diff options
Diffstat (limited to 'Documentation/devicetree/bindings/clock')
23 files changed, 609 insertions, 78 deletions
diff --git a/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt b/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt new file mode 100644 index 00000000000..4208886d834 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt @@ -0,0 +1,35 @@ +* Palmas 32KHz clocks * + +Palmas device has two clock output pins for 32KHz, KG and KG_AUDIO. + +This binding uses the common clock binding ./clock-bindings.txt. + +Required properties: +- compatible : "ti,palmas-clk32kg" for clk32kg clock + "ti,palmas-clk32kgaudio" for clk32kgaudio clock +- #clock-cells : shall be set to 0. + +Optional property: +- ti,external-sleep-control: The external enable input pins controlled the + enable/disable of clocks. The external enable input pins ENABLE1, + ENABLE2 and NSLEEP. The valid values for the external pins are: + PALMAS_EXT_CONTROL_PIN_ENABLE1 for ENABLE1 pin + PALMAS_EXT_CONTROL_PIN_ENABLE2 for ENABLE2 pin + PALMAS_EXT_CONTROL_PIN_NSLEEP for NSLEEP pin + Option 0 or missing this property means the clock is enabled/disabled + via register access and these pins do not have any control. + The macros of external control pins for DTS is defined at + dt-bindings/mfd/palmas.h + +Example: + #include <dt-bindings/mfd/palmas.h> + ... + palmas: tps65913@58 { + ... + clk32kg: palmas_clk32k@0 { + compatible = "ti,palmas-clk32kg"; + #clock-cells = <0>; + ti,external-sleep-control = <PALMAS_EXT_CONTROL_PIN_NSLEEP>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/clock/clock-bindings.txt b/Documentation/devicetree/bindings/clock/clock-bindings.txt index f15787817d6..06fc6d541c8 100644 --- a/Documentation/devicetree/bindings/clock/clock-bindings.txt +++ b/Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -131,3 +131,39 @@ clock signal, and a UART. ("pll" and "pll-switched"). * The UART has its baud clock connected the external oscillator and its register clock connected to the PLL clock (the "pll-switched" signal) + +==Assigned clock parents and rates== + +Some platforms may require initial configuration of default parent clocks +and clock frequencies. Such a configuration can be specified in a device tree +node through assigned-clocks, assigned-clock-parents and assigned-clock-rates +properties. The assigned-clock-parents property should contain a list of parent +clocks in form of phandle and clock specifier pairs, the assigned-clock-parents +property the list of assigned clock frequency values - corresponding to clocks +listed in the assigned-clocks property. + +To skip setting parent or rate of a clock its corresponding entry should be +set to 0, or can be omitted if it is not followed by any non-zero entry. + + uart@a000 { + compatible = "fsl,imx-uart"; + reg = <0xa000 0x1000>; + ... + clocks = <&osc 0>, <&pll 1>; + clock-names = "baud", "register"; + + assigned-clocks = <&clkcon 0>, <&pll 2>; + assigned-clock-parents = <&pll 2>; + assigned-clock-rates = <0>, <460800>; + }; + +In this example the <&pll 2> clock is set as parent of clock <&clkcon 0> and +the <&pll 2> clock is assigned a frequency value of 460800 Hz. + +Configuring a clock's parent and rate through the device node that consumes +the clock can be done only for clocks that have a single user. Specifying +conflicting parent or rate configuration in multiple consumer nodes for +a shared clock is forbidden. + +Configuration of common clocks, which affect multiple consumer devices can +be similarly specified in the clock provider node. diff --git a/Documentation/devicetree/bindings/clock/clps711x-clock.txt b/Documentation/devicetree/bindings/clock/clps711x-clock.txt new file mode 100644 index 00000000000..ce5a7476f05 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clps711x-clock.txt @@ -0,0 +1,19 @@ +* Clock bindings for the Cirrus Logic CLPS711X CPUs + +Required properties: +- compatible : Shall contain "cirrus,clps711x-clk". +- reg : Address of the internal register set. +- startup-frequency: Factory set CPU startup frequency in HZ. +- #clock-cells : Should be <1>. + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/clps711x-clock.h +for the full list of CLPS711X clock IDs. + +Example: + clks: clks@80000000 { + #clock-cells = <1>; + compatible = "cirrus,ep7312-clk", "cirrus,clps711x-clk"; + reg = <0x80000000 0xc000>; + startup-frequency = <73728000>; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index 9cfcb4f2bc9..aba3d254e03 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -5,6 +5,8 @@ Required properties : - compatible : shall contain only one of the following: "qcom,gcc-apq8064" + "qcom,gcc-apq8084" + "qcom,gcc-ipq8064" "qcom,gcc-msm8660" "qcom,gcc-msm8960" "qcom,gcc-msm8974" diff --git a/Documentation/devicetree/bindings/clock/qcom,mmcc.txt b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt index d572e9964c5..29ebf84d25a 100644 --- a/Documentation/devicetree/bindings/clock/qcom,mmcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt @@ -4,6 +4,8 @@ Qualcomm Multimedia Clock & Reset Controller Binding Required properties : - compatible : shall contain only one of the following: + "qcom,mmcc-apq8064" + "qcom,mmcc-apq8084" "qcom,mmcc-msm8660" "qcom,mmcc-msm8960" "qcom,mmcc-msm8974" diff --git a/Documentation/devicetree/bindings/clock/corenet-clock.txt b/Documentation/devicetree/bindings/clock/qoriq-clock.txt index 24711af48e3..5666812fc42 100644 --- a/Documentation/devicetree/bindings/clock/corenet-clock.txt +++ b/Documentation/devicetree/bindings/clock/qoriq-clock.txt @@ -7,6 +7,14 @@ which can then be passed to a variety of internal logic, including cores and peripheral IP blocks. Please refer to the Reference Manual for details. +All references to "1.0" and "2.0" refer to the QorIQ chassis version to +which the chip complies. + +Chassis Version Example Chips +--------------- ------------- +1.0 p4080, p5020, p5040 +2.0 t4240, b4860, t1040 + 1. Clock Block Binding Required properties: @@ -85,7 +93,7 @@ Example for clock block and clock provider: #clock-cells = <0>; compatible = "fsl,qoriq-sysclk-1.0"; clock-output-names = "sysclk"; - } + }; pll0: pll0@800 { #clock-cells = <1>; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt new file mode 100644 index 00000000000..0c2bf5eba43 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3188/RK3066 Clock and Reset Unit + +The RK3188/RK3066 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3188-cru", "rockchip,rk3188a-cru" or + "rockchip,rk3066a-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3188-cru.h and +dt-bindings/clock/rk3066-cru.h headers and can be used in device tree sources. +Similar macros exist for the reset sources in these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "xin27m" - 27mhz crystal input on rk3066 - optional, + - "ext_hsadc" - external HSADC clock - optional, + - "ext_cif0" - external camera clock - optional, + - "ext_rmii" - external RMII clock - optional, + - "ext_jtag" - externalJTAG clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3188-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt new file mode 100644 index 00000000000..c9fbb76573e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3288 Clock and Reset Unit + +The RK3288 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3288-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3288-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "ext_i2s" - external I2S clock - optional, + - "ext_hsadc" - external HSADC clock - optional, + - "ext_edp_24m" - external display port clock - optional, + - "ext_vip" - external VIP clock - optional, + - "ext_isp" - external ISP clock - optional, + - "ext_jtag" - external JTAG clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3188-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip.txt b/Documentation/devicetree/bindings/clock/rockchip.txt index a891c823ed4..22f6769e5d4 100644 --- a/Documentation/devicetree/bindings/clock/rockchip.txt +++ b/Documentation/devicetree/bindings/clock/rockchip.txt @@ -6,6 +6,9 @@ This binding uses the common clock binding[1]. == Gate clocks == +These bindings are deprecated! +Please use the soc specific CRU bindings instead. + The gate registers form a continuos block which makes the dt node structure a matter of taste, as either all gates can be put into one gate clock spanning all registers or they can be divided into diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt index ae56315fcec..6247652044a 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt @@ -24,26 +24,26 @@ Required properties: Example: - clockgenA@fd345000 { + clockgen-a@fd345000 { reg = <0xfd345000 0xb50>; - CLK_M_A1_DIV1: CLK_M_A1_DIV1 { + clk_m_a1_div1: clk-m-a1-div1 { #clock-cells = <1>; compatible = "st,clkgena-divmux-c32-odf1", "st,clkgena-divmux"; - clocks = <&CLK_M_A1_OSC_PREDIV>, - <&CLK_M_A1_PLL0 1>, /* PLL0 PHI1 */ - <&CLK_M_A1_PLL1 1>; /* PLL1 PHI1 */ - - clock-output-names = "CLK_M_RX_ICN_TS", - "CLK_M_RX_ICN_VDP_0", - "", /* Unused */ - "CLK_M_PRV_T1_BUS", - "CLK_M_ICN_REG_12", - "CLK_M_ICN_REG_10", - "", /* Unused */ - "CLK_M_ICN_ST231"; + clocks = <&clk_m_a1_osc_prediv>, + <&clk_m_a1_pll0 1>, /* PLL0 PHI1 */ + <&clk_m_a1_pll1 1>; /* PLL1 PHI1 */ + + clock-output-names = "clk-m-rx-icn-ts", + "clk-m-rx-icn-vdp-0", + "", /* unused */ + "clk-m-prv-t1-bus", + "clk-m-icn-reg-12", + "clk-m-icn-reg-10", + "", /* unused */ + "clk-m-icn-st231"; }; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt index 943e0808e21..f1fa91c6876 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt @@ -17,7 +17,7 @@ Required properties: "st,stih416-clkgenf-vcc-sd", "st,clkgen-mux" "st,stih415-clkgen-a9-mux", "st,clkgen-mux" "st,stih416-clkgen-a9-mux", "st,clkgen-mux" - + "st,stih407-clkgen-a9-mux", "st,clkgen-mux" - #clock-cells : from common clock binding; shall be set to 0. @@ -27,10 +27,10 @@ Required properties: Example: - CLK_M_HVA: CLK_M_HVA { + clk_m_hva: clk-m-hva@fd690868 { #clock-cells = <0>; compatible = "st,stih416-clkgenf-vcc-hva", "st,clkgen-mux"; reg = <0xfd690868 4>; - clocks = <&CLOCKGEN_F 1>, <&CLK_M_A1_DIV0 3>; + clocks = <&clockgen_f 1>, <&clk_m_a1_div0 3>; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt index 81eb3855ab9..efb51cf0c84 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt @@ -19,11 +19,14 @@ Required properties: "st,stih415-plls-c32-ddr", "st,clkgen-plls-c32" "st,stih416-plls-c32-a9", "st,clkgen-plls-c32" "st,stih416-plls-c32-ddr", "st,clkgen-plls-c32" + "st,stih407-plls-c32-a0", "st,clkgen-plls-c32" + "st,stih407-plls-c32-a9", "st,clkgen-plls-c32" + "st,stih407-plls-c32-c0_0", "st,clkgen-plls-c32" + "st,stih407-plls-c32-c0_1", "st,clkgen-plls-c32" "st,stih415-gpu-pll-c32", "st,clkgengpu-pll-c32" "st,stih416-gpu-pll-c32", "st,clkgengpu-pll-c32" - - #clock-cells : From common clock binding; shall be set to 1. - clocks : From common clock binding @@ -32,17 +35,17 @@ Required properties: Example: - clockgenA@fee62000 { + clockgen-a@fee62000 { reg = <0xfee62000 0xb48>; - CLK_S_A0_PLL: CLK_S_A0_PLL { + clk_s_a0_pll: clk-s-a0-pll { #clock-cells = <1>; compatible = "st,clkgena-plls-c65"; - clocks = <&CLK_SYSIN>; + clocks = <&clk_sysin>; - clock-output-names = "CLK_S_A0_PLL0_HS", - "CLK_S_A0_PLL0_LS", - "CLK_S_A0_PLL1"; + clock-output-names = "clk-s-a0-pll0-hs", + "clk-s-a0-pll0-ls", + "clk-s-a0-pll1"; }; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt index 566c9d79ed3..604766c2619 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt @@ -20,17 +20,17 @@ Required properties: Example: - clockgenA@fd345000 { + clockgen-a@fd345000 { reg = <0xfd345000 0xb50>; - CLK_M_A2_OSC_PREDIV: CLK_M_A2_OSC_PREDIV { + clk_m_a2_osc_prediv: clk-m-a2-osc-prediv { #clock-cells = <0>; compatible = "st,clkgena-prediv-c32", "st,clkgena-prediv"; - clocks = <&CLK_SYSIN>; + clocks = <&clk_sysin>; - clock-output-names = "CLK_M_A2_OSC_PREDIV"; + clock-output-names = "clk-m-a2-osc-prediv"; }; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt index 4e3ff28b04c..109b3eddcb1 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt @@ -32,22 +32,30 @@ Required properties: Example: - CLOCKGEN_C_VCC: CLOCKGEN_C_VCC { + clockgen_c_vcc: clockgen-c-vcc@0xfe8308ac { #clock-cells = <1>; compatible = "st,stih416-clkgenc", "st,clkgen-vcc"; reg = <0xfe8308ac 12>; - clocks = <&CLK_S_VCC_HD>, <&CLOCKGEN_C 1>, - <&CLK_S_TMDS_FROMPHY>, <&CLOCKGEN_C 2>; - - clock-output-names = - "CLK_S_PIX_HDMI", "CLK_S_PIX_DVO", - "CLK_S_OUT_DVO", "CLK_S_PIX_HD", - "CLK_S_HDDAC", "CLK_S_DENC", - "CLK_S_SDDAC", "CLK_S_PIX_MAIN", - "CLK_S_PIX_AUX", "CLK_S_STFE_FRC_0", - "CLK_S_REF_MCRU", "CLK_S_SLAVE_MCRU", - "CLK_S_TMDS_HDMI", "CLK_S_HDMI_REJECT_PLL", - "CLK_S_THSENS"; + clocks = <&clk_s_vcc_hd>, + <&clockgen_c 1>, + <&clk_s_tmds_fromphy>, + <&clockgen_c 2>; + + clock-output-names = "clk-s-pix-hdmi", + "clk-s-pix-dvo", + "clk-s-out-dvo", + "clk-s-pix-hd", + "clk-s-hddac", + "clk-s-denc", + "clk-s-sddac", + "clk-s-pix-main", + "clk-s-pix-aux", + "clk-s-stfe-frc-0", + "clk-s-ref-mcru", + "clk-s-slave-mcru", + "clk-s-tmds-hdmi", + "clk-s-hdmi-reject-pll", + "clk-s-thsens"; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt index 49ec5ae18b5..78978f1f515 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt @@ -24,60 +24,77 @@ address is common of all subnode. quadfs_node { ... }; + + mux_node { + ... + }; + + vcc_node { + ... + }; + + flexgen_node { + ... + }; ... }; This binding uses the common clock binding[1]. -Each subnode should use the binding discribe in [2]..[4] +Each subnode should use the binding discribe in [2]..[7] [1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/clock/st,quadfs.txt -[3] Documentation/devicetree/bindings/clock/st,quadfs.txt -[4] Documentation/devicetree/bindings/clock/st,quadfs.txt +[2] Documentation/devicetree/bindings/clock/st,clkgen-divmux.txt +[3] Documentation/devicetree/bindings/clock/st,clkgen-mux.txt +[4] Documentation/devicetree/bindings/clock/st,clkgen-pll.txt +[5] Documentation/devicetree/bindings/clock/st,clkgen-prediv.txt +[6] Documentation/devicetree/bindings/clock/st,vcc.txt +[7] Documentation/devicetree/bindings/clock/st,quadfs.txt +[8] Documentation/devicetree/bindings/clock/st,flexgen.txt + Required properties: - reg : A Base address and length of the register set. Example: - clockgenA@fee62000 { + clockgen-a@fee62000 { reg = <0xfee62000 0xb48>; - CLK_S_A0_PLL: CLK_S_A0_PLL { + clk_s_a0_pll: clk-s-a0-pll { #clock-cells = <1>; compatible = "st,clkgena-plls-c65"; - clocks = <&CLK_SYSIN>; + clocks = <&clk-sysin>; - clock-output-names = "CLK_S_A0_PLL0_HS", - "CLK_S_A0_PLL0_LS", - "CLK_S_A0_PLL1"; + clock-output-names = "clk-s-a0-pll0-hs", + "clk-s-a0-pll0-ls", + "clk-s-a0-pll1"; }; - CLK_S_A0_OSC_PREDIV: CLK_S_A0_OSC_PREDIV { + clk_s_a0_osc_prediv: clk-s-a0-osc-prediv { #clock-cells = <0>; compatible = "st,clkgena-prediv-c65", "st,clkgena-prediv"; - clocks = <&CLK_SYSIN>; + clocks = <&clk_sysin>; - clock-output-names = "CLK_S_A0_OSC_PREDIV"; + clock-output-names = "clk-s-a0-osc-prediv"; }; - CLK_S_A0_HS: CLK_S_A0_HS { + clk_s_a0_hs: clk-s-a0-hs { #clock-cells = <1>; compatible = "st,clkgena-divmux-c65-hs", "st,clkgena-divmux"; - clocks = <&CLK_S_A0_OSC_PREDIV>, - <&CLK_S_A0_PLL 0>, /* PLL0 HS */ - <&CLK_S_A0_PLL 2>; /* PLL1 */ + clocks = <&clk-s_a0_osc_prediv>, + <&clk-s_a0_pll 0>, /* pll0 hs */ + <&clk-s_a0_pll 2>; /* pll1 */ - clock-output-names = "CLK_S_FDMA_0", - "CLK_S_FDMA_1", - ""; /* CLK_S_JIT_SENSE */ - /* Fourth output unused */ + clock-output-names = "clk-s-fdma-0", + "clk-s-fdma-1", + ""; /* clk-s-jit-sense */ + /* fourth output unused */ }; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,flexgen.txt b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt new file mode 100644 index 00000000000..1d3ace08817 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt @@ -0,0 +1,119 @@ +Binding for a type of flexgen structure found on certain +STMicroelectronics consumer electronics SoC devices + +This structure includes: +- a clock cross bar (represented by a mux element) +- a pre and final dividers (represented by a divider and gate elements) + +Flexgen structure is a part of Clockgen[1]. + +Please find an example below: + + Clockgen block diagram + ------------------------------------------------------------------- + | Flexgen stucture | + | --------------------------------------------- | + | | ------- -------- -------- | | +clk_sysin | | | | | | | | | +---|-----------------|-->| | | | | | | | + | | | | | | | | | | | + | | ------- | | | |Pre | |Final | | | + | | |PLL0 | | | | |Dividers| |Dividers| | | + | |->| | | | | | x32 | | x32 | | | + | | | odf_0|----|-->| | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | ------- | | | | | | | | | + | | | | | | | | | | | + | | ------- | | Clock | | | | | | | + | | |PLL1 | | | | | | | | | | + | |->| | | | Cross | | | | | | | + | | | odf_0|----|-->| | | | | | CLK_DIV[31:0] + | | | | | | Bar |====>| |====>| |===|=========> + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | ------- | | | | | | | | | + | | | | | | | | | | | + | | ------- | | | | | | | | | + | | |QUADFS | | | | | | | | | | + | |->| ch0|----|-->| | | | | | | | + | | | | | | | | | | | | + | | ch1|----|-->| | | | | | | | + | | | | | | | | | | | | + | | ch2|----|-->| | | DIV | | DIV | | | + | | | | | | | 1 to | | 1 to | | | + | | ch3|----|-->| | | 1024 | | 64 | | | + | ------- | | | | | | | | | + | | ------- -------- -------- | | + | -------------------------------------------- | + | | + ------------------------------------------------------------------- + +This binding uses the common clock binding[2]. + +[1] Documentation/devicetree/bindings/clock/st/st,clkgen.txt +[2] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be: + "st,flexgen" + +- #clock-cells : from common clock binding; shall be set to 1 (multiple clock + outputs). + +- clocks : must be set to the parent's phandle. it's could be output clocks of + a quadsfs or/and a pll or/and clk_sysin (up to 7 clocks) + +- clock-output-names : List of strings used to name the clock outputs. + +Example: + + clk_s_c0_flexgen: clk-s-c0-flexgen { + + #clock-cells = <1>; + compatible = "st,flexgen"; + + clocks = <&clk_s_c0_pll0 0>, + <&clk_s_c0_pll1 0>, + <&clk_s_c0_quadfs 0>, + <&clk_s_c0_quadfs 1>, + <&clk_s_c0_quadfs 2>, + <&clk_s_c0_quadfs 3>, + <&clk_sysin>; + + clock-output-names = "clk-icn-gpu", + "clk-fdma", + "clk-nand", + "clk-hva", + "clk-proc-stfe", + "clk-proc-tp", + "clk-rx-icn-dmu", + "clk-rx-icn-hva", + "clk-icn-cpu", + "clk-tx-icn-dmu", + "clk-mmc-0", + "clk-mmc-1", + "clk-jpegdec", + "clk-ext2fa9", + "clk-ic-bdisp-0", + "clk-ic-bdisp-1", + "clk-pp-dmu", + "clk-vid-dmu", + "clk-dss-lpc", + "clk-st231-aud-0", + "clk-st231-gp-1", + "clk-st231-dmu", + "clk-icn-lmi", + "clk-tx-icn-disp-1", + "clk-icn-sbc", + "clk-stfe-frc2", + "clk-eth-phy", + "clk-eth-ref-phyclk", + "clk-flash-promip", + "clk-main-disp", + "clk-aux-disp", + "clk-compo-dvp"; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,quadfs.txt b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt index ec86d62ca28..cedeb9cc820 100644 --- a/Documentation/devicetree/bindings/clock/st/st,quadfs.txt +++ b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt @@ -15,6 +15,9 @@ Required properties: "st,stih416-quadfs432", "st,quadfs" "st,stih416-quadfs660-E", "st,quadfs" "st,stih416-quadfs660-F", "st,quadfs" + "st,stih407-quadfs660-C", "st,quadfs" + "st,stih407-quadfs660-D", "st,quadfs" + - #clock-cells : from common clock binding; shall be set to 1. @@ -32,14 +35,14 @@ Required properties: Example: - CLOCKGEN_E: CLOCKGEN_E { + clockgen_e: clockgen-e@fd3208bc { #clock-cells = <1>; compatible = "st,stih416-quadfs660-E", "st,quadfs"; reg = <0xfd3208bc 0xB0>; - clocks = <&CLK_SYSIN>; - clock-output-names = "CLK_M_PIX_MDTP_0", - "CLK_M_PIX_MDTP_1", - "CLK_M_PIX_MDTP_2", - "CLK_M_MPELPC"; + clocks = <&clk_sysin>; + clock-output-names = "clk-m-pix-mdtp-0", + "clk-m-pix-mdtp-1", + "clk-m-pix-mdtp-2", + "clk-m-mpelpc"; }; diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index a5160d8cbb5..d3a5c3c6d67 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -9,24 +9,32 @@ Required properties: "allwinner,sun4i-a10-osc-clk" - for a gatable oscillator "allwinner,sun4i-a10-pll1-clk" - for the main PLL clock and PLL4 "allwinner,sun6i-a31-pll1-clk" - for the main PLL clock on A31 + "allwinner,sun8i-a23-pll1-clk" - for the main PLL clock on A23 "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31 "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock "allwinner,sun4i-a10-axi-clk" - for the AXI clock + "allwinner,sun8i-a23-axi-clk" - for the AXI clock on A23 "allwinner,sun4i-a10-axi-gates-clk" - for the AXI gates "allwinner,sun4i-a10-ahb-clk" - for the AHB clock "allwinner,sun4i-a10-ahb-gates-clk" - for the AHB gates on A10 "allwinner,sun5i-a13-ahb-gates-clk" - for the AHB gates on A13 "allwinner,sun5i-a10s-ahb-gates-clk" - for the AHB gates on A10s "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20 + "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31 "allwinner,sun6i-a31-ahb1-mux-clk" - for the AHB1 multiplexer on A31 "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31 + "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23 "allwinner,sun4i-a10-apb0-clk" - for the APB0 clock + "allwinner,sun6i-a31-apb0-clk" - for the APB0 clock on A31 + "allwinner,sun8i-a23-apb0-clk" - for the APB0 clock on A23 "allwinner,sun4i-a10-apb0-gates-clk" - for the APB0 gates on A10 "allwinner,sun5i-a13-apb0-gates-clk" - for the APB0 gates on A13 "allwinner,sun5i-a10s-apb0-gates-clk" - for the APB0 gates on A10s + "allwinner,sun6i-a31-apb0-gates-clk" - for the APB0 gates on A31 "allwinner,sun7i-a20-apb0-gates-clk" - for the APB0 gates on A20 + "allwinner,sun8i-a23-apb0-gates-clk" - for the APB0 gates on A23 "allwinner,sun4i-a10-apb1-clk" - for the APB1 clock "allwinner,sun4i-a10-apb1-mux-clk" - for the APB1 clock muxing "allwinner,sun4i-a10-apb1-gates-clk" - for the APB1 gates on A10 @@ -34,13 +42,16 @@ Required properties: "allwinner,sun5i-a10s-apb1-gates-clk" - for the APB1 gates on A10s "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31 "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20 + "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23 "allwinner,sun6i-a31-apb2-div-clk" - for the APB2 gates on A31 "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31 + "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23 "allwinner,sun4i-a10-mod0-clk" - for the module 0 family of clocks "allwinner,sun7i-a20-out-clk" - for the external output clocks "allwinner,sun7i-a20-gmac-clk" - for the GMAC clock module on A20/A31 "allwinner,sun4i-a10-usb-clk" - for usb gates + resets on A10 / A20 "allwinner,sun5i-a13-usb-clk" - for usb gates + resets on A13 + "allwinner,sun6i-a31-usb-clk" - for usb gates + resets on A31 Required properties for all clocks: - reg : shall be the control register address for the clock. diff --git a/Documentation/devicetree/bindings/clock/ti/apll.txt b/Documentation/devicetree/bindings/clock/ti/apll.txt index 7faf5a68b3b..ade4dd4c30f 100644 --- a/Documentation/devicetree/bindings/clock/ti/apll.txt +++ b/Documentation/devicetree/bindings/clock/ti/apll.txt @@ -14,18 +14,32 @@ a subtype of a DPLL [2], although a simplified one at that. [2] Documentation/devicetree/bindings/clock/ti/dpll.txt Required properties: -- compatible : shall be "ti,dra7-apll-clock" +- compatible : shall be "ti,dra7-apll-clock" or "ti,omap2-apll-clock" - #clock-cells : from common clock binding; shall be set to 0. - clocks : link phandles of parent clocks (clk-ref and clk-bypass) - reg : address and length of the register set for controlling the APLL. It contains the information of registers in the following order: - "control" - contains the control register base address - "idlest" - contains the idlest register base