diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound')
16 files changed, 343 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/sound/atmel_ac97c.txt b/Documentation/devicetree/bindings/sound/atmel_ac97c.txt new file mode 100644 index 00000000000..b151bd902ce --- /dev/null +++ b/Documentation/devicetree/bindings/sound/atmel_ac97c.txt @@ -0,0 +1,20 @@ +* Atmel AC97 controller + +Required properties: + - compatible: "atmel,at91sam9263-ac97c" + - reg: Address and length of the register set for the device + - interrupts: Should contain AC97 interrupt + - ac97-gpios: Please refer to soc-ac97link.txt, only ac97-reset is used +Optional properties: + - pinctrl-names, pinctrl-0: Please refer to pinctrl-bindings.txt + +Example: +sound@fffa0000 { + compatible = "atmel,at91sam9263-ac97c"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ac97>; + reg = <0xfffa0000 0x4000>; + interrupts = <18 IRQ_TYPE_LEVEL_HIGH 5>; + + ac97-gpios = <&pioB 0 0 &pioB 2 0 &pioC 29 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/sound/cdns,xtfpga-i2s.txt b/Documentation/devicetree/bindings/sound/cdns,xtfpga-i2s.txt new file mode 100644 index 00000000000..befd125d18b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cdns,xtfpga-i2s.txt @@ -0,0 +1,18 @@ +Bindings for I2S controller built into xtfpga Xtensa bitstreams. + +Required properties: +- compatible: shall be "cdns,xtfpga-i2s". +- reg: memory region (address and length) with device registers. +- interrupts: interrupt for the device. +- clocks: phandle to the clk used as master clock. I2S bus clock + is derived from it. + +Examples: + + i2s0: xtfpga-i2s@0d080000 { + #sound-dai-cells = <0>; + compatible = "cdns,xtfpga-i2s"; + reg = <0x0d080000 0x40>; + interrupts = <2 1>; + clocks = <&cdce706 4>; + }; diff --git a/Documentation/devicetree/bindings/sound/designware-i2s.txt b/Documentation/devicetree/bindings/sound/designware-i2s.txt new file mode 100644 index 00000000000..7bb54247f8e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/designware-i2s.txt @@ -0,0 +1,31 @@ +DesignWare I2S controller + +Required properties: + - compatible : Must be "snps,designware-i2s" + - reg : Must contain the I2S core's registers location and length + - clocks : Pairs of phandle and specifier referencing the controller's + clocks. The controller expects one clock: the clock used as the sampling + rate reference clock sample. + - clock-names : "i2sclk" for the sample rate reference clock. + - dmas: Pairs of phandle and specifier for the DMA channels that are used by + the core. The core expects one or two dma channels: one for transmit and + one for receive. + - dma-names : "tx" for the transmit channel, "rx" for the receive channel. + +For more details on the 'dma', 'dma-names', 'clock' and 'clock-names' +properties please check: + * resource-names.txt + * clock/clock-bindings.txt + * dma/dma.txt + +Example: + + soc_i2s: i2s@7ff90000 { + compatible = "snps,designware-i2s"; + reg = <0x0 0x7ff90000 0x0 0x1000>; + clocks = <&scpi_i2sclk 0>; + clock-names = "i2sclk"; + #sound-dai-cells = <0>; + dmas = <&dma0 5>; + dma-names = "tx"; + }; diff --git a/Documentation/devicetree/bindings/sound/ingenic,jz4740-i2s.txt b/Documentation/devicetree/bindings/sound/ingenic,jz4740-i2s.txt new file mode 100644 index 00000000000..b41433386e2 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ingenic,jz4740-i2s.txt @@ -0,0 +1,23 @@ +Ingenic JZ4740 I2S controller + +Required properties: +- compatible : "ingenic,jz4740-i2s" +- reg : I2S registers location and length +- clocks : AIC and I2S PLL clock specifiers. +- clock-names: "aic" and "i2s" +- dmas: DMA controller phandle and DMA request line for I2S Tx and Rx channels +- dma-names: Must be "tx" and "rx" + +Example: + +i2s: i2s@10020000 { + compatible = "ingenic,jz4740-i2s"; + reg = <0x10020000 0x94>; + + clocks = <&cgu JZ4740_CLK_AIC>, <&cgu JZ4740_CLK_I2SPLL>; + clock-names = "aic", "i2s"; + + dmas = <&dma 2>, <&dma 3>; + dma-names = "tx", "rx"; + +}; diff --git a/Documentation/devicetree/bindings/sound/max98357a.txt b/Documentation/devicetree/bindings/sound/max98357a.txt new file mode 100644 index 00000000000..a7a149a236e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max98357a.txt @@ -0,0 +1,14 @@ +Maxim MAX98357A audio DAC + +This node models the Maxim MAX98357A DAC. + +Required properties: +- compatible : "maxim,max98357a" +- sdmode-gpios : GPIO specifier for the GPIO -> DAC SDMODE pin + +Example: + +max98357a { + compatible = "maxim,max98357a"; + sdmode-gpios = <&qcom_pinmux 25 0>; +}; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.txt new file mode 100644 index 00000000000..a4589cda214 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.txt @@ -0,0 +1,67 @@ +NVIDIA Tegra audio complex, with RT5677 CODEC + +Required properties: +- compatible : "nvidia,tegra-audio-rt5677" +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: + - pll_a + - pll_a_out0 + - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the RT5677's pins (as documented in its binding), and the jacks + on the board: + + * Headphone + * Speaker + * Headset Mic + * Internal Mic 1 + * Internal Mic 2 + +- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's + connected to the CODEC. +- nvidia,audio-codec : The phandle of the RT5677 audio codec. This binding + assumes that AIF1 on the CODEC is connected to Tegra. + +Optional properties: +- nvidia,hp-det-gpios : The GPIO that detects headphones are plugged in +- nvidia,hp-en-gpios : The GPIO that enables headphone amplifier +- nvidia,mic-present-gpios: The GPIO that mic jack is plugged in +- nvidia,dmic-clk-en-gpios : The GPIO that gates DMIC clock signal + +Example: + +sound { + compatible = "nvidia,tegra-audio-rt5677-ryu", + "nvidia,tegra-audio-rt5677"; + nvidia,model = "NVIDIA Tegra Ryu"; + + nvidia,audio-routing = + "Headphone", "LOUT2", + "Headphone", "LOUT1", + "Headset Mic", "MICBIAS1", + "IN1P", "Headset Mic", + "IN1N", "Headset Mic", + "DMIC L1", "Internal Mic 1", + "DMIC R1", "Internal Mic 1", + "DMIC L2", "Internal Mic 2", + "DMIC R2", "Internal Mic 2", + "Speaker", "PDM1L", + "Speaker", "PDM1R"; + + nvidia,i2s-controller = <&tegra_i2s1>; + nvidia,audio-codec = <&rt5677>; + + nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>; + nvidia,mic-present-gpios = <&gpio TEGRA_GPIO(O, 5) GPIO_ACTIVE_LOW>; + nvidia,hp-en-gpios = <&rt5677 1 GPIO_ACTIVE_HIGH>; + nvidia,dmic-clk-en-gpios = <&rt5677 2 GPIO_ACTIVE_HIGH>; + + clocks = <&tegra_car TEGRA124_CLK_PLL_A>, + <&tegra_car TEGRA124_CLK_PLL_A_OUT0>, + <&tegra_car TEGRA124_CLK_EXTERN1>; + clock-names = "pll_a", "pll_a_out0", "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra30-ahub.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra30-ahub.txt index 946e2ac4609..0e9a1895d7f 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra30-ahub.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra30-ahub.txt @@ -1,7 +1,10 @@ NVIDIA Tegra30 AHUB (Audio Hub) Required properties: -- compatible : "nvidia,tegra30-ahub", "nvidia,tegra114-ahub", etc. +- compatible : For Tegra30, must contain "nvidia,tegra30-ahub". For Tegra114, + must contain "nvidia,tegra114-ahub". For Tegra124, must contain + "nvidia,tegra124-ahub". Otherwise, must contain "nvidia,<chip>-ahub", + plus at least one of the above, where <chip> is tegra132. - reg : Should contain the register physical address and length for each of the