* 4K pages are not represented by LP */ + if (size == MMU_PAGE_4K) + continue; - pteg = slot / HPTES_PER_GROUP; - if (hpte_v & HPTE_V_SECONDARY) - pteg = ~pteg; + /* valid entries have a shift value */ + if (!mmu_psize_defs[size].shift) + continue; - vpi = ((va >> 28) ^ pteg) & htab_hash_mask; + if (penc == mmu_psize_defs[size].penc) + break; + } + } - va |= vpi << PAGE_SHIFT; + /* + * FIXME, the code below works for 16M, 64K, and 4K pages as these + * fall under the p<=23 rules for calculating the virtual address. + * In the case of 16M pages, an extra bit is stolen from the AVPN + * field to achieve the requisite 24 bits. + * + * Does not work for 16G pages or 1 TB segments. + */ + shift = mmu_psize_defs[size].shift; + if (mmu_psize_defs[size].avpnm) + avpnm_bits = __ilog2_u64(mmu_psize_defs[size].avpnm) + 1; + else + avpnm_bits = 0; + if (shift - avpnm_bits <= 23) { + avpn = HPTE_V_AVPN_VAL(hpte_v) << 23; + + if (shift < 23) { + unsigned long vpi, pteg; + + pteg = slot / HPTES_PER_GROUP; + if (hpte_v & HPTE_V_SECONDARY) + pteg = ~pteg; + vpi = ((avpn >> 28) ^ pteg) & htab_hash_mask; + avpn |= (vpi << mmu_psize_defs[size].shift); + } } - return va; + *va = avpn; + *psize = size; } /* @@ -374,15 +414,14 @@ static unsigned long slot2va(unsigned long hpte_v, unsigned long slot) * * TODO: add batching support when enabled. remember, no dynamic memory here, * athough there is the control page available... - * - * XXX FIXME: 4k only for now ! */ static void native_hpte_clear(void) { unsigned long slot, slots, flags; hpte_t *hptep = htab_address; - unsigned long hpte_v; + unsigned long hpte_v, va; unsigned long pteg_count; + int psize; pteg_count = htab_hash_mask + 1; @@ -408,8 +447,9 @@ static void native_hpte_clear(void) * already hold the native_tlbie_lock. */ if (hpte_v & HPTE_V_VALID) { + hpte_decode(hptep, slot, &psize, &va); hptep->v = 0; - __tlbie(slot2va(hpte_v, slot), MMU_PAGE_4K); + __tlbie(va, psize); } } diff --git a/arch/powerpc/mm/hash_utils_64.c b/arch/powerpc/mm/hash_utils_64.c index 49618461def..9b226fa7006 100644 --- a/arch/powerpc/mm/hash_utils_64.c +++ b/arch/powerpc/mm/hash_utils_64.c @@ -103,7 +103,7 @@ int mmu_ci_restrictions; #ifdef CONFIG_DEBUG_PAGEALLOC static u8 *linear_map_hash_slots; static unsigned long linear_map_hash_count; -static spinlock_t linear_map_hash_lock; +static DEFINE_SPINLOCK(linear_map_hash_lock); #endif /* CONFIG_DEBUG_PAGEALLOC */ /* There are definitions of page sizes arrays to be used when none diff --git a/arch/powerpc/mm/mem.c b/arch/powerpc/mm/mem.c index c4bcd754642..1a6e08f3298 100644 --- a/arch/powerpc/mm/mem.c +++ b/arch/powerpc/mm/mem.c @@ -80,7 +80,6 @@ int page_is_ram(unsigned long pfn) return 0; #endif } -EXPORT_SYMBOL(page_is_ram); pgprot_t phys_mem_access_prot(struct file *file, unsigned long pfn, unsigned long size, pgprot_t vma_prot) diff --git a/arch/powerpc/mm/mmu_decl.h b/arch/powerpc/mm/mmu_decl.h index 9c4538bb04b..2558c34eeda 100644 --- a/arch/powerpc/mm/mmu_decl.h +++ b/arch/powerpc/mm/mmu_decl.h @@ -40,7 +40,8 @@ extern int __map_without_bats; extern unsigned long ioremap_base; extern unsigned int rtas_data, rtas_size; -extern PTE *Hash, *Hash_end; +struct _PTE; +extern struct _PTE *Hash, *Hash_end; extern unsigned long Hash_size, Hash_mask; extern unsigned int num_tlbcam_entries; diff --git a/arch/powerpc/mm/stab.c b/arch/powerpc/mm/stab.c index eeeacab548e..132c6bc66ce 100644 --- a/arch/powerpc/mm/stab.c +++ b/arch/powerpc/mm/stab.c @@ -227,7 +227,7 @@ void switch_stab(struct task_struct *tsk, struct mm_struct *mm) * the first (bolted) segment, so that do_stab_bolted won't get a * recursive segment miss on the segment table itself. */ -void stabs_alloc(void) +void __init stabs_alloc(void) { int cpu; diff --git a/arch/powerpc/platforms/52xx/Kconfig b/arch/powerpc/platforms/52xx/Kconfig index bc4aa4a80a1..3ffaa066c2c 100644 --- a/arch/powerpc/platforms/52xx/Kconfig +++ b/arch/powerpc/platforms/52xx/Kconfig @@ -1,5 +1,6 @@ config PPC_MPC52xx bool + select FSL_SOC default n config PPC_MPC5200 diff --git a/arch/powerpc/platforms/52xx/Makefile b/arch/powerpc/platforms/52xx/Makefile index 07cdbcacf15..b91e39c84d4 100644 --- a/arch/powerpc/platforms/52xx/Makefile +++ b/arch/powerpc/platforms/52xx/Makefile @@ -8,3 +8,5 @@ endif obj-$(CONFIG_PPC_EFIKA) += efika.o obj-$(CONFIG_PPC_LITE5200) += lite5200.o + +obj-$(CONFIG_PM) += mpc52xx_sleep.o mpc52xx_pm.o diff --git a/arch/powerpc/platforms/52xx/efika.c b/arch/powerpc/platforms/52xx/efika.c index a6bba97314e..f591a9fc19b 100644 --- a/arch/powerpc/platforms/52xx/efika.c +++ b/arch/powerpc/platforms/52xx/efika.c @@ -184,6 +184,16 @@ static void efika_show_cpuinfo(struct seq_file *m) of_node_put(root); } +#ifdef CONFIG_PM +static void efika_suspend_prepare(void __iomem *mbar) +{ + u8 pin = 4; /* GPIO_WKUP_4 (GPIO_PSC6_0 - IRDA_RX) */ + u8 level = 1; /* wakeup on high level */ + /* IOW. to wake it up, short pins 1 and 3 on IRDA connector */ + mpc52xx_set_wakeup_gpio(pin, level); +} +#endif + static void __init efika_setup_arch(void) { rtas_initialize(); @@ -199,6 +209,11 @@ static void __init efika_setup_arch(void) efika_pcisetup(); +#ifdef CONFIG_PM + mpc52xx_suspend.board_suspend_prepare = efika_suspend_prepare; + mpc52xx_pm_init(); +#endif + if (ppc_md.progress) ppc_md.progress("Linux/PPC " UTS_RELEASE " running on Efika ;-)\n", 0x0); } diff --git a/arch/powerpc/platforms/52xx/lite5200.c b/arch/powerpc/platforms/52xx/lite5200.c index 8e2646ac417..1cfc00dfb99 100644 --- a/arch/powerpc/platforms/52xx/lite5200.c +++ b/arch/powerpc/platforms/52xx/lite5200.c @@ -85,6 +85,28 @@ error: iounmap(gpio); } +#ifdef CONFIG_PM +static u32 descr_a; +static void lite5200_suspend_prepare(void __iomem *mbar) +{ + u8 pin = 1; /* GPIO_WKUP_1 (GPIO_PSC2_4) */ + u8 level = 0; /* wakeup on low level */ + mpc52xx_set_wakeup_gpio(pin, level); + + /* + * power down usb port + * this needs to be called before of-ohci suspend code + */ + descr_a = in_be32(mbar + 0x1048); + out_be32(mbar + 0x1048, (descr_a & ~0x200) | 0x100); +} + +static void lite5200_resume_finish(void __iomem *mbar) +{ + out_be32(mbar + 0x1048, descr_a); +} +#endif + static void __init lite5200_setup_arch(void) { struct device_node *np; @@ -107,6 +129,12 @@ static void __init lite5200_setup_arch(void) mpc52xx_setup_cpu(); /* Generic */ lite5200_setup_cpu(); /* Platorm specific */ +#ifdef CONFIG_PM + mpc52xx_suspend.board_suspend_prepare = lite5200_suspend_prepare; + mpc52xx_suspend.board_resume_finish = lite5200_resume_finish; + mpc52xx_pm_init(); +#endif + #ifdef CONFIG_PCI np = of_find_node_by_type(NULL, "pci"); if (np) { diff --git a/arch/powerpc/platforms/52xx/mpc52xx_pm.c b/arch/powerpc/platforms/52xx/mpc52xx_pm.c new file mode 100644 index 00000000000..fd40044d16c --- /dev/null +++ b/arch/powerpc/platforms/52xx/mpc52xx_pm.c @@ -0,0 +1,191 @@ +#include <linux/init.h> +#include <linux/pm.h> +#include <linux/io.h> +#include <asm/time.h> +#include <asm/cacheflush.h> +#include <asm/mpc52xx.h> + +#include "mpc52xx_pic.h" + + +/* these are defined in mpc52xx_sleep.S, and only used here */ +extern void mpc52xx_deep_sleep(void *sram, void *sdram_regs, + struct mpc52xx_cdm *, struct mpc52xx_intr *); +extern void mpc52xx_ds_sram(void); +extern const long mpc52xx_ds_sram_size; +extern void mpc52xx_ds_cached(void); +extern const long mpc52xx_ds_cached_size; + +static void __iomem *mbar; +static void __iomem *sdram; +static struct mpc52xx_cdm __iomem *cdm; +static struct mpc52xx_intr __iomem *intr; +static struct mpc52xx_gpio_wkup __iomem *gpiow; +static void *sram; +static int sram_size; + +struct mpc52xx_suspend mpc52xx_suspend; + +static int mpc52xx_pm_valid(suspend_state_t state) +{ + switch (state) { + case PM_SUSPEND_STANDBY: + return 1; + default: + return 0; + } +} + +int mpc52xx_set_wakeup_gpio(u8 pin, u8 level) +{ + u16 tmp; + + /* enable gpio */ + out_8(&gpiow->wkup_gpioe, in_8(&gpiow->wkup_gpioe) | (1 << pin)); + /* set as input */ + out_8(&gpiow->wkup_ddr, in_8(&gpiow->wkup_ddr) & ~(1 << pin)); + /* enable deep sleep interrupt */ + out_8(&gpiow->wkup_inten, in_8(&gpiow->wkup_inten) | (1 << pin)); + /* low/high level creates wakeup interrupt */ + tmp = in_be16(&gpiow->wkup_itype); + tmp &= ~(0x3 << (pin * 2)); + tmp |= (!level + 1) << (pin * 2); + out_be16(&gpiow->wkup_itype, tmp); + /* master enable */ + out_8(&gpiow->wkup_maste, 1); + + return 0; +} + +int mpc52xx_pm_prepare(suspend_state_t state) +{ + if (state != PM_SUSPEND_STANDBY) + return -EINVAL; + + /* map the whole register space */ + mbar = mpc52xx_find_and_map("mpc5200"); + if (!mbar) { + printk(KERN_ERR "%s:%i Error mapping registers\n", __func__, __LINE__); + return -ENOSYS; + } + /* these offsets are from mpc5200 users manual */ + sdram = mbar + 0x100; + cdm = mbar + 0x200; + intr = mbar + 0x500; + gpiow = mbar + 0xc00; + sram = mbar + 0x8000; /* Those will be handled by the */ + sram_size = 0x4000; /* bestcomm driver soon */ + + /* call board suspend code, if applicable */ + if (mpc52xx_suspend.board_suspend_prepare) + mpc52xx_suspend.board_suspend_prepare(mbar); + else { + printk(KERN_ALERT "%s: %i don't know how to wake up the board\n", + __func__, __LINE__); + goto out_unmap; + } + + return 0; + + out_unmap: + iounmap(mbar); + return -ENOSYS; +} + + +char saved_sram[0x4000]; + +int mpc52xx_pm_enter(suspend_state_t state) +{ + u32 clk_enables; + u32 msr, hid0; + u32 intr_main_mask; + void __iomem * irq_0x500 = (void *)CONFIG_KERNEL_START + 0x500; + unsigned long irq_0x500_stop = (unsigned long)irq_0x500 + mpc52xx_ds_cached_size; + char saved_0x500[mpc52xx_ds_cached_size]; + + /* disable all interrupts in PIC */ + intr_main_mask = in_be32(&intr->main_mask); + out_be32(&intr->main_mask, intr_main_mask | 0x1ffff); + + /* don't let DEC expire any time soon */ + mtspr(SPRN_DEC, 0x7fffffff); + + /* save SRAM */ + memcpy(saved_sram, sram, sram_size); + + /* copy low level suspend code to sram */ + memcpy(sram, mpc52xx_ds_sram, mpc52xx_ds_sram_size); + + out_8(&cdm->ccs_sleep_enable, 1); + out_8(&cdm->osc_sleep_enable, 1); + out_8(&cdm->ccs_qreq_test, 1); + + /* disable all but SDRAM and bestcomm (SRAM) clocks */ + clk_enables = in_be32(&cdm->clk_enables); + out_be32(&cdm->clk_enables, clk_enables & 0x00088000); + + /* disable power management */ + msr = mfmsr(); + mtmsr(msr & ~MSR_POW); + + /* enable sleep mode, disable others */ + hid0 = mfspr(SPRN_HID0); + mtspr(SPRN_HID0, (hid0 & ~(HID0_DOZE | HID0_NAP | HID0_DPM)) | HID0_SLEEP); + + /* save original, copy our irq handler, flush from dcache and invalidate icache */ + memcpy(saved_0x500, irq_0x500, mpc52xx_ds_cached_size); + memcpy(irq_0x500, mpc52xx_ds_cached, mpc52xx_ds_cached_size); + flush_icache_range((unsigned long)irq_0x500, irq_0x500_stop); + + /* call low-level sleep code */ + mpc52xx_deep_sleep(sram, sdram, cdm, intr); + + /* restore original irq handler */ + memcpy(irq_0x500, saved_0x500, mpc52xx_ds_cached_size); + flush_icache_range((unsigned long)irq_0x500, irq_0x500_stop); + + /* restore old power mode */ + mtmsr(msr & ~MSR_POW); + mtspr(SPRN_HID0, hid0); + mtmsr(msr); + + out_be32(&cdm->clk_enables, clk_enables); + out_8(&cdm->ccs_sleep_enable, 0); + out_8(&cdm->osc_sleep_enable, 0); + + /* restore SRAM */ + memcpy(sram, saved_sram, sram_size); + + /* restart jiffies */ + wakeup_decrementer(); + + /* reenable interrupts in PIC */ + out_be32(&intr->main_mask, intr_main_mask); + + return 0; +} + +int mpc52xx_pm_finish(suspend_state_t state) +{ + /* call board resume code */ + if (mpc52xx_suspend.board_resume_finish) + mpc52xx_suspend.board_resume_finish(mbar); + + iounmap(mbar); + + return 0; +} + +static struct pm_ops mpc52xx_pm_ops = { + .valid = mpc52xx_pm_valid, + .prepare = mpc52xx_pm_prepare, + .enter = mpc52xx_pm_enter, + .finish = mpc52xx_pm_finish, +}; + +int __init mpc52xx_pm_init(void) +{ + pm_set_ops(&mpc52xx_pm_ops); + return 0; +} diff --git a/arch/powerpc/platforms/52xx/mpc52xx_sleep.S b/arch/powerpc/platforms/52xx/mpc52xx_sleep.S new file mode 100644 index 00000000000..4dc170b0ae1 --- /dev/null +++ b/arch/powerpc/platforms/52xx/mpc52xx_sleep.S @@ -0,0 +1,154 @@ +#include <asm/reg.h> +#include <asm/ppc_asm.h> +#include <asm/processor.h> + + +.text + +_GLOBAL(mpc52xx_deep_sleep) +mpc52xx_deep_sleep: /* args r3-r6: SRAM, SDRAM regs, CDM regs, INTR regs */ + + /* enable interrupts */ + mfmsr r7 + ori r7, r7, 0x8000 /* EE */ + mtmsr r7 + sync; isync; + + li r10, 0 /* flag that irq handler sets */ + + /* enable tmr7 (or any other) interrupt */ + lwz r8, 0x14(r6) /* intr->main_mask */ + ori r8, r8, 0x1 + xori r8, r8, 0x1 + stw r8, 0x14(r6) + sync + + /* emulate tmr7 interrupt */ + li r8, 0x1 + stw r8, 0x40(r6) /* intr->main_emulate */ + sync + + /* wait for it to happen */ +1: + cmpi cr0, r10, 1 + bne cr0, 1b + + /* lock icache */ + mfspr r10, SPRN_HID0 + ori r10, r10, 0x2000 + sync; isync; + mtspr SPRN_HID0, r10 + sync; isync; + + + mflr r9 /* save LR */ + + /* jump to sram */ + mtlr r3 + blrl + + mtlr r9 /* restore LR */ + + /* unlock icache */ + mfspr r10, SPRN_HID0 + ori r10, r10, 0x2000 + xori r10, r10, 0x2000 + sync; isync; + mtspr SPRN_HID0, r10 + sync; isync; + + + /* return to C code */ + blr + + +_GLOBAL(mpc52xx_ds_sram) +mpc52xx_ds_sram: + /* put SDRAM into self-refresh */ + lwz r8, 0x4(r4) /* sdram->ctrl */ + + oris r8, r8, 0x8000 /* mode_en */ + stw r8, 0x4(r4) + sync + + ori r8, r8, 0x0002 /* soft_pre */ + stw r8, 0x4(r4) + sync + xori r8, r8, 0x0002 + + xoris r8, r8, 0x8000 /* !mode_en */ + stw r8, 0x4(r4) + sync + + oris r8, r8, 0x5000 + xoris r8, r8, 0x4000 /* ref_en !cke */ + stw r8, 0x4(r4) + sync + + /* disable SDRAM clock */ + lwz r8, 0x14(r5) /* cdm->clkenable */ + ori r8, r8, 0x0008 + xori r8, r8, 0x0008 + stw r8, 0x14(r5) + sync + + + /* put mpc5200 to sleep */ + mfmsr r10 + oris r10, r10, 0x0004 /* POW = 1 */ + sync; isync; + mtmsr r10 + sync; isync; + + + /* enable clock */ + lwz r8, 0x14(r5) + ori r8, r8, 0x0008 + stw r8, 0x14(r5) + sync + + /* get ram out of self-refresh */ + lwz r8, 0x4(r4) + oris r8, r8, 0x5000 /* cke ref_en */ + stw r8, 0x4(r4) + sync + + blr +_GLOBAL(mpc52xx_ds_sram_size) +mpc52xx_ds_sram_size: + .long $-mpc52xx_ds_sram + + +/* ### interrupt handler for wakeup from deep-sleep ### */ +_GLOBAL(mpc52xx_ds_cached) +mpc52xx_ds_cached: + mtspr SPRN_SPRG0, r7 + mtspr SPRN_SPRG1, r8 + + /* disable emulated interrupt */ + mfspr r7, 311 /* MBAR */ + addi r7, r7, 0x540 /* intr->main_emul */ + li r8, 0 + stw r8, 0(r7) + sync + dcbf 0, r7 + + /* acknowledge wakeup, so CCS releases power pown */ + mfspr r7, 311 /* MBAR */ + addi r7, r7, 0x524 /* intr->enc_status */ + lwz r8, 0(r7) + ori r8, r8, 0x0400 + stw r8, 0(r7) + sync + dcbf 0, r7 + + /* flag - we handled the interrupt */ + li r10, 1 + + mfspr r8, SPRN_SPRG1 + mfspr r7, SPRN_SPRG0 + + rfi +_GLOBAL(mpc52xx_ds_cached_size) +mpc52xx_ds_cached_size: + .long $-mpc52xx_ds_cached diff --git a/arch/powerpc/platforms/83xx/mpc832x_mds.c b/arch/powerpc/platforms/83xx/mpc832x_mds.c index fff09f5d6ed..94843ed52a9 100644 --- a/arch/powerpc/platforms/83xx/mpc832x_mds.c +++ b/arch/powerpc/platforms/83xx/mpc832x_mds.c @@ -111,6 +111,7 @@ static struct of_device_id mpc832x_ids[] = { { .type = "soc", }, { .compatible = "soc", }, { .type = "qe", }, + { .type = "mdio", }, {}, }; diff --git a/arch/powerpc/platforms/83xx/mpc832x_rdb.c b/arch/powerpc/platforms/83xx/mpc832x_rdb.c index 6b71e9ffb11..b0b22bb29de 100644 --- a/arch/powerpc/platforms/83xx/mpc832x_rdb.c +++ b/arch/powerpc/platforms/83xx/mpc832x_rdb.c @@ -73,6 +73,7 @@ static struct of_device_id mpc832x_ids[] = { { .type = "soc", }, { .compatible = "soc", }, { .type = "qe", }, + { .type = "mdio", }, {}, }; diff --git a/arch/powerpc/platforms/83xx/mpc836x_mds.c b/arch/powerpc/platforms/83xx/mpc836x_mds.c index 526ed090a44..bceeff8bbfd 100644 --- a/arch/powerpc/platforms/83xx/mpc836x_mds.c +++ b/arch/powerpc/platforms/83xx/mpc836x_mds.c @@ -118,6 +118,7 @@ static struct of_device_id mpc836x_ids[] = { { .type = "soc", }, { .compatible = "soc", }, { .type = "qe", }, + { .type = "mdio", }, {}, }; diff --git a/arch/powerpc/platforms/85xx/mpc8544_ds.c b/arch/powerpc/platforms/85xx/mpc8544_ds.c index 2867f85e632..bec84ffe708 100644 --- a/arch/powerpc/platforms/85xx/mpc8544_ds.c +++ b/arch/powerpc/platforms/85xx/mpc8544_ds.c @@ -84,7 +84,7 @@ void __init mpc8544_ds_pic_init(void) #ifdef CONFIG_PPC_I8259 /* Initialize the i8259 controller */ for_each_node_by_type(np, "interrupt-controller") - if (device_is_compatible(np, "chrp,iic")) { + if (of_device_is_compatible(np, "chrp,iic")) { cascade_node = np; break; } diff --git a/arch/powerpc/platforms/85xx/mpc85xx_cds.c b/arch/powerpc/platforms/85xx/mpc85xx_cds.c index 7e71636f909..1490eb3ce0d 100644 --- a/arch/powerpc/platforms/85xx/mpc85xx_cds.c +++ b/arch/powerpc/platforms/85xx/mpc85xx_cds.c @@ -197,7 +197,7 @@ static void __init mpc85xx_cds_pic_init(void) #ifdef CONFIG_PPC_I8259 /* Initialize the i8259 controller */ for_each_node_by_type(np, "interrupt-controller") - if (device_is_compatible(np, "chrp,iic")) { + if (of_device_is_compatible(np, "chrp,iic")) { cascade_node = np; break; } diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c index 54db4168995..e3dddbfe66f 100644 --- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c +++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c @@ -147,6 +147,7 @@ static struct of_device_id mpc85xx_ids[] = { { .type = "soc", }, { .compatible = "soc", }, { .type = "qe", }, + { .type = "mdio", }, {}, }; diff --git a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c index 3d3d98f5bd4..90877565caa 100644 --- a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c +++ b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c @@ -102,7 +102,7 @@ mpc86xx_hpcn_init_irq(void) #ifdef CONFIG_PCI /* Initialize i8259 controller */ for_each_node_by_type(np, "interrupt-controller") - if (device_is_compatible(np, "chrp,iic")) { + if (of_device_is_compatible(np, "chrp,iic")) { cascade_node = np; break; } diff --git a/arch/powerpc/platforms/cell/interrupt.c b/arch/powerpc/platforms/cell/interrupt.c index 4fc4e92775d..47264e72202 100644 --- a/arch/powerpc/platforms/cell/interrupt.c +++ b/arch/powerpc/platforms/cell/interrupt.c @@ -227,7 +227,7 @@ void iic_request_IPIs(void) static int iic_host_match(struct irq_host *h, struct device_node *node) { - return device_is_compatible(node, + return of_device_is_compatible(node, "IBM,CBEA-Internal-Interrupt-Controller"); } @@ -256,7 +256,7 @@ static int iic_host_xlate(struct irq_host *h, struct device_node *ct, unsigned int node, ext, unit, class; const u32 *val; - if (!device_is_compatible(ct, + if (!of_device_is_compatible(ct, "IBM,CBEA-Internal-Interrupt-Controller")) return -ENODEV; if (intsize != 1) @@ -324,7 +324,7 @@ static int __init setup_iic(void) for (dn = NULL; (dn = of_find_node_by_name(dn,"interrupt-controller")) != NULL;) { - if (!device_is_compatible(dn, + if (!of_device_is_compatible(dn, "IBM,CBEA-Internal-Interrupt-Controller")) continue; np = of_get_property(dn, "ibm,interrupt-server-ranges", NULL); diff --git a/arch/powerpc/platforms/cell/setup.c b/arch/powerpc/platforms/cell/setup.c index 54b96183cb6..db6654272e1 100644 --- a/arch/powerpc/platforms/cell/setup.c +++ b/arch/powerpc/platforms/cell/setup.c @@ -112,7 +112,7 @@ static void __init mpic_init_IRQ(void) for (dn = NULL; (dn = of_find_node_by_name(dn, "interrupt-controller"));) { - if (!device_is_compatible(dn, "CBEA,platform-open-pic")) + if (!of_device_is_compatible(dn, "CBEA,platform-open-pic")) continue; /* The MPIC driver will get everything it needs from the diff --git a/arch/powerpc/platforms/cell/spider-pic.c b/arch/powerpc/platforms/cell/spider-pic.c index fb1f15797bb..05f4b3d3d75 100644 --- a/arch/powerpc/platforms/cell/spider-pic.c +++ b/arch/powerpc/platforms/cell/spider-pic.c @@ -358,12 +358,12 @@ void __init spider_init_IRQ(void) */ for (dn = NULL; (dn = of_find_node_by_name(dn, "interrupt-controller"));) { - if (device_is_compatible(dn, "CBEA,platform-spider-pic")) { + if (of_device_is_compatible(dn, "CBEA,platform-spider-pic")) { if (of_address_to_resource(dn, 0, &r)) { printk(KERN_WARNING "spider-pic: Failed\n"); continue; } - } else if (device_is_compatible(dn, "sti,platform-spider-pic") + } else if (of_device_is_compatible(dn, "sti,platform-spider-pic") && (chip < 2)) { static long hard_coded_pics[] = { 0x24000008000ul, 0x34000008000ul}; diff --git a/arch/powerpc/platforms/chrp/pci.c b/arch/powerpc/platforms/chrp/pci.c index 1469d6478f6..d32fedc991d 100644 --- a/arch/powerpc/platforms/chrp/pci.c +++ b/arch/powerpc/platforms/chrp/pci.c @@ -267,7 +267,7 @@ chrp_find_bridges(void) model = of_get_property(dev, "model", NULL); if (model == NULL) model = "<none>"; - if (device_is_compatible(dev, "IBM,python")) { + if (of_device_is_compatible(dev, "IBM,python")) { setup_python(hose, dev); } else if (is_mot || strncmp(model, "Motorola, Grackle", 17) == 0) { diff --git a/arch/powerpc/platforms/chrp/setup.c b/arch/powerpc/platforms/chrp/setup.c index 1870038a8e0..373de4c063d 100644 --- a/arch/powerpc/platforms/chrp/setup.c +++ b/arch/powerpc/platforms/chrp/setup.c @@ -448,7 +448,7 @@ static void __init chrp_find_8259(void) /* Look for cascade */ for_each_node_by_type(np, "interrupt-controller") - if (device_is_compatible(np, "chrp,iic")) { + if (of_device_is_compatible(np, "chrp,iic")) { pic = np; break; } diff --git a/arch/powerpc/platforms/embedded6xx/Kconfig b/arch/powerpc/platforms/embedded6xx/Kconfig index 9557908ef54..8f3c2a73e16 100644 --- a/arch/powerpc/platforms/embedded6xx/Kconfig +++ b/arch/powerpc/platforms/embedded6xx/Kconfig @@ -20,16 +20,24 @@ config MPC7448HPC2 select TSI108_BRIDGE select DEFAULT_UIMAGE select PPC_UDBG_16550 - select MPIC - select MPIC_WEIRD help Select MPC7448HPC2 if configuring for Freescale MPC7448HPC2 (Taiga) platform + +config PPC_HOLLY + bool "PPC750GX/CL with TSI10x bridge (Hickory/Holly)" + select TSI108_BRIDGE + select PPC_UDBG_16550 + help + Select PPC_HOLLY if configuring for an IBM 750GX/CL Eval + Board with TSI108/9 bridge (Hickory/Holly) endchoice config TSI108_BRIDGE bool - depends on MPC7448HPC2 + depends on MPC7448HPC2 || PPC_HOLLY + select MPIC + select MPIC_WEIRD default y config MPC10X_BRIDGE diff --git a/arch/powerpc/platforms/embedded6xx/Makefile b/arch/powerpc/platforms/embedded6xx/Makefile index d3d11a3cd65..b39fe4f470d 100644 --- a/arch/powerpc/platforms/embedded6xx/Makefile +++ b/arch/powerpc/platforms/embedded6xx/Makefile @@ -3,3 +3,4 @@ # obj-$(CONFIG_MPC7448HPC2) += mpc7448_hpc2.o obj-$(CONFIG_LINKSTATION) += linkstation.o ls_uart.o +obj-$(CONFIG_PPC_HOLLY) += holly.o diff --git a/arch/powerpc/platforms/embedded6xx/holly.c b/arch/powerpc/platforms/embedded6xx/holly.c new file mode 100644 index 00000000000..3a0b4a01401 --- /dev/null +++ b/arch/powerpc/platforms/embedded6xx/holly.c @@ -0,0 +1,317 @@ +/* + * Board setup routines for the IBM 750GX/CL platform w/ TSI10x bridge + * + * Copyright 2007 IBM Corporation + * + * Stephen Winiecki <stevewin@us.ibm.com> + * Josh Boyer <jwboyer@linux.vnet.ibm.com> + * + * Based on code from mpc7448_hpc2.c + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + */ + +#include <linux/stddef.h> +#include <linux/kernel.h> +#include <linux/pci.h> +#include <linux/kdev_t.h> +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/irq.h> +#include <linux/ide.h> +#include <linux/seq_file.h> +#include <linux/root_dev.h> +#include <linux/serial.h> +#include <linux/tty.h> +#include <linux/serial_core.h> + +#include <asm/system.h> +#include <asm/time.h> +#include <asm/machdep.h> +#include <asm/prom.h> +#include <asm/udbg.h> +#include <asm/tsi108.h> +#include <asm/pci-bridge.h> +#include <asm/reg.h> +#include <mm/mmu_decl.h> +#include <asm/tsi108_irq.h> +#include <asm/tsi108_pci.h> +#include <asm/mpic.h> +#include <asm/of_platform.h> + +#undef DEBUG + +#define HOLLY_PCI_CFG_PHYS 0x7c000000 + +int holly_exclude_device(u_char bus, u_char devfn) +{ + if (bus == 0 && PCI_SLOT(devfn) == 0) + return PCIBIOS_DEVICE_NOT_FOUND; + else + return PCIBIOS_SUCCESSFUL; +} + +static void holly_remap_bridge(void) +{ + u32 lut_val, lut_addr; + int i; + + printk(KERN_INFO "Remapping PCI bridge\n"); + + /* Re-init the PCI bridge and LUT registers to have mappings that don't + * rely on PIBS + */ + lut_addr = 0x900; + for (i = 0; i < 31; i++) { + tsi108_write_reg(TSI108_PB_OFFSET + lut_addr, 0x00000201); + lut_addr += 4; + tsi108_write_reg(TSI108_PB_OFFSET + lut_addr, 0x0); + lut_addr += 4; + } + + /* Reserve the last LUT entry for PCI I/O space */ + tsi108_write_reg(TSI108_PB_OFFSET + lut_addr, 0x00000241); + lut_addr += 4; + tsi108_write_reg(TSI108_PB_OFFSET + lut_addr, 0x0); + + /* Map PCI I/O space */ + tsi108_write_reg(TSI108_PCI_PFAB_IO_UPPER, 0x0); + tsi108_write_reg(TSI108_PCI_PFAB_IO, 0x1); + + /* Map PCI CFG space */ + tsi108_write_reg(TSI108_PCI_PFAB_BAR0_UPPER, 0x0); + tsi108_write_reg(TSI108_PCI_PFAB_BAR0, 0x7c000000 | 0x01); + + /* We don't need MEM32 and PRM remapping so disable them */ + tsi108_write_reg(TSI108_PCI_PFAB_MEM32, 0x0); + tsi108_write_reg(TSI108_PCI_PFAB_PFM3, 0x0); + tsi108_write_reg(TSI108_PCI_PFAB_PFM4, 0x0); + + /* Set P2O_BAR0 */ + tsi108_write_reg(TSI108_PCI_P2O_BAR0_UPPER, 0x0); + tsi108_write_reg(TSI108_PCI_P2O_BAR0, 0xc0000000); + + /* Init the PCI LUTs to do no remapping */ + lut_addr = 0x500; + lut_val = 0x00000002; + + for (i = 0; i < 32; i++) { + tsi108_write_reg(TSI108_PCI_OFFSET + lut_addr, lut_val); + lut_addr += 4; + tsi108_write_reg(TSI108_PCI_OFFSET + lut_addr, 0x40000000); + lut_addr += 4; + lut_val += 0x02000000; + } + tsi108_write_reg(TSI108_PCI_P2O_PAGE_SIZES, 0x00007900); + + /* Set 64-bit PCI bus address for system memory */ + tsi108_write_reg(TSI108_PCI_P2O_BAR2_UPPER, 0x0); + tsi108_write_reg(TSI108_PCI_P2O_BAR2, 0x0); +} + +static void __init holly_setup_arch(void) +{ + struct device_node *cpu; + struct device_node *np; + + if (ppc_md.progress) + ppc_md.progress("holly_setup_arch():set_bridge", 0); + + cpu = of_find_node_by_type(NULL, "cpu"); + if (cpu) { + const unsigned int *fp; + + fp = of_get_property(cpu, "clock-frequency", NULL); + if (fp) + loops_per_jiffy = *fp / HZ; + else + loops_per_jiffy = 50000000 / HZ; + of_node_put(cpu); + } + tsi108_csr_vir_base = get_vir_csrbase(); + + /* setup PCI host bridge */ + holly_remap_bridge(); + + np = of_find_node_by_type(NULL, "pci"); + if (np) + tsi108_setup_pci(np, HOLLY_PCI_CFG_PHYS, 1); + + ppc_md.pci_exclude_device = holly_exclude_device; + if (ppc_md.progress) + ppc_md.progress("tsi108: resources set", 0x100); + + printk(KERN_INFO "PPC750GX/CL Platform\n"); +} + +/* + * Interrupt setup and service. Interrrupts on the holly come + * from the four external INT pins, PCI interrupts are routed via + * PCI interrupt control registers, it generates internal IRQ23 + * + * Interrupt routing on the Holly Board: + * TSI108:PB_INT[0] -> CPU0:INT# + * TSI108:PB_INT[1] -> CPU0:MCP# + * TSI108:PB_INT[2] -> N/C + * TSI108:PB_INT[3] -> N/C + */ +static void __init holly_init_IRQ(void) +{ + struct mpic *mpic; + phys_addr_t mpic_paddr = 0; + struct device_node *tsi_pic; +#ifdef CONFIG_PCI + unsigned int cascade_pci_irq; + struct device_node *tsi_pci; + struct device_node *cascade_node = NULL; +#endif + + tsi_pic = of_find_node_by_type(NULL, "open-pic"); + if (tsi_pic) { + unsigned int size; + const void *prop = of_get_property(tsi_pic, "reg", &size); + mpic_paddr = of_translate_address(tsi_pic, prop); + } + + if (mpic_paddr == 0) { + printk(KERN_ERR "%s: No tsi108 PIC found !\n", __func__); + return; + } + + pr_debug("%s: tsi108 pic phys_addr = 0x%x\n", __func__, (u32) mpic_paddr); + + mpic = mpic_alloc(tsi_pic, mpic_paddr, + MPIC_PRIMARY | MPIC_BIG_ENDIAN | MPIC_WANTS_RESET | + MPIC_SPV_EOI | MPIC_NO_PTHROU_DIS | MPIC_REGSET_TSI108, + 24, + NR_IRQS-4, /* num_sources used */ + "Tsi108_PIC"); + + BUG_ON(mpic == NULL); + + mpic_assign_isu(mpic, 0, mpic_paddr + 0x100); + + mpic_init(mpic); + +#ifdef CONFIG_PCI + tsi_pci = of_find_node_by_type(NULL, "pci"); + if (tsi_pci == NULL) { + printk(KERN_ERR "%s: No tsi108 pci node found !\n", __func__); + return; + } + + cascade_node = of_find_node_by_type(NULL, "pic-router"); + if (cascade_node == NULL) { + printk(KERN_ERR "%s: No tsi108 pci cascade node found !