diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
85 files changed, 2541 insertions, 102 deletions
diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt b/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt index 926b4d6aae7..26799ef562d 100644 --- a/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt +++ b/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt @@ -1,20 +1,21 @@ Power Management Service Unit(PMSU) ----------------------------------- -Available on Marvell SOCs: Armada 370 and Armada XP +Available on Marvell SOCs: Armada 370, Armada 38x and Armada XP Required properties: -- compatible: "marvell,armada-370-xp-pmsu" +- compatible: should be one of: + - "marvell,armada-370-pmsu" for Armada 370 or Armada XP + - "marvell,armada-380-pmsu" for Armada 38x + - "marvell,armada-370-xp-pmsu" was used for Armada 370/XP but is now + deprecated and will be removed -- reg: Should contain PMSU registers location and length. First pair - for the per-CPU SW Reset Control registers, second pair for the - Power Management Service Unit. +- reg: Should contain PMSU registers location and length. Example: -armada-370-xp-pmsu@d0022000 { - compatible = "marvell,armada-370-xp-pmsu"; - reg = <0xd0022100 0x430>, - <0xd0020800 0x20>; +armada-370-xp-pmsu@22000 { + compatible = "marvell,armada-370-pmsu"; + reg = <0x22000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/arm/armada-cpu-reset.txt b/Documentation/devicetree/bindings/arm/armada-cpu-reset.txt new file mode 100644 index 00000000000..b63a7b6ab99 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armada-cpu-reset.txt @@ -0,0 +1,14 @@ +Marvell Armada CPU reset controller +=================================== + +Required properties: + +- compatible: Should be "marvell,armada-370-cpu-reset". + +- reg: should be register base and length as documented in the + datasheet for the CPU reset registers + +cpurst: cpurst@20800 { + compatible = "marvell,armada-370-cpu-reset"; + reg = <0x20800 0x20>; +}; diff --git a/Documentation/devicetree/bindings/arm/axxia.txt b/Documentation/devicetree/bindings/arm/axxia.txt new file mode 100644 index 00000000000..7b4ef9c0769 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/axxia.txt @@ -0,0 +1,12 @@ +Axxia AXM55xx device tree bindings + +Boards using the AXM55xx SoC need to have the following properties: + +Required root node property: + + - compatible = "lsi,axm5516" + +Boards: + + LSI AXM5516 Validation board (Amarillo) + compatible = "lsi,axm5516-amarillo", "lsi,axm5516" diff --git a/Documentation/devicetree/bindings/arm/coherency-fabric.txt b/Documentation/devicetree/bindings/arm/coherency-fabric.txt index 17d8cd10755..8dd46617c88 100644 --- a/Documentation/devicetree/bindings/arm/coherency-fabric.txt +++ b/Documentation/devicetree/bindings/arm/coherency-fabric.txt @@ -1,16 +1,33 @@ Coherency fabric ---------------- -Available on Marvell SOCs: Armada 370 and Armada XP +Available on Marvell SOCs: Armada 370, Armada 375, Armada 38x and Armada XP Required properties: -- compatible: "marvell,coherency-fabric" +- compatible: the possible values are: + + * "marvell,coherency-fabric", to be used for the coherency fabric of + the Armada 370 and Armada XP. + + * "marvell,armada-375-coherency-fabric", for the Armada 375 coherency + fabric. + + * "marvell,armada-380-coherency-fabric", for the Armada 38x coherency + fabric. - reg: Should contain coherency fabric registers location and - length. First pair for the coherency fabric registers, second pair - for the per-CPU fabric registers registers. + length. + + * For "marvell,coherency-fabric", the first pair for the coherency + fabric registers, second pair for the per-CPU fabric registers. -Example: + * For "marvell,armada-375-coherency-fabric", only one pair is needed + for the per-CPU fabric registers. + + * For "marvell,armada-380-coherency-fabric", only one pair is needed + for the per-CPU fabric registers. + +Examples: coherency-fabric@d0020200 { compatible = "marvell,coherency-fabric"; @@ -19,3 +36,8 @@ coherency-fabric@d0020200 { }; +coherency-fabric@21810 { + compatible = "marvell,armada-375-coherency-fabric"; + reg = <0x21810 0x1c>; +}; + diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 333f4aea302..1fe72a0778c 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -178,13 +178,19 @@ nodes to be present and contain the properties described below. Usage and definition depend on ARM architecture version. # On ARM v8 64-bit this property is required and must be one of: - "spin-table" "psci" + "spin-table" # On ARM 32-bit systems this property is optional and can be one of: + "allwinner,sun6i-a31" + "arm,psci" + "marvell,armada-375-smp" + "marvell,armada-380-smp" + "marvell,armada-xp-smp" "qcom,gcc-msm8660" "qcom,kpss-acc-v1" "qcom,kpss-acc-v2" + "rockchip,rk3066-smp" - cpu-release-addr Usage: required for systems that have an "enable-method" diff --git a/Documentation/devicetree/bindings/arm/exynos/smp-sysram.txt b/Documentation/devicetree/bindings/arm/exynos/smp-sysram.txt new file mode 100644 index 00000000000..4a0a4f70a0c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/exynos/smp-sysram.txt @@ -0,0 +1,38 @@ +Samsung Exynos SYSRAM for SMP bringup: +------------------------------------ + +Samsung SMP-capable Exynos SoCs use part of the SYSRAM for the bringup +of the secondary cores. Once the core gets powered up it executes the +code that is residing at some specific location of the SYSRAM. + +Therefore reserved section sub-nodes have to be added to the mmio-sram +declaration. These nodes are of two types depending upon secure or +non-secure execution environment. + +Required sub-node properties: +- compatible : depending upon boot mode, should be + "samsung,exynos4210-sysram" : for Secure SYSRAM + "samsung,exynos4210-sysram-ns" : for Non-secure SYSRAM + +The rest of the properties should follow the generic mmio-sram discription +found in ../../misc/sysram.txt + +Example: + + sysram@02020000 { + compatible = "mmio-sram"; + reg = <0x02020000 0x54000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x02020000 0x54000>; + + smp-sysram@0 { + compatible = "samsung,exynos4210-sysram"; + reg = <0x0 0x1000>; + }; + + smp-sysram@53000 { + compatible = "samsung,exynos4210-sysram-ns"; + reg = <0x53000 0x1000>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/marvell,berlin.txt b/Documentation/devicetree/bindings/arm/marvell,berlin.txt index 737afa5f814..94013a9a876 100644 --- a/Documentation/devicetree/bindings/arm/marvell,berlin.txt +++ b/Documentation/devicetree/bindings/arm/marvell,berlin.txt @@ -12,6 +12,7 @@ SoC and board used. Currently known SoC compatibles are: "marvell,berlin2" for Marvell Armada 1500 (BG2, 88DE3100), "marvell,berlin2cd" for Marvell Armada 1500-mini (BG2CD, 88DE3005) "marvell,berlin2ct" for Marvell Armada ? (BG2CT, 88DE????) + "marvell,berlin2q" for Marvell Armada 1500-pro (BG2Q, 88DE3114) "marvell,berlin3" for Marvell Armada ? (BG3, 88DE????) * Example: @@ -22,3 +23,104 @@ SoC and board used. Currently known SoC compatibles are: ... } + +* Marvell Berlin2 chip control binding + +Marvell Berlin SoCs have a chip control register set providing several +individual registers dealing with pinmux, padmux, clock, reset, and secondary +CPU boot address. Unfortunately, the individual registers are spread among the +chip control registers, so there should be a single DT node only providing the +different functions which are described below. + +Required properties: +- compatible: shall be one of + "marvell,berlin2-chip-ctrl" for BG2 + "marvell,berlin2cd-chip-ctrl" for BG2CD + "marvell,berlin2q-chip-ctrl" for BG2Q +- reg: address and length of following register sets for + BG2/BG2CD: chip control register set + BG2Q: chip control register set and cpu pll registers + +* Marvell Berlin2 system control binding + +Marvell Berlin SoCs have a system control register set providing several +individual registers dealing with pinmux, padmux, and reset. + +Required properties: +- compatible: should be one of + "marvell,berlin2-system-ctrl" for BG2 + "marvell,berlin2cd-system-ctrl" for BG2CD + "marvell,berlin2q-system-ctrl" for BG2Q +- reg: address and length of the system control register set + +* Clock provider binding + +As clock related registers are spread among the chip control registers, the +chip control node also provides the clocks. Marvell Berlin2 (BG2, BG2CD, BG2Q) +SoCs share the same IP for PLLs and clocks, with some minor differences in +features and register layout. + +Required properties: +- #clock-cells: shall be set to 1 +- clocks: clock specifiers referencing the core clock input clocks +- clock-names: array of strings describing the input clock specifiers above. + Allowed clock-names for the reference clocks are + "refclk" for the SoCs osciallator input on all SoCs, + and SoC-specific input clocks for + BG2/BG2CD: "video_ext0" for the external video clock input + +Clocks provided by core clocks shall be referenced by a clock specifier +indexing one of the provided clocks. Refer to dt-bindings/clock/berlin<soc>.h +for the corresponding index mapping. + +* Pin controller binding + +Pin control registers are part of both register sets, chip control and system +control. The pins controlled are organized in groups, so no actual pin +information is needed. + +A pin-controller node should contain subnodes representing the pin group +configurations, one per function. Each subnode has the group name and the muxing +function used. + +Be aware the Marvell Berlin datasheets use the keyword 'mode' for what is called +a 'function' in the pin-controller subsystem. + +Required subnode-properties: +- groups: a list of strings describing the group names. +- function: a string describing the function used to mux the groups. + +Example: + +chip: chip-control@ea0000 { + compatible = "marvell,berlin2-chip-ctrl"; + #clock-cells = <1>; + reg = <0xea0000 0x400>; + clocks = <&refclk>, <&externaldev 0>; + clock-names = "refclk", "video_ext0"; + + spi1_pmux: spi1-pmux { + groups = "G0"; + function = "spi1"; + }; +}; + +sysctrl: system-controller@d000 { + compatible = "marvell,berlin2-system-ctrl"; + reg = <0xd000 0x100>; + + uart0_pmux: uart0-pmux { + groups = "GSM4"; + function = "uart0"; + }; + + uart1_pmux: uart1-pmux { + groups = "GSM5"; + function = "uart1"; + }; + + uart2_pmux: uart2-pmux { + groups = "GSM3"; + function = "uart2"; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt index c0105de55cb..974624ea68f 100644 --- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt +++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt @@ -6,6 +6,8 @@ provided by Arteris. Required properties: - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family Should be "ti,omap4-l3-noc" for OMAP4 family + Should be "ti,dra7-l3-noc" for DRA7 family + Should be "ti,am4372-l3-noc" for AM43 family - reg: Contains L3 register address range for each noc domain. - ti,hwmods: "l3_main_1", ... One hwmod for each noc domain. diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 36ede19a163..189baba40cd 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -80,7 +80,10 @@ SoCs: compatible = "ti,omap5432", "ti,omap5" - DRA742 - compatible = "ti,dra7xx", "ti,dra7" + compatible = "ti,dra742", "ti,dra74", "ti,dra7" + +- DRA722 + compatible = "ti,dra722", "ti,dra72", "ti,dra7" - AM4372 compatible = "ti,am4372", "ti,am43" @@ -102,6 +105,12 @@ Boards: - OMAP4 DuoVero with Parlor : Commercial expansion board with daughter board compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4"; +- OMAP4 VAR-STK-OM44 : Commercial dev kit with VAR-OM44CustomBoard and VAR-SOM-OM44 w/WLAN + compatible = "variscite,var-stk-om44", "variscite,var-som-om44", "ti,omap4460", "ti,omap4"; + +- OMAP4 VAR-DVK-OM44 : Commercial dev kit with VAR-OM44CustomBoard, VAR-SOM-OM44 w/WLAN and LCD touchscreen + compatible = "variscite,var-dvk-om44", "variscite,var-som-om44", "ti,omap4460", "ti,omap4"; + - OMAP3 EVM : Software Development Board for OMAP35x, AM/DM37x compatible = "ti,omap3-evm", "ti,omap3" @@ -120,5 +129,8 @@ Boards: - AM437x GP EVM compatible = "ti,am437x-gp-evm", "ti,am4372", "ti,am43" -- DRA7 EVM: Software Developement Board for DRA7XX - compatible = "ti,dra7-evm", "ti,dra7" +- DRA742 EVM: Software Developement Board for DRA742 + compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" + +- DRA722 EVM: Software Development Board for DRA722 + compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7" diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt new file mode 100644 index 00000000000..857f12636eb --- /dev/null +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -0,0 +1,10 @@ +Rockchip platforms device tree bindings +--------------------------------------- + +- bq Curie 2 tablet: + Required root node properties: + - compatible = "mundoreader,bq-curie2", "rockchip,rk3066a"; + +- Radxa Rock board: + Required root node properties: + - compatible = "radxa,rock", "rockchip,rk3188"; diff --git a/Documentation/devicetree/bindings/arm/samsung/pmu.txt b/Documentation/devicetree/bindings/arm/samsung/pmu.txt index f1f155255f2..2a4ab046a8a 100644 --- a/Documentation/devicetree/bindings/arm/samsung/pmu.txt +++ b/Documentation/devicetree/bindings/arm/samsung/pmu.txt @@ -2,6 +2,10 @@ SAMSUNG Exynos SoC series PMU Registers Properties: - compatible : should contain two values. First value must be one from following list: + - "samsung,exynos3250-pmu" - for Exynos3250 SoC, + - "samsung,exynos4210-pmu" - for Exynos4210 SoC, + - "samsung,exynos4212-pmu" - for Exynos4212 SoC, + - "samsung,exynos4412-pmu" - for Exynos4412 SoC, - "samsung,exynos5250-pmu" - for Exynos5250 SoC, - "samsung,exynos5420-pmu" - for Exynos5420 SoC. second value must be always "syscon". diff --git a/Documentation/devicetree/bindings/arm/samsung/sysreg.txt b/Documentation/devicetree/bindings/arm/samsung/sysreg.txt index 0ab3251a6ec..4fced6e9d5e 100644 --- a/Documentation/devicetree/bindings/arm/samsung/sysreg.txt +++ b/Documentation/devicetree/bindings/arm/samsung/sysreg.txt @@ -1,8 +1,10 @@ SAMSUNG S5P/Exynos SoC series System Registers (SYSREG) Properties: - - compatible : should contain "samsung,<chip name>-sysreg", "syscon"; - For Exynos4 SoC series it should be "samsung,exynos4-sysreg", "syscon"; + - compatible : should contain two values. First value must be one from following list: + - "samsung,exynos4-sysreg" - for Exynos4 based SoCs, + - "samsung,exynos5-sysreg" - for Exynos5 based SoCs. + second value must be always "syscon". - reg : offset and length of the register set. Example: @@ -10,3 +12,8 @@ Example: compatible = "samsung,exynos4-sysreg", "syscon"; reg = <0x10010000 0x400>; }; + + syscon@10050000 { + compatible = "samsung,exynos5-sysreg", "syscon"; + reg = <0x10050000 0x5000>; + }; diff --git a/Documentation/devicetree/bindings/arm/sti.txt