AHUB's register blocks. - Tegra30 requires 2 entries, for the APBIF and AHUB/AUDIO register blocks. diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt index b4730c2822b..13e2ef49672 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt @@ -1,7 +1,9 @@ NVIDIA Tegra30 HDA controller Required properties: -- compatible : "nvidia,tegra30-hda" +- compatible : For Tegra30, must contain "nvidia,tegra30-hda". Otherwise, + must contain '"nvidia,<chip>-hda", "nvidia,tegra30-hda"', where <chip> is + tegra114, tegra124, or tegra132. - reg : Should contain the HDA registers location and length. - interrupts : The interrupt from the HDA controller. - clocks : Must contain an entry for each required entry in clock-names. diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra30-i2s.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra30-i2s.txt index 0c113ffe381..38caa936f6f 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra30-i2s.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra30-i2s.txt @@ -1,7 +1,10 @@ NVIDIA Tegra30 I2S controller Required properties: -- compatible : "nvidia,tegra30-i2s" +- compatible : For Tegra30, must contain "nvidia,tegra30-i2s". For Tegra124, + must contain "nvidia,tegra124-i2s". Otherwise, must contain + "nvidia,<chip>-i2s" plus at least one of the above, where <chip> is + tegra114 or tegra132. - reg : Should contain I2S registers location and length - clocks : Must contain one entry, for the module clock. See ../clocks/clock-bindings.txt for details. diff --git a/Documentation/devicetree/bindings/sound/pcm512x.txt b/Documentation/devicetree/bindings/sound/pcm512x.txt index faff75e6457..3aae3b41bd8 100644 --- a/Documentation/devicetree/bindings/sound/pcm512x.txt +++ b/Documentation/devicetree/bindings/sound/pcm512x.txt @@ -5,7 +5,8 @@ on the board). Required properties: - - compatible : One of "ti,pcm5121" or "ti,pcm5122" + - compatible : One of "ti,pcm5121", "ti,pcm5122", "ti,pcm5141" or + "ti,pcm5142" - reg : the I2C address of the device for I2C, the chip select number for SPI. @@ -16,9 +17,16 @@ Required properties: Optional properties: - clocks : A clock specifier for the clock connected as SCLK. If this - is absent the device will be configured to clock from BCLK. + is absent the device will be configured to clock from BCLK. If pll-in + and pll-out are specified in addition to a clock, the device is + configured to accept clock input on a specified gpio pin. -Example: + - pll-in, pll-out : gpio pins used to connect the pll using <1> + through <6>. The device will be configured for clock input on the + given pll-in pin and PLL output on the given pll-out pin. An + external connection from the pll-out pin to the SCLK pin is assumed. + +Examples: pcm5122: pcm5122@4c { compatible = "ti,pcm5122"; @@ -28,3 +36,17 @@ Example: DVDD-supply = <®_1v8>; CPVDD-supply = <®_3v3>; }; + + + pcm5142: pcm5142@4c { + compatible = "ti,pcm5142"; + reg = <0x4c>; + + AVDD-supply = <®_3v3_analog>; + DVDD-supply = <®_1v8>; + CPVDD-supply = <®_3v3>; + + clocks = <&sck>; + pll-in = <3>; + pll-out = <6>; + }; diff --git a/Documentation/devicetree/bindings/sound/samsung-i2s.txt b/Documentation/devicetree/bindings/sound/samsung-i2s.txt index d188296bb6e..09e0e18591a 100644 --- a/Documentation/devicetree/bindings/sound/samsung-i2s.txt +++ b/Documentation/devicetree/bindings/sound/samsung-i2s.txt @@ -33,6 +33,25 @@ Required SoC Specific Properties: "iis" is the i2s bus clock and i2s_opclk0, i2s_opclk1 are sources of the root clk. i2s0 has internal mux to select the source of root clk and i2s1 and i2s2 doesn't have any such mux. +- #clock-cells: should be 1, this property must be present if the I2S device + is a