\n", __func__); + return; + } + + cascade_pci_irq = irq_of_parse_and_map(tsi_pci, 0); + pr_debug("%s: tsi108 cascade_pci_irq = 0x%x\n", __func__, (u32) cascade_pci_irq); + tsi108_pci_int_init(cascade_node); + set_irq_data(cascade_pci_irq, mpic); + set_irq_chained_handler(cascade_pci_irq, tsi108_irq_cascade); +#endif + /* Configure MPIC outputs to CPU0 */ + tsi108_write_reg(TSI108_MPIC_OFFSET + 0x30c, 0); + of_node_put(tsi_pic); +} + +void holly_show_cpuinfo(struct seq_file *m) +{ + seq_printf(m, "vendor\t\t: IBM\n"); + seq_printf(m, "machine\t\t: PPC750 GX/CL\n"); +} + +void holly_restart(char *cmd) +{ + __be32 __iomem *ocn_bar1 = NULL; + unsigned long bar; + struct device_node *bridge = NULL; + const void *prop; + int size; + phys_addr_t addr = 0xc0000000; + + local_irq_disable(); + + bridge = of_find_node_by_type(NULL, "tsi-bridge"); + if (bridge) { + prop = of_get_property(bridge, "reg", &size); + addr = of_translate_address(bridge, prop); + } + addr += (TSI108_PB_OFFSET + 0x414); + + ocn_bar1 = ioremap(addr, 0x4); + + /* Turn on the BOOT bit so the addresses are correctly + * routed to the HLP interface */ + bar = ioread32be(ocn_bar1); + bar |= 2; + iowrite32be(bar, ocn_bar1); + iosync(); + + /* Set SRR0 to the reset vector and turn on MSR_IP */ + mtspr(SPRN_SRR0, 0xfff00100); + mtspr(SPRN_SRR1, MSR_IP); + + /* Do an rfi to jump back to firmware. Somewhat evil, + * but it works + */ + __asm__ __volatile__("rfi" : : : "memory"); + + /* Spin until reset happens. Shouldn't really get here */ + for (;;) ; +} + +void holly_power_off(void) +{ + local_irq_disable(); + /* No way to shut power off with software */ + for (;;) ; +} + +void holly_halt(void) +{ + holly_power_off(); +} + +/* + * Called very early, device-tree isn't unflattened + */ +static int __init holly_probe(void) +{ + unsigned long root = of_get_flat_dt_root(); + + if (!of_flat_dt_is_compatible(root, "ibm,holly")) + return 0; + return 1; +} + +static int ppc750_machine_check_exception(struct pt_regs *regs) +{ + const struct exception_table_entry *entry; + + /* Are we prepared to handle this fault */ + if ((entry = search_exception_tables(regs->nip)) != NULL) { + tsi108_clear_pci_cfg_error(); + regs->msr |= MSR_RI; + regs->nip = entry->fixup; + return 1; + } + return 0; +} + +define_machine(holly){ + .name = "PPC750 GX/CL TSI", + .probe = holly_probe, + .setup_arch = holly_setup_arch, + .init_IRQ = holly_init_IRQ, + .show_cpuinfo = holly_show_cpuinfo, + .get_irq = mpic_get_irq, + .restart = holly_restart, + .calibrate_decr = generic_calibrate_decr, + .machine_check_exception = ppc750_machine_check_exception, + .progress = udbg_progress, +}; diff --git a/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c b/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c index c3f64ddb0be..4542e0c837c 100644 --- a/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c +++ b/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c @@ -41,6 +41,7 @@ #include <asm/reg.h> #include <mm/mmu_decl.h> #include "mpc7448_hpc2.h" +#include <asm/tsi108_pci.h> #include <asm/tsi108_irq.h> #include <asm/mpic.h> @@ -51,16 +52,15 @@ #define DBG(fmt...) do { } while(0) #endif +#define MPC7448HPC2_PCI_CFG_PHYS 0xfb000000 + #ifndef CONFIG_PCI isa_io_base = MPC7448_HPC2_ISA_IO_BASE; isa_mem_base = MPC7448_HPC2_ISA_MEM_BASE; pci_dram_offset = MPC7448_HPC2_PCI_MEM_OFFSET; #endif -extern int tsi108_setup_pci(struct device_node *dev); extern void _nmask_and_or_msr(unsigned long nmask, unsigned long or_val); -extern void tsi108_pci_int_init(struct device_node *node); -extern void tsi108_irq_cascade(unsigned int irq, struct irq_desc *desc); int mpc7448_hpc2_exclude_device(u_char bus, u_char devfn) { @@ -72,28 +72,16 @@ int mpc7448_hpc2_exclude_device(u_char bus, u_char devfn) static void __init mpc7448_hpc2_setup_arch(void) { - struct device_node *cpu; struct device_node *np; if (ppc_md.progress) ppc_md.progress("mpc7448_hpc2_setup_arch():set_bridge", 0); - cpu = of_find_node_by_type(NULL, "cpu"); - if (cpu != 0) { - const unsigned int *fp; - - fp = of_get_property(cpu, "clock-frequency", NULL); - if (fp != 0) - loops_per_jiffy = *fp / HZ; - else - loops_per_jiffy = 50000000 / HZ; - of_node_put(cpu); - } tsi108_csr_vir_base = get_vir_csrbase(); /* setup PCI host bridge */ #ifdef CONFIG_PCI for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;) - tsi108_setup_pci(np); + tsi108_setup_pci(np, MPC7448HPC2_PCI_CFG_PHYS, 0); ppc_md.pci_exclude_device = mpc7448_hpc2_exclude_device; if (ppc_md.progress) @@ -222,7 +210,6 @@ static int __init mpc7448_hpc2_probe(void) static int mpc7448_machine_check_exception(struct pt_regs *regs) { - extern void tsi108_clear_pci_cfg_error(void); const struct exception_table_entry *entry; /* Are we prepared to handle this fault */ diff --git a/arch/powerpc/platforms/maple/pci.c b/arch/powerpc/platforms/maple/pci.c index b1d3b99c3f9..7aaa5bbc936 100644 --- a/arch/powerpc/platforms/maple/pci.c +++ b/arch/powerpc/platforms/maple/pci.c @@ -467,15 +467,15 @@ static int __init add_bridge(struct device_node *dev) hose->last_busno = bus_range ? bus_range[1] : 0xff; disp_name = NULL; - if (device_is_compatible(dev, "u3-agp")) { + if (of_device_is_compatible(dev, "u3-agp")) { setup_u3_agp(hose); disp_name = "U3-AGP"; primary = 0; - } else if (device_is_compatible(dev, "u3-ht")) { + } else if (of_device_is_compatible(dev, "u3-ht")) { setup_u3_ht(hose); disp_name = "U3-HT"; primary = 1; - } else if (device_is_compatible(dev, "u4-pcie")) { + } else if (of_device_is_compatible(dev, "u4-pcie")) { setup_u4_pcie(hose); disp_name = "U4-PCIE"; primary = 0; @@ -556,12 +556,12 @@ void __init maple_pci_init(void) continue; if (strcmp(np->type, "pci") && strcmp(np->type, "ht")) continue; - if ((device_is_compatible(np, "u4-pcie") || - device_is_compatible(np, "u3-agp")) && + if ((of_device_is_compatible(np, "u4-pcie") || + of_device_is_compatible(np, "u3-agp")) && add_bridge(np) == 0) of_node_get(np); - if (device_is_compatible(np, "u3-ht")) { + if (of_device_is_compatible(np, "u3-ht")) { of_node_get(np); ht = np; } diff --git a/arch/powerpc/platforms/maple/setup.c b/arch/powerpc/platforms/maple/setup.c index 2a30c5b2532..354c0586162 100644 --- a/arch/powerpc/platforms/maple/setup.c +++ b/arch/powerpc/platforms/maple/setup.c @@ -231,7 +231,7 @@ static void __init maple_init_IRQ(void) */ for_each_node_by_type(np, "interrupt-controller") - if (device_is_compatible(np, "open-pic")) { + if (of_device_is_compatible(np, "open-pic")) { mpic_node = np; break; } diff --git a/arch/powerpc/platforms/pasemi/cpufreq.c b/arch/powerpc/platforms/pasemi/cpufreq.c index 2a57d602368..3ae083851b0 100644 --- a/arch/powerpc/platforms/pasemi/cpufreq.c +++ b/arch/powerpc/platforms/pasemi/cpufreq.c @@ -31,6 +31,7 @@ #include <asm/hw_irq.h> #include <asm/io.h> #include <asm/prom.h> +#include <asm/time.h> #define SDCASR_REG 0x0100 #define SDCASR_REG_STRIDE 0x1000 @@ -204,6 +205,8 @@ static int pas_cpufreq_cpu_init(struct cpufreq_policy *policy) policy->cur = pas_freqs[cur_astate].frequency; policy->cpus = cpu_online_map; + ppc_proc_freq = policy->cur * 1000ul; + cpufreq_frequency_table_get_attr(pas_freqs, policy->cpu); /* this ensures that policy->cpuinfo_min and policy->cpuinfo_max @@ -270,6 +273,7 @@ static int pas_cpufreq_target(struct cpufreq_policy *policy, cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); mutex_unlock(&pas_switch_mutex); + ppc_proc_freq = freqs.new * 1000ul; return 0; } diff --git a/arch/powerpc/platforms/pasemi/setup.c b/arch/powerpc/platforms/pasemi/setup.c index f88f0ec4c8c..38f107b3c52 100644 --- a/arch/powerpc/platforms/pasemi/setup.c +++ b/arch/powerpc/platforms/pasemi/setup.c @@ -114,7 +114,7 @@ static __init void pas_init_IRQ(void) mpic_node = NULL; for_each_node_by_type(np, "interrupt-controller") - if (device_is_compatible(np, "open-pic")) { + if (of_device_is_compatible(np, "open-pic")) { mpic_node = np; break; } @@ -211,7 +211,10 @@ static struct of_device_id pasemi_bus_ids[] = { static int __init pasemi_publish_devices(void) { - /* Publish OF platform devices for southbridge IOs */ + if (!machine_is(pasemi)) + return 0; + + /* Publish OF platform devices for SDC and other non-PCI devices */ of_platform_bus_probe(NULL, pasemi_bus_ids, NULL); return 0; diff --git a/arch/powerpc/platforms/powermac/cpufreq_64.c b/arch/powerpc/platforms/powermac/cpufreq_64.c index 567d5523b69..00f50298c34 100644 --- a/arch/powerpc/platforms/powermac/cpufreq_64.c +++ b/arch/powerpc/platforms/powermac/cpufreq_64.c @@ -357,13 +357,13 @@ static unsigned int g5_cpufreq_get_speed(unsigned int cpu) static int g5_cpufreq_cpu_init(struct cpufreq_policy *policy) { - if (policy->cpu != 0) - return -ENODEV; - policy->governor = CPUFREQ_DEFAULT_GOVERNOR; policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL; policy->cur = g5_cpu_freqs[g5_query_freq()].frequency; - policy->cpus = cpu_possible_map; + /* secondary CPUs are tied to the primary one by the + * cpufreq core if in the secondary policy we tell it that + * it actually must be one policy together with all others. */ + policy->cpus = cpu_online_map; cpufreq_frequency_table_get_attr(g5_cpu_freqs, policy->cpu); return cpufreq_frequency_table_cpuinfo(policy, diff --git a/arch/powerpc/platforms/powermac/feature.c b/arch/powerpc/platforms/powermac/feature.c index 52cfdd86c92..f29705f8047 100644 --- a/arch/powerpc/platforms/powermac/feature.c +++ b/arch/powerpc/platforms/powermac/feature.c @@ -1418,7 +1418,7 @@ static long g5_eth_phy_reset(struct device_node *node, long param, long value) phy = of_get_next_child(node, NULL); if (!phy) return -ENODEV; - need_reset = device_is_compatible(phy, "B5221"); + need_reset = of_device_is_compatible(phy, "B5221"); of_node_put(phy); if (!need_reset) return 0; @@ -2624,7 +2624,7 @@ static void __init probe_one_macio(const char *name, const char *compat, int typ for (node = NULL; (node = of_find_node_by_name(node, name)) != NULL;) { if (!compat) break; - if (device_is_compatible(node, compat)) + if (of_device_is_compatible(node, compat)) break; } if (!node) @@ -2728,7 +2728,7 @@ initial_serial_shutdown(struct device_node *np) conn = of_get_property(np, "AAPL,connector", &len); if (conn && (strcmp(conn, "infrared") == 0)) port_type = PMAC_SCC_IRDA; - else if (device_is_compatible(np, "cobalt")) + else if (of_device_is_compatible(np, "cobalt")) modem = 1; else if (slots && slots->count > 0) { if (strcmp(slots->name, "IrDA") == 0) @@ -2787,7 +2787,7 @@ set_initial_features(void) */ np = of_find_node_by_name(NULL, "ethernet"); while(np) { - if (device_is_compatible(np, "K2-GMAC")) + if (of_device_is_compatible(np, "K2-GMAC")) g5_gmac_enable(np, 0, 1); np = of_find_node_by_name(np, "ethernet"); } @@ -2799,7 +2799,7 @@ set_initial_features(void) */ np = of_find_node_by_name(NULL, "firewire"); while(np) { - if (device_is_compatible(np, "pci106b,5811")) { + if (of_device_is_compatible(np, "pci106b,5811")) { macio_chips[0].flags |= MACIO_FLAG_FW_SUPPORTED; g5_fw_enable(np, 0, 1); } @@ -2817,8 +2817,8 @@ set_initial_features(void) np = of_find_node_by_name(NULL, "ethernet"); while(np) { if (np->parent - && device_is_compatible(np->parent, "uni-north") - && device_is_compatible(np, "gmac")) + && of_device_is_compatible(np->parent, "uni-north") + && of_device_is_compatible(np, "gmac")) core99_gmac_enable(np, 0, 1); np = of_find_node_by_name(np, "ethernet"); } @@ -2831,10 +2831,10 @@ set_initial_features(void) np = of_find_node_by_name(NULL, "firewire"); while(np) { if (np->parent - && device_is_compatible(np->parent, "uni-north") - && (device_is_compatible(np, "pci106b,18") || - device_is_compatible(np, "pci106b,30") || - device_is_compatible(np, "pci11c1,5811"))) { + && of_device_is_compatible(np->parent, "uni-north") + && (of_device_is_compatible(np, "pci106b,18") || + of_device_is_compatible(np, "pci106b,30") || + of_device_is_compatible(np, "pci11c1,5811"))) { macio_chips[0].flags |= MACIO_FLAG_FW_SUPPORTED; core99_firewire_enable(np, 0, 1); } @@ -2845,8 +2845,8 @@ set_initial_features(void) np = of_find_node_by_name(NULL, "ata-6"); while(np) { if (np->parent - && device_is_compatible(np->parent, "uni-north") - && device_is_compatible(np, "kauai-ata")) { + && of_device_is_compatible(np->parent, "uni-north") + && of_device_is_compatible(np, "kauai-ata")) { core99_ata100_enable(np, 1); } np = of_find_node_by_name(np, "ata-6"); diff --git a/arch/powerpc/platforms/powermac/low_i2c.c b/arch/powerpc/platforms/powermac/low_i2c.c index 5430e146b3e..3f507ab9c5e 100644 --- a/arch/powerpc/platforms/powermac/low_i2c.c +++ b/arch/powerpc/platforms/powermac/low_i2c.c @@ -1207,7 +1207,7 @@ static void pmac_i2c_devscan(void (*callback)(struct device_node *dev, if (strcmp(np->name, p->name)) continue; if (p->compatible && - !device_is_compatible(np, p->compatible)) + !of_device_is_compatible(np, p->compatible)) continue; if (p->quirks & pmac_i2c_quirk_skip) break; diff --git a/arch/powerpc/platforms/powermac/nvram.c b/arch/powerpc/platforms/powermac/nvram.c index 692945c1491..c6f0f9e738e 100644 --- a/arch/powerpc/platforms/powermac/nvram.c +++ b/arch/powerpc/platforms/powermac/nvram.c @@ -553,7 +553,7 @@ static int __init core99_nvram_setup(struct device_node *dp, unsigned long addr) * identify the chip using flash id commands and base ourselves on * a list of known chips IDs */ - if (device_is_compatible(dp, "amd-0137")) { + if (of_device_is_compatible(dp, "amd-0137")) { core99_erase_bank = amd_erase_bank; core99_write_bank = amd_write_bank; } else { @@ -588,7 +588,7 @@ int __init pmac_nvram_init(void) } } - is_core_99 = device_is_compatible(dp, "nvram,flash"); + is_core_99 = of_device_is_compatible(dp, "nvram,flash"); if (is_core_99) { err = core99_nvram_setup(dp, r1.start); goto bail; diff --git a/arch/powerpc/platforms/powermac/pci.c b/arch/powerpc/platforms/powermac/pci.c index 22c4ae4c693..c4af9e21ac9 100644 --- a/arch/powerpc/platforms/powermac/pci.c +++ b/arch/powerpc/platforms/powermac/pci.c @@ -934,15 +934,15 @@ static int __init add_bridge(struct device_node *dev) /* 64 bits only bridges */ #ifdef CONFIG_PPC64 - if (device_is_compatible(dev, "u3-agp")) { + if (of_device_is_compatible(dev, "u3-agp")) { setup_u3_agp(hose); disp_name = "U3-AGP"; primary = 0; - } else if (device_is_compatible(dev, "u3-ht")) { + } else if (of_device_is_compatible(dev, "u3-ht")) { setup_u3_ht(hose); disp_name = "U3-HT"; primary = 1; - } else if (device_is_compatible(dev, "u4-pcie")) { + } else if (of_device_is_compatible(dev, "u4-pcie")) { setup_u4_pcie(hose); disp_name = "U4-PCIE"; primary = 0; @@ -953,7 +953,7 @@ static int __init add_bridge(struct device_node *dev) /* 32 bits only bridges */ #ifdef CONFIG_PPC32 - if (device_is_compatible(dev, "uni-north")) { + if (of_device_is_compatible(dev, "uni-north")) { primary = setup_uninorth(hose, &rsrc); disp_name = "UniNorth"; } else if (strcmp(dev->name, "pci") == 0) { @@ -1129,21 +1129,21 @@ pmac_pci_enable_device_hook(struct pci_dev *dev, int initial) return 0; uninorth_child = node->parent && - device_is_compatible(node->parent, "uni-north"); + of_device_is_compatible(node->parent, "uni-north"); /* Firewire & GMAC were disabled after PCI probe, the driver is * claiming them, we must re-enable them now. */ if (uninorth_child && !strcmp(node->name, "firewire") && - (device_is_compatible(node, "pci106b,18") || - device_is_compatible(node, "pci106b,30") || - device_is_compatible(node, "pci11c1,5811"))) { + (of_device_is_compatible(node, "pci106b,18") || + of_device_is_compatible(node, "pci106b,30") || + of_device_is_compatible(node, "pci11c1,5811"))) { pmac_call_feature(PMAC_FTR_1394_CABLE_POWER, node, 0, 1); pmac_call_feature(PMAC_FTR_1394_ENABLE, node, 0, 1); updatecfg = 1; } if (uninorth_child && !strcmp(node->name, "ethernet") && - device_is_compatible(node, "gmac")) { + of_device_is_compatible(node, "gmac")) { pmac_call_feature(PMAC_FTR_GMAC_ENABLE, node, 0, 1); updatecfg = 1; } @@ -1203,18 +1203,18 @@ void __init pmac_pcibios_after_init(void) #endif /* CONFIG_BLK_DEV_IDE */ for_each_node_by_name(nd, "firewire") { - if (nd->parent && (device_is_compatible(nd, "pci106b,18") || - device_is_compatible(nd, "pci106b,30") || - device_is_compatible(nd, "pci11c1,5811")) - && device_is_compatible(nd->parent, "uni-north")) { + if (nd->parent && (of_device_is_compatible(nd, "pci106b,18") || + of_device_is_compatible(nd, "pci106b,30") || + of_device_is_compatible(nd, "pci11c1,5811")) + && of_device_is_compatible(nd->parent, "uni-north")) { pmac_call_feature(PMAC_FTR_1394_ENABLE, nd, 0, 0); pmac_call_feature(PMAC_FTR_1394_CABLE_POWER, nd, 0, 0); } } of_node_put(nd); for_each_node_by_name(nd, "ethernet") { - if (nd->parent && device_is_compatible(nd, "gmac") - && device_is_compatible(nd->parent, "uni-north")) + if (nd->parent && of_device_is_compatible(nd, "gmac") + && of_device_is_compatible(nd->parent, "uni-north")) pmac_call_feature(PMAC_FTR_GMAC_ENABLE, nd, 0, 0); } of_node_put(nd); diff --git a/arch/powerpc/platforms/powermac/pic.c b/arch/powerpc/platforms/powermac/pic.c index ae5097ac037..87cd6805171 100644 --- a/arch/powerpc/platforms/powermac/pic.c +++ b/arch/powerpc/platforms/powermac/pic.c @@ -364,7 +364,7 @@ static void __init pmac_pic_probe_oldstyle(void) slave = of_find_node_by_name(master, "mac-io"); /* Check ordering of master & slave */ - if (device_is_compatible(master, "gatwick")) { + if (of_device_is_compatible(master, "gatwick")) { struct device_node *tmp; BUG_ON(slave == NULL); tmp = master; diff --git a/arch/powerpc/platforms/powermac/setup.c b/arch/powerpc/platforms/powermac/setup.c index b820cabac69..a410bc76a8a 100644 --- a/arch/powerpc/platforms/powermac/setup.c +++ b/arch/powerpc/platforms/powermac/setup.c @@ -439,76 +439,14 @@ static void __init find_boot_device(void) #endif } -/* TODO: Merge the suspend-to-ram with the common code !!! - * currently, this is a stub implementation for suspend-to-disk - * only - */ - -#ifdef CONFIG_SOFTWARE_SUSPEND - -static int pmac_pm_prepare(suspend_state_t state) -{ - printk(KERN_DEBUG "%s(%d)\n", __FUNCTION__, state); - - return 0; -} - -static int pmac_pm_enter(suspend_state_t state) -{ - printk(KERN_DEBUG "%s(%d)\n", __FUNCTION__, state); - - /* Giveup the lazy FPU & vec so we don't have to back them - * up from the low level code - */ - enable_kernel_fp(); - -#ifdef CONFIG_ALTIVEC - if (cur_cpu_spec->cpu_features & CPU_FTR_ALTIVEC) - enable_kernel_altivec(); -#endif /* CONFIG_ALTIVEC */ - - return 0; -} - -static int pmac_pm_finish(suspend_state_t state) -{ - printk(KERN_DEBUG "%s(%d)\n", __FUNCTION__, state); - - /* Restore userland MMU context */ - set_context(current->active_mm->context.id, current->active_mm->pgd); - - return 0; -} - -static int pmac_pm_valid(suspend_state_t state) -{ - switch (state) { - case PM_SUSPEND_DISK: - return 1; - /* can't do any other states via generic mechanism yet */ - default: - return 0; - } -} - -static struct pm_ops pmac_pm_ops = { - .pm_disk_mode = PM_DISK_SHUTDOWN, - .prepare = pmac_pm_prepare, - .enter = pmac_pm_enter, - .finish = pmac_pm_finish, - .valid = pmac_pm_valid, -}; - -#endif /* CONFIG_SOFTWARE_SUSPEND */ - static int initializing = 1; static int pmac_late_init(void) { initializing = 0; -#ifdef CONFIG_SOFTWARE_SUSPEND - pm_set_ops(&pmac_pm_ops); -#endif /* CONFIG_SOFTWARE_SUSPEND */ + /* this is udbg (which is __init) and we can later use it during + * cpu hotplug (in smp_core99_kick_cpu) */ + ppc_md.progress = NULL; return 0; } @@ -721,12 +659,57 @@ static int pmac_pci_probe_mode(struct pci_bus *bus) /* We need to use normal PCI probing for the AGP bus, * since the device for the AGP bridge isn't in the tree. */ - if (bus->self == NULL && (device_is_compatible(node, "u3-agp") || - device_is_compatible(node, "u4-pcie"))) + if (bus->self == NULL && (of_device_is_compatible(node, "u3-agp") || + of_device_is_compatible(node, "u4-pcie"))) return PCI_PROBE_NORMAL; return PCI_PROBE_DEVTREE; } -#endif + +#ifdef CONFIG_HOTPLUG_CPU +/* access per cpu vars from generic smp.c */ +DECLARE_PER_CPU(int, cpu_state); + +static void pmac_cpu_die(void) +{ + /* + * turn off as much as possible, we'll be + * kicked out as this will only be invoked + * on core99 platforms for now ... + */ + + printk(KERN_INFO "CPU#%d offline\n", smp_processor_id()); + __get_cpu_var(cpu_state) = CPU_DEAD; + smp_wmb(); + + /* + * during the path that leads here preemption is disabled, + * reenable it now so that when coming up preempt count is + * zero correctly + */ + preempt_enable(); + + /* + * hard-disable interrupts for the non-NAP case, the NAP code + * needs to re-enable interrupts (but soft-disables them) + */ + hard_irq_disable(); + + while (1) { + /* let's not take timer interrupts too often ... */ + set_dec(0x7fffffff); + + /* should always be true at this point */ + if (cpu_has_feature(CPU_FTR_CAN_NAP)) + power4_cpu_offline_powersave(); + else { + HMT_low(); + HMT_very_low(); + } + } +} +#endif /* CONFIG_HOTPLUG_CPU */ + +#endif /* CONFIG_PPC64 */ define_machine(powermac) { .name = "PowerMac", @@ -763,6 +746,6 @@ define_machine(powermac) { .phys_mem_access_prot = pci_phys_mem_access_prot, #endif #if defined(CONFIG_HOTPLUG_CPU) && defined(CONFIG_PPC64) - .cpu_die = generic_mach_cpu_die, + .cpu_die = pmac_cpu_die, #endif }; diff --git a/arch/powerpc/platforms/powermac/smp.c b/arch/powerpc/platforms/powermac/smp.c index 6f32c4eca6e..84f1860493b 100644 --- a/arch/powerpc/platforms/powermac/smp.c +++ b/arch/powerpc/platforms/powermac/smp.c @@ -562,7 +562,7 @@ static void __init smp_core99_setup_i2c_hwsync(int ncpus) /* Look for the clock chip */ while ((cc = of_find_node_by_name(cc, "i2c-hwclock")) != NULL) { p = of_get_parent(cc); - ok = p && device_is_compatible(p, "uni-n-i2c"); + ok = p && of_device_is_compatible(p, "uni-n-i2c"); of_node_put(p); if (!ok) continue; @@ -575,11 +575,11 @@ static void __init smp_core99_setup_i2c_hwsync(int ncpus) continue; switch (*reg) { case 0xd2: - if (device_is_compatible(cc,"pulsar-legacy-slewing")) { + if (of_device_is_compatible(cc,"pulsar-legacy-slewing")) { pmac_tb_freeze = smp_core99_pulsar_tb_freeze; pmac_tb_pulsar_addr = 0xd2; name = "Pulsar"; - } else if (device_is_compatible(cc, "cy28508")) { + } else if (of_device_is_compatible(cc, "cy28508")) { pmac_tb_freeze = smp_core99_cypress_tb_freeze; name = "Cypress"; } @@ -900,7 +900,7 @@ void smp_core99_cpu_die(unsigned int cpu) cpu_dead[cpu] = 0; } -#endif +#endif /* CONFIG_HOTPLUG_CPU && CONFIG_PP32 */ /* Core99 Macs (dual G4s and G5s) */ struct smp_ops_t core99_smp_ops = { @@ -910,8 +910,16 @@ struct smp_ops_t core99_smp_ops = { .setup_cpu = smp_core99_setup_cpu, .give_timebase = smp_core99_give_timebase, .take_timebase = smp_core99_take_timebase, -#if defined(CONFIG_HOTPLUG_CPU) && defined(CONFIG_PPC32) +#if defined(CONFIG_HOTPLUG_CPU) +# if defined(CONFIG_PPC32) .cpu_disable = smp_core99_cpu_disable, .cpu_die = smp_core99_cpu_die, +# endif +# if defined(CONFIG_PPC64) + .cpu_disable = generic_cpu_disable, + .cpu_die = generic_cpu_die, + /* intentionally do *NOT* assign cpu_enable, + * the generic code will use kick_cpu then! */ +# endif #endif }; diff --git a/arch/powerpc/platforms/ps3/htab.c b/arch/powerpc/platforms/ps3/htab.c index ea60c451cf8..a1409e450c7 100644 --- a/arch/powerpc/platforms/ps3/htab.c +++ b/arch/powerpc/platforms/ps3/htab.c @@ -273,7 +273,8 @@ void __init ps3_map_htab(void) result = lv1_map_htab(0, &htab_addr); - htab = (hpte_t *)__ioremap(htab_addr, htab_size, PAGE_READONLY_X); + htab = (hpte_t *)__ioremap(htab_addr, htab_size, + pgprot_val(PAGE_READONLY_X)); DBG("%s:%d: lpar %016lxh, virt %016lxh\n", __func__, __LINE__, htab_addr, (unsigned long)htab); diff --git a/arch/powerpc/platforms/ps3/interrupt.c b/arch/powerpc/platforms/ps3/interrupt.c index 631c3009561..9da82c266ba 100644 --- a/arch/powerpc/platforms/ps3/interrupt.c +++ b/arch/powerpc/platforms/ps3/interrupt.c @@ -89,7 +89,18 @@ struct ps3_private { static DEFINE_PER_CPU(struct ps3_private, ps3_private); -int ps3_alloc_irq(enum ps3_cpu_binding cpu, unsigned long outlet, +/** + * ps3_virq_setup - virq related setup. + * @cpu: enum ps3_cpu_binding indicating the cpu the interrupt should be + * serviced on. + * @outlet: The HV outlet from the various create outlet routines. + * @virq: The assigned Linux virq. + * + * Calls irq_create_mapping() to get a virq and sets the chip data to + * ps3_private data. + */ + +int ps3_virq_setup(enum ps3_cpu_binding cpu, unsigned long outlet, unsigned int *virq) { int result; @@ -111,17 +122,6 @@ int ps3_alloc_irq(enum ps3_cpu_binding cpu, unsigned long outlet, goto fail_create; } - /* Binds outlet to cpu + virq. */ - - result = lv1_connect_irq_plug_ext(pd->node, pd->cpu, *virq, outlet, 0); - - if (result) { - pr_info("%s:%d: lv1_connect_irq_plug_ext failed: %s\n", - __func__, __LINE__, ps3_result(result)); - result = -EPERM; - goto fail_connect; - } - pr_debug("%s:%d: outlet %lu => cpu %u, virq %u\n", __func__, __LINE__, outlet, cpu, *virq); @@ -136,94 +136,118 @@ int ps3_alloc_irq(enum ps3_cpu_binding cpu, unsigned long outlet, return result; fail_set: - lv1_disconnect_irq_plug_ext(pd->node, pd->cpu, *virq); -fail_connect: irq_dispose_mapping(*virq); fail_create: return result; } -EXPORT_SYMBOL_GPL(ps3_alloc_irq); -int ps3_free_irq(unsigned int virq) +/** + * ps3_virq_destroy - virq related teardown. + * @virq: The assigned Linux virq. + * + * Clears chip data and calls irq_dispose_mapping() for the virq. + */ + +int ps3_virq_destroy(unsigned int virq) { - int result; const struct ps3_private *pd = get_irq_chip_data(virq); pr_debug("%s:%d: node %lu, cpu %d, virq %u\n", __func__, __LINE__, pd->node, pd->cpu, virq); - result = lv1_disconnect_irq_plug_ext(pd->node, pd->cpu, virq); - - if (result) - pr_info("%s:%d: lv1_disconnect_irq_plug_ext failed: %s\n", - __func__, __LINE__, ps3_result(result)); - set_irq_chip_data(virq, NULL); irq_dispose_mapping(virq); - return result; + + pr_debug("%s:%d <-\n", __func__, __LINE__); + return 0; } -EXPORT_SYMBOL_GPL(ps3_free_irq); /** - * ps3_alloc_io_irq - Assign a virq to a system bus device. + * ps3_irq_plug_setup - Generic outlet and virq related setup. * @cpu: enum ps3_cpu_binding indicating the cpu the interrupt should be * serviced on. - * @interrupt_id: The device interrupt id read from the system repository. + * @outlet: The HV outlet from the various create outlet routines. * @virq: The assigned Linux virq. * - * An io irq represents a non-virtualized device interrupt. interrupt_id - * coresponds to the interrupt number of the interrupt controller. + * Sets up virq and connects the irq plug. */ -int ps3_alloc_io_irq(enum ps3_cpu_binding cpu, unsigned int interrupt_id, +int ps3_irq_plug_setup(enum ps3_cpu_binding cpu, unsigned long outlet, unsigned int *virq) { int result; - unsigned long outlet; + struct ps3_private *pd; - result = lv1_construct_io_irq_outlet(interrupt_id, &outlet); + result = ps3_virq_setup(cpu, outlet, virq); if (result) { - pr_debug("%s:%d: lv1_construct_io_irq_outlet failed: %s\n", - __func__, __LINE__, ps3_result(result)); - return result; + pr_debug("%s:%d: ps3_virq_setup failed\n", __func__, __LINE__); + goto fail_setup; } - result = ps3_alloc_irq(cpu, outlet, virq); - BUG_ON(result); + pd = get_irq_chip_data(*virq); + + /* Binds outlet to cpu + virq. */ + + result = lv1_connect_irq_plug_ext(pd->node, pd->cpu, *virq, outlet, 0); + if (result) { + pr_info("%s:%d: lv1_connect_irq_plug_ext failed: %s\n", + __func__, __LINE__, ps3_result(result)); + result = -EPERM; + goto fail_connect; + } + + return result; + +fail_connect: + ps3_virq_destroy(*virq); +fail_setup: return result; } -EXPORT_SYMBOL_GPL(ps3_alloc_io_irq); +EXPORT_SYMBOL_GPL(ps3_irq_plug_setup); + +/** + * ps3_irq_plug_destroy - Generic outlet and virq related teardown. + * @virq: The assigned Linux virq. + * + * Disconnects the irq plug and tears down virq. + * Do not call for system bus event interrupts setup with + * ps3_sb_event_receive_port_setup(). + */ -int ps3_free_io_irq(unsigned int virq) +int ps3_irq_plug_destroy(unsigned int virq) { int result; + const struct ps3_private *pd = get_irq_chip_data(virq); - result = lv1_destruct_io_irq_outlet(virq_to_hw(virq)); + pr_debug("%s:%d: node %lu, cpu %d, virq %u\n", __func__, __LINE__, + pd->node, pd->cpu, virq); + + result = lv1_disconnect_irq_plug_ext(pd->node, pd->cpu, virq); if (result) - pr_debug("%s:%d: lv1_destruct_io_irq_outlet failed: %s\n", - __func__, __LINE__, ps3_result(result)); + pr_info("%s:%d: lv1_disconnect_irq_plug_ext failed: %s\n", + __func__, __LINE__, ps3_result(result)); - ps3_free_irq(virq); + ps3_virq_destroy(virq); return result; } -EXPORT_SYMBOL_GPL(ps3_free_io_irq); +EXPORT_SYMBOL_GPL(ps3_irq_plug_destroy); /** - * ps3_alloc_event_irq - Allocate a virq for use with a system event. + * ps3_event_receive_port_setup - Setup an event receive port. * @cpu: enum ps3_cpu_binding indicating the cpu the interrupt should be * serviced on. * @virq: The assigned Linux virq. * * The virq can be used with lv1_connect_interrupt_event_receive_port() to - * arrange to receive events, or with ps3_send_event_locally() to signal - * events. + * arrange to receive interrupts from system-bus devices, or with + * ps3_send_event_locally() to signal events. */ -int ps3_alloc_event_irq(enum ps3_cpu_binding cpu, unsigned int *virq) +int ps3_event_receive_port_setup(enum ps3_cpu_binding cpu, unsigned int *virq) { int result; unsigned long outlet; @@ -237,17 +261,27 @@ int ps3_alloc_event_irq(enum ps3_cpu_binding cpu, unsigned int *virq) return result; } - result = ps3_alloc_irq(cpu, outlet, virq); + result = ps3_irq_plug_setup(cpu, outlet, virq); BUG_ON(result); return result; } +EXPORT_SYMBOL_GPL(ps3_event_receive_port_setup); + +/** + * ps3_event_receive_port_destroy - Destroy an event receive port. + * @virq: The assigned Linux virq. + * + * Since ps3_event_receive_port_destroy destroys the receive port outlet, + * SB devices need to call disconnect_interrupt_event_receive_port() before + * this. + */ -int ps3_free_event_irq(unsigned int virq) +int ps3_event_receive_port_destroy(unsigned int virq) { int result; - pr_debug(" -> %s:%d\n", __func__, __LINE__); + pr_debug(" -> %s:%d virq: %u\n", __func__, __LINE__, virq); result = lv1_destruct_event_receive_port(virq_to_hw(virq)); @@ -255,11 +289,17 @@ int ps3_free_event_irq(unsigned int virq) pr_debug("%s:%d: lv1_destruct_event_receive_port failed: %s\n", __func__, __LINE__, ps3_result(result)); - ps3_free_irq(virq); + /* lv1_destruct_event_receive_port() destroys the IRQ plug, + * so don't call ps3_irq_plug_destroy() here. + */ + + result = ps3_virq_destroy(virq); + BUG_ON(result); pr_debug(" <- %s:%d\n", __func__, __LINE__); return result; } +EXPORT_SYMBOL_GPL(ps3_event_receive_port_destroy); int ps3_send_event_locally(unsigned int virq) { @@ -267,7 +307,7 @@ int ps3_send_event_locally(unsigned int virq) } /** - * ps3_connect_event_irq - Assign a virq to a system bus device. + * ps3_sb_event_receive_port_setup - Setup a system bus event receive port. * @cpu: enum ps3_cpu_binding indicating the cpu the interrupt should be * serviced on. * @did: The HV device identifier read from the system repository. @@ -278,13 +318,15 @@ int ps3_send_event_locally(unsigned int virq) * coresponds to the software interrupt number. */ -int ps3_connect_event_irq(enum ps3_cpu_binding cpu, +int ps3_sb_event_receive_port_setup(enum ps3_cpu_binding cpu, const struct ps3_device_id *did, unsigned int interrupt_id, unsigned int *virq) { + /* this should go in system-bus.c */ + int result; - result = ps3_alloc_event_irq(cpu, virq); + result = ps3_event_receive_port_setup(cpu, virq); if (result) return result; @@ -296,7 +338,7 @@ int ps3_connect_event_irq(enum ps3_cpu_binding cpu, pr_debug("%s:%d: lv1_connect_interrupt_event_receive_port" " failed: %s\n", __func__, __LINE__, ps3_result(result)); - ps3_free_event_irq(*virq); + ps3_event_receive_port_destroy(*virq); *virq = NO_IRQ; return result; } @@ -306,10 +348,13 @@ int ps3_connect_event_irq(enum ps3_cpu_binding cpu, return 0; } +EXPORT_SYMBOL(ps3_sb_event_receive_port_setup); -int ps3_disconnect_event_irq(const struct ps3_device_id *did, +int ps3_sb_event_receive_port_destroy(const struct ps3_device_id *did, unsigned int interrupt_id, unsigned int virq) { + /* this should go in system-bus.c */ + int result; pr_debug(" -> %s:%d: interrupt_id %u, virq %u\n", __func__, __LINE__, @@ -323,14 +368,65 @@ int ps3_disconnect_event_irq(const struct ps3_device_id *did, " failed: %s\n", __func__, __LINE__, ps3_result(result)); - ps3_free_event_irq(virq); + result = ps3_event_receive_port_destroy(virq); + BUG_ON(result); pr_debug(" <- %s:%d\n", __func__, __LINE__); return result; } +EXPORT_SYMBOL(ps3_sb_event_receive_port_destroy); /** - * ps3_alloc_vuart_irq - Configure the