diff options
Diffstat (limited to 'Documentation/devicetree/bindings/input')
7 files changed, 218 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt new file mode 100644 index 00000000000..1852906517a --- /dev/null +++ b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt @@ -0,0 +1,32 @@ +Atmel maXTouch touchscreen/touchpad + +Required properties: +- compatible: + atmel,maxtouch + +- reg: The I2C address of the device + +- interrupts: The sink for the touchpad's IRQ output + See ../interrupt-controller/interrupts.txt + +Optional properties for main touchpad device: + +- linux,gpio-keymap: When enabled, the SPT_GPIOPWN_T19 object sends messages + on GPIO bit changes. An array of up to 8 entries can be provided + indicating the Linux keycode mapped to each bit of the status byte, + starting at the LSB. Linux keycodes are defined in + <dt-bindings/input/input.h>. + + Note: the numbering of the GPIOs and the bit they start at varies between + maXTouch devices. You must either refer to the documentation, or + experiment to determine which bit corresponds to which input. Use + KEY_RESERVED for unused padding values. + +Example: + + touch@4b { + compatible = "atmel,maxtouch"; + reg = <0x4b>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_LOW>; + }; diff --git a/Documentation/devicetree/bindings/input/cap1106.txt b/Documentation/devicetree/bindings/input/cap1106.txt new file mode 100644 index 00000000000..4b463904cba --- /dev/null +++ b/Documentation/devicetree/bindings/input/cap1106.txt @@ -0,0 +1,53 @@ +Device tree bindings for Microchip CAP1106, 6 channel capacitive touch sensor + +The node for this driver must be a child of a I2C controller node, as the +device communication via I2C only. + +Required properties: + + compatible: Must be "microchip,cap1106" + + reg: The I2C slave address of the device. + Only 0x28 is valid. + + interrupts: Property describing the interrupt line the + device's ALERT#/CM_IRQ# pin is connected to. + The device only has one interrupt source. + +Optional properties: + + autorepeat: Enables the Linux input system's autorepeat + feature on the input device. + + microchip,sensor-gain: Defines the gain of the sensor circuitry. This + effectively controls the sensitivity, as a + smaller delta capacitance is required to + generate the same delta count values. + Valid values are 1, 2, 4, and 8. + By default, a gain of 1 is set. + + linux,keycodes: Specifies an array of numeric keycode values to + be used for the channels. If this property is + omitted, KEY_A, KEY_B, etc are used as + defaults. The array must have exactly six + entries. + +Example: + +i2c_controller { + cap1106@28 { + compatible = "microchip,cap1106"; + interrupt-parent = <&gpio1>; + interrupts = <0 0>; + reg = <0x28>; + autorepeat; + microchip,sensor-gain = <2>; + + linux,keycodes = <103 /* KEY_UP */ + 106 /* KEY_RIGHT */ + 108 /* KEY_DOWN */ + 105 /* KEY_LEFT */ + 109 /* KEY_PAGEDOWN */ + 104>; /* KEY_PAGEUP */ + }; +} diff --git a/Documentation/devicetree/bindings/input/ti,drv260x.txt b/Documentation/devicetree/bindings/input/ti,drv260x.txt new file mode 100644 index 00000000000..ee09c8f4474 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,drv260x.txt @@ -0,0 +1,50 @@ +* Texas Instruments - drv260x Haptics driver family + +Required properties: + - compatible - One of: + "ti,drv2604" - DRV2604 + "ti,drv2605" - DRV2605 + "ti,drv2605l" - DRV2605L + - reg - I2C slave address + - vbat-supply - Required supply regulator + - mode - Power up mode of the chip (defined in include/dt-bindings/input/ti-drv260x.h) + DRV260X_LRA_MODE - Linear Resonance Actuator mode (Piezoelectric) + DRV260X_LRA_NO_CAL_MODE - This is a LRA Mode but there is no calibration + sequence during init. And the device is configured for real + time playback mode (RTP mode). + DRV260X_ERM_MODE - Eccentric Rotating Mass mode (Rotary vibrator) + - library-sel - These are ROM based waveforms pre-programmed into the IC. + This should be set to set the library to use at power up. + (defined in include/dt-bindings/input/ti-drv260x.h) + DRV260X_LIB_EMPTY - Do not use a pre-programmed library + DRV260X_ERM_LIB_A - Pre-programmed Library + DRV260X_ERM_LIB_B - Pre-programmed Library + DRV260X_ERM_LIB_C - Pre-programmed Library + DRV260X_ERM_LIB_D - Pre-programmed Library + DRV260X_ERM_LIB_E - Pre-programmed Library + DRV260X_ERM_LIB_F - Pre-programmed Library + DRV260X_LIB_LRA - Pre-programmed LRA Library + +Optional properties: + - enable-gpio - gpio pin to enable/disable the device. + - vib-rated-mv - The rated voltage of the actuator in millivolts. + If this is not set then the value will be defaulted to + 3.2 v. + - vib-overdrive-mv - The overdrive voltage of the actuator in millivolts. + If this is not set then the value will be defaulted to + 3.2 v. +Example: + +haptics: haptics@5a { + compatible = "ti,drv2605l"; + reg = <0x5a>; + vbat-supply = <&vbat>; + enable-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>; + mode = <DRV260X_LRA_MODE>; + library-sel = <DRV260X_LIB_LRA>; + vib-rated-mv = <3200>; + vib-overdriver-mv = <3200>; +} + +For more product information please see the link below: +http://www.ti.com/product/drv2605 diff --git a/Documentation/devicetree/bindings/input/ti,drv2667.txt b/Documentation/devicetree/bindings/input/ti,drv2667.txt new file mode 100644 index 00000000000..996382cf994 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,drv2667.txt @@ -0,0 +1,17 @@ +* Texas Instruments - drv2667 Haptics driver + +Required properties: + - compatible - "ti,drv2667" - DRV2667 + - reg - I2C slave address + - vbat-supply - Required supply regulator + +Example: + +haptics: haptics@59 { + compatible = "ti,drv2667"; + reg = <0x59>; + vbat-supply = <&vbat>; +}; + +For more product information please see the link below: +http://www.ti.com/product/drv2667 diff --git a/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt b/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt new file mode 100644 index 00000000000..a3dde8c30e6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt @@ -0,0 +1,36 @@ +Texas Instruments Palmas family power button module + +This module is part of the Palmas family of PMICs. For more details +about the whole chip see: +Documentation/devicetree/bindings/mfd/palmas.txt. + +This module provides a simple power button event via an Interrupt. + +Required properties: +- compatible: should be one of the following + - "ti,palmas-pwrbutton": For Palmas compatible power on button +- interrupt-parent: Parent interrupt device, must be handle of palmas node. +- interrupts: Interrupt number of power button submodule on device. + +Optional Properties: + +- ti,palmas-long-press-seconds: Duration in seconds which the power + button should be kept pressed for Palmas to power off automatically. + NOTE: This depends on OTP support and POWERHOLD signal configuration + on platform. Valid values are 6, 8, 10 and 12. +- ti,palmas-pwron-debounce-milli-seconds: Duration in milliseconds + which the power button should be kept pressed for Palmas to register + a press for debouncing purposes. NOTE: This depends on specific + Palmas variation capability. Valid values are 15, 100, 500 and 1000. + +Example: + +&palmas { + palmas_pwr_button: pwrbutton { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&tps659038>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + ti,palmas-long-press-seconds = <12>; + ti,palmas-pwron-debounce-milli-seconds = <15>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt new file mode 100644 index 00000000000..6e551090f46 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt @@ -0,0 +1,26 @@ +* Pixcir I2C touchscreen controllers + +Required properties: +- compatible: must be "pixcir,pixcir_ts" or "pixcir,pixcir_tangoc" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- attb-gpio: GPIO connected to the ATTB line of the chip +- touchscreen-size-x: horizontal resolution of touchscreen (in pixels) +- touchscreen-size-y: vertical resolution of touchscreen (in pixels) + +Example: + + i2c@00000000 { + /* ... */ + + pixcir_ts@5c { + compatible = "pixcir,pixcir_ts"; + reg = <0x5c>; + interrupts = <2 0>; + attb-gpio = <&gpf 2 0 2>; + touchscreen-size-x = <800>; + touchscreen-size-y = <600>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt index 2faf1f1fa39..80c37df940a 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt @@ -9,6 +9,9 @@ Required properties: - x-size: horizontal resolution of touchscreen - y-size: vertical resolution of touchscreen +Optional properties: +- vdd-supply: Regulator controlling the controller supply + Example: i2c@00000000 { @@ -18,6 +21,7 @@ Example: compatible = "neonode,zforce"; reg = <0x50>; interrupts = <2 0>; + vdd-supply = <®_zforce_vdd>; gpios = <&gpio5 6 0>, /* INT */ <&gpio5 9 0>; /* RST */ |