summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
Diffstat
-rw-r--r--arch/blackfin/Kconfig4
-rw-r--r--arch/blackfin/configs/BF527-AD7160-EVAL_defconfig105
-rw-r--r--arch/blackfin/mach-bf527/boards/Kconfig5
-rw-r--r--arch/blackfin/mach-bf527/boards/Makefile1
-rw-r--r--arch/blackfin/mach-bf527/boards/ad7160eval.c870
5 files changed, 984 insertions, 1 deletions
diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index 5a3152b75cd..d243e228512 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -356,7 +356,7 @@ config MEM_MT48LC8M32B2B5_7
config MEM_MT48LC32M16A2TG_75
bool
- depends on (BFIN527_EZKIT || BFIN527_EZKIT_V2 || BFIN532_IP0X || BLACKSTAMP)
+ depends on (BFIN527_EZKIT || BFIN527_EZKIT_V2 || BFIN532_IP0X || BLACKSTAMP || BFIN527_AD7160EVAL)
default y
config MEM_MT48H32M16LFCJ_75
@@ -426,6 +426,7 @@ config CLKIN_HZ
default "25000000" # most people use this
default "27000000" if BFIN533_EZKIT
default "30000000" if BFIN561_EZKIT
+ default "24000000" if BFIN527_AD7160EVAL
help
The frequency of CLKIN crystal oscillator on the board in Hz.
Warning: This value should match the crystal on the board. Otherwise,
@@ -463,6 +464,7 @@ config VCO_MULT
default "20" if (BFIN537_BLUETECHNIX_CM_E || BFIN537_BLUETECHNIX_CM_U || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
default "20" if BFIN561_EZKIT
default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN518F_EZBRD)
+ default "25" if BFIN527_AD7160EVAL
help
This controls the frequency of the on-chip PLL. This can be between 1 and 64.
PLL Frequency = (Crystal Frequency) * (this setting)
diff --git a/arch/blackfin/configs/BF527-AD7160-EVAL_defconfig b/arch/blackfin/configs/BF527-AD7160-EVAL_defconfig
new file mode 100644
index 00000000000..08c55f6b8b7
--- /dev/null
+++ b/arch/blackfin/configs/BF527-AD7160-EVAL_defconfig
@@ -0,0 +1,105 @@
+CONFIG_EXPERIMENTAL=y
+CONFIG_SYSVIPC=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_EMBEDDED=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_AIO is not set
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_PREEMPT=y
+CONFIG_BF527=y
+CONFIG_BF_REV_0_2=y
+CONFIG_IRQ_TWI=7
+CONFIG_IRQ_PORTH_INTA=7
+CONFIG_IRQ_PORTH_INTB=7
+CONFIG_BFIN527_AD7160EVAL=y
+CONFIG_BF527_SPORT0_PORTF=y
+CONFIG_BF527_UART1_PORTG=y
+CONFIG_IRQ_USB_INT0=11
+CONFIG_IRQ_USB_INT1=11
+CONFIG_IRQ_USB_INT2=11
+CONFIG_IRQ_USB_DMA=11
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="bootargs=root=/dev/mtdblock0 rw clkin_hz=24000000 earlyprintk=serial,uart0,57600 console=tty0 console=ttyBF0,57600"
+CONFIG_CLKIN_HZ=24000000
+CONFIG_HZ_300=y
+# CONFIG_CYCLES_CLOCKSOURCE is not set
+CONFIG_IP_CHECKSUM_L1=y
+CONFIG_SYSCALL_TAB_L1=y
+CONFIG_CPLB_SWITCH_TAB_L1=y
+CONFIG_BFIN_GPTIMERS=y
+CONFIG_C_CDPRIO=y
+CONFIG_BANK_1=0x5554
+CONFIG_BANK_3=0xFFC0
+CONFIG_BINFMT_FLAT=y
+CONFIG_BINFMT_ZFLAT=y
+CONFIG_NET=y
+CONFIG_UNIX=y
+# CONFIG_WIRELESS is not set
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_AD7160=y
+CONFIG_TOUCHSCREEN_AD7160_FW=y
+# CONFIG_SERIO is not set
+# CONFIG_BFIN_DMA_INTERFACE is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_BFIN=y
+CONFIG_SERIAL_BFIN_CONSOLE=y
