diff options
Diffstat (limited to 'Documentation/arm')
| -rw-r--r-- | Documentation/arm/00-INDEX | 2 | ||||
| -rw-r--r-- | Documentation/arm/SA1100/ADSBitsy | 2 | ||||
| -rw-r--r-- | Documentation/arm/SPEAr/overview.txt | 60 | ||||
| -rw-r--r-- | Documentation/arm/Samsung-S3C24XX/GPIO.txt | 81 | ||||
| -rw-r--r-- | Documentation/arm/Samsung-S3C24XX/Overview.txt | 15 | ||||
| -rw-r--r-- | Documentation/arm/Samsung/GPIO.txt | 42 | ||||
| -rw-r--r-- | Documentation/arm/Samsung/Overview.txt | 33 | ||||
| -rw-r--r-- | Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen | 2 |
8 files changed, 222 insertions, 15 deletions
diff --git a/Documentation/arm/00-INDEX b/Documentation/arm/00-INDEX index 82e418d648d..7f5fc3ba9c9 100644 --- a/Documentation/arm/00-INDEX +++ b/Documentation/arm/00-INDEX @@ -20,6 +20,8 @@ Samsung-S3C24XX - S3C24XX ARM Linux Overview Sharp-LH - Linux on Sharp LH79524 and LH7A40X System On a Chip (SOC) +SPEAr + - ST SPEAr platform Linux Overview VFP/ - Release notes for Linux Kernel Vector Floating Point support code empeg/ diff --git a/Documentation/arm/SA1100/ADSBitsy b/Documentation/arm/SA1100/ADSBitsy index 7197a9e958e..f9f62e8c071 100644 --- a/Documentation/arm/SA1100/ADSBitsy +++ b/Documentation/arm/SA1100/ADSBitsy @@ -32,7 +32,7 @@ Notes: - The flash on board is divided into 3 partitions. You should be careful to use flash on board. - It's partition is different from GraphicsClient Plus and GraphicsMaster + Its partition is different from GraphicsClient Plus and GraphicsMaster - 16bpp mode requires a different cable than what ships with the board. Contact ADS or look through the manual to wire your own. Currently, diff --git a/Documentation/arm/SPEAr/overview.txt b/Documentation/arm/SPEAr/overview.txt new file mode 100644 index 00000000000..253a35c6f78 --- /dev/null +++ b/Documentation/arm/SPEAr/overview.txt @@ -0,0 +1,60 @@ + SPEAr ARM Linux Overview + ========================== + +Introduction +------------ + + SPEAr (Structured Processor Enhanced Architecture). + weblink : http://www.st.com/spear + + The ST Microelectronics SPEAr range of ARM9/CortexA9 System-on-Chip CPUs are + supported by the 'spear' platform of ARM Linux. Currently SPEAr300, + SPEAr310, SPEAr320 and SPEAr600 SOCs are supported. Support for the SPEAr13XX + series is in progress. + + Hierarchy in SPEAr is as follows: + + SPEAr (Platform) + - SPEAr3XX (3XX SOC series, based on ARM9) + - SPEAr300 (SOC) + - SPEAr300_EVB (Evaluation Board) + - SPEAr310 (SOC) + - SPEAr310_EVB (Evaluation Board) + - SPEAr320 (SOC) + - SPEAr320_EVB (Evaluation Board) + - SPEAr6XX (6XX SOC series, based on ARM9) + - SPEAr600 (SOC) + - SPEAr600_EVB (Evaluation Board) + - SPEAr13XX (13XX SOC series, based on ARM CORTEXA9) + - SPEAr1300 (SOC) + + Configuration + ------------- + + A generic configuration is provided for each machine, and can be used as the + default by + make spear600_defconfig + make spear300_defconfig + make spear310_defconfig + make spear320_defconfig + + Layout + ------ + + The common files for multiple machine families (SPEAr3XX, SPEAr6XX and + SPEAr13XX) are located in the platform code contained in arch/arm/plat-spear + with headers in plat/. + + Each machine series have a directory with name arch/arm/mach-spear followed by + series name. Like mach-spear3xx, mach-spear6xx and mach-spear13xx. + + Common file for machines of spear3xx family is mach-spear3xx/spear3xx.c and for + spear6xx is mach-spear6xx/spear6xx.c. mach-spear* also contain soc/machine + specific files, like spear300.c, spear310.c, spear320.c and spear600.c. + mach-spear* also contains board specific files for each machine type. + + + Document Author + --------------- + + Viresh Kumar, (c) 2010 ST