diff options
Diffstat (limited to 'Documentation/arm')
| -rw-r--r-- | Documentation/arm/IXP4xx | 2 | ||||
| -rw-r--r-- | Documentation/arm/Samsung-S3C24XX/Overview.txt | 35 | ||||
| -rw-r--r-- | Documentation/arm/Samsung-S3C24XX/S3C2412.txt | 120 | ||||
| -rw-r--r-- | Documentation/arm/Samsung-S3C24XX/S3C2413.txt | 21 | ||||
| -rw-r--r-- | Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen | 61 | ||||
| -rw-r--r-- | Documentation/arm/Sharp-LH/LCDPanels | 59 |
6 files changed, 276 insertions, 22 deletions
diff --git a/Documentation/arm/IXP4xx b/Documentation/arm/IXP4xx index d4c6d3aa0c2..43edb4ecf27 100644 --- a/Documentation/arm/IXP4xx +++ b/Documentation/arm/IXP4xx @@ -85,7 +85,7 @@ IXP4xx provides two methods of accessing PCI memory space: 2) If > 64MB of memory space is required, the IXP4xx can be configured to use indirect registers to access PCI This allows for up to 128MB (0x48000000 to 0x4fffffff) of memory on the bus. - The disadvantadge of this is that every PCI access requires + The disadvantage of this is that every PCI access requires three local register accesses plus a spinlock, but in some cases the performance hit is acceptable. In addition, you cannot mmap() PCI devices in this case due to the indirect nature diff --git a/Documentation/arm/Samsung-S3C24XX/Overview.txt b/Documentation/arm/Samsung-S3C24XX/Overview.txt index 8c6ee684174..3e46d2a3115 100644 --- a/Documentation/arm/Samsung-S3C24XX/Overview.txt +++ b/Documentation/arm/Samsung-S3C24XX/Overview.txt @@ -7,11 +7,13 @@ Introduction ------------ The Samsung S3C24XX range of ARM9 System-on-Chip CPUs are supported - by the 's3c2410' architecture of ARM Linux. Currently the S3C2410 and - the S3C2440 are supported CPUs. + by the 's3c2410' architecture of ARM Linux. Currently the S3C2410, + S3C2440 and S3C2442 devices are supported. Support for the S3C2400 series is in progress. + Support for the S3C2412 and S3C2413 CPUs is being merged. + Configuration ------------- @@ -43,9 +45,18 @@ Machines Samsung's own development board, geared for PDA work. + Samsung/Aiji SMDK2412 + + The S3C2412 version of the SMDK2440. + + Samsung/Aiji SMDK2413 + + The S3C2412 version of the SMDK2440. + Samsung/Meritech SMDK2440 - The S3C2440 compatible version of the SMDK2440 + The S3C2440 compatible version of the SMDK2440, which has the + option of an S3C2440 or S3C2442 CPU module. Thorcom VR1000 @@ -211,24 +222,6 @@ Port Contributors Lucas Correia Villa Real (S3C2400 port) -Document Changes ----------------- - - 05 Sep 2004 - BJD - Added Document Changes section - 05 Sep 2004 - BJD - Added Klaus Fetscher to list of contributors - 25 Oct 2004 - BJD - Added Dimitry Andric to list of contributors - 25 Oct 2004 - BJD - Updated the MTD from the 2.6.9 merge - 21 Jan 2005 - BJD - Added rx3715, added Shannon to contributors - 10 Feb 2005 - BJD - Added Guillaume Gourat to contributors - 02 Mar 2005 - BJD - Added SMDK2440 to list of machines - 06 Mar 2005 - BJD - Added Christer Weinigel - 08 Mar 2005 - BJD - Added LCVR to list of people, updated introduction - 08 Mar 2005 - BJD - Added section on adding machines - 09 Sep 2005 - BJD - Added section on platform data - 11 Feb 2006 - BJD - Added I2C, RTC and Watchdog sections - 11 Feb 2006 - BJD - Added Osiris machine, and S3C2400 information - - Document Author --------------- diff --git a/Documentation/arm/Samsung-S3C24XX/S3C2412.txt b/Documentation/arm/Samsung-S3C24XX/S3C2412.txt new file mode 100644 index 00000000000..cb82a7fc790 --- /dev/null +++ b/Documentation/arm/Samsung-S3C24XX/S3C2412.txt @@ -0,0 +1,120 @@ + S3C2412 ARM Linux Overview + ========================== + +Introduction +------------ + + The S3C2412 is part of the S3C24XX range of ARM9 System-on-Chip CPUs + from Samsung. This part has an ARM926-EJS core, capable of running up + to 266MHz (see data-sheet for more information) + + +Clock +----- + + The core clock code provides a set of clocks to the drivers, and allows + for source selection and a number of other features. + + +Power +----- + + No support for suspend/resume to RAM in the current system. + + +DMA +--- + + No current support for DMA. + + +GPIO +---- + + There is support for setting the GPIO to input/output/special function + and reading or writing to them. + + +UART +---- + + The UART hardware is similar to the S3C2440, and is supported by the + s3c2410 driver in the drivers/serial directory. + + +NAND +---- + + The NAND hardware is similar to the S3C2440, and is supported by the + s3c2410 driver in the drivers/mtd/nand directory. + + +USB Host +-------- + + The USB hardware is similar to the S3C2410, with extended clock source + control. The OHCI portion is supported by the ohci-s3c2410 driver, and + the clock control selection is supported by the core clock code. + + +USB Device +---------- + + No current support in the kernel + + +IRQs +---- + + All the standard, and external interrupt sources are supported. The + extra sub-sources are not yet supported. + + +RTC +--- + + The RTC hardware is similar to the S3C2410, and is supported by the + s3c2410-rtc driver. + + +Watchdog +-------- + + The watchdog harware is the same as the S3C2410, and is supported by + the s3c2410_wdt driver. + + +MMC/SD/SDIO +----------- + + No current support for the MMC/SD/SDIO block. + +IIC +--- + + The IIC hardware is the same as the S3C2410, and is supported by the + i2c-s3c24xx driver. + + +IIS +--- + + No current support for the IIS interface. + + +SPI +--- + + No current