b/Documentation/devicetree/bindings/arm/sti.txt new file mode 100644 index 00000000000..92f16c78bb6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/sti.txt @@ -0,0 +1,15 @@ +ST STi Platforms Device Tree Bindings +--------------------------------------- + +Boards with the ST STiH415 SoC shall have the following properties: +Required root node property: +compatible = "st,stih415"; + +Boards with the ST STiH416 SoC shall have the following properties: +Required root node property: +compatible = "st,stih416"; + +Boards with the ST STiH407 SoC shall have the following properties: +Required root node property: +compatible = "st,stih407"; + diff --git a/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt b/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt index 5580e9c4bd8..00318d083c9 100644 --- a/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt +++ b/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt @@ -8,6 +8,8 @@ interrupt generation, MMC and NOR Flash control etc. Required node properties: - compatible value : = "arm,vexpress,sysreg"; - reg : physical base address and the size of the registers window + +Deprecated properties, replaced by GPIO subnodes (see below): - gpio-controller : specifies that the node is a GPIO controller - #gpio-cells : size of the GPIO specifier, should be 2: - first cell is the pseudo-GPIO line number: @@ -16,35 +18,86 @@ Required node properties: 2 - NOR FLASH WPn - second cell can take standard GPIO flags (currently ignored). +Control registers providing pseudo-GPIO lines must be represented +by subnodes, each of them requiring the following properties: +- compatible value : one of + "arm,vexpress-sysreg,sys_led" + "arm,vexpress-sysreg,sys_mci" + "arm,vexpress-sysreg,sys_flash" +- gpio-controller : makes the node a GPIO controller +- #gpio-cells : size of the GPIO specifier, must be 2: + - first cell is the function number: + - for sys_led : 0..7 = LED 0..7 + - for sys_mci : 0 = MMC CARDIN, 1 = MMC WPROT + - for sys_flash : 0 = NOR FLASH WPn + - second cell can take standard GPIO flags (currently ignored). + Example: v2m_sysreg: sysreg@10000000 { compatible = "arm,vexpress-sysreg"; reg = <0x10000000 0x1000>; - gpio-controller; - #gpio-cells = <2>; + + v2m_led_gpios: sys_led@08 { + compatible = "arm,vexpress-sysreg,sys_led"; + gpio-controller; + #gpio-cells = <2>; + }; + + v2m_mmc_gpios: sys_mci@48 { + compatible = "arm,vexpress-sysreg,sys_mci"; + gpio-controller; + #gpio-cells = <2>; + }; + + v2m_flash_gpios: sys_flash@4c { + compatible = "arm,vexpress-sysreg,sys_flash"; + gpio-controller; + #gpio-cells = <2>; + }; }; This block also can also act a bridge to the platform's configuration bus via "system control" interface, addressing devices with site number, position in the board stack, config controller, function and device -numbers - see motherboard's TRM for more details. - -The node describing a config device must refer to the sysreg node via -"arm,vexpress,config-bridge" phandle (can be also defined in the node's -parent) and relies on the board topology properties - see main vexpress -node documentation for more details. It must also define the following -property: -- arm,vexpress-sysreg,func : must contain two cells: - - first cell defines function number (eg. 1 for clock generator, - 2 for voltage regulators etc.) - - device number (eg. osc 0, osc 1 etc.) +numbers - see motherboard's TRM for more details. All configuration +controller accessible via this interface must reference the sysreg +node via "arm,vexpress,config-bridge" phandle and define appropriate +topology properties - see main vexpress node documentation for more +details. Each child of such node describes one function and must +define the following properties: +- compatible value : must be one of (corresponding to the TRM): + "arm,vexpress-amp" + "arm,vexpress-dvimode" + "arm,vexpress-energy" + "arm,vexpress-muxfpga" + "arm,vexpress-osc" + "arm,vexpress-power" + "arm,vexpress-reboot" + "arm,vexpress-reset" + "arm,vexpress-scc" + "arm,vexpress-shutdown" + "arm,vexpress-temp" + "arm,vexpress-volt" +- arm,vexpress-sysreg,func : must contain a set of two cells long groups: + - first cell of each group defines the function number + (eg. 1 for clock generator, 2 for voltage regulators etc.) + - second cell of each group defines device number (eg. osc 0, + osc 1 etc.) + - some functions (eg. energy meter, with its 64 bit long counter) + are using more than one function/device number pair Example: mcc { + compatible = "arm,vexpress,config-bus"; arm,vexpress,config-bridge = <&v2m_sysreg>; osc@0 { compatible = "arm,vexpress-osc"; arm,vexpress-sysreg,func = <1 0>; }; + + energy@0 { + compatible = "arm,vexpress-energy"; + arm,vexpress-sysreg,func = <13 0>, <13 1>; + }; }; diff --git a/Documentation/devicetree/bindings/arm/vexpress.txt b/Documentation/devicetree/bindings/arm/vexpress.txt index ae49161e478..39844cd0bcc 100644 --- a/Documentation/devicetree/bindings/arm/vexpress.txt +++ b/Documentation/devicetree/bindings/arm/vexpress.txt @@ -80,12 +80,17 @@ but also control clock generators, voltage regulators, gather environmental data like temperature, power consumption etc. Even the video output switch (FPGA) is controlled that way. -Nodes describing devices controlled by this infrastructure should -point at the bridge device node: +The controllers are not mapped into normal memory address space +and must be accessed through bridges - other devices capable +of generating transactions on the configuration bus. + +The nodes describing configuration controllers must define +the following properties: +- compatible value: + compatible = "arm,vexpress,config-bus"; - bridge phandle: arm,vexpress,config-bridge = <phandle>; -This property can be also defined in a parent node (eg. for a DCC) -and is effective for all children. +and children describing available functions. Platform topology @@ -197,7 +202,7 @@ Example of a VE tile description (simplified) }; dcc { - compatible = "simple-bus"; + compatible = "arm,vexpress,config-bus"; arm,vexpress,config-bridge = <&v2m_sysreg>; osc@0 { diff --git a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt new file mode 100644 index 00000000000..e2d501d20c9 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt @@ -0,0 +1,30 @@ +Broadcom GISB bus Arbiter controller + +Required properties: + +- compatible: should be "brcm,gisb-arb" +- reg: specifies the base physical address and size of the registers +- interrupt-parent: specifies the phandle to the parent interrupt controller + this arbiter gets interrupt line from +- interrupts: specifies the two interrupts (timeout and TEA) to be used from + the parent interrupt controller + +Optional properties: + +- brcm,gisb-arb-master-mask: 32-bits wide bitmask used to specify which GISB + masters are valid at the system level +- brcm,gisb-arb-master-names: string list of the litteral name of the GISB + masters. Should match the number of bits set in brcm,gisb-master-mask and + the order in which they appear + +Example: + +gisb-arb@f0400000 { + compatible = "brcm,gisb-arb"; + reg = <0xf0400000 0x800>; + interrupts = <0>, <2>; + interrupt-parent = <&sun_l2_intc>; + + brcm,gisb-arb-master-mask = <0x7>; + brcm,gisb-arb-master-names = "bsp_0", "scpu_0", "cpu_0"; +}; diff --git a/Documentation/devicetree/bindings/clock/altr_socfpga.txt b/Documentation/devicetree/bindings/clock/altr_socfpga.txt index 5dfd145d3cc..f72e80e0dad 100644 --- a/Documentation/devicetree/bindings/clock/altr_socfpga.txt +++ b/Documentation/devicetree/bindings/clock/altr_socfpga.txt @@ -21,8 +21,8 @@ Optional properties: - fixed-divider : If clocks have a fixed divider value, use this property. - clk-gate : For "socfpga-gate-clk", clk-gate contains the gating register and the bit index. -- div-reg : For "socfpga-gate-clk", div-reg contains the divider register, bit shift, - and width. +- div-reg : For "socfpga-gate-clk" and "socfpga-periph-clock", div-reg contains + the divider register, bit shift, and width. - clk-phase : For the sdmmc_clk, contains the value of the clock phase that controls the SDMMC CIU clock. The first value is the clk_sample(smpsel), and the second value is the cclk_in_drv(drvsel). The clk-phase is used to enable the correct diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index cd5e2391288..b3d544ca522 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -6,6 +6,16 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be one of the following: + "atmel,at91sam9x5-sckc": + at91 SCKC (Slow Clock Controller) + This node contains the slow clock definitions. + + "atmel,at91sam9x5-clk-slow-osc": + at91 slow oscillator + + "atmel,at91sam9x5-clk-slow-rc-osc": + at91 internal slow RC oscillator + "atmel,at91rm9200-pmc" or "atmel,at91sam9g45-pmc" or "atmel,at91sam9n12-pmc" or @@ -15,8 +25,18 @@ Required properties: All at91 specific clocks (clocks defined below) must be child node of the PMC node. + "atmel,at91sam9x5-clk-slow" (under sckc node) + or + "atmel,at91sam9260-clk-slow" (under pmc node): + at91 slow clk + + "atmel,at91rm9200-clk-main-osc" + "atmel,at91sam9x5-clk-main-rc-osc" + at91 main clk sources + + "atmel,at91sam9x5-clk-main" "atmel,at91rm9200-clk-main": - at91 main oscillator + at91 main clock "atmel,at91rm9200-clk-master" or "atmel,at91sam9x5-clk-master": @@ -54,6 +74,63 @@ Required properties: "atmel,at91sam9x5-clk-utmi": at91 utmi clock +Required properties for SCKC node: +- reg : defines the IO memory reserved for the SCKC. +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). + + +For example: + sckc: sckc@fffffe50 { + compatible = "atmel,sama5d3-pmc"; + reg = <0xfffffe50 0x4> + #size-cells = <0>; + #address-cells = <1>; + + /* put at91 slow clocks here */ + }; + + +Required properties for internal slow RC oscillator: +- #clock-cells : from common clock binding; shall be set to 0. +- clock-frequency : define the internal RC oscillator frequency. + +Optional properties: +- clock-accuracy : define the internal RC oscillator accuracy. + +For example: + slow_rc_osc: slow_rc_osc { + compatible = "atmel,at91sam9x5-clk-slow-rc-osc"; + clock-frequency = <32768>; + clock-accuracy = <50000000>; + }; + +Required properties for slow oscillator: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the main osc source clk sources (see atmel datasheet). + +Optional properties: +- atmel,osc-bypass : boolean property. Set this when a clock signal is directly + provided on XIN. + +For example: + slow_osc: slow_osc { + compatible = "atmel,at91rm9200-clk-slow-osc"; + #clock-cells = <0>; + clocks = <&slow_xtal>; + }; + +Required properties for slow clock: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the slow clk sources (see atmel datasheet). + +For example: + clk32k: slck { + compatible = "atmel,at91sam9x5-clk-slow"; + #clock-cells = <0>; + clocks = <&slow_rc_osc &slow_osc>; + }; + Required properties for PMC node: - reg : defines the IO memory reserved for the PMC. - #size-cells : shall be 0 (reg is used to encode clk id). @@ -62,7 +139,7 @@ Required properties for PMC node: - interrupt-controller : tell that the PMC is an interrupt controller. - #interrupt-cells : must be set to 1. The first cell encodes the interrupt id, and reflect the bit position in the PMC_ER/DR/SR registers. - You can use the dt macros defined in dt-bindings/clk/at91.h. + You can use the dt macros defined in dt-bindings/clock/at91.h. 0 (AT91_PMC_MOSCS) -> main oscillator ready 1 (AT91_PMC_LOCKA) -> PLL A ready 2 (AT91_PMC_LOCKB) -> PLL B ready @@ -85,24 +162,57 @@ For example: /* put at91 clocks here */ }; +Required properties for main clock internal RC oscillator: +- interrupt-parent : must reference the PMC node. +- interrupts : shall be set to "<0>". +- clock-frequency : define the internal RC oscillator frequency. + +Optional properties: +- clock-accuracy : define the internal RC oscillator accuracy. + +For example: + main_rc_osc: main_rc_osc { + compatible = "atmel,at91sam9x5-clk-main-rc-osc"; + interrupt-parent = <&pmc>; + interrupts = <0>; + clock-frequency = <12000000>; + clock-accuracy = <50000000>; + }; + +Required properties for main clock oscillator: +- interrupt-parent : must reference the PMC node. +- interrupts : shall be set to "<0>". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the main osc source clk sources (see atmel datasheet). + +Optional properties: +- atmel,osc-bypass : boolean property. Specified if a clock signal is provided + on XIN. + + clock signal is directly provided on XIN pin. + +For example: + main_osc: main_osc { + compatible = "atmel,at91rm9200-clk-main-osc"; + interrupt-parent = <&pmc>; + interrupts = <0>; + #clock-cells = <0>; + clocks = <&main_xtal>; + }; + Required properties for main clock: - interrupt-parent : must reference the PMC node. - interrupts : shall be set to "<0>". - #clock-cells : from common clock binding; shall be set to 0. -- clocks (optional if clock-frequency is provided) : shall be the slow clock - phandle. This clock is used to calculate the main clock rate if - "clock-frequency" is not provided. -- clock-frequency : the main oscillator frequency.Prefer the use of - "clock-frequency" over automatic clock rate calculation. +- clocks : shall encode the main clk sources (see atmel datasheet). For example: main: mainck { - compatible = "atmel,at91rm9200-clk-main"; + compatible = "atmel,at91sam9x5-clk-main"; interrupt-parent = <&pmc>; interrupts = <0>; #clock-cells = <0>; - clocks = <&ck32k>; - clock-frequency = <18432000>; + clocks = <&main_rc_osc &main_osc>; }; Required properties for master clock: diff --git a/Documentation/devicetree/bindings/clock/exynos3250-clock.txt b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt new file mode 100644 index 00000000000..aadc9c59e2d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt @@ -0,0 +1,41 @@ +* Samsung Exynos3250 Clock Controller + +The Exynos3250 clock controller generates and supplies clock to various +controllers within the Exynos3250 SoC. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,exynos3250-cmu" - controller compatible with Exynos3250 SoC. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos3250.h header and can be used in device +tree sources. + +Example 1: An example of a clock controller node is listed below. + + cmu: clock-controller@10030000 { + compatible = "samsung,exynos3250-cmu"; + reg = <0x10030000 0x20000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + + serial@13800000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x13800000 0x100>; + interrupts = <0 109 0>; + clocks = <&cmu CLK_UART0>, <&cmu CLK_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos5260-clock.txt b/Documentation/devicetree/bindings/clock/exynos5260-clock.txt new file mode 100644 index 00000000000..5496b2fac48 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos5260-clock.txt @@ -0,0 +1,190 @@ +* Samsung Exynos5260 Clock Controller + +Exynos5260 has 13 clock controllers which are instantiated +independently from the device-tree. These clock controllers +generate and supply clocks to various hardware blocks within +the SoC. + +Each clock is assigned an identifier and client nodes can use +this identifier to specify the clock which they consume. All +available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5260-clk.h header and can be used in +device tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It +is expected that they are defined using standard clock bindings +with following clock-output-names: + + - "fin_pll" - PLL input clock from XXTI + - "xrtcxti" - input clock from XRTCXTI + - "ioclk_pcm_extclk" - pcm external operation clock + - "ioclk_spdif_extclk" - spdif external operation clock + - "ioclk_i2s_cdclk" - i2s0 codec clock + +Phy clocks: + +There are several clocks which are generated by specific PHYs. +These clocks are fed into the clock controller and then routed to +the hardware blocks. These clocks are defined as fixed clocks in the +driver with following names: + + - "phyclk_dptx_phy_ch3_txd_clk" - dp phy clock for channel 3 + - "phyclk_dptx_phy_ch2_txd_clk" - dp phy clock for channel 2 + - "phyclk_dptx_phy_ch1_txd_clk" - dp phy clock for channel 1 + - "phyclk_dptx_phy_ch0_txd_clk" - dp phy clock for channel 0 + - "phyclk_hdmi_phy_tmds_clko" - hdmi phy tmds clock + - "phyclk_hdmi_phy_pixel_clko" - hdmi phy pixel clock + - "phyclk_hdmi_link_o_tmds_clkhi" - hdmi phy for hdmi link + - "phyclk_dptx_phy_o_ref_clk_24m" - dp phy reference clock + - "phyclk_dptx_phy_clk_div2" + - "phyclk_mipi_dphy_4l_m_rxclkesc0" + - "phyclk_usbhost20_phy_phyclock" - usb 2.0 phy clock + - "phyclk_usbhost20_phy_freeclk" + - "phyclk_usbhost20_phy_clk48mohci" + - "phyclk_usbdrd30_udrd30_pipe_pclk" + - "phyclk_usbdrd30_udrd30_phyclock" - usb 3.0 phy clock + +Required Properties for Clock Controller: + + - compatible: should be one of the following. + 1) "samsung,exynos5260-clock-top" + 2) "samsung,exynos5260-clock-peri" + 3) "samsung,exynos5260-clock-egl" + 4) "samsung,exynos5260-clock-kfc" + 5) "samsung,exynos5260-clock-g2d" + 6) "samsung,exynos5260-clock-mif" + 7) "samsung,exynos5260-clock-mfc" + 8) "samsung,exynos5260-clock-g3d" + 9) "samsung,exynos5260-clock-fsys" + 10) "samsung,exynos5260-clock-aud" + 11) "samsung,exynos5260-clock-isp" + 12) "samsung,exynos5260-clock-gscl" + 13) "samsung,exynos5260-clock-disp" + + - reg: physical base address of the controller and the length of + memory mapped region. + + - #clock-cells: should be 1. + + - clocks: list of clock identifiers which are fed as the input to + the given clock controller. Please refer the next section to find + the input clocks for a given controller. + + - clock-names: list of names of clocks which are fed as the input + to the given clock controller. + +Input clocks for top clock controller: + - fin_pll + - dout_mem_pll + - dout_bus_pll + - dout_media_pll + +Input clocks for peri clock controller: + - fin_pll + - ioclk_pcm_extclk + - ioclk_i2s_cdclk + - ioclk_spdif_extclk + - phyclk_hdmi_phy_ref_cko + - dout_aclk_peri_66 + - dout_sclk_peri_uart0 + - dout_sclk_peri_uart1 + - dout_sclk_peri_uart2 + - dout_sclk_peri_spi0_b + - dout_sclk_peri_spi1_b + - dout_sclk_peri_spi2_b + - dout_aclk_peri_aud + - dout_sclk_peri_spi0_b + +Input clocks for egl clock controller: + - fin_pll + - dout_bus_pll + +Input clocks for kfc clock controller: + - fin_pll + - dout_media_pll + +Input clocks for g2d clock controller: + - fin_pll + - dout_aclk_g2d_333 + +Input clocks for mif clock controller: + - fin_pll + +Input clocks for mfc clock controller: + - fin_pll + - dout_aclk_mfc_333 + +Input clocks for g3d clock controller: + - fin_pll + +Input clocks for fsys clock controller: + - fin_pll + - phyclk_usbhost20_phy_phyclock + - phyclk_usbhost20_phy_freeclk + - phyclk_usbhost20_phy_clk48mohci + - phyclk_usbdrd30_udrd30_pipe_pclk + - phyclk_usbdrd30_udrd30_phyclock + - dout_aclk_fsys_200 + +Input clocks for aud clock controller: + - fin_pll + - fout_aud_pll + - ioclk_i2s_cdclk + - ioclk_pcm_extclk + +Input clocks for isp clock controller: + - fin_pll + - dout_aclk_isp1_266 + - dout_aclk_isp1_400 + - mout_aclk_isp1_266 + +Input clocks for gscl clock controller: + - fin_pll + - dout_aclk_gscl_400 + - dout_aclk_gscl_333 + +Input clocks for disp clock controller: + - fin_pll + - phyclk_dptx_phy_ch3_txd_clk + - phyclk_dptx_phy_ch2_txd_clk + - phyclk_dptx_phy_ch1_txd_clk + - phyclk_dptx_phy_ch0_txd_clk + - phyclk_hdmi_phy_tmds_clko + - phyclk_hdmi_phy_ref_clko + - phyclk_hdmi_phy_pixel_clko + - phyclk_hdmi_link_o_tmds_clkhi + - phyclk_mipi_dphy_4l_m_txbyte_clkhs + - phyclk_dptx_phy_o_ref_clk_24m + - phyclk_dptx_phy_clk_div2 + - phyclk_mipi_dphy_4l_m_rxclkesc0 + - phyclk_hdmi_phy_ref_cko + - ioclk_spdif_extclk + - dout_aclk_peri_aud + - dout_aclk_disp_222 + - dout_sclk_disp_pixel + - dout_aclk_disp_333 + +Example 1: An example of a clock controller node is listed below. + + clock_mfc: clock-controller@11090000 { + compatible = "samsung,exynos5260-clock-mfc"; + clock = <&fin_pll>, <&clock_top TOP_DOUT_ACLK_MFC_333>; + clock-names = "fin_pll", "dout_aclk_mfc_333"; + reg = <0x11090000 0x10000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the + peri clock controller. Refer to the standard clock bindings for + information about 'clocks' and 'clock-names' property. + + serial@12C00000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C00000 0x100>; + interrupts = <0 146 0>; + clocks = <&clock_peri PERI_PCLK_UART0>, <&clock_peri PERI_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + }; + diff --git a/Documentation/devicetree/bindings/clock/exynos5410-clock.txt b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt new file mode 100644 index 00000000000..aeab635b07b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt @@ -0,0 +1,45 @@ +* Samsung Exynos5410 Clock Controller + +The Exynos5410 clock controller generates and supplies clock to various +controllers within the Exynos5410 SoC. + +Required Properties: + +- compatible: should be "samsung,exynos5410-clock" + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5410.h header and can be used in device +tree sources. + +External clock: + +There is clock that is generated outside the SoC. It +is expected that it is defined using standard clock bindings +with following clock-output-name: + + - "fin_pll" - PLL input clock from XXTI + +Example 1: An example of a clock controller node is listed below. + + clock: clock-controller@0x10010000 { + compatible = "samsung,exynos5410-clock"; + reg = <0x10010000 0x30000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + + serial@12C20000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C00000 0x100>; + interrupts = <0 51 0>; + clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt index ca88c97a856..d54f42cf044 100644 --- a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt @@ -1,12 +1,13 @@ * Samsung Exynos5420 Clock Controller The Exynos5420 clock controller generates and supplies clock to various -controllers within the Exynos5420 SoC. +controllers within the Exynos5420 SoC and for the Exynos5800 SoC. Required Properties: - compatible: should be one of the following. - "samsung,exynos5420-clock" - controller compatible with Exynos5420 SoC. + - "samsung,exynos5800-clock" - controller compatible with Exynos5800 SoC. - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/clock/imx25-clock.txt b/Documentation/devicetree/bindings/clock/imx25-clock.txt index db4f2f05c4d..ba6b312ff8a 100644 --- a/Documentation/devicetree/bindings/clock/imx25-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx25-clock.txt @@ -139,6 +139,9 @@ clocks and IDs. uart5_ipg 124 reserved 125 wdt_ipg 126 + cko_div 127 + cko_sel 128 + cko 129 Examples: diff --git a/Documentation/devicetree/bindings/clock/imx27-clock.txt b/Documentation/devicetree/bindings/clock/imx27-clock.txt index 7a207039373..6bc9fd2c663 100644 --- a/Documentation/devicetree/bindings/clock/imx27-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx27-clock.txt @@ -98,7 +98,12 @@ clocks and IDs. fpm 83 mpll_osc_sel 84 mpll_sel 85 - spll_gate 86 + spll_gate 86 + mshc_div 87 + rtic_ipg_gate 88 + mshc_ipg_gate 89 + rtic_ahb_gate 90 + mshc_baud_gate 91 Examples: diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt index 6aab72bf67e..90ec91fe5ce 100644 --- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -220,6 +220,7 @@ clocks and IDs. lvds2_sel 205 lvds1_gate 206 lvds2_gate 207 + esai_ahb 208 Examples: diff --git a/Documentation/devicetree/bindings/clock/imx6sx-clock.txt b/Documentation/devicetree/bindings/clock/imx6sx-clock.txt new file mode 100644 index 00000000000..22362b9b7ba --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6sx-clock.txt @@ -0,0 +1,13 @@ +* Clock bindings for Freescale i.MX6 SoloX + +Required properties: +- compatible: Should be "fsl,imx6sx-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include entries "ckil", "osc", "ipp_di0" and "ipp_di1" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6sx-clock.h +for the full list of i.MX6 SoloX clock IDs. diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt index 5992dceec7a..6c3c0847e4f 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt @@ -10,6 +10,7 @@ index in the group, from 0 to 31. Required Properties: - compatible: Must be one of the following + - "renesas,r7s72100-mstp-clocks" for R7S72100 (RZ) MSTP gate clocks - "renesas,r8a7790-mstp-clocks" for R8A7790 (R-Car H2) MSTP gate clocks - "renesas,r8a7791-mstp-clocks" for R8A7791 (R-Car M2) MSTP gate clocks - "renesas,cpg-mstp-clock" for generic MSTP gate clocks @@ -43,7 +44,7 @@ Example clock-output-names = "tpu0", "mmcif1", "sdhi3", "sdhi2", "sdhi1", "sdhi0", "mmcif0"; - renesas,clock-indices = < + clock-indices = < R8A7790_CLK_TPU0 R8A7790_CLK_MMCIF1 R8A7790_CLK_SDHI3 R8A7790_CLK_SDHI2 R8A7790_CLK_SDHI1 R8A7790_CLK_SDHI0 R8A7790_CLK_MMCIF0 diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt new file mode 100644 index 00000000000..822505e715a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt @@ -0,0 +1,50 @@ +* Samsung S3C2410 Clock Controller + +The S3C2410 clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to the s3c2410, +s3c2440 and s3c2442 SoCs in the s3c24x family. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,s3c2410-clock" - controller compatible with S3C2410 SoC. + - "samsung,s3c2440-clock" - controller compatible with S3C2440 SoC. + - "samsung,s3c2442-clock" - controller compatible with S3C2442 SoC. +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular SoC. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s3c2410.h header and can be used in device +tree sources. + +External clocks: + +The xti clock used as input for the plls is generated outside the SoC. It is +expected that is are defined using standard clock bindings with a +clock-output-names value of "xti". + +Example: Clock controller node: + + clocks: clock-controller@4c000000 { + compatible = "samsung,s3c2410-clock"; + reg = <0x4c000000 0x20>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + serial@50004000 { + compatible = "samsung,s3c2440-uart"; + reg = <0x50004000 0x4000>; + interrupts = <1 23 3 4>, <1 23 4 4>; + clock-names = "uart", "clk_uart_baud2"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt new file mode 100644 index 00000000000..2b430960ba4 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt @@ -0,0 +1,50 @@ +* Samsung S3C2412 Clock Controller + +The S3C2412 clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to the s3c2412 +and s3c2413 SoCs in the s3c24x family. + +Required Properties: + +- compatible: should be "samsung,s3c2412-clock" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular SoC. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s3c2412.h header and can be used in device +tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xti" - crystal input - required, + - "ext" - external clock source - optional, + +Example: Clock controller node: + + clocks: clock-controller@4c000000 { + compatible = "samsung,s3c2412-clock"; + reg = <0x4c000000 0x20>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + serial@50004000 { + compatible = "samsung,s3c2412-uart"; + reg = <0x50004000 0x4000>; + interrupts = <1 23 3 4>, <1 23 4 4>; + clock-names = "uart", "clk_uart_baud2", "clk_uart_baud3"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>, + <&clocks SCLK_UART>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt new file mode 100644 index 00000000000..e67bb05478a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt @@ -0,0 +1,56 @@ +* Samsung S3C2443 Clock Controller + +The S3C2443 clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to all SoCs in +the s3c24x family starting with the s3c2443. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,s3c2416-clock" - controller compatible with S3C2416 SoC. + - "samsung,s3c2443-clock" - controller compatible with S3C2443 SoC. + - "samsung,s3c2450-clock" - controller compatible with S3C2450 SoC. +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular SoC. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s3c2443.h header and can be used in device +tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xti" - crystal input - required, + - "ext" - external clock source - optional, + - "ext_i2s" - external I2S clock - optional, + - "ext_uart" - external uart clock - optional, + +Example: Clock controller node: + + clocks: clock-controller@4c000000 { + compatible = "samsung,s3c2416-clock"; + reg = <0x4c000000 0x40>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + serial@50004000 { + compatible = "samsung,s3c2440-uart"; + reg = <0x50004000 0x4000>; + interrupts = <1 23 3 4>, <1 23 4 4>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>, + <&clocks SCLK_UART>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt b/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt new file mode 100644 index 00000000000..3e6a81e9980 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt @@ -0,0 +1,20 @@ +* Device tree bindings for Texas Instruments keystone pll controller + +The main pll controller used to drive theC66x CorePacs, the switch fabric, +and a majority of the peripheral clocks (all but the ARM CorePacs, DDR3 and +the NETCP modules) requires a PLL Controller to manage the various clock +divisions, gating, and synchronization. + +Required properties: + +- compatible: "ti,keystone-pllctrl", "syscon" + +- reg: contains offset/length value for pll controller + registers space. + +Example: + +pllctrl: pll-controller@0x02310000 { + compatible = "ti,keystone-pllctrl", "syscon"; + reg = <0x02310000 0x200>; +}; diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt index 9fbbdb783a7..5ba525a1003 100644 --- a/Documentation/devicetree/bindings/dma/ti-edma.txt +++ b/Documentation/devicetree/bindings/dma/ti-edma.txt @@ -2,11 +2,8 @@ TI EDMA Required properties: - compatible : "ti,edma3" -- ti,edma-regions: Number of regions -- ti,edma-slots: Number of slots - #dma-cells: Should be set to <1> Clients should use a single channel number per DMA request. -- dma-channels: Specify total DMA channels per CC - reg: Memory map for accessing module - interrupt-parent: Interrupt controller the interrupt is routed through - interrupts: Exactly 3 interrupts need to be specified in the order: @@ -17,6 +14,13 @@ Optional properties: - ti,hwmods: Name of the hwmods associated to the EDMA - ti,edma-xbar-event-map: Crossbar event to channel map +Deprecated properties: +Listed here in case one wants to boot an old kernel with new DTB. These +properties might need to be added to the new DTS files. +- ti,edma-regions: Number of regions +- ti,edma-slots: Number of slots +- dma-channels: Specify total DMA channels per CC + Example: edma: edma@49000000 { @@ -26,9 +30,6 @@ edma: edma@49000000 { compatible = "ti,edma3"; ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; #dma-cells = <1>; - dma-channels = <64>; - ti,edma-regions = <4>; - ti,edma-slots = <256>; - ti,edma-xbar-event-map = <1 12 - 2 13>; + ti,edma-xbar-event-map = /bits/ 16 <1 12 + 2 13>; }; diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index f61cef74a21..941a26aa432 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -21,6 +21,12 @@ Required Properties: GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. - gpio-ranges: Range of pins managed by the GPIO controller. +Optional properties: + + - clocks: Must contain a reference to the functional clock. The property is + mandatory if the hardware implements a controllable functional clock for + the GPIO instance. + Please refer to gpio.txt in this directory for details of gpio-ranges property and the common GPIO bindings used by client devices. diff --git a/Documentation/devicetree/bindings/hsi/client-devices.txt b/Documentation/devicetree/bindings/hsi/client-devices.txt new file mode 100644 index 00000000000..104c9a3e57a --- /dev/null +++ b/Documentation/devicetree/bindings/hsi/client-devices.txt @@ -0,0 +1,44 @@ +Each HSI port is supposed to have one child node, which +symbols the remote device connected to the HSI port. The +following properties are standardized for HSI clients: + +Required HSI configuration properties: + +- hsi-channel-ids: A list of channel ids + +- hsi-rx-mode: Receiver Bit transmission mode ("stream" or "frame") +- hsi-tx-mode: Transmitter Bit transmission mode ("stream" or "frame") +- hsi-mode: May be used instead hsi-rx-mode and hsi-tx-mode if + the transmission mode is the same for receiver and + transmitter +- hsi-speed-kbps: Max bit transmission speed in kbit/s +- hsi-flow: RX flow type ("synchronized" or "pipeline") +- hsi-arb-mode: Arbitration mode for TX frame ("round-robin", "priority") + +Optional HSI configuration properties: + +- hsi-channel-names: A list with one name per channel specified in the + hsi-channel-ids property + + +Device Tree node example for an HSI client: + +hsi-controller { + hsi-port { + modem: hsi-client { + compatible = "nokia,n900-modem"; + + hsi-channel-ids = <0>, <1>, <2>, <3>; + hsi-channel-names = "mcsaab-control", + "speech-control", + "speech-data", + "mcsaab-data"; + hsi-speed-kbps = <55000>; + hsi-mode = "frame"; + hsi-flow = "synchronized"; + hsi-arb-mode = "round-robin"; + + /* more client specific properties */ + }; + }; +}; diff --git a/Documentation/devicetree/bindings/hsi/nokia-modem.txt b/Documentation/devicetree/bindings/hsi/nokia-modem.txt new file mode 100644 index 00000000000..8a979780452 --- /dev/null +++ b/Documentation/devicetree/bindings/hsi/nokia-modem.txt @@ -0,0 +1,57 @@ +Nokia modem client bindings + +The Nokia modem HSI client follows the common HSI client binding +and inherits all required properties. The following additional +properties are needed by the Nokia modem HSI client: + +Required properties: +- compatible: Should be one of + "nokia,n900-modem" +- hsi-channel-names: Should contain the following strings + "mcsaab-control" + "speech-control" + "speech-data" + "mcsaab-data" +- gpios: Should provide a GPIO handler for each GPIO listed in + gpio-names +- gpio-names: Should contain the following strings + "cmt_apeslpx" + "cmt_rst_rq" + "cmt_en" + "cmt_rst" + "cmt_bsi" +- interrupts: Should be IRQ handle for modem's reset indication + +Example: + +&ssi_port { + modem: hsi-client { + compatible = "nokia,n900-modem"; + + pinctrl-names = "default"; + pinctrl-0 = <&modem_pins>; + + hsi-channel-ids = <0>, <1>, <2>, <3>; + hsi-channel-names = "mcsaab-control", + "speech-control", + "speech-data", + "mcsaab-data"; + hsi-speed-kbps = <55000>; + hsi-mode = "frame"; + hsi-flow = "synchronized"; + hsi-arb-mode = "round-robin"; + + interrupts-extended = <&gpio3 8 IRQ_TYPE_EDGE_FALLING>; /* 72 */ + + gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>, /* 70 */ + <&gpio3 9 GPIO_ACTIVE_HIGH>, /* 73 */ + <&gpio3 10 GPIO_ACTIVE_HIGH>, /* 74 */ + <&gpio3 11 GPIO_ACTIVE_HIGH>, /* 75 */ + <&gpio5 29 GPIO_ACTIVE_HIGH>; /* 157 */ + gpio-names = "cmt_apeslpx", + "cmt_rst_rq", + "cmt_en", + "cmt_rst", + "cmt_bsi"; + }; +}; diff --git a/Documentation/devicetree/bindings/hsi/omap-ssi.txt b/Documentation/devicetree/bindings/hsi/omap-ssi.txt new file mode 100644 index 00000000000..f26625e4269 --- /dev/null +++ b/Documentation/devicetree/bindings/hsi/omap-ssi.txt @@ -0,0 +1,97 @@ +OMAP SSI controller bindings + +OMAP Synchronous Serial Interface (SSI) controller implements a legacy +variant of MIPI's High Speed Synchronous Serial Interface (HSI). + +Required properties: +- compatible: Should include "ti,omap3-ssi". +- reg-names: Contains the values "sys" and "gdd" (in this order). +- reg: Contains a matching register specifier for each entry + in reg-names. +- interrupt-names: Contains the value "gdd_mpu". +- interrupts: Contains matching interrupt information for each entry + in interrupt-names. +- ranges: Represents the bus address mapping between the main + controller node and the child nodes below. +- clock-names: Must include the following entries: + "ssi_ssr_fck": The OMAP clock of that name + "ssi_sst_fck": The OMAP clock of that name + "ssi_ick": The OMAP clock of that name +- clocks: Contains a matching clock specifier for each entry in + clock-names. +- #address-cells: Should be set to <1> +- #size-cells: Should be set to <1> + +Each port is represented as a sub-node of the ti,omap3-ssi device. + +Required Port sub-node properties: +- compatible: Should be set to the following value + ti,omap3-ssi-port (applicable to OMAP34xx devices) +- reg-names: Contains the values "tx" and "rx" (in this order). +- reg: Contains a matching register specifier for each entry + in reg-names. +- interrupt-parent Should be a phandle for the interrupt controller +- interrupts: Should contain interrupt specifiers for mpu interrupts + 0 and 1 (in this order). +- ti,ssi-cawake-gpio: Defines which GPIO pin is used to signify CAWAKE + events for the port. This is an optional board-specific + property. If it's missing the port will not be + enabled. + +Example for Nokia N900: + +ssi-controller@48058000 { + compatible = "ti,omap3-ssi"; + + /* needed until hwmod is updated to use the compatible string */ + ti,hwmods = "ssi"; + + reg = <0x48058000 0x1000>, + <0x48059000 0x1000>; + reg-names = "sys", + "gdd"; + + interrupts = <55>; + interrupt-names = "gdd_mpu"; + + clocks = <&ssi_ssr_fck>, + <&ssi_sst_fck>, + <&ssi_ick>; + clock-names = "ssi_ssr_fck", + "ssi_sst_fck", + "ssi_ick"; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + ssi-port@4805a000 { + compatible = "ti,omap3-ssi-port"; + + reg = <0x4805a000 0x800>, + <0x4805a800 0x800>; + reg-names = "tx", + "rx"; + + interrupt-parent = <&intc>; + interrupts = <67>, + <68>; + + ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */ + } + + ssi-port@4805a000 { + compatible = "ti,omap3-ssi-port"; + + reg = <0x4805b000 0x800>, + <0x4805b800 0x800>; + reg-names = "tx", + "rx"; + + interrupt-parent = <&intc>; + interrupts = <69>, + <70>; + + status = "disabled"; /* second port is not used on N900 */ + } +} diff --git a/Documentation/devicetree/bindings/iio/proximity/as3935.txt b/Documentation/devicetree/bindings/iio/proximity/as3935.txt new file mode 100644 index 00000000000..ae23dd8da73 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/as3935.txt @@ -0,0 +1,28 @@ +Austrian Microsystems AS3935 Franklin lightning sensor device driver + +Required properties: + - compatible: must be "ams,as3935" + - reg: SPI chip select number for the device + - spi-cpha: SPI Mode 1. Refer to spi/spi-bus.txt for generic SPI + slave node bindings. + - interrupt-parent : should be the phandle for the interrupt controller + - interrupts : the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic + interrupt client node bindings. + +Optional properties: + - ams,tuning-capacitor-pf: Calibration tuning capacitor stepping + value 0 - 120pF. This will require using the calibration data from + the manufacturer. + +Example: + +as3935@0 { + compatible = "ams,as3935"; + reg = <0>; + spi-cpha; + interrupt-parent = <&gpio1>; + interrupts = <16 1>; + ams,tuning-capacitor-pf = <80>; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt index 653c90c34a7..1ee3bc09f31 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt @@ -6,10 +6,11 @@ The actual devices are instantiated from the child nodes of a Device Bus node. Required properties: - - compatible: Currently only Armada 370/XP SoC are supported, - with this compatible string: + - compatible: Armada 370/XP SoC are supported using the + "marvell,mvebu-devbus" compatible string. - marvell,mvebu-devbus + Orion5x SoC are supported using the + "marvell,orion-devbus" compatible string. - reg: A resource specifier for the register space. This is the base address of a chip select within @@ -22,7 +23,14 @@ Required properties: integer values for each chip-select line in use: 0 <physical address of mapping> <size> -Mandatory timing properties for child nodes: +Optional properties: + + - devbus,keep-config This property can optionally be used to keep + using the timing parameters set by the + bootloader. It makes all the timing properties + described below unused. + +Timing properties for child nodes: Read parameters: @@ -30,21 +38,26 @@ Read parameters: drive the AD bus after the completion of a device read. This prevents contentions on the Device Bus after a read cycle from a slow device. + Mandatory, except if devbus,keep-config is used. - - devbus,bus-width: Defines the bus width (e.g. <16>) + - devbus,bus-width: Defines the bus width, in bits (e.g. <16>). + Mandatory, except if devbus,keep-config is used. - devbus,badr-skew-ps: Defines the time delay from from A[2:0] toggle, to read data sample. This parameter is useful for synchronous pipelined devices, where the address precedes the read data by one or two cycles. + Mandatory, except if devbus,keep-config is used. - devbus,acc-first-ps: Defines the time delay from the negation of ALE[0] to the cycle that the first read data is sampled by the controller. + Mandatory, except if devbus,keep-config is used. - devbus,acc-next-ps: Defines the time delay between the cycle that samples data N and the cycle that samples data N+1 (in burst accesses). + Mandatory, except if devbus,keep-config is used. - devbus,rd-setup-ps: Defines the time delay between DEV_CSn assertion to DEV_OEn assertion. If set to 0 (default), @@ -52,6 +65,8 @@ Read parameters: This parameter has no affect on <acc-first-ps> parameter (no affect on first data sample). Set <rd-setup-ps> to a value smaller than <acc-first-ps>. + Mandatory for "marvell,mvebu-devbus" compatible string, + except if devbus,keep-config is used. - devbus,rd-hold-ps: Defines the time between the last data sample to the de-assertion of DEV_CSn. If set to 0 (default), @@ -62,16 +77,20 @@ Read parameters: last data sampled. Also this parameter has no affect on <turn-off-ps> parameter. Set <rd-hold-ps> to a value smaller than <turn-off-ps>. + Mandatory for "marvell,mvebu-devbus" compatible string, + except if devbus,keep-config is used. Write parameters: - devbus,ale-wr-ps: Defines the time delay from the ALE[0] negation cycle to the DEV_WEn assertion. + Mandatory. - devbus,wr-low-ps: Defines the time during which DEV_WEn is active. A[2:0] and Data are kept valid as long as DEV_WEn is active. This parameter defines the setup time of address and data to DEV_WEn rise. + Mandatory. - devbus,wr-high-ps: Defines the time during which DEV_WEn is kept inactive (high) between data beats of a burst write. @@ -79,10 +98,13 @@ Write parameters: <wr-high-ps> - <tick> ps. This parameter defines the hold time of address and data after DEV_WEn rise. + Mandatory. - devbus,sync-enable: Synchronous device enable. 