system virtual uart virq. + * ps3_io_irq_setup - Setup a system bus io irq. + * @cpu: enum ps3_cpu_binding indicating the cpu the interrupt should be + * serviced on. + * @interrupt_id: The device interrupt id read from the system repository. + * @virq: The assigned Linux virq. + * + * An io irq represents a non-virtualized device interrupt. interrupt_id + * coresponds to the interrupt number of the interrupt controller. + */ + +int ps3_io_irq_setup(enum ps3_cpu_binding cpu, unsigned int interrupt_id, + unsigned int *virq) +{ + int result; + unsigned long outlet; + + result = lv1_construct_io_irq_outlet(interrupt_id, &outlet); + + if (result) { + pr_debug("%s:%d: lv1_construct_io_irq_outlet failed: %s\n", + __func__, __LINE__, ps3_result(result)); + return result; + } + + result = ps3_irq_plug_setup(cpu, outlet, virq); + BUG_ON(result); + + return result; +} +EXPORT_SYMBOL_GPL(ps3_io_irq_setup); + +int ps3_io_irq_destroy(unsigned int virq) +{ + int result; + + result = lv1_destruct_io_irq_outlet(virq_to_hw(virq)); + + if (result) + pr_debug("%s:%d: lv1_destruct_io_irq_outlet failed: %s\n", + __func__, __LINE__, ps3_result(result)); + + result = ps3_irq_plug_destroy(virq); + BUG_ON(result); + + return result; +} +EXPORT_SYMBOL_GPL(ps3_io_irq_destroy); + +/** + * ps3_vuart_irq_setup - Setup the system virtual uart virq. * @cpu: enum ps3_cpu_binding indicating the cpu the interrupt should be * serviced on. * @virt_addr_bmp: The caller supplied virtual uart interrupt bitmap. @@ -340,7 +436,7 @@ int ps3_disconnect_event_irq(const struct ps3_device_id *did, * freeing the interrupt will return a wrong state error. */ -int ps3_alloc_vuart_irq(enum ps3_cpu_binding cpu, void* virt_addr_bmp, +int ps3_vuart_irq_setup(enum ps3_cpu_binding cpu, void* virt_addr_bmp, unsigned int *virq) { int result; @@ -359,13 +455,13 @@ int ps3_alloc_vuart_irq(enum ps3_cpu_binding cpu, void* virt_addr_bmp, return result; } - result = ps3_alloc_irq(cpu, outlet, virq); + result = ps3_irq_plug_setup(cpu, outlet, virq); BUG_ON(result); return result; } -int ps3_free_vuart_irq(unsigned int virq) +int ps3_vuart_irq_destroy(unsigned int virq) { int result; @@ -377,13 +473,14 @@ int ps3_free_vuart_irq(unsigned int virq) return result; } - ps3_free_irq(virq); + result = ps3_irq_plug_destroy(virq); + BUG_ON(result); return result; } /** - * ps3_alloc_spe_irq - Configure an spe virq. + * ps3_spe_irq_setup - Setup an spe virq. * @cpu: enum ps3_cpu_binding indicating the cpu the interrupt should be * serviced on. * @spe_id: The spe_id returned from lv1_construct_logical_spe(). @@ -392,7 +489,7 @@ int ps3_free_vuart_irq(unsigned int virq) * */ -int ps3_alloc_spe_irq(enum ps3_cpu_binding cpu, unsigned long spe_id, +int ps3_spe_irq_setup(enum ps3_cpu_binding cpu, unsigned long spe_id, unsigned int class, unsigned int *virq) { int result; @@ -408,15 +505,16 @@ int ps3_alloc_spe_irq(enum ps3_cpu_binding cpu, unsigned long spe_id, return result; } - result = ps3_alloc_irq(cpu, outlet, virq); + result = ps3_irq_plug_setup(cpu, outlet, virq); BUG_ON(result); return result; } -int ps3_free_spe_irq(unsigned int virq) +int ps3_spe_irq_destroy(unsigned int virq) { - ps3_free_irq(virq); + int result = ps3_irq_plug_destroy(virq); + BUG_ON(result); return 0; } diff --git a/arch/powerpc/platforms/ps3/mm.c b/arch/powerpc/platforms/ps3/mm.c index 2014d2b4444..f8a3e206c58 100644 --- a/arch/powerpc/platforms/ps3/mm.c +++ b/arch/powerpc/platforms/ps3/mm.c @@ -826,5 +826,4 @@ void __init ps3_mm_init(void) void ps3_mm_shutdown(void) { ps3_mm_region_destroy(&map.r1); - map.total = map.rm.size; } diff --git a/arch/powerpc/platforms/ps3/setup.c b/arch/powerpc/platforms/ps3/setup.c index ac5df9688dc..c9894933084 100644 --- a/arch/powerpc/platforms/ps3/setup.c +++ b/arch/powerpc/platforms/ps3/setup.c @@ -137,6 +137,12 @@ early_param("ps3fb", early_parse_ps3fb); #define prealloc_ps3fb_videomemory() do { } while (0) #endif +static int ps3_set_dabr(u64 dabr) +{ + enum {DABR_USER = 1, DABR_KERNEL = 2,}; + + return lv1_set_dabr(dabr, DABR_KERNEL | DABR_USER) ? -1 : 0; +} static void __init ps3_setup_arch(void) { @@ -234,6 +240,7 @@ define_machine(ps3) { .get_boot_time = ps3_get_boot_time, .set_rtc_time = ps3_set_rtc_time, .get_rtc_time = ps3_get_rtc_time, + .set_dabr = ps3_set_dabr, .calibrate_decr = ps3_calibrate_decr, .progress = ps3_progress, .restart = ps3_restart, diff --git a/arch/powerpc/platforms/ps3/smp.c b/arch/powerpc/platforms/ps3/smp.c index 6fb887961a6..8729348c060 100644 --- a/arch/powerpc/platforms/ps3/smp.c +++ b/arch/powerpc/platforms/ps3/smp.c @@ -110,7 +110,7 @@ static void __init ps3_smp_setup_cpu(int cpu) BUILD_BUG_ON(PPC_MSG_DEBUGGER_BREAK != 3); for (i = 0; i < MSG_COUNT; i++) { - result = ps3_alloc_event_irq(cpu, &virqs[i]); + result = ps3_event_receive_port_setup(cpu, &virqs[i]); if (result) continue; @@ -134,11 +134,13 @@ void ps3_smp_cleanup_cpu(int cpu) int i; DBG(" -> %s:%d: (%d)\n", __func__, __LINE__, cpu); + for (i = 0; i < MSG_COUNT; i++) { - ps3_free_event_irq(virqs[i]); free_irq(virqs[i], (void*)(long)i); + ps3_event_receive_port_destroy(virqs[i]); virqs[i] = NO_IRQ; } + DBG(" <- %s:%d: (%d)\n", __func__, __LINE__, cpu); } diff --git a/arch/powerpc/platforms/ps3/spu.c b/arch/powerpc/platforms/ps3/spu.c index a397e4e17c1..651437cb2c1 100644 --- a/arch/powerpc/platforms/ps3/spu.c +++ b/arch/powerpc/platforms/ps3/spu.c @@ -184,7 +184,7 @@ static int __init setup_areas(struct spu *spu) spu_pdata(spu)->shadow = __ioremap( spu_pdata(spu)->shadow_addr, sizeof(struct spe_shadow), - PAGE_READONLY | _PAGE_NO_CACHE | _PAGE_GUARDED); + pgprot_val(PAGE_READONLY) | _PAGE_NO_CACHE | _PAGE_GUARDED); if (!spu_pdata(spu)->shadow) { pr_debug("%s:%d: ioremap shadow failed\n", __func__, __LINE__); goto fail_ioremap; @@ -230,19 +230,19 @@ static int __init setup_interrupts(struct spu *spu) { int result; - result = ps3_alloc_spe_irq(PS3_BINDING_CPU_ANY, spu_pdata(spu)->spe_id, + result = ps3_spe_irq_setup(PS3_BINDING_CPU_ANY, spu_pdata(spu)->spe_id, 0, &spu->irqs[0]); if (result) goto fail_alloc_0; - result = ps3_alloc_spe_irq(PS3_BINDING_CPU_ANY, spu_pdata(spu)->spe_id, + result = ps3_spe_irq_setup(PS3_BINDING_CPU_ANY, spu_pdata(spu)->spe_id, 1, &spu->irqs[1]); if (result) goto fail_alloc_1; - result = ps3_alloc_spe_irq(PS3_BINDING_CPU_ANY, spu_pdata(spu)->spe_id, + result = ps3_spe_irq_setup(PS3_BINDING_CPU_ANY, spu_pdata(spu)->spe_id, 2, &spu->irqs[2]); if (result) @@ -251,9 +251,9 @@ static int __init setup_interrupts(struct spu *spu) return result; fail_alloc_2: - ps3_free_spe_irq(spu->irqs[1]); + ps3_spe_irq_destroy(spu->irqs[1]); fail_alloc_1: - ps3_free_spe_irq(spu->irqs[0]); + ps3_spe_irq_destroy(spu->irqs[0]); fail_alloc_0: spu->irqs[0] = spu->irqs[1] = spu->irqs[2] = NO_IRQ; return result; @@ -301,9 +301,9 @@ static int ps3_destroy_spu(struct spu *spu) result = lv1_disable_logical_spe(spu_pdata(spu)->spe_id, 0); BUG_ON(result); - ps3_free_spe_irq(spu->irqs[2]); - ps3_free_spe_irq(spu->irqs[1]); - ps3_free_spe_irq(spu->irqs[0]); + ps3_spe_irq_destroy(spu->irqs[2]); + ps3_spe_irq_destroy(spu->irqs[1]); + ps3_spe_irq_destroy(spu->irqs[0]); spu->irqs[0] = spu->irqs[1] = spu->irqs[2] = NO_IRQ; diff --git a/arch/powerpc/platforms/pseries/iommu.c b/arch/powerpc/platforms/pseries/iommu.c index 66665c82415..eec684a8e44 100644 --- a/arch/powerpc/platforms/pseries/iommu.c +++ b/arch/powerpc/platforms/pseries/iommu.c @@ -504,6 +504,12 @@ static void pci_dma_dev_setup_pSeriesLP(struct pci_dev *dev) break; } + if (!pdn || !PCI_DN(pdn)) { + printk(KERN_WARNING "pci_dma_dev_setup_pSeriesLP: " + "no DMA window found for pci dev=%s dn=%s\n", + pci_name(dev), dn? dn->full_name : "<null>"); + return; + } DBG(" parent is %s\n", pdn->full_name); /* Check for parent == NULL so we don't try to setup the empty EADS diff --git a/arch/powerpc/platforms/pseries/lpar.c b/arch/powerpc/platforms/pseries/lpar.c index 3a70e8ad7bc..362dfbc260a 100644 --- a/arch/powerpc/platforms/pseries/lpar.c +++ b/arch/powerpc/platforms/pseries/lpar.c @@ -231,13 +231,13 @@ void __init find_udbg_vterm(void) goto out; vtermno = termno[0]; - if (device_is_compatible(stdout_node, "hvterm1")) { + if (of_device_is_compatible(stdout_node, "hvterm1")) { udbg_putc = udbg_putcLP; udbg_getc = udbg_getcLP; udbg_getc_poll = udbg_getc_pollLP; if (add_console) add_preferred_console("hvc", termno[0] & 0xff, NULL); - } else if (device_is_compatible(stdout_node, "hvterm-protocol")) { + } else if (of_device_is_compatible(stdout_node, "hvterm-protocol")) { vtermno = termno[0]; udbg_putc = udbg_hvsi_putc; udbg_getc = udbg_hvsi_getc; diff --git a/arch/powerpc/platforms/pseries/pci_dlpar.c b/arch/powerpc/platforms/pseries/pci_dlpar.c index fdc1a369f76..ffaf6c5c517 100644 --- a/arch/powerpc/platforms/pseries/pci_dlpar.c +++ b/arch/powerpc/platforms/pseries/pci_dlpar.c @@ -79,6 +79,7 @@ pcibios_remove_pci_devices(struct pci_bus *bus) pci_remove_bus_device(dev); } } +EXPORT_SYMBOL_GPL(pcibios_remove_pci_devices); /* Must be called before pci_bus_add_devices */ void diff --git a/arch/powerpc/platforms/pseries/setup.c b/arch/powerpc/platforms/pseries/setup.c index 33eec2822c6..470db6efaeb 100644 --- a/arch/powerpc/platforms/pseries/setup.c +++ b/arch/powerpc/platforms/pseries/setup.c @@ -168,7 +168,7 @@ static void __init pseries_mpic_init_IRQ(void) /* Look for cascade */ for_each_node_by_type(np, "interrupt-controller") - if (device_is_compatible(np, "chrp,iic")) { + if (of_device_is_compatible(np, "chrp,iic")) { cascade = np; break; } diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index 896cbf340c4..b854e7f1001 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -477,7 +477,7 @@ static int xics_host_match(struct irq_host *h, struct device_node *node) * like vdevices, events, etc... The trick we use here is to match * everything here except the legacy 8259 which is compatible "chrp,iic" */ - return !device_is_compatible(node, "chrp,iic"); + return !of_device_is_compatible(node, "chrp,iic"); } static int xics_host_map_direct(struct irq_host *h, unsigned int virq, @@ -618,7 +618,7 @@ static void __init xics_setup_8259_cascade(void) unsigned long intack = 0; for_each_node_by_type(np, "interrupt-controller") - if (device_is_compatible(np, "chrp,iic")) { + if (of_device_is_compatible(np, "chrp,iic")) { found = np; break; } diff --git a/arch/powerpc/sysdev/dart_iommu.c b/arch/powerpc/sysdev/dart_iommu.c index 336186dd7f1..a1d2042bb30 100644 --- a/arch/powerpc/sysdev/dart_iommu.c +++ b/arch/powerpc/sysdev/dart_iommu.c @@ -36,6 +36,7 @@ #include <linux/pci.h> #include <linux/dma-mapping.h> #include <linux/vmalloc.h> +#include <linux/suspend.h> #include <asm/io.h> #include <asm/prom.h> #include <asm/iommu.h> @@ -54,6 +55,9 @@ static unsigned long dart_tablesize; /* Virtual base address of the DART table */ static u32 *dart_vbase; +#ifdef CONFIG_PM +static u32 *dart_copy; +#endif /* Mapped base address for the dart */ static unsigned int __iomem *dart; @@ -346,6 +350,48 @@ void iommu_init_early_dart(void) set_pci_dma_ops(&dma_direct_ops); } +#ifdef CONFIG_PM +static void iommu_dart_save(void) +{ + memcpy(dart_copy, dart_vbase, 2*1024*1024); +} + +static void iommu_dart_restore(void) +{ + memcpy(dart_vbase, dart_copy, 2*1024*1024); + dart_tlb_invalidate_all(); +} + +static int __init iommu_init_late_dart(void) +{ + unsigned long tbasepfn; + struct page *p; + + /* if no dart table exists then we won't need to save it + * and the area has also not been reserved */ + if (!dart_tablebase) + return 0; + + tbasepfn = __pa(dart_tablebase) >> PAGE_SHIFT; + register_nosave_region_late(tbasepfn, + tbasepfn + ((1<<24) >> PAGE_SHIFT)); + + /* For suspend we need to copy the dart contents because + * it is not part of the regular mapping (see above) and + * thus not saved automatically. The memory for this copy + * must be allocated early because we need 2 MB. */ + p = alloc_pages(GFP_KERNEL, 21 - PAGE_SHIFT); + BUG_ON(!p); + dart_copy = page_address(p); + + ppc_md.iommu_save = iommu_dart_save; + ppc_md.iommu_restore = iommu_dart_restore; + + return 0; +} + +late_initcall(iommu_init_late_dart); +#endif void __init alloc_dart_table(void) { diff --git a/arch/powerpc/sysdev/mpic.c b/arch/powerpc/sysdev/mpic.c index 0b84b7c775d..e88bbd5ec4c 100644 --- a/arch/powerpc/sysdev/mpic.c +++ b/arch/powerpc/sysdev/mpic.c @@ -354,6 +354,12 @@ static void mpic_startup_ht_interrupt(struct mpic *mpic, unsigned int source, tmp |= 0x22; writel(tmp, fixup->base + 4); spin_unlock_irqrestore(&mpic->fixup_lock, flags); + +#ifdef CONFIG_PM + /* use the lowest bit inverted to the actual HW, + * set if this fixup was enabled, clear otherwise */ + mpic->save_data[source].fixup_data = tmp | 1; +#endif } static void mpic_shutdown_ht_interrupt(struct mpic *mpic, unsigned int source, @@ -375,6 +381,12 @@ static void mpic_shutdown_ht_interrupt(struct mpic *mpic, unsigned int source, tmp |= 1; writel(tmp, fixup->base + 4); spin_unlock_irqrestore(&mpic->fixup_lock, flags); + +#ifdef CONFIG_PM + /* use the lowest bit inverted to the actual HW, + * set if this fixup was enabled, clear otherwise */ + mpic->save_data[source].fixup_data = tmp & ~1; +#endif } static void __init mpic_scan_ht_pic(struct mpic *mpic, u8 __iomem *devbase, @@ -1143,7 +1155,7 @@ void __init mpic_init(struct mpic *mpic) /* Do the HT PIC fixups on U3 broken mpic */ DBG("MPIC flags: %x\n", mpic->flags); if ((mpic->flags & MPIC_U3_HT_IRQS) && (mpic->flags & MPIC_PRIMARY)) - mpic_scan_ht_pics(mpic); + mpic_scan_ht_pics(mpic); for (i = 0; i < mpic->num_sources; i++) { /* start with vector = source number, and masked */ @@ -1167,6 +1179,12 @@ void __init mpic_init(struct mpic *mpic) /* Set current processor priority to 0 */ mpic_cpu_write(MPIC_INFO(CPU_CURRENT_TASK_PRI), 0); + +#ifdef CONFIG_PM + /* allocate memory to save mpic state */ + mpic->save_data = alloc_bootmem(mpic->num_sources * sizeof(struct mpic_irq_save)); + BUG_ON(mpic->save_data == NULL); +#endif } void __init mpic_set_clk_ratio(struct mpic *mpic, u32 clock_ratio) @@ -1333,8 +1351,11 @@ unsigned int mpic_get_one_irq(struct mpic *mpic) #ifdef DEBUG_LOW DBG("%s: get_one_irq(): %d\n", mpic->name, src); #endif - if (unlikely(src == mpic->spurious_vec)) + if (unlikely(src == mpic->spurious_vec)) { + if (mpic->flags & MPIC_SPV_EOI) + mpic_eoi(mpic); return NO_IRQ; + } return irq_linear_revmap(mpic->irqhost, src); } @@ -1417,3 +1438,79 @@ void __devinit smp_mpic_setup_cpu(int cpu) mpic_setup_this_cpu(); } #endif /* CONFIG_SMP */ + +#ifdef CONFIG_PM +static int mpic_suspend(struct sys_device *dev, pm_message_t state) +{ + struct mpic *mpic = container_of(dev, struct mpic, sysdev); + int i; + + for (i = 0; i < mpic->num_sources; i++) { + mpic->save_data[i].vecprio = + mpic_irq_read(i, MPIC_INFO(IRQ_VECTOR_PRI)); + mpic->save_data[i].dest = + mpic_irq_read(i, MPIC_INFO(IRQ_DESTINATION)); + } + + return 0; +} + +static int mpic_resume(struct sys_device *dev) +{ + struct mpic *mpic = container_of(dev, struct mpic, sysdev); + int i; + + for (i = 0; i < mpic->num_sources; i++) { + mpic_irq_write(i, MPIC_INFO(IRQ_VECTOR_PRI), + mpic->save_data[i].vecprio); + mpic_irq_write(i, MPIC_INFO(IRQ_DESTINATION), + mpic->save_data[i].dest); + +#ifdef CONFIG_MPIC_U3_HT_IRQS + { + struct mpic_irq_fixup *fixup = &mpic->fixups[i]; + + if (fixup->base) { + /* we use the lowest bit in an inverted meaning */ + if ((mpic->save_data[i].fixup_data & 1) == 0) + continue; + + /* Enable and configure */ + writeb(0x10 + 2 * fixup->index, fixup->base + 2); + + writel(mpic->save_data[i].fixup_data & ~1, + fixup->base + 4); + } + } +#endif + } /* end for loop */ + + return 0; +} +#endif + +static struct sysdev_class mpic_sysclass = { +#ifdef CONFIG_PM + .resume = mpic_resume, + .suspend = mpic_suspend, +#endif + set_kset_name("mpic"), +}; + +static int mpic_init_sys(void) +{ + struct mpic *mpic = mpics; + int error, id = 0; + + error = sysdev_class_register(&mpic_sysclass); + + while (mpic && !error) { + mpic->sysdev.cls = &mpic_sysclass; + mpic->sysdev.id = id++; + error = sysdev_register(&mpic->sysdev); + mpic = mpic->next; + } + return error; +} + +device_initcall(mpic_init_sys); diff --git a/arch/powerpc/sysdev/tsi108_dev.c b/arch/powerpc/sysdev/tsi108_dev.c index 337039ee51e..7d3b09b7d54 100644 --- a/arch/powerpc/sysdev/tsi108_dev.c +++ b/arch/powerpc/sysdev/tsi108_dev.c @@ -107,8 +107,9 @@ static int __init tsi108_eth_of_init(void) goto err; } - mac_addr = of_get_property(np, "address", NULL); - memcpy(tsi_eth_data.mac_addr, mac_addr, 6); + mac_addr = of_get_mac_address(np); + if (mac_addr) + memcpy(tsi_eth_data.mac_addr, mac_addr, 6); ph = of_get_property(np, "phy-handle", NULL); phy = of_find_node_by_phandle(*ph); @@ -129,6 +130,8 @@ static int __init tsi108_eth_of_init(void) tsi_eth_data.phyregs = res.start; tsi_eth_data.phy = *phy_id; tsi_eth_data.irq_num = irq_of_parse_and_map(np, 0); + if (of_device_is_compatible(phy, "bcm54xx")) + tsi_eth_data.phy_type = TSI108_PHY_BCM54XX; of_node_put(phy); ret = platform_device_add_data(tsi_eth_dev, &tsi_eth_data, diff --git a/arch/powerpc/sysdev/tsi108_pci.c b/arch/powerpc/sysdev/tsi108_pci.c index 58b9e7f8abf..2153163fa59 100644 --- a/arch/powerpc/sysdev/tsi108_pci.c +++ b/arch/powerpc/sysdev/tsi108_pci.c @@ -35,6 +35,7 @@ #include <asm/machdep.h> #include <asm/pci-bridge.h> #include <asm/tsi108.h> +#include <asm/tsi108_pci.h> #include <asm/tsi108_irq.h> #include <asm/prom.h> @@ -49,6 +50,7 @@ ((((bus)<<16) | ((devfunc)<<8) | (offset & 0xfc)) + tsi108_pci_cfg_base) u32 tsi108_pci_cfg_base; +static u32 tsi108_pci_cfg_phys; u32 tsi108_csr_vir_base; static struct device_node *pci_irq_node; static struct irq_host *pci_irq_host; @@ -185,7 +187,7 @@ tsi108_direct_read_config(struct pci_bus *bus, unsigned int devfn, int offset, void tsi108_clear_pci_cfg_error(void) { - tsi108_clear_pci_error(TSI108_PCI_CFG_BASE_PHYS); + tsi108_clear_pci_error(tsi108_pci_cfg_phys); } static struct pci_ops tsi108_direct_pci_ops = { @@ -193,17 +195,17 @@ static struct pci_ops tsi108_direct_pci_ops = { tsi108_direct_write_config }; -int __init tsi108_setup_pci(struct device_node *dev) +int __init tsi108_setup_pci(struct device_node *dev, u32 cfg_phys, int primary) { int len; struct pci_controller *hose; struct resource rsrc; const int *bus_range; - int primary = 0, has_address = 0; + int has_address = 0; /* PCI Config mapping */ - tsi108_pci_cfg_base = (u32)ioremap(TSI108_PCI_CFG_BASE_PHYS, - TSI108_PCI_CFG_SIZE); + tsi108_pci_cfg_base = (u32)ioremap(cfg_phys, TSI108_PCI_CFG_SIZE); + tsi108_pci_cfg_phys = cfg_phys; DBG("TSI_PCI: %s tsi108_pci_cfg_base=0x%x\n", __FUNCTION__, tsi108_pci_cfg_base); diff --git a/arch/powerpc/sysdev/uic.c b/arch/powerpc/sysdev/uic.c index 968fb40af9d..89059895a20 100644 --- a/arch/powerpc/sysdev/uic.c +++ b/arch/powerpc/sysdev/uic.c @@ -221,7 +221,7 @@ static struct uic * __init uic_init_one(struct device_node *node) const u32 *indexp, *dcrreg; int len; - BUG_ON(! device_is_compatible(node, "ibm,uic")); + BUG_ON(! of_device_is_compatible(node, "ibm,uic")); uic = alloc_bootmem(sizeof(*uic)); if (! uic) diff --git a/arch/ppc/syslib/ppc4xx_sgdma.c b/arch/ppc/syslib/ppc4xx_sgdma.c index 5dadca3e0d6..c4b369b50f9 100644 --- a/arch/ppc/syslib/ppc4xx_sgdma.c +++ b/arch/ppc/syslib/ppc4xx_sgdma.c @@ -23,10 +23,10 @@ #include <linux/mm.h> #include <linux/init.h> #include <linux/module.h> +#include <linux/dma-mapping.h> #include <asm/system.h> #include <asm/io.h> -#include <asm/dma-mapping.h> #include <asm/ppc4xx_dma.h> void diff --git a/drivers/ata/sata_svw.c b/drivers/ata/sata_svw.c index cc07aac10e8..17246734fe7 100644 --- a/drivers/ata/sata_svw.c +++ b/drivers/ata/sata_svw.c @@ -288,7 +288,7 @@ static int k2_sata_proc_info(struct Scsi_Host *shost, char *page, char **start, /* Match it to a port node */ index = (ap == ap->host->ports[0]) ? 0 : 1; for (np = np->child; np != NULL; np = np->sibling) { - const u32 *reg = get_property(np, "reg", NULL); + const u32 *reg = of_get_property(np, "reg", NULL); if (!reg) continue; if (index == *reg) diff --git a/drivers/char/agp/uninorth-agp.c b/drivers/char/agp/uninorth-agp.c index 91b062126a6..42c0a600b1a 100644 --- a/drivers/char/agp/uninorth-agp.c +++ b/drivers/char/agp/uninorth-agp.c @@ -613,7 +613,7 @@ static int __devinit agp_uninorth_probe(struct pci_dev *pdev, uninorth_node = of_find_node_by_name(NULL, "u3"); } if (uninorth_node) { - const int *revprop = get_property(uninorth_node, + const int *revprop = of_get_property(uninorth_node, "device-rev", NULL); if (revprop != NULL) uninorth_rev = *revprop & 0x3f; diff --git a/drivers/char/briq_panel.c b/drivers/char/briq_panel.c index c70d52ace8b..ed53f541d9e 100644 --- a/drivers/char/briq_panel.c +++ b/drivers/char/briq_panel.c @@ -206,7 +206,7 @@ static int __init briq_panel_init(void) const char *machine; int i; - machine = get_property(root, "model", NULL); + machine = of_get_property(root, "model", NULL); if (!machine || strncmp(machine, "TotalImpact,BRIQ-1", 18) != 0) { of_node_put(root); return -ENODEV; diff --git a/drivers/char/hvc_iseries.c b/drivers/char/hvc_iseries.c index ec420fe8a90..b37f1d5a5be 100644 --- a/drivers/char/hvc_iseries.c +++ b/drivers/char/hvc_iseries.c @@ -579,7 +579,7 @@ static int hvc_find_vtys(void) if (!vtermno) continue; - if (!device_is_compatible(vty, "IBM,iSeries-vty")) + if (!of_device_is_compatible(vty, "IBM,iSeries-vty")) continue; if (num_found == 0) diff --git a/drivers/char/hvc_vio.c b/drivers/char/hvc_vio.c index 94a542e20ef..79711aa4b41 100644 --- a/drivers/char/hvc_vio.c +++ b/drivers/char/hvc_vio.c @@ -157,7 +157,7 @@ static int hvc_find_vtys(void) if (!vtermno) continue; - if (device_is_compatible(vty, "hvterm1")) { + if (of_device_is_compatible(vty, "hvterm1")) { hvc_instantiate(*vtermno, num_found, &hvc_get_put_ops); ++num_found; } diff --git a/drivers/char/tpm/tpm_atmel.h b/drivers/char/tpm/tpm_atmel.h index 3c852009196..c912d8691cb 100644 --- a/drivers/char/tpm/tpm_atmel.h +++ b/drivers/char/tpm/tpm_atmel.h @@ -47,12 +47,12 @@ static void __iomem * atmel_get_base_addr(unsigned long *base, int *region_size) if (!dn) return NULL; - if (!device_is_compatible(dn, "AT97SC3201")) { + if (!of_device_is_compatible(dn, "AT97SC3201")) { of_node_put(dn); return NULL; } - reg = get_property(dn, "reg", ®len); + reg = of_get_property(dn, "reg", ®len); naddrc = of_n_addr_cells(dn); nsizec = of_n_size_cells(dn); diff --git a/drivers/hwmon/ams/ams-core.c b/drivers/hwmon/ams/ams-core.c index f5ebad56141..dbe6a32c064 100644 --- a/drivers/hwmon/ams/ams-core.c +++ b/drivers/hwmon/ams/ams-core.c @@ -144,7 +144,7 @@ int ams_sensor_attach(void) const u32 *prop; /* Get orientation */ - prop = get_property(ams_info.of_node, "orientation", NULL); + prop = of_get_property(ams_info.of_node, "orientation", NULL); if (!prop) return -ENODEV; ams_info.orient1 = *prop; @@ -208,14 +208,14 @@ int __init ams_init(void) #ifdef CONFIG_SENSORS_AMS_I2C np = of_find_node_by_name(NULL, "accelerometer"); - if (np && device_is_compatible(np, "AAPL,accelerometer_1")) + if (np && of_device_is_compatible(np, "AAPL,accelerometer_1")) /* Found I2C motion sensor */ return ams_i2c_init(np); #endif #ifdef CONFIG_SENSORS_AMS_PMU np = of_find_node_by_name(NULL, "sms"); - if (np && device_is_compatible(np, "sms")) + if (np && of_device_is_compatible(np, "sms")) /* Found PMU motion sensor */ return ams_pmu_init(np); #endif diff --git a/drivers/hwmon/ams/ams-i2c.c b/drivers/hwmon/ams/ams-i2c.c index 485d333bcb3..ccd5cefae90 100644 --- a/drivers/hwmon/ams/ams-i2c.c +++ b/drivers/hwmon/ams/ams-i2c.c @@ -276,7 +276,7 @@ int __init ams_i2c_init(struct device_node *np) ams_info.bustype = BUS_I2C; /* look for bus either using "reg" or by path */ - prop = get_property(ams_info.of_node, "reg", NULL); + prop = of_get_property(ams_info.of_node, "reg", NULL); if (!prop) { result = -ENODEV; diff --git a/drivers/hwmon/ams/ams-pmu.c b/drivers/hwmon/ams/ams-pmu.c index 1b01c215bfe..9463e9768f6 100644 --- a/drivers/hwmon/ams/ams-pmu.c +++ b/drivers/hwmon/ams/ams-pmu.c @@ -160,7 +160,7 @@ int __init ams_pmu_init(struct device_node *np) ams_info.bustype = BUS_HOST; /* Get PMU command, should be 0x4e, but we can never know */ - prop = get_property(ams_info.of_node, "reg", NULL); + prop = of_get_property(ams_info.of_node, "reg", NULL); if (!prop) { result = -ENODEV; goto exit; diff --git a/drivers/ide/pci/pdc202xx_new.c b/drivers/ide/pci/pdc202xx_new.c index 2da5cbb5356..2cdd629c653 100644 --- a/drivers/ide/pci/pdc202xx_new.c +++ b/drivers/ide/pci/pdc202xx_new.c @@ -395,7 +395,7 @@ static void __devinit apple_kiwi_init(struct pci_dev *pdev) unsigned int class_rev = 0; u8 conf; - if (np == NULL || !device_is_compatible(np, "kiwi-root")) + if (np == NULL || !of_device_is_compatible(np, "kiwi-root")) return; pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class_rev); diff --git a/drivers/ide/ppc/pmac.c b/drivers/ide/ppc/pmac.c index 071a030ec26..a49ebe44bab 100644 --- a/drivers/ide/ppc/pmac.c +++ b/drivers/ide/ppc/pmac.c @@ -1157,32 +1157,32 @@ pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif) pmif->cable_80 = 0; pmif->broken_dma = pmif->broken_dma_warn = 0; - if (device_is_compatible(np, "shasta-ata")) + if (of_device_is_compatible(np, "shasta-ata")) pmif->kind = controller_sh_ata6; - else if (device_is_compatible(np, "kauai-ata")) + else if (of_device_is_compatible(np, "kauai-ata")) pmif->kind = controller_un_ata6; - else if (device_is_compatible(np, "K2-UATA")) + else if (of_device_is_compatible(np, "K2-UATA")) pmif->kind = controller_k2_ata6; - else if (device_is_compatible(np, "keylargo-ata")) { + else if (of_device_is_compatible(np, "keylargo-ata")) { if (strcmp(np->name, "ata-4") == 0) pmif->kind = controller_kl_ata4; else pmif->kind = controller_kl_ata3; - } else if (device_is_compatible(np, "heathrow-ata")) + } else if (of_device_is_compatible(np, "heathrow-ata")) pmif->kind = controller_heathrow; else { pmif->kind = controller_ohare; pmif->broken_dma = 1; } - bidp = get_property(np, "AAPL,bus-id", NULL); + bidp = of_get_property(np, "AAPL,bus-id", NULL); pmif->aapl_bus_id = bidp ? *bidp : 0; /* Get cable type from device-tree */ if (pmif->kind == controller_kl_ata4 || pmif->kind == controller_un_ata6 || pmif->kind == controller_k2_ata6 || pmif->kind == controller_sh_ata6) { - const char* cable = get_property(np, "cable-type", NULL); + const char* cable = of_get_property(np, "cable-type", NULL); if (cable && !strncmp(cable, "80-", 3)) pmif->cable_80 = 1; } @@ -1190,8 +1190,8 @@ pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif) * they have a 80 conductor cable, this seem to be always the case unless * the user mucked around */ - if (device_is_compatible(np, "K2-UATA") || - device_is_compatible(np, "shasta-ata")) + if (of_device_is_compatible(np, "K2-UATA") || + of_device_is_compatible(np, "shasta-ata")) pmif->cable_80 = 1; /* On Kauai-type controllers, we make sure the FCR is correct */ diff --git a/drivers/infiniband/hw/ehca/ehca_main.c b/drivers/infiniband/hw/ehca/ehca_main.c index 2d370543e96..fe90e745456 100644 --- a/drivers/infiniband/hw/ehca/ehca_main.c +++ b/drivers/infiniband/hw/ehca/ehca_main.c @@ -570,7 +570,7 @@ static int __devinit ehca_probe(struct ibmebus_dev *dev, struct ib_pd *ibpd; int ret; - handle = get_property(dev->ofdev.node, "ibm,hca-handle", NULL); + handle = of_get_property(dev->ofdev.node, "ibm,hca-handle", NULL); if (!handle) { ehca_gen_err("Cannot get eHCA handle for adapter: %s.", dev->ofdev.node->full_name); diff --git a/drivers/macintosh/Kconfig b/drivers/macintosh/Kconfig index 1a86387e23b..a32c91e27b3 100644 --- a/drivers/macintosh/Kconfig +++ b/drivers/macintosh/Kconfig @@ -1,6 +1,10 @@ -menu "Macintosh device drivers" +menuconfig MACINTOSH_DRIVERS + bool "Macintosh device drivers" depends on PPC || MAC || X86 + default y + +if MACINTOSH_DRIVERS config ADB bool "Apple Desktop Bus (ADB) support" @@ -109,7 +113,9 @@ config PMAC_SMU config PMAC_APM_EMU tristate "APM emulation" - depends on PPC_PMAC && PPC32 && PM && ADB_PMU + select SYS_SUPPORTS_APM_EMULATION + select APM_EMULATION + depends on ADB_PMU && PM config PMAC_MEDIABAY bool "Support PowerBook hotswap media bay" @@ -234,4 +240,4 @@ config PMAC_RACKMETER This driver procides some support to control the front panel blue LEDs "vu-meter" of the XServer macs. -endmenu +endif # MACINTOSH_DRIVERS diff --git a/drivers/macintosh/apm_emu.c b/drivers/macintosh/apm_emu.c index cdb0bead991..9821e6361e6 100644 --- a/drivers/macintosh/apm_emu.c +++ b/drivers/macintosh/apm_emu.c @@ -1,9 +1,7 @@ -/* APM emulation layer for PowerMac - * - * Copyright 2001 Benjamin Herrenschmidt (benh@kernel.crashing.org) +/* + * APM emulation for PMU-based machines * - * Lots of code inherited from apm.c, see appropriate notice in - * arch/i386/kernel/apm.c + * Copyright 2001 Benjamin Herrenschmidt (benh@kernel.crashing.org) * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the @@ -18,429 +16,39 @@ * */ -#include <linux/module.h> - -#include <linux/poll.h> -#include <linux/types.h> -#include <linux/stddef.h> -#include <linux/timer.h> -#include <linux/fcntl.h> -#include <linux/slab.h> -#include <linux/stat.h> -#include <linux/proc_fs.h> -#include <linux/miscdevice.h> -#include <linux/apm_bios.h> -#include <linux/init.h> -#include <linux/sched.h> -#include <linux/pm.h> #include <linux/kernel.h> -#include <linux/smp_lock.h> - +#include <linux/module.h> +#include <linux/apm-emulation.h> #include <linux/adb.h> #include <linux/pmu.h> -#include <asm/system.h> -#include <asm/uaccess.h> -#include <asm/machdep.h> - -#undef DEBUG - -#ifdef DEBUG -#define DBG(args...) printk(KERN_DEBUG args) -//#define DBG(args...) xmon_printf(args) -#else -#define DBG(args...) do { } while (0) -#endif - -/* - * The apm_bios device is one of the misc char devices. - * This is its minor number. - */ -#define APM_MINOR_DEV 134 - -/* - * Maximum number of events stored - */ -#define APM_MAX_EVENTS 20 - -#define FAKE_APM_BIOS_VERSION 0x0101 - -#define APM_USER_NOTIFY_TIMEOUT (5*HZ) - -/* - * The per-file APM data - */ -struct apm_user { - int magic; - struct apm_user * next; - int suser: 1; - int suspend_waiting: 1; - int suspends_pending; - int suspends_read; - int event_head; - int event_tail; - apm_event_t events[APM_MAX_EVENTS]; -}; - -/* - * The magic number in apm_user - */ -#define APM_BIOS_MAGIC 0x4101 - -/* - * Local variables - */ -static int suspends_pending; - -static DECLARE_WAIT_QUEUE_HEAD(apm_waitqueue); -static DECLARE_WAIT_QUEUE_HEAD(apm_suspend_waitqueue); -static struct apm_user * user_list; - -static void apm_notify_sleep(struct pmu_sleep_notifier *self, int when); -static struct pmu_sleep_notifier apm_sleep_notifier = { - apm_notify_sleep, - SLEEP_LEVEL_USERLAND, -}; - -static const char driver_version[] = "0.5"; /* no spaces */ - -#ifdef DEBUG -static char * apm_event_name[] = { - "system standby", - "system suspend", - "normal resume", - "critical resume", - "low battery", - "power status change", - "update time", - "critical suspend", - "user standby", - "user suspend", - "system standby resume", - "capabilities change" -}; -#define NR_APM_EVENT_NAME \ - (sizeof(apm_event_name) / sizeof(apm_event_name[0])) - -#endif - -static int queue_empty(struct apm_user *as) -{ - return as->event_head == as->event_tail; -} - -static apm_event_t get_queued_event(struct apm_user *as) -{ - as->event_tail = (as->event_tail + 1) % APM_MAX_EVENTS; - return as->events[as->event_tail]; -} - -static void queue_event(apm_event_t event, struct apm_user *sender) -{ - struct apm_user * as; - - DBG("apm_emu: queue_event(%s)\n", apm_event_name[event-1]); - if (user_list == NULL) - return; - for (as = user_list; as != NULL; as = as->next) { - if (as == sender) - continue; - as->event_head = (as->event_head + 1) % APM_MAX_EVENTS; - if (as->event_head == as->event_tail) { - static int notified; - - if (notified++ == 0) - printk(KERN_ERR "apm_emu: an event queue overflowed\n"); - as->event_tail = (as->event_tail + 1) % APM_MAX_EVENTS; - } - as->events[as->event_head] = event; - if (!as->suser) - continue; - switch (event) { - case APM_SYS_SUSPEND: - case APM_USER_SUSPEND: - as->suspends_pending++; - suspends_pending++; - break; - case APM_NORMAL_RESUME: - as->suspend_waiting = 0; - break; - } - } - wake_up_interruptible(&apm_waitqueue); -} - -static int check_apm_user(struct apm_user *as, const char *func) -{ - if ((as == NULL) || (as->magic != APM_BIOS_MAGIC)) { - printk(KERN_ERR "apm_emu: %s passed bad filp\n", func); - return 1; - } - return 0; -} - -static ssize_t do_read(struct file *fp, char __user *buf, size_t count, loff_t *ppos) -{ - struct apm_user * as; - size_t i; - apm_event_t event; - DECLARE_WAITQUEUE(wait, current); - - as = fp->private_data; - if (check_apm_user(as, "read")) - return -EIO; - if (count < sizeof(apm_event_t)) - return -EINVAL; - if (queue_empty(as)) { - if (fp->f_flags & O_NONBLOCK) - return -EAGAIN; - add_wait_queue(&apm_waitqueue, &wait); -repeat: - set_current_state(TASK_INTERRUPTIBLE); - if (queue_empty(as) && !signal_pending(current)) { - schedule(); - goto repeat; - } - set_current_state(TASK_RUNNING); - remove_wait_queue(&apm_waitqueue, &wait); - } - i = count; - while ((i >= sizeof(event)) && !queue_empty(as)) { - event = get_queued_event(as); - DBG("apm_emu: do_read, returning: %s\n", apm_event_name[event-1]); - if (copy_to_user(buf, &event, sizeof(event))) { - if (i < count) - break; - return -EFAULT; - } - switch (event) { - case APM_SYS_SUSPEND: - case APM_USER_SUSPEND: - as->suspends_read++; - break; - } - buf += sizeof(event); - i -= sizeof(event); - } - if (i < count) - return count - i; - if (signal_pending(current)) - return -ERESTARTSYS; - return 0; -} - -static unsigned int do_poll(struct file *fp, poll_table * wait) -{ - struct apm_user * as; - - as = fp->private_data; - if (check_apm_user(as, "poll")) - return 0; - poll_wait(fp, &apm_waitqueue, wait); - if (!queue_empty(as)) - return POLLIN | POLLRDNORM; - return 0; -} - -static int do_ioctl(struct inode * inode, struct file *filp, - u_int cmd, u_long arg) -{ - struct apm_user * as; - DECLARE_WAITQUEUE(wait, current); - - as = filp->private_data; - if (check_apm_user(as, "ioctl")) - return -EIO; - if (!as->suser) - return -EPERM; - switch (cmd) { - case APM_IOC_SUSPEND: - /* If a suspend message was sent to userland, we - * consider this as a confirmation message - */ - if (as->suspends_read > 0) { - as->suspends_read--; - as->suspends_pending--; - suspends_pending--; - } else { - // Route to PMU suspend ? - break; - } - as->suspend_waiting = 1; - add_wait_queue(&apm_waitqueue, &wait); - DBG("apm_emu: ioctl waking up sleep waiter !