diff options
Diffstat (limited to 'Documentation/devicetree/bindings/gpio/8xxx_gpio.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/gpio/8xxx_gpio.txt | 66 |
1 files changed, 40 insertions, 26 deletions
diff --git a/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt b/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt index b0019eb5330..798cfc9d383 100644 --- a/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt +++ b/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt @@ -5,16 +5,42 @@ This is for the non-QE/CPM/GUTs GPIO controllers as found on Every GPIO controller node must have #gpio-cells property defined, this information will be used to translate gpio-specifiers. +See bindings/gpio/gpio.txt for details of how to specify GPIO +information for devices. + +The GPIO module usually is connected to the SoC's internal interrupt +controller, see bindings/interrupt-controller/interrupts.txt (the +interrupt client nodes section) for details how to specify this GPIO +module's interrupt. + +The GPIO module may serve as another interrupt controller (cascaded to +the SoC's internal interrupt controller). See the interrupt controller +nodes section in bindings/interrupt-controller/interrupts.txt for +details. Required properties: -- compatible : "fsl,<CHIP>-gpio" followed by "fsl,mpc8349-gpio" for - 83xx, "fsl,mpc8572-gpio" for 85xx and "fsl,mpc8610-gpio" for 86xx. -- #gpio-cells : Should be two. The first cell is the pin number and the - second cell is used to specify optional parameters (currently unused). - - interrupts : Interrupt mapping for GPIO IRQ. - - interrupt-parent : Phandle for the interrupt controller that - services interrupts for this device. -- gpio-controller : Marks the port as GPIO controller. +- compatible: "fsl,<chip>-gpio" followed by "fsl,mpc8349-gpio" + for 83xx, "fsl,mpc8572-gpio" for 85xx, or + "fsl,mpc8610-gpio" for 86xx. +- #gpio-cells: Should be two. The first cell is the pin number + and the second cell is used to specify optional + parameters (currently unused). +- interrupt-parent: Phandle for the interrupt controller that + services interrupts for this device. +- interrupts: Interrupt mapping for GPIO IRQ. +- gpio-controller: Marks the port as GPIO controller. + +Optional properties: +- interrupt-controller: Empty boolean property which marks the GPIO + module as an IRQ controller. +- #interrupt-cells: Should be two. Defines the number of integer + cells required to specify an interrupt within + this interrupt controller. The first cell + defines the pin number, the second cell + defines additional flags (trigger type, + trigger polarity). Note that the available + set of trigger conditions supported by the + GPIO module depends on the actual SoC. Example of gpio-controller nodes for a MPC8347 SoC: @@ -22,39 +48,27 @@ Example of gpio-controller nodes for a MPC8347 SoC: #gpio-cells = <2>; compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; reg = <0xc00 0x100>; - interrupts = <74 0x8>; interrupt-parent = <&ipic>; + interrupts = <74 0x8>; gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; }; gpio2: gpio-controller@d00 { #gpio-cells = <2>; compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; reg = <0xd00 0x100>; - interrupts = <75 0x8>; interrupt-parent = <&ipic>; + interrupts = <75 0x8>; gpio-controller; }; -See booting-without-of.txt for details of how to specify GPIO -information for devices. - -To use GPIO pins as interrupt sources for peripherals, specify the -GPIO controller as the interrupt parent and define GPIO number + -trigger mode using the interrupts property, which is defined like -this: - -interrupts = <number trigger>, where: - - number: GPIO pin (0..31) - - trigger: trigger mode: - 2 = trigger on falling edge - 3 = trigger on both edges - -Example of device using this is: +Example of a peripheral using the GPIO module as an IRQ controller: funkyfpga@0 { compatible = "funky-fpga"; ... - interrupts = <4 3>; interrupt-parent = <&gpio1>; + interrupts = <4 3>; }; |