Microelectronics diff --git a/Documentation/arm/Samsung-S3C24XX/GPIO.txt b/Documentation/arm/Samsung-S3C24XX/GPIO.txt index 2af2cf39915..816d6071669 100644 --- a/Documentation/arm/Samsung-S3C24XX/GPIO.txt +++ b/Documentation/arm/Samsung-S3C24XX/GPIO.txt @@ -12,6 +12,8 @@ Introduction of the s3c2410 GPIO system, please read the Samsung provided data-sheet/users manual to find out the complete list. + See Documentation/arm/Samsung/GPIO.txt for the core implemetation. + GPIOLIB ------- @@ -24,8 +26,60 @@ GPIOLIB listed below will be removed (they may be marked as __deprecated in the near future). - - s3c2410_gpio_getpin - - s3c2410_gpio_setpin + The following functions now either have a s3c_ specific variant + or are merged into gpiolib. See the definitions in + arch/arm/plat-samsung/include/plat/gpio-cfg.h: + + s3c2410_gpio_setpin() gpio_set_value() or gpio_direction_output() + s3c2410_gpio_getpin() gpio_get_value() or gpio_direction_input() + s3c2410_gpio_getirq() gpio_to_irq() + s3c2410_gpio_cfgpin() s3c_gpio_cfgpin() + s3c2410_gpio_getcfg() s3c_gpio_getcfg() + s3c2410_gpio_pullup() s3c_gpio_setpull() + + +GPIOLIB conversion +------------------ + +If you need to convert your board or driver to use gpiolib from the exiting +s3c2410 api, then here are some notes on the process. + +1) If your board is exclusively using an GPIO, say to control peripheral + power, then it will require to claim the gpio with gpio_request() before + it can use it. + + It is recommended to check the return value, with at least WARN_ON() + during initialisation. + +2) The s3c2410_gpio_cfgpin() can be directly replaced with s3c_gpio_cfgpin() + as they have the same arguments, and can either take the pin specific + values, or the more generic special-function-number arguments. + +3) s3c2410_gpio_pullup() changs have the problem that whilst the + s3c2410_gpio_pullup(x, 1) can be easily translated to the + s3c_gpio_setpull(x, S3C_GPIO_PULL_NONE), the s3c2410_gpio_pullup(x, 0) + are not so easy. + + The s3c2410_gpio_pullup(x, 0) case enables the pull-up (or in the case + of some of the devices, a pull-down) and as such the new API distinguishes + between the UP and DOWN case. There is currently no 'just turn on' setting + which may be required if this becomes a problem. + +4) s3c2410_gpio_setpin() can be replaced by gpio_set_value(), the old call + does not implicitly configure the relevant gpio to output. The gpio + direction should be changed before using gpio_set_value(). + +5) s3c2410_gpio_getpin() is replaceable by gpio_get_value() if the pin + has been set to input. It is currently unknown what the behaviour is + when using gpio_get_value() on an output pin (s3c2410_gpio_getpin + would return the value the pin is supposed to be outputting). + +6) s3c2410_gpio_getirq() should be directly replacable with the + gpio_to_irq() call. + +The s3c2410_gpio and gpio_ calls have always operated on the same gpio +numberspace, so there is no problem with converting the gpio numbering +between the calls. Headers @@ -54,6 +108,11 @@ PIN Numbers eg S3C2410_GPA(0) or S3C2410_GPF(1). These defines are used to tell the GPIO functions which pin is to be used. + With the conversion to gpiolib, there is no longer a direct conversion + from gpio pin number to register base address as in earlier kernels. This + is due to the number space required for newer SoCs where the later + GPIOs are not contiguous. + Configuring a pin ----------------- @@ -71,6 +130,8 @@ Configuring a pin which would turn GPA(0) into the lowest Address line A0, and set GPE(8) to be connected to the SDIO/MMC controller's SDDAT1 line. + The s3c_gpio_cfgpin() call is a functional replacement for this call. + Reading the current configuration --------------------------------- @@ -82,6 +143,9 @@ Reading the current configuration The return value will be from the same set of values which can be passed to s3c2410_gpio_cfgpin(). + The s3c_gpio_getcfg() call should be a functional replacement for + this call. + Configuring a pull-up resistor ------------------------------ @@ -95,6 +159,10 @@ Configuring a pull-up resistor Where the to value is zero to set the pull-up off, and 1 to enable the specified pull-up. Any other values are currently undefined. + The s3c_gpio_setpull() offers similar functionality, but with the + ability to encode whether the pull is up or down. Currently there + is no 'just on' state, so up or down must be selected. + Getting the state of a PIN -------------------------- @@ -106,6 +174,9 @@ Getting the state of a PIN This will return either zero or non-zero. Do not count on this function returning 1 if the pin is set. + This call is now implemented by the relevant gpiolib calls, convert + your board or driver to use gpiolib. + Setting the state of a PIN -------------------------- @@ -117,6 +188,9 @@ Setting the state of a PIN Which sets the given pin to the value. Use 0 to write 0, and 1 to set the output to 1. + This call is now implemented by the relevant gpiolib calls, convert + your board or driver to use gpiolib. + Getting the IRQ number associated with a PIN -------------------------------------------- @@ -128,6 +202,9 @@ Getting the IRQ number associated with a PIN Note, not all pins have an IRQ. + This call is now implemented by the relevant gpiolib calls, convert + your board or driver to use gpiolib. + Authour ------- diff --git a/Documentation/arm/Samsung-S3C24XX/Overview.txt b/Documentation/arm/Samsung-S3C24XX/Overview.txt index 081892df4fd..c12bfc1a00c 100644 --- a/Documentation/arm/Samsung-S3C24XX/Overview.txt +++ b/Documentation/arm/Samsung-S3C24XX/Overview.txt @@ -8,10 +8,16 @@ Introduction The Samsung S3C24XX range of ARM9 System-on-Chip CPUs are supported by the 's3c2410' architecture of ARM Linux. Currently the S3C2410, - S3C2412, S3C2413, S3C2440, S3C2442 and S3C2443 devices are supported. + S3C2412, S3C2413, S3C2416 S3C2440, S3C2442, S3C2443 and S3C2450 devices + are supported. Support for the S3C2400 and S3C24A0 series are in progress. + The S3C2416 and S3C2450 devices are very similar and S3C2450 support is + included under the arch/arm/mach-s3c2416 directory. Note, whilst core + support for these SoCs is in, work on some of the extra peripherals + and extra interrupts is still ongoing. + Configuration ------------- @@ -209,6 +215,13 @@ GPIO Newer kernels carry GPIOLIB, and support is being moved towards this with some of the older support in line to be removed. + As of v2.6.34, the move towards using gpiolib support is almost + complete, and very little of the old calls are left. + + See Documentation/arm/Samsung-S3C24XX/GPIO.txt for the S3C24XX specific + support and Documentation/arm/Samsung/GPIO.txt for the core Samsung + implementation. + Clock Management ---------------- diff --git a/Documentation/arm/Samsung/GPIO.txt b/Documentation/arm/Samsung/GPIO.txt new file mode 100644 index 00000000000..05850c62abe --- /dev/null +++ b/Documentation/arm/Samsung/GPIO.txt @@ -0,0 +1,42 @@ + Samsung GPIO implementation + =========================== + +Introduction +------------ + +This outlines the Samsung GPIO implementation and the architecture +specfic calls provided alongisde the drivers/gpio core. + + +S3C24XX (Legacy) +---------------- + +See Documentation/arm/Samsung-S3C24XX/GPIO.txt for more information +about these devices. Their implementation is being brought into line +with the core samsung implementation described in this document. + + +GPIOLIB