diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb')
11 files changed, 166 insertions, 11 deletions
diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt new file mode 100644 index 00000000000..f2899b55093 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt @@ -0,0 +1,17 @@ +Qualcomm CI13xxx (Chipidea) USB controllers + +Required properties: +- compatible: should contain "qcom,ci-hdrc" +- reg: offset and length of the register set in the memory map +- interrupts: interrupt-specifier for the controller interrupt. +- usb-phy: phandle for the PHY device +- dr_mode: Should be "peripheral" + +Examples: + gadget@f9a55000 { + compatible = "qcom,ci-hdrc"; + reg = <0xf9a55000 0x400>; + dr_mode = "peripheral"; + interrupts = <0 134 0>; + usb-phy = <&usbphy0>; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index b8b6871f116..467ddd15d40 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -13,7 +13,7 @@ Refer to clk/clock-bindings.txt for generic clock consumer properties Optional properties: - phys: phy provider specifier -- phy-names: shall be "device" +- phy-names: shall be "usb2-phy" Refer to phy/phy-bindings.txt for generic phy consumer properties Example: diff --git a/Documentation/devicetree/bindings/usb/ehci-orion.txt b/Documentation/devicetree/bindings/usb/ehci-orion.txt index 6bc09ec14c4..17c3bc858b8 100644 --- a/Documentation/devicetree/bindings/usb/ehci-orion.txt +++ b/Documentation/devicetree/bindings/usb/ehci-orion.txt @@ -6,6 +6,11 @@ Required properties: region. - interrupts: The EHCI interrupt +Optional properties: +- clocks: reference to the clock +- phys: reference to the USB PHY +- phy-names: name of the USB PHY, should be "usb" + Example: ehci@50000 { diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt index d967ba16de6..a3b5990d0f2 100644 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -12,6 +12,13 @@ Required properties: - interrupts: interrupt number to the cpu. - clocks: from common clock binding: handle to usb clock. - clock-names: from common clock binding: Shall be "usbhost". + - port: if in the SoC there are EHCI phys, they should be listed here. + One phy per port. Each port should have following entries: + - reg: port number on EHCI controller, e.g + On Exynos5250, port 0 is USB2.0 otg phy + port 1 is HSIC phy0 + port 2 is HSIC phy1 + - phys: from the *Generic PHY* bindings; specifying phy used by port. Optional properties: - samsung,vbus-gpio: if present, specifies the GPIO that @@ -27,6 +34,14 @@ Example: clocks = <&clock 285>; clock-names = "usbhost"; + + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + phys = <&usb2phy 1>; + status = "disabled"; + }; }; OHCI @@ -38,6 +53,13 @@ Required properties: - interrupts: interrupt number to the cpu. - clocks: from common clock binding: handle to usb clock. - clock-names: from common clock binding: Shall be "usbhost". + - port: if in the SoC there are OHCI phys, they should be listed here. + One phy per port. Each port should have following entries: + - reg: port number on OHCI controller, e.g + On Exynos5250, port 0 is USB2.0 otg phy + port 1 is HSIC phy0 + port 2 is HSIC phy1 + - phys: from the *Generic PHY* bindings, specifying phy used by port. Example: usb@12120000 { @@ -47,6 +69,15 @@ Example: clocks = <&clock 285>; clock-names = "usbhost"; + + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + phys = <&usb2phy 1>; + status = "disabled"; + }; + }; DWC3 diff --git a/Documentation/devicetree/bindings/usb/gr-udc.txt b/Documentation/devicetree/bindings/usb/gr-udc.txt index 0c5118f7a91..e9445224fab 100644 --- a/Documentation/devicetree/bindings/usb/gr-udc.txt +++ b/Documentation/devicetree/bindings/usb/gr-udc.txt @@ -12,17 +12,23 @@ Required properties: - reg : Address and length of the register set for the device -- interrupts : Interrupt numbers for this device +- interrupts : Interrupt numbers for this device. Either one interrupt number + for all interrupts, or one for status related interrupts, one for IN + endpoint related interrupts and one for OUT endpoint related interrupts. Optional properties: -- epobufsizes : An array of buffer sizes for OUT endpoints. If the property is - not present, or for endpoints outside of the array, 1024 is assumed by - the driver. - -- epibufsizes : An array of buffer sizes for IN endpoints. If the property is - not present, or for endpoints outside of the array, 1024 is assumed by - the driver. +- epobufsizes : Array of buffer sizes for OUT endpoints when they differ + from the default size of 1024. The array is indexed by the OUT endpoint + number. If the property is present it typically contains one entry for + each OUT endpoint of the core. Fewer entries overrides the default sizes + only for as many endpoints as the array contains. + +- epibufsizes : Array of buffer sizes for IN endpoints when they differ + from the default size of 1024. The array is indexed by the IN endpoint + number. If the property is present it typically contains one entry for + each IN endpoint of the core. Fewer entries overrides the default sizes + only for as many endpoints as the array contains. For further information look in the documentation for the GLIB IP core library: http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt index 5ea26c631e3..2826f2af503 100644 --- a/Documentation/devicetree/bindings/usb/msm-hsusb.txt +++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt @@ -15,3 +15,81 @@ Example EHCI controller device node: usb-phy = <&usb_otg>; }; +USB