1: True 0: False + Mandatory for "marvell,mvebu-devbus" compatible string, + except if devbus,keep-config is used. An example for an Armada XP GP board, with a 16 MiB NOR device as child is showed below. Note that the Device Bus driver is in charge of allocating diff --git a/Documentation/devicetree/bindings/mfd/bcm590xx.txt b/Documentation/devicetree/bindings/mfd/bcm590xx.txt index 1fe30e2b10d..be51a15e05f 100644 --- a/Documentation/devicetree/bindings/mfd/bcm590xx.txt +++ b/Documentation/devicetree/bindings/mfd/bcm590xx.txt @@ -19,7 +19,9 @@ Optional child nodes: The valid regulator node names for BCM59056 are: rfldo, camldo1, camldo2, simldo1, simldo2, sdldo, sdxldo, mmcldo1, mmcldo2, audldo, micldo, usbldo, vibldo, - csr, iosr1, iosr2, msr, sdsr1, sdsr2, vsr + csr, iosr1, iosr2, msr, sdsr1, sdsr2, vsr, + gpldo1, gpldo2, gpldo3, gpldo4, gpldo5, gpldo6, + vbus Example: pmu: bcm59056@8 { diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index 802e839b082..d81ba30c0d8 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -56,6 +56,20 @@ for a particular group of BUCKs. So provide same regulator-ramp-delay<value>. Grouping of BUCKs sharing ramp rate setting is as follow : BUCK[1, 6], BUCK[3, 4], and BUCK[7, 8, 10] +On S2MPS14 the LDO10, LDO11 and LDO12 can be configured to external control +over GPIO. To turn this feature on this property must be added to the regulator +sub-node: + - samsung,ext-control-gpios: GPIO specifier for one GPIO + controlling this regulator (enable/disable); +Example: + LDO12 { + regulator-name = "V_EMMC_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + samsung,ext-control-gpios = <&gpk0 2 0>; + }; + + The regulator constraints inside the regulator nodes use the standard regulator bindings which are documented elsewhere. diff --git a/Documentation/devicetree/bindings/misc/arm-charlcd.txt b/Documentation/devicetree/bindings/misc/arm-charlcd.txt new file mode 100644 index 00000000000..e28e2aac47f --- /dev/null +++ b/Documentation/devicetree/bindings/misc/arm-charlcd.txt @@ -0,0 +1,18 @@ +ARM Versatile Character LCD +----------------------------------------------------- +This binding defines the character LCD interface found on ARM Versatile AB +and PB reference platforms. + +Required properties: +- compatible : "arm,versatile-clcd" +- reg : Location and size of character LCD registers + +Optional properties: +- interrupts - single interrupt for character LCD. The character LCD can + operate in polled mode without an interrupt. + +Example: + lcd@10008000 { + compatible = "arm,versatile-lcd"; + reg = <0x10008000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt index 2b584cae352..03796cf2d3e 100644 --- a/Documentation/devicetree/bindings/mmc/mmci.txt +++ b/Documentation/devicetree/bindings/mmc/mmci.txt @@ -4,12 +4,58 @@ The ARM PrimeCell MMCI PL180 and PL181 provides an interface for reading and writing to MultiMedia and SD cards alike. This file documents differences between the core properties described -by mmc.txt and the properties used by the mmci driver. +by mmc.txt and the properties used by the mmci driver. Using "st" as +the prefix for a property, indicates support by the ST Micro variant. Required properties: - compatible : contains "arm,pl18x", "arm,primecell". -- arm,primecell-periphid : contains the PrimeCell Peripheral ID. +- vmmc-supply : phandle to the regulator device tree node, mentioned + as the VCC/VDD supply in the eMMC/SD specs. Optional properties: -- mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable -- mmc-cap-sd-highspeed : indicates whether SD is high speed capable +- arm,primecell-periphid : contains the PrimeCell Peripheral ID, it overrides + the ID provided by the HW +- vqmmc-supply : phandle to the regulator device tree node, mentioned + as the VCCQ/VDD_IO supply in the eMMC/SD specs. +- st,sig-dir-dat0 : bus signal direction pin used for DAT[0]. +- st,sig-dir-dat2 : bus signal direction pin used for DAT[2]. +- st,sig-dir-dat31 : bus signal direction pin used for DAT[3] and DAT[1]. +- st,sig-dir-dat74 : bus signal direction pin used for DAT[4] to DAT[7]. +- st,sig-dir-cmd : cmd signal direction pin used for CMD. +- st,sig-pin-fbclk : feedback clock signal pin used. + +Deprecated properties: +- mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable. +- mmc-cap-sd-highspeed : indicates whether SD is high speed capable. + +Example: + +sdi0_per1@80126000 { + compatible = "arm,pl18x", "arm,primecell"; + reg = <0x80126000 0x1000>; + interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>; + + dmas = <&dma 29 0 0x2>, /* Logical - DevToMem */ + <&dma 29 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "tx"; + + clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>; + clock-names = "sdi", "apb_pclk"; + + max-frequency = <100000000>; + bus-width = <4>; + cap-sd-highspeed; + cap-mmc-highspeed; + cd-gpios = <&gpio2 31 0x4>; // 95 + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-dir-cmd; + st,sig-pin-fbclk; + + vmmc-supply = <&ab8500_ldo_aux3_reg>; + vqmmc-supply = <&vmmci>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdi0_default_mode>; + pinctrl-1 = <&sdi0_sleep_mode>; +}; diff --git a/Documentation/devicetree/bindings/net/mdio-gpio.txt b/Documentation/devicetree/bindings/net/mdio-gpio.txt index c79bab02536..8dbcf8295c6 100644 --- a/Documentation/devicetree/bindings/net/mdio-gpio.txt +++ b/Documentation/devicetree/bindings/net/mdio-gpio.txt @@ -14,7 +14,7 @@ node. Example: aliases { - mdio-gpio0 = <&mdio0>; + mdio-gpio0 = &mdio0; }; mdio0: mdio { diff --git a/Documentation/devicetree/bindings/pci/host-generic-pci.txt b/Documentation/devicetree/bindings/pci/host-generic-pci.txt new file mode 100644 index 00000000000..f0b0436807b --- /dev/null +++ b/Documentation/devicetree/bindings/pci/host-generic-pci.txt @@ -0,0 +1,100 @@ +* Generic PCI host controller + +Firmware-initialised PCI host controllers and PCI emulations, such as the +virtio-pci implementations found in kvmtool and other para-virtualised +systems, do not require driver support for complexities such as regulator +and clock management. In fact, the controller may not even require the +configuration of a control interface by the operating system, instead +presenting a set of fixed windows describing a subset of IO, Memory and +Configuration Spaces. + +Such a controller can be described purely in terms of the standardized device +tree bindings communicated in pci.txt: + + +Properties of the host controller node: + +- compatible : Must be "pci-host-cam-generic" or "pci-host-ecam-generic" + depending on the layout of configuration space (CAM vs + ECAM respectively). + +- device_type : Must be "pci". + +- ranges : As described in IEEE Std 1275-1994, but must provide + at least a definition of non-prefetchable memory. One + or both of prefetchable Memory and IO Space may also + be provided. + +- bus-range : Optional property (also described in IEEE Std 1275-1994) + to indicate the range of bus numbers for this controller. + If absent, defaults to <0 255> (i.e. all buses). + +- #address-cells : Must be 3. + +- #size-cells : Must be 2. + +- reg : The Configuration Space base address and size, as accessed + from the parent bus. + + +Properties of the /chosen node: + +- linux,pci-probe-only + : Optional property which takes a single-cell argument. + If '0', then Linux will assign devices in its usual manner, + otherwise it will not try to assign devices and instead use + them as they are configured already. + +Configuration Space is assumed to be memory-mapped (as opposed to being +accessed via an ioport) and laid out with a direct correspondence to the +geography of a PCI bus address by concatenating the various components to +form an offset. + +For CAM, this 24-bit offset is: + + cfg_offset(bus, device, function, register) = + bus << 16 | device << 11 | function << 8 | register + +Whilst ECAM extends this by 4 bits to accomodate 4k of function space: + + cfg_offset(bus, device, function, register) = + bus << 20 | device << 15 | function << 12 | register + +Interrupt mapping is exactly as described in `Open Firmware Recommended +Practice: Interrupt Mapping' and requires the following properties: + +- #interrupt-cells : Must be 1 + +- interrupt-map : <see aforementioned specification> + +- interrupt-map-mask : <see aforementioned specification> + + +Example: + +pci { + compatible = "pci-host-cam-generic" + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0x1>; + + // CPU_PHYSICAL(2) SIZE(2) + reg = <0x0 0x40000000 0x0 0x1000000>; + + // BUS_ADDRESS(3) CPU_PHYSICAL(2) SIZE(2) + ranges = <0x01000000 0x0 0x01000000 0x0 0x01000000 0x0 0x00010000>, + <0x02000000 0x0 0x41000000 0x0 0x41000000 0x0 0x3f000000>; + + + #interrupt-cells = <0x1>; + + // PCI_DEVICE(3) INT#(1) CONTROLLER(PHANDLE) CONTROLLER_DATA(3) + interrupt-map = < 0x0 0x0 0x0 0x1 &gic 0x0 0x4 0x1 + 0x800 0x0 0x0 0x1 &gic 0x0 0x5 0x1 + 0x1000 0x0 0x0 0x1 &gic 0x0 0x6 0x1 + 0x1800 0x0 0x0 0x1 &gic 0x0 0x7 0x1>; + + // PCI_DEVICE(3) INT#(1) + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; +} diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt new file mode 100644 index 00000000000..d8ef5bf50f1 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -0,0 +1,66 @@ +Renesas AHB to PCI bridge +------------------------- + +This is the bridge used internally to connect the USB controllers to the +AHB. There is one bridge instance per USB port connected to the internal +OHCI and EHCI controllers. + +Required properties: +- compatible: "renesas,pci-r8a7790" for the R8A7790 SoC; + "renesas,pci-r8a7791" for the R8A7791 SoC. +- reg: A list of physical regions to access the device: the first is + the operational registers for the OHCI/EHCI controllers and the + second is for the bridge configuration and control registers. +- interrupts: interrupt for the device. +- clocks: The reference to the device clock. +- bus-range: The PCI bus number range; as this is a single bus, the range + should be specified as the same value twice. +- #address-cells: must be 3. +- #size-cells: must be 2. +- #interrupt-cells: must be 1. +- interrupt-map: standard property used to define the mapping of the PCI + interrupts to the GIC interrupts. +- interrupt-map-mask: standard property that helps to define the interrupt + mapping. + +Example SoC configuration: + + pci0: pci@ee090000 { + compatible = "renesas,pci-r8a7790"; + clocks = <&mstp7_clks R8A7790_CLK_EHCI>; + reg = <0x0 0xee090000 0x0 0xc00>, + <0x0 0xee080000 0x0 0x1100>; + interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + + bus-range = <0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xff00 0 0 0x7>; + interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; + + pci@0,1 { + reg = <0x800 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 0 0>; + phy-names = "usb"; + }; + + pci@0,2 { + reg = <0x1000 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 0 0>; + phy-names = "usb"; + }; + }; + +Example board setup: + +&pci0 { + status = "okay"; + pinctrl-0 = <&usb0_pins>; + pinctrl-names = "default"; +}; diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt new file mode 100644 index 00000000000..29d3b989d3b --- /dev/null +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -0,0 +1,47 @@ +* Renesas RCar PCIe interface + +Required properties: +- compatible: should contain one of the following + "renesas,pcie-r8a7779", "renesas,pcie-r8a7790", "renesas,pcie-r8a7791" +- reg: base address and length of the pcie controller registers. +- #address-cells: set to <3> +- #size-cells: set to <2> +- bus-range: PCI bus numbers covered +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions. +- dma-ranges: ranges for the inbound memory regions. +- interrupts: two interrupt sources for MSI interrupts, followed by interrupt + source for hardware related interrupts (e.g. link speed change). +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- clocks: from common clock binding: clock specifiers for the PCIe controller + and PCIe bus clocks. +- clock-names: from common clock binding: should be "pcie" and "pcie_bus". + +Example: + +SoC specific DT Entry: + + pcie: pcie@fe000000 { + compatible = "renesas,pcie-r8a7791"; + reg = <0 0xfe000000 0 0x80000>; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x00 0xff>; + device_type = "pci"; + ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000 + 0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000 + 0x02000000 0 0x30000000 0 0x30000000 0 0x08000000 + 0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>; + dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000 + 0x42000000 2 0x00000000 2 0x00000000 0 0x40000000>; + interrupts = <0 116 4>, <0 117 4>, <0 118 4>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 116 4>; + clocks = <&mstp3_clks R8A7791_CLK_PCIE>, <&pcie_bus_clk>; + clock-names = "pcie", "pcie_bus"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index b422e38946d..2049261d8c3 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -114,3 +114,50 @@ Example: compatible = "samsung,exynos-sataphy-i2c"; reg = <0x38>; }; + +Samsung Exynos5 SoC series USB DRD PHY controller +-------------------------------------------------- + +Required properties: +- compatible : Should be set to one of the following supported values: + - "samsung,exynos5250-usbdrd-phy" - for exynos5250 SoC, + - "samsung,exynos5420-usbdrd-phy" - for exynos5420 SoC. +- reg : Register offset and length of USB DRD PHY register set; +- clocks: Clock IDs array as required by the controller +- clock-names: names of clocks correseponding to IDs in the clock property; + Required clocks: + - phy: main PHY clock (same as USB DRD controller i.e. DWC3 IP clock), + used for register access. + - ref: PHY's reference clock (usually crystal clock), used for + PHY operations, associated by phy name. It is used to + determine bit values for clock settings register. + For Exynos5420 this is given as 'sclk_usbphy30' in CMU. +- samsung,pmu-syscon: phandle for PMU system controller interface, used to + control pmu registers for power isolation. +- #phy-cells : from the generic PHY bindings, must be 1; + +For "samsung,exynos5250-usbdrd-phy" and "samsung,exynos5420-usbdrd-phy" +compatible PHYs, the second cell in the PHY specifier identifies the +PHY id, which is interpreted as follows: + 0 - UTMI+ type phy, + 1 - PIPE3 type phy, + +Example: + usbdrd_phy: usbphy@12100000 { + compatible = "samsung,exynos5250-usbdrd-phy"; + reg = <0x12100000 0x100>; + clocks = <&clock 286>, <&clock 1>; + clock-names = "phy", "ref"; + samsung,pmu-syscon = <&pmu_system_controller>; + #phy-cells = <1>; + }; + +- aliases: For SoCs like Exynos5420 having multiple USB 3.0 DRD PHY controllers, + 'usbdrd_phy' nodes should have numbered alias in the aliases node, + in the form of usbdrdphyN, N = 0, 1... (depending on number of + controllers). +Example: + aliases { + usbdrdphy0 = &usb3_phy0; + usbdrdphy1 = &usb3_phy1; + }; diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt index a82361b6201..16528b9eb56 100644 --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt @@ -2,15 +2,26 @@ Allwinner sun4i USB PHY ----------------------- Required properties: -- compatible : should be one of "allwinner,sun4i-a10-usb-phy", - "allwinner,sun5i-a13-usb-phy" or "allwinner,sun7i-a20-usb-phy" +- compatible : should be one of + * allwinner,sun4i-a10-usb-phy + * allwinner,sun5i-a13-usb-phy + * allwinner,sun6i-a31-usb-phy + * allwinner,sun7i-a20-usb-phy - reg : a list of offset + length pairs -- reg-names : "phy_ctrl", "pmu1" and for sun4i or sun7i "pmu2" +- reg-names : + * "phy_ctrl" + * "pmu1" + * "pmu2" for sun4i, sun6i or sun7i - #phy-cells : from the generic phy bindings, must be 1 -- clocks : phandle + clock specifier for the phy clock -- clock-names : "usb_phy" +- clocks : phandle + clock specifier for the phy clocks +- clock-names : + * "usb_phy" for sun4i, sun5i or sun7i + * "usb0_phy", "usb1_phy" and "usb2_phy" for sun6i - resets : a list of phandle + reset specifier pairs -- reset-names : "usb0_reset", "usb1_reset" and for sun4i or sun7i "usb2_reset" +- reset-names : + * "usb0_reset" + * "usb1_reset" + * "usb2_reset" for sun4i, sun6i or sun7i Example: usbphy: phy@0x01c13400 { diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt index 788fb0fa376..9ce458f3294 100644 --- a/Documentation/devicetree/bindings/phy/ti-phy.txt +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -32,6 +32,11 @@ Required properties: - reg : Address and length of the register set for the device. - #phy-cells: determine the number of cells that should be given in the phandle while referencing this phy. + - clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. + - clock-names: should include: + * "wkupclk" - wakeup