+CONFIG_SERIAL_BFIN_UART0=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_BFIN_OTP is not set
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C=y
+# CONFIG_I2C_HELPER_AUTO is not set
+CONFIG_I2C_ALGOBIT=y
+CONFIG_I2C_BLACKFIN_TWI=y
+CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=400
+CONFIG_SPI=y
+CONFIG_SPI_BFIN=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+# CONFIG_LOGO_BLACKFIN_VGA16 is not set
+# CONFIG_HID_SUPPORT is not set
+CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_GADGET_MUSB_HDRC=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VBUS_DRAW=500
+CONFIG_USB_G_SERIAL=y
+CONFIG_MMC=y
+CONFIG_MMC_SPI=y
+CONFIG_EXT2_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set
+CONFIG_EARLY_PRINTK=y
+CONFIG_CPLB_INFO=y
+CONFIG_SECURITY=y
+CONFIG_CRC_CCITT=m
diff --git a/arch/blackfin/mach-bf527/boards/Kconfig b/arch/blackfin/mach-bf527/boards/Kconfig
index b14c28810a4..646bc66def6 100644
--- a/arch/blackfin/mach-bf527/boards/Kconfig
+++ b/arch/blackfin/mach-bf527/boards/Kconfig
@@ -24,4 +24,9 @@ config BFIN526_EZBRD
help
BF526-EZBRD/EZKIT Lite board support.
+config BFIN527_AD7160EVAL
+ bool "BF527-AD7160-EVAL"
+ help
+ BF527-AD7160-EVAL board support.
+
endchoice
diff --git a/arch/blackfin/mach-bf527/boards/Makefile b/arch/blackfin/mach-bf527/boards/Makefile
index 51a5817c4a9..751d45cdf72 100644
--- a/arch/blackfin/mach-bf527/boards/Makefile
+++ b/arch/blackfin/mach-bf527/boards/Makefile
@@ -6,3 +6,4 @@ obj-$(CONFIG_BFIN527_EZKIT) += ezkit.o
obj-$(CONFIG_BFIN527_EZKIT_V2) += ezkit.o
obj-$(CONFIG_BFIN527_BLUETECHNIX_CM) += cm_bf527.o
obj-$(CONFIG_BFIN526_EZBRD) += ezbrd.o
+obj-$(CONFIG_BFIN527_AD7160EVAL) += ad7160eval.o
diff --git a/arch/blackfin/mach-bf527/boards/ad7160eval.c b/arch/blackfin/mach-bf527/boards/ad7160eval.c
new file mode 100644
index 00000000000..fc767ac7638
--- /dev/null
+++ b/arch/blackfin/mach-bf527/boards/ad7160eval.c
@@ -0,0 +1,870 @@
+/*
+ * Copyright 2004-20010 Analog Devices Inc.
+ * 2005 National ICT Australia (NICTA)
+ * Aidan Williams <aidan@nicta.com.au>
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/i2c.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/usb/musb.h>
+#include <linux/leds.h>
+#include <linux/input.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/reboot.h>
+#include <asm/nand.h>
+#include <asm/portmux.h>
+#include <asm/dpmc.h>
+
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "ADI BF527-AD7160EVAL";
+
+/*
+ * Driver needs to know address, irq and flag pin.
+ */
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+static struct resource musb_resources[] = {
+ [0] = {
+ .start = 0xffc03800,
+ .end = 0xffc03cff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = { /* general IRQ */
+ .start = IRQ_USB_INT0,
+ .end = IRQ_USB_INT0,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+ [2] = { /* DMA IRQ */
+ .start = IRQ_USB_DMA,
+ .end = IRQ_USB_DMA,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct musb_hdrc_config musb_config = {
+ .multipoint = 0,
+ .dyn_fifo = 0,
+ .soft_con = 1,
+ .dma = 1,
+ .num_eps = 8,
+ .dma_channels = 8,
+ .gpio_vrsel = GPIO_PG13,
+ /* Some custom boards need to be active low, just set it to "0"
+ * if it is the case.
