diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
5 files changed, 226 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt new file mode 100644 index 00000000000..2fa4fcd38fd --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt @@ -0,0 +1,53 @@ +CAN Device Tree Bindings +------------------------ + +(c) 2006-2009 Secret Lab Technologies Ltd +Grant Likely <grant.likely@secretlab.ca> + +fsl,mpc5200-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock (XTAL) + "ref" is default in case this property is not + present. + +fsl,mpc5121-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source and divider shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock + "sys" for system clock + If this property is not present, an optimal CAN + clock source and frequency based on the system + clock will be selected. If this is not possible, + the reference clock will be used. + +- fsl,mscan-clock-divider: for the reference and system clock, an additional + clock divider can be specified. By default, a + value of 1 is used. + +Note that the MPC5121 Rev. 1 processor is not supported. + +Examples: + can@1300 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <12 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1300 0x80>; + }; + + can@1380 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <13 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1380 0x80>; + fsl,mscan-clock-source = "ref"; + fsl,mscan-clock-divider = <3>; + }; diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt new file mode 100644 index 00000000000..d6d209ded93 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/sja1000.txt @@ -0,0 +1,53 @@ +Memory mapped SJA1000 CAN controller from NXP (formerly Philips) + +Required properties: + +- compatible : should be "nxp,sja1000". + +- reg : should specify the chip select, address offset and size required + to map the registers of the SJA1000. The size is usually 0x80. + +- interrupts: property with a value describing the interrupt source + (number and sensitivity) required for the SJA1000. + +Optional properties: + +- nxp,external-clock-frequency : Frequency of the external oscillator + clock in Hz. Note that the internal clock frequency used by the + SJA1000 is half of that value. If not specified, a default value + of 16000000 (16 MHz) is used. + +- nxp,tx-output-mode : operation mode of the TX output control logic: + <0x0> : bi-phase output mode + <0x1> : normal output mode (default) + <0x2> : test output mode + <0x3> : clock output mode + +- nxp,tx-output-config : TX output pin configuration: + <0x01> : TX0 invert + <0x02> : TX0 pull-down (default) + <0x04> : TX0 pull-up + <0x06> : TX0 push-pull + <0x08> : TX1 invert + <0x10> : TX1 pull-down + <0x20> : TX1 pull-up + <0x30> : TX1 push-pull + +- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin. + If not specified or if the specified value is 0, the CLKOUT pin + will be disabled. + +- nxp,no-comparator-bypass : Allows to disable the CAN input comperator. + +For futher information, please have a look to the SJA1000 data sheet. + +Examples: + +can@3,100 { + compatible = "nxp,sja1000"; + reg = <3 0x100 0x80>; + interrupts = <2 0>; + interrupt-parent = <&mpic>; + nxp,external-clock-frequency = <16000000>; +}; + diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt new file mode 100644 index 00000000000..edb7ae19e86 --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -0,0 +1,76 @@ +* MDIO IO device + +The MDIO is a bus to which the PHY devices are connected. For each +device that exists on this bus, a child node should be created. See +the definition of the PHY node in booting-without-of.txt for an example +of how to define a PHY. + +Required properties: + - reg : Offset and length of the register set for the device + - compatible : Should define the compatible device type for the + mdio. Currently, this is most likely to be "fsl,gianfar-mdio" + +Example: + + mdio@24520 { + reg = <24520 20>; + compatible = "fsl,gianfar-mdio"; + + ethernet-phy@0 { + ...... + }; + }; + +* TBI Internal MDIO bus + +As of this writing, every tsec is associated with an internal TBI PHY. +This PHY is accessed through the local MDIO bus. These buses are defined +similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi". +The TBI PHYs underneath them are similar to normal PHYs, but the reg property +is considered instructive, rather than descriptive. The reg property should +be chosen so it doesn't interfere with other PHYs on the bus. + +* Gianfar-compatible ethernet nodes + +Properties: + + - device_type : Should be "network" + - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC" + - compatible : Should be "gianfar" + - reg : Offset and length of the register set for the device + - local-mac-address : List of bytes representing the ethernet address of + this controller + - interrupts : For FEC devices, the first interrupt is the device's + interrupt. For TSEC and eTSEC devices, the first interrupt is + transmit, the second is receive, and the third is error. + - phy-handle : The phandle for the PHY connected to this ethernet + controller. + - fixed-link : <a b c d e> where a is emulated phy id - choose any, + but unique to the all specified fixed-links, b is duplex - 0 half, + 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no + pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause. + - phy-connection-type : a string naming the controller/PHY interface type, + i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii", + "tbi", or "rtbi". This property is only really needed if the connection + is of type "rgmii-id", as all other connection types are detected by + hardware. + - fsl,magic-packet : If present, indicates that the hardware supports + waking up via magic packet. + - bd-stash : If present, indicates that the hardware supports stashing + buffer descriptors in the L2. + - rx-stash-len : Denotes the number of bytes of a received buffer to stash + in the L2. + - rx-stash-idx : Denotes the index of the first byte from the received + buffer to stash in the L2. + +Example: + ethernet@24000 { + device_type = "network"; + model = "TSEC"; + compatible = "gianfar"; + reg = <0x24000 0x1000>; + local-mac-address = [ 00 E0 0C 00 73 00 ]; + interrupts = <29 2 30 2 34 2>; + interrupt-parent = <&mpic>; + phy-handle = <&phy0> + }; diff --git a/Documentation/devicetree/bindings/net/mdio-gpio.txt b/Documentation/devicetree/bindings/net/mdio-gpio.txt new file mode 100644 index 00000000000..bc954952901 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-gpio.txt @@ -0,0 +1,19 @@ +MDIO on GPIOs + +Currently defined compatibles: +- virtual,gpio-mdio + +MDC and MDIO lines connected to GPIO controllers are listed in the +gpios property as described in section VIII.1 in the following order: + +MDC, MDIO. + +Example: + +mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qe_pio_a 11 + &qe_pio_c 6>; +}; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt new file mode 100644 index 00000000000..bb8c742eb8c --- /dev/null +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -0,0 +1,25 @@ +PHY nodes + +Required properties: + + - device_type : Should be "ethernet-phy" + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - reg : The ID number for the phy, usually a small integer + - linux,phandle : phandle for this node; likely referenced by an + ethernet controller node. + +Example: + +ethernet-phy@0 { + linux,phandle = <2452000> + interrupt-parent = <40000>; + interrupts = <35 1>; + reg = <0>; + device_type = "ethernet-phy"; +}; |