clock. + * "refclk" - reference clock (optional). Optional properties: - ctrl-module : phandle of the control module used by PHY driver to power on @@ -44,6 +49,8 @@ usb2phy@4a0ad080 { reg = <0x4a0ad080 0x58>; ctrl-module = <&omap_control_usb>; #phy-cells = <0>; + clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>; + clock-names = "wkupclk", "refclk"; }; TI PIPE3 PHY diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index dff0e5f995e..d8d065608ec 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -6,8 +6,13 @@ the first two functions being GPIO in and out. The configuration on the pins includes drive strength and pull-up. Required properties: -- compatible: "allwinner,<soc>-pinctrl". Supported SoCs for now are: - sun5i-a13. +- compatible: Should be one of the followings (depending on you SoC): + "allwinner,sun4i-a10-pinctrl" + "allwinner,sun5i-a10s-pinctrl" + "allwinner,sun5i-a13-pinctrl" + "allwinner,sun6i-a31-pinctrl" + "allwinner,sun6i-a31-r-pinctrl" + "allwinner,sun7i-a20-pinctrl" - reg: Should contain the register physical address and length for the pin controller. diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt new file mode 100644 index 00000000000..b1b595220f1 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt @@ -0,0 +1,36 @@ +* Freescale i.MX6 SoloX IOMUX Controller + +Please refer to fsl,imx-pinctrl.txt in this directory for common binding part +and usage. + +Required properties: +- compatible: "fsl,imx6sx-iomuxc" +- fsl,pins: each entry consists of 6 integers and represents the mux and config + setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val + input_val> are specified using a PIN_FUNC_ID macro, which can be found in + imx6sx-pinfunc.h under device tree source folder. The last integer CONFIG is + the pad setting value like pull-up on this pin. Please refer to i.MX6 SoloX + Reference Manual for detailed CONFIG settings. + +CONFIG bits definition: +PAD_CTL_HYS (1 << 16) +PAD_CTL_PUS_100K_DOWN (0 << 14) +PAD_CTL_PUS_47K_UP (1 << 14) +PAD_CTL_PUS_100K_UP (2 << 14) +PAD_CTL_PUS_22K_UP (3 << 14) +PAD_CTL_PUE (1 << 13) +PAD_CTL_PKE (1 << 12) +PAD_CTL_ODE (1 << 11) +PAD_CTL_SPEED_LOW (0 << 6) +PAD_CTL_SPEED_MED (1 << 6) +PAD_CTL_SPEED_HIGH (3 << 6) +PAD_CTL_DSE_DISABLE (0 << 3) +PAD_CTL_DSE_260ohm (1 << 3) +PAD_CTL_DSE_130ohm (2 << 3) +PAD_CTL_DSE_87ohm (3 << 3) +PAD_CTL_DSE_65ohm (4 << 3) +PAD_CTL_DSE_52ohm (5 << 3) +PAD_CTL_DSE_43ohm (6 << 3) +PAD_CTL_DSE_37ohm (7 << 3) +PAD_CTL_SRE_FAST (1 << 0) +PAD_CTL_SRE_SLOW (0 << 0) diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt new file mode 100644 index 00000000000..27570a3a174 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt @@ -0,0 +1,91 @@ +* Marvell Orion SoC pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage. + +Required properties: +- compatible: "marvell,88f5181l-pinctrl", "marvell,88f5182-pinctrl", + "marvell,88f5281-pinctrl" + +- reg: two register areas, the first one describing the first two + contiguous MPP registers, and the second one describing the single + final MPP register, separated from the previous one. + +Available mpp pins/groups and functions: +Note: brackets (x) are not part of the mpp name for marvell,function and given +only for more detailed description in this document. + +* Marvell Orion 88f5181l + +name pins functions +================================================================================ +mpp0 0 pcie(rstout), pci(req2), gpio +mpp1 1 gpio, pci(gnt2) +mpp2 2 gpio, pci(req3), pci-1(pme) +mpp3 3 gpio, pci(gnt3) +mpp4 4 gpio, pci(req4) +mpp5 5 gpio, pci(gnt4) +mpp6 6 gpio, pci(req5), pci-1(clk) +mpp7 7 gpio, pci(gnt5), pci-1(clk) +mpp8 8 gpio, ge(col) +mpp9 9 gpio, ge(rxerr) +mpp10 10 gpio, ge(crs) +mpp11 11 gpio, ge(txerr) +mpp12 12 gpio, ge(txd4) +mpp13 13 gpio, ge(txd5) +mpp14 14 gpio, ge(txd6) +mpp15 15 gpio, ge(txd7) +mpp16 16 ge(rxd4) +mpp17 17 ge(rxd5) +mpp18 18 ge(rxd6) +mpp19 19 ge(rxd7) + +* Marvell Orion 88f5182 + +name pins functions +================================================================================ +mpp0 0 pcie(rstout), pci(req2), gpio +mpp1 1 gpio, pci(gnt2) +mpp2 2 gpio, pci(req3), pci-1(pme) +mpp3 3 gpio, pci(gnt3) +mpp4 4 gpio, pci(req4), bootnand(re), sata0(prsnt) +mpp5 5 gpio, pci(gnt4), bootnand(we), sata1(prsnt) +mpp6 6 gpio, pci(req5), nand(re0), sata0(act) +mpp7 7 gpio, pci(gnt5), nand(we0), sata1(act) +mpp8 8 gpio, ge(col) +mpp9 9 gpio, ge(rxerr) +mpp10 10 gpio, ge(crs) +mpp11 11 gpio, ge(txerr) +mpp12 12 gpio, ge(txd4), nand(re1), sata0(ledprsnt) +mpp13 13 gpio, ge(txd5), nand(we1), sata1(ledprsnt) +mpp14 14 gpio, ge(txd6), nand(re2), sata0(ledact) +mpp15 15 gpio, ge(txd7), nand(we2), sata1(ledact) +mpp16 16 uart1(rxd), ge(rxd4), gpio +mpp17 17 uart1(txd), ge(rxd5), gpio +mpp18 18 uart1(cts), ge(rxd6), gpio +mpp19 19 uart1(rts), ge(rxd7), gpio + +* Marvell Orion 88f5281 + +name pins functions +================================================================================ +mpp0 0 pcie(rstout), pci(req2), gpio +mpp1 1 gpio, pci(gnt2) +mpp2 2 gpio, pci(req3), pci(pme) +mpp3 3 gpio, pci(gnt3) +mpp4 4 gpio, pci(req4), bootnand(re) +mpp5 5 gpio, pci(gnt4), bootnand(we) +mpp6 6 gpio, pci(req5), nand(re0) +mpp7 7 gpio, pci(gnt5), nand(we0) +mpp8 8 gpio, ge(col) +mpp9 9 gpio, ge(rxerr) +mpp10 10 gpio, ge(crs) +mpp11 11 gpio, ge(txerr) +mpp12 12 gpio, ge(txd4), nand(re1) +mpp13 13 gpio, ge(txd5), nand(we1) +mpp14 14 gpio, ge(txd6), nand(re2) +mpp15 15 gpio, ge(txd7), nand(we2) +mpp16 16 uart1(rxd), ge(rxd4) +mpp17 17 uart1(txd), ge(rxd5) +mpp18 18 uart1(cts), ge(rxd6) +mpp19 19 uart1(rts), ge(rxd7) diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index 4414163e76d..fa40a177164 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -156,6 +156,7 @@ input-disable - disable input on pin (no effect on output) input-schmitt-enable - enable schmitt-trigger mode input-schmitt-disable - disable schmitt-trigger mode input-debounce - debounce mode with debound time X +power-source - select between different power supplies low-power-enable - enable low power mode low-power-disable - disable low power mode output-low - set the pin to output mode with low level diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt new file mode 100644 index 00000000000..7181f925aca --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt @@ -0,0 +1,88 @@ +Qualcomm APQ8064 TLMM block + +Required properties: +- compatible: "qcom,apq8064-pinctrl" +- reg: Should be the base address and length of the TLMM block. +- interrupts: Should be the parent IRQ of the TLMM block. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. + The first cell is the gpio pin number and the + second cell is used for optional parameters. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Qualcomm's pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + + pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength, + output-low, output-high. + +Non-empty subnodes must specify the 'pins' property. + +Valid values for pins are: + gpio0-gpio89 + +Valid values for function are: + cam_mclk, codec_mic_i2s, codec_spkr_i2s, gsbi1, gsbi2, gsbi3, gsbi4, + gsbi4_cam_i2c, gsbi5, gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, + gsbi6_spi_cs1, gsbi6_spi_cs2, gsbi6_spi_cs3, gsbi7, gsbi7_spi_cs1, + gsbi7_spi_cs2, gsbi7_spi_cs3, gsbi_cam_i2c, hdmi, mi2s, riva_bt, riva_fm, + riva_wlan, sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic, + +Example: + + msmgpio: pinctrl@800000 { + compatible = "qcom,apq8064-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 32 0x4>; + + pinctrl-names = "default"; + pinctrl-0 = <&gsbi5_uart_default>; + + gsbi5_uart_default: gsbi5_uart_default { + mux { + pins = "gpio51", "gpio52"; + function = "gsbi5"; + }; + + tx { + pins = "gpio51"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio52"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt new file mode 100644 index 00000000000..e0d35a40981 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt @@ -0,0 +1,95 @@ +Qualcomm IPQ8064 TLMM block + +Required properties: +- compatible: "qcom,ipq8064-pinctrl" +- reg: Should be the base address and length of the TLMM block. +- interrupts: Should be the parent IRQ of the TLMM block. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. + The first cell is the gpio pin number and the + second cell is used for optional parameters. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Qualcomm's pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + + pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength, + output-low, output-high. + +Non-empty subnodes must specify the 'pins' property. + +Valid values for qcom,pins are: + gpio0-gpio68 + Supports mux, bias, and drive-strength + + sdc3_clk, sdc3_cmd, sdc3_data + Supports bias and drive-strength + + +Valid values for function are: + mdio, mi2s, pdm, ssbi, spmi, audio_pcm, gsbi1, gsbi2, gsbi4, gsbi5, + gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi7, nss_spi, sdc1, + spdif, nand, tsif1, tsif2, usb_fs_n, usb_fs, usb2_hsic, rgmii2, sata, + pcie1_rst, pcie1_prsnt, pcie1_pwren_n, pcie1_pwren, pcie1_pwrflt, + pcie1_clk_req, pcie2_rst, pcie2_prsnt, pcie2_pwren_n, pcie2_pwren, + pcie2_pwrflt, pcie2_clk_req, pcie3_rst, pcie3_prsnt, pcie3_pwren_n, + pcie3_pwren, pcie3_pwrflt, pcie3_clk_req, ps_hold + +Example: + + pinmux: pinctrl@800000 { + compatible = "qcom,ipq8064-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 32 0x4>; + + pinctrl-names = "default"; + pinctrl-0 = <&gsbi5_uart_default>; + + gsbi5_uart_default: gsbi5_uart_default { + mux { + pins = "gpio18", "gpio19"; + function = "gsbi5"; + }; + + tx { + pins = "gpio18"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio19"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt index 9fb89e3f61e..73262b575df 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt @@ -50,7 +50,27 @@ Valid values for pins are: Supports bias and drive-strength Valid values for function are: - blsp_i2c2, blsp_i2c6, blsp_i2c11, blsp_spi1, blsp_uart2, blsp_uart8, slimbus + cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm, + blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1, + blsp_uim2, blsp_uart2, blsp_i2c2, blsp_spi2, + blsp_uim3, blsp_uart3, blsp_i2c3, blsp_spi3, + blsp_uim4, blsp_uart4, blsp_i2c4, blsp_spi4, + blsp_uim5, blsp_uart5, blsp_i2c5, blsp_spi5, + blsp_uim6, blsp_uart6, blsp_i2c6, blsp_spi6, + blsp_uim7, blsp_uart7, blsp_i2c7, blsp_spi7, + blsp_uim8, blsp_uart8, blsp_i2c8, blsp_spi8, + blsp_uim9, blsp_uart9, blsp_i2c9, blsp_spi9, + blsp_uim10, blsp_uart10, blsp_i2c10, blsp_spi10, + blsp_uim11, blsp_uart11, blsp_i2c11, blsp_spi11, + blsp_uim12, blsp_uart12, blsp_i2c12, blsp_spi12, + blsp_spi1_cs1, blsp_spi2_cs2, blsp_spi_cs3, blsp_spi2_cs1, blsp_spi2_cs2 + blsp_spi2_cs3, blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3, + sdc3, sdc4, gcc_gp_clk1, gcc_gp_clk2, gcc_gp_clk3, cci_timer0, cci_timer1, + cci_timer2, cci_timer3, cci_async_in0, cci_async_in1, cci_async_in2, + cam_mckl0, cam_mclk1, cam_mclk2, cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc, + hdmi_hpd, edp_hpd, gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk, + gp_mn, tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s, + ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus (Note that this is not yet the complete list of functions) diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index f378d342aae..cefef741a40 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -21,13 +21,23 @@ defined as gpio sub-nodes of the pinmux controller. Required properties for iomux controller: - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl" "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl" + - rockchip,grf: phandle referencing a syscon providing the + "general register files" + +Optional properties for iomux controller: + - rockchip,pmu: phandle referencing a syscon providing the pmu registers + as some SoCs carry parts of the iomux controller registers there. + Required for at least rk3188 and rk3288. + +Deprecated properties for iomux controller: - reg: first element is the general register space of the iomux controller - second element is the separate pull register space of the rk3188 + It should be large enough to contain also separate pull registers. + second element is the separate pull register space of the rk3188. + Use rockchip,grf and rockchip,pmu described above instead. Required properties for gpio sub nodes: - compatible: "rockchip,gpio-bank", "rockchip,rk3188-gpio-bank0" - reg: register of the gpio bank (different than the iomux registerset) - second element: separate pull register for rk3188 bank0 - interrupts: base interrupt of the gpio bank in the interrupt controller - clocks: clock that drives this bank - gpio-controller: identifies the node as a gpio controller and pin bank. @@ -39,6 +49,10 @@ Required properties for gpio sub nodes: cells should use the standard two-cell scheme described in bindings/interrupt-controller/interrupts.txt +Deprecated properties for gpio sub nodes: + - reg: second element: separate pull register for rk3188 bank0, use + rockchip,pmu described above instead + Required properties for pin configuration node: - rockchip,pins: 3 integers array, represents a group of pins mux and config setting. The format is rockchip,pins = <PIN_BANK PIN_BANK_IDX MUX &phandle>. @@ -54,7 +68,8 @@ Examples: pinctrl@20008000 { compatible = "rockchip,rk3066a-pinctrl"; - reg = <0x20008000 0x150>; + rockchip,grf = <&grf>; + #address-cells = <1>; #size-cells = <1>; ranges; @@ -103,16 +118,15 @@ Example for rk3188: pinctrl@20008000 { compatible = "rockchip,rk3188-pinctrl"; - reg = <0x20008000 0xa0>, - <0x20008164 0x1a0>; + rockchip,grf = <&grf>; + rockchip,pmu = <&pmu>; #address-cells = <1>; #size-cells = <1>; ranges; gpio0: gpio0@0x2000a000 { compatible = "rockchip,rk3188-gpio-bank0"; - reg = <0x2000a000 0x100>, - <0x20004064 0x8>; + reg = <0x2000a000 0x100>; interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk_gates8 9>; diff --git a/Documentation/devicetree/bindings/power/reset/keystone-reset.txt b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt new file mode 100644 index 00000000000..c82f12e2d85 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt @@ -0,0 +1,67 @@ +* Device tree bindings for Texas Instruments keystone reset + +This node is intended to allow SoC reset in case of software reset +of selected watchdogs. + +The Keystone SoCs can contain up to 4 watchdog timers to reset +SoC. Each watchdog timer event input is connected to the Reset Mux +block. The Reset Mux block can be configured to cause reset or not. + +Additionally soft or hard reset can be configured. + +Required properties: + +- compatible: ti,keystone-reset + +- ti,syscon-pll: phandle/offset pair. The phandle to syscon used to + access pll controller registers and the offset to use + reset control