address + "control" - contains the control register offset + "idlest" - contains the idlest register offset + "autoidle" - contains the autoidle register offset (OMAP2 only) +- ti,clock-frequency : static clock frequency for the clock (OMAP2 only) +- ti,idlest-shift : bit-shift for the idlest field (OMAP2 only) +- ti,bit-shift : bit-shift for enable and autoidle fields (OMAP2 only) Examples: - apll_pcie_ck: apll_pcie_ck@4a008200 { + apll_pcie_ck: apll_pcie_ck { #clock-cells = <0>; clocks = <&apll_pcie_in_clk_mux>, <&dpll_pcie_ref_ck>; - reg = <0x4a00821c 0x4>, <0x4a008220 0x4>; + reg = <0x021c>, <0x0220>; compatible = "ti,dra7-apll-clock"; }; + + apll96_ck: apll96_ck { + #clock-cells = <0>; + compatible = "ti,omap2-apll-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <2>; + ti,idlest-shift = <8>; + ti,clock-frequency = <96000000>; + reg = <0x0500>, <0x0530>, <0x0520>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/dpll.txt b/Documentation/devicetree/bindings/clock/ti/dpll.txt index 30bfdb7c9f1..df57009ff8e 100644 --- a/Documentation/devicetree/bindings/clock/ti/dpll.txt +++ b/Documentation/devicetree/bindings/clock/ti/dpll.txt @@ -24,12 +24,14 @@ Required properties: "ti,omap4-dpll-core-clock", "ti,omap4-dpll-m4xen-clock", "ti,omap4-dpll-j-type-clock", + "ti,omap5-mpu-dpll-clock", "ti,am3-dpll-no-gate-clock", "ti,am3-dpll-j-type-clock", "ti,am3-dpll-no-gate-j-type-clock", "ti,am3-dpll-clock", "ti,am3-dpll-core-clock", "ti,am3-dpll-x2-clock", + "ti,omap2-dpll-core-clock", - #clock-cells : from common clock binding; shall be set to 0. - clocks : link phandles of parent clocks, first entry lists reference clock @@ -41,6 +43,7 @@ Required properties: "mult-div1" - contains the multiplier / divider register base address "autoidle" - contains the autoidle register base address (optional) ti,am3-* dpll types do not have autoidle register + ti,omap2-* dpll type does not support idlest / autoidle registers Optional properties: - DPLL mode setting - defining any one or more of the following overrides @@ -73,3 +76,10 @@ Examples: clocks = <&sys_clkin_ck>, <&sys_clkin_ck>; reg = <0x90>, <0x5c>, <0x68>; }; + + dpll_ck: dpll_ck { + #clock-cells = <0>; + compatible = "ti,omap2-dpll-core-clock"; + clocks = <&sys_ck>, <&sys_ck>; + reg = <0x0500>, <0x0540>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt b/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt new file mode 100644 index 00000000000..585e8c191f5 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt @@ -0,0 +1,96 @@ +Device Tree Clock bindings for ATL (Audio Tracking Logic) of DRA7 SoC. + +The ATL IP is used to generate clock to be used to synchronize baseband and +audio codec. A single ATL IP provides four ATL clock instances sharing the same +functional clock but can be configured to provide different clocks. +ATL can maintain a clock averages to some desired frequency based on the bws/aws +signals - can compensate the drift between the two ws signal. + +In order to provide the support for ATL and it's output clocks (which can be used +internally within the SoC or external components) two sets of bindings is needed: + +Clock tree binding: +This binding uses the common clock binding[1]. +To be able to integrate the ATL clocks with DT clock tree. +Provides ccf level representation of the ATL clocks to be used by drivers. +Since the clock instances are part of a single IP this binding is used as a node +for the DT clock tree, the IP driver is needed to handle the actual configuration +of the IP. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "ti,dra7-atl-clock" +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles to functional clock of ATL + +Binding for the IP driver: +This binding is used to configure the IP driver which is going to handle the +configuration of the IP for the ATL clock instances. + +Required properties: +- compatible : shall be "ti,dra7-atl" +- reg : base address for the ATL IP +- ti,provided-clocks : List of phandles to the clocks associated with the ATL +- clocks : link phandles to functional clock of ATL +- clock-names : Shall be set to "fck" +- ti,hwmods : Shall be set to "atl" + +Optional properties: +Configuration of ATL instances: +- atl{0/1/2/3} { + - bws : Baseband word select signal selection + - aws : Audio word select signal selection +}; + +For valid word select signals, see the dt-bindings/clk/ti-dra7-atl.h include +file. + +Examples: +/* clock bindings for atl provided clocks */ +atl_clkin0_ck: atl_clkin0_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +atl_clkin1_ck: atl_clkin1_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +atl_clkin2_ck: atl_clkin2_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +atl_clkin3_ck: atl_clkin3_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +/* binding for the IP */ +atl: atl@4843c000 { + compatible = "ti,dra7-atl"; + reg = <0x4843c000 0x3ff>; + ti,hwmods = "atl"; + ti,provided-clocks = <&atl_clkin0_ck>, <&atl_clkin1_ck>, + <&atl_clkin2_ck>, <&atl_clkin3_ck>; + clocks = <&atl_gfclk_mux>; + clock-names = "fck"; + status = "disabled"; +}; + +#include <dt-bindings/clk/ti-dra7-atl.h> + +&atl { + status = "okay"; + + atl2 { + bws = <DRA7_ATL_WS_MCASP2_FSX>; + aws = <DRA7_ATL_WS_MCASP3_FSX>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/ti/gate.txt b/Documentation/devicetree/bindings/clock/ti/gate.txt index 125281aaa4c..03f8fdee62a 100644 --- a/Documentation/devicetree/bindings/clock/ti/gate.txt +++ b/Documentation/devicetree/bindings/clock/ti/gate.txt @@ -25,6 +25,11 @@ Required properties: to map clockdomains properly "ti,hsdiv-gate-clock" - gate clock with OMAP36xx specific hardware handling, required for a hardware errata + "ti,composite-gate-clock" - composite gate clock, to be part of composite + clock + "ti,composite-no-wait-gate-clock" - composite gate clock that does not wait + for clock to be active before returning + from clk_enable() - #clock-cells : from common clock binding; shall be set to 0 - clocks : link to phandle of parent clock - reg : offset for register controlling adjustable gate, not needed for @@ -41,7 +46,7 @@ Examples: #clock-cells = <0>; compatible = "ti,gate-clock"; clocks = <&core_96m_fck>; - reg = <0x48004a00 0x4>; + reg = <0x0a00>; ti,bit-shift = <25>; }; @@ -57,7 +62,7 @@ Examples: #clock-cells = <0>; compatible = "ti,dss-gate-clock"; clocks = <&dpll4_m4x2_ck>; - reg = <0x48004e00 0x4>; + reg = <0x0e00>; ti,bit-shift = <0>; }; @@ -65,7 +70,7 @@ Examples: #clock-cells = <0>; compatible = "ti,am35xx-gate-clock"; clocks = <&ipss_ick>; - reg = <0x4800259c 0x4>; + reg = <0x059c>; ti,bit-shift = <1>; }; @@ -80,6 +85,22 @@ Examples: compatible = "ti,hsdiv-gate-clock"; clocks = <&dpll4_m2x2_mul_ck>; ti,bit-shift = <0x1b>; - reg = <0x48004d00 0x4>; + reg = <0x0d00>; ti,set-bit-to-disable; }; + + vlynq_gate_fck: vlynq_gate_fck { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&core_ck>; + ti,bit-shift = <3>; + reg = <0x0200>; + }; + + sys_clkout2_src_gate: sys_clkout2_src_gate { + #clock-cells = <0>; + compatible = "ti,composite-no-wait-gate-clock"; + clocks = <&core_ck>; + ti,bit-shift = <15>; + reg = <0x0070>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/interface.txt b/Documentation/devicetree/bindings/clock/ti/interface.txt index 064e8caccac..3111a409fea 100644 --- a/Documentation/devicetree/bindings/clock/ti/interface.txt +++ b/Documentation/devicetree/bindings/clock/ti/interface.txt @@ -21,6 +21,8 @@ Required properties: "ti,omap3-dss-interface-clock" - interface clock with DSS specific HW handling "ti,omap3-ssi-interface-clock" - interface clock with SSI specific HW handling "ti,am35xx-interface-clock" - interface clock with AM35xx specific HW handling + "ti,omap2430-interface-clock" - interface clock with OMAP2430 specific HW + handling - #clock-cells : from common clock binding; shall be set to 0 - clocks : link to phandle of parent clock - reg : base address for the control register |