diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/rockchip-dwmac.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/net/rockchip-dwmac.txt | 68 |
1 files changed, 68 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt new file mode 100644 index 00000000000..21fd199e89b --- /dev/null +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt @@ -0,0 +1,68 @@ +Rockchip SoC RK3288 10/100/1000 Ethernet driver(GMAC) + +The device node has following properties. + +Required properties: + - compatible: Can be "rockchip,rk3288-gmac". + - reg: addresses and length of the register sets for the device. + - interrupts: Should contain the GMAC interrupts. + - interrupt-names: Should contain the interrupt names "macirq". + - rockchip,grf: phandle to the syscon grf used to control speed and mode. + - clocks: <&cru SCLK_MAC>: clock selector for main clock, from PLL or PHY. + <&cru SCLK_MAC_PLL>: PLL clock for SCLK_MAC + <&cru SCLK_MAC_RX>: clock gate for RX + <&cru SCLK_MAC_TX>: clock gate for TX + <&cru SCLK_MACREF>: clock gate for RMII referce clock + <&cru SCLK_MACREF_OUT> clock gate for RMII reference clock output + <&cru ACLK_GMAC>: AXI clock gate for GMAC + <&cru PCLK_GMAC>: APB clock gate for GMAC + - clock-names: One name for each entry in the clocks property. + - phy-mode: See ethernet.txt file in the same directory. + - pinctrl-names: Names corresponding to the numbered pinctrl states. + - pinctrl-0: pin-control mode. can be <&rgmii_pins> or <&rmii_pins>. + - clock_in_out: For RGMII, it must be "input", means main clock(125MHz) + is not sourced from SoC's PLL, but input from PHY; For RMII, "input" means + PHY provides the reference clock(50MHz), "output" means GMAC provides the + reference clock. + - snps,reset-gpio gpio number for phy reset. + - snps,reset-active-low boolean flag to indicate if phy reset is active low. + - assigned-clocks: main clock, should be <&cru SCLK_MAC>; + - assigned-clock-parents = parent of main clock. + can be <&ext_gmac> or <&cru SCLK_MAC_PLL>. + +Optional properties: + - tx_delay: Delay value for TXD timing. Range value is 0~0x7F, 0x30 as default. + - rx_delay: Delay value for RXD timing. Range value is 0~0x7F, 0x10 as default. + - phy-supply: phandle to a regulator if the PHY needs one + +Example: + +gmac: ethernet@ff290000 { + compatible = "rockchip,rk3288-gmac"; + reg = <0xff290000 0x10000>; + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + rockchip,grf = <&grf>; + clocks = <&cru SCLK_MAC>, + <&cru SCLK_MAC_RX>, <&cru SCLK_MAC_TX>, + <&cru SCLK_MACREF>, <&cru SCLK_MACREF_OUT>, + <&cru ACLK_GMAC>, <&cru PCLK_GMAC>; + clock-names = "stmmaceth", + "mac_clk_rx", "mac_clk_tx", + "clk_mac_ref", "clk_mac_refout", + "aclk_mac", "pclk_mac"; + phy-mode = "rgmii"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins /*&rmii_pins*/>; + + clock_in_out = "input"; + snps,reset-gpio = <&gpio4 7 0>; + snps,reset-active-low; + + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + tx_delay = <0x30>; + rx_delay = <0x10>; + + status = "ok"; +}; |