\n"); - wake_up(&apm_suspend_waitqueue); - mb(); - while(as->suspend_waiting && !signal_pending(current)) { - set_current_state(TASK_INTERRUPTIBLE); - schedule(); - } - set_current_state(TASK_RUNNING); - remove_wait_queue(&apm_waitqueue, &wait); - break; - default: - return -EINVAL; - } - return 0; -} - -static int do_release(struct inode * inode, struct file * filp) -{ - struct apm_user * as; - - as = filp->private_data; - if (check_apm_user(as, "release")) - return 0; - filp->private_data = NULL; - lock_kernel(); - if (as->suspends_pending > 0) { - suspends_pending -= as->suspends_pending; - if (suspends_pending <= 0) - wake_up(&apm_suspend_waitqueue); - } - if (user_list == as) - user_list = as->next; - else { - struct apm_user * as1; - - for (as1 = user_list; - (as1 != NULL) && (as1->next != as); - as1 = as1->next) - ; - if (as1 == NULL) - printk(KERN_ERR "apm: filp not in user list\n"); - else - as1->next = as->next; - } - unlock_kernel(); - kfree(as); - return 0; -} - -static int do_open(struct inode * inode, struct file * filp) -{ - struct apm_user * as; - - as = kmalloc(sizeof(*as), GFP_KERNEL); - if (as == NULL) { - printk(KERN_ERR "apm: cannot allocate struct of size %d bytes\n", - sizeof(*as)); - return -ENOMEM; - } - as->magic = APM_BIOS_MAGIC; - as->event_tail = as->event_head = 0; - as->suspends_pending = 0; - as->suspends_read = 0; - /* - * XXX - this is a tiny bit broken, when we consider BSD - * process accounting. If the device is opened by root, we - * instantly flag that we used superuser privs. Who knows, - * we might close the device immediately without doing a - * privileged operation -- cevans - */ - as->suser = capable(CAP_SYS_ADMIN); - as->next = user_list; - user_list = as; - filp->private_data = as; - - DBG("apm_emu: opened by %s, suser: %d\n", current->comm, (int)as->suser); - - return 0; -} - -/* Wait for all clients to ack the suspend request. APM API - * doesn't provide a way to NAK, but this could be added - * here. - */ -static void wait_all_suspend(void) -{ - DECLARE_WAITQUEUE(wait, current); - - add_wait_queue(&apm_suspend_waitqueue, &wait); - DBG("apm_emu: wait_all_suspend(), suspends_pending: %d\n", suspends_pending); - while(suspends_pending > 0) { - set_current_state(TASK_UNINTERRUPTIBLE); - schedule(); - } - set_current_state(TASK_RUNNING); - remove_wait_queue(&apm_suspend_waitqueue, &wait); - - DBG("apm_emu: wait_all_suspend() - complete !\n"); -} - -static void apm_notify_sleep(struct pmu_sleep_notifier *self, int when) -{ - switch(when) { - case PBOOK_SLEEP_REQUEST: - queue_event(APM_SYS_SUSPEND, NULL); - wait_all_suspend(); - break; - case PBOOK_WAKE: - queue_event(APM_NORMAL_RESUME, NULL); - break; - } -} - #define APM_CRITICAL 10 #define APM_LOW 30 -static int apm_emu_get_info(char *buf, char **start, off_t fpos, int length) +static void pmu_apm_get_power_status(struct apm_power_info *info) { - /* Arguments, with symbols from linux/apm_bios.h. Information is - from the Get Power Status (0x0a) call unless otherwise noted. + int percentage = -1; + int batteries = 0; + int time_units = -1; + int real_count = 0; + int i; + char charging = 0; + long charge = -1; + long amperage = 0; + unsigned long btype = 0; + + info->battery_status = APM_BATTERY_STATUS_UNKNOWN; + info->battery_flag = APM_BATTERY_FLAG_UNKNOWN; + info->units = APM_UNITS_MINS; + + if (pmu_power_flags & PMU_PWR_AC_PRESENT) + info->ac_line_status = APM_AC_ONLINE; + else + info->ac_line_status = APM_AC_OFFLINE; - 0) Linux driver version (this will change if format changes) - 1) APM BIOS Version. Usually 1.0, 1.1 or 1.2. - 2) APM flags from APM Installation Check (0x00): - bit 0: APM_16_BIT_SUPPORT - bit 1: APM_32_BIT_SUPPORT - bit 2: APM_IDLE_SLOWS_CLOCK - bit 3: APM_BIOS_DISABLED - bit 4: APM_BIOS_DISENGAGED - 3) AC line status - 0x00: Off-line - 0x01: On-line - 0x02: On backup power (BIOS >= 1.1 only) - 0xff: Unknown - 4) Battery status - 0x00: High - 0x01: Low - 0x02: Critical - 0x03: Charging - 0x04: Selected battery not present (BIOS >= 1.2 only) - 0xff: Unknown - 5) Battery flag - bit 0: High - bit 1: Low - bit 2: Critical - bit 3: Charging - bit 7: No system battery - 0xff: Unknown - 6) Remaining battery life (percentage of charge): - 0-100: valid - -1: Unknown - 7) Remaining battery life (time units): - Number of remaining minutes or seconds - -1: Unknown - 8) min = minutes; sec = seconds */ - - unsigned short ac_line_status; - unsigned short battery_status = 0; - unsigned short battery_flag = 0xff; - int percentage = -1; - int time_units = -1; - int real_count = 0; - int i; - char * p = buf; - char charging = 0; - long charge = -1; - long amperage = 0; - unsigned long btype = 0; - - ac_line_status = ((pmu_power_flags & PMU_PWR_AC_PRESENT) != 0); for (i=0; i<pmu_battery_count; i++) { if (pmu_batteries[i].flags & PMU_BATT_PRESENT) { - battery_status++; + batteries++; if (percentage < 0) percentage = 0; if (charge < 0) @@ -456,9 +64,9 @@ static int apm_emu_get_info(char *buf, char **start, off_t fpos, int length) charging++; } } - if (0 == battery_status) - ac_line_status = 1; - battery_status = 0xff; + if (batteries == 0) + info->ac_line_status = APM_AC_ONLINE; + if (real_count) { if (amperage < 0) { if (btype == PMU_BATT_TYPE_SMART) @@ -468,85 +76,44 @@ static int apm_emu_get_info(char *buf, char **start, off_t fpos, int length) } percentage /= real_count; if (charging > 0) { - battery_status = 0x03; - battery_flag = 0x08; + info->battery_status = APM_BATTERY_STATUS_CHARGING; + info->battery_flag = APM_BATTERY_FLAG_CHARGING; } else if (percentage <= APM_CRITICAL) { - battery_status = 0x02; - battery_flag = 0x04; + info->battery_status = APM_BATTERY_STATUS_CRITICAL; + info->battery_flag = APM_BATTERY_FLAG_CRITICAL; } else if (percentage <= APM_LOW) { - battery_status = 0x01; - battery_flag = 0x02; + info->battery_status = APM_BATTERY_STATUS_LOW; + info->battery_flag = APM_BATTERY_FLAG_LOW; } else { - battery_status = 0x00; - battery_flag = 0x01; + info->battery_status = APM_BATTERY_STATUS_HIGH; + info->battery_flag = APM_BATTERY_FLAG_HIGH; } } - p += sprintf(p, "%s %d.%d 0x%02x 0x%02x 0x%02x 0x%02x %d%% %d %s\n", - driver_version, - (FAKE_APM_BIOS_VERSION >> 8) & 0xff, - FAKE_APM_BIOS_VERSION & 0xff, - 0, - ac_line_status, - battery_status, - battery_flag, - percentage, - time_units, - "min"); - return p - buf; + info->battery_life = percentage; + info->time = time_units; } -static const struct file_operations apm_bios_fops = { - .owner = THIS_MODULE, - .read = do_read, - .poll = do_poll, - .ioctl = do_ioctl, - .open = do_open, - .release = do_release, -}; - -static struct miscdevice apm_device = { - APM_MINOR_DEV, - "apm_bios", - &apm_bios_fops -}; - static int __init apm_emu_init(void) { - struct proc_dir_entry *apm_proc; - - if (sys_ctrler != SYS_CTRLER_PMU) { - printk(KERN_INFO "apm_emu: Requires a machine with a PMU.\n"); - return -ENODEV; - } - - apm_proc = create_proc_info_entry("apm", 0, NULL, apm_emu_get_info); - if (apm_proc) - apm_proc->owner = THIS_MODULE; + apm_get_power_status = pmu_apm_get_power_status; - if (misc_register(&apm_device) != 0) - printk(KERN_INFO "Could not create misc. device for apm\n"); - - pmu_register_sleep_notifier(&apm_sleep_notifier); - - printk(KERN_INFO "apm_emu: APM Emulation %s initialized.\n", driver_version); + printk(KERN_INFO "apm_emu: PMU APM Emulation initialized.\n"); return 0; } static void __exit apm_emu_exit(void) { - pmu_unregister_sleep_notifier(&apm_sleep_notifier); - misc_deregister(&apm_device); - remove_proc_entry("apm", NULL); + if (apm_get_power_status == pmu_apm_get_power_status) + apm_get_power_status = NULL; - printk(KERN_INFO "apm_emu: APM Emulation removed.\n"); + printk(KERN_INFO "apm_emu: PMU APM Emulation removed.\n"); } module_init(apm_emu_init); module_exit(apm_emu_exit); MODULE_AUTHOR("Benjamin Herrenschmidt"); -MODULE_DESCRIPTION("APM emulation layer for PowerMac"); +MODULE_DESCRIPTION("APM emulation for PowerMac"); MODULE_LICENSE("GPL"); - diff --git a/drivers/macintosh/mac_hid.c b/drivers/macintosh/mac_hid.c index 1599dc34f15..76c1e8e4a48 100644 --- a/drivers/macintosh/mac_hid.c +++ b/drivers/macintosh/mac_hid.c @@ -24,7 +24,7 @@ static int mouse_last_keycode; #if defined(CONFIG_SYSCTL) /* file(s) in /proc/sys/dev/mac_hid */ -ctl_table mac_hid_files[] = { +static ctl_table mac_hid_files[] = { { .ctl_name = DEV_MAC_HID_MOUSE_BUTTON_EMULATION, .procname = "mouse_button_emulation", @@ -53,7 +53,7 @@ ctl_table mac_hid_files[] = { }; /* dir in /proc/sys/dev */ -ctl_table mac_hid_dir[] = { +static ctl_table mac_hid_dir[] = { { .ctl_name = DEV_MAC_HID, .procname = "mac_hid", @@ -65,7 +65,7 @@ ctl_table mac_hid_dir[] = { }; /* /proc/sys/dev itself, in case that is not there yet */ -ctl_table mac_hid_root_dir[] = { +static ctl_table mac_hid_root_dir[] = { { .ctl_name = CTL_DEV, .procname = "dev", @@ -127,7 +127,7 @@ static int emumousebtn_input_register(void) return ret; } -int __init mac_hid_init(void) +static int __init mac_hid_init(void) { int err; diff --git a/drivers/macintosh/macio_sysfs.c b/drivers/macintosh/macio_sysfs.c index cc826791265..112e5ef728f 100644 --- a/drivers/macintosh/macio_sysfs.c +++ b/drivers/macintosh/macio_sysfs.c @@ -41,28 +41,15 @@ compatible_show (struct device *dev, struct device_attribute *attr, char *buf) static ssize_t modalias_show (struct device *dev, struct device_attribute *attr, char *buf) { - struct of_device *of; - const char *compat; - int cplen; - int length; + struct of_device *ofdev = to_of_device(dev); + int len; - of = &to_macio_device (dev)->ofdev; - compat = of_get_property(of->node, "compatible", &cplen); - if (!compat) compat = "", cplen = 1; - length = sprintf (buf, "of:N%sT%s", of->node->name, of->node->type); - buf += length; - while (cplen > 0) { - int l; - l = sprintf (buf, "C%s", compat); - length += l; - buf += l; - l = strlen (compat) + 1; - compat += l; - cplen -= l; - } - length += sprintf(buf, "\n"); + len = of_device_get_modalias(ofdev, buf, PAGE_SIZE); - return length; + buf[len] = '\n'; + buf[len+1] = 0; + + return len+1; } macio_config_of_attr (name, "%s\n"); diff --git a/drivers/macintosh/smu.c b/drivers/macintosh/smu.c index a98a328b1cf..f8e1a135bf9 100644 --- a/drivers/macintosh/smu.c +++ b/drivers/macintosh/smu.c @@ -606,7 +606,7 @@ static void smu_expose_childs(struct work_struct *unused) struct device_node *np; for (np = NULL; (np = of_get_next_child(smu->of_node, np)) != NULL;) - if (device_is_compatible(np, "smu-sensors")) + if (of_device_is_compatible(np, "smu-sensors")) of_platform_device_create(np, "smu-sensors", &smu->of_dev->dev); } diff --git a/drivers/macintosh/therm_adt746x.c b/drivers/macintosh/therm_adt746x.c index 228903403cf..178afa1fd56 100644 --- a/drivers/macintosh/therm_adt746x.c +++ b/drivers/macintosh/therm_adt746x.c @@ -560,9 +560,9 @@ thermostat_init(void) np = of_find_node_by_name(NULL, "fan"); if (!np) return -ENODEV; - if (device_is_compatible(np, "adt7460")) + if (of_device_is_compatible(np, "adt7460")) therm_type = ADT7460; - else if (device_is_compatible(np, "adt7467")) + else if (of_device_is_compatible(np, "adt7467")) therm_type = ADT7467; else return -ENODEV; diff --git a/drivers/macintosh/via-pmu-led.c b/drivers/macintosh/via-pmu-led.c index fc89a7047cd..55ad9567138 100644 --- a/drivers/macintosh/via-pmu-led.c +++ b/drivers/macintosh/via-pmu-led.c @@ -31,7 +31,6 @@ static spinlock_t pmu_blink_lock; static struct adb_request pmu_blink_req; /* -1: no change, 0: request off, 1: request on */ static int requested_change; -static int sleeping; static void pmu_req_done(struct adb_request * req) { @@ -41,7 +40,7 @@ static void pmu_req_done(struct adb_request * req) /* if someone requested a change in the meantime * (we only see the last one which is fine) * then apply it now */ - if (requested_change != -1 && !sleeping) + if (requested_change != -1 && !pmu_sys_suspended) pmu_request(&pmu_blink_req, NULL, 4, 0xee, 4, 0, requested_change); /* reset requested change */ requested_change = -1; @@ -66,7 +65,7 @@ static void pmu_led_set(struct led_classdev *led_cdev, break; } /* if request isn't done, then don't do anything */ - if (pmu_blink_req.complete && !sleeping) + if (pmu_blink_req.complete && !pmu_sys_suspended) pmu_request(&pmu_blink_req, NULL, 4, 0xee, 4, 0, requested_change); out: spin_unlock_irqrestore(&pmu_blink_lock, flags); @@ -80,32 +79,6 @@ static struct led_classdev pmu_led = { .brightness_set = pmu_led_set, }; -#ifdef CONFIG_PM -static void pmu_led_sleep_call(struct pmu_sleep_notifier *self, int when) -{ - unsigned long flags; - - spin_lock_irqsave(&pmu_blink_lock, flags); - - switch (when) { - case PBOOK_SLEEP_REQUEST: - sleeping = 1; - break; - case PBOOK_WAKE: - sleeping = 0; - break; - default: - /* do nothing */ - break; - } - spin_unlock_irqrestore(&pmu_blink_lock, flags); -} - -static struct pmu_sleep_notifier via_pmu_led_sleep_notif = { - .notifier_call = pmu_led_sleep_call, -}; -#endif - static int __init via_pmu_led_init(void) { struct device_node *dt; @@ -135,9 +108,7 @@ static int __init via_pmu_led_init(void) /* no outstanding req */ pmu_blink_req.complete = 1; pmu_blink_req.done = pmu_req_done; -#ifdef CONFIG_PM - pmu_register_sleep_notifier(&via_pmu_led_sleep_notif); -#endif + return led_classdev_register(NULL, &pmu_led); } diff --git a/drivers/macintosh/via-pmu.c b/drivers/macintosh/via-pmu.c index 1729d3fd7a1..157080b3b46 100644 --- a/drivers/macintosh/via-pmu.c +++ b/drivers/macintosh/via-pmu.c @@ -310,14 +310,14 @@ int __init find_via_pmu(void) PMU_INT_TICK; if (vias->parent->name && ((strcmp(vias->parent->name, "ohare") == 0) - || device_is_compatible(vias->parent, "ohare"))) + || of_device_is_compatible(vias->parent, "ohare"))) pmu_kind = PMU_OHARE_BASED; - else if (device_is_compatible(vias->parent, "paddington")) + else if (of_device_is_compatible(vias->parent, "paddington")) pmu_kind = PMU_PADDINGTON_BASED; - else if (device_is_compatible(vias->parent, "heathrow")) + else if (of_device_is_compatible(vias->parent, "heathrow")) pmu_kind = PMU_HEATHROW_BASED; - else if (device_is_compatible(vias->parent, "Keylargo") - || device_is_compatible(vias->parent, "K2-Keylargo")) { + else if (of_device_is_compatible(vias->parent, "Keylargo") + || of_device_is_compatible(vias->parent, "K2-Keylargo")) { struct device_node *gpiop; struct device_node *adbp; u64 gaddr = OF_BAD_ADDR; @@ -2759,7 +2759,7 @@ pmu_polled_request(struct adb_request *req) #if defined(CONFIG_PM) && defined(CONFIG_PPC32) -static int pmu_sys_suspended; +int pmu_sys_suspended; static int pmu_sys_suspend(struct sys_device *sysdev, pm_message_t state) { diff --git a/drivers/macintosh/windfarm_lm75_sensor.c b/drivers/macintosh/windfarm_lm75_sensor.c index ab4d1b63f63..a0fabf3c200 100644 --- a/drivers/macintosh/windfarm_lm75_sensor.c +++ b/drivers/macintosh/windfarm_lm75_sensor.c @@ -188,10 +188,10 @@ static int wf_lm75_attach(struct i2c_adapter *adapter) if (loc == NULL || addr == 0) continue; /* real lm75 */ - if (device_is_compatible(dev, "lm75")) + if (of_device_is_compatible(dev, "lm75")) wf_lm75_create(adapter, addr, 0, loc); /* ds1775 (compatible, better resolution */ - else if (device_is_compatible(dev, "ds1775")) + else if (of_device_is_compatible(dev, "ds1775")) wf_lm75_create(adapter, addr, 1, loc); } return 0; diff --git a/drivers/macintosh/windfarm_max6690_sensor.c b/drivers/macintosh/windfarm_max6690_sensor.c index eaa74afa175..5f03aab9fb5 100644 --- a/drivers/macintosh/windfarm_max6690_sensor.c +++ b/drivers/macintosh/windfarm_max6690_sensor.c @@ -131,7 +131,7 @@ static int wf_max6690_attach(struct i2c_adapter *adapter) */ if (!pmac_i2c_match_adapter(dev, adapter)) continue; - if (!device_is_compatible(dev, "max6690")) + if (!of_device_is_compatible(dev, "max6690")) continue; addr = pmac_i2c_get_dev_addr(dev); loc = of_get_property(dev, "hwsensor-location", NULL); diff --git a/drivers/macintosh/windfarm_smu_controls.c b/drivers/macintosh/windfarm_smu_controls.c index ff398adc028..58c2590f05e 100644 --- a/drivers/macintosh/windfarm_smu_controls.c +++ b/drivers/macintosh/windfarm_smu_controls.c @@ -263,7 +263,7 @@ static int __init smu_controls_init(void) /* Look for RPM fans */ for (fans = NULL; (fans = of_get_next_child(smu, fans)) != NULL;) if (!strcmp(fans->name, "rpm-fans") || - device_is_compatible(fans, "smu-rpm-fans")) + of_device_is_compatible(fans, "smu-rpm-fans")) break; for (fan = NULL; fans && (fan = of_get_next_child(fans, fan)) != NULL;) { diff --git a/drivers/macintosh/windfarm_smu_sat.c b/drivers/macintosh/windfarm_smu_sat.c index 9a6c2cf8fd0..1043b39aa12 100644 --- a/drivers/macintosh/windfarm_smu_sat.c +++ b/drivers/macintosh/windfarm_smu_sat.c @@ -380,7 +380,7 @@ static int wf_sat_attach(struct i2c_adapter *adapter) busnode = pmac_i2c_get_bus_node(bus); while ((dev = of_get_next_child(busnode, dev)) != NULL) - if (device_is_compatible(dev, "smu-sat")) + if (of_device_is_compatible(dev, "smu-sat")) wf_sat_create(adapter, dev); return 0; } diff --git a/drivers/mtd/maps/physmap_of.c b/drivers/mtd/maps/physmap_of.c index 7efe744ad31..72107dc06d6 100644 --- a/drivers/mtd/maps/physmap_of.c +++ b/drivers/mtd/maps/physmap_of.c @@ -48,7 +48,7 @@ static int parse_flash_partitions(struct device_node *node, const u32 *part; const char *name; - part = get_property(node, "partitions", &plen); + part = of_get_property(node, "partitions", &plen); if (part == NULL) goto err; @@ -59,7 +59,7 @@ static int parse_flash_partitions(struct device_node *node, goto err; } - name = get_property(node, "partition-names", &plen); + name = of_get_property(node, "partition-names", &plen); for (i = 0; i < retval; i++) { (*parts)[i].offset = *part++; @@ -153,7 +153,7 @@ static int __devinit of_physmap_probe(struct of_device *dev, const struct of_dev goto err_out; } - width = get_property(dp, "bank-width", NULL); + width = of_get_property(dp, "bank-width", NULL); if (width == NULL) { dev_err(&dev->dev, "Can't get the flash bank width!\n"); err = -EINVAL; @@ -174,7 +174,7 @@ static int __devinit of_physmap_probe(struct of_device *dev, const struct of_dev simple_map_init(&info->map); - of_probe = get_property(dp, "probe-type", NULL); + of_probe = of_get_property(dp, "probe-type", NULL); if (of_probe == NULL) { probe_type = rom_probe_types; for (; info->mtd == NULL && *probe_type != NULL; probe_type++) diff --git a/drivers/net/bmac.c b/drivers/net/bmac.c index 4612725965d..9b8d7d9dbe8 100644 --- a/drivers/net/bmac.c +++ b/drivers/net/bmac.c @@ -1260,9 +1260,10 @@ static int __devinit bmac_probe(struct macio_dev *mdev, const struct of_device_i printk(KERN_ERR "BMAC: can't use, need 3 addrs and 3 intrs\n"); return -ENODEV; } - prop_addr = get_property(macio_get_of_node(mdev), "mac-address", NULL); + prop_addr = of_get_property(macio_get_of_node(mdev), + "mac-address", NULL); if (prop_addr == NULL) { - prop_addr = get_property(macio_get_of_node(mdev), + prop_addr = of_get_property(macio_get_of_node(mdev), "local-mac-address", NULL); if (prop_addr == NULL) { printk(KERN_ERR "BMAC: Can't get mac-address\n"); diff --git a/drivers/net/ehea/ehea_main.c b/drivers/net/ehea/ehea_main.c index c7a5614e66c..a1bd2d861d9 100644 --- a/drivers/net/ehea/ehea_main.c +++ b/drivers/net/ehea/ehea_main.c @@ -2603,14 +2603,13 @@ static int ehea_setup_ports(struct ehea_adapter *adapter) { struct device_node *lhea_dn; struct device_node *eth_dn = NULL; - - u32 *dn_log_port_id; + const u32 *dn_log_port_id; int i = 0; lhea_dn = adapter->ebus_dev->ofdev.node; while ((eth_dn = of_get_next_child(lhea_dn, eth_dn))) { - dn_log_port_id = (u32*)get_property(eth_dn, "ibm,hea-port-no", + dn_log_port_id = of_get_property(eth_dn, "ibm,hea-port-no", NULL); if (!dn_log_port_id) { ehea_error("bad device node: eth_dn name=%s", @@ -2645,12 +2644,12 @@ static struct device_node *ehea_get_eth_dn(struct ehea_adapter *adapter, { struct device_node *lhea_dn; struct device_node *eth_dn = NULL; - u32 *dn_log_port_id; + const u32 *dn_log_port_id; lhea_dn = adapter->ebus_dev->ofdev.node; while ((eth_dn = of_get_next_child(lhea_dn, eth_dn))) { - dn_log_port_id = (u32*)get_property(eth_dn, "ibm,hea-port-no", + dn_log_port_id = of_get_property(eth_dn, "ibm,hea-port-no", NULL); if (dn_log_port_id) if (*dn_log_port_id == logical_port_id) @@ -2774,7 +2773,7 @@ static int __devinit ehea_probe_adapter(struct ibmebus_dev *dev, const struct of_device_id *id) { struct ehea_adapter *adapter; - u64 *adapter_handle; + const u64 *adapter_handle; int ret; if (!dev || !dev->ofdev.node) { @@ -2791,7 +2790,7 @@ static int __devinit ehea_probe_adapter(struct ibmebus_dev *dev, adapter->ebus_dev = dev; - adapter_handle = (u64*)get_property(dev->ofdev.node, "ibm,hea-handle", + adapter_handle = of_get_property(dev->ofdev.node, "ibm,hea-handle", NULL); if (adapter_handle) adapter->handle = *adapter_handle; diff --git a/drivers/net/mace.c b/drivers/net/mace.c index b3bd6239495..52b9332810c 100644 --- a/drivers/net/mace.c +++ b/drivers/net/mace.c @@ -110,9 +110,9 @@ static int __devinit mace_probe(struct macio_dev *mdev, const struct of_device_i return -ENODEV; } - addr = get_property(mace, "mac-address", NULL); + addr = of_get_property(mace, "mac-address", NULL); if (addr == NULL) { - addr = get_property(mace, "local-mac-address", NULL); + addr = of_get_property(mace, "local-mac-address", NULL); if (addr == NULL) { printk(KERN_ERR "Can't get mac-address for MACE %s\n", mace->full_name); diff --git a/drivers/net/pasemi_mac.c b/drivers/net/pasemi_mac.c index 76fe9dd8e84..07eb9b24a97 100644 --- a/drivers/net/pasemi_mac.c +++ b/drivers/net/pasemi_mac.c @@ -80,7 +80,7 @@ static int pasemi_get_mac_addr(struct pasemi_mac *mac) return -ENOENT; } - maddr = get_property(dn, "mac-address", NULL); + maddr = of_get_property(dn, "mac-address", NULL); if (maddr == NULL) { dev_warn(&pdev->dev, "no mac address in device tree, not configuring\n"); diff --git a/drivers/net/spider_net.c b/drivers/net/spider_net.c index 230da14b1b6..c15e97253ed 100644 --- a/drivers/net/spider_net.c +++ b/drivers/net/spider_net.c @@ -1830,7 +1830,7 @@ try_host_fw: if (!dn) goto out_err; - fw_prop = get_property(dn, "firmware", &fw_size); + fw_prop = of_get_property(dn, "firmware", &fw_size); if (!fw_prop) goto out_err; @@ -2236,7 +2236,7 @@ spider_net_setup_netdev(struct spider_net_card *card) if (!dn) return -EIO; - mac = get_property(dn, "local-mac-address", NULL); + mac = of_get_property(dn, "local-mac-address", NULL); if (!mac) return -EIO; memcpy(addr.sa_data, mac, ETH_ALEN); diff --git a/drivers/net/sungem.c b/drivers/net/sungem.c index 5da73212ac9..43280385503 100644 --- a/drivers/net/sungem.c +++ b/drivers/net/sungem.c @@ -2903,7 +2903,7 @@ static int __devinit gem_get_device_address(struct gem *gp) struct net_device *dev = gp->dev; const unsigned char *addr; - addr = get_property(gp->of_node, "local-mac-address", NULL); + addr = of_get_property(gp->of_node, "local-mac-address", NULL); if (addr == NULL) { #ifdef CONFIG_SPARC addr = idprom->id_ethaddr; diff --git a/drivers/net/sungem_phy.c b/drivers/net/sungem_phy.c index 56a110ca5e6..61843fd5752 100644 --- a/drivers/net/sungem_phy.c +++ b/drivers/net/sungem_phy.c @@ -451,7 +451,7 @@ static int bcm5421_init(struct mii_phy* phy) if (phy->platform_data) { struct device_node *np = of_get_parent(phy->platform_data); int can_low_power = 1; - if (np == NULL || get_property(np, "no-autolowpower", NULL)) + if (np == NULL || of_get_property(np, "no-autolowpower", NULL)) can_low_power = 0; if (can_low_power) { /* Enable automatic low-power */ diff --git a/drivers/net/tsi108_eth.c b/drivers/net/tsi108_eth.c index 0bfc2c9c1c0..1aabc91f645 100644 --- a/drivers/net/tsi108_eth.c +++ b/drivers/net/tsi108_eth.c @@ -82,6 +82,7 @@ struct tsi108_prv_data { unsigned int phy; /* Index of PHY for this interface */ unsigned int irq_num; unsigned int id; + unsigned int phy_type; struct timer_list timer;/* Timer that triggers the check phy function */ unsigned int rxtail; /* Next entry in rxring to read */ @@ -1256,11 +1257,11 @@ static void tsi108_init_phy(struct net_device *dev) if (i == 0) printk(KERN_ERR "%s function time out \n", __FUNCTION__); -#if (TSI108_PHY_TYPE == PHY_BCM54XX) /* Broadcom BCM54xx PHY */ - tsi108_write_mii(data, 0x09, 0x0300); - tsi108_write_mii(data, 0x10, 0x1020); - tsi108_write_mii(data, 0x1c, 0x8c00); -#endif + if (data->phy_type == TSI108_PHY_BCM54XX) { + tsi108_write_mii(data, 0x09, 0x0300); + tsi108_write_mii(data, 0x10, 0x1020); + tsi108_write_mii(data, 0x1c, 0x8c00); + } tsi108_write_mii(data, MII_BMCR, @@ -1587,6 +1588,7 @@ tsi108_init_one(struct platform_device *pdev) data->mii_if.supports_gmii = mii_check_gmii_support(&data->mii_if); data->phy = einfo->phy; + data->phy_type = einfo->phy_type; data->irq_num = einfo->irq_num; data->id = pdev->id; dev->open = tsi108_open; diff --git a/drivers/net/tsi108_eth.h b/drivers/net/tsi108_eth.h index 77a769df228..5a77ae6c5f3 100644 --- a/drivers/net/tsi108_eth.h +++ b/drivers/net/tsi108_eth.h @@ -43,15 +43,6 @@ in_be32((data->phyregs + (offset))) /* - * PHY Configuration Options - * - * NOTE: Enable set of definitions corresponding to your board type - */ -#define PHY_MV88E 1 /* Marvel 88Exxxx PHY */ -#define PHY_BCM54XX 2 /* Broardcom BCM54xx PHY */ -#define TSI108_PHY_TYPE PHY_MV88E - -/* * TSI108 GIGE port registers */ diff --git a/drivers/net/ucc_geth.c b/drivers/net/ucc_geth.c index 16b9acdabbe..d7aff818937 100644 --- a/drivers/net/ucc_geth.c +++ b/drivers/net/ucc_geth.c @@ -3787,7 +3787,7 @@ static int ucc_geth_probe(struct of_device* ofdev, const struct of_device_id *ma ugeth_vdbg("%s: IN", __FUNCTION__); - prop = get_property(np, "device-id", NULL); + prop = of_get_property(np, "device-id", NULL); ucc_num = *prop - 1; if ((ucc_num < 0) || (ucc_num > 7)) return -ENODEV; @@ -3795,9 +3795,9 @@ static int ucc_geth_probe(struct of_device* ofdev, const struct of_device_id *ma ug_info = &ugeth_info[ucc_num]; ug_info->uf_info.ucc_num = ucc_num; - prop = get_property(np, "rx-clock", NULL); + prop = of_get_property(np, "rx-clock", NULL); ug_info->uf_info.rx_clock = *prop; - prop = get_property(np, "tx-clock", NULL); + prop = of_get_property(np, "tx-clock", NULL); ug_info->uf_info.tx_clock = *prop; err = of_address_to_resource(np, 0, &res); if (err) @@ -3806,23 +3806,23 @@ static int ucc_geth_probe(struct of_device* ofdev, const struct of_device_id *ma ug_info->uf_info.regs = res.start; ug_info->uf_info.irq = irq_of_parse_and_map(np, 