clock provider in terms of the common clock bindings, described in + ../clock/clock-bindings.txt. +- clock-output-names: from the common clock bindings, names of the CDCLK + I2S output clocks, suggested values are "i2s_cdclk0", "i2s_cdclk1", + "i2s_cdclk3" for the I2S0, I2S1, I2S2 devices recpectively. + +There are following clocks available at the I2S device nodes: + CLK_I2S_CDCLK - the CDCLK (CODECLKO) gate clock, + CLK_I2S_RCLK_PSR - the RCLK prescaler divider clock (corresponding to the + IISPSR register), + CLK_I2S_RCLK_SRC - the RCLKSRC mux clock (corresponding to RCLKSRC bit in + IISMOD register). + +Refer to the SoC datasheet for availability of the above clocks. +The CLK_I2S_RCLK_PSR and CLK_I2S_RCLK_SRC clocks are usually only available +in the IIS Multi Audio Interface (I2S0). +Note: Old DTs may not have the #clock-cells, clock-output-names properties +and then not use the I2S node as a clock supplier. Optional SoC Specific Properties: @@ -41,6 +60,7 @@ Optional SoC Specific Properties: - pinctrl-0: Should specify pin control groups used for this controller. - pinctrl-names: Should contain only one value - "default". + Example: i2s0: i2s@03830000 { @@ -54,6 +74,8 @@ i2s0: i2s@03830000 { <&clock_audss EXYNOS_I2S_BUS>, <&clock_audss EXYNOS_SCLK_I2S>; clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; + #clock-cells; + clock-output-names = "i2s_cdclk0"; samsung,idma-addr = <0x03000000>; pinctrl-names = "default"; pinctrl-0 = <&i2s0_bus>; diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index c3cba600bf1..73bf314f724 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -75,6 +75,11 @@ Optional CPU/CODEC subnodes properties: it can be specified via "clocks" if system has clock node (= common clock), or "system-clock-frequency" (if system doens't support common clock) + If a clock is specified, it is + enabled with clk_prepare_enable() + in dai startup() and disabled with + clk_disable_unprepare() in dai + shutdown(). Example 1 - single DAI link: diff --git a/Documentation/devicetree/bindings/sound/st,sta32x.txt b/Documentation/devicetree/bindings/sound/st,sta32x.txt new file mode 100644 index 00000000000..255de3ae5b2 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/st,sta32x.txt @@ -0,0 +1,92 @@ +STA32X audio CODEC + +The driver for this device only supports I2C. + +Required properties: + + - compatible: "st,sta32x" + - reg: the I2C address of the device for I2C + - reset-gpios: a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - power-down-gpios: a GPIO spec for the power down pin. If specified, + it will be deasserted before communication to the codec + starts. + + - Vdda-supply: regulator spec, providing 3.3V + - Vdd3-supply: regulator spec, providing 3.3V + - Vcc-supply: regulator spec, providing 5V - 26V + +Optional properties: + + - st,output-conf: number, Selects the output configuration: + 0: 2-channel (full-bridge) power, 2-channel data-out + 1: 2 (half-bridge). 1 (full-bridge) on-board power + 2: 2 Channel (Full-Bridge) Power, 1 Channel FFX + 3: 1 Channel Mono-Parallel + If parameter is missing, mode 0 will be enabled. + This property has to be specified as '/bits/ 8' value. + + - st,ch1-output-mapping: Channel 1 output mapping + - st,ch2-output-mapping: Channel 2 output mapping + - st,ch3-output-mapping: Channel 3 output mapping + 0: Channel 1 + 1: Channel 2 + 2: Channel 3 + If parameter is missing, channel 1 is chosen. + This properties have to be specified as '/bits/ 8' values. + + - st,thermal-warning-recover: + If present, thermal warning recovery is enabled. + + - st,thermal-warning-adjustment: + If present, thermal warning adjustment is enabled. + + - st,fault-detect-recovery: + If