+ */
+ .gpio_vrsel_active = 1,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_USB_MUSB_OTG)
+ .mode = MUSB_OTG,
+#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
+ .mode = MUSB_HOST,
+#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
+ .mode = MUSB_PERIPHERAL,
+#endif
+ .config = &musb_config,
+};
+
+static u64 musb_dmamask = ~(u32)0;
+
+static struct platform_device musb_device = {
+ .name = "musb_hdrc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &musb_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ .platform_data = &musb_plat,
+ },
+ .num_resources = ARRAY_SIZE(musb_resources),
+ .resource = musb_resources,
+};
+#endif
+
+#if defined(CONFIG_FB_BFIN_RA158Z) || defined(CONFIG_FB_BFIN_RA158Z_MODULE)
+static struct resource bf52x_ra158z_resources[] = {
+ {
+ .start = IRQ_PPI_ERROR,
+ .end = IRQ_PPI_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bf52x_ra158z_device = {
+ .name = "bfin-ra158z",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bf52x_ra158z_resources),
+ .resource = bf52x_ra158z_resources,
+};
+#endif
+
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+static struct mtd_partition ad7160eval_partitions[] = {
+ {
+ .name = "bootloader(nor)",
+ .size = 0x40000,
+ .offset = 0,
+ }, {
+ .name = "linux kernel(nor)",
+ .size = 0x1C0000,
+ .offset = MTDPART_OFS_APPEND,
+ }, {
+ .name = "file system(nor)",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ }
+};
+
+static struct physmap_flash_data ad7160eval_flash_data = {
+ .width = 2,
+ .parts = ad7160eval_partitions,
+ .nr_parts = ARRAY_SIZE(ad7160eval_partitions),
+};
+
+static struct resource ad7160eval_flash_resource = {
+ .start = 0x20000000,
+ .end = 0x203fffff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device ad7160eval_flash_device = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &ad7160eval_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &ad7160eval_flash_resource,
+};
+#endif
+
+#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+static struct mtd_partition partition_info[] = {
+ {
+ .name = "linux kernel(nand)",
+ .offset = 0,
+ .size = 4 * 1024 * 1024,
+ },
+ {
+ .name = "file system(nand)",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct bf5xx_nand_platform bf5xx_nand_platform = {
+ .data_width = NFC_NWIDTH_8,
+ .partitions = partition_info,
+ .nr_partitions = ARRAY_SIZE(partition_info),
+ .rd_dly = 3,
+ .wr_dly = 3,
+};
+
+static struct resource bf5xx_nand_resources[] = {
+ {
+ .start = NFC_CTL,
+ .end = NFC_DATA_RD + 2,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = CH_NFC,
+ .end = CH_NFC,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bf5xx_nand_device = {
+ .name = "bf5xx-nand",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bf5xx_nand_resources),
+ .resource = bf5xx_nand_resources,
+ .dev = {
+ .platform_data = &bf5xx_nand_platform,
+ },
+};
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+ .name = "rtc-bfin",
+ .id = -1,
+};
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#include <linux/bfin_mac.h>
+static const unsigned short bfin_mac_peripherals[] = P_RMII0;
+
+static struct bfin_phydev_platform_data bfin_phydev_data[] = {
+ {
+ .addr = 1,
+ .irq = IRQ_MAC_PHYINT,
+ },
+};
+
+static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
+ .phydev_number = 1,
+ .phydev_data = bfin_phydev_data,
+ .phy_mode = PHY_INTERFACE_MODE_RMII,
+ .mac_peripherals = bfin_mac_peripherals,
+};
+
+static struct platform_device bfin_mii_bus = {
+ .name = "bfin_mii_bus",
+ .dev = {
+ .platform_data = &bfin_mii_bus_data,
+ }
+};
+
+static struct platform_device bfin_mac_device = {
+ .name = "bfin_mac",
+ .dev = {
+ .platform_data = &bfin_mii_bus,
+ }
+};
+#endif
+
+
+#if defined(CONFIG_MTD_M25P80) \
+ || defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+ {
+ .name = "bootloader(spi)",
+ .size = 0x00040000,
+ .offset = 0,
+ .mask_flags = MTD_CAP_ROM
+ }, {
+ .name = "linux kernel(spi)",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ }
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+ .name = "m25p80",
+ .parts = bfin_spi_flash_partitions,
+ .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+ .type = "m25p16",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+static struct bfin5xx_spi_chip spidev_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+static struct platform_device bfin_i2s = {
+ .name = "bfin-i2s",
+ .id = CONFIG_SND_BF5XX_SPORT_NUM,
+ /* TODO: add platform data here */
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+static struct platform_device bfin_tdm = {
+ .name = "bfin-tdm",
+ .id = CONFIG_SND_BF5XX_SPORT_NUM,
+ /* TODO: add platform data here */
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) \
+ || defined(CONFIG_MTD_M25P80_MODULE)
+ {
+ /* the modalias must be the same as spi device driver name */
+ .modalias = "m25p80", /* Name of spi_driver for this device */
+ .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0, /* Framework bus number */
+ .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
+ .platform_data = &bfin_spi_flash_data,
+ .controller_data = &spi_flash_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+ {
+ .modalias = "ad183x",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 4,
+ .controller_data = &ad1836_spi_chip_info,
+ },
+#endif
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+ {
+ .modalias = "mmc_spi",
+ .max_speed_hz = 30000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = GPIO_PH3 + MAX_CTRL_CS,
+ .controller_data = &mmc_spi_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+ {
+ .modalias = "spidev",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1,
+ .controller_data = &spidev_chip_info,
+ },
+#endif
+};
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+ .num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS,
+ .enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = IRQ_SPI,
+ .end = IRQ_SPI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
+ .dev = {
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
+ },
+};
+#endif /* spi master and devices */
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
+ {
+ .start = UART0_THR,
+ .end = UART0_GCTL+2,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART0_RX,
+ .end = IRQ_UART0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_UART0_ERROR,
+ .end = IRQ_UART0_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART0_TX,
+ .end = CH_UART0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ {
+ .start = CH_UART0_RX,
+ .end = CH_UART0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+ P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+ .name = "bfin-uart",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+ .resource = bfin_uart0_resources,
+ .dev = {
+ .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+ },
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
+ {
+ .start = UART1_THR,
+ .end = UART1_GCTL+2,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART1_RX,
+ .end = IRQ_UART1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_UART1_ERROR,
+ .end = IRQ_UART1_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART1_TX,
+ .end = CH_UART1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ {
+ .start = CH_UART1_RX,
+ .end = CH_UART1_RX,
+ .flags = IORESOURCE_DMA,
+ },
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+ { /* CTS pin */
+ .start = GPIO_PF9,
+ .end = GPIO_PF9,
+ .flags = IORESOURCE_IO,
+ },
+ { /* RTS pin */
+ .start = GPIO_PF10,
+ .end = GPIO_PF10,
+ .flags = IORESOURCE_IO,
+ },
+#endif
+};
+
+unsigned short bfin_uart1_peripherals[] = {
+ P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
+ .name = "bfin-uart",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+ .resource = bfin_uart1_resources,
+ .dev = {
+ .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+ },
+};
+#endif
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+static struct resource bfin_sir0_resources[] = {
+ {
+ .start = 0xFFC00400,