PHY with optional OTG: + +Required properties: +- compatible: Should contain: + "qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY + "qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY + +- regs: Offset and length of the register set in the memory map +- interrupts: interrupt-specifier for the OTG interrupt. + +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "phy" USB PHY reference clock + "core" Protocol engine clock + "iface" Interface bus clock + "alt_core" Protocol engine clock for targets with asynchronous + reset methodology. (optional) + +- vdccx-supply: phandle to the regulator for the vdd supply for + digital circuit operation. +- v1p8-supply: phandle to the regulator for the 1.8V supply +- v3p3-supply: phandle to the regulator for the 3.3V supply + +- resets: A list of phandle + reset-specifier pairs for the + resets listed in reset-names +- reset-names: Should contain the following: + "phy" USB PHY controller reset + "link" USB LINK controller reset + +- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of + 1 - PHY control + 2 - PMIC control + +Optional properties: +- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" + +- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device + Mode Eye Diagram test. Start address at which these values will be + written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as + "do not overwrite default value at this address". + For example: qcom,phy-init-sequence = < -1 0x63 >; + Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1. + +- qcom,phy-num: Select number of pyco-phy to use, can be one of + 0 - PHY one, default + 1 - Second PHY + Some platforms may have configuration to allow USB + controller work with any of the two HSPHYs present. + +- qcom,vdd-levels: This property must be a list of three integer values + (no, min, max) where each value represents either a voltage + in microvolts or a value corresponding to voltage corner. + +Example HSUSB OTG controller device node: + + usb@f9a55000 { + compatible = "qcom,usb-otg-snps"; + reg = <0xf9a55000 0x400>; + interrupts = <0 134 0>; + dr_mode = "peripheral"; + + clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>, + <&gcc GCC_USB_HS_AHB_CLK>; + + clock-names = "phy", "core", "iface"; + + vddcx-supply = <&pm8841_s2_corner>; + v1p8-supply = <&pm8941_l6>; + v3p3-supply = <&pm8941_l24>; + + resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>; + reset-names = "phy", "link"; + + qcom,otg-control = <1>; + qcom,phy-init-sequence = < -1 0x63 >; + qcom,vdd-levels = <1 5 7>; + }; diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 38b2faec419..38d9bb8507c 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -44,7 +44,9 @@ Board specific device node entry }; OMAP DWC3 GLUE - - compatible : Should be "ti,dwc3" + - compatible : Should be + * "ti,dwc3" for OMAP5 and DRA7 + * "ti,am437x-dwc3" for AM437x - ti,hwmods : Should be "usb_otg_ss" - reg : Address and length of the register set for the device. - interrupts : The irq number of this device that is used to interrupt the diff --git a/Documentation/devicetree/bindings/usb/usb-ehci.txt b/Documentation/devicetree/bindings/usb/usb-ehci.txt index ff151ec084c..43c1a4e0676 100644 --- a/Documentation/devicetree/bindings/usb/usb-ehci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ehci.txt @@ -15,6 +15,7 @@ Optional properties: - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair - phy-names : "usb" + - resets : phandle + reset specifier pair Example (Sequoia 440EPx): ehci@e0000300 { diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt index 45f67d91e88..b968a1aea99 100644 --- a/Documentation/devicetree/bindings/usb/usb-ohci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -12,6 +12,7 @@ Optional properties: - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair - phy-names : "usb" +- resets : phandle + reset specifier pair Example: diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 90f8f607d12..5a79377c6a9 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -1,11 +1,17 @@ USB xHCI controllers Required properties: - - compatible: should be "generic-xhci" (deprecated: "xhci-platform"). + - compatible: should be one of "generic-xhci", + "marvell,armada-375-xhci", "marvell,armada-380-xhci", + "renesas,xhci-r8a7790", "renesas,xhci-r8a7791" (deprecated: + "xhci-platform"). - reg: should contain address and length of the standard XHCI register set for the device. - interrupts: one XHCI interrupt should be described here. +Optional property: + - clocks: reference to a clock + Example: usb@f0931000 { compatible = "generic-xhci"; diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt index a018da4a7ad..221ac0dbc67 100644 --- a/Documentation/devicetree/bindings/usb/usb3503.txt +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -15,6 +15,14 @@ Optional properties: - reset-gpios: Should specify GPIO for reset. - initial-mode: Should specify initial mode. (1 for HUB mode, 2 for STANDBY mode) +- refclk: Clock used for driving REFCLK signal (optional, if not provided + the driver assumes that clock signal is always available, its + rate is specified by REF_SEL pins and a value from the primary + reference clock frequencies table is used) +- refclk-frequency: Frequency of the REFCLK signal as defined by REF_SEL + pins (optional, if not provided, driver will not set rate of the + REFCLK signal and assume that a value from the primary reference + clock frequencies table is used) Examples: usb3503@08 { |