diff options
Diffstat (limited to 'Documentation/devicetree/bindings/gpio')
4 files changed, 197 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt b/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt new file mode 100644 index 00000000000..00611aceed3 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt @@ -0,0 +1,36 @@ +* Abilis TB10x GPIO controller + +Required Properties: +- compatible: Should be "abilis,tb10x-gpio" +- reg: Address and length of the register set for the device +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be <2>. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted). +- abilis,ngpio: the number of GPIO pins this driver controls. + +Optional Properties: +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be <1>. Interrupts are triggered on both edges. +- interrupts: Defines the interrupt line connecting this GPIO controller to + its parent interrupt controller. +- interrupt-parent: Defines the parent interrupt controller. + +GPIO ranges are specified as described in +Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + + gpioa: gpio@FF140000 { + compatible = "abilis,tb10x-gpio"; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&tb10x_ictl>; + interrupts = <27 2>; + reg = <0xFF140000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + abilis,ngpio = <3>; + gpio-ranges = <&iomux 0 0 0>; + gpio-ranges-group-names = "gpioa_pins"; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-bcm-kona.txt b/Documentation/devicetree/bindings/gpio/gpio-bcm-kona.txt new file mode 100644 index 00000000000..4a63bc96b68 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-bcm-kona.txt @@ -0,0 +1,52 @@ +Broadcom Kona Family GPIO +========================= + +This GPIO driver is used in the following Broadcom SoCs: + BCM11130, BCM11140, BCM11351, BCM28145, BCM28155 + +The Broadcom GPIO Controller IP can be configured prior to synthesis to +support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The +GPIO controller only supports edge, not level, triggering of interrupts. + +Required properties +------------------- + +- compatible: "brcm,bcm11351-gpio", "brcm,kona-gpio" +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt outputs from the controller. There is one GPIO + interrupt per GPIO bank. The number of interrupts listed depends on the + number of GPIO banks on the SoC. The interrupts must be ordered by bank, + starting with bank 0. There is always a 1:1 mapping between banks and + IRQs. +- #gpio-cells: Should be <2>. The first cell is the pin number, the second + cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) + See also "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. +- #interrupt-cells: Should be <2>. The first cell is the GPIO number. The + second cell is used to specify flags. The following subset of flags is + supported: + - trigger type (bits[1:0]): + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 3 = low-to-high or high-to-low edge triggered + Valid values are 1, 2, 3 + See also .../devicetree/bindings/interrupt-controller/interrupts.txt. +- gpio-controller: Marks the device node as a GPIO controller. +- interrupt-controller: Marks the device node as an interrupt controller. + +Example: + gpio: gpio@35003000 { + compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio"; + reg = <0x35003000 0x800>; + interrupts = + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + #interrupt-cells = <2>; + gpio-controller; + interrupt-controller; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt b/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt new file mode 100644 index 00000000000..d63194a2c84 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt @@ -0,0 +1,71 @@ +* PCF857x-compatible I/O expanders + +The PCF857x-compatible chips have "quasi-bidirectional" I/O lines that can be +driven high by a pull-up current source or driven low to ground. This combines +the direction and output level into a single bit per line, which can't be read +back. We can't actually know at initialization time whether a line is configured +(a) as output and driving the signal low/high, or (b) as input and reporting a +low/high value, without knowing the last value written since the chip came out +of reset (if any). The only reliable solution for setting up line direction is +thus to do it explicitly. + +Required Properties: + + - compatible: should be one of the following. + - "maxim,max7328": For the Maxim MAX7378 + - "maxim,max7329": For the Maxim MAX7329 + - "nxp,pca8574": For the NXP PCA8574 + - "nxp,pca8575": For the NXP PCA8575 + - "nxp,pca9670": For the NXP PCA9670 + - "nxp,pca9671": For the NXP PCA9671 + - "nxp,pca9672": For the NXP PCA9672 + - "nxp,pca9673": For the NXP PCA9673 + - "nxp,pca9674": For the NXP PCA9674 + - "nxp,pca9675": For the NXP PCA9675 + - "nxp,pcf8574": For the NXP PCF8574 + - "nxp,pcf8574a": For the NXP PCF8574A + - "nxp,pcf8575": For the NXP PCF8575 + - "ti,tca9554": For the TI TCA9554 + + - reg: I2C slave address. + + - gpio-controller: Marks the device node as a gpio controller. + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the + GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. + +Optional Properties: + + - lines-initial-states: Bitmask that specifies the initial state of each + line. When a bit is set to zero, the corresponding line will be initialized to + the input (pulled-up) state. When the bit is set to one, the line will be + initialized the the low-level output state. If the property is not specified + all lines will be initialized to the input state. + + The I/O expander can detect input state changes, and thus optionally act as + an interrupt controller. When the expander interrupt line is connected all the + following properties must be set. For more information please see the + interrupt controller device tree bindings documentation available at + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt. + + - interrupt-controller: Identifies the node as an interrupt controller. + - #interrupt-cells: Number of cells to encode an interrupt source, shall be 2. + - interrupt-parent: phandle of the parent interrupt controller. + - interrupts: Interrupt specifier for the controllers interrupt. + + +Please refer to gpio.txt in this directory for details of the common GPIO +bindings used by client devices. + +Example: PCF8575 I/O expander node + + pcf8575: gpio@20 { + compatible = "nxp,pcf8575"; + reg = <0x20>; + interrupt-parent = <&irqpin2>; + interrupts = <3 0>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 6cec6ff20d2..0c85bb6e3a8 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -87,8 +87,10 @@ controllers. The gpio-ranges property described below represents this, and contains information structures as follows: gpio-range-list ::= <single-gpio-range> [gpio-range-list] - single-gpio-range ::= + single-gpio-range ::= <numeric-gpio-range> | <named-gpio-range> + numeric-gpio-range ::= <pinctrl-phandle> <gpio-base> <pinctrl-base> <count> + named-gpio-range ::= <pinctrl-phandle> <gpio-base> '<0 0>' gpio-phandle : phandle to pin controller node. gpio-base : Base GPIO ID in the GPIO controller pinctrl-base : Base pinctrl pin ID in the pin controller @@ -97,6 +99,19 @@ contains information structures as follows: The "pin controller node" mentioned above must conform to the bindings described in ../pinctrl/pinctrl-bindings.txt. +In case named gpio ranges are used (ranges with both <pinctrl-base> and +<count> set to 0), the property gpio-ranges-group-names contains one string +for every single-gpio-range in gpio-ranges: + gpiorange-names-list ::= <gpiorange-name> [gpiorange-names-list] + gpiorange-name : Name of the pingroup associated to the GPIO range in + the respective pin controller. + +Elements of gpiorange-names-list corresponding to numeric ranges contain +the empty string. Elements of gpiorange-names-list corresponding to named +ranges contain the name of a pin group defined in the respective pin +controller. The number of pins/GPIOs in the range is the number of pins in +that pin group. + Previous versions of this binding required all pin controller nodes that were referenced by any gpio-ranges property to contain a property named #gpio-range-cells with value <3>. This requirement is now deprecated. @@ -104,7 +119,7 @@ However, that property may still exist in older device trees for compatibility reasons, and would still be required even in new device trees that need to be compatible with older software. -Example: +Example 1: qe_pio_e: gpio-controller@1460 { #gpio-cells = <2>; @@ -117,3 +132,24 @@ Example: Here, a single GPIO controller has GPIOs 0..9 routed to pin controller pinctrl1's pins 20..29, and GPIOs 10..19 routed to pin controller pinctrl2's pins 50..59. + +Example 2: + + gpio_pio_i: gpio-controller@14B0 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1480 0x18>; + gpio-controller; + gpio-ranges = <&pinctrl1 0 20 10>, + <&pinctrl2 10 0 0>, + <&pinctrl1 15 0 10>, + <&pinctrl2 25 0 0>; + gpio-ranges-group-names = "", + "foo", + "", + "bar"; + }; + +Here, three GPIO ranges are defined wrt. two pin controllers. pinctrl1 GPIO +ranges are defined using pin numbers whereas the GPIO ranges wrt. pinctrl2 +are named "foo" and "bar". |