1 files changed, 87 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
new file mode 100644
index 00000000000..79276895333
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
@@ -0,0 +1,87 @@
+* Samsung Exynos specific extensions to the Synopsis Designware Mobile
+  Storage Host Controller
+
+The Synopsis designware mobile storage host controller is used to interface
+a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
+differences between the core Synopsis dw mshc controller properties described
+by synposis-dw-mshc.txt and the properties used by the Samsung Exynos specific
+extensions to the Synopsis Designware Mobile Storage Host Controller.
+
+Required Properties:
+
+* compatible: should be
+	- "samsung,exynos4210-dw-mshc": for controllers with Samsung Exynos4210
+	  specific extentions.
+	- "samsung,exynos4412-dw-mshc": for controllers with Samsung Exynos4412
+	  specific extentions.
+	- "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250
+	  specific extentions.
+
+* samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface
+  unit (ciu) clock. This property is applicable only for Exynos5 SoC's and
+  ignored for Exynos4 SoC's. The valid range of divider value is 0 to 7.
+
+* samsung,dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift value
+  in transmit mode and CIU clock phase shift value in receive mode for single
+  data rate mode operation. Refer notes below for the order of the cells and the
+  valid values.
+
+* samsung,dw-mshc-ddr-timing: Specifies the value of CUI clock phase shift value
+  in transmit mode and CIU clock phase shift value in receive mode for double
+  data rate mode operation. Refer notes below for the order of the cells and the
+  valid values.
+
+  Notes for the sdr-timing and ddr-timing values:
+
+    The order of the cells should be
+      - First Cell: CIU clock phase shift value for tx mode.
+      - Second Cell: CIU clock phase shift value for rx mode.
+
+    Valid values for SDR and DDR CIU clock timing for Exynos5250:
+      - valid value for tx phase shift and rx phase shift is 0 to 7.
+      - when CIU clock divider value is set to 3, all possible 8 phase shift
+        values can be used.
+      - if CIU clock divider value is 0 (that is divide by 1), both tx and rx
+        phase shift clocks should be 0.
+
+Required properties for a slot:
+
+* gpios: specifies a list of gpios used for command, clock and data bus. The
+  first gpio is the command line and the second gpio is the clock line. The
+  rest of the gpios (depending on the bus-width property) are the data lines in
+  no particular order. The format of the gpio specifier depends on the gpio
+  controller.
+
+Example:
+
+  The MSHC controller node can be split into two portions, SoC specific and
+  board specific portions as listed below.
+
+	dwmmc0@12200000 {
+		compatible = "samsung,exynos5250-dw-mshc";
+		reg = <0x12200000 0x1000>;
+		interrupts = <0 75 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	dwmmc0@12200000 {
+		num-slots = <1>;
+		supports-highspeed;
+		broken-cd;
+		fifo-depth = <0x80>;
+		card-detect-delay = <200>;
+		samsung,dw-mshc-ciu-div = <3>;
+		samsung,dw-mshc-sdr-timing = <2 3>;
+		samsung,dw-mshc-ddr-timing = <1 2>;
+
+		slot@0 {
+			reg = <0>;
+			bus-width = <8>;
+			gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
+				<&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
+				<&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>,
+				<&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
+				<&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>;
+		};
+	};