diff options
Diffstat (limited to 'Documentation/devicetree/bindings/input')
5 files changed, 260 insertions, 19 deletions
diff --git a/Documentation/devicetree/bindings/input/ads7846.txt b/Documentation/devicetree/bindings/input/ads7846.txt new file mode 100644 index 00000000000..5f7619c2274 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ads7846.txt @@ -0,0 +1,91 @@ +Device tree bindings for TI's ADS7843, ADS7845, ADS7846, ADS7873, TSC2046 +SPI driven touch screen controllers. + +The node for this driver must be a child node of a SPI controller, hence +all mandatory properties described in + + Documentation/devicetree/bindings/spi/spi-bus.txt + +must be specified. + +Additional required properties: + + compatible Must be one of the following, depending on the + model: + "ti,tsc2046" + "ti,ads7843" + "ti,ads7845" + "ti,ads7846" + "ti,ads7873" + + interrupt-parent + interrupts An interrupt node describing the IRQ line the chip's + !PENIRQ pin is connected to. + vcc-supply A regulator node for the supply voltage. + + +Optional properties: + + ti,vref-delay-usecs vref supply delay in usecs, 0 for + external vref (u16). + ti,vref-mv The VREF voltage, in millivolts (u16). + ti,keep-vref-on set to keep vref on for differential + measurements as well + ti,swap-xy swap x and y axis + ti,settle-delay-usec Settling time of the analog signals; + a function of Vcc and the capacitance + on the X/Y drivers. If set to non-zero, + two samples are taken with settle_delay + us apart, and the second one is used. + ~150 uSec with 0.01uF caps (u16). + ti,penirq-recheck-delay-usecs If set to non-zero, after samples are + taken this delay is applied and penirq + is rechecked, to help avoid false + events. This value is affected by the + material used to build the touch layer + (u16). + ti,x-plate-ohms Resistance of the X-plate, + in Ohms (u16). + ti,y-plate-ohms Resistance of the Y-plate, + in Ohms (u16). + ti,x-min Minimum value on the X axis (u16). + ti,y-min Minimum value on the Y axis (u16). + ti,x-max Maximum value on the X axis (u16). + ti,y-max Minimum value on the Y axis (u16). + ti,pressure-min Minimum reported pressure value + (threshold) - u16. + ti,pressure-max Maximum reported pressure value (u16). + ti,debounce-max Max number of additional readings per + sample (u16). + ti,debounce-tol Tolerance used for filtering (u16). + ti,debounce-rep Additional consecutive good readings + required after the first two (u16). + ti,pendown-gpio-debounce Platform specific debounce time for the + pendown-gpio (u32). + pendown-gpio GPIO handle describing the pin the !PENIRQ + line is connected to. + linux,wakeup use any event on touchscreen as wakeup event. + + +Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC:: + + spi_controller { + tsc2046@0 { + reg = <0>; /* CS0 */ + compatible = "ti,tsc2046"; + interrupt-parent = <&gpio1>; + interrupts = <8 0>; /* BOOT6 / GPIO 8 */ + spi-max-frequency = <1000000>; + pendown-gpio = <&gpio1 8 0>; + vcc-supply = <®_vcc3>; + + ti,x-min = /bits/ 16 <0>; + ti,x-max = /bits/ 16 <8000>; + ti,y-min = /bits/ 16 <0>; + ti,y-max = /bits/ 16 <4800>; + ti,x-plate-ohms = /bits/ 16 <40>; + ti,pressure-max = /bits/ 16 <255>; + + linux,wakeup; + }; + }; diff --git a/Documentation/devicetree/bindings/input/pxa27x-keypad.txt b/Documentation/devicetree/bindings/input/pxa27x-keypad.txt new file mode 100644 index 00000000000..f8674f7e5ea --- /dev/null +++ b/Documentation/devicetree/bindings/input/pxa27x-keypad.txt @@ -0,0 +1,60 @@ +* Marvell PXA Keypad controller + +Required Properties +- compatible : should be "marvell,pxa27x-keypad" +- reg : Address and length of the register set for the device +- interrupts : The interrupt for the keypad controller +- marvell,debounce-interval : How long time the key will be + recognized when it is pressed. It is a u32 value, and bit[31:16] + is debounce interval for direct key and bit[15:0] is debounce + interval for matrix key. The value is in binary number of 2ms + +Optional Properties For Matrix Keyes +Please refer to matrix-keymap.txt + +Optional Properties for Direct Keyes +- marvell,direct-key-count : How many direct keyes are used. +- marvell,direct-key-mask : The mask indicates which keyes + are used. If bit[X] of the mask is set, the direct key X + is used. +- marvell,direct-key-low-active : Direct key status register + tells the level of pins that connects to the direct keyes. + When this property is set, it means that when the pin level + is low, the key is pressed(active). +- marvell,direct-key-map : It is a u16 array. Each item indicates + the linux key-code for the direct key. + +Optional Properties For Rotary +- marvell,rotary0 : It is a u32 value. Bit[31:16] is the + linux key-code for rotary up. Bit[15:0] is the linux key-code + for rotary down. It is for rotary 0. +- marvell,rotary1 : Same as marvell,rotary0. It is for rotary 1. +- marvell,rotary-rel-key : When rotary is used for relative axes + in the device, the value indicates the key-code for relative + axes measurement in the device. It is a u32 value. Bit[31:16] + is for rotary 1, and Bit[15:0] is for rotary 0. + +Examples: + keypad: keypad@d4012000 { + keypad,num-rows = <3>; + keypad,num-columns = <5>; + linux,keymap = <0x0000000e /* KEY_BACKSPACE */ + 0x0001006b /* KEY_END */ + 0x00020061 /* KEY_RIGHTCTRL */ + 0x0003000b /* KEY_0 */ + 0x00040002 /* KEY_1 */ + 0x0100008b /* KEY_MENU */ + 0x01010066 /* KEY_HOME */ + 0x010200e7 /* KEY_SEND */ + 0x01030009 /* KEY_8 */ + 0x0104000a /* KEY_9 */ + 0x02000160 /* KEY_OK */ + 0x02010003 /* KEY_2 */ + 0x02020004 /* KEY_3 */ + 0x02030005 /* KEY_4 */ + 0x02040006>; /* KEY_5 */ + marvell,rotary0 = <0x006c0067>; /* KEY_UP & KEY_DOWN */ + marvell,direct-key-count = <1>; + marvell,direct-key-map = <0x001c>; + marvell,debounce-interval = <0x001e001e>; + }; diff --git a/Documentation/devicetree/bindings/input/samsung-keypad.txt b/Documentation/devicetree/bindings/input/samsung-keypad.txt index ce3e394c0e6..942d071baaa 100644 --- a/Documentation/devicetree/bindings/input/samsung-keypad.txt +++ b/Documentation/devicetree/bindings/input/samsung-keypad.txt @@ -25,14 +25,6 @@ Required Board Specific Properties: - samsung,keypad-num-columns: Number of column lines connected to the keypad controller. -- row-gpios: List of gpios used as row lines. The gpio specifier for - this property depends on the gpio controller to which these row lines - are connected. - -- col-gpios: List of gpios used as column lines. The gpio specifier for - this property depends on the gpio controller to which these column - lines are connected. - - Keys represented as child nodes: Each key connected to the keypad controller is represented as a child node to the keypad controller device node and should include the following properties. @@ -41,6 +33,9 @@ Required Board Specific Properties: - linux,code: the key-code to be reported when the key is pressed and released. +- pinctrl-0: Should specify pin control groups used for this controller. +- pinctrl-names: Should contain only one value - "default". + Optional Properties specific to linux: - linux,keypad-no-autorepeat: do no enable autorepeat feature. - linux,keypad-wakeup: use any event on keypad as wakeup event. @@ -56,17 +51,8 @@ Example: linux,input-no-autorepeat; linux,input-wakeup; - row-gpios = <&gpx2 0 3 3 0 - &gpx2 1 3 3 0>; - - col-gpios = <&gpx1 0 3 0 0 - &gpx1 1 3 0 0 - &gpx1 2 3 0 0 - &gpx1 3 3 0 0 - &gpx1 4 3 0 0 - &gpx1 5 3 0 0 - &gpx1 6 3 0 0 - &gpx1 7 3 0 0>; + pinctrl-names = "default"; + pinctrl-0 = <&keypad_rows &keypad_columns>; key_1 { keypad,row = <0>; diff --git a/Documentation/devicetree/bindings/input/ti,nspire-keypad.txt b/Documentation/devicetree/bindings/input/ti,nspire-keypad.txt new file mode 100644 index 00000000000..513d94d6e89 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,nspire-keypad.txt @@ -0,0 +1,60 @@ +TI-NSPIRE Keypad + +Required properties: +- compatible: Compatible property value should be "ti,nspire-keypad". + +- reg: Physical base address of the peripheral and length of memory mapped + region. + +- interrupts: The interrupt number for the peripheral. + +- scan-interval: How often to scan in us. Based on a APB speed of 33MHz, the + maximum and minimum delay time is ~2000us and ~500us respectively + +- row-delay: How long to wait before scanning each row. + +- clocks: The clock this peripheral is attached to. + +- linux,keymap: The keymap to use + (see Documentation/devicetree/bindings/input/matrix-keymap.txt) + +Optional properties: +- active-low: Specify that the keypad is active low (i.e. logical low signifies + a key press). + +Example: + +input { + compatible = "ti,nspire-keypad"; + reg = <0x900E0000 0x1000>; + interrupts = <16>; + + scan-interval = <1000>; + row-delay = <200>; + + clocks = <&apb_pclk>; + + linux,keymap = < + 0x0000001c 0x0001001c 0x00040039 + 0x0005002c 0x00060015 0x0007000b + 0x0008000f 0x0100002d 0x01010011 + 0x0102002f 0x01030004 0x01040016 + 0x01050014 0x0106001f 0x01070002 + 0x010a006a 0x02000013 0x02010010 + 0x02020019 0x02030007 0x02040018 + 0x02050031 0x02060032 0x02070005 + 0x02080028 0x0209006c 0x03000026 + 0x03010025 0x03020024 0x0303000a + 0x03040017 0x03050023 0x03060022 + 0x03070008 0x03080035 0x03090069 + 0x04000021 0x04010012 0x04020020 + 0x0404002e 0x04050030 0x0406001e + 0x0407000d 0x04080037 0x04090067 + 0x05010038 0x0502000c 0x0503001b + 0x05040034 0x0505001a 0x05060006 + 0x05080027 0x0509000e 0x050a006f + 0x0600002b 0x0602004e 0x06030068 + 0x06040003 0x0605006d 0x06060009 + 0x06070001 0x0609000f 0x0708002a + 0x0709001d 0x070a0033 >; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt new file mode 100644 index 00000000000..491c97b7838 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt @@ -0,0 +1,44 @@ +* TI - TSC ADC (Touschscreen and analog digital converter) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Required properties: +- child "tsc" + ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen + support on the platform. + ti,x-plate-resistance: X plate resistance + ti,coordiante-readouts: The sequencer supports a total of 16 + programmable steps each step is used to + read a single coordinate. A single + readout is enough but multiple reads can + increase the quality. + A value of 5 means, 5 reads for X, 5 for + Y and 2 for Z (always). This utilises 12 + of the 16 software steps available. The + remaining 4 can be used by the ADC. + ti,wire-config: Different boards could have a different order for + connecting wires on touchscreen. We need to provide an + 8 bit number where in the 1st four bits represent the + analog lines and the next 4 bits represent positive/ + negative terminal on that input line. Notations to + represent the input lines and terminals resoectively + is as follows: + AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. + XP = 0, XN = 1, YP = 2, YN = 3. +- child "adc" + ti,adc-channels: List of analog inputs available for ADC. + AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. + +Example: + tscadc: tscadc@44e0d000 { + compatible = "ti,am3359-tscadc"; + tsc { + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,coordiante-readouts = <5>; + ti,wire-config = <0x00 0x11 0x22 0x33>; + }; + + adc { + ti,adc-channels = <4 5 6 7>; + }; + } |