0); - ph = get_property(np, "phy-handle", NULL); + ph = of_get_property(np, "phy-handle", NULL); phy = of_find_node_by_phandle(*ph); if (phy == NULL) return -ENODEV; /* set the PHY address */ - prop = get_property(phy, "reg", NULL); + prop = of_get_property(phy, "reg", NULL); if (prop == NULL) return -1; ug_info->phy_address = *prop; /* get the phy interface type, or default to MII */ - prop = get_property(np, "interface-type", NULL); + prop = of_get_property(np, "interface-type", NULL); if (!prop) { /* handle interface property present in old trees */ - prop = get_property(phy, "interface", NULL); + prop = of_get_property(phy, "interface", NULL); if (prop != NULL) phy_interface = enet_to_phy_interface[*prop]; else @@ -3832,10 +3832,10 @@ static int ucc_geth_probe(struct of_device* ofdev, const struct of_device_id *ma } /* get speed, or derive from interface */ - prop = get_property(np, "max-speed", NULL); + prop = of_get_property(np, "max-speed", NULL); if (!prop) { /* handle interface property present in old trees */ - prop = get_property(phy, "interface", NULL); + prop = of_get_property(phy, "interface", NULL); if (prop != NULL) max_speed = enet_to_speed[*prop]; } else { diff --git a/drivers/net/ucc_geth_mii.c b/drivers/net/ucc_geth_mii.c index 73b5a538e8f..27a1ef3b7b0 100644 --- a/drivers/net/ucc_geth_mii.c +++ b/drivers/net/ucc_geth_mii.c @@ -172,7 +172,7 @@ static int uec_mdio_probe(struct of_device *ofdev, const struct of_device_id *ma while ((child = of_get_next_child(np, child)) != NULL) { int irq = irq_of_parse_and_map(child, 0); if (irq != NO_IRQ) { - const u32 *id = get_property(child, "reg", NULL); + const u32 *id = of_get_property(child, "reg", NULL); new_bus->irq[*id] = irq; } } @@ -203,7 +203,7 @@ static int uec_mdio_probe(struct of_device *ofdev, const struct of_device_id *ma if ((res.start >= tempres.start) && (res.end <= tempres.end)) { /* set this UCC to be the MII master */ - const u32 *id = get_property(tempnp, "device-id", NULL); + const u32 *id = of_get_property(tempnp, "device-id", NULL); if (id == NULL) goto bus_register_fail; diff --git a/drivers/pci/hotplug/rpaphp_core.c b/drivers/pci/hotplug/rpaphp_core.c index 847936fe327..899eed00274 100644 --- a/drivers/pci/hotplug/rpaphp_core.c +++ b/drivers/pci/hotplug/rpaphp_core.c @@ -170,10 +170,10 @@ static int get_children_props(struct device_node *dn, const int **drc_indexes, { const int *indexes, *names, *types, *domains; - indexes = get_property(dn, "ibm,drc-indexes", NULL); - names = get_property(dn, "ibm,drc-names", NULL); - types = get_property(dn, "ibm,drc-types", NULL); - domains = get_property(dn, "ibm,drc-power-domains", NULL); + indexes = of_get_property(dn, "ibm,drc-indexes", NULL); + names = of_get_property(dn, "ibm,drc-names", NULL); + types = of_get_property(dn, "ibm,drc-types", NULL); + domains = of_get_property(dn, "ibm,drc-power-domains", NULL); if (!indexes || !names || !types || !domains) { /* Slot does not have dynamically-removable children */ @@ -206,7 +206,7 @@ int rpaphp_get_drc_props(struct device_node *dn, int *drc_index, char *name_tmp, *type_tmp; int i, rc; - my_index = get_property(dn, "ibm,my-drc-index", NULL); + my_index = of_get_property(dn, "ibm,my-drc-index", NULL); if (!my_index) { /* Node isn't DLPAR/hotplug capable */ return -EINVAL; diff --git a/drivers/ps3/vuart.c b/drivers/ps3/vuart.c index 7d7cab1d91b..ec2d36a1bc6 100644 --- a/drivers/ps3/vuart.c +++ b/drivers/ps3/vuart.c @@ -886,12 +886,12 @@ static int ps3_vuart_probe(struct device *_dev) if (++vuart_bus_priv.use_count == 1) { - result = ps3_alloc_vuart_irq(PS3_BINDING_CPU_ANY, + result = ps3_vuart_irq_setup(PS3_BINDING_CPU_ANY, (void*)&vuart_bus_priv.bmp.status, &vuart_bus_priv.virq); if (result) { dev_dbg(&dev->core, - "%s:%d: ps3_alloc_vuart_irq failed (%d)\n", + "%s:%d: ps3_vuart_irq_setup failed (%d)\n", __func__, __LINE__, result); result = -EPERM; goto fail_alloc_irq; @@ -937,7 +937,7 @@ static int ps3_vuart_probe(struct device *_dev) fail_probe: ps3_vuart_set_interrupt_mask(dev, 0); fail_request_irq: - ps3_free_vuart_irq(vuart_bus_priv.virq); + ps3_vuart_irq_destroy(vuart_bus_priv.virq); vuart_bus_priv.virq = NO_IRQ; fail_alloc_irq: --vuart_bus_priv.use_count; @@ -975,7 +975,7 @@ static int ps3_vuart_remove(struct device *_dev) if (--vuart_bus_priv.use_count == 0) { BUG(); free_irq(vuart_bus_priv.virq, &vuart_bus_priv); - ps3_free_vuart_irq(vuart_bus_priv.virq); + ps3_vuart_irq_destroy(vuart_bus_priv.virq); vuart_bus_priv.virq = NO_IRQ; } diff --git a/drivers/scsi/ibmvscsi/ibmvstgt.c b/drivers/scsi/ibmvscsi/ibmvstgt.c index 6d223dd7644..8ba7dd09d01 100644 --- a/drivers/scsi/ibmvscsi/ibmvstgt.c +++ b/drivers/scsi/ibmvscsi/ibmvstgt.c @@ -892,16 +892,16 @@ static int get_system_info(void) if (!rootdn) return -ENOENT; - model = get_property(rootdn, "model", NULL); - id = get_property(rootdn, "system-id", NULL); + model = of_get_property(rootdn, "model", NULL); + id = of_get_property(rootdn, "system-id", NULL); if (model && id) snprintf(system_id, sizeof(system_id), "%s-%s", model, id); - name = get_property(rootdn, "ibm,partition-name", NULL); + name = of_get_property(rootdn, "ibm,partition-name", NULL); if (name) strncpy(partition_name, name, sizeof(partition_name)); - num = get_property(rootdn, "ibm,partition-no", NULL); + num = of_get_property(rootdn, "ibm,partition-no", NULL); if (num) partition_number = *num; diff --git a/drivers/scsi/ibmvscsi/rpa_vscsi.c b/drivers/scsi/ibmvscsi/rpa_vscsi.c index 0a533f398f5..d8700aaa611 100644 --- a/drivers/scsi/ibmvscsi/rpa_vscsi.c +++ b/drivers/scsi/ibmvscsi/rpa_vscsi.c @@ -162,11 +162,11 @@ static void gather_partition_info(void) return; } - ppartition_name = get_property(rootdn, "ibm,partition-name", NULL); + ppartition_name = of_get_property(rootdn, "ibm,partition-name", NULL); if (ppartition_name) strncpy(partition_name, ppartition_name, sizeof(partition_name)); - p_number_ptr = get_property(rootdn, "ibm,partition-no", NULL); + p_number_ptr = of_get_property(rootdn, "ibm,partition-no", NULL); if (p_number_ptr) partition_number = *p_number_ptr; of_node_put(rootdn); diff --git a/drivers/scsi/mac53c94.c b/drivers/scsi/mac53c94.c index 753d88306cd..5806ede120a 100644 --- a/drivers/scsi/mac53c94.c +++ b/drivers/scsi/mac53c94.c @@ -471,7 +471,7 @@ static int mac53c94_probe(struct macio_dev *mdev, const struct of_device_id *mat goto out_free; } - clkprop = get_property(node, "clock-frequency", &proplen); + clkprop = of_get_property(node, "clock-frequency", &proplen); if (clkprop == NULL || proplen != sizeof(int)) { printk(KERN_ERR "%s: can't get clock frequency, " "assuming 25MHz\n", node->full_name); diff --git a/drivers/scsi/mesh.c b/drivers/scsi/mesh.c index 1fd3c7590d3..cf3666d7d97 100644 --- a/drivers/scsi/mesh.c +++ b/drivers/scsi/mesh.c @@ -1947,7 +1947,7 @@ static int mesh_probe(struct macio_dev *mdev, const struct of_device_id *match) ms->tgts[tgt].current_req = NULL; } - if ((cfp = get_property(mesh, "clock-frequency", NULL))) + if ((cfp = of_get_property(mesh, "clock-frequency", NULL))) ms->clk_freq = *cfp; else { printk(KERN_INFO "mesh: assuming 50MHz clock frequency\n"); diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c index 8d24cd52105..35f8b86cc78 100644 --- a/drivers/serial/mpc52xx_uart.c +++ b/drivers/serial/mpc52xx_uart.c @@ -257,9 +257,10 @@ mpc52xx_uart_shutdown(struct uart_port *port) { struct mpc52xx_psc __iomem *psc = PSC(port); - /* Shut down the port, interrupt and all */ + /* Shut down the port. Leave TX active if on a console port */ out_8(&psc->command,MPC52xx_PSC_RST_RX); - out_8(&psc->command,MPC52xx_PSC_RST_TX); + if (!uart_console(port)) + out_8(&psc->command,MPC52xx_PSC_RST_TX); port->read_status_mask = 0; out_be16(&psc->mpc52xx_psc_imr,port->read_status_mask); @@ -1069,7 +1070,7 @@ mpc52xx_uart_of_enumerate(void) continue; /* Is a particular device number requested? */ - devno = get_property(np, "port-number", NULL); + devno = of_get_property(np, "port-number", NULL); mpc52xx_uart_of_assign(of_node_get(np), devno ? *devno : -1); } diff --git a/drivers/serial/of_serial.c b/drivers/serial/of_serial.c index 336d0f4580d..7ffdaeaf054 100644 --- a/drivers/serial/of_serial.c +++ b/drivers/serial/of_serial.c @@ -29,8 +29,8 @@ static int __devinit of_platform_serial_setup(struct of_device *ofdev, int ret; memset(port, 0, sizeof *port); - spd = get_property(np, "current-speed", NULL); - clk = get_property(np, "clock-frequency", NULL); + spd = of_get_property(np, "current-speed", NULL); + clk = of_get_property(np, "clock-frequency", NULL); if (!clk) { dev_warn(&ofdev->dev, "no clock-frequency property set\n"); return -ENODEV; diff --git a/drivers/serial/pmac_zilog.c b/drivers/serial/pmac_zilog.c index be8d75721a8..0fa9f676176 100644 --- a/drivers/serial/pmac_zilog.c +++ b/drivers/serial/pmac_zilog.c @@ -1450,14 +1450,14 @@ no_dma: /* * Detect port type */ - if (device_is_compatible(np, "cobalt")) + if (of_device_is_compatible(np, "cobalt")) uap->flags |= PMACZILOG_FLAG_IS_INTMODEM; - conn = get_property(np, "AAPL,connector", &len); + conn = of_get_property(np, "AAPL,connector", &len); if (conn && (strcmp(conn, "infrared") == 0)) uap->flags |= PMACZILOG_FLAG_IS_IRDA; uap->port_type = PMAC_SCC_ASYNC; /* 1999 Powerbook G3 has slot-names property instead */ - slots = get_property(np, "slot-names", &len); + slots = of_get_property(np, "slot-names", &len); if (slots && slots->count > 0) { if (strcmp(slots->name, "IrDA") == 0) uap->flags |= PMACZILOG_FLAG_IS_IRDA; @@ -1471,7 +1471,7 @@ no_dma: of_find_node_by_name(NULL, "i2c-modem"); if (i2c_modem) { const char* mid = - get_property(i2c_modem, "modem-id", NULL); + of_get_property(i2c_modem, "modem-id", NULL); if (mid) switch(*mid) { case 0x04 : case 0x05 : diff --git a/drivers/usb/host/ehci-ps3.c b/drivers/usb/host/ehci-ps3.c index 93107453f12..37b83ba0996 100644 --- a/drivers/usb/host/ehci-ps3.c +++ b/drivers/usb/host/ehci-ps3.c @@ -97,7 +97,7 @@ static int ps3_ehci_sb_probe(struct ps3_system_bus_device *dev) dev_dbg(&dev->core, "%s:%d: mmio mapped_addr %lxh\n", __func__, __LINE__, dev->m_region->lpar_addr); - result = ps3_alloc_io_irq(PS3_BINDING_CPU_ANY, dev->interrupt_id, &virq); + result = ps3_io_irq_setup(PS3_BINDING_CPU_ANY, dev->interrupt_id, &virq); if (result) { dev_dbg(&dev->core, "%s:%d: ps3_construct_io_irq(%d) failed.\n", @@ -155,7 +155,7 @@ fail_add_hcd: fail_ioremap: usb_put_hcd(hcd); fail_create_hcd: - ps3_free_io_irq(virq); + ps3_io_irq_destroy(virq); fail_irq: ps3_free_mmio_region(dev->m_region); fail_mmio: diff --git a/drivers/usb/host/ohci-ppc-of.c b/drivers/usb/host/ohci-ppc-of.c index 08e237c7bc4..c43b66acd4d 100644 --- a/drivers/usb/host/ohci-ppc-of.c +++ b/drivers/usb/host/ohci-ppc-of.c @@ -97,8 +97,8 @@ ohci_hcd_ppc_of_probe(struct of_device *op, const struct of_device_id *match) return -ENODEV; is_bigendian = - device_is_compatible(dn, "ohci-bigendian") || - device_is_compatible(dn, "ohci-be"); + of_device_is_compatible(dn, "ohci-bigendian") || + of_device_is_compatible(dn, "ohci-be"); dev_dbg(&op->dev, "initializing PPC-OF USB Controller\n"); diff --git a/drivers/usb/host/ohci-ps3.c b/drivers/usb/host/ohci-ps3.c index c849f72b508..d7cf07288b0 100644 --- a/drivers/usb/host/ohci-ps3.c +++ b/drivers/usb/host/ohci-ps3.c @@ -99,7 +99,7 @@ static int ps3_ohci_sb_probe(struct ps3_system_bus_device *dev) dev_dbg(&dev->core, "%s:%d: mmio mapped_addr %lxh\n", __func__, __LINE__, dev->m_region->lpar_addr); - result = ps3_alloc_io_irq(PS3_BINDING_CPU_ANY, dev->interrupt_id, &virq); + result = ps3_io_irq_setup(PS3_BINDING_CPU_ANY, dev->interrupt_id, &virq); if (result) { dev_dbg(&dev->core, "%s:%d: ps3_construct_io_irq(%d) failed.\n", @@ -157,7 +157,7 @@ fail_add_hcd: fail_ioremap: usb_put_hcd(hcd); fail_create_hcd: - ps3_free_io_irq(virq); + ps3_io_irq_destroy(virq); fail_irq: ps3_free_mmio_region(dev->m_region); fail_mmio: diff --git a/drivers/video/aty/radeon_base.c b/drivers/video/aty/radeon_base.c index a4b3fd185de..9d629fe1709 100644 --- a/drivers/video/aty/radeon_base.c +++ b/drivers/video/aty/radeon_base.c @@ -422,7 +422,7 @@ static int __devinit radeon_read_xtal_OF (struct radeonfb_info *rinfo) if (dp == NULL) return -ENODEV; - val = get_property(dp, "ATY,RefCLK", NULL); + val = of_get_property(dp, "ATY,RefCLK", NULL); if (!val || !*val) { printk(KERN_WARNING "radeonfb: No ATY,RefCLK property !\n"); return -EINVAL; @@ -430,11 +430,11 @@ static int __devinit radeon_read_xtal_OF (struct radeonfb_info *rinfo) rinfo->pll.ref_clk = (*val) / 10; - val = get_property(dp, "ATY,SCLK", NULL); + val = of_get_property(dp, "ATY,SCLK", NULL); if (val && *val) rinfo->pll.sclk = (*val) / 10; - val = get_property(dp, "ATY,MCLK", NULL); + val = of_get_property(dp, "ATY,MCLK", NULL); if (val && *val) rinfo->pll.mclk = (*val) / 10; diff --git a/drivers/video/aty/radeon_monitor.c b/drivers/video/aty/radeon_monitor.c index 737b5c09dbd..2030ed81342 100644 --- a/drivers/video/aty/radeon_monitor.c +++ b/drivers/video/aty/radeon_monitor.c @@ -70,7 +70,7 @@ static int __devinit radeon_parse_montype_prop(struct device_node *dp, u8 **out_ int i, mt = MT_NONE; RTRACE("analyzing OF properties...\n"); - pmt = get_property(dp, "display-type", NULL); + pmt = of_get_property(dp, "display-type", NULL); if (!pmt) return MT_NONE; RTRACE("display-type: %s\n", pmt); @@ -89,7 +89,7 @@ static int __devinit radeon_parse_montype_prop(struct device_node *dp, u8 **out_ } for (i = 0; propnames[i] != NULL; ++i) { - pedid = get_property(dp, propnames[i], NULL); + pedid = of_get_property(dp, propnames[i], NULL); if (pedid != NULL) break; } @@ -98,9 +98,10 @@ static int __devinit radeon_parse_montype_prop(struct device_node *dp, u8 **out_ * single-head cards have hdno == -1 and skip this step */ if (pedid == NULL && dp->parent && (hdno != -1)) - pedid = get_property(dp->parent, (hdno == 0) ? "EDID1" : "EDID2", NULL); + pedid = of_get_property(dp->parent, + (hdno == 0) ? "EDID1" : "EDID2", NULL); if (pedid == NULL && dp->parent && (hdno == 0)) - pedid = get_property(dp->parent, "EDID", NULL); + pedid = of_get_property(dp->parent, "EDID", NULL); if (pedid == NULL) return mt; @@ -130,7 +131,7 @@ static int __devinit radeon_probe_OF_head(struct radeonfb_info *rinfo, int head_ do { if (!dp) return MT_NONE; - pname = get_property(dp, "name", NULL); + pname = of_get_property(dp, "name", NULL); if (!pname) return MT_NONE; len = strlen(pname); diff --git a/drivers/video/aty/radeon_pm.c b/drivers/video/aty/radeon_pm.c index c411293cefc..1786ae18832 100644 --- a/drivers/video/aty/radeon_pm.c +++ b/drivers/video/aty/radeon_pm.c @@ -1290,7 +1290,7 @@ static void radeon_pm_full_reset_sdram(struct radeonfb_info *rinfo) if (rinfo->of_node != NULL) { int size; - mrtable = get_property(rinfo->of_node, "ATY,MRT", &size); + mrtable = of_get_property(rinfo->of_node, "ATY,MRT", &size); if (mrtable) mrtable_size = size >> 2; else diff --git a/drivers/video/nvidia/nv_of.c b/drivers/video/nvidia/nv_of.c index 163a774a1b3..73afd7eb997 100644 --- a/drivers/video/nvidia/nv_of.c +++ b/drivers/video/nvidia/nv_of.c @@ -46,15 +46,15 @@ int nvidia_probe_of_connector(struct fb_info *info, int conn, u8 **out_edid) for (dp = NULL; (dp = of_get_next_child(parent, dp)) != NULL;) { - pname = get_property(dp, "name", NULL); + pname = of_get_property(dp, "name", NULL); if (!pname) continue; len = strlen(pname); if ((pname[len-1] == 'A' && conn == 1) || (pname[len-1] == 'B' && conn == 2)) { for (i = 0; propnames[i] != NULL; ++i) { - pedid = get_property(dp, propnames[i], - NULL); + pedid = of_get_property(dp, + propnames[i], NULL); if (pedid != NULL) break; } @@ -65,7 +65,7 @@ int nvidia_probe_of_connector(struct fb_info *info, int conn, u8 **out_edid) } if (pedid == NULL) { for (i = 0; propnames[i] != NULL; ++i) { - pedid = get_property(parent, propnames[i], NULL); + pedid = of_get_property(parent, propnames[i], NULL); if (pedid != NULL) break; } diff --git a/drivers/video/offb.c b/drivers/video/offb.c index 9576a55eaf1..885b42836cb 100644 --- a/drivers/video/offb.c +++ b/drivers/video/offb.c @@ -322,8 +322,8 @@ static void __init offb_init_fb(const char *name, const char *full_name, ioremap(base + 0x7ff000, 0x1000) + 0xcc0; par->cmap_data = par->cmap_adr + 1; par->cmap_type = cmap_m64; - } else if (dp && (device_is_compatible(dp, "pci1014,b7") || - device_is_compatible(dp, "pci1014,21c"))) { + } else if (dp && (of_device_is_compatible(dp, "pci1014,b7") || + of_device_is_compatible(dp, "pci1014,21c"))) { par->cmap_adr = offb_map_reg(dp, 0, 0x6000, 0x1000); if (par->cmap_adr) par->cmap_type = cmap_gxt2000; @@ -425,27 +425,27 @@ static void __init offb_init_nodriver(struct device_node *dp, int no_real_node) const u32 *pp, *addrp, *up; u64 asize; - pp = get_property(dp, "linux,bootx-depth", &len); + pp = of_get_property(dp, "linux,bootx-depth", &len); if (pp == NULL) - pp = get_property(dp, "depth", &len); + pp = of_get_property(dp, "depth", &len); if (pp && len == sizeof(u32)) depth = *pp; - pp = get_property(dp, "linux,bootx-width", &len); + pp = of_get_property(dp, "linux,bootx-width", &len); if (pp == NULL) - pp = get_property(dp, "width", &len); + pp = of_get_property(dp, "width", &len); if (pp && len == sizeof(u32)) width = *pp; - pp = get_property(dp, "linux,bootx-height", &len); + pp = of_get_property(dp, "linux,bootx-height", &len); if (pp == NULL) - pp = get_property(dp, "height", &len); + pp = of_get_property(dp, "height", &len); if (pp && len == sizeof(u32)) height = *pp; - pp = get_property(dp, "linux,bootx-linebytes", &len); + pp = of_get_property(dp, "linux,bootx-linebytes", &len); if (pp == NULL) - pp = get_property(dp, "linebytes", &len); + pp = of_get_property(dp, "linebytes", &len); if (pp && len == sizeof(u32) && (*pp != 0xffffffffu)) pitch = *pp; else @@ -463,9 +463,9 @@ static void __init offb_init_nodriver(struct device_node *dp, int no_real_node) * ranges and pick one that is both big enough and if possible encloses * the "address" property. If none match, we pick the biggest */ - up = get_property(dp, "linux,bootx-addr", &len); + up = of_get_property(dp, "linux,bootx-addr", &len); if (up == NULL) - up = get_property(dp, "address", &len); + up = of_get_property(dp, "address", &len); if (up && len == sizeof(u32)) addr_prop = *up; @@ -521,7 +521,7 @@ static int __init offb_init(void) return -ENODEV; /* Check if we have a MacOS display without a node spec */ - if (get_property(of_chosen, "linux,bootx-noscreen", NULL) != NULL) { + if (of_get_property(of_chosen, "linux,bootx-noscreen", NULL) != NULL) { /* The old code tried to work out which node was the MacOS * display based on the address. I'm dropping that since the * lack of a node spec only happens with old BootX versions @@ -532,14 +532,14 @@ static int __init offb_init(void) } for (dp = NULL; (dp = of_find_node_by_type(dp, "display"));) { - if (get_property(dp, "linux,opened", NULL) && - get_property(dp, "linux,boot-display", NULL)) { + if (of_get_property(dp, "linux,opened", NULL) && + of_get_property(dp, "linux,boot-display", NULL)) { boot_disp = dp; offb_init_nodriver(dp, 0); } } for (dp = NULL; (dp = of_find_node_by_type(dp, "display"));) { - if (get_property(dp, "linux,opened", NULL) && + if (of_get_property(dp, "linux,opened", NULL) && dp != boot_disp) offb_init_nodriver(dp, 0); } diff --git a/drivers/video/ps3fb.c b/drivers/video/ps3fb.c index 07d1979bc23..9756a728b74 100644 --- a/drivers/video/ps3fb.c +++ b/drivers/video/ps3fb.c @@ -898,8 +898,8 @@ static int ps3fb_vsync_settings(struct gpu_driver_info *dinfo, void *dev) } ps3fb.dev = dev; - error = ps3_alloc_irq(PS3_BINDING_CPU_ANY, dinfo->irq.irq_outlet, - &ps3fb.irq_no); + error = ps3_irq_plug_setup(PS3_BINDING_CPU_ANY, dinfo->irq.irq_outlet, + &ps3fb.irq_no); if (error) { printk(KERN_ERR "%s: ps3_alloc_irq failed %d\n", __func__, error); @@ -911,7 +911,7 @@ static int ps3fb_vsync_settings(struct gpu_driver_info *dinfo, void *dev) if (error) { printk(KERN_ERR "%s: request_irq failed %d\n", __func__, error); - ps3_free_irq(ps3fb.irq_no); + ps3_irq_plug_destroy(ps3fb.irq_no); return error; } @@ -1083,7 +1083,7 @@ err_framebuffer_release: framebuffer_release(info); err_free_irq: free_irq(ps3fb.irq_no, ps3fb.dev); - ps3_free_irq(ps3fb.irq_no); + ps3_irq_plug_destroy(ps3fb.irq_no); err_iounmap_dinfo: iounmap((u8 __iomem *)ps3fb.dinfo); err_gpu_context_free: @@ -1099,7 +1099,7 @@ static void ps3fb_shutdown(struct platform_device *dev) ps3fb_flip_ctl(0); /* flip off */ ps3fb.dinfo->irq.mask = 0; free_irq(ps3fb.irq_no, ps3fb.dev); - ps3_free_irq(ps3fb.irq_no); + ps3_irq_plug_destroy(ps3fb.irq_no); iounmap((u8 __iomem *)ps3fb.dinfo); } @@ -1114,7 +1114,7 @@ void ps3fb_cleanup(void) } if (ps3fb.irq_no) { free_irq(ps3fb.irq_no, ps3fb.dev); - ps3_free_irq(ps3fb.irq_no); + ps3_irq_plug_destroy(ps3fb.irq_no); } iounmap((u8 __iomem *)ps3fb.dinfo); diff --git a/drivers/video/riva/fbdev.c b/drivers/video/riva/fbdev.c index d7ece8d17a2..9c6bd099185 100644 --- a/drivers/video/riva/fbdev.c +++ b/drivers/video/riva/fbdev.c @@ -1760,13 +1760,13 @@ static int __devinit riva_get_EDID_OF(struct fb_info *info, struct pci_dev *pd) NVTRACE_ENTER(); dp = pci_device_to_OF_node(pd); for (; dp != NULL; dp = dp->child) { - disptype = get_property(dp, "display-type", NULL); + disptype = of_get_property(dp, "display-type", NULL); if (disptype == NULL) continue; if (strncmp(disptype, "LCD", 3) != 0) continue; for (i = 0; propnames[i] != NULL; ++i) { - pedid = get_property(dp, propnames[i], NULL); + pedid = of_get_property(dp, propnames[i], NULL); if (pedid != NULL) { par->EDID = (unsigned char *)pedid; NVTRACE("LCD found.\n"); diff --git a/include/asm-powerpc/iommu.h b/include/asm-powerpc/iommu.h index b2e56b30306..870967e4720 100644 --- a/include/asm-powerpc/iommu.h +++ b/include/asm-powerpc/iommu.h @@ -26,6 +26,7 @@ #include <linux/spinlock.h> #include <linux/device.h> #include <linux/dma-mapping.h> +#include <asm/machdep.h> #include <asm/types.h> #include <asm/bitops.h> @@ -109,6 +110,19 @@ static inline void pci_iommu_init(void) { } #endif extern void alloc_dart_table(void); +#if defined(CONFIG_PPC64) && defined(CONFIG_PM) +static inline void iommu_save(void) +{ + if (ppc_md.iommu_save) + ppc_md.iommu_save(); +} + +static inline void iommu_restore(void) +{ + if (ppc_md.iommu_restore) + ppc_md.iommu_restore(); +} +#endif #endif /* __KERNEL__ */ #endif /* _ASM_IOMMU_H */ diff --git a/include/asm-powerpc/kdebug.h b/include/asm-powerpc/kdebug.h index 532bfee934f..df996b933de 100644 --- a/include/asm-powerpc/kdebug.h +++ b/include/asm-powerpc/kdebug.h @@ -18,8 +18,20 @@ struct die_args { extern int register_die_notifier(struct notifier_block *); extern int unregister_die_notifier(struct notifier_block *); -extern int register_page_fault_notifier(struct notifier_block *); -extern int unregister_page_fault_notifier(struct notifier_block *); + +/* + * These are only here because kprobes.c wants them to implement a + * blatant layering violation. Will hopefully go away soon once all + * architectures are updated. + */ +static inline int register_page_fault_notifier(struct notifier_block *nb) +{ + return 0; +} +static inline int unregister_page_fault_notifier(struct notifier_block *nb) +{ + return 0; +} extern struct atomic_notifier_head powerpc_die_chain; /* Grossly misnamed. */ @@ -29,7 +41,6 @@ enum die_val { DIE_DABR_MATCH, DIE_BPT, DIE_SSTEP, - DIE_PAGE_FAULT, }; static inline int notify_die(enum die_val val,char *str,struct pt_regs *regs,long err,int trap, int sig) diff --git a/include/asm-powerpc/kprobes.h b/include/asm-powerpc/kprobes.h index f850ca7020e..b0e40ff32ee 100644 --- a/include/asm-powerpc/kprobes.h +++ b/include/asm-powerpc/kprobes.h @@ -64,6 +64,12 @@ typedef unsigned int kprobe_opcode_t; addr = *(kprobe_opcode_t **)addr; \ } else if (name[0] != '.') \ addr = *(kprobe_opcode_t **)addr; \ + } else { \ + char dot_name[KSYM_NAME_LEN+1]; \ + dot_name[0] = '.'; \ + dot_name[1] = '\0'; \ + strncat(dot_name, name, KSYM_NAME_LEN); \ + addr = (kprobe_opcode_t *)kallsyms_lookup_name(dot_name); \ } \ } @@ -110,5 +116,6 @@ struct kprobe_ctlblk { extern int kprobe_exceptions_notify(struct notifier_block *self, unsigned long val, void *data); +extern int kprobe_fault_handler(struct pt_regs *regs, int trapnr); #endif /* __KERNEL__ */ #endif /* _ASM_POWERPC_KPROBES_H */ diff --git a/include/asm-powerpc/machdep.h b/include/asm-powerpc/machdep.h index b204926ce91..6fdabd6dfb3 100644 --- a/include/asm-powerpc/machdep.h +++ b/include/asm-powerpc/machdep.h @@ -91,6 +91,11 @@ struct machdep_calls { void __iomem * (*ioremap)(phys_addr_t addr, unsigned long size, unsigned long flags); void (*iounmap)(volatile void __iomem *token); + +#ifdef CONFIG_PM + void (*iommu_save)(void); + void (*iommu_restore)(void); +#endif #endif /* CONFIG_PPC64 */ int (*probe)(void); @@ -248,6 +253,7 @@ struct machdep_calls { }; extern void power4_idle(void); +extern void power4_cpu_offline_powersave(void); extern void ppc6xx_idle(void); /* diff --git a/include/asm-powerpc/mmu-44x.h b/include/asm-powerpc/mmu-44x.h new file mode 100644 index 00000000000..7bbc37e27d3 --- /dev/null +++ b/include/asm-powerpc/mmu-44x.h @@ -0,0 +1,72 @@ +#ifndef _ASM_POWERPC_MMU_44X_H_ +#define _ASM_POWERPC_MMU_44X_H_ +/* + * PPC440 support + */ + +#define PPC44x_MMUCR_TID 0x000000ff +#define PPC44x_MMUCR_STS 0x00010000 + +#define PPC44x_TLB_PAGEID 0 +#define PPC44x_TLB_XLAT 1 +#define PPC44x_TLB_ATTRIB 2 + +/* Page identification fields */ +#define PPC44x_TLB_EPN_MASK 0xfffffc00 /* Effective Page Number */ +#define PPC44x_TLB_VALID 0x00000200 /* Valid flag */ +#define PPC44x_TLB_TS 0x00000100 /* Translation address space */ +#define PPC44x_TLB_1K 0x00000000 /* Page sizes */ +#define PPC44x_TLB_4K 0x00000010 +#define PPC44x_TLB_16K 0x00000020 +#define PPC44x_TLB_64K 0x00000030 +#define PPC44x_TLB_256K 0x00000040 +#define PPC44x_TLB_1M 0x00000050 +#define PPC44x_TLB_16M 0x00000070 +#define PPC44x_TLB_256M 0x00000090 + +/* Translation fields */ +#define PPC44x_TLB_RPN_MASK 0xfffffc00 /* Real Page Number */ +#define PPC44x_TLB_ERPN_MASK 0x0000000f + +/* Storage attribute and access control fields */ +#define PPC44x_TLB_ATTR_MASK 0x0000ff80 +#define PPC44x_TLB_U0 0x00008000 /* User 0 */ +#define PPC44x_TLB_U1 0x00004000 /* User 1 */ +#define PPC44x_TLB_U2 0x00002000 /* User 2 */ +#define PPC44x_TLB_U3 0x00001000 /* User 3 */ +#define PPC44x_TLB_W 0x00000800 /* Caching is write-through */ +#define PPC44x_TLB_I 0x00000400 /* Caching is inhibited */ +#define PPC44x_TLB_M 0x00000200 /* Memory is coherent */ +#define PPC44x_TLB_G 0x00000100 /* Memory is guarded */ +#define PPC44x_TLB_E 0x00000080 /* Memory is guarded */ + +#define PPC44x_TLB_PERM_MASK 0x0000003f +#define PPC44x_TLB_UX 0x00000020 /* User execution */ +#define PPC44x_TLB_UW 0x00000010 /* User write */ +#define PPC44x_TLB_UR 0x00000008 /* User read */ +#define PPC44x_TLB_SX 0x00000004 /* Super execution */ +#define PPC44x_TLB_SW 0x00000002 /* Super write */ +#define PPC44x_TLB_SR 0x00000001 /* Super read */ + +/* Number of TLB entries */ +#define PPC44x_TLB_SIZE 64 + +#ifndef __ASSEMBLY__ + +typedef unsigned long long phys_addr_t; + +extern phys_addr_t fixup_bigphys_addr(phys_addr_t, phys_addr_t); + +typedef struct { + unsigned long id; + unsigned long vdso_base; +} mm_context_t; + +#endif /* !