present, then fault recovery will be enabled. + + - st,drop-compensation-ns: number + Only required for "st,ffx-power-output-mode" == + "variable-drop-compensation". + Specifies the drop compensation in nanoseconds. + The value must be in the range of 0..300, and only + multiples of 20 are allowed. Default is 140ns. + + - st,max-power-use-mpcc: + If present, then MPCC bits are used for MPC coefficients, + otherwise standard MPC coefficients are used. + + - st,max-power-corr: + If present, power bridge correction for THD reduction near maximum + power output is enabled. + + - st,am-reduction-mode: + If present, FFX mode runs in AM reduction mode, otherwise normal + FFX mode is used. + + - st,odd-pwm-speed-mode: + If present, PWM speed mode run on odd speed mode (341.3 kHz) on all + channels. If not present, normal PWM spped mode (384 kHz) will be used. + + - st,invalid-input-detect-mute: + If present, automatic invalid input detect mute is enabled. + +Example: + +codec: sta32x@38 { + compatible = "st,sta32x"; + reg = <0x1c>; + reset-gpios = <&gpio1 19 0>; + power-down-gpios = <&gpio1 16 0>; + st,output-conf = /bits/ 8 <0x3>; // set output to 2-channel + // (full-bridge) power, + // 2-channel data-out + st,ch1-output-mapping = /bits/ 8 <0>; // set channel 1 output ch 1 + st,ch2-output-mapping = /bits/ 8 <0>; // set channel 2 output ch 1 + st,ch3-output-mapping = /bits/ 8 <0>; // set channel 3 output ch 1 + st,max-power-correction; // enables power bridge + // correction for THD reduction + // near maximum power output + st,invalid-input-detect-mute; // mute if no valid digital + // audio signal is provided. +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt index 5e6040c2c2e..47a213c411c 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt @@ -9,6 +9,7 @@ Required properties: "ti,tlv320aic33" - TLV320AIC33 "ti,tlv320aic3007" - TLV320AIC3007 "ti,tlv320aic3106" - TLV320AIC3106 + "ti,tlv320aic3104" - TLV320AIC3104 - reg - <int> - I2C slave address @@ -18,6 +19,7 @@ Optional properties: - gpio-reset - gpio pin number used for codec reset - ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality + - Not supported on tlv320aic3104 - ai3x-micbias-vg - MicBias Voltage required. 1 - MICBIAS output is powered to 2.0V, 2 - MICBIAS output is powered to 2.5V, @@ -36,7 +38,13 @@ CODEC output pins: * HPLCOM * HPRCOM -CODEC input pins: +CODEC input pins for TLV320AIC3104: + * MIC2L + * MIC2R + * LINE1L + * LINE1R + +CODEC input pins for other compatible codecs: * MIC3L * MIC3R * LINE1L diff --git a/Documentation/devicetree/bindings/sound/ts3a227e.txt b/Documentation/devicetree/bindings/sound/ts3a227e.txt index e8bf23eb180..a836881d960 100644 --- a/Documentation/devicetree/bindings/sound/ts3a227e.txt +++ b/Documentation/devicetree/bindings/sound/ts3a227e.txt @@ -13,6 +13,11 @@ Required properties: - interrupt-parent: The parent interrupt controller - interrupts: Interrupt number for /INT pin from the 227e +Optional properies: + - ti,micbias: Intended MICBIAS voltage (datasheet section 9.6.7). + Select 0/1/2/3/4/5/6/7 to specify MACBIAS voltage + 2.1V/2.2V/2.3V/2.4V/2.5V/2.6V/2.7V/2.8V + Default value is "1" (2.2V). Examples: diff --git a/Documentation/devicetree/bindings/sound/wm8904.txt b/Documentation/devicetree/bindings/sound/wm8904.txt index e99f4097c83..66bf261423b 100644 --- a/Documentation/devicetree/bindings/sound/wm8904.txt +++ b/Documentation/devicetree/bindings/sound/wm8904.txt @@ -3,7 +3,7 @@ WM8904 audio CODEC This device supports I2C only. Required properties: - - compatible: "wlf,wm8904" + - compatible: "wlf,wm8904" or "wlf,wm8912" - reg: the I2C address of the device. - clock-names: "mclk" - clocks: reference to |