integration +------------------- + +The gpio implementation uses gpiolib as much as possible, only providing +specific calls for the items that require Samsung specific handling, such +as pin special-function or pull resistor control. + +GPIO numbering is synchronised between the Samsung and gpiolib system. + + +PIN configuration +----------------- + +Pin configuration is specific to the Samsung architecutre, with each SoC +registering the necessary information for the core gpio configuration +implementation to configure pins as necessary. + +The s3c_gpio_cfgpin() and s3c_gpio_setpull() provide the means for a +driver or machine to change gpio configuration. + +See arch/arm/plat-samsung/include/plat/gpio-cfg.h for more information +on these functions. + + diff --git a/Documentation/arm/Samsung/Overview.txt b/Documentation/arm/Samsung/Overview.txt index 7cced1fea9c..c3094ea51aa 100644 --- a/Documentation/arm/Samsung/Overview.txt +++ b/Documentation/arm/Samsung/Overview.txt @@ -13,9 +13,10 @@ Introduction - S3C24XX: See Documentation/arm/Samsung-S3C24XX/Overview.txt for full list - S3C64XX: S3C6400 and S3C6410 - - S5PC6440 - - S5PC100 and S5PC110 support is currently being merged + - S5P6440 + - S5P6442 + - S5PC100 + - S5PC110 / S5PV210 S3C24XX Systems @@ -35,7 +36,10 @@ Configuration unifying all the SoCs into one kernel. s5p6440_defconfig - S5P6440 specific default configuration + s5p6442_defconfig - S5P6442 specific default configuration s5pc100_defconfig - S5PC100 specific default configuration + s5pc110_defconfig - S5PC110 specific default configuration + s5pv210_defconfig - S5PV210 specific default configuration Layout @@ -50,18 +54,27 @@ Layout specific information. It contains the base clock, GPIO and device definitions to get the system running. - plat-s3c is the s3c24xx/s3c64xx platform directory, although it is currently - involved in other builds this will be phased out once the relevant code is - moved elsewhere. - plat-s3c24xx is for s3c24xx specific builds, see the S3C24XX docs. - plat-s3c64xx is for the s3c64xx specific bits, see the S3C24XX docs. + plat-s5p is for s5p specific builds, and contains common support for the + S5P specific systems. Not all S5Ps use all the features in this directory + due to differences in the hardware. + + +Layout changes +-------------- + + The old plat-s3c and plat-s5pc1xx directories have been removed, with + support moved to either plat-samsung or plat-s5p as necessary. These moves + where to simplify the include and dependency issues involved with having + so many different platform directories. - plat-s5p is for s5p specific builds, more to be added. + It was decided to remove plat-s5pc1xx as some of the support was already + in plat-s5p or plat-samsung, with the S5PC110 support added with S5PV210 + the only user was the S5PC100. The S5PC100 specific items where moved to + arch/arm/mach-s5pc100. - [ to finish ] Port Contributors diff --git a/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen b/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen index 1e6a23fdf2f..dc460f05564 100644 --- a/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen +++ b/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen @@ -7,7 +7,7 @@ The driver only implements a four-wire touch panel protocol. The touchscreen driver is maintenance free except for the pen-down or touch threshold. Some resistive displays and board combinations may -require tuning of this threshold. The driver exposes some of it's +require tuning of this threshold. The driver exposes some of its internal state in the sys filesystem. If the kernel is configured with it, CONFIG_SYSFS, and sysfs is mounted at /sys, there will be a directory |