diff options
Diffstat (limited to 'Documentation/devicetree/bindings/clock')
3 files changed, 155 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/clock/calxeda.txt b/Documentation/devicetree/bindings/clock/calxeda.txt new file mode 100644 index 00000000000..0a6ac1bdcda --- /dev/null +++ b/Documentation/devicetree/bindings/clock/calxeda.txt @@ -0,0 +1,17 @@ +Device Tree Clock bindings for Calxeda highbank platform + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "calxeda,hb-pll-clock" - for a PLL clock + "calxeda,hb-a9periph-clock" - The A9 peripheral clock divided from the + A9 clock. + "calxeda,hb-a9bus-clock" - The A9 bus clock divided from the A9 clock. + "calxeda,hb-emmc-clock" - Divided clock for MMC/SD controller. +- reg : shall be the control register offset from SYSREGs base for the clock. +- clocks : shall be the input parent clock phandle for the clock. This is + either an oscillator or a pll output. +- #clock-cells : from common clock binding; shall be set to 0. diff --git a/Documentation/devicetree/bindings/clock/clock-bindings.txt b/Documentation/devicetree/bindings/clock/clock-bindings.txt new file mode 100644 index 00000000000..eb65d417f8c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -0,0 +1,117 @@ +This binding is a work-in-progress, and are based on some experimental +work by benh[1]. + +Sources of clock signal can be represented by any node in the device +tree. Those nodes are designated as clock providers. Clock consumer +nodes use a phandle and clock specifier pair to connect clock provider +outputs to clock inputs. Similar to the gpio specifiers, a clock +specifier is an array of one more more cells identifying the clock +output on a device. The length of a clock specifier is defined by the +value of a #clock-cells property in the clock provider node. + +[1] http://patchwork.ozlabs.org/patch/31551/ + +==Clock providers== + +Required properties: +#clock-cells: Number of cells in a clock specifier; Typically 0 for nodes + with a single clock output and 1 for nodes with multiple + clock outputs. + +Optional properties: +clock-output-names: Recommended to be a list of strings of clock output signal + names indexed by the first cell in the clock specifier. + However, the meaning of clock-output-names is domain + specific to the clock provider, and is only provided to + encourage using the same meaning for the majority of clock + providers. This format may not work for clock providers + using a complex clock specifier format. In those cases it + is recommended to omit this property and create a binding + specific names property. + + Clock consumer nodes must never directly reference + the provider's clock-output-names property. + +For example: + + oscillator { + #clock-cells = <1>; + clock-output-names = "ckil", "ckih"; + }; + +- this node defines a device with two clock outputs, the first named + "ckil" and the second named "ckih". Consumer nodes always reference + clocks by index. The names should reflect the clock output signal + names for the device. + +==Clock consumers== + +Required properties: +clocks: List of phandle and clock specifier pairs, one pair + for each clock input to the device. Note: if the + clock provider specifies '0' for #clock-cells, then + only the phandle portion of the pair will appear. + +Optional properties: +clock-names: List of clock input name strings sorted in the same + order as the clocks property. Consumers drivers + will use clock-names to match clock input names + with clocks specifiers. +clock-ranges: Empty property indicating that child nodes can inherit named + clocks from this node. Useful for bus nodes to provide a + clock to their children. + +For example: + + device { + clocks = <&osc 1>, <&ref 0>; + clock-names = "baud", "register"; + }; + + +This represents a device with two clock inputs, named "baud" and "register". +The baud clock is connected to output 1 of the &osc device, and the register +clock is connected to output 0 of the &ref. + +==Example== + + /* external oscillator */ + osc: oscillator { + compatible = "fixed-clock"; + #clock-cells = <1>; + clock-frequency = <32678>; + clock-output-names = "osc"; + }; + + /* phase-locked-loop device, generates a higher frequency clock + * from the external oscillator reference */ + pll: pll@4c000 { + compatible = "vendor,some-pll-interface" + #clock-cells = <1>; + clocks = <&osc 0>; + clock-names = "ref"; + reg = <0x4c000 0x1000>; + clock-output-names = "pll", "pll-switched"; + }; + + /* UART, using the low frequency oscillator for the baud clock, + * and the high frequency switched PLL output for register + * clocking */ + uart@a000 { + compatible = "fsl,imx-uart"; + reg = <0xa000 0x1000>; + interrupts = <33>; + clocks = <&osc 0>, <&pll 1>; + clock-names = "baud", "register"; + }; + +This DT fragment defines three devices: an external oscillator to provide a +low-frequency reference clock, a PLL device to generate a higher frequency +clock signal, and a UART. + +* The oscillator is fixed-frequency, and provides one clock output, named "osc". +* The PLL is both a clock provider and a clock consumer. It uses the clock + signal generated by the external oscillator, and provides two output signals + ("pll" and "pll-switched"). +* The UART has its baud clock connected the external oscillator and its + register clock connected to the PLL clock (the "pll-switched" signal) diff --git a/Documentation/devicetree/bindings/clock/fixed-clock.txt b/Documentation/devicetree/bindings/clock/fixed-clock.txt new file mode 100644 index 00000000000..0b1fe782409 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/fixed-clock.txt @@ -0,0 +1,21 @@ +Binding for simple fixed-rate clock sources. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "fixed-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- clock-frequency : frequency of clock in Hz. Should be a single cell. + +Optional properties: +- gpios : From common gpio binding; gpio connection to clock enable pin. +- clock-output-names : From common clock binding. + +Example: + clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <1000000000>; + }; |