__ASSEMBLY__ */ + +#define PPC44x_EARLY_TLBS 1 + +/* Size of the TLBs used for pinning in lowmem */ +#define PPC_PIN_SIZE (1 << 28) /* 256M */ + +#endif /* _ASM_POWERPC_MMU_44X_H_ */ diff --git a/include/asm-powerpc/mmu.h b/include/asm-powerpc/mmu.h index 06b3e6d336c..fe510fff890 100644 --- a/include/asm-powerpc/mmu.h +++ b/include/asm-powerpc/mmu.h @@ -5,9 +5,12 @@ #ifdef CONFIG_PPC64 /* 64-bit classic hash table MMU */ # include <asm/mmu-hash64.h> +#elif defined(CONFIG_44x) +/* 44x-style software loaded TLB */ +# include <asm/mmu-44x.h> #else -/* 32-bit. FIXME: split up the 32-bit MMU types, and revise for - * arch/powerpc */ +/* Other 32-bit. FIXME: split up the other 32-bit MMU types, and + * revise for arch/powerpc */ # include <asm-ppc/mmu.h> #endif diff --git a/include/asm-powerpc/mpc52xx.h b/include/asm-powerpc/mpc52xx.h index 7afd5bf9452..c4631f6dd4f 100644 --- a/include/asm-powerpc/mpc52xx.h +++ b/include/asm-powerpc/mpc52xx.h @@ -253,5 +253,16 @@ extern int __init mpc52xx_add_bridge(struct device_node *node); #endif /* __ASSEMBLY__ */ +#ifdef CONFIG_PM +struct mpc52xx_suspend { + void (*board_suspend_prepare)(void __iomem *mbar); + void (*board_resume_finish)(void __iomem *mbar); +}; + +extern struct mpc52xx_suspend mpc52xx_suspend; +extern int __init mpc52xx_pm_init(void); +extern int mpc52xx_set_wakeup_gpio(u8 pin, u8 level); +#endif /* CONFIG_PM */ + #endif /* __ASM_POWERPC_MPC52xx_H__ */ diff --git a/include/asm-powerpc/mpic.h b/include/asm-powerpc/mpic.h index e4d5fc5362a..22c85c4f5b2 100644 --- a/include/asm-powerpc/mpic.h +++ b/include/asm-powerpc/mpic.h @@ -3,6 +3,7 @@ #ifdef __KERNEL__ #include <linux/irq.h> +#include <linux/sysdev.h> #include <asm/dcr.h> /* @@ -228,6 +229,14 @@ struct mpic_reg_bank { #endif /* CONFIG_PPC_DCR */ }; +struct mpic_irq_save { + u32 vecprio, + dest; +#ifdef CONFIG_MPIC_U3_HT_IRQS + u32 fixup_data; +#endif +}; + /* The instance data of a given MPIC */ struct mpic { @@ -294,6 +303,12 @@ struct mpic /* link */ struct mpic *next; + + struct sys_device sysdev; + +#ifdef CONFIG_PM + struct mpic_irq_save *save_data; +#endif }; /* diff --git a/include/asm-powerpc/of_device.h b/include/asm-powerpc/of_device.h index 4f1aabe0ce7..e9af49eb1aa 100644 --- a/include/asm-powerpc/of_device.h +++ b/include/asm-powerpc/of_device.h @@ -32,6 +32,8 @@ extern int of_device_register(struct of_device *ofdev); extern void of_device_unregister(struct of_device *ofdev); extern void of_release_dev(struct device *dev); +extern ssize_t of_device_get_modalias(struct of_device *ofdev, + char *str, ssize_t len); extern int of_device_uevent(struct device *dev, char **envp, int num_envp, char *buffer, int buffer_size); diff --git a/include/asm-powerpc/page.h b/include/asm-powerpc/page.h index b4d38b0b15f..f37bff0ee88 100644 --- a/include/asm-powerpc/page.h +++ b/include/asm-powerpc/page.h @@ -126,7 +126,7 @@ typedef struct { unsigned long pmd; } pmd_t; #define __pmd(x) ((pmd_t) { (x) }) /* PUD level exusts only on 4k pages */ -#ifndef CONFIG_PPC_64K_PAGES +#if defined(CONFIG_PPC64) && !defined(CONFIG_PPC_64K_PAGES) typedef struct { unsigned long pud; } pud_t; #define pud_val(x) ((x).pud) #define __pud(x) ((pud_t) { (x) }) diff --git a/include/asm-powerpc/page_32.h b/include/asm-powerpc/page_32.h index 07f6d3cf5e5..374d0db37e1 100644 --- a/include/asm-powerpc/page_32.h +++ b/include/asm-powerpc/page_32.h @@ -14,11 +14,9 @@ #ifdef CONFIG_PTE_64BIT typedef unsigned long long pte_basic_t; #define PTE_SHIFT (PAGE_SHIFT - 3) /* 512 ptes per page */ -#define PTE_FMT "%16Lx" #else typedef unsigned long pte_basic_t; #define PTE_SHIFT (PAGE_SHIFT - 2) /* 1024 ptes per page */ -#define PTE_FMT "%.8lx" #endif struct page; diff --git a/include/asm-powerpc/pgalloc-32.h b/include/asm-powerpc/pgalloc-32.h new file mode 100644 index 00000000000..235aef283ed --- /dev/null +++ b/include/asm-powerpc/pgalloc-32.h @@ -0,0 +1,41 @@ +#ifndef _ASM_POWERPC_PGALLOC_32_H +#define _ASM_POWERPC_PGALLOC_32_H + +#include <linux/threads.h> + +extern void __bad_pte(pmd_t *pmd); + +extern pgd_t *pgd_alloc(struct mm_struct *mm); +extern void pgd_free(pgd_t *pgd); + +/* + * We don't have any real pmd's, and this code never triggers because + * the pgd will always be present.. + */ +#define pmd_alloc_one(mm,address) ({ BUG(); ((pmd_t *)2); }) +#define pmd_free(x) do { } while (0) +#define __pmd_free_tlb(tlb,x) do { } while (0) +#define pgd_populate(mm, pmd, pte) BUG() + +#ifndef CONFIG_BOOKE +#define pmd_populate_kernel(mm, pmd, pte) \ + (pmd_val(*(pmd)) = __pa(pte) | _PMD_PRESENT) +#define pmd_populate(mm, pmd, pte) \ + (pmd_val(*(pmd)) = (page_to_pfn(pte) << PAGE_SHIFT) | _PMD_PRESENT) +#else +#define pmd_populate_kernel(mm, pmd, pte) \ + (pmd_val(*(pmd)) = (unsigned long)pte | _PMD_PRESENT) +#define pmd_populate(mm, pmd, pte) \ + (pmd_val(*(pmd)) = (unsigned long)lowmem_page_address(pte) | _PMD_PRESENT) +#endif + +extern pte_t *pte_alloc_one_kernel(struct mm_struct *mm, unsigned long addr); +extern struct page *pte_alloc_one(struct mm_struct *mm, unsigned long addr); +extern void pte_free_kernel(pte_t *pte); +extern void pte_free(struct page *pte); + +#define __pte_free_tlb(tlb, pte) pte_free((pte)) + +#define check_pgt_cache() do { } while (0) + +#endif /* _ASM_POWERPC_PGALLOC_32_H */ diff --git a/include/asm-powerpc/pgalloc-64.h b/include/asm-powerpc/pgalloc-64.h new file mode 100644 index 00000000000..30b50cf56e2 --- /dev/null +++ b/include/asm-powerpc/pgalloc-64.h @@ -0,0 +1,152 @@ +#ifndef _ASM_POWERPC_PGALLOC_64_H +#define _ASM_POWERPC_PGALLOC_64_H +/* + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#include <linux/mm.h> +#include <linux/slab.h> +#include <linux/cpumask.h> +#include <linux/percpu.h> + +extern struct kmem_cache *pgtable_cache[]; + +#ifdef CONFIG_PPC_64K_PAGES +#define PTE_CACHE_NUM 0 +#define PMD_CACHE_NUM 1 +#define PGD_CACHE_NUM 2 +#define HUGEPTE_CACHE_NUM 3 +#else +#define PTE_CACHE_NUM 0 +#define PMD_CACHE_NUM 1 +#define PUD_CACHE_NUM 1 +#define PGD_CACHE_NUM 0 +#define HUGEPTE_CACHE_NUM 2 +#endif + +static inline pgd_t *pgd_alloc(struct mm_struct *mm) +{ + return kmem_cache_alloc(pgtable_cache[PGD_CACHE_NUM], GFP_KERNEL); +} + +static inline void pgd_free(pgd_t *pgd) +{ + kmem_cache_free(pgtable_cache[PGD_CACHE_NUM], pgd); +} + +#ifndef CONFIG_PPC_64K_PAGES + +#define pgd_populate(MM, PGD, PUD) pgd_set(PGD, PUD) + +static inline pud_t *pud_alloc_one(struct mm_struct *mm, unsigned long addr) +{ + return kmem_cache_alloc(pgtable_cache[PUD_CACHE_NUM], + GFP_KERNEL|__GFP_REPEAT); +} + +static inline void pud_free(pud_t *pud) +{ + kmem_cache_free(pgtable_cache[PUD_CACHE_NUM], pud); +} + +static inline void pud_populate(struct mm_struct *mm, pud_t *pud, pmd_t *pmd) +{ + pud_set(pud, (unsigned long)pmd); +} + +#define pmd_populate(mm, pmd, pte_page) \ + pmd_populate_kernel(mm, pmd, page_address(pte_page)) +#define pmd_populate_kernel(mm, pmd, pte) pmd_set(pmd, (unsigned long)(pte)) + + +#else /* CONFIG_PPC_64K_PAGES */ + +#define pud_populate(mm, pud, pmd) pud_set(pud, (unsigned long)pmd) + +static inline void pmd_populate_kernel(struct mm_struct *mm, pmd_t *pmd, + pte_t *pte) +{ + pmd_set(pmd, (unsigned long)pte); +} + +#define pmd_populate(mm, pmd, pte_page) \ + pmd_populate_kernel(mm, pmd, page_address(pte_page)) + +#endif /* CONFIG_PPC_64K_PAGES */ + +static inline pmd_t *pmd_alloc_one(struct mm_struct *mm, unsigned long addr) +{ + return kmem_cache_alloc(pgtable_cache[PMD_CACHE_NUM], + GFP_KERNEL|__GFP_REPEAT); +} + +static inline void pmd_free(pmd_t *pmd) +{ + kmem_cache_free(pgtable_cache[PMD_CACHE_NUM], pmd); +} + +static inline pte_t *pte_alloc_one_kernel(struct mm_struct *mm, + unsigned long address) +{ + return kmem_cache_alloc(pgtable_cache[PTE_CACHE_NUM], + GFP_KERNEL|__GFP_REPEAT); +} + +static inline struct page *pte_alloc_one(struct mm_struct *mm, + unsigned long address) +{ + return virt_to_page(pte_alloc_one_kernel(mm, address)); +} + +static inline void pte_free_kernel(pte_t *pte) +{ + kmem_cache_free(pgtable_cache[PTE_CACHE_NUM], pte); +} + +static inline void pte_free(struct page *ptepage) +{ + pte_free_kernel(page_address(ptepage)); +} + +#define PGF_CACHENUM_MASK 0x3 + +typedef struct pgtable_free { + unsigned long val; +} pgtable_free_t; + +static inline pgtable_free_t pgtable_free_cache(void *p, int cachenum, + unsigned long mask) +{ + BUG_ON(cachenum > PGF_CACHENUM_MASK); + + return (pgtable_free_t){.val = ((unsigned long) p & ~mask) | cachenum}; +} + +static inline void pgtable_free(pgtable_free_t pgf) +{ + void *p = (void *)(pgf.val & ~PGF_CACHENUM_MASK); + int cachenum = pgf.val & PGF_CACHENUM_MASK; + + kmem_cache_free(pgtable_cache[cachenum], p); +} + +extern void pgtable_free_tlb(struct mmu_gather *tlb, pgtable_free_t pgf); + +#define __pte_free_tlb(tlb, ptepage) \ + pgtable_free_tlb(tlb, pgtable_free_cache(page_address(ptepage), \ + PTE_CACHE_NUM, PTE_TABLE_SIZE-1)) +#define __pmd_free_tlb(tlb, pmd) \ + pgtable_free_tlb(tlb, pgtable_free_cache(pmd, \ + PMD_CACHE_NUM, PMD_TABLE_SIZE-1)) +#ifndef CONFIG_PPC_64K_PAGES +#define __pud_free_tlb(tlb, pud) \ + pgtable_free_tlb(tlb, pgtable_free_cache(pud, \ + PUD_CACHE_NUM, PUD_TABLE_SIZE-1)) +#endif /* CONFIG_PPC_64K_PAGES */ + +#define check_pgt_cache() do { } while (0) + +#endif /* _ASM_POWERPC_PGALLOC_64_H */ diff --git a/include/asm-powerpc/pgalloc.h b/include/asm-powerpc/pgalloc.h index b0830db68f8..b4505ed0f0f 100644 --- a/include/asm-powerpc/pgalloc.h +++ b/include/asm-powerpc/pgalloc.h @@ -2,159 +2,11 @@ #define _ASM_POWERPC_PGALLOC_H #ifdef __KERNEL__ -#ifndef CONFIG_PPC64 -#include <asm-ppc/pgalloc.h> +#ifdef CONFIG_PPC64 +#include <asm/pgalloc-64.h> #else - -#include <linux/mm.h> -#include <linux/slab.h> -#include <linux/cpumask.h> -#include <linux/percpu.h> - -extern struct kmem_cache *pgtable_cache[]; - -#ifdef CONFIG_PPC_64K_PAGES -#define PTE_CACHE_NUM 0 -#define PMD_CACHE_NUM 1 -#define PGD_CACHE_NUM 2 -#define HUGEPTE_CACHE_NUM 3 -#else -#define PTE_CACHE_NUM 0 -#define PMD_CACHE_NUM 1 -#define PUD_CACHE_NUM 1 -#define PGD_CACHE_NUM 0 -#define HUGEPTE_CACHE_NUM 2 +#include <asm/pgalloc-32.h> #endif -/* - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 2 of the License, or (at your option) any later version. - */ - -static inline pgd_t *pgd_alloc(struct mm_struct *mm) -{ - return kmem_cache_alloc(pgtable_cache[PGD_CACHE_NUM], GFP_KERNEL); -} - -static inline void pgd_free(pgd_t *pgd) -{ - kmem_cache_free(pgtable_cache[PGD_CACHE_NUM], pgd); -} - -#ifndef CONFIG_PPC_64K_PAGES - -#define pgd_populate(MM, PGD, PUD) pgd_set(PGD, PUD) - -static inline pud_t *pud_alloc_one(struct mm_struct *mm, unsigned long addr) -{ - return kmem_cache_alloc(pgtable_cache[PUD_CACHE_NUM], - GFP_KERNEL|__GFP_REPEAT); -} - -static inline void pud_free(pud_t *pud) -{ - kmem_cache_free(pgtable_cache[PUD_CACHE_NUM], pud); -} - -static inline void pud_populate(struct mm_struct *mm, pud_t *pud, pmd_t *pmd) -{ - pud_set(pud, (unsigned long)pmd); -} - -#define pmd_populate(mm, pmd, pte_page) \ - pmd_populate_kernel(mm, pmd, page_address(pte_page)) -#define pmd_populate_kernel(mm, pmd, pte) pmd_set(pmd, (unsigned long)(pte)) - - -#else /* CONFIG_PPC_64K_PAGES */ - -#define pud_populate(mm, pud, pmd) pud_set(pud, (unsigned long)pmd) - -static inline void pmd_populate_kernel(struct mm_struct *mm, pmd_t *pmd, - pte_t *pte) -{ - pmd_set(pmd, (unsigned long)pte); -} - -#define pmd_populate(mm, pmd, pte_page) \ - pmd_populate_kernel(mm, pmd, page_address(pte_page)) - -#endif /* CONFIG_PPC_64K_PAGES */ - -static inline pmd_t *pmd_alloc_one(struct mm_struct *mm, unsigned long addr) -{ - return kmem_cache_alloc(pgtable_cache[PMD_CACHE_NUM], - GFP_KERNEL|__GFP_REPEAT); -} - -static inline void pmd_free(pmd_t *pmd) -{ - kmem_cache_free(pgtable_cache[PMD_CACHE_NUM], pmd); -} - -static inline pte_t *pte_alloc_one_kernel(struct mm_struct *mm, - unsigned long address) -{ - return kmem_cache_alloc(pgtable_cache[PTE_CACHE_NUM], - GFP_KERNEL|__GFP_REPEAT); -} - -static inline struct page *pte_alloc_one(struct mm_struct *mm, - unsigned long address) -{ - return virt_to_page(pte_alloc_one_kernel(mm, address)); -} - -static inline void pte_free_kernel(pte_t *pte) -{ - kmem_cache_free(pgtable_cache[PTE_CACHE_NUM], pte); -} - -static inline void pte_free(struct page *ptepage) -{ - pte_free_kernel(page_address(ptepage)); -} - -#define PGF_CACHENUM_MASK 0x3 - -typedef struct pgtable_free { - unsigned long val; -} pgtable_free_t; - -static inline pgtable_free_t pgtable_free_cache(void *p, int cachenum, - unsigned long mask) -{ - BUG_ON(cachenum > PGF_CACHENUM_MASK); - - return (pgtable_free_t){.val = ((unsigned long) p & ~mask) | cachenum}; -} - -static inline void pgtable_free(pgtable_free_t pgf) -{ - void *p = (void *)(pgf.val & ~PGF_CACHENUM_MASK); - int cachenum = pgf.val & PGF_CACHENUM_MASK; - - kmem_cache_free(pgtable_cache[cachenum], p); -} - -extern void pgtable_free_tlb(struct mmu_gather *tlb, pgtable_free_t pgf); - -#define __pte_free_tlb(tlb, ptepage) \ - pgtable_free_tlb(tlb, pgtable_free_cache(page_address(ptepage), \ - PTE_CACHE_NUM, PTE_TABLE_SIZE-1)) -#define __pmd_free_tlb(tlb, pmd) \ - pgtable_free_tlb(tlb, pgtable_free_cache(pmd, \ - PMD_CACHE_NUM, PMD_TABLE_SIZE-1)) -#ifndef CONFIG_PPC_64K_PAGES -#define __pud_free_tlb(tlb, pud) \ - pgtable_free_tlb(tlb, pgtable_free_cache(pud, \ - PUD_CACHE_NUM, PUD_TABLE_SIZE-1)) -#endif /* CONFIG_PPC_64K_PAGES */ - -#define check_pgt_cache() do { } while (0) - -#endif /* CONFIG_PPC64 */ #endif /* __KERNEL__ */ #endif /* _ASM_POWERPC_PGALLOC_H */ diff --git a/include/asm-powerpc/pgtable-4k.h b/include/asm-powerpc/pgtable-4k.h index a28fa8bc01d..1744d6ac12a 100644 --- a/include/asm-powerpc/pgtable-4k.h +++ b/include/asm-powerpc/pgtable-4k.h @@ -1,3 +1,5 @@ +#ifndef _ASM_POWERPC_PGTABLE_4K_H +#define _ASM_POWERPC_PGTABLE_4K_H /* * Entries per page directory level. The PTE level must use a 64b record * for each page table entry. The PMD and PGD level use a 32b record for @@ -100,3 +102,4 @@ #define remap_4k_pfn(vma, addr, pfn, prot) \ remap_pfn_range((vma), (addr), (pfn), PAGE_SIZE, (prot)) +#endif /* _ASM_POWERPC_PGTABLE_4K_H */ diff --git a/include/asm-powerpc/pgtable-64k.h b/include/asm-powerpc/pgtable-64k.h index 5e84f070eaf..16ef4978520 100644 --- a/include/asm-powerpc/pgtable-64k.h +++ b/include/asm-powerpc/pgtable-64k.h @@ -1,6 +1,5 @@ #ifndef _ASM_POWERPC_PGTABLE_64K_H #define _ASM_POWERPC_PGTABLE_64K_H -#ifdef __KERNEL__ #include <asm-generic/pgtable-nopud.h> @@ -65,8 +64,6 @@ /* Bits to mask out from a PGD/PUD to get to the PMD page */ #define PUD_MASKED_BITS 0x1ff -#ifndef __ASSEMBLY__ - /* Manipulate "rpte" values */ #define __real_pte(e,p) ((real_pte_t) { \ (e), pte_val(*((p) + PTRS_PER_PTE)) }) @@ -98,6 +95,4 @@ remap_pfn_range((vma), (addr), (pfn), PAGE_SIZE, \ __pgprot(pgprot_val((prot)) | _PAGE_4K_PFN)) -#endif /* __ASSEMBLY__ */ -#endif /* __KERNEL__ */ #endif /* _ASM_POWERPC_PGTABLE_64K_H */ diff --git a/include/asm-powerpc/pgtable-ppc32.h b/include/asm-powerpc/pgtable-ppc32.h new file mode 100644 index 00000000000..e704640b3e4 --- /dev/null +++ b/include/asm-powerpc/pgtable-ppc32.h @@ -0,0 +1,839 @@ +#ifndef _ASM_POWERPC_PGTABLE_PPC32_H +#define _ASM_POWERPC_PGTABLE_PPC32_H + +#include <asm-generic/4level-fixup.h> + +#ifndef __ASSEMBLY__ +#include <linux/sched.h> +#include <linux/threads.h> +#include <asm/processor.h> /* For TASK_SIZE */ +#include <asm/mmu.h> +#include <asm/page.h> +#include <asm/io.h> /* For sub-arch specific PPC_PIN_SIZE */ +struct mm_struct; + +extern unsigned long va_to_phys(unsigned long address); +extern pte_t *va_to_pte(unsigned long address); +extern unsigned long ioremap_bot, ioremap_base; +#endif /* __ASSEMBLY__ */ + +/* + * The PowerPC MMU uses a hash table containing PTEs, together with + * a set of 16 segment registers (on 32-bit implementations), to define + * the virtual to physical address mapping. + * + * We use the hash table as an extended TLB, i.e. a cache of currently + * active mappings. We maintain a two-level page table tree, much + * like that used by the i386, for the sake of the Linux memory + * management code. Low-level assembler code in hashtable.S + * (procedure hash_page) is responsible for extracting ptes from the + * tree and putting them into the hash table when necessary, and + * updating the accessed and modified bits in the page table tree. + */ + +/* + * The PowerPC MPC8xx uses a TLB with hardware assisted, software tablewalk. + * We also use the two level tables, but we can put the real bits in them + * needed for the TLB and tablewalk. These definitions require Mx_CTR.PPM = 0, + * Mx_CTR.PPCS = 0, and MD_CTR.TWAM = 1. The level 2 descriptor has + * additional page protection (when Mx_CTR.PPCS = 1) that allows TLB hit + * based upon user/super access. The TLB does not have accessed nor write + * protect. We assume that if the TLB get loaded with an entry it is + * accessed, and overload the changed bit for write protect. We use + * two bits in the software pte that are supposed to be set to zero in + * the TLB entry (24 and 25) for these indicators. Although the level 1 + * descriptor contains the guarded and writethrough/copyback bits, we can + * set these at the page level since they get copied from the Mx_TWC + * register when the TLB entry is loaded. We will use bit 27 for guard, since + * that is where it exists in the MD_TWC, and bit 26 for writethrough. + * These will get masked from the level 2 descriptor at TLB load time, and + * copied to the MD_TWC before it gets loaded. + * Large page sizes added. We currently support two sizes, 4K and 8M. + * This also allows a TLB hander optimization because we can directly + * load the PMD into MD_TWC. The 8M pages are only used for kernel + * mapping of well known areas. The PMD (PGD) entries contain control + * flags in addition to the address, so care must be taken that the + * software no longer assumes these are only pointers. + */ + +/* + * At present, all PowerPC 400-class processors share a similar TLB + * architecture. The instruction and data sides share a unified, + * 64-entry, fully-associative TLB which is maintained totally under + * software control. In addition, the instruction side has a + * hardware-managed, 4-entry, fully-associative TLB which serves as a + * first level to the shared TLB. These two TLBs are known as the UTLB + * and ITLB, respectively (see "mmu.h" for definitions). + */ + +/* + * The normal case is that PTEs are 32-bits and we have a 1-page + * 1024-entry pgdir pointing to 1-page 1024-entry PTE pages. -- paulus + * + * For any >32-bit physical address platform, we can use the following + * two level page table layout where the pgdir is 8KB and the MS 13 bits + * are an index to the second level table. The combined pgdir/pmd first + * level has 2048 entries and the second level has 512 64-bit PTE entries. + * -Matt + */ +/* PMD_SHIFT determines the size of the area mapped by the PTE pages */ +#define PMD_SHIFT (PAGE_SHIFT + PTE_SHIFT) +#define PMD_SIZE (1UL << PMD_SHIFT) +#define PMD_MASK (~(PMD_SIZE-1)) + +/* PGDIR_SHIFT determines what a top-level page table entry can map */ +#define PGDIR_SHIFT PMD_SHIFT +#define PGDIR_SIZE (1UL << PGDIR_SHIFT) +#define PGDIR_MASK (~(PGDIR_SIZE-1)) + +/* + * entries per page directory level: our page-table tree is two-level, so + * we don't really have any PMD directory. + */ +#define PTRS_PER_PTE (1 << PTE_SHIFT) +#define PTRS_PER_PMD 1 +#define PTRS_PER_PGD (1 << (32 - PGDIR_SHIFT)) + +#define USER_PTRS_PER_PGD (TASK_SIZE / PGDIR_SIZE) +#define FIRST_USER_ADDRESS 0 + +#define USER_PGD_PTRS (PAGE_OFFSET >> PGDIR_SHIFT) +#define KERNEL_PGD_PTRS (PTRS_PER_PGD-USER_PGD_PTRS) + +#define pte_ERROR(e) \ + printk("%s:%d: bad pte %llx.\n", __FILE__, __LINE__, \ + (unsigned long long)pte_val(e)) +#define pmd_ERROR(e) \ + printk("%s:%d: bad pmd %08lx.\n", __FILE__, __LINE__, pmd_val(e)) +#define pgd_ERROR(e) \ + printk("%s:%d: bad pgd %08lx.\n", __FILE__, __LINE__, pgd_val(e)) + +/* + * Just any arbitrary offset to the start of the vmalloc VM area: the + * current 64MB value just means that there will be a 64MB "hole" after the + * physical memory until the kernel virtual memory starts. That means that + * any out-of-bounds memory accesses will hopefully be caught. + * The vmalloc() routines leaves a hole of 4kB between each vmalloced + * area for the same reason. ;) + * + * We no longer map larger than phys RAM with the BATs so we don't have + * to worry about the VMALLOC_OFFSET causing problems. We do have to worry + * about clashes between our early calls to ioremap() that start growing down + * from ioremap_base being run into the VM area allocations (growing upwards + * from VMALLOC_START). For this reason we have ioremap_bot to check when + * we actually run into our mappings setup in the early boot with the VM + * system. This really does become a problem for machines with good amounts + * of RAM. -- Cort + */ +#define VMALLOC_OFFSET (0x1000000) /* 16M */ +#ifdef PPC_PIN_SIZE +#define VMALLOC_START (((_ALIGN((long)high_memory, PPC_PIN_SIZE) + VMALLOC_OFFSET) & ~(VMALLOC_OFFSET-1))) +#else +#define VMALLOC_START ((((long)high_memory + VMALLOC_OFFSET) & ~(VMALLOC_OFFSET-1))) +#endif +#define VMALLOC_END ioremap_bot + +/* + * Bits in a linux-style PTE. These match the bits in the + * (hardware-defined) PowerPC PTE as closely as possible. + */ + +#if defined(CONFIG_40x) + +/* There are several potential gotchas here. The 40x hardware TLBLO + field looks like this: + + 0 1 2 3 4 ... 18 19 20 21 22 23 24 25 26 27 28 29 30 31 + RPN..................... 0 0 EX WR ZSEL....... W I M G + + Where possible we make the Linux PTE bits match up with this + + - bits 20 and 21 must be cleared, because we use 4k pages (40x can + support down to 1k pages), this is done in the TLBMiss exception + handler. + - We use only zones 0 (for kernel pages) and 1 (for user pages) + of the 16 available. Bit 24-26 of the TLB are cleared in the TLB + miss handler. Bit 27 is PAGE_USER, thus selecting the correct + zone. + - PRESENT *must* be in the bottom two bits because swap cache + entries use the top 30 bits. Because 40x doesn't support SMP + anyway, M is irrelevant so we borrow it for PAGE_PRESENT. Bit 30 + is cleared in the TLB miss handler before the TLB entry is loaded. + - All other bits of the PTE are loaded into TLBLO without + modification, leaving us only the bits 20, 21, 24, 25, 26, 30 for + software PTE bits. We actually use use bits 21, 24, 25, and + 30 respectively for the software bits: ACCESSED, DIRTY, RW, and + PRESENT. +*/ + +/* Definitions for 40x embedded chips. */ +#define _PAGE_GUARDED 0x001 /* G: page is guarded from prefetch */ +#define _PAGE_FILE 0x001 /* when !present: nonlinear file mapping */ +#define _PAGE_PRESENT 0x002 /* software: PTE contains a translation */ +#define _PAGE_NO_CACHE 0x004 /* I: caching is inhibited */ +#define _PAGE_WRITETHRU 0x008 /* W: caching is write-through */ +#define _PAGE_USER 0x010 /* matches one of the zone permission bits */ +#define _PAGE_RW 0x040 /* software: Writes permitted */ +#define _PAGE_DIRTY 0x080 /* software: dirty page */ +#define _PAGE_HWWRITE 0x100 /* hardware: Dirty & RW, set in exception */ +#define _PAGE_HWEXEC 0x200 /* hardware: EX permission */ +#define _PAGE_ACCESSED 0x400 /* software: R: page referenced */ + +#define _PMD_PRESENT 0x400 /* PMD points to page of PTEs */ +#define _PMD_BAD 0x802 +#define _PMD_SIZE 0x0e0 /* size field, != 0 for large-page PMD entry */ +#define _PMD_SIZE_4M 0x0c0 +#define _PMD_SIZE_16M 0x0e0 +#define PMD_PAGE_SIZE(pmdval) (1024 << (((pmdval) & _PMD_SIZE) >> 4)) + +#elif defined(CONFIG_44x) +/* + * Definitions for PPC440 + * + * Because of the 3 word TLB entries to support 36-bit addressing, + * the attribute are difficult to map in such a fashion that they + * are easily loaded during exception processing. I decided to + * organize the entry so the ERPN is the only portion in the + * upper word of the PTE and the attribute bits below are packed + * in as sensibly as they can be in the area below a 4KB page size + * oriented RPN. This at least makes it easy to load the RPN and + * ERPN fields in the TLB. -Matt + * + * Note that these bits preclude future use of a page size + * less than 4KB. + * + * + * PPC 440 core has following TLB attribute fields; + * + * TLB1: + * 0 1 2 3 4 ... 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 + * RPN................................. - - - - - - ERPN....... + * + * TLB2: + * 0 1 2 3 4 ... 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 + * - - - - - - U0 U1 U2 U3 W I M G E - UX UW UR SX SW SR + * + * There are some constrains and options, to decide mapping software bits + * into TLB entry. + * + * - PRESENT *must* be in the bottom three bits because swap cache + * entries use the top 29 bits for TLB2. + * + * - FILE *must* be in the bottom three bits because swap cache + * entries use the top 29 bits for TLB2. + * + * - CACHE COHERENT bit (M) has no effect on PPC440 core, because it + * doesn't support SMP. So we can use this as software bit, like + * DIRTY. + * + * With the PPC 44x Linux implementation, the 0-11th LSBs of the PTE are used + * for memory protection related functions (see PTE structure in + * include/asm-ppc/mmu.h). The _PAGE_XXX definitions in this file map to the + * above bits. Note that the bit values are CPU specific, not architecture + * specific. + * + * The kernel PTE entry holds an arch-dependent swp_entry structure under + * certain situations. In other words, in such situations some portion of + * the PTE bits are used as a swp_entry. In the PPC implementation, the + * 3-24th LSB are shared with swp_entry, however the 0-2nd three LSB still + * hold protection values. That means the three protection bits are + * reserved for both PTE and SWAP entry at the most significant three + * LSBs. + * + * There are three protection bits available for SWAP entry: + * _PAGE_PRESENT + * _PAGE_FILE + * _PAGE_HASHPTE (if HW has) + * + * So those three bits have to be inside of 0-2nd LSB of PTE. + * + */ + +#define _PAGE_PRESENT 0x00000001 /* S: PTE valid */ +#define _PAGE_RW 0x00000002 /* S: Write permission */ +#define _PAGE_FILE 0x00000004 /* S: nonlinear file mapping */ +#define _PAGE_ACCESSED 0x00000008 /* S: Page referenced */ +#define _PAGE_HWWRITE 0x00000010 /* H: Dirty & RW */ +#define _PAGE_HWEXEC 0x00000020 /* H: Execute permission */ +#define _PAGE_USER 0x00000040 /* S: User page */ +#define _PAGE_ENDIAN 0x00000080 /* H: E bit */ +#define _PAGE_GUARDED 0x00000100 /* H: G bit */ +#define _PAGE_DIRTY 0x00000200 /* S: Page dirty */ +#define _PAGE_NO_CACHE 0x00000400 /* H: I bit */ +#define _PAGE_WRITETHRU 0x00000800 /* H: W bit */ + +/* TODO: Add large page lowmem mapping support */ +#define _PMD_PRESENT 0 +#define _PMD_PRESENT_MASK (PAGE_MASK) +#define _PMD_BAD (~PAGE_MASK) + +/* ERPN in a PTE never gets cleared, ignore it */ +#define _PTE_NONE_MASK 0xffffffff00000000ULL + +#elif defined(CONFIG_FSL_BOOKE) +/* + MMU Assist Register 3: + + 32 33 34 35 36 ... 50 51 52 53 54 55 56 57 58 59 60 61 62 63 + RPN...................... 0 0 U0 U1 U2 U3 UX SX UW SW UR SR + + - PRESENT *must* be in the bottom three bits because swap cache + entries use the top 29 bits. + + - FILE *must* be in the bottom three bits because swap cache + entries use the top 29 bits. +*/ + +/* Definitions for FSL Book-E Cores */ +#define _PAGE_PRESENT 0x00001 /* S: PTE contains a translation */ +#define _PAGE_USER 0x00002 /* S: User page (maps to UR) */ +#define _PAGE_FILE 0x00002 /* S: when !present: nonlinear file mapping */ +#define _PAGE_ACCESSED 0x00004 /* S: Page referenced */ +#define _PAGE_HWWRITE 0x00008 /* H: Dirty & RW, set in exception */ +#define _PAGE_RW 0x00010 /* S: Write permission */ +#define _PAGE_HWEXEC 0x00020 /* H: UX permission */ + +#define _PAGE_ENDIAN 0x00040 /* H: E bit */ +#define _PAGE_GUARDED 0x00080 /* H: G bit */ +#define _PAGE_COHERENT 0x00100 /* H: M bit */ +#define _PAGE_NO_CACHE 0x00200 /* H: I bit */ +#define _PAGE_WRITETHRU 0x00400 /* H: W bit */ + +#ifdef CONFIG_PTE_64BIT +#define _PAGE_DIRTY 0x08000 /* S: Page dirty */ + +/* ERPN in a PTE never gets cleared, ignore it */ +#define _PTE_NONE_MASK 0xffffffffffff0000ULL +#else +#define _PAGE_DIRTY 0x00800 /* S: Page dirty */ +#endif + +#define _PMD_PRESENT 0 +#define _PMD_PRESENT_MASK (PAGE_MASK) +#define _PMD_BAD (~PAGE_MASK) + +#elif defined(CONFIG_8xx) +/* Definitions for 8xx embedded chips. */ +#define _PAGE_PRESENT 0x0001 /* Page is valid */ +#define _PAGE_FILE 0x0002 /* when !present: nonlinear file mapping */ +#define _PAGE_NO_CACHE 0x0002 /* I: cache inhibit */ +#define _PAGE_SHARED 0x0004 /* No ASID (context) compare */ + +/* These five software bits must be masked out when the entry is loaded + * into the TLB. + */ +#define _PAGE_EXEC 0x0008 /* software: i-cache coherency required */ +#define _PAGE_GUARDED 0x0010 /* software: guarded access */ +#define _PAGE_DIRTY 0x0020 /* software: page changed */ +#define _PAGE_RW 0x0040 /* software: user write access allowed */ +#define _PAGE_ACCESSED 0x0080 /* software: page referenced */ + +/* Setting any bits in the nibble with the follow two controls will + * require a TLB exception handler change. It is assumed unused bits + * are always zero. + */ +#define _PAGE_HWWRITE 0x0100 /* h/w write enable: never set in Linux PTE */ +#define _PAGE_USER 0x0800 /* One of the PP bits, the other is USER&~RW */ + +#define _PMD_PRESENT 0x0001 +#define _PMD_BAD 0x0ff0 +#define _PMD_PAGE_MASK 0x000c +#define _PMD_PAGE_8M 0x000c + +/* + * The 8xx TLB miss handler allegedly sets _PAGE_ACCESSED in the PTE + * for an address even if _PAGE_PRESENT is not set, as a performance + * optimization. This is a bug if you ever want to use swap unless + * _PAGE_ACCESSED is 2, which it isn't, or unless you have 8xx-specific + * definitions for __swp_entry etc. below, which would be gross. + * -- paulus + */ +#define _PTE_NONE_MASK _PAGE_ACCESSED + +#else /* CONFIG_6xx */ +/* Definitions for 60x, 740/750, etc. */ +#define _PAGE_PRESENT 0x001 /* software: pte contains a translation */ +#define _PAGE_HASHPTE 0x002 /* hash_page has made an HPTE for this pte */ +#define _PAGE_FILE 0x004 /* when !present: nonlinear file mapping */ +#define _PAGE_USER 0x004 /* usermode access allowed */ +#define _PAGE_GUARDED 0x008 /* G: prohibit speculative access */ +#define _PAGE_COHERENT 0x010 /* M: enforce memory coherence (SMP systems) */ +#define _PAGE_NO_CACHE 0x020 /* I: cache inhibit */ +#define _PAGE_WRITETHRU 0x040 /* W: cache write-through */ +#define _PAGE_DIRTY 0x080 /* C: page changed */ +#define _PAGE_ACCESSED 0x100 /* R: page referenced */ +#define _PAGE_EXEC 0x200 /* software: i-cache coherency required */ +#define _PAGE_RW 0x400 /* software: user write access allowed */ + +#define _PTE_NONE_MASK _PAGE_HASHPTE + +#define _PMD_PRESENT 0 +#define _PMD_PRESENT_MASK (PAGE_MASK) +#define _PMD_BAD (~PAGE_MASK) +#endif + +/* + * Some bits are only used on some cpu families... + */ +#ifndef _PAGE_HASHPTE +#define _PAGE_HASHPTE 0 +#endif +#ifndef _PTE_NONE_MASK +#define _PTE_NONE_MASK 0 +#endif +#ifndef _PAGE_SHARED +#define _PAGE_SHARED 0 +#endif +#ifndef _PAGE_HWWRITE +#define _PAGE_HWWRITE 0 +#endif +#ifndef _PAGE_HWEXEC +#define _PAGE_HWEXEC 0 +#endif +#ifndef _PAGE_EXEC +#define _PAGE_EXEC 0 +#endif +#ifndef _PMD_PRESENT_MASK +#define _PMD_PRESENT_MASK _PMD_PRESENT +#endif +#ifndef _PMD_SIZE +#define _PMD_SIZE 0 +#define PMD_PAGE_SIZE(pmd) bad_call_to_PMD_PAGE_SIZE() +#endif + +#define _PAGE_CHG_MASK (PAGE_MASK | _PAGE_ACCESSED | _PAGE_DIRTY) + +/* + * Note: the _PAGE_COHERENT bit automatically gets set in the hardware + * PTE if CONFIG_SMP is defined (hash_page does this); there is no need + * to have it in the Linux PTE, and in fact the bit could be reused for + * another purpose. -- paulus. + */ + +#ifdef CONFIG_44x +#define _PAGE_BASE (_PAGE_PRESENT | _PAGE_ACCESSED | _PAGE_GUARDED) +#else +#define _PAGE_BASE (_PAGE_PRESENT | _PAGE_ACCESSED) +#endif +#define _PAGE_WRENABLE (_PAGE_RW | _PAGE_DIRTY | _PAGE_HWWRITE) +#define _PAGE_KERNEL (_PAGE_BASE | _PAGE_SHARED | _PAGE_WRENABLE) + +#ifdef CONFIG_PPC_STD_MMU +/* On standard PPC MMU, no user access implies kernel read/write access, + * so to write-protect kernel memory we must turn on user access */ +#define _PAGE_KERNEL_RO (_PAGE_BASE | _PAGE_SHARED | _PAGE_USER) +#else +#define _PAGE_KERNEL_RO (_PAGE_BASE | _PAGE_SHARED) +#endif + +#define _PAGE_IO (_PAGE_KERNEL | _PAGE_NO_CACHE | _PAGE_GUARDED) +#define _PAGE_RAM (_PAGE_KERNEL | _PAGE_HWEXEC) + +#if defined(CONFIG_KGDB) || defined(CONFIG_XMON) || defined(CONFIG_BDI_SWITCH) +/* We want the debuggers to be able to set breakpoints anywhere, so + * don't write protect the kernel text */ +#define _PAGE_RAM_TEXT _PAGE_RAM +#else +#define _PAGE_RAM_TEXT (_PAGE_KERNEL_RO | _PAGE_HWEXEC) +#endif + +#define PAGE_NONE __pgprot(_PAGE_BASE) +#define PAGE_READONLY __pgprot(_PAGE_BASE | _PAGE_USER) +#define PAGE_READONLY_X __pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_EXEC) +#define PAGE_SHARED __pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_RW) +#define PAGE_SHARED_X __pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_RW | _PAGE_EXEC) +#define PAGE_COPY __pgprot(_PAGE_BASE | _PAGE_USER) +#define PAGE_COPY_X __pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_EXEC) + +#define PAGE_KERNEL __pgprot(_PAGE_RAM) +#define PAGE_KERNEL_NOCACHE __pgprot(_PAGE_IO) + +/* + * The PowerPC can only do execute protection on a segment (256MB) basis, + * not on a page basis. So we consider execute permission the same as read. + * Also, write permissions imply read permissions. + * This is the closest we can get.. + */ +#define __P000 PAGE_NONE +#define __P001 PAGE_READONLY_X +#define __P010 PAGE_COPY +#define __P011 PAGE_COPY_X +#define __P100 PAGE_READONLY +#define __P101 PAGE_READONLY_X +#define __P110 PAGE_COPY +#define __P111 PAGE_COPY_X + +#define __S000 PAGE_NONE +#define __S001 PAGE_READONLY_X +#define __S010 PAGE_SHARED +#define __S011 PAGE_SHARED_X +#define __S100 PAGE_READONLY +#define __S101 PAGE_READONLY_X +#define __S110 PAGE_SHARED +#define __S111 PAGE_SHARED_X + +#ifndef __ASSEMBLY__ +/* Make sure we get a link error if PMD_PAGE_SIZE is ever called on a + * kernel without large page PMD support */ +extern unsigned long bad_call_to_PMD_PAGE_SIZE(void); + +/* + * Conversions between PTE values and page frame numbers. + */ + +/* in some case we want to additionaly adjust where the pfn is in the pte to + * allow room for more flags */ +#if defined(CONFIG_FSL_BOOKE) && defined(CONFIG_PTE_64BIT) +#define PFN_SHIFT_OFFSET (PAGE_SHIFT + 8) +#else +#define PFN_SHIFT_OFFSET (PAGE_SHIFT) +#endif + +#define pte_pfn(x) (pte_val(x) >> PFN_SHIFT_OFFSET) +#define pte_page(x) pfn_to_page(pte_pfn(x)) + +#define pfn_pte(pfn, prot) __pte(((pte_basic_t)(pfn) << PFN_SHIFT_OFFSET) |\ + pgprot_val(prot)) +#define mk_pte(page, prot) pfn_pte(page_to_pfn(page), prot) + +/* + * ZERO_PAGE is a global shared page that is always zero: used + * for zero-mapped memory areas etc.. + */ +extern unsigned long empty_zero_page[1024]; +#define ZERO_PAGE(vaddr) (virt_to_page(empty_zero_page)) + +#endif /* __ASSEMBLY__ */ + +#define pte_none(pte) ((pte_val(pte) & ~_PTE_NONE_MASK) == 0) +#define pte_present(pte) (pte_val(pte) & _PAGE_PRESENT) +#define pte_clear(mm,addr,ptep) do { set_pte_at((mm), (addr), (ptep), __pte(0)); } while (0) + +#define pmd_none(pmd) (!pmd_val(pmd)) +#define pmd_bad(pmd) (pmd_val(pmd) & _PMD_BAD) +#define pmd_present(pmd) (pmd_val(pmd) & _PMD_PRESENT_MASK) +#define pmd_clear(pmdp) do { pmd_val(*(pmdp)) = 0; } while (0) + +#ifndef __ASSEMBLY__ +/* + * The "pgd_xxx()" functions here are trivial for a folded two-level + * setup: the pgd is never bad, and a pmd always exists (as it's folded + * into the pgd entry) + */ +static inline int pgd_none(pgd_t pgd) { return 0; } +static inline int pgd_bad(pgd_t pgd) { return 0; } +static inline int pgd_present(pgd_t pgd) { return 1; } +#define pgd_clear(xp) do { } while (0) + +#define pgd_page_vaddr(pgd) \ + ((unsigned long) __va(pgd_val(pgd) & PAGE_MASK)) + +/* + * The following only work if pte_present() is true. + * Undefined behaviour if not.. + */ +static inline int pte_read(pte_t pte) { return pte_val(pte) & _PAGE_USER; } +static inline int pte_write(pte_t pte) { return pte_val(pte) & _PAGE_RW; } +static inline int pte_exec(pte_t pte) { return pte_val(pte) & _PAGE_EXEC; } +static inline int pte_dirty(pte_t pte) { return pte_val(pte) & _PAGE_DIRTY; } +static inline int pte_young(pte_t pte) { return pte_val(pte) & _PAGE_ACCESSED; } +static inline int pte_file(pte_t pte) { return pte_val(pte) & _PAGE_FILE; } + +static inline void pte_uncache(pte_t pte) { pte_val(pte) |= _PAGE_NO_CACHE; } +static inline void pte_cache(pte_t pte) { pte_val(pte) &= ~_PAGE_NO_CACHE; } + +static inline pte_t pte_rdprotect(pte_t pte) { + pte_val(pte) &= ~_PAGE_USER; return pte; } +static inline pte_t pte_wrprotect(pte_t pte) { + pte_val(pte) &= ~(_PAGE_RW | _PAGE_HWWRITE); return pte; } +static inline pte_t pte_exprotect(pte_t pte) { + pte_val(pte) &= ~_PAGE_EXEC; return pte; } +static inline pte_t pte_mkclean(pte_t pte) { + pte_val(pte) &= ~(_PAGE_DIRTY | _PAGE_HWWRITE); return pte; } +static inline pte_t pte_mkold(pte_t pte) { + pte_val(pte) &= ~_PAGE_ACCESSED; return pte; } + +static inline pte_t pte_mkread(pte_t pte) { + pte_val(pte) |= _PAGE_USER; return pte; } +static inline pte_t pte_mkexec(pte_t pte) { + pte_val(pte) |= _PAGE_USER | _PAGE_EXEC; return pte; } +static inline pte_t pte_mkwrite(pte_t pte) { + pte_val(pte) |= _PAGE_RW; return pte; } +static inline pte_t pte_mkdirty(pte_t pte) { + pte_val(pte) |= _PAGE_DIRTY; return pte; } +static inline pte_t pte_mkyoung(pte_t pte) { + pte_val(pte) |= _PAGE_ACCESSED; return pte; } + +static inline pte_t pte_modify(pte_t pte, pgprot_t newprot) +{ + pte_val(pte) = (pte_val(pte) & _PAGE_CHG_MASK) | pgprot_val(newprot); + return pte; +} + +/* + * When flushing the tlb entry for a page, we also need to flush the hash + * table entry. flush_hash_pages is assembler (for speed) in hashtable.S. + */ +extern int flush_hash_pages(unsigned context, unsigned long va, + unsigned long pmdval, int count); + +/* Add an HPTE to the hash table */ +extern void add_hash_page(unsigned context, unsigned long va, + unsigned long pmdval); + +/* + * Atomic PTE updates. + * + * pte_update clears and sets bit atomically, and returns + * the old pte value. In the 64-bit PTE case we lock around the + * low PTE word since we expect ALL flag bits to be there + */ +#ifndef CONFIG_PTE_64BIT +static inline unsigned long pte_update(pte_t *p, unsigned long clr, + unsigned long set) +{ + unsigned long old, tmp; + + __asm__ __volatile__("\ +1: lwarx %0,0,%3\n\ + andc %1,%0,%4\n\ + or %1,%1,%5\n" + PPC405_ERR77(0,%3) +" stwcx. %1,0,%3\n\ + bne- 1b" + : "=&r" (old), "=&r" (tmp), "=m" (*p) + : "r" (p), "r" (clr), "r" (set), "m" (*p) + : "cc" ); + return old; +} +#else +static inline unsigned long long pte_update(pte_t *p, unsigned long clr, + unsigned long set) +{ + unsigned long long old; + unsigned long tmp; + + __asm__ __volatile__("\ +1: lwarx %L0,0,%4\n\ + lwzx %0,0,%3\n\ + andc %1,%L0,%5\n\ + or %1,%1,%6\n" + PPC405_ERR77(0,%3) +" stwcx. %1,0,%4\n\ + bne- 1b" + : "=&r" (old), "=&r" (tmp), "=m" (*p) + : "r" (p), "r" ((unsigned long)(p) + 4), "r" (clr), "r" (set), "m" (*p) + : "cc" ); + return old; +} +#endif + +/* + * set_pte stores a linux PTE into the linux page table. + * On machines which use an MMU hash table we avoid changing the + * _PAGE_HASHPTE bit. + */ +static inline void set_pte_at(struct mm_struct *mm, unsigned long addr, + pte_t *ptep, pte_t pte) +{ +#if _PAGE_HASHPTE != 0 + pte_update(ptep, ~_PAGE_HASHPTE, pte_val(pte) & ~_PAGE_HASHPTE); +#else + *ptep = pte; +#endif +} + +/* + * 2.6 calles this without flushing the TLB entry, this is wrong + * for our hash-based implementation, we fix that up here + */ +#define __HAVE_ARCH_PTEP_TEST_AND_CLEAR_YOUNG +static inline int __ptep_test_and_clear_young(unsigned int context, unsigned long addr, pte_t *ptep) +{ + unsigned long old; + old = pte_update(ptep, _PAGE_ACCESSED, 0); +#if _PAGE_HASHPTE != 0 + if (old & _PAGE_HASHPTE) { + unsigned long ptephys = __pa(ptep) & PAGE_MASK; + flush_hash_pages(context, addr, ptephys, 1); + } +#endif + return (old & _PAGE_ACCESSED) != 0; +} +#define ptep_test_and_clear_young(__vma, __addr, __ptep) \ + __ptep_test_and_clear_young((__vma)->vm_mm->context.id, __addr, __ptep) + +#define __HAVE_ARCH_PTEP_TEST_AND_CLEAR_DIRTY +static inline int ptep_test_and_clear_dirty(struct vm_area_struct *vma, + unsigned long addr, pte_t *ptep) +{ + return (pte_update(ptep, (_PAGE_DIRTY | _PAGE_HWWRITE), 0) & _PAGE_DIRTY) != 0; +} + +#define __HAVE_ARCH_PTEP_GET_AND_CLEAR +static inline pte_t ptep_get_and_clear(struct mm_struct *mm, unsigned long addr, + pte_t *ptep) +{ + return __pte(pte_update(ptep, ~_PAGE_HASHPTE, 0)); +} + +#define __HAVE_ARCH_PTEP_SET_WRPROTECT +static inline void ptep_set_wrprotect(struct mm_struct *mm, unsigned long addr, + pte_t *ptep) +{ + pte_update(ptep, (_PAGE_RW | _PAGE_HWWRITE), 0); +} + +#define __HAVE_ARCH_PTEP_SET_ACCESS_FLAGS +static inline void __ptep_set_access_flags(pte_t *ptep, pte_t entry, int dirty) +{ + unsigned long bits = pte_val(entry) & + (_PAGE_DIRTY | _PAGE_ACCESSED | _PAGE_RW); + pte_update(ptep, 0, bits); +} + +#define ptep_set_access_flags(__vma, __address, __ptep, __entry, __dirty) \ + do { \ + __ptep_set_access_flags(__ptep, __entry, __dirty); \ + flush_tlb_page_nohash(__vma, __address); \ + } while(0) + +/* + * Macro to mark a page protection value as "uncacheable". + */ +#define pgprot_noncached(prot) (__pgprot(pgprot_val(prot) | _PAGE_NO_CACHE | _PAGE_GUARDED)) + +struct file; +extern pgprot_t phys_mem_access_prot(struct file *file, unsigned long pfn, + unsigned long size, pgprot_t vma_prot); +#define __HAVE_PHYS_MEM_ACCESS_PROT + +#define __HAVE_ARCH_PTE_SAME +#define pte_same(A,B) (((pte_val(A) ^ pte_val(B)) & ~_PAGE_HASHPTE) == 0) + +/* + * Note that on Book E processors, the pmd contains the kernel virtual + * (lowmem) address of the pte page. The physical address is less useful + * because everything runs with translation enabled (even the TLB miss + * handler). On everything else the pmd contains the physical address + * of the pte page. -- paulus + */ +#ifndef CONFIG_BOOKE +#define pmd_page_vaddr(pmd) \ + ((unsigned long) __va(pmd_val(pmd) & PAGE_MASK)) +#define pmd_page(pmd) \ + (mem_map + (pmd_val(pmd) >> PAGE_SHIFT)) +#else +#define pmd_page_vaddr(pmd) \ + ((unsigned long) (pmd_val(pmd) & PAGE_MASK)) +#define pmd_page(pmd) \ + (mem_map + (__pa(pmd_val(pmd)) >> PAGE_SHIFT)) +#endif + +/* to find an entry in a kernel page-table-directory */ +#define pgd_offset_k(address) pgd_offset(&init_mm, address) + +/* to find an entry in a page-table-directory */ +#define pgd_index(address) ((address) >> PGDIR_SHIFT) +#define pgd_offset(mm, address) ((mm)->pgd + pgd_index(address)) + +/* Find an entry in the second-level page table.. */ +static inline pmd_t * pmd_offset(pgd_t * dir, unsigned long address) +{ + return (pmd_t *) dir; +} + +/* Find an entry in the third-level page table.. */ +#define pte_index(address) \ + (((address) >> PAGE_SHIFT) & (PTRS_PER_PTE - 1)) +#define pte_offset_kernel(dir, addr) \ + ((pte_t *) pmd_page_vaddr(*(dir)) + pte_index(addr)) +#define pte_offset_map(dir, addr) \ + ((pte_t *) kmap_atomic(pmd_page(*(dir)), KM_PTE0) + pte_index(addr)) +#define pte_offset_map_nested(dir, addr) \ + ((pte_t *) kmap_atomic(pmd_page(*(dir)), KM_PTE1) + pte_index(addr)) + +#define pte_unmap(pte) kunmap_atomic(pte, KM_PTE0) +#define pte_unmap_nested(pte) kunmap_atomic(pte, KM_PTE1) + +extern pgd_t swapper_pg_dir[PTRS_PER_PGD]; + +extern void paging_init(void); + +/* + * Encode and decode a swap entry. + * Note that the bits we use in a PTE for representing a swap entry + * must not include the _PAGE_PRESENT bit, the _PAGE_FILE bit, or the + *_PAGE_HASHPTE bit (if used). -- paulus + */ +#define __swp_type(entry) ((entry).val & 0x1f) +#define __swp_offset(entry) ((entry).val >> 5) +#define __swp_entry(type, offset) ((swp_entry_t) { (type) | ((offset) << 5) }) +#define __pte_to_swp_entry(pte) ((swp_entry_t) { pte_val(pte) >> 3 }) +#define __swp_entry_to_pte(x) ((pte_t) { (x).val << 3 }) + +/* Encode and decode a nonlinear file mapping entry */ +#define PTE_FILE_MAX_BITS 29 +#define pte_to_pgoff(pte) (pte_val(pte) >> 3) +#define pgoff_to_pte(off) ((pte_t) { ((off) << 3) | _PAGE_FILE }) + +/* CONFIG_APUS */ +/* For virtual address to physical address conversion */ +extern void cache_clear(__u32 addr, int length); +extern void cache_push(__u32 addr, int length); +extern int mm_end_of_chunk (unsigned long addr, int len); +extern unsigned long iopa(unsigned long addr); +extern unsigned long mm_ptov(unsigned long addr) __attribute_const__; + +/* Values for nocacheflag and cmode */ +/* These are not used by the APUS kernel_map, but prevents + compilation errors. */ +#define KERNELMAP_FULL_CACHING 0 +#define KERNELMAP_NOCACHE_SER 1 +#define KERNELMAP_NOCACHE_NONSER 2 +#define KERNELMAP_NO_COPYBACK 3 + +/* + * Map some physical address range into the kernel address space. + */ +extern unsigned long kernel_map(unsigned long paddr, unsigned long size, + int nocacheflag, unsigned long *memavailp ); + +/* + * Set cache mode of (kernel space) address range. + */ +extern void kernel_set_cachemode (unsigned long address, unsigned long size, + unsigned int cmode); + +/* Needs to be defined here and not in linux/mm.h, as it is arch dependent */ +#define kern_addr_valid(addr) (1) + +#ifdef CONFIG_PHYS_64BIT +extern int remap_pfn_range(struct vm_area_struct *vma, unsigned long from, + unsigned long paddr, unsigned long size, pgprot_t prot); + +static inline int io_remap_pfn_range(struct vm_area_struct *vma, + unsigned long vaddr, + unsigned long pfn, + unsigned long size, + pgprot_t prot) +{ + phys_addr_t paddr64 = fixup_bigphys_addr(pfn << PAGE_SHIFT, size); + return remap_pfn_range(vma, vaddr, paddr64 >> PAGE_SHIFT, size, prot); +} +#else +#define io_remap_pfn_range(vma, vaddr, pfn, size, prot) \ + remap_pfn_range(vma, vaddr, pfn, size, prot) +#endif + +/* + * No page table caches to initialise + */ +#define pgtable_cache_init() do { } while (0) + +extern int get_pteptr(struct mm_struct *mm, unsigned long addr, pte_t **ptep, + pmd_t **pmdp); + +#endif /* !__ASSEMBLY__ */ + +#endif /* _ASM_POWERPC_PGTABLE_PPC32_H */ diff --git a/include/asm-powerpc/pgtable-ppc64.h b/include/asm-powerpc/pgtable-ppc64.h new file mode 100644 index 00000000000..704c4e669fe --- /dev/null +++ b/include/asm-powerpc/pgtable-ppc64.h @@ -0,0 +1,492 @@ +#ifndef _ASM_POWERPC_PGTABLE_PPC64_H_ +#define _ASM_POWERPC_PGTABLE_PPC64_H_ +/* + * This file contains the functions and defines necessary to modify and use + * the ppc64 hashed page table. + */ + +#ifndef __ASSEMBLY__ +#include <linux/stddef.h> +#include <asm/processor.h> /* For TASK_SIZE */ +#include <asm/mmu.h> +#include <asm/page.h> +#include <asm/tlbflush.h> +struct mm_struct; +#endif /* __ASSEMBLY__ */ + +#ifdef CONFIG_PPC_64K_PAGES +#include <asm/pgtable-64k.h> +#else +#include <asm/pgtable-4k.h> +#endif + +#define FIRST_USER_ADDRESS 0 + +/* + * Size of EA range mapped by our pagetables. + */ +#define PGTABLE_EADDR_SIZE (PTE_INDEX_SIZE + PMD_INDEX_SIZE + \ + PUD_INDEX_SIZE + PGD_INDEX_SIZE + PAGE_SHIFT) +#define PGTABLE_RANGE (1UL << PGTABLE_EADDR_SIZE) + +#if TASK_SIZE_USER64 > PGTABLE_RANGE +#error TASK_SIZE_USER64 exceeds pagetable range +#endif + +#if TASK_SIZE_USER64 > (1UL << (USER_ESID_BITS + SID_SHIFT)) +#error TASK_SIZE_USER64 exceeds user VSID range +#endif + +/* + * Define the address range of the vmalloc VM area. + */ +#define VMALLOC_START ASM_CONST(0xD000000000000000) +#define VMALLOC_SIZE ASM_CONST(0x80000000000) +#define VMALLOC_END (VMALLOC_START + VMALLOC_SIZE) + +/* + * Define the address range of the imalloc VM area. + */ +#define PHBS_IO_BASE VMALLOC_END +#define IMALLOC_BASE (PHBS_IO_BASE + 0x80000000ul) /* Reserve 2 gigs for PHBs */ +#define IMALLOC_END (VMALLOC_START + PGTABLE_RANGE) + +/* + * Region IDs + */ +#define REGION_SHIFT 60UL +#define REGION_MASK (0xfUL << REGION_SHIFT) +#define REGION_ID(ea) (((unsigned long)(ea)) >> REGION_SHIFT) + +#define VMALLOC_REGION_ID (REGION_ID(VMALLOC_START)) +#define KERNEL_REGION_ID (REGION_ID(PAGE_OFFSET)) +#define USER_REGION_ID (0UL) + +/* + * Common bits in a linux-style PTE. These match the bits in the + * (hardware-defined) PowerPC PTE as closely as possible. Additional + * bits may be defined in pgtable-*.h + */ +#define _PAGE_PRESENT 0x0001 /* software: pte contains a translation */ +#define _PAGE_USER 0x0002 /* matches one of the PP bits */ +#define _PAGE_FILE 0x0002 /* (!present only) software: pte holds file offset */ +#define _PAGE_EXEC 0x0004 /* No execute on POWER4 and newer (we invert) */ +#define _PAGE_GUARDED 0x0008 +#define _PAGE_COHERENT 0x0010 /* M: enforce memory coherence (SMP systems) */ +#define _PAGE_NO_CACHE 0x0020 /* I: cache inhibit */ +#define _PAGE_WRITETHRU 0x0040 /* W: cache write-through */ +#define _PAGE_DIRTY 0x0080 /* C: page changed */ +#define _PAGE_ACCESSED 0x0100 /* R: page referenced */ +#define _PAGE_RW 0x0200 /* software: user write access allowed */ +#define _PAGE_HASHPTE 0x0400 /* software: pte has an associated HPTE */ +#define _PAGE_BUSY 0x0800 /* software: PTE & hash are busy */ + +#define _PAGE_BASE (_PAGE_PRESENT | _PAGE_ACCESSED | _PAGE_COHERENT) + +#define _PAGE_WRENABLE (_PAGE_RW | _PAGE_DIRTY) + +/* __pgprot defined in asm-powerpc/page.h */ +#define PAGE_NONE __pgprot(_PAGE_PRESENT | _PAGE_ACCESSED) + +#define PAGE_SHARED __pgprot(_PAGE_BASE | _PAGE_RW | _PAGE_USER) +#define PAGE_SHARED_X __pgprot(_PAGE_BASE | _PAGE_RW | _PAGE_USER | _PAGE_EXEC) +#define PAGE_COPY __pgprot(_PAGE_BASE | _PAGE_USER) +#define PAGE_COPY_X __pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_EXEC) +#define PAGE_READONLY __pgprot(_PAGE_BASE | _PAGE_USER) +#define PAGE_READONLY_X __pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_EXEC) +#define PAGE_KERNEL __pgprot(_PAGE_BASE | _PAGE_WRENABLE) +#define PAGE_KERNEL_CI __pgprot(_PAGE_PRESENT | _PAGE_ACCESSED | \ + _PAGE_WRENABLE | _PAGE_NO_CACHE | _PAGE_GUARDED) +#define PAGE_KERNEL_EXEC __pgprot(_PAGE_BASE | _PAGE_WRENABLE | _PAGE_EXEC) + +#define PAGE_AGP __pgprot(_PAGE_BASE | _PAGE_WRENABLE | _PAGE_NO_CACHE) +#define HAVE_PAGE_AGP + +/* PTEIDX nibble */ +#define _PTEIDX_SECONDARY 0x8 +#define _PTEIDX_GROUP_IX 0x7 + + +/* + * POWER4 and newer have per page execute protection, older chips can only + * do this on a segment (256MB) basis. + * + * Also, write permissions imply read permissions. + * This is the closest we can get.. + * + * Note due to the way vm flags are laid out, the bits are XWR + */ +#define __P000 PAGE_NONE +#define __P001 PAGE_READONLY +#define __P010 PAGE_COPY +#define __P011 PAGE_COPY +#define __P100 PAGE_READONLY_X +#define __P101 PAGE_READONLY_X +#define __P110 PAGE_COPY_X +#define __P111 PAGE_COPY_X + +#define __S000 PAGE_NONE +#define __S001 PAGE_READONLY +#define __S010 PAGE_SHARED +#define __S011 PAGE_SHARED +#define __S100 PAGE_READONLY_X +#define __S101 PAGE_READONLY_X +#define __S110 PAGE_SHARED_X +#define __S111 PAGE_SHARED_X + +#ifndef __ASSEMBLY__ + +/* + * ZERO_PAGE is a global shared page that is always zero: used + * for zero-mapped memory areas etc.. + */ +extern unsigned long empty_zero_page[PAGE_SIZE/sizeof(unsigned long)]; +#define ZERO_PAGE(vaddr) (virt_to_page(empty_zero_page)) +#endif /* __ASSEMBLY__ */ + +#ifdef CONFIG_HUGETLB_PAGE + +#define HAVE_ARCH_UNMAPPED_AREA +#define HAVE_ARCH_UNMAPPED_AREA_TOPDOWN + +#endif + +#ifndef __ASSEMBLY__ + +/* + * Conversion functions: convert a page and protection to a page entry, + * and a page entry and page directory to the page they refer to. + * + * mk_pte takes a (struct page *) as input + */ +#define mk_pte(page, pgprot) pfn_pte(page_to_pfn(page), (pgprot)) + +static inline pte_t pfn_pte(unsigned long pfn, pgprot_t pgprot) +{ + pte_t pte; + + + pte_val(pte) = (pfn << PTE_RPN_SHIFT) | pgprot_val(pgprot); + return pte; +} + +#define pte_modify(_pte, newprot) \ + (__pte((pte_val(_pte) & _PAGE_CHG_MASK) | pgprot_val(newprot))) + +#define pte_none(pte) ((pte_val(pte) & ~_PAGE_HPTEFLAGS) == 0) +#define pte_present(pte) (pte_val(pte) & _PAGE_PRESENT) + +/* pte_clear moved to later in this file */ + +#define pte_pfn(x) ((unsigned long)((pte_val(x)>>PTE_RPN_SHIFT))) +#define pte_page(x) pfn_to_page(pte_pfn(x)) + +#define PMD_BAD_BITS (PTE_TABLE_SIZE-1) +#define PUD_BAD_BITS (PMD_TABLE_SIZE-1) + +#define pmd_set(pmdp, pmdval) (pmd_val(*(pmdp)) = (pmdval)) +#define pmd_none(pmd) (!pmd_val(pmd)) +#define pmd_bad(pmd) (!is_kernel_addr(pmd_val(pmd)) \ + || (pmd_val(pmd) & PMD_BAD_BITS)) +#define pmd_present(pmd) (pmd_val(pmd) != 0) +#define pmd_clear(pmdp) (pmd_val(*(pmdp)) = 0) +#define pmd_page_vaddr(pmd) (pmd_val(pmd) & ~PMD_MASKED_BITS) +#define pmd_page(pmd) virt_to_page(pmd_page_vaddr(pmd)) + +#define pud_set(pudp, pudval) (pud_val(*(pudp)) = (pudval)) +#define pud_none(pud) (!pud_val(pud)) +#define pud_bad(pud) (!is_kernel_addr(pud_val(pud)) \ + || (pud_val(pud) & PUD_BAD_BITS)) +#define pud_present(pud) (pud_val(pud) != 0) +#define pud_clear(pudp) (pud_val(*(pudp)) = 0) +#define pud_page_vaddr(pud) (pud_val(pud) & ~PUD_MASKED_BITS) +#define pud_page(pud) virt_to_page(pud_page_vaddr(pud)) + +#define pgd_set(pgdp, pudp) ({pgd_val(*(pgdp)) = (unsigned long)(pudp);}) + +/* + * Find an entry in a page-table-directory. We combine the address region + * (the high order N bits) and the pgd portion of the address. + */ +/* to avoid overflow in free_pgtables we don't use PTRS_PER_PGD here */ +#define pgd_index(address) (((address) >> (PGDIR_SHIFT)) & 0x1ff) + +#define pgd_offset(mm, address) ((mm)->pgd + pgd_index(address)) + +#define pmd_offset(pudp,addr) \ + (((pmd_t *) pud_page_vaddr(*(pudp))) + (((addr) >> PMD_SHIFT) & (PTRS_PER_PMD - 1))) + +#define pte_offset_kernel(dir,addr) \ + (((pte_t *) pmd_page_vaddr(*(dir))) + (((addr) >> PAGE_SHIFT) & (PTRS_PER_PTE - 1))) + +#define pte_offset_map(dir,addr) pte_offset_kernel((dir), (addr)) +#define pte_offset_map_nested(dir,addr) pte_offset_kernel((dir), (addr)) +#define pte_unmap(pte) do { } while(0) +#define pte_unmap_nested(pte) do { } while(0) + +/* to find an entry in a kernel page-table-directory */ +/* This now only contains the vmalloc pages */ +#define pgd_offset_k(address) pgd_offset(&init_mm, address) + +/* + * The following only work if pte_present() is true. + * Undefined behaviour if not.. + */ +static inline int pte_read(pte_t pte) { return pte_val(pte) & _PAGE_USER;} +static inline int pte_write(pte_t pte) { return pte_val(pte) & _PAGE_RW;} +static inline int pte_exec(pte_t pte) { return pte_val(pte) & _PAGE_EXEC;} +static inline int pte_dirty(pte_t pte) { return pte_val(pte) & _PAGE_DIRTY;} +static inline int pte_young(pte_t pte) { return pte_val(pte) & _PAGE_ACCESSED;} +static inline int pte_file(pte_t pte) { return pte_val(pte) & _PAGE_FILE;} + +static inline void pte_uncache(pte_t pte) { pte_val(pte) |= _PAGE_NO_CACHE; } +static inline void pte_cache(pte_t pte) { pte_val(pte) &= ~_PAGE_NO_CACHE; } + +static inline pte_t pte_rdprotect(pte_t pte) { + pte_val(pte) &= ~_PAGE_USER; return pte; } +static inline pte_t pte_exprotect(pte_t pte) { + pte_val(pte) &= ~_PAGE_EXEC; return pte; } +static inline pte_t pte_wrprotect(pte_t pte) { + pte_val(pte) &= ~(_PAGE_RW); return pte; } +static inline pte_t pte_mkclean(pte_t pte) { + pte_val(pte) &= ~(_PAGE_DIRTY); return pte; } +static inline pte_t pte_mkold(pte_t pte) { + pte_val(pte) &= ~_PAGE_ACCESSED; return pte; } +static inline pte_t pte_mkread(pte_t pte) { + pte_val(pte) |= _PAGE_USER; return pte; } +static inline pte_t pte_mkexec(pte_t pte) { + pte_val(pte) |= _PAGE_USER | _PAGE_EXEC; return pte; } +static inline pte_t pte_mkwrite(pte_t pte) { + pte_val(pte) |= _PAGE_RW; return pte; } +static inline pte_t pte_mkdirty(pte_t pte) { + pte_val(pte) |= _PAGE_DIRTY; return pte; } +static inline pte_t pte_mkyoung(pte_t pte) { + pte_val(pte) |= _PAGE_ACCESSED; return pte; } +static inline pte_t pte_mkhuge(pte_t pte) { + return pte; } + +/* Atomic PTE updates */ +static inline unsigned long pte_update(struct mm_struct *mm, + unsigned long addr, + pte_t *ptep, unsigned long clr, + int huge) +{ + unsigned long old, tmp; + + __asm__ __volatile__( + "1: ldarx %0,0,%3 # pte_update\n\ + andi. %1,%0,%6\n\ + bne- 1b \n\ + andc %1,%0,%4 \n\ + stdcx. %1,0,%3 \n\ + bne- 1b" + : "=&r" (old), "=&r" (tmp), "=m" (*ptep) + : "r" (ptep), "r" (clr), "m" (*ptep), "i" (_PAGE_BUSY) + : "cc" ); + + if (old & _PAGE_HASHPTE) + hpte_need_flush(mm, addr, ptep, old, huge); + return old; +} + +static inline int __ptep_test_and_clear_young(struct mm_struct *mm, + unsigned long addr, pte_t *ptep) +{ + unsigned long old; + + if ((pte_val(*ptep) & (_PAGE_ACCESSED | _PAGE_HASHPTE)) == 0) + return 0; + old = pte_update(mm, addr, ptep, _PAGE_ACCESSED, 0); + return (old & _PAGE_ACCESSED) != 0; +} +#define __HAVE_ARCH_PTEP_TEST_AND_CLEAR_YOUNG +#define ptep_test_and_clear_young(__vma, __addr, __ptep) \ +({ \ + int __r; \ + __r = __ptep_test_and_clear_young((__vma)->vm_mm, __addr, __ptep); \ + __r; \ +}) + +/* + * On RW/DIRTY bit transitions we can avoid flushing the hpte. For the + * moment we always flush but we need to fix hpte_update and test if the + * optimisation is worth it. + */ +static inline int __ptep_test_and_clear_dirty(struct mm_struct *mm, + unsigned long addr, pte_t *ptep) +{ + unsigned long old; + + if ((pte_val(*ptep) & _PAGE_DIRTY) == 0) + return 0; + old = pte_update(mm, addr, ptep, _PAGE_DIRTY, 0); + return (old & _PAGE_DIRTY) != 0; +} +#define __HAVE_ARCH_PTEP_TEST_AND_CLEAR_DIRTY +#define ptep_test_and_clear_dirty(__vma, __addr, __ptep) \ +({ \ + int __r; \ + __r = __ptep_test_and_clear_dirty((__vma)->vm_mm, __addr, __ptep); \ + __r; \ +}) + +#define __HAVE_ARCH_PTEP_SET_WRPROTECT +static inline void ptep_set_wrprotect(struct mm_struct *mm, unsigned long addr, + pte_t *ptep) +{ + unsigned long old; + + if ((pte_val(*ptep) & _PAGE_RW) == 0) + return; + old = pte_update(mm, addr, ptep, _PAGE_RW, 0); +} + +/* + * We currently remove entries from the hashtable regardless of whether + * the entry was young or dirty. The generic routines only flush if the + * entry was young or dirty which is not good enough. + * + * We should be more intelligent about this but for the moment we override + * these functions and force a tlb flush unconditionally + */ +#define __HAVE_ARCH_PTEP_CLEAR_YOUNG_FLUSH +#define ptep_clear_flush_young(__vma, __address, __ptep) \ +({ \ + int __young = __ptep_test_and_clear_young((__vma)->vm_mm, __address, \ + __ptep); \ + __young; \ +}) + +#define __HAVE_ARCH_PTEP_CLEAR_DIRTY_FLUSH +#define ptep_clear_flush_dirty(__vma, __address, __ptep) \ +({ \ + int __dirty = __ptep_test_and_clear_dirty((__vma)->vm_mm, __address, \ + __ptep); \ + __dirty; \ +}) + +#define __HAVE_ARCH_PTEP_GET_AND_CLEAR +static inline pte_t ptep_get_and_clear(struct mm_struct *mm, + unsigned long addr, pte_t *ptep) +{ + unsigned long old = pte_update(mm, addr, ptep, ~0UL, 0); + return __pte(old); +} + +static inline void pte_clear(struct mm_struct *mm, unsigned long addr, + pte_t * ptep) +{ + pte_update(mm, addr, ptep, ~0UL, 0); +} + +/* + * set_pte stores a linux PTE into the linux page table. + */ +static inline void set_pte_at(struct mm_struct *mm, unsigned long addr, + pte_t *ptep, pte_t pte) +{ + if (pte_present(*ptep)) + pte_clear(mm, addr, ptep); + pte = __pte(pte_val(pte) & ~_PAGE_HPTEFLAGS); + *ptep = pte; +} + +/* Set the dirty and/or accessed bits atomically in a linux PTE, this + * function doesn't need to flush the hash entry + */ +#define __HAVE_ARCH_PTEP_SET_ACCESS_FLAGS +static inline void __ptep_set_access_flags(pte_t *ptep, pte_t entry, int dirty) +{ + unsigned long bits = pte_val(entry) & + (_PAGE_DIRTY | _PAGE_ACCESSED | _PAGE_RW | _PAGE_EXEC); + unsigned long old, tmp; + + __asm__ __volatile__( + "1: ldarx %0,0,%4\n\ + andi. %1,%0,%6\n\ + bne- 1b \n\ + or %0,%3,%0\n\ + stdcx. %0,0,%4\n\ + bne- 1b" + :"=&r" (old), "=&r" (tmp), "=m" (*ptep) + :"r" (bits), "r" (ptep), "m" (*ptep), "i" (_PAGE_BUSY) + :"cc"); +} +#define ptep_set_access_flags(__vma, __address, __ptep, __entry, __dirty) \ + do { \ + __ptep_set_access_flags(__ptep, __entry, __dirty); \ + flush_tlb_page_nohash(__vma, __address); \ + } while(0) + +/* + * Macro to mark a page protection value as "uncacheable". + */ +#define pgprot_noncached(prot) (__pgprot(pgprot_val(prot) | _PAGE_NO_CACHE | _PAGE_GUARDED)) + +struct file; +extern pgprot_t phys_mem_access_prot(struct file *file, unsigned long pfn, + unsigned long size, pgprot_t vma_prot); +#define __HAVE_PHYS_MEM_ACCESS_PROT + +#define __HAVE_ARCH_PTE_SAME +#define pte_same(A,B) (((pte_val(A) ^ pte_val(B)) & ~_PAGE_HPTEFLAGS) == 0) + +#define pte_ERROR(e) \ + printk("%s:%d: bad pte %08lx.\n", __FILE__, __LINE__, pte_val(e)) +#define pmd_ERROR(e) \ + printk("%s:%d: bad pmd %08lx.\n", __FILE__, __LINE__, pmd_val(e)) +#define pgd_ERROR(e) \ + printk("%s:%d: bad pgd %08lx.