+ .end = 0xFFC004FF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART0_RX,
+ .end = IRQ_UART0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART0_RX,
+ .end = CH_UART0_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device bfin_sir0_device = {
+ .name = "bfin_sir",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_sir0_resources),
+ .resource = bfin_sir0_resources,
+};
+#endif
+#ifdef CONFIG_BFIN_SIR1
+static struct resource bfin_sir1_resources[] = {
+ {
+ .start = 0xFFC02000,
+ .end = 0xFFC020FF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART1_RX,
+ .end = IRQ_UART1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART1_RX,
+ .end = CH_UART1_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device bfin_sir1_device = {
+ .name = "bfin_sir",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_sir1_resources),
+ .resource = bfin_sir1_resources,
+};
+#endif
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7160) || defined(CONFIG_TOUCHSCREEN_AD7160_MODULE)
+#include <linux/input/ad7160.h>
+static const struct ad7160_platform_data bfin_ad7160_ts_info = {
+ .sensor_x_res = 854,
+ .sensor_y_res = 480,
+ .pressure = 100,
+ .filter_coef = 3,
+ .coord_pref = AD7160_ORIG_TOP_LEFT,
+ .first_touch_window = 5,
+ .move_window = 3,
+ .event_cabs = AD7160_EMIT_ABS_MT_TRACKING_ID |
+ AD7160_EMIT_ABS_MT_PRESSURE |
+ AD7160_TRACKING_ID_ASCENDING,
+ .finger_act_ctrl = 0x64,
+ .haptic_effect1_ctrl = AD7160_HAPTIC_SLOT_A(60) |
+ AD7160_HAPTIC_SLOT_A_LVL_HIGH |
+ AD7160_HAPTIC_SLOT_B(60) |
+ AD7160_HAPTIC_SLOT_B_LVL_LOW,
+
+ .haptic_effect2_ctrl = AD7160_HAPTIC_SLOT_A(20) |
+ AD7160_HAPTIC_SLOT_A_LVL_HIGH |
+ AD7160_HAPTIC_SLOT_B(80) |
+ AD7160_HAPTIC_SLOT_B_LVL_LOW |
+ AD7160_HAPTIC_SLOT_C(120) |
+ AD7160_HAPTIC_SLOT_C_LVL_HIGH |
+ AD7160_HAPTIC_SLOT_D(30) |
+ AD7160_HAPTIC_SLOT_D_LVL_LOW,
+};
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+ [0] = {
+ .start = TWI0_REGBASE,
+ .end = TWI0_REGBASE,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_TWI,
+ .end = IRQ_TWI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+ .name = "i2c-bfin-twi",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_twi0_resource),
+ .resource = bfin_twi0_resource,
+};
+#endif
+
+static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
+#if defined(CONFIG_TOUCHSCREEN_AD7160) || defined(CONFIG_TOUCHSCREEN_AD7160_MODULE)
+ {
+ I2C_BOARD_INFO("ad7160", 0x33),
+ .irq = IRQ_PH1,
+ .platform_data = (void *)&bfin_ad7160_ts_info,
+ },
+#endif
+};
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+static struct resource bfin_sport0_uart_resources[] = {
+ {
+ .start = SPORT0_TCR1,
+ .end = SPORT0_MRCS3+4,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_SPORT0_RX,
+ .end = IRQ_SPORT0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_SPORT0_ERROR,
+ .end = IRQ_SPORT0_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+unsigned short bfin_sport0_peripherals[] = {
+ P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
+ P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
+};
+
+static struct platform_device bfin_sport0_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
+ .resource = bfin_sport0_uart_resources,
+ .dev = {
+ .platform_data = &bfin_sport0_peripherals, /* Passed to driver */
+ },
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+static struct resource bfin_sport1_uart_resources[] = {
+ {
+ .start = SPORT1_TCR1,
+ .end = SPORT1_MRCS3+4,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_SPORT1_RX,
+ .end = IRQ_SPORT1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_SPORT1_ERROR,
+ .end = IRQ_SPORT1_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+unsigned short bfin_sport1_peripherals[] = {
+ P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
+ P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
+ .resource = bfin_sport1_uart_resources,
+ .dev = {
+ .platform_data = &bfin_sport1_peripherals, /* Passed to driver */
+ },
+};
+#endif
+#endif
+
+#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#include <asm/bfin_rotary.h>
