diff options
Diffstat (limited to 'Documentation/devicetree/bindings/power')
3 files changed, 36 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/power/ltc2941.txt b/Documentation/devicetree/bindings/power/ltc2941.txt new file mode 100644 index 00000000000..ea42ae12d92 --- /dev/null +++ b/Documentation/devicetree/bindings/power/ltc2941.txt @@ -0,0 +1,27 @@ +binding for LTC2941 and LTC2943 battery gauges + +Both the LTC2941 and LTC2943 measure battery capacity. +The LTC2943 is compatible with the LTC2941, it adds voltage and +temperature monitoring, and uses a slightly different conversion +formula for the charge counter. + +Required properties: +- compatible: Should contain "ltc2941" or "ltc2943" which also indicates the + type of I2C chip attached. +- reg: The 7-bit I2C address. +- lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit + negative value when the battery has been connected to the wrong end of the + resistor. +- lltc,prescaler-exponent: The prescaler exponent as explained in the datasheet. + This determines the range and accuracy of the gauge. The value is programmed + into the chip only if it differs from the current setting. The setting is + lost when the battery is disconnected. + +Example from the Topic Miami Florida board: + + fuelgauge: ltc2943@64 { + compatible = "ltc2943"; + reg = <0x64>; + lltc,resistor-sense = <15>; + lltc,prescaler-exponent = <5>; /* 2^(2*5) = 1024 */ + }; diff --git a/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt index 0c94c637f63..cd2d7f58a9d 100644 --- a/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt +++ b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt @@ -1,20 +1,23 @@ Binding for the LTC2952 PowerPath controller This chip is used to externally trigger a system shut down. Once the trigger has -been sent, the chips' watchdog has to be reset to gracefully shut down. -If the Linux systems decides to shut down it powers off the platform via the -kill signal. +been sent, the chip's watchdog has to be reset to gracefully shut down. +A full powerdown can be triggered via the kill signal. Required properties: - compatible: Must contain: "lltc,ltc2952" -- trigger-gpios: phandle + gpio-specifier for the GPIO connected to the - chip's trigger line - watchdog-gpios: phandle + gpio-specifier for the GPIO connected to the chip's watchdog line - kill-gpios: phandle + gpio-specifier for the GPIO connected to the chip's kill line +Optional properties: +- trigger-gpios: phandle + gpio-specifier for the GPIO connected to the + chip's trigger line. If this property is not set, the + trigger function is ignored and the chip is kept alive + until an explicit kill signal is received + Example: ltc2952 { diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt index 6fbf6e7ecde..8b70db103ca 100644 --- a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt +++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt @@ -37,7 +37,7 @@ Required properties: You specify supplies using the standard regulator bindings by including -a phandle the the relevant regulator. All specified supplies must be able +a phandle the relevant regulator. All specified supplies must be able to report their voltage. The IO Voltage Domain for any non-specified supplies will be not be touched. |