diff options
Diffstat (limited to 'Documentation/devicetree/bindings/gpio')
8 files changed, 208 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-74x164.txt b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt new file mode 100644 index 00000000000..cc2608021f2 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt @@ -0,0 +1,22 @@ +* Generic 8-bits shift register GPIO driver + +Required properties: +- compatible : Should be "fairchild,74hc595" +- reg : chip select number +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- registers-number: Number of daisy-chained shift registers + +Example: + +gpio5: gpio5@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <4>; + spi-max-frequency = <100000>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-adnp.txt b/Documentation/devicetree/bindings/gpio/gpio-adnp.txt new file mode 100644 index 00000000000..af66b272483 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-adnp.txt @@ -0,0 +1,34 @@ +Avionic Design N-bit GPIO expander bindings + +Required properties: +- compatible: should be "ad,gpio-adnp" +- reg: The I2C slave address for this device. +- interrupt-parent: phandle of the parent interrupt controller. +- interrupts: Interrupt specifier for the controllers interrupt. +- #gpio-cells: Should be 2. The first cell is the GPIO number and the + second cell is used to specify optional parameters: + - bit 0: polarity (0: normal, 1: inverted) +- gpio-controller: Marks the device as a GPIO controller +- nr-gpios: The number of pins supported by the controller. + +The GPIO expander can optionally be used as an interrupt controller, in +which case it uses the default two cell specifier as described in +Documentation/devicetree/bindings/interrupt-controller/interrupts.txt. + +Example: + + gpioext: gpio-controller@41 { + compatible = "ad,gpio-adnp"; + reg = <0x41>; + + interrupt-parent = <&gpio>; + interrupts = <160 1>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + + nr-gpios = <64>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-fan.txt b/Documentation/devicetree/bindings/gpio/gpio-fan.txt new file mode 100644 index 00000000000..2dd457a3469 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-fan.txt @@ -0,0 +1,25 @@ +Bindings for fan connected to GPIO lines + +Required properties: +- compatible : "gpio-fan" +- gpios: Specifies the pins that map to bits in the control value, + ordered MSB-->LSB. +- gpio-fan,speed-map: A mapping of possible fan RPM speeds and the + control value that should be set to achieve them. This array + must have the RPM values in ascending order. + +Optional properties: +- alarm-gpios: This pin going active indicates something is wrong with + the fan, and a udev event will be fired. + +Examples: + + gpio_fan { + compatible = "gpio-fan"; + gpios = <&gpio1 14 1 + &gpio1 13 1>; + gpio-fan,speed-map = <0 0 + 3000 1 + 6000 2>; + alarm-gpios = <&gpio1 15 1>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt new file mode 100644 index 00000000000..a6f3bec1da7 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt @@ -0,0 +1,53 @@ +* Marvell EBU GPIO controller + +Required properties: + +- compatible : Should be "marvell,orion-gpio", "marvell,mv78200-gpio" + or "marvell,armadaxp-gpio". "marvell,orion-gpio" should be used for + Orion, Kirkwood, Dove, Discovery (except MV78200) and Armada + 370. "marvell,mv78200-gpio" should be used for the Discovery + MV78200. "marvel,armadaxp-gpio" should be used for all Armada XP + SoCs (MV78230, MV78260, MV78460). + +- reg: Address and length of the register set for the device. Only one + entry is expected, except for the "marvell,armadaxp-gpio" variant + for which two entries are expected: one for the general registers, + one for the per-cpu registers. + +- interrupts: The list of interrupts that are used for all the pins + managed by this GPIO bank. There can be more than one interrupt + (example: 1 interrupt per 8 pins on Armada XP, which means 4 + interrupts per bank of 32 GPIOs). + +- interrupt-controller: identifies the node as an interrupt controller + +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. Should be two. + The first cell is the GPIO number. + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + +- gpio-controller: marks the device node as a gpio controller + +- ngpios: number of GPIOs this controller has + +- #gpio-cells: Should be two. The first cell is the pin number. The + second cell is reserved for flags, unused at the moment. + +Example: + + gpio0: gpio@d0018100 { + compatible = "marvell,armadaxp-gpio"; + reg = <0xd0018100 0x40>, + <0xd0018800 0x30>; + ngpios = <32>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <16>, <17>, <18>, <19>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt index 5375625e8cd..f1e5dfecf55 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt @@ -39,3 +39,46 @@ Example: #gpio-cells = <4>; gpio-controller; }; + + +Samsung S3C24XX GPIO Controller + +Required properties: +- compatible: Compatible property value should be "samsung,s3c24xx-gpio". + +- reg: Physical base address of the controller and length of memory mapped + region. + +- #gpio-cells: Should be 3. The syntax of the gpio specifier used by client nodes + should be the following with values derived from the SoC user manual. + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [mux function] + [flags and pull up/down] + + Values for gpio specifier: + - Pin number: depending on the controller a number from 0 up to 15. + - Mux function: Depending on the SoC and the gpio bank the gpio can be set + as input, output or a special function + - Flags and Pull Up/Down: the values to use differ for the individual SoCs + example S3C2416/S3C2450: + 0 - Pull Up/Down Disabled. + 1 - Pull Down Enabled. + 2 - Pull Up Enabled. + Bit 16 (0x00010000) - Input is active low. + Consult the user manual for the correct values of Mux and Pull Up/Down. + +- gpio-controller: Specifies that the node is a gpio controller. +- #address-cells: should be 1. +- #size-cells: should be 1. + +Example: + + gpa: gpio-controller@56000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "samsung,s3c24xx-gpio"; + reg = <0x56000000 0x10>; + #gpio-cells = <3>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt index 16695d9cf1e..66788fda1db 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt @@ -11,6 +11,11 @@ Required properties: - interrupt-controller: Mark the device node as an interrupt controller The first cell is the GPIO number. The second cell is not used. +- ti,use-leds : Enables LEDA and LEDB outputs if set +- ti,debounce : if n-th bit is set, debounces GPIO-n +- ti,mmc-cd : if n-th bit is set, GPIO-n controls VMMC(n+1) +- ti,pullups : if n-th bit is set, set a pullup on GPIO-n +- ti,pulldowns : if n-th bit is set, set a pulldown on GPIO-n Example: @@ -20,4 +25,5 @@ twl_gpio: gpio { gpio-controller; #interrupt-cells = <2>; interrupt-controller; + ti,use-leds; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt b/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt new file mode 100644 index 00000000000..f4dc5233167 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt @@ -0,0 +1,24 @@ +VIA/Wondermedia VT8500 GPIO Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-gpio", "wm,wm8505-gpio" + or "wm,wm8650-gpio" depending on your SoC +- reg : Should contain 1 register range (address and length) +- #gpio-cells : should be <3>. + 1) bank + 2) pin number + 3) flags - should be 0 + +Example: + + gpio: gpio-controller@d8110000 { + compatible = "via,vt8500-gpio"; + gpio-controller; + reg = <0xd8110000 0x10000>; + #gpio-cells = <3>; + }; + + vibrate { + gpios = <&gpio 0 1 0>; /* Bank 0, Pin 1, No flags */ + }; diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt index 9bb308abd22..edc83c1c0d5 100644 --- a/Documentation/devicetree/bindings/gpio/led.txt +++ b/Documentation/devicetree/bindings/gpio/led.txt @@ -8,7 +8,7 @@ node's name represents the name of the corresponding LED. LED sub-node properties: - gpios : Should specify the LED's GPIO, see "gpios property" in - Documentation/devicetree/gpio.txt. Active low LEDs should be + Documentation/devicetree/bindings/gpio/gpio.txt. Active low LEDs should be indicated using flags in the GPIO specifier. - label : (optional) The label for this LED. If omitted, the label is taken from the node name (excluding the unit address). |