summaryrefslogtreecommitdiffstats
path: root/Documentation/DocBook/media/v4l/dev-subdev.xml
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/DocBook/media/v4l/dev-subdev.xml')
-rw-r--r--Documentation/DocBook/media/v4l/dev-subdev.xml36
1 files changed, 18 insertions, 18 deletions
diff --git a/Documentation/DocBook/media/v4l/dev-subdev.xml b/Documentation/DocBook/media/v4l/dev-subdev.xml
index 4afcbbec5ed..a3d9dd09326 100644
--- a/Documentation/DocBook/media/v4l/dev-subdev.xml
+++ b/Documentation/DocBook/media/v4l/dev-subdev.xml
@@ -276,7 +276,7 @@
</para>
</section>
- <section>
+ <section id="v4l2-subdev-selections">
<title>Selections: cropping, scaling and composition</title>
<para>Many sub-devices support cropping frames on their input or output
@@ -290,8 +290,8 @@
size. Both the coordinates and sizes are expressed in pixels.</para>
<para>As for pad formats, drivers store try and active
- rectangles for the selection targets of ACTUAL type <xref
- linkend="v4l2-subdev-selection-targets">.</xref></para>
+ rectangles for the selection targets <xref
+ linkend="v4l2-selections-common" />.</para>
<para>On sink pads, cropping is applied relative to the
current pad format. The pad format represents the image size as
@@ -308,7 +308,7 @@
<para>Scaling support is optional. When supported by a subdev,
the crop rectangle on the subdev's sink pad is scaled to the
size configured using the &VIDIOC-SUBDEV-S-SELECTION; IOCTL
- using <constant>V4L2_SUBDEV_SEL_COMPOSE_ACTUAL</constant>
+ using <constant>V4L2_SEL_TGT_COMPOSE</constant>
selection target on the same pad. If the subdev supports scaling
but not composing, the top and left values are not used and must
always be set to zero.</para>
@@ -323,32 +323,32 @@
<para>The drivers should always use the closest possible
rectangle the user requests on all selection targets, unless
specifically told otherwise.
- <constant>V4L2_SUBDEV_SEL_FLAG_SIZE_GE</constant> and
- <constant>V4L2_SUBDEV_SEL_FLAG_SIZE_LE</constant> flags may be
+ <constant>V4L2_SEL_FLAG_GE</constant> and
+ <constant>V4L2_SEL_FLAG_LE</constant> flags may be
used to round the image size either up or down. <xref
- linkend="v4l2-subdev-selection-flags"></xref></para>
+ linkend="v4l2-selection-flags" /></para>
</section>
<section>
<title>Types of selection targets</title>
<section>
- <title>ACTUAL targets</title>
+ <title>Actual targets</title>
- <para>ACTUAL targets reflect the actual hardware configuration
- at any point of time. There is a BOUNDS target
- corresponding to every ACTUAL.</para>
+ <para>Actual targets (without a postfix) reflect the actual
+ hardware configuration at any point of time. There is a BOUNDS
+ target corresponding to every actual target.</para>
</section>
<section>
<title>BOUNDS targets</title>
- <para>BOUNDS targets is the smallest rectangle that contains
- all valid ACTUAL rectangles. It may not be possible to set the
- ACTUAL rectangle as large as the BOUNDS rectangle, however.
- This may be because e.g. a sensor's pixel array is not
- rectangular but cross-shaped or round. The maximum size may
- also be smaller than the BOUNDS rectangle.</para>
+ <para>BOUNDS targets is the smallest rectangle that contains all
+ valid actual rectangles. It may not be possible to set the actual
+ rectangle as large as the BOUNDS rectangle, however. This may be
+ because e.g. a sensor's pixel array is not rectangular but
+ cross-shaped or round. The maximum size may also be smaller than the
+ BOUNDS rectangle.</para>
</section>
</section>
@@ -362,7 +362,7 @@
performed by the user: the changes made will be propagated to
any subsequent stages. If this behaviour is not desired, the
user must set
- <constant>V4L2_SUBDEV_SEL_FLAG_KEEP_CONFIG</constant> flag. This
+ <constant>V4L2_SEL_FLAG_KEEP_CONFIG</constant> flag. This
flag causes no propagation of the changes are allowed in any
circumstances. This may also cause the accessed rectangle to be
adjusted by the driver, depending on the properties of the