diff options
Diffstat (limited to 'Documentation/ABI')
| -rw-r--r-- | Documentation/ABI/stable/sysfs-bus-usb | 142 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio | 19 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 | 8 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 | 2 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-usb | 89 |
5 files changed, 162 insertions, 98 deletions
diff --git a/Documentation/ABI/stable/sysfs-bus-usb b/Documentation/ABI/stable/sysfs-bus-usb new file mode 100644 index 00000000000..2be603c52a2 --- /dev/null +++ b/Documentation/ABI/stable/sysfs-bus-usb @@ -0,0 +1,142 @@ +What: /sys/bus/usb/devices/.../power/persist +Date: May 2007 +KernelVersion: 2.6.23 +Contact: Alan Stern <stern@rowland.harvard.edu> +Description: + If CONFIG_USB_PERSIST is set, then each USB device directory + will contain a file named power/persist. The file holds a + boolean value (0 or 1) indicating whether or not the + "USB-Persist" facility is enabled for the device. Since the + facility is inherently dangerous, it is disabled by default + for all devices except hubs. For more information, see + Documentation/usb/persist.txt. + +What: /sys/bus/usb/devices/.../power/autosuspend +Date: March 2007 +KernelVersion: 2.6.21 +Contact: Alan Stern <stern@rowland.harvard.edu> +Description: + Each USB device directory will contain a file named + power/autosuspend. This file holds the time (in seconds) + the device must be idle before it will be autosuspended. + 0 means the device will be autosuspended as soon as + possible. Negative values will prevent the device from + being autosuspended at all, and writing a negative value + will resume the device if it is already suspended. + + The autosuspend delay for newly-created devices is set to + the value of the usbcore.autosuspend module parameter. + +What: /sys/bus/usb/device/.../power/connected_duration +Date: January 2008 +KernelVersion: 2.6.25 +Contact: Sarah Sharp <sarah.a.sharp@intel.com> +Description: + If CONFIG_PM_RUNTIME is enabled then this file + is present. When read, it returns the total time (in msec) + that the USB device has been connected to the machine. This + file is read-only. +Users: + PowerTOP <power@bughost.org> + http://www.lesswatts.org/projects/powertop/ + +What: /sys/bus/usb/device/.../power/active_duration +Date: January 2008 +KernelVersion: 2.6.25 +Contact: Sarah Sharp <sarah.a.sharp@intel.com> +Description: + If CONFIG_PM_RUNTIME is enabled then this file + is present. When read, it returns the total time (in msec) + that the USB device has been active, i.e. not in a suspended + state. This file is read-only. + + Tools can use this file and the connected_duration file to + compute the percentage of time that a device has been active. + For example, + echo $((100 * `cat active_duration` / `cat connected_duration`)) + will give an integer percentage. Note that this does not + account for counter wrap. +Users: + PowerTOP <power@bughost.org> + http://www.lesswatts.org/projects/powertop/ + +What: /sys/bus/usb/devices/<busnum>-<port[.port]>...:<config num>-<interface num>/supports_autosuspend +Date: January 2008 +KernelVersion: 2.6.27 +Contact: Sarah Sharp <sarah.a.sharp@intel.com> +Description: + When read, this file returns 1 if the interface driver + for this interface supports autosuspend. It also + returns 1 if no driver has claimed this interface, as an + unclaimed interface will not stop the device from being + autosuspended if all other interface drivers are idle. + The file returns 0 if autosuspend support has not been + added to the driver. +Users: + USB PM tool + git://git.moblin.org/users/sarah/usb-pm-tool/ + +What: /sys/bus/usb/device/.../avoid_reset_quirk +Date: December 2009 +Contact: Oliver Neukum <oliver@neukum.org> +Description: + Writing 1 to this file tells the kernel that this + device will morph into another mode when it is reset. + Drivers will not use reset for error handling for + such devices. +Users: + usb_modeswitch + +What: /sys/bus/usb/devices/.../devnum +KernelVersion: since at least 2.6.18 +Description: + Device address on the USB bus. +Users: + libusb + +What: /sys/bus/usb/devices/.../bConfigurationValue +KernelVersion: since at least 2.6.18 +Description: + bConfigurationValue of the *active* configuration for the + device. Writing 0 or -1 to bConfigurationValue will reset the + active configuration (unconfigure the device). Writing + another value will change the active configuration. + + Note that some devices, in violation of the USB spec, have a + configuration with a value equal to 0. Writing 0 to + bConfigurationValue for these devices will install that + configuration, rather then unconfigure the device. + + Writing -1 will always unconfigure the device. +Users: + libusb + +What: /sys/bus/usb/devices/.../busnum +KernelVersion: 2.6.22 +Description: + Bus-number of the USB-bus the device is connected to. +Users: + libusb + +What: /sys/bus/usb/devices/.../descriptors +KernelVersion: 2.6.26 +Description: + Binary file containing cached descriptors of the device. The + binary data consists of the device descriptor followed by the + descriptors for each configuration of the device. + Note that the wTotalLength of the config descriptors can not + be trusted, as the device may have a smaller config descriptor + than it advertises. The bLength field of each (sub) descriptor + can be trusted, and can be used to seek forward one (sub) + descriptor at a time until the next config descriptor is found. + All descriptors read from this file are in bus-endian format +Users: + libusb + +What: /sys/bus/usb/devices/.../speed +KernelVersion: since at least 2.6.18 +Description: + Speed the device is connected with to the usb-host in + Mbit / second. IE one of 1.5 / 12 / 480 / 5000. +Users: + libusb diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index dda81ffae5c..39c8de0e53d 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -351,6 +351,7 @@ Description: 6kohm_to_gnd: connected to ground via a 6kOhm resistor, 20kohm_to_gnd: connected to ground via a 20kOhm resistor, 100kohm_to_gnd: connected to ground via an 100kOhm resistor, + 500kohm_to_gnd: connected to ground via a 500kOhm resistor, three_state: left floating. For a list of available output power down options read outX_powerdown_mode_available. If Y is not present the @@ -792,3 +793,21 @@ Contact: linux-iio@vger.kernel.org Description: This attribute is used to read the amount of quadrature error present in the device at a given time. + +What: /sys/.../iio:deviceX/in_accelX_power_mode +KernelVersion: 3.11 +Contact: linux-iio@vger.kernel.org +Description: + Specifies the chip power mode. + low_noise: reduce noise level from ADC, + low_power: enable low current consumption. + For a list of available output power modes read + in_accel_power_mode_available. + +What: /sys/bus/iio/devices/iio:deviceX/store_eeprom +KernelVersion: 3.4.0 +Contact: linux-iio@vger.kernel.org +Description: + Writing '1' stores the current device configuration into + on-chip EEPROM. After power-up or chip reset the device will + automatically load the saved configuration. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 b/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 index 2ce9c3f68ee..a91aeabe7b2 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 +++ b/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 @@ -18,14 +18,6 @@ Description: Reading returns either '1' or '0'. '1' means that the pllY is locked. -What: /sys/bus/iio/devices/iio:deviceX/store_eeprom -KernelVersion: 3.4.0 -Contact: linux-iio@vger.kernel.org -Description: - Writing '1' stores the current device configuration into - on-chip EEPROM. After power-up or chip reset the device will - automatically load the saved configuration. - What: /sys/bus/iio/devices/iio:deviceX/sync_dividers KernelVersion: 3.4.0 Contact: linux-iio@vger.kernel.org diff --git a/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 b/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 index d89aded01c5..1254457a726 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 +++ b/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 @@ -18,4 +18,4 @@ Description: adjust the reference frequency accordingly. The value written has no effect