\n", __FILE__, __LINE__, pgd_val(e)) + +extern pgd_t swapper_pg_dir[]; + +extern void paging_init(void); + +/* Encode and de-code a swap entry */ +#define __swp_type(entry) (((entry).val >> 1) & 0x3f) +#define __swp_offset(entry) ((entry).val >> 8) +#define __swp_entry(type, offset) ((swp_entry_t){((type)<< 1)|((offset)<<8)}) +#define __pte_to_swp_entry(pte) ((swp_entry_t){pte_val(pte) >> PTE_RPN_SHIFT}) +#define __swp_entry_to_pte(x) ((pte_t) { (x).val << PTE_RPN_SHIFT }) +#define pte_to_pgoff(pte) (pte_val(pte) >> PTE_RPN_SHIFT) +#define pgoff_to_pte(off) ((pte_t) {((off) << PTE_RPN_SHIFT)|_PAGE_FILE}) +#define PTE_FILE_MAX_BITS (BITS_PER_LONG - PTE_RPN_SHIFT) + +/* + * kern_addr_valid is intended to indicate whether an address is a valid + * kernel address. Most 32-bit archs define it as always true (like this) + * but most 64-bit archs actually perform a test. What should we do here? + * The only use is in fs/ncpfs/dir.c + */ +#define kern_addr_valid(addr) (1) + +#define io_remap_pfn_range(vma, vaddr, pfn, size, prot) \ + remap_pfn_range(vma, vaddr, pfn, size, prot) + +void pgtable_cache_init(void); + +/* + * find_linux_pte returns the address of a linux pte for a given + * effective address and directory. If not found, it returns zero. + */static inline pte_t *find_linux_pte(pgd_t *pgdir, unsigned long ea) +{ + pgd_t *pg; + pud_t *pu; + pmd_t *pm; + pte_t *pt = NULL; + + pg = pgdir + pgd_index(ea); + if (!pgd_none(*pg)) { + pu = pud_offset(pg, ea); + if (!pud_none(*pu)) { + pm = pmd_offset(pu, ea); + if (pmd_present(*pm)) + pt = pte_offset_kernel(pm, ea); + } + } + return pt; +} + +#endif /* __ASSEMBLY__ */ + +#endif /* _ASM_POWERPC_PGTABLE_PPC64_H_ */ diff --git a/include/asm-powerpc/pgtable.h b/include/asm-powerpc/pgtable.h index 19edb6982b8..78bf4ae712a 100644 --- a/include/asm-powerpc/pgtable.h +++ b/include/asm-powerpc/pgtable.h @@ -2,502 +2,15 @@ #define _ASM_POWERPC_PGTABLE_H #ifdef __KERNEL__ -#ifndef CONFIG_PPC64 -#include <asm-ppc/pgtable.h> +#if defined(CONFIG_PPC64) +# include <asm/pgtable-ppc64.h> #else - -/* - * This file contains the functions and defines necessary to modify and use - * the ppc64 hashed page table. - */ - -#ifndef __ASSEMBLY__ -#include <linux/stddef.h> -#include <asm/processor.h> /* For TASK_SIZE */ -#include <asm/mmu.h> -#include <asm/page.h> -#include <asm/tlbflush.h> -struct mm_struct; -#endif /* __ASSEMBLY__ */ - -#ifdef CONFIG_PPC_64K_PAGES -#include <asm/pgtable-64k.h> -#else -#include <asm/pgtable-4k.h> -#endif - -#define FIRST_USER_ADDRESS 0 - -/* - * Size of EA range mapped by our pagetables. - */ -#define PGTABLE_EADDR_SIZE (PTE_INDEX_SIZE + PMD_INDEX_SIZE + \ - PUD_INDEX_SIZE + PGD_INDEX_SIZE + PAGE_SHIFT) -#define PGTABLE_RANGE (1UL << PGTABLE_EADDR_SIZE) - -#if TASK_SIZE_USER64 > PGTABLE_RANGE -#error TASK_SIZE_USER64 exceeds pagetable range -#endif - -#if TASK_SIZE_USER64 > (1UL << (USER_ESID_BITS + SID_SHIFT)) -#error TASK_SIZE_USER64 exceeds user VSID range +# include <asm/pgtable-ppc32.h> #endif -/* - * Define the address range of the vmalloc VM area. - */ -#define VMALLOC_START ASM_CONST(0xD000000000000000) -#define VMALLOC_SIZE ASM_CONST(0x80000000000) -#define VMALLOC_END (VMALLOC_START + VMALLOC_SIZE) - -/* - * Define the address range of the imalloc VM area. - */ -#define PHBS_IO_BASE VMALLOC_END -#define IMALLOC_BASE (PHBS_IO_BASE + 0x80000000ul) /* Reserve 2 gigs for PHBs */ -#define IMALLOC_END (VMALLOC_START + PGTABLE_RANGE) - -/* - * Region IDs - */ -#define REGION_SHIFT 60UL -#define REGION_MASK (0xfUL << REGION_SHIFT) -#define REGION_ID(ea) (((unsigned long)(ea)) >> REGION_SHIFT) - -#define VMALLOC_REGION_ID (REGION_ID(VMALLOC_START)) -#define KERNEL_REGION_ID (REGION_ID(PAGE_OFFSET)) -#define USER_REGION_ID (0UL) - -/* - * Common bits in a linux-style PTE. These match the bits in the - * (hardware-defined) PowerPC PTE as closely as possible. Additional - * bits may be defined in pgtable-*.h - */ -#define _PAGE_PRESENT 0x0001 /* software: pte contains a translation */ -#define _PAGE_USER 0x0002 /* matches one of the PP bits */ -#define _PAGE_FILE 0x0002 /* (!present only) software: pte holds file offset */ -#define _PAGE_EXEC 0x0004 /* No execute on POWER4 and newer (we invert) */ -#define _PAGE_GUARDED 0x0008 -#define _PAGE_COHERENT 0x0010 /* M: enforce memory coherence (SMP systems) */ -#define _PAGE_NO_CACHE 0x0020 /* I: cache inhibit */ -#define _PAGE_WRITETHRU 0x0040 /* W: cache write-through */ -#define _PAGE_DIRTY 0x0080 /* C: page changed */ -#define _PAGE_ACCESSED 0x0100 /* R: page referenced */ -#define _PAGE_RW 0x0200 /* software: user write access allowed */ -#define _PAGE_HASHPTE 0x0400 /* software: pte has an associated HPTE */ -#define _PAGE_BUSY 0x0800 /* software: PTE & hash are busy */ - -#define _PAGE_BASE (_PAGE_PRESENT | _PAGE_ACCESSED | _PAGE_COHERENT) - -#define _PAGE_WRENABLE (_PAGE_RW | _PAGE_DIRTY) - -/* __pgprot defined in asm-powerpc/page.h */ -#define PAGE_NONE __pgprot(_PAGE_PRESENT | _PAGE_ACCESSED) - -#define PAGE_SHARED __pgprot(_PAGE_BASE | _PAGE_RW | _PAGE_USER) -#define PAGE_SHARED_X __pgprot(_PAGE_BASE | _PAGE_RW | _PAGE_USER | _PAGE_EXEC) -#define PAGE_COPY __pgprot(_PAGE_BASE | _PAGE_USER) -#define PAGE_COPY_X __pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_EXEC) -#define PAGE_READONLY __pgprot(_PAGE_BASE | _PAGE_USER) -#define PAGE_READONLY_X __pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_EXEC) -#define PAGE_KERNEL __pgprot(_PAGE_BASE | _PAGE_WRENABLE) -#define PAGE_KERNEL_CI __pgprot(_PAGE_PRESENT | _PAGE_ACCESSED | \ - _PAGE_WRENABLE | _PAGE_NO_CACHE | _PAGE_GUARDED) -#define PAGE_KERNEL_EXEC __pgprot(_PAGE_BASE | _PAGE_WRENABLE | _PAGE_EXEC) - -#define PAGE_AGP __pgprot(_PAGE_BASE | _PAGE_WRENABLE | _PAGE_NO_CACHE) -#define HAVE_PAGE_AGP - -/* PTEIDX nibble */ -#define _PTEIDX_SECONDARY 0x8 -#define _PTEIDX_GROUP_IX 0x7 - - -/* - * POWER4 and newer have per page execute protection, older chips can only - * do this on a segment (256MB) basis. - * - * Also, write permissions imply read permissions. - * This is the closest we can get.. - * - * Note due to the way vm flags are laid out, the bits are XWR - */ -#define __P000 PAGE_NONE -#define __P001 PAGE_READONLY -#define __P010 PAGE_COPY -#define __P011 PAGE_COPY -#define __P100 PAGE_READONLY_X -#define __P101 PAGE_READONLY_X -#define __P110 PAGE_COPY_X -#define __P111 PAGE_COPY_X - -#define __S000 PAGE_NONE -#define __S001 PAGE_READONLY -#define __S010 PAGE_SHARED -#define __S011 PAGE_SHARED -#define __S100 PAGE_READONLY_X -#define __S101 PAGE_READONLY_X -#define __S110 PAGE_SHARED_X -#define __S111 PAGE_SHARED_X - #ifndef __ASSEMBLY__ - -/* - * ZERO_PAGE is a global shared page that is always zero: used - * for zero-mapped memory areas etc.. - */ -extern unsigned long empty_zero_page[PAGE_SIZE/sizeof(unsigned long)]; -#define ZERO_PAGE(vaddr) (virt_to_page(empty_zero_page)) -#endif /* __ASSEMBLY__ */ - -#ifdef CONFIG_HUGETLB_PAGE - -#define HAVE_ARCH_UNMAPPED_AREA -#define HAVE_ARCH_UNMAPPED_AREA_TOPDOWN - -#endif - -#ifndef __ASSEMBLY__ - -/* - * Conversion functions: convert a page and protection to a page entry, - * and a page entry and page directory to the page they refer to. - * - * mk_pte takes a (struct page *) as input - */ -#define mk_pte(page, pgprot) pfn_pte(page_to_pfn(page), (pgprot)) - -static inline pte_t pfn_pte(unsigned long pfn, pgprot_t pgprot) -{ - pte_t pte; - - - pte_val(pte) = (pfn << PTE_RPN_SHIFT) | pgprot_val(pgprot); - return pte; -} - -#define pte_modify(_pte, newprot) \ - (__pte((pte_val(_pte) & _PAGE_CHG_MASK) | pgprot_val(newprot))) - -#define pte_none(pte) ((pte_val(pte) & ~_PAGE_HPTEFLAGS) == 0) -#define pte_present(pte) (pte_val(pte) & _PAGE_PRESENT) - -/* pte_clear moved to later in this file */ - -#define pte_pfn(x) ((unsigned long)((pte_val(x)>>PTE_RPN_SHIFT))) -#define pte_page(x) pfn_to_page(pte_pfn(x)) - -#define PMD_BAD_BITS (PTE_TABLE_SIZE-1) -#define PUD_BAD_BITS (PMD_TABLE_SIZE-1) - -#define pmd_set(pmdp, pmdval) (pmd_val(*(pmdp)) = (pmdval)) -#define pmd_none(pmd) (!pmd_val(pmd)) -#define pmd_bad(pmd) (!is_kernel_addr(pmd_val(pmd)) \ - || (pmd_val(pmd) & PMD_BAD_BITS)) -#define pmd_present(pmd) (pmd_val(pmd) != 0) -#define pmd_clear(pmdp) (pmd_val(*(pmdp)) = 0) -#define pmd_page_vaddr(pmd) (pmd_val(pmd) & ~PMD_MASKED_BITS) -#define pmd_page(pmd) virt_to_page(pmd_page_vaddr(pmd)) - -#define pud_set(pudp, pudval) (pud_val(*(pudp)) = (pudval)) -#define pud_none(pud) (!pud_val(pud)) -#define pud_bad(pud) (!is_kernel_addr(pud_val(pud)) \ - || (pud_val(pud) & PUD_BAD_BITS)) -#define pud_present(pud) (pud_val(pud) != 0) -#define pud_clear(pudp) (pud_val(*(pudp)) = 0) -#define pud_page_vaddr(pud) (pud_val(pud) & ~PUD_MASKED_BITS) -#define pud_page(pud) virt_to_page(pud_page_vaddr(pud)) - -#define pgd_set(pgdp, pudp) ({pgd_val(*(pgdp)) = (unsigned long)(pudp);}) - -/* - * Find an entry in a page-table-directory. We combine the address region - * (the high order N bits) and the pgd portion of the address. - */ -/* to avoid overflow in free_pgtables we don't use PTRS_PER_PGD here */ -#define pgd_index(address) (((address) >> (PGDIR_SHIFT)) & 0x1ff) - -#define pgd_offset(mm, address) ((mm)->pgd + pgd_index(address)) - -#define pmd_offset(pudp,addr) \ - (((pmd_t *) pud_page_vaddr(*(pudp))) + (((addr) >> PMD_SHIFT) & (PTRS_PER_PMD - 1))) - -#define pte_offset_kernel(dir,addr) \ - (((pte_t *) pmd_page_vaddr(*(dir))) + (((addr) >> PAGE_SHIFT) & (PTRS_PER_PTE - 1))) - -#define pte_offset_map(dir,addr) pte_offset_kernel((dir), (addr)) -#define pte_offset_map_nested(dir,addr) pte_offset_kernel((dir), (addr)) -#define pte_unmap(pte) do { } while(0) -#define pte_unmap_nested(pte) do { } while(0) - -/* to find an entry in a kernel page-table-directory */ -/* This now only contains the vmalloc pages */ -#define pgd_offset_k(address) pgd_offset(&init_mm, address) - -/* - * The following only work if pte_present() is true. - * Undefined behaviour if not.. - */ -static inline int pte_read(pte_t pte) { return pte_val(pte) & _PAGE_USER;} -static inline int pte_write(pte_t pte) { return pte_val(pte) & _PAGE_RW;} -static inline int pte_exec(pte_t pte) { return pte_val(pte) & _PAGE_EXEC;} -static inline int pte_dirty(pte_t pte) { return pte_val(pte) & _PAGE_DIRTY;} -static inline int pte_young(pte_t pte) { return pte_val(pte) & _PAGE_ACCESSED;} -static inline int pte_file(pte_t pte) { return pte_val(pte) & _PAGE_FILE;} - -static inline void pte_uncache(pte_t pte) { pte_val(pte) |= _PAGE_NO_CACHE; } -static inline void pte_cache(pte_t pte) { pte_val(pte) &= ~_PAGE_NO_CACHE; } - -static inline pte_t pte_rdprotect(pte_t pte) { - pte_val(pte) &= ~_PAGE_USER; return pte; } -static inline pte_t pte_exprotect(pte_t pte) { - pte_val(pte) &= ~_PAGE_EXEC; return pte; } -static inline pte_t pte_wrprotect(pte_t pte) { - pte_val(pte) &= ~(_PAGE_RW); return pte; } -static inline pte_t pte_mkclean(pte_t pte) { - pte_val(pte) &= ~(_PAGE_DIRTY); return pte; } -static inline pte_t pte_mkold(pte_t pte) { - pte_val(pte) &= ~_PAGE_ACCESSED; return pte; } -static inline pte_t pte_mkread(pte_t pte) { - pte_val(pte) |= _PAGE_USER; return pte; } -static inline pte_t pte_mkexec(pte_t pte) { - pte_val(pte) |= _PAGE_USER | _PAGE_EXEC; return pte; } -static inline pte_t pte_mkwrite(pte_t pte) { - pte_val(pte) |= _PAGE_RW; return pte; } -static inline pte_t pte_mkdirty(pte_t pte) { - pte_val(pte) |= _PAGE_DIRTY; return pte; } -static inline pte_t pte_mkyoung(pte_t pte) { - pte_val(pte) |= _PAGE_ACCESSED; return pte; } -static inline pte_t pte_mkhuge(pte_t pte) { - return pte; } - -/* Atomic PTE updates */ -static inline unsigned long pte_update(struct mm_struct *mm, - unsigned long addr, - pte_t *ptep, unsigned long clr, - int huge) -{ - unsigned long old, tmp; - - __asm__ __volatile__( - "1: ldarx %0,0,%3 # pte_update\n\ - andi. %1,%0,%6\n\ - bne- 1b \n\ - andc %1,%0,%4 \n\ - stdcx. %1,0,%3 \n\ - bne- 1b" - : "=&r" (old), "=&r" (tmp), "=m" (*ptep) - : "r" (ptep), "r" (clr), "m" (*ptep), "i" (_PAGE_BUSY) - : "cc" ); - - if (old & _PAGE_HASHPTE) - hpte_need_flush(mm, addr, ptep, old, huge); - return old; -} - -static inline int __ptep_test_and_clear_young(struct mm_struct *mm, - unsigned long addr, pte_t *ptep) -{ - unsigned long old; - - if ((pte_val(*ptep) & (_PAGE_ACCESSED | _PAGE_HASHPTE)) == 0) - return 0; - old = pte_update(mm, addr, ptep, _PAGE_ACCESSED, 0); - return (old & _PAGE_ACCESSED) != 0; -} -#define __HAVE_ARCH_PTEP_TEST_AND_CLEAR_YOUNG -#define ptep_test_and_clear_young(__vma, __addr, __ptep) \ -({ \ - int __r; \ - __r = __ptep_test_and_clear_young((__vma)->vm_mm, __addr, __ptep); \ - __r; \ -}) - -/* - * On RW/DIRTY bit transitions we can avoid flushing the hpte. For the - * moment we always flush but we need to fix hpte_update and test if the - * optimisation is worth it. - */ -static inline int __ptep_test_and_clear_dirty(struct mm_struct *mm, - unsigned long addr, pte_t *ptep) -{ - unsigned long old; - - if ((pte_val(*ptep) & _PAGE_DIRTY) == 0) - return 0; - old = pte_update(mm, addr, ptep, _PAGE_DIRTY, 0); - return (old & _PAGE_DIRTY) != 0; -} -#define __HAVE_ARCH_PTEP_TEST_AND_CLEAR_DIRTY -#define ptep_test_and_clear_dirty(__vma, __addr, __ptep) \ -({ \ - int __r; \ - __r = __ptep_test_and_clear_dirty((__vma)->vm_mm, __addr, __ptep); \ - __r; \ -}) - -#define __HAVE_ARCH_PTEP_SET_WRPROTECT -static inline void ptep_set_wrprotect(struct mm_struct *mm, unsigned long addr, - pte_t *ptep) -{ - unsigned long old; - - if ((pte_val(*ptep) & _PAGE_RW) == 0) - return; - old = pte_update(mm, addr, ptep, _PAGE_RW, 0); -} - -/* - * We currently remove entries from the hashtable regardless of whether - * the entry was young or dirty. The generic routines only flush if the - * entry was young or dirty which is not good enough. - * - * We should be more intelligent about this but for the moment we override - * these functions and force a tlb flush unconditionally - */ -#define __HAVE_ARCH_PTEP_CLEAR_YOUNG_FLUSH -#define ptep_clear_flush_young(__vma, __address, __ptep) \ -({ \ - int __young = __ptep_test_and_clear_young((__vma)->vm_mm, __address, \ - __ptep); \ - __young; \ -}) - -#define __HAVE_ARCH_PTEP_CLEAR_DIRTY_FLUSH -#define ptep_clear_flush_dirty(__vma, __address, __ptep) \ -({ \ - int __dirty = __ptep_test_and_clear_dirty((__vma)->vm_mm, __address, \ - __ptep); \ - __dirty; \ -}) - -#define __HAVE_ARCH_PTEP_GET_AND_CLEAR -static inline pte_t ptep_get_and_clear(struct mm_struct *mm, - unsigned long addr, pte_t *ptep) -{ - unsigned long old = pte_update(mm, addr, ptep, ~0UL, 0); - return __pte(old); -} - -static inline void pte_clear(struct mm_struct *mm, unsigned long addr, - pte_t * ptep) -{ - pte_update(mm, addr, ptep, ~0UL, 0); -} - -/* - * set_pte stores a linux PTE into the linux page table. - */ -static inline void set_pte_at(struct mm_struct *mm, unsigned long addr, - pte_t *ptep, pte_t pte) -{ - if (pte_present(*ptep)) - pte_clear(mm, addr, ptep); - pte = __pte(pte_val(pte) & ~_PAGE_HPTEFLAGS); - *ptep = pte; -} - -/* Set the dirty and/or accessed bits atomically in a linux PTE, this - * function doesn't need to flush the hash entry - */ -#define __HAVE_ARCH_PTEP_SET_ACCESS_FLAGS -static inline void __ptep_set_access_flags(pte_t *ptep, pte_t entry, int dirty) -{ - unsigned long bits = pte_val(entry) & - (_PAGE_DIRTY | _PAGE_ACCESSED | _PAGE_RW | _PAGE_EXEC); - unsigned long old, tmp; - - __asm__ __volatile__( - "1: ldarx %0,0,%4\n\ - andi. %1,%0,%6\n\ - bne- 1b \n\ - or %0,%3,%0\n\ - stdcx. %0,0,%4\n\ - bne- 1b" - :"=&r" (old), "=&r" (tmp), "=m" (*ptep) - :"r" (bits), "r" (ptep), "m" (*ptep), "i" (_PAGE_BUSY) - :"cc"); -} -#define ptep_set_access_flags(__vma, __address, __ptep, __entry, __dirty) \ - do { \ - __ptep_set_access_flags(__ptep, __entry, __dirty); \ - flush_tlb_page_nohash(__vma, __address); \ - } while(0) - -/* - * Macro to mark a page protection value as "uncacheable". - */ -#define pgprot_noncached(prot) (__pgprot(pgprot_val(prot) | _PAGE_NO_CACHE | _PAGE_GUARDED)) - -struct file; -extern pgprot_t phys_mem_access_prot(struct file *file, unsigned long pfn, - unsigned long size, pgprot_t vma_prot); -#define __HAVE_PHYS_MEM_ACCESS_PROT - -#define __HAVE_ARCH_PTE_SAME -#define pte_same(A,B) (((pte_val(A) ^ pte_val(B)) & ~_PAGE_HPTEFLAGS) == 0) - -#define pte_ERROR(e) \ - printk("%s:%d: bad pte %08lx.\n", __FILE__, __LINE__, pte_val(e)) -#define pmd_ERROR(e) \ - printk("%s:%d: bad pmd %08lx.\n", __FILE__, __LINE__, pmd_val(e)) -#define pgd_ERROR(e) \ - printk("%s:%d: bad pgd %08lx.\n", __FILE__, __LINE__, pgd_val(e)) - -extern pgd_t swapper_pg_dir[]; - -extern void paging_init(void); - -/* Encode and de-code a swap entry */ -#define __swp_type(entry) (((entry).val >> 1) & 0x3f) -#define __swp_offset(entry) ((entry).val >> 8) -#define __swp_entry(type, offset) ((swp_entry_t){((type)<< 1)|((offset)<<8)}) -#define __pte_to_swp_entry(pte) ((swp_entry_t){pte_val(pte) >> PTE_RPN_SHIFT}) -#define __swp_entry_to_pte(x) ((pte_t) { (x).val << PTE_RPN_SHIFT }) -#define pte_to_pgoff(pte) (pte_val(pte) >> PTE_RPN_SHIFT) -#define pgoff_to_pte(off) ((pte_t) {((off) << PTE_RPN_SHIFT)|_PAGE_FILE}) -#define PTE_FILE_MAX_BITS (BITS_PER_LONG - PTE_RPN_SHIFT) - -/* - * kern_addr_valid is intended to indicate whether an address is a valid - * kernel address. Most 32-bit archs define it as always true (like this) - * but most 64-bit archs actually perform a test. What should we do here? - * The only use is in fs/ncpfs/dir.c - */ -#define kern_addr_valid(addr) (1) - -#define io_remap_pfn_range(vma, vaddr, pfn, size, prot) \ - remap_pfn_range(vma, vaddr, pfn, size, prot) - -void pgtable_cache_init(void); - -/* - * find_linux_pte returns the address of a linux pte for a given - * effective address and directory. If not found, it returns zero. - */static inline pte_t *find_linux_pte(pgd_t *pgdir, unsigned long ea) -{ - pgd_t *pg; - pud_t *pu; - pmd_t *pm; - pte_t *pt = NULL; - - pg = pgdir + pgd_index(ea); - if (!pgd_none(*pg)) { - pu = pud_offset(pg, ea); - if (!pud_none(*pu)) { - pm = pmd_offset(pu, ea); - if (pmd_present(*pm)) - pt = pte_offset_kernel(pm, ea); - } - } - return pt; -} - - #include <asm-generic/pgtable.h> - #endif /* __ASSEMBLY__ */ -#endif /* CONFIG_PPC64 */ #endif /* __KERNEL__ */ #endif /* _ASM_POWERPC_PGTABLE_H */ diff --git a/include/asm-powerpc/pmac_feature.h b/include/asm-powerpc/pmac_feature.h index d3599cc9aa7..d43d91beba9 100644 --- a/include/asm-powerpc/pmac_feature.h +++ b/include/asm-powerpc/pmac_feature.h @@ -146,7 +146,7 @@ struct device_node; static inline long pmac_call_feature(int selector, struct device_node* node, long param, long value) { - if (!ppc_md.feature_call) + if (!ppc_md.feature_call || !machine_is(powermac)) return -ENODEV; return ppc_md.feature_call(selector, node, param, value); } diff --git a/include/asm-powerpc/prom.h b/include/asm-powerpc/prom.h index ec400f608e1..6845af93ba9 100644 --- a/include/asm-powerpc/prom.h +++ b/include/asm-powerpc/prom.h @@ -20,7 +20,6 @@ #include <linux/platform_device.h> #include <asm/irq.h> #include <asm/atomic.h> -#include <asm/io.h> /* Definitions used by the flattened device tree */ #define OF_DT_HEADER 0xd00dfeed /* marker */ @@ -334,30 +333,17 @@ extern int of_irq_map_one(struct device_node *device, int index, struct pci_dev; extern int of_irq_map_pci(struct pci_dev *pdev, struct of_irq *out_irq); -static inline int of_irq_to_resource(struct device_node *dev, int index, struct resource *r) -{ - int irq = irq_of_parse_and_map(dev, index); - - /* Only dereference the resource if both the - * resource and the irq are valid. */ - if (r && irq != NO_IRQ) { - r->start = r->end = irq; - r->flags = IORESOURCE_IRQ; - } - - return irq; -} - -static inline void __iomem *of_iomap(struct device_node *np, int index) -{ - struct resource res; - - if (of_address_to_resource(np, index, &res)) - return NULL; - - return ioremap(res.start, 1 + res.end - res.start); -} +extern int of_irq_to_resource(struct device_node *dev, int index, + struct resource *r); +/** + * of_iomap - Maps the memory mapped IO for a given device_node + * @device: the device whose io range will be mapped + * @index: index of the io range + * + * Returns a pointer to the mapped memory + */ +extern void __iomem *of_iomap(struct device_node *device, int index); #endif /* __KERNEL__ */ #endif /* _POWERPC_PROM_H */ diff --git a/include/asm-powerpc/ps3.h b/include/asm-powerpc/ps3.h index 821581a8b64..13c372df99e 100644 --- a/include/asm-powerpc/ps3.h +++ b/include/asm-powerpc/ps3.h @@ -167,26 +167,31 @@ enum ps3_cpu_binding { PS3_BINDING_CPU_1 = 1, }; -int ps3_alloc_io_irq(enum ps3_cpu_binding cpu, unsigned int interrupt_id, +int ps3_virq_setup(enum ps3_cpu_binding cpu, unsigned long outlet, unsigned int *virq); -int ps3_free_io_irq(unsigned int virq); -int ps3_alloc_event_irq(enum ps3_cpu_binding cpu, unsigned int *virq); -int ps3_free_event_irq(unsigned int virq); +int ps3_virq_destroy(unsigned int virq); +int ps3_irq_plug_setup(enum ps3_cpu_binding cpu, unsigned long outlet, + unsigned int *virq); +int ps3_irq_plug_destroy(unsigned int virq); +int ps3_event_receive_port_setup(enum ps3_cpu_binding cpu, unsigned int *virq); +int ps3_event_receive_port_destroy(unsigned int virq); int ps3_send_event_locally(unsigned int virq); -int ps3_connect_event_irq(enum ps3_cpu_binding cpu, - const struct ps3_device_id *did, unsigned int interrupt_id, + +int ps3_io_irq_setup(enum ps3_cpu_binding cpu, unsigned int interrupt_id, unsigned int *virq); -int ps3_disconnect_event_irq(const struct ps3_device_id *did, - unsigned int interrupt_id, unsigned int virq); -int ps3_alloc_vuart_irq(enum ps3_cpu_binding cpu, void* virt_addr_bmp, +int ps3_io_irq_destroy(unsigned int virq); +int ps3_vuart_irq_setup(enum ps3_cpu_binding cpu, void* virt_addr_bmp, unsigned int *virq); -int ps3_free_vuart_irq(unsigned int virq); -int ps3_alloc_spe_irq(enum ps3_cpu_binding cpu, unsigned long spe_id, +int ps3_vuart_irq_destroy(unsigned int virq); +int ps3_spe_irq_setup(enum ps3_cpu_binding cpu, unsigned long spe_id, unsigned int class, unsigned int *virq); -int ps3_free_spe_irq(unsigned int virq); -int ps3_alloc_irq(enum ps3_cpu_binding cpu, unsigned long outlet, +int ps3_spe_irq_destroy(unsigned int virq); + +int ps3_sb_event_receive_port_setup(enum ps3_cpu_binding cpu, + const struct ps3_device_id *did, unsigned int interrupt_id, unsigned int *virq); -int ps3_free_irq(unsigned int virq); +int ps3_sb_event_receive_port_destroy(const struct ps3_device_id *did, + unsigned int interrupt_id, unsigned int virq); /* lv1 result codes */ diff --git a/include/asm-powerpc/suspend.h b/include/asm-powerpc/suspend.h new file mode 100644 index 00000000000..cbf2c9404c3 --- /dev/null +++ b/include/asm-powerpc/suspend.h @@ -0,0 +1,9 @@ +#ifndef __ASM_POWERPC_SUSPEND_H +#define __ASM_POWERPC_SUSPEND_H + +static inline int arch_prepare_suspend(void) { return 0; } + +void save_processor_state(void); +void restore_processor_state(void); + +#endif /* __ASM_POWERPC_SUSPEND_H */ diff --git a/include/asm-powerpc/tsi108.h b/include/asm-powerpc/tsi108.h index 4e95d153be8..f8b60793b7a 100644 --- a/include/asm-powerpc/tsi108.h +++ b/include/asm-powerpc/tsi108.h @@ -68,8 +68,17 @@ #define TSI108_PB_ERRCS_ES (1 << 1) #define TSI108_PB_ISR_PBS_RD_ERR (1 << 8) -#define TSI108_PCI_CFG_BASE_PHYS (0xfb000000) #define TSI108_PCI_CFG_SIZE (0x01000000) + +/* + * PHY Configuration Options + * + * Specify "bcm54xx" in the compatible property of your device tree phy + * nodes if your board uses the Broadcom PHYs + */ +#define TSI108_PHY_MV88E 0 /* Marvel 88Exxxx PHY */ +#define TSI108_PHY_BCM54XX 1 /* Broardcom BCM54xx PHY */ + /* Global variables */ extern u32 tsi108_pci_cfg_base; @@ -93,6 +102,7 @@ typedef struct { u16 phy; /* phy address */ u16 irq_num; /* irq number */ u8 mac_addr[6]; /* phy mac address */ + u16 phy_type; /* type of phy on board */ } hw_info; extern u32 get_vir_csrbase(void); diff --git a/include/asm-powerpc/tsi108_pci.h b/include/asm-powerpc/tsi108_pci.h new file mode 100644 index 00000000000..a9f92f73232 --- /dev/null +++ b/include/asm-powerpc/tsi108_pci.h @@ -0,0 +1,45 @@ +/* + * Copyright 2007 IBM Corp + * + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _ASM_PPC_TSI108_PCI_H +#define _ASM_PPC_TSI108_PCI_H + +#include <asm/tsi108.h> + +/* Register definitions */ +#define TSI108_PCI_P2O_BAR0 (TSI108_PCI_OFFSET + 0x10) +#define TSI108_PCI_P2O_BAR0_UPPER (TSI108_PCI_OFFSET + 0x14) +#define TSI108_PCI_P2O_BAR2 (TSI108_PCI_OFFSET + 0x18) +#define TSI108_PCI_P2O_BAR2_UPPER (TSI108_PCI_OFFSET + 0x1c) +#define TSI108_PCI_P2O_PAGE_SIZES (TSI108_PCI_OFFSET + 0x4c) +#define TSI108_PCI_PFAB_BAR0 (TSI108_PCI_OFFSET + 0x204) +#define TSI108_PCI_PFAB_BAR0_UPPER (TSI108_PCI_OFFSET + 0x208) +#define TSI108_PCI_PFAB_IO (TSI108_PCI_OFFSET + 0x20c) +#define TSI108_PCI_PFAB_IO_UPPER (TSI108_PCI_OFFSET + 0x210) +#define TSI108_PCI_PFAB_MEM32 (TSI108_PCI_OFFSET + 0x214) +#define TSI108_PCI_PFAB_PFM3 (TSI108_PCI_OFFSET + 0x220) +#define TSI108_PCI_PFAB_PFM4 (TSI108_PCI_OFFSET + 0x230) + +extern int tsi108_setup_pci(struct device_node *dev, u32 cfg_phys, int primary); +extern void tsi108_pci_int_init(struct device_node *node); +extern void tsi108_irq_cascade(unsigned int irq, struct irq_desc *desc); +extern void tsi108_clear_pci_cfg_error(void); + +#endif /* _ASM_PPC_TSI108_PCI_H */ diff --git a/include/linux/pmu.h b/include/linux/pmu.h index b0952e532ed..37ca57392ad 100644 --- a/include/linux/pmu.h +++ b/include/linux/pmu.h @@ -225,4 +225,12 @@ extern unsigned int pmu_power_flags; /* Backlight */ extern void pmu_backlight_init(void); +/* some code needs to know if the PMU was suspended for hibernation */ +#ifdef CONFIG_PM +extern int pmu_sys_suspended; +#else +/* if power management is not configured it can't be suspended */ +#define pmu_sys_suspended 0 +#endif + #endif /* __KERNEL__ */ diff --git a/include/linux/suspend.h b/include/linux/suspend.h index 96868be9c21..9d2aa1a12aa 100644 --- a/include/linux/suspend.h +++ b/include/linux/suspend.h @@ -1,7 +1,7 @@ #ifndef _LINUX_SWSUSP_H #define _LINUX_SWSUSP_H -#if defined(CONFIG_X86) || defined(CONFIG_FRV) || defined(CONFIG_PPC32) +#if defined(CONFIG_X86) || defined(CONFIG_FRV) || defined(CONFIG_PPC32) || defined(CONFIG_PPC64) #include <asm/suspend.h> #endif #include <linux/swap.h> diff --git a/kernel/power/Kconfig b/kernel/power/Kconfig index 877721708fa..495b7d4dd33 100644 --- a/kernel/power/Kconfig +++ b/kernel/power/Kconfig @@ -79,7 +79,7 @@ config PM_SYSFS_DEPRECATED config SOFTWARE_SUSPEND bool "Software Suspend (Hibernation)" - depends on PM && SWAP && ((X86 && (!SMP || SUSPEND_SMP)) || ((FRV || PPC32) && !SMP)) + depends on PM && SWAP && (((X86 || PPC64_SWSUSP) && (!SMP || SUSPEND_SMP)) || ((FRV || PPC32) && !SMP)) ---help--- Enable the suspend to disk (STD) functionality, which is usually called "hibernation" in user interfaces. STD checkpoints the @@ -139,7 +139,7 @@ config PM_STD_PARTITION config SUSPEND_SMP bool - depends on HOTPLUG_CPU && X86 && PM + depends on HOTPLUG_CPU && (X86 || PPC64) && PM default y config APM_EMULATION diff --git a/sound/aoa/codecs/snd-aoa-codec-onyx.c b/sound/aoa/codecs/snd-aoa-codec-onyx.c index 7f980be5d06..e91f9f66f39 100644 --- a/sound/aoa/codecs/snd-aoa-codec-onyx.c +++ b/sound/aoa/codecs/snd-aoa-codec-onyx.c @@ -1061,7 +1061,7 @@ static int onyx_i2c_attach(struct i2c_adapter *adapter) busnode = pmac_i2c_get_bus_node(bus); while ((dev = of_get_next_child(busnode, dev)) != NULL) { - if (device_is_compatible(dev, "pcm3052")) { + if (of_device_is_compatible(dev, "pcm3052")) { const u32 *addr; printk(KERN_DEBUG PFX "found pcm3052\n"); addr = of_get_property(dev, "reg", NULL); @@ -1074,7 +1074,7 @@ static int onyx_i2c_attach(struct i2c_adapter *adapter) /* if that didn't work, try desperate mode for older * machines that have stuff missing from the device tree */ - if (!device_is_compatible(busnode, "k2-i2c")) + if (!of_device_is_compatible(busnode, "k2-i2c")) return -ENODEV; printk(KERN_DEBUG PFX "found k2-i2c, checking if onyx chip is on it\n"); diff --git a/sound/aoa/codecs/snd-aoa-codec-tas.c b/sound/aoa/codecs/snd-aoa-codec-tas.c index ceca38486ea..041fe52cbf2 100644 --- a/sound/aoa/codecs/snd-aoa-codec-tas.c +++ b/sound/aoa/codecs/snd-aoa-codec-tas.c @@ -938,7 +938,7 @@ static int tas_i2c_attach(struct i2c_adapter *adapter) busnode = pmac_i2c_get_bus_node(bus); while ((dev = of_get_next_child(busnode, dev)) != NULL) { - if (device_is_compatible(dev, "tas3004")) { + if (of_device_is_compatible(dev, "tas3004")) { const u32 *addr; printk(KERN_DEBUG PFX "found tas3004\n"); addr = of_get_property(dev, "reg", NULL); diff --git a/sound/aoa/soundbus/i2sbus/i2sbus-core.c b/sound/aoa/soundbus/i2sbus/i2sbus-core.c index 79fc4bc09e5..0fccdbf5166 100644 --- a/sound/aoa/soundbus/i2sbus/i2sbus-core.c +++ b/sound/aoa/soundbus/i2sbus/i2sbus-core.c @@ -336,8 +336,8 @@ static int i2sbus_probe(struct macio_dev* dev, const struct of_device_id *match) } while ((np = of_get_next_child(dev->ofdev.node, np))) { - if (device_is_compatible(np, "i2sbus") || - device_is_compatible(np, "i2s-modem")) { + if (of_device_is_compatible(np, "i2sbus") || + of_device_is_compatible(np, "i2s-modem")) { got += i2sbus_add_dev(dev, control, np); } } diff --git a/sound/oss/dmasound/dmasound_awacs.c b/sound/oss/dmasound/dmasound_awacs.c index 730fa1d001a..8f6388004f4 100644 --- a/sound/oss/dmasound/dmasound_awacs.c +++ b/sound/oss/dmasound/dmasound_awacs.c @@ -362,7 +362,7 @@ setup_audio_gpio(const char *name, const char* compatible, int *gpio_addr, int* of_get_property(np,"audio-gpio",NULL); if (property != 0 && strcmp(property,name) == 0) break; - } else if (compatible && device_is_compatible(np, compatible)) + } else if (compatible && of_device_is_compatible(np, compatible)) break; np = of_get_next_child(gpiop, np); } @@ -2620,17 +2620,17 @@ get_codec_type(struct device_node *info) if (info) { /* must do awacs first to allow screamer to overide it */ - if (device_is_compatible(info, "awacs")) + if (of_device_is_compatible(info, "awacs")) codec = AWACS_AWACS ; - if (device_is_compatible(info, "screamer")) + if (of_device_is_compatible(info, "screamer")) codec = AWACS_SCREAMER; - if (device_is_compatible(info, "burgundy")) + if (of_device_is_compatible(info, "burgundy")) codec = AWACS_BURGUNDY ; - if (device_is_compatible(info, "daca")) + if (of_device_is_compatible(info, "daca")) codec = AWACS_DACA; - if (device_is_compatible(info, "tumbler")) + if (of_device_is_compatible(info, "tumbler")) codec = AWACS_TUMBLER; - if (device_is_compatible(info, "snapper")) + if (of_device_is_compatible(info, "snapper")) codec = AWACS_SNAPPER; } return codec ; @@ -2772,7 +2772,7 @@ set_hw_byteswap(struct device_node *io) for (mio = io->parent; mio ; mio = mio->parent) { if (strcmp(mio->name, "mac-io") == 0) { - if (device_is_compatible(mio, "Keylargo")) + if (of_device_is_compatible(mio, "Keylargo")) kl = 1; break; } diff --git a/sound/ppc/pmac.c b/sound/ppc/pmac.c index 2bae9c1a2b5..5a2bef44a2f 100644 --- a/sound/ppc/pmac.c +++ b/sound/ppc/pmac.c @@ -843,7 +843,7 @@ static void __init detect_byte_swap(struct snd_pmac *chip) /* if seems that Keylargo can't byte-swap */ for (mio = chip->node->parent; mio; mio = mio->parent) { if (strcmp(mio->name, "mac-io") == 0) { - if (device_is_compatible(mio, "Keylargo")) + if (of_device_is_compatible(mio, "Keylargo")) chip->can_byte_swap = 0; break; } @@ -910,7 +910,7 @@ static int __init snd_pmac_detect(struct snd_pmac *chip) chip->node = of_find_node_by_name(NULL, "i2s-a"); if (chip->node && chip->node->parent && chip->node->parent->parent) { - if (device_is_compatible(chip->node->parent->parent, + if (of_device_is_compatible(chip->node->parent->parent, "K2-Keylargo")) chip->is_k2 = 1; } @@ -941,22 +941,22 @@ static int __init snd_pmac_detect(struct snd_pmac *chip) return -ENODEV; } /* This should be verified on older screamers */ - if (device_is_compatible(sound, "screamer")) { + if (of_device_is_compatible(sound, "screamer")) { chip->model = PMAC_SCREAMER; // chip->can_byte_swap = 0; /* FIXME: check this */ } - if (device_is_compatible(sound, "burgundy")) { + if (of_device_is_compatible(sound, "burgundy")) { chip->model = PMAC_BURGUNDY; chip->control_mask = MASK_IEPC | 0x11; /* disable IEE */ } - if (device_is_compatible(sound, "daca")) { + if (of_device_is_compatible(sound, "daca")) { chip->model = PMAC_DACA; chip->can_capture = 0; /* no capture */ chip->can_duplex = 0; // chip->can_byte_swap = 0; /* FIXME: check this */ chip->control_mask = MASK_IEPC | 0x11; /* disable IEE */ } - if (device_is_compatible(sound, "tumbler")) { + if (of_device_is_compatible(sound, "tumbler")) { chip->model = PMAC_TUMBLER; chip->can_capture = 0; /* no capture */ chip->can_duplex = 0; @@ -965,7 +965,7 @@ static int __init snd_pmac_detect(struct snd_pmac *chip) chip->freq_table = tumbler_freqs; chip->control_mask = MASK_IEPC | 0x11; /* disable IEE */ } - if (device_is_compatible(sound, "snapper")) { + if (of_device_is_compatible(sound, "snapper")) { chip->model = PMAC_SNAPPER; // chip->can_byte_swap = 0; /* FIXME: check this */ chip->num_freqs = ARRAY_SIZE(tumbler_freqs); diff --git a/sound/ppc/tumbler.c b/sound/ppc/tumbler.c index 54e333fbb1d..5821cdd0bec 100644 --- a/sound/ppc/tumbler.c +++ b/sound/ppc/tumbler.c @@ -1060,7 +1060,7 @@ static struct device_node *find_compatible_audio_device(const char *name) for (np = of_get_next_child(gpiop, NULL); np; np = of_get_next_child(gpiop, np)) { - if (device_is_compatible(np, name)) + if (of_device_is_compatible(np, name)) break; } of_node_put(gpiop); |