registers. + +- ti,syscon-dev: phandle/offset pair. The phandle to syscon used to + access device state control registers and the offset + in order to use mux block registers for all watchdogs. + +Optional properties: + +- ti,soft-reset: Boolean option indicating soft reset. + By default hard reset is used. + +- ti,wdt-list: WDT list that can cause SoC reset. It's not related + to WDT driver, it's just needed to enable a SoC related + reset that's triggered by one of WDTs. The list is + in format: <0>, <2>; It can be in random order and + begins from 0 to 3, as keystone can contain up to 4 SoC + reset watchdogs and can be in random order. + +Example 1: +Setup keystone reset so that in case software reset or +WDT0 is triggered it issues hard reset for SoC. + +pllctrl: pll-controller@02310000 { + compatible = "ti,keystone-pllctrl", "syscon"; + reg = <0x02310000 0x200>; +}; + +devctrl: device-state-control@02620000 { + compatible = "ti,keystone-devctrl", "syscon"; + reg = <0x02620000 0x1000>; +}; + +rstctrl: reset-controller { + compatible = "ti,keystone-reset"; + ti,syscon-pll = <&pllctrl 0xe4>; + ti,syscon-dev = <&devctrl 0x328>; + ti,wdt-list = <0>; +}; + +Example 2: +Setup keystone reset so that in case of software reset or +WDT0 or WDT2 is triggered it issues soft reset for SoC. + +rstctrl: reset-controller { + compatible = "ti,keystone-reset"; + ti,syscon-pll = <&pllctrl 0xe4>; + ti,syscon-dev = <&devctrl 0x328>; + ti,wdt-list = <0>, <2>; + ti,soft-reset; +}; diff --git a/Documentation/devicetree/bindings/power_supply/axxia-reset.txt b/Documentation/devicetree/bindings/power_supply/axxia-reset.txt new file mode 100644 index 00000000000..47e720d249d --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/axxia-reset.txt @@ -0,0 +1,20 @@ +Axxia Restart Driver + +This driver can do reset of the Axxia SoC. It uses the registers in the syscon +block to initiate a chip reset. + +Required Properties: + -compatible: "lsi,axm55xx-reset" + -syscon: phandle to the syscon node. + +Example: + + syscon: syscon@2010030000 { + compatible = "lsi,axxia-syscon", "syscon"; + reg = <0x20 0x10030000 0 0x2000>; + }; + + reset: reset@2010031000 { + compatible = "lsi,axm55xx-reset"; + syscon = <&syscon>; + }; diff --git a/Documentation/devicetree/bindings/regulator/ltc3589.txt b/Documentation/devicetree/bindings/regulator/ltc3589.txt new file mode 100644 index 00000000000..80105303614 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/ltc3589.txt @@ -0,0 +1,99 @@ +Linear Technology LTC3589, LTC3589-1, and LTC3589-2 8-output regulators + +Required properties: +- compatible: "lltc,ltc3589", "lltc,ltc3589-1" or "lltc,ltc3589-2" +- reg: I2C slave address + +Required child node: +- regulators: Contains eight regulator child nodes sw1, sw2, sw3, bb-out, + ldo1, ldo2, ldo3, and ldo4, specifying the initialization data as + documented in Documentation/devicetree/bindings/regulator/regulator.txt. + +Each regulator is defined using the standard binding for regulators. The +nodes for sw1, sw2, sw3, bb-out, ldo1, and ldo2 additionally need to specify +the resistor values of their external feedback voltage dividers: + +Required properties (not on ldo3, ldo4): +- lltc,fb-voltage-divider: An array of two integers containing the resistor + values R1 and R2 of the feedback voltage divider in ohms. + +Regulators sw1, sw2, sw3, and ldo2 can regulate the feedback reference from +0.3625 V to 0.75 V in 12.5 mV steps. The output voltage thus ranges between +0.3625 * (1 + R1/R2) V and 0.75 * (1 + R1/R2) V. Regulators bb-out and ldo1 +have a fixed 0.8 V reference and thus output 0.8 * (1 + R1/R2) V. The ldo3 +regulator is fixed to 1.8 V on LTC3589 and to 2.8 V on LTC3589-1,2. The ldo4 +regulator can output between 1.8 V and 3.3 V on LTC3589 and between 1.2 V +and 3.2 V on LTC3589-1,2 in four steps. The ldo1 standby regulator can not +be disabled and thus should have the regulator-always-on property set. + +Example: + + ltc3589: pmic@34 { + compatible = "lltc,ltc3589-1"; + reg = <0x34>; + + regulators { + sw1_reg: sw1 { + regulator-min-microvolt = <591930>; + regulator-max-microvolt = <1224671>; + lltc,fb-voltage-divider = <100000 158000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <704123>; + regulator-max-microvolt = <1456803>; + lltc,fb-voltage-divider = <180000 191000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3_reg: sw3 { + regulator-min-microvolt = <1341250>; + regulator-max-microvolt = <2775000>; + lltc,fb-voltage-divider = <270000 100000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + bb_out_reg: bb-out { + regulator-min-microvolt = <3387341>; + regulator-max-microvolt = <3387341>; + lltc,fb-voltage-divider = <511000 158000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: ldo1 { + regulator-min-microvolt = <1306329>; + regulator-max-microvolt = <1306329>; + lltc,fb-voltage-divider = <100000 158000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ldo2 { + regulator-min-microvolt = <704123>; + regulator-max-microvolt = <1456806>; + lltc,fb-voltage-divider = <180000 191000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: ldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3200000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps65090.txt b/Documentation/devicetree/bindings/regulator/tps65090.txt index 313a60ba61d..340980239ea 100644 --- a/Documentation/devicetree/bindings/regulator/tps65090.txt +++ b/Documentation/devicetree/bindings/regulator/tps65090.txt @@ -21,6 +21,10 @@ Optional properties: number should be provided. If it is externally controlled and no GPIO entry then driver will just configure this rails as external control and will not provide any enable/disable APIs. +- ti,overcurrent-wait: This is applicable to FET registers, which have a + poorly defined "overcurrent wait" field. If this property is present it + should be between 0 - 3. If this property isn't present we won't touch the + "overcurrent wait" field and we'll leave it to the BIOS/EC to deal with. Each regulator is defined using the standard binding for regulators. diff --git a/Documentation/devicetree/bindings/reset/allwinner,sunxi-clock-reset.txt b/Documentation/devicetree/bindings/reset/allwinner,sunxi-clock-reset.txt new file mode 100644 index 00000000000..c8f77571488 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/allwinner,sunxi-clock-reset.txt @@ -0,0 +1,21 @@ +Allwinner sunxi Peripheral Reset Controller +=========================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be one of the following: + "allwinner,sun6i-a31-ahb1-reset" + "allwinner,sun6i-a31-clock-reset" +- reg: should be register base and length as documented in the + datasheet +- #reset-cells: 1, see below + +example: + +ahb1_rst: reset@01c202c0 { + #reset-cells = <1>; + compatible = "allwinner,sun6i-a31-ahb1-reset"; + reg = <0x01c202c0 0xc>; +}; diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-reset.txt b/Documentation/devicetree/bindings/reset/socfpga-reset.txt index ecdb57d69db..32c1c8bfd5d 100644 --- a/Documentation/devicetree/bindings/arm/altera/socfpga-reset.txt +++ b/Documentation/devicetree/bindings/reset/socfpga-reset.txt @@ -3,9 +3,11 @@ Altera SOCFPGA Reset Manager Required properties: - compatible : "altr,rst-mgr" - reg : Should contain 1 register ranges(address and length) +- #reset-cells: 1 Example: rstmgr@ffd05000 { + #reset-cells = <1>; compatible = "altr,rst-mgr"; reg = <0xffd05000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt index 17c1042b2df..a6391e70a8f 100644 --- a/Documentation/devicetree/bindings/serial/atmel-usart.txt +++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt @@ -13,8 +13,9 @@ Required properties: Optional properties: - atmel,use-dma-rx: use of PDC or DMA for receiving data - atmel,use-dma-tx: use of PDC or DMA for transmitting data -- rts-gpios: specify a GPIO for RTS line. It will use specified PIO instead of the peripheral - function pin for the USART RTS feature. If unsure, don't specify this property. +- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively. + It will use specified PIO instead of the peripheral function pin for the USART feature. + If unsure, don't specify this property. - add dma bindings for dma transfer: - dmas: DMA specifier, consisting of a phandle to DMA controller node, memory peripheral interface and USART DMA channel ID, FIFO configuration. @@ -35,7 +36,12 @@ Example: clock-names = "usart"; atmel,use-dma-rx; atmel,use-dma-tx; - rts-gpios = <&pioD 15 0>; + rts-gpios = <&pioD 15 GPIO_ACTIVE_LOW>; + cts-gpios = <&pioD 16 GPIO_ACTIVE_LOW>; + dtr-gpios = <&pioD 17 GPIO_ACTIVE_LOW>; + dsr-gpios = <&pioD 18 GPIO_ACTIVE_LOW>; + dcd-gpios = <&pioD 20 GPIO_ACTIVE_LOW>; + rng-gpios = <&pioD 19 GPIO_ACTIVE_LOW>; }; - use DMA: diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt new file mode 100644 index 00000000000..246c795668d --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt @@ -0,0 +1,33 @@ +* NXP SC16IS7xx advanced Universal Asynchronous Receiver-Transmitter (UART) + +Required properties: +- compatible: Should be one of the following: + - "nxp,sc16is740" for NXP SC16IS740, + - "nxp,sc16is741" for NXP SC16IS741, + - "nxp,sc16is750" for NXP SC16IS750, + - "nxp,sc16is752" for NXP SC16IS752, + - "nxp,sc16is760" for NXP SC16IS760, + - "nxp,sc16is762" for NXP SC16IS762. +- reg: I2C address of the SC16IS7xx device. +- interrupt-parent: The phandle for the interrupt controller that + services interrupts for this IC. +- interrupts: Should contain the UART interrupt +- clocks: Reference to the IC source clock. + +Optional properties: +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be two. The first cell is the GPIO number and + the second cell is used to specify the GPIO polarity: + 0 = active high, + 1 = active low. + +Example: + sc16is750: sc16is750@51 { + compatible = "nxp,sc16is750"; + reg = <0x51>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/of-serial.txt index 1928a3e83cd..77054772a8f 100644 --- a/Documentation/devicetree/bindings/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/serial/of-serial.txt @@ -37,6 +37,7 @@ Optional properties: - auto-flow-control: one way to enable automatic flow control support. The driver is allowed to detect support for the capability even without this property. +- has-hw-flow-control: the hardware has flow control capability. Example: diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 53e6c175db6..64fd7dec1bb 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -4,6 +4,7 @@ Required properties: - compatible: Must contain one of the following: + - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. - "renesas,scifa-r8a7790" for R8A7790 (R-Car H2) SCIFA compatible UART. - "renesas,scifb-r8a7790" for R8A7790 (R-Car H2) SCIFB compatible UART. diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt new file mode 100644 index 00000000000..4ce24d425bf --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt @@ -0,0 +1,78 @@ +QCOM GSBI (General Serial Bus Interface) Driver + +The GSBI controller is modeled as a node with zero or more child nodes, each +representing a serial sub-node device that is mux'd as part of the GSBI +configuration settings. The mode setting will govern the input/output mode of +the 4 GSBI IOs. + +Required properties: +- compatible: must contain "qcom,gsbi-v1.0.0" for APQ8064/IPQ8064 +- reg: Address range for GSBI registers +- clocks: required clock +- clock-names: must contain "iface" entry +- qcom,mode : indicates MUX value for configuration of the serial interface. + Please reference dt-bindings/soc/qcom,gsbi.h for valid mux values. + +Optional properties: +- qcom,crci : indicates CRCI MUX value for QUP CRCI ports. Please reference + dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values. + +Required properties if child node exists: +- #address-cells: Must be 1 +- #size-cells: Must be 1 +- ranges: Must be present + +Properties for children: + +A GSBI controller node can contain 0 or more child nodes representing serial +devices. These serial devices can be a QCOM UART, I2C controller, spi +controller, or some combination of aforementioned devices. + +See the following for child node definitions: +Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt +Documentation/devicetree/bindings/spi/qcom,spi-qup.txt +Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt + +Example for APQ8064: + +#include <dt-bindings/soc/qcom,gsbi.h> + + gsbi4@16300000 { + compatible = "qcom,gsbi-v1.0.0"; + reg = <0x16300000 0x100>; + clocks = <&gcc GSBI4_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + qcom,mode = <GSBI_PROT_I2C_UART>; + qcom,crci = <GSBI_CRCI_QUP>; + + /* child nodes go under here */ + + i2c_qup4: i2c@16380000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x16380000 0x1000>; + interrupts = <0 153 0>; + + clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>; + clock-names = "core", "iface"; + + clock-frequency = <200000>; + + #address-cells = <1>; + #size-cells = <0>; + + }; + + uart4: serial@16340000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x16340000 0x1000>, + <0x16300000 0x1000>; + interrupts = <0 152 0x0>; + clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>; + clock-names = "core", "iface"; + status = "ok"; + }; + }; + diff --git a/Documentation/devicetree/bindings/spi/fsl-spi.txt b/Documentation/devicetree/bindings/spi/fsl-spi.txt index b032dd76e9d..a2331372068 100644 --- a/Documentation/devicetree/bindings/spi/fsl-spi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-spi.txt @@ -42,6 +42,10 @@ Required properties: - interrupts : should contain eSPI interrupt, the device has one interrupt. - fsl,espi-num-chipselects : the number of the chipselect signals. +Optional properties: +- fsl,csbef: chip select assertion time in bits before frame starts +- fsl,csaft: chip select negation time in bits after frame ends + Example: spi@110000 { #address-cells = <1>; @@ -51,4 +55,6 @@ Example: interrupts = <53 0x2>; interrupt-parent = <&mpic>; fsl,espi-num-chipselects = <4>; + fsl,csbef = <1>; + fsl,csaft = <1>; }; diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index e5a4d1b4acf..22d57404fdc 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -55,6 +55,8 @@ contain the following properties. chip select active high - spi-3wire - (optional) Empty property indicating device requires 3-wire mode. +- spi-lsb-first - (optional) Empty property indicating device requires + LSB first mode. - spi-tx-bus-width - (optional) The bus width(number of data wires) that used for MOSI. Defaults to 1 if not present. - spi-rx-bus-width - (optional) The bus width(number of data wires) that diff --git a/Documentation/devicetree/bindings/spi/spi-cadence.txt b/Documentation/devicetree/bindings/spi/spi-cadence.txt new file mode 100644 index 00000000000..94f09141a4f --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-cadence.txt @@ -0,0 +1,31 @@ +Cadence SPI controller Device Tree Bindings +------------------------------------------- + +Required properties: +- compatible : Should be "cdns,spi-r1p6" or "xlnx,zynq-spi-r1p6". +- reg : Physical base address and size of SPI registers map. +- interrupts : Property with a value describing the interrupt + number. +- interrupt-parent : Must be core interrupt controller +- clock-names : List of input clock names - "ref_clk", "pclk" + (See clock bindings for details). +- clocks : Clock phandles (see clock bindings for details). + +Optional properties: +- num-cs : Number of chip selects used. + If a decoder is used, this will be the number of + chip selects after the decoder. +- is-decoded-cs : Flag to indicate whether decoder is used or not. + +Example: + + spi@e0007000 { + compatible = "xlnx,zynq-spi-r1p6"; + clock-names = "ref_clk", "pclk"; + clocks = <&clkc 26>, <&clkc 35>; + interrupt-parent = <&intc>; + interrupts = <0 49 4>; + num-cs = <4>; + is-decoded-cs = <0>; + reg = <0xe0007000 0x1000>; + } ; diff --git a/Documentation/devicetree/bindings/spi/spi-dw.txt b/Documentation/devicetree/bindings/spi/spi-dw.txt new file mode 100644 index 00000000000..7b63ed60199 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-dw.txt @@ -0,0 +1,24 @@ +Synopsys DesignWare SPI master + +Required properties: +- compatible: should be "snps,designware-spi" +- #address-cells: see spi-bus.txt +- #size-cells: see spi-bus.txt +- reg: address and length of the spi master registers +- interrupts: should contain one interrupt +- clocks: spi clock phandle +- num-cs: see spi-bus.txt + +Optional properties: +- cs-gpios: see spi-bus.txt + +Example: + +spi: spi@4020a000 { + compatible = "snps,designware-spi"; + interrupts = <11 1>; + reg = <0x4020a000 0x1000>; + clocks = <&pclk>; + num-cs = <2>; + cs-gpios = <&banka 0 0>; +}; diff --git a/Documentation/devicetree/bindings/spmi/spmi.txt b/Documentation/devicetree/bindings/spmi/spmi.txt index 462a42fb3a1..4bb10d161a2 100644 --- a/Documentation/devicetree/bindings/spmi/spmi.txt +++ b/Documentation/devicetree/bindings/spmi/spmi.txt @@ -26,7 +26,7 @@ Each child node must have one and only one 'reg' entry of type SPMI_USID. reg = <...>; #address-cells = <2>; - #size-cells <0>; + #size-cells = <0>; child@0 { compatible = "..."; diff --git a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt index 3be5ce7a965..e75f0e549ff 100644 --- a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt +++ b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt @@ -61,6 +61,7 @@ Required properties: Optional properties: - interface_pix_fmt: How this display is connected to the display interface. Currently supported types: "rgb24", "rgb565", "bgr666" + and "lvds666". - edid: verbatim EDID data block describing attached display. - ddc: phandle describing the i2c bus handling the display data channel diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt new file mode 100644 index 00000000000..f2899b55093 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt @@ -0,0 +1,17 @@ +Qualcomm CI13xxx (Chipidea) USB controllers + +Required properties: +- compatible: should contain "qcom,ci-hdrc" +- reg: offset and length of the register set in the memory map +- interrupts: interrupt-specifier for the controller interrupt. +- usb-phy: phandle for the PHY device +- dr_mode: Should be "peripheral" + +Examples: + gadget@f9a55000 { + compatible = "qcom,ci-hdrc"; + reg = <0xf9a55000 0x400>; + dr_mode = "peripheral"; + interrupts = <0 134 0>; + usb-phy = <&usbphy0>; + }; diff --git a/Documentation/devicetree/bindings/usb/ehci-orion.txt b/Documentation/devicetree/bindings/usb/ehci-orion.txt index 6bc09ec14c4..17c3bc858b8 100644 --- a/Documentation/devicetree/bindings/usb/ehci-orion.txt +++ b/Documentation/devicetree/bindings/usb/ehci-orion.txt @@ -6,6 +6,11 @@ Required properties: region. - interrupts: The EHCI interrupt +Optional properties: +- clocks: reference to the clock +- phys: reference to the USB PHY +- phy-names: name of the USB PHY, should be "usb" + Example: ehci@50000 { diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt index d967ba16de6..a3b5990d0f2 100644 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -12,6 +12,13 @@ Required properties: - interrupts: interrupt number to the cpu. - clocks: from common clock binding: handle to usb clock. - clock-names: from common clock binding: Shall be "usbhost". + - port: if in the SoC there are EHCI phys, they should be listed here. + One phy per port. Each port should have following entries: + - reg: port number on EHCI controller, e.g + On Exynos5250, port 0 is USB2.0 otg phy + port 1 is HSIC phy0 + port 2 is HSIC phy1 + - phys: from the *Generic PHY* bindings; specifying phy used by port. Optional properties: - samsung,vbus-gpio: if present, specifies the GPIO that @@ -27,6 +34,14 @@ Example: clocks = <&clock 285>; clock-names = "usbhost"; + + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + phys = <&usb2phy 1>; + status = "disabled"; + }; }; OHCI @@ -38,6 +53,13 @@ Required properties: - interrupts: interrupt number to the cpu. - clocks: from common clock binding: handle to usb clock. - clock-names: from common clock binding: Shall be "usbhost". + - port: if in the SoC there are OHCI phys, they should be listed here. + One phy per port. Each port should have following entries: + - reg: port number on OHCI controller, e.g + On Exynos5250, port 0 is USB2.0 otg phy + port 1 is HSIC phy0 + port 2 is HSIC phy1 + - phys: from the *Generic PHY* bindings, specifying phy used by port. Example: usb@12120000 { @@ -47,6 +69,15 @@ Example: clocks = <&clock 285>; clock-names = "usbhost"; + + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + phys = <&usb2phy 1>; + status = "disabled"; + }; + }; DWC3 diff --git a/Documentation/devicetree/bindings/usb/gr-udc.txt b/Documentation/devicetree/bindings/usb/gr-udc.txt index 0c5118f7a91..e9445224fab 100644 --- a/Documentation/devicetree/bindings/usb/gr-udc.txt +++ b/Documentation/devicetree/bindings/usb/gr-udc.txt @@ -12,17 +12,23 @@ Required properties: - reg : Address and length of the register set for the device -- interrupts : Interrupt numbers for this device +- interrupts : Interrupt numbers for this device. Either one interrupt number + for all interrupts, or one for status related interrupts, one for IN + endpoint related interrupts and one for OUT endpoint related interrupts. Optional properties: -- epobufsizes : An array of buffer sizes for OUT endpoints. If the property is - not present, or for endpoints outside of the array, 1024 is assumed by - the driver. - -- epibufsizes : An array of buffer sizes for IN endpoints. If the property is - not present, or for endpoints outside of the array, 1024 is assumed by - the driver. +- epobufsizes : Array of buffer sizes for OUT endpoints when they differ + from the default size of 1024. The array is indexed by the OUT endpoint + number. If the property is present it typically contains one entry for + each OUT endpoint of the core. Fewer entries overrides the default sizes + only for as many endpoints as the array contains. + +- epibufsizes : Array of buffer sizes for IN endpoints when they differ + from the default size of 1024. The array is indexed by the IN endpoint + number. If the property is present it typically contains one entry for + each IN endpoint of the core. Fewer entries overrides the default sizes + only for as many endpoints as the array contains. For further information look in the documentation for the GLIB IP core library: http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt index 5ea26c631e3..2826f2af503 100644 --- a/Documentation/devicetree/bindings/usb/msm-hsusb.txt +++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt @@ -15,3 +15,81 @@ Example EHCI controller device node: usb-phy = <&usb_otg>; }; +USB PHY with optional OTG: + +Required properties: +- compatible: Should contain: + "qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY + "qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY + +- regs: Offset and length of the register set in the memory map +- interrupts: interrupt-specifier for the OTG interrupt. + +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "phy" USB PHY reference clock + "core" Protocol engine clock + "iface" Interface bus clock + "alt_core" Protocol engine clock for targets with asynchronous + reset methodology. (optional) + +- vdccx-supply: phandle to the regulator for the vdd supply for + digital circuit operation. +- v1p8-supply: phandle to the regulator for the 1.8V supply +- v3p3-supply: phandle to the regulator for the 3.3V supply + +- resets: A list of phandle + reset-specifier pairs for the + resets listed in reset-names +- reset-names: Should contain the following: + "phy" USB PHY controller reset + "link" USB LINK controller reset + +- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of + 1 - PHY control + 2 - PMIC control + +Optional properties: +- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" + +- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device + Mode Eye Diagram test. Start address at which these values will be + written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as + "do not overwrite default value at this address". + For example: qcom,phy-init-sequence = < -1 0x63 >; + Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1. + +- qcom,phy-num: Select number of pyco-phy to use, can be one of + 0 - PHY one, default + 1 - Second PHY + Some platforms may have configuration to allow USB + controller work with any of the two HSPHYs present. + +- qcom,vdd-levels: This property must be a list of three integer values + (no, min, max) where each value represents either a voltage + in microvolts or a value corresponding to voltage corner. + +Example HSUSB OTG controller device node: + + usb@f9a55000 { + compatible = "qcom,usb-otg-snps"; + reg = <0xf9a55000 0x400>; + interrupts = <0 134 0>; + dr_mode = "peripheral"; + + clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>, + <&gcc GCC_USB_HS_AHB_CLK>; + + clock-names = "phy", "core", "iface"; + + vddcx-supply = <&pm8841_s2_corner>; + v1p8-supply = <&pm8941_l6>; + v3p3-supply = <&pm8941_l24>; + + resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>; + reset-names = "phy", "link"; + + qcom,otg-control = <1>; + qcom,phy-init-sequence = < -1 0x63 >; + qcom,vdd-levels = <1 5 7>; + }; diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 38b2faec419..38d9bb8507c 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -44,7 +44,9 @@ Board specific device node entry }; OMAP DWC3 GLUE - - compatible : Should be "ti,dwc3" + - compatible : Should be + * "ti,dwc3" for OMAP5 and DRA7 + * "ti,am437x-dwc3" for AM437x - ti,hwmods : Should be "usb_otg_ss" - reg : Address and length of the register set for the device. - interrupts : The irq number of this device that is used to interrupt the diff --git a/Documentation/devicetree/bindings/usb/usb-ehci.txt b/Documentation/devicetree/bindings/usb/usb-ehci.txt index ff151ec084c..43c1a4e0676 100644 --- a/Documentation/devicetree/bindings/usb/usb-ehci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ehci.txt @@ -15,6 +15,7 @@ Optional properties: - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair - phy-names : "usb" + - resets : phandle + reset specifier pair Example (Sequoia 440EPx): ehci@e0000300 { diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt index 45f67d91e88..b968a1aea99 100644 --- a/Documentation/devicetree/bindings/usb/usb-ohci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -12,6 +12,7 @@ Optional properties: - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair - phy-names : "usb" +- resets : phandle + reset specifier pair Example: diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 90f8f607d12..5a79377c6a9 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -1,11 +1,17 @@ USB xHCI controllers Required properties: - - compatible: should be "generic-xhci" (deprecated: "xhci-platform"). + - compatible: should be one of "generic-xhci", + "marvell,armada-375-xhci", "marvell,armada-380-xhci", + "renesas,xhci-r8a7790", "renesas,xhci-r8a7791" (deprecated: + "xhci-platform"). - reg: should contain address and length of the standard XHCI register set for the device. - interrupts: one XHCI interrupt should be described here. +Optional property: + - clocks: reference to a clock + Example: usb@f0931000 { compatible = "generic-xhci"; diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt index a018da4a7ad..221ac0dbc67 100644 --- a/Documentation/devicetree/bindings/usb/usb3503.txt +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -15,6 +15,14 @@ Optional properties: - reset-gpios: Should specify GPIO for reset. - initial-mode: Should specify initial mode. (1 for HUB mode, 2 for STANDBY mode) +- refclk: Clock used for driving REFCLK signal (optional, if not provided + the driver assumes that clock signal is always available, its + rate is specified by REF_SEL pins and a value from the primary + reference clock frequencies table is used) +- refclk-frequency: Frequency of the REFCLK signal as defined by REF_SEL + pins (optional, if not provided, driver will not set rate of the + REFCLK signal and assume that a value from the primary reference + clock frequencies table is used) Examples: usb3503@08 { diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index abc308083ac..941980474e1 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -13,6 +13,7 @@ allwinner Allwinner Technology Co., Ltd. altr Altera Corp. amcc Applied Micro Circuits Corporation (APM, formally AMCC) amd Advanced Micro Devices (AMD), Inc. +ams AMS AG amstaos AMS-Taos Inc. apm Applied Micro Circuits Corporation (APM) arm ARM Ltd. @@ -73,12 +74,14 @@ lantiq Lantiq Semiconductor lg LG Corporation linux Linux-specific binding lsi LSI Corp. (LSI Logic) +lltc Linear Technology Corporation marvell Marvell Technology Group Ltd. maxim Maxim Integrated Products microchip Microchip Technology Inc. mosaixtech Mosaix Technologies, Inc. moxa Moxa mpl MPL AG +mundoreader Mundo Reader S.L. mxicy Macronix International Co., Ltd. national National Semiconductor neonode Neonode Inc. @@ -98,6 +101,7 @@ powervr PowerVR (deprecated, use img) qca Qualcomm Atheros, Inc. qcom Qualcomm Technologies, Inc qnap QNAP Systems, Inc. +radxa Radxa raidsonic RaidSonic Technology GmbH ralink Mediatek/Ralink Technology Corp. ramtron Ramtron International @@ -123,10 +127,12 @@ stericsson ST-Ericsson synology Synology, Inc. ti Texas Instruments tlm Trusted Logic Mobility +toradex Toradex AG toshiba Toshiba Corporation toumaz Toumaz usi Universal Scientifc Industrial Co., Ltd. v3 V3 Semiconductor +variscite Variscite Ltd. via VIA Technologies, Inc. voipac Voipac Technologies s.r.o. winbond Winbond Electronics corp. |