until out_altvoltageY_frequency is updated. Consider to use out_altvoltageY_powerdown to power - down the PLL and it's RFOut buffers during REFin changes. + down the PLL and its RFOut buffers during REFin changes. diff --git a/Documentation/ABI/testing/sysfs-bus-usb b/Documentation/ABI/testing/sysfs-bus-usb index 9759b8c9133..1430f584b26 100644 --- a/Documentation/ABI/testing/sysfs-bus-usb +++ b/Documentation/ABI/testing/sysfs-bus-usb @@ -1,81 +1,3 @@ -What: /sys/bus/usb/devices/.../power/autosuspend -Date: March 2007 -KernelVersion: 2.6.21 -Contact: Alan Stern <stern@rowland.harvard.edu> -Description: - Each USB device directory will contain a file named - power/autosuspend. This file holds the time (in seconds) - the device must be idle before it will be autosuspended. - 0 means the device will be autosuspended as soon as - possible. Negative values will prevent the device from - being autosuspended at all, and writing a negative value - will resume the device if it is already suspended. - - The autosuspend delay for newly-created devices is set to - the value of the usbcore.autosuspend module parameter. - -What: /sys/bus/usb/devices/.../power/persist -Date: May 2007 -KernelVersion: 2.6.23 -Contact: Alan Stern <stern@rowland.harvard.edu> -Description: - If CONFIG_USB_PERSIST is set, then each USB device directory - will contain a file named power/persist. The file holds a - boolean value (0 or 1) indicating whether or not the - "USB-Persist" facility is enabled for the device. Since the - facility is inherently dangerous, it is disabled by default - for all devices except hubs. For more information, see - Documentation/usb/persist.txt. - -What: /sys/bus/usb/device/.../power/connected_duration -Date: January 2008 -KernelVersion: 2.6.25 -Contact: Sarah Sharp <sarah.a.sharp@intel.com> -Description: - If CONFIG_PM_RUNTIME is enabled then this file - is present. When read, it returns the total time (in msec) - that the USB device has been connected to the machine. This - file is read-only. -Users: - PowerTOP <power@bughost.org> - http://www.lesswatts.org/projects/powertop/ - -What: /sys/bus/usb/device/.../power/active_duration -Date: January 2008 -KernelVersion: 2.6.25 -Contact: Sarah Sharp <sarah.a.sharp@intel.com> -Description: - If CONFIG_PM_RUNTIME is enabled then this file - is present. When read, it returns the total time (in msec) - that the USB device has been active, i.e. not in a suspended - state. This file is read-only. - - Tools can use this file and the connected_duration file to - compute the percentage of time that a device has been active. - For example, - echo $((100 * `cat active_duration` / `cat connected_duration`)) - will give an integer percentage. Note that this does not - account for counter wrap. -Users: - PowerTOP <power@bughost.org> - http://www.lesswatts.org/projects/powertop/ - -What: /sys/bus/usb/device/<busnum>-<devnum>...:<config num>-<interface num>/supports_autosuspend -Date: January 2008 -KernelVersion: 2.6.27 -Contact: Sarah Sharp <sarah.a.sharp@intel.com> -Description: - When read, this file returns 1 if the interface driver - for this interface supports autosuspend. It also - returns 1 if no driver has claimed this interface, as an - unclaimed interface will not stop the device from being - autosuspended if all other interface drivers are idle. - The file returns 0 if autosuspend support has not been - added to the driver. -Users: - USB PM tool - git://git.moblin.org/users/sarah/usb-pm-tool/ - What: /sys/bus/usb/device/.../authorized Date: July 2008 KernelVersion: 2.6.26 @@ -172,17 +94,6 @@ Description: device IDs, exactly like reading from the entry "/sys/bus/usb/drivers/.../new_id" -What: /sys/bus/usb/device/.../avoid_reset_quirk -Date: December 2009 -Contact: Oliver Neukum <oliver@neukum.org> -Description: - Writing 1 to this file tells the kernel that this - device will morph into another mode when it is reset. - Drivers will not use reset for error handling for - such devices. -Users: - usb_modeswitch - What: /sys/bus/usb/devices/.../power/usb2_hardware_lpm Date: September 2011 Contact: Andiry Xu <andiry.xu@amd.com> |