support for the SPI interfaces. + + +ATA +--- + + No current support for the on-board ATA block. + + +Document Author +--------------- + +Ben Dooks, (c) 2006 Simtec Electronics diff --git a/Documentation/arm/Samsung-S3C24XX/S3C2413.txt b/Documentation/arm/Samsung-S3C24XX/S3C2413.txt new file mode 100644 index 00000000000..ab2a88858f1 --- /dev/null +++ b/Documentation/arm/Samsung-S3C24XX/S3C2413.txt @@ -0,0 +1,21 @@ + S3C2413 ARM Linux Overview + ========================== + +Introduction +------------ + + The S3C2413 is an extended version of the S3C2412, with an camera + interface and mobile DDR memory support. See the S3C2412 support + documentation for more information. + + +Camera Interface +--------------- + + This block is currently not supported. + + +Document Author +--------------- + +Ben Dooks, (c) 2006 Simtec Electronics diff --git a/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen b/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen new file mode 100644 index 00000000000..1e6a23fdf2f --- /dev/null +++ b/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen @@ -0,0 +1,61 @@ +README on the ADC/Touchscreen Controller +======================================== + +The LH79524 and LH7A404 include a built-in Analog to Digital +controller (ADC) that is used to process input from a touchscreen. +The driver only implements a four-wire touch panel protocol. + +The touchscreen driver is maintenance free except for the pen-down or +touch threshold. Some resistive displays and board combinations may +require tuning of this threshold. The driver exposes some of it's +internal state in the sys filesystem. If the kernel is configured +with it, CONFIG_SYSFS, and sysfs is mounted at /sys, there will be a +directory + + /sys/devices/platform/adc-lh7.0 + +containing these files. + + -r--r--r-- 1 root root 4096 Jan 1 00:00 samples + -rw-r--r-- 1 root root 4096 Jan 1 00:00 threshold + -r--r--r-- 1 root root 4096 Jan 1 00:00 threshold_range + +The threshold is the current touch threshold. It defaults to 750 on +most targets. + + # cat threshold + 750 + +The threshold_range contains the range of valid values for the +threshold. Values outside of this range will be silently ignored. + + # cat threshold_range + 0 1023 + +To change the threshold, write a value to the threshold file. + + # echo 500 > threshold + # cat threshold + 500 + +The samples file contains the most recently sampled values from the +ADC. There are 12. Below are typical of the last sampled values when +the pen has been released. The first two and last two samples are for +detecting whether or not the pen is down. The third through sixth are +X coordinate samples. The seventh through tenth are Y coordinate +samples. + + # cat samples + 1023 1023 0 0 0 0 530 529 530 529 1023 1023 + +To determine a reasonable threshold, press on the touch panel with an +appropriate stylus and read the values from samples. + + # cat samples + 1023 676 92 103 101 102 855 919 922 922 1023 679 + +The first and eleventh samples are discarded. Thus, the important +values are the second and twelfth which are used to determine if the +pen is down. When both are below the threshold, the driver registers +that the pen is down. When either is above the threshold, it +registers then pen is up. diff --git a/Documentation/arm/Sharp-LH/LCDPanels b/Documentation/arm/Sharp-LH/LCDPanels new file mode 100644 index 00000000000..fb1b21c2f2f --- /dev/null +++ b/Documentation/arm/Sharp-LH/LCDPanels @@ -0,0 +1,59 @@ +README on the LCD Panels +======================== + +Configuration options for several LCD panels, available from Logic PD, +are included in the kernel source. This README will help you +understand the configuration data and give you some guidance for +adding support for other panels if you wish. + + +lcd-panels.h +------------ + +There is no way, at present, to detect which panel is attached to the +system at runtime. Thus the kernel configuration is static. The file +arch/arm/mach-ld7a40x/lcd-panels.h (or similar) defines all of the +panel specific parameters. + +It should be possible for this data to be shared among several device +families. The current layout may be insufficiently general, but it is +amenable to improvement. + + +PIXEL_CLOCK +----------- + +The panel data sheets will give a range of acceptable pixel clocks. +The fundamental LCDCLK input frequency is divided down by a PCD +constant in field '.tim2'. It may happen that it is impossible to set +the pixel clock within this range. A clock which is too slow will +tend to flicker. For the highest quality image, set the clock as high +as possible. + + +MARGINS +------- + +These values may be difficult to glean from the panel data sheet. In +the case of the Sharp panels, the upper margin is explicitly called +out as a specific number of lines from the top of the frame. The +other values may not matter as much as the panels tend to +automatically center the image. + + +Sync Sense +---------- + +The sense of the hsync and vsync pulses may be called out in the data +sheet. On one panel, the sense of these pulses determine the height +of the visible region on the panel. Most of the Sharp panels use +negative sense sync pulses set by the TIM2_IHS and TIM2_IVS bits in +'.tim2'. + + +Pel Layout +---------- + +The Sharp color TFT panels are all configured for 16 bit direct color +modes. The amba-lcd driver sets the pel mode to 565 for 5 bits of +each red and blue and 6 bits of green. |