diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci')
| -rw-r--r-- | Documentation/devicetree/bindings/pci/designware-pcie.txt | 7 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/pci/mvebu-pci.txt | 10 |
2 files changed, 16 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index e216af35684..d5d26d44369 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -3,7 +3,7 @@ Required properties: - compatible: should contain "snps,dw-pcie" to identify the core, plus an identifier for the specific instance, such - as "samsung,exynos5440-pcie". + as "samsung,exynos5440-pcie" or "fsl,imx6q-pcie". - reg: base addresses and lengths of the pcie controller, the phy controller, additional register for the phy controller. - interrupts: interrupt values for level interrupt, @@ -21,6 +21,11 @@ Required properties: - num-lanes: number of lanes to use - reset-gpio: gpio pin number of power good signal +Optional properties for fsl,imx6q-pcie +- power-on-gpio: gpio pin number of power-enable signal +- wake-up-gpio: gpio pin number of incoming wakeup signal +- disable-gpio: gpio pin number of outgoing rfkill/endpoint disable signal + Example: SoC specific DT Entry: diff --git a/Documentation/devicetree/bindings/pci/mvebu-pci.txt b/Documentation/devicetree/bindings/pci/mvebu-pci.txt index 9556e2fedf6..08c716b2c6b 100644 --- a/Documentation/devicetree/bindings/pci/mvebu-pci.txt +++ b/Documentation/devicetree/bindings/pci/mvebu-pci.txt @@ -5,6 +5,7 @@ Mandatory properties: - compatible: one of the following values: marvell,armada-370-pcie marvell,armada-xp-pcie + marvell,dove-pcie marvell,kirkwood-pcie - #address-cells, set to <3> - #size-cells, set to <2> @@ -14,6 +15,8 @@ Mandatory properties: - ranges: ranges describing the MMIO registers to control the PCIe interfaces, and ranges describing the MBus windows needed to access the memory and I/O regions of each PCIe interface. +- msi-parent: Link to the hardware entity that serves as the Message + Signaled Interrupt controller for this PCI controller. The ranges describing the MMIO registers have the following layout: @@ -74,6 +77,8 @@ and the following optional properties: - marvell,pcie-lane: the physical PCIe lane number, for ports having multiple lanes. If this property is not found, we assume that the value is 0. +- reset-gpios: optional gpio to PERST# +- reset-delay-us: delay in us to wait after reset de-assertion Example: @@ -86,6 +91,7 @@ pcie-controller { #size-cells = <2>; bus-range = <0x00 0xff>; + msi-parent = <&mpic>; ranges = <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */ @@ -135,6 +141,10 @@ pcie-controller { interrupt-map = <0 0 0 0 &mpic 58>; marvell,pcie-port = <0>; marvell,pcie-lane = <0>; + /* low-active PERST# reset on GPIO 25 */ + reset-gpios = <&gpio0 25 1>; + /* wait 20ms for device settle after reset deassertion */ + reset-delay-us = <20000>; clocks = <&gateclk 5>; status = "disabled"; }; |