+
+static struct bfin_rotary_platform_data bfin_rotary_data = {
+ /*.rotary_up_key = KEY_UP,*/
+ /*.rotary_down_key = KEY_DOWN,*/
+ .rotary_rel_code = REL_WHEEL,
+ .rotary_button_key = KEY_ENTER,
+ .debounce = 10, /* 0..17 */
+ .mode = ROT_QUAD_ENC | ROT_DEBE,
+};
+
+static struct resource bfin_rotary_resources[] = {
+ {
+ .start = IRQ_CNT,
+ .end = IRQ_CNT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_rotary_device = {
+ .name = "bfin-rotary",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_rotary_resources),
+ .resource = bfin_rotary_resources,
+ .dev = {
+ .platform_data = &bfin_rotary_data,
+ },
+};
+#endif
+
+static const unsigned int cclk_vlev_datasheet[] = {
+ VRPAIR(VLEV_100, 400000000),
+ VRPAIR(VLEV_105, 426000000),
+ VRPAIR(VLEV_110, 500000000),
+ VRPAIR(VLEV_115, 533000000),
+ VRPAIR(VLEV_120, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+ .tuple_tab = cclk_vlev_datasheet,
+ .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+ .vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+ .name = "bfin dpmc",
+ .dev = {
+ .platform_data = &bfin_dmpc_vreg_data,
+ },
+};
+
+static struct platform_device *stamp_devices[] __initdata = {
+
+ &bfin_dpmc,
+
+#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+ &bf5xx_nand_device,
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+ &rtc_device,
+#endif
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+ &musb_device,
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+ &bfin_mii_bus,
+ &bfin_mac_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ &bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ &bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_FB_BFIN_RA158Z) || defined(CONFIG_FB_BFIN_RA158Z_MODULE)
+ &bf52x_ra158z_device,
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+ &bfin_sir0_device,
+#endif
+#ifdef CONFIG_BFIN_SIR1
+ &bfin_sir1_device,
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+ &i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+ &bfin_sport0_uart_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+ &bfin_sport1_uart_device,
+#endif
+#endif
+
+#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+ &bfin_rotary_device,
+#endif
+
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+ &ad7160eval_flash_device,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+ &bfin_i2s,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+ &bfin_tdm,
+#endif
+};
+
+static int __init ad7160eval_init(void)
+{
+ printk(KERN_INFO "%s(): registering device resources\n", __func__);
+ i2c_register_board_info(0, bfin_i2c_board_info,
+ ARRAY_SIZE(bfin_i2c_board_info));
+ platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
+ spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+ return 0;
+}
+
+arch_initcall(ad7160eval_init);
+
+static struct platform_device *ad7160eval_early_devices[] __initdata = {
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ &bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+ &bfin_sport0_uart_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+ &bfin_sport1_uart_device,
+#endif
+#endif
+};
+
+void __init native_machine_early_platform_add_devices(void)
+{
+ printk(KERN_INFO "register early platform devices\n");
+ early_platform_add_devices(ad7160eval_early_devices,
+ ARRAY_SIZE(ad7160eval_early_devices));
+}
+
+void native_machine_restart(char *cmd)
+{
+ /* workaround reboot hang when booting from SPI */
+ if ((bfin_read_SYSCR() & 0x7) == 0x3)
+ bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
+}
+
+void bfin_get_ether_addr(char *addr)
+{
+ /* the MAC is stored in OTP memory page 0xDF */
+ u32 ret;
+ u64 otp_mac;
+ u32 (*otp_read)(u32 page, u32 flags, u64 *page_content) = (void *)0xEF00001A;
+
+ ret = otp_read(0xDF, 0x00, &otp_mac);
+ if (!(ret & 0x1)) {
+ char *otp_mac_p = (char *)&otp_mac;
+ for (ret = 0; ret < 6; ++ret)
+ addr[ret] = otp_mac_p[5 - ret];
+ }
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-11-20 13:33:18 +0000